The Classical Stefan Problem: basic concepts, modelling and analysis (North-Holland Series in Applied Mathematics and Mechanics)

The Classical Stefan Problem Basic Concepts, Modelling and Analysis NORTH-HOLLAND SERIES IN APPLIED MATHEMATICS AND ...

Author: S.C. Gupta

26 downloads 467 Views 5MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

The Classical Stefan Problem Basic Concepts, Modelling and Analysis

NORTH-HOLLAND SERIES IN

APPLIED MATHEMATICS AND MECHANICS EDITORS:

J.D. ACHENBACH Northwestern University

F. MOON Cornell University

K. SREENIVASAN Yale University

E. VAN DER GIESSEN Un ivers ityofG ron ingen

L. VAN WIJNGAARDEN Twente University of Technology

J.R. WILLIS University of Cambridge

VOLUME 45

ELSEVIER AMSTERDAM - BOSTON - HEIDELBERG - LONDON - NEW YORK - OXFORD PARIS - SAN DIEGO - SAN FRANCISCO - SINGAPORE - SYDNEY - TOKYO

The Classical Stefan Problem Basic Concepts, Modelling and Analysis

S.C. GUPTA Professor (Retd), Department of Mathematics, Indian Institute of Science, Bangalore, India

ELSEVIER 2003

AMSTERDAM - BOSTON - HEIDELBERG - LONDON - NEW YORK - OXFORD PARIS - SAN DIEGO - SAN FRANCISCO - SINGAPORE - SYDNEY - TOKYO

ELSEVIER SCIENCE B.Y Sara Burgerhartstraat 25 P.O. Box 211, 1000 AE Amsterdam, The Netherlands © 2003 Elsevier Science B.Y All rights reserved. This work is protected under copyright by Elsevier Science, and the following terms and conditions apply to its use: Photocopying Single photocopies of single chapters may be made for personal use as allowed by national copyright laws. Permission of the Publisher and payment of a fee is required for all other photocopying, including multiple or systematic copying, copying for advertising or promotional purposes, resale, and all forms of document delivery. Special rates are available for educational institutions that wish to make photocopies for non-profit educational classroom use. Permissions may be sought directly from Elsevier's Science & Technology Rights Department in Oxford, UK: phone: (+44) 1865 843830, fax (+44) 1865 853333, e-mail: [email protected]. You may also complete your request on-line via the Elsevier Science home page (http://www.elsevier.com), by selecting 'Customer Support' and then 'Obtaining Permissions'. In the USA, users may clear permissions and make payments through the Copyright Clearance Center, Inc., 222 Rosewood Drive, Danvers, MA 01923, USA; phone: (+1) 978 7508400, fax: (+1) 978 7504744, and in the UK through the Copyright Licensing Agency Rapid Clearance Service (CLARCS), 90 Tottenham Court Road, London WIP OLP, UK; phone: (+44) 207 631 5555; fax: (+44) 207 631 5500. Other countries may have a local reprographic rights agency for payments. Derivative Works Tables of contents may be reproduced for internal circulation, but permission of Elsevier Science is required for external resale or distribution of such material. Permission of the Publisher is required for all other derivative works, including compilations and translations. Electronic Storage or Usage Permission of the Publisher is required to store or use electronically any material contained in this work, including any chapter or part of a chapter. Except as outlined above, no part of this work may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without prior written permission of the Publisher. Address permissions requests to: Elsevier's Science & Technology Rights Department, at the phone, fax and e-mail addresses noted above. Notice No responsibility is assumed by the Publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. Because of rapid advances in the medical sciences, in particular, independent verification of diagnoses and drug dosages should be made.

First edition 2003

Library of Congress Cataloging in Publication Data A catalog record from the Library of Congress has been applied for. British Library Cataloguing in Publication Data A catalogue record from the British Library has been applied for.

ISBN: 0-444-51086-9 ISSN: 0167-5931 (Series) @ The paper used in this publication meets the requirements of ANSI/NISO Z39.48-1992 (Permanence of Paper). Printed in The Netherlands.

Dedicated to Free Boundary Fraternity

This Page Intentionally Left Blank

Contents

Chapter 1. The Stefan Problem and its Classical Formulation 1.1 1.2 1.3 1.4

Sonic, Strfaii and St(:fiili-lik(, Prolilcills Free Boimtlary Problcrris with Frcc Bouiitlaries of Cotliiiiciisioii-two Thc, Classical Stefan Prol)lciii in Oiic-tlinieiisiori and t,hc Neuniaiiii Solutiorr St(!f;iIi Prol)lcrns Classical Forrnrilatiori of ~liilt,i-tliiiic~nsio~i~~l 1.4.1 Two-Phase Stcfm prol)lciii iii iiinltiplctliriieiisioiis 1.4.2 Alt,erriate forms of the Stcfui c:oiidit,iori 1.4.3 Tlic Kirchhoff’s t,ransfoririiition 1.4.4 Boundary conditions at the fixed liountlary 1.4.5 Conditions at the free lioiiiidary 1.4.6 The classical solutiori 1.4.7 Conservation laws and the iiiotion of the melt,

1 1 18 19 23 23 28 29 30 33 34 35

Chapter 2. Thermodynamical and Metallurgical Aspects of Stefan Problems

39

2.1 Therrnodynamical Aspects 2.1.1 Microscopic arid niacroscopic models 2.1.2 Laws of classical thermodynamics 2.1.3 Some thermodynamic variables and thermal parameters 2.1.4 Equilibriuni temperature; Clapeyron’s equation 2.2 Some Metallurgical Aspects of Stefan Problems 2.2.1 Nucleation aiid superc:ooling 2.2.2 The effect of interface curvature 2.2.3 Nucleation of melting, effect of interface kinetics, aiid glassy solids 2.3 Morphological Instability of tlic Solid--Liquid Interface 2.4 Non-material Singular Surface: Generalized Stefan Condition

39 39 40 42 45 47 47 49 51 52 55

Chapter 3. Extended Classical Formulations of n-phase Stefan Problems with n 2 1

61

3.1 One-phase Problcrris 3.1.1 An extended formnlatiori of one-diineiisional one-phase problcin 3.1.2 Solidification of supercooled liquid 3.1.3 Miilt,i-diincnsioiia1 oiic.-pliasc problcms 3.2 Ext,critlctl Classical Forniu1;Ltioiis of T w o - p h a ~St.(’fiiil ~ Prol,l(mis 3.2.1 A I I cxtcntlcd forniiil;it,ioii of tho oii(~-(liiii(~iisioii~il t.wo-pliasc prohlciii 3.2.2 R’Iiilti-diiiiciisioii~L1Stcfaii pro1)lenis of classcs I1 iuitl 111 :1.2.:3 C1;issiciil St,cfiLii prol)lriiis wit,h Ir-pliascs, t!. > 2 3.2.4 Solitlificatiori wit I i t r;iiisit,ioii t c w p ( w t . i i r c raiigo vii

61 61 63 64 66 Mi GX

70 73

viii

Contents

3.3 Stefan problems with Implicit Free Boundary Conditions 3.3.1 Schatz transformations and implicit free boundary conditions 3.3.2 Unconstrained and constrained oxygen-diffusion problem (ODP)

76 77 81

Chapter 4. Stefan Problem with SupercooUng: Classical Formulation and Analysis

85

4.1 Introduction 4.2 A Phase-field Model for Solidification using Landau Ginzburg Free Energy Functional 4.3 Some Thermodynamically Consistent Phase-field and Phase Relaxation Models of Sohdification 4.4 Solidification of Supercooled Liquid Without Curvature Effect and Kinetic Undercoohng: Analysis of the Solution 4.4.1 One-dimensional one-phase sohdification of supercooled hquid (SSP) 4.4.2 Regularization of blow-up in SSP by looking at CODP 4.4.3 Analysis of problems with changes in the initial and boundary conditions in SSP 4.5 Analysis of Supercooled Stefan Problems with the Modified Gibbs Thomson Relation 4.5.1 Introduction 4.5.2 One-dimensional one-phase supercooled Stefan problems with the modified Gibbs-Thomson relation 4.5.3 One-dimensional two-phase Stefan problems with the modified Gibbs-Thomson relation 4.5.4 Multi-dimensional supercooled Stefan problems and problems with the modified Gibbs-Thomson relation 4.5.5 Weak formulation with supercooling and superheating effects

85 86 94 104 104 107 109 112 112 113 115 121 126

Chapter 5. Superheating due to Volumetric Heat Sources: The Formulation and Analysis

129

5.1 The Classical Enthalpy Formulation of a One-dimensional Problem 5.2 The Weak Solution 5.2.1 Weak solution and its relation to a classical solution 5.2.2 Structure of the mushy region in the presence of heat sources 5.3 Blow-up and Regularization

129 133 133 137 139

Chapter 6. Steady-State and Degenerate Classical Stefan Problems

142

6.1 Some Steady-state Stefan Problems 6.2 Degenerate Stefan Problems 6.2.1 Quasi-static Stefan problem and its Relation to the Hele- Shaw problem

142 143 146

Contents

ix

Chapter 7. Elliptic and Parabolic Variational Inequalities

148

7.1 Introduction 7.2 T h e Elliptic Variational Inequality 7.2.1 Definition and the basic function spaces 7.2.2 Minimization of a functional 7.2.3 T h e complementarity problem 7.2.4 Some existence and uniqueness results concerning elliptic inequalities 7.2.5 Equivalence of different inequality formulations of an obstacle problem of the string 7.3 T h e Parabolic Variational Inequality 7.3.1 Formulation in appropriate spaces 7.4 Some Variational Inequality Formulations of Classical Stefan Problems 7.4.1 One-phase Stefan problems 7.4.2 A Stefan problem with a quasi-variational inequality formulation 7.4.3 T h e variational inequality formulation of a two-phase Stefan problem

148 149 149 152 153 156

Chapter 8. The Hyperbolic Stefan Problem 8.1 Introduction 8.1.1 Relaxation time and relaxation models 8.2 Model I: Hyperbolic Stefan Problem with Temperature Continuity at the Interface 8.2.1 The mathematical formulation 8.2.2 Some existence, uniqueness and well-posedness results 8.3 Model II: Formulation with Temperature Discontinuity at the Interface 8.3.1 T h e mathematical formulation 8.3.2 T h e existence and uniqueness of the solution and its convergence as r ^ 0 8.4 Model III: Delay in the Response of Energy to Latent and Sensible Heats 8.4.1 T h e classical and the weak formulations

166 170 170 174 174 187 191

196 196 197 199 199 203 207 207 209 216 216

Chapter 9. Inverse Stefan Problems

224

9.1 Introduction 9.2 Well-posedness of the solution 9.2.1 Approximate solutions 9.3 Regularization 9.3.1 T h e regularizing operator and generalized discrepancy principle 9.3.2 T h e generalized inverse 9.3.3 Regularization methods 9.3.4 R a t e of convergence of a regularization method 9.4 Determination of Unknown Parameters in Inverse Stefan Problems 9.4.1 Unknown parameters in the one-phase Stefan problems 9.4.2 Determination of unknown parameters in the two-phase Stefan problems

224 225 229 231 231 234 235 243 244 245 248

X

Contents

9.5 Regularization of Inverse Heat Conduction Problems by Imposing Suitable Restrictions on the solution 9.6 Regularization of Inverse Stefan Problems Formulated as Equations in the form of Convolution Integrals 9.7 Inverse Stefan Problems Formulated as Defect Minimization Problems

249 252 257

Chapter 10. Analysis of the Classical Solutions of Stefan Problems

271

10.1 One-dimensional One-phase Stefan Problems 10.1.1 Analysis using integral equation formulations 10.1.2 Infinite differentiability and analyticity of the free boundary 10.1.3 Unilateral boundary conditions on the fixed boundary: Analysis using finite-difference schemes 10.1.4 Cauchy-type free boundary conditions 10.1.5 Existence of self-similar solutions of some Stefan problems 10.1.6 T h e effect of density change 10.2 One-dimensional Two-phase Stefan Problems 10.2.1 Existence, uniqueness and stability results 10.2.2 Differentiabihty and analyticity of the free boundary in the one-dimensional two-phase Stefan problems 10.2.3 One-dimensional n-phase Stefan problems with n > 2 10.3 Analysis of the Classical Solutions of Multi-dimensional Stefan Problems 10.3.1 Existence and uniqueness results valid for a short time 10.3.2 Existence of the classical solution on an arbitrary time interval

272 272 286

Chapter 11. Regularity of the Weak Solutions of Some Stefan Problems

291 295 298 299 300 300 311 312 315 315 321

322

11.1 Regularity of the Weak solutions of One-dimensional Stefan Problems 11.2 Regularity of the Weak solutions of Multi-dimensional Stefan Problems 11.2.1 T h e weak solutions of some two-phase Stefan problems in R", n > 1 11.2.2 Regularity of the weak solutions of one-phase Stefan problems in W\ n > 1

322 329 329

Appendix A. Preliminaries

338

Appendix B. Some Function Spaces and Norms

345

Appendix C. Fixed Point Theorems and Maximum Principles

349

333

Appendix D. Sobolev Spaces

351

Bibliography

355

Captions for Figures

381

Subject Index

383

List of Symbols Some symbols and abbreviations which are common throughout the book are given below. They have also been explained in the text, occasionally, but not every time they occur. In addition to these symbols, several other symbols have been used in the text, and they have been explained at the places they occur. The parameters occurring in the equations could be dimensionless quantities or may have dimensions. At those places where the equations are in the dimensionless form, the method of dimensionalization has been mentioned. For the notations used for the function spaces, the reader is referred to Appendices A—D. The same have been explained in the text, occasionally. Standard notations have been used for the numbering of equations, figures, definitions and propositions. For example, (7.2.7) refers to the seventh equation in the second section of chapter 7. c(x, t)

Concentration,

[kg/m^]

C

Specific heat,

Cy

Specific heat at constant volume

[Jtcg-'^K'^]

Cp

Specific heat at constant pressure

C

Heat capacity,

e

Specific internal energy,

[JK~^/nr'] [Jkg~^]\ also used for energy per unit volume

(indicated in the text) H

Enthalpy,

[J]; also enthalpy per unit volume (indicated in the text)

h

Specific enthalpy,

ht

Heat transfer coefficient,

k

Thermal diffusivity,

K

Thermal conductivity in the isotropic case,

Kij

[Jkg''^] \WK'^/m^]

[m^s~^] [Jrn"^s~^K~^]

Thermal conductivity coefficients in an anisotropic case; z = 1, 2, 3 and J = 1,2,3

Kc

Mean curvature of the free boundary,

[m~^]

I

Latent heat of fusion,

Im I

Latent heat per unit mole, I + {CL - Cs)T,,,

7?"

11 > 1, r(uil n-dimensional space, R or R^ used for real line

S{t)

X ^ S[t) (:r = S[y,zj)), equation of the phas(^-change boundary in one-dimension (three-diuKnisions)

[Jkg'^] [J/A; rrwl]

s

Specific entropy,

[Jkg

'A' ^]

S

Entropy,

[JK-^]

t

real time,

[.s]

T

Temperatnre,

Tm

Ideal equilibrium melting/freezing temperature, also taken as 0 or 1

T,^,

Equilibrium phase change temperature in supercooling/superheating

KTJ

Molar volume,

ft

unit normal vector

[°K]

[m'^/kmol]

Subscripts (L, S, M)

Stand for liquid, solid and mushy regions, respectively

2 = 1,2

quantities in the two phases

Greek symbols p

Density,

[kg/m'^]

a

Surface tension,

[Nm~^]

Some other symbols

/

Differentiation with respect to the argument Time derivative

v/ V2

Gradiant of a scalar function Laplacian operator

erf(x)

Error function

erfc(x)

l-erf(x)

Abbreviations meas (A)

measure of the set A

CEF

Classical enthalpy formulation

CES

Classical enthalpy solution

CO D P

Constrained oxygen-diffusion problem

CSS

Classical St,(^fan solution

HSP

Hele-Shaw problem

ODP

Oxygen-diffusion problem

QSSP

Quasi steady-state problem

SPF

Standard phase-field model

SSP

Supercooled Stefan problem

UODP

Unconstrained O D P

WS

Weak solution


Preface This volume emphasises studies related to classical Stefan problems. The term "Stefan problem" is generally used for heat transfer problems with phase-changes such as from the hquid to the solid. Stefan problems have some characteristics t h a t are typical of them, but certain problems arising in fields such as mathematical physics and engineering also exhibit characteristics similar to them. The term "classical" distinguishes the formulation of these problems from their weak formulation, in which the solution need not possess classical derivatives. Under suitable assumptions, a weak solution could be as good as a classical solution. In hyperbolic Stefan problems, the characteristic features of Stefan problems are present but unlike in Stefan problems, discontinuous solutions are allowed because of the hyperbolic nature of the heat equation. The numerical solutions of inverse Stefan problems, and the analysis of direct Stefan problems are so integrated t h a t it is difficult to discuss one without referring to the other. So no strict line of demarcation can be identified between a classical Stefan problem and other similar problems. On the other hand, including every related problem in the domain of classical Stefan problem would require several volumes for their description. A suitable compromise has to be made. The basic concepts, modehing, and analysis of the classical Stefan problems have been extensively investigated and there seems to be a need to report the results at one place. This book attempts to answer t h a t need. Within the framework of the classical Stefan problem with the emphasis on the basic concepts, modelling and analysis, I have tried to include some weak solutions and analytical and numerical solutions also. The main considerations behind this are the continuity and the clarity of exposition. For example, the description of some phase-field models in Chapter 4 arose out of this need for a smooth transition between topics. In the mathematical formulation of Stefan problems, the curvature eff"ects and the kinetic condition are incorporated with the help of the modified Gibbs-Thomson relation. On the basis of some thermodynamical and metallurgical considerations, the modified Gibbs-Thomson relation can be derived, as has been done in the text, but the rigorous mathematical justification comes from the fact that this relation can be obtained by taking appropriate limits of phase-field models. Because of the unacceptability of some phase-field models due their so-called thermodynamical inconsistency, some consistent models have also been described. This completes the discussion of phase-field models in the present context. Making this volume self-contained would require reporting and deriving several results from tensor analysis, differential geometry, non-equilibrium thermodynamics, physics and functional analysis. I have chosen to enrich the text with appropriate references so as not to enlarge the scope of the book. The proofs of propositions and theorems are often lengthy and different from one another. Presenting them in a condensed way may not be of much help to the reader. Therefore only the main features of proofs and a few results have been presented to suggest the essential flavour of the theme of investigation.

However at each place, appropriate references have been cited so that inquisitive readers can follow them on their own. Each chapter begins with basic concepts, objectives and the directions in which the subject matter has grown. This is followed by reviews-in some cases quite detailed—of published works. In a work of this type, the author has to make a suitable compromise between length restrictions and understandability. I have followed my best judgement in this regard. I hope the readers will appreciate my efforts.

S.C. Gupta, Email :

Bangalore

[email protected]

Acknowledgements I gratefully acknowledge the financial support from the Department of Science and Technology, Ministry of Science and Technology, Government of India, without which it would not have been possible for me to undertake this book-writing project. The administration of the Indian Institute of Science, Bangalore, and the Department of Mathematics, provided infrastructural support for which I am extremely thankful. During my visit to the University of Oulu, Finland, in 1997, I collected lot of material relevant for this book. I sincerely thank my host. Professor Erkki Laitinen and Department of Mathematics, Oulu, for their kind hospitality. The idea of writing this book nucleated during my visit to University of Rosario, Argentina, in 1991, and fructified eleven years later. I thank Professor D.A. Tarzia, Department of Mathematics, Universidad Austral, Rosario, for sending me the bibliography prepared by him, and some reprints which I could not get from other sources. I am grateful to Professor Adimurthi, Department of Mathematics, TIER, at IISc, Bangalore, and professor A.K. Lahiri, Department of Metallurgy, Indian Institute of Science, Bangalore, for reading and responding to some portions of this book. My grateful thanks to Dr. Thomas Chacko, Professor of English and Communication Skills, Department of Management Studies, for style editing this volume with a great deal of attention. There are many old friends and well-wishers who sent reprints and preprints that proved very useful for me. Without naming them individually, I thank all of them for their selfless help. I thank the Pubhshing Editor and staff of Elsevier and the Series Editor Professor J.D. Achenbach of the book series 'Applied Mathematics and Mechanics' for their cooperation. The excellent typing in Latex and drawing of figures in computer graphics were done by Susheel Graphics, Bangalore. Without their cooperation the work would not have taken the final shape.


Chapter 1 The Stefan Problem and its Classical Formulation 1.1

Some Stefan and Stefan-like Problems

The term Stefan problem can be best understood with the help of an example for which the reader is referred to § 1.3. Our concern in the present section is to understand the notion of a free boundary which is a typical feature of the Stefan and Stefan-like problems. Therefore this chapter begins with some examples of Stefan and Stefan-like problems which demonstrate the existence of an unknown boundary, commonly known in the literature as a 'free boundary' or a moving boundary. In the context of solidification/melting problems, with which Stefan problems are commonly associated, the free boundary is also called a phase-change boundary or a melting front or a freezing front Some authors use the term free boundary when the unknown boundary is static and moving boundary when it is time dependent. In this volume we do not make any distinction between 'free' and 'moving' boundaries. The term boundary is used for a surface also. In many of the examples considered in this section, the identification of the free boundary and the mathematical formulation of the problem are rather easy but in some of them even the identification of the free boundary is difficult. The problems given here are from various fields of mathematics, physics and engineering and demonstrate the existence of free boundaries. Our interest in examples given in this section is more on demonstrating the existence of a free boundary and its typical characteristics than justifying the formulation. Problem 1.1.1.

Steady-state heat conduction with a free boundary

Find the steady-state temperature T(x, y) satisfying the equation d^T

d''T

in an open bounded region D C R^. The boundary dD of D consists of two disjoint 1

2

The Stefan Problem and its Classical

Formulation

parts Ri and R2, i.e., dD = RiU R2, where Ri is unknown and R2 is known. On R2, the temperature is prescribed as T{x,y)\R,=f(x,y).

(1.1.2)

If f{x, y) is known throughout the plane, then one boundary conditions on Ri will be T{x,y)\R,=f{x,y),

(1.1.3)

and another boundary condition can be imposed as [Ij, v ( r - / ) | „ , =0.

(1.1.4)

T h e problem is to determine the temperature T(x, y) in D, and the unknown boundary Ri. Two boundary conditions are to be prescribed on Ri. One, because it is a boundary and one more boundary condition is required to determine an unknown boundary. Note t h a t Ri can be determined only by solving the system (1.1.1)—(1.1.4). Such an unknown boundary is called a free boundary or a moving boundary. In 'boundary value problems' of mathematical physics, the boundary of the region under consideration is completely known. Conditions (1.1.3) and (1.1.4) are called free boundary conditions and (1.1.2) is a fixed boundary condition. Although the equation (1.1.1) is linear, free boundary problems are nonlinear problems because of the nonlinearity of the boundary conditions at the free boundary. P r o b l e m 1.1.2.

S t e a d y - S t a t e PVee Surface F l o w w i t h Surface T e n s i o n

Consider a two-dimensional steady, incompressible, irrotational flow in a long channel. X and y axes are taken along the length and depth of the channel, respectively, with the b o t t o m of the channel taken as ?/ = 0 and the upper surface of water, as a free surface or a free boundary denoted by y = '^(^), where ri{x) is unknown. If u{x,y) and v{x,y) are the velocity components in x and y directions, respectively, then du dv - — h 77~ = 0 ox oy dv — ox

du —— = 0 oy

. r • • \ (equation oi contmuity) ,

(irrotationality condition) .

/i -. r\ (1.1.5)

(1.1.6)

The pressure p is given by the following Bernoulli equation [2] H = y + pl(pg) + \q\'l(2g),

(1.1.7)

where, H is the given total water head of water, p is the density, g the acceleration due to gravity and ^ i s the velocity vector. If the bottom of the channel is a rigid boundary, then v = Q, on ?/ = 0.

(1.1.8)

1.1. Some Stefan and Stefan-like Problems

3

At the free boundary y = r/(x), i / = 7/(x)+p/(p^) + |g|V(2p), p = p-a/R,

(1.1.9)

and q-n = 0.

(1.1.10)

Here, p is the atmospheric pressure (known), a is the surface tension (known) and Re is the radius of curvature of the free surface, taken as positive when the center of curvature is situated above the free surface and n is the unit outward normal to the free surface. Re can be expressed in terms of derivatives of r]{x). Free boundary has been taken as static in this problem. Equation (1.1.10) implies that the normal component of the fluid velocity at the free boundary is zero. Problem 1.1.3.

Free Surface Flow^ with Time Dependent Free Surface

Let the free surface in Problem 1.1.2. be time dependent and represented by y = r]{x,t) with ri\t=o being given. Surface tension effects will be neglected. If the velocity field îs expressed as f=V(/>,

(1.1.11)

then from (1.1.5) and (1.1.6) it is easy to conclude that 0(x, t) satisfies the equation

§ + 0 = 0' ''W 0 .

(1.1.41)

1.1. Some Stefan and Stefan-like

Problems

7

If a ^ (O^l]^ then m G [2,oo). Equation (1.1.41) is the porous media equation and it arises also in other contexts such as population dynamics and plasma physics [7j. In order to calculate the mass flux of the gas, the r.h.s. of (1.1.41) can be written as V^p"^) = div(m/?^-^ gradp),

(1.1.42)

jjip-m-i gj-ajp is the mass flux and mp^~^ can be taken as diffusivity. Diff'usivity vanishes as the density p tends to zero. Therefore (1.1.41) is a nonlinear degenerate equation in the neighbourhood of any point where p = 0 but is non-degenerate and uniformly parabolic (see [9] and (7.3.26)) in the neighbourhood of any point at which p is away from zero. Such problems are called degenerate parabolic-elliptic problems. An important consequence of nonlinear degeneracy is t h a t there is a finite speed of propagation of a disturbance from rest which is in contrast to the parabolic heat equation in which the speed of heat propagation is infinite. The finite speed of propagation may give rise to waiting time solutions. Equation (1.1.41) is to be supplemented with an initial condition if the region is infinite and with both initial and boundary conditions if the region considered is finite. T h e existence of a free boundary in such problems can be illustrated with the help of the following example. Let - ^ = V^(p^),

- o o < X < oo, t > 0,

(1.1.43)

> 0 for x G i?/ = (ai, 02), —00 < ai < a2 < 00 (1.1.44)

!

- 0 for x G

R\Ri.

This problem, generally, does not have a classical solution. T h e classical solution of a problem can be roughly stated to be a solution in which the dependent variable possesses continuous derivatives of the order required in the problem formulation. The mathematical definition of a classical solution will be discussed later but at present it would suffice to state t h a t the solution p[x,t) of (1.1.43) and (1.1.44) may not possess the required continuous derivatives. For t > 0, gas will be diff"using to the right of x = a2 and to the left oix = ai and thus giving rise to two moving boundaries x = Si[t),i = 1,2. Let Si be moving towards + 0 0 and 5*2 moving towards —00. Using a weak formulation of the above problem in (1.1.43) and (1.1.44), several interesting results on the behavior oi Si{t), z = 1, 2 have been obtained in [10] and [11]. T h e following proposition indicates that in some cases, the interface Si{t) starts moving only after an elapse of time V > 0. P r o p o s i t i o n 1.1.1. There exist numbers t* G [0, +00) for z = 1,2 such that Si{t) is strictly monotone for t G (t*, +cx)) and S^{t)=a,, If t* > 0, then Si{t),

z = 1,2 for t G [0,t*].

(1.1.45)

z = 1, 2 remain stationary for t* units of time [11].

In this case t* is called a waiting time. It has been proved in [11] that the interface is Holder continuous under certain conditions and if the interface is in motion, then one

8

The Stefan Problem and its Classical Formulation

expects it to move with the velocity V of the gas, and ^

W^,(x, t), z = 1, 2; W = - ^ ^ p " ^ - ^

= - lim

(1.1.46)

The hmits in (1.1.46) are taken as x approaches the boundary of the region from within the region in which p{x,t) > 0. Equation (1.1.46) can also be obtained from the mass balance condition at the interface which states that the jump in the density at the interface multiplied by the velocity of the interface is equal to the jump in the mass flux across the interface. In a problem symmetrical with respect to x, it is sufficient to consider the region 0 < X < oo with a single interface x = Si{t) and ai = a2 > 0. Si{t) should satisfy (1.1.46) for z = 1, and another condition to determine the unknown Si{t) may be prescribed as Slit)

a,

fp{x,t)dx=

f p{x,0)dx.

0

(1.1.47)

0

Conditions of the type (1.1.47) are called non-local boundary conditions at the free boundary. X = 0 is now a fixed boundary and the boundary condition on it is given by dp dx

= 0.

(1.1.48)

x=0

Note that we have two conditions prescribed at the free boundary, viz., (1.1.46) and (1.1.47). Problem 1.1.6.

Shock Propagation

The solution of Burger's equation (1.1.49) with boundary condition (1.1.50) has been discussed in [12]. Uy + uu^ = Uy+ 2 a~^^^^ ^ ^' ^^' ^^ ^ ^^' ^ - 0-

(1.1.49)

On ^ = 0, u{x,y)\y^, = f{x),

xeR,

(1.1.50)

0 < X < 1,

(1.1.51)

where

fix)

=

1, x < 0 , 1 -X,

0, x > 1. The characteristic equations of (1.1.49) in parametric form in terms of a parameter t are given by dx dy . du ^ — - 0, - ^ = 1, and — = 0. dt dt dt

_ ^ ^. (1.1.52)


Problems

Let x{s, 0) = s, y{s, 0) = 0 and ^(5, 0) =

f{s).

The solution of (1.1.52) is given by ' 5 + t, s < 0, x{s,t)

( l - s ) t + s, 0 < 5 < 1, ;

••

S,

y = t

(1.1.53)

5 > 1. 1,

s < 0,

( 1 - s ) , 0 < s < 1,

u{s^ t) •

0,

(1.1.54)

s> 1.

The characteristic curves and u{x^y) are shown in Fig. 1.1.1. It is clear from the figure t h a t the characteristic curves intersect in the region x > 1, y > 1 and therefore u{x,t) is not defined (is not single valued) in this region. u{x,y) defined by (1.1.54) ceases to be the classical solution of (1.1.49) in the region x > 1, y > I and (1.1.49) is satisfied in this region only in the weak sense. It may be noted t h a t the solution u{x, y) could be discontinuous in some portion of the region even if / ( x ) is a continuous and differentiable function throughout the region. If (1.1.49) is written as

dP_ aO dy

dx

0,

(1.1.55)

then it can be shown (cf. [12]) that the weak solution is discontinuous across a curve which is called a shock and whose equation is given by

[P]dx - [Q]dy = 0.

(1.1.56)

The notation [/] denotes the difference between the limits of a function / as the shock or a surface of discontinuity of / is approached from both sides. Conditions of the type (1.1.56) are called Rankine-Hugoniot conditions. In the present problem [P] = 1 and [Q] = 1/2, and therefore the shock is given by y = 2x + d. The constant d can be determined if we know the point from which the shock is emanating, for example, in the present problem this point is (1.1) (see Fig. 1.1.2.). Shock is the oldest form of the free boundary and its origin lies in the study of gas dynamics [13]. If (1.1.49) is multiplied by u'^.n > 1, then P and Q in (1.1.55) will change. This change will result in the non-uniqueness of the shock and infinitely many shocks can be obtained. For nonlinear hyperbolic equations of the type (1.1.49), further information in the form of physical arguments involving stability, entropy, dissipation or continuous dependence on the initial d a t a is needed to ensure uniqueness (cf. [14, 15]). There are some important differences between the present problem and the free boundary Problems 1.1.1. to 1.1.5. In the previous five problems, the free boundaries can be

10

The Stefan Problem and its Classical Formulation y4

0

Fig. 1.1.1. Characteristic curves and u{x,y)

X

Fig. 1.1.2. Geometry of the shock

identified without much difficulty and the boundary conditions on them can be imposed after some thought. It is a different matter that the classical solution may or may not exist. In the solution of equations (1.1.49)—(1.1.50), there is no indication of a free boundary. It is only through the construction of the solution that we come to know about the magnitudes of jumps in P and Q. The equation (1.1.56) can be obtained only through the weak solution and not through the classical approach, which was followed in other problems. Problem 1.1.7. Free Boundary Associated with a Frictional Oscillator Problem This interesting free boundary problem has been reported in [15]. As shown in Fig. 1.1.3., a block of mass m rests on a conveyer belt moving with a constant velocity V. The forces acting on the mass are: (1) spring force with a spring modulus 5^, (2) prescribed force F{t) assumed to be sufficiently smooth, and (3) Coulomb frictional force with coefficient of friction /i. The motion of the block with mass m is governed by the equation dx sgn

-V

\+S,

m.

(1.1.57)

where sgn{z)

1 if 2 > 0,

-1 if 2 < 0 ,

(1.1.58)

and g is the acceleration due to gravity. At time t = 0, x and dx/dt are prescribed. Both analytical and numerical solutions of (1.1.57) are extremely difficult as at each instant of time information is required whether dx/dt > y, = y, or < V. The unknown instants of time t = t^, i = 1,2,... or the points x^ = x[ti), z = 1, 2, at which dx/dt = V can be regarded as free boundaries.


Problems

11

When dx/dt = V, d^x/dt'^ = 0. The second derivative becomes discontinuous dX t = t^. Once dx/dt becomes V at ^ = ^^, it will remain so in some interval t^ < t < t* until at t = t*, \F{t) — Smx\ > iim^g. Again at t = t^+i, dx/dt may be equal to V. If so, t = ti+i is a free boundary. If it is assumed that mass does not j u m p and there is no abrupt change in the velocity of the mass, then it can be assumed t h a t x{t) and dx/dt are continuous functions of time and dx/dt — 1/ at the free boundary. These assumptions provide boundary conditions at each free boundary. There is a fundamental difference between this problem and the free boundary Problems 1.1.1. to 1.1.6. In the earlier problems, free boundaries arose due to the physical situations or the mathematical nature of the solution such as a weak solution, but in the present problem free boundaries arise due to discontinuities in the physical properties of the solution.

A Mass

Spring

AI—frnm A

B

> F(t)

Conveyer belt

Fig. 1.1.3. Frictional oscillator P r o b l e m 1.1.8.

I m p a c t of a V i s c o - P l a s t i c B a r o n a R i g i d Wall

A bar of length b made up of visco-plastic incompressible material moving with constant velocity —VQ hits a rigid wall at time ^ = 0. We consider a one-dimensional problem in which X-axis is taken opposite to the initial motion of the bar and the rigid wall is taken at x = 0. After the bar hits the wall, compressional stresses develop in the bar giving rise to visco-plastic flow of the material in the region. If V(x, t) is the velocity of the bar for ^ > 0, then the gradient of V{x, t) or the velocity of deformation can be expressed as follows (cf. [16]). ^

dx

, \r\>

To, To > 0, r < 0, (1.1.59)

0 . , |r| < To.

Here, r represents compressional stress, which is negative as the x-axis is oriented opposite to the direction of motion of the bar, TQ is the stress at the limit point and //, is the coefficient of viscosity of the material.

12


It will be assumed that any disturbance is propagated over the whole bar instantaneously. The equation of motion in the visco-plastic region can be easily obtained by using Newton's second law of motion. We have dV dr ^"dt^'dx^

d^V '^^'

0 < X < So{t), 0 < ^ < t„ 5o(0) = 0,

(1.1.60)

where p is the density of the material and x = So{t) is the interface between elastic and visco-plastic regions. In the elastic region dV — = 0, \T\ 0 in P^-plane. This string is displaced upwards by a rigid body called an obstacle (cf. [22, 15]). A view of the cross section of this system of string and obstacle from above in P^-plane is shown in Fig. 1.1.4. Let y = ip(x) be the equation of the cross section of the obstacle in P^, i.e., the equation of the curve Q1ABQ2. '0(x)

1.1. Some Stefan and Stefan-like Problems

17

is assumed to be sufficiently smooth. We shall relax this smoothness condition later (see § 7.2.5). Let y = u{x) be the equation of the string in the equilibrium position or the equation of the curve P1ABP2. The problem is to find the function u{x) and the arc AB of the string which is in contact with the obstacle and on which u{x) = ip{x). The points A and B are free boundaries and in the present case we can call them 'free points'. Once A and B are determined, the arc AB is also determined because ip{x) is known. The formulation of the problem is as follows: u{0) = u{b) = 0,

(fixed end conditions),

(1.1.92)

u{x) = ip{x) on AB; u{x) > ip{x) on P1ABP2,

(1.1.93)

u'{x) < 0,

(1.1.94)

u{x) > ip{x) =^ u"{x) = 0.

(1.1.95)

The second equation in (1.1.93) implies that the string does not penetrate the obstacle. The concavity of the string as viewed from the x axis imphes (1.1.94) and the tightness of the elastic string implies that the portions Pi A and BP2 are straight lines and so u"{x) = 0. The two boundary conditions at the free boundary can be obtained from the continuity of u and du/dx^ i.e.. [U]A

0,

= [U]B •

(1.1.96)

where [/] stands for the jump in the quantity under consideration at the given point. Equation (1.1.95) is equivalent to the following condition [u{x)-^{x)]u"{x)

= 0.

(1.1.97)

In view of (1.1.93)-(1.1.95), equation (1.1.97) is valid. When u{x) = ip{x), (1.1.97) is satisfied and when u{x) 7^ ip{x) then the second equation in (1.1.93) implies u{x) > il){x) and from (1.1.95), u"{x) = 0 and therefore (1.1.97) is satisfied. If (1.1.97) holds and if u{x) > ipix), then u"{x) = 0, which is (1.1.95). The formulation (1.1.92)-(1.1.95) is equivalent to the formulation given by (1.1.92)—(1.1.94) and (1.1.97). Let us call the formulation (1.1.92)—(1.1.95) as Problem {Ri) and the formulation equivalent to Problem (Ri) as Problem (i?2)- Consider the following minimization problem which is concerned with the minimization of the energy of the above string. J 2

min / u>^ PiJ

-^]dx dx j

, Vw(x) eV,

(1.1.98)

where V = {u : u{0) = u(b) — 0, u and dujdx are continuous, and u satisfies relations (1.1.94) and (1.1.95)}.

18


We shall call this formulation in (1.1.98) as Problem {Rz)- This is a fixed domain formulation as it does not consider separate formulations on different portions of P1ABP2. In view of the equivalence of Problems {R2) and {R3) which will be established in Chapter 7, the formulation {R2) is also called 'variational formulation' of the obstacle problem. A variational inequality formulation of this problem has been given in Chapter 7.

y=vKW A/7 / //N

///////// /////////// /////////// '//////////// ////////////

Po=(b,0)

p,=(ao) Fig. 1.1.4. Obstacle and the stretching of the string.

1.2

Free Boundary Problems with Free Boundaries of Codimension-two

In Problem 1.1.12., the free boundary consists of just two points A and B. Therefore the dimension of the free boundary is zero, whereas the spacial dimension of the problem is two. Another example of a free boundary of codimensional-two (or free points) is the tip of a propagating line crack in an elastic medium. We shall see later in § 3.2.2 that in the problems concerning initiation of solidification/melting along a known surface, codimension-two free boundaries could be time dependent. If the spacial dimension of the problem is n (the problem could be transient) and the dimension of the free boundary is n — 2, then we say that the free boundary is of codimension-two. Several problems with free boundaries of codimension-two have been discussed in [23]. In Problems (1.1.1)(1.1.11), the dimension of the free boundary in only one less than the spacial dimension of the problem. The distinction between the free boundaries of codimension-two and the free boundaries of codimension-one is not superficial but it raises some serious questions [23], some of which are mentioned below. 1. Can these problems with free boundaries of codimension-two, in some sense such as hnearization, be modelled as limits of free boundary problems of codimension-one? 2. What can be said about the existence, uniqueness and regularity of solutions to models as stated ? In particular, is any of the information redundant ?

1.3. The Classical Stefan Problem in One-dimension and the Neumann Solution

19

3. What methodology is available to solve these problems explicitly? No systematic methodology has yet been proposed for nonlinear problems of this type. 4. If solutions exist, are they stable to perturbations in the direction parallel to the free curve? 5. Is there a possibility of generating the models either to make their analysis or numerical solutions easier?

1.3

The Classical Stefan Problem in One-dimension and t h e N e u m a n n Solution

Stefan problems are free boundary problems with some special features which can be easily explained with the help of the following one-dimensional solidification problem. At time t = 0, a pool of liquid at constant temperature To > T^, occupies a semi-infinite region x > 0. Tm is the temperature at constant pressure at which the liquid solidifies. It is called freezing temperature or phase-change temperature. In the case of pure metals such as copper, Tm is called melting temperature also because in the case of pure metals freezing and melting temperatures are the same. Tm is also called equilibrium phasechange temperature as both sohd and liquid phases can stay together in thermodynamic equilibrium dX T = Tm (cf. § 2.1.4.). The fixed boundary a: = 0 is being cooled, for example, temperature T^ < Tm is prescribed at a; = 0. In this case soHdification starts instantaneously at x = 0. For any ^ > 0, the region 0 < x < oo will consist of sohd and hquid phases with the solid phase occupying the region 0 < x < S(t) and the liquid phase the region S{t) < x < oo. S[t) is the free boundary or the phase-change boundary/interface. This solidification problem can be formulated mathematically as follows: In the solid region f)T fP'T CsPs^ = KS-QJ:, Ts{x,t)\,ô

0 < X < 5( 0,

= Tt0.

(1.3.2)

In the liquid region CLPL^

+ CiPLU,^

= K^-^,

<S{t)<x,

TL{x,t)\tô = To, ri.(x,0|.ôc = To.

t>0,

(1.3.3) (1.3.4)

20

The Stefan Problem and its Classical Formulation At x = S{t)

K s ^

- KL^

TS = TL = Tm.

(1.3.5)

= {Ips + {PLCL - PsCs)Tm}^,

(1.3.6)

S{0) = 0.

(1.3.7)

Equations (1.3.1)—(1.3.6) are not dimensionless. Temperatures Tf,, To, Tm and thermophysical parameters p, C, K, and / are known quantities. The subscripts S and L stand for solid and liquid regions. The symbols used in (1.3.1)—(1.3.6) are explained in the 'List of Notations'. The definitions of thermophysical parameters C, K, /, etc., will be discussed later in § 2.1.3. At present, our interest is to highlight some basic features of Stefan problems. Equation (1.3.1) is the Fourier heat conduction equation derived on the basis of Fourier's law given in (1.3.8) for heat conduction in a homogeneous isotropic medium. q=-K

grad T.

(1.3.8)

Here, qis called a heat flux vector and gives the heat flow at a spacial point at any instant of time t- q-n gives heat flow per unit area, per unit time in the direction of the outward drawn unit normal n to the surface of the region under consideration. The derivation of heat conduction equation is given in many books such as [24] and is obtained on the basis of principle of conservation of energy (cf. § 1.4.7). The heat equation (1.3.1) is based on a macroscopic model but it can also be derived on the basis of a microscopic model. The transport of heat energy takes place due to the random motion of molecules. The parabolic heat equation as well as hyperbolic heat equations can also be derived by considering discrete random walks of molecules [25]. If the densities of solid and liquid phases are not equal, then liquid may acquire motion whose velocity u^ in the one-dimensional case can be obtained from the mass balance condition at the interface given below. pLUa: = {pL-ps)-^-

(1-3.9)

If ps > PL, then there will be a shrinkage of total volume in solidification, and u^j, will be negative as dS/dt is positive in the above problem. If ps < PL-, then there will be an expansion of the volume and u^ will be positive as dS/dt is positive. Equation (1.3.3) is the Fourier's heat conduction equation for the liquid in motion. Boundary conditions at the fixed boundary x = 0 could differ from that in (1.3.2) (see § 1.4.4.) but in the 'Neumann solution', a constant temperature is prescribed at x = 0. At t = 0 it was only the liquid phase therefore the initial condition has been prescribed only for the liquid. In the present problem To is a constant. If Tm is a constant, then the conditions in (1.3.5)

1.3. The Classical Stefan Problem in One-dimension and the Neumann Solution

21

are called isotherm conditions. Equation (1.3.6) is the dynamic energy balance condition. Both (1.3.5) and (1.3.6) are based on the assumption of instantaneous achievement of local thermodynamic equilibrium at the phase-change interface. —KidTi/dx is the heat flux from the liquid outwards (the outward normal to liquid at S{t) points into the solid) and —KsdTs/dx is the heat flux from the solid outwards (the outward normal to solid at S{t) points into the liquid). Equation (1.3.6) can be derived by using the energy conservation law. It gives the energy balance at the phase-change boundary. In § 1.4.1, the derivation of the equation (1.3.6) has been obtained in a more general context. When the phase-change takes place from liquid to solid, the latent heat / released by the system is removed by conduction. Equation (1.3.6) is a dynamic compatibility condition and is commonly known as the Stefan condition. It is called a condition of Rankine-Hugoniot type. Equation (1.3.6) can also be stated in the form

OX

[H]^^. liquid

(1.3.10)

liquid

Here, H is the enthalpy per unit volume, which is the sum of the latent heat plus the sensible heat, and Vn is the normal component of the velocity of the interface with the unit normal n pointing into the liquid. Melting Problem The problem discussed in (1.3.1)—(1.3.6) is a solidification problem as the phase changes from hquid to sohd. The melting problem in which the phase changes from sohd to liquid can be easily formulated by making appropriate changes in (1.3.1)—(1.3.6). For example, (1.3.3) is still valid for liquid but liquid region is now 0 < x < S{t). Similarly other equations can be modified. During solidification, the system releases latent heat but during melting the system 'absorbs' latent heat. Since we take / > 0, a minus sign should be put for heat absorbed. Equation (1.3.10) is stiU valid for the problem of melting provided the changed directions of normals to the two regions at the free boundary are taken into account. Since the formulation of both solidification and melting problems has the same mathematical structure, they are said to be mathematically analogous. If a solution to one of them is obtained, then the solution to the other problem can be obtained by making some minor changes in it. It is for this reason that it suffices to study either of them. Neumann Solution The method of analytical solution of (1.3.1)—(1.3.7) which is discussed below is based on some special type of solutions of heat equations (1.3.1) and (1.3.3), which can be written in terms of error and complementary error functions [26]. An exact analytical solution of the Stefan problem even in the one-dimensional case is possible only in few simple cases. If in (1.3.2), To is time dependent or if a constant flux is prescribed at x = 0 then the method discussed below fails to provide a solution. The solution of (1.3.1) can be written

22


'""^"'my^^'''-

2) distinct phases separated by (n — 1) distinct phase-change boundaries, then we have an n-phase Stefan problem. It is not possible to give a precise definition of a Stefan problem but in the light of the above discussion some of the characteristic features of Stefan problems can be described as follows: (1) the transport phenomenon is that of heat transfer governed by parabolic equations, (2) any two distinct phases are separated by a sharp phase-change interface, (3) at the

1.4 Classical Formulation of Multi-dimensional Stefan Problems

23

phase-change boundary, temperature is prescribed which is known, (4) heat flux is discontinuous across the phase-change boundary and the latent heat is released or absorbed at the interface. Phase changes in which the heat flux is discontinuous are known as first-order phase transitions. We shall learn more and more about these characteristic features of Stefan problems as we proceed further. In many physical problems although a free boundary exists, there is some deviation of features in them from the characteristic features of the Stefan problem. It has become almost customary to indicate such problems by a suitable nomenclature. For example, if a hyperbolic equation is considered instead of a parabolic equation, then it is called 'hyperbolic Stefan problem'. Similarly, we have a 'Stefan problem with kinetic condition' if a kinetic condition is introduced at the free boundary or 'Stefan problem with supercoohng' if the liquid is supercooled. The term 'classical' is generally used to distinguish the classical formulation from the weak formulation (§ 5.2 for the weak formulation of the classical Stefan problem). In a classical formulation it is assumed that there exists a suflfiiciently regular sharp interface, which separates two distinct phases. Two phases will be considered different if they differ in their composition, structure, or properties. At the phase-change interface, two boundary conditions are prescribed, one in the form of temperature and the other arising from the energy balance at the interface.

1.4 1.4.1

Classical Formulation of Multi-dimensional Stefan Problems Two-phase Stefan problem in multipledimensions

We shall now extend the mathematical formulation given in (1.3.1)—(1.3.7) to multidimensional problems. For simplicity we consider R^. Consider a heat-conducting openbounded region G C R^ whose boundary dG is smooth, for example dG G C^^^, for some T] > 0. Let G{t) = G x {t} and dG{t) = dG x {t}, 0 < t < t^ < oo ioi some suitable real number t*. G^* = Do ^m-

(1.4.5)


Fig. 1.4.3. Cylinder over G(0) in Fig. 1.4.1.

25

Fig. 1.4.4. Cylinder over G{0) in Fig. 1.4.2.

Initial conditions T,(x,0) = /,(x), X e G^{0), 2 = 1, 2,

(1.4.6)

/i < Tm and /2 > Tm. Isotherm conditions on 3 is simple. Many generalizations of this formulation are possible and some of them will be discussed later.

30


1.4.4

Boundary conditions at the fixed boundary

(A) Standard boundary conditions (AI) Type I boundary condition In the boundary condition of this type temperature is prescribed. Let dG be the boundary of the region G C R^. Type I boundary condition is of the form T\dG = /(x, y^z,t),t>

0, (x, y, z) e dG.

(1.4.33)

If / < Tm{> Tm) then sohdification (melting) starts instantaneously i.e., there is no waiting time for the phase-change to take place. Since energy can neither be produced nor disappear at infinity if G is unbounded, we have lim T ( x , t ) - T ( x , 0 ) , t > 0.

(1.4.34)

|x|—>oo

In order to obtain a physically meaningful solution to the diffusive heat equation for unbounded domains, it is required that dT lim ^r-(x,t)

- 0 , t>0.

(1.4.35)

Temperature-prescribed boundary conditions are known as Dirichlet type boundary conditions. Sometimes, while constructing approximate solutions more than the prescribed number of boundary conditions are required to match the number of unknowns. In such a case additional boundary conditions are generated. Let us consider a radially symmetric one-dimensional heat conduction problem in which the temperature at r — a is prescribed as T{r,t)\râ = f{t).

(1.4.36)

If (1.4.36) is differentiated with respect to time and the Fourier's heat equation is used, then

dT 'dt

=^ ^

+-^1

=/'W

(1-4.37)

r=a

Equation (1.4.37) provides one more boundary condition for the problem. (All)

Boundary condition of radiative-convective type

This boundary condition can be written as

dn

= 0E{T' - n)\aG + [CxT - C2To)|aG.

(1.4.38)


31

Here, n stands for the unit outward normal, /3 is Stefan-Boltzmann constant, E is the emissivity of the surface which is defined as the ratio of the heat emitted by the body to the black body at the same temperature, To is the ambient temperature, and Ci and C2 are functions of time, p is positive and has dimensions [watt]/[meter]^x [Temperature]"^, 0 < E < 1. From this boundary condition, three types of well known boundary conditions can be obtained as particular cases. If ^ = 0 and Ci = C2 = ht then we have a convective type boundary condition. ht{> 0) is called 'heat transfer coefficient' and has dimensions [Power] / [Temperature] [length]^. If /3 = 0, Ci = 0 and C2T0 = g{t), then we have a flux-prescribed boundary condition. Flux prescribed boundary conditions are known as type II boundary condition. Convective type boundary conditions are called type III boundary conditions and radiative-convective boundary conditions are called type IV boundary conditions. More details about these boundary conditions can be found in [24]. These four types of boundary conditions are commonly prescribed in heat transfer problems. (B) Non-standard boundary conditions (BI) Non-local boundary condition To explain the nature of a non-local boundary condition, we consider a simple onedimensional problem of fluidized-bed coating. Our interest in this problem is more on pointing out the characteristic features of a non-local boundary condition than its rigorous formulation. A thin metallic plate of thickness 26, area Ap and the initial temperature To (To > Tm) is immersed vertically in a pool of plastic coating material [29] which is maintained at temperature Too which is also the temperature away from the boundary layer. The softening temperature of the coating material is Tm > Too- Because of the high thermal conductivity and finite heat capacity of the metallic plate, the plate can be treated as a lumped parameter system in which the temperature can be regarded as a function of time only. Let Tp{t) be the temperature of the plate. In the one-dimensional problem considered here, let the metallic plate be situated at a: = 0. The problem is that of finding the temperature T(x, t) of the softened plastic, temperature Tp[t) and the extent x = 6{t) upto which the plastic has softened. The unknown quantities can be obtained by solving the following system of equations. dT d'^T PfCf-^ = ^ Z - ^ ' 0 < X < 5{t), t > 0,

(1.4.39)

T(0,0) = To, T(0, t) = Tp{t), T{6,t) = Tm.

(1.4.40)

m

A,

-{To - Tp(0) = httiTr, - T^) + pfCf J{T-

where the only work done is by the pressure P in changing the volume. From (2.1.3), we get

C,^{%l.

(.1,5,

It may be noted that Q is not a function of temperature. Therefore C is not the derivative of Q with respect to T but is only the ratio of d'Q and dT or the ratio of very small amount of heat supplied and the change in the temperature. A specific value of an extensive property (a property such as energy which depends on the mass) is its value per unit mass. Specific heat is defined as the heat capacity per unit mass and will be denoted by C. Enthalpy:

If the pressure P does not change in the process, then from (2.1.1), we

get dU = d'Q - PdV.

(2.1.6)

2.1 Thermodynamical Aspects

43

Also dU + PdV = dU-{- PdV + VdP = dU-^ d{PV) = d{U + PV).

(2.1.7)

Let H = U -\- PV, where P is constant. H is called enthalpy and specific enthalpy will be denoted by h. H is a. function of state, or a thermodynamical property. In this volume, H has also been used for enthalpy per unit volume. If a thermodynamic quantity depends only on the state of the system and not on the process by which it has been brought to that state, then it is called a thermodynamical property. Temperature and pressure are examples of thermodynamical properties. From (2.1.6) and (2.1.7), we have dH = dQ = CpdT,

(2.1.8)

Here, Cp is the heat capacity at constant pressure. From the relation dH = dQ (at constant pressure), it is clear that enthalpy can be regarded as the heat content of the system. A positive AH (change in H) means that heat is absorbed while a negative AH means that heat is released. Gibbs free energy and Helmholtz free energy: We now ask 'Is it possible to describe the thermal equilibrium of a system in terms of some property of the system itself even if it is in contact with surroundings' ? A system and its surroundings together is called a 'universe'. Universe is considered to be isolated and closed. For an isolated system, d'Q = 0 and so dS = 0. Let dS and dS^ be the changes in the entropies of the system and its surroundings, respectively, then from the second law of thermodynamics (dS^dS,) >0.

(2.1.10)

Let the system absorb some heat d'Q from its surroundings so that the internal energy of the system changes from U to U -\- dU and the system does some work d'W = PdV in a ^PVT system'. If T is the temperature of the system and its surroundings, then dS, = -d'QIT

and [dS - d'Q/T) > 0.

(2.1.11)

Substituting d'Q from (2.1.1) in (2.1.11), we get dU + PdV -TdS

0,

(2.2.14)

which is the relation (2.2.6).

2.2.3

Nucleation of melting, effect of interface kinetics, and glassy solids

Nucleation of melting: Melting of solid can begin without significant superheating in the solid. When nucleation of melting occurs over a sohd surface, the nucleus consisting of the liquid phase will be enveloped basically by two different surfaces. On one side is a sohd-hquid interface (see Fig. 2.2.2.) and on the other side is a gas-hquid interface. The surface energy of the gas-solid interface is generally greater than the combined gas-liquid and solid-liquid surface energies. This implies that the formation of the liquid film on the solid surface will not be opposed by the solid surface and the liquid film spreads over the solid surface without significant superheating. The equilibrium of surface energies is attained at the equilibrium temperature. Effect of interface kinetics: It was suggested in [41], that the interface movement lowers the temperature of the solid-liquid interface below the equilibrium teriiperature TmThe form of the growing pheise adapts itself to satisfy the growth velocity-temperature requirement. The movement of the interface is dependent on a driving force which was called the viscous effect or the interface kinetic effect. The supercoohng as a function of interface velocity can be expressed as T(V) = Tr,-$-V,

(2.2.15)

where T{V) is the new melting temperature, V is the velocity of the interface and (p is the viscous correction term. For small departures of T{V) from T^ the rate at which solidification occurs is approximately proportional to the departure [42]. In high transition rates these effects appear on a macroscopic scale also. Kinetic undercooling is likely to be important only when V • n (normal velocity) is large, such as V - n ^ lOm/s. The applicability of kinetic effect to a moving interface has been opposed by some authors [43] as the concept devolves from the thermodynamics of equilibrium systems which has been

52

Thermodynamical and Metallurgical Aspects of Stefan Problems Gas-solid Interface

Liquid

Gas-liquid Interface

Solid-liquid Interface

Solid

Fig. 2.2.2. Nucleation of melting applied in (2.2.15) to transforming systems. The interfacial free energy of the solid-liquid interface is a thermodynamic quantity only in the limited context of stationary interfaces which are at equilibrium. See [42] and [44] for further information. Glassy (amorphous) solids: At very high cooling rates, such as those encountered in rapid solidification of liquid metals, there may be insufficient time for the formation of nucleus and a glassy solid is formed. While still non-crystalline, it becomes a solid in its mechanical behaviour as its viscosity becomes very high. There is no phase-change boundary associated with glassy materials.

2.3

Morphological Instability of t h e Solid-Liquid Interface

A crucial assumption in the classical formulation of Stefan problems is that there exists a smooth surface which is the phase-change boundary such that on one side of this surface is a stable solid (liquid) region and the other side a stable liquid (solid) region. The solid region is identified only by its temperature which should be less than or equal to the equilibrium temperature T^. Similarly liquid is identified only by its temperature which should be greater than or equal to T^. The existence of such a planer solid-liquid interface is an ideal situation and is possible only in special cases such as columnar solidification of pure metals or directional solidification of alloys in 'Bridgman type furnace' [40] under a sufficiently high temperature gradient. In unidirectional solidification, in its classical formulation, it has been established mathematically in several references such as in [45] that under certain conditions, such as, in the absence of volumetric heat sources, or non-existence a mushy region initially, a planar interface remains planar (mushy region does not develop) till the solidification is complete. In multi-dimensional problems, the existence of a sharp interface has been proved rigorously only for a short-time under suitable assumptions (see Chapter 10). Invariably, a sharp interface separating a stable solid region from a stable liquid region

2.3 Morphological Instability of the Solid-Liquid Interface

53

degenerates after a short time into a mushy region. The mushy region contains both sohd and hquid phases and separates the stable sohd region from the stable liquid region. The solid in the mushy region is present initially in the form of dendrites (Figs. 2.3.1. and 2.3.2.). Further growth of dendrites leads to a poly crystalline structure with one crystal from each nucleus (Fig. 2.3.3.). The diameter of a grain could be as smah as 10"^m and as large as 10~^m. Mushy region may also develop during solidification if the hquid is supercooled or during melting if the sohd is superheated. This degeneration of sharp interface into a mushy region is attributed to the morphological instability of the solidliquid interface.

Fig. 2.3.1. Formation of dendrites

Fig. 2.3.2. Dendrite growth

Classical thermodynamic definitions of stability are inapplicable to the determination of the morphology of a growing interface, and current extensions of equilibrium thermodynamics have not yet furnished a fully acceptable alternative [46]. On the basis of a heuristics-based stabihty criterion, the interface is said to be morphologically unstable/stable if a small perturbation given to the interface grows/dies with time (see Fig. 2.3.4.). In Fig. 2.3.4. (a), the perturbations are growing, making the planar interface

Fig. 2.3.3. Formation of polycrystalline structure.

Thermodynamical and Metallurgical Aspects of Stefan Problems

54

Fig. 2.3.4. (a) Small perturbations at the interface are growing (b) Perturbations are dying. unstable. Mushy region will develop in front of the interface. In Fig. 2.3.4. (b), the perturbations are dying and the planar interface remains planar. Figs. 2.3.5—2.3.7. show solid-liquid interface morphology and the temperature distributions in the solid and hquid regions. In Fig. 2.3.5., freezing temperature is equilibrium temperature T^. The interface is planar and perpendicular to the direction of heat flow. The hottest part of the system is the hquid region. In Fig. 2.3.6. the growth of freezing front is columnar. The hottest part of the system is liquid. This growth is more common in alloys. In Fig. 2.3.7., the grains are equiaxed and have similar dimensions along all axes. The hottest part of the system is the crystal as the liquid is supercooled. The interface is stable in Fig. 2.3.5 and unstable in Figs. 2.3.6. and 2.3.7.

+ ;I

-q" 0 D 0)

a E

/ ^

Solid ^*r-q

Liquid -«—q'

(D

Interface-^

Fig. 2.3.5. Solid-Liquid interface morphology and the temperature distribution. Planar growth.

Fig. 2.3.6. Solid-Liquid interface morphology and the temperature distribution. Columnar growth.

2.4 Non-material

Singular Surface: Generalized

Stefan

Condition

55

Fig. 2.3.7. Equiaxed dendrite growth

2.4

Non-material Singular Surface: Generalized Stefan Condition

A singular surface is a surface which does not have any inner structure so as to give rise to discontinuities in the bulk quantities. SoHd-hquid interface and shock waves are examples of singular surfaces. The motion of a singular surface could be independent of the motion of the bulk phases. A material surface is a surface which consists of the same material particles all the time. Fluid films and coatings are examples of a material surface. A surface which is not a material surface is called a 'non-material surface'. It is well known t h a t surfaces of bodies, and interfaces between pairs of bodies, exhibit properties quite different from those associated with their interiors. There have been several a t t e m p t s (cf. [46, 47, 48, 49]) at formulating the equations of conservation of mass, motion and energy in a moving singular surface embedded in a three-dimensional continuum and dividing the continuum into two regions for which the singular surface is a common boundary. Some thermodynamic fields may have discontinuities across this singular surface. In the classical Stefan condition (1.4.8), the j u m p in the normal component of the heat flux vector across the phase-change boundary is given in terms of the amount of latent heat released or absorbed at the phase-change boundary. It is assumed t h a t no mechanical work is done. The modern theory of surface thermodynamics and mechanics takes into account other aspects also such as the surface stress, in particular surface tension, and conduction of heat tangential to the surface while balancing energy along the singular surface. The Stefan condition derived below takes into account the surface tension and heat conduction while balancing energy in the phase-change boundary, and will be called generalized Stefan condition [51]. Consider a three-dimensional bounded region R which is occupied by solid and liquid

56


phases. There exists a time dependent smooth singular non-material surface F which divides R into two parts Rs and RL, R = Rs ^ RL ^ ^• Rs and RL are solid and liquid regions such that Rs H Ri is empty. The subscripts S and L stand for the solid and the liquid phases, respectively. The external surfaces of Rs and RL will be denoted by dRs and dRi, respectively (see Fig. 2.4.1.). Let (Rs)b = dRsUT and (RL)^ = dRiUT. The external surface of R is dRs U dRi U dT where the curve dV is the boundary of F. The surface F is orientable and the unit normal A^ to F points into the liquid phase. Let V be the velocity of F in the direction of TV, i.e., V = \V\N. \i may be noted that only the normal component of the velocity of the interface can be determined as in (L4.15). The tangential component of the interface motion for a massless interface cannot be derived a priori by recourse to principles of general vahdity [52]. We shah first balance the forces in R. These results will be used in balancing energy later. Conservation of forces in R fpBdv-\-

f Tnda+

f fiydl = 0.

dRsUdRL

(2.4.1)

dr

Here, B is the body force per unit mass, n is the unit normal vector pointing outwards as the exterior boundary of a region is traversed in the anticlockwise direction, r is the bulk stress tensor and f is the surface stress tensor, and /7 is the outward unit vector normal to dT which is tangential to F. dv, da and dl are elementary volume, elementary area and elementary length, respectively. We take ps = pi = P for simplicity. / 3

3

3

\

\i=l

i=l

1=1

/

( m , 712,723),

(2.4.2)

Tij, z = 1, 2, 3, J = 1,2, 3 are components of bulk stress tensor r . If it is assumed that both solid and liquid regions are in equilibrium independently of each other, the balancing of forces in the solid region gives / pBdv + / Tsfida + / TsNda = 0. Rs

dRs

(2.4.3)

r

Similarly balancing of forces in the liquid region gives / pBdv + f Tinda - / TiNda = 0. RL

ORL

(2.4.4)

r

The minus sign in the last term of (2.4.4) arises because the outward normal to the liquid region at the boundary F points in the direction opposite to TV. Adding (2.4.3) and (2.4.4) and on subtracting the sum from (2.4.1), we obtain / TLNda - / TsNda + / rudl = 0. r r dr

(2.4.5)

2.4 Non-material Singular Surface: Generalized Stefan Condition

57

Applying surface divergence theorem to the last term of (2.4.5) gives integration over r and then assuming local equilibrium, we obtain (TL - Ts)N + divrr = 0 in T.

(2.4.6)

Here, divpT is the surface divergence of r (cf. [47]). Surface stress tensor generahzes the usual notion of surface tension and is consistent with the atomistic calculations, indicating the presence of compressive surface stresses in certain crystals [47]. If f = crl, where a is a scalar valued function called surface tension and 1 is the inclusion mapping from the tangent space of F into the three-dimensional vector space [47], then (TL - Ts)N + KâN -h Vpa = 0, in T.

(2.4.7)

Here, Kc is the sum of principal curvatures of the singular surface. The surface divergence of a smooth vector field u : T -^ G, where G is the translation space of a finite-dimensional Euclidean point space, is given by divrw = trDu,

(2.4.8)

where the r.h.s. in (2.4.8) is the trace of the tangential derivative Du of u [47]. Note that u admits a unique decomposition, u = us -\- u^N, where its is a vector in a smooth tangential field and Un is a scalar in a smooth scalar field. If r is a smooth tensor field, then for any scalar field (j) divr(0r) = (p divpr -h r V r 0 .

(2.4.9)

Taking (I) = a and r = / (/ is the identity tensor) in (2.4.9), we get divr(T) =divr(o-/) = crdivr/ + Vpcr.

(2.4.10)

Using the relation divpl = divp/ = KcN, we obtain the last two terms on the r.h.s. of (2.4.7). Conservation of energy in the singular surface F In order to obtain conservation of energy in F, we shall first derive the equation of conservation of energy in R followed by equations of conservation of energy in Rs and Ri- Subtracting the sum of energy equations for Rs and RL from the energy equation for R, we get the energy equation for F. The equation of conservation of energy in R is — / pedv -\- — RS^RL

r

eda

= —

q- nda -

dRsudRi^

q • Vdl, dv

+ / ( T L - rs)N -Vda-^- j eUdl, r

dr

(2.4.11)

58

Thermodynamical

and Metallurgical

Aspects

of Stefan

Problems

where e is the specific internal energy, G is the surface energy of F per unit area, q is the heat flux vector of the bulk, q is the tangential heat conduction vector in F, {TI — TS)N-V is the work done by the body forces in F and U = —\V\N • n \s the heat lost or gained due t o geometry of Rs U RL djs N may have a non-zero component along n. Note t h a t {TL — Ts)N appears as a body force in (2.4.7) and the tangential work done by this force is zero. The angle which N makes with n is called contact angle. It is still being debated on how t o prescribe the boundary conditions a t the contact point [54]. By calculating

Fig. 2.4.1. Geometry in generalized Stefan condition. the time derivative of the first term on t h e l.h.s. of (2.4.11) by first principles, it can be proved t h a t ^

J pedv= I

p^^+Jp{es-eL)V-Nda.

(2.4.12)

RS^RL

RS^RL

It may be noted t h a t the region R is time independent but Rs and RL vary with time in R and this point should be taken care in calculating the time derivative to get the last term in (2.4.12). On balancing the energy separately in Rs and RL^ we get des / P-Kfdv

=-

dcL / P-^dv = RL

qs • nda dRs

Rs

qs ' Nda,

(2.4.13)

qi • Nda.

(2.4.14)

r

I qi' nda + ORL

r

Adding (2.4.13) and (2.4.14) and subtracting the sum from (2.4.11), we obtain j p[es - eL)\V\da^

- j eda = - jj^qi r

- qs) • Nda -

j^q-udl Jdv

+ / ( T L - Ts)N • Vda - f e\V\N - ndl. (2.4.15) r ar

2.4 Non-material Singular Surface: Generalized Stefan Condition

59

The second term and the last term on the r.h.s in (2.4.15) should be converted to a surface integral over F to obtain an equation for local energy balance in F. The conversion of the second term to the surface integral is straight forward. In [51], the contribution of the last term on the r.h.s. of (2.4.15) has been included as the third term in (2.4.16). Local balance of energy in F gives p{es - eiWl

+ ^' - ^ceV • N + d i v r | + {QL - Qs) • N - {TL-TS)N

e = ^

+ V- grade.

• V - 0, (2.4.16)

(2.4.17)

With the help of (2.4.6), the last term in (2.4.16) can be rewritten as {TL - Ts)N • y = - ( divrf) • V.

(2.4.18)

Equation (2.4.16) is called a generalized Stefan condition. Let us now briefly describe surface tension and its relation to G. The effect of surface tension or capillarity can be explained on the basis of the assumption that on the outer surface of the liquid there exists a surface layer which could be a few molecules thick and whose properties differ from those of the bulk liquid. The surface film and the liquid can be considered as two phases of the liquid in equilibrium. The atoms in the free surface of a sohd or a liquid have higher free energy than those inside because they have no neighbours and hence no cohesive bonds, on one side. Therefore, in equilibrium, a tension develops on the surface of the liquid. This tension is related to pressure by a relation of the form (2.2.12). a is often assumed to be identical to the free energy of the surface. Prom the relation (2.1.15), we get a = e-TS,

(2.4.19)

where T is the phase-change temperature and S is the entropy. The Stefan condition (1.4.8) can be easily derived as a particular case of (2.4.16). For the derivation of Gibbs-Thomson effect from (2.4.16), see [51]. Some other observations made in [51] are as follows. A simple criterion for the instability of the interface can be derived using (2.4.16). Let G' = 0, G 7^ 0, ^ = 0 and f = al where the surface tension a is constant. Under these assumptions, the relation given below can be obtained.

|y| . }''-f}'^^.

(2.4.20)

Here, / is the latent heat per unit mass (for simplicity take Cs = CL)- Consider a very small sohd growth protruding into the liquid (see Fig. 2.4.2.) at the solid-hquid interface. In this case Kc is negative and if (G — a) > 0, then \V\ is increasing. This is an ideal situation for the dendritic growth as any solid protrusion in the liquid will grow. If (G -a) < 0, then there is retardation. Ulp+Kc{e-a) -^ 0, then \V\ -> 00 and dendrites

60


will grow indicating instability of the solid-liquid interface. If lp-\- KC{E — a) -^ OO, then |17| - ^ 0 . This criterion may indicate branching or side protrusion in the dendrite. If the mean curvature is positive (see Fig. 2.4.3.) and G — a > 0, then the surface F is locally retarded and for G — cr < 0 it would be advanced. In the derivation of (2.4.6) and (2.4.16), both the sohd and liquid phases have been considered at rest. The motion of phases has been taken into account in [49] and a more general solidification theory has been presented which takes into account the coupling between thermal fields and kinematic fields. The liquid region is an ordinary Newtonian liquid and the solid phase an elastic material. The specific internal energy, specific entropy, stress tensor and the heat flux vector in the bulk are considered as functions of temperature, temperature gradient, deformation gradient and the rate of deformation gradient. In Clapeyron's equation (2.1.27), it is assumed that Gibbs free energies of hquid and solid phases (two different phases of the same substance) are the same and that the system is in thermodynamic equilibrium. This means that neither phase can grow or decrease. In [50], a new Clapeyron's equation has been derived, which holds in the presence of nonuniform fields of pressure, temperature, density and velocity, and which does not require the equality of Gibbs functions across the interface as long as their difference is a function of time only, or in particular a constant along the interface. It was shown that even in the presence of constant pressure along the interface, the interface temperature can be changed by increasing or decreasing the velocity at which the process of solidification is taking place. ////// //////////// /////////////// ' f f/ ff/ / / n / n f///////////////

//////////////////

f/ f / n / / / / / n / / f f

/////////////''/{> /////////////î //////////////^ /////////////

n //^

/ / / / / / / / / / / L

///////////////////'

//////////

ftj.

/i.

//////////A

// /ff///f f//

f ////

/f uf n /n f f////

f t //

t

/ / n f (u uf / // n / / ( / / n / f / / / // f n / n / f\ t H f/f //////////f f f n // f f / / / n / /1 i f^ ///////////////O f/////////// U/J

' ; ' / S o l i d ; ; F - ^ N ; V - " Liquid //////////J /////////// //f////////\

//////////// ////////////> u / / n f n / / (/ /y f / / / / n / n / f / / /1 / / / / / / / /

Fig. 2.4.2. Mean curvature K^ is negative

f//f

f f f f f

fi

Fig. 2.4.3. Mean curvature Kc is positive.

Chapter 3 Extended Classical Formulations of n-phase Stefan Problems with n > 1 3.1 3.1.1

One-phase Problems An extended formulation of one-dimensional one-phase problem

One-phase Stefan problems are mainly of three types. In the first type, one of the phases is considered at the melting temperature so that there is temperature gradient present only in one of the phases. Such problems could arise either in melting or solidification. Problems of the second kind are ablation problems in which a solid is melting and the liquid drains out instantaneously. In the third type, problems have to do with solidification of supercooled liquids, in which the temperature of the liquid is less than the equilibrium temperature leading to some changes in the energy balance equation at the interface. The melting problems in which the solid is superheated also belong to this class of problems. One-dimensional one-phase problems with different formulations have been studied from the perspectives of mathematical analysis and computation. Instead of giving complete formulations of problems arising in different contexts, we give here a general formulation of the one-phase problem so that in later sections other one-phase problems can be treated as particular cases of this general problem. This will avoid unnecessary repetitions of some details common in different formulations. A fairly general one-phase Stefan problem with nonlinear parabolic equation and nonlinear free boundary conditions has been discussed in [55] and is being presented here. Consider a time interval (0, £*). For each t G (0,t=,), consider the set J2(i) of functions p(r) which are continuously differentiable in [0,t), continuous in [0,t], and are such that P{T) G (bo, hi) for r G (0,^), p(0) = ^ 6i > 6 > 6o > 0. For S{T) G EiQ 61

62

Extended Classical Formulations ofn-phase Stefan Problenis with n > 1

and t G (0, t^) define the set Q(t) = {{X,T) :0< x < S{T), 0 < T < t} and let C^^^{n{t)) be the set of functions T(x, t) which are continuous in Q{t) together with their x-first derivatives. Assume that a(x, t,?/o,?/i,Po,Pi) is a positive function f o r O < j : < o o , 0 < ^ < t*, —cxD < ?/o, yi < oo, po > 0, —cxo < pi < oo. The function q(x,t,yo,yi,po,pi) is defined in the same domain as the function a, and h(x), f{t) are defined for 0 < x < 6, 0 < t < i*, respectively, and ip{x,t) is defined for x > 0, 0 < t < t^. The problem is to find a triple {t^, S{t),T{x, t)) such that

(i) 0 0 which, at time t = 0 is in a solid state. Heat input Q{x,y,z,t) > 0 is prescribed at the free boundary z = S{x,y,t) = S(t) and it will be assumed that melting starts instantaneously at ^ = 0 (this is a minor assumption, see § (3.2.2)). The melt is drained out as soon as it is formed. The problem is to find the temperature T(x, y,z,t) and the phase-change boundary which we shall denote by a short notation as 2 = S(t). The following dimensionless equations are to be satisfied. ^

= kV^T , z > S{t) , t > 0; S{0) = 0,

(3.1.13)

T(.T,2/,2,0U = /(x,?/,2); /(a:,i/,0) = l,

(3.1.14)

3.1 One-phase Problems

65 T(x,y,z,t)l=s(t)

= l,

5(0) = 0,

(3.1.15)

The melting temperature has been taken to be unity. The energy balance at 2; = S{t) is given by the equation

Qi.,y,z,t)U.s + K{l^{-j

dsV

fdSV\ dT +^^j Kj

Ip'i-

(3.1.16)

A Signorini-type boundary condition Suppose in the above ablation problem melting starts at t = ^0 > 0, (instead of ^ = 0) where ^0 is unknown. Then we have two types of boundary conditions on 2: = S{t)^ i > 0. T(x,t,5(t),t) d. Here, d is such that \(t)^'^{t)\ < d, t>0. and

x^'\xi'\

(3.2.13)

x i l xf\ i = 1,2 are continuous in D

\x^'Kx,t)\ < 0, (x,t)eD,

(3.2.14)

for some suitable /3 > 0. If the boundary conditions are of the type (3.2.9) and (3.2.10), then g^^\ z = 1, 2 have to satisfy some conditions (cf. [59]). For given q^''\ (j)^'-\ h^^\ x^^\ ^ = 1)2, and/(x,t) and /i(x,^) satisfying the conditions imposed on each of them mentioned above; find t^, T^^^(x, t),T^'^\x, t) and S{t) such that equations (3.2.1)—(3.2.8) are satisfied. In principle, the boundary conditions (3.2.7) and (3.2.8) on X = S[t) can be replaced by conditions of the form T'^^\S{t), t) = T^^\S{t), t) = Zi [dT^'^/dx, Wi[T^^\T^''\dT^^^ldx,dT^^^ldx,

dT^''^/dx, S{t), S{t),) ,

S(i), S{t)) - 0, on X = S{t).

(3.2.15) (3.2.16)

Here, Zi and Wi could be functionals and need not be pointwise functions of their arguments (cf. (3.3.33)).

68

3.2.2

Extended Classical Formulations ofn-phase Stefan Problems with n > 1

Multi-dimensional Stefan problems of classes II and III

According to the change of phase initiating along the fixed boundary of the region originally occupied by the melt, classical Stefan problems can be divided into three classes [60]. In class I problems solidification or melting starts simultaneously at all points of a fixed surface of the region under consideration. In class II problems solidification begins at a 'portion' of the fixed surface. In class III problems it begins at a 'point' of the fixed surface. Class II and class III problems essentially differ from class I problems in that solidification (melting) in them both spreads along the surface and grows towards the interior. Under suitable assumptions, class I problems can be formulated as one-dimensional problems but class II and class III problems are necessarily multidimensional. The position of the interface in Fig. 1.4.2. is shown after solidification for a long time. It could be due to solidification at a point or over a portion of dGi{t) or over whole of dGi{t). After sufficiently long time, when the spread of solidification over dGi{t) is complete, then solidification growth will be only towards the interior. In Fig. 1.4.1, even for longer times, a class II problem persists. At least in the analytical solutions and the analysis of Stefan problems, this distinction between different classes affects both procedures and solutions. A formulation of a multi-dimensional classical Stefan problem has already been given in § 1.4. Some more formulations will be discussed later. Because of their complexity, class II and III problems have not been studied widely. They can be formulated as one-phase or two-phase problems. A three-dimensional one-phase ablation problem in a semi-infinite region with melting due to a 'hot spot' was considered in [61] and a shorttime asymptotic solution was obtained. We present below a class III two-phase Stefan problem discussed in [62] in which solidification initiates at a point due to a 'cold spot'. Consider an axisymmetric cylindrical problem in which R and Z are cylindrical polar coordinates. A superheated melt at time i = 0 occupies the region Q < RQ < R < oo, \Z\ < GO. This melt is being cooled and a known flux Qs{Z,t) which is symmetric in Z is prescribed on the surface R = RQ of the cylinder. The temperature /L(-R, Z) of the melt at t = 0 is a known quantity which is taken to be a symmetric function in Z and is such that hiR, Z)

= r„ , Z =

0,R=Ro

> Tm , Z ^ 0, Ro < R < oo,

1 1 = 0 , Z = 0,il = /?o; ^ ^ 0 ,

Z = 0,R=Ro.

(3.2.17)

(3.2.18)

The solidification will start instantaneously at the point Z = 0, R = RQ and with time it will spread along the surface R = RQ and also towards the interior R > RQ oi the cylinder. The equation of the solidification front can be written as R = S{Z,t)]

\Z\ 0.

(3.2.19)

3.2 Some Extended Classical Formulations of Two-phase Problems

69

\Z\ = b{t) is the equation of the spread of sohdification along R = RQ^ and R = S{Z, t) > RQ is the growth of the sohdified layer towards the interior of the cylinder. The dimensionless formulation of the problem is as follows: In the liquid region 2a

2

^

dv

=v

d^n

1 OTL

Qj.2

dr

d^n

S(z, y ) < r < oo, 1^1 < oo, y > 0, (3.2.20)

dZ^

(3.2.21)

Tiir, z, V)\v=o = hir. z), 1 < r < oo, 1^1 < oo, dTL dr

QL{Z,V).

\Z\>B{V),

y>o.

(3.2.22)

•-PQL{Z,V),

\Z\0.

(3.2.24)

TUr, z, V)\r=sizy) = 1, \z\ < B{V),

V > 0,

(3.2.25)

Ts{r, z, V)\r=sizy) = 1, \z\ < B{V),

V > 0,

(3.2.26)

In the solid region

dTs dr

At the solid-liquid interface

1 + dz

2A ^99

dr

dr

r=S{z,V)

yg^,

\z\ < B{V),

V>0,

S{2,V)\v=o = I, B{V)\v=o = 0, 5(^,V)||,|=B(V) = 1.

(3.2.27)

(3.2.28)

The following dimensionless variables have been used in (3.2.20)—(3.2.28). z = Z/Ro, r = R/Ro, V = 2{kst/Riy''\

A = l/CsT^, P = KLIKS,

QL{Z,

a^ =

ks/h,

V) = QUz,t) • Ro/KgT^,

S{z, V) = S(Z, t)/Ro, Mr, z) = A(/f, Z ) / r „ , B{V) = b{t)/Ro.

(3.2.29)

70

Extended Classical Formulations ofn-phase Stefan Problems with n> 1

If the melt is superheated, i.e., if its temperature is greater than the melting temperature then for solidification to begin it is necessary (not sufficient), that the prescribed flux be infinite at ^ = 0. If at t = 0, / L ( 1 , 0 ) > 1, then we shall have a heat conduction problem (without phase-change) up to time t = tm > 0 such that at ^ = i^, conditions (3.2.17) and (3.2.18) are satisfied. Time can be rescaled and this instant of time can be taken as ^ = 0 with the initial temperature changed to the temperature at t = tm- A short-time analytical solution of a class II problem has been obtained in [63] in which solidification/melting starts at a portion of an edge in a plate. The prescribed flux need not be symmetrical. It is interesting to note that the growth of the free boundary for a short-time along r = 1 in the above cold spot problem could be of unusual type such as 0(t^/'') (similar results were obtained in [63]) but the growth the of free boundary along the interior is of well-known type such as of the order of t^^"^ or t or ^^/^. Although class II and III problems appear to be interesting and distinct from class I problems there are only some short-time analytical solutions to them in the literature. There is no report available on the existence, uniqueness and regularity of the solutions of these problems.

3.2.3

Classical Stefan problems with n-phases, n > 2

Some one-dimensional problems with more than two phases Classical Stefan problems with more than two phases are much more difficult to study than two-phase problems because of interactions among phases. Several types of generalizations of two-phase formulations to n-phase problems are possible. We shall report here some of the formulations studied in the literature. In principle, phase-change boundaries could be intersecting but such formulations have not be studied in detail. Some of these n-phase formulations are simple extensions of two-phase problems reported earlier in §§ 1.3 and 3.2.1. In an n-phase problem, it is difficult to prescribe the exact number of distinct phase-change boundaries without knowing the number of disjoint subregions and the physical situation. In several problems this has been taken to be (n — 1). In each phase a suitable parabolic heat equation is satisfied and at each phasechange boundary, two boundary conditions are prescribed (cf. § 1.3) The formulation of an n-phase one-dimensional problem in which the boundary conditions at the phase-change boundaries could be of type (1.3.5) and (1.3.6) has been considered in [64]. Odd and even numbered phases are identical so that there are only two different initial temperatures and two-different temperatures. The existence of a global solution to this problem which is nearly classical (the Stefan condition is satisfied in the integrated form) has been discussed in [64]. An analytical solution to a onedimensional n-phase solidification problem in the region 0 < x < oo has been discussed in [65]. At each free boundary, the temperature has a specified, constant, limiting value from each side. These limiting values may differ by a finite jump at different phase-change boundaries. Initially all the free boundaries coincide at x = 0 and the temperature takes the constant value Tm for x > 0 where Tm is the limiting value of the temperature as


71

x —> cxD. The Stefan condition is considered at the free boundaries. Densities of different phases could be different, giving rise to the movement of phases. Using local coordinates which are fixed in each phase, a similarity solution is presented. The formulation of the one-dimensional multi-phase problem reported in [21] is a little different. At time ^ = 0, an unbounded plate of thickness 2d and temperature To is dipped into a melt maintained at constant temperature Ti > TQ. It is assumed that a known constant heat flux q is maintained from within the melt to the plate and in the 'boundary layer' the temperature changes linearly in the direction normal to the surface of the plate. Let T^ be the freezing temperature of the melt and T„, the melting temperature of the plate. Depending on the magnitudes of different temperatures, the following three cases arise. Case I To < Tfc < Ti < Tn.

(3.2.30)

Since To < Tjt, crust forms on the plate till some time ô > 0 after which the crust begins to melt as the temperature at the surface of the plate rises to Tk and at the free boundary heat flux q is acting. Melting will continue till time î > to > 0 when the crust has completely melted. After that, heating of the plate without a phase-change continues. The plate cannot melt because the melting temperature T^ of the plate is greater than Ti. For 0 < t < ti, there exists a two-phase problem with only one free boundary and for t > ti the problem is that of heat conduction in the plate without phase-change. Because of the assumption of symmetry it is sufficient to consider the region 0 < a; < oo. Case II To < Tfc < T„ < Ti.

(3.2.31)

At any given time there will be only one phase-change boundary. The freezing temperature of the melt is lower than the melting temperature of the plate. First the crust forms and then the crust starts melting and when the plate attains temperature T„, the plate starts melting. Case III To 0; Ti|,=o - To, 0 < x < d,

Ko

dT2 dx

= PiliS2(t),

K:

m dx

(3.2.35)

t > 0,

(3.2.37)

=d+0

for X = S2(t), t > 0; ^2(0) = d,

(3.2.38)

ox = pshSiit),

for X = Si{t),

t > 0; 5i(0) = d.

(3.2.39)

T h e motion of the hquid due to the difference in densities has been neglected. Problems (P2) and (P3) can be formulated on the same lines as Problem ( P I ) , but the time interval t > 0 has to be divided into several ones and in each interval an appropriate problem is to be formulated. For example in Problem (P2), if the melting of the plate begins at t = to then for 0 < t < to, we have a problem of pure heat conduction in the plate and crust formation in the melt. For to < t < ti, where ti is the time at which the temperature at X = d becomes Ti^, there wiU be both melting of the plate and freezing of the melt. For t > ti, crust starts melting and melting of the plate continues or plate might have completely melted by that time. At each stage, temperature and the position of the free boundary / boundaries in the previous stage are to be ascertained. In [21] the main interest in the study of Case III is to examine the possibilities of occurrences of three cases ( P I ) , (P2) and (P3). This requires short-time {t -^ 0)


73

analytical solution of Problem (PI) which was obtained by using fundamental solutions of the heat equation for a double layer and taking the limit as t ^ 0. Both necessary and sufficient conditions for the occurrence of the case (PI) have been obtained in [21]. The solution to Problem (P3) will exist if Si{t) < d ioT t > 0 and therefore Problem (P3) does not have a solution. It has also been shown in [21] that the conditions under which both (PI) and (P2) are possible cannot coincide. A three-phase problem with two free boundaries has been discussed in [66] which is concerned with both melting and evaporation. Consider a solid occupying the region 0 < a; < a (one-dimensional problem). The boundary x = 0 is insulated and the solid is heated at x = a. First the solid melts at x = a and for some time, solid and liquid regions separated by a free boundary occupy the region 0 < x < a. With further heating, when vaporization temperature is attained at x = a, the liquid starts evaporating. There will now be two phase-change boundaries, viz., liquid-vapour and solid-hquid. If the solid is enclosed in a container, then heat transfer in the vapour is to be considered and there will be three-phases and two free boundaries. If the vapour is allowed to escape, then there are two phases and two free boundaries. Using finite-difference and finite element methods, numerical solution of this problem has been obtained out by several workers

(cf. [66]). 3.2.4

Solidification with transition t e m p e r a t u r e range

A very pure metal has a fixed melting temperature, which is also its freezing temperature. In the case of alloys or metals with impurities, melting and freezing temperatures are not the same and phase-change takes place over a temperature range. Let freezing and melting temperatures be denoted by Ti and T2, respectively. For metals with impurities, both heat and mass transfer should be considered but if the concentration of impurity is small, then only heat transfer can be considered with phase-change taking place over a temperature range Ti < T < T2. The region whose temperature lies between Ti and T2 is called a mushy region. There are two phase-change boundaries. The solid-mush boundary separates the solid region from the mushy region and the liquid-mush boundary separates the liquid region from the mushy region. In [67] an analytical solution of a one-dimensional solidification problem in cylindrical symmetry with an extended freezing temperature range has been obtained. The finite-difference numerical solution of a onedimensional solidification problem in a finite slab with an extended freezing temperature range has been presented in [68]. We present below a two-dimensional formulation of an extended freezing temperature range problem whose finite-difference numerical solution is reported in [69]. and Y are dimensionless A two-dimensional region 0 < X < 1 , —a 1

74

solid and stable liquid regions. It will be assumed that the solid-mush boundary can be expressed in the form X — i?i(y, €) and the liquid-mush boundary can be expressed in the form X — R2{Y,t). Without loss of generality it can be assumed that the solidification starts at X = 0 at time t = 0. Even if there is some delay in the starting of solidification, for example, if the solidification starts at ^ = ô > 0, then during the time 0 < t < to, there exists only a heat conduction problem without phase change whose numerical solution is generally considered to be simple and so assumed to be known by using well known methods. By redefining the time scale it can be assumed that the solidification starts at t = 0. The mathematical formulation of this three-phase problem in the dimensionless form as considered in [69] is as follows: In the solid region

^

" ""^ ( S ^ ^ 5 ^ ) ' 0 < ^ < RiiY.t). -a < y < a; i > 0,

= Fp{Y,t)oT

dx

m

Ts\xô = Tj,{Y,t); i > 0,

(3.2.40)

(3.2.41)

: 0 , 0 < X < Ri{a,t),

t>0,

(3.2.42)

= 0, 0 < X < Ri{-a,t),

t >0,

(3.2.43)

dv dTs dY In the mushy region

(3.2.44)

dY

dY

0, Ri{a,t) <X 0,

(3.2.45)

Y=a

0 , H i ( - a , t) <X < R2{-a, t), t > 0,

TM|t=o = g{X, Y) Tmi.

dX

OTL

dY

X>

(3.2.49)

R2{Y, 0),

0, ^ > 0,

0, R2{a,t) <X

(3.2.48)

(3.2.50)

0,

(3.2.51)

Y=a

STL

= 0, R2{-a,t)

dV

< X < 1, ^ > 0.

(3.2.52)

1.0,

(3.2.53)

At the solid-mush boundary X — i?i(y, ^) TS = TM =

(dR,y[jdTs

ÔTM)

,,dRi

(3.2.54)

At the liquid-mush boundary X = R2{Y^t) (3.2.55)

1 +

dR2 dY

dR2 = Xd' ' dt '

g{R2{Y,0),Y)

= Tmi

(3.2.56)

(3.2.57)

In the above formulation, di and d2 are solid fractions present at solid-mush and liquidmush boundaries, respectively; fs is the soHd fraction in the mushy region, g{X, Y) is the initial temperature/Ti, b is the length of the plate, a is the breadth of the plate/6, T is the temperature/Ti, Tmi is the temperature of the liquid-mush boundary/Ti. Other parameters are defined below. a = thermal diffusivity. ^^/6^ A = KM I Kg, P2 = KL/KSA

= plb^ / {K stmTi), (3.2.58)

76


tm is the time taken for the hquid to attain the temperature Ti ai X = 0. Densities of all the three regions have been taken to be equal and are denoted by p. The constant di in (3.2.54) is generally taken as unity. But in the case of 'eutectics' it can be taken to be less than unity. At the liquid-mush boundary, c/2 — 0. If in (3.2.56), 6/2 — 0 is taken then we have an implicit free boundary condition which is not convenient for the numerical solution. By taking d2 very small, an explicit free boundary condition can be generated. In § 3.3 some transformations to convert an implicit free boundary condition to an exphcit free boundary condition are given but this treatment may give rise to some other difficulties in the numerical schemes. Although it is not a rigorous mathematical convergence proof, a reasonably accurate solution can be obtained if the numerical results converge as ^2 is gradually decreased. The accuracy of the numerical solution can be further checked by some methods such as integral heat balance calculation (cf. [69]). The solid fraction in the mush depends on various physical parameters, such as the temperature of the mush, and the width of the mushy region. An exact mathematical expression for the solid fraction in the mush cannot be given and in its absence some approximate mathematical models are proposed. Two such models have been considered in [69] for the numerical solution of the problem. Model I

fs{x,y, t) = {d,{Tmi - TM{X, y, t)) - d2[\ - TM{X, y, t))}/(Tw - i.o). (3.2.59) Model II fs{X,Y,t)

= [d,{R2{Y,t) - X} - d2{Ri{Y,t) - X}]/{R2{Y,t)

- Ri{Y,t)}.

(3.2.60)

In the first model, fs is a linear function of the temperature of the mush and in the second model fs is a linear function of the 'width' of the mushy region. Thermodynamically, the heat extracted from the system at the fixed boundaries should be equal to the heat given out by the system during sohdification. If this balancing of heat is done in an integrated way over the whole region and over a period of time, then it is called integral heat balance verification. Integral heat balance is satisfied for model I but not for model II. In the first model we can calculate fs from the temperature (calculated temperature) of the mush and this procedure is thermodynamically consistent but in the second model corresponding to the calculated fs, the temperature is calculated in the numerical scheme and therefore integral heat balance is not satisfied.

3.3

Stefan Problems with Implicit Free Boundary Conditions

If in the place of (3.1.12), we have the condition dT dx

-0, x-=S{t)

(3.3.1)

3.3 Stefan Problems with Implicit Free Boundary Conditions

77

then velocity of the free boundary is not exphcitly prescribed. As stated earUer, free boundary conditions of the above type in which S{t) is not prescribed exphcitly are known as implicit free boundary conditions. Free boundary condition (3.1.12) is an explicit boundary condition as S{t) is prescribed in it. Our main aim in this section is to present some transformations which convert a Stefan problem with an implicit free boundary condition to a Stefan problem with an explicit free boundary condition. An extensively studied problem with an implicit free boundary condition known as oxygendiffusion problem will also be discussed later in detail.

3.3.1

Schatz transformations and implicit free boundary conditions

Problem 3.3.1. Find t^, T{x,t) and S(t) satisfying the following system of dimensionless equations T:,:,-Tt = F{x,t),

a<x
0 in the formulation. This problem will be called constrained oxygen diffusion problem or in short CODP. If the constraint c > 0 is not imposed in the formulation, then we have an unconstrained ODP or in short UODP. CODP is equivalent to solving the following equation with a suitable initial and boundary data. dc

H,[c),

~di~ Hy

(3.3.41)

is the Heaviside function. H,{c)

=

1,

o O

=

0,

c 0. The solution of CODP generally exists, is unique, and remains well behaved even for a sufficiently long time. The global behaviour of UODP is a delicate matter as a blow-up may occur in which S becomes infinite in finite time. Blow-up will be dealt with further in § 4.4. The solution T(x, t) of SSP is equal to Ct where c(x, t) is the solution of UODP but in general T(x, t) is not equal to Ct where c{x, t) is the solution of CODP. The non-consideration of the negativity set of c{x, t) in CODP deprives its solution of many interesting features which the solutions of UODP have, for example, the approach of the free boundary to a negativity set [75]. ODP in a radially symmetric domain. The existence of the solution of ODP in a cylindrical domain TQ < r < ri was considered in [76]. ODP in cylindrical symmetry can be easily formulated and this formulation is not being given here. The steady-state concentration Co(r) in cylindrical symmetry can be obtained as 2

2

2

co(r) = ^ ^ ^ - ^ I n ^ ,

(3.3.43)

84


where Vi solves the equation i z i l i _ d i n l ^ = c , ci = co(ro). 4

^

(3.3.44)

fi

Here, Ci and ro are given, ro is the inner radius of the cylinder. A unique root ri > TQ of (3.3.44) can be obtained. The existence of a global solution has been proved by extending the existence of the local-in-time solution. The proof of the results in the cylindrical geometry are not on the same lines as proofs developed for ODP given in (3.3.34)—(3.3.38). It has been proved in [76] that under suitable assumptions there exists a t^ such that S{t^) = TQ. Quasi-static two-dimensional ODP and the Hele-Shaw problem A link between quasi-static two-dimensional ODP and the Hele-Shaw problem has been discussed in [77]. Let p(x, y, t), where t is a, parameter, be the pressure in the wellposed Hele-Shaw problem in which the free boundary is blown outward. The pressure in the liquid satisfies the equation V^j9 = 0 in Q C i?^

(3.3.45)

Let dQ, the boundary of the simply connected region Q, be a free boundary. On (90, we have dp p = 0, ^ = —Vn or Vp • Vw = —1, on ^ — w{x, y),

(3.3.46)

where t = w[x^y) is the equation of the free boundary and n is the unit outward normal to the free boundary. Equation (3.3.45) can be obtained by taking V = —gradp in the equation of continuity of an incompressible fluid whose flow is considered in a narrow channel [78, 79]. Free boundary is the surface of an expanding fluid blob. The continuity of pressure at the free boundary after appropriate scahng gives p = 0. The steady-state diffusion equation for concentration and the boundary conditions at the free boundary in a two-dimensional ODP can be written as follows. V^c - 1, in Q c i?^

(3.3.47)

dc c= -— = 0 on t = w{x, y).

(3.3.48)

The Hele-Shaw problem (3.3.45)—(3.3.46) can be converted to a steady-state twodimensional COD described in (3.3.47)—(3.3.48) by using the transformation given in (6.2.25). The problem defined in (3.3.47)—(3.3.48) is generally well-posed and so is the HeleShaw problem in which the boundary blows outward [77]. However the Hele-Shaw 'suction problem' is an ill-posed problem and the quasi-static ODP has recently been found to be a very eff"ective tool for revealing some unexpected regularity properties of the free boundary in the solution of unstable Hele-Shaw suction problem [77].

Chapter 4 Stefan Problem with Supercooling: Classical Formulation and Analysis 4.1

Introduction

In §§ 2.2.2 and 2.2.3, supercooling in the melt was taken into account by redefining the equilibrium phase-change temperature with the help of Gibbs-Thomson relation and the kinetic condition. When both these effects are considered together, we shall call the resulting equilibrium temperature relation as modified Gibbs-Thorns on relation. In this case, the new equilibrium temperature denoted by Tg is given by Te(x, t) = Tm- {(JI[S]E)K,

- aa\Vr,\l[S]E .

(4.1.1)

The symbols T^, a, 5*, Kc and V^ have the same meaning as explained in the earlier sections; the parameter a is related to the microscopic relaxation time, [*§]£;= difference in the entropies per unit volume of the liquid and the solid at the equilibrium temperature. The last two terms in (4.1.1) are the correction terms arising due to the curvature and the velocity of the interface, respectively. Equation (4.2.11) deals with the units associated with (J, S and a. Has the solidification of a supercooled liquid been correctly and satisfactorily modelled by the equilibrium temperature in equation (4.1.1)? To answer this question we have to go back to the formation of solid from a supercooled liquid in the solidification process. It may be noted that (4.1.1) was discussed earlier also with the help of some thermodynamical and metallurgical considerations. A rigorous mathematical justification will be provided now. The origin of solidification of a supercooled liquid of a pure substance is not in the growth of a sharp interface separating solid and liquid phases but in the finite size effect of the interface lying between stable solid and stable liquid phases as shown in Fig. 4.1.1. In other words, it can be said that the sohdification of a supercooled liquid cannot progress without the formation of a mushy region in front of the solidification front. The mushy region contains both solid and liquid phases and solid could be present in it in 85

86

Stefan Problem with Supercooling: Classical Formulation and Analysis

the form of dendrites of different types. Therefore it is clear that any mathematical modelling of the sohdification of a supercooled liquid should take into account solid, liquid and mushy regions, i.e., the finite-size effect of the interface. Does it mean that the classical formulation of the Stefan problem with supercoohng accounted for by the Gibbs -Thomson law is not justified as there is no mushy region in the formulation? The rigorous mathematical justification of the sharp freezing front model (classical formulation) with equilibrium temperature given by (4.1.1) comes from the fact that the modified GibbsThomson relation can be obtained if appropriate hmits of the phase-field model which considers the finite width of the interface, are taken. Some phase-field models are being discussed here with this objective. What should be the starting point in the modelling of solidification of a supercooled liquid? Research workers have used different approaches giving rise to different models. The differences arose due to the incapability of some models to predict accurately some physical situations or non-accept ability of some models due to the so-called inconsistencies. The existing literature on supercooling is vast. Some selected approaches in the modelling of solidification of a supercooled liquid are being presented here. It is not possible to describe here even these selected models completely. What is presented below is a suitable compromise between length restrictions and understability of these models.

Fig. 4.1.1. Finite size of the interface

4.2

A Phase-field Model for Solidification using LandauGinzburg Free Energy Functional

If the interface in the solidification of a supercooled liquid is assumed to be of finitewidth, then the modified Gibbs-Thomson relation would imply that there is a sharp interface which is continuously progressing through the finite-width interface. This in turn suggests exploring the enthalpy formulation given below in (4.2.1) in which a phase function 0(x, t) has been introduced which is continuously varying through the finite-

4.2 A phase-field model using Landau-Ginzhurg free energy functional

87

width interface. Enthalpy H{T) (per unit volume) is defined by H{T)

-

PsCsTs + ps^-cl>. T < 0 , 0 = - 1 ,

=

[-psl/2,

=

PLCLTL + PL^-(I>. T > 0 , 0 = 1 .

PLI/21

T = 0, - ! < ( / ) < 1, (4.2.1)

Here, (/> is called a phase function or an order parameter which in the classical formulation has the value — 1 in the liquid phase and 1 in the solid phase. Some authors take 0 = 1 and 0 = 0 in liquid and solid phases, respectively, and take / in the place of 1/2. The phase function (j) defines the state of the system. The phase-change temperature has been taken to be zero. H{T) vs T has been plotted in Fig. 4.2.1. Enthalpy is a multi-valued function of temperature but the temperature is a continuous function of enthalpy. The equation for energy in terms of enthalpy is given by ^

= V\KT),

xencR',0 1 is a fixed region in space in which the phase-change process is taking place. In the phase transition problems with two distinct phases such as solid and liquid, / is a symmetric double-well function of 0 with two distinct minima, one for each phase. The last two terms in the integrand in (4.2.3)

88


can be thought of as the 'local Helmholtz free energy density' and (V(/))^ is the 'basic interaction term' arising due to the interaction of atoms with a mean field created by other atoms [81]. The minimum of -F(0) is attained at that value of 0 which satisfies the following Euler-Lagrange equation derived under the condition that either 0 is prescribed or Vcp • n = 0 on the boundary of Q.

Liquid

1 0 0

Temperature

.//

/2 Solid ^ = -].0

Fig. 4.2.1. Enthalpy vs temperature. SF(^) ••e"^'

r

J

,

-1 0

Fig. 4.2.2. Continuity of the phase function.

.-i;/W + lf(r- Tm) = 0,

(4.2.4)

Here, the dash denotes differentiation with respect to the argument. 6F/S(j) is the 'variational derivative' of 0 which can be easily calculated (cf. [82]). Equation (4.2.4) holds for an equilibrium state and 0 is a function only of x, x G fl. Note that F is a function of (f) and not of T{x,t) and so T in (4.2.3) is fixed. For a transient or a non-equilibrium process, the free energy will not be minimum but will satisfy the following relation

^¥(^'*)^-¥^^(^'*»'

(4.2.5)

where (5 > 0 is the relaxation time [83]. Equation (4.2.5) is valid for the case when (p is not conserved, i.e., the volume integral of (t>{x,t) over Q is not prescribed. The basis of (4.2.5) is the standard idea of 'non-equilibrium thermodynamics' which assumes that cp returns to equilibrium with a 'force' proportional to the extent to which it was out of equilibrium. If (p is conserved, then

dt

SF {x,t) = div MgTcid{—-((t)(x,t))

(4.2.6)

where M is a coefficient related to diffusion or an interdiffusion coefficient which may depend on (t){x,t) and on the temperature [83, 84]. The second law of thermodynamics

89

4.2 A phase-field model using Landau-Ginzburg free energy functional

requires that along the solution paths, the free energy should necessarily decrease with time, failing which the model will be 'thermodynamically inconsistent'. If F in (4.2.3) is a function of (f) alone, then the second law of thermodynamics is satisfied but not when F is a function of the temperature and 0. The time derivative of F{(f){x,t)} gives FW.,t)}

= / g { ^ ( x , * ) } f rfO = - | / ( ^ ) ^ O < 0.

(4.2.7)

In order to derive (4.2.7) take F as in (4.2.3) and proceed with the first principles to obtain the time derivative of F. In calculating dF/dt, at some stage of calculations Green's formula is to be apphed to the volume integral of V(t)-Vd^ldt and if it is assumed that on the boundary of Vl the normal derivative of 0 is zero then we get (4.2.7). The second law of thermodynamics is satisfied even if 0 is conserved, provided M grad dF/S^ is zero on the boundary of Vt. Sometimes, since the order parameter 0 alone is not sufficient to describe the local state of the system, additional fields are introduced. One such extra field is temperature. If the heat conduction is very 'fast' then it can be assumed that the material is at a uniform temperature but this assumption is not valid if heat conduction is 'slow'. A second equation for heat transport in the material should be considered along with equation (4.2.4) or (4.2.6). An example of this type of modelling is the phase-field model which consists of the following system of equations. „ , . * , , 2 V V + i ( * - *') + '-^{T-T,).

(4.2.8)

In equations (4.2.8) and (4.2.9), (j) and T are coupled but in deriving (4.2.8) no couphng between 0 and T was considered. The double-well symmetric function / with distinct minima at 0 = ibl is taken as / = (0^ — 1)^. The parameter e and a are defined as £:^âi/2, a = 8ie-

(4.2.10)

£ is a measure of the interface thickness and is of the order of 10~^ cm, a is the surface tension, S is the entropy per unit volume, k is the thermal diffusivity. The units of a, 5, a are as follows: (J : =

unit of Energy/(length)^"""^^ S :— unit of energy/{(length)'^-degree}

a:

unit of time/(length) , n = spacial dimension of Q.

=

(4.2.11)

At a deeper level of physics there are significant differences between the Stefan problem and the phase-field model in that the phase-field model incorporates the microscopic physics in an average sense and also takes into account macroscopic parameters. Stefan problem deals only with macroscopic modelling.

90


Both the equations (4.2.8) and (4.2.9) hold good throughout Q and the sharp interface separating sohd and hquid phases has been replaced by a finite-width interface. Therefore there are no boundary conditions at the interface. The region corresponding to T = 0 is now given by — 1 < 0 < 1, and (f) = 0 is the center of the interface. Initial and boundary conditions for both 0 and T are to be prescribed. For example, on the boundary dQ of 0, we may have = 0,

dn

dT

(4.2.12)

= 0,

(4.2.13)

dn or any combination of these boundary conditions. Note that for both T < 0 and T > 0, (4.2.9) is well defined and the region T = 0 is not defined by the enthalpy but is identified by the phase function 0, — 1 < 0 < 1. The phase-field equations were first formulated in [85] on the basis of the model discussed in [80]. The last term in the integral in (4.2.3) can be taken in the form of a more general expression such as —2u^G{(f)) (cf. [86]), where u is the dimensionless temperature and u={T-Tm)/{l/Cp).

(4.2.14)

Here, 7 is a microscopic parameter related to a macroscopic parameter and has the dimension of energy per unit volume, G{(t)) is an increasing function related to the entropy distribution across the interface and 1

[S]E = 2^ j G\(l))d(t>.

(4.2.15)

-1

If G{(j)) = (/> and the units of energy and temperature are suitably chosen, then [S]E = 4 units of energy per unit volume/degree,

(4.2.16)

and -2u-fG{(f)) = -2u(j).

(4.2.17)

In Fig. 4.2.3. the last term on the r.h.s. in the equation to determine 0 has been taken as 2u. By defining e and a through (4.2.10) and a in units of free energy, the last term on the r.h.s. in (4.2.8) can be obtained. The capillary length o?o is defined as (cf. [87]). d, = ol{[S]EllCp},

(4.2.18)


91

and it is easy to check that with the help of (4.2.18), (4.2.8) becomes ae'^

= s'V'+l{-') + ^^n.

(4.2.19)

Equation (4.2.19) has two length scales, viz., e and do. Note that there is only one length scale in the modified Gibbs-Thomson relation (4.1.1). Using (4.2.18), (4.1.1) can be written in terms of w as u = -doKc - adolVnl

(4.2.20)

In (4.1.1), specific heats, thermal conductivity and densities have been taken to be equal in both solid and liquid phases. This is generally done for convenience as the mathematics does not change significantly even if different thermophysical properties are taken in different phases. There are several advantages of phase-field models. A variety of phenomena ranging from motion by mean curvature to stable anisotropic crystal growth and single-needle dendrites are obtained by simply varying the parameters. Phase-field equations are amenable to numerical computations [88]. Computations involving selfinteractions of the interface do not pose difficulties in the phase-field model. The phasefield equations are guaranteed to have a smooth solution (0, T) if the initial and boundary data are sufficiently smooth (cf. [81, 89]). Rigorous mathematical analysis for obtaining Gibbs-Thomson relation by taking appropriate limits of some parameters was first presented in [81]. The 'Inner' and 'outer' expansions of the order parameter 0(a:, t) were obtained as ^ -^> 0 and by matching these expansions, it was proved that under suitable assumptions u{x) = -aoKji

-h 0 ( 0 , X e dQo.

(4.2.21)

where dQo is the center of the finite-width interface or where 0 = 0; Kc is the sum of the principal curvatures of the interface cp = 0 and CTQ is defined by the equation (To = ^ e

(4.2.22)

It was shown that (7 = aoH-0(^2).

(4.2.23)

Based on the mathematical procedure presented in [81], and by taking appropriate limits, modified Gibbs-Thomson relation was derived in [90] and the Gibbs-Thomson relation in [81]. In Figs. 4.2.3. and 4.2.4. (cf. [91, 90]), the appropriate hmits of the parameters to be taken, and the corresponding Stefan and Stefan-like problems obtained have been shown. Although the limiting cases obtained in Fig. 4.2.3. are covered in Fig. 4.2.4., the hmits are more explicitly defined in Fig. 4.2.3.

92

Stefan Problem with Supercooling: Classical Formulation and Analysis Phixfield equation

SurJaciimohinihMci

€chi.Akr,ii<M (Mfhix daman boindafia)

Scdinîmif u = 0 iritidl/CBtionbaindxj', /=0

Uohan bf mean cmciuft

U

7-»=--r |yi=Ji:[7ui;.»|

U

ScdingM u = 0 inMljcni<mbamikirj\

Fig. 4.2.3. Limits of phase-field equations I


Ph6iefiiM\niha=0

""'"''i'-^Y-^V-rj

3urja(e tension M/O imtiu CpTt+-^j=KV'T Jv-n=KVT-ttl^

ivn=K7TnL = K7'T lv-n=KVTn|^ m£{r-g=-<JKc

Fig. 4.2.4. Limits of phase-field equations II

93

94


The role of microscopic anisotropy in the macroscopic behaviour of the phase boundary was analysed in [92] using Landau-Ginzburg [80] free energy functional. The continuum limit for a lattice spin system with 'anisotropic interactions' J^ and spacing a^ leads to the following equation for the phase function 0.

^ f = |:4^g + ^(^-^V2«,

(4.2.24)

where d is the spacial dimension of the space, 6 is the relaxation time and u is defined by (4.2.14). The temperature and (p are coupled through an equation of the type (4.2.9) and î is related to Ji and a^. A modified Gibbs-Thomson law in polar coordinates (r, 6) was derived for the equilibrium temperature which has the form [S],u{r, 6) = -[a{0) + a"{e)]K - 5^0(6)1^9)

+ 0(^^).

(4.2.25)

Here, Â(^) is a measure of the thickness of the interface and a{6) is the angle dependent surface tension. In [93] the basic phase-field model was extended to physical problems in which fluid properties such as velocity, pressure and density variations were incorporated along with heat properties and a unified and consistent derivation of equations was obtained. Since many phase-field models for solidification have been proposed in the literature, the phase-field model consisting of (4.2.8) and (4.2.9) will be called Standard phase-field model or SPF model.

4.3

Some Thermodynamically Consistent Phase-field and Phase Relaxation Models of Solidification

It was assumed in (4.2.3) that the energy functional F is a function of 0 alone, and that T is a constant. If a more general energy functional of the form F{{T{x, t), 4>{x, t)} = | { / ( r , ) + ^B\V4>{x)\'}dn, n

(4.3.1)

is taken, in which B is either a positive constant or a function of T but not of 0, then F will not always decrease on the solution paths and the thermodynamical consistency condition (4.2.7) will not be satisfied. However either the SPF model can be obtained as a particular case of some thermodynamically consistent models or the modified GibbsThomson relation can be derived independently of the SPF model. Several thermodynamically consistent models have been proposed in the literature (cf. [94, 95, 96, 97, 98]). Our interest here is only in briefly indicating the derivation of some thermodynamically consistent models from which the modifled Gibbs-Thomson relation can be obtained by a rigorous limiting process.

Some Thermodynamically Consistent Phase-field and Phase Relaxation Models

95

Entropy Functional The model proposed in [97] and described below is based on an entropy functional and is on the same hnes as the model proposed earlier in [94]. The starting point of the formulation in [97] is to define an entropy functional F{(f){x,t),e{x,t)} for a subregion Qg of a closed and bounded domain Q C R^ in which the phase-change is taking place.

F=l[s-\e'mr}dQ„

(4.3.2)

Here, S{e, 0) is the entropy per unit volume, (p is the phase function as defined in § 4.2, e{x,t) is the internal energy density and £ is a constant. e{x,t) satisfies the equation e H - V f = 0 in Qg,

(4.3.3)

where q is the heat flux vector. The time derivative of F can be calculated as follows:

'^-/(i)

+ e^V'

e+

^JUr.v

dS_ de

as dcp

/{( — j

qê^Vct)

• £^V • {^V

0.

(4.3.8)

The derivation of (4.3.7) deserves some discussion. In (2.1.15), the phase function 0 has not been considered. Therefore, as suggested in [94], it will be assumed that even when the free energy density G and the entropy density S depend on the order parameter 0 and the temperature T, they are concave in T and e, respectively (though not necessarily in 0) and they still obey 'Legendre transform relation' and its inversion [99]. G{T, 0) = inf [e(^, 0) - TS{e, 0)],

(4.3.9)

and 6(5", 0) T

S{e,(t)) = inf

G{T, T

(4.3.10)

The differentiations of (4.3.10) with respect to e and 0 give the following results dS_ {e. de

1 T{e,^

(4.3.11)

dG 1 (T(e,0),0) T{eA) dct>

(4.3.12)

and dS^

where T(e, 0) is the value of T at which the infimum in (4.3.10) occurs. For those values of T where no phase-change occurs, G is differentiable, and d{G{T^ct>)/T} dT

-e/T^

(4.3.13)

The consistency condition (4.3.8) gets satisfied if ând 0 are chosen such that (4.3.14) and ^dS\

2vô

(4.3.15)

Here, 8 is the relaxation time and is a positive constant, and MT could be a positive constant or a function of temperature but not of 0. In both [94] and [97], the starting point for the derivation of phase-held equations is the same entropy functional (4.3.2) but the consistency condition dF/dt > 0 is satisfied in different ways. We describe very


97

briefly the procedure adopted in [94]. The transient equations for (p{x,t) and e{x,t) have been obtained from (4.3.2) using the same arguments which lead to (4.2.5) and (4.2.6). While e{x^t) is conserved, (p may or not be conserved. The quantities SF/dcf) and 5F/6e, which are required in deriving transient equations for (p and e can be easily calculated, see [94]. Having obtained the transient equations, the consistency condition can be established as in (4.2.7). Note that the time derivative of the entropy functional contains both SF/S(f) and SF/Se and it should be nondecreasing. The quantity {dS/d(t))e in (4.3.15) is not convenient to handle. So it should be expressed in terms of {dG/d(t))T as in (4.3.12). Integration of (4.3.13) gives G{T,ct>) = Tl-J

^-^d(

+/{)],

(4.3.16)

where /(0) is an unknown function. A suitable definition of e(T, 0) agreeing with the classical definition of enthalpy can be developed if we take e{T,4>) =

esiT)+p{4>)L{T),

] (4.3.17)

= e^T) + [p(^) - 1]L(T), J where p(0) is an arbitrary function except that p(0) = 0 and p(l) = 1. In the present model, we take (j) = 0 is the solid phase and 0 = 1 is the liquid phase. L{T) = 6^(7') — es{T). When T = Tm^ L{Tm) = Im, where Im is the latent heat of fusion per unit volume. Any of the expressions for e given in (4.3.17) can be used in (4.3.16). If the second definition in (4.3.17) is used in (4.3.16), then we obtain

G(r, 4>) = TI-I

^d^

- \pi4>) - 1]Q(T) + m

j,

(4.3.18)

where

Q{T) = / r„

2 -«s«

(4.3.19)

By differentiating (4.3.18) w.r.t. 0, we obtain, dC\ — \

=-TQiT)p'{)+Tf'{4>).

(4.3.20)

Note that ei and e^ are functions of T and not of 0. It is now a simple matter to derive the phase-field model. Substituting e and (f from (4.3.17) and (4.3.14) in the energy equation (4.3.3), we obtain eUT)+p{mT)

+ {p(4>) - 1 ] ^ ( T ) = - V • [MrV ( i ) ] .

(4.3.21)

98


If MT = KT^ and 0 = 0,1 in (4.3.21), then we get heat conduction equations in sohd and hquid phases, respectively. In order to obtain kinetic equation for 0, we substitute dS/d(l) from (4.3.12) in (4.3.15) and use (4.3.20). We obtain 6^ = Q{T)p\ct>) - f{ct>) + EV'CP .

(4.3.22)

Here, f{(p) is a double-well symmetric function with two distinct minima a,t (f) = 0 and 0 = 1 , and is taken as m

= 4>\l - 4>)\

(4.3.23)

It is not possible to determine p((/)) uniquely. The equations (4.3.21) and (4.3.22) can be presented in some more suitable dimensionalized forms (see [97]). The SPF model was obtained as a particular case of the phase-field model constructed in [95] subject to the conditions that the energy density vary linearly with the order parameter and the entropy be a non-concave function of the order parameter. Since SPF model can be obtained as a particular case of a thermodynamically consistent model, it can also be regarded as a consistent model. In [97], two phase-field models have been presented. One of them partially resembles the model in [85] and the other the model in [98]. Although SPF model cannot be obtained as a particular case of any of the models constructed in [97], it has been reported that by taking appropriate limits of the dimensionless equations derived in [97] and following the procedure discussed in [81], modified Gibbs-Thomson law can be derived. Some thermodynainically consistent phase relaxation models for supercooling The Stefan condition (1.4.11) imposed in the classical Stefan problem formulation does not arise in the phase-field models discussed above. Like an enthalpy formulation, phase-field model is also a continuum formulation, and (/> is defined as -1,

T 0. The equations of the type (4.3.24) are valid throughout Q, which is the region under consideration. As mentioned earlier, in an enthalpy formulation, T = 0 does not give the middle of the mushy region but in the phase-field model, 0 = 0, gives the middle of the finite-size interface. In (4.3.24), the sharp interface separating solid and liquid regions is given by 0 = 0 and not by T = 0. It is well known that in the case of supercooling or superheating, a mushy region develops, and the free boundary progresses through the mushy region. Therefore to obtain an equiaxed or columnar growth of the interface or the amount of supercooling or superheating, the phase function 0, should be in some ways associated with the structure of the mushy region. It should be pointed out here


99

that T = Tm {or T = 0) is not the actual temperature of the mushy region. It is an average value of the temperature. The actual situation is shown in Fig. 4.3.1. Several mathematical models based on relaxation dynamics have been constructed in the literature in terms of 0 and T, with which modified Gibbs-Thomson relation, mushy region, dendritic growth, etc. (cf. [100, 101, 102, 103]) can be described. Most of these models are based on the weak formulation which is not the emphasis in this volume. We give below a classical formulation concerned with a family of thermodynamically consistent models of phase transitions. Phase diffusion is neglected in this formulation by assuming that no interfacial energy occurs [100]. This means that the term ^^(V(/))^/2 occurring in (4.2.3) is taken to be zero. Therefore, only a rate-type constitutive law governing the evolution of 0 accounts for the phase relaxation.

Enthalpy, H(T)

Fig. 4.3.1. ab-metastable state for the solid cd-metastable state for the liquid. The internal energy density e(T, (p) can be taken as e(T,0) = /o(T) + /i(0),

(4.3.25)

where equation (4.3.25) is the generahzation of the energy equation considered in the earlier phase transition models. If Cs = CL, then the specific enthalpy (or internal energy) is given by e = Ci/T + /0, O < 0 < 1.

(4.3.26)

As Cv = {de/dT)v > 0, we should have /^(T) > 0 in (4.3.25). The dash denotes diff"erentiation with respect to the argument. If 0 = 0 represents the solid phase, and 0 = 1 represents the liquid phase, which is a more energetic phase then we should have /i(0) > 0. For the sake of convenience, let e(T,,^)=T^F^(r)+T;^Fi(,^),

(4.3.27)

100


where the functions FQ and Fi are assumed to be continuous with F((0) > 0 and T^ is the phase-change temperature which could be Tm or be different from T^. The energy balance equation has the standard form e(T, 0) H- div g^= r ; q = -k{T)VT,

(4.3.28)

where the dot denotes time derivative, r is the heat source density function and e is given by (4.3.27). To derive a constitutive equation for 0 it will be assumed that (j) is not an explicit function of the space variables which means that V0 = 0 or that no interfacial diffusion occurs which was present in (4.2.4). Therefore the constitutive relation for 0 can be assumed to be of the form 0 = /?(T,0),

(4.3.29)

where (5 is an unknown continuous function. The functions FQ, FI and [5 are unknown but not completely arbitrary. For example, if the system of equations (4.3.28) and (4.3.29) is thermodynamically consistent, then the Clausius-Duhem inequality should be satisfied, which implies that Q-VT G + ST-^ ^-—— < 0. 1^

(4.3.30)

Here, G is the free energy density which is related to entropy 5, e and T by the following relation. G(T, 4>) = inf{e(5,4>) - TS(e, 4>)}.

(4.3.31)

The time derivative of G gives 6^§T.f^l

(«,32)

Using (4.3.32) in (4.3.30), we obtain

The inequality (4.3.33) is satisfied if it is assumed that f)G

^

dC

+ 5 - 0, —/?(T, 0) < 0, k>^.

Substituting S = -dG/dT obtained.

(4.3.34)

in (4.3.31), and using (4.3.27), the following equation is

G-T—

= T'F;,{T)

+ T;^F,{>P].

(4.3.35)

It is easy to check that G{T, 4>) given by G(T,,^) = -TFo{T) + TB(^) - [T - TJF,(4>),

(4-3.36)

Some Thermodynamically Consistent Phase-field and Phase Relaxation Models satisfies (4.3.35). 5(0) is an unknown arbitrary function. (4.3.34) is satisfied if /3(T, 0) is taken as 1

101

The second condition in

dC

For the sake of simphcity g{T, 0) is taken as 5(T,,^) = F^WiV(T).

(4.3.38)

If P is continuous, and ^ > 0 and continuous, then N{T) should be continuous and N{T) > 0 for V T. Also F2 should be a monotonically increasing C^ function, i.e., ^2(0) > 0 for y (f). The constitutive equation for 0 can now be written as dC — {T,^) + N{T)F^{4>)4> = 0.

(4.3.39)

With constitutive equations (4.3.28) and (4.3.39), a thermodynamically consistent phase relaxation model is complete. By suitable choice of unknown functions FQ, F I , ^2(0) and N{T), several well known relaxation models can be derived as particular cases of this model (cf. [100]). Our interest here is only in analysing supercooling and superheating effects. As discussed earlier, when a phase is in a stable equilibrium, its free energy is minimum. Therefore, for stable solid and stable liquid phases, i.e., for 0 = 0 and (p = 1 at any fixed temperature, we have dG_

> 0 and —-

< 0,

(4.3.40)

as 0 = 0 and 0 = 1 are the end points of the interval [0,1]. If (j)e is any internal equilibrium point, i.e., 0e € (0,1), then dG

: 0.

(4.3.41)

If the mushy region is at equilibrium temperature T^, i.e., T^ = Tm then for all possible values of 0 G [0,1] there is equilibrium. From (4.3.36), at T = T^ = T^, we get G(T, 0) = -TFo(T) + TB{(t)).

(4.3.42)

From (4.3.41), dB{(l))/d(l) = 0 for 0 G [0,1]. Therefore 5(0) has a constant value in the interval [0,1]. In this case B = 7(0) = =

0, if 0 G [0,1] 00, otherwise.

(4.3.43)

102


I{(p) is called a indicator function which has no classical derivative in R, but since / is a proper lower semi-continuous function, its subdifferential dl exists. The subdifferential of the function 7(0) is defined as a e dl{(t)) if and only if a((/) - 0 > ^(0) - HO for V ^ G /?, a e R.

(4.3.44)

With the help of the above definition it is easy to check that dl = H~^ where H~^ is the inverse of the Heaviside graph Hg defined below 0, x < 0

Hg[x)

= (0,1),2; = 0, =

(4.3.45)

l,a:>0.

It is easy to obtain H~^ or dl by using (4.3.44), and we have dl{x)

=

0, x ^ [ 0 , l ] ,

=

{0}, x G ( 0 , l ) ,

=

R+, x = 1, R- a x = 0.

(4.3.46)

To avoid cp taking values outside the interval [0,1], but to preserve strict minima at the ends 0 = 0 and 0 = 1, a double well function should be added to the indicator function. Therefore 5(0) should be of the form 5(0) = /(0) + Bi(0),

(4.3.47)

where Bi{(f)) is a smooth 'double-well function' forcing B to have only two strict minima at 0 = 0 and (p = 1. Depending on the physical situation, 7(0) or Bi{(f)) could be zero or non-zero. -Bi((/>) is generally taken in the form Bi{(t)) = iy(t)^{l-(t>)\ f / > 0 .

(4.3.48)

Fi((/)) in (4.3.36) has been assumed to be nondecreasing and it should have strict minima at 0 = 0 and 0 = 1, as G possesses these two minima. Fi{(f)) satisfies these conditions if it is taken as [100] Fi(0) = -0^(3-2(/)), A > 0 .

(4.3.49)

Superheating and supercooling effects When a sohd is superheated, 0 = 0 even at those points of the region where T > TmNote that superheating or supercooling is assessed with respect to Tm and not with respect to T^. Similarly, for a supercooled liquid, 0 = 1 even when T < T^. Therefore the free energy G must exhibit minima at 0 = 0 and 0 = 1 for all temperatures T such

Some Thermodynamically Consistent Phase-Eeld and Phase Relaxation Models

103

that \T — Tm\/Tm < e where e is a sufficiently small positive number. In particular, minima exists at T = T^ also. We first consider the case T > T^. For T > T^, the last term in (4.3.36) is nonpositive if Fi((/)) is taken as in (4.3.49). li B = Bi in (4.3.36), then G has an absolute minimum at 0 = 1. Fig. 2.1.1. suggests that the solid is superheated. For T < T^, the last term in (4.3.36) is non-negative and G (with B — B\) has an absolute minimum at 0 = 0. Fig. 2.2.1. suggests that the liquid is supercooled. Let u{T) = X{T — T^)/{^T), X > ly > 0. If Bi from (4.3.48) and Fi from (4.3.49) are substituted in (4.3.36) and G is differentiated, then we get BC

— = 4uT 0, where K is the thermal conductivity. In irreversible thermodynamics.

104


q = k{T)V (l/T). N{T) is a prescribed quantity. For example, in [95], N(T) has been taken to be T. If 7(0) = 0, then (4.3.53) is a classical equation. If K{T) = /T, a constant, and if suitable assumptions are made about various functions then the existence and uniqueness of the system (4.3.52) and (4.3.53) has been proved in [100].

4.4

Solidification of Supercooled Liquid W i t h o u t Curvature Effect and Kinetic Undercooling : Analysis of the Solution

In §§ 4.2 and 4.3 some phase-field models were considered. With their help supercooling/superheating effects can be discussed if appropriate limits of parameters are taken. These models provided rigorous justification of the incorporation of the modified GibbsThomson relation in the classical formulation when curvature eff"ect and kinetic undercooling are included. Many physical situations can be modelled by suitable choices of arbitrary functions occurring in phase-field models and phase-relaxation models. In this section we want to discuss issues like: (i) existence, uniqueness and well-posedness of solutions and (ii) blow-up and regularization of Stefan problems with supercooling. It may be made clear that by 'Stefan problem with supercooling' we mean classical formulations of either solidification of a supercooled liquid or one or two-phase solidification problems with modified Gibbs-Thomson relation.

4.4.1

One-dimensional one-phase solidification of supercooled liquid (SSP)

The mathematical model of this problem has already been discussed in (3.1.8)—(3.1.12). Because of its simplicity this problem has been extensively studied. It should be remembered that neither the curvature effect nor the kinetic condition has been incorporated in this model. It was mentioned in § 3.1.2 that ODP (equations (3.3.34)—(3.3.38)) can be transformed to SSP and vice-versa and c(j;, t) and T{x, t) are related through the equation (3.3.39). We shall now consider a more general ODP and take C(J:,0) =CO(X) , 0 < 2 ; < 1,

(4.4.1)

where CQ{X) could be different from 0.5(1 — x)^. From (3.3.39), we have

co(x) = fd^JiUv)

+ l)dv ; Co(x) = To{x) + 1,

(4.4.2)

4.4 SolidiEcation of Supercooled Liquid

105

and C:r{0,t) is given by (cf. [104]) t

c,{Q,t) = c',{0)-h jg{r)dr.

(4.4.3)

0

Here, g{t) is the same as in (3.1.10). The second equation in (4.4.2) suggests that Co{x) should be sufficiently regular. For the existence and uniqueness of solutions some compatibility conditions should also be satisfied by the initial temperature and the boundary conditions. If the boundary condition (3.1.10) is replaced by the boundary condition T(0,t) = F{t), then we obtain [104] t

c(0, t) = co(0) + I F{T)dT.

(4.4.4)

0

The essential diflFerence between the classical Stefan problems concerning solidification of a hquid and the solidification of a supercooled liquid is in the sign requirements of the temperature difference {T — Tm)- The temperature of a supercooled liquid is less than Tm^ whereas in the classical Stefan problem without supercooling, the temperature of the liquid is greater than or equal to Tm- As mentioned earlier, whenever the classical solution of a Stefan problem is discussed here, it is implied that the solution satisfies some conditions of the form (i) - (iv) given in § 3.1.1. Depending on the problem under consideration appropriate changes have to be made in these conditions. A global-in-time classical solution is known to exist for the one-dimensional Stefan problem under suitable data assumptions (cf. [57, 75]). If the liquid is supercooled or if the solid is superheated, a solution may still exist for a short-time but a finite-time blow-up (explained below) may occur, which prevents continuation of the solution. Assuming that a solution of a Stefan problem with superheating/supercooling exists, some important questions to be investigated further are: (A) Can a classical solution of the problem exist for an arbitrarily long time ? (B) Does there exist a constant ^6 > 0 such that hmtî^_ S{t) = 0? Here S{t) is progressing towards x = 0. (C) Does there exist a constant tc > 0 such that S{t) > 0 for i G (0, tc] and lim,_,^ S{t) = -oo? Question (B) pertains to finite-time extinction and (C) pertains to the blow-up of a solution defined below. Fimte-time blow-up: If S{t) is the free boundary in a free boundary problem, and if at some time t = t* < oo, S{t^) > 0 and liminft._^f*_ S{t) = —oo, then it is said that a finite-time blow-up has occurred. Essential blow-up: If the solution of the free boundary problem cannot be continued beyond the blow-up time, then the blow-up is called essential. It may be pointed out

106


that blow-up is not a physically reahstic phenomenon and it indicates defects in the mathematical model of the problem. Non-essential blow-up: It may be possible to continue the solution of the free boundary problem beyond the blow-up time t = t^ with S{t^) and hm^-^t*- T{x,t) = TQ{X) as the initial data. In this case we have a non-essential blow-up. Many studies are available on the analysis of SSP. Each study contains several results. Only a few of these can be presented here. In [59], [104] and [105] the boundary condition (3.1.10) in SSP, has been replaced with the following: T,(0,i) = 0, 0 < ^ < ^ , .

(4.4.5)

Let Q be a constant defined as 1

Q = J{TQ{X) + l)dx.

(4.4.6)

0

The quantity {l-\-To{x)) in which the latent heat has been suitably scaled and taken as unity, represents the sum of the latent heat and the sensible heat. Q can be interpreted as the global energy of the supercooled liquid at ^ = 0 and should be greater than or equal to zero. Q plays an important role in analysing questions (A), (B) and (C) mentioned above. Let TQ{X) be non-positive and continuous continuous dX X = 1, then the supercooled sufficiently small time t 0, Q = 0 and Q < 0 are necessary and sufficient for global existence, finite-time extinction and blow-up, respectively. Blow-up always occurs when Q < 0 while Q = 0 is necessary for a finite-time extinction. If the constraint c > 0 is not added in ODP with initial concentration given by (4.4.1), then the free boundary in both SSP and UODP (unconstrained ODP) coincides and both will have a finite-time blow-up at a time at which the negativity set of c(x, t) reaches x = S{t). Fort e (0,t*), define N{t) = {x:0<x

< S{t), c{x, t) < 0}.

(4.4.7)

4.4 Solidification of Supercooled Liquid

107

In [104, 105], several results concerning blow-up in SSP and UODP have been reported. Some of them are given below. Proposition 4.4.2. If N{t) 7^ 0, then (i) for any ^2 ^ (î,^*), ^(^1) CC N{t2), i.e., the negativity set expands, (ii) if for some i > ti, the boundary dN{i) singular as t ^^ i,

touches the free boundary then S{t) is

(iii) the case above actually occurs. Proposition 4.4.3. A necessary and sufficient condition for an essential blow-up at the point {S{i),£) is that the point belongs to dN{i). Proposition 4.4.4. A necessary and sufficient condition for having S{t) singular at a point {S{i),i) is that the set {{x,t) : T{x,t) = —1} reaches the free boundary at such a point. Proposition 4.4.5. There are initial data such that ODP corresponding to SSP with (4.4.5) admits global solutions with limt_to *5'(^) = —00 for some ^0 > 0. The last proposition is a case of a non-essential blow-up and in [104] this case has been demonstrated with the help of an example.

4.4.2

Regularization of a blow-up in SSP by looking at C O D P

The question which will be discussed now is, 'how to stop blow-up in SSP'? This is called regularization. Note that there are methods other than the one discussed below for regularization. Let us first examine which physical quantity is responsible for the blow-up. The integral S{t)

E{x, t)= J (T(e, t) -h l)d^ = - c „

(4.4.8)

X

represents the thermal energy in the layer {x,S{t)) (cf. (3.3.39)). E{0,t) = E{0,0) = Q (cf. (4.4.6)). Here, c{x,t) is the concentration in ODP. If the mean energy E in the supercooled layer is defined as S{t)

S{t)

E{x, t) = {S(t) - x)-' I di I {T{r], t) H- l)dr], = {S{t)-x)-'c(x,t),

(4.4.9) (4.4.10)

then blow-up occurs if and only if E{x,t) is negative at some point {x,t). This implies that at the blow-up point c(x, t) < 0. Thus any regularization of SSP or UODP has

108


to prevent E{x,t) from taking negative values by shifting UODP to CODP. It seems reasonable to conjecture that this argument holds for multi-dimensional problems also (cf. [105]). The absolute minimum of E{x, t) is E{0, t) or Q. Blow-up occurs if and only if Q < 0. If (5 < 0, then it implies that the system does not have enough energy in the form of latent heat to cancel out the 'cold' of the supercooled liquid. Another way to look at the blow-up points is to look at the roots of the equation T(x, t) -hi = 0. Either the set of points {x, t) for which T{x, ^) -1- 1 = 0 is empty, or it has a positive distance from the free boundary. In the latter case, if this set reaches the free boundary at t = to then \im.t-^to S{t) = — oo (cf. [75]). For t < to, S{t) is bounded. This imphes that there is too much 'cold' too near the free boundary, and blow-up occurs because the energy cannot reach the point of blow-up by diffusion. To stop finite-time blow-up in SSP some mathematical techniques have been suggested in [104] which consist of modifying UODP to CODP provided CODP is formulated classically, with a new free boundary appearing each time c{x, t) becomes zero. We can call it 'nucleation' of new free boundaries. In this case we have always a finite-time extinction. This 'nucleation' of new free boundaries can be achieved in SSP also. Let 0 = 0, Co > 0. This implies that Ca;(0, t) = 0. There is no change in the energy of the system in this 'nucleation' but the creation of the new phase boundaries rearranges the energy fluxes in such a way that the blow-up that would occur due to the deficit of energy near x = S{t) is prevented by a counter-balancing surplus near x = 0. There are techniques such as incorporation of curvature effects and kinetic undercooling for the regularization of blow-up during solidification of a supercooled liquid. Curvature effects cannot be included in SSP as it is a one-dimensional slab problem. If the kinetic condition is also excluded in the formulation, then we have to resort to other techniques for regularization such as nucleation described above. Some of the results obtained in [105] have been extended to a two-phase problem considered in [106]. Let us assume that there is some sohd region (finite or infinite) to the right of x = S{t) in SSP whose temperature is Ti{x, t) < 0 for t > 0. The boundary and initial conditions are such that T{x,t) < 0, t > 0 is guaranteed till the solution exists. The following proposition, which is false for the one-phase SSP problem, is true for the two-phase problem. Proposition 4.4.6. If Q = 0, an essential blow-up will occur, while, for finite-time extinction Q > 0 is necessary. The above result has been proved by obtaining an integral equation for S{t).

4.4 Soliditication of Supercooled Liquid

4.4.3

109

Analysis of problems with some changes in t h e initial and boundary conditions in SSP

Let us consider the formulation (3.1.8)—(3.1.12) with the boundary condition T(0,t) = / ( t ) , 0 - 1 , To(x),^ - 1 in (1 - XQ, 1). Then SSP with (4.4.11) has at most one solution in the local sense. Proposition 4.4.9. Assume that there exists XQ > 0 such that To{x) > - 1 for x in (1 — xo, 1). Then SSP with (4.4.11) possesses a unique local-in-time classical solution. Existence can also be proved in a special case in which lim^;^!- inf To(x) > — 1. The convexity of the free boundary in SSP has been proved in [108] with no flux boundary condition imposed at x = 0, i.e., in (3.1.10), g{t) = 0. In [109] also, the convexity of the free boundary has been established but under special assumptions on To(x). The initial data considered in [108] is of the form To(x) < 0, X G [0,1]; To(l) = 0; To(x) G C'[0,1].

(4.4.14)

The main tool used in [109] in proving the results was the introduction of the function ^(x,^) = T^JT^,

(4.4.15)

and the study of its level curves and this was done in [108] also. SSP can be formulated in terms of i;(x, t) which will not be discussed here. Let M = {x : X G [0,1], To'(x) 7^ 0.}.

(4.4.16)

If To(x) ^ 0, then M is not void. Set P(x) = To(x)/To'(x), X G M. Out of the several results reported in [108], we present only one here.

(4.4.17)

no


Proposition 4.4.10. Assume that (4.4.14) is satisfied, and P{x) is non-negative and non-increasing in M. If P ( l ) > To(l), then S{t) > 0 for any t G (0, t^) and SSP with ^(^) = 0 in (3.1.10) is solvable for any arbitrary t^ > 0. Some results can be obtained for ODP also by following the approach adopted for SSP. In particular it can be proved that the free boundary in ODP with CQ{X) = 0.5(1 — x)^ is concave. See [108] for further details. In [110], SSP with (3.1.10) replaced by the prescribed temperature condition T(0, t) = f{t) has been considered. The questions (A), (B) and (C) raised earher in this section have been analysed. Several results have been obtained in terms of a quantity R{t) defined as 1 ^ * R{t) ^ _ + fxTo{x)dx + ff{T)dT. 0

(4.4.18)

0

The motivation for considering R{t) comes from the equation

(s(t))'-i ^-^-^

}

\

= / xT^{x)dx + / i(T)dT 0

0

T / xT{x, t)dx.

(4.4.19)

0

When S{t) = 0, we have R{t) — 0. Equation (4.4.19) and several other equations of this kind can be derived by using the following Green's identity (cf. [57]). y / ( i ; P ( T ) - TP%v))dxdT = J [{T^v - Tv,)dT + k-^Tvdx] , Dt

(4.4.20)

dDt

where P is the heat operator k~^Txx — Tt and P* is its adjoint operator, Dt = {{x^t) : 0 < X < S{t),0 < t < t^}. By choosing v and v^ suitably, several relations of the type (4.4.19) can be developed. Proposition 4.4.11. Assume that the solution of SSP (with temperature prescribed in the place of (3.1.10)) exists, and To{x) and f{t) satisfy the following hypotheses: (i) To{x) < 0 is an increasing function in [0,1], (ii) f{t) < 0 is a decreasing function of ^, ^ > 0. If case (C) (§ 4.4.1) occurs, then it implies R{tc) < 0 {tc is the same as defined in (C)). The following convective boundary condition at a: = 0 in SSP was considered in [111] in the place of (3.1.10). K^(0, t) = h(T(0, t) - g(t)), git) < 0, 0 < ^ < ^*. (4.4.21) ox The questions (A), (B) and (C) (§ 4.4.1) were investigated and in answering these questions, the key role is played by the quantity Qi{t) defined as Qi(0 - 1 + ^ + / ( I + l3x)To{x)dx + Jf3G{T)dT,

(4.4.22)

4.4 Solidification of Supercooled Liquid

111

where P = h/Kb is a dimensionless parameter, b has the dimension of length with which the space coordinate can be dimensionahzed to obtain the supercooled region as 0 < a: < 1 and

We present here one of the results reported in [111]. Proposition 4.4.12. If the solution of this changed SSP with (4.4.21) exists and the initial and boundary data satisfy the following conditions (i) To{x) > M{x - 1), and T(5(x) > 0 , 0 < x < l ,

0<M 1 are positive constants, was considered in [119] and local existence of the classical solution was proved under some assumptions some of which are the same as in [118].

116


A two-phase problem in —oo < a: < oo with kinetic undercoohng condition (4.5.10) has been considered in [120]. It was proved in [120] that if \g{T)\ < Me^'^' for some M > 0 and 7 E (0,1/4), then a global solution to the problem (4.5.7)—(4.5.14) exists under suitable assumptions. If g{T) > ae^^'-^' for some constant a and large 71, then blow-up in finite time may occur. A critical value of the exponent 7 was obtained in [121] as 7 = \/27re such that for 7 G (0, V27re), a global-in-time solution exists and blow-up in finite time occurs if g{T) > ae^'-^L In [122], the problem (4.5.7)—(4.5.14) was considered and a single function ip{x^t) represents both initial and boundary conditions. T(x,0-V^(x,^), {x,t)ed'Qt^,

(4.5.16)

where d'Qu = {{x,0):xe

(0,1)} U {(0, t):te

(0, t,)} U {(1, t):te

(0, t,)}.

It was proved that if g{T) G C^(i?), 0 < /? < 1, ip e W^^\Qt^), g > 3 and the following conditions are satisfied (any one out of (4.5.17) and (4.5.18)), g{T) < 0, T < mi, g{T) > 0, T > ms for some mi, ms G R, 1^(7")I < CLi\T\ + a2, ai and a2 are constants, gW.ô)

= 9W.=i) = 0,

(4.5.17) (4.5.18) (4.5.19)

then a global classical solution exists such that S{t) G C^+^/2[0, t*],_A G (0,1). VK^^'HOtJ, 0' > 1 is the Sobolev space of functions u{x,t) in the domain Qt^{Qi UQ2 x (0,t*)) with bounded norm Mw^^\Qu)

= ( / d^l' + l^-l' + l ^ - l ' + lutndxdty/^.

(4.5.20)

Replace the condition (4.5.10) in problem (4.5.7)—(4.5.14) by the following kinetic condition T'{S'{t),t)

= -eS{t),

e>0,0 0 and for some tl > 0. Either tl = +(X) or min{l - S'{tl), S'{tl)} = 0. Depending on the boundary conditions, S could be greater or less t h a n zero. By considering a sequence of problems {T^"", 5"^"}, ^n > 0, ^ = 1, 2 . . . and taking the limit £n -^ 0, the existence of a weak solution has been established in [123] and it has been shown that T{S{t),t) -^ 0 for a.a. t G (0,t*). Suppose the initial d a t a is such that for some Si G [6'o, 1] To{x){x -Si)>0,

xe

[0,1], X + Si, So.

(4.5.23)

If (4.5.23) is satisfied, then a supercooled liquid phase exists between stable solid and stable liquid phases. It has been proved in [123] t h a t the simply connected supercooled liquid region disappears in finite time, after which the solution becomes a classical one. In (4.5.23), the degree of supercooling is not prescribed. It was pointed out earlier for a onephase supercooled problem (cf. Proposition 4.4.1.) t h a t the negativity set {To{x) < — 1} is responsible for a blow-up (roughly speaking). T h e initial d a t a given below gives rise to a discontinuity in the free boundary. Let 5j^ and S'f G (ASQ, 1) be such that To{x) < - / , xe

To(x) > - / , xe

(ST,*S+),

(4.5.24)

(5-0, 5 r ) U (5+, 1),

(4.5.25)

where / is the latent heat, and / > 0. Under suitable assumptions, it has been shown in [123] t h a t the free boundary is smooth everywhere except at a point t = t < t^. At this point S{t) may have a j u m p . S{t -(- 0) — S{t — 0) > 0 will be exactly equal to the length of the interval in which T{x, i — 0) < —I. In the Neumann solution (1.3.11)—(1.3.16), the velocity of the interface (cf. (1.3.13)) is infinite at ^ = 0 which seems to be inconsistent with the assumption of local thermodynamic equihbrium at a constant freezing temperature. If the kinetic condition (4.5.26) is incorporated in (1.3.5), ps — pi and in the place of / = {/ + {Ci — Cs)Tm}, I is taken, then we get a problem considered in [123]. Let Ts{S{t),t)

= TL(S{t),t)

- -£S{t),

£>0,

S>0.

(4.5.26)

Under suitable assumptions, the existence and uniqueness of the Neumann solution with the condition (4.5.26) and other changes have been proved. It has been shown that T(x, t) G CîQi) n C°^(02) and S(t) G C°^(0, t,), where Qi{Q2) = {x>0,xS{t) > 0(< 0), 0 < t < ^=,}. S{t) > jt for t G (0,^*), where 7 is a positive constant. An analytic solution has been obtained which is validated by a numerical solution obtained

118


by a finite-difference scheme [123]. An equation for the phase-change temperature has been obtained in [124] by considering the entropy production in the interface, pressureinduced undercoohng, and viscosity-induced variations in the freezing temperature. A fairly general expression for the latent heat depending on the thermal expansion coefficient, temperature, pressure, etc., has also been obtained. In deriving phase-change temperature and latent heat expressions, non-equilibrium thermodynamical considerations have been used. Dissolution of a spherical ice ball in supercooled water has been discussed in [125]. This one-dimensional radially-symmetric spherical problem is closely related to a Stefan problem with modified Gibbs-Thomson relation. In [125], a weak solution has also been discussed. We give below only the classical formulation of the problem of dissolution of a solid ice ball of radius S{t) in a supercooled liquid. Consider the following equations.

r ( r , 0 ) = To(r) < 0, 0 < r < ro, %{0) = 0; Ti(ro, 0,

(4.5.28)

TsiS(t), t) = n{S(t),

(4.5.29)

i) = - J - ^ + / ? ^ , r = S(t), t > 0; 5(0) = 1,

^ - f ^

= - / f

onr = S(t),t>0,

(4.5.30)

Here, /3 > 0 is the relaxation parameter arising in the kinetic condition, the surface tension in (4.5.29) is taken unity and Ql = {(r,t) : 0 < r < S{t); 00,

re [0,1], t > 0,

(1, ro), i > 0.

(4.5.36) (4.5.37)

In terms of Tiir, t), the initial temperature of the liquid is Tiir.O) = - 1 / r , 1 < r < ro.

(4.5.38)

Note that the surface tension which was taken as unity in (4.5.29), is still present. As the initial temperature of the solid is greater than or equal to Tiir, 0), the ice ball with center at r = 0 may dissolve partially in the supercooled water at least for a short time. To preserve the classical one-phase Stefan problem structure, we have T(S{t),t) = 0 which requires that /? ^ 0. The key idea in the existence proof for problem (4.5.36)—(4.5.38) in which /3 = 0 is to consider a sequence of problems for /3n > 0, n == 1, 2 . . . and take the limit as /?„ - ^ 0 . This method of proof is generally employed to develop the proof for the case /? —^ 0. Under suitable assumptions about the data, a unique classical solution (T5, S^) exists with the monotonically decreasing free boundary S^. Some interesting results of [125] are the following: 1. The classical solution of the problem (4.5.27)—(4.5.30) exists and is unique for p > 0 and all time t > 0. 2. If /3 = 0 in (4.5.29), then the classical solution exists and is unique only locally in time. 3. There exists at least one weak solution for /3 = 0 with a monotone free boundary r = S{t) for all time t > 0. 4. Non-existence of the classical solution for the problem with /? = 0 for all time ^ > 0 for certain types of initial data is possible in this one-phase problem. There exists at least one point t = i oi the discontinuity of S{t) such that 0 < 5 ' ( f - 0 ) <S{i + 0), or the continuous function S{t) on a small time interval (0, t*) cannot be absolutely continuous on (£, t*) and it maps some zero-measure set of (f, t^) onto some set of Qf^ ^Qt with a strictly positive measure.

120


It turns out that the results for /^ > 0 are not the same as for P = 0. The kinetic condition acts as a regularizing factor in the dissolution of ice ball in the supercooled water whereas surface tension alone does not have the same effect. The formulation given in (4.5.27)—(4.5.30) was considered in [126] also but with some minor changes in the region under consideration and some change in the boundary condition. We shah continue with the notations used in (4.5.27)—(4.5.35) with the change that S'(O) = So < I and TQ = 1. The boundary condition at r = 1 could be any of the type given below in (4.5.39) and (4.5.40) t ( l , t ) = Q(t), t > 0 ,

df

CT(1, t) = - ^ - ( 1 , t) + T(l, t)-l,t>0. or

(4.5.39)

(4.5.40)

Both (4.5.39) and (4.5.40) are in non-dimensional form. Equation (4.5.40) is a boundary condition of the fifth kind (cf. (1.4.44)) . B(^) is the temperature of the thermostat and C is the specific heat of the thermostat. We shall call this changed problem, Problem (GP). Equation (4.5.40) models the heat exchange between the thermostat and the body. Assume that to(r) e C'[0, S-o] n C'[So, 1] n C[0,1],

(4.5.41)

and the consistency conditions

to(o) = 1, f{So) = 0, ro(i) = e(o),

(4.5.42)

are satisfied. The result stated in Proposition 4.5.2. can also be estabhshed for Problem (GP) (cf. [126]). Asymptotic stability of stationary solutions of Problem (GP) was also studied in [126] and it was shown that under suitable assumptions the problem has one or two or three stationary solutions. One of them corresponds to the case in which the solid phase has melted completely. This solution is always asymptotically stable as ^ —> +00. The other two stationary solutions have non-empty solid regions. The solution with the largest radius for the solid is stable, the other is unstable. A two-phase one-dimensional Stefan problem in the region 0 < x < 1 with a kinetic condition of the form T- = T+ = eS{t), at x = S{t),

(4.5.43)

was considered in [127]. In (4.5.43), 6 is a constant without sign restrictions. Similarly S{t) has no sign restrictions. T'^ is the temperature of the region to the right of .S'(^), and T~ is the temperature of the region on the left of S{t). There are no sign restrictions on T^ and T~ and so superheating or supercooling may exist. S{0) = SQ, 0 < 6*0 < 1. There are no sign restrictions on the initial and boundary data. The main result of this

Analysis of Supercooled Stefan Problems with Modified Gibbs-Thomson Relation

121

study is that introducing a kinetic term at the interface can prevent finite-time blow-up even if supercoohng (superheating) exists. Under suitable assumptions on the initial and boundary data, the existence of a global-in time solution has been proved using Schauder's fixed point theorem. Here global-in-time solution means that either i* = oo and 0 < S{t) < 1, t < oo, 0 < t < t^ or t^ < -hoo and limt^t^_ S{t) = 0 or 1. Uniqueness of the solution has also been proved. The solution of the classical Stefan problem can be retrieved by taking the limit £ —> 0 if correct sign restrictions are imposed on the initial and boundary data and the free boundary is assumed to be nondecreasing.

4.5.4

Multi-dimensional supercooled Stefan problems and problems with the modified Gibbs-Thomson relation

The one-phase supercooled Stefan problem in two and three dimensions without regularization by the Gibbs-Thomson condition has been studied in [128] with particular interest in the mechanism of cusp formation for interfaces that are initially smooth. The problem considered is as follows: Tt = V^T, X e n{t) C R^,t>

0,

(4.5.44)

forx G ^(0),

(4.5.45)

= 0, forx G dn{t), t > 0,

(4.5.46)

V-n = - V T • n, J: G dn{t), t > 0.

(4.5.47)

T(x,0) = To{x) 2. Let G{t) = G x {t} for \/t € [0,t^],G{t) = Gi{t) U G2{t) U S{t), where Gi{t) is the solid region, G2{t) is the liquid region and S{t) is the phase-change interface separating solid and liquid regions. Let G^* = Uo

t.,

S2{U) = 0, (5.1.11) (5.1.12)

Here, X = S2{t) is the equation of the liquid-mush boundary and t = t^ is the time at which S2{t) starts growing. »S'2(^*) = 0. The above formulation requires some elaboration. The conditions in (5.1.3) have interesting physical interpretations. For example /^ (0) = 1 implies that the temperature at X = 0 is the melting temperature. It is generally understood that if more volumetric heat is supplied, then the enthalpy ai X = 0 should rise. But this does not always happen. For example, if the last condition in (5.1.3) is not satisfied then the temperature at X = 0 for ^ > 0 first becomes less than unity. After some time dT/dt becomes greater than zero so that the temperature starts rising, and again the temperature at X = 0 becomes unity and then the third condition in (5.1.3) is satisfied. ^ = 0 has been taken as the instant of time at which this happens. In view of the boundary condition (5.1.12), we should have the second condition in (5.1.3). As mentioned earlier, the melting does not start at ^ = 0 but at ^ = ^*. This is the time at which the dimensionless enthalpy at X = 0 becomes CL/CS + A. The instant t* can be calculated by obtaining the solution of (5.1.6) subject to (5.1.7) and (5.1.8) (cf. [147]). All the temperatures have been made

132

Superheating due to Volumetric Heat Sources: The Formulation and Analysis

dimensionless by dividing them by the melting temperature Tm^^K). The dimensionless time t is obtained by dividing the real time by td, which is an appropriate time with dimensions and ^ = 0 is time at which all the conditions in (5.1.3) are satisfied for the first time. Till t = t^, there exists only sohd-mush boundary X = Si{t) but for t > t^, we have liquid-mush boundary X = S2{t) also. The assumption of the continuity of enthalpy at X = Si (t) implies CM = Cs which for the sake of simplicity has been assumed to be so in the whole of the mushy region. The condition dTs/dX = 0 at X = Si{t) in (5.1.5) can be derived independently of the assumption of continuity of the enthalpy. The energy balance at X = 'S'i(^) gives

dx\ ' / / M > 1 as X t S{t)- 0 and Hs = I diS X i S{t)+0. Since TM = 1 in the mushy region BTM/OX = 0 as X T S{t)-0. It can be easily concluded from (5.1.13) that dTs/dX > 0. In view of Ts{Si{t), t) = 1 and Ts{X, t) Si{t), dTs/dX 0, then CSS ^ WS

where Q is the constant heat source in — oo < x < oo, and (3 ^ S{0) = -KLh'{0-)/l.

(5.2.17)

By considering a one-dimensional problem in 0 < x < 1, it has been shown in [151] that if the melting temperature is space-dependent, then a mushy region can appear spontaneously even in the absence of volumetric heat sources. The following weak formulation has been considered in [152]. Ht = ({H)U + f{H),

(x, t) e (0,1) X 7J+,

(5.2.18)

138

Superheating due to Volumetric Heat Sources: The Formulation and Analysis (t>{H){0,t) = {(t>{H)Ul,t) = 0,te H{x, 0) - Ho{x), X e [0,1].

R+,

(5.2.19) (5.2.20)

Here, (p{H) can be identified with the temperature and H with the enthalpy per unit volume. /, 0 and HQ satisfy some assumptions (cf. [152]). The source term f{H) and the initial enthalpy Ho{x) are so chosen that enthalpy is increasing in x and t. Initially the region [0,1] is solid. At a; == 1 it passes to mush in time and then to hquid. Interfaces appear first between solid and mush and then between mush and liquid. These recede monotonically towards x = 0. Under suitable assumptions on (/), /, HQ it has been shown that solid-mush and liquid-mush interfaces are continuous, enthalpy is continuous across the solid-mush boundary but not across the mush-liquid interface and the mushy region disappears in finite time. In equation (5.1.13) it has been assumed that the mush is progressing on the sohd. If the solid is progressing on mush, then it cannot be proved that the enthalpy is continuous at the solid-mush boundary as the Stefan condition (5.1.13) with a positive sign on the r.h.s. is to be considered. If S changes sign at both sohd-mush and mush-liquid boundaries, then the regularity of the free boundary and of the velocity satisfying the Stefan condition has been examined in [153]. The enthalpy has been assumed to be an increasing function of x. An example has been constructed in [154] in which the velocity of the free boundary changes sign infinitely many times. Classical enthalpy formulation arises in thermal switching problems also (cf. [155, 156]). Certain materials such as some types of glasses and vanadium dioxide, change phase at relatively low temperature, such as, at 70°C. In the hquid state the electrical conductivity of such materials increases by a factor of 10"^. For such materials, in Joule heating, the heat source is given by a{H)E'^, where a is the electrical conductivity, H is the enthalpy and E is the electrical field which depends on a and some other parameters. In essence, heat source may depend on the free boundary, and the latent heat / depends on the history of the free boundary [156]. The existence of the solution to a one-dimensional classical enthalpy formulation of the thermal switching problem have been proved in [156]. The emphasis is on the solution for the solid region and the solid-mush boundary. The non-homogeneous term in the heat equation contains the free boundary due to the dependence of the heat source on it. The behaviour of mushy regions in spacial dimension, n > 1, under the action of volumetric heat source depending on, x, t, and enthalpy, has been studied in [157]. Conditions on the heat source necessary for the appearance of a mushy region inside a purely liquid or a purely solid phase have been discussed. As far as regular solutions are concerned, the behaviour of the solution at the free boundary separating a mushy region from a pure phase is related to the behaviour of the source on the free boundary. Under some Lipschitz-continuity conditions on heat sources, a mushy region can expand into a pure phase only if the heat source is non-zero and is of a suitable sign at the interface. Hence, both energy and heat flux are continuous across the interface, unlike the case when a pure phase expands into a mushy region. An example has been given in which a mushy

5.3 Blow-up and Regularization

139

region in a pure phase disappears and again reappears after some time. Both weak and classical solutions have been discussed. For some results pertaining to weak solutions of this problem, see § 11.2.1. By considering a one-dimensional two-phase classical Stefan melting problem in the region 0 < x < 1 with volumetric heat sources and writing its solution in terms of Green's functions, it was shown in [144] that there exists a region S{t) < x < S{t) + d, for some d > 0 in which the solid is superheated. This happens provided the heat source is large and the prescribed heat flux on the solid at x = 1 is small. Linear stability analysis of the classical solution of this one-dimensional two-phase Stefan problem was also carried out for two-dimensional perturbations (three-dimensional perturbations can also be considered). If the heat flux towards the free boundary from the superheated solid side is greater than from the liquid side, then this situation suggests instability. Superheating occurs generally for very pure metals. Its occurrence suggests that for such problems we should have a mathematical model different from the classical twophase formulation as in the classical two-phase model, the solid cannot be superheated. One of the ways to present the superheating of the solid is to introduce the mushy region in the formulation as done in CEF. Another way is to consider enthalpy formulation which is a weak formulation. A grain or dendrite model has been proposed in [158] to describe the microstructure of the mushy region and discuss its stabihty. The solid is considered in the form of a sequence of uniform one-dimensional grains of very small length which are part solid and part liquid in the mushy region. An explicit solution for the one-dimensional version of the model is obtained. It has different forms near the pure solid boundary, in the mush, and near the pure liquid boundary. An appropriate average of this solution for the microstructure formulation, reduces to the weak solution proposed in [145]. The simple microscopic model considered in [158] for the mushy region has been further extended in [159] by including modified Gibbs-Thomson relation that results from the curvature of the interface and the kinetic condition (the normal velocity of the interface is taken away from the liquid). The fine structure of the mush consists of regularly spaced nucleation sites (grains) in one-dimension and a lattice of squares in two-dimension. A method of multiple scales is employed and a classical formulation of the free boundary problem has been used to model the evolution of the two-phase microstructure. Then a microscopic model for the mush is obtained by an averaging procedure. Emphasis is not put on volumetric heating in [159].

5.3

Blow-up and Regularization

As mentioned earlier, a blow-up may occur during the solidification of supercooled liquid if regularization is not done. In the superheating of the solid also, in.the absence of regularization, i.e., non-inclusion of surface tension effect and/or kinetic condition at the interface or absence of mushy region in the formulation, we can raise the three questions

140

Superheating due to Volumetric Heat Sources: The Formulation and Analysis

(A), (B) and (C) (§ 4.4.1) that arose in the context of supercooUng. A heat source term of the form T^+^, a > 0, has been considered in [160] in the one-phase melting Stefan problem with the superheated solid occupying the region 0 < X < S{t), S{0) = So>0. The initial temperature of the solid is To{x) > 0, x e [0, ô], 0 is the phase-change temperature, and T{0,t) = 0, 0 < t < t^. The temperature To{x) satisfies some assumptions such as: (1) To(0) = To(5'o) = 0, (2) To,a: < 0 on (XQ^SQ) for some XQ G (0, So), (3) TQ^^^ + TQ'^^ > 0 for X G (0, So). The formulation of this problem can be easily written. Let {t^, T{x,t), S{t)) be the classical solution. The main result of [160] can be stated as follows. Proposition 5.3.1. If t^ < CXD, then one (and only one) of the following will always happen. (I) S{t) -^ Soo ^ (0, oo) ast ^ t^ and there exists only one blow-up point x* G (0, 6*00)• (II) S{t) -> -hoo as ^ T ^* and the set {T{x, t)} is bounded on {(^, x) : 0 < ^ < ^*, 0 < X < min (a, S{t)) for each a > 0. It was pointed out earher that questions (A), (B) and (C) (see § 4.4.1) can be answered for the supercooled problem (3.1.8)—(3.1.12) with the help of the quantity Q defined by (4.4.6). A superheated one-dimensional problem can be formulated on the same lines as the formulation of the supercooled problem (3.1.8)—(3.1.12) and so complete formulation will not be given here (cf. [161]). But, for the sake of clarity, it may be mentioned here that the region 0 < x < S{t), S(0) = 1, is the superheated solid and x > S{t) is the liquid region with T^ = 0 • S{t) is progressing towards x = 0. For simplicity we take dT/dx = 0 at X = 0. The quantity PQ given by Po=

/ \ T O ( X ) - 1) c^x,

(5.3.21)

plays an important role in answering the questions concerning blow-up in superheating. To(x) > 0 is the initial temperature of the sohd, 0 < x < 1, and the latent heat of fusion has been taken as unity in (5.3.21) after scahng. In melting, latent heat is negative and Po is the energy required for the complete melting of the superheated solid 0 < x < 1. If Po > 0, then rS{t)

/

{T{x,t)-l)dx

(5.3.22)

will remain positive. The statements (Al), (Bl) and (CI) given below hold. (Al) If the solution exists for all time, S{t) ^ Soo > 0 and T(x, t) ^ 0 as t ^ 00 then - JQ°° dx is negative. (Bl) If there exists some finite time t = t^ such that the solution exists for 0 < ^ < /* and as t ^ t^, S(t) -^ 0 and dS/dt ^ -00, then Po = 0. (CI) If the solution exists only for 0 < ^ < ^* but as ^ -^ t^, dS/dt -^ - 0 0 and S -^ S^ > 0 then the solution blows-up. In the supercooled problem, roughly speaking, when the free boundary touches the negativity set {T(x,t) < —1} then blow-up occurs.

5.3 Blow-up and Regularization

141

In the superheating problem, if the free boundary touches the positivity set {T(x, t) > 1} then blow-up occurs. The heat in the solid near the free boundary is too much and the advancing free boundary cannot remove the heat and bring down the temperature to the equilibrium level which is taken as zero. It is possible to give more general sufficient conditions for a blow-up. If there exists a function f{x) defined for 0 < x < S{0) such that: /(O) > 0, f (0) > 0, f'{x) > 0 for 0 < X < 5(0) and 1

f{To{x) - l)fdx > 0,

(5.3.23)

0

then blow-up occurs. The questions (A), (B) and (C) ( § 4.4.1) were discussed in [161] for a two-dimensional one-phase melting of a superheated solid also. If there exists some /(x), x £ B? with / > 0 and V V > 0 in n(0) = ô C i?^ VL{t) = Qx {t}, Q C R'^, 0 1, with a sufficiently regular boundary ^Q = Fi U r2 U Fa, 0 = rî U r^2 U 5 where Qi is the solid region, ^2 is the liquid region and S is the sharp interface separating these regions. The portion Fi of the boundary dQ is kept at temperature T = 6 > 0, heat flux is prescribed on F2 and the boundary F3 is insulated. A volumetric heat sink g{x), x e Q, per unit volume is acting in O. A steady-state will be reached if the outflow of heat through F2 is large, and g is small. The temperature T{x) in Q is defined in the following way. T{x,t)

=

Ti{x) < 0 , if x G Qi, (6.1.1)

= 0, li X e S, =

T2{x) > 0, if :r G O2.

The formulation of the steady-state problem consists of the following equations. V^T, - - ^ ,

in 0 „

2 = 1,2; 0 < c/< 00,

Ti = T2 = 0, Ki-^ = K2^] onx on on 142

e S,

(6.1.2) (6.1.3)

6.2 Degenerate Stefan Problems

143

T2\r,=b>0;

and

dT —

(6.1.4) rs

-Kr

-K,

= q if T2 > 0; ^ > 0,

dn

m dn

=

(6.1.5)

9 if Ti > 0,

r2

where, n is the unit normal vector on S pointing into the Uquid. If e = K2T^ -KiT-,

(6.1.6)

where T^ is the positive part of T, and T" is the negative part of T, then we have the following problem to be solved. \/'0 = -g

i n ^ , Îr, - = ^ ,

Bf) " ^ r2

de_ dn

0,

(6.1.7)

rs

where B = K2b > 0. The main result in [162] is concerned with the existence of a critical flux q = qc{B,g) such that: (i) {q,g) with q < qc{B,g) implies T > 0 in Q. This means that only one-phase wih be present in the steady-state, (ii) {q, g) with q > qdB, g) implies T has both negative and positive values in Q. This in turn imphes that both solid and liquid phases will be present in the steady-state. First, (6.1.7) is formulated as a variational problem. Then with the help of the properties of the solution of the variational problem, qc has been obtained. Some steadystate problems have been considered whose explicit solutions verify the theoretical results. The problem considered in [162] is a generalization of the problem in [163] in which g = 0. It has been proved in [163] that there exists a gî > 0 such that for all q > qi, we have a steady-state two-phase problem in r^, and K2b qi

• meas (r2),

(6.1.8)

tto

where a^ is some constant having dimensions of (length)"

6.2

Degenerate Stefan Problems

The term degenerate Stefan problem is used for a Stefan problem in which the mathematical nature of the differential equation or the boundary condition changes if some parameter associated with the problem varies within its admissible range of values. Some of the commonly studied degenerate Stefan problems are:

144

Steady-State and Degenerate Classical Stefan Problems

(i) Quasi steady-state Stefan problems or quasi-static Stefan problems in which the heat equation is elhptic but the free boundary is time dependent. Such problems may arise if the the specific heat C = 0 or the temperature has attained a steadystate. The Hele-Shaw problem described in (3.3.45)—(3.3.46) is a quasi steady-state degenerate Stefan problem. (ii) Parabolic-elliptic Stefan problems in which the specific heat C = C{T) is such that C{T)

= > 0, if T > 0, (6.2.9) =

0, if T = 0.

Quasi steady-state Stefan problems Using the theory of conformal mappings, a two-dimensional quasi-static moving boundary problem can be described by a non-linear Lowner-Kufarev equation [164] and a functional relation T between the shape of the free boundary and its velocity can be established. Together with the initial data this leads to an initial-value problem. Assuming that T satisfies certain conditions, the existence of a local-in-time solution of this initial value problem has been proved in [165]. This method is mainly applicable to those free boundary problems in which the domain is shrinking. Continuity conditions on !F are also not easy to satisfy. The proof is based on the convergence of Picard iterative method. In the Stefan problem considered in [166], the free boundary conditions are T = 0, and R{x)Vn = {ut, A{x,t)V:,T)]

on r(^).

(6.2.10)

Here, r(^) is the free boundary, T{t) n ^Q = 0 and dVt{t) = r{t) UdQ^^t e [0, ^*], n is the unit normal outward to r(t), Q{t) = Q x {t}, 0 0 in Q(0),

(6.2.12)

and dR/dXn < 0 in some neighbourhood Aô of r(0) in Q. Let (An(x), uj{x)) be the local coordinates in Aô, with uj{x) the local coordinates of the projection P{x) of a point X e No on r(0) and Xn(x) the distance from x to P{x). For the conditions in (6.2.12), we have a degenerate Stefan problem. If R{x) = 0 then we have the oxygen-diffusion problem in R'\ Generally the existence, uniqueness and regularity of solution of degenerate Stefan problems are discussed in the context of their weak solutions [167, 168, 169, 170, 171, 172], but the weak solutions are not sufficiently regular to be called classical solutions. In some cases the existence of the classical solutions of deg(nierate Stefan problems has been investigated which are discussed below.


145

Using Hanzawa transformation [133] so as to consider a problem in a fixed domain and an analogue of Moser-Nash theorem [173] and assuming some compatibility and other conditions, the existence of the unique solution of the degenerate problem (6.2.10)—(6.2.12) and the solution of oxygen-diffusion problem for R{x) = 0 has been estabhshed in [166] on a suflB.ciently small time scale. Degenerate parabolic-elliptic problems The parabolic-elliptic Stefan problems have been analysed mostly for their weak solutions. Only few studies have been reported on the analysis of the classical solutions of these problems. The regularity of the classical solution of the two-phase one-dimensional degenerate Stefan problem described in (6.2.13)—(6.2.17) has been discussed in [174]. Let the regions — 1 < x < S{t) and S{t) < x < 1 be denoted in the following equations by superscripts 1 and 2, respectively. p\T)Tl

- Ti, = 0, -l<x
(5 > 0 and To'^(x) x>0 and only if x = 0.

where the inequality holds if

The main result of [174] is the following proposition. Proposition 6.2.1. hold good.

Under the assumptions (Pi) and (P2), the following results

(1) If the data To'^(x) G C ^ [ T 1 , 0 ] and g^^'^{t) 6 C^lO.t^] satisfy second order compatibihty conditions, then the unique weak solution has the following regularity S{t) e C^(0,^.]; T'^^x.t)

e Cîi^l,

S{t)] x [0,^*]).

(6.2.18)

(2) If the data To'^(x) G C ° ° [ T 1 , 0 ] and g^^'^{t) G C°°[0,^*] satisfy the C°° compatibility conditions, then the unique weak solution is also C°°-smooth up to the boundaries t — 0 and X = ±1.

146

Steady-State and Degenerate Classical Stefan Problems

Definition 6.2.1. : C°°-compatibility conditions are called m-order compatible at (x, t) = (0,0) and (=Fl, 0) ifTj'^(x) e C2^[q=l,0], g^^^{t) e C^[0,^*] and there exist functions S'W ^ ^^^[O,^*] and f i'2(a;,^) G C2^'^[5(^), ^1] x [0,^*] such that f i'2(^l, t) = g^^^(t), f'^\S{t),

t) = 0,

(6.2.19)

/ > , t) = /?^'2(f i'2)f/'' - f^f - 0 ( r ) ,

(6.2.20)

5(0) - 0 , g{t) = S'{t)-t^{S{t)-0,t) + t^{Sit)+0,t) = 0(r).

(6.2.21)

If To'^(x) € C ° ° [ T 1 , 0 ] , î'2(t) e C°°[0,t,] and (6.2.19)-(6.2.21) are satisfied for any m, then the data are called C°°-compatible. A weak variational formulation of the multi-dimensional degenerate parabolic-elliptic Stefan problem has been presented in [167]. By applying the parabolic regularization technique, the existence, uniqueness and stability of the solution with respect to the data, have been analysed. Boundary control aspects have also been discussed. By considering the weak formulation of a two-phase degenerate Stefan problem, the Lipschitz continuity of the free boundary (under suitable assumptions) has been proved in [169] in some small time interval. These results have been further extended in [170] and under suitable assumptions the free boundary is Lipschitz continuous and temperatures satisfy (6.2.13) and (6.2.14) classically

6.2.1

A Quasi-static Stefan problem and its relation t o t h e Hele-Shaw problem

A one-phase quasi-static Stefan problem (QSSP) in the region Q{t) = Q x {t}, Q C jR", n > 2 can be formulated by taking the specific heat C = 0 in the heat equation in the one-phase Stefan problem. Temperature is static but the free boundary is time dependent. Let dQ{t) be the free boundary which is also the outer boundary of Q{t). Q{t) could be expanding or shrinking for ^ > 0. Shrinking region problems or suction problems, are generally ill-posed. The Hele-Shaw problem (HSP) in R'^ given in (3.3.45)-(3.3.46) can be identified with a Stefan problem if the pressure p of the fluid is regarded as the temperature of the hquid in QSSP. If p > 0, then p is the temperature of the warm liquid which is expanding on ice. If p < 0, then p is the temperature of the supercooled liquid, and ice is expanding on this supercooled hquid. The pressure of the liquid can be increased (decreased) by injecting (withdrawing) fluid though the inner fixed boundary of n(0) if Q{0) is considered to be a doubly-connected region. In this case the fluid is surrounding a region G C R^\ n > 2 and the inner static boundary of 0(0) is dG. The boundary conditions on dG could be dp -— = - Q , Q > 0 (pressure increases), on

(6.2.22)


147

dp -— =^ Q, Q > 0 (pressure decreases), on

(6.2.23)

where, n is the unit outward normal to dG. Fluid can also be injected (withdrawn) though point sources (sinks) or distributed sources (sinks) situated in 0(0). Q{t) could be a simply connected region with outer boundary as the free boundary. When sources or sinks are present, the governing differential equation will have singularities. If the two-dimensional Hele - Shaw cell has porous plates though which a uniform suction is applied, then the formulation for pressure can be written as V^p -h F{t) = 0, F > 0, X G n{t); p = 0 and dp/dn = V, on dn{t).

(6.2.24)

Here, V is the outward normal component of the velocity of the free boundary. By using the transformation p = p + F{t) [/,

(6.2.25)

where U is the solution of the problem VÛ = 1 in Q{t); f/ = 0 and dU/dn = 0 on dn{t),

(6.2.26)

this uniform suction problem can be converted to a standard Hele-Shaw problem except at the singularities of F. For a two-dimensional HSP, complex variable methods can be used to find some exact analytical solutions. For example, it has been shown in [161] and [175] that due to suction from a point sink, a limacon can become a cardioid with a cusp. For Hele-Shaw problems with shrinking regions a variety of cusp may occur. For both expanding and contracting one-phase Stefan problems, the free boundary has been shown in [176] to depend continuously and monotonically on the specific heat C taken to be greater than or equal to zero. In some cases, temperature has also continuous dependence on C (specific heat). In particular, taking C —> 0, the free boundary in the Stefan problem approaches that of the Hele-Shaw problem and it follows that even wellposed Stefan problems can have free boundaries which can get arbitrarily close to forming cusps. If the free boundary in an expanding Hele-Shaw problem has cusps as ^ -^ oo, then Stefan problem in the hmit t ^ oo, also develops cusps [177]. For n > 2, Hele-Shaw suction problem with boundary conditions (6.2.22) and (6.2.23) and one-phase supercooled water problem were discussed in [177]. Existence of weak solutions for both the problems can be proved if and only if the initial domain belongs to a certain class of domains. Uniqueness does not hold in general. In the ill-posed Heleshaw suction problem, fingering configuration can arise from a suitable initial domain whose boundary is smooth and nearly spherical. In the supercooled water problem the initial domain should belong to a certain class which depends on the initial temperature. Regularity of the free boundary has also been discussed.

Chapter 7 Elliptic and Parabolic Variational Inequalities 7.1

Introduction

Rigorous definitions of elliptic and parabolic variational inequalities will be given a little later. Before that we ask a question, What are the essential features of a variational inequality formulation? Let us consider a simple problem of finding the point XQ G (a, b) at which the unique minimum of a real valued function f{x) G C^[a, b] exists. If f{x) is a convex function, then XQ can be obtained by solving the equation f'{xo) = 0. In general for XQ G [a, 6], three cases arise: 1. If minimum is attained at XQ = a, then f'{xo) > 0. 2. If minimum is attained at XQ = b, then f'{xo) < 0. 3. If xo is an interior point, then f'{xo) = 0. These three conditions can be expressed in terms of a single inequality f{xo){x - xo) > 0, V X G [a, b].

(7.1.1)

Equation (7.1.1) is an example of a variational inequality whose characteristic features are that it is an inequality and it is satisfied for all x varying over the interval [a, b]. We shall now generalize this notion and consider a space of functions, say, H^{Q), Q C K^, n > 1 is an open bounded set and let / be a functional on //^(Q). Find a function u = UQ e H^{Q) or belonging to a subset of H^(Q) such that f{uo) is minimum as u varies over H^{Q) or over a subset of H^{Q). Immediately several questions arise such as: What sort of function spaces should be considered so that a solution can be found? What should be the form of the functional defined on these spaces? Are there equivalent formulations? Answers to these require sophisticated functional analysis tools 148

7.2. Elliptic Variational Inequality

149

whose detailed description is beyond the scope of this book. In the next few sections an attempt will be made to answer some of the above questions in simple mathematical terms. After discussing the theoretical background of ehiptic and parabolic variational inequalities, the formulations of some classical Stefan problems as variational inequalities have been given. It may be noted that for any given classical Stefan problem it may not be possible to formulate it as a variational inequality problem. Weak formulations of Stefan problems, which are continuum models, are easily amenable to variational inequality formulations as variational inequalities are themselves continuum models but this is not the case with classical formulations. To make this volume self-contained, some relevant definitions and theorems are given in the Appendices A—D. The elliptic variational inequalities will be discussed first. Whenever it is possible to formulate transient Stefan problems as variational inequalities, they are formulated as parabolic variational inequalities. Elliptic variational inequalities, which are concerned with elliptic or steady-state free boundary problems, serve as a good starting point for discussing parabolic variational inequalities. This is because many of the ideas involved and approaches used in proving results in the analysis of elliptic variational inequalities can be extended, with appropriate changes, to the analysis of parabolic variational inequalities. This does not mean that every elhptic problem can be extended to a time dependent parabolic problem.

7.2

The Elliptic Variational Inequality

7.2.1

Definition and the basic function spaces

Let r^ be a bounded open subset of R^ with smooth boundary dQ. An inequality of the form a{u,v -u)

> {q,v-u),

\/ v ^ M; u e M,

(7.2.1)

where a{u,v) is a quadratic bilinear form (cf. Appendix A), a{u,v) : H^(Q) xH^{Q) -^ i?, and (q,v) = [ qvdx, q G LÎQ),

M = {ve H\Q); v-de

Hîn); v>^,

(7.2.2)

ê

C{(1)] ,

(7.2.3)

is an example of an elliptic variational inequality, q, d and ip, are known functions. V — d on dVt is the trace sense. 0 is called an obstacle and the problem is called an obstacle problem or an elliptic variational inequality with obstacle. If there exists a function UQ E M which satisfies (7.2.1) for ah v G M, then WQ is called a solution of the elliptic variational inequality. It can be proved that A1 is a non-empty closed convex set (cf. § 7.2.4 for the proof). Problems with more than one obstacle can also be studied

150

Elliptic and Parabolic Variational Inequalities

(cf. [178]) but such problems will not be discussed here. It is well known in the calculus of variations that the problem formulated in a proposed class of functions may not possess a solution in that class. This difficulty can be overcome by broadening the class of functions in which the problem is formulated and therefore the admissible functions are considered in 'Sobolev spaces' or the 'space of distributions'. A 'Hilbert space' H^{Q) has been considered in (7.2.1) as we would like that at least the first order weak derivatives of functions belonging to M exist. The choice of an appropriate Sobolev space depends on the physical problem under consideration. For example, if in a given physical problem, a solution of the form y = \x\, x e R, makes sense then H^{R) is an appropriate space for the admissible functions. Several other questions concerning variational formulations arise which will be explained after an adequate mathematical exposition of the concepts and notions of variational inequalities. Let A : H^{Q) -^ H~^{Q) ( H~^ is the dual space of the Hilbert space i / \ i.e., the space of continuous hnear real valued functions on H^{Q)) be an operator such that for a fixed lA G H^{Q), Au{v) = a{u,v), v G H^{n). A^ defines the mapping!' -^ a(u^v). It can be easily proved that Au is linear and if a{u,v) is continuous, i.e., |a(w,i;)| < M||tx||||f || for some M e R then \\Au\\H-Hn)=

sup \Au{v)\ < M\\u\\ IHIH=I

(7.2.4) ^ ^

and hence Mll£(//i,//-i) ^ ^ 1 (constant).

(7.2.5)

Therefore, A is continuous and belongs to H~^{Q) as A is a linear continuous real valued function on H^{Q.). By Riesz representation theorem^ we have H-HnMu,v)HHn) = {u\v),

V i; e H\n),

(7.2.6)

where u* is some fixed element of H^{Q,) and depends on AuConversely, if A is hnear and satisfies (7.2.4), then a{u,v) is a continuous bilinear form. It is clear that a{u,v) = //-i(o)(^n,'?^)//i(Q)-

(7.2.7)

With each q € I/^(n), we can associate a continuous linear functional Bg G H~^{Q) which is defined as Bq:v^{q,v)=

f qvdx, v G H\n).

(7.2.8)

For a rigorous proof of this statement see [22]. A sketchy proof can be given using the following arguments. With each q G L'î^), an element of the dual space of L'^{Q) can be associated. If the dual space of L'^{Q) is denoted by L^*(Q) then L^*(Q) •—> H~^{i'}) . In view of these arguments, we can write LHn){q.v)Hîn) = H-^{Q){Bg,v)H^^n) = J qvdx = {q,v), v G H\n).

(7.2.9)


151

The pairing {q,v) is the value of the functional Bg at v in the sense of (7.2.9). We shall not justify at other places the use of {q^v) in the place of (q^v)). The above discussion suggests that a true variational inequality (or equality) in the context of (7.2.1) should be of the form a{u,v-u)

= H-Hn){û^^-u)H^^Q)

> H-^n)

{q^y~u)H^n)^

yveH\n),

ueH\Q).

(7.2.10)

The space //^, k > I can also be considered and weaker or stronger conditions can also be imposed on the functions involved in the variational inequality formulation. The form of a(u, v) depends on the elliptic operator considered in a given physical problem. For example, if the elhptic operator A : H^{Q) -^ H~^{Q) is defined as Au = V\

ueH\Q),

(7.2.11)

then aiu.v) = ,f Vu- Vvdx. a{u,v) Jn

(7.2.12)

If the elliptic operator A is defined as ^2^

^

Au=-Y,a^J{x)^ ~y

,

n

^^

+ Yl ^ ^ ( ^ ) ^ - + e(x)w, X G 0,

OXiOXj

~l

(7.2.13)

OXi

then the bilinear form in (7.2.1) is defined by the relation

^x^ dxj

^

\

^

dxj / dxi

The relationship between an elliptic operator and the bilinear form which occurs in the inequality will be discussed later (cf. (7.2.24) and (7.2.37)). The coefficients a^j, 6^ and e in the elliptic operator in (7.2.13) should belong to appropriate function spaces so that the variational inequality formulation makes sense. We shall see later that for the existence and uniqueness of solutions, it will be required that a{u,v) satisfies some conditions such as continuity, coercivity and these conditions also put some restrictions on the coefficients in the elliptic operator. The non-homogeneous Dirichlet problem corresponding to the elliptic operator A in (7.2.13) can be stated as the problem of finding a function u{x), x ^Q. such that Au = q, mQ]

u = d, on dVi.

(7.2.15)

If continuous derivatives of u exist in Q and d is continuous, then (7.2.15) is satisfied in the classical sense or pointwise sense. If q is square integrable in H, then Au = q is satisfied in the sense of distributions. If only the weak derivatives of u exist, then Au = q is satisfied in the distributional sense and u = d is satisfied on d^ in the trace sense.

152


7.2.2

Minimization of a functional

A minimization problem and its equivalent elliptic variational inequality The variational inequality (7.2.1) can be expressed in some other forms also. We shall first show that the variational inequality problem (z, v-z)-]-

a{z, V- z)>{q,v-

z), \/ v E M\

z E M\

q e L^{n),

(7.2.16)

where A^* is a convex set of an inner product space and Q is as in (7.2.1), is equivalent to the problem of minimization of a functional P{v), where P{v) = {v, v) + a{v, v) - 2{q, v), v G M*, q G L^Q).

(7.2.17)

Let a{u,v) be symmetric and 2: be a solution of (7.2.16). By definition a{u,v) is linear in both the arguments but it need not be symmetric. We shall show that P(z) < P{v), \/ v e M* so that z is the minimum of P{v). P(v) - P{z) = {v, v) - (z, z) + a{v, v) - a{z, z) - 2{q, v) + 2{q, z) + 2(z, V ~ z)^ a(v, v) - a{z, z) - 2{q, v - z).

= {z-v,z-v)

(7.2.18)

Also a{u, u) = a{u — w,u — w) — a{uj, w) + 2a{u, w).

(7.2.19)

Take u = z and w = z — v in (7.2.19). It can be seen that a{v, v) - a{z, z) > 2a{z, v - z).

(7.2.20)

On using (7.2.20) in (7.2.18), we get P{v) - P{z) >{z-v,z-v)

+ 2(2, V- z)^ 2a{z, v - z) - 2(q, v - z).

(7.2.21)

If (7.2.16) holds, then from (7.2.21), P(v) > P(z), V t; G M*. To prove the converse, suppose that P{z) < P{v), V z; G A^*. Since A4* is a convex set, if V G M* and z G M* then (1 - a)z + av G M*, 0 < a < 1. Therefore, P{z + a{v - z)) - P(z) > 0 , or a(v ~z,v -z) + aa(v -z,v

-z) +2{{z,v 'z)-â{z/u

-z)-{q,v

For (7.2.22) to hold for an arbitrarily small a, (7.2.16) should hold.

-z)} >0. (7.2.22)


7.2.3

153

The complementarity problem

By considering the minimization of the functional (a real valued function) f{v) = a{v,v)-{q,v),

(7.2.23)

we shall now obtain other forms of elliptic variational inequalities. Although a{u, v) given in (7.2.14) can also be considered, a simple bilinear form given by a{u, v)=

fVu'Vv

dx,

(7.2.24)

Q

will be considered for illustration. It will be assumed that a minimizing function u{x) exists such that f{u) < f{v), \fveM,

ueM,

(7.2.25)

where the set M is defined by (7.2.3). Since M is a, convex set, for 0 < a < 1, we have f{u 4- a{v - u)) - f{u) > 0, V ^ e X ,

(7.2.26)

or / {V(ti + a{v — u)) ' V{u + a{v — u)) — Vu • Vu}dx — n 2p{u + a{v - u)) + 2p{u) > 0.

(7.2.27)

Here, p is a continuous linear functional on H^{n) and is defined by

p{v) = I qvdx.

(7.2.28)

On using the hnearity of both p and the gradient operator, from (7.2.27) we obtain a^j V{v - u) • V[v - u)dx + aj {Vu • V{v - u) - q{v - u)}dx > 0.

(7.2.29)

For (7.2.29) to hold for an arbitrarily small a, we should have [{Vu • V{v -u)n

q{v - u)}dx > 0.

(7.2.30)

If it is assumed that u G H'^(Cl) Pi C{Q), the first term in (7.2.30) can be integrated by parts (application of Green's formula). Since v satisfies the same boundary conditions as u, we have v — u — 0 on dQ. On using this condition on d^ and doing the integration by parts, we obtain [{Vhi + q){v - u)dx 0, C e C^{^)- liu>jp, then v > ip. Substituting ( = {v - u) in (7.2.31) and remembering that C > 0 and ( G C ^ ( 0 ) , we conclude that V'û + ^ < 0, a.e. in Q, u> ip.

(7.2.32)

Next, consider a subset Qi of 0, where ni = {xe ft; u{x) > ^{x)} , Qi C Q.

(7.2.33)

If u{x) and ip{x) both are continuous in Q, then for every x G Qi there exists a neighbourhood of X in which u{x) — ip{x) > 0. Therefore Qi cannot be a closed set. For any C G Co°(ni), V = u — ^C is in TM provided | ^ | is sufficiently small. On substituting V = u — e( m (7.2 31), we get + q)C dx < 0.

-e f{V\

(7.2.34)

Q

If (7.2.34) holds for £ positive or negative and C is arbitrary, then it can be easily concluded that V\

+ q = 0, a.e. in ^ i , u>2p.

(7.2.35)

The set Qi in which u{x) > ip{x) is called a non-coincidence set and the set ^2= {x £ ft : u{x) = ip{x)} is called a coincidence set. The boundary of the non-coincidence set is called a free boundary. If F is the free boundary, then r^dftiH n.

(7.2.36)

On combining the results obtained in (7.2.32) and (7.2.35), we get the following variational inequality problem. Find u e H'^{Q) H C(0) such that Vû + g < 0, > a.e. in Q,

(7.2.37)

{Vû + q){u - ![;) = 0, J u-de

H^{ft).

The boundary condition u = d is satisfied on dft in the trace sense. The free boundary problem to be studied in Qi is to find a pair (w, F) such that V \ + ^ - 0 , inî,

(7.2.38)

u =ir, 1 ^ = 1 ^ , l0.

(7.2.44)

If a more general form of a{u,v) is considered such as the one considered in (7.2.14), then by following the procedure indicated in (7.2.26)—(7.2.35), one can easily obtain the complementarity problem of the form (7.2.37) in which in the place of S/û we shall have Au given in (7.2.13). The variational inequality (7.2.37) can be transformed into an inequality of the form (7.2.1). Let C G C ^ ( n ) , C > 0 and li be the solution of (7.2.37). Uv = u + C, then v > ip and V belongs to M. Multiplying the first equation in (7.2.37) by C and integrating over 0, we get f{S/û + q)C ip then the obstacle problem for (7.2.97) —(7.2.98) can be formulated as a variational inequality of the form (see the derivation of the complementarity problem in (7.2.37) obtained from the minimization problem) given below in (7.2.99). a{w, C-uj)>

{qX-uj),\f

Ce H^{Q),

w G //d(^),

(7.2.99)

\f w, C ^ ^ o ( ^ ) -

(7.2.100)

where a(wX)=

fVw.VCdx n

+ xfwCdx, n

It can be proved t h a t if A > —1//?, where P is the same as in the Poincare's inequality (7.2.90) then a{wX) is coercive on H^{Q.) (cf. [22]). If the boundary condition is of the Neumann type such as - ^ = r, a.e. on dQ, r G L^(Q),

(7.2.101)

where ft is the unit outward normal to dVt, then the obstacle problem results in a variational inequality of the form a{u,v-u)

> f q{v-u)dx+

f r{v - u)dx,

V i; G H\n),

ue

H\n).

(7.2.102)

In this case a{u, v) has the same form as in (7.2.100) but u,v e H\n) (boundary condition is different). By choosing A > 0 and z/ = m i n ( l , A ) , it can be shown that (cf.

[22]) a{v,v)>u\\v\\l,^,,^,

(7.2.103)

where the norm in //^(Q) is defined by (7.2.86). Note that the Neumann boundary condition (7.2.101) has already been incorporated in (7.2.102). The test function need

166


not satisfy the Neumann boundary condition as it occurs naturally in the inequality. When — V^w -^ Xu < q is multiplied by {v — u) and integrated over Q and integration by parts is done we get (7.2.102). The integration by parts will give an integral over dQ, and the Neumann boundary condition is incorporated. If A = 0, the form a{u, v) is not coercive, and in this case the problem with Neumann condition does not always have a solution; and when it does, it is not unique. The boundary conditions could be of mixed type, for example, let dQ = dQi U aOs, aî 0 ^ ^ 2 = 0 and - V ^ u + A = ^, a.e. inQ,

(7.2.104)

u = d, a.e. on 5^1, (7.2.105) Ou — = r, a.e. on aOa. (7.2.106) on Then the variational inequality formulation is still given by (7.2.102) with dfl in the integral on the r.h.s. of (7.2.101) replaced by ^^2- Since a{u,v) remains unchanged, in this case also, (7.2.103) holds good and a{u,v) is coercive. The test functions have to satisfy the boundary condition (7.2.105). Operators such as the one considered in (7.2.13) or even more general operators can be considered and the existence and uniqueness of solutions of the variational inequalities so obtained can be discussed under suitable assumptions (cf. [22]). It is not always possible to formulate a given physical problem as a variational inequality problem or obtain a variational equation for the problem. Regularity of the solution is an important aspect of the study of variational inequalities. Some results on the regularity of solutions will be given in the context of parabolic variational inequalities. With the help of the obstacle problem of the string discussed earlier in Problem 1.1.12., some other aspects of variational inequalities such as the choice of appropriate spaces in which the solutions are sought, and the restrictions on the obstacle so that the set A^ in (7.2.3) is non-empty, will be discussed in the next section. In general the space of unknown functions should be large enough so that the existence of solutions can be discussed, but small enough so that a unique solution can be obtained. In physical problems, smoothness of solutions cannot be ignored. In principle, the data spaces should be general so as to accommodate various types of data but the continuous dependence of the solution on the data is required for well-posedness.

7.2.5

Equivalence of different inequality formulations of an obstacle problem of the string

We restate briefly an obstacle problem of the string as a problem of finding a continuous function v(x) which minimizes the energy functional f{v), where f(v) = ^J^{v'fdx,

v€M2,

(7.2.107)


M2

=

{ve

=

{veH^{0,b):

167

H\0,b):v{0)

= v{b) = 0,

v{x)>i;{x),y

V{X)>IIJ{X),\/xe{0,b)}

xe{0,b)}

(7.2.108)

Since we are dealing with a physical problem, v and tp should be continuous functions. It is clear from Fig. 7.2.1. that the first order derivatives of v{x) and ip{x) need not be continuous but they should belong to L'^{ft) which is also suggested by the integral in (7.2.107).

Fig. 7.2.1. Differentiability of i;(a:) is not required.

Fig. 7.2.2. The set M2 is empty.

In Fig. 7.2.2., although v{x) > il){x)^ v does not satisfy the boundary conditions and so the set AI2 is empty. For M2 to be non-empty, 1/; must satisfy one of the following two conditions. (V^l) : 7/; G C^(n), t/;(0-|-) < 0 and i/;(6-) < 0.

(7.2.109)

(V^2) : il) e H\n),

(7.2.110)

V^(0) < 0 and t/;(6) < 0.

Note that by increasing the smoothness of -0, the smoothness of the solution is not increased. For example, if tp is taken as a parabola then ip G C°°(Q), fl = (0,6), but still the second derivative of the solution u" ^ C^(0, 6) if the parabola does not pass through the points 0 and b. In showing the equivalence of different forms of variational inequality formulations given below for the obstacle problem, the treatment is not strictly rigorous. A rigorous treatment would require that the condition u" < 0 is considered in the sense of distributions in the formulation (I) given below. If w G i/^(0,6), then it is not necessary that u" belongs to L^(0,6). It will be assumed for the present discussion that u,v e //^(n)nC(Q) and u" belongs to L^(Q). The obstacle ip satisfies one of the two conditions (-01) or ('02). For clarity, the three different formulations are restated below. (I) Find ue M2 {M2 as in (7.2.108)) such that u{0) {u - 'ip)u" = 0.

u{b) = 0, w'' < 0, 16 > 0 and

168


(II) Find u such that b

I u\x){v'{x)

- u'{x))dx > 0, ^ ve M2, u e M2.

(7.2.111)

0

(III) Minimize j{dvldxfdx,

\J

v^M2.

If u',v' e L^n), then u'^ and u'v' G L^Q). Further let u" G L\Q). assumed in the following that all the equations hold good in the a.e. sense.

It will be

Equivalence of formulations (I), (II) and (III) (III) ^ (II).

Assume that there exists a w G M2 such that b

b

fu'^dx
0 implies

b

fv'^dx>0,

fv'^dx.

(7.2.115)

(7.2.116)

b

As (7.2.111) holds, the relation ./Q ?/(i/ - u')dx > 0 can be used in (7.2.116). The inequality (7.2.116) implies that u gives the minimum in (III).


169

(I) ^ (11). b

0

/ u{v' — u)dx

= u{v — U)Q — / u"{v — u)dx,

0

0 6

=

- j u{v-u)dx.

(7.2.117)

0

Let 0 = (0,6) = /i U /2, where Ii = {x eQ: u{x) = ^p{x)}; u" < 0 in A if formulation (I) holds,

(7.2.118)

l2 = {x en-.

(7.2.119)

u{x) > ip{x)}; u" - 0 in /2 if formulation (I) holds.

Using (7.2.118) and (7.2.119) in (7.2.117), we get h

fu{v'

- u')dx = - j u"{v - ^{x))dx > 0.

0

(7.2.120)

h

The integration by parts in (7.2.117) requires that u" should belong to L^{Q). Therefore (I) ^ (II) provided the solution u of (I) is such that u^' G L^{Q). FVom Fig. 7.2.1 it is clear that the solution may exist even if u" ^ L^{Q). It has been shown in [183] that if ip be such that ip" is a Radon measure and its positive part can be represented by a function belonging to L^(0, 6) then the condition u" ^ L^{Q) is not required. (II) => (I). Consider (7.2.117) and the case u>ip. and V e M2- If (II) holds, then

Letv = u+C. C > 0, C ^ C'^(^),

h

- fu"(dx>0.

(7.2.121)

0

The relation (7.2.21) implies u" < 0 in fl. Next consider the case u> if). Let v = u-\- eC,, ( E CQ^{I2)- Extend C to Q trivially, i.e., C = 0 in / i . If £ is sufficiently small, v will be greater then ijj and we have h

h

I u'{v' - u) dx = - j u"{v -u) 0

0

dx= -£ j u"C dx > 0. /

(7.2.122)

2

Since (7.2.122) holds for all sufficiently small £ which could be positive or negative, it can be concluded that fu'Xdx h

= 0.

(7.2.123)

As C is arbitrary, u" = 0 on /2. The equivalence of different variational inequality formulations of problems involving more general elliptic operators can also be discussed. For example, it can be proved that the variational inequality (7.2.1) with a{u,v) defined by (7.2.14) is equivalent to the variational inequality (7.2.37) in which the operator A is given by (7.2.13) provided ?i, the coefficients in the elliptic operator, and the obstacle ip satisfy some conditions [22].

170

7.3 7.3.1


The Parabolic Variational Inequality Formulation in appropriate spaces

Let Q be an open bounded domain in K^ and Qt^ = 0 x {0 < ^ < ^*}. One of the problems of mathematical physics is to solve the initial-boundary value problem stated below in (7.3.1)-(7.3.3). Tt + AT T T =

= /, i n ^ ^

(7.3.1)

= g, ondQt.,

(7.3.2)

To, in n X {0} ,

(7.3.3)

where A = -f: au{x. t ) ^ ? ^ + E H ^ ^ t)^^^^ iTî oxidxj ^ dxi dQu =dnx

+ d{x,t)T{x,0,

{0,t,).

(7.3.4)

(7.3.5)

dQt^ U 17 X {0} is called a parabolic boundary. The weak form of problem (7.3.1)—(7.3.4) can be stated in terms of finding a function T{x,t) € H^(QtJ satisfying the equation ( T „ v - T ) + a{t;T,v-T)

= (f^v-T),

(7.3.6)

for a.a. t G (0, t^) and all v G 7/^(0^ J . v satisfies the given initial and boundary conditions,

a(,T,.) = / ( E a . . £ | ; ; + E^.|;- + '^^^k ^^ = ^^ + E?^^

(7.3.7) (7-3.8)

ox J

= Ivwdx.

(7.3.9)

It has been assumed in (7.3.4) that the data, the temperature derivatives with respect to x and i, and coefficients a^j are suflBciently smooth functions (cf. [1] and proposition 7.3.1.). There does not exist a minimization principle for parabolic problems. Often Biot's variational statement [184] is taken as a variational principle. Every elliptic problem cannot be generalized to a transient problem, for example, the obstacle problem for the string (Problem 1.1.12.) does not have a time dependent generalization. If an obstacle is introduced in the formulation (7.3.1)—(7.3.4), then we may obtain an inequality.

7.3. The Parabolic Variational Inequality

171

Parabolic variational inequality for the problem in (7.3.1)—(7.3.4) can be defined in any of the following two equivalent forms. (I)

For a.a. t e (0,^=,), let E{t) =^{ve H\n);

V > i){x,t) a.e. in Q].

(7.3.10)

E{t) is a closed convex subset of H^{Q). To make E{t) a non-empty set, we shall take ilj[x,t) < g{x,t) a.e. on dQ for t G (0,^*). A function T{x,t) G L^{0,t^] H\n)),T{t) e E{t), for a.a. t G (0,^*), i.e, for each fixed t, T{x,t) = T{x) G H^{Q) is called a solution of the parabolic variational inequality (7.3.11) if {Tt,v-T)-â{t]T,v-T)>{f,v-T),

for a.ate{0,t,),

(7.3.11)

is satisfied for V ^; G L'^{0,t^;H^{n)) with v{t) G E{t) for a.a. t G (0,^*), v{x,0) = To and V satisfying (7.3.2). It is required that dT/dt G 1/^(0, i*; L'^{n)). ip{x,t) is called an obstacle, /(x,^), ip{x^t) and dQ should satisfy some smoothness conditions. Some of these conditions will be discussed for some specific problems to be discussed later. (II) The second variational inequality formulation is the integrated form of (7.3.11), i.e., in the place of (7.3.11), we have r^* dT Jo { ( ^ ' ^ - ^ ) + ^ ( ^ ' ^ ' ^ - ^ ) - ( / ' ^ - ^ ) } ^ ^ > 0 -

C^-3-12)

Let E = {ve L'^{0,t^]H\n));

v>ip{x,t)

a.e. in Q^., v{x,0)=To}.

(7.3.13)

v{x, t) satisfies the boundary condition (7.3.2). If there exists a function T(x, t) E E with dT/dt G 1/2(0, t^] L'î^)) such that (7.3.12) is satisfied for all v e E, then T{x, t) is called a solution of the variational inequality (7.3.12). Any solution of (7.3.11) will satisfy (7.3.12) and so the formulation (I) implies formulation (II). We assume that a solution T{x,t) of (7.3.12) exists. For some £ > 0 such that (^0 ~ ^5 ^0 + ^) ^ (0, t^), consider the following function. V

=

T[x,t),

t i

{to-£,to-\-£

=

V,

t e {to - £,to-\-£)

(7.3.14) If V defined in (7.3.14) is used in (7.3.12), then to+e

'71 dT J U^.v-T) ^ dt

+ a{t;T,v-T)~(f,v-T)\dt

> 0.

(7.3.15)

to-e

Since the interval (ô — £,to + £) G (0,^*) is arbitrary, we obtain (7.3.11). The complementarity problem corresponding to the parabolic variational inequality (7.3.11) in which

172


the operator A is given by (7.3.4) consists of finding T{x, t) satisfying the following system of equations. Tt + AT>

/,

T>ip{x,t),

\ inQt^.

(7.3.16)

{Tt + AT-f){T-,l;{x,t)) = 0,. The relations in (7.3.16) are satisfied in the a.e. sense and T G L^ (0,^*;//^(O)). The equivalence of the variational inequahty (7.3.12) and the complementarity problem (7.3.16) can be estabhshed. The proof is similar to the one discussed in the elliptic case (see § 7.2.3). Consider first the case T > ip, where T is the solution of (7.3.12). If 0 G C^(QtJ, 0 > 0 and 0 (x, 0) = 0 then v = T-{-(j) belongs to the set E.

/'

(Tt + AT -f)(t>dxdt = fli-^^y-

fit,

T)+a{t] T, v - T)-{f,v-

T)\dt > 0. (7.3.17)

0 '^

Since 0 is arbitrary, we conclude that dT/dt -\- AT — f > 0 in Q^,. Next, we consider the case T > ip and use the procedure followed in the elliptic case (equations (7.2.32)—(7.2.36)) with a difference that now v = T — scf), \£\ > 0, £ very small, 0 € Cîû) and (p{x,0) = 0. It can be seen that dT/dt + AT - f = 0. Combining the two cases T > ip and T > ip, (7.3.16) is obtained. To prove that (7.3.16) implies (7.3.12), consider the first integral on the l.h.s. of (7.3.17). On replacing 0 by (z; — T), writing v — T = v — ip— (T — tp) and using the third relation is (7.3.16) and the fact f > -0, we obtain {Tt + AT-f){v/

T) dxdt > 0, \f v e E.

(7.3.18)

•

fit»

Since (7.3.18) holds for all v e E,T is the solution of (7.3.12). In the elliptic case, the coercivity of the bilinear form played an important role in proving well-posedness and uniqueness of the solution. If the transformation f=

e-"*T, a > 0 ,

(7.3.19)

is used then Tt + AT = f is transformed into f;-h (/I + a) t = e - " 7 , and a{t]T,v)

(7.3.20)

is transformed into d{t] t , v) = a{t] f,v)-â

( t , v).

(7.3.21)

If a is sufficiently large, then irrespective of the fact that a(t; T, v) is coercive or not a{t] T, v) is coercive. Without any loss of generality it can be assumed from the start that a(t]T,v) is coercive and if for a.a. t, T G H^{Q) then a(^;T,T) > A||T||î > A / ( | V T | V T 2 ) c / a : , n

A>0.

(7.3.22)

7.3. The Parabolic Variational Inequality

173

Uniqueness and stability of the solution of (7.3.12) can be proved if coercivity condition is imposed on a{t]T,v) in (7.3.12). Let Ti and T2 be two different solutions of (7.3.12) satisfying the same initial and boundary conditions. Taking v = T2 in (7.3.12) and T = Ti, we obtain

'm^ T2 - Ti

+ a{t; T,T2 -T,)

- [f^T^-TM

dt> 0.

(7.3.23)

Similarly by taking T = T2 and v = Ti, a. second relation is obtained. Adding the two relations so obtained, it is easy to obtain the relation / U ^ (Ti - T2, Ti - T2) + a{t;T, - T2,T, - T^) \dt 0 and /, g, D^g, Dig, Dtg belong to CiClt^). C"(OtJ is the space of functions u{x,t) which are Holder continuous with exponent a, Ha{u) < oo. (5) \Dxaij\ < Ml (constant) so that a{t;u,v) can be defined.

(7.3.32)

If the above conditions are satisfied, then there exists a unique solution of the obstacle problem (7.3.11) ((7.3.12)) and D^T, DlT, DtT belongs to ^^(f^f J , Vp, 1 < p < oo.

7.4

7.4.1

(7.3.33)

Some Variational Inequality Formulations of Classical Stefan Problems One-phase Stefan problems

The variational inequality formulation is a fixed domain formulation and therefore weak enthalpy formulations of the Stefan problems are more suitable for variational inequahty formulations than the classical formulations of Stefan problems. Even in the classical Stefan problems, variational inequality formulations of one-phase Stefan problems can be handled easily than the two-phase Stefan problems. This is because a one-phase Stefan problem can be formulated in terms of the 'freezing index' which together with its gradient is continuous throughout the region. Also the constraint that the temperature is greater than or equal to (less than or equal to) the melting temperature holds throughout the phase-change region. We describe below some variational inequality formulations of one-phase Stefan problems. Some results concerning analysis of solutions of these problems are also given. Consider an open bounded domain Q in R^. At time t = 0 , 0 is filled with ice cold water at temperature T = 0 where 0 is the dimensionless freezing temperature of water. Let dQ = dQf{t) U dQ,e{t) U drtr{t) and on these three disjoint portions of the boundary, three diff"erent types of boundary conditions are prescribed. On the portion dQj coohng is done so that ice formation takes place. For ^ > 0, ^^ = ô{t) UQi{t) U r(^). rto{t) is the ice region at time t, 0 < t < t^, î{t) contains water at temperature T = 0 and r(^) is the

7.4. Some Variational Inequality Formulations of the Classical Stefan Problems

175

ice-water phase-change boundary whose equation is taken as f = (p{x)^ x ^ Q. Qo{t) and î{t) are disjoint regions. The mathematical formulation of this problem is as follows: ^

= V. {kVT),

in QQW, 0 0, then there exists a unique solution u(x,t) of the variational inequality (7.4.23) subject to the initial and boundary conditions (7.4.15)—(7.4.18) such that u e L\0, t,] H\n))

n L°°(0, t,; L^{n))] SLudu-V'

(kVu) G ^ ^ ( a j .

(7.4.25)

The numerical solution of the variational inequality {u,v —u)Q-\-{kVu,V{v —u))Q-\-{au,v — u)dn^'> {lc,v — u)n,

for a. a. ^G(0,^*),(7.4.26)

has been discussed in [188] by 'Galerkin approximation' in space and discretization by finite-diff"erence in time. A variational formulation of a two-phase Stefan problem has been given in [189] and its numerical solution has been obtained by finite-difference methods. The initial condition (7.4.18) imphes that at t = 0, 0 is occupied by ice cold water. We shall now consider the problem in which at t = 0 ice occupies a region Co with temperature g{x) < 0, Go C ft. ^ — GQ is filled with water at temperature T = 0. Let Qo{t) be the region occupied by ice at any time t and Qi{t) be the water region so that Q = Qo{t)UQi{t)[jr{t), where, QQ and ^ i are disjoint regions and r(^) is the ice-water interface whose equation is given by t = (p{x). li x e Go, then 0(a;) = 0. The initial and boundary conditions are given by (7.4.16)—(7.4.18). We assume that ice is progressing on water. The freezing index u(x,t) in this case is defined as u{x, t)=

f T(x, T)dT, in no(t) -Go,

0 0, Wf > 0 in Qo{t^). The region Qo{t) = {x : u{x, t) > 0} , 0 < ^ < ^* is expanding continuously with time. Further, the water-ice boundary F admits the representation F : x = a(t),

0i > 0, a > 0,

e{h,x',t) = e2{x\t),

onF2, ^ > 0 .

(7.4.47) (7.4.48) (7.4.49)

The geometry considered in [191] is different from the geometry shown in Fig. 7.4.1. as only one branch of the free boundary has been considered in [191]. By symmetry consideration, one branch of the free boundary can be considered in Fig. 7.4.1. also but the boundary condition at 2:2 = 0 will be different from that at X2 == a and not as in (7.4.48).


183

The boundary Fi is being cooled, n is the unit outward normal on Fi. The energy equation in Qt* = O x (0, t*) is given by ^^~d^~^^^^~\m^^^'d^)^^^''°^' ^'^' ^^ ^**•

(7-4.50)

Here, v = {VQ, 0,0) and VQ is the constant casting velocity in the direction of xi. Equation (7.4.50) holds in the sense of distributions. Let the free boundary be given by xi = S{x\t),

x' G ^2, t > 0,

(7.4.51)

where S{x', t) is a smooth function, S" : Q2 x (0, t^) —> [0, b). The conditions at the free boundary can be written as 0 = 0] &nd-^-V0.VS = l(vo-^). OXi

(7.4.52)

Ot

The second condition in (7.4.52) can be obtained by using relations of the type (1.4.19) and (1.4.21) and remembering that d[xi — S)/dt = VQ — dS/dt. The region Xi > S{x', t) is the solid region (see Fig. 7.4.1.) and the region Xi < S{x',t) is the melt region. Using the maximum principle, it can be proved that under the boundary conditions considered, for Xi > S{x',t), 6 > 0. Only dS/dt < VQ is physically admissible. In order to obtain variational inequality formulation of this casting problem, the following transformation has been used in [196] which regularizes the equation (7.4.50). t

u{x,t) =Vo f 6{XI-\-VO{T-t),x',T)dT,

x = {xi,x') eQ, t>Q,

(7.4.53)

0

where ^ is a non-negative function and is extended to —00 < Xi < S {x',t) by taking it to be zero in this extension. If ^ G Lj^^(QtJ, then 6 can be obtained in terms of u by the relation (cf. [196]) du du —- +Vo^— = voO, a.e. in Qt.. at oxi

(7.4.54)

It can be shown that u{x,t) formally satisfies the following equations. (JU

du

-^ + ^ 0 ^

Vû = fX{u>o)^ a.e. in Qt,, u>0,

u = 0, on Fo; and u = 0, at ^ = 0, ^ du

= a{g-u), du

onFi,

„, , ^

(7.4.55) (7.4.56) (7.4.57)

„

,

,

184


where f and g in (7.4.55) and (7.4.57) are given by (cf. [196]) /(x, t) = VQOO^XI - ht, x')Xj

g{xux\t)=

f

Oii^.t-^-

J

- Ivo [1 - X/], x ^ ^ . ^ > 0,

Vo

-,x)d^,

0<xi0.

(7.4.59)

(7.4.60)

[xi-bt] +

Here, [xi — bt] is the positive part of Xi — bt and Xi is the characteristic function of the set / related to the initial position of the free boundary $(0), and / is given by I = {{xi,x\t)

e^ty,

xi > S{x\0) + bt},

(7.4.61)

/ c n+ = {{xux\t) e a.; xi > S{x',t)} = {e> 0}, $(0) -.xi = S{x',0).

(7.4.62)

The equations (7.4.54) and (7.4.55) hold in the sense of distributions and the reader is referred to [196] for their derivation which is not straightforward. For t > b/vo, X/ = 0 ^^^ X{u>o) > X/ ^^ ^ > 0 because dS/dt < VQ. TO write the variational inequality formulation, we introduce the following notations. a{u,v)=

fVu'Vv

+ vofv-^-\-afuv,

u{t), v{t) e Mi{t),

{u,v) = [uv + — [uv, u{t), v{t) e Mi{t), J n

{Git),v) = Jf{t)v

VQ

J r2

+ ajg{t)v-h

Je2{t)v, v{t) e M,{t),

(7.4.63)

(7.4.64)

(7.4.65)

For a.a. t G (0.^*) M{t) = [v e H\n)-

V = 0, on Fo} , Mi{t) = {v e M{t)- v > 0, on 0} . (7.4.66)

The problem (7.4.55)—(7.4.58) has the following variational inequahty formulation. {du/dt,v-u)

+ a{u,v-u)>

(G{t),v-u),

a.a. t e {0,t,),

\fv(t) G Ml, u{t) e Ml.

(7.4.67)

If there exists a ii{t) G Mi(^) such that (7.4.67) holds for all v{t) G M[(f), then u{t) is called a solution of the variational inequality (7.4.67). If may be noted that the boundary conditions (7.4.57) and (7.4.58) occur as natural boundary conditions in the fornnilation and so only the boundary condition on FQ has been imposed on v.


185

Under suitable assumptions, existence of the unique solution of the variational inequality (7.4.67) has been discussed in [191, 196]. If has been shown that the free boundary has in fact the representation (7.4.51) such that dS/dt < VQ and {9, S) is the classical solution of the continuous casting problem. Oxygen - difTusion problem In the background of the previous formulations, variational inequality formulation of ODP discussed earher in § 3.3.2 does not present much difficulty. We consider equations (3.3.34)-(3.3.38) and take Q = [0,1], Vtt^ = Q x (0,^*), Qoit) = {x; 0<x < S{t)}, 0 < t < t^. In the region Oo(t), the concentration c > 0 and in Q\0o(^), c = 0. Therefore in 0, c > 0. Note that in ODP, the region under consideration is only Qo{t) and no constraint of the form c > 0 is imposed. The variational inequality problem is studied in the fixed domain Q, and the constraint c > 0 has been added to study an obstacle problem. It can be seen that

n 0 on

- /

\^

0 an0

^ '

dc\ (^ - c) ^

' dc d dx+ I I - ^ — {v - c) dxdt + f [ {v-c)

dxdt.

(7.4.68)

0 0

The test function v{x,t) satisfies the same initial and boundary conditions as the concentration c{x, t) and so the second term on the r.h.s. of (7.4.68) is zero. On rearranging equation (7.4.68), we obtain -

+ //(.0 0

iv - c) dxdt+ jj^--{v-c)

c) dxdt = / / ( I

- £

dxdt

+ l) vdxdt.

(7AM)

We have c^ — c^x H- 1 = 0 if c > 0 and Q — c^x + 1 is equal to 1 if c = 0. Therefore, Q — Cxx + 1 > 0 for c > 0 and c {ct — Cxx + 1) = 0 in Q. As i; > 0, the last term on the r.h.s. of (7.4.69) is greater than or equal to zero and we get Jlicuv-

c) + ( ^ , -^{v-

c) J + (1,^; - c)\dt

> 0.

(7.4.70)

This completes the variational inequality formulation of ODP. If there exists a function c{x,t) e E, where, E = {v e L^(0,t*; H\Q)) ; v > 0, a.e. in Q,^,t;(x,0) = c(x,0)}, and c(x,t) satisfies (7.4.70) for all v e E then c(x,t) is called a solution of the variational inequality (7.4.70). In the multi-dimensional case when 0 C -R", n > 1, the variational inequality formulation can be obtained following the procedure adopted in (7.4.68)—(7.4.70). The integration by parts will then require the use of Green's formula.

186


If oxygen-diffusion takes place in a subset of /?", n > 1 then the initial concentration has to be suitably prescribed as in this case it is difficult to obtain it from the solution of a steady-state problem which was possible in the one-dimensional case. The existence, uniqueness and regularity of the solution of (7.4.70) was studied in [74]. Some regularity results for the one-phase Stefan problems have been reported earlier in this section and for further information, see [197, 198, 199]. Is it possible to obtain a one-phase Stefan problem from its variational inequality formulation? Consider the problem of finding a function u{x,t) satisfying the following complementarity problem. Ut — Uxx > /, "^ > i'i^^t),

and {ut — u^x — f){u — tp) = 0, a.e. in Qt^,

nt.=nx{o 0,

(7.4.74)

r ( x , 0) = To{x) = ^'(x) + (/ - iJt)t=o. 0 < x < 1,

(7.4.75)

T(0, t) = f{t) = ut~ ^PtUo^ t > 0,

(7.4.76)

T{S{t),t)

= 0, t > 0, 5(0) = 1,

Tx {S{t),t) = X(S{t),t) S(t) = (/ + w.. ~ 'M \x^sit)S{t). t > 0

(7.4.77) (7.4.78)


187

By choosing F, TQ{X), f{t) and X{S{t),t) suitably in (7.4.74)-(7.4.78), a one-phase Stefan problem or an ODP can be obtained. On inverting (7.4.73), we get t

u (x, t)=

j T{x, rj)dr] -f V^(x, t),

(7.4.79)

4>{x)

on the free boundary t - S~\x) = 0(x). From {7.4.79), u{S{t),t) to derive (7.4.78), calculate Ut — u^x from (7.4.79) at a: = S{t).

= if; {S{t),t). In order

The equivalence of the weak formulation of a one-phase Stefan problem and its variational inequality formulation has been discussed in § 11.2.2.

7.4.2

A Stefan problem with a quasi-variational inequality formulation

Our interest in this section is only in introducing the quasi-variational inequality. For a rigorous discussion of the quasi-variational inequality, see [22] and the references mentioned there in this connection. One of the forms of quasi-variational elliptic inequality considered by BensoussanGoursat-Lions (cf. [200]), and further discussed in [22], can be defined as follows: Let Hi and H2 be two Hilbert spaces and v = (iii, ^2) be the generic element oi H = HiX H2. Define a : H x H -^ R and g : H -^ R as follows: a{w, z) = ai{wu zi) -h a2{w2, Z2) + bi{wuZ2) + 62(2^2, ^î), g{w) = gi{wi) + g2{w2).

(7.4.80) (7.4.81)

Here, ai : Hi x Hi —^ R and a2 : H2 x H2 —^ R are continuous bilinear forms, symmetric and non-negative along the diagonal, bi : Hi x H2 —^ R and b2 . H2 x Hi -^ R are continuous bihnear forms, gi : Hi -^ R and g2 • H2 —^ R are continuous linear functional. Let D C H = Hi x H2 he a non-empty closed convex set. li v e D, then define D{v) = Di{v) x D2{v) where Di{v) = {zi G Hi : {zuV2) 6 D} , and D2{v) = {22 e H2 : {vuZ2) G D} . (7.4.82) An inequality a{u,u-

v) < g{u - v), \fv G D{u), ue D

(7.4.83)

is an example of a quasi-variational inequality. D{v) is a non-empty closed convex set of D^ = PH^{D) X PH2{D), where P//^ and P//2 are 'projection operators'. \iu ^ Hi and VK C //i is a non-empty closed convex set, then Pw{y) is that element of W which is nearest to u. The inequality (7.4.83) is a variational

188


inequality when for V 2i G D, D{u) = Q = Qi x Q2 with Qi being a non-empty closed convex set of Hi and Q2 being a non-empty closed convex set oi H2. v E D{u) suggests that quasi-variational inequality entails a convex set of competing functions which may depend on the possible solution whereas in the variational inequality formulation convex set is fixed. A family of variational inequalities can be associated with the quasi-variational inequality (7.4.83). If u is fixed in D, then along u, we can consider a variational inequahty concerned with finding ai w E D(u) such that a{w, w -v)

< g{w -v),

\/ v € D{u).

(7.4.84)

A quasi-variational inequality formulation for the following one-phase Stefan problem has been studied in [201, 202]. Find a function T{x,t) and the curve T : x = S(t), 0 < t < t^ such that ^« - Txx = 0, 0<x
0, A^ < 0 and To(x) > A(x, 0), 0 < X < ô; and T{So, 0) = A(6'o, 0).

(7.4.96)

We define a function g(x) as follows: g{x)

=

r

(r(^, 0) - A(C 0)) d^,iiO<x
0, e+ < e < e_,

(8.3.14)

T(e) - T(e_) - ^^^"^

(8.3.15)

^^''^\e

- e_) < 0, e_ < e < e+.

The relevance of (8.3.12)—(8.3.15) in the present problem is that when e„ > 1 and 5" > 0, then necessarily, e^ = T^ = 0 and we have the following one-phase melting problem. Tt + q.^ = 0, and g^ + ^ + T, = 0: 0<x

< S{t), t > 0,

(8.3.16)

8.3. Model II: Formulation with Temperature Discontinuity at the Interface

q{S{tlt) ^ [T(l + T)]'/\S{tltl

and ^

= (-L_y/2^s{tlt),

209

(8.3.17)

T(0,i) = T o > 0 , t > 0 ,

(8.3.18)

(e,T,q){x, t) = (0,0,0), x > S{t), t > 0,

(8.3.19)

e(x, ^) - 1 + T(x, ^), 0 < a: < ^(t), ^ > 0.

(8.3.20)

At this point the necessity of considering the present new model can be questioned. Model I seems to be a good model as it is based on the conservation law of energy and incorporates generalized Fourier's law. As r ^ 0 in the telegrapher's equation and in the Stefan condition (8.2.13) {TS = TL = T), we get back the classical Stefan problem formulation and for r —> 0 even the solution in (8.2.14)—(8.2.19) is the solution of the corresponding Stefan problem. The neessity of considering different models (we shall be considering some more models) for hyperbolic Stefan problems arose from the fact that we should be able to prove the existence and uniqueness of the solution and the well-posedness of the problem under general initial and boundary data and as r -^ 0, the solution of the hyperbolic Stefan problem should converge to the solution of the classical Stefan problem. The solution given in (8.2.14)—(8.2.19) is the solution of a very special type of problem. There does not exist a general result for the hyperbolic phase-change problems which may tell us that as r -^ 0, the solution of a problem formulated with the help of the model I, or for that matter any other model, will tend to the solution of the classical Stefan problem. Different authors have considered different mathematical models, showed the existence and uniqueness of solutions and tried to estabhsh the convergence as r -^ 0 by considering some specific problems. For model I, some results on the existence, uniqueness, and regularity of the solutions of some hyperbolic Stefan problems have been discussed in § 8.2.1 but no result has been reported in [213, 214, 215, 216] on the convergence of the solution as r -^ 0.

8.3.2

The existence and uniqueness of the solution and its convergence as r -^ 0.

The existence of the weak solution of the problem (8.3.16)—(8.3.20) has been discussed in [217] and for this the functions T, q and e considered in 0 < x < S{t) and satisfying (8.3.16)—(8.3.20) are expressed in terms of Riemann invariants (cf. (8.2.36)). {T,q,e) = (0,0,0) for x > S{t). Temperature is prescribed at x = 0. A family of problems parameterized by a time lag r are considered and the desired solution is obtained as T -^ 0. It has been shown that T, q and e defined by Riemann invariants satisfy the boundary conditions and for every simple closed curve C in {0 < x < S{t), t > 0} surrounding a domain R(C), we have / {e{x,t)dx-q{x,t)dt} = 0,

(8.3.21)

210

The Hyperbolic Stefan Problem

f{q{x, t)dx - T{x, t)dt} + / jq{x, i)dxdt = 0.

(8.3.22)

R{C)

The integration along C is taken in the clockwise sense. The Rankine-Hugoniot conditions are satisfied in the sense that for every 0 < î < ^2 < oo j ' ' [e[S[t), t)S{t) - q{S{t), t)}dt = 0,

(8.3.23)

and f {q{S{t),t)S{t)

- T{S{t),t)]dt

= 0.

(8.3.24)

ti

The short and long term asymptotics of the solution of (8.3.16)—(8.3.20) were also obtained. The problem considered in [219] is also one-phase with temperature being discontinuous at the interface. The initial and boundary conditions considered are functions of space and time, respectively. In the problem formulation, to start with, energy e{x,t) is taken as e = eoiT) + Z{T)q\

(8.3.25)

where, eo(T) is the classical internal energy as considered in (8.3.7) and Z{T) is defined as

The function Z{T) is a consequence of the second law of thermodynamics combined with the generalized Fourier's law [220]. The coefficients T{T) and K{T) depend both on the temperature and the phase-change material under consideration and they can have jump discontinuities at the phase-change temperature. If it is assumed that r{T)/K{T) is differentiable at T = 0 (zero is the phase-change temperature) and e given in (8.3.25) is substituted in the first equation of (8.3.6), then we have deo

1 d

d TK(T) ')

(r{T)\\

'^ '^'^ 2dT\K{T))]' T^(nn\ \ I ^

(8.3.27)

The r.h.s. of (8.3.27) is too complicated and it is difficult to carry out further calculations on retaining it in the present form. If it is assumed that r{T)/K{T) = constant for all T, T{T) = constant and a small number, and 1/T is small, then the r.h.s. in (8.3.27) can be taken to be 0. We have now the same formulation as in (8.3.16) and (8.3.17). However, the initial and boundary conditions considered in [219] are more general.

8.3. Model II: Formulation with Temperature Discontinuity at the Interface

211

Dirichlet Problem T{x, 0)

=

0(x) > 0, and q{x, 0)=il;{x); 0<x

< S'(O), ] [

T{0,t) = / W > 0 , t>0.

(8.3.28)

J

Another type of boundary condition at a: = 0 could be the 'Neumann boundary condition'. Neumann Problem T(x, 0)

=

(t){x) > 0, and q{x, 0)=ip{x)] 0<x
0.

S'(O), ] i J

(8.3.29)

As reported earher, it is convenient to work with the Riemann invariants A and B which in [219] are defined as A = T + yjrq; and B = T-

y/rq.

(8.3.30)

Substituting (8.3.30) in (8.3.16) and (8.3.17), we get y/Ât + v4, + (A - B)/{2y/T) = 0, 0<x< y/^Bt-B^

+ {B-A)/{2y/f)

B{S{tU)

S{t), t > 0,

= 0, 0<x<S{t),

= -^^^{S{t),tl

t>0,

t > 0,

(8.3.31) (8.3.32)

(8.3.33)

For the Dirichlet problem (8.3.28), we have A{x,0) = Ao{x), B{x,0) - Bo{x), 0<x
0.

(8.3.35) (8.3.36)

For the Neumann problem (8.3.29), we have A(0, t) + 5(0, t) + 2 v ^ / ( t ) , t > 0,

(8.3.37)

and the equation (8.3.35). To discuss the existence, uniqueness, and regularity results, the following assumptions have been made [219]. / G C^ [0, oo], 0 G C'^ [0, S{0)], êC^

[0, S{0)],

(8.3.38)

212

The Hyperbolic Stefan Problem (t){x) > -y/î;{x),

(f){x) > Vriîx) - 1/4; if 0 < a; < 5(0).

(8.3.39)

If there exists a C^ solution of (8.3.31)—(8.3.35) and (8.3.37), then the following compatibility conditions hold good. ^ ( 0 ) = J5o(0) + 2v^/(0),

(8.3.40)

>lo,x(0) + Bo,x(0) = - 2 ( r / ( 0 ) + /(O)),

(8.3.41)

5(0) = 5o, 5'(0) = 5i, 5''(0) = 52,

(8.3.42)

and

where 5o > 0 is given and

0 there exists at most one C^ solution {A, B, 5) of (8.3.31)-(8.3.35) and (8.3.37) for 0 < ^ < î. The above two results are for the Neumann problem. For the Dirichlet problem, the existence theorem requires that the data satisfy the assumptions f'{t) > 0, 0 < t < 00,

]

[ -(t>'{x) > ^/TW{x)\,

(8.3.47)

0 < X < 5o, 0(5o) + V^^(So) > 0. J

Proposition 8.3.3. If (8.3.38)-(8.3.41) and (8.3.45)-(8.3.47) hold and if one can establish an a priori estimate A(S{t), t) > -l/2-\-£r for some e^ > 0, 0 < ^ < ti < 00, Sr

8.3. Model II: Formulation with Temperature Discontinuity at the Interface depending on r, and ti, then there exists a solution {A,B,S) with S e C^'^ and A, B e C^'^ up to the boundary.

213

of the Dirichlet problem

A uniqueness result similar to that given in Proposition 8.3.2. holds good for the Dirichlet problem also. Asymptotic behaviour of the one-phase problem as r —> 0 was also investigated in [219] and the Proposition 8.3.4 given below was proved under some assumptions. Proposition 8.3.4. Consider the Dirichlet problem stated in (8.3.28). The solution Tr (T depending on r) of the Dirichlet problem with T^ = 0 in x > Sr{t), tends to u as r -^ 0 weakly in (L°° {0 < x < M, 0 < t < ti})* for any M > 0, ti > 0, where u is the solution of the one-phase Stefan problem stated in (8.3.48)—(8.3.50). tif - tixx = 0, 0 < X < S{t), t > 0,

(8.3.48)

^(0,t) = f{t), t > 0; n(x,0) = ^(x), 0 < x < ^(0),

(8.3.49)

w = 0, Wx = --j-]

on X = S{t).

(8.3.50)

Here, /(t) and (t){x) are the same as in (8.3.28). A result similar to Proposition 8.3.4. could not be proved for the Neumann problem as the solution of Riemann invariants cannot be obtained by integration along characteristics. A one-phase three-dimensional hyperbolic Stefan problem with discontinuous temperature was studied in [221]. The constitutive equations which hold throughout the region consisting of solid and liquid phases are taken as ^ - h V . ( f - 0 , a n d r | ^ - h g + V ( i ^ r ) = 0; f = (gi, ^2, â).

(8.3.51)

The first equation in (8.3.51) holds in the weak sense as the energy e = e[T) is discontinuous across the phase-change boundary whose equation is given by (t)[x\,X2X^,t) = X'i — S{xi,X2,t) = X3 — S{t) = 0. Across the shock Xs = S{t), the following RankineHugoniot conditions hold. [rqi] S,

+

[KT] 5,, = 0, ^

[rqJi St

+

[KT] S,, = 0, \

lrqs]St

-

(8.3.52)

[AT] = 0,

[e]St + [gi] S,. + [92] S,, - [<j;,] = 0.

(8.3.53)

214


Here, [/] denotes the jump in f across the interface (p = 0 and Cs = CL = C and Ps = PL- It is easy to derive conditions (8.3.52) and (8.3.53) from equations of the type (8.3.9). Since the energy function is non-convex, one cannot expect the twophase problem to be well-posed even in the one-dimensional case and therefore only one-phase problem has been considered in [221]. The hquid occupies the region 0 < X3 < S{t) in R^, S(xi,X2,0) = So{xi,X2) and the initial conditions for the liquid region are given by T(X, 0) = To{x) > 0, X = (Xi, X2,X3) ]

> , 0<X3<So. J

q{x,0) = qo{x)

(8.3.54)

T — 0 is the phase-change temperature. The initial conditions for the solid region are given by T(x, 0) = 0, q{x, 0) = 0] X3> So. (8.3.55) Let U = {qi,q2,Q3, T)^^, where T^ is the transpose of a matrix. The hyperbolic system consisting of equation (8.3.51) can be written in the form of the following matrix equation 3

CU = Ut + Yl ^J^^j

+BU = 0,

(8.3.56)

j=i

where Aj, J=l,2,3 and B are 4 x 4 matrices which can be easily written. As we saw earlier, for the existence and uniqueness of the solution, some compatibility conditions are to be satisfied at SQ. These are the conditions imposed on the traces of an initial data {To,qo) at X3 = S{0). The compatibility conditions can be obtained by comparing the two values of Ut{x, 0) at X3 = S{0), one computed from the interior equation (8.3.56) and another from the interface conditions (8.3.52) and (8.3.53). Higher order compatibility conditions can be obtained similarly (cf. [222]). The compatibility conditions can also be stated in an equivalent way as follows. The initial data in (8.3.52)—(8.3.56), are said to satisfy k-th order compatibility conditions if there exist a C^- approximate solution (f7, S) of (8.3.52)—(8.3.56) such that U{x,0) = Uo{x), S{xi,X2^0) = So{xu2:2),

(8.3.57)

CU = 0(^^),

(8.3.58)

D{U,S) = 0{t^),

(8.3.59)

where the system of equations (8.3.52) and (8.3.53) is briefly denoted as D{U, S) = 0. Uo{x) is the value of f/ at i = 0 and the operator C is the same as in (8.3.56). The main result of [221] is the following proposition. Proposition 8.3.5. The hyperbolic Stefan problem (8.3.52)—(8.3.56) has a unique classical solution (f/, S) e H^({0, to) x R^) x //^+^((0, ^0) x i?^) for some ^0 > 0, provided the following conditions are satisfied.

8.3. Model II: Formulation with Temperature Discontinuity at the Interface 1. Uo{x),

215

So{xuX2)eC^.

2. k-th order compatibility conditions (8.3.57)—(8.3.59) are satisfied for k > 4. 3. St{xi,X2,0) (n + l)/2 + 2. There are four main steps in the construction of the proof of Proposition 8.3.5. First, the free boundary is fixed by the transformation xs — S{t) = ys, xi = yi^ X2 = y2 so that in the new coordinates, equation (8.3.56) becomes Ci{S)U = 0, in 2/3 < 0 ,

(8.3.60)

where

The free boundary conditions remain of the same form as stated in (8.3.52) and (8.3.53). The second step is to formulate the given problem in terms of new variables (V, ^) which satisfy the homogeneous initial conditions. V and ^ are defined by the relations U = 0 + V; S = S + ^.

(8.3.61)

The existence and uniqueness of the solution of the original problem can be established if the same can be proved for the problem formulated in terms of the new variables (V, ^ ) . The third step is to linearize about {U,S) the nonlinear problem formulated in terms of (y, ^ ) and to prove that the linearized problem is uniformly stable. The linear boundary value problem for (V, ^ ) will be uniformly stable if the solution (V, ^ ) satisfies the estimate (of. [223]) V ml,

+ \y\l, + l ^ l L ^P(l

ll/llo,. + l^lo,,). for n > r?o,

(8.3.62)

where ||V H^^^ is the hyperbolic r]-weighted interior norm defined as W\\r,v=Yl

and IVI

J

\d^Âe''''y)\^dxidx2dx3dt,

xeR\

(8.3.63)

is the boundary norm defined as \n,,=

E

/

\dr,i.,,.Je-''V)\'dx,dx2dt.

(8.3.64)

Here, (/, ^f) are smooth functions which have zero traces at t = 0 upto the order k and are defined as follows: / = Ci(S + *)(f7 + V)-

Cr{S){U), y, < 0,

(8.3.65)

216

The Hyperbolic Stefan Problem g = D{U + V, 5 + ^) - D{U, S).

(8.3.66)

It has been proved that under the assumptions about the initial data in Proposition 8.3.5, the smooth solution of the linearized problem satisfies (8.3.62) near (y,t) = (0,0), y =

(2/i,?/2,?/3)-

Proposition 8.3.6. If the linearized problem is uniformly stable, then for any A: > 0 there is a unique solution (K, ^) G H^ x H^'^^ satisfying (8.3.62) near (0,0) with the subscript zero in (8.3.62) replaced by k and the subscript one replaced by A: + 1; the constant P (depending on k) in (8.3.62) depends on the local H^ norm of the coefficients with m = max (A;, 4). The fourth step is to use an iterative method to show the existence of a unique classical solution (]/, ^ ) in the neighborhood of (0, 0). Only linear iterations can be employed as for the linearized problem the estimate of the boundary function ^ is one order higher than the estimate of V. For the solution of the nonlinear problem formulated in terms of (y, ^ ) , the following result holds good. Proposition 8.3.7. Consider A: > 4 in the nonlinear problem formulated for (1/, ^ ) and assume that the following conditions hold good. 1- ifi 9) ^ ^^ with zero traces at ^ = 0 up to the order (A: — 1). 2. At {V, ^) = (0, 0), the boundary value problem is uniformly stable, i.e, the estimate in (8.3.62) is satisfied. Under the above conditions there exists a ^0 > 0 such that in (0, ^0), problem for (]/, ^) has a unique solution e H^ x H^^^. Moreover,

riwnl

IM "*"

\K,M , + l*1^

Here, the norms || •Ilm,r7,i0 and norms ||.||^^, and

,^,^0

l-L, ^,^0

< A ( 'Jii/C„

+iîLôj ,

for Tj

the nonlinear

> 7/0. (8.3.67)

denote , respectively. the restriction in [0, ^0] of the

l-U-

8.4

8.4.1

Model III : Delay in the Response of Energy to Latent and Sensible Heats The classical and the weak formulations

In this model, it will be assumed that along the solid-liquid interface, the energy response to the latent heat release (storage) is delayed by the same amount of time as the delay in the response of flux to the temperature gradient. Independently, the specific heat may be delayed or advanced with respect to the total energy by an increment de|)ending on the phase. This seems appropriate in order to match the wave speeds of

8.4 Model III: Delay in the Response of Energy to Latent and Sensible Heats

217

the hyperbolic equations on either side of the phase-change interface. If it is assumed that the response of energy to the latent heat is instantaneous, following a delay of relaxation time T, and if the response of energy to the specific heat is not delayed, then the total energy during the phase-change is given by (8.1.6). As discussed earlier this leads to an unrealistic situation. To have a well-posed problem and render it consistent with the wave speeds in solid and liquid phases and also consistent with the delay in the energy response to the latent heat, the following constitutive relations have been considered in [211]. ^nd

-{q{t)+Tq\t)) 1 + r-)e{t)

= (1 + g{r)-)C{T)

= KVT, + /^W, ? e H,{T).

(8.4.1 (8.4.2)

Here, P(T) - r^ if T < 0 and p(r) = r^. if T > 0, C{T) = CgT if T < 0 and C[T) - CLT if T > 0. T5 and TL are relaxation times for the response of energy to the specific heats in the pure solid and the pure liquid phases, respectively. ^ is the fraction of liquid present in any region. ^ = 0 for the pure solid, (f = 1 for the pure liquid and 0 < ^ < 1 for the mushy region whose temperature is T = 0. Hg is the Heavyside graph (cf. (4.3.45)). {q(t)-VTq{t)) and {e{t)-^Te'{t)) are assumed to be piecewise smooth in the total region under consideration. The first term on the l.h.s. of (8.4.2) is the first order approximation of e(^ + r) and the first term on the r.h.s. of (8.4.2) is the first order approximation of C{T{t + Tj)), J = S,L. The essential assumptions in (8.4.2) are: (1) the latent heat affects the energy after a delay of time r, and (ii) the specific heat affects the energy after a delay of r — rj^ J = 5", L, in the corresponding phase. When rs = TL = r, equation (8.4.2) can be integrated and we get oo

e{t) = C{T{t)) + H/T) J exp(-p/r)C(t - p)dp, ^ 6 H,{T).

(8.4.3)

0

Derivation of energy conservation equation for the two-phase problem The energy conservation principle and the relation (8.4.2) will now be used to derive energy conservation equation in the phase-change region. We first obtain the classical formulation and consider the case in which only solid and liquid regions exist which are separated by a smooth interface r(t). The densities of both the phases are taken to be the same . Let G C R^, be a fixed open bounded region and G = Gs{t) U Giit) U r(^), 0 < t < t^. The subscripts S and L stand for solid and liquid regions, respectively. Hyperbolic equations admit discontinuous solutions along shocks. Such shocks will be accommodated in the formulation. The time dependence of Gs, GL and F wiU not be indicated in the further discussion of this problem. The regions Gs and GL are disjoint. The external boundary of G is denoted by dG^ = dG^g U dG^^ where dG^g and dGî^ are the external boundaries of solid and liquid regions. Let dGs be the boundary of the solid region when the liquid region is removed from G and let dGi be the boundary of the liquid region when the solid region is removed from C, i.e., dGs = d^Gs^ L and dGi — d^GÛ T. It will be assumed that dG^ and F are sufficiently smooth and the outward drawn normal

218


can be defined uniquely on them. The energy conservation principle when applied to G gives [ e{t)dx - -

/ q{t). nda + f F{t)dx.

(8.4.4)

dC^

Here, n is the unit outward normal to dG^ and F[t) is the intensity of the heat source. By virtue of the constitutive relation (8.4.2), e(^) is difFerentiable in G and the time derivative on the l.h.s of (8.4.4) can be taken inside the integral. According to (8.4.1), q{t) is also differentiable, therefore, on differentiating (8.4.4) again with respect to time, we obtain J fe\t)dx

=-

G

f q\t). nda-\- f F\t)dx. dGb

(8.4.5)

G

It will be assumed that G, dG^ and, n on dG^ do not change with time. Multiplying (8.4.5) by r and adding (8.4.4) to it, we obtain J j{e(t) + Te'{t))dx = G

f {q{t) + rq'{t)). nda + f{F{t) + TF'{t))dx. dG^

(8.4.6)

G

In C, e(^) +Te'{t) is only piecewise smooth but in Gs and GL, e{t) -\-Te'{t) is smooth. Therefore in (8.4.6) we consider Gs ^ GL. The normal n should be defined in such a way that it is consistent with boundaries of both regions Gs and GL- Therefore n will have opposite directions on F when F is approached from liquid and from solid regions. On r , n is time dependent and it will be denoted by A^ which points into the liquid. The boundary of Gs includes F which is moving with a velocity V{t) and we have (see (2.4.12)) / (e(^) -f Te'{t))dx = GSUGL

f ^{e{t) + Te'{t))dx + / [e + re'] (V-N) da

(8.4.7)

GSUGL

In (8.4.7), we calculate d/dt from the first principle and assume that F does not have any surface energy. Equation (8.4.6) when written for Gs U GL will have the following form d

I ^^^^^^ ^ re\t))dx GSUGL

+ / [e + re'] {V • N)da = r

j [q[t) + Tq'{t)\ -Nda^

J {q{t) + Tq'{t)).nda dG^ûdGl

j {F(t) + TF'(t))dx.

Here, [e + re'] and [q-^ rq'] denote jumps in e{t) + Te'{t) and q{t) + Tq'(t) across F. The surface integral in (8.4.8) can be converted to a volume integral. The direction of


219

the normal on F from the sohd side is opposite to its direction from the hquid side. Since (8.4.8) holds for any G and F and for any t > 0, the following equations should hold. j^{e{t) + Te'{t)) H- V. {q{t) + Tq\t)) = F{t) + rF^t) in G\r,

0 < t < t,.

-[e(^) -h Te'{t)]Nt = [q{t) + Tq'{t)]. iV^, on F, 0 < ^ < t,.

(8.4.9) (8.4.10)

Here, A^ = {Nt^Nx)) and A^^; = (-^xi, ^X2 5 ^xs), x = (xi,X2,X3). If S denotes the union of F and some other surfaces of discontinuities (shocks) of e{t) + Te'{t) and q{t) + Tq\t) in G other than F, then in (8.4.9) and (8.4.10), F should be replaced by S. Next, we assume that G consists of solid, liquid and mushy regions and G — Gs{t) U GM{'^) U Giit) U Fi(t) U F2(t). Note that there could be surfaces of discontinuities other than Fi and F2 also. In Gs{t), we have T < 0, and in Giit) we have T > 0. GM{t) is the mushy region in which the temperature is T = 0. The hquid fraction ^ = ^{x, t) is equal to 1 and 0 in liquid and solid regions, respectively, and 0 < ^(x, i) < 1 in the mush and is assumed to be a smooth function of t in the mush. Fi(t) is the solid-mush boundary and F2(^) is the liquid-mush boundary. Gs{t), Gît) and Gi{t) are mutually disjoint regions. Fi(t) separates the solid region from the mush and F2(^) separates the mush from the liquid region. The external boundary of G will be denoted by dG^ and dG^ = dG^s U dG^M U dG\. Here, dG%, dG\^ and dG^ are the exterior boundaries of solid, mush and liquid regions respectively. Let dGs be the boundary of the solid region when liquid and mushy regions are removed from G, i.e., dGs — dG\ U Fi and similarly let dGu = dG\fUri{t)[jr2{t) and OGL = aGÛF2(i). The outward drawn normal n to dGs, 9GM and dGi is defined in such a way that it is continuous on the portions common to these boundaries. In order to obtain relations of the form (8.4.10) on Fi(^) and F2(t) and the energy equation (8.4.9) in G\FiUF2, we follow a procedure similar to that used above to obtain (8.4.8). Repeating arguments which lead to (8.4.9) and (8.4.10), we get the energy balance relations on Fi and F2 and the energy equation in G\ri u F2. Let 5"= F1UF2U (shocks other than Fi and F2). The classical formulation of the three region problem (take the densities of the three regions equal to one) is concerned with finding a pair (T, (J), satisfying the system of equations (8.4.11)—(8.4.16) for 0 < ^ < t^. ÂrsCs^ + CsT) - KsV^T = F -h TF\ in Gs- S, dV " ^ dt 1^^=F

J^(^LCL^

+ TF\ in GM-S,

+ CLT + 0 - KL^'T

/(I - 0 + ^LCL^]

(8.4.12)

=F + TF\

Nt = Kiyr.

(8.4.11)

in GL~ S ,

Nx, on F2,

(8.4.13)

(8.4.14)

220

The Hyperbolic Stefan Problem -^^"^^sCs^j

râ

dT_

Nt = KsVT. TV,, on Ti,

(8.4.15)

Nt = K^[VT]. TV,, on S - ( F i U Ta).

(8.4.16)

Here, i = S oi L depending on whether T < 0 or T > 0. T = 0 on Fi and r2 and N = {Nt, N:i:) is the normal on a surface of discontinuity and TV points into the hquid. [/] denotes the jump in / across a surface of discontinuity. Equations (8.4.11) and (8.4.13) are telegrapher's equations. Equation (8.4.12) regulates the water fraction in the mush. Equations (8.4.14) and (8.4.15) are energy balance conditions at the phasechange boundaries (cf. (8.4.20) for their derivation). The propagation of wave fronts is described by (8.4.16). To complete the formulation, equations (8.4.11)—(8.4.16) should be supplemented with the initial and boundary conditions. For example, T{x, t) = 0, xe dG\ 0 0, = V2{x) for To{x) < 0, = V3{x) for To{x) = 0. To derive energy balance condition (8.4.14) on F2 and (8.4.15) on Fi we consider two one-phase hyperbolic Stefan problems with the assumptions about the delay in the response of flux to the temperature gradient and the delay in the energy response to the sensible heat. At the liquid-mush boundary F2, the energy balance condition without any approximation gives -q{t + T).N, + (/(I - e) + CLmt

+ T[^))V. N, = 0.

(8.4.20)

For simplicity we take densities of all the phases equal to unity. The first order approximations of q[t -h r) and Ti{t -h TI) when substituted in (8.4.20) give the equation (8.4.14). Similarly by considering the energy balance condition on Fi and considering its approximation, we obtain (8.4.15). The wave speeds in solid and liquid phases are given by {ks/rsY^'^ and (ki/riY^'^, respectively. To have a global wave speed (I/TQ)^/^ in C , TQ > 0, independent of the phase, we define Ts = Toks] and n = Toki.

(8.4.21)


221

To obtain a weak formulation of the classical problem stated in (8.4.11)—(8.4.16), we consider the integral d f^^^MTl dt /{ dt\"

^ Q^j.^ ^ ^^j _ v2(i^(T))^ 0 dxdt.

(8.4.22)

Here, G, = G x (0,^,), 0 < ^ < ^* < oo, K{T) = KsT, if T < 0 and K{T) = KLT if T > 0, C{T) = CsT if T < 0, = CLT if T > 0, and 0 is the test function, 0 G C^(G'*). By adopting the procedure indicated in (5.2.12)—(5.2.14) it can be shown that

7

VK{T).N,

- {1(1 - 0 +

roj^K{T))N, 4> dxdt.

(8.4.23)

On using (8.4.11)-(8.4.16) in (8.4.23), we get

Wt {^"'^^w^+^^^^ ^ ^^)"" ^'(^(^)) = ''^+^^'' *-^- '"^ ^ -

(^•^•24)

Equation (8.2.24) is satisfied in G^ in the distributional sense. A pair of functions ( T , 0 such that T e W^^^{0,t,] L^G)) n L°^(0,t*; H^{G)), ^ e L'îG,) is called a generalized solution of the problem (8.4.11)-(8.4.16) and (8.4.17)-(8.4.19) if (8.4.24) is satisfied for a.a. t G [0,^*]. T{t) G H^(G) and ^(t) G Hg{T{t)) for a.a. t G [0,^,]; T(0) = To and (ToaA'(T)/at + C'(T) + ê)^_^ = 2Xo(a:). If F G iy^'°"(0,t*; //'HG')) (^"^ is the dual space of H^), then TodK{T)]dt + C'(T) + i^{t) G M/i'°^(0,t,; H~\G)) and the initial conditions are meaningful. Under suitable assumptions on F, To, ^{x,0) and Wo, existence of a unique generalized solution has been proved in [211]. A one-phase problem in which the melted ice first forms a mushy region with temperature zero and then becomes water with temperature greater than zero has also been discussed in [211]. The classical, weak and variational inequality formulations have been obtained for this one-phase problem. In terms of the freezing index the existence of the unique weak solution of the variational formulation has been discussed. An example of the non-existence of the generalized solution of a one-phase problem formulated with the above delay assumptions has been constructed in [211].

222


The one-phase multi-dimensional hyperbolic Stefan problem discussed in [224] consists of finding a hypersurface S{t) = {x e R^ : (pix.t) = 0}, 0 < ^ < oo, n > 1 and the temperature T(x,t) in G{t) = {x e R^ : (t){x,t) > 0}, 0 < t < oo, such that TCTU + CTt - KVT = 0, in G{t),

T ( x , 0 = 0, {l-^TCTt)<j>t =

(8.4.25)

] > on S{t) KVT-V(t).\

T{x,0) = To{x),

^

Tt{x,0) = T,{x),

\

(8.4.26)

(8.4.27)

S{0) = So = {x : (Pix.O) = (Po = 0}. ) This model in (8.4.25)—(8.4.27) is based on the delay assumptions of model III. The existence and uniqueness of H^- weak solutions were proved in [211]. The existence of the unique classical solution of the problem (8.4.25)—(8.4.27) has been proved in [224]. A solution (T, 0) of (8.4.25)-(8.4.27) is called classical if (T, 0) e CîBJ" x R\_). The above problem is called non-degenerate if VTo • V(/)o ^ 0, on S'o.

(8.4.28)

The condition (8.4.28) implies that the interface is really moving. We saw earlier that some compatibility conditions have to be satisfied at 5*0 for studying existence and uniqueness of solutions. The zeroth-order compatibility conditions on 5*0 are given by To(x) = 0,

] \ on 50. (/ + T C T i ) T i - A ' | V r o | ' = 0. J

(8.4.29)

The first-order compatibility condition on SQ can be obtained by comparing the two expressions for Tu on 5*0, one obtained from (8.4.25) and another from (8.4.26), and it is given by (/ -h 2TCTi){Ttt + VTi . fj) - 2KVTo • VTi + KV \Tof • //, (8.4.30) where fj=-Ti\/To\VTo\-\ The main result of [224] is the following proposition. Proposition 8.4.1.

Assume that the following conditions are satisfied :

(8.4.31)

8.4 Model III: Delay in the Response of Energy to Latent and Sensible Heats (i) (ii) (iii) (iv)

223

The problem (8.4.25)-(8.4.27) is non-degenerate. To(x), Ti(x) and <po{x) are sufficiently smooth. The compatibility conditions are satisfied on So up to the order 7 : 7 > {n-\-l)/2. The stability condition

is satisfied. Then there exists a ^0 > 0, such that in (0, ^0), there exists a unique classical solution (T,(/)) of (8.4.25)-(8.4.27) belonging to the space H''^' x H''^\0,to; Rl). The method of proof involves fixing the phase-change boundary by the hodograph transformation and then considering a linearized problem. By using the results of the linearized problem, the results for the nonlinear problem have been obtained. For / — 0, the stability condition (8.4.32) implies that the velocity of the interface should be less that the velocity of sound. For / 7^ 0, the condition (8.4.32) is stronger than the usual requirement that the phase interface moves slower that the sound speed. If the condition (8.4.32) is not imposed, then generally, one cannot expect the one-phase problem to be well-posed globally because of the hyperbolic wave property. It has been remarked in [224] that this condition is not satisfied at the time specified in the example considered in [211] to show the non-existence of the solution of the one-phase problem.

Chapter 9 Inverse Stefan Problems 9.1

Introduction

To understand the basic features of an inverse problem, which could be or not be a Stefan problem, we first consider a simple heat conduction problem of finding the temperature T(x, t) satisfying the following heat equation, and the initial and the boundary conditions. dT d^T — = -—,

(x,t) e Qt. = ^ X {0 < t < U < 00} , n = [0,1],

(9.1.1)

T(x,0) = 0, x G ^ ,

(9.1.2)

dT -—(0,^) = 0, 0S'

J sinh^ J^da

> Shmh'J^.

(9.2.12)

228

Inverse Stefan Problems

If ao > 0, we have ll/-/'ll>êxpy^.

(9.2.13)

Since —oo

The Classical Stefan Problem: basic concepts, modelling and analysis (North-Holland Series in Applied Mathematics and Mechanics)

The Classical Stefan Problem: Basic Concepts, Modelling and Analysis

Classical Complex Analysis (Pure and Applied Mathematics)

Classical Mechanics: Applied Mechanics and Mechatronics

Handbook of Applied Analysis (Advances in Mechanics and Mathematics)

Selected works in applied mechanics and mathematics

Practical Applied Mathematics Modelling, Analysis, Approximation

Practical applied mathematics: modelling, analysis, approximation

Practical Applied Mathematics: Modelling, Analysis, Approximation

Practical Applied Mathematics: Modelling, Analysis, Approximation

The Inverse Variational Problem in Classical Mechanics

Basic Concepts Of Mathematics

Soil Mechanics: Basic Concepts and Engineering Applications

Plastic Limit Analysis of Plates, Shells and Disks (North-Holland Series in Applied Mathematics and Mechanics)

Advanced Financial Modelling (Radon Series on Computational and Applied Mathematics)

Applied time series modelling and forecasting

Basic Concepts of Quantum Mechanics

Mathematics Applied to Continuum Mechanics (Classics in Applied Mathematics)

Mathematical Modelling: Classroom Notes in Applied Mathematics

Mathematical Modelling: Classroom Notes in Applied Mathematics

Thermodynamics and Statistical Mechanics (Basic Concepts In Chemistry)

Practical Applied Mathematics: Modelling, Analysis, Approximation (Cambridge Texts in Applied Mathematics)

Practical Applied Mathematics: Modelling, Analysis, Approximation (Cambridge Texts in Applied Mathematics)

Classical and New Inequalities in Analysis (Mathematics and its Applications)

Basic And Applied Thermodynamics

Applied Basic Mathematics, 2nd Edition

Applied Basic Mathematics (2nd Edition)

Functional Analysis (Pure and Applied Mathematics)

Complex Analysis (Pure and Applied Mathematics)

Classical Sequences in Banach Spaces (Pure and Applied Mathematics)

Mathematics Applied to Continuum Mechanics

The Classical Stefan Problem: basic concepts, modelling and analysis (North-Holland Series in Applied Mathematics and Mechanics)