Prepaint Specialties and Surface Tolerant Coatings

PREPAINT SPECIALTIES AND SURFACE TOLERANT COATINGS by Ernest W. Flick NOYES PUBLICATIONS Pal* Ridge, New kny, USA. ...

Author: Ernest W. Flick

154 downloads 4165 Views 22MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

PREPAINT SPECIALTIES AND SURFACE TOLERANT COATINGS

by

Ernest W. Flick

NOYES PUBLICATIONS Pal* Ridge, New kny, USA.

Copyright @ 1991 b y Ernest W. Flick No part of this book may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Library of Congress Catalog Card Number: 91-8702 ISBN: 0-8155-1273-2 Printed in the United States Published in the United States of America by Noyes Publications Mill Road, Park Ridge, New Jersey 07656 10987 6 5 4 3 2 1

Library of Congress Cataloging-in-Publication Data Flick, Ernest W. Prepaint specialties and surface tolerant coatings I by Ernest W. Flick. p. em. Includes index. ISBN 0-8155-1273-2 : 1. Primers (Coating) 2. Sealing compounds. I.Title. 1991 TP937.7.F55 667'.9--d~20 918702 CIP

To Another Hasty Generation Marlene Merando, Donald Harriman, Bruce Harriman Sr., William Smith Jr., Robert Smith, Howard Smith, Glenice Lear and James Taylor, Michael Taylor, Barbara LaGoy, Kenneth Taylor and Ann Elise Taylor and Eric Taylor and Janet Downing and Karen Lewia and Mark Taylor

V

Preface

This book describes more than 1500 currently available prepaint specialties and surface tolerant coatings. It has been compiled from information received from 67 manufacturers and distributors of these products. Specialty prepaint products and surface tolerant coatings make up a small, but growing segment of the paint and coatings industry. These products are particularly attractive to the do-it-yourself market and to small contractors. They also find use in the marine and transportation industries, and in the refinishingmarket. The products described in the book may, for example, prepare the surface for paint, thin the paint, allow painting over rusted areas, or provide quick and easy clean-up. They may be fillers, sealers, rust preventives, galvanizers, caulks, grouts, glazes, phosphatizers, corrosion inhibitors, neutralizers, graffiti removers, floor surfacers, etc. Substrates involved can be wood, metal, masonry, or asphalt. In some cases a specific product is described, in others a ''treatment'' involving a specific company's products may be indicated.

The data included represent selections from manufacturers' descriptions, in the manufacturer's own words, made a t no cost to, nor influence from, the makers or distributors of the materials. Only the most recent information has been included. It is believed that all of the products listed here are currently available, which will be of interest to readers concerned with product discontinuances. The book lists the following product information, as available, in the manufacturer's own words: (1 1

Company name and product category,

(2) Trade name and product number, (3) Product description including specifications, properties and applications, as presented by the supplier. Products are presented by company, and the companies are listed alphabetically.

vii

viii

Preface

Also included in the book are a Trade Name Index and a Product Type Index, for easy and rapid location of products by the reader. In addition, another section, which will be useful, contains Suppliers' Addresses. It can be found immediately following the Product Information section. My fullest appreciation is expressed to the companies and organizations which supplied the data included in the book. April 1990

Ernest W. Flick

NOTICE To the best of our knowledge the information in this publication is accurate; however, the Publisher does not assume any responsibility for the accuracy or completeness of, or consequences arising from, such information. This industrial guide does not purport to contain detailed user instructions, and by i t s range and scope could not possibly do so. Mention of trade names or commercial products does not constitute endorsement or recommendation for use by the Pub1isher. In some cases prepaint specialty products and surface tolerant coatings could be toxic, and therefore, due caution should be exercised in their application and use. Final determination of the suitability of any information or product for use contemplated by any user, and the manner of that use, is the sole responsibility of the user. We strongly recommend that users seek and adhere to a manufacturer's or supplier's current instructions for handling each material they use. The Author and Publisher have used their best efforts t o include only the most recent data available. The reader is cautioned to consult the supplier in case of questions regarding current availability.

Contents and Subject Index

PRODUCT INFORMATION Abatron, Inc. Structural Epoxies: Sealants ABOSEA L Advanced Materials GUARDCOTE Series 100 Air Dry Plastic Coating GUARDCOTE II Air Dry Plastic Coating PR IMECOTE Allied-Kelite Division Products for Metal Surface Preparation and Finishing Cleaners ISOPREP, KOOL-SPRA Y, PROCESS, KOOL SOAK, CHEMIDIZE, SUPER SOAK, KESONIC, KEYKOTE, SPRA-KLEEN Electrocleaners MUL TITEMP Rust and Scale Removers for Ferrous Metals SCAL E-OFF Aluminum Etchants and Additives for Caustic Aluminum DeoxidizerdDesmutters Chromate Conversion Coatings IRI DI TE Brighteners Corrosion Inhibitors RUST FOE, IRILAC Phosphate Conversion Coatings Phosphatizing Process Additives and Companion Products KESEAL Paint Booth Products KEFLOC

ix

1 2 2

3 3 4

5 6 6 6

7 7

8 8 8 9 9 10 11 12

x

Contentsand Subject Index Paint Strippers STRIPPER, COLD STRIPPER Alkaline Cleaners NIKLAD ALPREP, NIKLAD FERROPROEP Acid Cleaners Deoxidizer/Desmutter Acid Pickles and Activators NIKLAD MUL TIPREP Alvin Products, Inc. LAB-METAL Products LAB-SOL VENT, GAL VAX Cold Galvanizer Ameron AMERGUARD 148 Waterborne Acrylic Primer AMERGUARD 149 Waterborne Epoxy Primer AMERGUARD 335 Waterborne Epoxy Acrylic AMERLOCK 400 High-Solids Epoxy Coating AMERSHIELD Aliphatic Polyurethane Bartlett Chemicals, Inc. DOLPHIN BARTKOTE Beck Chemicals, Inc. Product Line BECKS Concrete Sealant MAGNA SEAL BECK'S RUST PREVENTATIVE OIL BOOTHWAX DRY BRUSH CLEANER ECONOST R IP EPOXYST R IP FERRO-BET #I 1 De-Rusting& Rust Passivating Agent FLEXTEMP FOYAL GRAFFITI REMOVER GRAFFITI EATER GR A FF ITI R ESISTO R KOROBEX KLEEN BOND "B" KLEEN PEEL Plastic Film LEX ISTR IP PA1NTOF F-I 60 RUST CONTROL OIL SI NTE R KOTE SPRAY GUN CLEANER VAPO-BAR Berlage Rust Proofing ANOGAL Big Three Industries, Inc. Aluminized BlOXlDE Rust Preventive Coating Weldable Primer M.A. Bruder & Sons Co., Inc.

12 13 13 13 13 14 14 15 16 16 17 18 19 20 21 21 22 22 22

22 22 23 23 23 24 24 24 25 26 26 27 27 28 28 29 29 30 30 31 31 32 32 33

Contents and Subject Index Exterior Coating Systems FRESH KOTE, LOK-TITE, SEA SHORE, RUST 0 LASTIC HYDRO-PRIME, PLY-TILE Interior Coating Systems RUST 0 LASTIC HYDRO-KOTE, LOC-TITE STAIN SEALER FRESH KOTE Enamel Undercoater (Alkyd) FRESH KOTE Exterior Primer FRESH KOTE Latex Exterior Primer High Performance (HIPAC) Systems RICH-LUX PRIME FAST Interior Coating Systems FRESH KOTE Alkyd Enamel Undercoater, FRESH KOTE Vinyl Primer, RICH-LUX Sealer Undercoater, RICH-LUX Wood Sealer, MlNlT DRI Clear Sanding Sealer, PL Y-THANE 540 Primer, OW 26 Floor Sealer, RICH-LUX Clear Wood Sealer, SEA SHORE Latex Primer MlNlT DRI Sanding Sealer PLY-MASTIC 101 Epoxy Mastic Coating (Epoxy-Polyamine) RICH LUX Enamel Undercoater (Alkyd) RICH-LUX Latex Enamel Undercoater (Acrylic Latex) R UST-0-LAST1C HYD RO-PRIM E RUST 0 LASTIC Vinyl Wash Primer SEA SHORE Latex Primer Samuel Cabot Inc. CABOT Stains PROBLEM-SOLVER Primer, PROBLEM-SOLVER Wood Cleaner, PROBLEM-SOLVER Wood Brightener Calbar, Inc. CALBEX Type P NATIONAL TINNERS Paints SHOWER-PROOF, TIN-0-LIN California Chemical Co. Heavy Duty STRIP California Products Corp. Acrylic Enamel Undercoat ALLWALL Vinyl Acrylic Latex Flat CAL GLAZE Block Filler House Paint Primer Acrylic Latex KOTALL Alkyd Primer-Sealer LACRYLIC Acrylic Lacquer Clear Masonry Sealer LARCOLOID Alkyd Enamel Undercoat LARCOLOID Zinc Chromate Primer PLEXICOLOR Acrylic Silica Block Filler PRO PAINT Flat Latex SAFETY PRIME House Paint Primer Spray Paints Primer/Finish STONITE Primer: Interior/Exterior-Acrylic Lacquer-Sealer STORM STAIN Universal Wood Primer Oil Base

xi 33

34 35 36 37 38 40

43 44 46 47 48 49 50 51 51

53 53 54 55 55 56 56 57 58 59 60 61 62 63 64 65 66 67 68 69

xii


STORM STAIN Primer Acrylic Latex Vinyl Primer-Sealer WILBUR & WILLIAMS CLEAR SEAL Coating WILBUR &WILLIAMS COMBATIT 1050 Red/lO51 Gray Metal Shop Primer WILBUR & WILLIAMS Enamel Undercoat Acrylic Latex WILBUR & WILLIAMS FRIGID COATWW4800 White Cold Storage Gloss Enamel WILBUR & WILLIAMS GRIP-COAT 6906 Vinyl Wash Primer WILBUR &WILLIAMS MASON-COTE Sealer 7010 Masonry Conditioner WILBUR &WILLIAMS PRIME LINE 1703 Red/1704 Gray Universal Metal Primer WILBUR &WILLIAMS PRIME LINE 1705 Heavy Duty Metal Primer WILBUR &WILLIAMS PRIME LINE 1706 Metal Primer WILBUR &WILLIAMS Red Shop Primer 5512 Red Oxide Metal Primer WILBUR &WILLIAMS RUST NEUTRALIZER 1056 Urethane Emulsion WILBUR &WILLIAMS RUST-STOP 1046 Latex Metal Paint WILBUR & WILLIAMS RUST-STOP 1067 Red/lO61 White Acrylic Latex Metal Primers WILBUR &WILLIAMS TOTALUME 2605 Bright Aluminum WILBUR &WILLIAMS ZINC SHIELD 5700 Zinc Rich Primer SSPC Preparation Chart Carboline CARBOLINE 03358 Single Component Water-Borne Acrylic Primer CARBOLINE 801 Two-Component, Cross-Linked Epoxy CARBOMASTIC 15 Low Odor CoatingsKomposites Conductive FlBR E/CRETE: 2033-2043-2143 Electrically Conductive Floor Surfacer and Lining CONO/GLAZE 286 Acid Resistant Protective Coating CONO/GLAZE 2010 Sanitary, Tile Like, Solventless Coating CONO/G LAZE 2020 Chemical Resistant, Solventless Coating CONO/GLAZE 2070 Lining Concrete and Steel CONO/GLAZE 2220 Heat and Chemical Resistant, Solventless Coating CONO/GLAZE 2350 Topcoat for €pox y Toppings CONOIG LAZE 251 0 Sanitary, Tile Like, Architectural Coating

70 71 72 73 74 75 76 77

78 79 80 81 82 83 84 85 86 87 89 89 90 91 92 93 94 95 96 97 98 99

Contents and Subject Index CONOWELD 5013 Conductive Primer FIBRE/CRETE MORTAR 121 Aggregate Filled Fibre-Reinforced Floor Surfacer FIBRE/CRETE 122 Aggregate Filled Fibre-Reinforced Floor Surfacer FIBRE/CRETE 210 High Build Reinforced Flexible Coating FIB R E/CR ETE 285 High Build Reinforced Acid Resistant Coating F IBRE/CR ETE 2030 Chemical and Abrasion Resistant Coating FIB R E/CR ETE 2040 Chemical and Abrasion Resistant Coating FIBREKRETE 2060 Dilute Chemical and Heavy Abrasion Resistant Coating FIBRE/CRETE 2140 Moderate to Harsh Chemical and Abrasion Resistant Coating FIBRE/MENT 124 Steel Fibre-Reinforced Modified Cement Mortar HYGRIP 1630,1640,1660 Epoxy Coating PRETREATMENT 512 Adhesion Promoter Composition Materials Co., Inc. PLASTI-GRIT CLEAR-CUT Crest Industrial Chemicals, Inc. Products ACID CLEANER #1, PCC-6 Aluminum Conversion Coating, GAL V-A-PAINT Crown Industrial Products Co., Inc. CROWN Industrial Aerosol Spray Paints 81 Coatings DURA-PRIME Non-Chromate Primer KLEER KOTE DAP Inc. DERUSTO Rust Preventive Enamel with Built-In Primer GAL V-A-GRIP, C-GLO, EASE-IT Silicone Spray, TOPS Roof Coating, Rust Preventive Primers, MINUTE-SOL V Thinner High Temperature Enamels BROMA, HEAT MASTER James B. Day & Co. DACONITE Industrial Finishes KUT-KOTE Liquid Paint and Varnish Remover, NO-FLAME Paint and Varnish Remover, DACONITE Semi-paste Alkyd Wood Filler, DIP STRIP Dipping Remover, DA YCO Liquid Brush Cleaner, DA YCO SCUFF Surface Preparation Deglosser, PRESTO SEAL First Coater, DASOL Alcohol Solvent,

xiii 100 101 102 103 104 105 106 107 108 109 110 111 112 112 113 113

116 116 117 118 119 119

123 124 124

xiv

Contentsand Subject Index DA YCO Semi-paste Wood Filler (Alkyd), LEM-0-OIL Polish, DACOTHANE Sanding Sealer, COVERSOL (Heavy Duty Flat White Primer-Sealer) Detrex Corp. Product Data Immersion Cleaners-Ferrous Spray Cleaners-Ferrous lmmersion Cleaners-Non-Ferrous Spray Cleaners-Non-Ferrous Pre-Soak Cleaners Electrolytic Cleaners Emulsion Cleaners Activated Paintbond Cleaners Paint Strippers Spray Booth Coatings VINCO TE DefloccuIant s Neutralizers Miscellaneous Specialties Acidulated Rinses REXOL ENE Immersion Iron Phosphate Immersion Zinc Phosphates MICROBOND Spray Zinc Phosphate Zinc Paintbond Accelerators Spray Calcium Phosphate Spray Powdered Iron Phosphates PAINTBOND Spray Liquid Iron Phosphates Rustproofing Immersion Phosphate Coatings PERM-CO TE Rustproofing Oil PERM-OIL Acid Detergents Aluminum Conversion Coatings Extrusion Phosphates EXTRUDICO TE Rolling Oils Drawing Compounds Synthetics CROWN DRAW Corrosion Rust Preventives Corrosion Package Specialty Metal Cleaners Emulsion Base Cleaners and Corrosion Inhibitors Solvent Based Corrosion Inhibitors Oil Based Corrosion Inhibitors PrimerdMetal

127 127 127 127 127 127 128 128 128 128 128 128 128 129 129 129 129 130 130 130 130 130 131 131 131 131 132 132 132 132 133 133 133 133 133 133 134


Primers/Plastics Engine Enamel Chassis Blacks Striping Lacquers and Enamels Material Handling Coatings Miscellaneous Specialty Coating Devoe Coatings Co. BAR-RUST 235 Multi-Purpose Epoxy Coating BAR-RUST 236 Multi-Purpose Epoxy Coating PRE-PRIME 167 Rust Penetrating Sealer Dolphin Paint & Chemical Co. DOLCHEM 6010/6011/6015 Air Dry Body Sealants DOLCHEM 6016 Level Putty DOLCHEM 6020 Series Elastomeric Sealants DOLCHEM 6035/DOLCHEM 6036/DOLCHEM 6037/DOLCHEM 6038 Low Viscosity Elastomeric Adhesive/Sealants DOLCHEM 6060 Series Fast Dry Body Sealants DOLCHEM 6065 Heat Resistant Sealant DO LCHEM 6066/DO LCHEM 6067 Elastomeric Adhesive/Sealants DO LCHEM 6068/DO LCHEM 6069 Exterior Body Sealants DOLCHEM 6070/DOLCHEM 6071/DOLCHEM 6072 Anti-Corrosion Sealants DOLCHEM 6094 Insulating Thumbing Putty DOLCHEM 6095 ThumbgradeSealer DOLCHEM 6096 Aluminum Lap Joint Sealant DOLCHEM 6010/6011/6015 Air Dry Body Sealants DOLCHEM 6098 High Thix Weld Through Sealant DOLCHEM 6099 Epoxy Urethane Anti-Corrosion Sealant DOLCHEM 6100 Plastisol Structural A dhesive/Sealant DOLCHEM 61 IO/DOLCHEM 61 15 Plastisol Body Sealants DOLCHEM 6200 Series Acrylic Latex Sealants DOLCHEM 6451

xv

134 134 134 134 134 134 135 135 136 137 138 138 139 140

140 141 142 143 144 145 146 146 147 148 149 150 151 152 153 154

xvi

Contents and Subject Index Clear, Fast Dry, Adhesive/Sealant DOLCHEM 6520 Series Elastomeric Sealants DOLCHEM 6623 Electrostat Enamel DOLCHEM 6626 Machinery Enamel DOLCHEM 6640 Exterior Paint DO LCHEM 6694 WELDTHRU ROX Primer DOLCHEM 6800 Series Flexible Paints for Rubber DOLCHEM 6828 Anti-Corrosion Coating DuPont Maintenance Finishes CORLAR 825-007 Fast Dry Primer CORLAR 825HB High Build Chromate Free Epoxy Primer 825-Y-9031 DULUX 67-Y-834 Chromate Free Primer (VOC Conforming) DULUX 681 FD Chromate Free Primer (VOC Conforming) DUPONT 25P High Solids Epoxy Mastic GANlClN 347-Y-912 Inorganic Zinc-Rich Coating GANlClN 347-Y-931 Inorganic Zinc-Rich Coating IMRON 62 Polyurethane Primer Dutch Boy Paints CONFIDENT Exterior Latex Primer CONFIDENT Exterior Oil/Alkyd Wood Primer CONFIDENT Interior Latex Wall Primer CONFIDENT Interior OiI/Alkyd Wall &Wood Primer DIRT FIGHTER Exterior Latex Primer DIRT FIGHTER Exterior Oil/Alkyd Wood Primer DIRT FIGHTER Interior Latex Wall &Wood Primer DIRT FIGHTER Interior Oil/Alkyd Wall 81Wood Primer DIRT FIGHTER Latex Universal Primer DIRT FIGHTER Oil/Alkyd Masonry Conditioner Interior Latex A L L PREP Interior Varnish Sanding Sealer Professional Architectural Exterior Oil/Alkyd Wood Primer Professional Architectural Interior Latex Wall Primer Professional Interior/Exterior Architectural Latex Block Filler RUST BEATER Interior/Exterior Oil/Alkyd Metal Primer Flame Control Coatings, Inc. FLAME CONTROL No. 6 Clear Wood Sealer FLAME CONTROL No. 850 Series FLAME CONTROL Special Non-Flammable Paint Stripper No. 11 FLAME-GLAZE 9922 Two Part Epoxy Primer The Flood Co.

155 156 156 157 158 159 160 161 161 162 163 164 165 166 167 168 169 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 185 186 187 187 188

Contents and Subject Index VIP TER-POLYMER SEALANTS #5000 Series VIP 1000 Waterborne Surface Conditioner VIP 1200 Acrylic Alkali Resistant Surface Conditioner VIP 1600 Clear Asphalt Sealer Products E-B EMULSA-BOND, PENETROL Aluminum, E.S.P.-EASY SURFACE PREP, SEASONITE Stabilizing Treatment The Glidden Co. GLIOOEN Protective Maintenance Coatings Alkyd Finishes GLID-GUARD, ULTRA-HIDE, SPRED ULTRA, SPRED LUSTRE Coal Tar EPOXY GLID-GUARD GLID-TILE, GLID-GUARD METALLITE Chemical Cleaning Restoration Products UL TRA-KLEEN Primers for Gypsum Board/Plaster Surfaces SPRED ULTRA, SPRED SATIN, U L TRA-HIDE, INSUL-AID Primers for Wood Surfaces GLIDDEN Other Primers Primers for Masonry/Concrete and Block/Cement Surfaces Primers for Metal Surfaces GL ID-GUAR D RUSTMASTER, GL ID-GUAR D VIN YL-COTE, GL ID- THANE ONE Insl-X Products Corp. CHECKRUST Chemical Resistant Primers SPEEDY METAL PRIMER, FISH OIL PRIMER, UNIVERSAL, INSL-TILE, GAL VIN-X, RUSTARRESTOR CHECKRUST Finish Coats INSTANT ENAMEL, INSTANT METAL COAT Primers-Sealers-Stainkillers INSL-LAC, AQUA LOCK Electrostatic Coatings ELECTROKOTE Epoxy Coatings AQUA- TILE Food and Beverage Industry Coatings FREEZERKOTE, SUPER DAMPWAL L Gloss Enamel, DAMPWALL UNDERCOATER Heat Resistant Coatings INSLUME Industrial Colorants CHROMA-CHEM Reducers for INSL-X Coatings INSL-TRON Polyurethane Coatings

x vii 188 189 190 191 192

193 193 193

196 200 205 206 207 208 209 21 1

219 219

222 223 224 225 226

227 228 228 229

xviii


INSL- THANE, GRIP-X, INSL- TRON Accelerator, INSL- TUFF lntex Chemical, Inc. Metal Cleaners INTEX Paint Removers Rust Preventatives " N U T BUSTER Rust Removers Jones-Blair Co. Aluminum Asphalt Base Aluminum Bright Finish-Supreme Aluminum Brilliant Finish Aluminum Super Speed CHEM-0-CONE Heat Resistant Coatings CHEM-0-LITE Chemical Resistant Vinyl CHEM-0-LITE Primer CHEM-0-LITE Vinyl Colors CHEM-0-PON High Solids, High Build Epoxy Primer CHEM-0-PON Zinc Chromate Epoxy Primer CHEM-0-THIX High Build Vinyl HEAT-BAN 5185 White Heat Resistant Aluminum MIST COAT II Vinyl Wash Primer MULTI-GRIP Acrylic Latex Primer MULTI-PURPOSE Primer RUST-NOT Metal Primer White RUST-NOT Metal Primer Red-Brown STANTEST Red-Brown Oxide Primer UNI-FLEX Architectural Textured Coating UNIVERSAL VINYL Primer Kop-Coat, Inc. BITUMASTIC Black Solution BITUMASTIC C.T. Urethane-Type I BITUMASTIC NO. 300-M BITUMASTIC No. 300-M High Build BlTUMASTlC SUPER SERVICE Black KOP-COAT Aluminum Epoxy Mastic KOP-COAT Concrete and Masonry Filler KOP-COAT P-I 500 Inorganic Zinc KOP-COAT 40 PASSIVATOR KOP-COAT 340 Gold Primer KOP-COAT 610 Acrylic Emulsion KOP-COAT 620 Acrylic Emulsion KOP-COAT 622-LCF Primer Lion Oil Co. LION D200 Elastomeric Sealant LION D203 Two-Component Elastomeric Vertical Joint Sealant

231 231 232 236 239 242 242 243 244 245 246 247 248 249 250 25 1 252 253 254 255 256 257 258 259 260 261 262 263 263 264 265 266 267 268 269 270 27 1 272 273 274 275 276 276 277


xix

NOKORODE LION SP Asphalt NOKORODE LION 331 Loctite Corp. . EXTEND Rust Treatment LPS Laboratories, Inc. LPS COLD GALVANIZE LPS3 Heavy-Duty Rust Inhibitor LPS Instant Cold Galvanize LPS Paint and Gasket Remover Mantrose-Haeuser Co. Galvanized Metal Primer HIDE 'N SEAL Quick-Dry, Oil-Based, All-Purpose Primer for Super Stain Sealing MAXHIDE Water-Based Primer, Sealer, Stain Killer ENAMELAC Flat White, Shellac-Based Primer, Sealer, Stain Killer READY PATCH Ready-to-Use Spackling and Patching Compound READY PATCH LITE Professional Spackling and Patching Compound SANDING WOOD SEALER Wallcovering Preparations McGean-Rohco, Inc. INTERLOX Iron Phosphate Systems INTERLOX Zinc Phosphate Systems NORTHWEST Cleaners Spray Cleaners, Immersion Cleaners Paint Strippers Metalbrite Products Corp. METALBRITE Rust Remover and Inhibitor Mohawk Finishing Products, Inc. Factory Edgers Benjamin Moore & Co. Alkyd Enamel Underbody 247 AI kyd Primer Sealer 246 Block Filler 145 Damp Surface Primer 205 Epoxy Rust Inhibitive Primer 1 1 : Epoxy Hardener (Curing. .jent) 177/Epoxy Thinner 178 IRONCLAD Exterior Primer 140 Galvanized Metal Latex Primer 155 MOORE'S Alkyd Masonry Sealer 077 MOORE'S Alkyd Primer Sealer 200 MOORE'S Interior Wood Finishes Quick Dry Sanding Sealer 413 MOORE'S Latex Exterior Primer 102 MOORE'S Latex Quick Dry Prime Seal 201 MOORE'S QD 30 (202)Aerosol Spray 491 MOORE'S Speedy Primer Sealer 340 MOORWHITE Primer 100

278 279 280 280 281 281 282 283 284 285 285 285 286 286 287 287 288 288 289 289 291 293 294 295 295 296 296 297 297 298 299 300 301 303 304 305 306 307 308 309 310 31 1 312

xx

Contents and Subject Index Quick Dry Industrial Rust Inhibitive Primer 168 RETARD-X Rust Inhibitive Latex Primer 162 Sanding Sealer Clear 253 Vinyl Latex Primer Sealer 252 WALL-GRIP 1 , 2 , 3 (203) 660 Solvent Thinner 293 National Solvent Corp. Paint Remover &Wood Refinishers Paint Thinners & Solvents The Naval Jelly Co. Naval Jelly Ocean Coatings FLAYMBAR Intumescent and Fire Retardant Paints OCEAN, OCEAN TY-COAT Peterson Chemical Corp. Heavy Duty Epoxy Resin Paint #2 LSC Primer #3 Block Filler #4 Undercoat #5 Primer #8 Primer #I 0 Sealer Phillip Brothers Chemicals, Inc. SUPERCHLON 8228 Chlorinated Polyolef in Poly-Carb Concrete Treatments: MARK-I21 to MARK-145 Sealants: MARK-261 to MARK-280 Maintenance Coatings PPG Industries, Inc. Interior: Dry Wall: Normal Use and Atmospheric Conditions SPEEDHIDE, SPEEDCRAFT, PITTSBURGH, WALLHIDE, SPEEDPRO, HIDE-A-SPRAY, SATINHIDE, SUPER TECH, PITT-GLAZE interior: Plaster: Normal Use and Atmospheric Conditions Interior: Plaster: Hard Service Areas Interior: Masonry Walls: Normal Use and Atmospheric Conditions SPEEDWHl TE Interior: Masonry Walls: Hard Service Areas Interior: Painted Woodwork and Trim: Normal Use and Atmospheric Conditions (Not Floors). R i m , Non-YieldingSurfaces MANOR HALL Interior: Painted Woodwork and Trim: Hard Service Areas (Not Floors). Firm, Non-Yielding Surfaces Interior: Painted Wood Floors and Steps: Normal Use and Atmospheric Conditions Interior: Painted Heavy Duty industrial Wood Floors: Hard Service Areas AOUAPON

313 314 315 316 317 318 31 9 319 320 322 322 323 323 334 334 337 338 339 340 34 1 342 343 343 344 344 345 345 346 346

35 1 354 355 359 360 363 364 364


xxi

Interior: Woodwork and Trim: Normal Use and Atmospheric 364 Conditions REZ Interior: Woodwork and Trim: Normal Use and Atmospheric Conditions: Stained and Varnished Finishes. New Softwood or 365 Plywood Interior: Woodwork and Trim: Normal Use and Atmospheric 366 Conditions: Natural Finish: Close Grained Woods Interior: Wood Floors and Steps: Normal Use and Atmospheric 366 Conditions 367 Interior: Heavy Duty Industrial Wood Floors: Hard Service Areas Interior: Concrete Floors: Normal Use and Atmospheric 367 Conditions LEPTYNE 368 Interior: Painted Concrete Floors: Hard Service Areas 368 Interior: Ferrous Metal: Normal Use and Atmospheric Conditions MUL TIPRIME Interior: Galvanized Metal: Normal Use and Atmospheric 372 Conditions 374 Interior: Galvanized Metal: Hard Service Area POL YCLUTCH 376 Interior: Aluminum: Hard Service Areas 377 Interior: Aluminum: Normal Use and Atmospheric Conditions Interior: Industrial Machinery: Normal Use and Atmospheric 378 Conditions LA VAX Exterior: Painted Wood Siding, Rustic Wood Shakes and Shingles: 379 Normal Use and Atmospheric Conditions SUN-PROOF, PERMANIZER PLUS 381 Exterior: New and Previously Painted Plywood Siding SPEEDPRO Exterior: Hardboard Siding: Normal Use and Atmospheric 383 Conditions Exterior: Wood Decks and Porches: Normal Use and Atmospheric 384 Conditions Exterior: Painted Wood Trim, Doors and Shutters: Normal Use and 385 Atmospheric Conditions Exterior: Natural or Stained Wood-Redwood and Cedar Siding, Wood Shingle Roofs (Stained): Normal Use and Atmospheric Conditions 386 Interior: Ferrous Metal: Hard Service Areas 388 Exterior: Cement-Composition Siding and Panels: Normal 389 Atmospheric Conditions Exterior: Masonry Walls: Normal Use and Atmospheric Conditions 390 Exterior: Concrete Patio and Breezeway Floors: Normal Use and Atmospheric Conditions 391 Exterior: Ferrous Metals-Structural: Normal Use and Atmospheric Conditions 392 Exterior: Concrete and Asphalt Roads, Driveways, Parking Lots, Etc.: Normal Use and Atmospheric Conditions 393

xxii


Exterior: Galvanized Metal: Normal Use and Atmospheric Conditions Exterior: Vinyl or Aluminum Siding: Repaint Work: Normal Use and Atmospheric Conditions Exterior: Aluminum Metal Surfaces: Structural: Normal Use and Atmospheric Conditions Randolph Products Co. MI L-SPEC Paints RAN TI TE Red Devil, Inc. Cartridge, Aerosol and Tube Products Caulks SPEED DEMON, LIFETIME Caulk, Grout, Adhesives, Sealers and Cleaners Fillers, Cleaners & Maintenance Products Cyanoacrylate Super Glue, Contact Cement, SA V-A-BRUSH Brush Restorer Powder, TSP-90 Heavy-Duty Powdered Cleaner, Garage and Driveway Powdered Cleaner, WAXOFF, Powdered Floor Cleaner, Aggregate Textured Finish Additive, Tack Cloth Sealants CELL ULON Spackling, Glazing Compounds and Fillers ONETIME, PATCH N ' F I L L Specialty Repair Cartridge Items Fireplace & Stove Repair, Stucco & Cement Repair, Gutter & Lap Seal, Blacktop and Roof Repair, Concrete and Mortar Repair, Panel and Construction Adhesive, Acrylic Panel and Construction Adhesive Red Spot Paint & Varnish Co., Inc. Automotive CHROMEBOND, DESOFLEX Business Machines ATTENULAC Vacuum Metallizing/UV Specialty Coatings NEXTEL Rust-Oleum Corp. Heat Resistant 4100,4200,4300 Systems ZINC-SELE Heavy Duty Epoxy 9300 System . High-Build Epoxy Finishes 9500 System LABOR SAVER High Performance Epoxy 9100 System LABOR SAVER Industrial Enamel System LABOR SAVER HARD HAT Industrial Aerosols LABOR SAVER RUST REFORMER 3575 LABOR SAVER 108 CLEAN AND ETCH Solution LABOR SAVER 3599 All Natural Cleaner/Degreaser LABOR SAVER 8400 Food and Beverage Industry Coatings

394 396 398 399 399 400 400 400 40 1 402

403 404 405

406 406 42 1 425 438 440 440 44 1 442 443 444 445 445 446 447 448


xxiii

448 SPEEDY DRY Coatings 1500 System 449 Primers Industrial Enamels, Waterbase, Epoxy, Heat Resistant, Universal/Specialty 455 RUST-OLEUM LABOR SAVER 456 RUST-OLEUM LABOR SAVER: Industrial Floor Coating System 457 RUST-0LEUM Water-Based Epoxy 5300 System 458 RUST-0-THANE9400 System Polyurethane 459 RUST REFORMER 460 Special Performance Products SUR FA-ETCH 463 Water-Based Systems RUST-0-CR YLlC 464 Chemical Resistance Guide Alkyds, Water Base Acrylic, Epoxies, Urethane, Zinc, Vinyl, Heat Resistant 466 Stan Sax Corp. 466 MGIP-297 Corrosion and Rust Inhibitor 466 MSPL-246 TAGO-MITE Acidulated Rinse-Phosphate Systems 467 MSR L-120 Rust Remover and Metal Conditioner 467 MSR L-23 Rust Remover and Metal Conditioner 468 MSRP-323 Alkaline Deruster & Phosphate Coating Stripper MSRP-1005 Alkaline Deruster & Descaler Phosphate Coating Stripper 469 470 MSWP-203 Spray Booth Water Curtain Compound 47 1 PRP-72 Paint Stripper 472 Sentry Chemical Co. 472 RUST RIP Rust Remover and Phosphatizer 472 RUSTOP Rust Convertor 473 The Sherwin Williams Co. 473 Direct-to-MetalEnamel 474 DTM Acrylic Gloss Coating: Water Reducible 475 DTM Acrylic Primer/Finish 476 Epoxy Mastic Aluminum 477 Epoxy Mastic Coating 478 Galvite Paint White 479 Heavy Duty Block Filler 480 HI-61LD Chlorinated Rubber Primer 48 1 HI-BI LD Vinyl Primer 482 Industrial Enamel 483 Industrial Enamel VOC Complying 484 Industrial Water Based Acrylic Paint 485 KEM A & A Epoxy Primer 486 KEM CATI-COAT Epoxy Filler/Sealer 487 KEM KROMIK Metal Primer 488 KEM KROMIK Universal Metal Primer 489 KEM MATRIX Primers 490 KROMIK Metal Primer 491 Latex Metal Primer

xxiv

Contentsand Subject Index

METALASTIC II Enamel METALTEX Semi-Gloss Coating Recoatable Epoxy Primer Silicone Alkyd Enamel Tank Chalking White TILE-CLAD II HI-BILD Epoxy Primer Universal Metal Primer Water-Based Catalyzed Epoxy Primer Zinc Chromate Primer ZINC CLAD IV Somay Products, Inc. Pre-Paint Coatings SOMA Y Primers/Undercoaters/Sealers STA Y-WHITE Steelcote Manufacturing Co. CORITE Block Filler DMAP-TEX A&A Sealer and Undercoater DAMP-TEX 110 Enamel EPO-LUX 100 E-14 Zinc Rich Zinc Dust Primer EPO-LUX 100, E-20 Basic Lead Silico-Chromate Primer EPO-LUX 100, E-25 Primer HALTS-RUST HR 1-2-3 Primer HALTS-RUST HR-54 Zinc Rich Primer HALTS-RUST Primers INZINC MK II MCU 2100 Type V Zinc Rich Primer Low V.O.C. SPEEDEPOXY STEELCOTE CLEAN & ETCH Sterling-Clark-Lurton Corp. Caulking Cornpounds STERLING FIMYL-SEAL, AQUA CAULK, STERLING, BUTAC, SUPERB, STER-BOND Glazing and Patching Compounds AQUA-GLAZE, OLD TIME, SPATCH-PATCH, SPATCHPATCH LIGHT, JOINT COMPOUND Primers & Sealers, Paints PRIME-IT, STAIM-SEAL, OLDE YANKEE TOWNE Removers, Refinishers, Cleaners, Deglossers LIQUI-STRIP, SANDING LIQUID, FURNITURE REFINISHER Sunnyside Corp. Paint Solvents & Thinners Turpentines Specialty Solvents & Chemicals Cleaners, Removers 8t Sealers 3M Co. Chemicals

492 493 494 495 496 497 498 499 500 50 1 502 502 503 505 505 506 507 508 509 510 51 1 512 513 514 515 516 517 518 518

519

520 52 1

522 522 522 523 523 524 524

Contents and Subject Index 3M Rocker Panel Spray, 3M WELD-THRU Coating, 3M Brand FINESSE-IT lI Finishing Material, 3M SUPER PANEL FILLER, 3M PREP-TEAM Liquid Compound, 3M PREP-TEAM, 3M PREP-TEAM Liquid Polish, 3M PREP-TEAM Natural Gloss Vinyl and Rubber Dressing, 3M PREP-TEAM All Purpose Cleaner, 3M Machine Rubbing Compound, 3M Super Duty Rubbing Compound, 3M Super Duty Paste Compound, 3M ACRYL-GREEN Spot Putty, 3M SUPER RED Putty, 3M FILL 'N GLAZE-Pink, 3M FINAL GLAZE, IMPERIAL Hand Glaze, IMPERIAL Machine Glaze, IMPERIAL Micro finishing Glaze Coating and Sealer Products 3M ULTRA PRO, 3M FLEXICLEAR, 3M ALL-AROUND, 3M FAST 'N FIRM, 3M HEA VY DRIP-CHECK Products AUTO-PAK Professional Formula Spot Putty, AUTO-PAK Power Rust and Paint Stripper, RUST A VENGER Rust Convertor, NEW AGAIN Body Repair System SCOTCHKOTE 134 Fusion Bonded Epoxy Coating SCOTCHKOTE 136 Fusion Bonded Epoxy Coating SCOTCHKOTE 203 Fusion Bonded Epoxy Coating SDTCHKOllE2LKN Fusianhnded b ~ &tin$ v SCOTCHKOTE 213 and 214 Fusion Bonded Epoxy Coatings SCOTCHKOTE 213 Spray Grade/SCOTCHKOTE 214 Spray Grade Fusion Bonded Epoxy Coatings SCOTCHKOTE 213PC and 214PC Patch Compounds SCOTCHKOTE 206P Hot Melt Patch Compound SCOTCHKOTE 302,309, and 312 Liquid Epoxy Coatings SCOTCHKOTE 306 Liquid Epoxy Coating Titan Laboratories 01L-FLO Safety Solvent Cleaner & Degreaser Tnemec Co., Inc. Series 135 CHEMBUILD High-Build, High-Solids Catalyzed Epoxy Coating 50-330 POLY-URA-PRIME Moisture-Cured Urethane Primer United Solvents of America, Inc. Paint Removers-Turpentine-LinseedOil AME RI-STRIP, A ME RI-CUT, AME RI-PEEL, A ME RI-MO VE Solvents Thinners U.S. Polychemical Corp. Hard Surface Cleaners: Water Based Products POL Y-SPRA Y JET, TROPICLEAN, SAMSON, PERFECT WA Y Hard Surface Cleaners: Solvent Based Products QUlK SQEEZ, POL YCHEM Hard Surface Cleaners: Specialty Products POLY RUST REMOVER, DEE-FENSE WCC Industries Inc.

xxv

527

528

529 530 53 1 532 533 534 535 535 536 537 538 538 539 539 540 54 1 54 1 543 545 547 547 549 550 55 1

xxvi


MAINTZ HYPALON Coatings 551 MAINTZ Maintenance Free Architectural Coating 552 MAINTZ N-1001 554 555 Wisconsin Protective Coatings Corp. PLASITE Coatings 555 Modified Epox y-Cold Sets, Inorganic, Vinyl Esters, Baked, U. V., High Build Coal Tar Epoxy, Aluminum Epoxy Mastic, Primer, Heavy Build Self-priming Epoxy, Hopper Car Lining, HiResistant Metal Primer, Modified Epoxy Hi- Resistant Protective Coating, Modified Epoxy Mastic Hi-Resistant Protective Coating, High Build Self-priming Epoxy, Heat Resistant Aluminum, Caulking Materials Compounds, Caulking/Filler Compound, PLASTI-ZINC Inorganic Protective Coatings, Sealer, Organic Zinc-Rich Primer, Heavy Duty Exterior Coating, Aliphatic Polyurethane Coating, Hi-Build Vinyl, Vinyl Heavy Duty Coatings, High Bake Phenolic Coating, Vinyl Ester Heavy Duty Resistant Coating, Vinyl Ester Heavy Duty- Thick Film High-Resistant Coating, Conductive Coating, Chemical Resistant Monolithic Floor Surfacer, Chemical Resistant Monolithic Liner, Grout, Chemical Resistant Laminated Monolithic Floor Topping, Electrically Conductive Monolithic Floor Surfacer, Low Temp Cure Protective Coating, Heavy Duty Primer-Hi-Resistant Anti-Corrosive Primer, Hi-Resistant Heavy Build Protective Coating, Organic Zinc Primer, Heavy Build Inhibitive Primer Xymax Inc. 593 MONO-GARD Single Component Moisture-Cured Polyurethane Coating 593 MONO-ZINC Zinc Rich Moisture-Cured Polyurethane Primer/ Topcoat 594 SUPPLIERS' ADDRESSES

595

TRADE NAME INDEX

60 1

PRODUCT TYPE INDEX

61 1

2

Prepaint Specialties and Surface Tolerant Coatings

Product Information ABATRON, INC.:

Structural Epoxies: Sealants:

ABOSEAL 8104-16:

Most versatile architectural acrylic sealant. 1 0 0 0 % elongation. White or custom colors. Uses, Applications: Construction, industrial and marine sealing. For walls, windows, floors, enclosures, ceilings, transportation. Technical Support Specs.: One part. 80% solids. Shore A 40. Elongation 1000%. 16 psi tensile strength. Excellent adhesion to wood, metal, glass. Installation Characteristics: Apply with putty knife or caulking gun on cleaned and sound surfaces. 24% shrinkage. No slump.

ABOSEAL 8104-20: The only acrylic sealant meeting FED IT-S-00230C Class A. White or custom colors. Uses, Applications: Construction, industrial and marine sealing. For walls, windows, floors, enclosures, ceilings, transportation. Technical Support Specs: One part. 90% solids. Shore A 25-40. Elongation 400-600%. 40-60 psi tensile strength. FED TT-S-00230C Class A. Installation Characteristics: Apply with putty knife or caulking gun on cleaned and sound surfaces. 10% shrinkage. No slump. Excellent adhesion. ABOSEAL 8104-8:

Polysulfide standard f o r the highest architectural specifications. No slump. Brown, black or other dark colors. Uses, Applications: For the highest requirements in construction, industrial and marine environments. Sealing windows, walls, hulls, bulkheads, decks, floors, enclosures. Technical Support Specs.: 2 parts. 100% solids. Ratio: 10015.7. 2 hrs. tack-free. Shore A 30-35. Elongation 300-350%. 200-250 psi tensile. FED TT-S-00227-E. Installation Characteristics: Apply with putty knife or caulking gun on cleaned and sound surfaces. No shrinkage. No slump. Superior adhesion. Custom versions available.

Advanced Materials 3

ADVANCED MATERIALS: GUARDCOTE Series 100 Air Dry Plastic Coating that is both Acid and Alkali Resistant: An air dry plastic coating that resists acids and alkalis at temperatures up to 180F. Available in eight colors to accomodate color coding. Coverage : Brush/Roller: 3-5 mils. 150 sq. ft./gallon, first coat. 150 sq. ft./gallon, second coat. Clean Up: Clean application equipment with MEK (Methyl Ethyl Ketone). Note that brushes with plastic bristles will dissolve in the MEK and should be discarded after use. Technical Data: Dry Heat Resistance: 180F Abrasion Resistance: 350 mg. (ASTM D 4 0 6 0 , CS-17 wheel, 850 cycles, 1 kg., Taber Abraser) Tensile Strength: 2000-2500 psi Hardness Shore: 50 shore a scale Elongation: 100-200% Direct Impact Resistance: 20 in. lbs (ASTM D2485) Salt Fog Resistance: 1,000 hours: excellent Colors: white, orange, gray, black, mist blue, sea green, green, almond Tack Free Time: 2 hours Recoat Time: 4 hours Total Cure Time: 24 hours Application Data: Preparation of Concrete and Cement: Allow new concrete to cure thoroughly before coating. Method One: Chemical Cleaning Method Two: Steam Cleaning Method Three: Volatile Solvent Cleaning Preparation of Steel and Metallic Surfaces: Method One: Chemical Cleaning Method Two: Scraping and wire brushing Method Three: Abrasive Blasting Roller Application Brush Application Dip Application Spray Application

4


ADVANCED MATERIALS: GUARDCOTE I1 Air Dry Plastic Coating that is both Acid and Alkali Resistant and offers Superior Adhesion and Heat Resistance: Modified version of the GUARDCOTE Series 100. GUARDCOTE I1 has the same acid/alkali resistant properties as it predecessor but is specially formulated for better adhesion and can resist temperatures in excess of 212F. Coverage: Brush/Roller, 3-5 mils. 150 s q . ft./gallon, first coat. 150 sq. ft./gallon, second coat. Clean Up: Clean application equipment with MEK (Methyl Ethyl Xetone). Note that brushes with plastic bristles will dissolve in the MEK and should be discarded after use. Technical Data: Dry Heat Resistance: 212F plus Abrasion Resistance: 450 mg. (ASTM D4060, CS-17 wheel, 850 cycles, 1 kg., Taber Abraser) Hardness Shore: 70 shore A scale Tensile Strength: 2000-2500 psi Elongation: 200-300% Direct Impact Resistance: 20 in. lbs Salt Fog Resistance: 1 , 0 0 0 hours: excellent Color: Clear Tack Free Time: 2 hours Recoat Time: 4 hours Total Cure Time: 24 hours Preparation of Concrete and Cement: Allow new concrete to cure thoroughly before coating. Method One: Chemical Cleaning Method Two: Steam Cleaning Method Three: Volatile Solvent Cleaning Preparation of Steel and Metallic Surfaces: Method One: Chemical Cleaning Method Two: Scraping and Wire Brushing Method Three: Abrasive Blasting Application Data: Roller Application Brush Application Dip Application Spray Application Air-Atomized Spray Airless Spray Hot Spray

Advanced Materials 5

ADVANCED MATERIALS: PRIMECOTE: PRIMECOTE is an anti-rust compound that can be applied directly over sound, rusted ferrous surfaces. PRIMECOAT dries to a tough, hard surface which electrochemically resists rust. Eliminates sandblasting, PRIMECOAT turns rust into a protective coating. Technical Data: Roiling Point: 378F Vapor Pressure: 0.009 Solubility in Water: 100% Specific Gravity; 1 . 3 6 4 Flash Point: Non-Flammable Incompatibility: Reaction with metals will release hydrogen gas (extremely flammable) Hazardous Decomposition of Byproducts: Phosphoric oxide fumes (irritant) Evaporation Rate: Extremely low Safe

-

-

Effective

-

Efficient

Stops rust Paint lasts longer Primes metal for painting Will not chip, peel, blister or fade Seals rusted surfaces against further corrosion

Easy to Apply: Use PRIMECOAT as it comes from the container. No mixing or stirring. PRIMECOAT can be used to touch up rusted spots, avoiding adjacent non-metal or separately painted surfaces. Non-Flammable. Paint Jobs Last Longer: One application of PRIMECOAT kills all the rust stops further rust action. Paint coats adheres so tightly that moisture can't penetrate to the metal. Paint lasts and protects much longer - you save time and material costs of frequent repainting.

...

No Sandblasting: You save hours of preparation time. PRIMECOAT goes on right over the rust to form a perfect base for paint.

-

Proves its worth wherever there's rust Saves time on hundreds of maintenance jobs Etches new metal to provide good bond

6 Prepain t Specialties and Surface Tolerant Coatings

ALLIED-KELITE DIVISION: Products for Metal Surface Preparation and Finishing: Cleaners: Alkaline Spray: All Typical Metals: ISOPREP 132 (powder) ISOPREP 1 34 ( powder ) ISOPREP 138 (liquid) KOOL-SPRAY 140L (liquid) Ferrous Only ISOPREP 1 31 (powder) PROCESS 235L (liquid) Alkaline Immersion: All Typical Metals: ISOPREP 34 (powder) ISOPREP 40 (powder) ISOPREP 45 (powder) KOOL SOAK 20 (powder) CHEMIDIZE 740 (powder) ISOPREP 74# (powder) No. 780 (powder) # Will etch aluminum

Ferrous Only: SUPER SOAK (powder) ISOPREP 6 (powder) ISOPREP 7 (powder) KOOL-SOAK 10 (powder) ISOPREP PW (powder) Acid Spray: All Typical Metals: ISOPREP 163 (liquid) Acid Immersion: All Typical Metals: ISOPREP 160 (liquid) ISOPREP 1 61 (liquid) Emulsions and Solvent Emulsions: All Typical Metals: KESONIC (liquid) KESONIC C (liquid) KESONIC HF (liquid) PROTEXOL (liquid) Wetting Agent Cleaners and Detergent Additives: All Typical Metals: KEYKOTE 84 (liquid) SPRA-KLEEN (liquid)

AliiedKeiite Division

ALLIED-KELITE DIVISION: Products for Metal Surface Preparation and Finishing(C0ntinued): Electrocleaners: Alkaline: All Typical Metals: ISOPREP 57 (powder) ISOPREP EZD (powder) Ferrous Only: ISOPREP 54P (powder) ISOPREP 55 (powder) ISOPREP 56 (powder) ISOPREP 58 (powder) ISOPREP 58LT (powder) ISOPREP NCZ (powder) MULTITEMP Cleaner 65 (powder) Rust and Scale Removers for Ferrous Metals: Alkaline Immersion: ISOPREP 1 7 0 (liquid) PROCESS 235L (liquid) ISOPREP 1 7 1 (powder) ISOPREP 1 7 7 (powder) Alkaline Spray: PROCESS 235L (liquid) ISOPREP 1 71 (powder) Acid : SCALE-OFF (liquid) ISOPREP 1 51 (powder) ISOPREP 1 90 (powder)

7

8


ALLIED-~ITE DIVISION: Products for Metal Surface Preparation and Finishing (Continued): Aluminum Etchants and Additives for Caustic: Alkaline Etchants: ISOPREP 33 (powder) ISOPREP 35 (powder) Additives for Caustic: PROCESS 235CX-CF (powder) ISOPREP 62 (powder) Aluminum Deoxidizers/Desmutters: Acid: Chromated: ISOPREP 188 powder) Non-Chromated: ISOPREP 184

liquid)

Chromate Conversion Coatings: Aluminum : G o l d Finish:

IRIDITE 14 (powder) IRIDITE 14-2# (powder) IRIDITE 14-4# (liquid) Clear Finish: IRIDITE 14-9# (powder) # Accelerated Zinc Die Cast: Olive Drab Finish: IRIDITE 1 (liquid) IRIDITE 1P (powder) Bronze Finish: IRIDITE 3 (liquid) Chemical Polish: IRIDITE 4-73 (liquid) IRIDITE 4-75 (liquid) Yellow Finish: IRIDITE 5-3 (powder) IRIDITE 5P-5 (powder) IRIDITE 8P (powder) IRIDITE 8-4 (liquid) IRIDITE 80 (liquid) Black Finish: IRIDITE 6-2 (liquid)

Allied-Kelite Division

ALLIED-KELITE DIVISION: Products for Metal Surface Preparation and Finishing(C0ntinued): Brighteners: Alumimum : Aluminum Brightener No. 1 8 (liquid) ISOPREP 161 (liquid) Copper/Brass: ISOPREP 201 (liquid) Corrosion Inhibitors: Water Displacing Oil, Barrier Film: ISOPREP 220 (liquid) ISOPREP 221 (liquid) Water Emulsifiable Oil, Barrier Film: KFYKOTE OIL 65 (liquid) RUST FOE (liquid) RUST FQE I1 (liquid) Water Dilutable, Inorganic Passivating Film: ISOPREP 242 (liquid) Water Based Lacquer: IRILAC 1000 (liquid) IRILAC 1001 (liquid) IRILAC 1007 (liquid)

9

10 Prepaint Sgecialties and Surface Tolerant Coatings

ALLIED-KELITE DIVISION: Products for Metal Surface Preparation

and Finishing(C0ntinued): Phosphate Conversion Coatings: Iron Phosphates: Combination Cleaner/Phosphate: Spray : KEYKOTE 22 (powder) KEYKOTE 23LT (liquid) KEYKOTE 26# (powder) KEYKOTE 27 (powder) Immersion: KEYKOTE 2 (powder)

Phosphate Only: Spray : KEYKOTE 25 (powder) KEYKOTE 25L (liquid) KEYKOTE 28L (liquid) Immersion: KEYKOTE 25 (powder) KEYKOTE 25L (liquid) KEYKOTE 28L# (liquid)

Note: For steam phosphatizing, use KEYKOTE 4 (liquid) or KEYKOTE 22 (powder) # All phosphates above are for use on ferrous metals. Those noted are also intended for use on aluminum and galvanized steel. Zinc Phosphates: Prepaint (Microcrystalline): Spray: KEYKOTE 35 (liquid) KEYKOTE 37# (liquid) Immersion: KEYKOTE 32 (liquid) KEYKOTE 37# (liquid)

Heavy Zinc: Immersion: KEYKOTE 36 (liquid) KEYKOTE 38 (liquid) # All phosphates above are for use on ferrous metals. Those

noted are also intended for use on aluminum and galvanized steel. Manganese Phosphates: Immersion: KEYKOTE 40 (liquid) KEYKOTE 41 (liquid)


ALLIED-KELITE DIVISION: Products for Metal Surface Preparation and Finishing(C0ntinued): Phosphatizing Process Additives and Companion Products: Sealing Rinses: Chromated: KESEAL PLUS (liquid) Non-Chromated: KESEAL NC (powder) Detergent Packages: All Temperature: SPRA-KLEEN (liquid) Above 120F KEYKOTE 84 (liquid) Accelerator f o r Zinc: KEYKOTE 61 (liquid) Grain Refiner for Zinc and Manganese Phosphates: KEYKOTE 62 (powder) pH Adjuster for Iron Phosphates: KEYKOTE 81 (liquid) Blackening Agent for Zinc Phosphate: KEYKOTE 70 (liquid) Rust Preventives for Heavy Zinc Phosphate: Water Displacing: ISOPREP 220 (liquid) Water Emulsifiable: KEYKOTE OIL # 5 (liquid) RUST FOE (liquid) RUST FOE I1 (liquid)

11

12 Prepaint Specialtiesand Surface Tolerant Coatings

ALLIED-~ITE DIVISION: Products for Metal Surface Preparation and Finishing(C0ntinued): Paint Booth Products: Deflocculants: For solvent and oil based paints: KEFLOC CH (powder) For water based paints: KEFLOC W (powder) Defoamer: KEFLOC W Defoamer (liquid) Booth Coatings: Spray Booth Coating (paste) KETROL 55 (liquid) Paint Strippers: Hot Alkaline Immersion# ISPOPREP 177 (powder) STRIPPER CH (powder) PROCESS 235L (liquid) # KELTROL 7L is a paint stripper booster which enhances the performance of all of the products listed above.

Room Temperature Immersion: COLD STRIPPER 5 8 (liquid) COLD STRIPPER 6 0 (liquid) FORMULA 555 (liquid) FORMULA 1006 (liquid) Room Temperature Brush-On: A-1 27-B (liquid) STRIPPER L-46 (liquid)


ALLIED-KKLITE DIVISION: Products for Metal Surface Preparation and Finishing(C0ntinued): Specialty Surface Preparation Products for use prior to Electroless Nickel Plating Alkaline Cieaners: Caustic free, immersion for aluminum: NIKLAD ALPREP 200 Immersion for ferrous metals: NIKLAD FERROPREP 100 Non-silicated, non-etch for alumimum: NIKLAD ALPREP 204 NIKLAD ALPREP 205 Etch, immersion €or aluminum: NIKLAD ALPREP 245 Acid Cleaners: Non-etch, immersion for aluminum: NIKLAD ALPREP 230 Etch, immersion for aluminum: NIKLAD ALPREP 250 Electrocleaner: Alkaline for ferrous alloys: NIKLAD FERROPREP 170 Deoxidizer/Desmutter: Non-chromated: NIKLAD ALPREP 290 Deruster and Descaler: Alkaline: NIKLAD FERROPREP 190 Acid Pickles and Activators: For leaded steel, leaded brass, ZAMAK-3 and ZAMAK-5 zinc die cast: NIKLAD MULTIPREP 500 For cast iron, copper and copper alloys, nickel and nickel alloys, steel and stainless steel: NIKLAD MULTIPREP 501 Acid Pickle, Descaler and Desmutter: NIKLAD MULTIPREP 502

13

14


ALVIN PRODUCTS, INC.:

LAB-METAL:

Spreads like paste Hardens to metal No Mixing! No Measuring! No Heat!

LAB-METAL is a unique metal in paste form that has been tried and successfully proven in unlimited and varied industrial applications. A particular plus is LAB-METAL'S unusual formulation, which offers the user three different methods of application. Spread It On: To fill holes, depressions--rebuild worn surfaces. Paint It On: As a primer surface or to apply a tough metal coat Spray It On: To waterproof and rustproof large surface areas.

.

LAB-METAL is economical to buy, and inexpensive to use. There is no waste, and many applications can be made from a single can. Technical Data: Adhesion: Excellent adhesion to clean dry surfaces of metal, wood, plastic, glass and plastic. No heat needed to complete bond. Color: Metal grey Hardness: Between 4 and 8 on Rockwell E Scale. Using 118" ball and 100 kg. load. Coefficient of Linear Expansion: 13-17 x 10 -6 11/11F Tensile Strength: 650 pounds per square inch. Specific Gravity: 1.95 at 75F Weight: One cubic inch: 31.2 grams or 1.10 oz. Heat Resistance: When dry and hard, withstands temperatures to 350F. and is not affected by cold to minus 40F. Impervious to atmospheric conditions. Will not rust, rot--not affected by mildew--will withstand higher temperatures than 350F. if heat is applied at intermittent intervals. Chemical Resistance Acids No affect Alkalis Attacked slowly, and only after extensive immersion Gasoline No affect Petroleum No affect Petroleum solvents No affect Oil or L.P. Gas No affect Combustibility: Dry and hard material will not support combustion. Conductivity: A non-conductor. Can be plated when painted with L-M pre-plate solution. Thermal Conductivity: Est. 1-2 B.T.U.-Ft/Sq.Ft./Hr/Degrees/F.

Alvin Products, Inc.

ALVIN PRODUCTS, INC.:

15

Products:

LAB-SOLVENT: Thinner for LAB-METAL Metal Cleaner Paint Remover Paint with Metal Thin LAB-METAL with LAB-SOLVENT and brush or spray it on wood or metal surfaces. - Seal leaking tank seams - Rustproof tank interiors - Metallize wood patterns for longer life Preserves---Protects---Waterproofs---Rustproofs LAB-SOLVENT is a specially formulated blend of solvents specifically recommended as the agent for thinning LAB-METAL to paint consistency for brushing and spraying. LAB-SOLVENT cuts grease, oil and dirt, and is particularly recommended as a metal cleaner and degreaser to prepare surfaces for LAB-METAL applications. LAB-SOLVENT removes paint quickly and efficiently. LAB-SOLVENT is packaged in pint and gallon cans. GALVAX: The zinc-rich spray that stops rust cold! GALVAX rustproofs any metal exposed to corrosion and rust. GALVAX zinc-rich coating electro-chemically bonds with all metals to stop rust creepage and corrosion. GALVAX is not a paint, but a 9 5 % pure-zinc compound that sprays on cold to protect the surface from rust. GALVAX heals itself even when scratched! GALVAX is equal to hot-dip galvanizing, and is an instant cure for damaged hot dip coatings and welding touch-ups. GALVAX Cold Galvanizer: Production: Cold galvanize parts and production pieces in your shop. Use it for all metal fabrication. Maintenance: Fan blades, metal doors, roofs, window frames, auto, trailer and truck bodies, storage tanks, air conditioners, piping, all welds. Construction: Highway guard rails, culverts, docks, fences, ducts, underground pipes, bridges, structural steel. Other: Ships, sports equipment, dairy equipment, ornamental iron, farm machinery, mining equipment, oil rigs. Technically speaking the reaction of GALVAX with metal is unique. GALVAX is a zinc-rich compound that electro-chemically reacts on contact with iron, steel or aluminum and actually fuses with the base metal to provide rust and corrosion resistance. GALVAX is not a paint, but can be painted if desired. GALVAX will bond with hot-dip finish and is excellent for recoating weathered galvanized surfaces and for repairing areas damaged by welding.

16 Prepaint Specialties and Surface Tolerant Coatings

AMERON: AMERGUARD 1 4 8 Waterborne Acrylic Primer: Product Data: LOW odor - Dries fast, minimum downtime - Good mechanical, physical properties - Accepts a wide range of topcoats - Maximum corrosion protection on steel - Minimal surface preparation Single-package convenience Brush, roll or spray VOC-compliant - High build Surface tolerant - Compatible with most existing coatings Good dry fall characteristics - Quick, easy clean up

-

-

AMERGUARD 1 4 8 is a high-performance, high-build, waterborne acrylic primer with excellent inhibitive features. Ideal for steel and other substrates, it provides a bond between existing painted or primed surfaces and suitable AMERON high-performance topcoats. AMERGUARD 1 4 8 may be applied by brush, roller, and airless or conventional sprayer. Minimal surface preparation is required. It can be topcoated after 3 hours at 70F. When used with a suitable topcoat, AMERGUARD 1 4 8 has excellent resistance to weathering, water, and splash and spill of a variety of industrial and household chemicals. It also inhibits corrosion and resists cracking and impact damage. Typical Uses: - Structural steel - Tanks - Pipe and equipment - Rebar coating Marine vessels topsides and interiors Offshore platform interiors

-

Physical Data: Finish: Flat Color: Off-white, oxide red Components: 1 Curing mechanism: Drying Volume solids Calculated: 41+3% Dry film thickness per coat: 3 to 5 mils ( 7 5 to 1 2 5 microns) Coats: 1 Theoretical coverage: ft2/gal m2/~ 1 mil ( 2 5 microns) 657 16.1 3 mils ( 7 5 microns) 21 9 5.4 voc : 1 . 9 3 lb/gal 232 g/L Flash point (SETA) F C AMERGUARD 1 4 8 >200 >93

Ameron

AMERON CORP.:

17

AMERGUARD 149 Waterborne Epoxy Primer:

Product Data: - Extra-heavy-duty, rust-inhibitive primer for steel substrates - Solvent-free, ideal for restricted and sensitive environments - VOC-compliant - Adheres to a variety of different coatings - Can be topcoated with waterborne and solvent-based epoxy coatings - Brush, roll or spray - Quick, easy clean up AMERGUARD 149 primer provides excellent corrosion protection for steel in chemical plants, oil refineries, nuclear and fossil fuel power plants, food processing plants, pharmaceutical plants, marine topsides and interiors, offshore platforms and other environments that require solvent-free, extra-heavy-duty protection. Apply AMERGUARD 149 over prepared steel, aluminum and galvanizing. AMERGUARD 149 is an excellent primer for high-performance AMERON topcoats such as AMERGUARD 220 waterborne acrylic, AMERGUARD 335 waterborne epoxy acrylic and a variety of AMERON epoxy coatings. Physical Data: Finish: Semigloss Color: White, off-white Components: 2 Curing Mechanism: Drying and chemical reaction between components Volume solids calculated: 48%23% Dry film thickness per coat: 2 mils (50 microns) Coats: 1 or 2 Theoretical coverage: ft21gal m2IL 1 mil (25 microns) 770 18.9 2 mils (50 microns) 385 9.4 voc 0.0 lblgal 0.0 gIL Flash point (SETA) F C cure and resin ,200 >93 mixed >200 >93 AMERGUARD 928 185 85 Application Data: Applied over: Prepared steel, aluminum, galvanizing Surface preparation: Abrasive blast Method: Spray airless or conventional, brush Mixing ratio (by volume): 3.15 gal cure to 1.85 gal resin per 5-gal unit F/C Pot life: 90132 70121 5011 0 f 11 23 (hours)


AMERON CORP.:

AMERGUARD 335 Waterborne Epoxy Acrylic:

Product Data: Self-priming Direct to substrate VOC-compliant Dries fast, minimum downtime Interior or exterior use Suitable for OEM Brush, roll or spray Low odor High gloss Durable Cleanable Water-reducible Outstanding color and gloss retention Excellent freeze/thaw stability Wide color range AMERGUARD 335 is a high-performance waterborne epoxy acrylic coating for steel, concrete, masonry, wood, galvanizing, aluminum substrates, previously painted surfaces and drywall. Typical Uses: - Floors, walls - Food processing plants - Institutional maintenance and new construction Schools Kitchens Storage areas Hospitals Laboratories - Industrial maintenance and new construction Tank exteriors Piping Eauitment Structural steel - Marine applications Vessel topsides and interiors Offshore platform topsides and interiors Not recommended for continuous immersion Physical Data: Finish: Gloss Color: Standard and custom Components: 2 Curing machanism: Drying; chemical curing (crosslinking) V o l i i m e solids: AMERGUARD 335: 43%?3% 335 clear: 36%?3% Mix ratio (volume): 8 resin:l cure Dry film thickness per coat: 2-3 mils Coats: 1-2 Theoretical coverage: ft2/gal m2 /L 1 mil: AMERGUARD 335 689 17 335 clear 577 14 3 mils: AMERGUARD 335 229 5.6 335 clear 192 4.7 VOC (mixed) 2.4 lb/gal 288 g/L

heron

19

AMERON: AMERLOCK 400 High-solids Epoxy Coating:

Product Data: - VOC-compliant - High performance general maintenance coating for new or old steel Cures through wide temperature range - Self-priming topcoat over most existing coatings - Can be overcoated with wide range of topcoats - Compatible with prepared damp surfaces - Compatible with adherent rust remaining on prepared surfaces 5 mils or more in a single coat Resists high humidity and moisture

-

-

Typical Uses: AMERLOCK 400 is used in those areas where blasting is impractical or impossible. As a maintenance coating, AMERLOCK 400 protects steel structures in industrial facilities, bridges, tank exteriors, marine weathering, offshore, oil tanks, piping, roofs, water towers and other exposures. AMERLOCK 400 has good chemical resistance to splash/spillage, fumes and immersion in neutral, fresh and salt water. Outstanding Characteristics: Amerlock's low solvent level meets VOC requirements, reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface, often a major cause of coating failure with conventional epoxies and lower solids systems. Physical Data: Finish: Semigloss Color: Standard, Rapid Response, custom colors and aluminum Components: 2 Curing mechanism: Solvent release and chemical reaction between components Volume solids: 400: 83%*3% 400AL: 88%*3% Dry film thickness (per coat): 5 to 8 mils (125 to 200 microns) Coats: 1 or 2 Theoretical coveraqe: 1 mil (25 microns) ft21gal m2/~ 400 1331 32 400AL 141 1 34.6 5 mils (1 25 microns) 400 266 6.5 400AL 282 6.9 voc lb/gal 9lL 163 400 mixed 1.4 204 1.7 mixedlthinned (3 pt) 120 400AL mixed 1 .o 239 mixedlthinned ( 1 4 pt) 2.0 146 400FD mixed 1.2 189 1.6 mixedlthinned ( 4 pt)


AMERON CORP.: AMERSHIELD Aliphatic Polyurethane:

-

Unique, high-solids, high-build, multifunctional coating High-gloss, self-priming coating Excellent gloss retention Direct to metal or concrete Outstanding abrasion, reverse and direct impact resistance Meets environmental VOC requirements Good chemical and stain resistance Tough and flexible coating Outstanding Characteristics: AMERSHIELD displays high gloss, shows excellent color and gloss retention during extended service periods. The direct-tometal capabilities of AMERSHIELD provide a single-coat system at reduced installation cost. Physical Data: Finish: Gloss Color: RAPID RESPONSE colors, Clear coat, LT# Components: 2 Curing mechanism: Solvent release and chemical reaction Volume solids: Standard: 7 3 * 3 % Clear coat: 6 3 * 3 % Aluminum (calc.): 6 2 2 3 % DFT per coat: 5 mils ( 1 2 5 microns) Theoretical coverage: 1 mil ( 2 5 microns) ft2/gal m2/L 1170 28.7 Standard 1010 24.8 Clear coat 994 24.4 Aluminum 5 mils ( 1 25 microns) Standard 234 5.7 Clear coat 202 4.9 Aluminum 199 4.8

voc

Mixed lb/gal 9/L 2.2 263.8 Standard Clear coat 2.4 293.8 2.6 311.9 Aluminum Mixed/thinned Standard 2.7 325.1 Clear coat 2.9 351.8 Aluminum 3.1 367.8 F C Temperature resistance (dry) continuous 200 93 intermittent 250 121 Flash point (SETA) F C cure 122 50 resin 110 43 mixed 115 46 AMERCOAT 9 2 3 102 39 AMERCOAT 1 2 0 -1 8 # Low toxicity (LT) colors do not contain lead or chromium pigments and may require 2 coats depending upon substrate color. Clear does not contain pigments.

Bartlett Chemicals, Inc.

BARTLETT CHEMICALS, INC.:

21

DOLPHIN BARTKOTE:

DOLPHIN BARTKOTE is a specially prepared product that combines rust removal and rust preventive qualities in the same compound. BARTKOTE's powerful ingredients will neutralize rust, especially where removal of it is difficult. After an application of BARTKOTE, rust is converted into a porous surface which readily accepts paint, brushed or sprayed. Metal will not rust under the paint, and paint life will be lengthened significantly. Typical Applications: DOLPHIN BARTKOTE has proven it effectiveness for many years. It has been used successfully in the Gulf of Mexico oil industry where moist air combined with salt spray causes heavy corrosive damage to steel. Availability: 5 5 Gallon Returnable Plastic Drum 5 Gallon Plastic Container 1 Gallon Plastic Bottles ( 4 per case) Properties: Appearance: Clear Liquid PH: 1-2 Specific Gravity: 1 . 2 5 0 Lb/gal: 1 0 . 5 Degrees Be: 3 0 Color: Green Acid Equivalent: 3 5 % Use Directions: 1 . Wire brush to remove loose rust and scale. Remove grease and dirt by cleaning with mineral spirits or soap and water. 2 . Brush or spray BARTKOTE full strength, completely covering the surface, and let it dry. Parts can be dipped in BARTKOTE. Rinsing is not necessary. 3 . When material is dry it acts as an excellent primer for the metal which can then be painted over with any good oil paint.

22

Prepaint Specialties and &dace Tolerant Coatings

BECK CHEMICALS, INC.:

Product Line:

BECKS Concrete Sealant: MAGNA SEAL is an organic film-forming penetrant which deeply permeates concrete, brick and other construction substrates; even rusted surfaces through to the metal. Its film-forming properties seal out corrosion including corrosive acid rain. The film forming resins of MAGNA SEAL are a combination of acrylics and hard resins properly plasticized to produce maximum resilience. MAGNA SEAL Sealant chemically links the film to the substrate, thus producing unusual adhesion. MAGNA SEAL incorporates a time proven blend of ultra-violet absorbers which blank out the debilitating affects of the sun. Although MAGNA SEAL contains 37% solids, it is almost invisible on the construction substrates. Controlled penetration insures a wet film deposit thick enough to react thoroughly with the building material. The tough skin left by the dried sealer is unsurpassed in resistance to salt and moisture. It will accept and bond with most top coats. MAGNA SEAL is available in colors for second coat. BECK'S RUST PREVENTATIVE OIL: BECK'S RUST PREVENTATIVE OIL is a petroleum oil base, nonfilm former with deep penetrating qualities. Its viscosity is adjusted to leave a film of sufficient thickness to resist all types of weather and give full outdoor protection against corrosion for about two months; indoor protection for 6 months. Purpose: To protect steel from rusting for a maximum time duration without forming a film which cannot be removed in ordinary industrial degreasing equipment. BECK'S RUST PREVENTATIVE OIL is recommended for protection of in-process metal; painted or partially painted machinery in transit or in storage; tools, dies, fixtures, etc.; cement contractor's equipment. BOOTHWAX H: A non-sticky, non-greasy protective coating for temporary protection of floors, equipment and areas where paint overspray and spillage must be cleaned. Physical Properties: BOOTHWAX H is a creamy white semi-paste which can be brushed on or sprayed with ordinary paint pressure spraying equipment. When dry, BOOTHWAX H leaves a smooth non-greasy surface from which paint can easily be peeled or scraped. BOOTHWAX H is non-toxic, non-injurious to skin or clothing and non-corrosive to metal or plastic. Freeze point about -10F.

Beck Chemicals, lnc.


23

Product Line(C0ntinued):

DRY BRUSH CLEANER: BECK'S DRY BRUSH CLEANER restores paint brushes which have not been cleaned after painting. BECK'S DRY BRUSH CLEANER swells the resins in the old paint, thus breaking the bond between the bristles and the paint. The process usually requires an overnight soak. ECONOSTRIP B-251-W: ECONOSTRIP B-251-W is a viscous paint remover formulated to remove Epoxys and other polymerized film from wood. It contains no "extenders or fillers". Accelerated for maximum performance. Properties & Description: ECONOSTRIP B-251-W is non-inflammable; will not raise the grain or discolor wood, it is adhesive, possessing the proper viscosity to insure good clinging properties; it is homogeneous and needs no agitation prior to use. It does not dissolve paint but simply breaks the bond between the paint and wood. EPOXYSTRIP: An accelerated industrial paint stripper to break the bond of adhesion and to penetrate the chemical resistance formulated by modern paint manufacturers in today's toughest finishes-meets the challenge with a new product called EPOXYSTRIP. EPOXYSTRIP is the result of countless tests and research on the many films created by paint manufacturers. Purpose: For removal of epoxies and other polymerized films from metal. For dip tank use, order EPOXYSTRIP "T". For brushing or spraying on spray booth walls, large equipment, etc., order EPOXYSTRIP "B". Recommended for industrial use only. Properties & Description: EPOXYSTRIP "T" is: non-flammable; thin as water; light brown in color, non-corrosive up to 4 hours immersion; formulated to strip even the toughest films from aluminum, brass, copper and steel. "SLOW EVAPORATOR"--contains its own blended evaporation retardant. EPOXYSTRIP "B" is: same physical properties as above except thickened for brush or spray. EPOXYSTRIP T-160: EPOXYSTRIP T-160 is a clear thin liquid compound especially formulated to serve as a universal paint remover for sale to industrial consumers. This compound may be readily used for removal of enamels and lacquers from both wood and metal surfaces. EPOXYSTRIP T-I60 is: Non-inflammable Non-corrosive Will not raise the grain or discolor the wood Homogeneous Stable

24

Prepaint s;oeCialties and Surface Tolerant Coatings


Product Line(Continued):

FERRO-BET #11 De-Rusting & Rust Passivating Agent: FERRO-BET is a compound used as a metal treatment prior to painting. FERRO-BET provides excellent adhesion of paint to galvanized iron, zinc, aluminum, tin and steel. It successfully passivates corrosion on metal and transforms iron rust (oxide) into iron/zinc/phosphate. Where steel is heaviy rusted or coated with mill scale, FERRO-BET # l o DE-SCALER should be applied prior to using FERRO-BET # 1 1 . Properties & Description: FERRO-BET: - Is a mildly acid clear liquid Is packaged in plastic containers Provides an iron/zinc/phosphate coating which cannot easily be removed Provides excellent adhesion with paint - Saves paint and prevents rust migration underneath paint

-

FLEXTEMP : A liquid, quick-drying masking compound which is offered in two colors as well as in its clear form. Color designation is as follows: FLEXTEMP #20, Clear; FLEXTEMP # 2 5 , Blue; FLEXTEMP # 3 0 , Red. FLEXTEMP is well stabilized against brittleness due to light, heat, age or exposure to acids. Because of its unusual resistance to plating acids, FLEXTEMP is preferred for use in the semiconductor field where hydrofluoric acid traditionally causes a problem. Uses : "STOP-OFF" Lacquer for use in the electroplating industry; patching molded rubber plating tank liners; protective coating for plating tanks. Special Advantages: 1 . Unusual resistance to attack by plating acids 2. Quick drying tough elastic film peels off easily 3 . Protects against rust and corrosion 4 . Needs no stirring--pigments remain suspended indefinitely FOYAL GRAFFITI REMOVER: A non-sticky, non-greasy preventative coating to protect all substrates from permanent adhesion of graffiti. FOYAL GRAFFITI PREVENTER penetrates deeply into most substrates and forms a coating which withstands weather extremely well. Even the hottest exposure to sun will not interfere with the protective qualities of FOYAL GRAFFITI PREVENTER. This unusual product interfers with the adhesive and penetrating properties of paints, stains and inks. FOYAL GRAFFITI PREVENTER is non-toxic, non-injurious to skin or clothing, non-corrosive to metal or plastic. The dry film has a high melting point above 250F.

Beck Chemicals, Inc.

BECK CREMICALS, INC.:

25

Product Line(C0ntinued):

GRAFFITI EATER # l : Paint remover to remove paint from large surfaces Recommended for ships, storage tanks, large transformers, motor vehicles, buildings, etc. GRAFFITI EATER #2: GRAFFITI EATER # 2 is a thickened compound especially formulated to meet the challange of graffiti and other unwanted paint deposits from construction materials such as concrete, stucco, marble, stone, metal and wood. GRAFFITI EATER # 2 is highly synergised with organic acids and deep penetrants to meet the stringent challenge presented by all types of graffiti. Properties & Description: GRAFFITI EATER #2 is non-flammable, non-corrosive to metals, except zinc and magnesium; water rinseable, and possesses the proper viscosity to insure good clinging properties to dry substrates. There is no loss due to excessive run-off. GRAFFITI EATER #2 is homogeneous--therefore, ready to use anytime; stable; formulated to surpass the performance of all conventional paint remover compounds. GRAFFITI EATER #3: GRAFFITI EATER # 3 is a thickened compound especially formulated to meet the challenge of graffiti and other unwanted paint deposits from construction materials such as concrete, stucco, marble, stone, metal, and other hard surfaces. GRAFFITI EATER #3 is highly synergised with organic acids and deep penetrants to meet the stringent challenge presented by all types of graffiti. Properties & Description: GRAFFITI EATER # 3 is non-flammable, non-corrosive to most metals except zinc & magnesium; water rinseable, and possesses the proper viscosity to insure good clinging properties to dry substrates. There is no loss due to excessive run-off. GRAFFITI EATER # 3 is homogeneous--therefore, ready to use anytime; stable; formulated to surpass the performance of all conventional paint remover compounds. GRAFFITI EATER 6 6 : Purpose: 1 . Stripping graffiti from Plexiglas or Lexan sheet. 2 . Stripping fresh graffiti from painted substrates. General Description: GRAFFITI EATER #6 is a light amber gel containing blended solvents, wetting agents and evaporation retarders. Special Advantages: GRAFFITI EATER #6 has been formulated to remove all types of painted graffiti in the shortest exposure time without affecting the substrate. This product has little or no effect on Plexiglas, Lexan, wood or metal.

26 Prepainr Specialties and Surface Tolerant Coatings



GRAFFITI RESISTOR #7: Unique paintable coating for protection against all types of graffiti contamination--including grease. GRAFFITI RESISTOR #7 also resists flame! When the wall is subjected to flame, GRAFFITI RESISTOR #7 puffs up and forms an insulating air pocket between itself and the substrate. GRAFFITI RESISTOR #7 cannot be set afire! It simply will not burn. GRAFFITI RESISTOR #7 is intended for indoor use only. A wide range of colors is available. Although GRAFFITI RESISTOR #7 resists all paints, yet it can be removed with a high pressure washer or steam cleaning unit. GRAFFITI RESISTOR may be recoated only with more GRAFFITI RESISTOR. Properties & Descriptions: 1 . Leaves hard, scratch resistant finish 2. Pleasant semi-gloss sheen 3 . Applied by brush or spraygun 4 . Air Dries 5. Non-Toxic--Non-Flammable KOROBEX: KOROBEX is a fast-drying plastic primer composed of various resins. It is non-poisonous, self-phosphatizing and especially adhesive to steel, aluminum and other metals, oiled woods, hardened fiber surfaces, glass, plastics, etc. KOROBEX penetrates deep into minute pores; it phosphatizes and arrests the migration of rust. KOROBEX has good flow-out and filling properties. KOROBEX adheres best to clean and non-rusty surfaces, but it also has very good adhesion to lightly rusted, and above all, oily surfaces. Not even silicone will prevent KOROBEX adhesion. KOROBEX is resistant to oil and gasoline and, after baking, it is also resistant to many solvents. KOROBEX withstands temperatures up to 200C. KOROBEX is used where a fast-drying primer with exceptional adhesion is required. KOROBEX is particularly well suited as a prime-coat for refinishing engines, machinery and equipment which is difficult to clean satisfactorily and/or to completely remove greasy contamination. A priming treatment with KOROBEX on, for example, iron ingots or steel bars will prevent rust formation during storage and fabrication. KOROBEX also stops oil from penetrating the pores of the metal during production. Composition: Phenolic plastic For spraying, thin with 1 0 0 % KOROBEX Special Thinner or a cellulose thinner. For dipping, use 20-30% of the above. For brushing, mix 2 parts KOROBEX with 1 part thinner.

Beck Chemicals, lnc.


27

Product Line(Cont1nued):

KLEEN BOND "B" : A new phosphoric acid-type compound containing solvents, wetting agents and inhibitors for the "brush-on/wipe-off" metal cleaner and metal conditioner trade. KLEEN BOND "B" is a new product with improved wetting and dispersion qualities, designed to clean and prepare steel for painting by a simple inexpensive hand method. KLEEN BOND "B" is a liquid which can be diluted with 2 or 3 parts of water for use. It has a mild, pleasant odor, is completely water soluble, is non-toxic and non-flammable. KLEEN PEEL Plastic Film: A white plastic masking liquid which dries very quickly, leaving a white glossy protective coating over painted or unpainted metal. KLEEN PEEL represents the ultimate in vinyl coatings, incorporating every advantage which chemistry can build into this type of product. KLEEN PEEL is well stabilized against brittleness due to light, heat or age. It will hold the maximum paint load without pulling away from the metal. KLEEN PEEL offers extraordinary tensile stength and has spray and flow-out characteristics similar to paint. Uses : Spray booths--in plant aluminum processing--product protection against corrosion and scuffing during transportation or storage. Special Advantages: 1 . No Fire Hazard--shows no fire point--no true flash point 2. Sprays without creating cob-webs--flows together like paint--thus permitting thinner coats for greater economy 3 . Dries to a high gloss--for maximum light reflectivity 4 . Elastic tough film peels off in large sheets 5. Protects against rust and corrosion 6. Needs no stirring--white pigments remain suspended 7. Not necessary to store in special room with flammable paint


BECK CHEMICALS INC.:

Product Line(Continued1:

KLEEN PEEL "WS" : A water base strippable coating used for masking against paint overspray on metal, wood, painted or unpainted surfaces. KLEEN PEEL "WS" represents the ultimate in nonsolvent strippable coatings. It is well stabilized against brittleness and it will not be softened or penetrated by solvent-based paints. Uses : KLEEN PEEL "WS" does not shrink after scoring. It is therefore, particularly useful in the sign painting industry. It is also excellent for the protection of spray booth walls. Spray booths--in plant aluminum processing--product protection against corrosion and scuffing during transportation or storage. Special Advantages: 1 . Does not create the fire hazards of wet PVC coatings. 2. Elastic-tough film easily peels off. 3 . Needs no stirring. 4 . Not necessary to store in special room for temperature LEXISTRIP: Purpose: 1. Stripping graffiti from Plexiglas or Lexan Sheet. 2. Stripping fresh graffiti from painted substrates. General Description: LEXISTRIP is a light amber gel containing blended solvents, wetting agents and evaporation retarders. Special Advantages: LEXISTRIP has been formulated to remove all types of painted graffiti in the shortest exposure time without affecting the substrate. This product has little or no effect on Plexiglass, Lexan, wood or metal. PAINTOFF-1 60: PAINTOFF-160 is a honey colored thickened compound especially formulated to serve as a universal paint remover for sale through retail store outlets. This compound may be readily used for removal of enamels and lacquers from both wood and metal surfaces. Properties & Description: PAINTOFF-160 is: Non-inflammable Non-corrosive to metals Will not raise the grain or discolor wood Adhesive--Possessing the proper viscosity to insure good clinging properties; hence, there is no loss due to excessive run-off Homogeneous--Stable

Beck Chemicals, inc.


29


RUST CONTROL OIL: Phosphatizes as it Penetrates RUST CONTROL OIL is an organic film-forming penetrant which permeates rusted surfaces through to the metal underneath the rust. Its film-forming properties seal out all air, moisture and other corrosion inducing elements. RUST CONTROL OIL is an excellent phosphatizer in its own right. After it is applied to metal (rusted or unrusted), its organic phosphatizing properties change rust (ferric oxide) to iron phosphate and etch the steel surface, thus chemically linking the film to the metal. The result is a primer coat of unusual adhesion. Controlled penetration of RUST CONTROL OIL into rusted surfaces insures a wet film deposit that is thick enough to react thoroughly with rusted surfaces. The tough skin left by the dried sealer is unsurpassed in resistance to salt and moisture. It will accept and bond with all top coats except the fast-drying lacquers. RUST CONTROL OIL is recommended for corrosion protection of steel construction, ships, tanks, machinery, tools, casting, dies, etc.; also as a protective coating for aluminum, zinc, galvanize and die castings. SINTERKOTE: High-temperature anti-corrosion coating Longer product service life with new economies for designer and manufacturer SINTERKOTE is a high-temperature resistant single-compound enamel for protecting interior and exterior metal surfaces against oxidation and corrosion. Thorough its durability, corrosion resistance and ease of application, SINTERKOTE is providing designers and manufacturers with a simple and economic means of extending the service life and guarantees of their products without resorting to costlier corrosion-resistant alloys. Primary targets of SINTERKOTE are products made of ordinary milled steels which reach varying temperatures up to 850C and which must be protected against scaling and/or rusting. Protected by SINTERKOTE, these products have service-life potentials of stainless. SINTERKOTE Properties: SINTERKOTE's exceptional stability under high temperature and corrosion resistance derive from simultaneous physical and chemical actions that take place during drying. SINTERKOTE Uses: Currently, SINTERKOTE is proving highly successful and gaining wide acceptance in two broad use areas: Mufflers/Exhaust Systems Hot Tubes/Surfaces




SPRAY GUN CLEANER: Beck's SPRAY GUN CLEANER is an amber-colored liquid especially formulated to remove non-pulmerized paints, lacquered and latex emulsions from spray guns and other spray painting equipment which can be immersed into the cleaner. It will not attack washers and packing material. Properties & Description: BECK'S SPRAY GUN CLEANER is: Non-inflammable Non-corrosive Not destructive to spray gun packings Thin liquid Low toxicity VAPO-BAR: Easy-to-apply, low-cost butyl coating resists weather, water, chemicals--ideal for construction, automotive, process industries. VAPO-BAR is an inert, non-polar, two-part chemically curing butyl rubber compound that can be applied quickly and economically by brush, roller or airless spray to produce uniform, long-life film barriers of superior resistance to water, water vapor, ultra-violet radiation, weather, ozone, sunlight, causttics, acids, oxygenated solvents and salt-solutions. VAPO-BAR is fully effective in temperatures ranging from -60F to 250F. Its exceptional properties and ease of application make VAPO-BAR ideal for all types of construction, for chemical and low-temperature process equipment, and for the automotive industry. General Contruction: VAPO-BAR compounds meet the most important cost and effectiveness criteria of the construction industry: - High resistance to transmission of water vapor - High resistance to weather and ozone - High resistance to fertilizers, farm chemicals, mold and bacteria Excellent adhesion to foam, concrete and wood, without primers High durability Permanent flexibility and elacticity to accomodate temperature changes

-

Berlage

31

BERLAGE: Rust Proofing ANOGAL: Designed to be the most reliable primer available, suitable for easy application to any size of steel structure or fabrication, new or existing. Rustproofing ANOGAL is a highly effective rustproofing coating based on very finely divided, highly anodic, metallic powders held in a specially developed organic resin plastic medium which is itself resistant to corrosion. It is a "one pack" material, ready mixed to a brushing consistency and it may be applied by brushing, rollering and by airless and conventional spray equipment. How ANOGAL stops rust: ANOGAL provides electro-chemical (cathodic protection) action against rust. A coating of ANOGAL applied to any iron or steel surface acts as the anode of a cell in which the iron is the cathode of the circuit, connected by the usually damp environment which acts as the electrolyte. In this arrangement, the ANOGAL slowly passes into solution, providing charged ions to the iron cathode, thus passivating the normal tendency of iron to combine with charged oxygen and form rust (iron oxide). If a coating of ANOGAL is pierced or broken, galvanic action takes place at the broken edge, preventing rust from creeping underneath the rest of the coating. Protection given by ANOGAL may be compared with that given by other metal coating methods, e.g. flame spraying, hot dip galvanising or electro-plating. However, ANOGAL is far cheaper than any of these methods. Features: - Provides a length of life equivalent to hot dip galvanising at less cost. - Can be overpainted with any type of finishing paint without softening. - Is non-toxic and non-contaminating. - Protects in the temperature range -20F to 650F (-28C to 342C). - Is ready mixed for immediate use yet has all the physical properties of a chemically cured coating. Is electrically conductive and may be used as a welding or shop primer. Can be applied to a damp surface. - Outlasts ordinary oil based priming systems by at least three times under similar conditions. - Is proved by 1 2 years' full scale use. Inspections can be arranged.

-

Technical Data: Specific Gravity: 2.24 Color and Finish: Light battleship grey when dry. Viscosity: 25 seconds on the first 50 mls. at 60F (16C) through a No. 4 Ford efflux cup Covering Capacity: 417 square feet per gallon approximately


BIG THREE INDUSTRIES, INC.: Aluminized BIOXIDE Rust Preventive Coating Weldable Primer: The rust-preventive that's got it all going for you.

-

-

-

Unlike ordinary preventives, BIOXIDE has no objectionable compounds to contaminate weld area. Leaves no residue or slag. Safe for high temperatures, high atmospheric pressures. Provides protective coating, before welding. Can be brushed, dipped or sprayed. Covers approximately 1,000 square feet per gallon. 800 Withstands 800F working temperature making it suitable for high temperature work in refineries and chemical plants. Effective on all steels, including high tensile carbon moly and chrome moly. Free from lead, sulfur, zinc, cadmium, mercury, chlorine or other halogens. Safe for nuclear fabrication industry. Compatible with normal welding methods. Resists salt spray. A superior primer for paint and other coatings. An anti-spatter agent and provides low friction surface for movement of sliding copper dam on automatic vertical up welding.

-

The weldable rust-preventive for x-ray quality welds. If you're still re-dressing weld surfaces, you're racking up lots of unnecessary manhours on each job. This makes you less competitive. Means less profit when you bill the job out. Say hello to BIOXIDE, the steel pipe cinch. You simply weld right over this remarkable rust-preventing coating, so there is no preparation time. Even after BIOXIDE has been out in all kinds of weather for six months or more you can skip the time consuming clean-up steps. You just go ahead and weld. And BIOXIDE gives a far better weld, too. Since it forms aluminum oxide in the weld, it reduces porosity and pinholing and improves weld quality.

M.A. Bruder & Sons, lnc.

M. A. BRUDER

&

SONS CO., INC.:

Exterior Coating Systems:

FRESH KOTE Alkyd Exterior Primer: High hiding primer designed to seal wood trim and siding. Dries to a smooth finish which provides an excellent foundation for both latex and alkyd topcoats. Vehicle: Oil-Alkyd % Solids by Volume: 60 Rec. Spread Rate sq. ft. per gal.: 400 @ 2.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 6-8 Recoat: 18-24 FRESH KOTE Exterior Latex Primer: Recommended undercoat for FRESH KOTE Latex House Paint on non-staining wood surfaces. Vehicle: Acrylic Latex % Solids by Volume: 37 Rec. Spread Rate sq. ft. per gal.: 350 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: # - 1 Recoat: 2-4 LOK-TITE Latex Surface Conditioner: An alkali resistant sealer designed to penetrate and seal porous masonry and to revitalize firm chalky surfaces before applying latex emulsion paints. Vehicle: Acrylic Latex % Solids by Volume: 21 Rec. Spread Rate sq. ft. per gal.: 275 @ 1.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4 - 1 Recoat: 3 - 4 SEA SHORE Alkyd Primers: Premium quality oil based primer for exterior wood. Can be topcoated with alkyd or latex finish coats. Excellent wetting and penetrating properties. Can be applied to slightly chalky surfaces. Vehicle: Oil-Alkyd % Solids by Volume: 61 Rec. Spread Rate sq. ft. per gal.: 475 @ 2.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4-6 Recoat: 18-24 RUST 0 LASTIC HYDRO-PRIME: Water reducible primer/finish for use on properly prepared ferrous galvanized or previously painted metal. Has excellent rust inhibition and resistance to flash rusting. May be overcoated with solvent or latex finish coats. Vehicle: Acrylic Latex % Solids by Volume: 41 Rec. Spread Rate sq. ft. per gal.: 375 @ 1.5 mils Drying Time: Hours @ 70F., 50% R.H.: Touch: 1/4 - 1/2 Recoat: 2 - 4

33


M.A.

BRUDER & SONS, INC.:

Exterior Coating Systems(Continued):

PLY-TILE 520-R-17 Primer: Corrosion and chemical resistant lead primer that bonds tightly to metal surfaces. Suitable for waste and water treatment plants, tank linings and where extreme toughness and abrasion resistance are required. Blast cleaning for best results. Mix Ratio, 1:l; Pot Life @ 70F: 8 hours. Vehicle: Epoxy-Polyamide % Solids by Volume: 50 Rec. Spread Rate sq. ft. per gal: 360 @ 2.0 mils Drying Time: Hours @ 70F. 50% R.H.: Touch: 2-4 Recoat: 18-24 PLY-TILE 520-W-360 Primer: Lead free primer designed for potable water tank interiors. Provides excellent adhesion to ferrous and non ferrous metal as well as concrete surfaces. Meets A.W.W.A. Interior System #1 when topcoated with PLY-TILE 520 Coatings. EPA authorized for use in potable water tanks. Mix Ratio, 1:l; Pot Life @ 70F: 8 hours. Vehicle: Epoxy-Polyamide % Solids by Volume: 49 Rec. Spread Rate sq. ft. per gal.: 300 @ 2.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4-6 Recoat: 18-24 Interior Coating Systems: RUST 0 LASTIC HYDRO-KOTE: Water reducible primerlfinish for use on properly prepared ferrous, galvanized or previously painted metal. Has excellent rust inhibition and resistance to flash rusting. May be overcoated with solvent or latex finish coats. Vehicle: Acrylic Latex % Solids by Volume: 41 Rec. Spread Rate sq. ft. per gal.: 375 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 114 - 112 Recoat: 2 - 4 LOC-TITE Stain Sealer: Recommended for sealing bleeding-type stains such as smoke, grease and water soluble dyes. Particularly useful for sealing woods that contain tannin, such as cedar, redwood and mahogany. Controls grain-raising of unpainted fir plywood and other soft woods. For interior use. Vehicle: Vinyl Toluene % Solids by Volume: 41 Rec. Spread Rate sq. ft. per gal.: 400 @ 1.5 mils - 1 Drying Time: Hours @ 70F, 50% R.H.: Touch: Recoat: 1 - 2

M A . Bruder & Sons, Inc. 35

M.A.


FRESH KOTE Enamel Undercoater(A1kyd):

An easy brushing enamel undercoater designed to seal and provide a suitable surface for finishing with gloss or semigloss enamels. Provides a smooth surface with excellent film build and hiding. Recommended Uses: For interior wood or clean ferrous metal(See Important Information) Top Coat Recommended: Interior FRESH KOTE gloss or semi-gloss finishes. Technical Data: Theoretical Coverage: 835 sq. ft. per gal. per dry mil Recommended Dry Film Thickness: 1.5 mils per coat Drying Time @ 70F, 50% R.H.: To touch: 2-4 hours To recoat: 18-24 hours Thinner: Brush & Roll: Paint Thinner, up to 5% Spray: Naphtha, up to 1 0 % Gloss: Low Sheen Wt/Gallon: 1 2.6 lbs. Viscosity: 108 K.U. Solids Content: Wt. 75% Vol. 52% Temperature Linit (Dry): 225-275F Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 6 6 and Phila. Reg. V Flash Point: lOOF Packaging: 1 and 5 gallon cans Colors: White Important Information: 1. Do not use if air or surface temperature is below 50F (IOC) or if moisture condensation is present. 2. Apply LOK-TITE Stain Sealer over knots and stains before proceeding. 3. Refer to label for specific instructions and warnings. 4. A suitable rust inhibitive primer should be used on metal surfaces exposed to frequent condensation, high humidity or corrosive conditions. 5. Do not use directly over galvanized metal.

36

Prepaint w i a l t i e s and Surface Tolerant Coatings

M.A.

BRUDER

&

SONS, INC.:

FRESH KOTE Exterior Primer:

Oil-Alkyd High hiding primer designed to seal wood trim and siding. Dries to a smooth, low gloss finish which provides an excellent foundation for both latex and alkyd top coats. Recommended Uses: Exterior wood surfaces including trim and siding. Top Coat Recommended: FRESH KOTE House Paint (404 Line) or FRESH KOTE Latex House Paint (409 Line) Application Data: Method: Brush, roller or spray Type of Equipment: Nylon or bristle brush Synthetic roller cover Air or airless spray Thinner: M.A.B. Paint Thinner 090-032 or M.A.B. Naphtha 090-053 Theoretical Coverage: (Dry Film): 962 (Mil Ft. per Gallon) Theoretical Spreading Rate: (Dry Film): 480 sq. ft. per gal @ 2 mils (Allow IO-30% loss due to application & surface variables) Drying Time @ 70F: To touch...6-8 hours To recoat...18-24 hours (Allow more time at lower temperatures and high humidities) Specification Data: Gloss: Low Wt./Gallon: 10.9 lbs No. of Coats: One Viscosity: 93i2 K.U. Solids Content: Wt. 76% Vol. 60% Temperature Limit (Dry): Continuous...200F. Intermittent...275F. Environmental Codes: Conforms to all present environmental codes such as L.A Rule 66 and Phila. Reg. V Flash Point (open cup): 100F. Packaging: 1 Gallon Cans 5 Gallon Cans Colors: White

M.A. Bruder & Sons, Inc.

M.A.

BRUDER

&

37

SONS, INC.: FRESH KOTE Latex Exterior Primer:

Acrylic Latex A latex primer designed to seal exterior wood and to provide a uniform surface before finishing with FRESH KOTE Latex House Paint. Recommended Uses: As an undercoat for FRESH KOTE Latex House Paint on nonstaining wood surfaces. Top Coat Recommended: FRESH KOTE Latex House Paint (409 Line) Application Data: Method: Brush, roller or spray Type of Equipment: Nylon brush Synthetic roller cover Air or airless spray Thinner: Water Theoretical Coverage: (Dry Film): 593 (Mil Ft. per Gallon) Theoretical Spreading Rate: (Dry Film): 395 sq. ft. per gal. @ 1.5 mils (Allow 10-30% loss due to application & surface variables) Drying Time @ 70F: To touch ...A - 1 hour To recoat...2 - 4 hours (Allow more time at lower temperatures and high humidities) Specification Data: Gloss: Flat Wt./Gallon: 1 1 . 1 lbs No. of Coats: One Viscosity: 75+3 K.U. Solids Content: Wt. 53% VOl. 37% Temperature Limit (Dry): Continuous...225F. Intermittent...275F. Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 66 and Phila. Reg. V Flash Point (open cup): None Packaging: 1 Gallon Cans 5 Gallon Cans Colors: White


M. A. BRUDER & SONS CO.,

INC.:

High Performance (HIPAC) Systems:

PLY-TILE 520-W-45 Primer: Catalyzed epoxy primer for interior or exterior wood, masonry and non-ferrous metals. Excellent for priming aged epoxy and other hard, dense surfaces. Use to seal concrete and wood floors. Mix Ratio 1:l; Pot Life @ 70F: 8 hours. Vehicle: Epoxy-Polyamide % Solids by Volume: 49 Rec. Spread Rate sq. ft. per gal: 425 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4 - 6 Recoat: 18 - 24 RICH-LUX PRIME FAST: Premium quality, emulsion primer for walls and ceilings. Prevents "fuzzing" on dry wall. Allows priming on finishing on same day. Class "A" fire rating on non-combustible surfaces. Vehicle: Acrylic Vinyl Latex % Solids by Volume: 30 Rec. Spread Rate sq. ft. per gal.: 325 @ 1.25 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 1/4 - 1/2 Recoat: 2 - 4 RUST 0 LASTIC LEAD FREE PRIMERS, 073 Line: Extremely versatile, lead free primers providing excellent rust and corrosion resistance to clean or tight-rusted surfaces. RUST 0 LASTIC DAMP PROOF PRIMER: Vehicle: Alkyd-Fish Oil % Solids by Volume: 52 Rec. Spread Rate sq. ft. per gal.: 360 ( 2 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 2-4 Recoat: 18-24 RUST 0 LASTIC GRAY PRIMER: Vehicle: Alkyd % Solids by Volume: 44 Rec. Spread Rate sq. ft. per gal.: 375 (1.5 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 2-4 Recoat: 18-24 RUST 0 LASTIC HYDRO-PRIME: Vehicle: Acrylic Latex % Solids by Volume: 41 Rec. Spread Rate sq. ft. per gal.: 375 (1.5 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 1/4-1/2 Recoat: 2-4


M.A.

39

BRUDER I SONS, INC.: High Performance (HIPAC) Systems (Continued):

RUST 0 LASTIC Lead Free Primers, 073 Line(Continued): RUST 0 LASTIC Orange Primer: Vehicle: Alkyd % Solids by Volume: 54 Rec. Spread Rate sq. ft. per gal.: 375 (2 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 2-4 Recoat: 18-24 RUST 0 LASTIC White Primer: Vehicle: Alkyd % Solids by Volume: 42 Rec. Spread Rate sq. ft. per gal.: 375 (1.5 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 2-4 Recoat: 18-24 RUST 0 LASTIC Zinc Chromate Primer: Meets Federal Spec. TT-P-645 Vehicle: Alkyd % Solids by Volume: 45 Rec. Spread Rate sq. ft. per gal.: 385 (1.5 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 2-4 Recoat: 18-24 RUST 0 LASTIC Zinc Dust Primer: Meets Federal Spec. TT-P-641 Type I1 Vehicle: Alkyd % Solids by Volume: 50 Rec. Spread Rate sq. ft. per gal.: 425 (1.5 mil) Drying Time: Hours @ 70F, 50% R.H.: Touch: 6-8 Recoat: 18-24 VINYL WASH PRIMER: Chemical pretreatment for galvanized, ferrous and non-ferrous metal to insure adhesion of subsequent coats. Bonds effectively to chromate-treated galvanized surfaces. Meets Federal Spec. DOD/ P/153280. Mix Ratio, 1 part acid component to 4 parts primer. Pot Life @ 70F: 8 Vehicle: Polyvinyl Butyral % Solids by Volume: 12 Rec. Spread Rate sq. ft. per gal.: 350 @ 0.3 mil Drying Time: Hours @ 70F, 50% R.H.: Touch: 114 - 1 1 2 Recoat: 1 - 2

40

I.A.

Prepaint Sptxialties and Surface Tolerant Coatings

BRUDW

&

SONS CO., INC.:

Interior Coating Systems:

FRESH KOTE Alkyd Enamel Undercoater: Easy flowing base coat for gloss and semigloss finishes. Vehicle: Alkyd % Solids by Volume: 5 2 Rec. Spread Rate sq. ft. per gal.: 4 5 0 @ 1 . 5 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 2-4 Recoat: 1 8 - 2 4 FRESH KOTE Vinyl Primer: Quick dry pigmented sealer for dry wall, plaster and concrete. Vehicle: Acrylic Vinyl Latex % Solids by Volume: 2 9 Rec. Spread Rate sq. ft. per gal.: 3 0 0 @ 1 . 5 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 1 / 4 - 1 / 2 Recoat: 2 - 4 RICH-LUX ENAMEL UNDERCOATER: Quick drying undercoater for new or previously painted wood surfaces. Fast recoat time permits finishing on same day. Vehicle: Acrylic Vinyl Latex 8 Solids by Volume: 3 4 Rec. Spread Rate sq. ft. per gal: 3 5 0 @ 1 . 5 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 1 / 4 - 1 / 2 Recoat: 2 - 4 RICH-LUX PRIME FAST: Premium quality, emulsion primer for walls and ceilings. Prevents "fuzzing" on dry wall. Allows priming and finishing on same day. Class "A" fire rating over non-combustible surfaces. Vehicle: Acrylic Vinyl Latex % Solids by Volume: 3 0 Rec. Spread Rate sq. ft. per gal.: 3 2 5 @ 1 . 2 5 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 1 / 4 1/2 Recoat: 2 4 RICH-LUX Sealer Undercoater: High-hiding, pigmented primer and sealer for wood and plaster. Exhibits excellent holdout under architectural enamels and gloss paints. Vehicle: Alkyd % Solids by Volume: 4 9 Rec. Spread Rate sq. ft. per gal.: 4 3 5 @ 1 . 5 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 1 - 2 Recoat: 18 - 2 4 RICH-LUX W o o d Sealer: Ideal sealer for all types of wood and as an undercoater for RICH-LUX Urethane Wood finishes: Vehicle: Alkyd Urethane % Solids by Volume: 2 4 Rec. Spread Rate sq. ft. per gal.: 3 0 0 @ 1 . 0 mils Drying Time: Hours @ 70F, 5 0 % R.H.: Touch: 1 - 2 Recoat: 8 10

-

-

-


M. A. BRUDER & SONS CO., INC.: (Continued1:

41

Interior Coating Systems

FRESH KOTE Exterior Primer: High hiding primer designed to seal wood trim and siding. Dries to a smooth finish which provides an excellent foundation for both latex and alkyd topcoats. Vehicle: Oil-Alkyd % Solids by Volume: 60 Rec. Spread Rate sq. ft. per gal.: 400 @ 2 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 6-8 Recoat: 18-24 MINIT DRI Clear Sanding Sealer: Quick dry sanding sealer for unpainted interior woodwork. Maintains color of light woods, brings out natural beauty of wood grain and provides a foundation for various finishes. Vehicle: Vinyl Toluene % Solids by Volume: 32 Rec. Spread Rate sq. ft. per gal.: 350 @ 1.25 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 5-10 min. Recoat: 3-4 PLY-THANE 540 Primer: One package urethane primer designed to adhere to difficult surfaces such as factory finishes, glass, fiberglass. Suitable under alkyd and latex finishes. Vehicle: Oil Modified Urethane % Solids by Volume: 46 Rec. Spread Rate sq. ft. per gal.: 425 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 1-2 Recoat: 18-24 PLY-TILE 520-W-45 Primer: Catalyzed epoxy primer for interior or exterior wood, masonry and non-ferrous metals. Excellent for priming aged epoxy and other hard, dense surfaces. Use to seal concrete and wood floors. Mix Ratio 1:l; Pot Life @ 70F: 8 hours. Vehicle: Epoxy Polyamide % Solids by Volume: 49 Rec. Spread Rate sq. ft. per gal.: 425 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4-6 Recoat: 18-24

42

Prepaint *ecialties and Surface Tolerant Coatings

M. A. BRUDW 8 SONS CO., INC.: (Continued):

Interior Coating Systems

QW 26 Floor Sealer: Penetrating sealer for commercial wood or concrete floors. Resists impregnation of grease, oil and dirt. Vehicle: Alkyd Urethane % Solids by Volume: 21 Rec. Spread Rate sq. ft. per gal.: 275 @ 1.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 1-2 Recoat: 4-6 RICH-LUX Clear W o o d Sealer: Ideal sealer for all types of wood and as an undercoater for RICH-LUX Urethane Wood Finishes. Vehicle: Alkyd Urethane % Solids by Volume: 24 Rec. Spread Rate sq. ft. per gal.: 300 @ 1.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 1-2 Recoat: 8-10 SEA SHORE Latex Primer: Highest quality latex primer for use with SEA SHORE Finishes. Specially formulated for staining type woods. Minimizes discoloration of finish coats. Vehicle: Acrylic Latex % Solids by Volume: 37 Rec. Spread Rate sq. ft. per gal.: 350 @ 1.5 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: f - 1 Recoat: 2 - 4 SEA SHORE Primer: Premium quality oil based primer for exterior wood. Can be topcoated with alkyd or latex type finish coats. Vehicle: Oil-Alkyd % Solids by Volume: 61 Rec. Spread Rate sq. ft. per gal: 475 @ 2.0 mils Drying Time: Hours @ 70F, 50% R.H.: Touch: 4-6 Recoat: 18-24


M.A.

BRUDER & SONS CO.,

INC.:

43

MINIT D R I Sanding Sealer:

A quick drying, easy sanding, clear sealer. Maintains the color of light woods and brings out the natural beauty of wood grains. Dries for sanding in 3 hours. Allows application of two ( 2 ) coats the same day. Provides an excellent foundation for clear or pigmented finish coats. Uses : All types of unfinished interior wood surfaces - including plywood. Ideal for trim, doors, paneling, cabinets, woodwork, etc. Use only on new wood or wood surfaces from which old finishes have been removed. Surface Preparation: Sand wood surface smooth. Wipe with tac rag and/or vacuum to remove all dust. If desired before applying sealer, stain and fill open grain woods with RICH-LUX Wood Stain and M.A.B. PASTE WOOD FILLER. Directions: Stir thoroughly before using. Application: Brush: Apply Sealer liberally in an even coat. Spray: Thin Sealer up to 25% with M.A.B. Paint Thinner. After Sealer has dried approximately 3 hours, sand with a fine or medium fine grade of paper. Wipe clean or "tac rag" and apply finish coat of varnish or other Architectural Finish. Note: If a semi-gloss rubbed effect is desired, a second coat of M.A.B. SANDING SEALER may be applied as a finish. Spreading Rate: 700 to 800 square feet per gallon. Dry Time: Dry to sand and recoat three ( 3 ) hours. Clean Up: Use M.A.B. Bath.

Paint Thinner or M.A.B.

Brush and Roller

44


M.A.

BRUDER 8 SONS, INC.: (Epoxy-Polyamine):

-

PLY-MASTIC 101 EPOXY Mastic Coating

Proven Field Performance Excellent Corrosion Resistance Very Low V.O.C. High Build High Solids Easy Application A uniquely formulated high performance mastic designed to exclude corrosion producing moisture from the steel/coating interface by forming a hard barrier-like film. Forms a tenacious bond to blast cleaned or firm rusted steel. PLY-MASTIC cures to a very durable semi-gloss finish which is highly resistant to salt air, high humidity, fresh and salt water immersion and other corrosive atmospheric pollutants. High build capability gives superior edge protection and extra film thickness where needed. Standard and low temperature activators are available allowing application from 30 to 90F. Recommended Uses: Use on blast cleaned, for best performance, or firm rusted steel where abrasive blasting is restricted or impractical. Suitable as a one coat maintenance system or as a primerlintermediate under high performance coatings. Use also to upgrade previously painted surfaces in good condition. Recommended Top Coats: High performance finish coats such as 2 package urethanes and epoxies, or vinyls and industrial latexes. Technical Data: Activator Type: Standard (761056): Application Conditions: 50-90F Theoretical Coverage (sq. ft. per gal. Dry Mil): 1444 Recommended DFT per coat: 5-7 mils Mixing Ratio (By Vol.): 3 Parts A: 1 Part B Solids Content, Wt/Vol. %: 94/90 VOC (lbs/gal) as supplied: -73 at Spray Application: 1.2 at Brush/Roller Appli.: 1.4 Weight/Gallon (lbs.): 12.2 Flash Point F (SETA): 140 Activator Type: Low Temperature (761057): Application Conditions: 30-55F Theoretical Coverage (sq. ft. per gal. Dry Mil): 1421 Recommended DFT per coat: 5-7 mils Mixing Ratio (By Vol.): 3 Parts A: 1 Part B Solids Content, Wt/Vol. %: 93/89 VOC (lbs/gal) as supplied: .83 at Spray Application: 1.4 at Brush/Roller Appli.: 1.8 Weight/Gallon (lbs.): 11.8 Flash Point F (SETA): 124 Colors: White, Aluminum and Industrial Color Guide Groups 4,5,6 Environmental Codes: Conforms to existing V.O.C. Regulations.


M.A.

45

BRUDER 8 SONS, INC.: PLY-MASTIC 101 Epoxy Mastic Coating (Epoxy-Polyamine)(Continued):

Thinning (per mixed gal): Standard: Brush, Roller, Airspray: 1 to If pints Xylol Airless Spray: 1 to 14 pints Toluol Low Temperature: Brush, Roller, Airspray: 1 to 14 pints Xylol Airless Spray: f to 1 pint Toluol Working Pot Life: (Hours) (4 Gallon Mixed Product, Thinned for Application) Standard: 30F: NR 70F: 3; 50F: 8 90F: 13 Low Temperature: 30F: 23 50F: If 90F: NR 70F: NR Drying Times (Hours for 5 Mils DFT): To Touch: Standard : 90F: 3-4 70F: 6-8 50F: 24-30 Low Temperature: 90F: NR 70F: NR 50F: 4-6 Dry Through/Recoat (Minimum Time): Standard : 90F: 8-16 70F: 16-24 50F: 48-72 Low Temperature: 90F: NR 70F: NR 50F: 16-24 NR

-

30F: NR

30F: 16

30F: NR 30F: 36-48

Not Recommended

Performance Data: Abrasion: 75-85 mg. loss Adhesion: 400-500 psi at break Accelerated Weathering, QUV: 1000 hours: No through rusting, blistering or loss of adhesion Chemical Resistance: Very good resistance to splash and spillage of aqueous solutions of mineral acids (sulfuric, hydrochloric) and caustics (sodium and ammonium hydroxide). Field Performance: Passed 3 year field test on a Florida Test Bridge in a salt air environment. Flexibility: No cracking or loss of adhesion. Food Contact: USDA authorized for incidental food contact. Humidity: 1000 hours: No throuqh rustinq, blisterinq or loss of adhesion Immersion, Salt & Fresh Water;. Passes two years immersion in both fresh and salt water. Impact: 24 in. lbs. direct. Pencil Hardness: 7H Salt Spray (Fog): 1000 hours, no through rusting or blistering

46

M.A.



RICH LUX Enamel Undercoater(A1kyd):

Highly pigmented, odor-free flat undercoater made for use under architectural enamels. Possesses excellent hiding, leveling and enamel holdout on new or previously painted wood. Recommended Uses: For interior wood surfaces. Top Coat Recommended: Any interior alkyd or latex finish. Technical Data: Theoretical Coverage: 785 sq. ft. per gal. per dry mil Recommended Dry Film Thickness: 1.5 mils per coat Drying Time @ 70F, 50% R.H.: To touch: 1-2 hours To recoat: 18-24 hours Thinner: Brush & Roll: Paint Thinner, up to 5% Spray: Naphtha, up to 1 0 % Gloss: Flat Wt/Gallon: 11.9 lbs. Viscosity: 87 K.U. Solids Content: Wt. 73% Vol. 49% Temperature Limit (Dry): 225-275F Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 66 and Phila. Reg. V Flash Point: lOOF Packaging: 1 and 5 gallon cans Colors: White Important Information: 1. Do not use if air or surface temperature is below 50F (10'2) or if moisture condensation is present. 2. Apply LOK-TITE Stain Sealer over knots and stains before proceeding. 3. Refer to label for specific instructions and warnings.


M. A. BRUDER & SONS CO., (Acrylic Latex):

47

INC.: RICH-LUX Latex Enamel Undercoater

Quick drying undercoater for new or previously painted interior wood surfaces. Fast recoat time permits finishing on same day. Excellent enamel holdout over new wood. Recommended Uses: As an undercoater for both painted and unpainted wood. Top Coat Recommended: Any interior gloss, semi gloss or low luster finishes. Technical Data: Theoretical Coverage: 550 sq. ft. per gal. per dry mil Recommended Dry Film Thickness: 1.5 mils per coat Drying Time @ 70F, 50% R.H.: To touch: 114 - 112 hr. To recoat: 3 - 4 hours Thinner: Water Gloss: Flat Wt/Gallon: 11 .O lbs. Viscosity: 93 K.U. Solids Content: Wt. 50% Vol. 34% Temperature Limit (Dry): 225-275F Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 6 6 and Phila. Reg. V Flash Point: None Packaging: 1 and 5 gallon cans Colors: White Important Information: 1. Do not use if air or surface temperature is below 50F (1OC) or if moisture condensation is present. 2. Apply LOX-TITE Stain Sealer over knots, stains and bleeding woods before proceeding. 3 . Refer to label for specific instructions and warnings.


M.A.


RUST-0-LASTIC HYDRO-PRIME:

Acrylic resin emulsion. A first quality anti-corrosive primer designed for use on ferrous, galvanized and other non-ferrous metals. It is water thinnable, non-flammable, non-toxic and odorless. Under normal drying conditions, finish coats may be applied after 3 0 minutes drying time.

Recommended Uses: Primer for tanks, piping, metal and transite shed and warehouse structures, railroad cars, highway and bridge construction, galvanized ducts and ceilings. Top Coat Recommended: RUST 0 LASTIC Finish Coats; oil, alkyd or latex finishes. Application Data: Method: Brush, roller or spray Type of equipment: Nylon brush Synthetic roller cover Air or Airless equipment Thinner: Not required. Theoretical Coverage: (Dry Film): 690 Mil Ft. per gallon Theoretical Spreading Rate: 300 sq. ft. @ 2 Mils Drying Time @ 70F: To touch.. - 1 0 minutes To recoat...30 minutes Specification Data: Gloss: Flat Wt./Gallon: 1 1 . 4 lbs. No. of Coats: One Viscosity: 78i3 K.U. Solids Content: Wt. 59.0% Vol. 4 3 . 0 % Temperature Limit (Dry): Continuous...200F Intermittent...225F Environmental Codes: Conforms to L.A. Rule 66 and Phila. Reg. 5 concerning air pollution. Flash Point (open cup): None Packaging: 1 gallon cans 5 gallon cans Colors: White


M.A.


49

RUST 0 LASTIC Vinyl Wash Primer:

Polyvinyl-Butyral

Interior and Exterior

A pre-treatment, consisting of a vinyl butyral resin and acid diluent, for promoting adhesion to galvanized as well as ferrous and non-ferrous metals. Recommended Uses: As a pre-treatment to promote adhesion on galvanized, ferrous and non-ferrous surfaces prior to the application of priming coats. Particularly effective in bonding to galvanized surfaces that have been mill treated with chromate or other type inhibitors. Top Coat Recommended: Any M.A.B.

Primer and Top Coat.

Application Data: Method: Spray preferred, but may be brushed. Type of Equipment: Nylon brush. Air or airless spray. Thinner: M.A.B. Proprietary Solvent 090-036 Theoretical Coverage: (Dry Film): 192 (Mil Ft. per Gallon) Theoretical Spreading Rate: (Dry Film): 481 sq. ft. per gal. @ 0.4 mils (Allow 10-30% loss due to application & surface variables) Drying Time @ 70F: To touch. ..l/4 - 112 hours To recoat.. .1 - 2 hours (Allow more time at lower temperatures) Specification Data: Gloss: Low Wt./Gallon: 7.6 lbs Pot Life @ 70F: Loses effectiveness after 8 hours. No. of Coats: One Viscosity: 70k5 K.U. Mixing Ratio: 4 parts A to 1 part B by volume Solids Content: Wt. 21% VOl. 11% Temperature Limit (Dry): Continuous...l5OF Intermittent...ZOOF Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 66 and Phila. Reg. V Flash point (open cup): 63F Packaging: 5 Gallon Kit, consisting of 4 Gallon Primer and 1 Gallon Acid Diluent. Colors: Yellowish Green

50

M.A.


BRUDER CO.,

INC.:

SEA SHORE Latex Primer:

Acrylic Latex High quality wood primer for use with latex house and trim paints. Specially formulated for staining type woods such as redwood, cedar, mahogany and fir plywood. Minimizes discoloration of finish coats. Recommended Uses: For cedar, redwood, mahogany, fir plywood and other staining and non-staining woods. Topcoat Recommended: SEA SHORE or FRESH KOTE Exterior Paints. Application Data: Method: Brush, roller or spray. Type of Equipment: Nylon brush. Synthetic roller cover. Air or airless spray. Thinner: Water Theoretical Coverage: (Dry Film): 576 (Mil Ft. per Gallon) Theoretical Spreading Rate: (Dry Film): 385 sq. ft. per gal. @ 1.5 mils (Allow IO-30% loss due to application & surface variables) Drying Time @ 70F: 1 hour To touch To recoat.. .l-2 hours (Allow more time at lower temperatures and high humidities)

...&

Specification Data: Gloss: Flat Wt./Gallon: 10.5 lbs. No. of Coats: One or Two Viscosity: 82?4 K.U. Solids Content: Wt. 49% Vol. 36% Temperature Limit (Dry): Continuous...225F. Intermittent...275F. Environmental Codes: Conforms to all present environmental codes such as L.A. Rule 66 and Phila. Reg. V Flash Point (open cup): None Packaging: 1 Gallon Cans 5 Gallon Cans Colors: White (056-958) Gray (056-277)

SamuelCabot Inc.

SAMUEL CABOT INC.:

51

CABOT Stains:

PROBLEM-SOLVER Primer: Cabot's Problem-Solver Primer is an oil-based, flat white exterior primer specially formulated to provide superior resistance to extractive bleeding, mildew and moisture problems. This premium-quality, penetrating primer contains a special blend of oil and resin to achieve maximum durability. As the ideal base coat for Cabot's O.V.T. and Acrylic Solid Color Stains, as well as other solid stains and paints, Cabot's PROBLEM-SOLVER Primer provides superior performance on exterior siding, doors and trim. Extremely easy to apply, it also provides excellent adhesion to all new wood surfaces, as well as other previously stained and painted surfaces. Cabot's PROBLEM-SOLVER is recommended for use on extractiveprone wood species such as Red Cedar, Redwood and Douglas Fir and on all wood types including clapboards, shingles, manufactured hardboards, smooth and roughsawn surfaces. Composition & Regulation Compliance: An exterior primer based on natural oils and synthetic resins. This primer is in compliance with VOC requirenments for Specialty Architectural Coatings. Color : Available in White only. Tinting-maximum 4 ounces of compatible universal tinting colors. Physical and Chemical Data: Viscosity: 70-75 KU Flash Point: Over 100F TTP-141 method 4293 closed cup Finish: Dries to a uniform dull finish--may be recoated in 12 hours Dry Film Thickness: Approximately 2 mils Drying Time: (70-80F, 50% R.H.) Tack Free 6-10 hours. Allow at least 24 hours drying time before applying top coat Color: White Covering Capacity: Over smooth surfaces, 400-500 sq.ft. per gallon. Over rough surfaces; 150-250 sq. ft. per gallon. Spread rates are approximate and may vary upon surface porosity.


SAMUEL CABOT INC.:

Stains(C0ntinued):

PROBLEM-SOLVER Wood Cleaner # 8 0 0 2 : Cabot’s PROBLEM-SOLVER Wood Cleaner is specially formulated to remove mildew, mold, algae, dirt and other foreign matter from all painted, stained, unfinished or weathered wood surfaces. Unlike other mildew cleaners, this easy-to-use Cabot product does not require the addition of bleach in order to be effective. Use of routine cleaning and for properly preparing all surfaces prior to staining or restaining. Recommended Uses: For Use On: Exterior Wood Decks Siding - Fences Steps All Coated Surfaces, including aluminum, stucco and cement.

-

-

-

Physical and Chemical Data: Chemical Composition: Contains Calcium Hypochlorite and Sodium Metasilicate Appearance: Cloudy white viscous liquid. Weight per Gallon: 8.6 lbs. per gallon. Flash Point: None. This product is not flammable. Solubility: Readily dissolves in water. Freezing Point: 22F (-6C)

PROBLEM-SOLVER Wood Brightener #8003: Cabot’s PROBLEM-SOLVER Wood Brightener is formulated specifically to remove unsightly discoloration of wood caused by tannin bleed in extractive-prone wood species, such as cedar and redwood. It also removes nail and metal rust stains. This product can be used on all painted, stained and unfinished wood surfaces. Plus, when used on weathered wood, Cabot‘s PROBLEM-SOLVER Wood Brightener brings back the rich “new wood” look. Recommended Uses: For Use On: Exterior Wood Decks Siding - Fences - Railings Steps. Can also be used to remove rust stains on coated surfaces, including aluminum, stucco and cement.

-

Physical and Chemical Data: Chemical Composition: Contains Oxalic Acid. Appearance: Translucent blue liquid. Weight per Gallon: 8.5 lbs. per gallon. Flash Point: None. This product is not flammable. Solubility: Readily dissolves in water. Freezing Point: 30F (-1C)

Calbar, Inc.

CALBAR, INC.:

53

CALBEX Type P:

Heavy-Duty Industrial and Commercial Grade Chemical Resistant Wear Resistant Tile-Like Epoxy Coating Product Data: Color: Available in Clear, White, Colors Odor: None-cured Appearance: Hard, smooth, tile-like Gloss: Medium-High Solids: 50-60% (Varies with color) Viscosity: Brushing Application: Brush, Spray, Roller Coverage: 300-400 square feet per gallon Drying Time: Tack-free: 1-2 hours Recoat: 6-8 hours Curing: Overnight; Full-cure 1 week Pot Life: 8 hours; longer when reduced Inflammability: Flash Point 80F. wet Self Extinguishing dry Operating Temp.: -40 to 260F. These coatings are characterized by their outstanding resistance to many chemicals and solvents, excellent adhesion, flexibility, hardness, high impact and abrasion resistance. Used for industrial and institutional maintenance and construction; where "baked on" quality is desired from a room-temperature cured system. Can be applied to wood, metals, masonry, ceramics, glass. Application: Can be brushed or sprayed as mixed. Use ECT-1441 Thinner for any necessary thinning and for clean-up purposes. Spraying: Vacuum Cup: 35 to 45 p.s.i. air pressure Deposits 2 to 3 mils, dry film, on 1 overlapping pass. Use 10-20%, by volume, of ECT-1441 Epoxy Coating Thinner Pressure Feed: 5 to 10 p.s.i. fluid pressure 50 to 60 p.s.i. atomizing air Use up to 10% by volume, of ECT-1441, when required. Application Temperature: 5OF. to 110F. Spray gun and lines should be cleaned every 4 hours with ECT-1441 Thinner or preceding any lay-up period. Clean all equipment after use with ECT-1441 Thinner. Remaining unused coating mixture is reduced 20%, by volume, with ECT-1441 for overnight storage and added to a fresh mix the following morning. Unused portion should not comprise more than 20% of the fresh mix.


CALBAR, INC.:

NATIONAL TINNERS Paints:

SHOWER-PROOF: For coating over previously painted metal A fast-drying paint for coating and recoating metal roofs. It's "shower-proof" 30 minutes after application and dries in a few hours to a high gloss, tough, elastic, long-wearing coating. SHOWER-PROOF incorporates pure colors used in the formula, together with a specially treated durable liquid to insure permanent color and long service. Coverage: Approximately 400 ft2 per gallon, depending on surface and temperature conditions. Drying: It's "shower-proof" only 30 minutes after application; completely dry in a few hours. A second coat, if needed can be applied in 24 hours. Application: Brush in with a good quality brush. Neither rolling nor spraying recommended. SHOWER-PROOF is ideal for recoating Terne and other metal roofs. (On old Terne roofs, surface should be thoroughly washed with tri-sodium phosphate; bare spots brushed with a stiff bristle brush and coated with red TIN-0-LIN; and then the entire surface recoated.) TIN-0-LIN: For new Terne, bare spots, or over older TIN-0-LIN A slow-drying iron oxide paint ground and mixed in linseed oil. Red TIN-0-LIN serves as a primer for new Terne roofs, as well as a spot primer, and a finish coat. The linseed vehicle in TIN-0-LIN locks into metal pores forming a rust preventative bond...providing attractive protection over a long time period. Coverage: Approximately 400 ft2 per gallon, depending upon surface and temperature condition. Drying: Set touch--overnight; Tack-free--48 hours; Recoat-7 to 10 days. Surface Preparation: Surface must be free of oil, rust, dust, loose paint and any foreign matter that can interfere with adhesion, including moisture. Application: Must be brushed in well with a high quality brush of the type recommended for oil based paints. Spraying or rolling is never recommended. Avoid thick deposits. One coat of TIN-0-LIN is an excellent rust-inhibitive primer--followed by one or two finish coats, depending on color. Old Terne: A power wash with tri-sodium phosphate is recommended to remove all foreign matter, loose paint and scale. Bare spots should be well cleaned with a stiff bristle brush (never wire brush or metal scraper) and spot primed with red TIN-0-LIN. The entire roof can then coated with CALBAR SHOWERPROOF.

California Chemical Co. 55

CALIFORNIA CHEMICAL CO.: Heavy Duty STRIP: Industrial Parts Cleaner Cleans in MinutesILasts for Months STRIP is a high performance, industrial strength, cold parts cleaner. Its unique cleaning formula acts instantly on dirty, sludge clogged parts. STRIP is specially blended to attack heavy grease and carbon build up without weakening. STRIP'S active phase contains no water or aromatics that evaporate. You can use it month after month without replacement.

No Comparison No ordinary, watered down solvent cleaners or detergents can touch it. Yet STRIP is non-flammable, non-corrosive, and won't etch metals. Parts come out clean in just minutes without scrubbing, agitation or overnight soaking. Really tough problems like baked on carbon and oxidized oils strip off easily. Save 90% of Waste Disposal Cost STRIP does not have to be removed from your shop like other solvents. Use a simple 2 drum system to remove only the waste sludge until you have enough to dispose of. Once or twice a year clean out the dip tank, remove the sludge build up, and pour the STRIP back into the tank. That's it. You seldom have to dispose of the STRIP itself. Aviation Approved STRIP degreaser complies with Boeing document D6-17407, Douglas Aircraft Corp. CSD #1, and has met United Airlines requirements for safe cleaning of clad and bare aluminum, steel and magnesium parts. STRIP'S high performance formula cleans thoroughly without pitting, scarring or etching sensitive metals. Removes: Carbon, Grease, Oxidized oils, Heavy sludge, Tar, Gum, Lacquer, Varnish, Paint, Ethyl stains, Rubber, and just plain Dirt. Cleans: Carburetors, Transmissions, Aluminum, Engine parts, Blades, Gears, Rings, Valves, Cylinders, Machinery of all types, Aviation parts and equipment, Motorcycle, Truck and Vehicle parts.

56


CALIFORNIA PRODUCTS CORP.:

Acrylic Enamel Undercoat:

An excellent fast drying latex undercoater with exceptional hiding and self-leveling qualities. Its excellent adhesion properties make it ideal for usage over glossy coatings or previously varnished surfaces. This hard durable primer sealer gives maximum holdout for alkyd, acrylic latex or modified urethane top coats. Surface Uses: Plaster - Wallboard Gypsum Board

-

Wood Concrete Varnished Surfaces

Application: - Brush Roller

-

Spray Airless Spray

-

-

Drying Time: - Recoat--1 Hour under normal conditions Color Range: - White Only - Tintable with Universal Colorants Coverage:

-

400-450

square feet per gallon.

Limitations: - Do not use on bare metal. Do not use under 50F. Will raise grain slightly on open grain woods.

-

Specifications: 1 . New plaster, dry wall, composition board, wood, concrete:

1 Coat California Acrylic Enamel Undercoat 1 or 2 Coats California ALLSHEEN, RAY-0-GLOS or FULL-GLOS or 1 or 2 Coats California Alkyd Eggshell, Semi-Gloss or Gloss 2. Previously Painted Surfaces, Varnished Surfaces, Existing

Woodwork: 1 Coat California Acrylic Enamel Undercoat 1 Coat California ALLSHEEN, RAY-0-GLOS or FULL-GLOS or 1 Coat California Alkyd Eggshell, Semi Gloss or Gloss Product Specifications: Vehicle: 73% Pigment: 27% Weight/Gallon: 1 1 .l lbs. Flash Point: None

Solids by Weight: 45% Solids by Volume: 32% Thinner: Water

California Products Gorp.


57

ALLWALL Vinyl Acrylic Latex Flat:

Vinyl latex matte flat finish formulated for new or repaint work on interior wall and ceiling areas in homes, public institutions, and apartments, requiring a top quality coating. ALLWALL is alkali and moisture resistant, allowing it to be used as a self-priming finish over both new wallboard and plaster. This vinyl latex paint is self leveling, washable and quick drying as well as having excellent color retention and durability. Surface Uses: Plaster - Drywall - Wallboard Concrete - Masonry Block

-

Acoustical Surfaces Canvas Primed Metal Wood

Application: Brush - Roller

-

Conventional Spray Airless Spray

-

-

-

-

Drying Time: - 1 Hour for Recoat Color Range: - 20 Standard Colors - 620 Architectural Colors - Custom Colors--Factory Matched Coverage: - Brush or Roll 400-450 sq.ft./gal. 300-350 sq.ft./gal. 225-250 sq.ft./gal. - Spray: 180-200 sq.ft./gal.

on smooth surfaces

on absorbent surfaces on filled masonry block

Limitations: Do not apply below 50F. Do not use on unprimed metal. - Do not use as accent color on walls or woodwork to prevent burnishing.

-

Fire Rating: - Class A ASTM E84-70 Test Method Flame Spread - O/Fuel Contributed

-

Product Specifications: Vehicle: 59% Pigment: 41% Weight/Gallon: 12.0 lbs. Flash Point: None Solids by Weight: 55% Solids by Volume: 36% Thinner: Water

-

O/Smoke Density

-

0

58 Prepainr Specialties and Surface Tolerant Coatings


CAL GLAZE Block Filler:

An acrylic, silica free, easy flowing block filler with high binder content designed specifically to fill masonry block and concrete to be topcoated with epoxy polyesters, epoxies, urethanes and other heavy duty coatings. This block filler has excellent brushing and rolling qualities and gives maximum holdout for catalyzed coating topcoats. Ideal all purpose filler that helps prevent pinholes on both interior and exterior surfaces. Surface Uses: Masonry Block Light Aggregate Block Porous Concrete

-

Application: - Brush - Roller - Spray Drying Time 2 Hours for Recoat

-

Color Range: - White - Can be tinted with Universal colors Coverage: - Brush or Roll Masonry Block--225-250 square feet per gallon Light Aggregate Block--125-175 square feet per gallon - Spray All Surfaces--160 square feet per gallon Limitations: - Do not apply below 50F. Do not use as finish coat.

-

Specifications: Masonry block, light aggregate block, poured concrete: 1 Coat CALIFORNIA CAL GLAZE Block Filler 1 or 2 Coats CALIFORNIA CAL GLAZE Epoxy Polyester Urethane Enamel TILE COTE Epoxy Alkyd Eggshell, Semi Gloss, Gloss Acrylic Latex Flat, Eggshell, Semi Gloss, Gloss Product Specifications: Vehicle: 52% Pigment: 48% Weight/Gallon: 12.3 lbs. Flash Point: None


California Products Corp.


59

House Paint Primer Acrylic Latex:

A 100% acrylic latex formula specifically designed to neutralize "bleeding" stains that occur in wood types such as Cedar, Cypress and Redwood. This mildew resistant primer is formulated without lead or mercury and immobilizes staining by chemical interaction within the formulation. Wood primer provides excellent adhesion to all bare wood surfaces and previously painted discolored wood surfaces before application of finish coats. Surface Uses: - New Wood Clapboards - Shingles - Shakes

-

Application: - Nylon or Prone1 Brushes Roller

-

-

-

-

Novelty Siding Stained Wood--Before Repaint Plywood--Exterior and Interior Trim

- Conventional Spray Airless Spray

Drying Time: 4 Hours--Normal Drying Conditions - Primer may initially appear "soft" due to the curing process but can be safely recoated.

-

Color Range: White and Grey - Tintable with Universal Colorants

-

Coverage: - 400 square feet on bare wood 4 5 0 square feet on previously painted surfaces - 300 square feet on striated shakes

-

Limitations: - Do not apply when temperature is under 50F. - Under deep colors--use grey primer. - Heavy staining may require a second coat of primer. - Do not use over chalky surfaces--poor adhesion will result. - Knots on trim should be sealed before wood is primed. Product Specifications: Vehicle: 5 4 . 3 % Pigment: 4 5 . 7 % WeightIGallon: 1 2 . 3 lbs. Flash Point: None Solids by Weight: 5 1 % Solids by Volume: 39% Thinner: Water

60 Prepaint m i a l t i e s and Surface Tolerant Coatings


KOTALL Alkyd Primer-Sealer:

A pigmented Alkyd Primer-Sealer designed to seal highly absorbent interior wall surfaces that will be topcoated with Eggshell, Semi-Gloss or Gloss Enamels. KOTALL Primer-Sealer has a high binder content and provides an excellent vapor barrier when applied on the interior surface of exterior walls of plaster, sheetrock or wallboard. Surface Uses: - Plaster - Sheetrock

-

-

Wallboard Composition Board

Application: - Brush - Roller--Short Nap Conventional or Airless Spray

-

Drying Time: Touch--4 hours Recoat--24 hours

-

Specific Moisture Permeability: - ASTM D1653 Method 0.16.....0.85

Perms

Color Range: White only

-

Coverage: 250-400 square feet per gallon dependent on surface porosity

-

Limitations: - Do not apply to plaster with high moisture content. - Allow plaster to dry properly to below 15% moisture content. - Inadequate ventilation will increase drying time required before finish coat can be applied. Specifications: 1.0 Unfinished plaster, sheetrock, composition board, wallboard: 1 coat CALIFORNIA KOTALL Alkyd Primer-Sealer. 1 or 2 coats CALIFORNIA Alkyd, Acrylic Latex or Modified Urethane in sheen desired. 2.0 Previously finished surfaces: With large patches, same as above. Product Specifications: Vehicle: 46.84% Pigment: 53.16% Weight/Gallon: 11.60 lbs.

Solids by Weight: 72.44% Solids by Volume: 50.70% Flash Point: 103F


CALIFORNIA PRODUCTS CORP.: Masonry Sealer:

61

LACRYLIC Acrylic Lacquer Clear

A clear non yellowing acrylic lacquer which resists water, alkalis, weak acids and most detergents. LACRYLIC seals exterior concrete and masonry to retard water penetration and prevents dusting of concrete floors. This clear abrasion resistant coating can also be used as a durable finish over flagstone and terra cotta. Colorless LACRYLIC will prevent oxidation and discoloration on metal surfaces. It can also be used as a primer to deter water soluble stain in bricks that are to be painted with latex paints. Surface Uses: Masonry stucco Flagstone Brick, Common cation: Brush Spray

-

-

Clean Metal Tile Concrete Floors Wood

-

Airless Spray Floor Applicator

Drying Time: - 30-60 Minutes Color Range: - Clear--Non Yellowing Coverage: - Porous Surfaces 100-125 square feet per gallon Smooth Surfaces 150-175 square feet per gallon

-

Limitations: - Apply to dry surfaces. - Provide good ventilation. - Material will not bridge gaps or voids in masonry blocks. - Do not use on floors subjected to continued solvent or oil spillage Do not use below 40F.

-

.

Product Specifications: Vehicle: 100% Pigment: 0% Weight/Gallon: 7.0 lbs. Flash Point: 103F TCC

Solids by Weight: 17.7% Solids by Volume: 13.1% Thinner: Mineral Spirits/Ketone (Exempt Under EPA Organic Solvent Regulations)

62 Prepaint SpeCMlties and Surface Tolerant Coatings


LARCOMID Alkyd Enamel Undercoat:

An all purpose Alkyd Enamel Undercoater formulated to prime interior wood or metal. Material is designed to seal surfaces and sand smoothly so that finish coats of latex or alkyd will have a good even sheen and superior appearance. Surface Uses: Woodwork Cabinets - Clean Metal

-

-

-

Back Priming Furniture Plaster Wallboard

Application: - Brush Roller - Spray

-

Drying Time: - Overnight for Recoat Color Range: White Only - Can be tinted with Universal Colorants

-

Coverage: - 350-400 square feet per gallon Limitations: - Knots and resinous wood should be stain sealed before undercoating. - Do not apply over damp surfaces. Do not apply below 40F. - Do not use as primer on galvanized metal. - Undercoat should be tinted to approximate shade of finish coat color. - Metals should be thoroughly cleaned of rust and mill scale.

-

Product Specifications: Vehicle: 41% Pigment: 5 9 % Weight/Gallon: 12.3 lbs. Flash Point: 107F TCC

Solids by Weight: 76% Solids by Volume: 55% Thinner: Mineral Spirits (Exempt under EPA Organic Solvent Regulations)



63

LARCOLOID Zinc Chromate Primer:

A rust inhibiting fast dry metal primer to be used for touch up of abraded metal finishes and on site priming of miscellaneous ferrous metals. Zinc Chromate sands well and presents a smooth surface for application of alkyd, urethane and latex finishes. Surface Uses: - Metal Trim - Primed Metal--Touch Up Angle Iron

-

-

-

Equipment TOOIS Rails and Piping

Drying Time: Recoat--2 Hours

-

Color Range: Primer--Yellow Green

-

Coverage: - 400-450 square feet per gallon Limitations: Do not apply to damp metal. Rust and mill scale must be removed before priming. Do not apply below 40F.

-

Specifications: Ferrous Metal: 1 Coat LARCOLOID Zinc Chromate Primer 1 or 2 coats CALIFORNIA Eggshell, Semi Gloss, or Gloss Alkyd Enamels Aluminum: 1 coat LARCOLOID Zinc Chromate Primer 1 or 2 coats CALIFORNIA Eggshell, Semi Gloss, or Gloss Alkyd Enamels Note: Rust, mill scale, grease and dirt must be removed from metal before priming. Product Specifications: Vehicle: 58.6% Pigment: 41.4% Weight/Gallon: 10.4 lbs. Flash Point: 107F TCC

Solids by Weight: 66% Solids by Volume: 46% Thinner: Mineral Spirits (Exempt Under EPA Organic Solvent Regulations)


CALIFORNIA PRODUCTS COW.: PLEXICOLOR Acrylic Silica Block Filler: An exterior acrylic block filler formulated to expertly fill small imperfections and pinholes in masonry block and porous concrete, before materials are topcoated. This mineral type filler contains fine silica aggregates which fill voids and prevent seepage from driving rains and snow. The acrylic binder gives an easy to apply, alkali resistant uniform surface capable of receiving all types of finish coats. PLEXICOLOR Block Filler is not water sensitive after application and its inherent flexibility gives it the finest characteristics available in an exterior block filler, far superior to cementitious and PVA block fillers.

Surface Uses: - Masonry Block Poured Concrete - Cast Stone

-

-

-

Precast Concrete Porous Brick Light Aggegate Block

Application: Roller--Long Nap Brush--Nylon or Polyester Bristle

-

Drying Time: - Recoat--1 Hour Color Range: - Offwhite Coverage: - 225 square feet per gallon--average Limitations: Do not apply below 50F. Must be topcoated--will not weather. - Maximum filling and uniformity require full coverage-unthinned. - Do not use over heavily chalked previous coatings.

-

Product Specifications: Vehicle: 48.1 % Pigment: 51 -9% WeightIGallon: 12.5 lbs. Flash Point: None

Solids by Weight: 70.6% Solids by Volme: 5 6 . 1 % Thinner: Water

California Products Corp. 65


PRO PAINT Flat Latex:

A very flat vinyl copolymer wall paint for usage on walls, ceilings and partitions. This professional heavy duty latex finish has good washability plus excellent hiding, leveling and touch up qualities desired for large scale projects in schools, apartments, and public institutions. PRO PAINT far exceeds the performance standards of competitive paints designed for heavy maintenance usage. This finish is self priming over most surfaces and is lead and mercury free.

Surface Uses: Drywall - Concrete - Masonry Block - wood

-

Application: Brush - Roller

-

-

-

-

Plaster Primed Metal stucco Composition Board Conventional Spray Airless Spray

Drying Time: Recoat--1 hour

-

Color Range: - 8 Standard Colors California's Architectural Colors - Factory Matched Colors

-

Coverage: Brush:

-

4 0 0 square feet per gallon on smooth surfaces

2252275 square feet per gallon on masonry block Spray: 180 square feet per gallon

Limitations: Do not apply below 50F. Do not use on unprimed metal. Wood and plaster should have Acrylic Enamel Undercoat as first coat.

-

Product Specifications: Vehicle: 57% Pigment: 43% Weight/Gallon: 12.1 lbs. Flash Point: None




SAFETY PRIME House Paint Primer:

An exterior oil base wood primer formulated to seal and prime all exterior wood surfaces that will be recoated with oil base or latex finish coats. Its long oil formulation gives good penetration of wood, resists stains, stops suction and prepares the wood for an even distribution of the finish coats. SAFETY PRIME is lead and mercury free and resists mildew

.

Surface Uses: Clapboards - Shingles Shakes - Trim

-

-

-

Sills Exterior Plywood Gutters Windows

Application: Brush Roller

-

Drying Time: - 24 Hours for Recoat Color Range: White and Gray

-

Coverage: - White and Gray Coverage: - 400-500 square feet per gallon Limitations: Do not apply under 50F. - Do not apply to damp surfaces. - Prime coats do not weather--finish coats should be applied within three months.

-

Product Specifications: Vehicle: 41% Pigment: 59% WeightIGallon: 12.0 lbs. Flash Point: 107F TCC

Solids by Weight: 82% Solids by Volume: 67% Thinner: Mineral Spirits (Exempt Under EPA Organic Solvent Regulations)



Spray Paints PrirnerlFinish:

All-purpose odorless flat and gloss acrylic latices specifically designed for dry fall-out when sprayed. Ideal for large areas such as warehouses, factories, and gyms. A washable one coat high hiding finish formulated for maximum atomization by airless and conventional spray. Self-priming except over ferrous metal. Surface Uses: Wood - Concrete - Masonry Block - Plaster - Sheet Rock

-

-

-

Primed Ferrous Metal Galvanized Metal Pipe Covering Composition Board

Application: Airless Spray - Conventional Spray

-

Drying Time: - 2 0 to 30 minutes Color Range: - White Factory Mixed Custom Colors

-

Coverage:

-

160-200 square feet on flat surfaces 1 0 0 square feet on masonry block

Limitations: Do not apply under 50F. - Do not use colors-in-oil for tinting - Do not apply to unprimed ferrous metal. - Sets up quickly--should not be brushed or rolled on large areas. - Do not use as primer for other paints.

-

Product Specifications: Spray Flat: Solids by Weight: 55% Vehicle: 52% Pigment: 48% Solids by Volume: 35% WeightIGallon: 12.4 l b s . Thinner: Water Flash Point: None Product Specifications: Spray Gloss: Vehicle: 75% Solids by Weight: 49% Pigment: 25% Solids by Volume: 35% WeightIGallon: 10.6 lbs. Thinner: Water Flash Point: None

67


CALIFORNIA PRODUCTS CORP.: STONITE Primer: InteriorhxteriorAcrylic Lacquer-Sealer: A clear solvent thinned acrylic lacquer sealer designed to condition dusting concrete, so that latex finishes can be applied. This alkali resistant primer also eliminates the need of acid ecthing on floors that are to be finished with latex or urethane floor paint. STONITE Primer is recommended as a sealer over powdery and chalky surfaces coated with cementitious paints, so that these surfaces can be recoated with latex or alkyd paints. Sealing of charred wood before repainting is another usage of this outstanding sealer. Surface Uses: Sealing: - Cementitious Paints - Powdery Concrete Concrete Floors

-

Application: - Brush - Roller

-

-

-

-

Charred Wood Water Soluble Finishes Asbestos Shingles stucco Floor Applicator Airless Spray

Drying Time: - 30 minutes--Touch 4 hours--Recoat

-

Color Range: - Clear Coverage: Porous Concrete 80-100 square feet per gallon - Tight Masonry 225-250 square feet per gallon

-

Limitations: Do not use on red brick--use LACRYLIC Do not use below 40F. - Will not seal loose paint.

-

Product Specifications: Vehicle: 100% Pigment: 0% Weight/Gallon: 6.7 lbs. Flash Point: 80F TCC

Solids by Weight: 7.5% Solids by Volume: 6 % Thinner: Mineral Spirits/Xylol (Not Exempt Under EPA Organic Solvent Regulations)


CALIFORNIA PRODUCTS CORP.: Oil Base:

STORM STAIN Universal Wood Primer

This special wood primer is formulated for use under STORM STAIN White and Pastel Solid Color Stains, either Linseed Oil or Urethane Latex Base. This white exterior base coat is designed to neutralize and help eliminate the natural tannin or sugar staining and discoloration produced by bare woods such as red cedar, redwood, fir, pine or white cedar. STORM STAIN Universal Wood Primer has excellent adhesion to all wood surfaces and is highly resistant to peeling. This unique formulation also helps to diminish the surface rusting of uncoated nails. Surface Uses: - Clapboards - Shingles - Shakes

-

Siding Trim Hardboard

Application: Brush Roller

-

Airless Spray..013 tip Conventional Spray

-

Drying Time: To Touch--Overnight Recoat--48 hours or longer

-

Color Range: - White Coverage: Brush or Roller--400 square feet per gallon - Spray--200 to 225 square feet per gallon

-

Limitations: - Remove all mildew before application. - Seal knots with STAINCURE or WIPE-OUT before priming. - Air and surface temperatures should be 40F or higher during application. - Prime coats do not weather well--Finish coats should be applied within 3 months. - Do not apply to smooth side clapboards without thorough sanding or weathering. Product Specifications: Vehicle: 44.8% Solids by Weight: 78.5% Pigment: 55.2% Solids by Volume: 60.4% Weight/Gallon: 12.0 lbs. Flash Point: 103F Finish Sheen-Flat 8+-2 @ 60 S.G. Solvent: Mineral Spirits

69


CALIFORNIA PRODUCTS CORP.: Latex:

STORM STAIN Wood Primer Acrylic

This special wood primer is formulated for use under STORM STAIN White and Pastel Solid Color Stains, either Linseed Oil or Urethane Latex Base. This white exterior base coat is designed to help eliminate the natural tannin or sugar staining and disoloration produced by bare woods such as red cedar, redwood, fir, pine or white cedar. STORM STAIN Acrylic Latex Wood Primer has excellent adhesion to all wood surfaces and is highly resistant to peeling. The unique formulation also helps to retard the surface rusting of uncoated nails. Surface Uses: Clapboards Shingles - Shakes

-

-

Siding Trim Hardboard


-

Airless Spray .017 tip Conventional Spray

-

Drying Time: To Touch--1 hour Recoat--4 hours

-

Color Range: White

-

Coverage: Brush or Roller--400 square feet per gallon Spray--200-225 square feet per gallon

-

Limitations: Remove all mildew before application. - Seal knots with STAINCURE or WIPE-OUT before priming. Air and surface temperatures should be 50F or higher during application. Prime coats do not weather well--Finish coats should be applied within 3 months. Wood must be thoroughly dry to reduce the possibility of water soluble bleeding. A second coat may be necessary on heavily stained areas.

-

Product Specifications: Vehicle: 76.5% Pigment: 23.5% Weight/Gallon: 10.6 lbs. Finish Sheen--Flat 8+-2 @ 60

Solids by Weight: 51.5% Solids by Volume: 38.5% Flash Point: None S.G.



71

Vinyl Primer-Sealer:

An all-purpose water-reducible vinyl latex for priming wall or ceiling surfaces to be topcoated with latex, alkyd or modified urethane finishes. Vinyl Primer-Sealer gives excellent holdout of enamels and fast recoatability. This product is not recommended as a wood primer. Surface Uses: - Plaster - Wallboard - Gypsum Board

-

Concrete Masonry Block Pipe Insulation


-

Spray Airless Spray

Drying Time: - Recoat--1 Hour under normal conditions Color Range: - White only Tintable with Cal Tints by customer

-

Coverage: - Porous Surfaces: 250-275 Square feet per gallon - Smooth Surfaces: 400-425 Square feet per gallon Limitations: - Do not use on bare ferrous metal. - Air and surface temperatures must be 50F during application and drying time. Not recommended as wood or plywood primer.

-

Specifications: 1.0 New or unfinished plaster, drywall, wallboard, concrete, masonry block: 1 coat CALIFORNIA Vinyl Primer-Sealer 1 or 2 coats CALIFORNIA Latex, Alkyd or Modified Urethane in sheen desired. Deep or Accent Colors will nearly always require two finish coats. Product Specifications: Vehicle: 71.01 % Pigment: 28.99% Weight/Gallon: 10.28 lbs.

Solids by Weight: 36.22% Solids by Volume: 21.69% Flash Point: None



WILBUR

&

WILLIAMS CLEAR SEAL Coating:

A clear chlorinated rubber coating primarily designed to be applied to finish troweled concrete when it is hard enough to walk on (1 to 2 hours) and/or immediately after the disappearance of the "sheen" of surface moisture. This coating cures, seals and hardens new concrete. CLEAR SEAL can also be used as a sealer and dustproofer on unfinished old concrete. Description: CLEAR SEAL is a transparent, quick drying, synthetic liquid which cures, seals, hardens and dustproofs interior or exterior concrete floors or slabs. Applied to newly poured concrete surfaces after finishing, it prevents rapid evaporation of the guaging water, providing an efficient and economical method of curing concrete. Use : CLEAR SEAL, applied approximately 1 to 2 hours after final troweling, eliminates the surface evaporation of guaging water with resultant hairline cracks. The proper moisture content, necessary for producing a dense, hard concrete surface, is held by the sealer. A second coat may be applied when desired, usually on completion of construction. CLEAR SEAL seals out construction stains and materially reduces the cost of cleaning up after work is completed. The speed and ease with which it is applied helps reduce curing costs. CLEAR SEAL is resistant to most acids and alkalies, aliphatic solvents, minerals, vegetable and animal oils, soaps, water and traffic abrasion. Catalog Number: WW-1054 Color: Clear Solids by Weight: 20% Volume Solids: 12% Weight per Gallon: 7.7 lbs. Coverage: New Concrete: Rough Concrete--250 Square feet per gallon Smooth Concrete--300 Square feet per gallon Old Concrete-Unfinished: Rough Concrete--300 Square feet per gallon Smooth Concrete--400 Square feet per gallon


73

CALIWRNIA PRODUCTS CORP.: WILBUR & WILLIAMS COMBATIT 1050 Red/ 1051 Gray Metal Shop Primer: Generic Type: Linseed/Alkyd Red Oxide Primer Exposure: Interior & Exterior Description: COMBATIT is a quality air dry red oxide rust inhibiting primer formulated with a linseedlalkyd resin base. This lead free shop primer is designed to meet the normal standard requirements of metal fabricators and on site field applications by contractors. Recommended Uses: Primer for properly prepared structural steel, sub-purlines, frames, tanks, equipment and miscellaneous iron exposed to normal atmospheric contamination. Maximum penetration and adhesion are achieved over sand blasted steel but a good bond is also obtained over power tooled steel. COMBATIT can be topcoated with any conventional alkyd, oil modified urethane or acrylic latex metal paint. Appearance: SatinIEggshell 15+-5 @ 60 Specular Gloss Solids by Volume: 44.6% Weight per Gallon: 10.8 lbs. Colors: 1050 Red11051 Gray Solids by Weight: 67.1% Maximum VOC Content: 450 grams per liter Application Information: Surface Preparation: Surfaces must be clean, dry and free of dirt, grease, mill scale, loose paint and other contaminants. Ferrous Metal: Commercial Blast Cleaned (SSPC-SPC) if at all possible. Minimum surface preparation would include Power Tool Cleaning (SSPC-SP3) or Hand Tool Cleaning (SSPC-SP2). Galvanized Metal: Pretreat with GRIP-COAT Vinyl Wash Primer to achieve proper adhesion. Thinner: Spray Application--W&W 2307 Brush or Roller Application--W&W 2305 Flash Point: 44F Seta Flash Coverage: Brush or Roll--300-400 sq.ft. per gallon Spray--150-250 sq.ft. per gallon Film Thickness: Wet: 3.0-3.5 mils Dry: 1.5-2.0 mils Primers & Finishes: Recommended primers should always be used for specified surfaces. Two finish coats are usually recommended over surgaces primed to achieve desired film thickness. Ferrous Metal: 1 coat--COMBATIT Metal Shop Primer 1 or 2 coats--WILBUR & WILLIAMS Alkyd Enamels TUF-QUIK Oil Modified Urethane Enamels RUST-STOP Acrylic Metal Paint


CALIFORNIA PRODUCTS CO.: WILBUR Acrylic Latex:

&

WILLIAMS Enamel Undercoat

General Information: Type: Acrylic Latex Enamel Undercoat Appearance: Matte Finish Recommended Uses: Primer over wallboard, wood plaster, sheetrock or areas to be recoated. Solids by Weight: 44.9% Volume Solids: 3 3 . 0 % Weight per Gallon: 11.1 lbs. Application Information: Surfaces: Wood, plaster, sheetrock, wallboard Surface Preparation: Remove all dust, dirt, grease, oil and other foreign matter. Sheetrock and wood should be sanded smooth and dusted. Plaster should be knifed free of nibs and protrusions. Primer: Material is a primer Application Method: Brush, roll or spray Number of Coats: One--Must be recoated Thinning: Apply full body--thin sparingly with water if necessary Coverage: Brush or roll--350 sq.ft. per gallon --200 sq.ft. per gallon Spray Drying Time: 1 hour--recoat Protective Properties: Not applicable--for use only as interior primer

CaliforniaProducts Corp.

CALIFORNIA PRODUCTS CORP.: WILBUR 8 WILLIAMS FRIGID COAT WW4800 White Cold Storage Gloss Enamel: A white high gloss enamel formulated for low temperature application in freezer rooms of food processing and allied industries. This alcohol-thinned product provides a safe, sanitary, self-priming finish to be applied at temperatures lower than 40F on interior walls, ceilings and racks in areas such as cold storage rooms, freezer installations and ice cream hardening rooms, without shutting down refrigeration. Solids by Weight: 57% Volume Solids: 46% Weight per Gallon: 9 . 4 0 lbs. per gallon. Application Information: Surfaces: Wood, metal, and sealed masonry Surface Preparation: Scrape off frost and ice so that bare surface is exposed. Primer: Self-priming. Application Method: Brush, roller, or spray. Number of Coats: One coat--1 mil dry film thickness. Thinning: Thin 4/1 with denatured alcohol or methyl alcohol. Coverage: Brush or roll--400-450 square feet per gallon Spray --250-275 square feet per gallon. Drying Time: Tack free--1 hour Recoat--2 hours Accepted for use on federally inspected meat product plants by U.S. Department of Agriculture, Meat & Poultry Division.

75


CALIFORNIA PRODUCTS CORP.: Vinyl Wash Primer:

WILBUR

&

WILLIAMS GRIP-COAT 6906

Generic Type: Polyvinyl Butyral Zinc Chromate Wash Primer Exposure: Interior & Exterior Description: A metal pretreatment or wash primer formulated for use on completely clean metal of all types, prior to the application of other coating systems. This two component primer is particularly suitable for application on steel, aluminum, copper, brass, zinc, chrome, tin plate, galvanized steel, and stainless steel. GRIP-COAT is primarily used to insure adhesion of subsequent topcoats. It is not intended as a permanent protective primer and should be topcoated as soon as possible. GRIP-COAT can also be used as a "tie-coat" or bonding coat over fiberglas and baked enamel primers or finishes which are to be topcoated with conventional or catalyzed finishes. Recommended Uses: Pretreatment of clean ferrous metal when strong surface adhesion is needed. Primer for aluminum, copper, chrome, stainless steel and galvanized steel surfaces. May also be used as a "tie-coat" for fiberglas, baked enamel finishes and over inorganic zinc primers. Recommended as a metal pretreatment for any coating system exposed to a strong acid environment or salt water immersion. Appearance: Flat 5+-1 @ 60 Specular Gloss Solids by Volume: 9.5% (Intermixed) Weight per Gallon: 7.5 lbs/gallon (Intermixed) Acceptances: Meets Federal Specification DOD-P-15328D Color: Translucent Greenish-Yellow Solids by Weight: 19.2% (Intermixed) Application Information: Surface Preparation: Unfinished Aluminum, Stainless Steel, Copper, Brass or Galvanized Metal: Solvent Cleaning (SSPC-SPl). Ferrous Metal: , ~ ~ ~ , > = , & ~ y "&-,= &@-L,& 11 &?.hX,k cL.ym:cnq . : g < x - sp.l&!,; Non-Immersion Service: "Commercial" Blast Cleaning (SSPC-SP6) Baked Enamel Primer and Finishes: Must be clean of all oil, grease, dirt and other foreign material. Thinner: Isopropyl Alcohol or Denatured Alcohol Coverage: 750-800 sq.ft. per gallon--Spray application Flash Point: 55F Seta Flash Film Thickness: Wet: 2.0 mils Dry: 0.3 mils Primers & Finishes: GRIP-COAT is used as a primer over many unfinished metals and other surfaces that coatings do not normally adhere to properly. GRIP-COAT is applied at 0.3 to .05 mils dry and is not intended to be a corrosion resistant primer, so that a suitable rust inhibiting primer must be applied over it.


CALIFORNIA PRODUCTS CORP.: WILBUR 7010 Masonry Conditioner:

&

77

WILLIAMS MASON-COTE Sealer

Generic Type: Solvent Acrylic Exposure: Interior & Exterior Description: MASON-COTE is a clear, penetrating, solvent acrylic with many diversified uses as a sealer, primer and damproofer. Powdery or dusty masonry surface including concrete floors can be sealed and dustproofed with this clear alkali resistant product. Recommended Use: For use on brick, concrete, wood, plaster and asbestos shingles. Excellent for selaing chalky paints or "smokey odors" on wood. MASON-COTE makes an excellent damproofer over unfinished brick or concrete. Aged asbestos shingles or stucco surfaces that show signs of surface deterioration must be sealed with MASON-COTE prior to topcoating. Appearance: Clear finish Solids by Weight: 7.4% Weight per Gallon: 6.7 lbs. (average) Acceptances: U.S.D.A. approval-pending Colors: Clear Solids by Volume: 6% Application Information: Surface Preparation: Remove all dirt, dust, loose mortar, grease, oil and other contaminants from the surface. Holes and cracks should be filled and patched. Allow new masonry to cure for 30 days before using MASON-COTE Masonry Conditioner. Thinner: W&W 2 3 0 8 Reducer Coverage: Brick: 1 5 0 - 2 5 0 sq.ft. per gallon Concrete: 1 5 0 - 2 5 0 sq.ft. per gallon Stucco: 1 0 0 - 1 2 5 sq.ft. per gallon Porous Masonry: 100-125 sq.ft. per gallon Flash Point: 80F Setaflash Primers & Finishes: Asbestos Shingles--Stucco: 1 coat --MASON-COTE Masonry Coating 1 or 2 coats--MASON-COTE Masonry Coating Calcimine: 1 coat --MASON-COTE Masonry Conditioner 1 or 2 coats--KOTALL Alkyd Flat Enamel Brick or Concrete: Sealer Only: 1 or 2 coats--MASON-COTE Masonry Conditioner Walls: 1 coat --MASON-COTE Masonry Conditioner 1 or 2 coats--MASON-COTE Masonry Coating Floors: 1 coat --MASON-COTE Masonry Conditioner 1 or 2 coats--TUF-QUICK Urethane Floor Enamel


CALIFORNIA PRODUCTS CORP.: WILBUR EL WILLIAMS PRIME LINE 1703 Red/ 1704 Gray Universal Metal Primer: Generic Type: Phenolic Modified-Alkyd Primer Exposure: Interior & Exterior Description: A fast-drying, lead free phenolic modified alkyd, rust inhibitive primer. Universal Metal Primer can be applied to structural steel or other ferrous metal and will accept a variety of corrosion and chemical resistant top coats. PRIME LINE Universal Metal Primer is especially advantageous when used on ferrous metal that will be exposed for prolonged periods of time on job sites before top coating. Recommended Uses: Priming structural steel, tanks and piping. Well suited for fabricating shops and OEM applications, where the generic type of finish coat is unknown. May also be used as a barrier coat between conventional finishes and specialized top coats. Appearance: Eggshell Finish 15F+-5F @ 60F Specular Gloss Solids by Volume: 36.9%+-1.0% Weight per Gallon: 11.1 lbs/gallon Colors: 1703 Red 1704 Gray Solids by Weight: 60.1%+-1 -0% Application Information: Surface Preparation: Remove all oil, grease, dirt, loose or scaling paint, rust, mill scale and other contaminants. Thinner: W&W 2306 Brush or Roller W&W 2307 Spray Coverage: Brush or Roll--375-400 sq.ft. per gallon --200-225 sq.ft. per gallon Spray Film Thickness: Wet: 5.0 mils Dry: 2.0 mils Flash Point: 44F Setaflash Primers & Finishes: Compatible primers should always be used for specified surfaces. Two finish coats are usually recommended over primed surfaces to achieve desired mil thickness protection. Ferrous Metal: 1 coat --PRIME LINE Universal Primer 1703/1704 1 or 2 coats --WILBUR & WILLIAMS Alkyd Enamel --TUF-QUIK Oil Modified Urethane --TOTRUST Instant Dry Alkyd Enamel --TILE-COTE Polyamide Epoxy Enamel --TUF-ON Aliphatic Polyurethane --RUBBER-COAT Chlorinated Rubber Industrial Enamel --TUF-FLEX Water-Base Epoxy Enamel --RUST-STOP Acrylic Latex Metal Coating


79

CALIFORNIA PRODUCTS CORP.: WILBUR & WILLIAMS PRIME LINE 1705 Heavy Duty Metal Primer: Generic Type: Alkyd Phenolic Lead Silico Chromate Primer Exposure: Interior & Exterior Description: PRIME LINE #1705 is a single package heavy duty metal primer which is formulated with zinc chromate and lead silico-chromate pigments for maximum corrosion inhibition. It is intended for industrial use only by professionally trained personnel. PRIMELINE #1705 is a premium quality, corrosion inhibiting lead primer for ferrous metal, to be used in severe environments. An excellent primer for exterior and interior surfaces subjected to humidity and condensation including marine and coastal environments. Recommended Uses: Recommended for more severe exposure in and around refineries, industrial plants, and bridges. PRIME-LINE 1705 should be used where maximum protection is required. It may also be used as a "tie-coat'' over sound existing coatings before application of corrosion resistant systems. This material is compatible with most high performance coatings, including Polyamide Epoxy, Aliphatic Urethane, Chlorinated Rubber, Alkyd, Oil Modified Urethane, Acrylic and Vinyl Chloride systems. Appearance: Flat 15+-5 @ 60 Specular Gloss Solids by Volune: 41 .a%+-1 % Weight per Gallon: 11.5 lbs/gallon Color: Orange Solids by Weight: 73.4%+-1% Maximum VOC Content: 450 grams per liter. Application Information: Surface Preparation: Remove all oil, grease, dirt, loose or scaling paint, rust, mill scale and other contaminants. Thinner: Brush or Roll W&W 2306 Spray W&W 2314 Coverage: Brush or Roll--375-400 sq.ft. per gallon Spray --200-225 sq.ft. per gallon Flash Point: 80F Seta Flash Film Thickness: Wet: 3.5-4 mils per coat Dry: 1.5-2 mils per coat Primers & Finishes: Compatible primers should always be used for specified surfaces. Two finish coats are usually recommended over primed surfaces to achieve desired mil thickness protection. Ferrous Metal: 1 coat--PRIME LINE Heavy Duty Primer 1705 1 or 2 coats--WILBUR & WILLIAMS Alkyd Enamel TUF-QUIK Oil Modified Urethane TOTRUST Instant Dry Alkyd Enamel RUBBER COAT Chlorinated Rubber Industrial Enamel TILE-COTE Polyamide Epoxy Enamel TUF-ON Aliphatic Polyurethane

80

Prepaint Specialtiesand Surface Tolerant Coatings

CALIFORNIA PRODUCTS CORP.: Metal Primer:

WILBUR & WILLIAMS PRIME LINE 1706

Generic Type: Zinc Chromate Metal Primer Exposure: Interior or Exterior Description: An all purpose rust inhibiting metal primer that provides excellent protection to unfinished ferrous metal to be top coated with alkyd, urethane or latex finishes. Zinc Chromate Metal Primer has excellent adhesion and compatibility to clean aluminum surfaces, weathered galvanized metal surfaces and tin plate. The easy brushability and sanding qualities of this primer, and its compatibility with most top coats, make it ideal for spot touch up of previously primed metals. Recommended Uses: Can be used successfully on miscellaneous iron, rails and piping, construction equipment, weathered galvanized metal, aluminum windows and casework, or for spot touching other abraided metal primers. Appearance: Flat lo+-2 @ 60 Specular Gloss Solids by Volume: 46.0% Weight per Gallon: 11.3 lbs per gallon Acceptances: Meets performance specifiction for TT-P-645-Alkyd Type Color: Yellow Green Solids by Weight: 68.7% Application Information: Surface Preparation: Remove all oil, grease, dirt, loose or scaling paint, rust, millscale and other foreign matter. Thinner: Mineral Spirits Film Thickness: Wet: 3.5 mils/Dry: 2.0 mils Flash Point: 103 F Setaflash Primers & Finishes: Ferrous Metal, Aluminum, Weathered Galvanized Metal, and Tin Plate: 1 coat - PRIME-LINE Zinc Chromate Priemr 1706 1 or 2 coats - WILBUR & WILLIAMS Alkyd Enamel or TUF-QUIK Oil Modified Urethane Enamel or RUST-STOP Acrylic Latex Metal Paint. Previously Painted Metal Surfaces: Spot touch bare metal with: 1 coat PRIME-LINE Zinc Chromate Primer 1706 1 or 2 coats - WILBUR & WILLIAMS Alkyd Enamel or TUF-QUIK Oil Modified Urethane Enamel or RUST-STOP Acrylic Latex Metal Paint

-


81

CALIFORNIA PRODUCTS CORP.: WILBUR EL WILLIAMS Red Shop Primer 5512 Red Oxide Metal Primer: Generic Type: Long Oil Alkyd/Red Oxide Primer Exposure: Interior & Exterior Description: Red shop primer is an economical, air dry rust inhibiting primer formulated for cost effective applications. It is ideal for application on ferrous metal surfaces which are to be topcoated quickly. Recommended Use: Primer for structural steel, tanks, frames, equipment and miscellaneous iron. Red shop primer may be topcoated with conventional alkyds, oil modified urethanes or acrylic latex metal paints. Appearance: Eggshell finish 15+-5 @ 60 Specular Gloss Solids by Volume: 41 .lo% Weight per Gallon: 10.37 lbs. per gallon Color: Red Solids by Weight: 64.05% Application Information: Surface Preparation: Surfaces must be clean, dry and free of dirt, grease, mill scale, loose paint and other contaminants. Ferrous Metal: Commercial Blast Cleaned (SSPC-SPC) if at all possible. Minimum surface preparation would include Power Tool Cleaning (SSPC-SP3) or Handtool Cleaning (SSPC-SP2). Thinner: Spray Application--W&W 2301 Brush or Roller Application--W&W 2305 Coverage: Brush or Roll--300-400 sq. ft. per gallon Spray --150-250 sq. ft. per gallon Film Thickness: Wet 2.5-3.0 mils Dry: 1.5 mils Primers & Finishes: Recommended primers should always be used for specified surfaces. Two finish coats are usually recommended over primed surfaces to achieve desired film thickness. Ferrous Metal: 1 Coat--Red Shop Primer 1 or 2 Coats--WILBUR & WILLIAMS Alkyd Enamels TUF-QUIK Oil Modified Urethane Enamels RUST-STOP Acrylic Metal Paint

82 Prepaint Specialties and Svrface Tolerant Coatings

CALIFORNIA PRODUCTS CORP.: WILBUR 1056 Urethane Emulsion:

&

WILLIAMS RUST NEUTRALIZER

Generic Type: Water-Based Urethane Emulsion Exposure: Interior & Exterior Description: A one-package water based urethane emulsion type chemical rust neutralizer which chemically converts tightly adhering rust into an inert paintable surface and prevents the development of new rust. Recommended Use: For use on dry or damp rusted ferrous metal surfaces where only minimum surface preparation is practical. Maximum ferrous metal protection, however, is always provided by recommended surface preparation and the use of rust-inhibiting primers. Appearance: 25+-5 @ 60 Specular Gloss Solids by Volume: 32.65% Solids by Weight: 35.87% Weight per Gallon: 8.75 lbs. Colors: Milky White Application Information: Surface Preparation: Remove loose rust, mill scale, and deteriorated coating by scraping or wire brushing. Oil, grease, dirt and chemical surface contaminants should be removed by commercial detergent washing or other suitable cleaning method, followed by a thorough fresh water rinse. Thinner: Water Coverage: Brush or Roll: 225 sq.ft. per gallon Airless Spray: 125 sq.ft. per gallon Film Thickness: Wet: 3.5-4.0 mils Dry: 1.5-2 mils Flash Point: Non-combustible Primers & Finishes: Ferrous Metal: 1 Coat --WILBUR & WILLIAMS #lo56 Rust Neutralizer 1 or 2 Coats--TUF-QUIK 1800 Urethane Enamel RUST-STOP Acrylic Enamel TILE COAT 1200 Polyamide Epoxy


CALIFORNIA PRODUCTS CO.: WILBUR Latex Metal Paint:

&

83

WILLIAMS RUST-STOP 1046

Generic Type: Acrylic Latex Exposure: Interior or Exterior Description: A rust inhibiting acrylic latex metal paint for use on ferrous metal, galvanized metal and other surfaces exposed to general industrial and atmospheric conditions. This product has good solvent and water resistance and excellent resistance to most alkalies, detergents and mild acids. This acrylic metal paint does not contain the flammable solvents contained in other rust inhibiting paints, has low odor and fast recoatability. RUST-STOP makes an excellent self-priming metal paint over clean ferrous metal or on ferrous metal with a sound rusty surface from which mill scale has been removed. Complies with current V.O.C. regulations. Recommended Uses: Ideal for painting both new and previously painted roof decks, metal paneling, corrugated metal siding, storage tank exteriors, miscellaneous iron, bar joists and structural steel. RUST-STOP also provides excellent adhesion to galvanized ductwork and enclosures and for adjacent surfaces of wood and concrete. Appearance: Semi Gloss Finish 30+-5 @ 60 Specular Gloss Solids by Volume: 37.7% Weight per Gallon: 10.45 lbs. Acceptances: U.S.D.A.-Accepted F.S.I.S. Colors: White, Black & Bronzetone Custom colors factory mixed Solids by Weight: 50.07% Maximum V.O.C.: 250 g/liter Fire Rating: Test Method ASTM E84-80 Class A - Type I Flame Spread 5/Fuel Contribution O / Smoke Density 0 Application Information: Surface Preparation: Remove all oil, grease, dirt, loose or scaling paint, rust, mill scale and other foreign matter. Thinner: Water Coverage: Brush or Roll: 400-450 sq.ft. per gallon Spray: 220-225 sq.ft. per gallon Film Thickness: Wet: 3.5 mils dry/Dry: 2.0 mils Flash Point: No flammable solvent Primers & Finishes: Ferrous Metal: 2 coats RUST-STOP Acrylic Latex Metal Galvanized Metal, Aluminum: 2 coats RUST-STOP Acrylic Latex Concrete, Wood or Masonry: 2 coats RUST-STOP Acrylic Latex Previously Painted Surfaces: 1 coat RUST-STOP Acrylic Latex

84


CALIFORNIA PRODUCTS CORP.: WILBUR h WILLIAMS RUST-STOP 1067 Red/ 1061 White Acrylic Latex Metal Primers: Generic Type: Alkyd Modified Acrylic Latex Exposure: Interior or Exterior Description: Quick drying rust inhibiting acrylic latex metal primers for use over new or sound rusty ferrous metal surfaces from which mill scale and surface contaminants have been fully removed. Excellent for use over galvanized metal, aluminum, wood, and masonry surfaces to be topcoated with latex, alkyd or oil modified urethane coatings. Recommended Uses: Can be used successfully for priming miscellaneous iron, bar joists, ductwork, piping, galvanized metal, doors, sash, windows or for spot touching other abraded metal primers. Appearance: Flat 10F+-3F @ 60 Specular Gloss Solids by Volume: 37.03% Red 37.35% White Weight per Gallon: 10.3 lbs Colors: 1067 Red 1061 White Solids by Weight: 49.10% Red 49.05% White Application Information: Surface Preparation: Remove all oil, grease, dirt, mill scale, loose or scaling paint and other foreign matter. Thinner: Water Coverage: Brush or Roll: 400-450 sq. ft. per gallon Spray: 200-225 sq. ft. per gallon Film Thickness: Wet: 3.5 mils Dry: 2.0 mils Flash Point: No flammable solvent Primers & Finishes: Ferrous Metal--Precleaned, Aluminum, Galvanized Metal, Wood or Masonry 1 coat - RUST-STOP Acrylic Latex Metal Primer 1 or 2 coats - WILBUR & WILLIAMS Alkyd Enamel or TUF-QUIK Oil Modified Urethane Enamel or RUST-STOP Acrylic Latex Metal Paint Previously Painted Surfaces: Spot touch bare metal with: 1 coat - RUST-STOP Acrylic Latex Metal Primer 1 or 2 coats - WILBUR & WILLIAMS Alkyd Enamel or TUF-QUIK Oil Modified Urethane Enamel or RUST-STOP Acrylic Latex Metal Paint Extremely rusty surfaces may require a second coat of RUST-STOP Primer


CALIFORNIA COATINGS CORP.: Bright Aluminum:

85

WILBUR & WILLIAMS TOTALUME 2605

Generic Type: Oleoresinous Leafing Aluminum Exposure: Interior & Exterior Description: TOTALUME is a single package aluminum coating which combines the outstanding features of three types of aluminum pigment into a single self-priming coating. TOTALUME provides durable and decorative service under sustained adverse climatic conditions. TOTALUME will withstand up to 500F intermittent heat. Recommended Use: For use on chain link fences, transmission towers, tank exteriors, roof decks and metal finishing. Use wherever a brilliant long lasting lustre is desired, either interior or exterior. Appearance: Chrome Aluminum 70 @ 60 Specular Gloss Solids by Volume: 44.0% Weight per Gallon: 8.2 lbs/gallon Colors: Bright Aluminum Solids by Weight: 53.0% Application Information: Surface Preparation: Remove all oil, grease, dirt, loose or scaling paint, rust, mill scale or other contaminants. Thinner: Brush or roller: RUVIAL #2306 Spray: RUVIAL #2307 Coverage: Brush or Roll: 350-400 sq.ft. per gallon Airless Spray: 225 sq.ft. per gallon Glove or Mitt: Chainlink fence: 700 sq.ft. per gallon Film Thickness: Wet: 3.5 to 4 mils per coat Dry: 1.5 to 2 mils per coat Flash Point: 44F Setaflash Primers & Finishes: Compatible primers should always be used for specified surfaces. Ferrous Metal: 1 coat --PRIME-LINE 1703 Universal Metal Primer or TOTRUST 1596 Zinc Chromate Metal Primer 1 or 2 coats--TOTALLIME Bright Aluminum Galvanized and Aluminum Metal: 1 coat --GRIP COAT 6906 Vinyl Wash Primer or RUST-STOP 1061 Acrylic Primer 1 or 2 coats--TOTALUME Bright Aluminum Previously Coated Surfaces: Spot prime bare areas with appropriate primer 1 or 2 coats--TOTALUME Bright Aluminum


CALIFORNIA PRODUCTS CORP.: Zinc Rich Primer:

WILBUR & WILLIAMS ZINC SHIELD 5700

Generic Type: Organic Zinc Primer Exposure: Interior & Exterior Description: A one-compoment organic zinc rich coating containing 94% by weight of metallic zinc powder in the dried film. ZINC SHIELD can be used as a finish; however, topcoating is recommended for maximum protection. Designed to provide ferrous metal with cathodic rust protection comparable to galvanizing. Recommended Uses: Excellent for field touch-up of damaged galvanized on welds, rivet heads and voids. ZINC SHIELD has excellent corrosion inhibition and should be applied to bare steel to galvanize the surface. Ideally suited for steel subjected to constant high humidity. Renews worn out galvanizing and repairs inorganic zinc rich coatings. May be topcoated with RUST STOP Acrylic Latex Metal Paint or TILE COTE Polyamide Catalyzed Epoxy. Appearance: Matte Finish 8+-3 @ 60 Specular Gloss Solids by Volume: 40%+-2% Weight per Gallon: 21.9 lbs. Color: Gray Solids by Weight: 80%+-2% Acceptances: U.S.D.A.: This product has been designated chemically acceptable as a coating for incidental food contact surfaces in official establishments operating under the U.S. Department of Agriculture Meat and Poultry Inspection Program by its Food Safety and Inspection Service. Meets Government Specification DOD-P-21035 Type I. Application Information: Surface Preparation: Bare metal surfaces must be clean and dry. Remove all oil, grease and other contaminates by solvent wash or phosphate cleaning. The final usage of the area in which the ferrous metal is to be placed determines the amount of metal preparation necessary. Thinner: Spray application RUVIAL Reducer WW2307 Coverage: Spray 200 sq.ft. per gallon Brush 350 sq.ft. per gallon Film Thickness: Wet: 7.5 mils Dry: 3.0 mils Flash Point: 80F Setaflash Primers & Finishes: One or two finish coats of the types recommended should be applied over ZINC SHIELD 5700 primer, two coats are preferred for maximum sustained protection.



87

SSPC Preparation Chart:

Surface Preparation of Ferrous Metal: The importance of adequate surface preparation cannot be over-emphasized. Most coating problems can be traced to inadequate surface preparation. Proper adhesion cannot be attained without adequate surface preparation. The following surface preparation recommendations are a brief synopsis of specifications developed by the Steel Structures Painting Council. SSPC-SP1 Solvent Cleaning: The removal of dirt, oil, grease, soil, salts and other contaminants by cleaning with solvents or commercial cleaners using one of several methods such as wiping, dipping, steam, vapor degreasing, alkaline cleaner, or acid etching. Solvent wiping may not remove all oil and grease. Therefore, if the coating being used is not oil and grease tolerant, steam cleaning should be the method of choice. Many solvents are hazardous. Follow the safety precautions recommended by the particular solvent being used. SSPC-SPl, Solvent cleaning is included in all other SSPC Surface Preparation Specifications. SSPC-SP2 Hand Tool Cleaning: Hand tools are recommended for the removal of loose rust, loose mill scale, and loose paint by hand chipping, scraping, sanding and wire brushing. Usually recommended for cleaning all areas prior to maintenance painting in mild environments. SSPC-SP3 Power Tool Cleaning: Removal of loose rust, loose mill scale, and loose paint to degree specified by power tool chipping, descaling, sanding, wire brushing, and grinding. SSPC-SP3 is not adequate surface preparation for severe environments. SSPC-SP5 White Metal Blast Cleaning: Complete removal of all visible rust, mill scale, paint, and foreign matter by blast cleaning by centrifugal wheels or air nozzle using sand, grit or shot. Usually specified for high performance coatings in aggressive environments (i.e. corrosive atmosphere or immersion service). SSPC-SPC Commercial Blast Cleaning: The removal of all visible rust, mill scale, paint and other foreign matter by blasting with air nozzle or centrifugal wheels. Staining from rust or mill scale shall be limited to no more than 33 percent of each square inch of surface area. Used where a high, but not perfect, degree of blast cleaning is required. Not recommended for immersion service.


CALIFORNIAPRODUCTS CORP.: SSPC Preparation Chart(Continued): Surface Preparation of Ferrous Metal(C0ntinued): SSPC-SP7 Brush-off Blast Cleaning: Blast cleaning of all except tightly adhering residues of mill scale, rust and coatings. Mill scale, rust and paint are considered adherent if they cannot be removed by lifting with a dull putty knife. Normally used when surface profile is to be enhanced before repainting. SSPC-SPB Pickling: The complete removal of all rust, mill scale and foreign matter by acid pickling, duplex pickling or electrolytic pickling. Pickling is an effective method for removing contaminants on structural members, beams and plates prior to fabrication. Pickling is impractical for field use. SSPC-SP10 Near-White Blast Cleaning: The removal of all visible dirt, rust, mill scale, paint and other foreign matter. At least 95% of each square inch of surface area must be equivalent to SSPC-SP5 White Metal Blast. Less costly than SSPC-SP5 and adequate for all but the most severe environments.

Carboline 89

CARBOLINE: CARBOLINE D3358 Single Component Water-Borne Acrylic Primer: A high performance, easy-to-apply, direct-to-metal acrylic primer which can tolerate a variety of topcoats. CARBOLINE D3358 has exceptional film strength and chemical resistance.

-

-

Low odor Excellent flexibility Early resistance to moisture Excellent corrosion protection Excellent resistance to flash rusting Easily applied by spray, brush or roller May be topcoated with a variety of topcoats Meets the most stringent VOC (Volatile Organic Content) regulations

Recommended Uses: As a primer for applications requiring a fast drying, VOC (Volatile Organic Content) compliant primer such as railcar, tank exteriors and structural steel. Can be used as a two or three coat all acrylic system with CARBOLINE D3359 topcoat. Not Recommended For: Immersion service. Temperature Resistance (Non-immersion): Continuous: 235F (112.7C) Non-Continuous: 400F (204.4C) Substrates: Apply over suitably prepared metal, concrete or other surfaces as recommended. Compatible Coatings: Normally topcoated with CARBOLINE D3359. May be topcoated with certain epoxies, vinyls and urethanes. Specification Data: Theoretical Solids Content: By Volume: 36%+-2% Volatile Organic Content:* Per Actual Calculated EPA Gallon Method 24 As supplied: lbs/gal 1.33 0.58 160 69 911 1.33 0.55 Thinned 5% with lbs/gal 160 65 Potable Water g/1 * May vary slightly with color. Recommended Dry Film Thickness Per Coat*: 3-4 mils (75-100 microns) * Additinal thickness may be required over rough surfaces for appearance. Dry film thickness in excess of 5 mils/coat is not recommended.


CARBOLINE: CARBOLINE 801 Two-Component, Cross-Linked Epoxy: CARBOLINE 801 is a self priming, high build, semi-gloss finish available in a wide variety of colors. Can be applied by spray, brush or roller over hand or power tool cleaned steel and is compatible with most existing coatings and tightly adhered rust. The cured film is tough and abrasion resistant and provides an easily cleanable, esthetic surface. Features include: Single coat corrosion protection. - Good weathering resistance. - Good flexibility and lower stress upon curing than most epoxy coatings. - Excellent tolerance of damp (not wet) substrates. Can be spray applied up to 8 mils dry in one coat. Has a higher flash point than most epoxy coatings over llOF, including recommended CARBOLINE Thinner). Meets the most stringent VOC (Volatile Organic Con ent ) regulations.

-

-

Recommended Uses: Recommended as a general, plant wide, maintenance coating for tanks, structural steel or miscellaneous equipment in industrial environments that include Chemical Processing, Pulp and Paper, Water and Waste Water Treatment and Power Generation among others. May be used as a single coat, shop applied system for new structural steel and equipment that will receive mild chemical exposures. Two coats of CARBOLINE 801 are recommended for use in more severe environments. Not Recommended For: Immersion service, splash and spillage of very strong solvents or concentrated acids. Temperature Resistance: Continuous: 200F (93C) Non-continuous: 250F ( 1 21 C) Substrates: Apply over suitably prepared metal, concrete, or other surfaces as recommended. Compatible Coatings: May be used over most generic types of coatings which are tightly adhering and properly prepared. Specification Data: Theoretical Solids Content of Mixed Material: By Volume: 76%+-2% Volatile Orgamic Content: As Supplied: 1.74 lbs./gal. Recommended Dry Film Thickness Per Coat: 4-6 mils (100-150 microns) for use in mild environments. 6-8 mils (150-200 microns) for use over light tight rust.

Carboline 91

CARBOLINE: CARBOMASTIC 1 5 LOW Odor: Generic Type: Two-component, high-build, modified aluminum epoxy mastic. General Properties: CARBOMASTIC 15 Low Odor is a self-priming, high-build coating with excellent adhesion to rusted steel and most aged paints. Features include: Proven field performance. - Excellent performance over minimal surface preparations. - Low odor. - Non-bronzing. - Excellent application characteristics. - Excellent film build on edges. - Compatible with most aged coatings. Single coat for most applications. - Meets the most stringent VOC (Volatile Organic Content) regulations.

-

-

Recommended Uses: Particularly recommended for maintenance painting of rusty steel or upgrading old coatings. Ideal for metal buildings, piping, process equipment, highway bridges and exposed structural steel. Only a single coat is required for most applications. Hand or power tool cleaning is often acceptable. CARBOMASTIC 15 Low Odor may also be used where hand tool cleaned steel is being coated for the first time. Not recommended for: Immersion service in acids, alkalies or solvents. Temperature Resistance: (non-immersion) Continuous: l8OF (82C) Non-continuous: 250F (121 C ) Substrates: Rusty steel, aged galvanized steel or others as recommended. Compatible Coatings: May be used over most generic types of coatings which are tightly adhering and properly prepared. Specification Data: Theoretical Solids Content of Mixed Material: By Volume: go%+-2% Volatile Organic Content: As supplied: 0.74 lbs./gal. ( 8 8 grams/liter) Recommended Dry Film Thickness per Coat: 5 mils (125 microns) minimum (Measured excluding the rust on steel substrate). For severe exposures including immersion, 7 mils (175 microns) minimum or 2 coats at 5 mils (125 microns) each is recommended. Dry film thickness in excess of 10 mils (250 microns) per coat is not recommended.


COATINGS/COMPOSITES: Conductive FIBREICRETE: 2033-2043-2143:

Electrically conductive floor surfacer and lining. Primary Uses: Low resistance, non-sparking safety overlay. Fuel, munitions, solvent, paint, other flammable storage areas. Major Industries Served: Drug and pharmaceutical, arsenals, munitions and explosives plants. Primary Resistance: Acids, alkalis, solvents, fuels and petroleum. Broad Range Resistance: Solvents, acids. Major Physical Features: ohm resistance range. Other conductStandard 2 5 , 0 0 0 - 1 , 0 0 0 , 0 0 0 ivity ranges are available. Non-sparking. High impact and abrasion resistance. Solids by Volume: 1 0 0 % . Recommended No. of Coats: One. Coverage Per Coat: 40 sq. ft. per gallon at 40 mils thickness. Thickness Per Coat: 4 0 mils typical, horizontal. Usual Primer: CONO/WELD 5 0 1 . Usual Topcoat: CONDUCTIVE GLAZE 2 0 1 , 2 0 2 , or 222. Mixing Method: Heavy duty drill with JIFFY mixing blade. Application Method(s): Steel trowel, usually followed by light rolling. Standard Packaging: Quart, gallon, 2 3 gallon and 5 gallon units. Standard Stock Colors: Black. Special colors may be available. Some products are not color stable. Shipping Weight: 1 4 lbs. per gallon. Storage Life: 6 months in unopened containers.

CoatingdComposites 93

COATINGS/COMPOSITES: CONO/GLAZE 286:

Acid resistant protective coating. Primary Uses, Areas: General purpose acid resistant coating for protection of concrete, steel and other substrates in severe chemical environments. Major Industries Served: Chemical processing, electronics, plating, most other process industries. Resin (Part B): Vinyl ester. Hardener (Part A): Catalyst. Part C Component: Accelerator. Primary Resistance: Oxidizing acids. Other high concentration mineral and organic acids. Broad Range Resistance: Fuels and petroleum, chlorinated and aromatic solvents, hot water. Major Physical Features: Stain resistant, color stable. Medium gloss. Strong odor during application and cure. Solids By Volume: 65%. Recommended No. of Coats: Two. One over FIBREICRETE 285 or FIBREICRETE 285TL. Coverage Per Coat: 225 sq. ft. per gallon at 7 mils wet film thickness. Thickness Per Coat: 5-8 mils, wft; 3-5 mils, dft. Usual Primer: CONOIWELD 504. Usual Topcoat: None. Mixing Method: Heavy-duty drill with JIFFY mixing blade. Application Method(s):

Roller, brush, airless spray.

Standard Color(s): Light and dark gray. Shipping Weight: 12 lbs. per gallon.



Sanitary, tile like, solventless coating Main Use: Interior wall coating for concrete, block, drywall, plaster and most other construction materials in processing--packaging-clean room areas. Features: Hard, glossy film, easy to decontaminate, color fast, no odor, resistant to hot cleaners and chemical condensates. Industries Served: Food Processing, Pharmaceutical and Electronics Plants. Coverage/Thickness, Per Coat: 130 square feet per gallon/lO-15 mils. Coats: Two over primed surfaces, one over FIBRE/CRETE. Solids by Volume: + 9 8 % . Primer: CONO/WELD 5010 for cementitious surfaces. PRETREATMENT 5120 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Airless spray, brush, roller. Pot Life ( @ 70F.):

45 minutes to

Cure Time (Tack Free

@

70F.):

8

14 hours.

to 12 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Colors: White and gray ( # 9 9 and #53). Standard Colors: All colors on the COATINGS/COMPOSITES color chart. Shipping Weight: 12 lbs. per gallon. Storage Life: One year in unopened containers.

Coatings/Composites 95


Chemical Resistant, Solventless Coating Main Use: Interior exterior concrete and steel surfaces ie. process area structural steel, pits, trenches and floors. Features: Hard, glossy film, easy to decontaminate, excellent resistance to alkalies, acids, hydrocarbon solvents, fats and vinegar. Industries Served: Food Processing, Pharmaceutical and Electronics Plants. Coverage/Thickness, Per Coat: 130 square feet per gallon/lO-15 mils. Coats: Two over primed surfaces, one over FIBRE/CRETE. Solids by Volume: +98%. Primer: CONO/WELD 5010 for cementitious surfaces. PRETREATMENT 5120 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Airless spray, brush, roller. Pot Life ( @ 70F): 4 5 minutes to Cure Time (Tack Free

@

70F.):

14 hours.

8 to 12 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Colors: Beige and gray (#99 and #53). Not color stable. Shipping Weight: 12 lbs. per gallon. Storage Life: One year in unopened containers.


COATINGS/COMPOSIWS: CONO/GLAZE 2070: Lining concrete and steel tanks, steel ducts, stacks ie. clarifiers Features : Abrasion resistant, glossy film, easy to decontaminate, excellent resistance to alkalies, acids, hydrocarbon solvents, and salt solutions. Industries Served: Electric Power, Waste Treatment, Mining, Chemicals. Coverage/Thickness, Per Coat: 130 square feet per gallon/l0-15 mils. Coats: Two over primed surfaces, one over FIBRE/CRETE. Solids by Volume: +98%. Primer: CONO/WELD 5010 for cementitious surfaces. PRETREATMENT 5120 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Airless spray, brush, roller. Pot Life (@70F): 45 minutes to Cure Time (Tack Free

@

70F.):

13 hours.

8 to 12 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Colors: Beige and gray ( # 9 9 and #53). Not color stable. Shipping Weight: 12 lbs. per gallon. Storage Life: One year in unopened containers.


COATINGS/COMPOSITES:

CONO/GLAZE 2220:

Heat and chemical resistant, solventless coating Main Use: Interior, exterior coating of concrete and steel surfaces around Process equipment, tanks, and sumps. Features : Extremely hard, glossy film, easy to decontaminate, excellent resistance to chlorinated solvents, hot fats, oils and concentrated acids. Industries Served: Chemical Processing, Foods Cooking/Frying Plants, Oil Recovery, Pharmaceutical and Plating Facilities. Coverage/Thickness, Per Coat: 130 square feet per gallon/lO-15 mils. Coats: Two over primed surfaces, one over FIBREICRETE. Solids by Volume: +98%. Primer: CONO/WELD 5010 for cementitious surfaces, PRETREATMENT 5120 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Airless spray, brush, roller. Pot Life ( @ 70F): 45 minutes to 1; hours. Cure Time (Tack Free

@

70F.):

8-12 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Colors: Beige and gray ( # 9 9 and #53). Not color stable. Shipping Weight: 12 lbs. per gallon. Storage Life: One year in unopened containers.



Topcoat for epoxy toppings Main Use: Low gloss topcoat for newly installed epoxy toppings, to enhance cleanability. Features: Good holdout of the film maximizes film uniformity. Hard, easily cleaned sealer with good chemical resistance. Industries Served: Food Processing, Pharmaceutical and Electronics Plants. Coverage/Thickness, Per Coat: 200 square feet per gallon/4-5 mils Coats: One or two depending on finish desired. Solids by Volume: 1 0 0 % . Primer: CONO/WELD 5010 for cementitious surfaces, PRETREATMENT 5120 for metallic or non-porous surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Squeegee, or trowel tight to the floor, followed by backroll. Pot Life ( @ 70F): 45 minutes to 1;

hours.

Cure Time (Tack Free @ 70F): 6 to 1 0 hours. Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Color: Clear. Standard Colors: Light and medium gray, and brick red. Shipping Weight: 1 2 lbs. per gallon.



Sanitary, tile like, architectural coating. Main Use: Interior/Exterior wall coating for concrete, block, drywall, plaster and most other construction materials in Public Areas Packaging-Clean Room-Cafeterias-Processing. Features: "White" white stabile, glossy film, easy to decontaminate, low odor, resistant to normal cleaners and chemical condensates. Industries Served: Food Processing, Pharmaceutical and Electronics Plants. Coverage/Thickness, Per Coat: 175 square feet per gallon/7-8 mils. Coats: Two over primed surfaces, one over FIBREICRETE. Volatile Organic Content: 1 8 0 gms per liter Primer: CONO/WELD 5 0 1 0 for cementitious surfaces, PRETREATMENT 5 1 2 0 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Airless spray, brush, roller. Pot Life

(@

70F): 6-8 hours

Cure Time (Tack Free @ 70F.):

3 to 5 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Stock Colors: White and gray (#99 and #53). Standard Colors: All colors on the Coatings/Composites color chart. Shipping Weight: 11 lbs. per gallon.


COATINGS/COMPOSITES: CONO/WELD 5013: Conductive primer for conductive topcoats. Use: Priming concrete, vinyl tile, other sheet goods, wood and plastics, prior to application of CONDUCTIVE FIBRE/CRETE or CONDUCTIVE CONO/GLAZE. Features : Easily applied film, sets very low electrical resistance for subsequent top coats, fills minor surface defects and minimizes air entrapment in the topcoats, and non-sparking. Conductivity Range: 25,000 to 1,000,000 Code 56.

ohms when tested in accordance with NFPA

Industries Served: Munitions, Chemical, Aerospace and Pharmaceutical Plants. Coverage/Thickness, Per Coat: 225 square feet per gallon/6 to 8 mils. Coats: One. Solids by Volume: +98%. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Method: Trowel then backroll. Pot Life ( @ 70F.):

45 minutes to

Cure Time (Tack Free

@

70F.):

I f hours.

8 to 1 2 hours.

Standard Packaging: Quart, gallon, 3 gallon and 5 gallon units. Standard Color: Black. Shipping Weight: 12 lbs. per gallon. Storage Life: Six months in unopened containers.

Coatings/Composites 70 1

COATINGS/COMPOSITES: FIBREICRETE MORTAR 121: Aggregate filled fibre-reinforced floor surfacer. Primary Uses, Areas: Protective surfacer for new and lightly eroded concrete. Traffic and production areas, particularly mezzanine decks and upper floors. Major Industries Served: Chemical, food, most industries. Part C Component: Pre-measured hard, angular aggregate. Part D Component: Pre-measured pigment. Primary Resistance: Water, alkalis. Broad Range Resistance: Fuels, petroleum, aromatic solvents. Major Physical Features: High abrasion and impact resistance. Resists cracking from vibration. Non-slip safety. Solids By Volume: 100% Recommended No. of Coats: One. Coverage Per Coat: 1 0 0 sq-ft. per unit at 1 / 8 " thickness. Thickness Per Coat: 1 /8" minimum. Usual Primer: CONOIWELD 5 0 1 . Usual Topcoat: None. Occasionally CONO/GLAZE 235. Mixing Method: Mix in 4-7 cu.ft. plaster mixer. Application Method(s): Screed box for fast spreading at 1 1 8 " minimum. Finish by light steel troweling and rolling. Standard Packaging: 100 sq. ft. units (at 1 / 8 " ) . Standard Color(s): Gray and red. Shipping Weight: 1 4 5 lbs. per unit. Storage Life: One year in unopened containers.

102 Prepaint *ecialties and Surface Tolerant Coatings

COATINGS/COMPOSITES: FIBRE/CRETE 122:

Aggregate filled fibre-reinforced floor surfacer. Primary Uses, Areas: Protective surfacer for new and lightly eroded old concrete. Traffic and production areas, particularly mezzanine decks and upper floors. Major Industries Served: Chemical, food, most industries. Part C Component: Pre-measured hard, angular aggregate. Primary Resistance: Brine, food fats and oils, sugar, food acids, organic acids. Broad Range Resistance: Mineral acids, alkalis, fuels and petroleum, chlorinated and aromatic solvents. Major Physical Features: High abrasion and impact resistance. Resists cracking from vibration. Non-slip safety. Solids By Volume: 100%. Recommended No. of Coats: One. Coverage Per Coat: 100 sq. ft. per unit at 1/8" thickness. Thickness Per Coat: 1 /8" minimum. Usual Primer: CONO/WELD 5 0 1 . Usual Topcoat: None. Occasionally CONO/GLAZE 231. Mixing Method: Mix in 4-7 cu. ft. plaster mixer. Application Method(s): Screed box for fast spreading at 1 / 8 " minimum. Finish by light steel troweling and rolling. Standard Packaging: 1 0 0 sq. ft. units (at 1 / 8 " ) . Standard Color(s): Gray and red. Shipping Weight: 1 4 5 lbs. per unit. Storage Life: One year in unopened containers.

CoatingdComposites

103

COATINGS/COMPOSITES: FIBREICRETE 210:

High build reinforced flexible coating. Primary Uses, Areas: For exterior protection of concrete, masonry, galvanized steel, wood and other substrates in all environments. Flexible, reinforced coating for interior walls and ceilings in food process areas. Major Industries Served: Food and other "wet" processing industries. All types industrial and commercial buildings. Resin (Part B): Epoxy/acrylic copolymer. Hardener (Part A): None. Part C Component: None. Primary Resistance: Impervious to water penetration, exterior weathering, freezethaw cycling, ultraviolet light. Broad Range Resistance: Good resistance to most dilute acids and alkalis, solvents, fuels, and petroleum. Major Physical Features: Tough, semi-permeable film, allows passing of moisture vapor while blocking water entry. Long term flexibility. Bridges cracks and other defects, resists cracking caused by structural movement Solids by Volume: 80%. Recommended No. of Coats: One. Coverage Per Coat: 45 sq. ft. per gallon at 35 mils wet film thickness. Thickness Per Coat: 25-50 mils, wft; 20-40 mils, dft. Usual Primer: FIBREIMENT LIQUID 124. Usual Topcoat: CONO/GLAZE 251 or HYPEX 303. Mixing Method: Stir until consistency is uniform. Application Method(s): Airless spray, trowel and roll, brush. Standard Color(s): White. Easily tinted, color matched for large orders. Shipping Weight: 13 lbs. per gallon.


COATINGS/COMPOSITES: FIBRE/CRETE 285: High build reinforced acid resistant coating. Primary Uses, Areas: Thick film reinforced skid resistant surfacing and protective coating for concrete floors, pads, curbed areas and other surfaces in severe chemical environments. Major Industries Served: Chemical processing, electronics, plating, most other process industries. Resin (Part B): Vinyl ester. Hardener (Part A): Catalyst. Part C Component: Accelerator. Primary Resistance: Oxidizing acids. Other high concentration mineral and organic acids. Broad Range Resistance: Fuels and petroleum, chlorinated and aromatic solvents, hot water. Major Physical Features: High film strength, impact resistance. Resists physical abuse, peeling and flaking. Stain resistant, color stable, heat resistant. Strong odor during application and cure. Solids By Volume: 85%. Recommended No. of Coats: One or two as required. Coverage Per Coat: 4 0 sq. ft. per gallon at 40 mils wet film thickness. Thickness Per Coat: 30 mils minimum. Usual Primer: CONO/WELD 5 0 4 . Usual Topcoat: CONO/GLAZE 206 if required. Mixing Method: Heavy-duty drill with JIFFY mixing blade. Application Method(z):

Steel trowel, brush, airless spray.

Standard Packaging: Quart, gallon, 2; gallon and 5 gallon units. Standard Color(s): Light and dark gray. Shipping Weight: 1 2 lbs. per gallon.

CoatingdComposites 105

COATINGS/COMPOSITES: FIBRE/CRETE 2030:

Two-component, high build, high strength, fiber-reinforced, chemical and abrasion resistant coating. Primary Uses: Protection of concrete, steel, wood, plaster, concrete block and other surfaces. Major Industries Served: Food processing, brewing and bottling, pharmaceutical, electronics. Primary Resistance: Water, most dilute food processing chemicals. Broad Range Resistance: Dilute acids and alkalis, food processing condensation, most cleaning compounds and disinfectants. Major Physical Features: High film strength. Resists physical abuse, peeling and flaking, withstands refrigerated service, regular hot water washdowns. Solids By Volume: 9 9 % . FIBRE/CRETE Tensile Strength: 2 1 0 0 psi. FIBRE/CRETE Flexural Strength: 5 1 0 0 psi. FIBREfCRETE Elongation: 3.2% Recommended No. of Coats: One or more as required. Coverage Per Coat: 40 sq. ft. per gallon at 4 0 mils thickness. Thickness Per Coat: 4 0 mils typical. Usual Primer: CONO/WELD 501 (concrete), CONO/PRIME 5 0 6 (steel). Usual Topcoat: FIBRE/CRETE 203 or CONO/GLAZE 2 0 1 . Mixing Method: Slow speed, heavy-duty drill motor with JIFFY mixing blade. Application Method(s): Airless spray, trowel, brush. Standard Stock Colors: White and grey. Storage Life: One year in unopened containers.

106


COATINGS/COMPOSITES: FIBRE/CRETE

2040:

Two-component, high build, high strength, fiber-reinforced, chemical and abrasion resistant coating. Primary Uses: Protection of concrete, steel, wood, plaster, concrete block and other surfaces. Major Industries Served: Petrochemical, all types of chemical processing, fossil fuel power plants, mining, plating, oil recovery, electronics, aerospace, pharmaceutical, and most other industries. Primary Resistance: Dilute organic acids. Broad Range Resistance: Dilute mineral acids, brine, fuels and petroleum, chlorinated and aromatic solvents. Major Physical Features: High film strength. Resists physical abuse, peeling and flaking, will withstand hot or cold. Solids by Volume: 99%. FIBRE/CRETE Tensile Strength: 2100 psi. FIBRE/CRETE Flexural Strength: 5 1 0 0 psi. FIBRE/CRETE Elongation: 3.2% Recommended No. of Coats: One or more as required. Coverage Per Coat: 4 0 sq. ft. per gallon at 40 mils thickness. Thickness Per Coat: 40 mils typical. Usual Primer: CONO/WELD 501 (concrete), CONO/PRIME 506 (steel). Usual Topcoat: FIBRE/CRETE 203 or CONO/GLAZE 202. Mixing Method: Slow speed, heavy-duty drill motor with JIFFY mixing blade. Application Method(s): Airless spray, trowel and roll, brush. Standard Stock Colors: Beige and grey (not color stable). Storage Life: One year in unopened containers.


COATINGS/COMPOSITES:

FIBREVCRETE2060:

Two-component, high build, high strength, fiber-reinforced, dilute chemical and heavy abrasion resistant coating. Primary Uses: Thick film reinforced protective coating for steel, concrete and other surfaces subject to abrasion combined with chemical exposure. For coating material handling and storage equipment, hoppers, troughs, ducts, fans, pumps, other wet and dry service impingement or abrasive contact surfaces. Major Industries Served: Fossil fuel and hydroelectric power plants, mining and refining, chemical processing, waste treatment, and other processing industries. Primary Resistance: Fuels and petroleum, aromatic solvents, organic acids. Broad Range Resistance: Alkalis, chlorinated solvents, mineral acids. Major Physical Features: Very high abrasion resistance. High film strength. Resists physical abuse, wet or dry abrasion and impingement, peeling and flaking. Solids By Volume: 99%. FIBREICRETE Tensile Strength: 2500 psi. FIBREICRETE Flexural Strength: 4000 psi. FIBREICRETE Elongation: 3.1% Recommended No. of Coats: One or more as required. Coverage Per Coat: 4 5 sq. ft. per gallon at 35 mils thickness. Thickness Per Coat: 40 mils typical. Usual Primer: CONO/WELD 501 (concrete), CONO/PRIME 506 (steel). Usual Topcoat: FIBREICRETE 206 or CONO/GLAZE 207. Application Method(s): Airless spray, trowel, brush. Standard Stock Colors: Beige and grey (not color stable).


COATINGS/COMPOSITBS: FIBREICRETE 2140:

Two-component, high build, high strength, fiber-reinforced, moderate to harsh chemical and abrasion resistant coating. Primary Uses: Protection of concrete, steel, wood, plaster, concrete block and other surfaces. Major Industries Served: Petrochemical, all types of chemical processing, fossil fuel power plants, mining, plating, oil recovery, electronics, aerospace, pharmaceutical, and most other industries. Primary Resistance: Fuels and petroleum, chlorinated and aromatic solvents, sour crude, dilute nitric acid, high strength sulfuric acid. Broad Range Resistance: Organic and mineral acids. Major Physical Features: High film strength. Resists physical abuse, peeling and flaking. Excellent heat resistance. Solids by Volume: 99%. FIBREICRETE Tensile Strength: 4 1 0 0 psi. FIBREICRETE Flexural: 6000 psi. FIBREICRETE Elongation: 3 . 2 % Recommended No. of Coats: One or more as required. Coverage Per Coat: 4 0 sq. ft. per gallon at 4 0 mils thickness. Thickness Per Coat: 4 0 mils typical. Usual Primer: CONO/WELD 501 (concrete), CONO/PRIME 506 (steel). Usual Topcoat: FIBREICRETE 2 1 4 or CONO/GLAZE 2 2 2 . Mixing Method: Slow speed, heavy-duty drill motor with JIFFY mixing blade. Application Method(s): Airless spray, trowel, and brush. Standard Stock Colors: Beige and grey (not color stable). Storage Life: One year in unopened containers.

Coatings/Composites

109

COATINGS/COMPOSITES: FIBREIMENT 124: Steel fibre-reinforced modified cement mortar. Primary Uses, Areas: Reinforced underlayment for pitching floors to provide drainage. For rebuilding severly eroded concrete, curbs, trenches, sumps, pump bases and pads. Major Industries Served: Chemical, food, most process industries. Resin (Part B): Polyacrylic emulsion. Hardener (Part A): None. Part C Component: Selected hard, angular aggregate. A l s o separately packaged steel fibre-reinforcement. Portland low alkali cement, one bag per unit, purchased locally. Primary Resistance: N/A. Used as an underlayment. Broad Range Resistance: Overall chemical resistance exceeds that of concrete. Major Physical Features: Continuously steel reinforced for high strength. Resistance to cracking, impact, flexural movement, thermal shock, vibration. 5,000 psi compressive strength. Solids by Volume: 97%. Recommended No. of Coats: One. Coverage Per Coat: 4 0 sq. ft. per unit at 1 " thickness. Thickness Per Coat: 5 / 8 " minimum. Usual Primer: FIBRE/MENT LIQUID 1 2 4 . Usual Topcoat: CONO/WELD 501 primer followed by CONO/CRETE or FIBRE/CRETE-CONO/GLAZE products. Mixing Method: Mix in 4-7 cu. ft. plaster mixer. Application Method(s): Screed to correct grade. Finish by light troweling with magnesium or wood floats. Use plastic wrapped forms if required. Standard Packaging: 3 . 4 cu. ft. units. Standard Color(s):

Natural, cement color.

Storage Life: One year in unopened containers, above freezing.

110


COATINGS/COMPOSITES: HYGRIP 1630, 1640, 1660: Skid resistant, fibre reinforced, epoxy coating. Main Use: Provide non-skid surfacing to concrete ramps, stairs, walkways, and in wet or greasy areas. Features : Thick reinforced coatings that can't peel or flake, secures hard angular aggregate & provides resistance to a broad range of chemicals. Coverage/Thickness, Per Coat: 40 square feet per gallon/4O mils. Coats: One Solids by Volume: +99%. Primer: CONO/WELD 5010 for cementitious surfaces, PRETREATMENT 5120 or CONO/PRIME 5060 for metallic surfaces. Mixing Method: Heavy-duty power drill with JIFFY mixing blade. Application Methods: Trowel, roller. Pot Life ( @ 70F.):

45 minutes to

14 hours.

Cure Time (Tack Free @ 70F): 8 to 12 hours. Standard Packaging: Quart, gallon, 24 gallon and 5 gallon units. Stock Colors: Gray (#53). Standard Colors: 1630--All colors on the Coatings/Composites color chart. 1640 & 1660--Gray and red (#53 and #63) Not color stable. Shipping Weight: 19 lbs. per gallon. Storage Life: One year in unopened containers.

Coatings/Composites

COATINGS/COMPOSITES: PRETREATMENT 512: Adhesion promoter for low porosity surfaces. Primary Uses, Areas: A "wash primer" type surface conditioner for ferrous and non-ferrous metals, dense concrete, glazed tile, fired brick, and similar substrates. Promotes adhesion for tank linings, ducts, chimneys, scrubbers, and other wet process or temperature cycling dynamic environments. Major Industries Served: Electric power, chemical processing, mining and refining, most other industries. Resin (Part B): Proprietary--dispersed in a mixture of non-flammable chlorinated solvents. Hardener (Part A): None. Part C Component: None. Major Physical Features: By Elcometer testing, proven to increase adhesive strength of direct applications onto steel by 2 0 - 4 0 % . Often eliminates the need for a primer. Fast evaporation with strong solvent odor. Will not suppress flash rusting. Solids by Volume: Approximately 4 % . Recommended No. of Coats: One, applied thin and uniformly as possible. Coverage Per Coat: 600 sq.ft. per gallon at 2 . 7 mils wet film thickness. Thickness Per Coat: 14-3 mils wet film thickness. Cannot be measured due to immediate wetting and evaporation. Usual Primer: N/A Usual Topcoat: Epoxy resin based primers, linings or coatings. Mixing Method: Hand stir prior to use. Application Method(s): Hand pumped sprayer, roller, brush. Standard Color(s):

N/A. Water-clear liquid.

11 1

1 12 Prepaint Specialties and Surface Tolerant Coatings

COMPOSITION MATERIALS CO., INC.:

PLASTI-GRIT:

Government approved custom engineered dry stripping abrasive for fast, safe, low-cost surface cleaning and. paint removal. PLASTI-GRIT types and applications: Type 1: Polyester 3 Moh Hardness 34-42 Barcol Hardness Selected applications: Paint, primer and contamination stripping of soft metals and fiberglass. Light deburring and deflashing of enscapulated electronic components. Type 2: Urea 3 . 5 Moh Hardness 54-62 Barcol Hardness Selected applications: Significantly more aggressive than Type 1 . For stripping aircraft, trucks, trailers, tractors, rail cars, vans, motor homes, marine vessels, cars, buses. Type 3: Melamine 4 Moh Hardness 6 4 - 7 2 Barcol Hardness Selected applications: Difficult-to-remove paints and primers from hard materials, i.e. engine parts, turbine blades. CLEAR-CUT: 20-30 Barcol Hardness PLASTI-GRIT CLEAR-CUT, a thermoset plastic, is the most recent addition to Composition Materials' family of PLASTI-GRIT dry stripping abrasives. Its extraordinary cutting capabilities particularly recommend it as a paint remover and surface cleaner for composites and soft metals. With this excellent cutting action at the recommended low pressures of 20-25 psi, CLEAR-CUT preserves the surface profile of even the most delicate composites and soft metals as well as the geometry of thin metal panels

.

PLASTI-GRIT approved by the U.S. Government Composition Materials Co., Inc., developers of PLASTI-GRIT dry stripping media, was awarded GSA Contract #GS07F15581 for its PLASTI-GRIT product. The Government's recommendation of PLASTI-GRIT for military bases and private companies is based on its effective stripping capabilities and its positive impact on the problems of air pollution, toxic waste and health hazards.

Crest Industrial Chemicals

CREST INDUSTRIAL CHEMICALS, INC.:

Products:

ACID CLEANER #I: Heavy Duty Oxidation Remover

Metal Conditioner

&

113

ACID CLEANER #1 is an effective and economical compound especially formulated for use in the aircraft industry. It is used as a prepainted treatment to provide a slightly porous surface which will absorb primer, providing a firm base for paint. It is also used to remove surface oxidation from aluminum aircraft surfaces and aircraft parts. ACID CLEANER #I is also excellent for cleaning and restoring valve bodies. It will remove rust and some paint leaving a light phosphate coating

.

Method of Use: ACID CLEANER #1 is applied by brushing, swabbing, spraying or immersion. PCC-6 Aluminum Conversion Coating: Immersion or spray washing process for providing aluminum with a golden iridescent chemical film or coating of the surface conversion type, for protection against corrosion and improvement of paint adhesion. Applicable Specification: PCC-6 meets the requirements of MILC-5541C. Pre-Cleaning: Before immersion in the PCC-6 bath, surfaces to be treated must be free from grease and other surface soils. Deoxidizing: With certain alloys, it may be advisable to employ a deoxidizing treatment of some kind prior to the conversion bath. PCC-11: Colorless Aluminum Conversion Coating Immersion or spray washing process for providing aluminum with a clear chemical film or coating of the surface conversion type, for protection against corrosion and improvement of paint adhesion. Applicable Specification: PCC-11 meets the requirements of MIL-(2-5541 C Pre-Cleaning: Before immersion in the PCC-11 bath, surfaces to be treated must be free from grease and other surface soils.

1 14



Products(Continued):

PPC-66: Low Temperature Liquid Iron Phosphating Compound PPC-66 is a liquid compound specifically formulated to process iron and steel at low temperatures where a smooth tight crystalline coating is required. It may be used in a three or five stage spray washing system to provide improved paint adhesion and corrosion protection. Properties: Color and Odor: Clear, water white, odorless liquid free from any sediment. Storage Stability: Under normal storage conditions (32-120F) the product will not change in color or physical state or suffer loss in effectiveness for a period of at least one year. GALV-A-PAINT: Metal Conditioner for Galvanized

&

Zinc Metal

CREST GALV-A-PAINT is a liquid metal conditioner used to treat galvanized & zinc metal, by hand wiping or immersion applications. GALV-A-PAINT reacts chemically with the surface of these metals and allows paint to adhere smoothly and evenly. In addition, once paint has dried GALV-A-PAINT helps prevent it from chipping or peeling. Properties: Color and Odor--Light blue liquid, free from any sediment with no objectional odor during use and leaves no residual odor. Color Control--When GALV-A-PAINT is applied to the metal surface a dark tint develops. Uncovered areas are easily visible. This makes sure that the entire surface can be visually inspected for complete coverage. Storage--GALV-A-PAINT will not change in physical state or suffer loss in effectiveness for a period of one year when storage conditions are maintained between 32 degrees F. and 1 4 0 degrees F. Application Methods: CREST GALV-A-PAINT may be applied by hand or tank immersion.

Crest Industrial Chemicals


115

Products(Continued):

PPC 97: Manganese Phosphate A dip phosphate for iron and steel where heavy coatings are required. Purpose: Used as coatings on the frictional surfaces of gears, bearings, crankshafts, valve lifters, tool joints, etc. to prevent galling, scuffing and scoring during break-in periods. A PPC-97 coating is particularly suitable for impregnation with oils, or other lubricants for increased corrosion and friction resistance. PPC-97 (ManganeseINickle Phosphate) exceeds coating weight and corrosion resistance as called out in Military Specification MIL-P-16323F. Surface preparation of the metal before phosphating is one of the most important factors in obtaining a quality coating. Cleaning: Surfaces may be cleaned by abrasive blasting or chemicals. PPC-98 : Zinc Phosphate A dip phosphate for iron and steel Purpose: Used as coating on the frictional surfaces of gears, bearings, crankshafts, valve lifters, tool joints, etc., to prevent galling, scuffing and scoring during break-in periods. A PPC-98 coating is particularly suitable for impregnation with oils, or other lubricants for increased corrosion and friction resistance. Surface preparation of the metal before phosphating is one of the most important factors in obtaining a quality coating. Cleaning: Surfaces may be cleaned by abrasive blasting or chemicals. A rough metal surface often accelerated the coating formation producing fine crystalline coatings. Very fine coatings are obtained on gritblasted, sand-blasted, and vapor-blasted surfaces. Machined areas, on the other hand, may produce nonuniform, shiny coatings.


CROWN INDUSTRIAL PRODUCTS CO., INC.: Spray Paints & Coatings:

CROWN Industrial Aerosol

Top Quality Spray Paints# for Industrial Use! Crown's Maintenance & Touch Up Paint adheres where other paints fail, with special ability to cling to metals and other hard-to-cover surfaces. Crown's M & T Paints are specially formulated and give outstanding coverage for a given amount of paint used. Fast dry formula has a high percent of solids. # All Crown Paints are Alkyd Enamels..unless

-

-

indicated.

Corrosion Resistant Superior Coverage No Fading Fast Drying

Maintenance & Touch-up Paints (OSHA Colors) Fluorescent Paints Hi-Temperature Paints Stencil Inks Other Coatings Use For: Maintenance--Machinery, plant and office furniture, painted duct work, piping, etc. Production--Small parts painting, production line touch up. Sales--Display equipment, models. Shipping--Stenciling for export or domestic shipments, final touch up. OSHA standards for safety color coding: Green: Green shall be used as the basic color for designating "Safety" and the location of first aid equipment other than firefighting equipment. Red: Red shall be the basic color for the identification of fire protection equipment and apparatus, danger, and stop. Yellow: Yellow shall be the basic color for designating caution and for marking physical hazards. Orange: Orange shall be used as the basic color for designating dangerous parts of machines or energized equipment which may shock or cause injury. Black & White: Black, white or a combination of these two, shall be the basic colors for the designation of traffic and housekeeping markings. Purple: Purple shall be the basic color for designating radiation hazards. Yellow should be used in combination with purple for markers such as tags, labels, signs, and floor markers.

Crown Industrial Products CO.

CROWN INDUSTRIAL PRODUCTS CO.,

INC.:

117

DURA-PRIME Non-Chromate

Primer: An Excellent Primer...For

All Metals!

DURA-PRIME is a powerful rust preventative primer for indoor or outdoor use on iron and steel. Rust inhibiting pigments give it unsurpassed durability. Provides a tough bond with outstanding adhesion characteristics...an excellent general purpose primer for use on all metals. Forms an excellent base for finish paint The answer to field touch-up of machinery and equipment Resilient...Elastic...Resists abrasion, moisture and chemical fumes. DURA-PRIME...Dries tack free in 1 0 minutes under normal conditions. May be top coated with or without sanding after curing for 12 hours. DURA-PRIME...has many uses in Manufacturing Industries, Processing Plants, Transportation Industry, Aviation Industry, Power and Public Utilities, Marine..anywhere a good quality primer is needed. Technical Data: Color: Green or Yellow Pigment: 9.6% Solids Boiling Point: 173-1 78F. Non-Volatile % Vehicle: Phenolic 1.6 Alkyd Type Resins - 6.7 Flash Point: Open Cup: 22F. Closed Cup: 20F. Spray Rate: ( 1 gram/sec.) Coating Excellent Vapor Pressure (at 21C.): Aerosol 45 P.S.I.G. Cm Hg 308 Toxicity: None When Used as Directed Specific Gravity: 1 .lo-1.15 Dry Time: Tack Free - 10 Minutes Dry - 12 Hours (Before Use)

-

118 Prepaint $k?cialties and Surface Tolerant Coatings

CROWN INDUSTRIAL PRODUCTS CO., INC.:

KLEER KOTE:

Clear Acrylic Plastic with no equal in Rust Prevention and Waterproofing! KLEER KOTE sprays on clear and stays clear. It adheres to all metals, wood, paper, and provides a tough film that protects against wear, handling, and oxidation. Resists heat, cold, salts, alkalies, mold acids...will not crack or peel...prevents bleaching or fading from sunlight as well as corrosion and tarnishing. Benefits : Water-clear transparency; resistance to discoloration even at high temperatures. - Outstanding durability. - Excellent resistance to mineral oil, vegetable oils, and greases. - Outstanding resistance to chemical fumes. - Excellent flexibility. - Good electrical properties. - Relatively high resistance to burning. - Excellent outdoor durability. - Excellent adhesion.

-

General Properties: CROWN KLEER KOTE dries by evaporation at approximately 1 Mil thickness with average ventilation at room temperature, between 10-20 minutes. With temperature at 350F., KLEER KOTE becomes tacky, but upon cooling it regains its hardness without loss of original properties. Baking at 250F. for 30 minutes improves hardness, mar resistance and other properties. Film Properties: Baked, 30 minutes at 250F. Tukon Hardness: 8.7 Knife Adhesion: Excellent Flexibility: (1 /8" Mandrel) Good Electrical Properties: Dielectric Strength ASTM Test Method D149 1346 (Short-time) !!./Mil. Volume Resistivity Ohm-CM: 9 x 1 0 13 ASTM Test Method D257 Surface Resistivity OHM-Sq.: 2 X 10 1 4 ASTM Test Method D257

DAP

DAP Inc.:

119

DERUSM Rust Preventive Enamel with Built-In Primer:

Semi-Gloss, Metallic, Gloss

&

Flat Finishes:

Superior quality, rust preventive alkyd enamel provides heavy-duty protection to metal, wood and masonry. DERUSTITE anti-rust primer is built-in, for one coat rust prevention. May be applied to rusted areas where extra protection is required. Superior resistance to salt, weather moisture, mild chemicals, fumes, grease and abrasion. Excellent primer or finish coat. Recommended for storage tanks, steel sash, structural steel, conveyors, fork lifts, piping, machinery, hoists, tractors, trucks and general maintenance. V.O.C. compliant formulas are available.

-

Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss Gloss

Red Orange Light Yellow Yellow Golden Yellow Light Green Green Medium Green Ivory Almond Beige Brown Light Blue Blue

-

-

-

Gloss Dark Blue Gloss School Bus Yellow Flat White Gloss Light Gray Gloss Gray Gloss Airways Orange Flat Black Semi-Gloss Black Semi-Gloss White Semi-Gloss Gray Semi-Gloss Dark Red Semi-Gloss Dark Green Metallic Aluminum

Implement and Machinery Colors With built-in primer. Heavy-duty corrosion resistant protection for painting and touch-up of farm machinery and industrial equipment.

-

John Deere Green International Red Caterpillar Yellow Ford Blue Allis-Chalmers Orange

Oil Field Colors With built-in primer. Durable, rust preventive enamel for heavy equipment, oil rigs, metal framework and machinery. Resists chipping, peeling and fading. Emsco Green Black - Caterpillar Yellow - Unit Rig Gray - Waukesha Gray - New National Blue - Bethlehem Yellow - Oil Well Orange - Dark Emsco Green - Aluminum - White

-

-

120


DAP INC.: DERUSTO Rust Preventive Enamel with Built-In Primer (Continued): OSHAIANSI Safety Finishes: RED--Identification of fire equipment and apparatus. Identification for Nonionizing Radiation YELLOW--Color designing caution and marking physical hazards; identification for Ionizing Radiation, X-Ray, Alpha, Beta, Gamma, Neutron, Proton Radiation ORANGE--Designating dangerous machine parts--WARNING PURPLE--Biological Hazard or Biohazard; identification for Ionizing Radiation BLACK--Identification for Nonionizing Radiation, X-Ray, Alpha, Beta, Gamma, Neutron, Proton Radiation BLACK & WHITE--Identification for traffic areas & housekeeping purposes GREEN--Identification for safety Basic Color identification of pipes (ASA scheme for identification of pipes) RED--ASA CLASS F--Fire Protection equipment and sprinkler piping BLUE--ASA CLASS P--Protective materials YELLOW or ORANGE--ASA CLASS D--dangerous materials GREEN--ASA CLASS S--Safe materials

-

-

OSHA OSHA OSHA OSHA

Safety Safety Safety Safety

White Black Green Orange

-

OSHA OSHA OSHA OSHA

Safety Safety Safety Safety

Blue Yellow Red Purple

GALV-A-GRIP: Specially formulated, ready-to-use one-part modified alkyd enamel for galvanized metal, aluminum, tin, stainless steel and other smooth metal surfaces. Grips tight when ordinary paints fail. Resists cracking, checking and peeling. Use as a primer or finish coat for gutters, downspouts, roofs, flashings, piping, ducts, fences and machinery. Complies with California V.O.C. regulations.

-

White Grey Black

-

Red Green

Moisture Resistant Finish (MO-501): High-gloss, one-part modified alkyd system. Withstands high moisture conditions found in dairies, breweries, food processing plants, waste water plants and laundries. Cleans easily. Resists mold, mildew, abrasion and yellowing. White

-

DAP

121

DAP INC.: DERUSTO Rust Preventive Enamel with Built-In Primer (Continued): C-GLO Fluorescent Enamels: Highly visible, modified alkyd enamel. Provides a brilliant, reflective finish that captures immediate attention, day or night. Many industrial surveying or aviation applications. Use for safety signs and hazards, directional markings, alarm boxes, lift trucks, helmets and piping.

-

Red Orange

-

Yellow Green

Epoxy Hi-Gloss Enamel: Smooth, glossy finish stands up to scrubbing, abrasion and impacts when applied to metal, masonry or wood. Resists mold, mildew, yellowing, grease and detergents. Provides tough protection for major appliances, outdoor furniture, office furnishings and machinery.

-

White Black Copper Brown Copper Brown Shadow

-

-

Avocado Harvest Gold Shadow Harvest Gold Almond

High Temperature Enamels: Heat resistant, modified silicone resin system. Withstands high temperatures without cracking, bubbling or peeling. Provides long-lasting protection to metal, brick and masonry without priming. Excellent for boilers, ovens, incinerators, stacks, furnaces, radiators and pipes. Formulas available to comply with V.O.C. regulations.

-

Barbecue & Stove Black 1300F HEAT MASTER Copper Brown 800F HEAT MASTER Aluminum 800F HEAT MASTER White 600F Paint will withstand heat up to temperatures indicated

Clear Protective Acrylic: Fast drying, transparent finish seals out air, moisture, salt and other corrosive elements. Helps prevent tarnishing and pitting of metal surfaces.

-

Clear


DAP INC.: DERUSTO Rust Preventive Enamel with Built-In Primer (Continued): EASE-IT Silicone Spray: Silicone-based spray minimizes friction, eliminates squeaks, preserves and lubricates. Leaves no greasy film.

-

Clear

TOPS Roof Coating: Heavy-duty roof coating for industrial, commercial, farm and residential buildings. Waterproofs, preserves and protects felt, primed steel, aluminum or asphalt roofs. White: Latex-Based Aluminum: Asphalt-Based Rust Preventive Primers: Extra-tough, penetrating alkyd enamel primer defends against air and moisture. Grips tightly to bare, rusted or painted surfaces. Ideal for wood, metal, and masonry. Excellent primer for high moisture and industrial applications. Interior/Exterior.

-

Flat Black Primer Flat Gray Primer Flat Red Primer

MINUTE-SOLV Thinner: Excellent quality, general purpose thinner for spraying, dipping, and specialized brushing or rolling applications. Easily cleans fresh paint from brushes, rollers and spray guns.

-

Clear

DAP

DAP INC.:

123

High Temperature Enamels:

DERUSTO and BROMA High Temperature Enamels are one-part, modified silicone resin coatings for use where a heat resistant finish is essential. This durable, heat-cured system dries to a reflective aluminum finish that resists extreme temperatures without cracking, bubbling or peeling. Designed to provide long-lasting protection to bare, painted or firmly rusted ferrous metal surfaces without priming. Resists air and moisture, salt, grease, oil, gasoline, fumes and abrasion. Protects against rust and corrosion. DERUSTO Barbeque Black and HEAT MASTER Enamels: Heat resistant enamels renew and protect grills, stoves, fireplaces, heaters, boilers. Withstand high temperatures without cracking, bubbling or peeling. Prevent rust. Maintain a long-lasting finish on metal, brick, masonry and similar surfaces. Barbeque Black resists heat up to 1300F. HEAT MASTER Aluminum resists heat up to 800F, White to 600F and Copper Brown to 800F. BROMA Heatmaster (400F): Aluminum finish for surfaces exposed to temperatures up to 400F. Ready mixed. Dries quickly. Use on boilers, steam generators, steam pipes and other industral equipment.

124 Prepaint s;Oecialties and Surface Tolerant Coatings

JAMES B. DAY

&

CO.:

DACONITE Industrial Finishes:

KUT-KOTE Liquid Paint and Varnish Remover: Designed as the perfect all around economy remover, outstanding in its field, KUT-KOTE Liquid Remover is a powerful combination of cutting solvents that will "knife" thru hard paint, lacquers, shellac and varnish coatings. Stays wet and put. Flammable and requires rinsing with mineral spirits or turpentine before refinishing.

NO-FLAME Paint and Varnish Remover: NO-FLAME is the most powerful type of remover known. It will efficiently and quickly remove all types of finishes with a lifting or "popping" action in the film that is much easier to take off the surface than with the conventional types of removers. No usual clean-up rinsing with NO-FLAME. Meets with the rigid standards of Fire Department requirements and can be safely used where other removers cannot. DACONITE Semi-Paste Alkyd Wood Filler: A filler formulated to meet the requirements of all modern type finishes. The semi-paste consistency saves time in reducing to working consistency. Ready for finishing in 4 to 8 hours. E-27943 Natural E-27944 Walnut

DIP STRIP Dipping Remover: A chlorinated solvent type remover formulated similar to NO-FLAME Remover. The principal difference is that DIP-STRIP contains no thickening agent and requires complete immersion of the article or area to be stripped. DIP-STRIP is safe and will not support flames by itself. However, if subjected to extremely high temperatures, it gives off toxic fumes, so exposure to flame or high heat should be avoided. Tank should be covered as much as possible to prevent excessive evaporation.

James B. Day & Co.

JAMBS B. DAY

&

CO.:

125

DAYCO Products:

Removers : MARINE STRIP Heavy Duty Remover: Guaranteed flameproof and explosion proof. Especially formulated for the heavy duty requirements of marine, automotive and aircraft maintenance. NO-FLAME Paint & Varnish Remover: Water rinsable - meets the rigid standards of Fire Department requirements. Will remove all types of finishes with a lifting action that is easier to take off the surface than with conventional removers. Liquid KUT-KOTE Remover: A perfect all around remover to meet the volume popular priced demand. Flammable, it requires a neutralizing rinse before refinishing. Won't raise the grain of the wood. DAYCO Liquid Brush Cleaner--New Improved--Now Water Rinsable: An excellent cleaner for softening and dissolving hard paint, varnish, lacquer or shellac from bristle or nylon brushes. Completely disintegrates all the traces of paint material, leaving the bristle lustrous and pliable. DAYCO SCUFF--Surface Preparation--Deglosser: A clear solvent composition designed to eliminate application problems when painting over old glossy varnishes or enameled surfaces. Deglosses old film and prepares the surface for better adhesion of subsequent finishes. Removes dirt, grease, wax or polishes. Eliminates crawling of new finish. To improve bond of oil base primers and undercoats, add up to 4-ounces SCUFF per gallon on first coat only. Excellent for cleaning scuff marks or dirt from new wood surfaces. Unsurpassed as a brush or roller cleaner. Miscellaneous: PRESTO SEAL (New Improved First Coater): Guaranteed the whitest, best hiding sealer for use under all types of oil or water base paints and enamels. Gives positive protection against all bleeding problems. Odor freedries in I-hour.

126 Prepaint *ecialties and Surface Tolerant Coatings

JAMES B. DAY EL CO.:

DAYCO Products(C0ntinued):

Miscellaneous(Continued): DASOL Alcohol Solvent: For cutting shellac, spirit enamels, stain sealers and cleaning equipment used in the application of these products. Used also as a fuel for spirit lamps, torches, chafing dishes, etc. For cleaning presses, typewriters and as a degreaser for metal parts. DAYCO Semi-paste Wood Filler(A1kyd): Natural E-27944 Walnut E-27943 A filler formulated to meet the requirements of all modern type finishes. The semi-paste consistency saves time in reducing to working consistency. Ready for finishing in 4 to 0 hours. LEM-0-OIL Polish: A populer type polish for home, commercial or industrial use. Produces a brilliant gloss on varnish, lacquers, or enameled surface. Cleans as it polishes and leaves no greasy residue. DACOTHANE Sanding Sealer (Clear Polyurethane Sealer): A stearate-free sanding sealer designed principally for use under companion product, DACOTHANE, or other polyurethane finishes. Prepared surfaces must be clean, dry and free from wax and grease. Refinished surfaces should be cleaned with alcohol or mineral spirits to insure a thorough clean-up after stripping. DACOTHANE SANDING SEALER is not recommended over products containing stearates so where staining and filling is desired, check all labels and follow manufacturers' directions carefully. COVERSOL (Heavy Duty Flat White Primer-Sealer): COVERSOL offers excellent hiding qualities and provides an ideal, quick coater for priming and sealing bare or previously painted surfaces as wood, plaster, drywall, hardboard, etc. Unsurpassed for its stain-killing and sealing qualities COVERSOL effectively seals in charred surfaces of "fire-jobs", smoke stains, odor, and the most difficult water stains. COVERSOL dries quickly; normally 45 minutes, and may be recoated in approximately one hour. Recoating may be with any interior or exterior latex, oil, alkyd flats, enamels or house paints. COVERSOL may be tinted, if desired, with universal colorants.

Detrex Gorp.

DETREX CORP.:

Product Data:

Product Group: Immersion cleaners-ferrous: DETREX EC-600: Heavy duty DETREX 75: Extra heavy duty, hard water cleaner DETREX 75-LQ: Liquid, alkaline cleaner and rust remover DETREX 75-RLZ: Heavy duty soak cleaner, liquid DETREX EC-375D: Heavy duty, low temperature liquid cleaner

Spray cleaners-ferrous: DETREX EC-30: Powdered, heavy duty, low temperature cleaner DETREX 37: Medium duty cleaner, in-plant protection DETREX EC-375: Liquid, heavy duty low temperature cleaner

Immersion cleaners-non-ferrous: DETREX 74: High surfactant cleaner for aluminum and copper DETREX AE: Etchant for aluminum DETREX EC-376-D: Heavy duty low temperature liquid aluminum cleaner

Spray cleaners-non-ferrous: DETREX EC-31: Medium duty, powdered, low temperature cleaner DETREX EC-376: Heavy duty, liquid, low temperature cleaner

127


DETREX CORP.:

Product Data(Continued1:

Pre-soak cleaners: DETREX 30-56: Liquid detergent immersion cleaner for the removal of buffing compounds Electrolytic cleaners: DETREX 53: Cleaner for brass and copper DETREX 77: Heavy duty cleaner for iron and steel DETREX CRP, EK and FR: Steel mill electrolytic cleaners Emulsion cleaners; DETREX EC 4 1 9 8 and DETREX 1198: Single phase and biphase emulsion cleaners with in-plant rust protection Activated paintbond cleaners: DETREX 700 Series: Mildly alkaline cleaning compound for use in spray washers prior to zinc phospating to refine crystalline structure Paint Strippers: DETREX BCA: Alkaline paint stripper, good for stripping paint booths DETREX 537-K: Liquid alkaline paint stripper Spray booth coatings: DETREX VINCOTE: DETREX PR Series: Used on spray booth to facilitate the accumulation of paint over-spray Deflocculants: DETREX Booth-Trol Series: Unique group of polymer products designed to condition paint in water-wash spray booths.

Detrex Corp.

DETREX CORP.:

Product Data(Continued):

Neutralizers: DETREX CN and CX: Used after pickle, free rinsing Miscellaneous specialties: DETREX B: General maintenance cleaner DETREX GF: Alkaline cleaner for terrazzo and concrete floors DETREX 40 Series: Liquid floor cleaner for manual use or with automatic equipment DETREX M Series: Alkaline rust remover for immersion tanks DETREX 79-A: Special non-fogging or etching product for cleaning glass DETREX 78: Concentrated non-ionic surfactant system DETREX Rinse Aid: Concentrated liquid used in final rinse stage of cleaning DETREX CR-660: Liquid, neutral rust remover for ferrous and non-ferrous metals Acidulated rinses Non-chrome rinses: DETREX REXOLENE Series: Liquid concentrate used as final treatment on phosphate coatings for paintbonding and rustproofing purposes Immersion iron phosphate: DETREX FE-729: Powdered iron phosphate to produce corrosion resistant paintbond iron phosphate coating on iron and steel

129


DETREX CORP.:

Product Data(C0ntinued):

Immersion zinc phosphates: DETREX MICROBOND 603: Fine grain coating for steel, excellent for paint where high gloss is required DETREX 16-HC: For steel, used prior to paint and/or rubber bonding DETREX 1020 CN: Heavy coating for steel, phosphate and oil process DETREX 821 : Wipe-on zinc phosphate for iron and steel and zinc plated surfaces DETREX 1048 Series: Micro crystalline zinc phosphate for pre-paint, rubber bond Spray zinc phosphate: DETREX MICROBOND 707 Series: Fine grain coating for automobile and truck body lines Zinc paintbond accelerators: DETREX 702-B: Liquid material to accelerate coating rate of zinc phosphate material Spray calcium phosphate: DETREX MICROBOND 747: Fine grain coating for the appliance industry Spray powdered iron phosphates: DETREX 900 Series: Used to produce a corrosion resistant paintbonding iron phosphate on iron and steel DETREX EC-900 Series: Low temperature, used to produce corrosion resistant paintbonding iron phosphate on iron and steel DETREX PAINTBOND 7EC: Used to produce a corrosion resistant paintbonding iron phosphate on iron, steel, aluminum and galvanized surfaces

Detrex Corp.

DETREX CORP.:

131


Spray liquid iron phosphates: DETREX 920: Used to produce a corrosion resistant paintbonding iron phosphate on iron and steel using a 5 or more stage washer DETREX 922-A: Designed for use in steam gun equipment to produce paintbond coatings DETREX 940WL: Liquid low temperature iron phosphate that produces excellent coating on steel and iron surfaces Rustproofing immersion phosphate coatings: DETREX 1020 Series: Used to produce a corrosion resistant zinc phosphate coating on iron and steel on fasteners, automotive hood hinges, springs, etc. DETREX PERM-COTE CB: Predip to produce jet black protective and decorative coating on fasteners, hood hinges, springs, etc. DETREX PERM-COTE MN-I : Manganese phosphate used on iron and steel normally for break-in purposes. Rustproofing oil: DETREX PERM-OIL: Rust preventive for use on zinc phosphate coatings, good in hard water areas. Water soluble Acid Detergents: DETREX 800 Series: Used to remove soils and light rust from iron and steel DETREX 841 -S: Used to clean-out spray washers and tanks to remove scale and sludge build-up


DETREX CORP.:


Aluminum conversion coatings: DETREX AR-6P/AR-7P: DETREX AR 6 7 : Single compound, low temperature liquid system to produce an amorphous chromate phosphate coating on aluminum and aluminum alloy extrusions DETREX 400 Series: Produces an amorphous chromate coating on aluminum and aluminum alloys at low temperature in batch operations DETREX AM-1 / A R - 2 : Liquid system to produce an amorphous chromate coating on aluminum strip for continuous strip lines Extrusion phosphates: DETREX EXTRUDICOTE CM-1 and CR-R: Phosphate coating prior to wire drawing DETREX EXTRUDICOTE CR-1: Prior to cold forming of steel using various types of lubricants DETREX EXTRUDICOTE F, S, and 11 Series: Oxalate coatings for stainless and exotic alloys for extrusion and tube drawing operations Rolling Oils: DETREX Rolling Oil NB I T Series: Multistand DCR cold reduction f o r tin plate and TFS stock DETREX Rolling Oil: Tandem mill reduction of cold roll light and heavy gauge sheet product Drawing Compounds Synthetics:

CROWN DRAW 5061: A total synthetic for zinc coated steels that will handle severe as well as moderate draws

CROWN DRAW 5035WP: A versatile synthetic for cold roll and is used for deep draws CROWN DRAW M-14: A n economical and versatile synthetic soap for ferrous and non-ferrous

Detrex Corp.

DETREX CORP.:

133


Corrosion rust preventives: CP-4200: A series of synthetic and water extendable products that provide varying degrees of short term rust protection on ferrous and non-ferrous metals CP-6000: A series of solvent and oil based rust preventives for longer, more severe corrosion requirements, from six (6) months outdoor to several years indoor Corrosion Package: XRP-26: A highly concentrated additive package which produces corrosion protection in coolant systems and extends the life of the systems Specialty Metal Cleaners: WAYCLEAN 221, R-514-A, 516, 518, 521, 536, 570 and 537: Alkaline cleaners for specialty metalworking operations on aluminum, cast iron and press equipment Emulsion Base Cleaners and Corrosion Inhibitors: C-2, C-15, C-15-GA, C-28-T, C-40, C-64, 1103-C and 7-6-T Emulsion Broad base line of emulsifiable oil and oil based additives for cleaning and corrosion protection of mild steel and cast iron parts Solvent Based Corrosion Inhibitors: #6, 7, 10, 20, and DF-2 PROTEX and #20 SURFASEAL: Solvent based corrosion inhibitors which deposit corrosion inhibitors as the solvent is evaporated Oil Based Corrosion Inhibitors: A-35, 638 PROTEX #ll-WM and #ll-WM additive package: These products are oils and oil soluble corrosion inhibitors. They leave a thick film on treated parts


DETREX CORP.:


PrimerslMetal: Dip/Spray/Flo-Coat/Waterborne/Solvent Coating of component automotive parts, as well as various sheet metal application Applicable for general industrial, as well as meeting Government Specifications Primers/Plastics: a) Thermosets b) Rim c ) Thermoplastics Conductive/Non-conductive/Hi-solidlurethane Priming of automotive body panels and decorative trim parts Applications Engine Enamel: Solvent/Hi-solid/Waterborne Engine enamels engineered to meet automotive and general industrial specifications Chassis Blacks: Dip/Spray/Flo-coat/Solvent/Waterborne Coating for chassis, shocks, struts, brake drums, and various black-out applications. High performance corrosion protection Striping Lacquers and Enamels: Decorative vehicle striping for all major automotive manufacturers Material Handling Coatings: Spray/Waterborne/Solvent/Hi-solids Primers and finish coats for material handling industry Miscellaneous Specialty Coating: Fluorescents/Urethane/Sealers/Rust-Preventive/Resist Coating High performance and decorative coating for general industrial and automotive application

Devoe Coatings Co.

DEVOE COATINGS CO.:

BAR-RUST

235 Multi-Purpose EPOXY Coating:

Features: Exceptional Corrosion Resistance - Salt and fresh water immersion resistance - Corrosive chemical environments Lowers the Cost of Surface Preparation Grit blasting is not a requirement Excellent adhesion to tight rust Good adhesion to damp surfaces Low Temperature Cure - Cures down to OF (-18C) Recoats in 3 hours at 70F (21C) Application: Self-priming Approvals EPA and AWWA-potable water - Lloyd's-grain cargo - DOD-P-23236A(SH)-for ballast tanks

-

-

Recommended Uses: Tank Linings and Pipe Coatings - Ballast and potable water tanks - Bilges, wet voids and drainage pipes Ships, Offshore and Marine Structures - Above and below-water hull areas Decks and superstructures - Multi-purpose repair coating Structural Steel, Equipment and Masonry Surfaces - Pulp and paper mills Chemical and fertilizer plants Sewage treatment plants Storage tanks and pipes - Bridges Fabrication and New Construction Speed up production, even at low temperatures - A single multi-purpose, surface-tolerant coating

-

-

-

Specification Data: Coating Type: Advanced technology epoxy Colors: Buff Haze Gray Oxide Red Component Ratio: 4 to 1 by volume Gloss: Semi-gloss Flash Point: 100F (38C) Setaflash Pot Life: 5 hours at 77F (25C) Induction Time: 15 minutes Shelf Life: More than 2 years Density: 10 Lbs/Gal (1.2kg/l) VOC (average): 2.4 Lbs/Gal (287 Grams per liter) Temperature Resistance: 250F (121C) dry Volume Solids: 65% Application: Spray, brush or roller

135


DEVOE COATINGS CO.:

BAR-RUST 236 Multi-Purpose Epoxy Coating:

Features: LOW voc: 1.41 Lbs/Gal (170 Grams per liter) Outstanding Corrosion Resistance Suitable for fresh and salt water immersion Corrosive environments Resistant to many solvents and chemicals Resistant to cathodic disbondment Lowers Cost of Surface Preparation Grit blasting not a requirement - Good adhesion to tight rust Good adhesion to damp surfaces Low Temperature Cure-Fast Recoat Cures down to OF (-18C) Recoat in 3 hours at 70F (21C) Application: Self priming High solids, 5-8 mils per coat - Flash point over lOOF (38C)

-

Recommended Uses: BAR-RUST 236 is a true universal coating Tank Lining: - Ballast tanks, water tanks, bilges and any other water containment structures - Cargo, chemical, fuel and solvent resistant Ships, Offshore and Marine Structures Above and below water hulls, decks and superstructures, internal tanks, voids and wet spaces--ideal maintenance coating Structural Steel, Equipment and Masonry Surfaces Pulp and paper mills, chemical and fertilizer plants, sewage treatment plants, tank farms, piping and bridges Fabrication and New Construction Speeds up production; fast recoat and cure even a low temperatures Multi-purpose, surface tolerant coating

-

-

Specification Data: Coating Type: Advanced technology epoxy Color: Buff Medium Gray Oxide Red Component Ratio: 4 to 1 by volume Flash Point: lOlF (38C) Setaflash Pot Life: 4 hours at 77F (25C) Induction Time: 15 minutes at 77F (25C) Density: 12.7 Lbs/Gal (1.5 kg/l) VOC: 1.41 Lbs/Gal (170 Grams per liter) Temperature Resistance: 250F (1 21 C) dry Volume Solids: 80%

Devoe Coatings Go.

DEWlE COATINGS CO.:

137

PRE-PRIME167 Rust Penetrating Sealer:

Features: Reinforces Rusty Steel Substrates Penetrates Through Rusty Surfaces - Cures to a Tough, Water Resistant Coating 100% Volume Solids Very low viscosity Low film thickness required No shrinkage

-

-

Recommended Uses: The extraordinary penetrating properties of PRE-PRIME 167 sealer provides a means of reinforcing rusty steel substratesthis in turn insures the adhesion of subsequent coatings. Recommended in areas where, due to restrictions or economics? blasting or thorough hand cleaning is not feasible Very effective sealer and/or reinforcement for masonry surfaces. - Excellent sealer for aged "white rusted" zinc surfaces

-

Specification Data: Coating Type: 100% Solids epoxy Color: Clear Component Ratio: 3 to 1 by volume Gloss: Medium sheen Flash Point: lOOF (38C) Setaflash Thinner: Do not thin Pot Life: 4 hours at 77F (25C) Shelf Life: More than 1 year Density: 8.5 Lbs/Gal (1.02 kg/l) voc: 0 Temperature Resistance: 250F (121C) dry Volume Solids: 100% Theoretical Spreading Rate: 1604 Sq Ft/Gal at 1 mil 39.3 Sq. m/l at 25 microns Recommended Film Thickness: 1.5 wet mils to obtain 1.5 dry mils Application Methods: Air spray? brush or roller Dry Time: At 77F (25C), 50% RH To recoat: Overnight

138 Prepaint s;Oecialtiesand Surface Tolerant Coatings

DOLPHIN PAINT & CHEMICAL CO.:

DOLCHEM 6010/6011/6015:

Air Dry Body Sealants: Alkyd, air dry body sealants with excellent adhesion to fiberglass, bare, primed and painted metal, and to vinyl. DOLCHEM 6010 is widely used for repairing plastisol sealed joints and seams in auto and truck body assembly; and it is also used as the sole interior and exterior sealant on customized vehicles, such as limousines. DOLCHEM 6010 and 6011 are identical except for color. Both can be painted over after a skin is formed and will not discolor most lacquers and enamels. These sealers will withstand paint bakes after the solvent in the sealer has evaporated. Application: These products may be applied with a flow gun, caulking gun, knife or brush; if spray application is desired, use DOLCHEM 6015. DOLCHEM 6010 and DOLCHEM 6011 are available in standard caulking cartridges, ones, pails, and drums. These sealants skin over in approximately five minutes; dry time may be shortened by force drying. These sealants may be painted as soon as they are set to touch. Clean equipment with toluene or xylene. Properties: Specific Gravity: 1.46-1.50 Color: DOLCHEM 6010 = White DOLCHEM 6011 = Black DOLCHEM 6015 = White Sprayable Solids: 76-78% Flash Point: 95F (35C) DOLCHEM 6010 & 6011: Viscosity, Brookfield: 300,000-400,000 cps @ 2 RPM Viscosity, Press Flow: 5-15 seconds @ 60 psi 25-45 seconds @ 30 psi 200-300 poise Sag Resistance: No sag with .185" bead DOLCHEM 601 5 : Viscosity, Brookfield: 120,000-140,000 @ 2 RPM 70,000- 90,000 @ 20 RPM Viscosity, Press Flow: 10-20 seconds @ 40 psi 200-300 poise Dry Time @ 68F; 50% RH: 5 minutes set to touch 72 hours through dry

Dolphin Paint and Chemical Co.


139

DOLCHEM 6016:

Level Putty, White This high quality putty is used by level manufacturers to hold the lens in place over the bubble vial in precision levels built for the professional craftsman. This material will withstand severe impact, vibration, water immersion, and temperatures from near boiling to below freezing without cracking or losing adhesion. This putty offers excellent adhesion to glass, steel, aluminum, and wood without priming. DOLCHEM 6016 has excellent exterior durability by itself, but may be coated if necessary. Application: In level assembly, a special putty tool or a teaspoon is used to force the putty into the corner of the lens opening; the use of these tools gives the putty a very smooth surface. These putties can also be applied with a putty knife or molded by hand and used as a thumbing putty. Properties: Specific Gravity: 2.03-2.07 Color: White, color matched putties available upon special order Solids: 96% - 98% Flash Point: 130F Viscosity, Penetrometer: 16.0-18.0 nun


DOLPHIN PAINT & CHEMICAL CO., INC.:

DOLCHEM 6020 Series:

Elastomeric Sealants The DOLCHEM 6020 Series offers tough, thermoplastic rubber adhesivelsealers in a wide variety of colors, including custom color matches. These sealants bond to a wide variety of substrates; these include glass, fiberglass, steel, aluminum, rubber, and most primed and painted surfaces. The DOLCHEM 6020 Series of Elastomeric Sealants has found wide use in recreational vehicle and bus assembly in both interior and exterior applications. These products may be painted over, if necessary; paint adheres well to them and they do not discolor finishes. In service, these adhesive/sealers provide bond strengths as high as many "structural" adhesives with the ultimate in flexibility, even when exposed to extremely low temperatures. Properties: Specific Gravity: -88 .93 Color: 10 colors available & clear plus custom color matches DOLCHEM 6021 = Clear DOLCHEM 6022 = Aluminum DOLCHEM 6025 = Black DOLCHEM 6029 = White

-

DOLCHEM 6035/DOLCHEM 6036/DOLCHEM 6037/DOLCHEM 6038: Low Viscosity Elastomeric Adhesive/Sealants These adhesivelsealants are flowable versions of the DOLCHEM 6020 series. Their lower viscosity permits them to flow into seams and self level in drip rails and on roof joints. These tough, air dry, thermoplastic rubber adhesive/ sealants adhere to most surfaces; these include glass, fiberglass, steel, aluminum, rubber and most primed and painted surfaces. The DOLCHEM 6035 Series of Adhesive/ Sealants has found varied applications in the assembly of recreational vehicles with the DOLCHEM 6020 Series; their ease of application from pump oilers to small seams permits their use as trim sealant around windows and along corner and edge trim. They have excellent exterior durability; and, as they flow into seams, they supplement mechanical fasteners. These products may be painted over, if necessary; paint adheres well to these adhesive/sealants and they will not discolor most finishes. In service, These adhesive/ sealants provide bond strengths as high as many "structural" adhesives with the ultimate in flexibility, even when exposed to extremely low temperatures. Properties: Specific Gravity: .87--92 Color: 3 colors available and clear plus custom color matches Solids: 43-47%



14 1


Fast Dry Body Sealants The DOLCHEM 6060 Series offers fast drying, general purpose, rubber caulking compounds in a variety of colors, including custom color matches. These high solids sealants give the user the capability of filling large seams and holes because of their great resistance to slumping and their minimal shrinkage upon drying. When dried, these products provide a very flexible seal which will withstand vibration and flex through a wide range of service conditions. These sealants bond to most substrates; these include glass, fiberglass, steel, aluminum, rubber, and most primed and painted surfaces. The DOLCHEM 6060 Series of Fast Dry Body Sealants has found wide use in the transportation industry as both an interior and exterior sealer on autos, truck cabs and bodies, trailers, and buses. These products may be painted over, if necessary; most paints adhere well to these sealants; and normal industrial paint bakes will improve the physical properties of the cured sealants. Properties: Specific Gravity: 1.32-1.36 Color: 4 colors available plus custom color matches DOLCHEM 6030 = White DOLCHEM 6063 = Black Solids: 80% - 82% Flash Point: 45F Viscosity, Press Flow: 10-20seconds @ 60 psi 35-55 seconds @ 30 psi 300-700 poise Sag Resistance: No sag with .625" bead Dry Time @ 68F; 50% RH: 5 minutes set to touch 24 hours through dry The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Adhesion Peel: 20 lbslin from CRS 15 lbslin from Alum. Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealant Flammability: Pass Self extinguishing within 2"



DOLCHEM 6 0 6 5 :

Heat Resistant Sealant A general purpose, air dry, oleoresinous sealant formulated with a blend or marine and vegetable oils for corrosion protection and heat resistance. This material forms a tough outer skin, but remains elastic and pliable to withstand vibration and flexing. It is used for both electrical and general sealing of cold rolled, stainless and galvanized steel, aluminum, and wood assemblies. In service, this sealant is not affected by atmospheric conditions, no matter how extreme. The original heat resistant formulation was developed more than fifty years ago for use throughout passenger rail cars; heat resistance was needed because the sealant was used on undersides in areas exposed to high heats during operation. Since its development, this heat resistant sealant has found use as a sealant for the exterior walls of industrial ovens. The formula for the current DOLCHEM 6065 uses the same blend of oils that was used in 2055HR, but the current formula is asbestos free.

Properties: Specific Gravity: 1.32-1 -35 Color: Gray-Green Solids: 89-91% Flash Point: 103F Sag Characteristics: No sag with .625" bead The following tests were performed after drying 21 days (20C), 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance:'No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Less than 1 "/min.

@

68F



143

DOLCHEM 6066/DOLCHEM 6067:

Elastomeric Adhesive/Sealants These two, thermoplastic rubber, air dry compounds are used as both sealants and adhesives; these fast drying products bond tenaciously to steel, aluminum, glass, fiberglass, vinyl, rubber, and most primed and painted surfaces. These products are similar to plastisol body sealers in consistency and are used to repair skips and leaks in plastisol sealed bodies; they are used as adhesives to fasten weatherstripping and for bonding in windows. These materials resist water wash off after only 30 minutes ambient dry; they may be painted over as soon as the solvents have evaporated; as they fully cure at room temperature in 48 hours. The adhesion and strength improve if they are submitted to normal industrial paint bakes. These two products are identical except for color. Properties: Specific Gravity: 1.25-1.29 Color: DOLCHEM 6066 - Black DOLCHEM 6067 - White Solids: 77-79% Flash Point: 65F Viscosity, Brookfield: 250,000-350,000 cps @ 2 RPM 80rOOO-100,000 CpS @ 20 RPM Viscosity, Press Flow: 5-15 seconds @ 60 psi 20-40 seconds @ 30 psi 175-325 poise Sag Resistance: No sag with .185" bead Dry Time @ 68F; 50% RH: 10 minutes set to touch 4 8 hours through dry The following tests were performed after drying 21 days @ 68F; (20C) 50% RH: Adhesion, Peel: 20 lbs. from glass 25 lbs. from CRS Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Burn rate less than l"/min.

144


DOLPHIN PAINT & CHEMICAL CO.: DOLCHEM 6068/DOLCHEM 6069: Exterior Body Sealants These plasticized thermoplastic rubber body sealants offer properties similar to heat cured vinyl plastisol body sealers without a curing oven. These sealers air dry completely at ambient temperatures; after drying, they provide the same adhesion, flexibility, and durability of plastisol body sealers. These sealers can be "dressed" like a plastisol but set very quickly (they resist water wash off in 30 minutes); after drying, they can be painted over with most automotive, truck, and industrial enamels. If a finish requiring a bake is used, the heat used to cure the finish will improve the adhesion and stength of the sealers. These sealers bond to bare steel, phosphated steel, aluminum and most primers, including electrodeposition epoxy primers. Properties: Specific Gravity: 1.28-1 -32 Color: White Solids: 78-80% Flash Point: 106F DOLCHEM 6068: Viscosity, Press Flow: 5-15 seconds @ 60 psi 30-45 seconds @ 30 psi 150-500 poise Sag Resistance: No sag with .625" bead DOLCHEM 6069: Viscosity, Brookfield: 400,000-450,000 cps @ 2 RPM 9O,OOO-11O,OOO CPS @ 20 RPM Viscosity, Press Flow: 5-15 Seconds @ 60 psi 15-30 seconds @ 30 psi Sag Resistance: No sag with .25" bead Dry Time @ 68F; 50% RH: 45 minutes set to touch 48 hours through dry The following tests were performed after drying 21 days (20C); 50% RH: Hardness, Shore A Durometer: 55-65 Tensile Strength: 150 psi Elongation: 150% Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Burn rate less than l"/min

@

68F


DOLPHIN PAINT k CHEMICAL CO.: DOLCHEM 6072:

145

DOLCHEM 607O/DOLCHEM 60711

Anti-Corrosion Sealants These oleoresinous, air dry, lap joint sealants are unsurpassed in preventing corrosion including preventing galvanic corrosion between dissimilar metals. A thin skin forms on the exposed sealer through oxidation to permit painting while the non exposed sealer remains "wet", flexible, and elastic. In service, these sealers withstand vibration, flexing, and thermal expansion and contraction. These products are formulated to permit drilling through the sealer in riveted assemblies without "stringing" or "cobwebbing". Because they do remain wet internally, removing and replacing damaged panels is facilitated. These sealants are waterproof, acid and caustic resistant, and do not bleed into or through epoxy or urethane finishes; they are not affected by normal urethane topcoat bakes. Properties: Specific Gravity: 1.35-1 -38 Color: DOLCHEM 6070 - Yellow DOLCHEM 6071 - Black DOLCHEM 6072 Aluminum Solids: 88-92% Flash Point: 106F Viscosity, Press Flow: 15-35 seconds @ 60 psi 45-85 seconds @ 30 psi 500-1 000 poise Sag Resistance: No sag with .25" bead Dry Time @ 68F; 50% RH: 96 hours set to touch Does not dry through

-

The following tests were performed after drying 21 days (20C); 50% RH:

@

68F

Adhesion, Peel: 3 lbslin. from CRS 3 lbslin. from Aluminum Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No galvanic reaction between aluminum and steel Flammability: Pass Burn rate less than 2"/min.



DOLCHEM 6094:

Insulating Thumbing Putty This non-shrinking, oleoresinous putty is used for filling large voids, cracks and holes in wood and metal assemblies. The exposed surface forms a skin after application while the inside remains pliable. This putty is used in the assembly of truck cabs and busses because its permanent flexibility will withstand the vibration and torquing these vehicles must endure in service. This putty offers excellent flame and electrical resistance; and it was originally developed for military use to seal, insulate, ane waterproof electrical junction boxes. This putty may be painted over and will not bleed through most industrial enamels; it is unaffected by normal paint bakes. Properties: Specific Gravity: 1.61-1.64 Solids: 99% minimum Dry Time @ 68F; 50% RH: Non-drying DOLCHEM 6095: Thumbgrade Sealer A high solids, oleoresinous putty used for filling large voids, cracks, and holes in wood and metal assemblies. The exposed surface forms a tough skin, while the inside remains pliable. This putty may be painted over after skin has formed and will not bleed through most industrial enamels.

Properties: Specific Gravity: 1.585-1.610 Solids: 96%-98% by weight Flash Point: 65-70C (1 50-1 60F) Viscosity, Penetrometer: 16.0-17.5 nun Dry Time @ 68F; 50% RH: May be painted over in 2 hrs 7 Days for full strength The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Water Resistance: Less than 1% weight change Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Burn rate less than l"/min.



147

DOLCHEM 6096:

Aluminum Lap Joint Sealant A low viscosity, flowing, oleoresinous compound designed to stop water leaks in sealed and welded lap joints; its viscosity enables this sealant to flow into seams by capillary attraction. Once the sealant has dried, the path of the water leak is completely blocked. The compound has been formulated to prevent galvanic corrosion between dissimilar metals; it has found wide use between aluminum and stainless or cold rolled steel; it has been used on truck and rail car bodies as the sole sealer between aluminum rub rails and steel side panels. In service, DOLCHEM 6096 is water resistant, paintable, and will withstand temperatures up to 200F. Properties: Specific Gravity: 1.30-1.33 Color: Aluminum Solids: 71 -73% Flash Point: 103F Viscosity, Brookfield: 15,000-20,000 cps @ 2 RPM 5r000-10r000CpS @ 20 RPM Dry Time @ 25C; 50% RH: 3 hours set to touch 8 hours through dry The following tests were performed after drying 21 days (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Self extinguishing

@

68F



DOLCHEM 6010/601 /6015:

Air Dry Body Sealants: Alkyd, air dry body sealants with excellent adhesion to fiberglass, bare, primed and painted metal, and to vinyl. DOLCHEM 6010 is widely used for repairing plastisol sealed joints and seams in auto and truck body assembly; and it is also used as the sole interior and exterior sealant on customized vehicles, such as limousines. DOLCHEM 6010 and 6011 are identical except for color. Both can be painted over after a skin is formed and will not discolor most lacquers and enamels. These sealers will withstand paint bakes after the solvent in the sealant has evaporated. Application: These products may be applied with a flow gun, caulking gun, knife or brush; if spray application is desired, use DOLCHEM 6015. DOLCHEM 6010 and DOLCHEM 6011 are available in standard caulking cartridges, ones, pails, and drums. These sealants skin over in approximately five minutes; dry time may be shortened by force drying. These sealants may be painted as soon as they are set to touch. Clean equipment with toluene or xylene. Properties: Specific Gravity: Color: DOLCHEM 60 DOLCHEM 60 DOLCHEM 60 Solids: 76-78% Flash Point: 95F

1.46-1 -50 0 = White 1 = Black 5 = White Sprayable 35C)

DOLCHEM 6010 & 60 1: Viscosity, Brookfield: 300,000-400,000 cps @ 2 RPM Viscosity, Press Flow: 5-15 seconds @ 60 psi 25-45 seconds @ 30 psi 200-300 poise Sag Resistance: No sag with -185" bead DOLCHEM 601 5 : Viscosity, Brookfield: 120,000-140,000 @ 2 RPM 70,000- 90,000 @ 20 RPM Viscosity, Press Flow: 10-20 seconds @ 40 psi 200-300 poise Dry Time @ 68F; 50% RH: 5 minutes set to touch 72 hours through dry

Dolphin Paint and Chemical Go.


DOLCHEM 6098:

High Thix Weld Through Sealant An air dry, non flowing, oleoresinous sealant formulated for application to vertical steel parts prior to spot weld assembly. This sealant permits welding with conventional spot welders; it prevents moisture and oxygen from entering the joint and provides corrosion protection to the "hidden" joint that cannot be coated with primer. The sealant "disappears" from the area of the weld but remains tightly surrounding the weld spot; weld strengths are unchanged by the use of DOLCHEM 6098. This sealant has found wide use on many types of steel, including stainless. If squeezed to an exposed joint, it will not bleed through most primers and paints. Properties: Specific Gravity: 1.43-1.47 Color: Aluminum Solids: 87-89% Flash Point: 103F Viscosity, Press Flow: 5-15 seconds @ 60 psi 15-35 seconds @ 30 psi Sag Resistance: No sag with .625" bead Dry Time @ 68F; 50% RH: More than 72 hours set to touch Does not dry through The following tests were performed after drying 21 days (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Self extinguishing within 1''

@

68F

149

1 5 0 Prepaint Spmialties and Surface Tolerant Coatings

DOLPHIN PAINT & CHEMICAL CO.,

INC.:

WLCHEM 6099:

Epoxy Urethane Anti-Corrosion Sealant An air curing, low viscosity, sag resistant sealant formulated to prevent galvanic reactions between dissimilar metals. This product was designed for easy application to tight joints in aluminum to stainless steel assemblies; even in thin films, it prevents electrolytic corrosion. It adheres firmly to most metal surfaces; it cures through to withstand severe vibration and centrifugal force. This sealant's low viscosity and high thixotropy allow it to be brushed or pumped into small openings while preventing it from running or slumping out of the joint before drying. DOLCHEM 6099 has excellent exterior durability; it will withstand long term exposure to temperatures above 200F and below -20F. It can be painted over after a skin has formed and will not bleed through nor discolor most industrial enamels or automotive finishes. Properties: Specific Gravity: 1.20-1.24 Color: Gray Solids: 64-66% Flash Point: 69F Viscosity, Brookfield: 60,000-100,000 cps @ 2 RPM 10,000- 15,000 CPS @ 20 RPM Sag Resistance: No sag with .125" bead Dry Time @ 68F; 50% RH: 3 hours set to touch 48 hours through dry The following tests were performed after drying 21 days (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Self extinguishing within 1"

@

68F



DOLCHEM 6100:

Plastisol Structural Adhesive/Sealant A high strength, heat cured, vinyl sealant which adds to the structural strength of vehicle assemblies upon cure; this plastisol may be applied prior to spot welding and welded through, or pumped into the joint after welding. Its ultra high thixotropy prevents slumping from even large gaps. DOLCHEM 6100's ability to bond to even oily metal permits use in "body in white"; it will not wash out during phosphatizing nor during electrodecomposition priming of the assembled vehicle; and its thermal stability permits cure during epoxy primer bakes. This product is formulated to give excellent adhesion to oily metal, phosphatized cold rolled steel, aluminum and many electrodeposition epoxy primers; it is designed with adhesive strength greater than cohesive strength to provide excellent corrosion protection. DOLCHEM 6100 has also proven itself as a paintable body sealant; its high thixotropy enables this plastisol to fill and seal vertical drip rails and large body joints. It is paintable with most automotive enamels and will not cause discoloration, softening or cracking of the top coat, nor will it support the growth of mildew. Properties: Specific Gravity: 1.32-1 -36 Solids: 98% minimum Viscosity, Brookfield: 750,000-1,250,000 cps @ 2 RPM Viscosity, Press Flow: 5-15 seconds @ 60 psi 150-400 poise Sag Resistance: No sag after -625" bead The following tests were performed after baking 60 minutes @ 315F (157C): Adhesion, Shear: 1200 psi on 1000 psi on 1200 psi on Hardness, Shore D Durometer: Tensile Strength: 1200 psi Elongation: 300% Low Temperature Flexibility:

CRS aluminmum E-coated steel 30

No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Self extinguishing within 1"

151



DOLCHEM 6110/DOLCHEM 6115:

Plastisol Body Sealants These heat cured, vinyl sealants are proven performers in cosmetically sealing exposed body sheet metal joints on vehicle bodies. These non-shrinking sealants can be painted over and will cure during paint bakes of 300F or above; they have found use on assembly lines with sealer bake ovens prior to painting and on lines where the top coat is applied to the wet plastisol and the sealer and paint are cured together. DOLCHEM 6110 and 6115 are formulated to give excellent adhesion to most electrodeposition epoxy primers; their adhesion is greater than their cohesive strength to provide excellent sealing and corrosion protection. These sealants have demonstrated their ability to withstand vibration, flexing, sunlight and salt spray exposure under automotive baking enamels and lacquers in years of service on truck cabs; they do not cause discoloration, softening, or cracking of the top coat, nor do they support the growth of mildew. DOLCHEM 6110 is a non-flowing sealant for use on vertical joints and seams; it can easily be smoothed to "hide" joints under paint. DOLCHEM 6115 is a self-leveling sealant for use in horizontal applications, such as drip rails; it flows into hidden seams and presents a smooth top surface for optimum appearance under paint. Properties: Specific Gravity: 1.5-1.56 Solids: 98% minimum DOLCHEM 61 1 0: Viscosity, Brookfield: 600,000-1,100,000 cps @ 2 RPM Viscosity, Press Flow: 15-25 seconds @ 60 psi 40-55 seconds @ 30 psi 450-700 poise Sag Resistance: No sag with .25" bead DOLCHEM 61 1 5 : Viscosity, Brookfield: 20,000-30,000 cps @ 2 RPM 5,000-13,000 CPS @ 20 RPM Viscosity, Press Flow: 5-10 seconds @ 60 psi 15-30 seconds @ 30 psi (50-100 poise) Flow Characteristics: Self leveling The following tests were performed after baking 15 minutes @ 340F (171C): Adhesion, Shear: 500 psi on Uniprimed steel 500 psi on E-coated steel Hardness, Shore A Durometer: 55-60 Tensile Strength: 400 psi Elongation: 500% Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion


153

DOLPHIN PAINT & CHEMICAL CO.: DOLCHBM 6200 Series: Acrylic Latex Sealants These air dry, flexible, acrylic sealants have been formulated for use in vehicle assembly where flammability and/or environmental restrictions prevent the use of sealants containing solvents and production facilities do not include finish curing ovens. These non-sagging, solvent free sealants dry as fast as many solvent containing sealants and adhere as well to most of the materials used in vehicle construction, including stainless steel, aluminum, primed aluminum, prefinished aluminum, most electrodeposition epoxy primers, and most industrial enamel finishes. The acrylic polymer used in the compounding of these sealants provides them with excellent exterior durability and prevents discoloration from exposure to sunlight when used without painting. These sealants may be painted with air dry, forced dry or low cure enamels; they will not cause discoloration, softening or cracking of the top coat. The WLCHEM 6200 Series of Acrylic Latex Sealants has proven their ability to withstand vibration, flexing, sunlight and salt spray exposure through years of service on transit busses and recreational vehicles. Properties: Specific Gravity: 1.53 Color: Three colors available plus custom color matches DOLCHEM 6202 - Gray WLCHEM 6203 - White DOLCHEM 6204 - Black Solids: 75-77% Viscosity, Press Flow: 15-25 seconds @ 60 psi 70-100 seconds @ 30 psi Sag Characteristics: No sag with -625" bead Dry Time @ 25C; 50% RH: 10 minutes set to touch 24 hours through dry The following tests were performed after drying 21 days @ 60F (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion Humidity Resistance: No aorrosion under sealer No loss of adhesion Flammability: Pass Self extinguishing



DOLCHEM 6451:

Clear, Fast Dry, Adhesive/Sealant This fast setting, elastomeric adhesive/sealant was designed to bond foam rubber weather stripping to "base/clear" automotive finishes; it clarity permits the finish color to show through the adhesive along the edge of the weather strip for a "cleaner" appearance. Since its development, it has found application as a clear repair sealant for use on visible areas of auto bodies. DOLCHEM 6451's fast setting characteristic enables it to be used immediately before water test to seal leaks that are found. Its thixotropy permits the sealing of moderate gaps; its low viscosity permits it to be pumped into seams. The material will bond to glass, fiberglass and alumimum, in addition to automotive finishes and rubber. It may be painted over, if necessary; paints adhere well to this product and are not discolored or softened. In service, this adhesive/sealant will withstand vibration and flexing throughout range of environments and temperatures encountered by today's motor vehicle. Properties: Specific Gravity: .88-.92 Solids: 54-57% Flash Point: 26F Viscosity, Brookfield: 200,000-350,000 cps @ 2 RPM 100,000-1501000 CpS @ 20 RPM Viscosity, Press Flow: 35-55 seconds @ 30 psi 10-20 seconds @ 60 psi 200-450 poise Sag Resistance: No sag with .0625" bead Dry Time @ 68F, 50% RH: 10 minutes set to touch 24 hours through dry The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Adhesion, Peel: 18 lbs/inch from CRS Adhesion, Shear: 325 psi on CRS Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: Flexibility maintained No loss of adhesion

Dolphin Paint and Chemical Go.


155


Elastomeric Sealants The DOLCHEM 6520 Series offers tough, thermoplastic rubber adhesive/sealers with extra stabilizers for exterior applications. These stabilizers improve the ability of these compounds to withstand exposure to sunlight, salt spray, and high temperatures. This group of adhesive/sealants is available in a wide variety of colors, including custom color matches. These sealants bond to a wide variety of substrates; these include glass, fiberglass, steel, aluminum, rubber, and most primed and painted surfaces. The DOLCHEM 6520 Series of Elastomeric Sealants has found wide use in recreational vehicle and bus assembly in both interior and exterior applications. These products may be painted over, if necessary, paint adheres well to them and they do not discolor finishes. In service, these adhesive/sealers provide bond strengths as high as many "structural" adhesives with the ultimate in flexibility, even when exposed to extremely low temperatures. Properties: Specific Gravity: .91--96 Color: Nine colors available; plus custom color matches DOLCHEM 6522 - Alumimum DOLCHEM 6525 Black DOLCHEM 6529 - White DOLCHEM 6558 School Bus Yellow Solids: 60-64% Flash Point: 45F Viscosity, Press Flow: 15-30 seconds @ 60 psi 55-85 seconds @ 30 psi Sag Resistance: No sag with -25" bead Dry Time @ 68F; 50% RH: 10 minutes set to touch 36 hours through dry

-

The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Low Temperature Flexibility: No cracking No loss of adhesion Effects of Heat Aging: No discoloration No loss of adhesion Humidity Resistance: No corrosion under sealer No loss of adhesion Salt Spray Resistance: No corrosion under sealer No loss of adhesion Flammability: Pass Burn rate less than l"/min.

156 Prepaint *ecialties and surface Tolerant Coatings


DOLCHEM 6623:

Electrostat Enamel, Gray This fast drying, self priming, alkyd enamel is formulated for application with electrostatic spray equipment, but may also be applied with conventional spray equipment. This coating will cure at ambient temperatures to provide a hard finish with very good abrasion resistance and moisture resistance. DOLCHEM 6623 adheres to bare steel without priming or pre-treatment; when applied to treated metal, the coating's corrosion protection is significantly improved. The enamel's high pigment loading offers the user one coat coverage when properly applied. Complete cross-linking of the coating will be obtained by drying at room temperature; however, the coating may be forced dried, if desired. Properties: Specific Gravity: 1.05-1.08 Color: Gray Flash Point: 57F Viscosity, #2 Zahn Cup: 25-30 seconds Viscosity, Stormer: 67-70 ku Hiding, Pfund Cryptometer: 2200 sq. ft. per gal. Dry Time @ 20C; 50% RH: 3 Minutes Tack Dry 30 Hours - Through Dry

-

WLCHEM 6626: Machinery Enamel, Gray This air dry, alkyd enamel was formulated for excellent exterior durability. DOLCHEM 6626 will give a gloss finish to most metal surfaces; while it adheres well to most bare steels, the best durability is obtained when the metal is first primed with DOLCHEM 6661 or DOLCHEM 6694. This general purpose coating provides protection to the metal from water and salt spray through a wide temperature range; it withstands abrasions and substrate flexing. This easy to use paint provides an excellent appearance even when applied with a brush. This formulation can be color matched to almost any color standard. Properties: Specific Gravity: 1.20-1.23 Color: Medium Gray Flash Point: 104F Viscosity, Stormer: 61-63 ku Hiding, Pfund Cryptometer: 1500 sq. ft. per gal. Dry Time I? 20C; 50% RH: 15 minutes Tack Dry 4 hours - Through Dry

-


DOLPHIN PAINT I CHEMICAL CO.:

157

DOLCHEM 6640:

Exterior Paint, Lt. Elue This air dry, self priming, alkyd enamel is the easiest to use and most "forgiving" coating; it flows out to give a smooth, uniform coating no matter how sloppily it is applied. The paint was formulated for beautifying and protecting metal street light poles; it is normally applied with paint mitts in a wide variety of weather conditions by non-professional painters. DOLCHEM 6640 adheres to bare steel without priming; it also offers excellent adhesion to previously painted metal without sand blasting or chemical cleaning (loose and flaking paint should be brushed off before recoating). Complete hiding is normally achieved with one coat. DOLCHEM 6640 maintains its film integrity and color and provides years of protection in continuous outdoor exposure. DOLCHEM 6640's proven exterior durability and ease in application suggest its use in difficult to coat areas and for outdoor maintenance. This formulation can be color matched to almost any color standard. Properties: Specific Gravity: 1.02-1 - 0 5 Color: Light Blue Flash Point: 51F Viscosity, Stormer: 70-75 ku Dry Time @ 20C; 50% RH: 8 Minutes - Tack Dry 30 Minutes - Through Dry The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Specular Gloss: 30-40% Humidity Resistance: No blistering No loss of adhesion Salt Spray Resistance: No blistering No loss of adhesion QUV Exposure: No color change No surface change No loss of adhesion


WLPHIN PAINT & CHEMICAL CO.: DOLCHEM 6694: WELDTHRU ROX Primer An air dry, alkyd primer formulated for use on ferrous metals; it can be used on bare steel when thorough cleaning or pre-treatment are impossible and provides excellent intercoat adhesion when used on phosphatized metal. Because this primer can be spot welded through, it has found wide use in pre-coating metal parts before assembly; this coating provides good corrosion resistance even without a top coat and can provide protection to areas difficult to coat after assembly. DOLCHEM 6694 is especially useful when spot welding to stainless steel because it does not contain zinc which causes tip fouling during high temperature welding; DOLCHEM 6694 is preferred by those concerned with industrial safety and health because it does not contain lead or chrome. This low gloss formulation permits the use of a wide variety of top coat finishes; it can be lightly sanded for the application of ultra high gloss finishes. Properties: Specific Gravity: 1.18-1.21 Solids: 56-59% Flash Point: 75F Viscosity, #4 Ford Cup: 60-65 seconds Viscosity, Stormer: 61-63 ku Dry Time @ 20C; 50% RH: 15 minutes Tack Dry 2 hours - Through Dry

-

The following tests were performed after drying 21 days @ 68F (20C); 50% RH: Specular Gloss: 0-10% Hardness, Pencil Test: H Humidity Resistance: No blistering No adhesion loss



159

WLCHEM 6800 Series:

Flexible Paints for Rubber This series of very fast drying coatings was formulated to give excellent adhesion to a variety of rubber compounds plus flexibility and elasticity equal to the elastomer on which they are used. You have probably seen these products in use because this line of paints was designed for highlighting and decorating rubber mud flaps; the line has proven its colorfastness and exterior durability through more than twenty years of "over the road" performance. These products have also been used to color code rubber parts and to color tire side walls. The DOLCHEM 6800 Series is available in a wide range of colors; the base formulation can be color matched to almost any color standard. Properties: Specific Gravity: -92-1.20 Color: Nine colors available plus custom color matches DOLCHEM 6801 = Red DOLCHEM 6803 = Yellow DOLCHEM 6804 = White Flash Point: 45F Viscosity, Stormer: 75-80 ku Viscosity, Brookfield: 8,000-12,000 @ 2 RPM 2,000- 4,000 @ 20 RPM Dry Time @ 20C; 50% RH: 1 0 minutes tack dry 60 minutes through dry

160 Prepaint S;oecialtiesand Surface Tolerant Coatings

DOLPHIN PAINT & CHEMICAL CORP.:

DOLCHEM 6828:

High Temperature Resistant, Anti-Corrosion Coating An aluminum pigmented crosslinked, alkyd baking enamel for use on phosphated and primed metal parts that will be subjected to high temperature in service. This coating, when properly applied and baked, prevents corrosion by maintaining its adhesion and film integrity through the most severe service conditions even when subjected to service tmeperatures up to 600F. This formulation was developed to withstand the high service temperatures of aircraft engines and was originally used to color code aircraft spark plugs. Currently, this coating is also being used on automotive floor pans to prevent corrosion above the catalytic converter; this material has demonstrated its ability to prevent corrosion even after exposure to 600F followed by submersion in boiling salt water. This coating can also be used to indicate exposure to extreme temperatures as it turns gold when subjected to high heat. Properties: Specific Gravity: 0.905-0.925 Color: Aluminum Flash Point: 68F Viscosity, Stormer: 52-54 ku Viscosity, #4 Ford Cup: 30-36 seconds Gloss: 40-45% Hardness, Pencil: Gouge 3H Low Temperature Resistance: No cracking or loss of adhesion High Temperature Resistance: Turns gold No cracking or loss of adhesion Humidity Resistance: No corrosion No loss of adhesion Water Resistance: No corrosion No loss of adhesion Salt Spray Resistance: No corrosion No loss of adhesion

DuPont Maintenance Finishes

161

DUPONT MAINTENANCE FINISHES: CORLAR 825-007 Fast Dry Primer: Type: Epoxy Ester Description: A single package, quick-dry epoxy ester universal primer for steel. Will accept most topcoats and will not lift old coatings. Suggested Uses: - Shopcoat primer Where fast dry is required Can be used for spot repair

-

Not Recommended For: Immersion - Application over inorganic zinc

-

Compatibility With Other Coatings: Suggested topcoats: CORLAR Epoxy Enamels, IMRON Polyurethane Enamels, DULUX or DUPONT Alkyd Finishes, IMLAR Vinyls, TUFCOTE Acrylic Enamels, DUPONT Chlorinated Rubbers and DUPONT Industrial Acrylic Emulsions. Dry Film Characteristics: Weather - Excellent, will protect steel up to 12 months untopcoated. Good with appropriate topcoat. Chemical

-

Maximum Service Temperature: 200F (93C) in continuous service. Volume Solids: 46% Weight Solids: 6 8 % Weight Per Gallon: 12.1 Lb./5.5

Kg.

Suggested Film Build: 4 Mils (100 um) wet 2 Mils (50 um) dry Theoretical Coverage Per Gallon: 738 ft.2 (18.lm2/L) @ 1 mil 369 ft.2 (9.0m2/L) @ 2 mils suggested dry film thickness Gloss: Flat Colors: Red Oxide Flash Point (Tag Closed Cup): Less than -20F (-6C) Shelf Life: 12 months minimum Application Thinners: Spray: T-8005/Brush, Roll: T-8805 Clean Up Thinners: T-8805 or xylene


DUPONT MAINTENANCE FINISHES: CORLAR 825HB High Build Chromate Free Epoxy Primer 825-Y-9031: Type: Chromate Free, Epoxy Polyamide Description: A 2-packageI high build, chromate free heavy duty epoxy primer (activated with VF-Y-632) which is extremely durable and flexible. CORLAR 825 HB CF has excellent corrosion resistance and has been proven by years of exposure in very harsh environments such as chemical plants, pulp and paper mills, refineries, public utilities, etc. Certified by U.S.D.A. Suggested Uses: - Primer for clean mill-scale free steel in chemically harsh environments. - Intermediate coating over Inorganic Zinc. Not Recommended For: Immersion service Compatibility With Other Coatings: Compatible with most topcoats. Can be applied directly over old thermoset coatings in good condition. For application over other coatings, test for lifting. Dry Film Characteristics: Chemical - Excellent with appropriate topcoat. Humidity - Excellent Weather Excellent with appropriate topcoat. Water Spray Excellent

-

-

Maximum Service Temperature: 200F (93C) in continuous service. 300F (148C) in intermittent heat. Volume Solids (Mixed): 46% Weight Solids (Mixed): 65% Weight per Gallon (Mixed): 11.7 Lb.15.3 Kg. Suggested Film Thickness: 9 mils (225 um) wet 4 mils ( 1 0 0 um) dry Theoretical Coverage per Gallon: 737 ft.2 (18.0 m2/L) @ 1 mil 184 ft.2 (4.5 m2IL) @ 4 mils suggested dry film thickness Gloss: Flat Colors: Red Oxide Flash Point (Tag Closed Cup): Between 20-73F (-7 to 23C) Shelf Life: 12 months minimum Application Thinners: Spray: T-8819 or T-8054 Clean Up Thinners: T-8819 or MEK Packaging: 1 and 5 gallon containers


163

DUPONT MAINTENANCE FINISHES: DULUX 67-Y-834 Chromate Free Primer (VOC Conforming): Type: Chromate-Free, Linseed Oil, Alkyd primer Description: A slow drying, high solids, low VOC, zinc chromatefree, linseed oil alkyd primer for hand or blast cleaned steel. (Chrome free equivalent of 67-Y-746.) Certified by U.S.D.A. Suggested Uses: Prime over scale-bearing hand cleaned, or blasted steel. Not Recommended For: Shop priming or where rapid drying is important. Compatibility With Other Coatings: Topcoat with DULUX or DUPONT Alkyd Enamels, TUFCOTE Acrylic Enamels, or DUPONT Industrial Acrylic Emulsions. Dry Film Characteristics: Weather--Very Good Humidity--Very Good Chemical--Good with appropriate topcoat Maximum Service Temperature: 150F (65C) in continuous service Volume Solids: 64% Weight Solids: 82% Weight per Gallon: 13.1 Lb./5.9

Kg.

Suggested Film Thickness: 3 mils (75um) wet 2 mils (50um) dry Theoretical Coverage Per Gallon: 1026 ft2 (25.lm2/L) @ 1 mil 513 ft2 (12.5m2/L) @ 2 mils suggested dry film thickness Gloss: Flat Colors: Red-Brown Flash Point (Tag Closed Cup): Between 100-140F (37-6OC) Shelf Life: 12 months minimum Application Thinners: Spray: T-Y-3810 Brush, Roll: T-Y-3819 Clean Up Thinners: T-Y-3819 or mineral spirits

164


DUPONT MAINTENANCE FINISHES: DULUX 681 FD Chromate Free Primer (VOC Conforming): Type: Modified medium oil alkyd Description: Single package fast dry, low VOC, easy to apply primers and intermediate coats for use under IMRON, CORLAR, DULUX and other topcoats. Free of chromates and lead. Suggested Uses: - Shopcoat primer - Where fast dry is required - Spot repair primer - Intermediate coat - Machinery and equipment Not Recommended For: - Immersion service - Application over inorganic zinc Compatibility With Other Coatings: - Can be applied directly to steel or over most old coatings in good condition. - Can be topcoated with DULUX Alkyds, CORLAR Epoxies, TUFCOTE Acrylics or IMRON Polyurethanes. Resistance: Chemical - Very good with appropriate topcoat Weather - Excellent Humidity - Excellent Maximum Service Temperature: 150F (65C) in continuous service Volume Solids: 508 Avg. Weight Solids: 70% Avg. Weight per Gallon: 11.7 Lb. Avg.15.3 Kg. Avg. Suggested Film Build: 4 mils (100um) wet/2 mils (50um) dry Coverage Per Gallon: 795 Ft2 (19.5 m2/L) @ 1 mil 398 Ft2 (9.8 rn2/L) @ 2 mils suggested film build Gloss: Flat Colors: Red Oxide 681-704lBuff 681-705 Flash Point (Tag Closed Cup): 20-73F Shelf Life: 1 year minimum Application Thinners: Spray: T-Y-3819 Brush, Roll: T-Y-3819 Clean Up Thinners: T-Y-3819 or mineral spirits


165

DUPONT MAINTENANCE FINISHES: DUPONT 25P High Solids Epoxy Mastic: Type: Epoxy/Amine Modified Polyamide Description: DUPONT 25P is a two package (1:l mix) high solids, high build, VOC Conforming (2.2 lbs./gal), multi-use epoxy mastic coating. It provides outstanding application properties--no induction time, long pot life, can be applied in hot or cold weather, faster dry times, excellent film build on both flat surfaces and edges, goes over hand-cleaned rusty surfaces, can be applied over damp surfaces, most other coatings, and can be top-coated with a wide range of coatings. Its performance and durability are excellent under all conditions and environments. Suggested Uses: 25P is a multi-use product suitable for application in a variety of situations. - As a single coat in non-corrosive environments (5-8 mils DFT). - As a single coat in corrosive environments (10-12 mils DFT). - As a primer in 2 or 3 coat systems (3-8 mils DFT). - As an intermediate or mid-coat in a 3 coat system (4-6 mils DFT). Provides excellent durability and adhesion over steel, galvanized steel, masonry--concrete, and wood. Recommended For Immersion Service: 25P is recommended for immersion service in near neutral, fresh, or salt water exposures. It is not recommended for use with potable water. It may be used for fire water towers, ballast tanks, barge and ship hulls, clarifiers, waste water treatment plants, offshore structures, pier pilings and supports, and other areas where a high level of water resistance is required. Compatibility With Other Coatings: - 25P is highly compatible with all generic types of coatings. - It can be applied over most coatings in sound condition such as GANICIN inorganic/organic zincs, CORLAR epoxies, IMRON polyurethanes, DUPONT 50P, DULUX alkyds, vinyls, chlorinated rubbers, acrylics, and latexes. If in doubt, apply a test patch before painting. It can be topcoated by itself and other coating types listed above. Maximum Service Temperature: 200F (93C) in continuous service 300F (148C) in intermittent heat Volume Solids (Mixed): 70% Avg. Weight Solids (Mixed): 82% Avg. Weight Per Gallon (Mixed): 11.8 Lb. Avg./5.4 Kg. Avg. Suggested Film Build (DFT): Single Coat--5-8 mils in noncorrosive environment/l0-12 mils in corrosive environment and immersion service Primer--3-8 mils Mid-Coat--4-6 mils Coverage Per Gallon: 1122 Ft2 @ 1 mil DFT Gloss: Satin Finish

-

-

166 Prepaint Specialtis and Surface Tolerant Coatings

DUPONT MAINTENANCE FINISHES: GANICIN 347-Y-912 Inorganic ZincRich Coating: Type: 2-Package Inorganic Zinc Description: An alkyl silicate, two-component inorganic zincrich coating consisting of 347-Y-A001 liquid and 347-Y-B912 zinc dust for abrasive blast cleaned steel. Contains 85% zinc by weight in the dried film Suggested Uses: Primer for abrasive blast cleaned steel Not Recommended For: Application by brush or roller Stainless steel Acid or alkali environments without suitable topcoat Compatibility With Other Coatings: Topcoat with IMRON Polyurethanes, CORLAR Epoxies, DUPONT Industrial Acrylic Emulsions, and DUPONT 25P. Dry Film Characteristics: Chemical Resistance--Excellent when topcoated Water Spray--Excellent Humidity--Excellent Weather--Excellent Salt--Excellent Maximum Service Temperature: 750F (398C) in continuous service. Weight Solids (Mixed): 78% Weight Per Gallon (Mixed): 18.8 Lb./8.5 Kg. Suggested Film Thickness: 5 mils (125um) wet 3 mils (75um) dry Theoretical Coverage Per Gallon: (based on void content method): 865 ft2 (21.6m2/L) @ 1 mil 288 ft2 (7.2m2/L) @ 3 mils suggested dry film thickness Gloss: Flat Colors: Gray-Green Flash Point (Tag Closed Cup): Between 20-73F (-7 to 23C) Shelf Life: 12 months minimum Application Thinners: Spray: T-Y-3826 or 39798 Clean Up Thinners: T-Y-3826 or MEK


167

DUPONT MAINTENANCE FINISHES: GANICIN 347-Y-931 Inorganic ZincRich Coating: Type: 2-Package Inorganic Zinc Description: An alkyl silicate, two-component inorganic zincrich coating consisting of 347-Y-A001 liquid and 347-Y-B391 zinc dust for abrasive-blast cleaned steel. Contains 88% zinc by weight in the dried film. Certified by USDA. Suggested Uses: Primer for abrasive blast cleaned steel Single coat system for use in mild or salt air environments

-

Not Recommended For: - Application by brush or roller - Stainless steel - Acid or alkali environments without suitable topcoat Compatibility With Other Coatings: Topcoat with IMRON Polyurethanes, CORLAR Epoxies, DUPONT Industrial Acrylic Emulsions, DUPONT Silicones and DUPONT Silicone-Acrylic Enamels or DUPONT Chlorinated Rubbers. Dry Film Characteristics: Chemicals - Excellent when topcoated Water Spray Excellent Humidity - Excellent Weather - Excellent Salt - Excellent

-

Maximum Service Temperature: 750F (398C) in continuous service Volume Solids (Mixed): 44% Weight Solids (Mixed): 81% Weight Per Gallon (Mixed): 21.8 Lb./9.9 Kg. Suggested Film Thickness: 5 mils (125 um) wet 3 mils (75 um) dry Theoretical Coverage Per Gallon: (based on void content method) 1080 ft2 (26.5 m2/L) @ 1 mil 360 ft2 (8.8 m2/L) @ 3 mils suggested dry film thickness Gloss: Flat Colors: Gray-Green Flash Point (Tag Closed Cup): Between 20-73F (-7 to 23C) Shelf Life: 12 months minimum Application Thinners: Spray: T-Y-3826 or 39793 Clean Up Thinners: T-Y-3826 or MEK


DUPONT MAINTENANCE FINISHES: IMRON 62 Polyurethane Primer:

Type: 2-Package, Oil Free, Aromatic Polyurethane Description: An easily applied, high build, extremely durable, 2package polyurethane primer consisting of pigmented base 62-Y-001 and VG-Y-250 activator. Free of lead and chrome pigments. Provides excellent edge coverage. IMRON 62 can be used on abrasive blasted, hand tool cleaned or power tool cleaned substrates. Suggested Uses: Primer over blasted or hand tool cleaned steel. - Intermediate coat over inorganic zinc to minimize bubbling. - Can be used directly over galvanized steel or aluminum.

-

Not Recommended For: - Used under alkyd enamels or vinyl coatings High abrasion areas

-

Compatibility With Other Coatings: Can be topcoated with IMRON Polyurethane Enamels and CORLAR Epoxy Enamels. Can be applied over most old coatings in good condition. (Has minimal tendency to lift.) Dry Film Characteristics: Weather - Excellent when topcoated Humidity Excellent Chemical Excellent Acids - Excellent Alkali - Excellent Salts - Excellent Solvents - Very Good Water spray - Excellent

-

Maximum Service Temperature: 200F (93C) in continuous service. 300F (148C) in intermittent service. Volume Solids (Mixed): 50% Weight Solids (Mixed): 66% Weight per Gallon (Mixed): 11.4 Lb./5.2 Kg Suggested Film Thickness: 10 mils (250 um) wet 5 mils (125 um) dry Theoretical Coverage Per Gallon: 802 ft.2 19.7 m2/L) @ 1 mil Gloss: Flat Colors: Dark Brown Flash Point (Tag Closed Cup): Between 20-73F (-7 to 23C) Shelf Life: Primer - 12 months minimum Activator - 6 months minimum Application Thinners: Spray: Y-32035 or 3979s Brush, Roll: Y-32035 or 39795 Clean Up Thinners: Y-32035 or MEK

Dutch Boy Paints

169

DUTCH BOY PAINTS: CONFIDENT Exterior Latex Primer: An acrylic latex primer for exterior surfaces. Typical Uses: Recommended for exterior wood siding, shakes, shingles, trim, concrete, and cinder or cement block. May be applied to galvanized surfaces. Performance: - Prolongs life of house paint - Excellent adhesion - Resists wood staining - Quick drying - Excellent hiding - Soap and water cleanup Characteristics: Finish: Flat Colors: White Dryinq - - Time ( @ 77F -~

To Touch: 1 / 2 hour To Recoat: 2 - 4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1.4 mils dry Volume Solids (White): 35.6% Weight Solids (White): 45.8% Weight/Gal. (White): 9 . 9 9 - U ~ . Vehicle Type: Acrylic Flash Point: 201F P.M. Closed Cup Tinting: Up to 4 oz. per gallon with BLEND-A-COLOR or SPECTRAL Colorants. &

50% R.H.):

Surface Preparation: All surfaces must be clean, sound and dry before painting. Previously Painted Surfaces: Wash off dirt and chalk with detergent and water. Scrape away loose paint and sand smooth. Fill holes and cracks. On masonry, remove all mastic, powdery, thick layered, peeling or heavily chalked oil paint by sandblasting or power brushing. Unpainted Surfaces: Wood: Countersink and putty nailheads. Masonry: Must be cured and free of water for best adhesion. Galvanized Metal should be primed with 1 coat DIRT FIGHTER Exterior Latex Primer. Application and Reduction: Protect from freezing. Apply at temperatures above 50F. Brush full body. For conventional spray reduce with up to 1 1 2 pint of water per gallon if necessary. For airless spray reduce with up to 1 / 2 pint of water per gallon if necessary.


DUTCH BOY PAINTS: CONFIDENT Exterior Oil/Alkyd Wood Primer: An alkyd white undercoater Typical Uses: Recommended for wood siding, clapboard, trim, shakes and shingles. Use on composition or hardboard, even if factory primed. Performance: - Good adhesion - Stops wood staining (even on bleeding woods such as redwood and cedar) - Excellent penetration - Prolongs life of house paints - Use under latex or oillalkyd paints Characteristics: Finish: Flat 5-15 units @ 60 Color: White Dryinq - - Time (@77F & 50% R.H.):

To Touch: 2-4 hours To Recoat: 24 to 48 hours Spreading Rate: 400 sq. ft. per gal. Q 4 mils wet 2.3 mils dry Volume Solids: 55.0% Weight Solids: 73.6% WeiqhtIGal.: 10.98 lb. Vehicle Type: Alkyd Flash Point: 115F PM Closed Cup Tinting: up to 4 oz. gal. with BLEND-A-COLOR or SPECTRAL Colorants

Surface Preparation: All surfaces must be clean, sound and dry before painting. Unpainted Surfaces: Wobd and factory primed siding should be primed and allowed to dry. Composition Board or hardboard must be primed with Exterior OilIAlkyd Wood Primer whether it is unprimed, factory primed or pre-primed. Pressure Treated Wood must weather until all greenish-tone surface salts are gone. Previously Painted Surfaces: Scrape away loose and peeling paint and sand bare wood to fresh clean surface. Wash off dirt and chalk with detergent and water. Fill holes or cracks. Badly weathered and heavily chalked surfaces should be primed with one coat of Exterior OilIAlkyd Wood Primer. Application and Reduction: Temperature must be 50F and above. Brush full body. For coventional spray reduce with up to 1 pint of mineral spirits or paint thinner per gallon. For airless spray use full body.

Dutch Boy Paints

171

DUTCH BOY PAINTS: CONFIDENT Interior Latex Wall Primer: A white pigmented vinyl acrylic latex primer. Typical Uses: Recommended for walls and ceilings. Use on wallboard or drywall, and masonry. Do not use on-bare plaster. Performance: Both enamel undercoat and wall primer and sealer. - Use under latex or oillalkyd paints - Sands smooth without clogging sandpaper - Seals surface of wallboard and lays down nap - Good hiding white Soap and water cleanup

-

Characteristics: Finish: Matte flat Colors: White Drying Time ( @ 77F

To Touch: 1 hour To Recoat: 3-4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1.2 mils dry Volume Solids: 30.3% Weight Solids: 42.8% WeightIGal.: 10.11 lbs. Vehicle Type: Vinyl Acrylic Latex Flash Point: 201F P.M. Closed Cup Tinting: up to 4 02. per gal. with BLEND-A-COLOR or SPECTRAL Colorants. &

50% R.H.):

Surface Preparation: Surface must be smooth, clean and free of oil, dirt and dust. Unpainted Surfaces: On drywall patch cracks and holes with spackling paste. On wood fill nail holes and allow to dry. Masonry (brick, concrete, etc.) must be cured and dry. Previously Painted Surfaces: No primer is required if in sound condition and of uniform porosity. Dull glossy surfaces by sanding with fine sandpaper or steel wool or wash with an abrasive cleanser and rinse well. Patched and bare areas must be clean and spot-primed before painting entire surface. Application and Reduction: It is recommended that the primer be tinted to the approximate shade of the topcoat. Paint at temperatures above 50F. Roll or brush full body. For conventional spray reduce with up to 112 pint of water per gallon. For airless spray use full body. Cleanup: Clean hands, tools and equipment with warm soapy water.


DUTCH BOY PAINTS: CONFIDENT Interior Oil/Alkyd Wall Primer: A

&

Wood

white pigmented alkyd primer.

Typical Uses: Recommended for interior walls, ceilings, trims and floors. Use on new wood or plaster. May be used for repainting oil painted porous surfaces. Use on drywall or wallboard under wall covering. performance: Both enamel undercoat and wall primer and sealer. - Use under latex or oil/alkyd paints - Sand smooth without clogging sandpaper - Good adhesion - Good hold out Characteristics: Finish: Low angular sheen 3-15 units @ 85 Colors: White Drying Time ( @ 77F & 50% R.H.): To Touch: 1 - 2 hours To Recoat: 16 - 24 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1.6 mils dry Volume Solids: 39.3% Weight Solids: 64.5% WeightlGal. : 1 1 .14 lbs. Vehicle Type: Alkyd Flash Point: 105F P.M. Closed Cup Tinting: up to 4 oz. per gal. with BLEND-A-COLOR or SPECTRAL Colorants. Surface Preparation: Unpainted Surfaces: Wood must be clean, smooth, sanded and dust free. Plaster must be clean and free of grease, glue size and wallpaper paste. Masonry (brick and concrete) must be thoroughly cured and dry. Previously Painted Surfaces: No primer is required if in sound condition and of uniform porosity. Dull glossy surfaces by sanding with fine sandpaper or steel wool or wash with an abrasive cleanser and rinse well. Patched and bare areas must be clean and spot-primed before painting entire surface. Application and Reduction: It is recommended that oil/alkyd wall and wood primer be tinted to the approximate shade of the topcoat. Roll or brush full body. For conventional spray reduce with up to 112 pint of mineral spirits or paint thinner per gallon. For airless spray use full body.

Dutch Boy Paints

173

DUTCH BOY PAINTS: DIRT FIGHTER Exterior Latex Primer:

A quality acrylic latex primer for exterior surfaces. Recommended for exterior wood siding, shakes, shingles, trim, concrete, and cinder or cement block. May be applied to galvanized surfaces. Performance: - Prolongs life of house paint - Excellent adhesion Resists wood staining - Quick drying - Excellent hiding - White color covers easily with topcoat - Soap and water cleanup

-

Characteristics: Finish: Flat Colors : 'White Drying Time ( @ 77F

To Touch: 1/2 hour To Recoat: 2 - 4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1 . 4 mils dry Volume Solids (White): 35.6% Weight Solids (White): 45.8% Weight/Gal. (White): 9 . 9 9 lbs. Vehicle Type: Acrylic Flash Point: 201F P.M. Closed Cup Tinting: Up to 4 oz. per gallon with BLEND-A-COLOR or SPECTRAL Colorants & 50%

R.H.):

Surface Preparation: All surfaces must be clean, sound and dry before painting. Previously Painted Surfaces: Wash off dirt and chalk with detergent and water. Scrape away loose paint and sand smooth. Fill holes and cracks. Unpainted Surfaces: Wood - Countersink and putty nailheads. Masonry - Must be cured and free of water for best adhesion. Galvanized Metal should be primed with 1 coat DIRT FIGHTER Exterior Latex Primer. Application and Reduction: Protect from freezing. Apply at temperatures above 50F. Brush full body. For conventional spray reduce with up to 1/2 pint of water per gallon if necessary. For airless spray reduce with up to 1/2 pint of water per gallon if necessary.

174 Prepaint apecialties and Surface Tolerant Coatings

DUTCH BOY PAINTS: DIRT FIGHTER Exterior Oil/Alkyd Wood Primer: Quality alkyd white undercoater Typical Uses: Recommended for wood siding, clapboard, trim, shakes and shingles. Use on composition or hardboard, even if factory primed. Performance: - Excellent adhesion - Stops wood staining (even on bleeding woods such as redwood and cedar) - High hiding white - Excellent penetration - Prolongs life of house paints - Use under latex or oillalkyd paint Characteristics: Finish: Flat Color: White Drying Time ( @ 77F

To Touch: 2-4 hours To Recoat: 24-40 hours Spreading Rate: 4 0 0 sq. ft. per gal. @ 4 mils wet 2 . 3 mils dry. Volume Solids: 5 7 . 4 % Weight Solids: 7 6 . 4 % Weight/Gal.: 1 1 . 4 9 lb. Vehicle Type: Alkyd Flash Point: 105F PM Closed Cup Tinting: up to 4 oz. gal. with BLEND-A-COLOR or SPECTRAL Colorants &

50% R.H.):

Surface Preparation: All surfaces must be clean, sound and dry before painting. Unpainted Surfaces: Wood and factory primed siding should be primed and allowed to dry. Composition Board or hardboard must be primed with Exterior Oil/Alkyd Wood Primer whether it is unprimed, factory primed or pre-primed. Previously Painted Surfaces: Scrape away loose and peeling paint and sand bare wood to fresh clean surface. Wash off dirt and chalk with detergent and water. Fill holes or cracks. Badly weathered and heavily chalked surfaces should be primed with one coat of Exterion OilIAlkyd Wood Primer. Application and Reduction: Temperature must be 50F and above. Brush full body. For conventional spray reduce with up to 1 pint of mineral spirits or paint thinner per gallon. For airless spray use full body.

Dutch Boy Paints

175

DUTCH BOY PAINTS: DIRT FIGHTER Interior Latex Wall & Wood

Primer: A quality white pigmented vinyl acrylic latex primer. Typical Uses: Recommended for walls, ceilings and trim. Use on wallboard or drywall, wood and masonry. Do not use on bare plaster. Performance: Both enamel undercoat and wall primer and sealer. Use under latex or oillalkyd paints Sands smooth without clogging sandpaper - Seals surface of wallboard and lays down nap - Seals wood when water soluble staining is not a problem - High hiding white - Excellent hold out Soap and water cleanup

-

Characteristics: Finish: Matte flat 0-10 units Colors: White Drying Time ( @ 77F & 50% R.H.):

@

60

To Touch: 1 hour To Recoat: 3-4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1.0 mils dry Volume Solids: 23.8% Weight Solids: 37.6% Weight/Gal.: 10.17 lbs. Vehicle Type: Vinyl Acrylic Latex Flash Point: 201F P.M. Closed Cup Tinting: up to 4 0 2 . per gal. with BLEND-A-COLOR or SPECTRAL Colorants. Surface Preparation: Surface must be smooth, clean and free of oil, dirt and dust. Unpainted Surfaces: On drywall patch cracks and holes with spackling paste. On wood fill nail holes and allow to dry. Masonry (brick, concrete, etc.) must be cured and dry. Previously Painted Surfaces: No primer is required if in sound condition and of uniform porosity. Dull glossy surfaces by sanding with fine sandpaper or steel wool or wash with an abrasive cleanser and rinse well. Patched and bare areas must be clean and spot-primed before painting entire surface. Application and Reduction: It is recommended that the primer be tinted to the approximate shade of the topcoat. Paint at temperatures above 50F. Roll or brush full body. For conventional spray reduce with up to 112 pint of water per gallon. For airless spray use full body.


DUTCH BOY PAINTS: DIRT FIGHTER Interior Oil/Alkyd Wall Primer:

&

Wood

A quality white pigmented alkyd primer. Typical Uses: Recommended for interior walls, ceilings, trim and floors. Use on new wood or plaster. May be used for repainting old painted porous surfaces. Use on drywall or wallboard under wall covering. Performance: Both enamel undercoat and wall primer and sealer. - Use under latex or oil/alkyd paints - Sand smooth without clogging sandpaper Excellent adhesion - High hiding white - Excellent holdout

-

Characteristics: Finish: Low angular sheen 3-15 units @ 6 0 Colors: White Drying Time ( @ 77F & 5 0 % R.H.): To Touch: 1 - 2 hours To Recoat: 1 6 - 2 4 hours Spreading Rate: 4 0 0 sq. ft. per gal. @ 4 mils wet 1 . 6 mils dry Volume Solids: 3 9 . 3 % Weight Solids: 6 4 . 5 % WeightIGal. : 1 1 .I 4 lbs. Vehicle Type: Alkyd Flash Point: 105F P.M. Closed Cup Tinting: up to 4 oz. per gal. with BLEND-A-COLOR or SPECTRAL colorants. Surface Preparation: Unpainted Surfaces: Wood must be clean, smooth, sanded and dust free. Plaster must be clean and free of grease, glue size and wallpaper paste. Masonry (brick and concrete) must be thoroughly cured and dry Previously Painted Surfaces: No primer is required if in sound condition and of uniform porosity. Dull glossy surfaces by sanding with fine sandpaper or steel wool or wash with an abrasive cleanser and rinse well. Patched and bare areas must be clean and spot-primed before painting entire surface. Application and Reduction: It is recommended that oil/alkyd wall and wood primer be tinted to the approximate shade or the topcoat. Roll or brush full body. For conventional spray reduce with up to 112 pint of mineral spirits or paint thinner per gallon. For airless spray use full body.

Dutch Boy Paints

177

DUTCH BOY PAINTS: DIRT FIGHTER Latex Universal Primer: A quality interior/exterior primer for wood or metal surfaces. Typical Uses: Recommended for exterior wood siding, shakes, shingles, trim, concrete, and cinder or cement block. Also recommended for metal surfaces, including galvanized metal. May also be used on interior drywall or wallboard construction or masonry. Performance: - Prolongs life of topcoats Excellent adhesion Resists wood staining - Rust inhibitive - Excellent hiding - Soap and water cleanup

-

Characteristics: Finish: Flat Colors: White Drying Time ( @ 77F

To Touch: 1/2 hour To Recoat: 2-4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet 1.6 mils dry Volume Solids (White): 39.8% Weight Solids (White): 51.7% Weight/Gal. (White): 10.4 lbs. Vehicle Type: Acrylic Flash Point: 201F P.M. Closed Cup Tinting: Up to 4 oz. per gallon with BLEND-A-COLOR or SPECTRAL Colorants. &

50% R.H.):

Surface Preparation: All surfaces must be clean, sound and dry before painting. Previously Painted Surfaces: Wash off dirt and chalk with detergent and water. Scrape away loose paint and sand smooth. Fill holes and cracks. On masonry, remove all mastic, powdery, thick layered, peeling or heavily chalked old paint by sandblasting or power brushing Unpainted Surfaces: Wood: Countersink and putty nailheads. Masonry: Must be cured and free of water for best adhesion Galvanized Metal should be primed with 1 coat DIRT FIGHTER Universal Latex Primer. Application and Reduction: Protect from freezing. Apply at temperatures above 50F. Brush full body. For conventional spray reduce with up to 1/2 pint of water per gallon if necessary. For airless spray reduce with up to 1/2 pint of water per gallon if necessary.


DUTCH BOY PAINTS: DIRT FIGHTER Oil/Alkyd Masonry Conditioner:

A penetrating alkali resistant sealer for use over masonry surfaces. Typical Uses: Exterior masonry surfaces of stucco, block, brick, plaster and asbestos shingles. Oil/Alkyd Masonry Conditioner penetrates chalk and forms a bond with the surface below, providing a good foundation for finish coats. Performance: - Promotes adhesion on lightly chalking masonry Bonds paint to weathered masonry - Helps prevent peeling paint on old masonry

-

Characteristics: Color: Clear Drying Time ( @ 77F

To Touch: 2 - 4 hours To Recoat: 24 hours Spreading Rate: 150-250 sq. ft. per gallon, depending on porosity of surface. Volume Solids: 39.0% Weight Solids: 46.5% Weight/Gal.: 7.28 lbs. Vehicle Type: Alkyd Flash Point: 105F P.M. Closed Cup Tinting: Up to 2 02. per gallon with BLEND-A-COLOR or SPECTRAL Colorants. &

50% R.H.):

Surface Preparation: Wash off dust, dirt and loose chalk with detergent and water. Remove loose surface chalk, powder and peeling paint by wire brushing or sandblasting. Patch cracks, holes, and broken cement. Application and Reduction: Apply at temperatures above 50F. Reduce with paint thinner or mineral spirits. Heavily porous masonry surfaces will require less reduction to penetrate. Do not mix Oil/Alkyd Masonry Conditioner with other paints. May be tinted with up to 2 oz. of colorant per gallon as a guide Brush or roll reduced up to 50% with paint thinner or mineral spirits. For conventional spray, reduce as needed. For airless spray, reduce as needed. Cleanup: Clean hands, tools, and equipment with paint thinner or mineral spirits.

Dutch Boy Paints

179

DUTCH BOY PAINTS: Interior Latex ALL PREP: A latex surface preparation for use under wallcovering. Typical Uses: Recommended for interior walls and ceilings. Use on wallboard or drywall, plaster and wallpaper. Performance: - Prepares walls for wallpaper - For under all wallpapers - Fast dry - Makes future removal of wallpaper easier - Soap and water cleanup Characteristics: Finish: Flat Color: Bluish White Drying Time: (@77F & 5 0 % R.H.):

To Touch: 1 hour To Wallpaper or Recoat: 2 hours Spreading Rate: 700-800 sq. ft. per gallon (1 gallon for 20 single rolls of wallpaper) Volume Solids: 15.0% Weight Solids : 1 9 . 9 % WeightIGal.: 8.85 lbs. Vehicle Type: Acrylic Flash Point: 201F P.M. Closed Cup

Surface Preparation: Wash off all dirt, grease, soap and oil with powdered cleaner and water rinse and allow to dry. Remove all loose or peeling paint by scraping or wire brushing Paste down loose sections of old wallpaper. Old wallpaper must be firmly adhered to surface. Application and Reduction: Roll or brush full body. Cleanup: Clean hands, tools and equipment with warm, soapy water. Flush spray equipment with paint thinner or mineral spirits to prevent rusting, following manufacturer's safety instructions.


DUTCH BOY PAINTS: Interior Varnish Sanding Sealer: Clear Semi-gloss A vinyl toluene copolymer clear semi-gloss sealer. Typical Uses: Recommended for interior woodwork, doors, paneling and cabinets. Use on bare wood. May be used as a sealer or as a finish coat. not for use under polyurethane varnishes or as a finish coat on floors. Performance: Sands easily - Prevents Raising of Grain Dries Fast - Excellent Sealer - Excellent Hold Out - Hay be Tinted

-

Characteristics: Finish: Semi-gloss 45-65 units @ 6 0 Drying Time ( @ 77F & 50% R.H.): To Touch: 1 / 2 hour To Sand and Recoat: 2-3 hours Spreading Rate: 350 sq. ft. per gallon on porous and rough surfaces 500 sq. ft. per gallon on sealed surfaces 1 mil film thickness with no loss in application allowed for. Volume Solids: 27.8% Weight Solids: 34.6% Weight/Gallon: 6.91 lbs. Vehicle Type: Vinyl Toluene Copolymer Flash Point: 52F P.M. Closed Cup Tinting: 1 oz per gallon with BLEND-A-COLOR or SPECTRAL Colorants Surface Preparation & Application: Wash surface to remove all dirt and grease. Sealer over Natural or Stained Wood: Apply full body for uniform sealing. Varnish Finish Coat: Apply full body and sand as desired. Varnish Stain-Sealer: Tint Varnish Sanding Sealer with up to 1 oz. per gallon BAC or SPECTRAL Colorants. Wash Coat Sealer to Control Wild Grain of Plywood: Reduce Varnish Sanding Sealer with equal parts of Mineral Spirits or paint thinner. Application and Reduction: Temperature must be 50F or above. Brush using a clean, soft fine bristle brush. Roll on horizontal surfaces only. For conventional spray reduce with up to 1 pint paint thinner, mineral spirits or VM&P naphtha per gallon. For airless spray use full body. This product meets all present lead hazard regulations.

Dutch Boy Paints

181

DUTCH BOY PAINTS: Professional Architectural Exterior Oil/Alkyd Wood Primer: An alkyd white undercoater for exterior use. Typical Uses: Recommended for wood siding, clapboard, trim, shakes and shingles. Use on composition or hardboard, even if factory primed

.

Performance: - Excellent adhesion - stops wood staining (even on bleeding woods such as redwood and cedar) - High hiding white - Excellent penetration - Professional quality product - Use under latex or oil/alkyd paints Characteristics: Finish: Flat Color: White Drying Time ( @ 77F & 50% R.H.):

To Touch: 2-4 hours To Recoat: 24 to 48 hours Spreading Rate: 4 0 0 sq. ft. per gal. @ 4 mils wet 2.2 mils dry Volume Solids: 55.0% Weight Solids: 73.6% Weight/Gal.: 10.98 lbs. Vehicle Type: Alkyd Flash Point: 105F PM Closed Cup Tinting: up to 4 oz. gal. with BLEND-A-COLOR or SPECTRAL colorants Surface Preparation: All surfaces must be clean, sound and dry before painting. Unpainted Surfaces: Wood and factory primed siding should be primed and allowed to dry. Composition Board or hardboard must be primed with Exterior Oil/Alkyd Wood Primer whether it is unprimed, factory primed or pre-primed. Pressure Treated Wood must weather until all greenish-tone surface salts are gone. Previously Painted Surfaces: Scrape away loose and peeling paint and sand bare wood to fresh clean surface. Wash off dirt and chalk with detergent and water. Fill holes or cracks. Badly weatherd and heavily chalked surfaces should be primed with one coat of Exterior Oil/Alkyd Wood Primer. Application and Reduction: Temperature must be 50F and above. Brush full body. For conventional spray reduce with up to 1 pint of mineral spirits or paint thinner per gallon. For airless spray use full body.


DUTCH BOY PAINTS: Professional Architectural Interior Latex Wall Primer: A vinyl acrylic latex sealer. Typical Uses: Interior walls, ceilings and trim. For residential or commercial use. Use on wallboard or drywall, concrete, or brick. Do not use on bare plaster. May be used as an enamel undercoater on wood surfaces where a latex undercoater is desired. Performance: - Primes and seals drywall and wallboard - Use under latex or oil/alkyd paints - Excellent hold-out - Prevents streaking and spotting of topcoats by sealing porous surfaces - Lays down nap of wallboard before application of alkyd topcoats - Fast drying - May be tinted - Soap and water cleanup Characteristics: Finish: Flat Colors: White Drying Time ( @ 77F & 50% R.H.): To Touch: 1 hour To Recoat: 3-4 hours Spreading Rate: 400 sq. ft. per gal. @ 4 mils wet, 1.2 mils dry Volume Solids: 30.3% Weight Solids: 42.8% Weight/Gal. : IO. 1 1 lbs. Vehicle Type: Vinyl Acrylic Latex Flash Point: 201F P.M. Closed Cup Tinting: up to 4 oz. per gal. with BLEND-A-COLOR or SPECTRAL Colorants. Surface Preparation: Surface must be smooth, clean and free of oil, dirt and dust. Unpainted Surfaces: On drywall patch cracks and holes with spackling paste. On wood fill nail holes and allow to dry. Masonry (brick, concrete, etc.) must be cured and dry. Previously Painted Surfaces: No primer is required if in sound condition and of uniform porosity. Dull glossy surfaces by sanding with fine sandpaper or steel wool or wash with an abrasive cleanser and rinse well. Patched and bare areas must be clean and spot-primed before painting entire surface. Application and Reduction: It is recommended that the primer be tinted to the approximate shade of the topcoat. Paint at temperatures above 50F. Roll or brush full body. For conventional spray reduce with up to 1/2 pint of water per gallon. For airless spray use full body.

Dutch Boy Paints

183

DUTCH BOY PAINTS: Professional Interior/Exterior Architectural Latex Block Filler: A high solids block filler or a 1 coat drywall texture finish. Typical Uses: Recommended for interior/exterior concrete block or cinder block. May be used as interior texture finish on wallboard or drywall. Not for use in showers, car washes or other high moisture areas. Performance: - Fills & seals block - Textures interior wallboard Use under latex or oil/alkyd paints - High build finish Characteristics: Finish: Flat Colors: ‘White Drying Time ( @ 77F & 50% R.H.): To Touch: 2 hours To Recoat: 18 hours To recoat with chemically resistant coatings such as epoxy: 48 hours. Spreading Rate: Block: 75-125 sq. ft. per gallon Drywall: 150-200 sq. ft. per gallon Volume Solids: 55.7% Weight Solids: 75.4% Weight/Gal. : 14.96 lb. Vehicle Type: Vinyl Acrylic Latex Flash Point: 201F P.M. Closed Cup Tinting: up to 4 oz. per gal. with BLEND-A-COLOR or SPECTRAL Colorants or 1 qt. per gallon of exterior or interior latex paint, depending on application.

-

Surface Preparation: Unpainted Surfaces: On block remove all foreign material. On wallboard latex block filler may be applied by brush, roller or spray. Previously Painted Surfaces: Remove all loose paint, foreign material, etc. Application and Reduction: Apply at 50F or above. Protect from freezing. May be used at full body for maximum filling efficiency. For conventional spray use De Vilbiss JGA-502 Gun, MBC 510 Gun, 326 Cap AS tip, 100 psi atomization pressure, 15-20 psi fluid pressure or equivalent spray equipment. For airless spray use .031 x 4 3 Tip, 30 mesh filter. Cleanup: Clean hands, tools and equipment with warm soapy water. This product meets all present lead hazard regulations.


DUTCH BOY PAINTS: RUST BEATER Interior/Exterior Oil/Alkyd Metal Primer: A fast drying rust inhibitative white primer. Typical Uses: Recommended for interior or exterior metal equipment, tools, trim, railings, furniture, etc. Use over any non-galvanized metal surface. Performance: - Excellent adhesion - Dries in 30 minutes - White color covers easily with topcoat - Use under latex, oil/alkyd or high performance coatings - Inhibits rust on iron & steel Durable enough for industrial applications Use as shop or field coat

-

Characteristics: Finish: Low Lustre Color: White Drying Time ( @ 77F

To Touch: 1/2 hour To Recoat: 1 /2 hour Spreading Rate: 200 sq. ft. per gallon at 8 mils wet 3 mils dry Volume Solids : 40.1 % Weight Solids: 62.4% Weight/Gal.: 11.47 lbs. Vehicle Type: Alkyd Flash Point: 87F P.M. Closed Cup &

50% R.H.):

Surface Preparation: Previously Painted Surfaces: Clean surface of all loose, peeling paint and foreign material If it is necessary to topcoat with a strong solvent topcoat, Oil/Alkyd Metal Primer may be used as a barrier coat. Unpainted Surfaces: Clean off all dirt, grease, oil and remove all rust. Spot prime all corners, crevices and other areas prone to rust. Application and Reduction: Do not apply at temperatures less than 40F. For brush application, use at full body. For conventional spray, reduce with up to one pint of Xylol per gallon of paint. For airless spray application, use at full body. Cleanup: Clean hands, tools and equipment with xylol or lacquer thinner.

Flame Control Coatings, Inc.

FLAME CONTROL COATINGS, INC.:

185

FLAME CONTROL No. 6 Clear Wood

Sealer: FLAME CONTROL No. 6 is a crystal clear, hard, wood sealer, developed primarily for use with FLAME CONTROL Fire Retardant Varnishes. Surface Preparation: Surfaces must be clean, dry and free from all loose or powdery materials, grease, wax or other foreign matter. All staining and filling must be done using non-bleeding type stains prior to the application of No. 6 Sealer. Application: (New work) Previously uncoated surfaces: Apply a full bodied coat by brush, at a coverage rate of 300450 square feet/US gallon (360-540 square feet/Imperial gallon). Coverage rate depends upon the porosity of the wood. Highly porous woods may require a second coat of No. 6 Sealer. (Old work) Previously coated surfaces: Previously varnished surfaces must be sanded to remove all gloss,. loose or poorly bonded varnish. Test patch a small area to determine the compatability of No. 6 Sealer with existing coating, to insure that no lifting or wrinkling occurs. If lifting or wrinkling develops, it is necessary to completely remove the old finish before proceeding. Coverage: 300-450 square feet/US gallon (360-540 square feet/Imperial gallon), depending on porosity of the wood. Thinners: For thinning and cleaning equipment, use only FLAME CONTROL No. 6 Reducer. Packaging: Standard packaging, 1 gallon, 5 gallon and 55 gallon containers

186 Prepaint J3Decialtiesand Surface Tolerant Coatings

FLAME CONTROL COATINGS, INC.:

FLAME CONTROL NO. 8 5 0 Series:

Air dry, no heat curing required High performance industrial heat resistant primer FLAME CONTROL No. 850 Series Industrial Heat Resistant Primer is based on a specially modified silicone-alkyd resin. The primer air dries to a tough, hard, weather, heat, and corrosion resistant finish. Special pigments are utilized to achieve maximum heat resistant properties. The curing mechanism is a unique combination of solvent evaporation and resin cross-linking. It does not require any complex heat-curing schedule to obtain heat, weather, and corrosion resistance. No. 850 Series Primer is suitable for use on stainless steel surfaces; it is formulated with special ingredients to minimize contamination from chlorides and other halides, sulfides, nitrates, and metals known to induce external stress corrosion cracking. It contains no metallic zinc and therefore, will not contribute to embrittlement of stainless steel welds. Recommended Uses: Wherever maximum resistance to heat, humidity, weather, and corrosion is required. Can be used on heaters, stacks, boilers, breeches, mufflers, radiators, storage tanks, pipelines, steam lines, etc., where operating temperatures will not exceed 850F (4540). Performance Information: This very unique primer (and topcoats) performs as well as many pure silicone based paints, but has the distinct advantage of being curable at room or ambient temperatures. It has exceptional heat resistant properties, excellent weathering characteristics, and corrosion resistance. Characteristics: Finish: Low gloss Resin Type: Modified silicone alkyd Type of Cure: Solvent evaporation/resin cross-linking Drying Time @ 77F (25C) & 50% R.H.: To touch: 1/2 hour To recoat: 2 hours Full cure: 72 hours Curing Temperature and Time: Minimum curing temperature: 50F (IOC) Minimum curing time: N.A. Application Temperature: 50F (IOC) to 180F (82C) Spreading Rate: Approximately 425 sq.ft./gal. (10.4 m2/L) 3.8 mils wet, 1.5 mils dry Coverage at 1 Mil Dry: Approximately 626 sq. ft./gal. Solids by Weight: 64.5%+2% Solids by Volume: 40.0%*2% Weight Per Gallon: 10.5 lbs. Flash Point of Liquid Coating: 80F (26.60) ReducerlCleaner: Xylol (Xylene) Application: Brush, roller, conventional and airless spray

Flame Control Coatings, Inc.

187

FLAME CONTROL COATINGS, INC.: FLAME CONTROL Special NonFlammable Paint Stripper No. 11: FLAME CONTROL No. 11 has been developed primarily for use in stripping old polyurethane and intumescent coating systems. The product contains no waxes, acids or alkalis. The material is fast acting and allows for quick and complete removal of old layers of urethane and intumescent paints. Direction for use: Brush apply FLAME CONTROL No. 1 1 to the surface to be stripped. Allow the material to penetrate for approximately 10 minutes, then using a plastic scraper (or other non abrasive type scrapers) and rags, scrape and wipe the old coating from the surface. Normally one application is sufficient, however, surfaces having an excessive film build up may require a second application of No. 11. Product Specifications: Flash Point T.C.C.: Non Inflammable Viscosity: Moderately Thixotropic Weight per Gallon: 9 . 3 Nominal Product Type: Emulsion-Water Soluble Active Ingredients: 100% FLAME-GLAZE 9922 Two Part Epoxy Primer: FLAME-GLAZE 9922 Two Part Metal Primer (Epoxy). This twopart epoxy primer is for use on steel, cast iron and treated aluminum under polyurethane coatings. It has a high degree of chemical and solvent resistance and should be used wherever maximum performance in extremely agressive environments is required. Surface Preparation: Surfaces must be free of grease and oil, mill scale, rust, moisture, and all other contamination. Blast cleaning is preferred. Mixing: For use of partial containers, mix in ratio of 5.5 to 1.0 by weight or 3.5 to 1.0 by volume. Application: Mixed material is suitable for brushing and rolling without reduction. For thinning, reduce with 50:50 xylene; methyl isobutyl ketone or equivalent. Top Coatings: Moisture curing polyurethane coating may be applied over the primer after overnight cure.


THE F W D CO.:

VIP TEX-POLYMER SEALANTS 65000 Series:

An emulsion type, internally plasticized, waterproof, terpolymer acrylic sealant. Basic Use: Expansion Joints Shrinkage Cracks Interior/Exterior Movement Cracks (non structural) Sealing and bedding shower stalls or sinks Plumbing & Electric intakes Bedding for cant strips flashing and reglets Sealing Window Frames, Skylights, etc. performance Information: Waterproof (above grade) Excellent flexibility--525% Elongation 5 year warranty (when used as part of VIP waterproof system) Superior adhesion Excellent weatherability Technical Data: Color: White, 4 package colors in cartridges Textures: Smooth and low Recommended Spread Rate: Coverage will vary due to nature of surface or use of product. Cartridge will seal 25 lineal ft. @ 1/4" x 114". Recommended Film Thickness: 5100 Buttering Grade--62 mils wet for seams and voids. Cure Time: 24 hours (temperature and humidity dependent) Volume Solids: 51 00--56%*2% 5300--Regular Grade--64%*2% 5500--Smooth Grade--68%*2% Applicable Standards: Meets Federal Specification TT-S-O0230C(2) By performance. Complies with all EPA and OSHA requirements for product. Meets CARB Regulations. Physical Properties: Elongation: 525% (ASTM D412-75) Adhesion: Glass to Aluminum 14 psi Aluminum to Aluminum 20 psi Concrete to Concrete > l o 0 psi Slump: 40F to 77F--None Hardness: 30 (Shore A) Extension/Compression: (Aluminum to Aluminum @ 77F) 40 cycles @ 25%--No failure, joint movement >12.5% 20 cycles @ 50%--No failure, joint movement >25%

The Flood Co.

THE FLOOD CO.:

189

VIP 1000 Waterborne Surface Conditioner:

A clear oil emulsion penetrating surface conditioner. It is designed to consolidate light to moderate chalk to the substrate allowing a subsequent coating of a non-penetrating coating to adhere properly. Basic Use: Concrete Dust Chalking Paint Soft or Porous Cement Brick stucco Concrete Block Poured & Precast Concrete Weathered Asbestos Technical Data: Color: Milky when wet--Clear when dry Dry Time: 24 Hrs. Recommended Spread Rate: 150-200 Sq. Ft./Gal. Depending on porosity of substrate Volume Solids: 35%*2% Applicable Standards: Complies with all EPA and OSHA requirements for the product Meets California VOC regulations. Surface Preparation: Masonry and concrete surfaces should be clean and free of oil and grease. Remove loose particles, laitance, efflorescence and other foreign materials by wire brushing or other effective means. Surfaces with a heavy chalk face should be power washed or sand blasted. Application: Always stir thoroughly. VIP 1000 Waterborne may be applied by brush, roller or spray. Low pressure spray systems should be used and care should be taken to assure 100% coverage of the surface. Coverage will vary depending on the porosity of the surface and the amount of chalk. The average coverage rate is 150-200 Sq.Ft./Gal. Equipment used to apply VIP 1000 Waterborne may be cleaned with soap and water. Limitations: VIP 1000 Waterborne is strictly a primer top coated within 7 days after application. the ambient or surface temperature is below relative humidity is in excess of 90%. Keep

and should be Do not apply when 40F. or when from freezing.


THE FLOOD CO.: VIP 1200 Acrylic Alkali Resistant Surface Conditioner:

A clear 1 0 0 % methacrylate resin emulsion type surface conditioner. It is designed to allow new above grade concrete or stucco to be coated prior to a 30 day cure. VIP 1200 is also a sealer designed to consolidate light chalk and concrete dust on the surface allowing a non-penetrating coating to adhere properly. Basic Use: New Concrete stucco Light Chalk Concrete Block Mortar Joints Concrete Dust Technical Data: Color: Clear Dry Time to Recoat: 1 hour min.--7 days max. Recommended Spread Rate: 200-300 square feet/gallon depending on substrate Volume, Solids: 20%*2% Applicable Standards: Complies with all EPA and OSHA requirements for the product Meets California VOC regulations. Surface Preparation: Masonry and concrete surfaces should be clean and free of oil and grease. Remove loose particles, laitance, efflorescence and other foreign materials by wire brushing or other effective means. Surfaces with a heavy chalk face should be power washed or sand blasted. Application: VIP 1200 may be applied by brush, roller or spray. pressure spray systems should be used and care should to assure 1 0 0 % coverage of the surface. Coverage will depending on the porosity of the surface. The average rate is 200-300 square feet/gallon. Equipment used to 1200 may be cleaned with water.

Low be taken vary coverage apply VIP

Limitations: VIP 1200 is strictly a primer and should be top coated within 7 days after application. Before application, allow stucco and mortar to cure three days and poured in place concrete to cure seven days. Do not apply when the ambient or surface temperature is below 40 degrees F. or when the relative humidity is in excess of 90%. Do not apply if rain is expected within 2-3 hours. Do not apply to surface with excessive moisture content. Keep from freezing. Moderate to heavy chalking surfaces are not suitable for the use of VIP 1200.

The Flood Co.

THE FLOOD CO.:

191

VIP 1600 Clear Asphalt Sealer:

An emulsion type acrylic clear co-polymer sealer. It is designed to assist in the sealing of asphalt surfaces prior to overcoating with VIP #5000 Series Sealants, #3500 and FOAMGUARD 4000 Roof Coatings. Basic Use: To provide an interface barrier between the asphalt substrate and the VIP Product during the cure phase of the coating. The coating will not be chemically changed while being applied, or during the period of curing. VIP #1600 also helps reduce "bleed through" during the cure time. Technical Data: Color: Clear Recommended Spread Rate: 200-300 sq.ft./gal. Drying Time: To touch 1 hr. To recoat - 4 hrs. Volume Solids: 46%+2%

-

Applicable Standards: Complies with all EPA and OSHA requirements for the product Meets California VOC regulations. Surface Preparation: The surface should be clean, free of dirt, chalk, dust, grease and other foreign matter. Application: By spray, roller or brush at a rate of 200-300 square feet per gallon. The product is not suitable for soft or semi-liquid underlayment. This product can usually be overcoated after four hours of drying time. Limitations: Surface and ambient temperatures must be between 50F. (1OC.) and llOF. (43.30). Relative humidity above 85% will retard curing and delay recoating time. Curing process will stop when relative humidity exceeds 908, curing will resume once the humidity level drops. Do not apply VIP #1600 if there is a threat of rain, or if rain is expected within 24 hours. Protect from freezing. Store between 5OF and 80F.


"FXE FLOOD CO.: Products: E-B EMULSA-BOND: Assures latex paint adhesion to chalky, dusty,surfaces-masonry--wood--weathered asbestos--aluminum siding Use with latex finishes including house paint, exterior stains, and masonry paints. Advantages of E-B EMULSA-BOND: 1 . Provides a bonding primer and a first coat of latex paint, both in the same application. 2. Dries quickly and can usually be recoated within four hours 3 . Maintains color. Bonding coat is same color as finish paint. 4 . Easy workability whether rolling, brushing or spraying. Minimizes misses and holidays resulting from roller skips. 5. Maximizes adhesion between primer and finish coats. Nothing sticks to latex like latex. 6. Provides a complete latex system with easy soap and water cleanup. PENETROL Aluminum: For specialized industrial use to fight rust/corrosion

- Provides low cost rust/corrosion protection for woven wire fencing, utility towers and light poles, plant ceilings, storage tanks, galvanized roofs and more. - Combines PENETROL benefits--rust penetration, deep penetration, toughness and lasting adhesion--with high quality alumimum pigment. - Spreads right over rusted steel fast, easily, under a wide range of temperature conditions. - Has no offensive fumes.

...

E.S.P.--EASY

SURFACE PREP:

Prepare smooth slick surfaces for painting or varnishing; i.e., old gloss enamel or varnish, glazed or ceramic tile, baked appliance enamel, lacquer, and glass. SEASONITE Stabilizing Treatment: For new pressure-treated wood

- Ideal for new pressure-treated decks and patio lumber; cedar and redwood; wood siding; fences; cedar shakes and shingles; and unfinshed outdoor furniture. - Can be applied before or after lumber is installed. - Provides a slow, steady seasoning process to reduce warping, cupping and swelling. - Provides a sound surface for painting, staining or finishing - Produces a film that resists mildew. - Economical and easy to apply with brush, roller or sprayer.

The Glidden Co.

TEE GLIDDEN CO.:

193

GLIDDEN Protective Maintenance Coatings:

Alkyd Finishes: Alkyd coatings are the most widely used finishes in the industrial maintenance market. Although limited in chemical resistance, they produce good weathering and application ease. Their low initial installation cost makes them an excellent choice for mild interior and exterior atmospheric conditions. They are extremely well suited for painting mildly corrosive environments when the main reason for repainting is aesthetic. Alkyds resist humidity and rain well. However, they are not suitable for immersion, heavy chemical fumes, acids, and alkali solutions. Alkyds are formulated with a variety of ingredients, controlled to give desired sheen, flexibility and chalk and performance under specific conditions. GLID-GUARD: SPEEDENAMEL Q.D. Enamel, No. 4300 Series SPEEDENAMEL Q.D. (Quick Dry) is designed for finishing a wide variety of metal products, both ferrous and aluminum. Fast air dry and baking schedules permit quick handling, packing or assembly of finished parts. Excellent durability and gloss retention. Technical Data: Color--White, Ready-Mixes, & Many Tints Recommended Film Thickness--1.5 mils dry Solids by Volume--36.3% Coverage at Recommended Film Thickness--388 sq.ft./gal. Theoretical Coverage ( 1 mil D.F.T.)--582 sq.ft./gal. Recoat Time--4 hrs. (Handle--30 min.) Dry Heat Resistance--200F. Reduction Solvent--Xylene GLID-GUARD: Alkyd Industrial Enamel, No. 4550 Series An exceptionally durable interiorlexterior alkyd gloss enamel for general maintenance painting and new construction. Provides maximum protection in type "M"--moderate atmospheres. Available in a wide variety of colors including OSHA accepted safety colors. Can be brushed, rolled, or sprayed on any type of surface which has been properly primed. Technical Data: Color--White, Ready-Mixes & Many Tints Recommended Film Thickness--2.0 mils dry Solids by Volume--43.9% Coverage at Recommended Film Thickness--350 sq.ft./gal. Reduction Solvent--Brush/Roll: Mineral Spirits Spray: VM&P Naphtha Drying Time--Touch: 1 hr.; Recoat: 16 hrs. Sheen--High Gloss 85 min. @ 60 Dry Service Temperature--200F (Color change likely)

1 9 4 Prepaint Specialties and Surface Tolerant Coatings

THE GLIDDEN CO.: (Continued):

GLIDDEN Protective Maintenance Coatings

GLID-GUARD: Alkyd Industrial Enamel, No. 4550 Series(C0ntinued): Advantages: - Lead Free - Excellent Weathering Good Adhesion - Good Color Retention - Excellent Chalk Resistance

-

Typical Usage: - Water Storage Tanks - Grain Elevators Pipes Dado Walls - Exterior Metal (Buildings)

-

GLID-GUARD: Alkyd Tank

&

Structural Enamel, No. 5220 Series

An extremely durable, highly adherent, long oil alkyd gloss enamel. The long oil alkyd resin provides a flexible finish with lasting elasticity minimizing the possibility for failure when subjected to severe thermal shock. Excellent resistance to mild chemical fumes and abrasion. Superior gloss and color retention. Can be applied by brush, roll or spray. An excellent finish for steel tanks, bridges, prefabricated steel storage buildings, or any large metal surface. Available in a full range of colors. Technical Data: Color--Aluminum, White & Full Color Range Recommended Film Thickness--4.0 mils dry Solids by Volume--50.2% Coverage at Recommended Film Thickness--200 sq.ft./gal. Reduction Solvent--Brush/Roll: Mineral Spirits Spray: VM&P Naphtha Drying Time--Touch: 3-5 hrs.; Recoat: 1 6 - 2 4 hrs. Sheen--Gloss 70 @ 60 Dry Service Temperature--200F (Color may change) Advantages: Lead Free - Medium Dry - Film Flexibility Gloss/Color Retention - High Film Build Typical Usage: - Grain Storage Bins - Water Towers - Bridges

-

-

-

Structural Steel Train Cars

The Glidden Co.


195


Alkyd Finishes(C0ntinued): ULTRA-HIDE: Alkyd Spray Enamels, Dry Fog, Nos. 5067, 1180, 1185 ULTRA-HIDE Spray Enamels, flat and eggshell are high-hiding durable enamels for use in industrial, commercial and instititutional buildings. They hide and cover most surfaces in a single coat, are non-yellowing, fume resistant and resist dirt pick-up. The "dry fog" characteristics of these products minimize cover-up and clean-up expense. Advantages : - Dry Fog Overspray Sweeps Up In Minutes - Covers in One Coat - Fume and Discoloration Resistant - Creates Bright, Clean, Working Environment Typical Usage: - Ceilings of Manufacturing Plants Hotels, Offices, Warehouses - Canopies - Above Plant Dado Lines

-

Technical Data: Color--White Recommended F lm Thickness-- 5067: 1.5 mils dry) (1180: 2 mils drv) 1185: 1.5 mils dry ) Solids by colume--(5067: 37. % ) (1180: 49.4%) (1 85: 47.1%) Coverage at Recommended D.F. .--400 sq.ft./gal. Reduction Solvent--Brush/Rol : Mineral Spirits Spray: VM&P Naphtha Drvins - - Time--Touch: 30 min.; Recoat: 6 hrs. (1185: 2 hrs.) Sheen--(5067: 3 @ 60) (1180: 5 @ 60) (1185: 20-25 @ 60) Dry Service Temperature--200F Other Alkyd Finishes: SPRED ULTRA Alkyd Semi-Gloss Enamel No. 4200 Series: A premium quality interior semi-gloss enamel for walls, ceilings, trim and protected exterior surfaces. This durable, low odor enamel is sag resistant and clings to sharp edges. SPRED LUSTRE Alkyd Semi-Gloss Enamel, No. 4600 Series: A heavy-duty, high quality interior semi-gloss enamel designed for use on all types of wall, ceiling and trim surfaces. Sag resistant, clings to sharp edges. Low odor solvents permit use in occupied structures. May be used on protected exterior surfaces.

196


THE GLIDDEN

CO.:


(Continued): Alkyd Finishes(C0ntinued): ULTRA-HIDE Alkyd Enamels, No. 5 0 8 6 / 5 4 5 0 / 5 7 0 0 / 5 9 5 0 : These are high-hiding, low odor interior enamels in flat, eggshell and semi-gloss finishes. Available in a wide range of colors ideally suited for churches, schools and plant offices. Washable, and excellent hiding. ULTRA-HIDE Alkyd Gloss SANI-GIENE Enamel, No. 5069: A mildew resistant gloss enamel treated with fungicide to protect the paint itself from growth of mildew. USDA approval for incidental food contact makes it the ideal product for interior walls and ceilings of bakeries, dairies, and breweries. Available in white. Coal Tar: Coal Tar Systems have been proven over time to withstand mild acid and alkaline chemicals. Both Coal Tar Epoxies and Coal Tar Solutions stay flexible and exhibit excellent adherence to steel and concrete surfaces. These are commonly used products for tank and pipe coatings. GLID-GUARD: Coal Tar Emulsion, No. 6 1 7 8 0 A heavy-duty nonflammable emulsion coating primarily used over coal tar solvent cutbacks for protection against sunlight. An extremely flexible flat black coating which can be directly applied to all surfaces above grade. Do not use for immersion service. Advantages: Resists Sunlight Cracking Flexible - Excellent Weathering Properties Can Be Applied Over Almost Any Primer Typical Usage: Protective Topcoat Over Other Coal Tar Products Pipe Coating Above Grade Pulp and Paper Mills - Refineries Technical Data: Color--Black Recommended Film Thickness--12.5 mils dry Solids by Volume--42.0% Coverage at Recommended Film Thickness--53 sq.ft./gal. Reduction Solvent--Brush/Roll: Water Spray: Water Drying Time--30 min.; Recoat: 1 - 2 hrs. Sheen--Flat Dry Service Temperature--200F.

-

The Glidden Co.


197


Coal Tar(Continued): GLID-GUARD: Top Service Thick Black, No. 61778 A heavy-duty coal tar product for concrete and metal immersion service in standard waste and nonpotable water. Reinforced with silicone resin and pigment, it resists moisture, mineral acids, alkalies, and most corrosive materials. When exposed above grade, should be topcoated with Coal Tar Emulsion No. 61780 to resist cracking. Do not use for potable water service. Advantages: - Flexible - Thick Film in One Coat - Meets MI1 18480e Typical Usage: - Sewage Treatment Plants Concrete Columns Piers - Caissons Technical Data: Color--Black Recommended Film Thickness--6.0 mils dry Solids by Volume--62.0% Coverage at Recommended Film Thickness--165 sq.ft./gal. Reduction Solvent--Brush/Roll: 61884/85 Spray: 61 884/85 Drying Time--Touch: 2-4 hrs.; Recoat: 6-12 hrs. Sheen--Semi-Gloss 60 @ 60 Dry Service Temperatufe--150F. GLID-GUARD: T&O Solution Tank Black, No. 61774 A fast-drying, solvent-based coal tar product. A self-priming and extremely water resistant finish which can be used on potable water tanks; will not impart taste. Advantages: - Quick Drying - Self-priming High Build - Can Be Used On Potable Water Tanks Typical Usage: - Water Softeners Cold Water Tanks - Air Conditioners - Chillers Technical Data: Color--Black Recommended Film Thickness--2.0 mils dry Solids by Volume--60.0% Coverage at Recommended Film Thickness--384 sq.ft./gal. Reduction Solvent--Brush/Roll: Xylene Spray: Xylene Drying Time--Touch: 2 hrs.; Recoat: 4 hrs.; Service: 48 hrs. Sheen--Semi-Gloss 60 13 60 Dry Service Temperature--200F

-

-

-

198 Prepaint Sgecialties and Surface Tolerant Coatings



Coal Tar(Continued): GLID-GUARD: Black Solution, No. 61776 A solvent based coal tar pitch well suited as a general maintenance coal tar primer or finish. A paint-like consistency makes it ideally suited as first coat on masonry and steel under TOP SERVICE THICK BLACK. Do not use for potable water service. Advantages: Quick Drying - May Be Spray Applied - LOW cost

-

Typical Usage: - Primer Under Other Coal Tars - Small Parts Coating Technical Data: Color--Black Recommended Film Thickness--2.0 mils dry Solids by Volume--60.0% Coverage at Recommended Film Thickness--480 sq.ft./gal. Reduction Solvent--Brush/Roll: 61864/65 Spray: 61864/65 Drying Time--Touch: 1 hr.; Recoat: 4 hrs.; Service: 24 hrs. Sheen--Semi-Gloss 60 @ 60 Dry Service Temperature--200F. GLID-GUARD: Hi-Build Coal Tar Epoxy Finish No. 5273/5274

A two component, self-priming, chemically cured coal tar polyamide-epoxy coating. The two components are formulated so that they may be mixed in equal volumes prior to application. For use on metal and concrete, interior or exterior surfaces, abave or below ground, and in immersion service. For use in highly corrosive environments. This product has wide usage in water and sewage treatment plants. Do not use for potable water service. Advantages: - Self-priming - Corrosion Resistant - Components Can Be Mixed in Equal Volume Prior to Application Typical Usage: - Water Plants - Sewage Treatment Facilities

The Glidden Go.



Coal Tar(Continued1: GLID-GUARD: Hi-Build Coal Tar Epoxy Finish No. 5273/5274(Continued): Technical Data: Color--Black Recommended Film Thickness--14.0-20.0 mils dry Solids by Volume--75.0% Coverage at Recommended Film Thickness--85 sq.ft./gal. Reduction Solvent--Xylene Drying Time--Touch: 3 hrs.; Recoat: 5-20 hrs.; Full Cure 72 hrs. @ 77F.; 5 days @ 60F. Sheen--60 @ 60% Dry Service Temperature--25OF. GLID-GUARD: Coal Tar Epoxy Finish, No. 527015271 A rugged industrial coating resistant to chemicals, water, abrasion and corrosion. A combination of coal tar epoxy resin base and a polyamide converter. An excellent coating for immersion surfaces of waste and non-potable water or many chemical storage areas. Provides an extremely high film build in a single coat. Do not use for potable water service.

Advantages: - High Film Build - Corrosion Resistant - Self-priming Water Resistant

-

Typical Usage: - Interior Metal Tanks - Sewage Treatment Facilities Silos - Pits

-

Technical Data: Color--Black Recommended Film Thickness--8.0 mils dry Solids by Volume--75.0% Coverage at Recommended Film Thickness--150 sq.ft./gal. Reduction Solvent--Brush/Roll: Xylene Spray: Xylene Drying Time--Touch: 3 hrs.; Recoat: 5-20 hrs.; Full Cure: 5 days Sheen--Semi-Gloss 60 @ 60 Dry Service Temperature--200F.

199




Epoxy : Epoxy coatings are comprised of two package components. A chemical reaction of the two components takes place at above 55F. Since most epoxies have a limited pot life after mixing, the curing agent must be packaged separately. The three basic types of epoxies are amine, polyamide and polyester. While all three have a broad range of chemical resistance, the amine types have the most durability in a highly corrosive chemical atmosphere. The polyamides, however, have a greater water resistance and tolerance to poor surface preparation. These two types have good film integrity on weathering but exhibit chalking and yellowing in exterior exposures. The polyester epoxy combines excellent resistance to chalking and discoloration on exteriors but is not as chemical resistant and moisture resistant as amines or polyamides. Polyester epoxy also has better non-yellowing properties than amine or polyamide types on interior exposure. Epoxy systems, properly selected to match the environment, are a widely accepted finish in corosive atmospheres. GLID-GUARD GLID-TILE: Epoxide Coating, No. 5550 Series A high-in-solids two component polyester epoxy for all interior or exterior surfaces. Excellent exterior weathering resistance, exceptional stain resistance and mild chemical resistance. High film thickness gives a "tile-like'' appearance on porous masonry surfaces. Meets all requirements for air pollution under Rule 66. Do not use for immersion service or as a floor coating. Advantages: - High Build - Abrasion Resistance Low Odor - Chemical Resistance Typical Usage: - Hospital Walls - School Walls - Animal Pen Walls - Laboratories Technical Data: Color--White and Colors Recommended Film Thickness--6.0 mils dry Solids by Volume--62.1% Coverage at Recommended Film Thickness--165 sq.ft./gal. Reduction Solvent--(if needed)Brush/Roll: 5568 Spray: 5568 Drying Time--Touch: 6 hrs.; Recoat: 16 hrs.; Full Cure: 5 days Sheen--Semi or Full Gloss Dry Service Temperature--200F.

-

The Glidden Co.

THE GLIDDEN CO.:

201


(Continued): Epoxy(Continued): GLID-GUARD: Epoxy Chemical Resistant Finish, No. 5240 Series These chemical, moisture, and abrasion resistant products are based on polyamide resins. Epoxy Chemical Resistant Finishes give positive and maximum protection to galvanized iron, steel, aluminum, masonry and some plastics against most common corrosive chemicals and atmospheric conditions. They are highly resistant to the deteriorating effects of many acids, alkalies, solvents, greases, oils and other active chemicals. Like most epoxy coatings, GLID-GUARD Epoxy Chemical Resistant Finishes characteristically lose gloss and chalk on exposure to direct sunlight; however, they maintain excellent film integrity. Their superior flexibility and toughness, plus resistance to thermal shock, make them ideal for large surface areas such as storage tanks, walls, floors, machinery and equipment in the food processing and chemical industries, petroleum refineries, paper mills, marine structures and general industrial buildings. These standard GLID-GUARD Epoxy Chemical Resistant Finishes can be converted to double build systems of 5 mils dry film thickness by using GLID-GUARD Double Build Epoxy Chemical Resistant Curing Agent No. 5452. This Double Build Converter can also be used with GLID-GUARD Epoxy Safety Colors and GLID-GUARD Double Build Epoxy Chemical Resistant Primer Base No. 5461. The GLID-GUARD Epoxy Chemical Resistant Finish No. 5555 High-Build Gray/No. 5556 High-Build Curing Agent is a low gloss epoxy polyamide coating designed for use as an intermediate coat in highbuild GLID-GUARD Epoxy Chemical Resistant Systems. It is formulated to provide 5 mils of dry film thickness in one coat, used over GLID-GUARD Epoxy Primers to provide needed protection in problematical industrial environments. However, No. 5555/ 5556 may be used as a top coat where sheen and color are satisfactory. Note: No. 5555 Finish Coat and No. 5556 Curing Agent cannot be mixed with any other finish coats or curing agents--they can only be used together. Technical Data: Color--White, Colors and Clear Recommended Film Thickness--3.0 mils Solids by Volume--45.7% Standard Coverage at Recommended Film Thickness--244 sq.ft./gal. Reduction Solvent--Brush/Roll: 5568 Epoxy Solvent Spray: 5568 Epoxy Solvent Drying Time--Touch: 4 hrs.; Recoat: 5 hrs. Full Cure: 7 days Sheen--Semi to Full Gloss 65 Minimum @ 60 Dry Service Temperature--25OF.

202 Prepaint s;Oecialtiesand Surface Tolerant Coatings



GLID-GUARD: Epoxy Chemical Resistant Finish, No. 5240 Series(C0ntinued): Advantages: - Excellent Solvent Resistance - Excellent Alkali Resistance - Maximum Hardness Accepted For Immersion in Fresh and Salt Water - Long Flexibility To Resist Aging 5250 and 5266 Only Accepted By FDA For Food Contact and Potable Water Service - Accepted By USDA For Incidental Food Contact

-

Typical Usage: Chemical Storage Tanks - Petroleum Refineries - Paper Mills - Dairies Meat Packing Plants

-

GLID-GUARD: High Solids Epoxy, No. 5430 Series A polyamide cured epoxy coating for use on interior and exterior metal, masonry and wood surfaces where a highly protective finish is desired. This product combines high volume solids with a tough film highly resistant to many alkalis, acids, solvents, greases, oils and other active chemicals, and provides excellent substrate protection in chemical and atmospheric environments. May be used as a self-priming system on many properly prepared ferrous metal surfaces. Available in a wide range of tinted colors plus white. Like most epoxy coatings, this product will lose gloss and chalk on exposure to direct sunlight, but will maintain excellent film integrity and provide excellent protection to the substrate. Technical Data: Color--White and Full Range of Colors by Tinting Recommended Film Thickness--4.0 mils (minimum) Solids by Volume--65.9% Coverage at Recommended Film Thickness--264 sq.ft./gal. Reduction Solvent--Xylene Drying Time--Handle: 8-5 hrs.; Recoat: 6 hrs. Dry Heat Resistance--25OF.

The Glidden Co.


203


GLID-GUARD: Hiqh Solids Epoxy, - - . No. 5430 Series(C0ntinued) Advantages : - High Film Build Excellent Abrasion Resistance--Hard, Tough Film - Excellent Alkali and Solvent Resistance - Protection Against Immersion in Fresh and Salt Water - Free of Toxic Amine Curing Agents Simplified 1 to 1 Mixing Ratio - Surface and Atmospheric Moisture Tolerance During Application Wide Color Selection From Deep, Bright Accents and Safety Colors to Pastel Shades - No Induction Normally Required Typical Usage: Storage Tanks Structural Steel Piping Walls Machinery and Equipment Petroleum Refineries Paper Mills Chemical Plants Marine Structures General Industrial Buildings GLID-GUARD: Epoxy Surfacing Compound, No. 5561 An exceptionally durable, 100 percent solids epoxy amine material with aggregate fortification. Apply as a topping on new concrete or when patching old concrete. A special aggregate provides impact and chemical resistance far beyond that of regular concrete or many sand fortified patching materials. Generally applied by trowel. Do not use for potable water service. Technical Data: Color--Gray Recommended Film Thickness--As Required Solids by Volume--100% Coverage at Recommended Film Thickness--As Required Reduction Solvent--None Required Drying Time--Touch: 4 hrs.; Recoat: 5 hrs.; Full Cure: 4 days Sheen--Flat Dry Service Temperature--250F. Advantages: - Adheres Well to Existing Concrete - Eight Times Stronger Than Concrete - Resists Spalling and Erosion - Bound Firmly By Epoxy Resins - Outstanding Chemical Resistance Typical Usage: - Loading Docks - Walkways in Plants - Support Base for Tanks Airport Runways

-

-

-

204 Prepaint Specialtits and Surface Tolerant Coatings



Epoxy(Continued): GLID-GUARD: Epoxy Self-priming Mastic, No. 525615257 A gray corrosion, chemical, water and abrasion resistant coating. An extremely high build finish based on an amine adduct curing agent. A tough, thick and flexible coating that may be top coated with polyamide epoxy for increased color and gloss retention. Do not use for potable water service. Technical Data: Color--Gray Recommended Film Thickness per coat--7.0 mils dry Solids by Volume--44.7% Coverage at Recommended Film Thickness--102 sq.ft./gal. Reduction Solvent--None Required Clean-up Solvent--5568 Drying Time--Touch: 1 hr.; Recoat: 5 hrs.; Full Cure: 5 days Sheen--Flat 1 0 @ 60 Dry Service Temperature--25OF. Advantages: - Flexible To Resist Aging - High Film Build - Resists Fresh and Salt Water - Excellent Resistance to Many Chemicals, Alkalies, Solvents Typical Usage: - Chemical Processing Plants - Mining Industry Oil Storage Tanks Drainage Pipes and Canals - Beverage Industry

-

GLID-GUARD METALLITE: High Build Epoxy NO. 547515476 A two component high solids, high build epoxy-polyamide. A self-priming coating with excellent adhesion over both wire-brushed and sandblasted rusted steel. Provides very good general chemical and water resistance. Do not use for potable water service. Technical Data: Color--Aluminum Recommended Film Thickness--5.0 mils dry Solids by Volume--81.0% Coverage at Recommended Film Thickness--260 sq.ft./gal. Reduction Solvent--Xylene Drying Time--Handle 16 hrs.; Recoat: 16 hrs. Sheen--Metallic Dry Service Temperature--25OF.

The Glidden Co.


205


Chemical Cleaning Restoration Products: Chemical cleaning with Glidden's ULTRA-KLEAN line of products provides users with the capability to remove all kinds of surface dirt, such as atmospheric grime, pollutants and damaging paint build-ups, while it leaves the original surface intact. These Glidden products were specifically formulated for each phase of cleaning and restoration projects. Special materials are available to match every type of exterior building surface, including brick, sandstone, terra cotta, limestone, wood, and painted wood and masonry. ULTRA-KLEEN Heavy-Duty Paint Stripper & Graffiti Remover (Spray Grade) No. 20512: A thixotropic, solvent/alkaline compound designed specifically for removing multiple layers of paint and graffiti from porous masonry surfaces. Formulated as a "slow working" paint stripper, the product remains active for up to 24 hours, allowing deep penetration through multiple layers of paint and complete removal of paint resins and pigments. One application will remove up to 12 coats of paint from porous brick, concrete and stone surfaces. When product is used properly, painted masonry can be restored to its original attractive appearance. ULTRA-KLEAN Fast Acting Paint Stripper(Graffiti Remover) No. 20527: A thixotropic, solvent-base paint remover formulated to remove graffiti, paint (non-cementitious) and clear coatings Designed for use with high pressure rinsing equipment. Fast Acting Paint Stripper is immediately emulsifiable in water, providing easy rinsing with cold water, hot water or steam. This product contains strong, highly penetrating solvent ingredients. Formulated for removing high strength paints and coatings such as epoxies, urethanes and floor enamels. ULTRA-KLEAN Regular Water Repellent No. 20532: A general purpose, non-silicone water repellent for waterproofing of vertical, above-grade masonry surfaces. It penetrates deeply into the surface to provide long-lasting waterproofing protection to dense clay brick, architectural concrete and natural stone surfaces. This "breathing type" water repellency allows vapor transmission through the treated surface to reduce spalling and cracking. Properly applied, it forms a highly effective surface and subsurface waterproofing barrier against moisture migration from exterior to interior surfaces. It also reduces weathering streaks and color changes caused by penetration of waterborne discolorants. Provides no aesthetic change in the appearance of the masonry, however, because of the wide variatuion in the types of masonry, a slight darkening may be noticed on some surfaces.

206 Prepaint Qxxialties and Surface Tolerant Coatings

THE GLIDDEN

CO.:

Primers for ~ y p s u mBoard/Plaster Surfaces:

SPRED ULTRA: Latex Primer-Sealer 5 1 1 1 A premium quality, fast-drying interior primer designed to provide maximum uniformity and sealing properties to wall surfaces such as gypsum drywall, plaster, masonry and previously painted surfaces. May be recoated the same day with alkyd enamels and latex paints. Technical Data: Color: White Volume Solids: 3 4 . 9 % Recommended Film Thickness: 1 . 4 mils dry Theoretical Coverage ( 1 mil D.F.T.): 5 6 0 sq ft /gal Recoat Time: 4 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water SPRED SATIN: Primer-Sealer 341 6 A superior interior latex primer-sealer for use on extremely porous surfaces. A quick-dry, high pigmented sealer accepting a wide range of topcoats.

Technical Data: Color: White Volume Solids: 3 4 . 6 % Recommended Film Thickness: 1 . 4 mils dry Theoretical Coverage ( 1 mil D.F.T.): 5 0 2 sq.ft./gal. Recoat Time: 3-4 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water ULTRA-HIDE: PVA Primer-Sealer 5019 A latex primer formulated with special polyvinyl acetateacrylic resins and high-hiding pigments to provide a fast drying primer with excellent sealing and covering properties. May be recoated the same day with alkyd enamels or latex paints.

Technical Data: Color: White Volume Solids: 2 5 . 8 % Recommended Film Thickness: 1 . 1 mils dry Theoretical Coverage ( 1 mil D.F.T.): 4 1 0 sq.ft./gal. Recoat Time: 2 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water

The Glidden Go.

207

THE GLIDDEN CO.: Primers for Gypsum BoardIPlaster Surfaces (Continued): INSUL-AID: Vapor Barrier Primer-Sealer 5 1 1 6 A special latex primer-sealer for interior walls and ceilings. It reduces loss of interior moisture through walls to help maintain insulation efficiency and guard against paint adhesion failures. Meets FHA (HUD) Minimum Property Standards M 613-2 Walls and M 613-3 Ceilings, which specify a perm rating of 1 . 0 . INSUL-AID has a rating of just 0 . 6 . Technical Data: Color: White Volume Solids: 34.6% Recommended Film Thickness: 1 . 4 mils dry Theoretical Coverage ( 1 mil D.F.T.): 5 0 2 sq.ft./gal. Recoat Time: 3-4 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water Primers for Wood Surfaces: GLIDDEN : Oil Wood Undercoater 310 An oil interior undercoater with excellent sealing properties. May be top coated with either alkyd or latex finishes. Dries overnight for easy sanding. Can also be applied to properly prepared metal (except galvanized) in Type P environments only. Technical Data: Color: White Volume Solids: 5 0 . 3 % Recommended Film Thickness: 1.5 mils dry Theoretical Coverage ( 1 mil D.F.T.): 807 sq.ft./gal. Recoat Time: 1 6 hrs. Dry Heat Resistance: n/a Reduction Solvent: Mineral spirits for Brush & Roll; VM&P Naphtha for Spray GLIDDEN : Prime Coat--Oil/Alkyd Base 3651 Modified alkyd primer for priming and sealing exterior unpainted wood and previously painted stucco, masonry, asbestos shingles and aluminum siding. Excellent primer for exterior hardboard. May be top coated with oil or latex based finishes. Technical Data: Color: White Volume Solids: 59.3% Recommended Film Thickness: 2.1 mils dry 951 sq.ft./gal. Theoretical Coverage ( 1 mil D.F.T.): Recoat Time: 24 hrs. Dry Heat Resistance: n/a Reduction Solvent: Mineral Spirits: Brush & Roll; VM&P Naphtha: Spray

208 Prepaint Sppecialties and Surface Tolerant Coatings

THE GLIDDEN CO.: Primers for wood Surfaces(Continued): GLIDDEN Prime Coat: Latex Base 3690 An acrylic latex primecoat for use under either alkyd, oil base or latex base house paints. Suitable for use over new wood or repaint surfaces. Ideal for use over plywood, white and yellow pine. Technical Data: Color: White Volume Solids: 30.0% Recommended Film Thickness: 1.2 mils dry Theoretical Coverage ( I mil D.F.T.): 482 sq.ft./gal. Recoat Time: 2-6 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water Other Primers: ULTRA-HIDE: Wallcovering Primer-Sealer 64897 An oil base formulation especially designed for use on porous surfaces to prepare walls for wall-covering. Technical Data: Color: White Volume Solids: 36.8% Recommended Film Thickness: 1 .I-1.5 mils dry Theoretical Coverage ( 1 mil D.F.T.): 590 sq.ft./gal. Recoat Time: 2-4 hrs. Dry Heat Resistance: n/a Reduction Solvent: VM&P Naphtha or Mineral Spirits ULTRA-HIDE: Wallcovering Primer-Bond 64900 A high quality latex primer for application of wallcovering over glass, ceramic tile or glossy painted surfaces. Also used to install new vinyl wallcoverings over existing vinyl wallcoverings.

Technical Data: Color: White (Dries Clear) Volume Solids: 32.0% Recommended Film Thickness: 6 mils wet Theoretical Coverage (1 mil D.F.T.): 513 sq.ft./gal. Recoat Time: 15-30 mins. Dry Heat Resistance: n/a Reduction Solvent: Water

The Glidden Co.

THE GLIDDEN CO.:

Primers for MasonryfConcrete and Block/Cement

Surfaces: GLID-GUARD: Alkali Resistant Primer 5212 A solvent-reduced synthetic rubber base white primer formulated for interior and exterior masonry surfaces such as stucco, tile, brick, plaster, concrete and non-friable cementasbestos. Because of its exceptional resistance to alkalies, No. 5212 is an ideal primer for "problem" areas. It will prevent most alkali reactions that cause paint failure. This primer has a high tolerance for moisture usually encountered in the Food Processing Industry, making it excellent for use in bottling plants, dairies, breweries and food processing plants. Accepted by USDA for incidental food contact areas. Technical Data: Color: White Volume Solids: 32.5% Recommended Film Thickness: 1 . 6 mils dry Theoretical Coverage ( 1 mil D.F.T.): 5 2 2 sq.ft./gal Recoat Time: 4 hrs. Dry Heat Resistsnce: n/a Reduction Solvent: Xylene ULTRA-HIDE: Acrylic Latex Block Filler 5 3 1 7 A ready-mixed interior-exterior block filler designed to accept a wide variety of topcoats including epoxies. Fills most voids and pores in masonry with minimum pinholing. Dries quickly, may be top coated in four hours (under normal conditions). Technical Data: Color: White Volume Solids: 47.8% Recommended Film Thickness: Varies 7 6 8 sq.ft./gal. Theoretical Coverage ( 1 mil D.F.T.): When computing working coverage, allow for application losses, surface irregularities, etc. Recoat Time: 4 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water

209

210


THE GLIDDEN CO.: Primers for Masonry/Concrete and Block/Cement Surfaces(Continued): ULTRA-HIDE: Latex Interior Block Filler 5320 High production interior masonry block filler designed for airless spray application. May also be brushed or rolled. Accepts a wide variety of topcoats. Dries to recoat in four hours under normal conditions. Technical Data: Color: White Volume Solids: 36.8% Recommended Film Thickness: Varies Theoretical Coverage (1 mil D.F.T.): 120 sq.ft./gal. When computing working coverage, allow for application losses, surface iregularities, etc. Recoat Time: 4 hrs. Dry Heat Resistance: n/a Reduction Solvent: Water GLID-GUARD: GLID-TILE Epoxide Basecoat 5512 Top-of-the-line ready-mixed block filler designed for highperformance architectural coatings. "Locks" to concrete to become an integral part of the system. Used especially for maximum "tile like" appearance under epoxy topcoats. Highly resistant to hydrostatic pressure. Technical Data: Color: White Volume Solids: 64.8% Recommended Film Thickness: n/a Theoretical Coverage (1 mil D.F.T.): 75 sq.ft./gal. When computing working coverage, allow for application losses, surface irregularities, etc. Recoat Time: 16 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Water

The Glidden Co.

21 1

THE GLIDDEN CO.: Primers for Metal Surfaces: GLID-GUARD RUSTMASTER: Alkyd Metal Primer 590 A high quality, rust inhibitive metal primer for structural steel and general maintenance use. Formulated without lead or chromate pigments. May be used under all oil, alkyd or latex top coats. Do not use on galvanized metal. For interior/exterior metal in Type P and M environments only. Technical Data: Color: White Volume Solids: 52.8% Recommended Film Thickness: 2.0 mils dry Theoretical Coverage (1 mil D.F.T.): 846 sq.ft./gal. Recoat Time: 16 hrs. Dry Heat Resistance: 200F. Reduction Solvent: VM&P Naphtha or Mineral Spirits Will accept DRAMATONE Tinting Colorants up to 2 ozs/gal. GLID-GUARD: Universal Fast Dry Metal Primer 5210 A fast dry, tung-oil modified alkyd primer to be used as a barrier coat over old oil or alkyd finishes to be overcoated with heavy duty maintenance coatings such as epoxy, vinyl and chlorinated rubber. Use under or over most coatings on structural steel, tank exteriors, piping and pipe racks, etc. Do not use on galvanized metal. For interior/exterior metal in Type P & M environments only. Technical Data: Color: Red Volume Solids: 35.3% Recommended Film Thickness: 1.5 mils dry Theoretical Coverage (1 mil D.F.T.): 566 sq.ft./gal. Recoat Time: 2 hrs. Dry Heat Resistance: 200F. Reduction Solvent: VM&P Naphtha or Xylene for spray; Xylene for Brush & Roll


THE GLIDDEN CO.:

Primers for Metal Surfaces(Continued):

GLID-GUARD: Epoxy Chromate Metal Primer 5251/5252 A polyamide converted epoxy with good rust inhibitive and chemical resistant properties. Provides excellent adhesion both to the surface and to successive coatings. Unique formulation displaces moisture when applied to.damp surfaces and is tolerant of marginal surace preparation. An outstanding primer for all galvanized metal, aluminum and steel. For interior/exterior use. Do not use for potable water or other fresh water immersion service. Technical Data: Color: Green Volume Solids: 35.1% Recommended Film Thickness: 1.5 mils dry Theoretical Coverage (1 mil D.F.T.): 563 sq.ft./gal. Recoat Time: 3-4 hrs. Dry Heat Resistance: 250F. Reduction Solvent: GLID-GUARD Epoxy Solvent 5568 GLID-GUARD: Alkyd Metal Primer 4570 Excellent corrosion resistant primer for all structural steel and general maintenance use. Lead free formulation exhibits good adhesion even where surface preparation is marginal. May be used under all oil, alkyd or latex top coats. Do not use on galvanized metal. For interior/exterior ferrous metal in Type P and M environments only. Technical Data: Color: Oxide Red Volume Solids: 44.9% Recommended Film Thickness: 2.0 mils dry Theoretical Coverage (1 mil D.F.T.): 721 sq.ft./gal. Recoat Time: 16 hrs. Dry Heat Resistance: 200F. Reduction Solvent: VM&P Naphtha or Mineral Spirits

The Glidden Co.

THE GLIDDEN CO.:

213

Primers for Metal Surfaces(C0ntinued):

GLID-GUARD: Metal Shop Primer, Fast Dry 5209 A low cost, fast dry shop primer. Withstands exterior exposure six months without topcoating. It may be used under epoxies, vinyls and chlorinated rubber as well as conventional alkyd and latex finishes. Do not use on galvanized metal. For interior/ exterior ferrous metal in Type P & M environments only. Technical Data: Color: Oxide Red Volume Solids: 24.3% Recommended Film Thickness: 1.0 mils dry Theoretical Coverage (1 mil D.F.T.): 391 sq.ft./gal. Recoat Time: 1-2 hrs. Dry Heat Resistance: 200F. Reduction Solvent: VM&P Naphtha or Xylene GLID-GUARD: Tank & Structural Metal Primer 5205 A fast-drying, rust-inhibitive metal primer which may be topcoated with epoxy, urethane, vinyl and other heavy-duty maintenance coatings as well as conventional alkyd and latex coatings. Suitable for shop or field application. Not for use on galvanized metal. Ideal for the steel fabrication industry and structural steel in all industries. Exhibits excellent exterior durability and corrosion resistance. Technical Data: Color: Oxide Red Volume Solids: 49.9% Recommended Film Thickness: 2.0 mils dry Theoretical Coverage ( 1 mil D.F.T.): 801 sq.ft./gal. Recoat Time: 2 hrs. (Dry to touch in 20 min.) Reduction Solvent: Xylene GLID-GUARD: All-Purpose Metal Primer 5229 An adherent and elastic primer providing protection to galvanized metal and aluminum. Adhesion actually improves with age. For use under all alkyd, oil and latex finishes. Excellent as a one coat finish on new interior metal decking, joists, ceiling structural steel and masonry. Interior/exterior--galvanized and aluminum. To be used in Type P & M environments only. Technical Data: Color: White Volume Solids: 50.7% Recommended Film Thickness: 1.5 mils dry Theoretical Coverage (1 mil D.F T. ) : 81 4. Sq. ft. /gal. Recoat Time: 24 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Mineral Spir ts or VM&P Naphtha

214


THE GLIDDEN CO.:


GLID-GUARD VINYL-COTE: Primer 5521 Specifically developed to provide an all-vinyl coatings system for maximum protection of steel surfaces in chemical environments. Especially resistant to splash, spillage and/or fumes of inorganic acids and excellent for water immersion. Provides excellent adhesion and allows fast recoating. Frequently used as a tie coat for overcoating inorganic zincs. For interior/exterior metal. Technical Data: Color: Gray Volume Solids: 20.4% Recommended Film Thickness: 2.0 mils dry Theoretical Coverage (1 mil D.F.T.): 327 sq.ft./gal. Recoat Time: 2 hrs. Dry Heat Resistance: 150F. Reduction Solvent: GLID-GUARD Vinyl Chloride Reducer 5519 GLID-GUARD: Epoxy Chemical-Resistant Double Build Primer 5461/5452 Red This rust inhibitive, chemical resistant primer is a polyamide converted epoxy designed for steel requiring an epoxy finishing system. It is highly penetrating and exhibits excellent adhesion. It is used on storage tanks, structural steel and equipment in petroleum plants, chemical plants, refineries, pulp and paper mills as well as marine and general industrial use. It will tolerate some surface moisture during application and may be used on galvanized metal or in immersion service. For interior/exterior metal. Do not use for potable water service. Technical Data: Color: Red Volume Solids: 44.5% # Recommended Film # 5452 Converter Thickness: 5 mils dry Theoretical Coverage (1 mil D.F.T.): 714 sq.ft./gal. Recoat Time: 4-6 hrs. Dry Heat Resistance: 250F. Reduction Solvent: GLID-GUARD Epoxy Solvent 5568 # Will build 3 mils dry when converter 5242 is used.

The Glidden Co. 215

THE GLIDDEN CO.:


GLID-GUARD: Speedenamel Q.D. Primer 4397 A fast-drying alkyd primer ideal for spot priming when quick topcoating is required. For use under all oil, alkyd or latex top coats. Do not use on galvanized metal. For interiorlexterior metal and spot priming exterior siding in Type P & M environments only. Technical Data: Color: White Volume Solids: 39.4% Recommended Film Thickness: 1.5 mils dry 632 sq.ft./gal. Theoretical Coverage (1 mil D.F.T.): Recoat Time: 1-2 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Xylene Will accept DRAMATONE Tinting Colorants up to 4 ozs./gal. GLID-GUARD: METALLITE High Build Aluminum Epoxy 5475/5476 This high solids epoxy-polyamide self-priming coating exhibits excellent adhesion over both wire brushed and sandblasted rusted steel. Provides very good general chemical and water resistance. Recommended uses include interior/exterior structural steel, tanks, metal buildings, piping, equipment and highway bridges. Technical Data: Color: Gray Aluminum Volume Solids: 81 %22% Recommended Film Thickness: 5.0 mils dry min., 12.0 mils dry max. 1300 sq. ft./gal. Theoretical Coverage ( 1 mil D.F.T.): Recoat Time: 16 hrs. Dry Heat Resistance: 250 Continuous Reduction Solvent: Xylene GLID-GUARD: Red Lead Metal Primer 5532 A high quality rust inhibitive metal primer for equipment, tanks, piping and structural steel. It will tolerate light surface rust and still provide good adhesion. Can be used under all alkyd, oil and latex top coats. Do not use on galvanized metal. For interior/exterior steel in Type P & M environments only. Technical Data: Color: Orange Volume Solids: 49.3% Recommended Film Thickness: 1.6 mils dry Theoretical Coverage (1 mil D.F.T.): 791 sq.ft./gal. Recoat Time: 8 hrs. Dry Heat Resistance: 200F Reduction Solvent: Mineral Spirits

216

Prepaint Spoecialties and Surface Tolerant Coatings

THE GLIDDEN CO.:


GLID-GUARD: Zinc Chromate Primer 5533 A high solids, fast drying, corrosion resistant metal primer. High quality primer can be used on all steel under oil, alkyd or latex top coats. Do not use on galvanized metal. A good production primer and shop coat. For interior/exterior ferrous metal in Type P 8 M environments only.

Technical Data: Color: Red Volume Solids: 52.32% Recommended Film Thickness: 1.2 mils dry Theoretical Coverage (1 mil D.F.T.): 839 sq.ft./gal. Recoat Time: 8 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Xylene RUSTMASTER PRO: Primer 5571 A waterborne vinyl primer which provides exceptional protection against atmospheric corrosion when applied to structural steel, tank exteriors, and other ferrous metal surfaces in architectural, industrial, or marine (onshore or offshore) environments. This product is non-combustible, has a very low volatile organic compounds content, and is formulated without lead or chromium pigments--features which make it particularly suitable for use where maximum safety and minimum solvent emission levels are of concern.

Technical Data: Color: Oxide Red Volume Solids: 39.7% Volatile Organic Compounds: - 0 1 per gal. Recommended Film Thickness: 3.5-4.0 mils Theoretical Coverage ( I mil D.F.T.): 637 sq.ft./gal. Recoat Time: 3-4 hrs. Dry Heat Resistance: 15OF. Reduction Solvent: Water

The Glidden Co.

THE GLIDDEN CO.:

2 17


GLID-THANE ONE: Primer 6120 A single package moisture-cured urethane primer developed for use under the GLID-THANE ONE Finish System. This primer will adhere well to tightly bonded rust and to other old generic coatings that have been cleaned prior to application. This coating may be applied over a clean dry surface at temperatures as low as 10F. Do not use in immersion service. A good primer for weathered galvanized metal. Technical Data: Color: Silver Metallic Volume Solids: 56.0% Recommended Film Thickness: 1.5-2.0 mils dry Theoretical Coverage ( 1 mil D.F.T.): 898 sq.ft./gal. Recoat Time: 2-4 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Xylene or Toluene GLID-GUARD: LIFEMASTER I1 Water Reducible Acrylic Metal Primer 6970 Specially formulated as the first coat in Glidden's LIFEMASTER 11 system, this water reducible metal primer provides a firm foundation for quick topcoating with a LIFEMASTER I1 finish. This system offers the user excellent exterior durability, toughness and flexibility. Ideal for use on interior and exterior surfaces of service stations and other commercial structures. Also well suited for use in industrial plants, on storage tanks, structural steel and other properly prepared metal surfaces. Not recommended for application to galvanized metal. Technical Data: Color: Red Volume Solids: 39.9% Recommended Film Thickness: 4.0 mils dry in two coats Theoretical Coverage ( 1 mil D.F.T.): 640 sq.ft./gal. Recoat Time: 24 hrs. Dry Heat Resistance: 200F. Reduction Solvent: Water


THE GLIDDEN CO.:


GLID-GUARD: Chlorinated Rubber Primer 5502 Formulated to provide rust inhibitive and chemical resistant properties. This red oxide primer is intended for use on new ferrous metal surfaces where previous coatings have been completely removed. When properly topcoated with the entire chlorinated rubber system, this finish gives excellent protection to metal and masonry surfaces because of its impermeability and resistance to corrosive attack from acid and alkali solutions and their fumes. Resistant to oxidizing agents, bleaches and cleaning compounds to help maintain the appearance of structures and equipment where cleanliness is of prime importance. For interior and exterior metal. Do not use for potable water service. Technical Data: Color: Red Volume Solids: 31 .OS Recommended Film Thickness: 1.5-2.0 mils dry 497 sq.ft./gal. Theoretical Coverage (1 mil D.F.T.): Recoat Time: 45 mins. Dry Heat Resistance: 150F. Reduction Solvent: Xylene GLID-GUARD: Vinyl Chloride Metal Conditioning Primer 5290 A corrosion-inhibiting surface treatment for use with GLIDGUARD Vinyl Chloride Finishing Systems. It properly conditions clean metal surfaces such as steel, galvanized iron, aluminum, copper, etc. for receiving subsequent coats of GLID-GUARD Vinyl Chloride Finish. It may also be used to provide immediate protection to freshly sand-blasted surfaces and additional corrosion resistance to surfaces mentioned above when finish coats other than vinyl chloride finishes are to be used. This product is a phosphoric acid "wash" treatment material, not a true primer. Do not use for potable water service. Technical Data: Color: Green Volume Solids: 8.9% Recommended Film Thickness: 0 . 3 mils dry Theoretical Coverage (1 mil D.F.T.): 142 sq.ft./gal. Recoat Time: 30 mins. Dry Heat Resistance: 150F. Reduction Solvent: No. 5293 Vinyl Chloride Finish Metal Conditioning Primer Reducer

Insl-X Products Cow.

INSL-X PRODUCTS CORP.:

219

CHECKRUST Chemical Resistant Primers:

MP-0915 SPEEDY METAL PRIMER (Red): Lead-Free Chromate Free A red oxide metal primer that dries in 15 minutes and can be recoated in 50 minutes. Apply with brush, spray or roller. Reduce with TH-0200 to spray, TH-0201 to brush or roll.

-

MP-0911 SPEEDY METAL PRIMER (Light Gray): Lead Free - Chromate Free Same vehicle and qualities as MP-0915. Dries in 15 minutes; recoat in 50 minutes. Excellent for top-coating with white and pastel colors. MP-0969 FISH OIL PRIMER (Red): Lead Free - Meets New Low VOC Requirements Can be brushed, rolled or sprayed over exterior damp, rusty, painted or bare metal surfaces. Allow 24 hours to dry before recoating. UNIVERSAL Primers Series: MP-9000 (Gray-Green): MP-9010 (Oyster White):# MP-9015 (Red Oxide) :# # Lead Free -- # Chromate Free High performance, rust inhibitive primers for use under most topcoats, including: two component urethanes, epoxies, lacquers as well as most other oleoresinous systems. All can be used as a tiecoat over existing paint in sound conditions. MP-9091 Heavy Duty, Hi Performance, Fabrication Primer (Light Gray) : - Lead Free - Chromate Free - Meets New Low VOC Requirements High solids, low VOC primer that inhibits rust. Penetrates cracks around light rust and mill scale. Protects corners and edges. Resists exposure to weather. Excellent for priming steel framing to be fire-proofed. MP-9095 Heavy Duty, Hi Performance Fabrication Primer (Red Oxide) : Meets New Low VOC Requirements Contains Red Iron Oxide and Zinc Chromate. High solids low VOC primer that inhibits rust. Penetrates cracks around light rust and mill scale. Protects corners and edges. Resists exposure to weather. Excellent for priming steel framing to be fire-proofed.



CHECKRUST Chemical Resistant Primers:

INSL-TILE EPOXY Primers: EP-5050 (Red): EP-5065 (Light Gray): Lead Free

-

Chromate Free

-

USDA Authorized

Two component 1.1 ratio polyamide cured primers for use on clean or pretreated metal surfaces. Excellent resistance to corrosion and exceptional adhesion to ferrous surfaces. Provides an excellent base for the application of chemical resistant coatings such as epoxies and urethanes. ZR-1650 ZINC-X (Gray): USDA Authorized - 93% Zinc

-

Matte Gray

A ready mixed, organic coating that renews worn or damaged galvanic metals. Use it to prime or prime & finish. Apply by brush, spray or roller. Dries to touch in 30 minutes; topcoat in 4 hours. Reaches maximum hardness in 48 hours. Reduce with TH-0206 to spray; TH-0208 to brush or roll. Meets MIL P-21035. ZR-3650 Inorganic Zinc (Green Gray): A self-curing, single package inorganic zinc-rich coating that is hard, abrasion resistant and provides cathodic protection similar to galvanizing. Recommended as a single coat for marine, coastal and heavy industrial environments and for surfaces exposed to heat. In corrosive chemical exposure or more severe coastal or heavy industrial environments, appropriate topcoats should be used.

ZR-5650 Zinc-Rich Epoxy (Green Gray): A single component, high molecular weight epoxy resin designed to be used on sandblasted steel. May be top-coated with two conventional epoxies, two component urethanes and conventional coating systems.

SC-4411 Shopcoat Primer (Light Gray): Lead Free Low lustre primer designed f o r use as a shopcoat primer for structural or architectural steel. Has good wetting properties providing penetration and bonding for power or hand tool cleaned surfaces. For use in mild to moderate atmospheric services. Dries rapidly and is adaptable for production line coating applications.

h i - X Products Gorp. 221

INSL-X PRODUCTS CORP.: (Continued):

CAECKRUST Chemical Resistant Primers

SC-4415 Shopcoat Primer (Red): Lead Free Same vehicles and qualities as SC-4411. WC-P100 Vinyl Wash Primer (Light Green): A two component pretreatment for metals, giving excellent adhesion to steel, stainless steel, tin, aluminum and other metal substrates. When properly applied, gives an excellent surface for all subsequent coatings, regardless of their generic nature. Meets performance requirements of Federal Specification MIL P-15328. WP-PBlO Water Reducible, High Performance Primer (Off White): Lead Free - Chromate Free - Meets New Low VOC Requirements A new generation acrylic emulsion that has outstanding adhesion to aluminum, galvanized metal, wood, plaster, and formica. It eliminates flash rusting or rust bleed through. USDA authorization pending.

GA-2310 GALVIN-X: Lead Free - Meets New Low VOC Requirements A water base, semi-gloss coating that adheres directly to most new, unpainted or partially rusted galvanized metal and other slick metal surfaces without etching or acid treatment. Apply by brush, spray or roller. Dries in 1 hour, recoat in 4 hours. May be tinted with most universal colorants.

RA-0104 RUST ARRESTOR: A water reducible, clear coating that chemically converts tightly adhered rust, stopping the corrosion mechanism, sealing the substrate, and presenting a surface that can be successfully topcoated with conventional or exotic finish systems.

222

Prepaint aecialties and Surface Tolerant Coatings


CHECKRUST F i n i s h Coats:

IE-0200 INSTANT ENAMEL

-

15 Minute Dry:

A high-gloss enamel that dries in 15 minutes; can be recoated in two hours if desired. No primer is needed on clean metal. Apply by brush, spray or roller. Excellent durability on exterior and interior metal, wood and masonry. Reduce with TH-0200 to spray; TH-0201 to brush or roll. Lead Free: - IE-0200 - IE-0210 - IE-0220 - IE-0225 IE-0236

-

-

IE-0241

Clear Appliance White Black Terra Cotta Eye Rest Vista Green International Blue

Contains Lead: IE-0201 Int'l Red - IE-0215 Int'l Orange

-

Tint Bases

-

--

IE-0266 IE-0277

-

IE-0251 IE-0252

-

IE-0221

IE-0231 IE-0261 IE-0285

Machine Tool Gr. Machine Tool Lt. Gray John Deere Green Almond Walnut Brown

Caterpillar Yellow

May be tinted with CHROMA CHEM 844 Industrial Colorants: Tint Base Deep Base

-

Massey Harris Red Barber Green

-

IE-0290

Neutral Base

Lead Free:

-

IE-0203

-

IE-0232

IM-1000 INSTANT METAL COAT Lead Free

-

IE-0222

John Deere Yellow

15 Minute Dry:

A semi-gloss coating that primes and finishes in one application. Can be applied by brush, spray or roller over damp, rusty, painted or bare surfaces such as ornamental iron. For interior or exterior use. Can be recoated in 2 hours, if desired. Reduce with TH-0201 to brush or roll; TH-0200 to spray.

-

-

IM-1010 IM-1011 IM-1013 IM-1015 IM-1019

White Light Gray Battleship Gray Bridge Red Bronzetone

-

IM-1020 IM-1030 IM-1040 IM-1060

Black Semi-Gloss Wrt. Iron Flat Black Zinc Chr. Yellow Stainless Steel

lnsl-X Products Corp. 223


CHECXRUST Finish Coats (Continued):

SA-2700 Safety Enamel: A 30 minute dry, high gloss enamel conforming to U.S. Government regulations and ANSI specifications. For exterior or interior use to identify pipes, floors and equipment. Apply by brush, spray or roller. Recoat in one hour. Lead Free: SA-2703 - SA-2710

-

Safety Purple Safety White

Contains Lead: - SA-2702 Fire Protection Red - SA-2712 Danger Orange

-

SA-2720 SA-2742

Striping Black Warning Blue

-

SA-2723 SA-2737

Caution Yellow Safety Green

RB-1600 Chlorinated Rubber Base Enamel: INSL-X Chlorinated Rubber Base Enamel is a decorative chemically resistant coating. Excellent for use as a general purpose coating in marine exposures and service areas where corrosive conditions are present.

-

RB-1610

-

White

RB-1620

Black

Tint Bases--May be tinted with CHROMA CHEM 844 Industrial Colorants.

-

RB-1670 RB-1685

Tint Base Deep Base PRIMERS

-

RB-1690

- SEALERS -

Neutral Base

STAINKILLERS:

-

Stainkiller: IL-6600 INSL-LAC Primer - Sealer White Pigmented - Alcohol Thinned Primer - Sealer Stainkiller

-

Excellent for fire jobs. Seals water stains and eliminates smoke odors. Apply by brush, spray or roller. Dries in 15 minutes. Recoat in 2 hours with lacquers, vinyls, rubber base or standard paints. Reduce with TH-0300 Thinner.

PS-5500 Primer - Sealer USDA Authorized

-

Stainkiller (White):

Retards bleeding of most stains. Dries in 30 minutes. Recoat in 55 minutes with exterior or interior latex, oil or alkyd house paints, enamels or flat finishes. Apply with brush, spray or roller. May be tinted with most universal colorants.

224


INSL-X PRODUCTS CORP.: (Continued):

Primers

-

Sealers

-

Stainkillers

AQ-0500 AQUALOCK Water Based Primer: Sealer - Stainkiller (White) - USDA Authorized A new generation acrylic emulsion paint with outstanding sealing, stain killing and rust prevention characteristics. Excellent adhesion to interior or exterior surfaces, previously painted or new work. It may be sanded ana recoated in 60 minutes with exterior or interior latex, oil or alkyd house paints, enamels or flat finishes. Eliminates the odor of solvents and conforms to E.P.A. regulations. Can also be used for industrial applications as a metal primer where most solvent primers have been used.

Electrostatic Coatings: EQ-D400 ELECTROKOTE Quick Dry Enamel: A quick drying alkyd base subdued gloss one package enamel especially formulated for electrostatic spray application. Dries to handle in 1 5 minutes and may be put back into service in 2 hours.

-

EQ-D410

White

- EQ-D420

Black


-

-

EQ-D466 EQ-D477

Tint Base Deep Base

-

EQ-D490

Neutral Base

EE-6000 ELECTROKOTE Epoxy Enamel: A High Performance two-component polyamide epoxy, especially formulated for electrostatic spray application. It is ideal for use on metal, wood, concrete, fiberglass and many plastic surfaces.

-

EE-6010

White

-

EE-6020

Black


-

EE-6070 EE-6085

Tint Base Deep Base

-

EE-6090

Neutral Base

Insl-X Products Corp.


225

Epoxy Coatings:

EP-5000 INSL-TILE Epoxy Coating: Lead Free USDA Authorized

-

A high-gloss activated Polyamide cured, equal mix Epoxy. Can be applied by spray, roller or brush. Packed in kits containing equal-volume units of pigment and activator (Component "A") and epoxy resin (EP-GO01, Component "B" Gloss). Reduce with TH-0250 Epoxy Reducer. Finish Coats: EP-5000 Clear EP-5001 Red EP-5010 Appliance White EP-5020 Black EP-5036 Eye Rest Green EP-5037 Soft Green EP-5041 Dark Blue

EP-5042 EP-5054 EP-5055 EP-5061 EP-5062 EP-5066 EP-5087

Light Blue Pearl Gray Battleship Gray Beige Ivory Walnut Brown Sandstone

Tint Bases: May be tinted with CHROMA CHEM 844 Industrial Colorants. EP-5070 EP-5085

Tint Base Deep Base

EP-5090

Neutral Base

EP-GOO2 Comp B Hi-Build EP-SO01 Comp B Semi-Gloss EP-5100 INSL-TILE Clear Epoxy Penetrating Sealer: An equal mix Epoxy clear, penetrating sealer designed and recommended for use as a chemically resistant penetrating sealer for concrete or other cementitious surfaces. CT-EO20 Coal Tar Epoxy: A 2-component, heavy bodied polyamide cured polyamide Coal Tar Epoxy coating. Highly resistant to chemicals and corrosion. Ideal for use for the protection of metal and masonry surfaces. Meets Army Corps of Engineers C200 specification. CS-4675 Epoxy Clear Concrete Sealer: Stops dust on concrete floors of factories, food storage plants, etc. Dries overnight. For interior or exterior use. Brush, roller or squeegee application. Reduce with TH-0200 Reducer.



Epoxy Coatings(Continued):

AT-0100 AQUA-TILE Water-Base Epoxy Coating Lead Free:

A new generation, water-based catalyzed epoxy which gives performance equal to solvent based systems. Low odor, non-toxic. Class "A" fire rated, nonflammable. Excellent floor coating. Won't lift existing coating. USDA authorization pending. AT-B1 01 AT-B1 1 0 AT-B1 1 1

AT-Bl12 A T - ~ 1 13

Clear## White# Paste##

Tint## Deep##

# AT-All0 White Component A comes in kit with AT-B110 White Component B. # # AT-AlOO Mixing Base for Colors Component A comes in kit with the following Component B's: AT-Bl11 Pastel, AT-B112 Tint, AT-B113 Deep, AT-BlO1 Clear. To be tinted with Universal Colorants.

Food and Beverage Industry Coatings: FK-1310 FREEZERKOTE: USDA Authorized White

-

-

Lead Free

A High Gloss Coating for sub-freezing painting ( - 4 0 Degrees F to + 4 0 Degrees F). No residual odor to affect persons or perishable commodities. Ideal for maintenance of interior frozen food lockers, deep freeze units and other cold storage facilities without loss of operation time. Apply by brush, roller or spray. Dries in 1 hour. Reduces with TH-0300 FREEZERKOTE Reducer.

SE-0410 SUPER DAMPWALL Gloss Enamel: USDA Authorized - Fungus Resistant A high-build, high gloss, non-yellowing, white coating for use on damp interior walls and ceilings of dairies, bottling plants, breweries, restaurants, etc. Odorless, non-toxic, fungus resistant. Can be applied by brush, roller or spray. Dries in 5 hours. Reduce with TH-0202 Odorless Reducer. May be tinted with most universal colorants.

DU-1810 DAMPWALL UNDERCOATER: USDA Authorized - Fungus Resistant A flat, non-yellowing, white, primer-undercoater for use on damp, interior walls and ceilings of dairies, bottling plants, breweries, restaurants, etc. Can be applied by brush, roller or spray. Dries in 5 hours. Reduce with TH-0202 Odorless Reducer. May be tinted with universal colorants.



Heat Resistant Coatings:

AL-1000 INSLUME Aluminum: Lead Free A permanent chrome-like bright sheen for wood, metal and masonry. Dries in 1 hour. Primes and finishes in one application. For exterior or interior use, heat resistant up to 800 degrees F. Can be applied by brush or spray. AL-2402 Heat Resistant-Brilliant Aluminum: Lead Free Formulated to withstand temperatures from 500F to 1200F. Silicone resin base. For exterior or interior use on smokestacks, furnaces, boiler fronts, breeching, etc. Rust controlled; no primer needed. Dries in 1/2 to 1 hour; recoat in 24 hours. Apply by brush, spray or roller; reduce with TH-208 to brush or roll; TH-0206 to spray. HR-2413 Heat Resistant-Zinc Dust (Med. Gray): Matte finish, high temperature coating. Designed to be used over sandblasted steel. HR-2420 Heat Resistant (Flat Black): Lead Free High heat (1000 degrees F) resistant silicone coating ideal for exterior or interior grills, hoods, fireplaces, furnaces, boilers, heaters, stoves, etc. Ready to use. Dries to touch in 2 hours; recoat overnight. Reduce with TH-0201 to brush; TH-0200 to spray. HR-0820 Heat Resistant (High Gloss Black): Lead Free A rust-controlled coating resistant to temperatures of 1 5 0 degrees F to 450 degrees F. Ideal for exterior or interior smokestacks, silos, incinerators, etc. No primer needed. Apply by brush, spray or roller. Dries in 4 hours; recoat in 8 hours. Reduce with TH-0201 to brush; TH-0200 to spray. Heat Resistant Silicone Acrylics: HR-2410 (White): HR-2451 (Gray): Lead Free A superior combination of silicone and acrylic resins that provide a decorative enamel finish with excellent long term durability and heat resistance. Designed for use with surface temperatures from ambient to 450F for continuous service. Recommended for plants with problem areas where hot surfaces are exposed to corrosive environments, as well as home use for radiators and other hot surfaces. Excellent exterior durability, color and gloss retention. Dry time 15 minutes to handle, 8 hours to full hardness.

228



Industrial Colorants:

CC-8400 CHROMA-CHEM 844 Industrial Colorants: Simple, trouble-free tinting with the INSL-X tint program. Same fine performance characteristics as factory produced colors. Hundreds of customer colors available in:

-

-

INSL-TILE Epoxy Coating (EP-5000 Series) INSL-THANE Polyurethane Enamel (GU-2500 Series) Instant Enamel (IE-0200) INSL-TRON Acrylic Aliphatic Polyurethane Enamel (AU-0300) ELECTROKOTE Epoxy Enamel (EE-6000 Series) ELECTROKOTE Quick Dry Epoxy Enamel (EQ-D400) Chlorinated Rubber Base Enamel (RB-1600 Series)

QUARTS 844 0061 White 844-0451 Quina. Red 844-0962 Moly Orange# 844-0982 L/F Orange 844-1061 Red Iron Ox. 844-1352 Burnt Umber 844-1861 Yel. Iron Ox. 844-2061 Yellow Med.# 844-2555 L/F Med. Yel. 844-2851 Lt. Organic Yellow 844-2852 Organic Yellow 844-5558 Phthalo Green 844-7262 Phthalo Blue 844-9451 Quin. Violet 844-9955 Lampblack # Contains Lead

-

Code

m

QR MO u/o RO BU YO CY MY PY OY PG PB QV LB

Reducers f o r INSL-X Coatings: TH-0200 TH-0201 TH-0202 TH-0206 TH-0208

Spraying Reducer: Brushing Reducer: Odorless Reducer: Rubber Base Spraying Reducer: Rubber Base Brushing Reducer:

TH-0300 FREEZERKOTE Reducer: TH-0250 Epoxy Reducer: TH-0003 INSL-TRON Reducer: TH-6000 Electrostatic Reducer: EE-6000 Electrostatic Reducer is formulated to allow as much reduction as necessary to achieve the proper spray viscosity for the Electrostatic unit being used without adversely affecting the conductivity of the paint. The product can also be used for flushing the spray lines and general clean-up.


INSL-x PRODUCTS CORP.:

Polyurethane Coatings:

GU-2500 INSL-THANE Heavy Duty Polyurethane Enamel: USDA Authorized - Lead Free A high solids multipurpose enamel that provides an ideal protective coating for wood, metal or masonry surfaces which are subjected to frequent hard use. Excellent for use in homes and industry as well as boats and other marine uses.

-

-

GU-2501 GU-2503 GU-2509 GU-2510 GU-2511 GU-2512 GU-2513

Almond Dunes Tan White Semi Gloss White Light Gray Rustic Brown Dark Gray

-

GU-2515 GU-2519 GU-2520 GU-2521 GU-2529 GU-2530 GU-2514

Tile Red Bronzetone Black Black Semi Gloss Bronzetone Satin Flat Black Sandstone


-

GU-2560 GU-2577 GU-2590 GU-2570

Tint Base Deep Base Neutral Base Semi-Gloss Tint Base

-

GU-2587 GU-2599

Semi-Gloss Deep Base Semi-Gloss Neutral Base

-

GU-2504 GU-2518 GU-2536

Light Yellow Forest Green Vista Green

-

GU-2537 GU-2541 GU-2542

Safety Green Royal Blue Safety Blue

GU-2502 GU-2522

Safety Red Safety Orange

GU-2523 GU-2524

Safety Yellow School Bus Yellow

-

UC-2500 Clear High Gloss Polyurethane: UC-2555 Clear Satin Polyurethane: Lead Free Ideal for exterior-interior use. All wood floors, gymnasium floors, boats, redwood or cypress, bar tops, trim, paneling, and other areas subject to heavy use and traffic. Unexcelled for abrasion, stain, mar and water resistance. Protects metal and concrete. Apply by brush or roller. Dries in 1-2 hours; recoat in 24 hours.



Polyurethane Coatings(C0ntinued):

GX-2900 GRIP-X Anti-Skid Polyurethane Floor Enamel: Lead Free A high gloss, permanent abrasive floor coating designed to reduce accidents in slippery areas. Apply by brush or roller. Finish Coats: - GX-2911 GX-2912 - GX-2913

-

Light Gray Walnut Brown Battleship Gray

-

GX-2915 GX-2918

Tile Red Club Green

AU-0300 INSL-TRON High Performance, 2 Component Polyurethane: Acrylic Aliphatic Polyurethane Enamel - Lead Free INSL-TRON is a two-component acrylic aliphatic polyurethane consisting of a pigmented enamel. Component "A" and activator AC-O030--Component "B". It is an extremely durable finish having outstanding gloss and color retention. INSL-TRON is highly resistant to fumes, alkalis and acids. Its chemical resistance is unequaled. Tint Bases--May be tinted with CHROMA CHEM 844 Industrial Colorants.

-

AU-0366 AU-0377 AU-0390 AU-0376

Tint Base Deep Base Neutral Base Semi-Gloss Tint Base

-

AU-0387 AU-0399

Semi-Gloss Deep Base Semi-Gloss Neutral Base

AC-0030 Activator: AC-0070 INSL-TRON Accelerator: A special additive for INSL-TRON which speeds up the drying time when taping for two-tone work as well as minimizes dust and dirt contamination. Do not exceed 2 ounces per gallon. AF-4900 INSL-TUFF Polyurethane Floor & Deck Enamel: A tough, durable, glossy finish for interior and exterior wood, metal or concrete floors, decks, porches and trim.

-

-

AF-4917 AF-4930 AF-4934 AF-4936

Black Battleship Gray Sand Beige

-

AF-4910

White

-

AF-4932

Bright Red

-

AF-4938 AF-4940 AF-4946 AF-4948

Light Gray Pewter Gray Tile Red Dark Brown

AF-4942

Green

lntex Chemical, Inc.

INTEX CHEMICAL, INC.:

231

Metal Cleaners:

INTEX 8661 Hot Tank Ferrous: A granular alkaline hot vat cleaner to be used in food processing, as well as metal finishing processing. Properties: Color: White Powder Odor: Mild pH: 1% solution--13.0-13.5 Foaming: Low Rinsing: Free and Complete Hard Water Stability: Up to 500 ppm Biodegradable: Yes Using Conc.: Hot Tank: 1:15 to 1:20 (6 to 8 02. 8661 to each gallon of water.) Minimum Operating Temperature: 180F. Maximum Operating Temperature: 212F. Rust Removal: 1:15-1:20 (6 to 8 02. 8661 to each gallon of water. ) Safety on Materials: Safe on ferrous metals only. Approvals: USDA Class A-2. For use in federally inspected meat and poultry plants. Titration: Alkaline Test Kit--Factor 0.18 INTEX 8665 Electro Cleaner: A granular alkaline electrolytic cleaner designed for cleaning ferrous metals either by direct or reverse current. Properties: Color: White powder Odor: Irritating pH: 1 % solution--1 2.5-1 3.0 Foaming: Very low Rinsing: Free and complete Hard Water Stability: Up to 5 0 0 ppm Biodegradable: Yes Using Conc.: Tank Application: 1:20 (6 ounces 8665 to each gallon of water.) Steam Cleaning Brass Cleaning - 1:25 (5 ounces 8665 to each gallon of water.) Temperature Bath: 180F. or higher. Safety on Materials: Safe on ferrous metals, brass. Approvals: Specification PC-535-1 Titration: Alkaline Test Kit - Factor 0.19

-



Paint Removers:

INTEX 8561 Paint Remover: A thick phenolic solvent type paint remover developed to be applied by the flow on method. Effective on almost all modern finishes such as epoxies, polyurethanes, acrylics, and other chemical resistant paints. Properties: Form: Liquid Appearance: Light yellow Odor: Solvent pH: 9.0-9.5 (Conc.) Rinsing: Moderate Lbs./Gal.: 10.0 Use Conc.: Use as received. Do not dilute. Apply with a brush, spray nozzle, etc. Allow to set until paint blisters, then flush with a high pressure water rinse. Operating Temperatures: Minimum Operating--Ambient Maximum Operating--90F Process Hints: A) To insure clean surface, follow with water rinse. B) Be sure stripping action complete before rinsing. Titration: None Approvals: Douglas CSD-1 Safety on Materials: Non corrosive to metals. INTEX 8565 Acid Paint Remover: An acid activated thick phenolic paint remover designed for the very difficult to remove modern paints. INTEX 8565 is nonchromated, safe on aluminum. Properties: Form: Thick Liquid Appearance: Blue Odor: Mild Acid Type PH: 0.8-2.0 Flash Point: None Rinsing: Free and Complete Use Dilutions: Use as received at room temperature. Apply with a brush, mop or spray. After the paint has completely blistered, flush with a high pressure water rinse. Note: If paint residues are a disposal problem, remove residues with a squeegee and collect in drums or containers for disposal. Safety on Materials: Use only with acid resistant equipment. Not safe on high strength steel and magnesium. Approvals: Mil-R-81903 Type #I


233

INTEX CHEMICAL, INC.: Paint Removers(Continued): INTEX 8570 Non-Phenolic Paint Remover: A thick non-phenolic solvent type paint remover developed for application by the flow-on method. Effective on modern finishes such as enamels, lacquers, and alkyds. Properties: Form: Liquid Appearance: Light yellow Odor: Solvent pH: 11.9-12.5 (Conc.) Rinsing: Free and complete Lbs./Gal.: 8.8 Use Concentrations: Use as received. D o not dilute. Apply with a brush or by nonatomizing spray, etc. Allow to set until paint blisters, then flush with a high pressure water rinse. Process Hints: (a) To insure clean surface, follow with water rinse. ( b ) Be sure stripping action is complete before rinsing. Titration: None Approvals: Mil-R-25134B Douglas CSD-1 T.0. 1-1-8 Safety on Materials: Non-corrosive to metals. Operating Temperatures: Minimum Operating--Ambient Maximum Operating--90F INTEX 8580 Paint/Seal Remover: A viscous non-phenolic solvent type paint remover and seal stripper for application by the flow-on method. It is effective in removing paints, varnishes, shellacs, and lacquers from metal or wood surfaces. Properties: Color: Cloudy liquid Odor: Solvent type pH: 7.0-8.0 Flash Point: None Rinsing: Free and complete Using Conc.: Use as is--do not dilute. Apply with a brush, spray nozzle, etc. On painted metal allow to set until paint blisters; then flush with a high pressure water rinse. On painted or sealed wood surface, do not allow to come in contact with the wooden surface Scrape off small area and on wooden floors, use a floor machine with steel wire brush. Safety on Materials: Non-corrosive to metals. Approvals: None Titration: None

234



Paint Removers(C0ntinued):

INTEX 8783 Stripper Additive: A non-phenolic solvent product use as an additive with alkaline paint strippers to aid in paint removal. Product is incompatible with oxidizing systems. Also used as a boil-out additive for resins, coatings and stubborn organic residues. Properties: Form: Liquid Appearance: Water White Odor: Pleasant Viscosity: Slightly more viscous than water Lbs./Gal.: 9.17 Use Concentrations: Use from 1% to 5% of 8783 by volume of tank capacity. Safety on Materials: Not safe on rubber. INTEX 8786 Hot Tank Paint Remover: A solvent two-phase hot tank paint remover especially formulated to remove modern finishes such as epoxies, urethane and acrylic lacquers. Properties: Form: Liquid (Two Phase) Appearance: Dark amber Odor: Solvent pH: 10.7-11.0 (Conc.) Rinsing: Free and complete Lbs./Gal.: 9.7 Use Concentrations: Hot Tank - Ready to use. Operating Temperatures: Minimum Operating--llOF. Maximum Operating--140F. Process Hints: (a) Parts must be completely immersed in solvent layer. (b) Follow stripping with water rinse. (c) Maintain 4-6 inch water seal. Titration: None Approvals: Mil-R-81835A (USAF) Mil-R-83936, Type 11, Class I1 Safety on Materials: Non-corrosive to metals.

lntex Chemical. lnc.


235

Paint Removers(Continued):

INTEX 8789 Hot Tank Paint Remover: A liquid chromated, non-phenolic, two-phase (mineral oil seal) hot tank paint paint & carbon remover for use on high strength steel or cadmium plated steel. Removes difficult finishes and carbon deposits from aircraft components. Will remove resins commonly found on aircraft heat exchangers. Properties: Appearance: Yellow/brown liq. (2 phase) Odor: Musty pH: 13 Foaming: None Rinsing: Free and Complete Lbs/gal: 8.6 Use Concentrations: Use as received. Process Hints: (a) Parts must be completely immersed in solvent layer. (b) Seal leaves a slight oily residue, therefore, parts must be pressure or hot water rinsed to remove all traces of seal. (c) Very effective in removing carbon. Approvals: Boeing D6-17487 CSD #1, Type I1 Operating Temperatures: Minimum Operating--140F. Maximum Operating--180F. INTEX 8791 Accelerated Boil-Out: A non-phenolic, solvent-alkali combination boil-out developed to remove the tough resins and residues that are non-responsive to other standard boil-outs. Properties: Color: Clear tan liquid Odor: Mildly Irritating pH Conc.: 13.5-14.0 Foaming: Almost None Rinsing: Free & Complete Hard Water Stability: Up to 500 ppm Biodegradable: Yes Phosphate Free Using Concentrations: Hot Tanks: Medium Duty 12.5% by volume = 8 ounces per gallon of dry product. Heavy Duty 25% by volume = 1 pound per gallon of dry product. Operating Temperatures: 180F.-200F. Safety on Materials: Not safe on alumimum or zinc.

-

-


INTEX CHEMICAL, INC.: Rust Preventatives: INTEX 8215 Oil Emulsifiable Rust Preventative: A unique oil emulsifiable rust preventative. It provides the best of two (2) rust preventative systems. An emulsion when mixed with water and also a water displacing product to give oiled rust preventative surface. Properties: Form: Liquid Appearance: Dark Brown Oil Odor: Mild pH: 10.5 Foaming: None Hard Water Stability: Excellent Lbs./Gal.: 7.9 Use Concentrations: 1. As a rust preventative oil use at 15% to 30% by volume. 2. For "Dry-Touch" surface use at 5% to 15% by volume at between 140F.-1 60F. Safety on Materials: Not tested on aluminum or soft metals. Process Hints: 1. INTEX 8215 will form an emulsion when mixed with water at minimum of 2% up to 30% maximum by volume. 2. Also, will yield 72 hours salt spray over zinc at 20% to 30% by volume. 3 . When the residual water volume equals the 8215 volume during Dry-Off cycle; the 8215 reverts to a water displacing rust preventative forcing the water carrier away from the parts. INTEX 8216 Rust Preventative: A rust preventive solvent designed to clean and degrease parts, leaving a thin rust preventive film. Non chlorinated version of 8221. Properties: Color: Clear Amber Liquid Odor: Solvent Type Flash Point: 145F. Using Concentrations: Tank Application: Full strength at room temperature. May also be used in dip, spraying, or wiping operations. Safety on Materials: Non-corrosive to metals. Approvals: None Titration: None

lntex Chemical, lnc.


237

Rust Preventatives:

INTEX 8220 Rust Preventive: INTEX 8220 is a blend of solvents and preservatives formulated to serve the metal-working industry in three ways. It will effectively combat rust during processing or indoor storage. It is an excellent compound for the removal and prevention of fingerprints. It is a water-displacing material. Application: INTEX 8220 is applied full strength to parts by dipping, brushing, spraying, or wiping. INTEX 8220 is used cold and undiluted, therefore, no heating or mixing is required. The film is easily removed by a strong water spray, should removal become necessary. Benefits : Prevents rusting between stages of fabrication. Displaces water without pre-drying. Assures fingerprint-free surfaces. Metal Compatibility: INTEX 8220 is non-corrosive to all metals, emits no disagreeable odors. It will not turn rancid, even in the hottest weather. INTEX 8224 Rust Preventive: An organic water type rust preventative compound designed to protect metal parts from rusting prior to painting. Properties: Color: Dark red liquid Odor: Mild pH (Conc.): 10.8-11.2 Foaming: None Using Conc.: Tank Application: Maximum dilution 1 to 1 0 0 (1 part 8224 to 100 parts water, 1 % solution). Minimum dilution 1 to 10 (1 part 8224 to 10 parts water, 10% solution). Safety on Materials: Safe on iron, steel and stainless steel. Approvals: None Titration: Mild Alkaline Test Kit (BCP Indicator) Titration Factor-0.25



Rust Preventatives(Continued):

INTEX 8 2 2 7 "NUT BUSTER": Intex 8227 is designed for use as a rust preventative/ penetrant for multiple applications. INTEX 8227 is a blend of solvents and preservatives that penetrate and loosen bolts, nuts, and gives rust protection. Properties: Color: Light amber Odor: Mineral spirits Form: Clear liquid pH: Not applicable Foam: None Hardwater Stability: Not applicable Rinsing: Not applicable Biodegradable: Not applicable Safety on Materials: Safe on all metals. Use Dilutions: 1 . Use as received. 2. Apply full strength by dipping, brushing, spraying, or wiping--used at room temperature. 3 . The film is easily removed by a strong water spray-when removal becomes necessary. Titration: Not applicable INTEX 8228 Rust Preventative: INTEX 8228 is a water dlutable rust preventative, designed for polished ferrous materials to prevent rust. INTEX 8228 is nitrite-free and non-toxic. Properties: Color: Red Odor: Bland Form: Liquid pH: 9.8 to 1 0 . 5 (Concentrate) Foam: None Hard Water Stability: 500 ppm Biodegradable: N/A Safety on Materials: Safe on iron, steel, and stainless steel. Dilutions: Tank Application: Maximum dilution 1 to 100 ( 1 part 8228 to 1 0 0 parts water, 1 % solution). Minimum dilution 1 to 1 0 ( 1 part 8228 to 1 0 parts water, 1 0 % solution). Do not water rinse - no clean-up necessary prior to start-up since 8228 leaves a dry film surface. Titration: Mild Alkaline Test Kit (BCP Indicator) Titration Factor: 0.2

lntex Chemical, lnc.


239

Rust Removers:

INTEX 8667:

A granular alkaline heavy duty hot tank compound for removing light rust, grease, oil, carbon scale, and paint from ferrous surfaces. Contains no phenols, cresols, chromates or phosphates. Properties: Form: Granular Appearance: Tan Odor: Irritating pH (1% solution): 13.0-13.5 Foaming: Medium Rinsing: Free & Complete Hard Water Stability: Up to 500 ppm Biodegradable: Yes Use Concentration: Cleaner/Light Rust Removal: 1 to 16 ( 8 oz. 8667 per gallon of water). Paint Stripper: 1 to 8 ( 1 lb. 8667 per gallon of water). Engine Blocks, Heads, Crankshafts, Etc.: In an Agilift Tank, 1 to 16 ( 8 oz. 8667 per gallon of water). Tumbler, Deburring & Burnishing: 2 to 5 lbs. 8667 to each tumbler load. Radiator Core, Vat Stripping/Cleaning: 8 to 16 oz. 8667 per gallon of water. Electrolytic Cleaning: Cleaning ferrous metals is easily accomplished with a 4 to 8 oz. solution of 8667 at 180F. Operating Temperatures: Minimum Operating - 190F. Maximum Operating - 210F. Safety on Materials: Safe on ferrous metals and magnesium. Approvals: U.S.D.A. - A2 Titration: Alkaline Test Kit Factor - .19 INTEX 8668 Hot Tank Rust Remover:

A granular alkaline heavy duty rust remover intended for use in hot tank operations. Contains no phenols, cresols, chromates, or phosphates. Properties: Color: White/Tan Powder Odor: Irritating pH: 1% solution - 13.3-13.7 Foaming: Low Rinsing: Free and complete Hard Water Stability: Up to 500 ppm Biodegradable: Yes Use Concentration: Heavy Duty Rust Remover: 1:8 (16 oz 8668 to each gallon of water). Scale/Rust: 1:3 (48 oz 8668 to each gallon of water). Material Safety: Safe on ferrous metals and magnesium. Approvals: Authorized by USDA in federally inspected meat and poultry plants. Titration: Alkaline Test Kit - Factor 0.22



Rust Removers(Continued):

INTEX 8655 Liquid Carbon and Rust Remover: A highly alkaline liquid rust and carbon remover developed to de-rust and clean jet engines. It can also be used as a rust remover, heavy duty cleaner and paint stripper in the metal processing industry. Properties: Appearance: Clear yellowish brown liquid Odor: Bland pH (Conc.): 13.5-14.0 Foaming: Low Rinsing: Free and complete Hard Water Stability: Up to 500 ppm Biodegradable: Yes Applications: Cleaning Jet Engines Rust Removing and Paint Stripping Heavy Duty Cleaning Cleaning Spinnerettes/Dyes Safety on Materials: Safe on ferrous metals and magnesium Approvals: Pratt & Whitney - Overhaul Letter No. 13 INTEX 8656 Liquid Rust Remover: A highly alkaline, liquid rust remover used by the metal processing industry. INTEX 8656 performs in a similar manner to INTEX 8663, a powdered product. Properties: Form: Liquid Appearance: Light brown Odor: Bland pH (Conc.): 13.5-14.0 Foaming: None Rinsing: Free and complete Hard Water Stability: Up to 500 ppm Use Concentrations: Hot Tanks -Thirty-two (32) ounces 8656 to each gallon of water. Sixty-four ( 6 4 ) ounces 8656 to each gallon of water. Operating Temperatures: Minimum operating - 180F. Maximum operating - 212F. Safety on Materials: Safe on ferrous metals only.

-


INTEX CHEMICAL, INC.: Rust Removers(Continued): INTEX 8663: A granular alkaline rust remover intended for use in a hot tank for removal of rust, oils, greases and some paints. Properties: Color: White powder Odor: Irritating pH: 1% solution--13.0-13.5 Foaming: None Rinsing: Free and complete Hard-Water Stability: Up to 500 ppm Biodegradable: Yes Use Concentrations: Hot Tank: Medium-duty--l:8 ( 1 pound 8663 to each gallon of water. ) Heavy-duty: 1:4 (2 pounds 8663 to each gallon of water). Operating Temperatures: Minimum: 180F. Maximum: 21 2F. Safety on Materials: Safe on ferrous metals only. Approvals: Pan Am Part No. 890-534; authorized by USDA for use in federally inspected meat and poultry plants. Titration: Alklaine Test Kit--Factor 0.21

24 1

242


JONES-BLAIR C O . : Aluminum Asphalt Base: Product Number: 930 Description: A bituminous base aluminum coating for use on asphalt surfaces such as roofs, roof parapets and flashings. Type: Special Resins Use: Maintenance coating Suitable for: Roofs, flashings, underground tanks and piping. Principal Uses: Excellent for coating exteriors of underground tanks and piping. Type of Exposure: Corrosion resistant. Tough weather resistant finish. Finish: High Gloss Colors: Aluminum Recommended Dry Film Thickness per Coat: 1 mil No. of Coats Required: One Total Dry Film Thickness: 1 Mil Total Weight Solids: 42% Total Volume Solids: 31% Theoretical Coverage: 5 0 0 sq. ft./gal @ 1 mil Coverage @ 2 mils: 250 sq. ft./gal. Surface Preparation: Must be clean, dry and free from wax, grease and foreign matter. Remove all loose and scaling material by sanding, wire brush. Recommended Primers: Self Priming No. of Components: One Apply Over: Asphalt Surfaces Metal Apply By: Bristle Brush (avoid excessive brushing) Drying Times: To Touch: 1 Hour To Recoat: 6-8 hours Hard: Overnight Cure Schedule: Air Dry Thinner: JB 1 5 2 APEX Clean Up: APEX Recommended Reduction: Up to 1 0 % by Volume Flash Point: 45F Volatile Organic Compounds: 4.5 lbs/gallon Weight per Gallon: 7 . 8 t . l lb/gal Viscosity as Supplied: 12-14 Sec F4 Packaging: 1 , 5

Jones-Blair Co.

JONES-BLAIR

CO.:

243

Aluminum Bright Finish-Supreme:

Product Number: 931 Description: Formulated for maximum brilliance and reflectivity. Properly applied, lapping and brush marks will not show. Type: Special Resin Use : Maintenance coating with maximum hiding, durability and protection Suitable for: Storage Tanks Principal Uses: For general use on exterior-interior metal or wood surfaces. Type of Exposure: Tough weather resistance finish with excellent gloss and color retention. Finish: Medium Gloss Colors: Aluminum Recommended Dry Film Thickness per Coat: 1 Mil No. of Coats Required: One Total Dry Film Thickness: 1 Mil Total Weight Solids: 54.0% Total Volume Solids: 43.7% Theoretical Coverage: 684 sq. ft./gal. @ 1 Mil Coverage @ 2 Mils: 342 sq. ft./gal. Surface Preparation: Previous coatings must be clean, dry, and free from any foreign matter. Recommended Primers: 981 RUST NOT 975 MULTI-GRIP 942 MIST COAT 1 1 151 7 2 / 1 5 5 7 2 Multipurpose Pr. . 9 7 2 Zinc Ch. Pr. No. of Components: 1 Apply Over: Primed Metal Apply by: Brush, Roller or Spray Drying Times: To Touch: 30 Minutes To Recoat: 6-8 Hours overn ght Cure Schedule: Air Dry Thinner: APEX 1 5 1 , 20653, 52 Clean Up: Same Recommended Reduction: Up to 1 0 % by volume Flash Point: 45F Volatile Organic Compounds: 3.78 lbs/gallon Weight per Gallon: 8.18 lbs/gal Viscosity as supplied: 33-36 Sec. F4 Packaging: 1 / 0 , 1 / 4 , 1, 5


JONES-BLAIR CO.:

Aluminum Brilliant Finish:

Product Number: 917 Description: An all-purpose aluminum paint pigmented with the highest quality pigment designed to produce a brilliant metallic effect. Type: Special Resins Use: Exterior-interior metal or wood surfaces. Suitable for: Storage tanks, pipes Principal Uses: Excellent durability on exterior and interior wood and metal surfaces. Type of Exposure: Exterior durability Finish: Low G l o s s Colors: Aluminum Recommended Dry Film Thickness per Coat: 1 Mil No. of Coats Required: One Total Dry Film Thickness: 1 Mil Total Weight Solids: 40% Total Volume Solids: 30% Theoretical Coverage: 500 sq.ft./gal. @ 1 mil Coverage @ 2 Mils: 250 sq.ft./gal. Surface Preparation: Surface must be clean and dry. Prime unpainted metal with 981 RUST-NOT Primer. 942 MIST COAT for non-ferrous metals; galvanized, aluminum, copper. Recommended Primers: 981 RUST NOT 942 MIST COAT 1 1 975 MULTI-GRIP Apply over: Primed Metal No. of Components: 1 Apply By! Brush, spray, roller Drying Times: To Touch: 1 hour To Recoat: 6-8 Hours Hard: Overnight Cure Schedule: Air Dry Thinner: APEX Clean Up: Same Recommended Reduction: 10% by volume Flash Point: 45F Volatile Organic Compounds: 4.6 lbs/gallon Weight per Gallon: 7.6i.1 lbs/gal Viscosity as supplied: 12-14 F4 Packaging: 1 , 5

Jones-Blair Co.

JONES-BLAIR CO.:

245

Aluminum Super Speed:

Product Number: 922 Description: A very fast drying aluminum paint. Produces maximum brilliance and high reflectivity. Type: Special Resins Use: General Maintenance Suitable for: Storage tanks, piping Principal Uses: For general use on exterior-interior metal or wood surfaces where speed of dry and durability is important. Type of Exposure: Excellent exterior durability and maximum reflectivity. Finish: High Gloss Colors: Aluminum Recommended Dry Film Thickness per Coat: 2 Mils No. of Coats Required: One Total Dry Film Thickness: .8 Mil Total Weight Solids: 39.0% Total Volume Solids: 31.0% Theoretical Coverage: 500 sq.ft./gal @ 1 mil Coverage @ 2 mils: 250 sq.ft./gal. Surface Preparation: Previous coatings must be clean, dry and free from any foreign matter. Recommended Primers: 942 MIST COAT 11 975 MULTI-GRIP 976 Zinc Chromate Primer 981 RUST NOT 151 7211 5572 Multipurpose Pr. No. of Components: 1 Apply Over: Primed metal Apply by: Spray Drying Times: To Touch: 10-15 minutes To Recoat: 2-4 Hours Cure Schedule: Air Dry Thinner: 151, 20653, 20654 Clean Up: Same as above Recommended Reduction: Up to 1 0 % by volume Flash Point: 80F Volatile Organic Compounds: 4.94 lbs/gallon Weight per Gallon: 8.15k.1 lbs/gal Viscosity as Supplied: 10-15 F4 Packaging: 1 , 5


JONES-BLAIR CO.:

CHEM-0-CONE Heat Resistant Coatings:

Product Number(s): 63511, 63512 Description: High Temperature air dry enamel Type: Modified Silicone Use: Heat Resistant Coating; also to prevent chloride stress cracking in stainless steel. Suitable for: Stainless steel or sandblasted steel. Principal Uses: Heat Resistance; to prevent chloride stress cracking in stainless steel. Type of Exposure: High temperature and/or chloride fumes. Finish: Low Gloss Colors: Black #63511 Gray #63512 Recommended Dry Film Thickness per Coat: 1-1.5 mils No. of Coats Required: one Total Dry Film Thickness: 1-1.5 mils Total Weight Solids: 39.5% Total Volume Solids: 26.6% Theoretical Coverage: 427 sq. ft./gal. @ 1 mil Coverage @ 1.5 mils: 284 sq.ft./gal. Surface Preparation: Abrasive blast steel solvent clean stainless steel. Recommended Primers: 63109 - CHEM-0-CONE Primer 99310 - CHEM-0-2 Inorganic Zinc Primer No. of Components: one Apply over: blasted steel or stainless steel Apply by: Conventional airless Drying Times: 15 minutes to touch To Recoat: 15-30 minutes Hard: full cure after 20 min. at 400F or 24 hrs at 250F Cure Schedule: Heat is required to achieve full cure. Thinner: Aromatics Clean Up: Aromatics Recommended Reduction: 10-20% as needed Temperature Resistance: Up to 650F Flash Point: 78F Volatile Organic Compounds: 5.15 lbs/gallon Weight per Gallon: 8.5 lbs/gallon Viscosity as Supplied: 60 K.U. Packaging: 1 gallon

Jones-Blair Co.

JONES-BLAIR CO.:

247

CHEM-0-LITE Chemical Resistant Vinyl:

Product Number: 5501 5 Description: Medium gloss vinyl resin coating Type: Vinyl Use: Maintenance Coating Suitable for: Storage Tanks Principal Uses: Topcoat vinyl enamel designed for corrosion protection and superior resistance to acids, chemical fumes, and spillage. Not for use where resistance to aromatic hydrocarbons, acetates or ketones is required. Type of Exposure: Exterior, used for weather resistance, chemical resistance Finish: Medium Gloss Colors: Off White Recommended Dry Film Thickness per Coat: 2-3 Mil No. of Coats Required: One wet coat Total Dry Film Thickness: 2-3 Mils Total Weight Solids: 46.6*1% Total Volume Solids: 30?1.0% Theoretical Coverage: 477 sq.ft./gal. @ 1 Mil Coverage @ 3 Mils: 159 sq.ft./gal. Surface Preparation: 55104 CHEM-0-LITE Interior 15572 Multi-Purpose Primer No. of Components: One Mixing Ratio: N/A Maximum Pot Life: N/A Apply Over: Cleaned Previous Coating Apply by: Spray Drying Times: To touch: 1 hour To Recoat: 4 Hours Hard: Overnight Cure Schedule: Air Dry Thinner: 20200 Clean Up: 20200 Recommended Reduction: Up to 25% Flash Point: 1OOF Volatile Organic Compounds: 4.98 lbs/gallon Weight per Gallon: 9.3i.1 Viscosity as Supplied: 80-100 F4 Packaging: 5 Gallon


JONES-BLAIR CO.:

CBEM-0-LITE Primer:

Product Number: 5551 6 Description: Vinyl Resin Coating modified to achieve maximum adhesion over ferrous or zinc substrates. Type: Vinyl Primer Use: Primer or Intermediate Topcoat Suitable for: Ferrous and Zinc Substrates Principal Uses: May be used over treated or untreated steel substrates or as a barrier coat over CHEM-0-2 primers. May also be used solely as a 2-coat finishing system for non-severe exposure. Type of Exposure: Anti-corrosive primer for subsequent vinyl topcoats. Finish: Semi-Gloss Colors: Gray Recommended Dry Film Thickness per Coat: 1.5-2.0 Mils No. of Coats Required: One, for most applications. Total Weight Solids: 34.8521% Total Volume Solids: 20.021% Theoretical Coverage: 315 sq.ft./gal. @ 1 mil Coverage @ 2 Mils: 158 sq.ft./gal. Surface Preparation: Metal to be free from dirt, oil, water, or other foreign matter. Preferably applied over blasted surfaces. Recommended Primers: Self priming No. of Components: One Mixing Ratio: N/A Maximum Pot Life: N/A Apply Over: Ferrous and Zinc Substrates Apply By: Spray air or airless Drying Times: To Touch: 15 minutes To Recoat: 30-45 minutes Hard: Overnight Cure Schedule: Air Dry Thinner: 20200 Clean Up: 20200 Recommended Reduction: 10-1 5% Flash Point: 74F Volatile Organic Compounds: 5.7 lbs/gallon Weight per Gallon: 8.751t1 lblgallon Viscosity as Supplied: 40-50 F4 Packaging: 5 Gallon Cans

Jones-Blair Go.

JONES-BLAIR CO.:

249

CHEM-0-LITE Vinyl Colors:

Product Number(s): 5 5 1 0 4 , 5 5 0 1 6 , 5 5 3 0 4 Description: Vinyl Resin Coating modified to give good adhesion to organic primers and vinyl topcoats. Type: Vinyl Use: Maintenance Coating Suitable for: Storage Tanks Principal Uses: Designed as a topcoat or intermediate vinyl coating to be used over primed metal surfaces. Exhibits excellent adhesion to organic (non-vinyl based) primers. May be subsequently topcoated with CHEM-0-THIX, CHEM-0-PLEX enamels or with itself (CHEM-0-LITE coatings). Type of Exposure: Exterior, for use weather resistance, chemical resistance Finish: Med. Gloss Colors: Red, Gray, Green Recomended Dry Film Thickness per Coat: 1 . 5 - 2 . 0 Mils No. of Coats Required: 2 wet coats Total Dry Film Thickness: 1 . 5 - 2 Mils Total Weight Solids: 3 2 - 3 7 % Total Volume Solids: 2 1 . 0 - 2 6 . 5 % Theoretical Coverage: 3 3 6 sq. ft./gal. @ 1 Mil Coverage @ 2 Mils: 1 6 8 sq. ft./gal. Surface Preparation: Previous coatings to be free from dirt, oil, water, or other foreign matter. Recommended Primers: 1 5 1 7 2 , 1 5 5 7 2 Multi-Purpose Primer and 9 4 2 MIST COAT 1 1 . No. Of Components: One Mixing Ratio: N/A Maximum Pot Life: N/A Apply Over: Cleaned or primed metals Apply by: Air or Airless Spray Drying Times: To Touch: 1 5 minutes To Recoat: 3 0 minutes Hard: Overnight Cure Schedule: Air Dry Thinner: 2 0 2 0 0 Clean Up: 2 0 2 0 0 Recommended Reduction: up to 2 5 % Flash Point: 1 3 0 F Volatile Organic Compounds: 5 . 2 - 5 . 5 Weight per Gallon: 8 . 2 8 - 9 . 4 7 Viscosity as Supplied: 90-110 F4 Packaging: 1 , 5 gallon

lbs/gallon


JONES-BLAIR CO.:

CHEM-0-PON High Solids, High Build EPOXY Primer:

Product Number: 39020 Description: High Build, high solids, rust inhibitive, zinc chromate containing, epoxy/polyamide coating. Packaged as a two-component system. Type: High Build, High Solids 2-part epoxy Use: Maintenance and Marine Surfaces Suitable for: Steel, Concrete or CHEM-0-2 intermediate. Principal Uses: As an original primer over properly prepared metal, or as a high build intermediate coat over CHEM-0-2 Inorganic or Organic Zinc Rich coatings. Type of Exposure: Designed for maximum corrosion protection in strong alkaline and moderate acid conditions. Also in high moisture and salt exposure. Finish: 7 0 Gloss on smooth surfaces Colors: Pale Greenish-Gray Recommended Dry Film Thickness per Coat: 5-7 mils No. of Coats Required: 1 Heavy Coat Total Dry Film Thickness: 5-7 mils Total Weight Solids: Base only 7 7 + 1 % Catalyzed 7 2 ~ 1 % Total Volume Solids: Base only 60*1% Catalyzed 59_+1% Theoretical Coverage: 190 sq.ft./gal @ 5 Mil Coverage @ 7 mils: 135 sq.ft./gal. Surface Preparation: SSPC #5 (NACE # 1 ) White metal blast is recommended for severe exposure; otherwise SSPC #6 (NACE # 3 ) commercial blast Recommended Primers: CHEM-0-2 Inorganic or Organic Zinc Rich Coatings for marine or offshore exposure. No. of Components: 2 Mixing Ratio: 3:l mix, 39020:99906 Maximum Pot Life: 4-6 hours Apply over: Zinc Primer or properly prepared steel Apply by! Airless spray preferred; conventional spray also Drying Times: To touch - 4 hours To Recoat: 6 hours (if necessary) Hard: 24 hours Cure Schedule: Catalyzed Thinner: 21064 for spray Clean Up: 21064 Recommended Reduction: Up to 1 0 % if necessary Temperature Resistance: 300F Dry Heat Flash Point: 81 F Volatile Organic Compounds: 2 . 8 8 lbs/gallon Weight per Gallon: 1 2 . 5 5 ; 1 1 . 3 6 catalyzed Viscosity as Supplied: 90-100 K.U.

Jones-Blair Co. 251

JONES-BLAIR CO.:

CAEM-0-PON Zinc Chromate Epoxy Primer:

Product Number: 3991 6 Description: High solids polyamide cured rust inhibitive zinc chromate epoxy primer. Packaged as a two-component system. Type: Epoxy - Polyamide Use: Maintenance and Marine Surfaces Suitable for: Steel, CHEM-0-2, Concrete Principal Uses: Use as an original primer over properly prepared metal, or as an intermediate coat over CHEM-0-2 primers. Type of Exposure: Designed for maximum corrosion protection in strong alkaline and moderate acid conditions. Also in high moisture and salt exposure. Finish: Low Gloss Colors: Yellow Recommended Dry Film Thickness per Coat: 3-5 mils No. of Coats Required: One Total Dry Film Thickness: 3-5 Total Weight Solids: Base only 7 7 i 1 % Catalyzed 7 2 . 4 % Total Volume Solids: Base only: 60*1% Catalyzed: 5 9 . 1 % Theoretical Coverage: 316 sq.ft./gal @ 3 . 0 mil Coverage @ 5 mils: 1 9 0 sq. ft./gal. Surface Preparation: SSPC #5 (NACE # 1 ) White metal blast is recommended for severe exposure; otherwise SSPC #6 (NACE # 3 ) commercial blast. Recommended Primers: CHEM-0-2 Inorganic or organic Zinc Rich coatings for marine or offshore exposure. No. of Components: Two Mixing Ratio: 3 : l mix, 39916:99906 Maximum Pot Life: 8 hours Apply Over: Zinc Primer or properly prepared steel Apply by: Air or Airless spray Drying Times: To Touch: 2 hours To Recoat: 4 hours Hard: 2 4 hours Cure Schedule: Catalyzed Thinner: 21 0 6 4 Clean Up: 2 1 0 6 4 Recommended Reduction: Up to 1 5 % by volume Temperature Resistance: 300F Dry Heat Flash Point: 45F Volatile Organic Compounds: 2 . 8 8 lbs/gallon Weight per Gallon: 1 2 . 4 5 ; 1 1 . 3 catalyzed Viscosity as Supplied: 90-100 Krebs Units @ 77F Packaging: 3 gallon fill in 5 gallon pail


JONES-BLAIR CO.:

CHEM-0-THIX High Build Vinyl:

Product Number(s): 55010/55014 Description: Vinyl Resin Coatings designed to give high film build in one coat. Type: Vinyl Use: Maintenance coating Suitable for: Steel Principal Uses: Topcoat vinyl enamel designed for corrosion protection and superior resistance to acids, chemical fumes, and spillage. Type of Exposure: Used for weather resistance, chemical resistance Finish: Low Gloss Recommended Dry Film Thickness per Coat: 5-8 Mils No. of Coats Required: 1 heavy wet coat Total Weight Solids: 48.5k1.0 Total Volume Solids: 28.0+1.0 Theoretical Coverage: 420 sq.ft./gal @ 1.0 mil Coverage @ 2 Mils: 210 sq.ft./gal. Surface Preparation: Previous coatings to be free from dirt, oil, water, or other foreign matter. No. of Components: One Apply over: Cleaned metal surfaces Apply by: Air or Airless Spray Drying Times: 3-4 hours to Handle Cure Schedule: Air Dry Thinner: 20200 Clean Up: 20200 Recommended Reduction: Up to 5% Flash Point: 22F Volatile Organic Compounds: 5 2 Lbs/Gallon Weight per Gallon: 10.1 3 + . 1 Viscosity as Supplied: 80-100 KU Packaging: 5 Gallon

Jones-Blair Co.

JONES-BLAIR CO.:

-

253

HEAT-BAN 5185 White:

Cools - Reflects radiation...reduces indoor temperatures as much as 25%. Beautifies - Snow-white may be tinted in various harmonizing shades Prolongs Roof Life - Years added to roofs treated with HEATBAN

...

Excellent for Mobile Home Roofs Jones-Blair HEAT-BAN cools, protects and beautifies all kinds of roofs--homes, office, industrial buildings, apartment buildings, farm and ranch structures--both new and existing construction. HEAT-BAN is a polyvinyl acetate base material, snow white in color. It adheres to roofing materials such as rock and gravel, aged asphalt shingles, masonry, tile and nonstabilized galvanized metal, asphalt and tar and is resistant to bleeding, fading, chalking or cracking. JB HEAT-BAN has been developed specifically where extreme summer heat causes high indoor temperatures. HEAT-BAN reflects the sun's rays and reduces inside temperatures 1 5 to 25. The result is a cooler, more comfortable home. Less drain is placed on air cooling or air conditioning equipment. Costs are reduced up to 25 per cent Adds Years to Roof Life! The slow loss of gravel during rain or high winds is prevented by JB HEAT-BAN, halting the disintegration of such roofs. Years of life are added to roofs treated with JB HEAT-BAN. It slows up evaporation of volatile oils and tars in sub-roof materials. Water-proofing compounds last longer and tar paper doesn't dry out as quickly and become brittle. HEAT-BAN adheres to and protects aged asphalt shingles. It provides freedom from future roof maintenance by reflecting damaging ultra violet rays. New gravel roofs that are to be coated with HEAT-BAN should have 1 5 0 lbs. of rock per 1 0 0 sq. ft. embedded in last flood coat of asphalt. Covers economically: Depending on roof condition, each 1 0 0 sq. ft. requires 2 gallons of material. And It Means a More Beautiful Home All Year Long! Roofs painted with HEAT-BAN appear modern and beautiful. The snow-white surface, for example, can be sprinkled with cut glass to sparkle and glitter in the sunlight or Universal Tinting Colors can be used to tint HEAT-BAN to soft, beautiful pastel shades, so the roof harmonizes with any exterior color scheme. HEAT-BAN does not reduce temperature as much when tinted. To a crushed rock or gravel roof, HEAT-BAN provides additional beautifying advantages. Ugly, black exposed areas caused by material being washed or blown away are reduced. Gravel falling in flower beds, on sidewalks, driveways or patios is minimized.

...


JONES-BLAIR CO.: Heat Resistant Aluminum: Product Number: 919 Description: A premium quality, high heat resistant finish developed especially to withstand prolonged temperatures of 600F. Type: Special Resin Use : For exterior-interior metal and wood surfaces to withstand prolonged temperatures of 600F. Suitable for: Wood, masonry, metal boiler fronts, pipes and engines Principal Uses: Excellent for boiler fronts, engines and steam pipes. Finish: High Gloss Colors: Bright Alumimum Recommended Dry Film Thickness per Coat: 1.2 mils per coat No. of Coats Required: One Total Dry Film Thickness: 1.2 mils Total Weight Solids: 54% Theoretical Coverage: 600 sq.ft./gal. @ 1 Mil Coverage @ 2 Mils: 300 sq.ft./gal. Surface Preparation: Must be clean, dry and free from wax, grease and foreign matter. Recommended Primers: Self Priming, 942 MIST COAT 11, 975 MULTI-GRIP, 976 Zinc Chromate primer, 981 RUST NOT, 971 POLYFLEX No. of Components: 1 Apply Over: Cleaned wood, masonry, metal surfaces Apply by: Brush, Roller or Spray Drying Times: 1 Hour To Recoat: 6-8 Hours Cure Schedule: Air Dry Thinner: JB 152 APEX-Brushing, JB 151-Spraying Clean Up: JB 152 APEX-Brushing, JB 151-Spraying Recommended Reduction: Up to 10% by volume Temperature Resistance: Up to 600F Flash Point: 80F Volatile Organic Compounds: 3.7 lbs/gallon Weight per Gallon: 8.2k.1 lbs/gal Viscosity as Supplied: 25-30 Sec F4 Packaging: 114, 1 , 5

Jones-Blair Co.

JONES-BLAIR CO.:

255

MIST COAT I1 Vinyl Wash Primer:

Product Number: 9 4 2 Description: Two component acid etching zinc chromate vinyl wash primer. # 9 4 2 Base: #188 Accelerator. Type: Vinyl Use: Metal me-treatment for non-ferrous metals Suitable fo;: Aluminum, galvanized, copper Principal Uses: Metal pretreatment for non-ferrous metals. Aluminum, copper, galvanized) prior to priming. May also be used as the base coat in some vinyl systems. Finish: Low Gloss Colors: Greenish Yellow Recommended Dry Film Thickness per Coat: .1 - 3 Mils No. Of Coats Required: 1 light wet coat Total Dry Film Thickness: Do not exceed .5 mils Total Weight Solids: 17.3% Surface Preparation: SSPC #5 preferred. Surface should be free from rust, dirt, oil, water or other foreign matter. Recommended Primers: Self priming No. of Components: Two Mixing Ratio: 1:l with 188 catalyst Maximum Pot Life: 8 Hours Apply Over: Cleaned aluminum, copper or galvanized metals Apply by: Air Spray/Brush Drying Times: To Touch: 5 minutes To Recoat: 1 0 minutes Cure Schedule: Air Dry Thinner: Alcohol Clean Up: Alcohol Recommended Reduction: Up to 5% Flash Point: 55F Volatile Organic Compounds: 6.05 lbs/gallon Weight per Gallon: 7.3 lbs/gal Viscosity as Supplied: 50-65 sec F4 Packaging: 1 , 5

256


JONES-BLAIR CO.:

MULTI-GRIP Acrylic Latex Primer:

Product Number: 9 7 5 Description: Acrylic Latex Primer Type: Acrylic Emulsion Use: Interior and exterior primer for metal. Suitable for: Galvanized Iron Principal Uses: Especially recommended as a primer for interior/exterior galvanized iron. Type of Exposure: Where corrosion protection is needed. Finish: Low Gloss Colors: White Recommended Dry Film: 1 Mil Thickness per Coat: 2-3 Mils No. of Coats Required: One Total Dry Film Thickness: 1 Mil Total Weight Solids: 56+1% Total Volume Solids: 41&1% Theoretical Coverage: 5 5 0 sq. ft./gal @ 1 mil Coverage @ 2 Mils: 3 3 8 sq. ft./gal. Surface Preparation: Must be clean, free of wax, oil and grease Recommended Primers: Self No. of Components: 1 Mixing Ratio: None Maximum Pot Life: N/A Apply Over: Galvanized metal Apply by: Brush, Roller or Spray Drying Times: To Touch: 30 minutes To Recoat: 1 Hour Hard: Overnight Cure Schedule: Air Dry Thinner: Water Clean Up: Water Recommended Reduction: Up to 20% by Volume Flash Point: None Weight per Gallon: 11 .2+.1 lbs/gal Viscosity as Supplied: 78-85 KU Packaging: 5 , 1, 1 / 4

Jones-Elair Co.

JONES-BLAIR CO.:

257

MULTI-PURPOSE Primer:

Product Number: 151 72, 15572 Description: Rust inhibitive primer. Packaged as a single system. Type: Modified Phenolic Use: Multi-Purpose Primer Suitable for: Steel or Iron Principal Uses: A base coat for alkyd, vinyl, & epoxy topcoats. Can be used as a primer-surfacer when allowed to dry overnight. Type of Exposure: Interior or exterior Finish: Low Gloss Colors: 15172 Red, 15572 Gray, 25148 Lt. Yellow Recommended Dry Film Thickness per Coat: 2 Mils No. of Coats Required: One Total Dry Film Thickness: 1.5-2 Mils Total Weight Solids: 52.3&1% Total Volume Solids: 32.44% Theoretical Coverage: 520 sq.ft./gal. @ 1 Mil Coverage @ 2 mils: 260 sq. ft./gal. Surface Preparation: SSPC #6 Commercial Blast preferred. Surface must be clean free from any rust, dirt, oil, water or foreign matter. No. of Components: One Apply Over: Clean Metal (Sandblast preferred) Apply by: Air, airless, brush or roller. Drying Times: To Touch: 15 minutes To Recoat: 1 Hour Hard: 24-48 Hours Cure Schedule: Air Dry Thinner: 20653 Clean Up: 20653 Recommended Reduction: 10-25% or as needed Flash Point: 81F Volatile Orgnic Compounds: 7.0 Lbs/Gallon Weight per Gallon: 10.0+0.10 Lbs. Viscosity as Supplied: 35-45 F4 Packaging: 1,5, & 55 Gallons

&


JONES BLAIR CO.:

RUST-NOT

Metal Primer White:

Product Number: 1970 Description: Rust inhibitive primer which is extremely durable, weather and corrosion resistant. Type: Alkyd Use: Rust Inhibitive Primer Suitable for: Iron and Steel Principal Uses: For use under white and light colored finish coats. Type of Exposure: Interior and Exterior Finish: Low gloss Colors: White Recommended Dry Film Thickness per Coat: 1-3 mils N o . of Coats Required: One Total Dry Film Thickness: 1-3 mils Total Weight Solids: 74.7% Total Volume Solids: 52.5% Theoretical Coverage: 842 sq. ft./gal. @ 1 mil Coverage @ 3 mils: 281 sq. ft./gal. Surface Preparation: Surface must be clean, dry, and free from wax, grease, and foreign matter. N o . of Components: One Apply Over: Iron and Steel Apply by: Brush, roll or spray Drying Times: 8 hours to touch To Recoat: 18 hours to recoat Hard: 24 hours Cure Schedule: Air Dry Thinner: BRUSH-APEX #152, Spray-#l51 Clean Up: Aliphatics Recommended Reduction: 10-25% as necessary Temperature Resistance: 200 F Flash Point: 112F Volatile Organic Compounds: 3.09 lbs/gallon Weight per Gallon: 12.2i.5 lbs per gallon Viscosity as Supplied: 75-85 K.U. Packaging: quarts, 1 gallon, 5 gallons

Jones-Blair Co.

JONES-BLAIR CO.:

259

RUST-NOT Metal Primer Red-Brown:

Product Number: 971 DescriDtion: Rusk inhibitive primer which is extremely durable, weather and corrosion resistant. Type: Alkyd-Oil Use: Rust Inhibitive Primer Suitable for: Iron and Steel Principal Uses: For general maintenance use and for incipient rust penetration Type of Exposure: Interior and Exterior Finish: Low gloss Colors: Red-Brown Recommended Dry Film Thickness per Coat: 1-3 mils No. of Coats Required: one Total Dry Film Thickness: 1-3 mils Total Weight Solids: 74% Total Volume Solids: 51.5% Theoretical Coverage: 826 sq. ft./gal. @ 1 mil Coverage @ 3 mils: 275 sq.ft./gal. Surface Preparation: Surface must be clean, dry, and free from wax, grease and foreign matter. No. of Components: One Apply Over: Iron and Steel Apply By: Brush, roll and spray Drying Times: 8 hours to touch To Recoat: 18 hours to recoat Hard: 2 4 hours Cure Schedule: Air Dry Thinner: BRUSH-APEX #152 , Spray-#l51 Clean Up: Aliphatics Recommended Reduction: 10-25% as necessary Temperature Resistance: 200F Flash Point: 112F Volatile Organic Compounds: 3.16 lbs/gallon Weight per Gallon: 12.12k.5 lbs per gallon Viscosity as Supplied: 65-75 K.U. Packaging: quarts, 1 gallon, 5 gallons


JONES-BLAIR CO.:

STANTEST Red-Brown Oxide Primer:

Product Number: 1521 1 Description: A general purpose primer that gives good rust protection at low cost. Type: Modified Alkyd Use: Shop coat primer for corrosion protection of steel Suitable for: Iron or steel Principal Uses: Shop coat primer for structural steel, fabricated parts and miscellaneous maintenance applications. Finish: Low Gloss Colors: Red-Brown oxide Recommended Dry Film Thickness per Coat: 1-1.5 mils No. of Coats Required: One Total Dry Film Thickness: 1-1.5 mils Total Weight Solids: 55.2% Total Volume Solids: 37% Theoretical Coverage: 593 sq.ft./gal:@ 1 mil Coverage @ 1.5 mils: 396 sq.ft./gal. Surface Preparation: Surface must be clean and free from any rust, dirt, oil, water, and foreign matter. No. of Componenets: One Apply Over: Clean ferrous substrates Apply by: Airless or air spray Drying Times: 20-30 minutes to handle To Recoat: 10-12 hours Hard: Overnight Cure Schedule: Air Dry Thinner: Aromatics Clean Up: Aromatics Recommended Reduction: Up to 10% maximum Temperature Resistance: 200F Flash Point: 75F Volatile Organic Compounds: 4.45 lbs/gallon Weight per Gallon: 9.9t.5 lbs per gallon Viscosity as Supplied: 35-42 seconds #2 Zahn Packaging: 5, 55

Jones-Blair Co.

26 1

JONES-BLAIR CO.: UNI-FLEX Architectural Textured Coating: Concrete Plaster Masonry Hadite or Concrete Blocks stucco Galvanized Metal Asbestos Siding Wood Sheetrock Fungus and Mildew Resistant Fire Resistant Good Insulation Value

-

UNI-FLEX is a heavy bodied vinyl acrylic coating, for use on practically all types of exterior and interior wall and ceiling surfaces. UNI-FLEX is a protective and decorative coating for vertical surfaces and ceilings, hiding minor imperfections and bridging hairline cracks. UNI-FLEX is available in three grades: No. 3100 Fine and No. 3200 Medium are for use on all exterior or interior masonry surfaces, primed wood, galvanized metal, sound plaster, and rock or gypsum wallboard. No. 3360

Coarse is for use on the same surfaces as Fine and Medium. Due to the larger and softer aggregate used in the Coarse, Jones-Blair recommends this grade for ceilings or out of reach areas. Coarse has all weather resistant properties of the Fine and Medium, but does not have the abrasion resistance. The only difference between No. 3200 and No. 3360 is the aggregate size.

Surface Preparation: Concrete/Hadite Blocks: Very porous surfaces usually require two thin coats of UNIFLEX. Masonry/Stucco/Plaster: Surface must be firm and clean. Slightly damp surfaces may be coated. Apply two coats by spraying allowing 8 to 1 0 hours between coats. Asbestos Siding: Due to the porosity and chalking caused by weathering of this type surface, particular care must be taken before applying UNI-FLEX. Galvanized Metal Surfaces: Allow new surfaces to weather 60 days or longer then spray but not when surface is hot. Wood Surfaces: Exterior/Interior: Prime Sheetrock/Gypsum Wallboard: Drywall surfaces should be taped, bedded and sanded smooth prior to application of UNI-FLEX.


JONES-BLAIR CO.:

UNIVERSAL VINYL Primer:

Product Number: 15204 Description: Universal type rust inhibitive primer packaged as a single system Type: Vinyl-Alkyd Use: A universal rust-inhibitive primer Suitable for: Iron or Steel Principal Uses: Primer for alkyd, vinyl, urethane, and epoxy topcoats. May also be used as a barrier coat over zinc surfaces. Type of Exposure: Interior or exterior with suitable topcoat. Finish: Low Gloss Colors: Red Recommended Dry Film Thickness per Coat: 1.5-2 Mils No. of Coats Required: One Total Dry Film Thickness: 1.5-2 Mils Total Weight Solids: 54.8i1.0% Total Volume Solids: 33.0t1.0% Theoretical Coverage: 529 sq.ft./gal @ 1.0 Mil Coverage @ 2.0 Mils: 265 sq.ft./gal. Surface Preparation: SSPC #6 commercial blast preferred. Surface must be clean and free from any rust, dirt, oil, water or foreign matter. NO. of Components: .One . Mixing Ratio: N/A Maximum Pot Life: N/A Apply Over: Iron or Steel see surface preparation) or Zinc Rich Coatings Drying Times: To touch: 10 minutes To Recoat: 1 hour Hard: 4 hours Cure Schedule: Air Dry Thinner: 20200 Clean Up: 20200 Recommended Reduction: Up to 10% by volume Temperature Resistance: 200F Flash Point: 74F Volatile Organic Compounds: 4.72 Lbs/Gallon Weight per Gallon: 10.45k.10 lbs Viscosity as Supplied: 30-40 #4 Ford Cup Packaging: Ones, Fives, Drums

Kop-Coat, lnc.

KOP-COAT, INC.:

263

BITUMASTIC Black Solution:

A self-priming protective coating formulated with refined tars, special solvents and selected ingredients. It has a consistency of thin fluid paint or varnish and does not contain added fillers or fibers. For industrial use only. Not intended for use in the home. Recommended as a general maintenance coating to provide a waterproof finish for metal or concrete. It is designed for use under moderate corrosive conditions as experienced in the fumes of industrial acids, alkalis and chemicals. Do not use on the interiors of potable water tanks or containers as BITUMASTIC Black Solution will impart taste to the water. When exposed to sunlight and effects of weathering, the coating should be aged approximately 2 to 4 weeks then topcoated with BITUPLASTIC No. 28 or BITUPLASTIC No. 33. This minimizes weathering effects that result in alligatoring or cracking of coal tar films. Volatile Organic Compound (VOC) as supplied is 374 grams/ liter (3.1 lbs./gl.). When thinned 8 % using KOP-COAT Thinner 1000 or 2000, the VOC is 417 gramslliter (3.5 lbs./gl.).

Technical Data: Number of coats: 2 or 3 Volume solids: 59% Theoretical coverage: 946 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 2 mils dry--375 sq.ft./gal.# 3 mils dry--250 sq.ft./gal.# # Allows for 20% application loss. Practical first coat application rate on medium porosity concrete is approximately 200 sq.ft./gal. Film build ratio: Minimum dry film required per coat: 2 to 3 mils Wet film required per coat: 3.4 to 5.1 mils Drying time at 70F. and 50% relative humidity: To touch: 2 to 4 hours Between coats: 12 to 24 hours Prior to use: 24 to 48 hours after topcoat is applied Color: Glossy Black Thinner: Thinning is not normally required except in cold weather or for spray application when 4 pint of KOP-Thinner 1000 per gallon is the maximum amount allowable. Cleaner: Use KOP-COAT Thinner 1000 or Thinner 2000 Surface Preparation: All surfaces must be completely dry before applying BITUMASTIC Black Solution. Primer: Metal or concrete--none Methods of application: Brush, roller, dipping or conventional spray. wet: 100F. Temperature limitations: dry: 400F.

264


KOP-COAT, INC.:

BITUMASTIC C.T.

Urethane-Type I:

A fast curing, two component (1:l volume mix), chemically cured, coal tar urethane coating that combines the known water resistant protection and long term stability of coal tar enamels, with excellent low temperature flexibility and high temperature resistance to flow found in urethanes. It is resistant to chemical and bacteriological attack typically found underground. This coating provides superior electrical insulation to the exterior insulation to the exterior of piping, tanks and structural steel to prevent corrosion and keep the cost of cathodic protection down. For industrial use only. Not intended for use in the home or for potable water service. Although BITUMASTIC C.T. Urethane-Type 1 exhibits selfpriming characteristics, it also functions well over compatible KOP-COAT primers to provide superior corrosion protection. The flexibility and toughness of the coating alleviate problems associated with handling coated items, piling, or tanks. When coated piece is stored above-ground, slight natural chalking will occur. Volatile Organic Compound (VOC) as supplied is 26 grams/ liter (.2 lbs/gl.). No thinning is recommended. Technical Data: Number of coats: One Volume solids: 98% Theoretical Coverage: 1570 mil sq.ft. per gallon. Film build ratio: Minimum dry film required: 10-20 mils depending on service. Typically 15 mils. Wet film required: 10-20 mils. Drying Time at 70F and 50% Relative Humidity: (application temperature llOF) To touch: 4 minutes. Firm to handle: Less than 30 minutes. Recoat: Recoating or repair may be done up to 24 hours without special procedures. Full cure: 48 hours. Color: Black. Component A is Black; Component B is Amber. Thinner: Do Not Thin. Cleaner: KOP-COAT Thinner 2000. Primer: Steel and Ductile Iron: Although normally self-priming, BITUMASTIC C.T. Urethane may be applied over KOP-COAT C.T.U. Low VOC Primer. Concrete: None Temperature limitations: Dry: 15OF Wet: 100F

Kop-Coat, inc.

KOP-COAT, INC.:

265

BITUMASTIC NO. 300-M:

BITUMASTIC No. 300-M is a two-component, self-priming, chemically-cured, catalyzed coal tar epoxy protective coating. For industrial use only. Not intended for use in the home. BITUMASTIC No. 300-M is designed for immersion, interior or exterior exposures and combines the outstanding corrosion resistance characteristics of selected coal tar pitch with those of epoxy resin. Do not use for the interior of dead end, stagnant or very low flow potable water lines. BITUMASTIC No. 300-M is designed to be applied in moderately heavy films for the economical protection of metal, masonry or wood structures exposed to chemical plant environments, water flood gates and dam faces, sewage plants, storage tank linings, bridges, pipeline interiors and exteriors, immersion and atmospheric exposures where a tough, abrasion and chemical resistant film is necessary to insure long-term substrate integrity and strength. No. 300-M can be utilized in every industry including chemical processing, pulp and paper, marine, flood processing, water and sewage, offshore drilling, nuclear energy, textile, petroleum, plating, steel, public utilities, fertilizer, and space facilities. Although 300-M exhibits self-priming characteristics, it also functions well on metal surfaces on which compatible primers and zinc rich primers have been applied. When applied at a minimum of 16 dry mils, it exhibits excellent resistance when immersed in, or subjected to the following environments at ambient temperatures: 1. Chemical Solutions 2. Aliphatic hydrocarbons 3. Acids and alkalis 4. Alcohols It meets or exceeds all the requirements of Corps of Engineers Specification C-200, C-200a, Steel Structures Painting Council Specification SSPC-Paint 16, Steel Tank Institute Corrosion Control System STI-P3 and AWWA specification C-210-84. It can be supplied on order in a version approved for use under Military Specification DOD-P-23236A (SH), Type I, Class 2. Volatile Organic Compound (VOC) as supplied is 252 grams/ liter (2.1 lbs/gl). When thinned 33% to be used as a primer for wood or concrete the VOC is 406 grams/liter (3.4 lbs/gl). Technical Data: Number of coats: Usually 2 or more. Volume solids: 74% Theoretical coverage: 1184 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 90 to 115 sq.ft./gal per coat for two coat applications; 45 to 60 sq.ft./gal for a single multi-pass spray application. Film build ratio: 8 to 10 dry mils (11 to 1 4 wet mils) per coat. Drying time at 70F and 5 0 % relative humidity: To touch: 3-4 hours Between coats: Overnight to 24 hours.


KOP-COAT, INC.:

BITUMASTIC NO. 300-M High Build:

BITUMASTIC NO. 300-M High Build is a version of the BITUMASTIC No. 300-M Coal Tar Epoxy, modified to produce a thicker film in fewer coats. It is self-priming and chemically-cured. One coat can provide up to 30 to 35 dry mils for protection of steel and concrete in extremely corrosive environments. One coat of BITUMASTIC No. 300-M High Build will do the work of two or more coats of conventional coal tar epoxies with significant savings of material and labor costs, while also eliminating the possibility of intercoat delamination. For industrial use only. Not intended for use in the home. On metal, concrete, masonry, or wood where outstanding acid, solvent, alkali, petroleum, or chemical resistance is required. Primarily intended for use in chemical plant environments, sewage paints, storage tank linings, pipeline interiors and exteriors, immersion and atmospheric exposure where a high build, touch, abrasion and chemical resistant film is necessary to insure long term substrate integrity and strength. BITUMASTIC 300-M High Build also conforms with AWWA specification C-210-84, liquid epoxy systems for the interior and exterior of steel water pipelines. BITUMASTIC No. 300-M High Build meets or exceeds all requirements of Corps. of Engineers Specification C-200 and Steel Structures Painting Council Paint Specification SSPC-PT16. Volatile Organic Compound (VOC) as supplied is 250 grams/ liter (2.1 lbs/gl). When thinned 33% to be used as a primer for concrete or wood, the VOC is 406 grams/liter (3.4 lbs/gl). Technical Data: Number of coats: One or more Volume solids: 74% Theoretical coverage: 1185 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 40 sq.ft./gal./ coat at 24 dry mils; 30 sq.ft./gal./coat at 30 dry mils on smooth surfaces (allows for approximate 20% application loss). Film build ratio: Minimum dry film required per coat: 24 mils (normal-30 mils; maximum recommended-40 mils) Wet film required: 32.5 mils for 24 dry mils 40.5 mils for 30 dry mils Drying time at 70F. and 50% Relative Humidity: To touch: 3-4 hours Between coats: Overnight to 40 hours. Before submerging: All chemically cured coatings require a long curing time to reach maximum chemical resistasce. Pot life after mixing: 2 hrs. 50F 10 hrs. 85F 1 hr. 1 OOF 60F 6 hrs. Color: Black Thinner: KOP-COAT Thinner 2000 Cleaner: Use KOP-COAT Cleaner for cleaning equipment. Methods of application: Brush or Spray Temperature limitations: dry: 250F. wet: 120F. maximum

Kop-Coat, Inc.

267

KOP-COAT, INC.: BITUMASTIC SUPER SERVICE Black: A self-priming, heavy-duty, cold-applied, water resistant coating made from pitch derived from suitable tars, selected solvents, mineral fillers and special additives. For industrial use only. Not intended for use in the home. One of its outstanding features is providing a thick film that will protect metal and concrete from severe chemical fumes and corrosive vapors. It has proven especially effective in the sewage industry by protecting metal and concrete against the deteriorating effects of raw and industrial waste materials and hydrogen sulfide gas. It can be used on all all metal and concrete surfaces which will be buried or immersed. It can be used directly on concrete without the need for a separate primer. When exposed to sunlight and effects of weathering, the coating should be aged approximately 2 to 4 weeks, then topcoated with BITUPLASTIC No. 28 or BITUPLASTIC No. 33. This minimizes weathering effects that result in alligatoring or cracking of coal tar films. Do not use for the interior of tanks, containers or pipelines designed for containing potable water. Volatile Organic Compound (VOC) as supplied is 330 grams/ liter (2.8 lbs./gl.). When thinned 15% using KOP-COAT Thinner 1000, the VOC is 411 grams/liter (3.4 lbs./gl.). Technical Data: Number of coats: TWO, minimum Volume solids: 68% Theoretical coverage: 1,090 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 60 to 70 sq.ft.1 gal./coat on smooth metal surfaces. (Allows for approximate 20% application loss.) Concrete surfaces, first coat, 5 0 to 60 sq.ft./gal./coat. (Includes 20% application loss.) coverage will depend on surface profile and porosity. Film build ratio: Minimum dry film required per coat: 12 to 14 mils Wet film required per coat: 18 to 21 mils Drying time at 70F. and 50% relative humidity: To touch: 6 to 12 hours Between coats: 24 to 48 hours Prior to submerging: 14 days after final coat is applied Prior to back-filling and ground burial: 7 days after final coat is applied. Color: Black Thinner: KOP-COAT Thinner 1 0 0 0 . Cleaner: KOP-COAT Thinner 1000 or KOP-COAT Thinner 2000. Surface Preparation: Apply only to clean, dry surfaces. Methods of application: Brush, roller, coventional or airless spray. Temperature limitations: dry: 400F. wet: 120F. Storage life: 1 year minimum


KOP-COAT, INC.:

KOP-COAT Alumimum Epoxy Mastic:

A high solids high build modified epoxy pigmented with aluminum. It is furnished as a two component system with a 1:l volume mix. For industrial use only. Not intended for use in the home. Primarily designed for use over steel which is free of grease and oil and has been suitably prepared by hand or power tool cleaning. Also may be used over rusted and pitted steel when sandblasting is not possible or feasible. It can be applied over aged coatings such as alkyds, oleoresinous, phenolics and epoxies providing that the coatings are soundly adherent. On structural steel, tank exteriors, bridges, fences, metal buildings it can be used as a primer/ topcoat system. KOP-COAT Aluminum Epoxy Mastic may also be used as a primer for epoxy chlorinated rubber, vinyl and polyurethane coatings. KOP-COAT Aluminum Epoxy Mastic demonstrates good resistance to fumes and spillage of solvents, mild salt solutions and moisture. It is not recommended for immersion service. Volatile Organic Compound (VOC) as supplied is 170 grams/ liter (1.4 lbs./gl.). When thinned 5% using KOP-COAT Thinner 2000, the VOC is 204 grams/liter (1.7 lbs./gl.). Technical Data: Number of coats: One or two depending on service use. Volume Solids: 82% Theoretical Coverage: 1315 mils sq.ft./gal. Coverage to achieve minimum dry film thickness: 130 to 150 sq.ft./gal. coat (Allows for an approximate loss of 20%) on smooth surfaces. Film build ratio: Minimum dry film required per coat: 7 to 8 mils Wet film required per coat: 9 to 1 0 mils. Can be applied at up to 16 wet mils per coat. Drying time at 70F and 50% Relative Humidity: 70F: Set to touch: 6 hours Tack free: 16 hours Recoat: 24 hours 80F: Set to touch: 4 hours Tack free: 9-12 hours Recoat: 16 hours Color: Aluminum. Thinners: KOP-COAT Thinner 2000. Cleaners: KOP-COAT Thinner 2000. Methods of Application: Brush, roller, conventional or airless spray. Temperature limitations: Dry: 200F; Wet: 100F.

KopCoat, Inc.

KOP-COAT

269

INC. : KOP-COAT Concrete and Masonry Filler:

A high y fil ed acrylic emulsion coating Used to seal pores of unpainted cinder block, cement block, and rough masonry, both interior and exterior prior to the application of most decorative coatings including emulsions, epoxy emulsions, epoxy ester, rubber-base, urethane, alkyds, and epoxies. Do not use on areas that will be subject to (hydrostatic) back pressure, or for immersion service. Volatile Organic Compound (VOC) as supplied is 1 3 0 grams/ liter (1.1 lbs./gl.). Since this product is thinned with water, the VOC will not change as applied. Technical Data: Number of coats: One or more depending on coarseness of surface and degree of smoothness required. If surface depressions or holes require a thickness of material in excess of 1/16", use multiple applications. Volume solids: 4 1 % Coverage to achieve minimum dry film thickness: 75 to 100 sq.ft./gallon/coat. Drying Time at 70F and 50% relative humidity: To touch: 1 to 2 hours To recoat: 4 to 6 hours To topcoat: Overnight At temperatures below 70F. and humidities above 508, an increase in dry time will be required. Color: Off-white Thinner: Potable water. Material comes ready to use but if can is left open and filler becomes too heavy for application, a small quantity of water may be added to restore original consistency. Cleaner: Potable water, soap and water. Surface preparation: Surface must be free of all dirt, oil, loose particles and other foreign matter. Dampen surface slightly before application. Primer: None Methods of application: Brush, roller, conventional air spray or airless spray. For spraying, thin up to 2 0 % with water if necessary. Do not apply to surfaces with temperatures below 40F, or if rain is expected before the filler dries. If a smoother finish is desired use a window squeegee over a freshly applied, small area of filler returning excess filler to container. Do not let filler dry too long before using squeegee.


KOP-COAT, INC.:

KOP-COAT P-1500 Inorganic Zinc:

A two-component, water-based, self-curing, pure inorganic zinc-rich coating. KOP-COAT P-1500 Inorganic Zinc is a high performance coating employing high purity, ultra-small particle zinc metal dispersed in a selected metallic silicate. Although the dried coating shows porosity of typical inorganic zincs, the pore size is extremely small in comparison. For industrial use only. Not intended for use in the home. On steel surfaces, submerged or nonsubmerged, subject to severe weathering or high salt concentrations, such as bridges, ballast tanks, offshore platforms, cargo holds, piping, storage and process tanks. Has excellent abrasion, temperature, and weather resistance, as well as complete resistance to aliphatic hydrocarbons (oil), aromatic hydrocarbons (toluol and xylol), alcohols, ketones, and esters. Protects cathodically and serves as "permanent" primer for coatings that will be subject to chemical exposure. Can be topcoated with vinyls, epoxies, acrylics, alkyds, and certain coal tar coatings. An intermediate coating may be needed. Do not use in areas subject to splash or spillage of acid or alkali solutions, or for complete immersion in these solutions outside a pH range of 5 to 9. P-1500 Inorganic Zinc meets or exceeds all requirements of Military Specification MIL-P-23236, Type I! Class 3. VOC Organic Compound (VOC) as supplied is 0. No thinning is recommended. Technical Data: Weight per gallon: 27.71 pounds(mixed)-liquid-6.46 pounds net powder-21 -25 pounds net Solids content: Average-82+1% by weight % zinc in dry applied film: 94*1% Viscosity (Stormer): 70+2 KU Flash Point: None (non-flashing) Color: Gray Shelf life: 1 year minimum Pot life: 16 hours Service temperature limits: dry: 800F. wet: 130F. Number of coats: One Dry film recommended: 2 mils minimum (4.9 mils wet) to 3 mils (7.5 mils wet) Maximum dry film: Do not exceed 4 to 4.5 dry mils (10 to 1 1 wet mils). Theoretical coverage to achieve dry film thickness: 220 to 330 sq.ft./gallon Conditions for use and curing: Temperature-40-140F. Relative humidity-0-90% Important-Do not apply if rain is expected within six hours Thinner: Clean water, but thinning is not normally recommended Application: Brushing of large surfaces should be avoided.

Kop-Coat, lnc.

KOP-COAT, INC.:

271

KOP-COAT 40 PASSIVATOR:

A two-component wash primer formulated with a zinc chromate

pigmented polyvinyl butyral resin and phQSphQric acid. For industrial use only. Not intended for use in the home. Pretreatment for non-ferrous metals prior to priming. May also be used on blasted clean steel surfaces with some vinyl coating systems. Also suitable for use on galvanized metal prior to application of primers except KOP-COAT P-1500 Inorganic Zinc and similar zinc primers. Volatile Organic Compound (VOC) as supplied is 745 grams/ liter (6.2 lbs./gl.).

Technical Data: Number of coats: One Volume solids: 10.2% Theoretical coverage: 163 mil sq.ft./gal. Coverage to achieve dry film thickness of 0.4 mils: 325 sq.ft. (allows for an approximate loss of 20%) Film build ratio: Dry film required: 0.3-0.5 mils (must never exceed 0.5) Wet film required: 3.0-4.9 mils Drying time at 70F. and 50% relative humidity: To touch: 15 minutes To topcoat: 1 hour minimum; must be recoated within 24-48 hours; allow 8 hours before topcoating with an epoxy. Color: Greenish grey liquid; a mottled, semitransparent greenbrown dry film is normal. It will not completely hide or develop a uniform color on the surface. Thinner: KOP-COAT Thinner 1 5 0 0 Cleaner: XOP-COAT Thinner 1500 Surface Preparation: Nonferrous and galvanized metals: Degrease with KOP-COAT Thinner 2000. Steel: Surface must be dry and free of dirt, oil and grease. All mill scale, rust and other interference materials must be completely removed by sandblasting or pickling. Sandblasted surfaces should be coated the same day they are cleaned. Methods of application: Brush, roller, conventional or airless spray, dip or swab. Temperature limitations: dry: 150F. wet: 100F. Storage life: 18 months minimum Pot life: 8 hours

272


KOP-COAT, INC.:

KOP-COAT 340 Gold Primer:

A high solids, high build, durable, chemical-resistant universal primer. It is based on a polyamide-cured epoxy resin, and shipped as a two-component system. Mix ratio is 1:l by volume. For industrial use only. Not intended for use in the home. A s a primer for metal, with a neutral high contrast color and a designed-in surface texture, for use in shop and field, that can be topcoated up to one year after application with epoxies, urethanes, alkyds and emulsions. Volatile Organic Compounds: Components A And B as supplied and mixed--2.45 lbs./gal. (294 grams/liter). When thinned 8% by volume using Thinner 2000--2.84 lbs./gal. (340 grams/liter). Technical Data: Number of coats: One Volume solids: 66% Theoretical coverage: 1055 mil sq.ft./gal. Coverage to achieve film thickness: sq.ft./gal.coat: (allows for an approximate loss of 20%) 420: Wet film thickness mils: 3 Dry film thickness mils: 2 210: Wet film thickness mils: 6 Dry film thickness mils: 4 140: Wet film thickness mils: 9 Dry film thickness mils: 6 Drying time at 50% relative humidity and: 60F: To touch: 3 to 4 hours To topcoat: 12 to 16 hours 75F: To touch: 2 hours To topcoat: 6 hours 9OF: To touch: 1 hour To topcoat: 4 hours Color: Yellow-Gold Thinners: KOP-COAT Thinner 2000 Cleaner: XOP-COAT Cleaner 2300 Surface preparation: Surface must be dry and free of dirt, oil and grease or other foreign contaminants. Steel: All mill scale and foreign matter must be removed by abrasive blasting. Galvanized and Non-Ferrous Metals: Degrease, then treat galvanized and non-ferrous metal surfaces with KOP-COAT 40 Passivator. Methods of application: Brush, roller, air-atomized or airless spray. Temperature limitations: dry: 250F wet: 120F Storage life: One year Pot life: 10 hours at room temperatures, at higher temperatures, pot life is shortened.

Kop-Coat, lnc.

KOP-COAT, INC.:

273

KOP-COAT 610 Acrylic Emulsion:

Alkyd-modified acrylic emulsion. On new or previously painted non-submerged exterior surfaces where excellent resistance to weathering, chalking, fading and discoloration are required. Alkyd modification upgrades adhesion on previously painted surfaces that show moderate chalking. Its improved leveling properties significantly enhance its exterior appearance and improve its resistance to dirt pickup. Maximum performance and durability are obtained with 2 coats applied to a total of 3 mils dry. Volatile Organic Compound (VOC) as supplied is 170 grams/ liter (1.4 lbs./gl.). Since this product is thinned with water, the VOC will not change as applied. Technical Data: Number of coats: One or two Volume solids: 42% Theoretical coverage: 675 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 350 sq.ft./ coat (allows for 20% loss) on smooth surfaces. Actual coverage will depend on surface profile and porosity. Film build ratio: Minimum dry film required per coat: 1.5 mils Wet film required per coat: 3.6 mils Drying time at 70F. and 50% relative humidity: To touch: 1 5 minutes Between coats: 1 to 2 hours Colors: Color chart 560, flat Thinner: Clean potable water. Cleaner: Water; soap and water. Dispose of cleanup water according to local applicable regulations. Do not dispose of coating or cleanup water in any public or private body of water. Surface preparation: Previously painted surfaces, as well as bare surfaces, must be free of excessive chalk, dirt, oil and other foreign matter. Primers: Steel, Shop or Field: KOPCOAT 622LCF Primer or KOP COAT 340 Gold Primer. Galvanized and nonferrous metals: Degrease, then apply KOP COAT 40 Passivator. Wood: Thin first coat of KOPCOAT 610 10 to 15% with clean water. Methods of application: Brush, roller, conventional or airless spray. Do not apply to surfaces that will be exposed to rain before coating is dry, or on surfaces with temperatures below 40F. Temperature limitations: Dfy: 150F. Storage life: 1 8 month minimum Pot life: Not applicable, single component


KOP-COAT, INC.:

KOP-COAT 620 Acrylic Emulsion:

High sheen (semi-gloss) acrylic emulsion For industrial use only. Not intended for use in the home. On interior and exterior concrete, stucco, cement and cinder block, brick, wood and metal surfaces. Provides tough, durable, easy-to-clean finish with excellent weathering properties. Unaffected by intense sunlight and high humidity. Levels well and dries quickly. Can be applied to damp surfaces and over previously painted surfaces. Volatile Organic Compound (VOC) as supplied is 3 1 0 grams/ liter (2.6 lbs./gl.). Since this product is thinned with water, the VOC will not change as applied. Technical Data: Number of coats: Two Volume solids: 35% Theoretical coverage: 560 mil sq.ft./gal. Coverage to achieve minimum dry film thickness: 3 0 0 sq.ft./gal./ coat (allows for a greater than 20% loss). Actual coverage on concrete and masonry will depend on profile and porosity. Film build ratio: Minimum dry film required per coat: 1.5 mils Wet film required per coat: 4.2 mils Drying time at 70F. and 50% relative humidity: To touch: 1 hour Between coats: 4 hours Color: Color Chart 560 pastel colors Thinner: Potable water Cleaner: Potable water, soap and water. Dispose of clean-up water according to local applicable regulations. Do not dispose of coating or clean-up water in any public or private body of water. Surface preparation: Previously primed or painted surfaces, as well as bare surfaces must be free of all dirt, chalk, oil or other foreign matter. Primer: Metal: Steel, Shop and Field: KOP-COAT 622-LCF or KOPCOAT 340 Gold Primer or a KOP-COAT Zinc-Rich Primer. Galvanized and non-ferrous metals: First degrease, then prime with KOP-COAT 40 Passivator. Masonry: Surfaces with large pores, such as coarse cinder block and cellular concrete materials should first receive one or more coats as needed of KOP-COAT Concrete & Masonry Filler. Wood: Thin first coat of KOP-COAT 620 Acrylic Emulsion by 1 0 to 1 5 % with water. Methods of application: Brush, roller, air or airless spray. Add sufficient water for proper atomization. Do not apply to surfaces that will be exposed to rain before the coating is dry or on surfaces with temperatures below 40F. Temperature limitations: Dry: 15OF. Storage life: 1 8 months minimum.

Kop-Coat, lnc.

KOP-COAT, INC.:

275

KOP-COAT 622-LCF Primer:

Lead-free and chromium-free medium oil alkyd primer. Contains calcium borosilicate for excellent rust-inhibitive effect. For industrial use only. Not intended for use in the home. KOP-COAT 622-LCF offers several advantages over standard alkyd primers: 1. Excellent rust-inhibitive properties without the use of lead or chromium compounds. 2. Full compliance as supplied with current and proposed air pollution regulations. 3. High solids for economical coverage. 4. Very good brushability as supplied for use where spray application is restricted. 5. Quick drying for early handling and topcoating. 6. Will accept topcoating for up to one year after application. Use KOP-COAT 622-LCF in shop and field on all steel and nonferrous metal surfaces for non-submerged service. Can be topcoated with alkyds, epoxy esters and other “oleoresinous“ coatings, and with emulsion coatings. Allowed extra time to dry (3 to 5 days), 622-LCF can be used for spot-priming when weathered alkyd finishes are being “up-graded’‘with KOP-COAT 1122-BRS Polyurethane. Volatile Organic Compound (VOC) as supplied is 420 grams/ liter (3.5 lbs/gl). Thinning is not recommended. Technical Data: Number of coats: One Volume solids: 50% Theoretical Coverage: 800 mil sq.ft./gallon Recommended Dry Film Thickness: minimum 1.5 mils (3 wet mils) maximum 4 mils ( 8 wet mils) Practical Coverage Rate: (allows for approximate 20% application loss). 425 sq.ft./gallon at 1.5 dry mils. 160 sq.ft./gallon at 4 dry mils. Drying Time at 70F and 50% Relative Humidity: at 1.5 to 2.0 mil rate: To touch: 30 minutes To handle/topcoat: 1 hour at 3 to 4 mil rate: To touch: 60 minutes To handle/topcoat: 24 hours Color: Dark Brown Thinner: KOP-COAT Thinner 4000 Cleaner: KOP-COAT Thinner 4000 Surface Preparation: Steel: New steel, in shop: Degrease In shop or field, on rusted surfaces: Abrasive-blast Stainless Steel and non-ferrous metals: Degrease and pretreat with KOP-COAT 40 PASSIVATOR.

276

Prepaint Specialtim and Surface Tolerant Coatings

LION OIL CO.:

LION D200 Elastomeric Sealant:

LION D200 elastomeric sealant is a two-component, cold-applied formulation of asphalt and urethane. After the components are mixed, a chemical reaction in situ forms an elastomeric polymer with numerous excellent properties and a 20 year life expectancy. Basic Use: LION D200 elastomeric sealant is designed as an expansion joint sealant having a bond of maximum strength. Its properties give it a wide range of uses, as follows: 1. Where structural movement due to temperature change and mechanical stress is expected, it forms a tough, adhesive bond that stretches and recovers. 2. Where adhesion to more than one construction material is desired. Example: between bridge decks where one side is concrete, the other metal. It bonds to concrete, metals, masonry, wood, glass and most plastic materials including urethane insulation. 3 . Where a waterproof seal is needed. Below grade, or in marine locations, for example. Moisture vapor transmission is minimal. It is immune to bacterial attack. 4 . Where heavy, periodic mechanical abrasion is expected. Example: plant floors, highway joints. 5. Exterior and interior applications. This sealant is weatherproof because it is asphalt based. 6. Where extremely low temperatures will be encountered. Service temperature range is -80F to 200F. 7. In industrial atmospheres. Resistance to acids, alkalis and salts is excellent. 8. In horizontal and low sloped joints. Composition and Materials: LION D200 elastomeric sealant is formed by chemical reaction after the two-components are mixed. Component 1 is the base. It consists of elastomer-forming polymers modified with an asphalt plasticizer. Selected fillers and stabilizers are added to maximize strength and prolong shelf life. Component 2 consists of the curing agent and polymer extenders. Applicable Standards: LION D200 sealant meets or exceeds federal standards for Sealing Compound, Cold-Application Mastic, Multiple Component Type, for joints in concrete, and ASTM-D-1850 entitled Concrete Joint Sealer, Cold Application Type, Single or Multiple Component. Technical Data: LION D200 sealant is nearly 1 0 0 % elastomeric. Adhesion to all major substrates under a varity of stresses is excellent. Desirable properties are retained in the face of moisture weathering, abrasion and other destructive forces over a 20 year life expectancy.

Lion Oil Co. 277

LION OIL CO.: Sealant:

LION D203 Two-Component Elastomeric Vertical Joint

LION D203 is a two-component elastomeric compound of asphalt and polymers formulated for mixing and applying at ambient temperature. Basic Use: LION D203 elastomeric vertical joint sealant is designed as an expansion and construction joint sealant having a bond of maximum strength. Where structure movement due to temperature change and mechanical stress is expected, it forms a tough, adhesive bond that stretches and recovers. It has excellent adhesion to concrete, metal and wood, and due to its unusual low temperature properties, is ideal for use in extreme cold environments. Composition and Materials: LION D203 is a two-component elastomeric compound of asphalt and polymers. Technical Data: Application Temperatures Range, F: 60 to 90 Flash Point, Pensky Martens Closed Cup, Min.: 100 Solids, weight % Min.: 83.7 Weight, lbs./gal (approx.): 8.65 Flow of Cured Film at 200F: None Cracking or disbonding of 1/16-inch cured film on steel, 140F to -60F: None Tensile strength @ 74F, PSI: 85 Elongation @ 74F, %: 172 Bond Strength (to steel), PSI: 135 Shear Strength: (1 Month Cure): Tensile, PSI: 52 Compression, PSI: 35 Moisture Vapor Transmission, Perm Inch (ASTM E-96, Method E): 0.0048 Service Temperature Range, F: -80 to 200 Resistance to Abrasion by Sandblast: Excellent Resistance to Oils, Greases, Solvents: Poor


LION OIL

-

CO.:

NOKORODE LION SP ASPHALT:

Primer

LION NOKORODE SP Asphalt, an asphalt-solvent blend for spray or brush application, is recommended as a prime coat on porous surfaces prior to application of the mastic type of protective coatings as LION NOKORODE SEAL-KOTES, and other LION NOKORODE coatings. The thin bodied SP Asphalt penetrates and after curing improves the cohesion between weakly-bonded particles and provides a firm surface to which heavier compounds can bond. LION NOKORODE SP Asphalt is an excellent black coating with good hiding power and is recommended for covering weathered vapor seals to rehabilitate and restore their appearance, and as a general purpose asphaltum solution. Typical Properties: Flash, Pensky-Martens, closed cup, min.: 100F Dry to touch at 77F, approximately: 10 minutes Consistency: Spray or brush Solids content: 40% Lbs./gal. at 60F. approximately: 7.3 Application and Coverage: Surfaces should be dry, free of oil and grease, and in properly prepared condition for coating. LION NOKORODE SP Asphalt has penetrating properties and will bond to a layer of rust or scale, but the bond will be no stronger than that of the rust or scale to the metal. Badly corroded surfaces, loose paint, mill scale, should be cleaned by sandblasting, chipping, scraping, wire-brushing, or burning, with sandblasting preferred where feasible. Apply by spray gun or brush. In cold weather below 40F, if thinning is necessary, add not more than one volume in 2 0 mineral spirits preferably boiling in the range of 305/360F. NOKORODE SP Asphalt should not be applied to vertical surfaces with operating temperatures in excess of 125F. Note: SP Asphalt is not recommended as a primer, prior to application of NOKORODE K-KOTE. Uses: For application as a prime coat to porous or rough surfaces prior to application of LION NOKORODE SEAL-KOTES and other asphalt base protective coatings; as an asphalt base coating to offer an efficient and economical protective film below vapor and moisture barrier coatings.

Lion Oil Co.

LION OIL CO.:

279

NOKORODE LION 331:

- Insulation adhesive - Insulation weather barrier

Description: LION NOKORODE 331 is a non-fibrated asphalt emulsion, available in one consistency suitable for application by brush, roller, or spray. Uses : - as a prime and base coat for insulation in cold storage vaults and other low temperature insulated construction as well as ambient temperature applications. - as a bond coat for cementing layers of vapor barrier sheets and aluminum foil to walls and ceilings. - as a weather coat for protection of thermal insulation in high temperature service. It is highly resistant to chemical liquids and fumes such as would be encountered around chemical plants and refineries. The "breathing" characteristics of LION NOKORODE 331 permit it to expel moisture vapor in hot service. Application: LION NOKORODE 331 should not be applied below 50F ambient temperature or stored where freezing temperatures are anticipated. For best results as a coating, a fabric membrane should be used between coats of mastic. These membranes reinforce the coating and improve its resistance to mechanical abuse. LION NOKORODE 331 is nonflammable and presents no hazard from open flames or welding being done in the work area. Clean up may be accomplished with fresh water before mastic dries. After mastic dries, use mineral spirits for clean up. Coverage : One ( 1 ) gallon per 1 0 0 sq.ft. for priming. Two ( 2 ) gallons per 1 0 0 sq.ft. for bonding vapor barrier sheets. Four ( 4 ) gallons per 1 0 0 sq.ft. for bonding insulation or a metal coating. Six (6) gallons per 1 0 0 sq.ft. as a roof coating applied in two coats using glass membrane. Typical Properties: Weight, lbs./gal.: 8.5 Solids content, % by weight: 5 0 Dry time, hours: 4-6 Consistencies: Brush, roller and spray Recommended service temperature range, F: 20-200 Miscibility: Can be diluted with water. Chemical stability: Can be mixed with cement. Storage stability#: Will not settle in containers. # This material can be protected from freezing in transit

by addition of alcohol at additional cost.


LOCl'ITE CORP.:

EXTEND Rust Treatment:

A one-step rust treatment that converts rust to a tough coating in 1 0 minutes. No primers or sandblasting required, simply wirebrush parts. Two to three coats of EXTEND will resist normal environments for up to 5 years; for severe environments or maximum protection, apply topcoat over EXTEND. Can be applied with brush or spray. Resists temperatures to 250F. Fights rust on: - Pipes, valves, fittings in refineries, tankers, power plants, domestic and commercial heating/cooling plants. - Truck trailers, storage tanks - Fences, guard rails, conveyors - Overhead cranes, booms, floor gratings, ducts - Outdoor advertising sign supports, municipal and highway sign posts and frames - Bulkheads, overheads, decks, hatch covers, stacks on ships (topcoat with marine paint) - Agricultural equipment, harvesters, plows, discs, tractors, corn pickers, etc. Snow removal equipment

-

LPS Laboratories, lnc.

281

LPS LABORATORIES, INC.: LPS COLD GALVANIZE:

-

-

Prevents rust and corrosion Lasts up to 3 years Heat resistant, zinc coating Works as a primer Can be applied to rusted surfaces

LPS COLD GALVANIZE is a zinc-rich coating that performs like a hot-dip galvanize to prevent rust and corrosion on all types of metals for up to three years. It can be used as a primer over rusted metal to repair hot-dip galvanizing. Withstands temperatures up to 750F., dry heat up to 1000F. and water temperature up to the boiling point. Typical Industries that use LPS Cold Galvanize include: - Manufacturing - Construction - Automotive - Heating and plumbing - Air conditioning and refrigeration - Agriculture - Home LPS COLD GALVANIZE forms a zinc-rich coating which electrochemically binds itself to metal surfaces to protect them for up to three years. Its an ideal coating for the prevention of rust and corrosion on metals. Its heat resistant properties make it ideal for use in high temperature locations. LPS COLD GALVANIZE can be used on new metal or on rusted metal where the loose rust scale has been removed. Formulation: 95% zinc-rich coating with alkyd resin binders, solvents and selected additives. Properties: Thickness--Single Application: 1.5 mils Coverage: Approximately 50 square feet per pound Touch Dry: 5 minutes (aerosol) Repaint Time: 6 hours air dried 30 minutes when baked at 350F. for 15 minutes Withstands: Water temperature above boiling Continuous dry heat up to 750F. Short period heat up to 1,000F. Specifications Meets or exceeds these specifications: MIL P-46105 weld thru primer USN MIL-P-21035 USAF MIL-P-26915A for steel USAF MIL-T-26433 for towers temperate and arctic zones Passes Preece Test for hot-dip galvanizing


LPS LABORATORIES, INC.:

-

LPS3 Heavy-Duty Rust Inhibitor:

Forms heavy, waxy film to resist moisture, sand, dirt, dust, and vibration Heavy-duty chain lubricant and anti-seize coating Outdoor rust and corrosion protection under severe weather conditions for up to two years Stops exfoliation or filiform corrosion of aluminum Safe on rubber, paint and plastic Contains no chlorinated solvents

Uses : Protects: equipment from corrosive elements; metal parts and equipment in storage; machinery and equipment in storage; machinery and equipment during overseas and domestic shipments; salt spreading equipment and snow plows; hitches, shackles, fittings; and also the outside of bilge pumps. Lubricates: chains; cables; pulleys; open gears, springs, hoists, wire rope; pumps; ball joints Inhibits Corrosion: on car doors and rocker panels; battery terminels, brackets, cables and connectors; coils and cable ends Seals Out Moisture & Corrosive Elements: from electrical panel boxes and housings; electrical circuits and connectors Specifications: Meets or exceeds the following specifications: MIL C-23411A MIL C-l6173D-Grade 2 MIL C-81309D Type I1 Conforms to SAE AMS 3066, BMS 3-23, DMS-2150 Approved by USDA for use in food plants Properties: Film Thickness: .002 inches of waxy film Specific Gravity: .830 approximately Flash Point: 112 degrees F. T.C.C. % Non-Volatiles (ASTM-D-1644-75): 25% Viscosity at 100 degrees F: 48 centipoises approximately Boiling Point: 300 degrees F. approximately Vapor Pressure: 2.0 (nun Hg) Dissipation Factor: -005 Dielectric Strength and Breakdown Voltage (ASTM-D-877-23): 0.1" gap. 35 kilovolts Humidity Cabinet Test: No rust on steel panels after 100 days Salt Spray Cabinet Test: No rust on steel panels after 550 hours Propellant: Carbon dioxide

LPS Laboratories, lnc.


283

LPS INSTANT COLD GALVANIZE:

95% zinc rich heat resistant (non-paint) coating stops rust and corrosion Repairs rusted, galvanized and welded surfaces by electrochemically fusing with bare metal Protects up to three years--will not yellow, chalk, crack or peel. Can be used as a primer or left as gray matte finish coat Works well on all metals Works on rusted surfaces Uses alkyd binders to prevent deterioration caused by sunlight and radiation Uses : Protects & Prolongs Life of: outside storage tanks, bins, towers, light standards and chain link fences; mufflers, exhaust pipes, gas tanks, U-bolts, wheel rims & frames; compressors & material handling equipment; plumbing, heating air conditioning parts; outdoor electrical equipment Inhibits Rust on: structural steel & wrought iron; ducts; fan blades, pulley & chain covers; machine housings & newly welded surfaces; exposed conduit threads Specifications: Meets or exceeds these specifications: MIL-P-46105 weld thru primer USN MIL-P-21035 USAF MIL-P-26915 for steel USAF MIL-T-26433 for towers in temperate and arctic zones Passes Preece Test for hot dip galvanizing Approved by USDA for use in food plants Properties: Film Thickness (after single application): 1.5 mils Coverage: Approximately 50 square feet per pound Touch Dry: 5 minutes with aerosol Repaint Time: 6 hours air dried 30 minutes when baked at 350 degrees F. for 15 minutes Withstands: water temperature above boiling continuous dry heat up to 750 degrees F. short period heat up to 1,000 degrees F. Propellant: Hydrocarbon

&


284


-

-

LPS Paint and Gasket Remover:

Removes adhesives, decals, tape and carbon deposits Strips paint, varnish and tape from wood, metal and concrete in minutes Lifts gaskets from valves, pipes and engine components in minutes Penetrates crevices and molding Fast acting

Uses : Removes: acrylic, adhesive, alkyd, carbon deposits, decals, enamel, epoxy, gaskets, shellac, tape, urethane and varnish Properties: Volatiles: 98% by weight Solvents: Chlorinated Acid: None Alkali: None Contains methylene chloride Propellant: Hydrocarbon

Mantrose-Hawser Co.

MANTROSE-HAEUSER CO.:

285

Galvanized Metal Primer:

Enhances the Appearance of Galvanized Surfaces Galvanized Metal Primer is a specially formulatzd coating that adds life to new and aged galvanized surfaces while it improves appearance. Contains a vinyl copolymer resin that imparts its heavy cling characteristics, and which also provides an excellent base for other types and shades of coatings. Galvanized Metal Primer virtually etches into the metal surface on application because of its chemical properties.

-

For interior or exterior use. Recommended for gutters, downspouts, eaves, decks, or decorative galvanized objects. Holds up under severe weather conditions. Use as a finished coat; can be tinted with Universal Tinting Colors. Ready for repainting in two hours. Helps prevent drying and peeling and other effects of the elements. A water-thinned vinyl resin primer coating that cleans up easily with warm, soapy water.

-

HIDE 'N SEAL Quick-Dry, Oil-Based, All-Purpose Primer for Super Stain Sealing: Versatile primer and sealer for interiors and exteriors can be used on any clean, dry surface, either bare or previously coated: wood, drywall, plaster, trim, metal, galvanized metal, aluminum. Seals porous surfaces and knots, and prevents bleeding of colors.

-

-

For interior and exterior use. Primes and seals bare or previously coated surfaces. Excellent base for wall covering or paint. Locks in tannin (cedar and redwood), most inks, ballpoint and felt marker stains. White pigmented, oil based, can be tinted with Universal Tinting Colors. Apply with brush, roller or spray. Provides excellent enamel hold-out. For more difficult stains, use shellac-based ENAMELAC.


MANTROSE-HAEUSER CO.: Stain-Killer:

MAXHIDE Water-Based Primer, Sealer,

MAXHIDE is a scientifically-formulated, water-based primer, sealer and stain-killer that prepares all surfaces for the application of paint. With a MAXHIDE undercoat, all paint jobs look better, wear longer and cost less. Eases and speeds work as it simplifies difficult painting problems. And it's waterbased for easy use and easy cleanup. MAXHIDE primes bare and previously painted wood, drywall, plaster and trim, providing excellent enamel hold-out. MAXHIDE seals porous surfaces, drywall, plaster, ceiling tiles, masonry, old wallpaper, knots and bleeding colors. MAXHIDE kills stains such as tannin (cedar and redwood), rust, and most ink, ballpoint and felt marking stains. For exceptionally difficult stains, use shellac-based flat white ENAMELAC (interior) or HIDE'N SEAL (interor and exterior).

-

Dries fast Outstanding adhesion to glossy and other surfaces--indoors or out. Easy to use--requires no special thinner. Cleans up with soap and water. Effectively blocks troublesome stains such as rust, crayon, grease and tannin bleed. Can be recoated in less than an hour.

ENAMELAC Flat White, Shellac-Based Primer, Sealer, Stain-Killer: Primes, seals, kills stains with a single coat, with no surface preparation. Can be applied to porous or non-porous materials such as wood, drywall, ceiling tile, masonry, wood knots, and bleeding colors. Sticks to glass firmly and will not scrape off.

-

For interior or exterior use. Neutralizes tannin (cedar and redwood); prevents alkali from bleeding through new plaster and masonry. Covers most inks, ballpoint and felt marker stains, and wallpaper designs (no need to remove paper before coating). Seals knots, sappy areas, and bleeding stains on wood. Resists rust stains--ideal base coat for all metals. White pigmented--can be tinted with Universal Tinting Colors. Dries quickly--can be recoated in 4 5 minutes.

Mantrose-Haeuser Go.

287

MANTROSE-HAEUSER CO.: READY PATCH Ready-to-Use Spackling and Patching Compound: READY PATCH is a scientifically formulated patching and spackling compound, ready-to-use directly from the container. Requires no mixing or additives. Applies firmly, with a single swipe, to any interior and most exterior surfaces. Use with a spatula, putty knife, trowel or caulking gun and get professional results with unequaled ease and speed. Versatile Indoors and Out: - Fills and smooths plaster cracks, nail holes, woodwork splits and blemishes, wallboard joints, cracks and seams around window frames and moldings, with professional results. Adheres firmly to any clean, dry surface; ideal for plaster, wood, wallboard, brick and concrete. - Doesn't get rubbery or gummy. Dries quickly. Sands easily. Requires no priming. Neutral under all paints and coatings.

-

READY PATCH LITE Professional Spackling and Patching Compound: Won't dry in the container New READY PATCH LITE is the answer to every do-it-yourselfer's dream! It has been scientifically formulated so that it won't dry out in the container...no matter how long you keep it. Apply with a putty knife, trowel, spatula, or caulking gun. You'll get professional results with a single swipe. Fast and easy to use on any interior surface, and most exterior surfaces, as well.

-

Keep container covered and READY PATCH LITE will maintain its original consistency indefinitely. Can be used indoors and out. Ready to use - nothing to add. ..nothing to mix. Ideal for filling and smoothing wallboard joints, cracks and seams around window frames and moldings, nail holes, plaster cracks, and woodwork blemishes. Use on wallboard, wood, plaster, brick and concrete. READY PATCH LITE adheres firmly to any clean, dry surface. No priming necessary. Won't get gummy or rubbery. Dries fast. Sands easily.

288


MANTROSE-HAEUSER CO.:

SANDING WOOD SEALER:

Clear Satin Finish Dries Quickly--Sands Easily--Seals Completely Brush or spray SANDING WOOD SEALER for a clear coat, undercoat or first coat for varnish, on any surface where a seal is required. Ideal for use on all types of unfinished interior wood surfaces, including plywood. Seals the wood completely, sands easily, and dries quickly. Does not gum sandpaper. Adds richness and depth to the natural beauty of wood grain, or to the stain over which it is applied.

-

Versatile--Lays on as a clear coat, undercoat, or primary coat before varnishing on interior or exterior wood surfaces. Has no objectionable or irritating odor. Dries quickly, completely, and sands easily. Doesn't gum sandpaper. Solvent-based--clean brushes, rollers and spray equipment with mineral spirits (sub turps). Wallcovering Preparations:

SUPER SIZE: A methyl cellulose wall sealer specially formulated to prepare walls for wallcoverings - Works well with all types of adhesive - Mold and mildew resistant May be used on new, unpainted, or old painted walls

-

SURE-SIZE: A methyl cellulose wall size formulated especially for pre-pasted wallcoverings - Easy to use - Seals walls prior to hanging pre-pasted wallcoverings SURE-PRIME: Acrylic SURE-PRIME is the perfect primer and adhesive enhancer, ready to use for hard-to-hang surfaces. - An excellent wallcovering undercoater - Ideal as an adhesive enhancer for such hard-to-hang surfaces as existing vinyl, foil and mylar wallcoverings, paneling, and gloss and semi-gloss paints

McGean-Rohco,Inc.

MCGEAN-ROHCO, INC.:

289

INTERLOX Iron Phosphate Systems:

Iron Phosphating--Spray: INTERLOX Compound AT-3-FSP: Powdered, low temperature iron phosphating compound. Contains some detergency and can also be augmented with INTERLOX Additive CA-3-LT to meet various soil conditions. (70-130F.) INTERLOX Compound AT-2-FSL: Liquid, low temperature iron phosphating compound for use with INTERLOX CA-3-LT. (70-130F.) INTERLOX Compound 2324 FSP: Low temperature, powdered iron phosphate. Designed as aqueous spray for good paint adhesion on steel or aluminum. For threeor five-stage washers (120-150F.) INTERLOX Compound IS-1-FSL: Liquid iron phosphate for cleaning and phosphating steel, aluminum and zinc-based die cast metals where rinses are not practical. Used with INTERLOX CA-1. FORD M# M5B175A. Coating weight: 25-40 mg/sq.ft. INTERLOX Compound IS-RT-3-FSP: Powdered cleaning and iron phosphating compound. Designed as low temperature spray iron phosphate for good paint adhesion on steel or aluminum. Used with either INTERLOX CA-1 or CA-3. INTERLOX Compound 820-FSL: Concentrated liquid iron phosphate fortified with accelerators. Gives good paint adhesion on steel, aluminum or galvanized metals. Suited for automotive and appliance ware. Iron Phosphating--Immersion: INTERLOX Compound ID-3-FIP: Immersion iron phosphate designed for cleaning and phosphating in 5-tank soak lines. Produces a fine, blue, densely packed coating. (120-1 50F. ) INTERLOX Compound IR-D-FIL: Liquid iron phosphate with simultaneous cleaning, rust and scale removal and phosphate coating. (Room temp. -160F.) Ford M# M5B253.

290


MCGEAN-ROHCO, INC.:

INTERLOX Iron Phosphate Systems(C0ntinued):

Iron Phosphating--Auxiliary: INTERLOX Compound I-WO: Liquid, wipe-on/wipe-off, iron phosphate. Cleans, removes rust and scale, and deposits a phosphate coating by manual application on all metals. (70-85F.) INTERLOX Additive CA-1-HT: Liquid cleaning additive for use with INTERLOX IS-1, IS-RT to increase wetting and removal of soil. Speeds cleaning of stubborn soils in short cycles. (120-170F.) INTERLOX Additive CA-3-LT: Liquid cleaner additive to supplement low and medium temperature iron phosphate systems. Cleaning medium for INTERLOX AT-2 and AT-3. (70-130F.) Addition Agent 248: Liquid detergent component for INTERLOX ID-3 or INTERLOX IR-D to improve wetting and drainage of solution. Ford M #M5B105.

McGean-Rohco, lnc.

291

MCGEAN-ROHCO, INC.: INTERLOX Zinc Phosphate Systems: Zinc Phosphating--Immersion: INTERLOX Phosphate 906-ZIL: Macro-crystalline zinc phosphate coating specifically designed for ferrous surfaces. Can absorb organic, water-displacing, and wax coatings. Excellent iron tolerance. Meets or exceeds GM 4435, Ford S-2, Chrysler PS-80 specifications. INTERLOX Phosphate 2325 MCIZ: Micro-crystalline zinc phosphate coating with built-in accelerators to eliminate two-step process. FOP prepaint systems on ferrous surfaces, zinc-plated or galvanized substrates. Produces smooth coatings with weights up to 400 mg/sq.ft. Zinc Phosphating--Spray: INTERLOX Phosphate S-200-ZCR: Micro-crystalline zinc phosphate coating for steel. Excellent quality; easy to control with little sludge formation. Subsequent paint provides humidity and detergent resistance, as well as good adhesion and flexibility. INTERLOX Phosphate S-600-ZMM: Micro-crystalline zinc phosphate coating for mixed metal lines, including steel, galvanized steel, and aluminum. Excellent quality; easy to control with little sludge formation. Subsequent paint provides humidity and detergent resistance, as well as good adhesion and flexibility. Zinc Phosphating--Auxiliary Products: INTERLOX Additive FG: Accelerator for depositing phosphate on steel. Results in closely packed phosphate crystal coating. In solution, it controls coating weight, grain struture and uniformity of coating. INTERLOX Adjuster F: Iron additive for zinc phosphate solutions. Allows instant iron seeding of new phosphate solutions, or solutions used on zinc-coated parts.


MCGEAN-ROHCO, INC.: INTERLOX Zinc Phosphate Systems(Continued): Zinc Phosphating--Auxiliary Products(Continued): INTERLOX Conditioner 1001 : A titanated compound for spray zinc phosphate systems. Added to rinse prior to phosphate stage. Helps promote tighter crystal structure on both cold-rolled and galvanized zinc-coated steel. INTERLOX Additive PA-215: Used with spray zinc phosphate system to promote acceleration of phosphate coating on a number of substrates. INTERLOX Compound 900-FA: Liquid black pre-dip for zinc phosphating where short immersion time is necessary. Ideal for automotive fasteners and hood hinges. (30 sec.-1 min.) Room temperature. INTERLOX Compound 902: Liquid black pre-dip for zinc phosphate where longer times are available. (2-5 min.) Ideal for auto fasteners and hood hinges. Meets Chrysler PS-80 for nuts and bolts and PS-4764 for steel stampings. Room temperature. Manganese Phosphating--Immersion: INTERLOX Phosphate MP: Crystalline manganese-iron phosphate for coating steel and iron substrates. Coating absorbs lubricating oils for fast break-in of moving parts (i.e. gears, pistons, cylinders, and other machine parts). Prevents scuffing, galling, and seizing of metal components. Good corrosion protection. Coating weight: 3,000-4,000 mg/sq.ft.

McGean-Rohco, lnc.

MCGEAN-ROHCO, INC.:

293

NORTHWEST Cleaners:

Spray Cleaners: INTERLOX Cleaner ST: For a variety of soils and base metals. Contains titanium to improve coverage and promote fine crystal growth. Especially effective on zinc-coated substrates. INTERLOX Cleaner 754-T: Cleans steel prior to zinc phosphating. Contains titanium. Improves coverage and promotes fine crystals. Low foaming. (70-140F.) For use on light soils, it's economical to use. JET Cleaner 91: Low temperature cleaner, easily dissolved in water, designed for cleaning steel and aluminum when both metals are processed in the same phosphate line. (Room temp. -140F.) JET Cleaner 751-NP: Designed to clean steel prior to iron and zinc phosphating. (70-170F. ) JET CLeaner 3-AT: All-temperature cleaner removes oil from galvanize, brass, copper and aluminum. Low foaming and defoaming against soluble oil and drawing compounds. Contains no phosphate, chromate or nitrate. (80-160F.) Metal Cleaner 414L: For both spray and immersion, this heavily fortified liquid cleaner is designed for heavily soiled steel and galvanized substrates. Low foaming, wide temperature range usage. Immersion Cleaners: TRT S-189: A heavy duty, alkaline soak cleaner for steel parts with a variety of soils such as oils, buffing compounds, polishing compounds and drawing compounds. TRT S-189 is readily treatable for water disposal and has a broad temperature range. (80-200F.) ROPREPP Cleaner R Special: A powdered, alkaline material used to remove heavy rust deposits, light scale films, and invisible oxide coatings prior to phosphating. Eliminates hydrogen embrittlement, the attack on base metal, and the need for special tanks. Other applications include buffing compound and carbonized soil removal, scale removal from phosphate washers with minimal attack to equipment. ALKALOX Cleaner 89: A heavy duty, alkaline soak cleaner to remove a variety of soils, oils, and buffing compounds from steel. Low/high temperature capabilities to meet varying soil conditions (80-200F.) ACTISALT Acid Powder 9: White, granular acid salt for effective removal of rust and metallic oxides. Doesn't interfere with phosphating. Spray or immersion use.

294


MCGEAN-ROHCO, INC.:

Paint Strippers:

Paint Stripper 1 587 : An alkaline liquid, highly fortified with efficient penetrating and bond-releasing agents. Used for stripping natural and synthetic organic finishes from steel, copper and brass. No phenolic ingredients; no objectionable odor or fumes. Rinses easily and completely. Excellent hard water tolerance; long tank life; economical. Paint Stripper 11 : A free-flowing, highly alkaline, hot paint stripper for steel only. Will remove organic films rapidly with good paint pigment dispersion and digestive action. Contains no phenolic compounds and rinses easily, even in hard water. Paint Stripper 1 5 4 0 : A non-phenolic liquid product composed of solvents and activators. Fortified with detergents and emulsifiers. Contains a combination of corrosion inhibitors and built-in seal to minimize evaporation losses. Can be used on all metals and alloys except magnesium--at room temperature. High speed penetration. Rinses easily; leaves no residue. Long solution life. Non-flammable.

Metalbrite Products Gorp.

METALBRITE PRODUCTS CORP.:

-

295

METALBRITE Rust Remover and Inhibitor:

Removes surface grease and oil Removes rust and corrosion Contains an inhibitor that prevents attack of the base metal by the cleaning solution. Removes residual grease or oil from the surface of the base metal leaving it squeaky clean for a new protective coating.

METALBRITE Rust and Corrosion Remover with Degreasers: METALBRITE rust and corrosion remover (MBRCR) is a specially formulated cleaning agent for the removal of rust with virtually no attack on the base iron surface. MBRCR can be painted onto any rusted metal surface by use of a roller, sprayer, brush, etc. In addition, MBRCR contains grease removers that eliminate the need for de-greasing or oil removal prior to application. No rubbing, scouring, or scraping is required. METALBRITE Bluing and Rust Remover: METALBRITE bluing and rust remover (MBBRR) removes bluing, rust, grease, and corrosion from firearms in one easy-to-use operation. MBBRR gets down to the base metal in minutes without harm to the metal, yet allows for deep penetration of corrosion. METALBRITE Copper and Brass Cleaner: METALBRITE copper and brass cleaner (MBCBC) is a specially formulated cleaning agent for the removal of corrosion and tarnish from copper and brass with virtually no attack on the base metal surface. MBCBC can be applied by use of a roller, sprayer, brush, sponge, paper towel, etc. and gently rubbed over the surface. If practical, the object can be immersed. Most important, no scouring or scraping is required. In addition, MBCBC contains grease removers that eliminate the need for degreasing or oil removal prior to application. After use, the object is washed with water and dried. Inhibitors in the formulation protect the metal surface, thus keeping its luster long lasting. METALBRITE SCALE REMOVER: METALBRITE scale remover (MBSR) is a specially formulated cleaner for the removal of scale and lime from iron and lead boiler tubes.


MORAWK FINISHING PRODUCTS, INC.: Factory Edger: 280-(Color Number): Available in 1 5 Wood Tone Colors:

MOHAWK Factory Edgers are made from light fast, heat stable colorants. Factory Edgers are used to replace color to worn edges, white edges, defects and other areas needing color. Advantages: 1 . Economical - long life 2. No mess - easy to use 3. Color computer controlled 4 . Uniform color strength 5. Quick solvent release 6. May be top coated 7. Safe to use on furniture laminates Factory Edger Colors: Black Cherry Oak , Dark Oak, Lt. Golden Oak, Weathered Pine Walnut, Light Walnut, Medium Brown

Brown, Van Dyke Nutmeg Oak, Extra Dark Oak, Medium Pecan Walnut, Extra Dark Walnut, Medium

Characteristics: Dry Time @ 72F Relative humidity 35% Dry to touch: 5 minutes Tack free: 7-8 minutes Dry to handle: 1 5 minutes Recoat interval: 15 minutes Flash Point: 50F Tag Closed Cup Weight per Gallon: 7.23 lbs/gal Specific Gravity: .a67 Air Quality Data: Contains photochemically reactive solvent Volatile Organic Compounds (VOC): 7.20 lbs/gal 866 grams per liter Package Life: 3 years Print Resistance: Factory Edgers dry quickly and hard. Total print resistance is obtained after one hour of drying. Specifications: Surface Preparation: Area where Factory Edger is used should be clean and dry. Application: Application of color should be in light, long strokes in preference to short choppy ones. Compatibility: Factory Edgers can be applied over many types of finishes such as lacquer, shellac, varnish, synthetic as well as padding agents.

Benjamin Moore & Co.

BENJAMIN MOORE

&

297

CO.: Alkyd Enamel Underbody 247:

A ready-mixed, full-bodied, easy-working, high build underbody designed for the professional painter.

Use : For interior use as an undercoater for new or previously painted wood, cured plaster and masonry surfaces. May be used on metal surfaces not subject to a rusting environment. May be used as an undercoater for both alkyd and latex coatings. Finish: Low Lustre Colors Available: White only, which may be tinted with up to 4 pint universal tinting colors per gallon. Package Size: Gallon and Five Gallon containers. Coverage: 500-600 sq. ft. (46.4-55.7 sq. meters) per gallon over smooth surfaces. Dry Time: To Touch--4 hours; To Handle--6 hours; To Recoat-Overnight. Mil Film Thickness: Wet--2.8 mils Dry--1.4 mils

@ @

550 sq. ft. per gallon. 550 sq. ft. per gallon.

Solids Content: By Weight--73%. By Volume--49%. Weight per Gallon: 12.1 Viscosity: 1 0 0

2

lbs.

5KU

Flash Point: Combustible Thinning/Cleanup: Thinning not normally required; if necessary for spray work or to ease brush or roller application, a small amount of mineral spirits or odorless thinner may be added. Clean up with mineral spirits. Performance Characteristics: - Produces a smooth, even finish. - Provides an ideal foundation for enamel finishes--alkyd or latex. - Brushes easily. - Outstanding holdout, leveling and sanding properties. - Dries to a hard, tightly bonded finish which may be sanded without gumming and will not crack or chip. Federal Specifications Generic Equivalent: TT-E-543A and TT-E-545B Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


BENJAMIN MOORE & SONS: Alkyd Primer Sealer 246:

An alkyd resin, pigmented primer designed for the professional painter. Use : For interior use for priming and sealing unpainted cured plaster and masonry surfaces; unpainted wood, previously painted surfaces requiring a primer sealer; and metal surfaces not subject to a rusting environment. Not recommended for direct use over unpainted wallboard surfaces. Finish: Low Lustre Colors Available: White only, which may be tinted with up to 3 pint universal tinting colors per gallon. Package Sizes: Gallon and Five Gallon containers Coverage: 400-600 sq. ft. (37.1-55.7 sq. meters) per gallon over smooth surfaces. 500 sq. ft. (46.4 sq. meters) per gallon--For use as a vapor barrier. Dry Time: To Touch--2-3 hours; To Handle--2-3 hours; To Recoat--overnight; To Service--overnight. Mil Film Thickness: Wet--3.2 mils @ 500 sq. ft. per gallon. Dry--1.3 mils @ 500 sq. ft. per gallon. Solids Content: By Weight--66%. By Volume--40%. Weight Per Gallon: 11.0 lbs. per gallon Viscosity: 90

k

5KU

Flash Point: Combustible Thinning/Cleanup: Thinning not normally required; if necessary, a small amount of mineral spirits may be added. Clean equipment with mineral spirits. Performance Characteristics: - Completely seals porous surfaces, insuring uniform appearance and holdout of finish coating. - Exhibits good hiding, excellent leveling qualities. - No objectionable odor during application. - Dries to a moderate lustre that enables the applicator to determine when surface is thoroughly sealed. - Possesses a "perm" rating of less than 1, when applied at a uniform rate of 500 sq. ft. per gallon, thereby effectively performing as a vapor barrier for outside walls and ceilings under unheated attics. It efficiently seals in moisture that would otherwise pass through these surfaces. Federal Specifications Generic Equivalent: TT-P-650CI TT-5-179B


BENJAMIN MOORE

& CO.:

299

Block Filler 145:

A high quality, full bodied vinyl-acrylic latex coating for filling small voids and cracks in rough masonry, concrete and cinder block designed especially for the professional painter.

Use : On unpainted exterior or interior poured concrete, cement or cinder block walls. Finish: Flat Colors Available: White. May be tinted with up to 2.0 fl. oz. of universal tinting colors per gallon. Package Sizes: Gallon and Five Gallon containers. Coverage: 75-150 sq. ft. (6.9-13.9 sq. meters) per gallon, according to surface texture. Dry Time: To Touch--1 hour; To Recoat--2 to 3 hours. Mil Film Thickness: Wet--21.4 mils @ 75 sq. ft.; 10.7 mils @ 150 sq. ft. per gallon. Dry--8.6 mils @ 75 sq. ft.; 4.3 mils @ 150 sq. ft. Solids Content: By Weight--61%. By Volume--40%. Weight per Gallon: 12.6 lbs. Viscosity: 127

f

3KU

Flash Point: None Thinning/Cleanup: Should be used as supplied; however, if it thickens due to evaporation, consistency can be adjusted by adding a small amount of water. Performance Characteristics: - Designed to provide a uniform surface on which to apply exterior or interior finishing paints--latex, alkyd or epoxy. - Features good hiding and enamel holdout. - Its vinyl-acrylic vehicle gives excellent durability and adhesion in exterior use. - It is not intended as a water-proof sealer or a finish coat but it will help to restrain penetration of water. - Should not be applied to surfaces freshly treated with silicone-type water repellents. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


BENJAMIN MOORE

&

CO.: Damp Surface Primer 205:

A low odor, alkyd enamel undercoater. Use: For interior use on wood, wallboard and properly cured plaster in dairies, food processing plants, shower rooms, textile plants and other constantly damp areas. Prepares surface for topcoating with IRONCLAD Damp Surface High Gloss Enamel (225). Not recommended for floors. Finish: Flat Colors Available: White. Can be tinted with up to 2.0 fl. 02. of universal tinting colors per gallon. Package Sizes: Gallons. Five Gallon containers available on special order. Coverage: 350-450 sq. ft. (32.5-41.8 sq. meters) per gallon Dry Time: To Touch--2 hour; To Handle--4 hours; To Recoat or Sand--overnight. Mil Film Thickness: Wet--4.O mils Dry--2.0 mils

@ @


Solids Content: By Weight--73%. By Volume--49%. Weight Per Gallon: 12 lbs. 3 oz. Viscosity: 1 1 0

f

5KU

Flash Point: Combustible Thinning/Cleanup: Thinning not normally required; when necessary, use small amounts of mineral spirits or odorless mineral spirits. Clean equipment with mineral spirits. Performance Characteristics: - Prepares surfaces for topcoating with IRONCLAD Damp Surface High Gloss Enamel (225). - Provides a moisture resistant system. - Smooth-flowing. - Heavy-bodied. - Can be sanded easily without gumming of the paper. - Very low odor. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

Benjamin Moore &

CO. 301

BENJAMIN MOORE 8 CO.: Epoxy Rust Inhibitive Primer 181: Epoxy Hardener (Curing Agent) 177/Epoxy Thinner 178: A polyamide epoxy, two-component primer formulated with a rust-inhibitive pigment. Use : On interior and exterior steel, aluminum or galvanized iron surfaces prior to topcoating with IRONCLAD Chemical & Water Resistant Epoxy Enamel(182) Finish: Semi-Gloss Colors Available: Red and White Package Sizes: Gallons Coverage: 200-225 sq. ft. per gallon (18.5-20.9

sq. meters).

Dry Time: To Touch--2 hours; To Handle--overnight; To Recoat-overnight. Pot Life: 18 hours

@

70F (21C)

Mil Film Thickness: Wet--7.6 mils @ 212 sq. ft. per gallon after mixing with IRONCLAD Epoxy Hardener (177). Dry--3.8 mils @ 212 sq. ft. per gallon after mixing with IRONCLAD Epoxy Hardener ( 1 77) Solids Content: By Weight--63%. By Volume--50%. Weight per Gallon: 12 lbs. 9 oz. Viscosity: 100

f

5 KU

Thinning/Cleanup: Thinning not normally required; if necessary use small amounts of IRONCLAD Epoxy Thinner (178). Clean equipment with IRONCLAD Epoxy Thinner (178). Performance Characteristics: - Ideally suited for industrial maintenance painting. - Resistant to most solvents and chemicals. - Possesses excellent adhesion qualities. - Outstanding leveling and hiding qualities. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

302


BENJAMIN MOORE & CO.: Epoxy Rust Inhibitive Primer 181 (Continued): Epoxy Hardener (Curing Agent) 177/Epoxy Thinner 178: IRONCLAD Epoxy Hardener (Curing Agent)-177: A chemical curing agent for use with IRONCLAD Epoxy Rust Inhibitive Primer (181) and IRONCLAD Chemical & Water Resistant Epoxy Enamel (182). IRONCLAD Epoxy Hardener (177) is to be mixed with equal volumes of the appropriate IRONCLAD product following the directions on the label. Available in gallon size only. IRONCLAD Epoxy Thinner--178: A solvent blend specifically intended for use with IRONCLAD industrial maintenance products. IRONCLAD Epoxy Thinner (178) possesses the high solvency needed to reduce consistencies sufficiently for conventional spray equipment without seriously lowering total solids or impairing film thickness. IRONCLAD Epoxy Thinner (178) is also useful as a cleanup solvent for painting tools and spray equipment or as a prepainting solvent for oily or greasy surfaces. It is available in quarts and gallons. Not compatible with water-thinned paints

Benjamin Moore & GO. 303

BENJAMIN MOORE &

CO.:

Exterior Primer 140:

A long oil, alkyd base pigmented primer designed for the professional painter. Use : For exterior priming of unpainted or previously coated wood, previously painted metal and cured or previously painted masonry surfaces, prior to the application of solvent or water-thinned house paints. Finish: Low Lustre Colors Available: White only, which can be tinted with up to 3 pint universal tinting colors per gallon. Package Sizes: Gallon and Five Gallon containers. Coverage: 450-550 sq. ft. (41.8-51.0 sq. meters) per gallon over smooth surfaces. Dry Time: To Touch--6 hours; To Handle--6 hours; To Recoat-24 hours. Mil Film Thickness: Wet--3.1 mils @ 500 sq. ft. per gallon. Dry--2.1 mils @ 500 sq. ft. per gallon. Solids Content: By Weight--83%. By Volume--68%. Weight Per Gallon: 12.8 lbs. Viscosity: 84

f

2KU

Flash Point: Combustible Thinning/Cleanup: Thinning not normally required; if necessary, a small amount of mineral spirits can be added. Do not add other paints or varnishes. Clean equipment with mineral spirits. Performance Characteristics: - Excellent holdout and hiding properties. - Seals uniformly. - Formulated to seal porous surfaces and improve bond over prepared chalky surfaces. - Exhibits excellent adhesion characteristics. - Provides a non-gloss film over which the finish coat performs to best advantage. Federal Specifications Generic Equivalent: TT-P-25E


BENJAMIN MOORE A

& CO.:

Galvanized Metal Latex Primer 155:

vinyl-acrylic latex primer.

Use: For interior or exterior use on new or unpainted galvanized metal gutters, leaders, siding, guardrails, roofs, vents and ducts that are free of rust. Finish: Low-Lustre Colors Available: White. Can Be tinted to light pastels with up to 2.0 fl. 02. of universal tinting colors per gallon. Package Sizes: Quarts and Gallons. Five Gallon containers available on special order. Coverage: 500-600 sq. ft. (46.4-55.7 sq. meters) per gallon. Dry Time: To Touch--1 hour; To Handle--2 hours; To Recoat--4 hours; High humidity may prolong drying time. Mil Film Thickness: Wet--2.9 mils @ 550 sq. ft. per gallon. Dry--1.2 mils @ 550 sq. ft. per gallon. Solids Content: By Weight--58%. By Volume--40%. Weight Per Gallon: 11 lbs. 14 Viscosity: 88

?

02.

3 KU

Flash Point: None Thinning/Cleanup: Thinning not normally required; when necessary use small amounts of clean water. Wash equipment in soapy water before, after and occasionally during use. Spray equipment should be given a final rinse with solvent. Performance Characteristics: - Excellent adhesion qualities. - Permits immediate painting of galvanized metal without weathering or special etching. - Suitable for use as a primer or as a finishing paint. - Equally compatible with other latex, alkyd or epoxy topcoats. - Quick-drying for same-day application of finish coat. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


305

BENJAMIN MOORE & CO.: MOORE'S Alkyd Masonry Sealer 077: A penetrating liquid surface c,onditioner. Use: For exterior use on weathered masonry surfaces or previously painted and chalky masonry. Finish: Flat Colors Available: White-(077) 01 and Clear (077) 00. White may be tinted with up to 3 pint of universal tinting colors per gallon of sealer. Package Sizes: Gallons; Five gallon containers available on special order. Coverage: Approximately 100-300 sq.ft. (9.2-27.8 sq. meters) per gallon. Dry Time: To Touch--2 hours; To Handle--4 hours; To Recoat-24 hours; To Service--Overnight. Mil Film Thickness: Wet--6-8 mils Dry--Minimal.

@

200 sq.ft. per gallon.

Solids Content: By Weight--41.3%. By Volume--21.3%. Weight Per Gallon: White--8.9 lbs.; Clear--7.2 lbs. Viscosity: 62

k

2 KU

Thinning/Cleanup: Thinning not normally necessary; if necessary, use up to 3 pint mineral spirits per gallon. Clean up equipment with mineral spirits. Performance Characteristics: - Reduces the porosity of masonry surfaces prior to top coating - Although designed primarily for a latex paint topcoat, any paint may be used. In the case of gloss paints, two coats may be necessary to achieve full gloss. - Do not use on new or fresh masonry. Alkali present in new concrete will inhibit the ability of MOORE'S Alkyd Masonry Sealer to provide adequate adhesion. - Does not eliminate the need for adequate surface preparation

.

Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

306


BENJAMIN MOORE & CO.:

MOORE'S Alkyd Primer Sealer 200:

A pigmented, alkyd base primer sealer under flat paints and enamels--alkyd or latex.

Use : Especially suited for priming unpainted cured plaster and masonry; unpainted wood, and surfaces previously finished with flat paint. It may also be used on metal surfaces where rusting conditions do not exist. Finish: Moderate Lustre Colors Available: White only; can be tinted with up to universal tinting colors per gallon.

& pint

Package Sizes: Quart, Gallon and Five Gallon containers. Coverage: 400-600 sq. ft. (37.1-55.7 sq. meters) per gallon; 500 sq. ft. (46.4 sq. meters) per gallon when used as a vapor barrier. Dry Time: To Touch--2-3 hours; To Handle--2-3 hours; To Recoat-overnight; To Service--overnight. Mil Film Thickness: Wet--3.2 mils Dry--1.3 mils

@ 500 @ 500

sq. ft. per gallon. sq. ft. per gallon.

Solids Content: By Weight--64%. By Volurne--40%. Weight Per Gallon: 10.6 lbs. Viscosity: 9 0

?

5 KU

Flash Point: Combustible Thinning/Cleanup: Thinning not normally required; if necesary, a small amount of mineral spirits or odorless paint thinner may be added. Clean equipment with mineral spirits. Performance Charactaristics: - Completely seals porous surfaces, assuring uniform appearance and holdout of the finish coat. - Has "perm" rating of less than 1 , qualifying as an effective vapor barrier. - Dries to moderate lustre that enables the applicator to determine when surface is thoroughly sealed. - Exhibits good hiding and excellent leveling qualities. - No unpleasant odor during application. Federal Specifications Generic Equivalent: TT-P-659C, TT-S-179B Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


307

BENJAMIN MOORE & CO.: MOORE'S Interior Wood Finishes Quick Dry Sanding Sealer 413:

A fast drying, vinyl-toluene modified alkyd resin clear wood sealer. Use: For interior use on doors, cabinets, paneling, trim or floors. ( A s a sealer only on floors.) Finish: Satin sheen when used as a complete finishing system. Colors Available: Clear Package Sizes: 4 Pint, Pint, Quart, Gallon. Five Gallon containers available on special order. Coverage: Approximately 400-450 sq.ft. (37.1-41.8 sq. meters) per gallon. Dry Time: To Touch--1 hour; To Handle--Dries for sanding in 2 or 3 hours; To Recoat--3 hours; To Service--overnight. Mil Film Thickness: Wet--3.8 mils Dry--Minimal

@ 425

sq. ft. per gallon.

Solids Content: By Weight--40%. By Volume--33%. Weight Per Gallon: 7.0 lbs. Viscosity: ( 5 0 KU Flash Point: Flammable Thinning/Cleanup: Thinning not normally required, if necessary add small amount of mineral spirits. Clean brushes and equipment with mineral spirits. Performance Characteristics: - Features fast dry, easy sanding without gumming, exceptional sealing and holdout. - Does double duty on all types of unfinished or stained interior wood surfaces: 1. Can be used as a sanding sealer under enamels or varnishes (except for urethane-based products). 2. Is especially suited as a filler, wash-coat sealer, or full sealer on new or resanded floors to be finished with any of MOORE'S Interior Clear Finishes (except urethane based products). - Can be used as an independent and complete finishing system for doors, cabinets and paneling. - Not for use as a finish coat on floors. Federal Specifications Generic Equivalent: TT-S-176E


BENJAMIN MOORE & CO.: Moore's Latex Exterior Primer 102: An alkyd modified acrylic latex primer, intended for use under latex house paints. Use : As an exterior primer primarily intended for use on both unpainted and previously painted siding, shingles and trim. It may also be used as a primer on all types of masonry construction and new or previously painted galvanized metal free from rust, that will be finished with a Latex House Paint. Finish: Flat Colors Available: White, which can be tinted with up to f pint universal tinting colors per gallon. Package Sizes: Quart and Gallon. Five Gallon containers available on special order. Coverage: 450-500 sq. ft. (41.8-46.4 smooth surfaces.

sq. meters) per gallon over

Dry Time: To Touch--1 hour; To Handle--2 hours; To Recoat--When spot-priming or double-coating; or applying finsh coat allow at least a three hour dry between coats. For most effective stain sealing action, allow to dry 24 hours before finishing with Latex House Paint. Mil Film Thickness: Wet--3.4 mils Dry--1.4 mils

@

@


Solids Content: By Weight--51%. By Volume--41%. Weight Per Gallon: 10.1 lbs. per gallon. Viscosity: 81

f

2KU

Flash Point: None Thinning/Cleanup: Thinning not normally required; if necessary, for spray work or to ease brushing or roller application, a small amount of clean water may be added. Clean with warm, soapy water. Performance Characteristics: - Provides a total latex system, offering excellent resistance to blistering on new construction, and minimizes staining tendencies of new cedar sidinglshingles or redwood siding. Easy to apply. - Excellent hiding and leveling properties. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

-


BENJAMIN MOORE & CO.:

309

MOORE'S Latex Quick Dry Prime Seal 201:

A rapid drying, vinyl-acrylic pigmented wall primer-sealer.

Use : Interior use for priming and sealing new or previously painted drywall construction, composition board, concrete, plaster and other porous surfaces. Finish: Flat

Colors Available: White only; can be tinted with up to universal tinting colors per gallon.

pint

Package Size: Quart, Gallon and Five Gallon containers Coverage: 500-600 sq. ft. (46.4-55.7 sq. meters) per gallon, depending on surface texture or porosity. Dry Time: To Touch--A hour; To Handle--1 hour; To Recoat--1 hour; To Service--4 hours. Mil Film Thickness: Wet--2.9 mils @ 550 sq. ft. per gallon. Dry--0.9 mils @ 550 sq. ft. per gallon. Solids Content: By Weight--47%. By Volume--30%. Weight Per Gallon: 11.1 Viscosity: 85

lbs.

3 KU

Flash Point: None Thinning/Cleanup: Thinning not normally required; if necessary, a small amount of clean water can be added. Do not overthin. Clean up with warm, soapy water; spray equipment should be given a final rinse with mineral spirits to prevent rusting. Performance Characteristics: - Ideal first coater for drywall construction, and other surfaces difficult to seal with solvent-thinned primers. - Resistant to mild alkali. - May be used over plaster or masonry surfaces which may not be completely dry. - Exhibits excellent holdout, hides well and offers smooth and effortless application. - Dries quickly. Federal Specifications Generic Equivalent: TT-P-650C Environmental Considerations: Formulated without lead or mercury.

310


BENJAMIN MOORE

&

CO.:

MOORE'S QD 30 ( 2 0 2 ) Aerosol Spray 491:

A general purpose solvent-thinned primer, sealer and stain suppressor.

Use: For interior use on bare or previously painted wood, plaster, drywall, plywood and hardboard surfaces. It may be used on exterior surfaces for limited purposes such as sealing knots and sap streaks. Finish: Flat Colors Available: White. May be tinted to light colors with up to 2.0 fl. 02. universal tinting colors per gallon. Package Sizes: Quart and Gallon. Five Gallon containers available in some areas. A l s o available in aerosol spray cans. Coverage: 400-450 sq. ft. (37.1-41.8 sq. meters) per gallon. Dry Time: To Touch--30 minutes; To Handle--1 hour; To Recoat-1 hour; To Service--1 hour. Mil Film Thickness: Wet--3.8 mils Dry--1.8 mils

@ @


Solids Content: By Weight--71%. By Volume--47%. Weight Per Gallon: 11.6 lbs. Viscosity: 82

f

4KU

Flash Point: Flammable ThinningICleanup: If thinning is required, it may be reduced with up to 1 pint mineral spirits per gallon. If faster dry is desired substitute VM&P Naphtha. Clean tools and spray equipment with thinning agent immediately after use. Performance Characteristics: - Effectively primes and seals charred or smoke stained surfaces. - Holds back water-soluble stains and most "bleeding" stains such as lipstick, crayon and grease. - Seals porous surfaces such as old flat wall paints and patches on previously painted surfaces. - Can be used as a spot-primer on exterior wood surfaces such as sealing knots or sap streaks. - It does not raise grain of wood. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

Benjamin Moore & Go. 31 1

BENJAMIN MOORE & Co.: MOORE'S speedy Primer Sealer 340:

An easy-brushing, rapid drying primer and stain sealer formulated with alcohol-soluble resins. Use : For sealing interior porous surfaces such as cured plaster, wallboard, ceiling tile, wood or plywood, old flat paint and patches in previously painted surfaces. Effective in holding back water stains and most other bleeding stains. Use on ceilings, walls, doors, trim, paneling and furniture. Finish: Low Eggshell Colors Available: White. May be tinted with up to 2.0 fl. oz. universal tinting colors per gallon. Package Sizes: Quart and Gallon. Five Gallon containers available on special order. Also available in aerosol spray cans. Coverage: 400-500 sq. ft. (37.1-46.4 sq. meters) per gallon, depending on surface porosity and texture. Dry Time: To Touch--Dust free in a few minutes. To Handle-30 minutes. To Recoat--Under normal drying conditions; it is ready for sanding or recoating in 30-60 minutes. If a second coat of SPS is required to stop severe staining, allow first coat to dry at least 2 hours. Mil Film Thickness: Wet--3.6 mils @ 450 sq. ft. per gallon. Dry--1.3 mils @ 450 sq. ft. per gallon. Solids Content: By Weight--59%. By Volume--37%. Weight Per Gallon: 10.6 Viscosity: 60

f

lbs.

1KU

Flash Point: Flammable Thinning/Cleanup: Thinning not normally required; if necessary, for spray application or excessive evaporation, add a small amount of denatured alcohol. Cleanup with alcohol or household ammonia. Performance Characteristics: - Excellent for holding back water stains, stains from knots and other bleeding stains. - Ease of brushing and rapid dry. - Flows out well. - Hides adequately and assures uniform gloss and color of finishing coat. - Its low eggshell finish permits perfect topcoat adhesion, and can be sanded to provide an exceptionally smooth finish where desired. - It is not recommended for general use over wallpaper.


BENJAMIN MOORE 8 CO.:

MOORWHITE Primer 100:

A premium quality long-oil, alkyd-based fast drying pigmented pr imer

.

Use : A s an exterior priming coat for unpainted wood, cured masonry and previously painted weathered surfaces including aluminum siding. Can be used under latex or water-thinned paints, alkyd enamels and house paints. Suitable for a variety of exterior surfaces such as side-walls, trim and shutters.

Finish: Low Lustre Colors Available: White, Red

&

Gray

Package Sizes: Quart, Gallon and Five Gallon containers Coverage: 500-550 sq. ft. (46.4-51 .O sq. meters). Dry Time: To Touch-6 hours; To Handle-6 hours; To Recoat-Overnight; To Service-overnight. Mil Film Thickness: Wet-3.1 mils Dry-2.0 mils

@ @


Solids Contents: By Weight-83%. By Volume-66%. Weight Per Gallon: 12.8 lbs. Viscosity: 80

?

2KU

Flash Point: Combustible ThinningICleanup: Thinning not normally required; if necessary, a small amount of mineral spirits can be added. Do not add other paints, oils, driers or varnishes. Clean equipment with mineral spirits. Performance Characteristics: - Easy to apply by brush, roller or spray gun. - Excellent hiding and leveling properties. - Improves adhesion on weathered and prepared chalky surfaces. - Provides a uniformly sealed surface that prevents absorption of vehicle from finish coat. - Mildew Resistant - For best results, top coat should be applied within a reasonable length of time--preferably no more than one month after priming. Federal Specifications Generic Equivalent: TT-P-25E Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


313

BENJAMIN MOORE & CO.: Quick Dry Industrial Rust Inhibitive Primer 168: A fast-drying, phenolic-modified, alkyd, rust-inhibitive primer. Use: Specially folrmulated for use on new or previously painted interior or exterior metal surfaces. Finish: Eggshell Colors Available: White and Red. White can be tinted with up to 2.0 fl. oz. of universal tinting colors per gallon. Package Sizes: Quarts and Gallons. Five Gallon containers available on special order. Coverage: Apply at 500-600 sq. ft. (46.0-57.5 sq. meters) per gallon. Dry Time: To Touch--1 hour; To Handle--2 hours; To Recoat--3-4 hours. Mil Film Thickness: Wet--2.9 mils Dry--1.1 mils

@ @


Solids Content: By Weight--65%. By Volume--42%. Weight per Gallon: 1 0 lbs. 9 Viscosity: 8 3

f

02.

2KU

Plash Point: Combustible Thinning/Cleanup: Thinning not normally required; when necessary, use small amounts of mineral spirits. Clean equipment with mineral spirits. Performance Characteristics: - Permits application of a complete primerlfinish coat system within one working day. - Excellent corrosion resistance. - Excellent adhesion. - Excellent foundation metal primer when time is an important factor. - May be topcoated with latex or alkyd paints or enamels. - Excellent hiding qualities. - Excellent leveling properties. Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


BENJAMIN MOORE

& CO.:

RETARD-X Rust Inhibitive Latex Primer 1 6 2 :

Alkyd modified acrylic rust-preventative latex primer. Use: For new or previously painted interior or exterior metal surfaces such a s steel coiumns , trusses, tanks , substation steel and galvanized iron structures, as well as masonry. Finish: Flat Colors Available: White and Red. White can be tinted with up to 2.0 fl. 02. of universal tinting colors per gallon to make light pastels. Package Sizes: Pints, Quarts and Gallons. Five Gallon containers available on special order. Coverage: 375-425 sq. ft. (34.8-39.4 sq. meters) per gallon. Dry Time: To Touch--1 hour; To Handle--2 hours; To Recoat--4 hours

.

Mil Film Thickness: Wet--4.0 mils Dry--1.6 mils

@ @


Solids Content: By Weight--51%. By Volume--40%. Weight per Gallon: 10 lbs. 2 oz. Viscosity: 85

f

3KU

Flash Point: None Thinning/Cleanup: Thinning not normally required; if necessary, use small amounts of clean water. Clean up with warm, soapy water. Performance Characteristics: - Useful in controlling rust leaching of reinforcing steel in pre-stressed concrete ceilings. - Provides a firm foundation for topcoating with latex finishes, providing an all latex system. - Fast dry permits two coat work in one working day. - Alkali resistant. - No fire hazard during use or in storage. - Excellent adhesion and may be applied over damp masonry surfaces. - Easy to apply by brush, roller or spray. Fast cleanup with soapy water. - Very low in odor.

-

Environmental Considerations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.


BENJAMIN MOORE

&

CO.:

315

Sanding Sealer Clear 253:

A fast drying vinyl-toluene wood sealer designed for the professional painter.

Use : For interior use on unfinished wood surfaces such as doors, cabinets, paneling and floors prior application of varnish finish coat. Finish : When used as a finish system where two or three coats have been applied and buffed with steel wool, it exhibits a mellow lustre, hand rubbed finish. Colors Available: Clear. Package Sizes: Gallon and Five Gallon containers. Coverage: Approximately 6 0 0 sq. ft. (55.7 sq. meters) per gallon Dry Time: To Touch--1 hour; To Handle--2-3 hours; To Recoat--2-3 hours; To Service--2-3 hours Mil Film Thickness: Wet--2.7 mils @ 600 sq. ft. per gallon. Dry--0.8 mils @ 600 sq. ft. per gallon. Solids Content: By Weight--38%. By Volume--31%. Weight Per Gallon: 6.9 lbs. Viscosity: (50 KU Flash Point: Flammable Thinning/Cleanup: For spray application thin with 1 quart mineral spirits per gallon. When sealer is used as a wash coat or floor sealer, thin with up to equal parts mineral spirits. No thinning required for use as a full seal coat. Clean up with mineral spirits. Performance Characteristics: - Durable, crystal clear, wood sealer - Exceptional sealing and holdout - Sands easily without gumming. - Does double duty on all types of unfinished or stained interior wood surfaces: 1. Can be used as a sanding sealer under enamels or varnishes (except for urethane-based products). 2. It performs equally well as a filler for closegrained wood, a wash-coat, or as a full sealer on new or resanded wood. - Can be used as an independent and complete finishing system for standing surfaces such as doors, cabinets and paneling. - Not for use as a finish coat on floors. Federal Specifications Generic Equivalent: TT-S-176E


BENJAMIN MOORE & CO.: Vinyl Latex Primer Sealer 252: A vinyl-acrylic latex pigmented wall primer-sealer designed for the professional painter.

Use : For interior use on new or previously painted drywall construction, plaster, concrete or other porous interior surfaces. Finish: Flat Colors Available: White only, which may be tinted with up to & pint universal tinting colors per gallon. Package Size: Gallon and Five Gallon containers. Coverage: 500-600 sq. ft. (46.4-55.7 over smooth surfaces.

sq. meters) per gallon

Dry Time: To Touch--$ hour; To Handle--1 hour; To Recoat--1 hour; To Service--4 hours. Mil Film Thickness: Wet--3.0 mils Dry--0.7 mils

@ 550 @ 550

sq. ft. per gallon. sq. ft. per gallon.

Solids Content: By Neight--38%. By Volume--24%. Weight Per Gallon: 10.2 lbs. Viscosity: 92

*

3 KU

Flash Point: None ThinningICleanup: Thinning not normally required; if necessary, a small amount of clean water may be added. Do not overthin. Clean up with warm, soapy water; spray equipment should be given final rinse with mineral spirits to prevent rusting. Performance Characteristics: - Excellent holdout. - Sides well and offers smooth and effortless application. - It is especially good for priming wallboard since it will not raise the nap. - Not recommended for use on bare metal or unpainted wood. Federal Specifications Generic Equivalent: TT-P-650C Environmental Considerations: Formulated without lead or mercury.


BENJAMIN MOORE

& CO.:

317

WALL-GRIP 1, 2, 3 (203):

WALL-GRIP 1 (20301): A transparent acrylic latex sealer. WALL-GRIP 2 (20302): A pigmented vinyl acrylic latex sealer. WALL-GRIP 3 (20303): A transparent acrylic latex sealer. Use : WALL-GRIP 1: For application to previously painted or hard/ glossy-surfaces such as glass, formica, or ceramic tile; it also allows new wallcovering to adhere to previously hung vinyl. WALL-GRIP 2: For priming and sealing bare-wallboard. Facilitates stripping of wallcoverings without damage to substrate. Do not use under pre-pasted wall coverings. WALL-GRIP 3: For use under pre-pasted or heavy wallcoverings where adhesion is a problem.

Finish: Low Lustre Colors Available: WALL-GRIP 1 (light blue tint); WALL-GRIP 2 (White). WALL-GRIP 3 (light green tint). Viscosity: WALL-GRIP 1

&

3-80

?

2KU; WALL-GRIP 2-90 i 2KU

Performance Characteristics: - Excellent sealing qualities facilitate the positioning and pattern matching of wallcoverings, smoothing out wrinkles and airpockets. - Provides a base which allows pastes and adhesives to bond well, and helps prevent the opening of seams. - Indispensible value over unusually difficult surfaces such as recovering vinyl with vinyl. - Makes wallcovering application easier and less timeconsuming. - No unpleasant odor. - Spreads easily and dries quickly. - WALL-GRIP 1 will also prime bare plaster and wallboard for topcoating with both solvent and latex paints. - WALL-GRIP 2 may also be used to prime bare wallboard for topcoating with both solvent and latex paints. Can be tinted to pastel shades with up to 2.0 fl. oz. of universal tinting colors per gallon of sealer. For use under wall-coverings which do not fully mask the substrate. Environmental Coniderations: Formulated with non-photochemically reactive solvents. Formulated without lead or mercury.

318 Prepaint @ecialties and Surface Tolerant Coatings

BENJAMIN MOORE I CO.:

6 6 0 Solvent Thinner 293:

A special thinner recommended for use where a strong solvent is required. Use : Suitable for use in most solvent-thinned oil, alkyd, epoxy, urethane and other synthetic base products. Not recommended for water-thinned paints. IRONCLAD 660 Solvent Thinner is especially recommended for thinning coatings to be applied with spray equipment. Because of its high solvent strength, less thinner is needed to reach spraying consistency and maximum hiding can be retained. IRONCLAD 660 Solvent Thinner improves penetration and adhesion. It also evaporates quickly, minimizing sagging and running of sprayed coatings. It is very effective for cleaning brushes and other painting equipment. Can also be used to remove grease, dirt and grime from surfaces prior to painting. It is available in quarts and gallons. Weight Per Gallon: 6 lbs. 1 3 oz. Flash Point: Flammable

National Solvent Gorp.

NATIONAL SOLVENT CORP.:

Paint Remover

&

319

Wood Refinishers:

Non-Flammable Paint & Varnish Remover: Premium quality Remover for shellac, varnish, lacquer, paint, enamel, latex, and synthetic finishes, such as epoxy and polyurethane. NASCO Remover removes all finishes and multiple layers of finish quickly and efficiently, without harming the surface. Wipe off or water wash as desired. NASCO Paint Remover is nonflammable. Tung Oil Finish: Produces a hand-rubbed finish that will enhance the rich color, beauty and grain of the wood. Tung Oil is water and alcohol resistant. Its protective coating adds a beautiful satin-luster finish without build-up and it's easy to apply. Furniture Refinisher: The ideal product for removing varnish, shellac, lacquer or other clear finish as part of a refinishing project. Polyurethane: A long-lasting protective finish that resists water and alcohol, NASCO Polyurethanes are available in either gloss or matte finish. Use Polyurethane as the final step in Furniture Refinishing to enhance the beauty of the wood and give a hard protective coating. Clear Wood Protector: A superior quality clear varnish which has been specially formulated to meet the demand for a durable clear finish for the growing patio and deck market. Use Clear Wood Protector on picnic tables, outdoor furniture, doors, and other exterior wood surfaces where a clear finish that resists sunlight and water are required. Outperforms polyurethanes and other clear finishes for exterior use. Linseed Oil (Boiled): Keep wood surfaces looking like new by applying a coat of NASCO Linseed Oil to replace the natural oils lost from wood through changes in temperature and time. A light coat applied every month will keep wood in top condition and preserve your investment. Lemon Oil: Use Lemon Oil to clean, polish and preserve fine wood furniture. NASCO Lemon Oil brings out the natural beauty of wood without build-up. Contains no waxes or silicones.



Paint Thinners EL Solvents:

Mineral Spirits: A high purity petroleum based solvent specially refined to have a low odor and high solvency. Use NASCO Mineral Spirits for thinning oil based paints, varnishes, stains and enamels; for cleaning surfaces prior to painting; and for clean-up of tools and equipment after painting. Paint Thinner Code 66: A special blend of exempt mineral spirits to meet EPA emission requirements. NASCO Paint Thinner cleans and thins paint products just like the Mineral Spirits. In addition, it protects the environment. TURPEX: Premium quality blend of synthetic solvents designed to replace Turpentine. TURPEX has the high solvency of turpentine but at a lower cost. This solvent is the overwhelming choice of professional painters. Turpentine: The premium thinner for all oil based paints, varnishes and enamels. NASCO Turpentine is Pure Gum Turpentine and is the highest, purest grade available. Turpentine aids the penetratioi of all types of wood and enhances the bonding properties of all coatings. Turpentine has a fresh pine aroma. Turpentine is not a good choice as a cleaning solvent since it leaves a slight gum residue. Denatured Alcohol: A blend of alcohols which is designed for thinning shellac products and for clean-up of tools after applying shellac. Denatured Alcohol is useful as a cleaner for glass, metal, rubber and leather surfaces. Due to its high purity, NASCO Denatured Alcohol is the fuel of choice for chafing dishes, alcohol burners and stoves. Lacquer Thinner: A medium fast blend of solvents designed for thinning lacquers in brush, spray and dip applications. NASCO Lacquer Thinner is not designed for use with Acrylic or Automotive Lacquer Finishes. Lacquer Thinner is useful as a degreasing agent and as a general purpose cleaning solvent.

National Solvent Corp. 321


Paint Thinners

&

Solvents(Continued):

C.P. Acetone: A fast evaporating, strong solvent which is useful for cleaning unpainted fiberglass surfaces and for removing greases and waxes from glass, metal and leather surfaces. Acetone evaporates quickly leaving no residue. Use Acetone with care since it will soften and dissolve many plastics and synthetic fabrics. Linseed Oil (Boiled): Use as a thinner for oil based paints, caulking and glazing compounds. Adding Linseed Oil increases elasticity to resist weathering and cracking. Linseed Oil is useful as a cleaner and restorer for natural wood surfaces. Linseed Oil (Raw): Economical thinner for oil based products. Has the same properties as Boiled Linseed Oil, but dries slower. SANDPAPER-IN-A-CAN: A special blend of materials for cleaning, degreasing and removing the gloss from previously painted surfaces prior to repainting. SANDPAPER-IN-A-CAN eliminates the need for scuff sanding of glossy surfaces and aids the bonding of new paint. Brush Cleaner: A premium blend of solvents designed to quickly and easily clean pure bristle, nylon and polyester brushes. Softens hard coatings without damaging the brush. Not intended for cleaning synthetic bristles. Do not use Brush Cleaner to thin coatings. Latex Brush Cleaner: A specially ammoniated soap for cleaning latex paints from equipment. May also be used as for floors, woodwork and glass

concentrate specially formulated brushes, rollers and painting a general household cleaner surfaces.

MEK (Methyl Ethyl Ketone): An industrial quality solvent for use with lacquers and finishes. VM&P Naphtha: A fast drying solvent that replaces paint thinner. May be used with oil based paints, varnishes and enamels.

Toluene : An industrial quality solvent for use with synthetic finishes, varnishes and enamels. Xylene : An industrial quality solvent which is similar to Toluene, but is slower drying.


THE NAVAL JELLY

CO.:

NAVAL JELLY:

NAVAL JELLY removes rust Brush it on--Hose it off1 Brush it on. Let stand a few minutes or several hours depending upon the depth of the rust. Hose off with fresh water. Dissolves rust from iron or steel No more scraping! No more sandblasting! No more wirebrushing! NAVAL JELLY eliminates the time and drudgery of rust removal and does the job far more effectively than old, harsh mechanical Removes Rust Quickly. Clings to verticals and overheads. Composition: Ingredients Phosphoric Acid Sulfamic Acid Isopropyl Alcohol Silicon Dioxide Water Polysaccharide Additives Color, Odor Chemical and Physical Properties: Vapor Pressure Vapor Density Solubility in Water Appearance Specific Gravity Boiling Point PH Odor

CAS. #

%

7664-38-2 5329-1 4-6 67-63-0 7 6 3 1 -86-9 7732-1 8-5

25-30 (5 (5

Prepaint Specialties and Surface Tolerant Coatings

Coatings Materials and Surface Coatings

Surface Coatings

Paint and Surface Coatings: Theory and Practice

Surface Coatings for Protection Against Wear

Resins for Surface Coatings. Alkyds & Polyesters

Harrison's Hematology and Oncology (Harrison's Specialties)

Rock Coatings (Developments in Earth Surface Processes 6)

Diagnosis and fault-tolerant control

Rock Coatings (Developments in Earth Surface Processes 6)

Diagnosis and Fault-Tolerant Control

Ceramic Films and Coatings

Fault-Tolerant Systems

Coatings Tribology

Military Occupational Specialties: Change and Consolidation

BRS Surgical Specialties

Careers in Nursing Specialties

Fault-Tolerant Systems

Skew-Tolerant Circuit Design

Fault-tolerant IP and MPLS networks

Oxford Handbook of Clinical Specialties

The Tolerant Society

Fault-Tolerant Systems

Fault-Tolerant Systems

Coatings Of Polymers And Plastics

Protein-Based Films And Coatings

Coatings of Polymers and Plastics

Wood Coatings Theory and Practice

Wood Coatings: Theory and Practice

Fault Tolerant Flight Control And Guidance Systems

Prepaint Specialties and Surface Tolerant Coatings

Coatings Materials and Surface Coatings

Surface Coatings

Paint and Surface Coatings: Theory and Practice

Surface Coatings for Protection Against Wear

Resins for Surface Coatings. Alkyds & Polyesters

Harrison's Hematology and Oncology (Harrison's Specialties)

Rock Coatings (Developments in Earth Surface Processes 6)

Diagnosis and fault-tolerant control

Rock Coatings (Developments in Earth Surface Processes 6)

Diagnosis and Fault-Tolerant Control

Ceramic Films and Coatings

Fault-Tolerant Systems

Coatings Tribology

Military Occupational Specialties: Change and Consolidation

BRS Surgical Specialties

Careers in Nursing Specialties

Fault-Tolerant Systems

Skew-Tolerant Circuit Design

Fault-tolerant IP and MPLS networks

Oxford Handbook of Clinical Specialties

The Tolerant Society

Fault-Tolerant Systems

Fault-Tolerant Systems

Coatings Of Polymers And Plastics

Protein-Based Films And Coatings

Coatings of Polymers and Plastics

Wood Coatings Theory and Practice

Wood Coatings: Theory and Practice

Fault Tolerant Flight Control And Guidance Systems

Recommend Documents