New Avenues to Efficient Chemical Synthesis. Emerging Technologies

Ernst Schering Foundation Symposium Proceedings 2006-3 New Avenues to Efficient Chemical Synthesis Ernst Schering Fou...

Author: P.H. Seeberger | T. Blume

15 downloads 696 Views 8MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

Ernst Schering Foundation Symposium Proceedings 2006-3 New Avenues to Efficient Chemical Synthesis

Ernst Schering Foundation Symposium Proceedings 2006-3

New Avenues to Efficient Chemical Synthesis Emerging Technologies P.H. Seeberger, T. Blume Editors With 144 Figures

123

Series Editors: G. Stock and M. Lessl

Library of Congress Control Number: 2007928115 ISSN 0947-6075 ISBN 978-3-540-70848-3 Springer Berlin Heidelberg New York This work is subject to copyright. All rights are reserved, whether the whole or part of the material is concerned, specifically the rights of translation, reprinting, reuse of illustrations, recitation, broadcasting, reproduction on microfilms or in any other way, and storage in data banks. Duplication of this publication or parts thereof is permitted only under the provisions of the German Copyright Law of September 9, 1965, in its current version, and permission for use must always be obtained from Springer-Verlag. Violations are liable for prosecution under the German Copyright Law. Springer is a part of Springer Science+Business Media springer.com © Springer-Verlag Berlin Heidelberg 2007 The use of general descriptive names, registered names, trademarks, etc. in this publication does not emply, even in the absence of a specific statemant, that such names are exempt from the relevant protective laws and regulations and therefor free for general use. Product liability: The publisher cannot guarantee the accuracy any information about dosage and application contained in this book. In every induvidual case the user must check such information by consulting the relevant literature. Editor: Dr. Ute Heilmann, Heidelberg Desk Editor: Wilma McHugh, Heidelberg Production Editor: Martin Weißgerber, Leipzig Cover design: design & production, Heidelberg Typesetting and production: LE-TEX Jelonek, Schmidt & Vöckler GbR, Leipzig 21/3180/YL – 5 4 3 2 1 0 Printed on acid-free paper

Preface

Chemical synthesis is one of the key technologies in modern drug discovery and development. For the rapid preparation of new test compounds and drug development candidates with often highly complex chemical structures it is crucial to use state of the art chemical technologies. In recent years several innovative technologies with great potential for chemical synthesis have emerged: 1) Microreactor Chemistry as a New Tool in Discovery, Development and Production Synthesis in microreactors is currently a rapidly developing field of research. Compared to traditional batch process methods this flow-through technology holds many advantages including very good mixing and heat transfer capabilities that often result in improved reaction selectivities and yields. Furthermore, hazardous reactions can be controlled much better in microfluidic systems and reduce the danger to workers and the environment. Importantly, the need for larger amounts of drug substances can be satisfied rapidly by just numbering-up the microreactor systems. Thus, the problems that are often encountered with traditional scale-up of batch processes can be overcome. Still, challenges facing this technology such as handling of solids or materials precipitating during the reaction might lead to clogging of the reactors. Chemistry in microreactor systems is a field of active research in many leading competence

VI

Preface

centers around the world as well as in many industrial laboratories in pharmaceutical and fine chemical industries. 2) Nanotechnology and Catalysis Research in Synthesis Nanotechnology is an evolving research area especially in materials and biotechnological sciences. First studies have shown that the special properties of nanoparticles can give rise to highly active and selective catalysts to enable chemists to perform entirely novel transformations. Discussion and evaluation of the potential of nanoparticles for chemical research in a pharmaceutical company with experts in the field was needed. Other areas in catalysis like biotransformations and metal catalyst screening and development continue to expand the possibilities for the manufacturing of test compounds and development candidates. 3) Rapid Microwave Assisted Organic Synthesis Another synthesis technology which has just started to impact and change the way chemical synthesis is performed in many laboratories is microwave assisted organic synthesis. Using microwave reactors, reaction times often can be reduced from hours or days to minutes or even seconds. Selectivities and yields often can be increased drastically. Therefore, this technology has the potential to increase the output of chemical drug discovery units enormously. An important question in this field is how to scale up these transformations in microwave reactors up to kilogram scale. 4) New Developments in Solid Supported Synthesis Solid-supported technologies are already well established methods in medicinal chemistry and automated synthesis. Over the last couple of years new trends have evolved in this field which are of utmost importance as they have the potential to revolutionize the way chemical synthesis especially for library production is performed. Microchip-based synthesis technologies and multistep sequences with solid-supported catalysts or reagents in flow-through systems are only two spectacular examples. A new approach is the use of solid-supported systems for the scale-up of chemical reactions thereby enabling the rapid and smooth transition from discovery to development units.

Preface

VII

The importance of chemical synthesis as a core technology in the pharmaceutical and chemical industry, prompted us to organize an Ernst Schering Foundation Workshop in 2006 to bring together scientific leaders from both academia and industry to discuss the implication of new technologies for drug discovery and development. The lectures presented at the symposium are collected in this book. The editors hope that this volume will prove useful to chemists in the pharmaceutical industry as well in research institutions and universities interested in chemical synthesis for drug discovery and development. P.H. Seeberger T. Blume

Contents

Microreactors as Tools in the Hands of Synthetic Chemists P.H. Seeberger, K. Geyer, J.D.C. Codée . . . . . . . . . . . . . .

1

Micro-Fluidic and Lab-on-a-Chip Technology X. Zhang, S.J. Haswell . . . . . . . . . . . . . . . . . . . . . .

21

Microreactors as New Tools for Drug Discovery and Development S.Y.F. Wong-Hawkes, J.C. Matteo, B.H. Warrington, J.D. White .

39

Microchemical Systems for Discovery and Development K.F. Jensen . . . . . . . . . . . . . . . . . . . . . . . . . . . .

57

Isoindolones and Related N-Heterocycles via Palladium Nanoparticle-Catalyzed 3-Component Cascade Reactions R. Grigg, V. Sridharan . . . . . . . . . . . . . . . . . . . . . .

77

Applying Homogeneous Catalysis for the Synthesis of Pharmaceuticals M. Beller . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99

X

Contents

An Integrated Approach to Developing Chemoenzymatic Processes at the Industrial Scale J. Tao, L. Zhao . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Scale-Up in Microwave-Accelerated Organic Synthesis H. Lehmann . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Solid Supported Reagents in Multi-Step Flow Synthesis I.R. Baxendale, S.V. Ley . . . . . . . . . . . . . . . . . . . . . . 151 Solid-Phase Supported Synthesis: A Possibility for Rapid Scale-Up of Chemical Reactions M. Meisenbach, T. Allmendinger, C.-P. Mak . . . . . . . . . . . 187 Microstructured Reactors for Development and Production in Pharmaceutical and Fine Chemistry V. Hessel, P. Löb, U. Krtschil, H. Löwe . . . . . . . . . . . . . . 205

List of Editors and Contributors

Editors Seeberger, P.H. Laboratory for Organic Chemistry, Swiss Federal Institute of Technology (ETH) Zürich, HCI F 315, Wolfgang-Pauli-Str. 10, 8093 Zürich, Switzerland (e-mail: [email protected]) Blume, T. Process Research B / Automated Process Optimization, Global Chemical Development, Bayer Schering Pharma AG, Müllerstr. 178, 13342 Berlin, Germany (e-mail: [email protected])

Contributors Allmendinger, Th. Chemical and Analytical Development, Novartis Pharma AG, 4002 Basel, Switzerland Baxendale, I.R. Innovative Technology Center (ACS), Department of Chemistry, University of Cambridge, Cambridge, CB21EW, United Kingdom (e-mail: [email protected])

XII


Grigg, R. Chemistry Department, Leeds University, Leeds LS2 9JT, United Kingdom Beller, M. Leibniz-Institut für Katalyse e.V. University of Rostock, Albert-Einstein-Straße 29a, 18059 Rostock, Germany (e-mail: [email protected]) Codée, J.D.C. Laboratory for Organic Chemistry, Swiss Federal Institute of Technology (ETH) Zürich, HCI F 315, Wolfgang-Pauli-Str. 10, 8093 Zürich, Switzerland Geyer, K. Laboratory for Organic Chemistry, Swiss Federal Institute of Technology (ETH) Zürich, HCI F 315, Wolfgang-Pauli-Str. 10, 8093 Zürich, Switzerland Haswell, St. J. Department of Chemistry, The University of Hull, Hull, HU6 7RX, United Kingdom (e-mail: [email protected]) Jensen, K. Department of Chemical Engineering, Masschusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139, USA (e-mail: [email protected]) Lehmann, H. Novartis Instiute for Biomedical Research, Discovery Technologies/Preparation Laboratories, Klybeckstrasse 191, 4002 Basel, Switzerland (e-mail: [email protected])


Ley, S.V. Innovative Technology Center (ACS), Department of Chemistry, University of Cambridge, Cambridge, CB21EW, United Kingdom (e-mail: [email protected]) Mak, Ch.-P. Chemical and Analytical Development, Novartis Pharma AG, 4002 Basel, Switzerland Matteo, J.C. 217 FenceRail Gap, Walland, Tennessee, TN 37886, USA Meisenbach, M. Chemical and Analytical Development, Novartis Pharma AG, 4002 Basel, Switzerland (e-mail: [email protected]) Sridharan, V. Chemistry Department, Leeds University, Leeds LS2 9JT, United Kingdom Tao, J. BioVerdant, Inc., 7330 Carroll Road, San Diego, CA 92121, USA (e-mail: [email protected]) Warrington, B.H. 45, The Drive, Hertford, SG14 3DE, United Kingdom (e-mail: [email protected]) White, J.D. William James House, Cowley Road, Cambridge CB4 0WX, United Kingdom Wong-Hawkes, S.Y.F. 4 Hull Close, Cheshunt, EN7 6XG, United Kingdom

XIII

XIV


Zhang, X. Department of Chemistry, The University of Hull, Hull, HU6 7RX, United Kingdom Zhao, L. BioVerdant, Inc., 7330 Carroll Road, San Diego, CA 92121, USA

Ernst Schering Foundation Symposium Proceedings, Vol. 3, pp. 1–19 DOI 10.1007/2789_2007_025 © Springer-Verlag Berlin Heidelberg Published Online: 23 May 2007

Microreactors as Tools in the Hands of Synthetic Chemists P.H. Seeberger(u) , K. Geyer, J.D.C. Codée Laboratory for Organic Chemistry, Swiss Federal Institute of Technology (ETH) Zurich, HCI F 315, Wolfgang-Pauli-Str. 10, 8093 Zurich, Switzerland email: [email protected]

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 2 Microfluidic Reactor Types . . . . . . . . . . . . . . . 3 Flow Types and Introduction of Solvents and Reagents 4 Synthesis in Microchemical Systems . . . . . . . . . . 5 Liquid Phase Reactions . . . . . . . . . . . . . . . . . 6 Liquid–Solid Phase Reactions . . . . . . . . . . . . . . 7 Liquid–Gas Reactions . . . . . . . . . . . . . . . . . . 8 Liquid–Gas–Solid Reactions . . . . . . . . . . . . . . 9 Synthesis of Imaging Agents . . . . . . . . . . . . . . 10 Microreactor Synthesis of β-Peptides . . . . . . . . . . 11 Conclusion and Outlook . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

. . . . . . . . . . . .

2 3 5 6 6 7 8 9 10 11 13 14

Abstract. Recent developments in the construction of microstructured reaction devices and their wide-ranging applications in many different areas of chemistry suggest that microreactors may significantly impact the way chemists conduct experiments. Miniaturizing reactions offers many advantages for the synthetic organic chemist: high-throughput scanning of reaction conditions, precise control of reaction variables, the use of small quantities of reagents, increased safety parameters, and ready scale-up of synthetic procedures. A wide range of single and multiphase reactions has been performed in microfluidic-based devices. Certainly, microreactors cannot be applied to all chemistries yet and microfluidic systems also have disadvantages. Limited reaction time ranges, high sensitivity to precipitating products, and analytical challenges have to be over-

P.H. Seeberger, K. Geyer, J.D.C. Codée

2

come. An overview of microfluidic devices available for chemical synthesis is provided and some specific examples, mainly from our laboratory, are discussed to illustrate the potential of microreactors.

1

Introduction

Synthetic chemists typically perform transformations in roundbottomed flasks on a scale ranging from several milligrams to many grams, in reaction volumes from less than one milliliter to several liters (Geyer et al. 2006; Flögel et al. 2006). The optimization of chemical transformations consumes considerable amounts of starting materials and often takes a lot in order to identify ideal reaction conditions. Having found the optimal conditions to achieve a certain reaction on a small scale, process scale-up often poses additional challenges and requires further adjustment of the reaction parameters. To overcome these hurdles in synthetic chemistry, microstructured continuous-flow reactors and chip-based microreactors are becoming increasingly popular. The term “microreactor” is generally used to describe microstructured reactors. In fact, the reactors are often a lot bigger than the term “microreactor” suggests, having internal volumes of several milliliters. So far microstructured reactors have found most applications in process and development chemistry. Chip-based microreactors incorporate much smaller channels and are therefore more suitable for synthetic purposes in an academic setting. The small dimensions of microreactors allow for the use of minimal amounts of reagent under precisely controlled conditions and make it possible to rapidly screen reaction conditions and improve the overall safety of the process. To obtain synthetically useful amounts of material, the reactors are simply run longer, the so-called scale-out principle (Thayer 2005). Alternatively, several reactors are placed in parallel (numbering up), ensuring identical conditions for the analytical and preparative modes. Reviews on different aspects of microreactor chemistry have appeared (Thayer 2005; Ehrfeld et al. 2000; Fletcher et al. 2002; DeWitt 1999; Jähnisch et al. 2004; Watts and Haswell 2005; Pennermann et al. 2004; Jensen 2001; Kiwi-Minsker and

Microreactors as Tools in the Hands of Synthetic Chemists

3

Renken 2005; Hessel et al. 2005a, b; Golb and Hessel 2004; Kockmann et al. 2006). Here, some concepts and recent developments relevant to synthetic chemists will be summarized. Microreactor technology is beginning to be used in the fine chemical and pharmaceutical industries (Hessel et al. 2005b), and several success stories have been reported already (Thayer 2005; Rouhi 2004).

2

Microfluidic Reactor Types

Microreactors consist of a network of miniaturized channels, sometimes embedded in a flat surface, referred to as the chip (Ehrfeld et al. 2000; Cooper et al. 2001; Fletcher and Haswell 1999). A variety of reactors have been explored and some reactors are now commercially available. Different applications call for different types of reactors. The size as well as the chemical and physical properties of the material used for reactor construction and the mode of reagent and solvent introduction to the system influence the field of use for different reactors. The features of some microreactors are summarized in Fig. 1. [A wide variety of other microreactors is available from other manufacturers and suppliers, e.g., Institute for Microtechnology Mainz (IMM), Fraunhofer Alliance for Modular Microreaction Systems (FAMOS), the New Jersey Center for MicroChemical Systems (NJCMCS), the MicroChemical Process Technology Research Association (MCPT). The selection presented here is by no means exhaustive and only serves to indicate the diversity in systems developed to date.] Glass, silicon, stainless steel, metals, and polymers have been used to construct microreactors (Ehrfeld et al. 2000; Manz et al. 1991). Glass has traditionally been the most popular material for synthetic chemists since it is chemically inert to most reagents and solvents. The transparency of glass enables the visual inspection of reactions and fabrication procedures are well established (Watts and Haswell 2005; McCreedy 2000; Fletcher et al. 1999). The commercially available AFRICA microreactor system for example can be equipped with glass reactors of different sizes (60 µl, 250 µl, and 1.0 ml) (Syrris 2006). Silicon has also found widespread use in the construction of microreactors, since methods developed for semiconductor chip production can

4


Fig. 1a–e. Selected microreactors. a Stainless steel microreactor system designed by Ehrfeld Mikrotechnik. b Glass microreactor (Watts and Haswell 2005). c Stainless steel microreactor of the CYTOS Lab system (http://www.cpc-net.com/cytosls.shtml). d Silicon-based microreactor designed by Jensen (Ratner et al. 2005). e Glass microreactor of the AFRICA System

be readily applied to create a variety of three-dimensional architectures (Jensen 2001; Lu et al. 2001; de Mas et al. 2002). Oxidized silicon, like glass, is chemically inert to most reagents and solvents. The excellent thermal conductivity of silicon allows for microreactors to be constructed with outstanding heat-transfer capabilities. Exothermal reactions as well as reactions that require very high or low temperatures benefit from silicon microreactors (Ratner et al. 2005). Stainless steel is the material of choice for process chemistry. Consequently, stainless steel microreactors have been developed that include complete reactor process plants and modular systems. Reactor configurations have been tailored from a set of micromixers, heat exchangers, and tube reactors. The dimensions of these reactor systems are generally larger than those of glass and silicon reactors. These meso-scale reactors are primarily of interest for pilot-plant and fine-chemical applications, but are rather large for synthetic laboratories interested in reaction screening. The commercially available CYTOS Lab system (CPC 2007), offers reactor sizes with an internal volume of 1.1 ml and 0.1 ml, and modular microreactor systems (internal reactor volumes 0.5 ml to


5

11.0 ml) are offered by Ehrfeld Mikrotechnik (Ehrfeld Mikrotechnik BTS 2007). The different types of microreactors for this reactor system include capillary and cartridge reactors. IMM provides a variety of stainless steel microreaction systems including micromixers, heat exchangers and reactors for multiphase reactions. Polymer-based microreactor systems [e.g., made of poly(dimethylsiloxane) (PDMS)], with inner volumes in the nanoliter to microliter range (Hansen et al. 2006), are relatively inexpensive and easy to produce. Many solvents used for organic transformations are not compatible with the polymers that show limited mechanical stability and low thermal conductivity. Thus the application of these reactors is mostly restricted to aqueous chemistry at atmospheric pressure and temperatures for biochemical applications (Hansen et al. 2006; Wang et al. 2006; Duan et al. 2006).

3

Flow Types and Introduction of Solvents and Reagents

Fluids can be moved through the channels of microreactors using hydrodynamic pumping, electrokinetic pumping, or capillary flow. The most straightforward approach to operate a microreactor from the synthetic chemist’s point of view is to drive solutions through the reactor by hydrodynamic pumping. Flow speeds from microliters per minute to liters per minute can be achieved by using either syringe or HPLC pumps. In glass microreactors, fluids can be immobilized using electroosmotic flow (EOF), whereby a voltage is applied to the reagent and collection reservoirs. This mode of “pumping” has certain advantages over hydrodynamic pumping as it involves no moving parts and can be readily miniaturized and carefully computer controlled. However, EOF requires polar solvents, depends on the solute concentration, may cause unwanted electrochemical transformations and/or separations and can only be applied to analytical scale reactors. Capillary flow techniques are also of limited use in organic synthesis. Although precise control over fluid amounts can be achieved, the volumes transported through the capillary reactors are very small (DeWitt 1999; Nikbin and Watts 2004).

6


Independent of the mode of pumping, the flow inside the channel network of chip-based microreactors is generally laminar and the mixing of reagents occurs by diffusion. Given the small dimensions of the devices, diffusion is generally very efficient, and mixing is effected within milliseconds.

4

Synthesis in Microchemical Systems

Due to the small dimensions and the increased surface-to-volume ratio of microreactors, mass and heat transport are significantly more efficient than in the classical round-bottomed flask. The mixing of reagents by diffusion is very fast, and heat exchange between the reaction medium and reaction vessel is highly efficient. As a result, the reaction conditions in a continuous-flow microchannel are homogenous and can be precisely controlled. Highly exothermic and even explosive reactions can be readily harnessed in a microreactor. The careful control of reaction temperature and residence time has a beneficial effect on the outcome of a reaction with respect to yield, purity, and selectivity. Below, some examples, mainly from our laboratory, are described to illustrate the potential application of microreactors to organic synthesis. The application of microreactors to small-scale medicinal and academic total synthesis is just beginning.

5

Liquid Phase Reactions

A wide range of liquid phase reactions have been performed in microreactor devices, such as Grignard reactions (Taghavi-Moghadam et al. 2001), nitrations (Rouhi 2004; Doku et al. 2001), glycosylations (Ratner et al. 2005; Geyer and Seeberger 2007), olefinations (Skelton et al. 2001a,b; Snyder et al. 2005), peptide-couplings (Watts et al. 2001, 2002a,b) aldol reactions (Wiles et al. 2002), epoxidations (Snyder et al. 2005), multicomponent reactions (Acke et al. 2006), and Swernoxidations (Kawaguchi et al. 2005), Liquid phase reactions carried out in microstructured devices benefit from the efficient mass and heat transport characteristics of microreactors and the fact that only small amounts of the reactants are in the system at any given time. In general, reac-


7

Scheme 1. Glycosylations in a microreactor

tions performed in microreactors should be reasonably fast and should not produce precipitating products or by-products that might clog up the reaction channel. Our laboratory focused initially on the use of microreactors for reaction optimization of glycosylation reactions (Scheme 1). In general, glycosylations are very challenging, since their stereochemical outcome depends on a wide variety of factors, such as the nature of the coupling partners, temperature, solvent, and concentration. Furthermore, the building blocks used for oligosaccharide assembly often require multistep syntheses and are precious synthetic intermediates themselves. Using a Jensen silicon microreactor system, the reaction progress of the coupling between mannoside 1 and galactoside 2 was monitored as a function of temperature and time (Ratner et al. 2005). It was revealed that at low temperatures (–80°C to –70°C) and short reaction times (96% 100% conversion, < 5% by-product 30 min 76% 90% 10% by-product 240 min 81% 275 min 74%

95% 5% by-product, clogged lines 85% >10% by-product

140

H. Lehmann

for 10 min. After a cooling down period of 18–20 min, the precipitated product was isolated by simple filtration in 76% yield but also 10% of the by-product was formed under these conditions. The overall processing time, which includes heating, maintaining the temperature for 10 min, and cooling, was only 30 min. In contrast to this, conversion of a reaction volume of 400 ml in the Voyager SF took roughly 4 h (entry 4) because eight cycles on a 50ml scale were necessary to convert this volume. Each cycle consisted of adding the starting material, heating, maintaining the temperature for 15 min, cooling, and removing the mixture from the reaction vessel, requiring a total of 30 min. Furthermore, when the mixture was pumped out of the vessel after the reaction, precipitation of the product clogged the outlet tube and a valve, so that the process had to be interrupted manually. For comparison, the reaction was also carried out in an autoclave (1 l volume, entry 5). Because of the long heating and cooling process, processing time in total was 275 min, leading to a product in 74% yield that contained more than 10% of the by-product.

3.2

Model Reaction 2

Scheme 2 shows a substitution reaction which is often carried out with solid carbonate in suspension, which is easily removed after reaction by a simple filtration. This reaction was chosen not only to test the handling of suspensions, but also to investigate the influence of different solvents on selectivity and work-up. The results are shown in Table 3.

Scheme 2. Reaction 2

Scale-Up in Microwave-Accelerated Organic Synthesis

141

Table 3 Result of reaction 2 under various conditions Entry

1 2

3

4

5

6

Batch size Conv. heating Conv. heating

20 ml

Solvent temp., time

CH3 CN, reflux, 6 h 20 ml DMSO, 150°C, 10 min µW, Emrys 15 ml CH3 CN, optimizer 150°C, 10 min µW, 4×50 ml CH3 CN, Synthos 150°C, 3000 10 min µW, 300 ml CH3 CN, Voyager SF 150°C, 10 min Autoclave 200 ml CH3 CN, 150°C, 10 min

Process Isol. Purity Remarks time yield 6h 76% 30 min 60 min 57%

dark purple crystals 65% Mix of product and by-product isolated 17 min 98% >96% Yellow crystals 25 min 78% >96% In a second trial 73% yield isolated Inlet tube clogged 280 min 92%

92% 8% by-product

Under conventional conditions in the lab (acetonitrile, reflux for 60 min) the product was isolated in 86% yield but starting material remained, revealing that the reaction was not complete. Prolongation of the reaction time to 6 h led to full conversion of the starting material, but also to reduced yield and to dark purple crystals (entry 1). Performing the same reaction in DMSO at higher temperature (150°C for 10 min) led to a significantly shorter reaction time, but also to increased formation of by-product and to a significant lower yield (entry 2). In contrast, when a microwave reactor was used at 150°C for 10 min, an isolated yield of 98% was achieved (entry 3). Scale-up trials then were done in the Synthos 3000, where the suspension was reacted without problems. In order to check reproducibility, two identical batches were carried out: the first batch giving 78% yield (entry 4) and the second giving 73% yield after crystallization. When the same reaction was done in an autoclave, a grey product, containing 8% of by-product, was isolated in

142

H. Lehmann

92% yield but with low quality (entry 6). Using the Voyager SF for this reaction failed, because the system was not able to pump the suspension into the reaction vessel (entry 5). Although we used finely ground potassium carbonate, the inlet tube was repeatedly blocked by the solid carbonate. It should also be mentioned that in terms of processing time, the reaction in an autoclave required 280 min, whereas in the Synthos 3000 only 25 min were needed to do the conversion. 3.3

Model Reaction 3

Scheme 3 illustrates the third model reaction was homogenous, and again we intended to compare conventional heating with microwave heating, as well as study the influence of different solvents on both. The obtained results are shown in Table 4.


Two different typical work-up procedures were applied in order to demonstrate the influence on the yield. Work-up A: The reaction mixture was poured into water and extracted with DCM. The organic phase was evaporated and crude product was purified by flash chromatography. Work-up B: The reaction mixture was poured into water. The precipitated product was filtered, washed, and dried. Under reflux conditions on a small scale in acetonitrile, the reaction was complete only after 24 h (entry 1). In a microwave reactor at 150°C, 86% isolated yield was achieved after 20 min reaction time (entry 2). Running the same reaction in DMSO or DMF at 150°C gave complete conversion of starting material, but because of losses during work-up, isolated yield was lower (entries 3 and 4). For scale-up trials, the Voyager SF was used, and the reaction was performed at 180°C for 20 min


143

Table 4 Results of reaction 3 Entry

1

2

3

4

5

Batch size

Solvent Process Isol. Purity Remarks temp., time yield time

CH3 CN, 97% >97% Reaction reflux, completed, 24 h work-up A µW, Emrys 15 ml CH3 CN, 28 min 86% >97% Reaction optimizer 150°C, not completed, 20 min work-up A colorless crystals Conv. 20 ml DMF, 50 min 60% >99% Work-up B heating 150°C, brownish crystals 20 min Conv. 20 ml DMSO, 50 min 63% >99% Work-up B heating 150°C, beige crystals 20 min 72% 95% Work-up B µW, 5×50 ml CH3 CN, 2 h Voyager SF 180°C, 40 min colorless crystals 20 min Conv. heating

20 ml

in each cycle. To process a 250 ml batch, five cycles of 50 ml each had to be performed, leading to a processing time of 2 h 40 min (entry 5). A typical diagram of temperature, pressure and time of all five runs is shown in Fig. 3. The temperature rises very rapidly to 180°C and is held for 20 min, the pressure during the reaction is approximately 11 bar. Then the vessel is cooled by air ventilation to about 60°C within 8–10 min. In total, this results in a cycle time of about 32 min for each cycle. 3.4

Discussion of the Results from Model Reactions

Two different microwave reactors for scale-up have been tested with special focus on handling, automation, workflow, and typical scale-up issues. The Synthos 3000 as a batch mode reactor provides a relatively large reaction volume (16 × 70 ml), allows high temperature and pressure (240°C/40 bar), and proved to be very robust. Handling of suspen-

144

H. Lehmann

Fig. 3. Diagram of reaction 3, Voyager SF

sions gave no problems and the system was shown to have very good temperature control. The software is easy to handle and results from the small scale were reproduced on a larger scale without additional optimization effort. Nevertheless, for synthesis on a large scale, filling and removing the contents of all 16 vessels is laborious and the cooling period is comparatively long. The reactor tested does not allow the handler to run several reactions sequentially in an automated manner. Automation of this type would be a highly desirable option in order to optimize the work-flow in a kilo lab. The possibility for automation is offered by the Voyager SF with its stop flow system, able to process larger reaction volumes by sequen-


145

tially repeating reactions on a 50-ml scale. The relatively small reaction volume guarantees a low safety risk on one hand, but on the other hand leads to relatively long processing times. Handling of suspensions also proved to be a critical issue and, in one case, precipitated product blocked the outlet tube and valves. Running reactions for a longer period without monitoring, for example overnight, can only be therefore recommended for homogeneous reaction mixtures.

4

Examples for Scale-Up Using Microwaves

In the course of our daily business in the kilo lab, we are faced with the preparation of a number of intermediates or drug candidates on a larger scale in which at least one step of the original synthesis was performed in a microwave reactor. In order to increase the productivity, it is of great interest to reduce the time needed to produce these compounds on a large scale. Reactions taking a long time at elevated temperature are targets for improvement in work-flow using microwave technology. 4.1

Example 1

In Scheme 4 it can be seen that cyclisation of the ketoester with hydrazine-hydrate was part of a reaction sequence given to the kilo lab and is described in literature with a yield of approximately 60% (Schenker and Salzmann 1979). Under conventional conditions (refluxing in ethanol for 4 h), we obtained the product in 53% yield. Performing the same reaction in the Synthos 3000 microwave reactor at 140°C for 20 min, we improved the yield to 64% on a 20-g scale. Further scale-up to a batch size of 130 g of product was performed under the same conditions (140°C/20 min) with no significant problems.


146

4.2

H. Lehmann

Example 2

A well known standard procedure in organic chemistry is to form pyrazoles via the reaction of β-ketonitriles with hydrazines. The reaction shown in Scheme 5 is part of the synthesis of a p38 MAP Kinase Inhibitor from Boehringer Ingelheim. In the literature, this reaction is described as giving a yield of 60%–85% after reflux in toluene for 24 h (Regan et al. 2002). Instead of toluene, we used methanol as a solvent and obtained a yield of 92% after 3 h of reflux. Using microwave conditions (120°C, 15 min), we scaled up the reaction from the 20-g scale to the 65-g scale, obtaining 86% yield and reducing the reaction time significantly from hours to minutes.


4.3

Example 3

Substitution of halogens on heteroaromatic rings is a common way to introduce new functionalities. The product from reaction 6 (Scheme 6) was required on a 100-g scale as an intermediate. In the literature, this exchange was done on a 5-g scale using ammonia in ethanol in a sealed tube under pressure for 6 h at 125–130°C with a yield of 76% (Bendich et al. 1954). Because of the lack of a suitable autoclave for high-pressure reactions, we choose the microwave reactor for scale-up trials. Using our Synthos 3000 equipment, we found suitable conditions with only minimal optimization at 170°C for 180 min and obtained the desired product on a 60-g scale in 83% yield.


147


5

Summary

The current study was initiated to evaluate the scalability of microwave technology. The prerequisites for a productive application of microwaveassisted synthesis on a larger scale in a kilo lab were defined, and a market survey for suitable microwave reactors from commercial suppliers was performed. In a second step, model reactions were selected and microwave systems designed for large-scale operation (Synthos 3000 and Voyager SF) were evaluated under realistic conditions in the kilo lab. Special focus was on temperature/pressure limits, handling of suspensions, robustness toward different kinds of chemistry, ability for fast heating and cooling, and the overall processing time. For comparison, some reactions were also performed in an autoclave. Strengths and weaknesses of each instrument were evaluated. In various experiments, it was shown that the use of microwave technology leads to a significant decrease in the reaction time and in some cases also to less by-product and a higher yield. This technology allowed us to optimize the reaction with focus on work-up and purification, independent of reaction temperature and boiling point of the solvent. In most cases the reaction conditions, applied on 15 ml scale in the Emrys Optimizer, were transferred without further optimization to the microwave reactors tested and led to comparable results. Additional optimization in a few cases was limited to small adjustments in reaction temperature or reaction time. A number of scale-up experiments were conducted using a Synthos 3000 reactor and we showed that a scale-up to 100 g is feasible. A major weakness of the available systems, however, is the limited vessel size, which in most cases is far below the volume required in a kilo lab of at least 1 l.

148

H. Lehmann

In theory, conditions in a microwave reactor, with regard to temperature and pressure, should also be attainable by using an autoclave. Some reactions were therefore done in an autoclave for comparison. The main difference proved to be the longer processing time, mainly caused by the long heating and cooling period when using an autoclave. This leads, as shown in example 2 of our study, to a different selectivity and to a significantly higher amount of by-product, which as a consequence had to be separated by additional purification steps. In this case, using microwave heating is obviously more advantageous than using an autoclave. In general, it should be noted that the commercially available microwave devices for scale-up were developed either from older existing systems for digestion (e.g., Synthos 3000, Anton Paar) or were completely developed new for synthesis on a larger scale (e.g., Advancer, Biotage). Some of these tools are more or less in a prototype phase where further development is ongoing. As this study revealed, the first steps of microwave technology toward scale-up in larger than the-100 g scale are complete, but in order for this to become a standard technology for kilogram-scale synthesis, further improvements with regard to reaction volume and automation will need to follow in the future Acknowledgements. The author thanks Biotage (Uppsala, Sweden), Anton Paar (Graz, Austria), and CEM Corp. (Matthews, NC, USA) for their support and for the possibility to test their microwave reactors in the kilolab. He also thanks all the colleagues and people who were involved in this project for their input and the challenging discussions.

References Bendich A, Russell P, Fox J (1954) The synthesis and properties of 6-chloropurine and purine. JACS 76:6073–6077 Kappe O, Stadler A (2005) Microwaves in organic and medicinal chemistry. Whiley-VCH, Weinhein, Germany Kappe O (2004) Controlled microwave heating in modern organic synthesis. Angew Chem Int Ed 43:6250–6284 Kappe O, Stadler A, Dallinger D (2003) Scalability of microwave-assisted organic synthesis. Organic Process Res Dev 7:707–716


149

Nicewonger R, Baldino C, Evans M (2003) The accelerated development of an optimized synthesis of 1,2,4-oxadiazoles. Tetrahedron Lett 44:9337–9341 Ondruschka B, Nüchter M, Bonrath W (2004) Microwave assisted synthesis— a critical technology overview. Green Chem 6:128–141 Regan J, Breitfelder S Cirillo P (2002) Pyrazole urea-based inhibitors of p38 MAP kinase: from lead compound to clinical candidate. J Med Chem 45:2994–3008 Schenker E, Salzmann R (1979) Antihypertensive action of bicyclic 3-hydrazinopyridazines. Arzneimittel-Forschung 29:1835–1843

Reading List Anton Paar Corporate Website (2007) www.anton-paar.com. Cited 5 February 2007 Biotage (2007) www.biotage.com. Cited 5 February 2007 Cemsynthesis (2006) www.cemsynthesis.com. Cited 5 February 2007 Kappe O (2007) Christian Doppler Institute for Microwave Chemistry, University of Graz, www.maos.net. Cited 5 February 2007 Milestone Microwave Laboratory Systems (2003) www.milestonesci.com. Cited 5 February 2007


Solid Supported Reagents in Multi-Step Flow Synthesis I.R. Baxendale, S.V. Ley(u) Innovative Technology Center (ACS), Department of Chemistry, University of Cambridge, CB21EW Cambridge, UK email: [email protected]

1 Introduction . . . . . . . . . . . . . . . . . . 2 Solid-Supported Reagents . . . . . . . . . . . 3 Flow-Based Integration of Supported Reagents 4 Flow-Based Chemical Synthesis . . . . . . . 5 Natural Product Synthesis . . . . . . . . . . . 6 Conclusion . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

. . . . . . .

152 153 158 162 172 178 179

Abstract. The frequently overlooked benefits that considerably simplify and enrich our standard of living are most often hinged upon chemical synthesis. From the development of drugs in the ongoing fight against disease to the more aesthetic aspects of society with the preparation of perfumes and cosmetics, synthetic chemistry is the pivotally involved science. Furthermore, the quality and quantity of our food supply relies heavily upon synthesised products, as do almost all aspects of our modern society ranging from paints, pigments and dyestuffs to plastics, polymers and other man-made materials. However, the demands being made on chemists are changing at an unprecedented pace and synthesis, or molecular assembly, must continue to evolve in response to the new challenges and opportunities that arise. Responding to this need for improved productivity and efficiency chemists have started to explore new approaches to compound synthesis. Flow-based synthesis incorporating solid supported reagents and scavengers has emerged as a powerful way of manipulating chemical entities and is envisaged to become a core laboratory technology of the future.

I.R. Baxendale, S.V. Ley

152

1

Introduction

Flow-based applications of chemical synthesis have existed for many decades (Karnatz and Whitmore 1932; Dye et al. 1973). Unfortunately, although the concepts of increased mixing efficiency, controlled scaling factors, enhanced safety ratings and continuous processing capabilities have all been well recognised, these benefits have not been generically leveraged into conventional synthetic chemistry. Indeed, traditionally almost all chemical manipulations have been conducted as sequences of well-defined and laboriously optimised single-step transformations operated in batch mode. Consequently, the majority of process innovations in terms of new tools and techniques that have helped define modern organic synthesis have been based on modifications to existing batch-processing protocols. It is certainly true that some of these technological changes have had a significant impact on the way chemists approach and prepare their compound collections. One such methodology which has impacted widely throughout the chemical industry has been the adoption of solid supported reagents and scavengers as effectors of chemical change and subsequent reaction purification (Ley et al. 2005; Baxendale et al. 2003; Kirschning et al. 2001; Bhattacharyya 2000, 2001; Sherrington 2001; Ley et al. 2000; Thompson 2000; Shuttleworth et al. 2000; Booth and Hodges 1999; Parlow et al. 1999; Drewry et al. 1999; Hodges 1999; Booth and Hodges 1997; Shuttleworth et al. 1997; Kaldor et al. 1996; Chakrabarti and Sharma 1993; Akelah and Sherrington 1981, 1983). However, the advantages provided by utilising these immobilised species have only been partially realised through their application in batch-based chemistries, additional attainable gains can be derived when these agents are incorporated into flow-based synthetic applications. A few general comments concerning the nature of these immobilised species and their potential application in synthesis are probably pertinent at this stage. Firstly, artificially immobilising a reagent in order to conduct chemical syntheses is not a new concept, having been first reported in 1946 (Sussman 1946). However, tremendous advances have been made in this field, and our group in particular has sought to develop the application of immobilised systems to complex synthetic challenges such as multi-step integrated synthetic operations (Baxendale and Ley

Solid Supported Reagents in Multi-Step Flow Synthesis

153

2005; Ley et al. 2001, 2002a, 2002b; Ley and Baxendale 2002a,b; Baxendale et al. 2002; Ley and Massi 2000; Caldarelli et al. 1999a, b, 2000; Habermann et al. 1999a; Habermann et al. 1999b; Hinzen and Ley 1998). Such a philosophy based on continuous sequential or parallel processing of reactants often involving several stages of reactive intermediates has naturally led us to an investigation of such transformations in terms of dynamic coupled multi-step continuous flow procedures (Baxendale et al. 2006a,b,c,d; Saaby et al. 2005).

2

Solid-Supported Reagents

In general terms, supported reagents are reactive species that are associated with a support material and are used to transform a substrate (or substrates) into a new chemical product (or products). A key advantage is that it is possible to use an excess of the reagent to drive a reaction to completion and then as the work-up is simplified by the reagent immobilisation, the product can be isolated cleanly (Fig. 1). Additionally, in situations where highly toxic or obnoxious materials must be used, by virtue of the attachment process, such unpleasant compounds can be rendered easier to manipulate and recover, and therefore safer. Likewise, the immobilisation of expensive catalysts and ligands greatly facilitates their recycling potential. Furthermore, immobilisation intrinsically results in reagents becoming site-isolated, that is the immobilised reagents are able to react with substrates in a solution but not readily with one another. This means multi-reagent processes such as oxidation and reduction or other mutually incompatible transformations can be conducted simultaneously in single reaction vessels. This is an ex-

Fig. 1. Basic concept of solid supported reagents

154


tremely attractive concept and constitutes a significant shift in the way we perceive reactions or plan a chemical synthesis. However, not all reactions give entirely clean products, but by using supported reagents, by-products and unwanted components can also be scavenged, which obviates the need for more conventional and often more expensive or wasteful procedures such as chromatography, distillation or crystallisation. Purification can also be achieved through the addition of solid-bound species that are programmed to only recognise the target product. This of course is not a serendipitous process but requires specific chemical design. Products can then be captured and impurities washed away before being re-released to give clean compounds, a procedure otherwise known as the catch-and-release technique. Effective syntheses, convergent as well as batch-splitting, are possible using these methods, which can provide both combinatorial arrays and fragment sets of new molecules (Fig. 2). The act of immobilisation can be accomplished in a variety of ways such as on beads, active

Fig. 2. Application of solid supported reagents


155

surfaces, colloids, dendrimers, plugs, and laminates. For each of these formats, there is also a variety of support materials available, e.g. polymers, cellulose and silica gels enabling a large selection of reagents to be built. Utilising these supported reagent procedures has permitted the syntheses of many complex natural products (Ley et al. 2006) to be completed, including the epothilones A and C (Storer et al. 2003, 2004) carpanone (Baxendale et al. 2001, 2002b) and various members of the amaryllidaceae alkaloids family, namely oxomaritidine, epimaritidine (Ley et al. 1999) and plicamine (Baxendale and Ley 2005b; Baxendale et al. 2002c,d) (Fig. 3). In addition, it has been possible to devise protocols to prepare specific drug molecules as well as generate derivatives and analogues of a diverse range of these pharmaceutically interesting compounds (Baxendale and Ley 2005c; Baxendale et al. 2002e,f, 2005; Siu et al. 2004; Baxendale and Ley 2000). As an example of the sophistication that can be achieved using solidsupported reagents in multi-step applications (+)-plicamine (Baxendale and Ley 2005b; Baxendale et al. 2002b,c) truly stands out (Scheme 1). In this synthesis, extensive use was made of parallel optimisation methods in order to progress the forward route more rapidly. The incorporation of focussed microwave techniques also aided in achieving faster and cleaner reactions. Indeed, the whole route, including optimisation, was completed in just 6 weeks, without resorting to any form of traditional separation or purification. When conducting such syntheses, the immobilised reagents can be delivered in a variety of formats, most commonly their physical form is as loose beads, or as beads contained within pouches or formed into composite plugs. Unfortunately, the commonly used micro-bead reagent configuration is not always the most practical of materials to work with. Measuring and dispensing operations are often associated with problems of static charge and calibration of the stoichiometry. Additional difficulties can also be encountered during the reactions with possible fragmentation and grinding of the beads, which can complicate the work-up protocol. Another issue often highlighted is one of product recovery, which may involve extensive washing of the support in order to fully extract the desired molecules. However, the same reagents can be readily packed into tubes, cartridges and various flow assemblies re-

156


Fig. 3. Natural products and derivatives accessed through solid supported reagent technology


Scheme 1. Synthesis of the natural product (+)-plicamine

157

158


Fig. 4. Assembly of columns using solid supported reagents

sulting in tremendous versatility; particularly so for complex molecule assembly where rapid reaction and reagent optimisation is essential for efficient and high yielding production (Fig. 4).

3

Flow-Based Integration of Supported Reagents

Flow-based chemistry in this context provides the chemist with a new synthesis platform that expands the current capabilities and opportunities available, providing improved safety considerations, enhanced dispensing and mixing coefficients, and real-time diagnostics with the ability to make changes on the fly in a dynamic fashion. As a technique, it replaces traditional glassware with preloaded columns and cartridges containing immobilised reagents and catalysts, also incorporating precision-manufactured reaction chips that permit controlled mixing and precise temperature control of reaction sequences. This essentially transforms conventional batch reaction sequencing into a flowing, dynamic processing procedure by either passing the starting materials through various immobilised reagents or combining intermediates and


159

reagents in specialised reactor blocks in predefined combinations. In this way, the intermediate material generated in situ can be subjected to a series of reaction cascades and scavenging protocols before it eventually exits from the reactor into a chemically inactive environment allowing for its immediate collection as a pure product. Throughout this processing, the packed cartridges can be interacted upon by various physical means such as heating/cooling, oscillation, ultrasound, microwaves or irradiation. Flow chemistry (Luckarift et al. 2005; Doku et al. 2005; Kirschning and Jas 2004; Jönsson et al. 2004; Jas and Kirschning 2003; Watts and Haswell 2003a, 2003b; Fletcher et al. 2002; Hafez et al. 2000, 2002; Hafez 2001; Anderson 2001; Sands et al. 2001; Haswell et al. 2001; Ehrfeld et al. 2000) can also facilitate processes that are not feasible (or at least very technically challenging) by conventional methods, such as the generation and concurrent use of potentially highly reactive or unstable intermediates. In addition, the incorporation of automated and real-time analysis facilitates rapid optimisation and excellent quality control whilst also ensuring reproducibility. By accurate control over flow rates, reactant concentrations, temperatures and pressures, these information-rich sequences generate opportunities for highly responsive modification of chemoselective processes and constitute a paradigm shift for delivery of new chemical entities. Existing supported reagent technology integrates well into such a synthesis foundation. The extensive range of reagent formats from traditional silica or polymer microbeads through to woven fibers, pressed disks and monolithic structures can all be rapidly customised for use in such flow reactor designs. The development of a diverse tool kit of such functionalised materials can then be combined to facilitate multi-step synthetic sequences. For example, used in series the reaction cartridges could be arranged such that a multitude of reactions could be carried out on each substrate (a splitting of the reaction flow approach), possibly with further monomer inputs at different points allowing access to multiple products (Fig. 5). Alternatively, when used in parallel the reactor arrays could be sequenced for the production and purification of very large libraries of compounds. Clearly, this is an area that is ideally suited to supported reagents, as synthesis in this format is hard to envisage using any other technique since purification on this scale,

160


Fig. 5. Flow chemistry principles

whilst not impossible, would make parallelisation prohibitively expensive. Another value-added consequence of working in a flow mode is the extensive information that can be harvested from the reaction as attained from real-time in-line analysis. Such prospecting can yield extensive information regarding the reaction parameters, allowing rapid optimisation as well as important kinetic and physical chemical data to be archived. Such sampling techniques can be both passive and semiinvasive in nature. Rapid although limited qualitative spectral data can be easily acquired through adjustable wavelength photodiode detectors (or similar spectrometers), which can be assembled as in-line analysis cells or by using the appropriate construction materials can take readings directly through the reactor walls (or connective tubing). Other diagnostic devices can also report on reaction progress using techniques such as impedance measurements, Raman spectroscopy, near or React IR, fluorescence measurements and various bioassays. Alternatively, or in addition, automated sampling techniques can be used to divert small


161

but representative aliquots of the reaction media from the main stream into auxiliary monitoring equipment. This allows powerful techniques such as LC-MS or GC-MS to be assimilated into the system, providing another level of diagnostic capability. Fundamentally, as each stage of the reaction can be considered spatially isolated from the material proceeding and following it—segmented flow analysis—altering the conditions at any point in the continuum will ultimately allow a contrast at later stages of the reaction’s pathway. Thus it becomes a simple task to automatically cycle through various reaction parameters in order to evaluate such effects on the reaction composition and purity. However, a cautionary note should be made regarding how this information is ultimately measured and interpreted depending on whether the reactor is working in a plugged or steady-state operation. Although sequential plugged reactions can exhibit similar characteristics to those that achieve steady state, the material progressing though the system obviously does not experience the same conditions in terms of reagent concentrations or diffusion broadening. Acquiring this portfolio of reaction information is only the primary stage, effective information feedback and self-optimisation processes using design of experiment (DoE) and principal component analysis (PCA) are highly effective aids (Vickerstaff et al. 2004; Jamieson et al. 2000, 2002). Indeed, the large quantities of data that are captured from the monitoring processes can be directly analysed by such evaluation software, which can in turn be used to directly affect the subsequent operation of the reactor. Not only can this be used to rapidly and efficiently optimise a chemical transformation, but in combination with a flexible reactor design it can also be used to screen for catalyst or even discover new chemistries. Again, it should be emphasised that all this can be done in a fully automated fashion requiring only minimum human intervention following the reactor loading and configuration. It is important that these new technologies should not dominate nor distance the chemist from the synthesis; rather they should be utilised to liberate the chemist from the more mundane and repetitive operations allowing them to reallocate time to the more important tasks of thinking and planning.


162

4

Flow-Based Chemical Synthesis

Focussed microwave irradiation has always offered an effective mechanism for rapidly heating flow reactions, especially when employing heterogeneous components (Wison et al. 2004; Thomas and Faucher 2000; Kabza et al. 2000; Toteja et al. 1997; Zu and Chuang 1996). The precise control of energy that can be transposed to the sample as well as the highly adjustable temperature profile enables more judicious heating in the face of constantly changing flow rates and reactant concentrations. In a recent study of non-metal-catalysed intramolecular cyclotrimerisation reactions we demonstrated it was possible to conduct such chemistry as a flow process at elevated temperatures using a glass coil inserted into the microwave reaction cavity (Fig. 6) (Saaby et al. 2005). Gram quantities of material could thus be prepared by pumping a DMF solution of the precursor through the system heated at 200°C whilst maintaining reaction pressure by using a back pressure regulator. Interestingly, in the corresponding sealed batch system the decomposition of DMF used as the solvent led to the generation of significant pressures. Using a continuous flow process avoided this problem by restricting the residence time of the DMF and constantly balancing the internal pressure, thereby reducing the decomposition and any pressure increase. Microwaves have also proved useful for the preparation of various substituted pyrazole structures that are prepared in flow by using a modified tubing reactor inserted into the microwave well (Fig. 7). Several meters (10–15 m) of microwave transparent tubing could be tightly spiralled around a Teflon column manufactured to fit into the microwave and mimic the action of a normal batch microwave vial. Connecting the input of the reactor to a reactant reservoir via a HPLC pump and the output to a twin column assembly containing a polymeric primary amine scavenger and activated carbon decolouriser completed the system. This simple flow setup has been used for periods of 36 h at temperatures up to 150°C in order to prepare 15 g batches of bulk intermediates in high yields and excellent purities (Fig. 8). One of the obvious areas where flow chemistry comes into its own is in the arena of catalysed reactions and continuous processing. An excellent example of this is the Suzuki reaction (for recent reviews on the Suzuki Cross-Coupling reaction, see Miura 2004; Bellina et al. 2004;


163

Fig. 6. Intramolecular cyclotrimerisation reactions, equipment and glass microwave insert reactors

Pershichini 2003; Kotha et al. 2002), which is by far the most versatile synthetic method available for the generation of unsymmetrical biaryl compounds and so was an obvious target for the development of flow

164


Fig. 7. Insert microwave tubing reactor

Fig. 8. Column attachments for microwave cavity tubing reactor

reactor designs. The standard catalyst employed in this reaction is a palladium species; however, the reactions suffer from high levels of residual palladium contamination of the final products. We have previously reported a polyurea microencapsulated palladium catalyst (Pd EnCat™;


165

Fig. 9), which has been applied to a range of cross-coupling and reduction reactions (Pd EnCat™ 30 available from Aldrich 644714-XXXG [XXX = 1, 10, 100 with regard to batch size] loading: 0.4 mmol/g Pd; Yu et al. 2003; Ramarao et al. 2002; Ley et al. 2002; Bremeyer et al. 2002). This type of polyurea matrix is able to ligate and retain the palladium within the cavities of the microcapsule but permits the reactants to diffuse to the active catalyst and then allows the products to exit back into solution. Indeed, inductively coupled plasma (ICP) analysis of product mixtures has proven palladium levels to be less than 10 ppm corresponding to less than 1% leaching of the original palladium content of the capsules. Additionally, should leaching become a problem, further passage through a Quadrapure™ TU scavenging column leads to enhanced quality products. The Pd EnCat catalyst has been used in two sets of Suzuki coupling reactions in flow under very different reaction conditions. In a proof of concept study, it was shown that iodobenzene and p-toylboronic acid could be quantitatively coupled at 70°C when passed through a fixed bed of the Pd EnCat™ in the presence of an equivalent of the n Bu4 NOMe salt as a 9:1 Toluene/MeOH solution (Lee et al. 2005). The reaction was complete following only a single pass through the loaded HPLC column (5 × 0.45 cm ID) using a flow rate of 0.2 ml/min resulting in a mean residence time of approximately 4 min. In addition, the catalyst system could be recycled multiple times without any noticeable deterioration of the catalyst system. Such an example therefore aptly demonstrates the potential for process intensification that such a combination of novel technologies represent. Following on from this work, it was further demonstrated that microwave heating could be used to vastly expedite the production of Suzuki furnished compound arrays including the generation of multigram quantities of products in a single, continuous operation (Baxendale et al. 2006b). The reactor design used was based upon a simple continuous glass U-tube which was packed with the heterogeneous catalyst and inserted into the microwave cavity (Fig. 10). Stock solutions of the boronic acid, aryl halide and n Bu4 NOAc activator were prepared and constantly fed at a flow rate of 0.1 ml/min through the flow reactor that was resident in the microwave cavity (Fig. 11). This configuration gave a total residence time of 225 s for the reactor assembly, although

166


Fig. 9. Magnified Pd EnCat catalysts bead and high-resolution electron microscope image of the surface of the polyurea matrix


167

Fig. 10. Pd EnCat microwave reactor columns, simple U-tube and enclosed system

for only 65 s of this time was the solution present in the microwave cavity. As the reaction mixture exited the reactor chamber, it was progressed through a column of Amberlyst 15 sulfonic acid resin to remove any residual base and boronic acid salts. The solution could then be collected, and following evaporation the final product isolated without the need for further purification. Interestingly, applying a cooling stream of compressed gas to the U-tube reactor while maintaining the microwave irradiation was found to further enhanced the yield and purity of the process. Indeed, microwave heating has been shown to significantly improve the yields of reactions in which the reactants or products suffer from thermal decomposition because of the reduced reaction times and the more even application of energy (for general reviews on the use of microwave irradiation in organic synthesis, see Kappe 2004; Nüchter et al. 2004; Wathey et al. 2002; Wathey 2001). As an extension of this effect, techniques involving microwave irradiation in heat/cool cycles or pulsed power sequences used to limit the global temperature as well as using

168


Fig. 11. Reactor configuration for flow Suzuki reactions

external cooling have all generated products of significantly higher purity (Arvela and Leadbeater 2005; Leadbeater et al. 2005; Humphrey et al. 2003; Chen and Deshpande 2003). In theory immobilisation of the catalyst in such a packed column format permits an easy automated recycling process to be established. To validate this notion, the complete set of ten coupling reactions outlined in Table 1 were performed. Each substrate pairing was sequentially passed through the same reactor column without regeneration or replacement of the catalyst. The individual streams of substrates were separated using a blank solvent plug which also functioned to wash the catalyst bed before the next set of reactants arrived. Following this protocol, no cross-contamination of the products was detected. Clearly such a processing procedure is of intrinsic value to the high-throughput automated synthesis of compound libraries. In addition to the ability to prepare multiple products, it was also demonstrated that it was possible to scale-out the reaction using prolonged reaction times. In this way, multi-gram quantities of material could be readily isolated (Scheme 2). The reactions were very efficient


169

Table 1. Sequential processing of multiple substrates in flow [1 equiv. halide, 1 equiv. boronic acid, 2 equiv. Bu4 NOAc in EtOH. Flow rate 0.1 mL/min, 50 W with external cooling]

170


Scheme 2. Scaled synthesis of Suzuki reactions

progressing for several hours, after which the conversion dropped dramatically, finally deactivating the catalyst. In this process, the yields of products isolated correspond to an ultimate catalyst loading of as little as 0.2 mol%, which is exceptionally low for this type of catalyst. The high catalytic turnover and short residence times required are certainly a consequence of the high effective catalyst-to-substrate ratios encountered within the reactor. What emerges of considerable importance from this study is the demonstration that a single reactor design can be utilised both for library generation and scaled synthesis. Additional advantages in terms of substrate selectivity were also observed from the extremely short reaction times and mild reaction conditions. For example, the reactive 2-iodobromobenzene was used as a substrate because in the corresponding batch reaction with 2-benzofuran boronic acid, large quantities of the double addition product were detected (Scheme 3). However, when the same coupling was performed in flow, the reaction could be optimised so that boronic acid reacted only

Scheme 3. Enhanced selectivity in flow microwave reactions


171

at the iodide site, generating the single substitution product. This example of enhanced selectivity clearly demonstrates the additional synthetic scope that can be provided from working in a flow domain. This is particularly important when one considers the extended range of substrates that could be employed and the additional reaction sequences leading to increased molecular diversity that could be achieved. We have also employed conventional conduction heating techniques using modified heating blocks for both micro-channel reactor chips and packed glass columns (Fig. 12). In addition, our need for specific temperature control, which may differ for each stage of the reaction sequence, has been achieved using a dedicated column heater the Vapourtec R-4 (Fig. 12). Such equipment was used to great effect in the recent synthesis of a collection of 4,5-disubstituted oxazoles (Baumann et al. 2006). The reaction scheme involved the additional reaction of an isonitrile moiety to an acyl chloride followed by a base catalysed intramolecular cyclisation (Scheme 4). The chemistry was successfully optimised and the compounds repeatedly prepared on-demand using a bespoke automated modular flow reactor as described in Fig. 13. In total, 37 different compounds were synthesised in excellent yields (Fig. 14) in amounts ranging from 150 mg to 10 g of material. Apart from the introduction of a scavenging cartridge of Quadrapure™ BZA, a primary amine functionalised macroporous polymer, no further purification was required in order to isolate pure materials. The ability to carry out such chemical reactions at various scales in a controlled automated fashion further exemplifies the power of such processing procedures.

Fig. 12. Column heating block and Vapourtec R-4 Flow Reactor Heater


172

Scheme 4. Preparation of 4,5-disubstituted oxazoles

5

Natural Product Synthesis

So far throughout this article, a key principle has been the on-demand manufacture of advanced chemical materials from integrated multi-step sequences. Obviously, single-step chemical transformations have their place, and a rapidly growing literature base of such operations can also be uncovered in the recent chemical literature. However, the ultimate power of synthesis is in its ability to construct architecturally and individually tailored molecules of choice through multi-component, multistep operations. Consequently the adoption of flow-based synthesis will only really be truly accepted when it can supersede existing batch-based chemical processing techniques. It has therefore always been our aim to focus our attention on the more challenging end of flow chemistry investigations by evaluating extended synthetic routes to advanced final products. In this respect, we have investigated the synthesis of two complex natural products, grossamide (Baxendale et al. 2006a) and oxomaritidine (Baxendale et al. 2006c) as initial targets. The synthesis of grossamide (Baxendale et al. 2006a) is interesting because it brings together a number of concepts previously men-


173

Fig. 13. Schematic of microflow reactor system

tioned and also introduces the practice of using immobilised enzymes under continuous flow conditions. Although the overall complexity of this neolignan may indicate on first inspection a longer sequence of steps, in fact this compound was prepared via only two transformations (Scheme 5). By eluting a prepacked column of immobilised HOBt with a solution of ferulic acid and activator, the corresponding tethered activated ester could be formed. This allows excess starting material and byproducts to be washed from the column. This procedure was also used to great effect as an activation step and purification aid in the synthesis of sildenafil (Baxendale and Ley 2000). Next a solution containing an

174


Fig. 14. Oxazoles prepared using flow reaction conditions

amine-coupling agent was directed through the loaded column resulting in the formation of the coupled amide product. As these two sequences are distinct in nature, two parallel columns can be run in conjunction so that as one is loading to form the active ester the previously functionalised column is undergoing reaction to generate the desired product. Obviously, the two columns can be rapidly interconverted, thereby giving in essence a seamless continuous feed of the product. Directing this flow stream through a column of supported sulfonic acid removed any excess unreacted amine residues before it was mixed with a second solution containing hydrogen peroxide and a buffer. The combined reagent stream was then passed through a final column containing horseradish peroxidase enzyme which was trapped on a modified silica support. The resulting solution could then be collected and the product isolated. Although this reaction scheme only yielded a single product, it is easy to envisage similar reactions based on entirely unnatural coupling deriva-


175

Scheme 5. Flow synthesis of the natural product Grossamide

tives or the generation of extended routes yielding more elaborate structures. More advanced peptides have also been prepared in a similar automated flow sequence through sequential activation of the carboxylic motif in a linear fashion (Baxendale et al. 2006d). Initially a series of the protected dipeptides were generated (Table 2), but this process has now been extended to the formation of tripeptides (Scheme 6) and could easily be further modified to allow additional couplings. Our most significant challenge to date has been the synthesis of oxomaritidine as a flow-derived process. The Amaryllidaceae alkaloid oxomaritidine had been previously synthesised using both traditional solution-phase methodology (Schwartz and Holton 1970) and with the aid of polymer-supported reagents (Ley et al. 1999), making it an excellent benchmark for our evaluation. Indeed the time savings resulting from

176


Scheme 6. Sequence for the construction of tripetides


177

Table 2 Dipeptide structures prepared Entry

Protecting group

R

R1

R2

Isolated yield

1 2 3 4 5 6 7 8 9

Boc Boc Boc Boc Cbz Cbz Cbz Cbz Cbz

Me Me Me Me CH2 Ph Ch2 Ph Me Me Me

CH2 Ph H CHMe2 –(CH2 )3 – CHMe2 H CH2 Ph H –(CH2 )3 –

Et Et Me Me Me Et Et Et Me

80% 81% 83% 66% 79% 76% 75% 78% 61%

Scheme 7. Continuous flow synthesis of the natural product Oxomaritidine


178

the application of these flow-through methods in comparison to conventional procedures are dramatic. The synthesis time for the flow-through process to produce the natural product in an automated sequence from readily available starting materials was less than a day (Scheme 7). Originally, this synthesis had taken approximately 4 working days, including quenching procedures and column chromatography to purify the individual products at various stages. By streamlining the purification requirements using solid-supported reagent technology, it was possible to reduce this timeframe to around 2 days. Obviously, the use of the supported reagents grants a considerable productivity savings, although such procedures still involve a significant level of human intervention, as required by reaction monitoring and the filtration/washing steps. It should also be highlighted that although a certain degree of setting up time is required in the flow-through process, once the system is configured the equipment can function independently of the human operator. Therefore, it is easy to see why such protocols could revolutionise the working practices within most laboratories.

6

Conclusion

Commercial synthesis requirements are rapidly changing, generating an inherent need to conduct chemistry in a more efficient and timely manner. In addition, as the global emphasis towards more eco-friendly and sustainable practices unfolds before us, we are being required to reevaluate how chemical synthesis should be conducted. We are already applying the principles of this new paradigm to environmentally cleaner and more efficient chemical processes, but more progress is required. It is our belief that a new approach to organic synthesis will have to be embraced and that this will not come from small step changes but will require a major adjustment in strategic approach. The aspects of chemical synthesis, physiochemical profiling and bio-evaluation will need to become more closely coupled, whether for pharmaceutical discovery purposes or new material design the arguments are the same. Synthesis procedures cannot operate in isolation to their intended products, such an approach leads to wasted synthesis time and the generation of unwanted material. A more integrated and continuous relay of in-


179

formation regarding the ongoing synthesis and its products in terms of basic characterisation, physical properties and their functions needs to be captured. Immediate collection and analysis of such data will enable more educated and responsive choices to be made, varying from mundane factors such as reaction optimisation to higher-level decisions about what molecules should be synthesised next. The requirements in terms of information retrieval and flexibility of synthetic implementation seem ideally suited to a flow-based approach to chemical synthesis. It is therefore our conclusion that future synthesis programmes will make increasing use of flow techniques and many of these will benefit from the use of solid-supported reagents and scavengers.

References Akelah A, Sherrington DC (1981) Application of functionalized polymers in organic synthesis. Chem Rev 81:557–587 Akelah A, Sherrington DC (1983) Recent developments in the application of functionalized polymers in organic synthesis.Polymer 24:1369–1386 Anderson NG (2001) Practical use of continuous processing in developing and scaling up laboratory processes. Org Proc Res Dev 5:613–621 Arvela RK, Leadbeater NE (2005) Suzuki coupling of aryl chlorides with phenylboronic acid in water, using microwave heating with simultaneous cooling. Org Lett 7:2101–2104 Baumann M, Baxendale IR, Ley SV, Smith CD, Tranmer GK (2006) Fully Automated Continuous Flow Synthesis of 4,5-Disubstituted Oxazoles. Org Lett 9:1521–1524 Baxendale IR, Ley SV (2000) Polymer-supported reagents for multi-step organic synthesis: application to the synthesis of sildenafil. Bioorg Med Chem Lett 10:1983–1986 Baxendale IR, Ley SV (2005a) Synthesis of alkoloid natural products using solid supported reagents and scavengers. Curr Org Chem 9:1521– Baxendale IR, Ley SV (2005b) Synthesis of the alkaloid natural products (+)-plicane and (–)-obliquine, using polymer-supported reagents and scavengers. Ind Eng Chem Res 44:8588–8592 Baxendale IR, Ley SV (2005c) Formation of 4-aminopyrimidines via the trimerization of nitriles using focused microwave heating. J Combinatorial Chem 7:483–489

180


Baxendale IR, Lee A-L, Ley SV (2001) A concise synthesis of the natural product carpanone using solid-supported reagents and scavengers. Synlett 482– 484 Baxendale IR, Ley SV Sneddon H (2002a) A clean conversion of aldehydes to nitriles using a solid-supported hydrazine. Synlett 775–777 Baxendale IR, Lee A-L, Ley SV (2002b) A concise synthesis of carpanone using solid-supported reagents and scavengers. J Chem Soc Perkin Trans 1:1850–1867 Baxendale IR, Ley SV, Nesi M, Piutti C (2002c) Total Synthesis of the amaryllidaceae alkaloid (+)-plicamine and its unnatural enantiomer by using solid-supported reagents and scavengers in a multistepsequence of reactions. Angew Chem Int Ed 41:2194–2197 Baxendale IR, Ley SV, Piutti C, Nesi M (2002d) Total synthesis of the amaryllidaceae alkaloid (+)-plicamine using solid-supported reagents. Tetrahedron 58:6285–6304 Baxendale IR, Ley SV, Ernst M, Krahnert W-R (2002e) Application of polymersupported enzymes and reagents in the synthesis of γ-aminobutyric acid (GABA) analogues. Synlett 1641–1644 Baxendale IR, Brusotti G, Matsuoka M, Ley SV (2002f) Synthesis of nornicotine, nicotine and other functionalised derivatives using solid-supported reagents and scavengers. J Chem Soc Perkin Trans 1 2:143–154 Baxendale IR, Storer RI, Ley SV (2003) Supported reagents and scavengers in multi-step organic synthesis in polymeric materials in organic synthesis and catalysis. Ed Buchmeiser MR VCH, Berlin Baxendale IR, Ley SV, Martinelli M (2005) The rapid preparation of 2-aminosulfonamide-1,3,4-oxadiazoles using polymer-supported reagents and microwave heating. Tetrahedron 61:5323–5349 Baxendale IR, Griffiths-Jones CM, Ley SV, Tranmer GK (2006a) Preparation of the neolignan natural product grossamide by a continuous-flow process. Synlett 427–430 Baxendale IR, Griffiths-Jones CM, Ley SV, Tranmer GK (2006b) Microwaveassisted Suzuki coupling reactions with an encapsulated palladium catalyst for batch and continuous-flow transformations. Chem Eur J 12:4407–4416 Baxendale IR, Deeley J, Griffiths-Jones CM, Ley SV, Saaby S, Tranmer GK (2006c) A flow process for the multi-step synthesis of the alkaloid natural product oxomaritidine: a new paradigm for molecular assembly. J Chem Soc Chem Commun 2566–2568 Baxendale IR, Ley SV, Smith CD, Tranmer GK (2006d) A flow reactor process for the synthesis of peptides utilizing immobilized reagents, scavengers and catch and release protocols. J Chem Soc Chem Commun 4835–4837


181

Bellina F, Carpita A, Rossi R (2004) Palladium catalysts for the Suzuki Crosscoupling reaction: an overview of recent advances. Synthesis 2419–2440 Bhattacharyya SJ (2000) Polymer-supported reagents and catalysts recent advances in synthetic applications. Comb Chem High Throughput Screening 3:65–92 Bhattacharyya SJ (2004) New developments in polymer-supported reagents, scavengers and catalysts for organic synthesis. Curr Opin Drug Discov Devel 7:752–764 Booth RJ, Hodges JC (1997) Polymer-supported quenching reagents for parallel purification. J Am Chem Soc 19:4882–4886 Booth RJ, Hodges JC (1999) Solid-supported reagent strategies for rapid purification of combinatorial synthesis products. Acc Chem Res 32:18–26 Bremeyer N, Ley SV, Ramarao C, Shirley IM, Smith SC (2002) A flow reactor process for the synthesis of peptides utilizing immobilized reagents, scavengers and catch and release protocols. Synlett 1843–1844 Caldarelli M, Habermann J, Ley SV (1999a) Clean five-step synthesis of an array of 1,2,3,4-tetra-substituted pyrroles using polymer-supported reagents. J Chem Soc., Perkin Trans 1 107–110 Caldarelli M, Habermann J, Ley SV (1999b) Synthesis of an array of potential matrix metalloproteinase inhibitors using a sequence of polymer-supported reagents. Biorg Med Chem Lett 9:2049–2052 Caldarelli M, Baxendale IR, Ley SV (2000) Clean and efficient synthesis of azo dyes using polymer-supported reagents. J Green Chem 43–45 Chakrabarti A, Sharma MM (1993) Cationic ion exchange resins as catalyst. React Polym 20:1–45 Dye JL, Lok MT, Tehan FJ, Creaso JM, Voorhees KJ (1973) Flow synthesis. Substitute for the high-dilution steps in cryptate synthesis. J Org Chem 38:1773–1775 Drewry DH, Coe DM, Poon S (1999) Solid-supported reagents in organic synthesis. Med Res Rev 19:97–148 Doku GN, Verboom W, Reinhoudt DN, van den Berg A (2005) On-microchip multiphase chemistry—a review of microreactor design principles and reagent contacting modes. Tetrahedron 61:2733–2742 Ehrfeld W, Hessel V, Löwe H (2000) Microreactors: new technology for modern chemistry. Wiley-VCH, Weinheim, Germany Fletcher PDI, Haswell SJ, Pombo-Villar E, Warrington BH, Watts P, Wong SYF, Zhang X (2002) Micro reactors: principles and applications in organic synthesis. Tetrahedron 58:4735–4757 Haberman. Chem Eur J 8:4115–4119

182


Haswell SJ, Middleton RJ, O’Sullivan B, Skelton V, Watts P, Styring PJ (2001) The application of micro reactors to synthetic chemistry. Chem Soc Chem Commun 5:391–398 Hinzen B, Ley SV (1998) Synthesis of isoxazolidines using polymer supported perruthenate (PSP). J Chem Soc Perkin Trans 11–2 Hodges JC (1999) Covalent scavengers for primary and secondary amines. Synlett 1:152–158 Humphrey CE, Easson MAM, Tierney JP, Turner N (2003) Capture and release reagent for the synthesis of amides and novel scavenger resin. J Org Lett 5:849–852 Jamieson C, Congreave MS, Emiabata-Smith DF, Ley SV (2000) A rapid approach for the optimisation of polymer supported reagents in synthesis. Synlett 603–607 Jamieson C, Congreave MS, Emiabata-Smith DF, Ley SV, Scicinski J (2002) application of ReactArray robotics and design of experiments techniques in optimisation of supported reagent chemistry. J Org Proc Res Dev 6:823– 825 Jas G, Kirschning A (2003) Continuous flow techniques in organic synthesis. Chem Eur J 9:5708–5723 Jönsson D, Warrington BH, Ladlow M (2004) Automated flow-through synthesis of heterocyclic thioethers. J Comb Chem 6:584–595 Kabza KG, Chapados BR, Gestwicki JE, McGrath JL (2000) Microwaveinduced esterification using heterogeneous acid catalyst in a low dielectric constant medium. J Org Chem 65:1210–1214 Kaldor SW, Siegel MG, Dressman BA, Hahn PJ (1996) Use of solid supported nucleophiles and electrophiles for the purification of non-peptide small molecule libraries. Tetrahedron Lett 37:7193–7196 Kappe CO (2004) Controlled microwave heating in modern organic synthesis. Angew Chem Int Ed 43:6250–6284 Karnatz FA, Whitmore FC (1932) Dehydration of diethylcarbinol. J Am Chem Soc 54:3461 Kirschning A, Jas G (2004) Applications of immobilized catalysts in continuous flow processes. Topics in Curr Chem 209–239 Kirschning A, Monenschein H, Wittenberg R (2001) Functionalized polymers – emerging versatile tools for solution-phase chemistry and automated parallel synthesis. Angew Chem Int Ed 40:650–679 Kotha S, Lahiri S, Kashinath D (2002) Recent applications of the Suzuki– Miyaura cross-coupling reaction in organic synthesis. Tetrahedron 58:9633–9695


183

Leadbeater NE, Pillsbury SJ, Shanahan E, Williams VA (2005) An assessment of the technique of simultaneous cooling in conjunction with microwave heating for organic synthesis. Tetrahedron 61:3565–3585 Lee CKY, Holmes AB, Ley SV, McConvey IF, Al-Duri B, Leeke GA, Santos RCD, Seville JPK (2005) Efficient batch and continuous flow Suzuki crosscoupling reactions under mild conditions, catalysed by polyurea-encapsulated palladium (II) acetate and tetra-n-butylammonium salts. J Chem Soc Chem Commun 2175–2177 Ley SV, Baxendale IR (2002a) Organic synthesis in a changing world. Chem Rec 2:377–388 Ley SV, Baxendale IR (2002b) New tools and concepts for modern organic synthesis. Nat Rev Drug Disc 1:573–586 Ley SV, Massi A (2000) J Comb Chem Polymer supported reagents in synthesis: preparation of bicyclo[2.2.2]octane derivatives via tandem michael addition reactions and subsequent combinatorial decoration. 2:104–107 Ley SV, Schucht O, Thomas AW, Murray PJ (1999) Synthesis of the alkaloids (±)-oxomaritidine and (±)-epimaritidine using an orchestrated multi-step sequence of polymer supported reagents. J Chem Soc Perkin Trans 1 1251– 1252 Ley SV, Baxendale IR, Bream RN, Jackson PS, Leach AG, Longbottom DA, Nesi M, Scott JS, Storer RI, Taylor SJ (2000) Multi-step organic synthesis using solid-supported reagents and scavengers: a new paradigm in chemical library generation. J Chem SocP erkin Trans 1 3815–4195 Ley SV, Takemoto T, Yasuda K (2001) Solid-supported reagents for the oxidation of aldehydes to carboxylic acids. Synlett 1555–1556 Ley SV, Lumeras L, Nesi M, Baxendale IR (2002a) Synthesis of trifluoromethyl ketones using polymer-supported reagents. Comb Chem High Throughput Screening 5:195–199 Ley SV, Baxendale IR, Brusotti G, Caldarelli M, Massi A (2002b) Solid-supported reagents for multi-step organic synthesis: preparation and application. Farmaco 57:321–330 Ley SV, Ramarao C, Gordon RS, Holmes AB, Morrison AJ, McConvey IF, Shirley IM, Smith SC, Smith MD (2002c) Polyurea-encapsulated palladium(II) acetate: a robust and recyclable catalyst for use in conventional and supercritical media. J Chem Soc Chem Commun 1134–1136 Ley SV, Baxendale IR, Myers RM (2005) Polymer-supported regents scavengers and catch-and-release techniques for chemical synthesis. In: Taylor J, Triggle D (eds) Comprehensive medicinal chemistry II, Vol. 3, Drug Discovery Technologies. Elsevier, Oxford, pp 79–836

184


Ley SV, Baxendale IR, Myers RM (2006) The use of polymer supported reagents and scavengers in the synthesis of natural products. In: Boldi AM (ed) Combinatorial synthesis of natural product-based libraries. CRC Press Boca-Raton, pp 131–163 Luckarift HR, Nadeau LJ, Spain JC (2005) Continuous synthesis of aminophenols from nitroaromatic compounds by combination of metal and biocatalyst. J Chem Soc Chem Commun 383–384 Miura M (2004) Rational ligand design in constructing efficient catalyst systems for suzuki-miyaura coupling. Angew Chem Int Ed 43:2201–2203 Nüchter M, Ondruschka B, Bonrath W, Gum A (2004) Microwave-assisted synthesis – a critical technology overview. Green Chem 6:128–141 Parlow JJ, Devraj RV, South MS (1999) Solution-phase chemical library synthesis using polymer-assisted purification techniques. Curr Opin Chem Biol 3:320–336 Pershichini PJ (2003) Carbon-Carbon Bond Formation via Boron Mediated Transfer. Curr Org Chem 7:1725–1736 Ramarao C, Ley SV, Smith SC, Shirley IM, DeAlmeida NJ (2002) Encapsulation of palladium in polyurea microcapsules. Chem Soc Chem Commun 1132–1133 Saaby S, Baxendale IR, Ley SV (2005) Non-metal-catalysed intramolecular alkyne cyclotrimerization reactions promoted by focused microwave heating in batch and flow modes. Org Biomol Chem 3:3365–3368 Sands M, Haswell SJ, Kelly SM, Skelton V, Morgan DO, Styring P, Warrington B (2001) The investigation of an equilibrium dependent reaction for the formation of enamines in a microchemical system. Lab Chip 1:64–65 Schwartz MA, Holton RA (1970) Intramolecular oxidative phenol coupling. II. Biogenetic-type synthesis of (+-)-maritidine. J Am Chem Soc 92:1090– 1092 Sherrington DC (2001) Polymer-supported reagents, catalysts, and sorbents: evolution and exploitation – a personalized view. J Polym Sci Pol Chem 39:2364–2377 Shuttleworth SJ, Allin SM, Sharma PK (1997) Functionalised polymers: recent developments and new applications in synthetic organic chemistry. Synthesis 1217–1239 Shuttleworth SJ, Allin SM, Wilson RD, Nasturica D (2000) Functionalised polymers in organic chemistry: part 2. Synthesis 8:1035–1074 Siu J, Baxendale IR, Ley SV (2004) Microwave assisted Leimgruber–Batcho reaction for the preparation of indoles, azaindoles and pyrroylquinolines. Org Biomol Chem 160


185

Storer RI, Takemoto T, Jackson PS, Ley SV (2003) A total synthesis of epothilones using solid-supported reagents and scavengers. Angew Chem Int Ed 42:2521–2525 Storer RI, Takemoto T, Jackson PS, Brown DS, Baxendale IR, Ley SV (2004) Multi-step application of immobilized reagents and scavengers: a total synthesis of epothilone C. Chem Eur J 10:2529–2547 Sussman S (1946) Ind Eng Chem 38:1228 Thomas JR, Faucher FJ (2000) Thermal modeling of microwave heated packed and fluidized bed catalytic reactors. Microw Power Electromagn Energy 35:165–174 Thompson LA (2000) Recent applications of polymer-supported reagents and scavengers in combinatorial, parallel, or multistep synthesis. Curr Opio Chem 4:324–337 Toteja RSD, Jangida BL, Sundaresan M, Venkataramani B (1997) Water sorption isotherms and cation hydration in dowex 50w and amberlyst-15 ion exchange resins. Langmuir 13:2980–2982 Vickerstaff E, Warrington BH, Ladlow M, Ley SV (2004) Fully automated polymer-assisted synthesis of 1,5-biaryl pyrazoles. J Comb Chem 6:332– 339 Wathey B, Tierney JP, Lidstrom P, Westman J (2001) Microwave-assisted organic synthesis—a review. Tetrahedron 57:9225–9283 Wathey B, Tierney JP, Lidstrom P, Westman J (2002) The impact of microwaveassisted organic chemistry on drug discovery. Drug Discovery Today 7:373– 380 Watts P, Haswell SJ (2003a) Microfluidic combinatorial chemistry. Curr Opin Chem Biol 7:380–387 Watts P, Haswell SJ (2003b) Continuous flow reactors for drug discovery. Drug Discov Today 8:586–593 Wison NS, Sarko CR, Roth GP (2004) Development and applications of a practical continuous flow microwave Cell. Org Proc Res Dev 8:535–538 Yu J-Q, Wu H-C, Ramarao C, Spencer JB, Ley SV 2003) Transfer hydrogenation using recyclable polyurea-encapsulated palladium: efficient and chemoselective reduction of aryl ketones. J Chem Soc Chem Commun 678– 679 Zu ZP, Chuang KT (1996) Kinetics of acetic acid esterification over ion exchange catalysts. Can J Chem Eng 74:493–500


Solid-Phase Supported Synthesis: A Possibility for Rapid Scale-Up of Chemical Reactions M. Meisenbach(u) , T. Allmendinger, C.-P. Mak Chemical and Analytical Development, Novartis Pharma AG, 4002 Basel, Switzerland email: [email protected]

1 Introduction . . . . . . 2 Results and Discussion 3 Conclusion . . . . . . . References . . . . . . . . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

187 188 201 202

Abstract. The direct scale-up of a solid-phase synthesis has been demonstrated with 4-(2-amino-6-phenylpyrimidin-4-yl)benzamide and an arylsulfonamidosubstituted hydroxamic acid derivative as examples. These compounds were obtained through combinatorial chemistry and solution-phase synthesis was used in parallel to provide a comparison. By applying highly loaded polystyrenederived resins as the solid support, a good ratio between the product and the starting resin is achieved. We have demonstrated that the synthesis can be scaled up directly on the solid support, successfully providing the desired compounds easily and quickly in sufficient quantities for early development demands.

1

Introduction

Solid-phase synthesis for small organic compounds is widely used in research and academia for rapid lead finding and lead optimisation. The

188

M. Meisenbach, T. Allmendinger, C.-P. Mak

number of hits obtained from combinatorial methods is expected to increase in the future and consequently numerous compounds as potential drug candidates will enter into development. Process chemists are then faced with the problem of rapidly delivering the first amounts necessary for early preclinical and clinical studies. If the compounds were obtained by a solid-phase approach, solution-phase procedures for their synthesis might not be readily available. To tackle this problem, we were interested in gaining experience in the direct scale-up of solidphase syntheses without investing resources searching for a solutionphase alternative. An added advantage in this approach is inherent: the potential time savings since multi-step procedures could be conducted without isolation and purification of intermediates. Our group had previously reported on this topic (Meisenbach et al. 2003) and very few examples are found in the literature (Raillard et al. 1999; Prühs et al. 2006). Herein we will expand upon our earlier work with additional examples. With the following examples, we will investigate and discuss the following: (a) Scale-up phenomena of different solid phase reactions and the corresponding on-bead analytics; (b) the effect of loading (an equivalent to concentration in solution-phase chemistry); (c) comparison with the solution-phase alternative and (d) the synthesis and use of new trityl linkers.

2

Results and Discussion

The first example describes the synthesis of a pyrimidine derivative. Starting from α,β-unsaturated ketones (see Schemes 1, 8), a library of different heterocycles was prepared in research (Felder and Marzinzik 1998). In preparation for any large-scale synthesis, the availability of starting materials is always considered (Lee and Robinson 1995). For this work, we had to replace Rink amide resin B (Rink 1987), which was used by our colleagues in research for the synthesis of pyrimidine 1 due to its unavailability in large quantities (see Fig. 1). It was replaced with the Rink amide acetamido resin 4, which is well established in peptide amide synthesis (Bernatowicz et al. 1989) and easily accessible.

SPSS: Rapid Scale-Up

189

Fig. 1. Structural comparison of the Rink-linker compared to the linker used for the scale-up

Thus (see Scheme 1), 1.5 equiv. of the acetic acid derivative 3 was coupled to aminomethyl polystyrene (AMPS 2a, 1.54 mmol/g) by standard amide-forming conditions. After complete acylation as indicated by a negative Kaiser-test (Kaiser et al 1970) for unreacted amino functions, resin 4a was checked for its loading using well-elaborated UVtechniques (Meienhofer et al. 1979). After cleaving the Fmoc group with 20% diethylamine in DMF, 4-carboxybenzaldehyde 5 was coupled (diisopropyl carbodiimide DIC, HOBt). Increasing the reaction time allowed the reduction of the amount of building block 5 by a factor of 10 as compared to the original protocol. The structure of the resulting solid-phase-supported aldehyde 6a was confirmed by IR spectroscopy (Yan et al. 1999), which showed a strong C=O band at 1,710 cm–1 and the characteristic C–H band at 2,730 cm–1 . The subsequent Claisen-Schmidt reaction was originally performed on a 10-µmol scale using 20-fold excess of both acetophenone and LiOH to achieve complete formation of the chalcone 8. This result could be verified on a small scale; however, employing the same conditions on a 35-mmol scale resulted in no conversion even after 22 h, as revealed by IR spectroscopy. By cleaving a resin sample with 20% TFA in dichloromethane, only p-formylbenzamide 11 was detected by HPLC. This result may be explained by the low solubility of LiOH in DME under dry/aprotic conditions. Therefore, a small amount of EtOH was added, which initiated a fast reaction (Chiu et al. 1999) and the formation of the desired chalcone 8 together with 20% of the Michael adduct 10 (Fig. 2). This was confirmed by sample cleavage from the resin and LC-MS analysis. Short reaction screening resulted in considerable im-

190


Fig. 2. Structure of the Michael-adduct

provements: using less acetophenone 7 and LiOH (1.5 and 0.5 equivalents, respectively) and a mixed solvent system of THF and methanol gave complete conversion within only 1 h, forming only 5% of Michael adduct as by-product. To get more insight into what exactly was going on, online Raman spectroscopy was used to monitor the conversion of this Claisen-Schmidt reaction (Dyson et al. 2000) (Fig. 3). The measurements indicate that the optimum reaction time is 50 min before the signal at 1,608 cm–1 starts to decrease, which is when the product starts to be consumed because of the Michael addition (see Fig. 3). The final conditions were scaled up with no problems: chalcone 8a and guanidine (liberated from its hydrochloride with sodium ethoxide) were heated in dimethyl acetamide while bubbling air through the mixture to form pyrimidine 9a. After complete conversion (16 h), the product was cleaved from the support (20% trifluoroacetic acid in DCM). Pure 4-(2-amino-6-phenyl-pyrimidin-4-yl)benzamide 1 was obtained as its trifluoroacetate salt upon evaporation of the filtrate and recrystallisation of the residue from ethanol/water in 56% overall yield based on the solid phase attached 4-carboxybenzaldehyde 6a. After isolating the product of a solid phase synthesis, the support (resin + linker) is usually discarded as waste, although successful examples of its reuse in further synthetic cycles are known with trityl type linkers (Frechet and Haque 1975). To reduce both volume of operation and amount of waste, the loading of the resin (quantified as millimoles of functionality per gram) has to be increased. Besides theoretical limitations (for polystyrene this is reached when every phenyl ring is substituted by the linker), there may be practical boundaries for using highly loaded resins in solid-phase supported synthesis. This issue was studied


191

Fig. 3. a Raman spectra (preprocessed); this peak predominantly shows formation of product. b Spectral changes over time shown for the wave number of maximum signal (1608 cm–1 )

in detail with the preparation of 1, where the resin loading was varied. This was also another reason to switch from the ether-bonded Rinklinker B to the acetic acid derivative 4, which can be assembled from 3 and differently loaded aminomethylated polystyrene resins (AMPS, 2). AMPS is commercially available with loading up to 2.9 mmol/g 2b (NovaBiochem, Switzerland). By adapting and optimising the proce-

192


dure developed by Adams (Adams et al. 1998), higher loaded resins were prepared. Thus polystyrene cross-linked with 1% divinylbenzene was reacted with N-chloromethyl phthalimide 12 in dichloromethane using iron (III) chloride as Friedel-Crafts catalyst. If the reaction is performed at 25°C a colourless product 13 is obtained (Scheme 3), in con-

Scheme 1. SPSS of the pyrimidine derivative


193

Scheme 2. Synthesis scheme of the AMPS

trast to dark yellow resins obtained when working under reflux. The phthaloyl protective group was removed by means of aminolysis using methylamine in water/THF in order to avoid the common but toxic hydrazine and dioxane. The desired loading can be obtained by adjusting the ratio of PS, chloromethyl phthalimide and FeCl3 . We synthesised AMPS with up to 4.48 mmol/g (2c) corresponding to two out of three phenyl rings being aminomethylated. We have not extended the investigation to the highest possible loading of AMPS. A resin with up to 7.3 mmol/g (96% of phenyl-rings on polystyrene are substituted) has been described previously (Zikos and Ferderigos 1995), but its application has not been reported so far. To study the effect of loading, the synthesis depicted in Scheme 1 was repeated using different resin loadings. The conditions during reactions on higher loaded resins (2b and 2c) as compared to the initially used 2a did not need any adjustments. The quality of the product was comparable and the ratio of product to solid support was increased (Table 1). Without the experience and the equipment to perform solid-phase supported syntheses on a larger scale, chemists explore alternative routes utilising solution-phase chemistry. To compare the direct scale-up on solid support and to evaluate the advantages and disadvantages of both approaches, pyrimidine 1 was prepared in solution phase as well. For this relatively small and simple molecule, similar chemistry was applied (see Scheme 3) with some interesting results arising. Heating 4-carboxybenzaldehyde 5 in excess thionyl chloride, which is described to form acid chloride 14 (Graffner-Nordberg et al. 1998),


194

Scheme 3. Synthesis of the pyrimidine derivative in liquid phase Table 1 Solid phase synthesis of pyrimidine 1-TFA salt starting with resins of different loading Loading of AMPS, scale of synthesis

Mass of 9 (g)

Yield of crude Purity TFA salt (area %)∗

in (g) in (%) 2a, 1.54 mmol/g 49 40 mmol, 26 g 2b, 2.86 mmol/g 61.39 70 mmol, 24.5 g 2c, 4.48 mmol/g 74.9 100 mmol, 22.3 g ∗

RP-HPLC

Overall yield and purity after recrystallisation of 1-TFA salt in (%) in (area %)∗

14.9

92

84

56

>98

17.8

66

80

47

>97

31.8

82

86

55

>98


195

Table 2 Comparison of the liquid and solid phase synthesis of the pyrimidine derivative 1

Liquid phase Solid phase

Yield

# of steps

Time of manufacturing

39% 73%

4 4 + cleavage + crystallisation

3d 3d

actually afforded the trichloro-compound 15 instead. Therefore the milder Vilsmeier reagent was used, followed by aminolysis in order to obtain 11. Due to its solubility in water, variable yields of 11 were obtained depending on the workup procedure employed. The Aldol condensation with acetophenone under standard conditions gave chalcone 17 containing 10% of the intermediate 16. Its structure was revealed by independent synthesis (Ohki et al. 1988), to compare the NMR-data and chromatographic properties. Hydroxyketone 16 turned out to be hardly soluble (even in dimethyl sulfoxide), and precipitated with 17. These phenomena indicate the advantage of solid-phase supported synthesis when intermediates are involved, possessing either very low solubility in organic solvents (like 16) or high aqueous solubility (like 11). Finally the condensation with guanidine and the following oxidation afforded pyrimidine 1 in moderate yield. The results are compared in Table 2. As second example for the scale-up of solid-phase reactions directly on solid support, we chose an arylsulfonamido-substituted hydroxamic acid derivative stemming from the matrix metalloproteinase inhibitor library (MMP) of our research colleagues (Breitenstein et al. 2001). In this case, there was already a solution-phase synthesis available for comparison (see Scheme 4). The synthesis starts with the imine formation of a benzaldehyde 18 with the glycine methyl ester, which is then reduced to the benzylamine 20 using sodium borohydride in methanol/ THF (2:1). The sulfonamide formation is carried out in dioxane/H20 (2:1) with triethylamine as the base and after neutralisation and evaporation the product 21 can be crystallised from tert. butylmethyl ether. After deprotection with LiOH, the acid is activated by treatment with oxalyl chloride and finally converted into the hyroxamic acid 23 in 33.7% yield overall. The SPSS following this route is illustrated in Scheme 5. In the first step, Fmoc-protected glycine is attached to a trityl-derived hydroxyl

196


Scheme 4. Synthesis of a MMP inhibitor, a hydroxamic acid derivative in liquid phase

amine resin using DIC and HOBt. A sterically demanding linker was selected because of the reactivity of the hydroxamic acid’s nitrogen. After the cleavage of the Fmoc group, the polymer bounded benzylamine 26 is synthesised via reductive amination (see also Table 3). The sulfonamide formation is performed in DCM using N-methylmorpholine as base, followed by the final cleavage of the product from the resins using TFA in different concentrations in DCM depending on the linker used. At first glance, the synthesis of 23 seems to be straightforward. However, some difficulties were encountered, which are described below. a. The monitoring of the imine formation c and reduction d by simple cleavage and HPLC-analysis is impossible due to instability of the intermediates under acidic conditions. IR-monitoring (C=X-bands) was ineffective because a CO-N-functionality is always present (Table 3, no. 1). b. 23 Itself turned out to be labile towards the harsher cleavage conditions during sample evaporation (Table 3, no. 2a). Only a small scale run with linker 24a was successful when the solution after cleavage was immediately neutralized; otherwise debenzylation occurred forming 28 (Table 3, no. 2b).


197

Scheme 5. SPS synthesis of the hydroxamic acid derivative via reductive amination a Reduction, b Cl-SO2 -Ph-R2, NMM, DCM 3–4 h c 10% or 1–2% TFA in DCM with direct neutralisation with sat. NaHCO3 , d without neutralisation

c. Analogous to the solution-phase results (Harmon et al. 1970), imines from glycine hydroxamic acids (like 19) may form imidazolinones; these would not be reduced but sulfonylated in the following step forming 29 (Scheme 6). Indeed, the outcome of the whole sequence turned out to be highly dependent on the conditions of the reduction step a. We tried to substitute the highly toxic sodium cyanoborohydride by NaBH(OAc)3 or NaBH4 , but this was unsuccessful (Table 3, nos. 4, 5). Only when using NaCNBH3 in a mixture of dichloromethane, trimethyl orthoformate containing 1% acetic acid was the desired 23 obtained. Without acetic acid (which we wanted to avoid in combination with NaCNBH3 ) or using different solvents (DMF or THF), the reduction was not successful and 29 was isolated (Table 3, nos. 3, 6).

198


Scheme 6. Synthesis scheme for the preparation of the 4-benzyloxy-trityl hydroxylamine

For these reasons, an alternative route and more acid labile linkers compared to p-carboxy trityl linker 24a initially used were sought, to avoid high concentrations of TFA for the final cleavage. The synthesis of the alkoxysubstitued linkers 24b (Meisenbach and Voelter 1997) and 24c, which can be synthesised directly on the solid support in five steps, offer the possibility of linkers with tailor-made stability. In the case of the benzyloxytrityl-hydroxylamine resin 24b, the starting material is the Merrifield resin, chloromethylated polystyrene (1.7 mmol Cl × g–1 ) which is treated with 3 equiv. of 4-hydroxy-methyl benzoate in DMA with sodium methylate as base. The Beilstein test is used for monitoring and microanalyses showed the absence of chloride (Scheme 6). Resin 24c is a far cheaper alternative also allowing a facile variation of its loading (Scheme 7). Starting with inexpensive 1% crosslinked polystyrene, a versatile linker was prepared following the protocol of Fréchet (Fréchet and Nuyens 1976). The Friedel-Crafts benzoylation is carried out using DCM instead of highly toxic and highly inflammable carbon disulfide at 5°C with 0.66 equiv. AlCl3 and 0.6 equiv. benzoylchloride affording a resin where two-thirds of the phenyl rings are functionalised. The trityl system is then generated by a Grignard reaction with 10 equiv. of the corresponding bromo compounds and 10 equiv. magnesium in THF refluxing for 24 h. The structures were confirmed by the disappearance of the CO band in the IR spectrum at 1,710 cm–1 and the appearance of a strong OH band at 3,500 cm–1 , indi-

1. Imine formation 2. Reduction




3

4

5

6

2b


2a

24b

24a

24a

24b

24a

24a

Red. alkylation

1

TMOF/DCM 1% HAc 1. TMOF/DCM 2. TMOF/DCM, 1% HOAc

Solvent 2% 48% 28% 28

20% TFA/DCM

Comp. 23 HPLC [A%]

20% TFA/DCM

Cleavage conditions

10% TFA/DCM with direct 80% neutralisation into NaHCO3 Sol. 1% TFA/DCM with direct 79% 29 NaCNBH3 1. TMOF/DCM 2. TMOF/DCM neutral. into NaHCO3 solution 10% TFA/DCM with direct 40% NaBH(OAc)3 1. TMOF/DCM 2.1% HOAc in DMF neutralisation into NaHCO3 solution 1. TMOF/DCM 10% TFA/DCM with direct 54% NaBH3 2. THF/MeOH (3:1) neutralisation into NaHCO3 solution 1% TFA/DCM with direct 80% 29 NaCNBH3 1. TMOF/DCM 2. 1% HOAc in DMF neutralisation into NaHCO3 solution

NaCNBH3

NaCNBH3

Linker Red. agent

No. of Reaction Exp.

Table 3 Solid phase synthesis of 23 via reductive amination

SPSS: Rapid Scale-Up 199

200


Scheme 7. Synthesis scheme for the preparatin of the 4-methoxy-trityl hydroxylamine linker

Scheme 8. New route for the SPSS of hydroxamic acid derivative by nucleophilic substitution

cating that the reaction had gone to completion. The OH-functionalized resins were transformed into the orange halide when reacted with AcCl in toluene at 70°C for 1 h. Finally, upon treatment with 3 eq. of N-hydroxyphthalimide and Hünig’s base in dichlormethane, the chloro-


201

Table 4 Solid phase synthesis of 23 PS

24c resin

292 g 556 g,

Scale of synthesis and mass of starting resin 24c

Scale of synthesis and mass of starting resin 38

Crude 23 after 23 after cleavage with crystallisation 2%TFA/DCM from EtOAc/heptane Yield based on 38, purity HPLC

201.5 g/ 345 mmol

235 g/ 0.93 mmol/g, 220 mmol 315 g/ 0.74 mmol/g, 233 mmol

75.26 g, 77.2%, 42.4 g, 43.5%, 86.3A% 99A%

1.71 268 g/ mmol/g 458 mmol

83.08 g, 80.5%, 54.5 g, 52%, 87.1A% 99.1A%

resins are converted to 33 and 37, respectively. The cleavage of phthaloyl protective group was carried out as described above for the AMPS resins and can be easily monitored by the disappearance of the CO band in the IR spectrum at 1,710 cm–1 . With these solid supports in hand, we turned our attention to a new route to the synthesis of our target molecule 23 (Scheme 8). The tricky reductive amination should be replaced by an N-alkylation. To that end, bromoacetic acid is attached to 24c using DIC and Hünig’s base followed by the nucleophilic substitution with the corresponding benzylamine in DMSO/toluene (1:1), which can be easily monitored by the Beilstein test, followed by sulfonamide formation in DCM using Nmethylmorpholine as base. For the final cleavage, 2% TFA in DCM is used and the resulting solution is filtered in a saturated NaHCO3 solution to neutralise the acid before evaporation of the solvent. The crude product was then crystallised from ethyl acetate/heptane to yield the desired product in 27% yield overall and 99A% HPLC purity (see Table 4).

3

Conclusion

In summary, we demonstrated the possibility of the fast scale-up of solid-phase supported synthesis. In one case (pyrimidine derivate), the research protocols could be used directly with only minor modifica-

202


tions. In another case, an alternative synthesis was needed for a successful and efficient scale-up. For these examples with only a few reaction steps, the production time on solid support is comparable with a synthesis in solution but the overall yield (47%–56%) exceeds that obtained by solution phase synthesis (21%–34%). A further achievement is the accessibility of highly loaded AMPS and trityl resins to increase the product/resin ratio and the volume productivity. Combining these factors, the competitive position of a fast up-scale of given SPSS-protocols compared to the time-consuming development of a new solution phase synthesis for small compounds is considerably improved, in particular when the time savings is considered, one of the most important factors in the early stage of drug development.

References Adams JH, Cook RM, Hudson D, Jammalamadaka V, Lyttle MH, Songster MF (1998) A reinvestigation of the preparation, properties, and applications of aminomethyl and 4-methylbenzhydrylamine polystyrene resins. J Org Chem 63:3706–3716 Bernatowicz MS, Daniels SB, Köster H (1989) A comparison of acid-labile linkage agents for the synthesis of peptide C-terminal amides. Tetrahedron Lett 30:4645–4648 Breitenstein W, Hayakawa K, Iwasaki G, Kanazawa T, Kasaoka T, Koizumi S, Matsunaga S, Nakajima M, Sakaki J (2001) Preparation of arylsulfonamidosubstituted hydroxamic acid derivatives as MMP2 inhibitors. Int Pat Appl WO 2001010827 Chiu C, Tang Z, Ellingboe JW (1999) Solid-phase synthesis of 2,4,6-trisubstituted pyridines. J Comb Chem 1:73–77 Dyson RM, Helg AG, Meisenbach M, Allmendinger T (2000) In situ observation of the progress of a large-scale on-bead reaction. 11th International Symposium on Pharmaceutical and Biomedical Analysis, Basle, Switzerland, p 007 Felder ER, Marzinzik AL (1998) Key intermediates in combinatorial chemistry: access to various heterocycles from α,β-unsaturated ketones on solid phase. J Org Chem 63:723–727 Fréchet JMJ, Haque KE (1975) Use of polymers as protecting groups in organic synthesis. II. Protection of primary alcohol functional groups. Tetrahedron Lett 16:3055–3056


203

Fréchet JMJ, Nuyens LJ (1976) Use of polymers as protecting groups in organic synthesis. III. Selective functionalisation of polyhydroxy alcohols. Can J Chem 54:926–934 Graffner-Nordberg M, Sjödin K, Tunek A, Hallberg A (1998) Synthesis and enzymatic hydrolysis of esters, constituting simple models of soft drugs. Chem Pharm Bull 46:591–601 Harmon RE, Rizzo VL, Gupta SK (1970) Synthesis of 3-hydroxy-4-imidazolidinones. J Heterocyc Chem 7:439–442 Kaiser E, Colescott RL, Bossinger CD, Cook PI (1970) Color test for detection of free terminal amino groups in the solid-phase synthesis of peptides. Anal Biochem 34:595–598 Lee S, Robinson G (1995) Process development: fine chemicals from grams to kilograms. Oxford University Press, Oxford Meienhofer J, Waki M, Heimer EP, Lambros TJ, Makofske RC, Chang CD (1979) Solid phase synthesis without repetitive acidolysis. Preparation of leucyl-alanyl-glycyl-valine using 9-fluorenylmethyloxycarbonylamino acids. Int J Pep Prot Res 13:35–42 Meisenbach M, Voelter W (1997) New methoxy-substituted tritylamine linkers for the solid phase synthesis of protected peptide amides. Chem Lett 1265– 1266 Meisenbach M, Allmendinger T, Mak CP (2003) Scale-up of the synthesis of a pyrimidine derivative directly on solid support. Org Proc Res Dev 7:553– 558 Ohki H, Wada M, Akiba K (1988) Bismuth trichloride as a new efficient catalyst in the aldol reaction. Tetrahedron Lett 29:4719–4720 Prühs S, Dinter C, Blume T, Schütz A, Harre M, Neh H (2006) Upscaling the solid-phase synthesis of a tetrahydrocarbazole in chemical development. Org Proc Res Dev 10:441–445 Raillard SP, Ji G, Mann AD, Baer TA (1999) Fast scale-up using solid-phase chemistry. Org Proc Res Dev 3:177–183 Rink H (1987) Solid phase synthesis of protected peptide fragments using a trialkoxydiphenyl-methylester resin. Tetrahedron Lett 28:3787–3790 Yan B, Gremlich HU, Moss S, Coppola GM, Sun Q, Liu LJ (1999) Comparison of various FTIR and FT Raman methods: applications in the reaction optimisation stage of combinatorial chemistry. J Comb Chem 1:46–54 Zikos CC, Ferderigos NG (1995) Preparation of high capacity aminomethylpolystyrene resin. Tetrahedron Lett 36:3741–3744


Microstructured Reactors for Development and Production in Pharmaceutical and Fine Chemistry V. Hessel(u) , P. Löb, U. Krtschil, H. Löwe Department of Chemical Engineering and Chemistry, Eindhoven University of Technology, STW 1.35, PO Box 513, 5600 MB Eindhoven, The Netherlands email: [email protected]

1 2 3

Microreactors . . . . . . . . . . . . . . . . . . . . . . . . . Microreactor Processes and Plants . . . . . . . . . . . . . . Cost Analysis for General Judgment of Microreactor Competitiveness . . . . . . . . . . . . . . . 3.1 Case of Low Plant Costs: Kolbe-Schmitt Synthesis . . . . . . 3.2 The Case of High Plant Costs, Hypothetical Reaction . . . . 4 New Process Windows: Speed up Microreactor Chemistry . . 5 Some Thoughts on Scale-out of MicroprocessTechnology . . 5.1 Liquid–Liquid Dispersion for Suzuki Coupling: A Redispersion Reactor . . . . . . . . . . . . . . . . . . . . 5.2 Solvent-Free Ionic Liquid Synthesis with Large Heat Release: Capillary or Integrated Reactors . . 5.3 Gas–Liquid Processing Scale-out: Falling Film Microreactor 6 Industrial Production Cases . . . . . . . . . . . . . . . . . . 6.1 Nitroglycerine Production Plant . . . . . . . . . . . . . . . . 6.2 Radical Polymerization Plant . . . . . . . . . . . . . . . . . 6.3 Grignard Exchange Reaction Plant . . . . . . . . . . . . . . 6.4 Swern-Moffat Oxidation Plant . . . . . . . . . . . . . . . . 6.5 Yellow Nano-Pigment Plant . . . . . . . . . . . . . . . . . . 6.6 Polymer Intermediate Plant . . . . . . . . . . . . . . . . . . 7 Conclusions and Outlook . . . . . . . . . . . . . . . . . . . References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . 206 . . . 208 . . . . .

. . . . .

. . . . .

209 209 212 216 221

. . . 222 . . . . . . . . . . .

. . . . . . . . . . .

. . . . . . . . . . .

223 225 229 229 230 231 231 233 234 235 237

V. Hessel et al.

206

Abstract. The true potential of microprocess technology for process intensification is not yet fully clear and needs to be actively explored, although more and more industrial case stories provide information. This paper uses a shortcut cost analysis to show the major cost portions for processes conducted by microstructured reactors. This leads to predicting novel chemical protocol conditions, which are tailored for microprocess technology and which are expected to highly intensify chemical processes. Some generic rules to approach this are termed new process windows, because they constitute a new approach to enabling chemistry. Using such process intensification together with scaled-out microstructured reactors, which is demonstrated by the example of gas–liquid microprocessing, paves the road to viable industrial microflow processes. Several such commercially oriented case studies are given. Without the use of new process windows conditions, microprocess technology will probably stick to niche applications.

1

Microreactors

Microreactors are reactors made by microfabrication that typically contain microchannels as flow-through elements for continuous processing (Hessel et al. 2004a, 2005; Ehrfeld et al. 2000; Jensen 1999, 2001; Fletcher et al. 2002; Haswell and Watts 2003; Gavriilidis et al. 2002; Jähnisch et al. 2004; Kolb and Hessel 2004; Pennemann et al. 2004). Microreactors in their most compact version comprise chemical chip systems, i.e., made by silicon micromachining, glass photoetching, and plastic engineering. Fist- and shoebox-sized laboratory and pilot units, respectively, are adequately termed microstructured reactors and conveniently made by means of steel etching, microelectro-discharge machining, and precision engineering such as milling, turning, or punching. In a few cases, much larger units were developed with outer dimensions in the meter range, in one case extended to even storey size (Markowz et al. 2005). Today, specialized microstructured equipment is available for many chemical engineering operations such as gas, liquid, gas–liquid, and liquid–liquid processing, largely without involving solids (Hessel et al. 2004a, 2005d; Ehrfeld et al. 2000; Jensen 1999, 2001; Fletcher et al. 2002; Haswell and Watts 2003; Gavriilidis et al. 2002; Jähnisch et al. 2004; Kolb and Hessel 2004; Pennemann et al. 2004). This is further

Microreactors

207

expanded to catalytic operations by insertion of a catalyst on carriers, most often as coated layers or mini fixed beds, or as thin pure catalyst films (Kiwi-Minsker and Renken 2005; Kolb and Hessel 2004). For many single-phase liquid operations, which comprise the majority of organic reactions, the connection of only two fluidic elements is sufficient to replace the commonly used mini-batch reactors, i.e., the typical stirred glass-lined, multiple-necked vessels with reflux condensers (Hessel et al. 2004a; Fletcher et al. 2002; Haswell and Watts 2003; Jähnisch et al. 2004; Pennemann et al. 2004). A micromixer is followed by an integrated microreactor–micro-heat exchanger or a more simply heated microreactor, providing the needed mixing, heating/ cooling, and reaction time functions. At the edge of very fast reactions, the micromixer also operates as a reactor, and the reaction is completed here, with no need for any other unit. At the edge of slower reactions, typically in the range of several minutes to as much as an hour, the micromixer is connected to a long residence unit, typically a capillary, and often only the capillary itself is used, with no need for a micromixer. Simple mixing tees then bring the reactants together, or even premixed solutions are used. Different types of micromixers exist based on different passive mixing principles (Hessel et al. 2004b). One class utilizes only diffusion at the micro scale by creating the finest geometric fluidic elements (jets, lamellae, etc.). A second class generates a recirculation flow to use convection, and then diffusion. A few micromixers are based on turbulence, since channel-free jets collide frontally at very high velocity, or flows at sufficiently high Reynolds numbers are achieved in comparatively large mixing channels. Besides micromixers, compact fluidic or electrically driven micro-heat exchangers were developed (Schubert et al. 2001). In the field of gas–liquid systems, falling film microreactors, Taylorflow and annular-flow channel contactors, and mini-trickle bed reactors are most often used (Hessel et al. 2005a). For liquid–liquid operation, slug-flow capillary reactors are one suitable reactor concept (Burns and Ramshaw 2001). Special dual- and triple-feed channel architectures can create droplets (Link et al. 2004; Utada et al. 2005; Joanicot and Ajdari 2005) or particles (Xu et al. 2005) of unique or uniform shape or with uniformly structured morphology or chemical composition, which are often changed by simple process parametric variation. This stems from

V. Hessel et al.

208

the well-defined flow patterns and concentration and temperature fields of the microflows. From the very beginning, continuous reactor concepts, an alternative to the truly microfabricated reactors, were used, for example, static meso-scaled mixers or HPLCs and other smart tubing (see Iwasaki et al. 2006 for an example). This completed functionality by filling niches not yet covered by microfabricated reactors or even by replacing the latter as a more robust, more easily accessed or more inexpensive processing tool. Further innovative equipment, coming from related developments in the process intensification field, is another source: e.g., structured packings such as fleeces, foams, or monoliths.

2

Microreactor Processes and Plants

In the last few years, the corresponding process technology and plants for microstructured reactors have been established, both by new customized process-flow environments from specialized providers (see Fig. 1) and by retrofit into existing plants at the company site. This named the disciplines of microprocess technology and engineering. The microprocess technology plants can have a shorter time-tomarket, better scale-out predictability, a higher degree of modularity, less stringent legislation, and are principally transportable or easy to dismount (Deibel 2006). Thus, even industry captains and leaders draw the conclusion that, sooner or later, parts of the existing plants will be replaced by the new technology and that the classical world-scale plant tends to be a phase-out model (Deibel 2006; Roberge 2006; Belloni 2006). Market studies are coming to similar conclusions (Arthur de Little 2006; Pieters et al. 2006). A paradigm change in plant engineering is quoted, governed by time-to-market (too late with products) and standardization issues (Deibel 2006). Here, microprocess engineering will have a role, based more on plant philosophy than on absolute size. Two main fields of application have been explored: fine chemistry/ pharmacy (Hessel et al. 2004a) and fuel processing (Hessel et al. 2005d). A few investigations target manufacture of bulk chemicals or intermediates. In addition, the production of smart and functional materials is the focus, such as pigments (Wille et al. 2004), encapsulated delivery

Microreactors

209

Fig. 1. Demonstration of microprocess technology plant for fine chemistry at IMM

systems (Wischke et al. 2006; Freitas et al. 2003), liquid-crystalline droplets (Fernández-Nieves et al. 2006), or chromatography beads (Kubo et al. 2006), just to name a few. Future investigations will cover personal care, household, and food applications. In the context of this paper, only the microdevices and the microprocess engineering for uses in fine chemistry and pharmacy are considered. The view will be process-based and deduced from a rough economic calculation of how mature the technology is and what needs to be done to promote it further.

3

Cost Analysis for General Judgment of Microreactor Competitiveness

3.1

Case of Low Plant Costs: Kolbe-Schmitt Synthesis

Fine-chemical processes convert raw materials to higher-value materials with a total annual value much higher than the costs of a typical microprocessing plant and its engineering. To illustrate this, the example of

210

V. Hessel et al.

the aqueous Kolbe-Schmitt synthesis from resorcinol to 1,4-dihydroxy carboxylic acid is taken (Hessel et al. 2005b), although the range of respective materials costs in fine chemistry and in microreactor plant cost is quite wide and it cannot be taken for granted that this example is representative.

Nonetheless, this reaction is certainly not at the most profitable edge, as the reaction time even in the microreactor is ultimately not short, still on the order of 1 min, and the reactor load is further limited by dissolubility of the reactants. Both limit the reactor space–time yield and thus decrease the productivity so that the following conclusions do not at all comprise a best-case scenario. As shown in Fig. 2, the raw materials costs for the Kolbe-Schmitt synthesis amount to approximately 40 e/kg, the target product amounts to about 124 e/kg (U. Krtschil et al., unpublished data). A fivetube microprocessing plant, which is a realistic numbered-up forecast from experimental kinetic data from a single-reactor operation, can achieve about 4.4 t/a, which corresponds to process volumes rated to reactants and products of 176 and 546 ke/kg. The cost of a five-reactor microprocessing plant for the Kolbe-Schmitt synthesis amounts to less than 30 ke. The capital costs total 1.12 e/kg, if a 10-year lifespan and 7-year amortization are assumed. It is evident from these numbers that the costs of a microreactor plant are not prohibitively high, although a complete cost analysis needs to incorporate much more data. This is further corroborated by an analysis of the waste disposable, which amounts to 15 e/kg for the Kolbe-Schmitt synthesis. Since it has been demonstrated many times that microprocess engineering can enhance selectivity significantly, this share of the costs should also be reduced substantially, further improving the costing balance in favor of the microreactors. This could not be demonstrated for the Kolbe-Schmitt synthesis of resorcinol; however, for the same synthesis with phloroglucinol, a 20% increase in yield was found (Hessel et al. 2007).

Microreactors

211

Fig. 2. Cost analysis for the aqueous Kolbe-Schmitt synthesis for the high-p,T base case

The central elements determining the costs of the microprocessing plant for the Kolbe-Schmitt synthesis are the peripherals such as two pumps, a chilling unit, and a thermostat, while the microreactor equipment includes a micromixer, a capillary as a reactor module, and a micro-heat exchanger for temperature quenching (Hessel et al. 2005b). There are certainly more complex plant process flows for other reactions at a comparable throughput, for instance with many more and more costly microstructured reactors, as well as more and more costly peripherals, while in this example the pumps are the dominating capital cost factor. The sulfonation of aromatics such as toluene is a case in point, which has a gas–liquid reaction with the dedicated and costly falling film microreactor as the central step and requires several downstream microprocessing operations for reaction completion, documented in Müller et al. (2004). The number of pumps here is increased to at least six, dependent on the exact configuration. In addition, control equipment was not considered in the cost analysis for the Kolbe-Schmitt synthesis, which can substantially increase the plant costs. Taking this into

212

V. Hessel et al.

account and following the price scheme for microreactors and peripheral equipment as noted for the Kolbe-Schmitt synthesis, microprocessing plants in fine chemistry may cost as much as 500 ke, just to give a figure, although there is no real upper limit here. Nonetheless, this rough estimation should serve here to demonstrate that microprocessing plant costs for fine chemistry themselves have a large spread from low costs to be in the order of the product value per year, in other words, substantial. In the following, first the common case of a micromixerreactor plant, as given for Kolbe-Schmitt synthesis, is considered, with low plant costs, and then a case needing a more advanced plant for largescale production is given. Since the capital costs the Kolbe-Schmitt synthesis are thus competitive with existing technology, the operational costs of such novel continuous synthesis need to be determined. The energy and production site costs were found to be negligible. Therefore, the only uncertain cost share remains the labor costs. This is certainly the most difficult parameter in the cost analysis, since the share of labor time of the operator per microreactor plant cannot be theoretically calculated, but needs to be determined by future experience. At present, an operator share based on industrial experience with batch plants was taken as a first estimation. In this way, labor costs amounted to 36 e/kg, i.e., they were nearly as high as the raw material costs. The main figure for calculating such labor costs, besides the number of plants controlled by one operator, is the productivity of plant operation, which inversely goes along with the reaction time, i.e., which is proportional to the speed of the reaction. 3.2

The Case of High Plant Costs, Hypothetical Reaction

The relevant shares in the cost calculations change when microprocess technology approaches large-scale chemical production (U. Krtschil et al., unpublished data). Reactor fabrication at a competitive cost becomes crucial and is among the main cost drivers. The corresponding costs here go with the overall size of the microstructured reactor and with its number. A hypothetical reaction with assumed properties was taken, since no real-case reaction was available for demonstration. Liquid-phase operation for a homogeneously catalyzed pseudo-first-order reaction was

Microreactors

213

considered. Calculations were made using the Arrhenius equation with the pre-exponential factor of 4 × 106 l/(mol s) and the activation energy 5 × 104 J/mol. A reaction velocity constant of 0.01 1/s was assumed at a temperature of 100°C. In the next step, the temperatures corresponding to reaction velocity constants of 0.1, 0.05, and 1 1/s were calculated. The reaction times for a 95% conversion were derived in this way, and using these data microstructured plate reactors for use in large-scale chemical production were dimensioned. The overall capacity was set to 10,000 tons of product per year. One microstructured reactor unit has a width, height, and length of 0.25 m × 0.35 m × 0.5 m. Today’s microfabrication techniques for steel can still machine such extended areas; however, this is at the upper edge of what can be commercially processed. Still larger reactor units would demand a technology change to mass manufacture techniques such as rolling for microstructuring steel plates (see Fig. 3) and brazing for their interconnection. To comply with other calculations of these larger microstructured reactors, this was taken as the cost basis in this case as well (and not the current practices in chemical etching and laser welding). Channel dimensions were set to 0.5 mm deep, 1 mm wide, and 0.5 m long to meet the capacity requirements. Reaction times ranged from 3 s to 5 min, depending on the temperature. Figure 4 shows the impact of process intensification for this hypothetical case. With a temperature increase of only 41°C, the number of reactors for such comparatively big units is reduced from 20, hardly feasible in view of costs and process control, to four, feasible for the same reasons. Thus, the costs decrease by almost a factor of five (not exactly, since fixed costs have a small share). Another 21°C temperature increase halves the number of reactors again, and at 249°C, which is 149°C higher than the base temperature, an equivalent of 0.2 microstructured reactors is needed. This means that practically one microstructured reactor is taken and either reduced in plate number or in the overall dimensions. The costs of all microstructured reactors scales largely with their number; only at very low numbers do fixed costs for microfabrication lead to a leveling off of the cost reduction. In another cost analysis, a commercial fine-chemical synthesis using microprocess technology, developed and undertaken by the AzurChem Company, was investigated (Krtschil et al. 2006). Using real-life data,

214

V. Hessel et al.

Fig. 3. Roll for mass fabrication of microstructured steel plates. The endless sheet can be moved at least at a velocity of 1 m/min, i.e., for a plate length of 10 cm and rolling four microstructured units in parallel, 2,400 plates/h can be manufactured. Structural dimensions of 500 µm have so far been realized; the technique is expected to yield microstructures at a100-µm characteristic width

the findings of the Kolbe-Schmitt synthesis were confirmed with the example of phenyl boronic acid synthesis. Here, selectivity has a much higher impact, as both starting and product materials are very costly. In addition to the real case, three other hypothetical microflow cases and one hypothetical batch case were considered to give an outline of how process protocol variations might have an impact (see Fig. 5). This includes a five- and tenfold capacity by process intensification (novel chemistry concepts) or a tenfold parallel microreactor operation (numbering-up). In addition to showing their impact on the cost structure, the resulting earnings and total costs are given. Without further detailing such analysis, reported comprehensively elsewhere, some simple rules for cost-efficient microprocess technology fine-chemical synthesis can be given. The first rule is to select fast

Microreactors

215

Fig. 4. Impact of process intensification on a hypothetical homogeneously catalyzed liquid reaction. Number of parallel operating reactors depending on the reaction temperature

chemical processes. An investigation by the company Lonza has shown that approximately 44% of all industrial processes fulfilled this criterion within 1 year; 17% when considering the current practical limitations (Roberge et al. 2005). On the other hand, this means that one must question whether there is unreleased potential or whether the rest of the reactions are perhaps not suitable. Thus, the second issue is to check if and how one can transform otherwise slow processes into fast ones. The analysis also showed the need to select high-value reactants and products, which is given for expensive fine chemicals and pharmaceutical products and for most advanced and functional materials. In turn, microfabrication costs are often negligible (but only in case of success). Preliminary cost analysis calculations show, however, that for bulk chemistry, fuel processing, consumer goods, etc., reactor and energy costs have an impact. Mass manufacture of microreactor plates is the key here to cost-efficient reactor provision.

V. Hessel et al.

216

Fig. 5. Earnings and total costs for a commercial microreactor process, for the real-life micro-flow case, three processes intensified or numbered-up microflow cases, and a batch benchmark case (Courtesy of Swiss Chemical Society)

4

New Process Windows: Speed up Microreactor Chemistry

The arguments given above underline that using a microreactor without a high degree of parallelization or without speeding up the reaction may not be economically competitive. On the other hand, taking these two measures into account, there is a wide range of microreactor cost performance. Thus, the lesson to be learned from this is that one should not passively use microreactors by applying established chemical protocols, but rather actively re-think the chemical protocols themselves to achieve a significant improvement in technical and cost performance. This seems to contradict the general rule of process intensification and microprocess technology requiring that the reactor be designed around the reaction rather than adapting the reaction to make it compatible with the reactor. However, basically this is extending that rule by saying that in order to tap the full potential of microprocess technology, a revision and re-thinking of the chemistry itself is required, i.e., it needs to be

Microreactors

217

shifted to the more extreme edges of the processing window, for example, in terms of temperature, pressure, concentration, shortness of residence time, etc. Basically, it is not surprising that the chemistry developed over centuries for slowly processing batches is not ideal for extremely fast-acting reactors. For this reason, a chemical protocol design strategy called initially novel chemistry and re-named recently new process windows (Hessel et al. 2005c) was proposed, including three sources of information, which are prior scattered works in the field of organic chemistry (including some geochemistry papers; Siskin and Katritzky 1991), specific research in the field of the emerging interdisciplinary fields such as microprocess technology or microwave synthesis, and some predictions we have developed to complete the picture. The cornerstones of the new process windows concept are: – – – – – – –

Direct routes from hazardous elements Routes at increased concentration or even solvent-free Routes at elevated temperature and/or pressure Routes mixing the reactants all at once Routes using unstable intermediates Routes in the explosive or thermal runaway regime Process simplification – e.g., routes omitting the need of catalysts or (complex) separation

In particular, inspired by our own work was the second concept, termed high-p,T, which stands for combining high temperatures (to accelerate chemical processes) and high pressures (to prevent the solution in the microreactor from boiling and keep it in the liquid phase). Although this is a trivial measure and certainly was done before using conventional technology, microprocess technology adds a low technical expenditure and improved safety when exploring such explosive or hazardous regions in the process window. Thus, while being possible in the past, microreactors largely expand the applicability of high-p,T processing. The same is utilized in microwave processing, showing an increasing number of continuous applications, and has been named encased processing. In this way, typical organic protocols can be shifted from about 130°C maximal operational temperature (depending mostly on the choice of

218

V. Hessel et al.

solvent, with the exception of the less frequently used DMF and DMSO with lower boiling points) to 200°C and higher. Typical pressures applied are 50 bar and higher to ensure single-phase operation with a large safety margin.

An idea on the impact of high-temperature processing was provided by calculating the time needed for a 90%-conversion degree based on the Arrhenius equation, assuming a first-order reaction with the enhancement factor A = 4 × 1010 mol–1 s–1 and the activation energy Ea =100 kJ mol–1 (Kappe and Stadler 2005). This shows that order of magnitude changes can be achieved with practicable increases in reaction temperature. With simply an increase of roughly 100°C, reactions formerly taking days are shortened to hours and those formerly taking hours need only a few seconds. This was verified by microwave processing on its own and by combined use of microwaves and microflow processing. It stands to reason that such considerations only target conversion (and reaction rate consequently) and do not take into account selectivity which may dramatically decrease at high temperatures by decomposition or side reactions. To control the latter, shortening residence times is one approach. The high-p,T effect was demonstrated at the example of the aqueous Kolbe-Schmitt synthesis of resorcinol (see formula given above) by performing microflow processing on its own, using a pressurized capillary, if needed equipped with a micromixer upfront and a micro-heat exchanger for temperature quenching downstream (Hessel et al. 2005b). Table 1 Temperature [◦ C] 27 77 127 177 227 Rate constant k [s−1 ] 1.6 × 10−7 4.8 × 10−5 3.5 × 10−3 9.9 × 10−2 1.43 Time (90% conversion) 68 days 13.4 h 11.4 min 23.4 s 1.61 s

Microreactors

219

Experiments were conducted at a pressure of 40–70 bar, a temperature of 100–220°C, and reaction times of 4–390 s. It was cross-checked and confirmed that the textbook recommended reaction time of 2 h at least roughly constitutes the actual kinetically needed reaction time at the standard batch conditions of 100°C and 1 bar (which is usually not the case; over-reaction is common in organic synthesis). Using the high-p,T microreactor processing, the Kolbe-Schmitt synthesis was completed within less than 1 min at comparable yields, i.e., a reaction time reduced by a factor of approximately 2,000 was achieved (see Fig. 6). This corresponds to an increase in space-time yield by a factor of 440. As can be expected, the high-temperature processing runs the risk of enhancing side and consecutive reactions. Decarboxylation of the main product was found and increases with temperature (see Fig. 7). This is illustrated at the example of the synthesis of 2,4,6-trihydroxy benzoic acid from phloroglucinol, as this molecule is even more sensitive to thermal destruction due to the enhanced electron richness of the aromatic core by presence of a third hydroxyl group (Hessel et al. 2007).

Fig. 6. Process intensification of the aqueous Kolbe-Schmitt synthesis of resorcinol using high-p,T processing. (Courtesy of ACS)

220

V. Hessel et al.

Thus, there is a small process window where high-p,T processing is effective and process control may have an important role here to maintain processing at optimal conditions. Figure 8 illustrates how delicate the impact of residence time and temperatures is. Optimal performance is only achieved at short times not exceeding a few minutes and overshooting the temperature by roughly 10°C can already notably decrease the yield. Similar process intensification was obtained for the Michael addition with α, β unsaturated amines and esters (Löwe et al. 2006). Microstructured reactors made it possible to take advantage of the fast kinetics of the Michael addition reaction, while still ensuring efficient heat removal and avoiding thermal overshooting. Yields ranging from 95% to 100% were obtained, at reaction times of 1–10 min instead of the 24-h batch operation; a high-p,T operation was established. High

Fig. 7. Process intensification and adverse thermal destruction effects of the aqueous Kolbe-Schmitt synthesis of phloroglucinol using high-p,T processing. (Courtesy of Wiley-VCH)

Microreactors

221

Fig. 8. Adverse thermal destruction effects of the aqueous Kolbe-Schmitt synthesis of phloroglucinol using high-p,T processing. (Courtesy of Wiley-VCH)

productivities were achieved, for example, 100 g piperidino-propionitrile in 13 min ≈ 9 l/day.

5

Some Thoughts on Scale-out of Microprocess Technology

Different methods for scale-out have been collected and presented (Löb et al. 2006a). The two main methods are a smart scale-up, at best after having intensified the process, or the internal numbering-up concept. The first route was shown long ago by the Merck production case for an organometallic reaction, changing from micro- to mini-mixers (Krummradt et al. 2000). This route seems to be feasible, as long as

222

V. Hessel et al.

there is single-phase operation and a potential for process intensification. Then, by use of one microstructured device, most often a mixer, connected to a tube, production can be achieved simply. Since micromixers are short, the pressure drop is low and, in turn, high throughputs can be achieved. There are, however, known laboratory case studies in fine chemistry that will demand much more dedicated reactor design when moving to a pilot reactor design. This holds true, for example, for reactions that need advanced thermal management, multiphase reactions, and relatively slow reactions (even when intensified). The corresponding pilot reactors will be highly numbered-up, highly integrated, and/or have a long flow axis. This means the corresponding pilot reactors will have comparatively large dimensions overall and may become costly due to a comparatively huge mass of construction material and large-area microfabrication. At this point of development, these pilot reactors are just beginning construction. In the following, the reasons for the higher architectural demands are exemplified at two laboratory examples for liquid–liquid Suzuki coupling and imidazol-based ionic liquid synthesis and can only partly be shown in the example of liquid–liquid and gas–liquid processing scaleout. 5.1

Liquid–Liquid Dispersion for Suzuki Coupling: A Redispersion Reactor

The dispersion of organic solvents and aqueous solutions, commonly found in phase-transfer reactions, in a continuous mode by the simple use of microstructure mixers is a difficult operation, since in most cases fast coalescence of the created droplets may be found, possibly slowing down the reaction. One solution is the repeated break-up of droplets. A redispersion mixer-reactor with four dispersion stages was developed. The basic function was proven with dyed aqueous solution with the surfactant sodium dodecyl sulphate and heptane, as shown in Fig. 9. The coarse droplet system, premixed using an external micromixer (not shown), is dispersed more finely from stage to stage (see Fig. 9). The stage-wise redispersion leads to an extended reactor length, and accordingly the flow per channel or unit is kept relatively low, leading to pilot

Microreactors

223

Fig. 9. Stage-wise breakup of a coarse droplet mixture in a redispersion microreactor. (Courtesy of Wiley-VCH)

designs with a higher degree of numbering-up and with extended reactor length. The redispersion microreactor is applied for the liquid–liquid polycondensation to yield an OLED material by multiple Suzuki coupling. As the initial test reaction, the following single Suzuki coupling is currently being explored in the liquid–liquid system made from water/ dioxane/toluene.

Measurements with the latter real-case solvent system give a more complex picture. Even for the one-plate design, achieving uniform flow conditions in each channel is an open issue. Preliminary experiments show that high-temperature, high-pressure operation gives better flow uniformity, which is also advantageous to speed up the polycondensation reaction (see Fig. 10). 5.2

Solvent-Free Ionic Liquid Synthesis with Large Heat Release: Capillary or Integrated Reactors

An imidazol-based ionic liquid synthesis was carried out under solventfree conditions, simply bringing the two liquid reactants into contact

224

V. Hessel et al.

Fig. 10. Top images: Improved flow distribution of the liquid–liquid slug flow at 80°C and 5 bar at the reactor inlet (left) and the reactor center (right). Less regular flow distribution of the liquid–liquid slug flow at 20°C and 1 bar at the reactor inlet (left) and the reactor centre (right)

(Löb et al. 2006b). Because of the high reactor load and large exothermicity of the reaction, the heat releases are quite strong. In-line temperature measurements in a micromixer-capillary set-up cooled by a temperature bath confirm the existence of hot spots of much more than 50°C in the capillary (see Fig. 11). This can be overcome by using a multiscaled capillary design or by integrating heat exchange and reaction channels within one microreactor unit, both at the expense of an increasing drop in pressure. Thus, pilot-sized reactors will be highly numbered up or highly integrated. This additional expenditure in reactor design is, however, outweighed

Microreactors

225

Fig. 11. Real-time, in-line temperature monitoring for an ionic-liquid synthesis when varying external bath temperature and volume flow

by the process intensification through fast, high-temperature, solventfree continuous processing. Yoshida et al. developed similar numbered-up capillary pilot reactors for free radical polymerization (Iwasaki et al. 2006). The capillaries were either arranged in parallel fashion similar to conventional multitube reactors or consecutively branched by multiport valves. 5.3

Gas–Liquid Processing Scale-out: Falling Film Microreactor

The falling film microreactor has been applied to a number of different reactions and has been characterized for mass transfer at the laboratory scale. In a running German BMBF project with Degussa as the industrial partner, scaled-out falling film microreactors are being developed; they have a tenfold larger structured area (150 cm2 ) and a correspondingly larger film surface compared to their laboratory counterparts (Vankayala et al., unpublished data). One pilot microstructured reactor refers to the numbering-up concept with a more compact arrangement of an increased number of microchannels on a cylindrical body (see

226

V. Hessel et al.

Fig. 12). External numbering-up by flow manifolding to separate reactor units is here one concept for future production reactors with another tenfold increase in structured area. Another pilot microstructured reactor uses a smart scale-up of the reactor plate dimensions by a factor of 3.3, each for the width and channel length (see Fig. 13). Stacking further plates is here one concept for future production reactors with another tenfold increase in structured area. Using an industrial oxidation reaction and carbon dioxide absorption in aqueous alkaline solutions, it was validated in some sets of process conditions that such pilot reactors show similar performance as their

Fig. 12. Cylindrical falling film microreactor for pilot operation at tenfold capacity increase as compared to the laboratory falling film microreactor

Microreactors

227

laboratory counterparts. At best, a selectivity of 90% at a conversion of up to 80% was achieved. By operating at 10 bar, increases in yield by 5%–15% (within the flow rate range investigated) were found in 1,200-µm-wide microchannels, as compared to atmospheric pressure, which again demonstrates the need for intensified processing when using microprocess technology. Future issues for an improved pilot reactor design remain achieving and confirming the same falling film profile in the microchannels for the laboratory and pilot reactor. The film shapes are complex and theoretical predictions seem to fail to accurately describe them. It stands to reason that such thin films have a dedicated dependence on the details

Fig. 13. a,b Scaled-out large falling film microreactor for pilot operation at tenfold capacity increase compared to the laboratory falling film microreactor

228

V. Hessel et al.

Fig. 13. a,b (continued)

of the microchannel encompassing them. In their current version, laboratory and pilot falling film microreactors may differ in the surface energies and cross-sectional shapes of their microchannels because of the need to apply different microfabrication technologies or to have varying qualities of microfabrication for the same technology. While chemical etching is used to make the microchannels at the laboratory-scale plates of the falling film microreactor, microelectro-discharge machining was the adequate preliminary approach to the cylindrical pilot design. For the scaled up pilot design, chemical etching was suitable to make both the small laboratory and the large pilot plates. Still, as etching is done by a spray technique from a punctual source to wet and abrase a flat body, there may be differences in microstructured quality at varying plate scales. Actually, slight conversion increases were found: cylindrical FFMR B large-plate FFMR B standard FFMR. This is due to different settings of residence time and film thickness, which come from the above-

Microreactors

229

mentioned slightly different geometric specifications. Film thickness is the central, often unknown parameter for scale-out, as standard correlations such as the Kapitza, Feind, or Nusselt equation are only accurate by one order of magnitude and the demand for additional experimental determination is difficult in routine operation. Such effects of microstructuring on channel geometry and surface energy are under investigation.

6

Industrial Production Cases

6.1

Nitroglycerine Production Plant

A nitroglycerine microprocessing plant, developed by IMM for the Chinese class-A company Xi’an, is an example of the smart scaled-out concept, showing that just one caterpillar micromixer is sufficient for the continuous production of pharmaceutical-degree nitroglycerine, with a throughput of approximately 15 kg/h (Thayer 2006).

The manufactured nitroglycerine will be used as a drug for acute cardiac infarction. Therefore, the product must be made under GMP conditions and the quality of the product has to meet the highest standards. The microstructured reactor plant consists essentially of three main parts (see Fig. 14): mixing sulfuric acid with nitric acid, with highly concentrated fuming liquids, the reactor and the phase separation, and washing and purification devices. On demand, glycerine and the acid mixture are fed separately into a microstructured reactor where mixing occurs within milliseconds. The high surface-to-volume ratio of these new types of reactors ensures an immediate transfer of heat released by the reaction. Increased safety compared to conventional processing is achieved by the small volume hold-up in the microstructured reactor. In summary, higher yields, better product quality, increased safety, and a reduction in environmental hazards are the main advan-

V. Hessel et al.

230

Fig. 14. Nitroglycerine production microprocess plant with staff at industrial site in Xi’an, China

tages of applying microstructured reactors to this type of chemical reaction. 6.2

Radical Polymerization Plant

A pilot plant for free-radical polymerization was developed at Kyoto University (see Fig. 15) and transferred to the industrial site at the Idemitsu Kosan Company (Iwasaki et al. 2006). Two microprocess technology concepts were evaluated based on different multicapillary designs (see Fig. 16). For the superior performance design with consecutive, multiply furcated capillaries using conventional manifolds, flow distribution quality was determined. Polydispersity indices for eight capillaries ranged from 1.66 to 1.71, i.e., it showed a low spread, demonstrating that flow distribution was reasonably achieved. The molecular number average was

Microreactors

231

Fig. 15. Radical polymerization reaction pilot microprocess plant (Courtesy of ACS)

18,000 at a low yield of approximately 6%. Stable process operation over a period of 7 days was demonstrated by showing an almost constant degree of polymerization and polydispersity index. 6.3

Grignard Exchange Reaction Plant

Another pilot plant, developed by at Kyoto University, was used for the Grignard exchange reaction at the same productivity as the batch reactor (10 m3 ) by adding only four microflow systems of the present scale (Wakami and Yoshida 2006). A multitubular reactor is the core element of the microprocessing plant (see Fig. 17). Stable yields of approximately 95% could be demonstrated for a 24-h run. 6.4

Swern-Moffat Oxidation Plant

Figure 18 shows a pilot plant with a capacity of 10 t/a built for SwernMoffat oxidation (Kawaguchi et al. 2006). The microreactor includes a series of rapid mixing functions for mass production. The yield of

232

V. Hessel et al.

Fig. 16. a,b Two parallel microcapillary connection concepts: tube-and-shell multitubular and branched tube arrangements (Courtesy of ACS)

Microreactors

233

Fig. 16. a,b (continued)

the batch process is 83% at –70°C, whereas the microchemical process achieved a yield of 88% at 20°C. The pilot plant could be operated stably for a long run with the same product yield as the laboratory experiment. 6.5

Yellow Nano-Pigment Plant

Figure 19a shows a pilot plant for the production of a yellow nano pigment with a capacity of 70 t/a, developed and operated by Kyoto University and Fuji Company (Maeta et al. 2006). Figure 19b shows some selected particle-size spectra obtained under various flow conditions.

V. Hessel et al.

234

Fig. 17. Multitubular reactor used for the Grignard exchange reaction pilot microprocess plant. (Courtesy of ACS)

6.6

Polymer Intermediate Plant

A customized microstructured reactor, approximately shoebox-size, for manufacturing a high-value polymer intermediate was developed at Forschungszentrum Karlsruhe and installed in an industrial environment (FZK press release 13, 2005). During a 10-week production campaign, over 300 tons of a polymer intermediate product were manufactured for the plastics industry. A microstructured reactor, made from a special nickel alloy, 65 cm long and weighing 290 kg, was the central element of this new production plant. With a throughput of 1,700 kg of liquid chemicals per hour, this reactor was able to meet the demands for a chemical production line. It clearly fits the remarks concerning

Microreactors

235

Fig. 18. Swern-Moffats reaction pilot microprocess plant. (Courtesy of ACS)

microstructured reactors made above. The interior of the reactor consist of a multitude of microchannels, while the entire reactor is much bigger and heavier than the term “micro” implies. In this way, a central reaction route in industry has been replaced, which was conducted before in a very large reactor tank.

7

Conclusions and Outlook

Microreactor and microprocess technology has, in some fine-chemical cases, approached commercial applications and become competitive with existing technology. Two main developments are awaited. Firstly, optimizing the process protocol conditions such that the chemistry is set to the limit of the reactor’s capabilities in terms of mass and heat transfer. This so-called novel chemistry approach achieves the highest process intensification and can improve the costing of microprocess

236

Fig. 19. a Yellow nano pigment pilot microprocess plant

V. Hessel et al.

Microreactors

237

Fig. 19. b Particle-size spectra at various volume flows

plants by another order of magnitude. Secondly, new large microstructured reactors need to be built for large-scale applications in general and for more complex operations in particular, such as combined mixing and heat exchange at high mixing sensitivity and/or large heat releases. Here, a paradigm shift in microreactor fabrication using mass manufacture is needed and costing analyses have to be made on a much more complex level. To achieve competitiveness, process intensification is even more necessary than for fine-chemical synthesis. In addition, the costing, the ease, speed, and predictability of scale-out of microprocess technology will largely govern the industrial implementation.

References Arthur de Little, SenterNovem (2006) Full study presented to platform for chain efficiency (PKE). Building a business case on process intensification Belloni A (2006) Process 13:64–65 Burns JR, Ramshaw C (2001) The intensification of rapid reactions in multiphase systems using slug flow in capillaries. Lab Chip 1:10–15 Deibel S-R (2006) Anlagenbau: Schneller planen, rascher produzieren. CHE Manager 2:12

238

V. Hessel et al.

Ehrfeld W, Hessel V, Löwe H (2000) Microreactors: new technology for modern chemistry. Wiley-VCH, Weinheim Fernández-Nieves A, Christobal G, Garcés-Chávez V, Spalding GC, Dholakia K, Weitz DA (2006) Optically anisotropic colloids of controllable shape. Adv Mat 17:680–684 Fletcher PDI, Haswell SJ, Pombo-Villar E, Warrington BH, Watts P, Wong SYF, Zhang X (2002) Tetrahedron 58:4735 Freitas S, Walz A, Merkle HP, Gander B (2003) Solvent extraction employing a static micromixer: a simple, robust and versatile technology for the microencapsulation of proteins. J Microencapsulation 20:67–85 FZK Press release 13 (2005) http://www.fzk.de/fzk/idcplg?IdcService=FZK& node=2374&document=ID 050927. Cited 6 July 2005 Gavriilidis A, Angeli P, Cao E, Yeong KK, Wan YSS (2002) Trans IChemE 80/A:3 Haswell ST, Watts P (2003) Green Chem 5:240 Hessel V, Hardt S, Löwe H (2004a) Chemical micro process engineering— fundamentals, modelling and reactions. Wiley-VCH, Weinheim Hessel V, Löwe H, Schönfeld F (2004b) Micromixers—a review on passive and active mixing principles. Chem Eng Sci 60:2479–2501 Hessel V, Angeli P, Gavriilidis A, Löwe H (2005a) Gas-liquid and gas-liquidsolid microstructured reactors—contacting principles and applications. Ind Eng Chem Res 44:9750–9769 Hessel V, Hofmann C, Löb P, Löhndorf J, Löwe H, Ziogas A (2005b) Aqueous Kolbe-Schmitt synthesis using resorcinol in a micro-reactor laboratory rig under high-p,T conditions. Org Proc Res Dev 9:479–489 Hessel V, Löb P, Löwe H (2005c) Development of microstructured reactors to enable organic synthesis rather than subduing chemistry. Curr Org Chem 9:765–787 Hessel V, Löwe H, Müller A, Kolb G (2005d) Chemical micro process engineering—processing and plants. Wiley-VCH, Weinheim Hessel V, Hofmann C, Löb P, Löwe H, Parals M (2007) Micro-reactor processing for the aqueous Kolbe-Schmitt synthesis of hydroquinone and phloroglucinol. Chem Eng Technol 31, (in press) Iwasaki T, Kawano N, Yoshida Y-I (2006) Radical polymerization using micro flow system. Numbering-up of microreactors and continuous operation. Org Proc Res Dev 10:1126–1131 Jähnisch K, Hessel V, Löwe H, Baerns M (2004) Chemistry in microstructured reactors. Ang Chem Int Ed 43:406–446 Jensen KF (1999) Microchemical systems: status, challenges, and opportunities. AIChE J 45:2051–2054

Microreactors

239

Jensen KF (2001) Microreaction engineering – is small better? Chem Eng Sci 56:293–303 Joanicot M, Ajdari A (2005) Droplet control for microfluidics. Science 309:887–888 Kappe CO, Stadler A (2005) Microwaves in organic and medicinal chemistry, Vol. 25. In: Mannhold R, Kubinyi H, Folkers G (eds) Methods and principles in medicinal chemistry. Wiley, Weinheim, pp 94–95 Kawaguchi T, Miyata H, Ataka K, Mae K, Yoshida J-I (2006) Room temperature Swern oxidations by using a microscale flow system. Angew Chem Int Ed Engl 44:2413–2416 Kiwi-Minsker L, Renken A (2005) Microstructured reactors for catalytic reactions. Catalysis Today 110:2–14 Kolb G, Hessel V (2004) Micro-structured reactors for gas phase reactions: a review. Chem Eng J 98:1–38 Kubo A, Shinmori H, Takeuchi T (2006). Atrazine-imprinted microspheres prepared using a microfluidic device. Chem Lett 35:588–589 Krtschil U, Hessel V, Kralisch D, Kreisel G, Küpper M, Schenk R (2006) Cost analysis of a commercial manufacturing process of a fine chemical using micro process engineering. Chimia 60:611–617 Krummradt H, Kopp U, Stoldt J (2000) Experiences with the use of microreactors in organic synthesis. In: Proceedings of Microreaction Technology: 3rd International Conference on Microreaction Technology. Springer, Berlin Heidelberg New York, pp 181–186 Link DR, Anna SL, Weitz DA, Stone, HA (2004) Geometrically mediated breakup of drops in microfluidic devices. Phys Rev Lett 92:054503-1-4 Löb P, Hessel V, Krtschil U, Löwe H (2006a) Continuous micro-reactor rigs with capillary sections in organic synthesis—generic process flow sheets, practical experience, and “novel chemistry”. Chimica Oggi Chem Today 24:46–50 Löb P, Löwe H, Hessel V, Hubbard SM, Menges G, Balon-Burger M (2006b) Determination of temperature profile within continuous micromixer-tube reactor used for the exothermic addition of dimethyl amine to acrylonitrile and an exothermic ionic liquid synthesis. In: Proceedings of AIChE Spring National Meeting, Orlando, 23–27 April, 2006 Löwe H, Hessel V, Hubbard S, Löb P (2006) Addition of secondary amines to α,β-unsaturated carbonyl compounds and nitriles by using microstructured reactors. Org Proc Res Dev 10:1144–1152 Maeta et al (2006) Proceedings of the AIChE Spring National Meeting. Orlando, 23–27 April, 2006

240

V. Hessel et al.

Markowz G, Schirrmeister S, Albrecht J, Becker F, Schütte R, Caspary KJ, Klemm E (2005) Microstructured reactors for heterogeneously catalysed gas-phase reactions on an industrial scale. Chem Eng Technol 28:459–464 Müller A, Cominos V, Hessel V, Horn B, Schürer J, Ziogas A, Jähnisch K, Hillmann V, Großer V, Jamc KA, Bazzanella A, Rinke G, Kraut M (2005) Fluidic bus system for chemical process engineering in the laboratory and for small-scale production. Chem Eng J 107:205–214 Pennemann H, Watts P, Haswell S, Hessel V, Löwe H (2004) Org Proc Res Dev 8:422 Pieters B, Andrieux G, Eloy J-C (2006) Technologies and market trends in microreaction technology, Chimica Oggi Chem Today 24:41–42 Roberge DM, Ducry L, Bieler N, Cretton P, Zimmermann B (2004) Microreactor technology: a revolution for the fine chemical and pharmaceutical industries? Chem Eng Technol 28:318–323 Roberge DM, Hogan J (2006) A little goes a long way. Nature 442:351–352 Re-dispersion Microreactor for the formation of Liquid-Liquid Dispersions for Use in Polycondensation Siskin M, Katritzky AR (1991) Reactivity of organic compounds in hot water: geochemical and technological implications. Science 254:231–237 Schubert K, Brandner J, Fichtner M, Linder G, Schygulla U, Wenka A (2001) Microstructure devices for applications in thermal and chemical process engineering. Microscale Thermophys Eng 5:17–39 Thayer AM (2005) Harnessing microreactions. Chem Eng News Coverstory 83:43–52. Utada AS, Lorenceau E, Link DR, Kaplan PD, Stone HA, Weitz DA (2005) Monodisperse double emulsions generated from a microcapillary device. Science 308:537–541 Wakami, Yohsid J-I (2006) Grignard exchange reaction using micro flow system. From bench to pilot plant. Org Proc Res Dev 9:787–791 Wille C, Gabski H-P, Haller T, Kim H, Unverdorben L, Winter R (2004) Synthesis of pigments in a three-stage microreactor pilot plant—an experimental technical report. Chem Eng J 101:179–185 Wischke C, Lorenzen D, Zimmermann J, Borchert H-H (2006) Preparation of protein loaded poly(D,L-lactide-co-glycolide) microparticles for the antigen delivery to dentritic cells using a static micromixer. Eur J Pharma Biopharma 62:247–253 Xu S, Nie Z, Seo M, Lewis P, Kumacheva E, Stone HA, Garstecki P, Douglas B, Whitesides GM (2005) Generation of monodisperse particles by using microfluidics: control over size, shape, and composition. Angew Chem Int Ed 44:724–728

Ernst Schering Foundation Symposium Proceedings

Editors: Günter Stock Monika Lessl Vol. 1 (2006/1): Tissue-Specific Estrogen Action Editors: K.S. Korach, T. Wintermantel Vol. 2 (2006/2): GPCRs: From Deorphanization to Lead Structure Identification Editors: H.R. Bourne, R. Horuk, J. Kuhnke, H. Michel Vol. 3 (2007/3): New Avenues to Efficient Chemical Synthesis Editors: P.H. Seeberger, T. Blume

This series will be available on request from Ernst Schering Research Foundation, 13342 Berlin, Germany

New Avenues to Efficient Chemical Synthesis. Emerging Technologies

New Avenues to Efficient Chemical Synthesis: Emerging Technologies (Ernst Schering Foundation Symposium Proceedings)

Soft Mechanochemical Synthesis: A Basis for New Chemical Technologies

Soft mechanochemical synthesis: a basis for new chemical technologies

Emerging Technologies

Efficient Carbohydrate Synthesis

The new avenues in bioinformatics

Engaged Learning with Emerging Technologies

Watershed Health Monitoring: Emerging Technologies

Chemical Synthesis Using Supercritical Fluids

The Logic of Chemical Synthesis

MPLS-Enabled Applications: Emerging Developments And New Technologies

Entrepreneurial Strategies: New Technologies in Emerging Markets (Strategic Management Society)

MPLS-Enabled Applications : Emerging Developments and New Technologies

Biotechnological Innovations in Chemical Synthesis

Chemical Synthesis Using Supercritical Fluids

The Logic of Chemical Synthesis

Catalysts for fine chemical synthesis

Catalysts for Fine Chemical Synthesis

Biotechnological innovations in chemical synthesis

The Logic of Chemical Synthesis

The Logic of Chemical Synthesis

Electrochemical Microsystem Technologies (New Trends in Electro Chemical Technology, 2)

Information Communication Technologies and Emerging Business Strategies

New worlds, new technologies, new issues

Carbon Nanowalls: Synthesis and Emerging Applications

Brewing: New Technologies

New Vaccine Technologies

Mathematics for New Technologies

Emerging wireless multimedia services and technologies

Nanotechnology: Basic Science and Emerging Technologies

New Avenues to Efficient Chemical Synthesis. Emerging Technologies