Design of Flexible Production Systems

Design of Flexible Production Systems Tullio Tolio (Ed.) Design of Flexible Production Systems Methodologies and Tool...

Author: Tolio T. (ed.)

312 downloads 1452 Views 6MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

Design of Flexible Production Systems

Tullio Tolio (Ed.)

Design of Flexible Production Systems Methodologies and Tools

13

Professor Tullio Tolio Politecnico di Milano Dipartimento di Meccanica Via La Masa 1 I-20156 Milano [email protected]

ISBN: 978-3-540-85413-5

e-ISBN: 978-3-540-85414-2

DOI 10.1007/978-3-540-85414-2 Library of Congress Control Number: 2008935904 # Springer-Verlag Berlin Heidelberg 2009 This work is subject to copyright. All rights are reserved, whether the whole or part of the material is concerned, specifically the rights of translation, reprinting, reuse of illustrations, recitation, broadcasting, reproduction on microfilm or in any other way, and storage in data banks. Duplication of this publication or parts thereof is permitted only under the provisions of the German Copyright Law of September 9, 1965, in its current version, and permission for use must always be obtained from Springer. Violations are liable to prosecution under the German Copyright Law. The use of general descriptive names, registered names, trademarks, etc. in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant protective laws and regulations and therefore free for general use. Typesetting: Integra, India Cover design: eStudio Calamar, Spain Printed on acid-free paper 9 8 7 6 5 4 3 2 1 springer.com

Preface

Manufacturing Flexibility is usually considered as the main answer for surviving in present markets characterized by short lead times, tight product tolerances, pressure on costs, frequent changes in demand and continuous evolution of the technological requirements of the products. Even if flexibility can be seen on the one hand as an important strategic option, on the other hand one must consider that the competitiveness of a firm can be strongly affected by the burden of capital intensive investments in system flexibility. Therefore there is the need of viewing system flexibility in the global picture trying to consider both the advantages and the disadvantages related to the acquisition of flexibility. In particular production contexts characterized by mid to high demand volume of well identified families of products in continuous evolution do not require the highest level of flexibility; therefore, manufacturing system flexibility can be rationalized by finding out the best trade-off between productivity and flexibility. Manufacturing systems endowed with the right level of flexibility required by the production problems are named within the book Focused Flexibility Manufacturing Systems – FFMSs. A great deal of industrial sectors have to face this trade-off including, among the others, automotive, white goods, electrical and electronic goods. Also, the introduction of focused flexibility is not only important for system users but also for machine tool builders whose competitive advantage is based on the ability of customizing their system solutions on the basis of the needs of their customers. However, designing manufacturing systems that optimally satisfy the production requirements represents a very complex problem. Aspects ranging from manufacturing strategy to risk appraisal and management techniques, and from scenario analysis to system performance evaluation must be jointly taken into account considering the whole system life-cycle. Moreover, traditional system architectures do not always represent the most efficient solutions to properly face the new production context. Indeed, dedicated systems are not able to adapt to changes of the product characteristics while flexible systems often offer more flexibility than what is really needed, thus increasing investment and operating costs. The required level of system flexibility impacts on the architecture of the system and the explicit design of flexibility v

vi

Preface

can lead to new hybrid systems, i.e. automated integrated systems where the products can be processed both by general purpose machines and by dedicated machines. This is a key issue of FFMSs and results from the matching of flexibility and productivity that characterize Flexible Manufacturing Systems (FMSs) and Dedicated Manufacturing Systems (DMSs), respectively. Therefore the mission of the book is: ‘‘to define methodologies and tools to design production systems endowed with the right level of flexibility needed to face, during their life-cycle, the evolution of products, processes and market demand’’. The underlying idea is that flexibility has a cost therefore by using the right level required by the production problem on hand it is possible to find the optimal trade-off between flexibility and productivity. In spite of the relevance of the production system design topics, existing methodologies and tools do not provide an extensive support to the system designer since they typically deal with sub-problems of the whole design process. Indeed the wideness the topics related to system design can be seen as one of the reasons why this problem has not been sufficiently addressed until now. This work can be considered as an effort to provide an integrated framework to support the design of manufacturing systems that are able to cope with present and forecasted production problems in a cost-effective way. Herein, the main phases of the design activity are jointly structured, starting from the data collection and formalization of production information till the design and performance evaluation of the optimal system solution. Even if the proposed design approach can be applied to different production contexts and different system architectures, the authors have focused the analysis on the design of FFMSs. All the steps of the proposed approach are deeply investigated, and particular attention is paid to the methodologies adopted to face the different sub-problems (including: mathematical programming, stochastic programming, reverse kinematics and simulation techniques). By approaching the various aspects related to the design of system flexibility with formalized techniques and by applying the proposed framework to a set of real and realistic cases it is possible to have some figures of the advantages and costs related to flexibility. These figures even if related to the specific cases considered can provide interesting insights in the pros and cons of flexibility which can be exploited at managerial level. Most of the methodologies presented in this book have been developed within the two-year project ‘‘Methodologies and tools for the configuration of production systems with focused flexibility’’ funded by the Italian Ministry of University and Research (MUR) and coordinated by Politecnico di Milano – Dipartimento di Meccanica. The project itself is a joint effort of Politecnico di Milano, Politecnico di Torino, Universita` di Palermo, Universita` di Catania e Universita` del Salento. This book is also the result of continuous interactions with suppliers and users of manufacturing systems and in particular, among the others, with MCM S.p.A., Ferraioli & C. S.r.l. Nuova Meccanica S.p.A. The book structure follows the framework that has been developed to address the system design problem. This framework is both broad and

Preface

vii

detailed, since it pays attention to all the relevant levels of an organization that are involved in the system design activity (see Chap. 1). Moreover, the framework models both the point of view of the machine tool builder and the point of view of the system user. The work presented in this book links together different research fields by means of a shared information formalization (see Chap. 4). The research fields consist of: Manufacturing Strategy (see Chap. 5), Process Planning (see Chap. 6), System Design (see Chap. 7), Capacity Planning (see Chap. 8) and Performance Evaluation (see Chap. 9); moreover, the book gives a contribution to the formalization and rationalization of the concepts related to manufacturing system flexibility (see Chap. 3). The attention to industrial issues is confirmed by empirical studies (see Chap. 2) and real case analyses (see Chap. 10) which are presented within the book chapters to define the production domain where FFMSs are more profitable than traditional system architectures. Finally, some conclusions regarding new machine architectures are proposed to machine tool builders willing to provide innovative system solutions. As it can be seen from this brief preface, this book is only a step in a very complex and wide field, and it is an attempt, with limits and open issues, to have a joint understanding of system related issues that are frequently dealt separately. Indeed, the interactions among these issues deeply affects the resulting system flexibility and productivity; the comprehension and formalization of these interactions is the key to be able to design systems whose evolution is tuned on the evolution of the processes they implement and the product families they produce. Milano, Italy

Tullio Tolio

Contents

1

2

Designing Manufacturing Flexibility in Dynamic Production Contexts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Walter Terkaj, Tullio Tolio and Anna Valente

1

Flexibility in Manufacturing – An Empirical Case-Study Research. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marco Cantamessa and Carlo Capello

19

3

A Review on Manufacturing Flexibility . . . . . . . . . . . . . . . . . . . . . . . Walter Terkaj, Tullio Tolio and Anna Valente

41

4

Product-Process-System Information Formalization . . . . . . . . . . . . . Marcello Colledani, Walter Terkaj and Tullio Tolio

63

5

Manufacturing Strategy: Production Problem Analysis for Assessing Focused Flexibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manfredi Bruccoleri, Diego Lanza and Giovanni Perrone

6

7

8

Pallet Configuration for Approaching Mapping Requirements on Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Giovanni Celano, Antonio Costa, Sergio Fichera and Barbaro Santangelo Design of Focused Flexibility Manufacturing Systems (FFMSs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Walter Terkaj, Tullio Tolio and Anna Valente System Life-Cycle Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marco Cantamessa, Carlo Capello and Giuseppe Cordella

87

113

137

191

ix

x

Contents

9

System Performance Simulation and Analysis . . . . . . . . . . . . . . . . . . Antonio Grieco and Francesco Nucci

219

10

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manfredi Bruccoleri, Carlo Capello, Antonio Costa, Francesco Nucci, Walter Terkaj and Anna Valente

239

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

295

Contributors

Manfredi Bruccoleri Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita` degli Studi di Palermo, Palermo, Italy, e-mail: [email protected] Marco Cantamessa Dipartimento di Sistemi di Produzione ed Economia dell’Azienda, Politecnico di Torino, Torino, Italy, e-mail: [email protected] Carlo Capello Dipartimento di Sistemi di Produzione ed Economia dell’Azienda, Politecnico di Torino, Torino, Italy, e-mail: [email protected] Giovanni Celano Dipartimento di Ingegneria Industriale e Meccanica, Universita` degli Studi di Catania, Catania, Italy, e-mail: [email protected] Marcello Colledani Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy, e-mail: [email protected] Giuseppe Cordella Dipartimento di Sistemi di Produzione ed Economia dell’Azienda, Politecnico di Torino, Torino, Italy Antonio Costa Dipartimento di Ingegneria Industriale e Meccanica, Universita` degli Studi di Catania, Catania, Italy, e-mail: [email protected] Sergio Fichera Dipartimento di Ingegneria Industriale e Meccanica, Universita` degli Studi di Catania, Catania, Italy, e-mail: [email protected] Antonio Grieco Dipartimento di Ingegneria dell’Innovazione, Universita` degli Studi del Salento, Lecce, Italy, e-mail: [email protected] Diego Lanza Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita` degli Studi di Palermo, Palermo, Italy Francesco Nucci Dipartimento di Ingegneria dell’Innovazione, Universita` degli Studi del Salento, Lecce, Italy, e-mail: [email protected] xi

xii

Contributors

Giovanni Perrone Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita` degli Studi di Palermo, Palermo, Italy, e-mail: [email protected] Barbaro Santangelo Dipartimento di Ingegneria Industriale e Meccanica, Universita` degli Studi di Catania, Catania, Italy Walter Terkaj Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy, e-mail: [email protected] Tullio Tolio Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy, e-mail: [email protected] Anna Valente Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy, e-mail: [email protected]

Abbreviations

AMS BoM CV CAFD CAPP CNC DFD DSS DMS DCF FIFO FCI FMS FFMS GA MUR LCA MS MRD MHS NPV OMT OEM PC PM-FMS PM PSL ROA RMT RMS

Automated Manufacturing System Bill of Material Coefficient of Variation Computer Aided Fixture Design Computer Aided Process Planning Computer Numerical Control Data Flow Diagram Decision Support System Dedicated Manufacturing System Discounted Cash Flow First In First Out Fixture Capacity Index Flexible Manufacturing System Focused Flexibility Manufacturing System Genetic Algorithm Italian Ministry for University and Research Life-Cycle Analysis Manufacturing Strategy Mapping Requirements on Devices Material Handling System Net Present Value Object Modeling Technique Original Equipment Manufacturer Pallet Configuration Parallel Machine-FMS Performance Matrix Process Specification Language Real Options Analysis Reconfigurable Machine Tool Reconfigurable Manufacturing System

xiii

xiv

RTL SFC SME SPD STD SM TAD UML VRL-KCiP WS

Abbreviations

Rigid Transfer Lines Setup Face Configuration Small and Medium Enterprise Standard Placement Direction State Transition Diagram Switching Costs Matrix Tool Approach Direction Unified Modeling Language Virtual Research Lab for a Knowledge Community in Production Workingstep

Chapter 1

Designing Manufacturing Flexibility in Dynamic Production Contexts Walter Terkaj, Tullio Tolio and Anna Valente

Abstract Manufacturing Flexibility is seen as the main answer for surviving in markets characterized by frequent volume changes and evolutions of the technological requirements of products. However, the competitiveness of a firm can be strongly affected by capital intensive investments in system flexibility. This chapter presents an approach to design new manufacturing system architectures endowed with the right level of flexibility required by the specific production problem. These systems are named Focused Flexibility Manufacturing Systems (FFMSs). The key idea consists in tuning system flexibility on the production problem to cope with uncertainty related to the evolution of product demand. The significance of this topic and its potential impact on the industrial sector in the medium-long run is testified by the interest shown by companies making initial efforts in this field. Keywords Manufacturing system design activities Focused Flexibility Manufacturing Systems – FFMS

1.1 Market Uncertainty and Manufacturing Flexibility Manufacturing companies have to cope with the increasing pressure from global marketplace. In the last decade, the production of mechanical components to be assembled in final products produced in high volumes (e.g. cars, mopeds, industrial vehicles, etc.) has undergone deep changes due to the overall modifications in the way companies compete. In this situation the following trends can be observed:

Strategic components tend to be manufactured by the companies that produce the final products. For these strategic components firms define long

W. Terkaj (*) Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy e-mail: [email protected]

T. Tolio (ed.), Design of Flexible Production Systems, DOI 10.1007/978-3-540-85414-2_1, Ó Springer-Verlag Berlin Heidelberg 2009

1

2

W. Terkaj et al.

term plans. As a consequence, the technological characteristics, even if in continuous evolution, can be predicted with good accuracy. Less critical components tend to be externalized. In a context of continuous cost reduction, the producers of components try to obtain economies of scale by enlarging their size while specializing on some types of components. In both cases companies work on quite stable product categories produced in high volumes but, at the same time, they must cope with frequent product modifications and short product life-cycles. These drivers force the manufacturers to evaluate the ability to change their manufacturing systems and the penalty related to the change (Matta et al. 2005). This represents a complex issue in dynamic manufacturing contexts (Beach et al. 2000) like automotive, semiconductor, electronics and high tech markets, because the products are affected by frequent changes in volumes and technologies. It results that critical factors needed to be competitive are: short lead time, high quality of products, reactivity to market frequent changes and cost-effective production (Wiendahl et al. 2007). Obtaining optimality in each of the listed objectives can be difficult: frequently it happens that reaching optimal values for a single factor reduces the possibility of reaching optimal values for the other ones. This is the reason why companies often define production objectives as trade-offs among these critical factors (Chryssolouris 1996). Moreover, information related to production changes is often uncertain and the decision maker could be not able to precisely evaluate the probabilities associated with alternative production options. As a consequence, production system design activities can be highly complex and risky. In this context the acquisition of production capacity is particularly difficult (Matta and Semeraro 2005). Indeed, on the one hand dedicated manufacturing systems are not adequate to accommodate continuous product changes, even if they are competitive from the point of view of costs. On the other hand, flexible manufacturing systems have excessive flexibility which often remains unused and has a negative impact on costs. It results that manufacturing flexibility is not always a desirable characteristic of a system and in some cases it can jeopardize the profitability of the firm. Manufacturing flexibility has a strategic role for firms that want to compete in a reactive or a proactive way (Cantamessa and Capello 2007; Terkaj et al. 2008). In fact, the ability of designing production systems whose flexibility degree is customized on the present production problem and, at the same time, it takes into account future product evolutions, can lead to a competitive advantage. In the following section, some examples provided by recent literature will be presented to support the analysis of manufacturing flexibility. From the scientific perspective, focusing the flexibility of a production system on the specific needs represents a challenging problem. Indeed, the customization of system flexibility provides economic advantages in terms of

1 Designing Manufacturing Flexibility

3

system investment costs, but, on the other hand, tuning the flexibility on the production problem reduces some of the safety margins which allow decoupling the various phases of manufacturing system design. Therefore, manufacturing system flexibility must be rationalized and it is necessary to find out the best trade-off between productivity and flexibility by designing manufacturing systems endowed with the right level of flexibility required by the production problem (Ganzi and Tolio 2003). This new class of production systems is named Focused Flexibility Manufacturing Systems – FFMSs (Tolio and Valente 2006). The design of FFMS flexibility degree calls for a very careful risk appraisal: to reach this goal all the activities ranging from the definition of the manufacturing strategy to the configuration and reconfiguration of production systems must be redesigned and strictly integrated, thus highlighting the need of combining and harmonizing different types of knowledge which are all essential to obtain a competitive solution. The introduction of focused flexibility would be particularly important for machine tool builders whose competitive advantage is based on the ability of customizing their products on the basis of needs of their customers (Cantamessa et al. 2007). This does not necessarily mean to design new machine concepts; indeed, customizing the production flexibility could simply imply to combine existing resources in an appropriate way, answering to production requirements. For instance, new devices can be integrated with old machines and/or a production system can be characterized by flexible machines served by a rigid transport belt. In fact, the key issue is that focusing the whole system flexibility on the production problem does not exactly correspond to selecting customized devices but it represents just one design option. Industrial efforts with this aim have been addressed by Terkaj et al. (2008). To deeply understand how important is the strategic rationalization of flexibility, both from the academic and industrial perspectives, this chapter provides an extensive overview of this topic: a first analysis of the impact of production problem characteristics on the manufacturing flexibility degree required by production systems will be developed; afterwards, the new concept of Focused Flexibility Manufacturing Systems – FFMSs will be characterized in detail, highlighting the main differences with traditional production systems. Then, the FFMS design framework will be defined describing the main steps of the configuration phase; finally, the whole structure of the book will be illustrated.

1.2 The Impact of Production Problem Characteristics on Manufacturing System Flexibility The previous section has highlighted the importance of considering production characteristics during the manufacturing system design phase. If a firm does not take into account production requirements during the system design phase, the

4

W. Terkaj et al.

degree of manufacturing flexibility could result not appropriate for the problem. In this section, the relation between production requirements and corresponding system architectures are investigated with reference to the state of the art. It is rather frequent to find in literature the description of industrial situations where flexible systems have unsatisfactory performance (Koren et al. 1999; Landers 2000), cases where available flexibility remains unused (Sethi and Sethi 1990; Matta et al. 2001), or cases where the management perceives flexibility more as an undesirable complication than a potential advantage for the firm (Stecke 1985). Kulatilaka and Marks (1988) show that, at strategic level, flexibility can even be detrimental under certain circumstances particularly when uncertainty can be limited by means of proper agreements and contracts. Traditionally, rigid transfer lines (RTL) have been adopted for the production of a small family of part types required by the market in high volumes (Koren et al. 1998). RTLs are characterized by low scalability and therefore they are typically dimensioned on the maximum market demand that the firm forecasts to satisfy in the future (volume flexibility). As a consequence, in many situations RTLs do not operate at full capacity. On the other hand, flexible manufacturing systems (FMSs) and parallel machine – FMSs (PM-FMSs) have been adopted to produce a large variety of parts in small quantities (Hutchinson and Pflughoeft 1994; Grieco et al. 2002) and they are are conceived to react to most of the possible product changes. The investment to acquire an FMS is very high and it considerably affects the cost to produce a part; indeed, its flexibility may be too high and expensive for the needs of a producer of components for the automotive industry (Sethi and Sethi 1990). The high financial and organizational impact of FMSs has reduced their diffusion in the past; indeed, the initial outlay is so high that it severely strains the financial resources of the firms. Recent research efforts seem to individuate the concept of reconfigurability as the answer to the need for facing continuous changes in the production problems (Koren et al. 1999; Koren 2003, 2005, 2006). In fact, reconfigurability describes the operating ability of a production system or device to switch with minimal effort and delay to a particular family of work pieces or subassemblies through the addition or removal of functional elements (Wiendahl et al. 2007). In order to achieve exact flexibility in response to demand fluctuations, an RMS must be designed considering certain qualitative and quantitative enablers: modularity, integrability, customization, scalability, convertibility and diagnosability. However, despite the concept of reconfigurable resources is highly innovative it is quite difficult to be pursued considering available software and hardware technologies. Conversely, reconfigurability at system level can be obtained by using existing resources and production systems can be reconfigured every time the production problem requires it (Matta et al. 2008a). Unfortunately, this approach is not always cost-effective. Firstly, the reconfigurability option should be designed in order to accomplish its implementation when changes occur. Secondly, any reconfiguration along the system life-cycle


5

leads to face not only the installation costs but also operating costs related for instance to the ramp-up phase, typically characterized by machine malfunctioning and breakdowns, lost production and learning (Matta et al. 2008b).

1.3 Introduction to Focused Flexibility Manufacturing Systems – FFMSs The introduction of focused flexibility may represent an important means to rationalize the way flexibility is embedded in manufacturing systems. In particular, traditional production system architectures could not represent the most profitable solutions in case of mid to high production volumes of well identified product families in continuous evolution. Focused Flexibility Manufacturing Systems – FFMSs (Tolio and Valente 2006) represent a competitive answer to cope with the analyzed production context since they guarantee the optimal trade-off between productivity and flexibility. Moreover, the customization of system flexibility on specific production problems leads to the minimization of the system cost during its life-cycle. Indeed, the flexibility degree in FFMSs is related to their ability to cope with volume, mix and technological changes, and it must take into account both present and future changes. The required level of system flexibility impacts on the architecture of the system and the explicit design of flexibility often leads to hybrid systems (Matta et al. 2001), i.e. automated integrated systems in which parts can be processed by both general purpose and dedicated machines. This is a key issue of FFMSs and results from the matching of flexibility and productivity that characterize FMSs and Dedicated Manufacturing Systems (DMSs), respectively. FFMSs are hybrid systems, in the sense that they can be composed both of general purpose and dedicated resources. This innovative architecture derives from the consideration that system flexibility is related both to the flexibility of each single selected resource and to the interaction among the resources which compose the system. For instance, a flexible system can be composed of dedicated machines and highly flexible carriers. At first sight FFMSs could appear to be similar to Reconfigurable Manufacturing Systems (RMSs) (Koren et al. 1999; Ling et al. 1999; Landers 2000); the difference between these two classes of systems is in the timing of flexibility acquisition (Terkaj et al. 2008). Deciding about flexibility and reconfigurability means to consider two options. The first option deals with designing a dedicated system in which the reconfiguration option can be implemented in the future when production changes occur. This leads to design a system with the minimum level of flexibility required to cope with the present production problem. In this case FFMSs and RMSs have similar performance. The alternative option is to purchase more flexibility than the amount strictly required by the present production problem in order to avoid future system reconfigurations

6

W. Terkaj et al.

and ramp-ups. In this case, FFMSs have some extra-flexibility designed to cope with future production changes, i.e. a degree of flexibility tuned both on present and future production problems. The choice between designing the reconfigurability option or acquiring extraflexibility is strictly related to the investment costs analysis. For instance, if extraflexibility costs are lower than the discounted value of reconfigurability costs and ramp-up costs, then a flexible solution can be more profitable. Another fundamental issue to be considered is the industrial impact of the manufacturing flexibility rationalization. Even if current production contexts frequently present situations which would fit well with the FFMS philosophy, tradition and know-how of machine tool builders play a crucial role. Even if firms agree with the focused flexibility vision, nevertheless they often decide not to pay the risk and efforts related to the design of this new system architecture (Terkaj et al. 2008). The aspects which in the long run can convince the machine tool builders to provide innovative solutions to the customers depend on the profitability of FFMSs compared to FMSs and RMSs. At the moment, for different reasons and with more or less clear intents, many machine tool builders are trying to create new system architectures which to some extent represent first steps towards focusing the manufacturing flexibility. The introduction of focused flexibility would be particularly important for European machine tool builders whose competitive advantage is based on the ability of customizing their products on the basis of needs of their customers. To study the importance of the focused flexibility topic, an empirical research on the industrial viewpoint has been carried out. This analysis, presented in Chap. 2, gives a better understanding of the following key issues: (i) the value that firms assign to manufacturing flexibility; (ii) the approach adopted to tackle the demand of manufacturing flexibility; (iii) how the firms might react to the ‘‘focused flexibility’’ vision (Cantamessa and Capello 2007). Moreover, an example of industrial solutions related to focused flexibility will be presented in Chap. 3 (see Sect. 3.3.1).

1.4 Issues of the FFMS Design Phase The configuration of Focused Flexibility Manufacturing Systems requires the integration of various aspects related to product and process to support the design of the production system life-cycle. The solution of this problem is based on a deep investigation of very different topics ranging from manufacturing strategy to risk appraisal and management techniques, and from system performance evaluation to scenario analysis. The wideness of these topics can be seen as one of the reasons why this problem has not been sufficiently addressed so far (Cantamessa et al. 2007). The first key issue characterizing the FFMS design framework derives from the need for clarifying the relationship between the different types of flexibility


7

and the management and technical actions that must be followed to attain them. This lack of knowledge represents a critical problem for firm management since the definition of the proper course of actions to obtain and implement flexibility forms can be risky. Therefore, to fully understand the diffusion process of flexible automation and appreciate the problems it has encountered, it is necessary to investigate the choices made by companies. Thus, it is important to develop an empirical research on the adoption of flexible automation to study the value that firms assign to manufacturing flexibility. This analysis could contribute also to clarify how the firms not adopting FMSs have tackled the demand of manufacturing flexibility and how they might react to the ‘‘focused flexibility’’ approach. A way to cope with the issues related to manufacturing system design is to define more precisely and in quantitative terms the required forms of flexibility. The importance and innovation of this topic is highlighted by recent contributions aiming at precisely identifying the required flexibility profiles (Gupta and Buzacott 1989; Upton 1994; Koste and Malhotra 1999). However, even if the goal of these works was to define the impact of flexibility in quantitative terms, the obtained results tend to be qualitative. The research effort concerning this topic highlights an interesting consideration, i.e. the need for evaluating if the performance improvement justifies the extra-costs required by system flexibility. At the moment, this problem remains largely unsolved. Therefore, it results fundamental to find ways to express explicitly the flexibility needs of the firms starting from the analysis of the production problem. The key aspect of this approach is to be operative and pragmatic. Whereas, traditionally, existing design approaches start from the definition of the required flexibility levels, the framework presented in this chapter focuses the analysis on the production problem evaluation. Moreover, one has to consider that currently there is no standard methodology to define the characteristics of a production problem which takes into account the evolution over time: for this reason, it is necessary to define in a precise and formalized way the features of the problem, integrating models and visions coming from different fields. The design of FFMSs addresses another critical issue. In fact, by reducing the flexibility levels of a system, the ability to cope with production variability is decreased. In this sense, the availability of flexibility in excess can sometimes prevent from some types of risk. As a consequence, in the definition of the right level of flexibility a key role is played by methodologies and tools to design the system flexibility considering the risks connected with the choice. The problem is complex because after that the required flexibility profiles have been defined, it is necessary to devise methodologies to design a system able to provide those levels of flexibility. This requires, on one side, the evaluation of the characteristics of different system architectures and of different machines and, on the other side, the correct matching between the required flexibility and the implemented system.

8

W. Terkaj et al.

1.5 The Design of FFMSs The previous section has highlighted the complexity of the FFMS design problem by focusing the analysis on the key issues which should be faced. This analysis represents the basis on which the FFMS design framework has been developed. However, despite herein the attention is centered on FFMSs, the proposed framework has more general applicability. Indeed, the provided system design framework starts from the production context analysis and implicitly defines the system flexibility requirements without considering existing flexibility taxonomies and classifications. Moreover, another key issue of the FFMSs design framework consists of considering at the same time two main actors involved in the system configuration problem: the System User and the Machine Tool Builder. The interactions between the actors are represented with a UML Activity Diagram in Fig. 1.1. The system user starts the information flow

Fig. 1.1 System user and machine tool builder interaction


9

sending a bid inquiry to one or more machine tool builders. Each machine tool builder carries out a preliminary assessment of bidding opportunity. If the potential order is interesting, then the machine tool builder designs a manufacturing system which satisfies the production requirements related to the types of product and the demand volumes defined by the client. System configuration requires as input a technological analysis of the production problem and this activity is usually executed by machine tool builders. When the system user receives the set of bids, it is possible to evaluate if the investment is cost effective. If it is effective, then an order is submitted to the winning machine tool builder who can start the production of the system. Since there are two types of actor, the problem of system design and offer generation can be addressed according to the system user perspective or to the machine tool builder one. While in the former case the problem has been studied both technologically and economically, in the latter case there are few specific studies and mainly works addressing the problem of bid generation for a generic seller, without dealing with technological aspects. The different knowledge and objective of the two actors in the problem can lead to designing manufacturing systems which are suboptimal for the needs of the user; this can happen when the user is wrong about his requirements forecasts, or because the machine tool builder has designed a system with excessive flexibility to cope with missing information from the client or because the machine tool builder succeeded in selling an oversized system. In the following section the system machine tool builder and system user perspectives will be illustrated.

1.5.1 Description of the FFMS Design Approach As previously stated, a fundamental step of the FFMS design framework consists of a deep understanding of the information flow that characterizes the whole process. The definition of the information flow at industrial level is necessary to develop a unique standard conceptual reference framework for the formalization of data concerning products, processes and production systems and their relations, because these data play a key role within a system configuration architecture (Cantamessa et al. 2007). An IDEF0 diagram has been developed to represent the system design activity (Fig. 1.2). The input of the system design activity consists of information about present and potential products of the system user demand, physical devices that the machine tool builder can select, system architectures (i.e. type of system that can be implemented, such as transfer lines, flexible manufacturing systems) and investment and operating costs. The first output of the FFMS design activity is the assessment of the applicability of focused flexibility to address the production problem; if focused flexibility is applicable, then it is necessary to define the system specifications (i.e. set of resources composing the system) and the timing of system

10

W. Terkaj et al. Product and production system lifecycle formalization Database of actual and potential products

Design constraints

Design goals

Manufacturing strategy Focused Flexibility non applicable

Meet production requirements

System specifications Timing of system acquisition

Database of physical devices

System Costs

System architectures

Design Systems with Focused Flexibility

Costs

Focused Flexibility rules Reverse kinematic methods

Economical advantages of focused flexibility

A0

Cluster analysis

Option theory

Scenario System generation design tools methodologies

Analytical tools

DCF tools

Multicriteria analysis

Scenario analysis

Simulation Analysis of Stochastic technological programming requirements

Combinational Linear optimization programming

Fig. 1.2 IDEF0 diagram

acquisition, considering both configuration and reconfigurations. A cost analysis allows also evaluating the economic advantages of focused flexibility. The FFMS design activity must respect a set of constraints defining the manufacturing strategy, the production requirements and the design goals. Moreover, it is necessary to adopt the data formalization describing product and production system life-cycles. This formalization is presented in Chap. 4 and represents the base on which methodologies and tools to design production systems with focused flexibility can be developed. Methodologies and tools are endowed with a set of mechanisms ranging from reverse kinematics methods to simulation as well as from scenario generation to stochastic programming. The FFMS design architecture provides a general approach to implement the right degree of flexibility and it allows to study how different aspects and decisions taken in a firm impact on each other. The main characteristic consists in to the development of links among different research fields, such as Manufacturing Strategy, Process Plan, System Design, Capacity Planning and Performance Evaluation. The whole FFMS design approach defined in Fig. 1.2 can be further detailed with the IDEF0 diagram shown in Fig. 1.3. The system design problem is handled by both the system user and the machine tool builder. In particular, the activity ‘‘Plan System Capacity’’ is associated with the system user, while ‘‘Design Systems’’ to the machine tool builder. Within ‘‘Plan System Capacity’’ activity, the system user identifies the production contexts where focusing the system flexibility can be a good option by developing a strategic analysis (Activity A11 in Fig. 1.4). When alternative


11 Meet Design Design goals constraints production requirements C2 C3 C4

Manufacturing Product and production strategy system lifecycle formalization C5 C1 Database of actual and potential products I1

Focused Flexibility non applicable

Characteristics of the parts

O1 Timing of system acquisition

Plan System Capacity Budget constraints

O3 Features to be produced

M6 Option theory

M13 Combinatorial optimization

M3 Scenario generation tools

I2

I3

Production volumes

Evolution scenarios

system specifications O2

Design Systems

Database of physical devices

Unfeasible systems

A2

System architectures

Costs I4

System Costs O4 O5

Compare system Performance A3

M1 Reverse kinematic methods M11 Analysis of technological requirements

M4

M2

M9

M15

M5

M7

M12

M10

M14

Economical advantages of focused flexibility M8

Focused Stochastic System Analytical Linear Cluster Multicriteria DCF Scenario Simulation Flexibility programming programming design analysis tools analysis tools analysis rules methodologies

Fig. 1.3 IDEF0 diagram – FFMS Design Activities

Manufacturing strategy C1

Database of actual and potential products I1

Specify Manufacturing Strategy A11

Meet Design production Unfeasible Design goals constraints requirements systems C3 C4 C5 C7

M2 Scenario generation tools

I2

Focused Flexibility non applicable O1 Production volumes O4 Budget constraints O3 Characteristics of the parts O5 Features to be produced O7 Evolution scenarios O6

System Product and production Costs system lifecycle formalization C6 C2

Timing of system acquisition

Plan System Lifecycle

System specifications

O2 A12

M3 Option theory

M4 Multicriteria analysis

Fig. 1.4 IDEF0 diagram – A1 Plan System Capacity

M1 Combinatorial optimization

M5 DCF tools

12

I5 I1 I2 I3

W. Terkaj et al.

Database of physical devices Production volumes Characteristic of the parts Evolution scenarios Features to be produced

I4

Product and production system lifecycle formalization C2

Meet Budget Design Design Unfeasible production Constraints goals constraints systems requirements C1 C3 C4 C5 C6

Map Requirements on Devices

A21

M1 M2 Analysis of Reverse technological kinematic requirements methods

Mapping between features and feasible devices

Pallet configuration

System specifications

Design Systems

O1 A22

I6 I7

System architectures Costs

M3 M5 Cluster Stochastic analysis programming

M7 M4 M6 M8 M9 System Focused Linear Analytical DCF design Flexibility rules programming tools tools methodologies

Fig. 1.5 IDEF0 diagram – A2 Design Systems

system configurations have been received and analyzed, the system user defines the timing of acquisition of the resources, thus planning the system life-cycle (Activity A12 in Fig. 1.4). Once the system user has carried out his strategic analysis and defined the system requirements, the machine tool builder starts studying the possible matching among production requirements and selectable resource devices (Activity A21 in Fig. 1.5). The results of this analysis are used to design alternative system configurations in terms of number and type of resources (Activity A22 in Fig. 1.5). Indeed, it is possible to design both systems with focused flexibility and systems whose architecture is characterized by the highest flexibility level, i.e. a Flexible Manufacturing System. This particular configuration will be used to develop a comparative analysis between FFMS and FMS aiming at studying the profitability of the FFMS solution (see Chaps. 7 and 10). Finally, in order to select the most profitable solution for the analyzed production problem, the alternative system configurations need to be evaluated in term of system performance. This analysis regards the evaluation of the FFMS and FMS performance and is supported by simulation technique (Activity A3 ‘‘Compare System Performance’’).

1.6 FFMS Design Activities This section provides a detailed description of the design activities previously introduced, following the information flow represented in Figs. 1.3, 1.4 and 1.5.


13

1.6.1 Specification of Manufacturing Strategy The system design process starts from the system user with a strategic analysis which aims at finding out the production contexts where focused flexibility is a winning decision (Bruccoleri et al. 2005). Focused flexibility can be seen as a competitive lever and its specifications should be elaborated within the manufacturing strategy; an approach has been developed to translate strategic decisions into competitive priorities and strategic drivers. This approach has been implemented in an innovative theoretical framework based on the definition of a business strategy and of a manufacturing strategy, together with their impacts on the specifications for the manufacturing system that will be implemented. Manufacturing strategy is deeply related to the ‘‘Test Case Generation’’ problem. Indeed, to verify the viability of the focused flexibility approach it is necessary to test it in realistic situations which must be devised in coherence with the adopted strategy. A high level strategy defines the position of the firm in the whole market and this decision reduces the domain (and the uncertainties) of possible production problems that the firm is interested in facing. Strategic considerations also lead to the definition of the type and life-cycle of the part family to be addressed. This definition consists of a set of data regarding technological information, part mix and production volumes. A real production context of potential application of the Focused Flexibility concept is typically characterized by:

products evolving in accordance with their life-cycle; product families evolving over time; the product versions can be demanded together or they can be substitutive;

demand correlation among the product families and among the product versions: positive correlation in the case of complementary products and negative correlation in substitutive products. Moreover, the product (both family and version) life-cycle must respect the growth-maturity-decline shape. The intrinsic variability of the production problem can lead to different evolutions of demand for each product family and version. An interesting evaluation concerns how the system design process is influenced by the variability of the demand and how to model this type of uncertainty. Since a production problem resulting from the combination of many products can be pretty hard to manage in an evolutionary perspective, the Scenario Tree representation is adopted to simplify the problem representation. Each node of the tree is characterized by a realization probability and it represents a possible production problem in a defined time stage. A wider presentation of this kind of approach can be found in the paper by Ahmed et al. (2003), while a detailed description of the developed approach will be presented in Chap. 5.

14

W. Terkaj et al.

1.6.2 Mapping of Requirements on Devices The collection and formalization of present and forecasted information concerning the production problems represent a key issue for the design problem. In particular, the whole set of data is used by the system user to share information about the part family with his potential system suppliers together with the bid inquiry. After the machine tool builder has collected the necessary information, the technological analysis of the production problem can start. This analysis aims at defining alternative process plans to produce the workpieces and consists of the elaboration of a mapping among the part type and the selectable manufacturing resources (see Chap. 6). This implies to match each feature with an operation or a sequence of operations, taking in considerations the feasible setups. Proper models have been developed and software modules have been implemented to realize a technological link between products and machines by using the information associated with each product (volumes to be manufactured, technological and geometric specifications). The developed modules take information concerning workpieces, features, machining operations and resources (machines and physical pallets) as input. This information needs to be elaborated in order to find the matching between machines and operations and machines and physical pallets. In particular, setups of the workpieces and the rapid movement times for each setup are evaluated according to the machine performance. A further step consists of configuring the pallet and in turn assigning workpiece setups to pallets in order to develop a set of alternative process plans, i.e. pallet sequences to process the workpieces of the various part families.

1.6.3 Design of System Configurations Strategic and technological analyses provide the information required to apply configuration methods for focused flexibility manufacturing systems (see Chap. 7). Depending on how the production problem variability, i.e. the evolution scenarios, has been modeled, different configurations methods can developed and implemented: for instance, in the deterministic methods it is assumed to have the perfect information about future whereas in the stochastic models forecasts are assumed to be affected by uncertainty. Moreover, in stochastic models the production problem scheduling during the observed time horizon could determine two- or multi-stage approaches. To clarify the differences just introduced, three different system design models are listed:

in the deterministic approach (Tolio and Valente 2006) it is supposed that the evolution scenarios are not characterized by a time sequence;

in the two stage stochastic approach (Tolio and Valente 2007; Tolio and Valente 2008) the temporal sequence of the scenarios and their realization probability are considered;


15

in the multi-stage stochastic approach the sequence of system configurations and possible reconfigurations are modeled, starting from a more complex scenario tree formulation. All these methods aim at the minimization of the investment costs and therefore the solutions are optimal from the point of view of the system user but they may not be the best from the point of view of the machine tool builder. Indeed, the machine tool builder aims at maximizing his expected profit and not at minimizing the system cost, even if the two problems are strongly related. A new approach for system configuration considering the point of view of the machine tool builder has been preliminarily investigated by Terkaj and Tolio (2007); the solution provided by such an approach is the offer for the potential client of the machine tool builder, i.e. the system user. This offer consists both of the technological solution (system configuration) and the economic conditions (price, due date).

1.6.4 Planning System Life-Cycle In the previous sub-section different approaches to design production systems have been described. The machine tool builder obtains as output a set of optimal and sub-optimal system configurations and reconfigurations. However, these solutions need to be evaluated from the system user in order to carry out the planning of the system life-cycle. This step requires an analysis of the technological and economic characteristics of the different available system solutions, in order to carry out an economic and financial appraisal from the system user perspective (Cantamessa and Valentini 2000). A model has been developed for calculating the economic value of the flexibility offered by the different machine tool builders; this model is aimed at supporting decisions on the type and timing of system configurations to be acquired and – coherently with the ‘‘focused flexibility’’ concept – its degree of flexibility. The main concept being used is Real Options Analysis (ROA) (Copeland and Antikarov 2001), which is known to provide a more precise value of flexibility than what classical capital budgeting practices would generate. ROA has already been proposed in literature (Bengtsson 2001; Amico et al. 2007) for evaluating manufacturing flexibility in general, but its application within the context of ‘‘focused flexibility’’ solutions is innovative. The global structure of the system life-cycle planning approach is composed of two main modules, as it will be deeply illustrated in Chap. 8. The first module takes as input the set of scenario nodes and system configurations and evaluates the performance of each configuration in the different scenario nodes. These values become the input of the second module which provides as output the timing of system configuration over the planning horizon. These two modules give as output two production system configurations, i.e. a Flexible Manufacturing System and a Focused Flexibility Manufacturing System, both characterized by the minimum system total cost.

16

W. Terkaj et al.

1.6.5 Comparison of System Performance In order to evaluate the real benefits coming from focusing the production system flexibility, the possible system configurations and, above all, the decisions taken by the system user need to be analyzed. The evaluation of the system performance, addressed in Chap. 9, is carried out applying a set of simulation tools (Grieco et al. 2002, 2003). The innovative aspect relies on the chance to test the different system solutions when facing changeable production problems. In particular, it requires the development of tailored methods and tools for production planning in a focused flexibility system both at loading and scheduling level.

1.7 Introduction to the Structure of the Book The book framework follows the architecture which has been developed to address the FFMS Design problem. The following chapters will analyze the production system flexibility problem both from the industrial point of view (see Chap. 2) and from the academic point of view (see Chap. 3). The methodologies to design systems with focused flexibility will be described starting with the formulation of the general data formalization model (see Chap. 4) which enables the communication among all the design modules. Chapters 5, 6, 7, 8 and 9 will present the methodologies and tools related to the five different steps of the design architecture (see Sect. 1.5). All the steps of the architecture are deeply studied, developing methods and tools to address each sub-problem. Particular attention is paid to the methodologies adopted to face the different sub-problems: mathematical programming, stochastic programming, simulation techniques and inverse kinematics have been adopted. Finally, industrial cases and relevant test results will be presented in Chap. 10. Acknowledgments The research has been partially funded by the MUR (Italian Ministry for University and Research) under the PRIN project ‘‘Methodologies and tools for the configuration of production systems with focused flexibility’’, contract code: 2005097985.

References Ahmed S, King A, Parija G (2003) A multi-stage stochastic integer programming approach for capacity expansion under uncertainty. J Glob Optim 26:3–24 Anglani A, Grieco A, Pacella M, Tolio T (2002) Object-oriented modeling and simulation of flexible manufacturing systems: a rule-based procedure. Simul Model Prac Theory 10(3):209–234 Amico M, Asl F, Pasek Z, Perrone G (2007) Real options: an application to RMS investment evaluation. In Dashchenko AI (ed) Reconfigurable manufacturing systems and transformable factories. Springer, New York


17

Beach R, Muhlemann AP, Price DHR, Paterson A, Sharp JA (2000) A review of manufacturing flexibility. Eur J Oper Res 122:41–57 Bengtsson J (2001) Manufacturing flexibility and real options. A review. Int J Prod Econ 74:213–224 Bruccoleri M, Lo Nigro G, Noto La Diega S, Perrone G, Renna P (2005) Strategic planning in advanced manufacturing systems: a decision support system. In Semeraro Q, Matta A (eds) Design of advanced manufacturing systems models for capacity planning in advanced manufacturing systems. Springer, New York Cantamessa M, Capello C (2007) Flexibility in manufacturing – outlining an empiricallybased method for its valuation. 8th AITeM Conference, Montecatini Terme, 10–12 September, 2007 Cantamessa M, Valentini C (2000) Planning and managing manufacturing capacity when demand is subject to diffusion effects. Int J Prod Econ 66:227–240 Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceedings of the 4th international conference on digital enterprise technology, Bath, UK, 19–21 September, pp 627–636 Copeland T, Antikarov V (2001) Real options: a practitioners’ guide. Texere, New York Chryssolouris G (1996) Flexibility and its measurement. Ann CIRP 45(2):581–587 Ganzi E, Tolio T (2003) Configuration and Re-Configuration of Manufacturing Systems with Focused Flexibility. 6th Convegno A.I.Te.M., Gaeta, Sept 2003, pp 1–10 Grieco A, Nucci F, Anglani A (2003) Representation of fuzzy time variables in discrete event simulation. Integr Computer-Aided Eng 10(4):305–318 Gupta D, Buzacott JA (1989) A framework for understanding flexibility of manufacturing systems. J Manuf Syst 8(2):89–97 Hutchinson GK, Pflughoeft KA (1994) Flexible process plan: their value in flexible automation systems. Int J Prod Res 32(3):707–719 IDEF0, www.idef.com/pdf/idef0.pdf Koren Y (2003) ERC/CIRP survey on flexible manufacturing systems. Working Group A/M/O meeting, Paris, 01.2003 Koren Y (2005) Reconfigurable manufacturing and beyond (Keynote Paper), CIRP 3rd International Conference on Reconfigurable Manufacturing, Ann Arbor, Michigan, 11–12 May 2005 Koren Y (2006) General RMS characteristics. Comparison with dedicated and flexible systems. In: Dashchenko AI (2006) Reconfigurable manufacturing systems and transformable factories, Springer Verlag, Berlin/Heidelberg, pp 27–46 Koren Y, Hu SJ, Weber TW (1998) Impact of manufacturing system configuration on performance. Ann CIRP 47(1):369–372 Koren Y, Heisel U, Jovane F, Moriwaki T, Pritschow G, Ulsoy G, Van Brussel H (1999) Reconfigurable manufacturing systems. Ann CIRP 48(2): 527–540 Koste L, Malhotra MK (1999) A theoretical framework for analyzing the dimensions of manufacturing flexibility. J Oper Manag 18(1):75–93 Kulatilaka N, Marks SG (1988) The strategic value of flexibility: reducing the ability to compromise. Am Econ Rev 78(3):574–580 Landers RG (2000) A new paradigm in machine tools: Reconfigurable machine tools. Japan-USA symposium on flexible automation, Ann Arbor, Michigan, 2000 Ling C, Spicer P, Son SY, Hart J, Yip-Hoi D (1999) An example demonstrating system level reconfigurability for RMS. ERC/RMS Technical Report 29 Matta A, Semeraro Q (2005) Design advanced manufacturing systems – models for capacity planning in advanced manufacturing systems. Springer, New York, ISBN 1-4020-2930-6, pp 1–267 Matta A, Semeraro Q, Tolio T (2005) A framework for long term capacity decisions in AMSs. In: Matta A, Semeraro Q (ed) Design advanced manufacturing systems – models for capacity planning in advanced manufacturing systems. Springer, New York

18

W. Terkaj et al.

Matta A, Tomasella M, Valente A (2008b) Impact of ramp-up on the optimal capacity-related reconfiguration policy. Int J Flex Manuf Syst 19(3):173–194 Matta A, Tolio T, Karaesmen F, Dallery Y (2001) An integrated approach for the configuration of automated manufacturing systems. Robotics Comput Integr Manuf 17:19–26 Matta A, Tomasella M, Clerici M, Sacconi S (2008a) Optimal reconfiguration policy to react to product changes. Int J Prod Res 46(10): 2651–2673 Sethi AK, Sethi SP (1990) Flexibility in manufacturing: a survey. Int J Flex Manuf Syst 2:289–328 Stecke KE (1985) Design, planning, scheduling and control problem of flexible manufacturing systems. Ann Oper Res 3:1–13 Terkaj W, Tolio T (2007) An approach to production system design considering the utility of the machine tool builder. 40th CIRP International Seminar on Manufacturing Systems, Liverpool, UK, 30 May–1 June 2007 Tolio T, Valente A (2006) An approach to design the flexibility degree in flexible manufacturing system. Proceedings of flexible automation & intelligent manufacturing conference, Limerick, Ireland, June 25–27, 2006, pp 1229–1236 Tolio T, Valente A (2007) A stochastic approach to design the flexibility degree in manufacturing systems with focused flexibility. Proceedings of the 4th international conference on digital enterprise technology, Bath, UK, 19–21 September, pp 380–390 Tolio T, Valente A (2008) A stochastic programming approach to design the production system flexibility considering the evolution of the part families. To appear in Int J Manuf Technol Manag – special issue on reconfigurable manufacturing systems Terkaj W, Tolio T, Valente A (2008) Focused flexibility in production systems. In: ElMaraghy H (ed) Changeable and reconfigurable manufacturing systems. Springer, New York Upton DM (1994) The management of manufacturing flexibility. Calif Manag Rev 36(2):72–89 Wiendahl H-P, ElMaraghy HA, Nyhuis P, Za¨h MF, Wiendahl H-H, Duffie N, Brieke M (2007) Changeable manufacturing – classification, design and operation. Ann CIRP 56(2):783–809

Chapter 2

Flexibility in Manufacturing – An Empirical Case-Study Research Marco Cantamessa and Carlo Capello

Abstract Since the last two decades, manufacturing firms are facing an increasingly risky environment because of product differentiation, high demand variability and shortening of product life-cycles. Because of these trends, firms need to innovate their manufacturing resources in order to promptly respond to new requests coming from markets. Traditionally, this meant moving from rigid production lines to Flexible Manufacturing Systems (FMS). However, literature and empirical evidence prove that firms have not really located themselves on one of these two opposing manufacturing plant strategies. Rather, they have filled up the vast ‘‘gray area’’ in the middle. Their attempts have been aimed at developing manufacturing system solutions allowing them to precisely supply their markets’ needs, and consequently paying for the system flexibility they really need. Because of this, the concept of manufacturing flexibility has to be revised and extended in order to include these solutions involving a ‘‘customized’’ or ‘‘focused’’ architectural flexibility. The current chapter shows the results from the case study research that empirically supports and casts insights in this trend. Based on these findings, a conceptual framework is proposed to interpret how firms perceive the strategic meaning of and realize flexibility. Keywords Manufacturing flexibility Empirical research Real options

2.1 Introduction As a wide body of literature proves (De Toni and Tonchia 1998), manufacturing flexibility – both at process and product level – has been an important topic in manufacturing since around the Eighties. Manufacturing flexibility allows firms to respond customers’ demand by dealing with market uncertainties. Due to C. Capello (*) Dipartimento di Sistemi di Produzione ed Economia dell’Azienda, Politecnico di Torino, Torino, Italy e-mail: [email protected]


19

20

M. Cantamessa and C. Capello

increasing variability of demand, product variety and shorter product life-cycles, firms need to be flexible enough to produce the components requested by customers with short lead times (Boyer and Leong 1996). These needs have led machine tool builders to develop solutions characterized by a very high operational flexibility, such as Flexible Manufacturing Systems (FMS). However, according to literature, these systems with general purpose machines have not diffused as expected (Handfield and Pagell 1995). Firms are generally quite reluctant to move towards FMSs because they represent decisions of high financial and organizational impact. The initial outlay is so high that it often severely strains firms’ financial resources, while the flexibility allowed by FMSs is often oversized with respect to real needs (Tolio and Valente 2006). Moreover, complexity of managing operations in an FMS is also quite high (Matta et al 2000). Empirical evidence confirms that companies need flexibility, because of the requirements coming from markets, but that this can be achieved through different approaches. Viable alternatives are, for instance, combinatorial flexibility deriving from the assembly of standardized components, outsourcing of critical activities, and ‘‘focused flexibility’’ system configurations (Tolio and Valente 2007). The last alternative represents a relatively new concept, which is based on system configurations that aim to meet users’ flexibility requirements precisely. Such solutions can be more flexible than conventional ‘‘rigid’’ systems but – at the same time – they do not exhibit all the expensive flexibility of FMSs, which is often left unused (Tolio and Valente 2006). Chapter 1 of this book defines the FFMS concept and the way with which flexibility is interpreted in this new kind of manufacturing system. This chapter has the objective of providing an empirical foundation to the FFMS concept, and showing the degree with which elements of this paradigm can be actually found in current industrial practice. The chapter is structured in two main sections. The first section presents the results of the empirical case-study research, whose objective was to understand the way with which flexibility is perceived and managed by both manufacturing system users and machine tool builders. For this purpose, it has been selected a panel of companies to interview, including both system users and machine tool builders. In order to gain a wider perspective, the research was not limited to metalworking, but also investigated other industries. Therefore, in this chapter the term ‘‘machine tool builder’’ will be replaced by the more general term ‘‘system producer’’. Case studies let to capture an interesting set of approaches to flexibility used by the interviewed firms, from both system vendors’ and system users’ standpoints. The second section covers a proposal for a conceptual model that can be used for reading and understanding the findings of empirical research. The chapter takes the concepts of manufacturing flexibility, focused flexibility and related machine solutions for granted, as a thorough discussion and related literature are already proposed in Chap. 3 of the book. This chapter is structured as follows: Section 2.2 introduces the empirical research methodology, the interviewed company panel and the results. Next, Sect. 2.3 develops a conceptual framework to read the empirical results and

2 Flexibility in Manufacturing

21

interpret the way companies make flexibility – in terms of both positive and negative feedback. In the end, Sect. 2.4 synthesizes main findings while Appendixes integrate the chapter with some matrixes summarizing information from interviews conducted for empirical research.

2.2 Empirical Research 2.2.1 Methodology The empirical research has been conducted to reach three main objectives: find out (a) how firms manage and value manufacturing flexibility, (b) which manufacturing system solutions they tend to adopt and (c) how they react to the ‘‘focused flexibility’’ approach. The research has been conducted through ‘‘in person’’ interviews with a set of pre-selected companies. The sample is composed of twelve midsize Italian firms – that would be the more appropriate target for ‘‘Focused Flexibility’’ adoption – with a consolidated presence on the Italian and international markets (see Appendix 1 for the list of companies. Company names are omitted according to non-disclosure agreements). The main investigated industry is metalworking, however the research spanned other industries where flexible manufacturing machineries are used including textile, wine bottling and woodworking to gain a wider perspective. For each industry, the research included system users and vendors to gain insight into the value chain and have a deeper understanding of the system acquisition process. The intent of the research has been to consider each firm just into the related industry value chain, rather than as a representative of a wider population – i.e. the overall industry. The research methodology is based on commonly accepted standards for qualitative empirical research (Yin 1994). Interviews and case studies were iterative, interpretative and comparative (Lee 1996) as shown in Fig. 2.1. The iterative approach (i.e. it follows the same process per each industry) is used to investigate how flexibility is managed (i.e. how companies understand their needs, select a degree of flexibility and evaluate investments). The use of a common interview framework allows to collect the same kind of data and to make comparisons easier. The interpretative approach allows to find out and

Fig. 2.1 Methodology flow chart

22


codify elements which were latent in the interviews. Finally, comparisons allow to lead the discussion from an aggregate and more general perspective. Interviews have been conducted to capture information from different sources by each company: Chief Executive Officers, Manager Directors, Chief Financial Officers, and Production Managers were the main interlocutors for the primary research. Interviews have been semi-structured on three sections. For system producers, three sections have been investigated: (a) the firm’s organization, strategy and business context, (b) approaches used to handle clients’ flexibility needs and (c) techniques to evaluate flexibility. For system users, the section (b) of the interview framework has been modified to include the required kinds of flexibility and choices for manufacturing systems. Interviews were recorded and transcribed in a case study report. Finally, case studies were integrated in a final document to summarize and compare results (see Appendix 2 for a comparison matrix of main highlights from interviews). The complete research material (details on companies and industries, transcripts of case study interviews, etc.) is available from authors.

2.2.2 Interviewed Companies The panel of companies interviewed is heterogeneous. It includes companies from 20 up to several hundred employed people. Some companies are privately owned and family-run, others are part of larger international corporations. All of them are profitable and well established on the domestic market while only larger firms serve international markets. Some operate on large markets and are experiencing growth, others serve small niches with stable revenues. All the interviewed companies produce or use some kind of manufacturing systems and look at manufacturing flexibility as a topical and critical matter (see Appendix 3 to know which kind of flexibility each company dealt with).

2.2.3 Results from Empirical Research 2.2.3.1 Business Context The business context is quite different for the various companies interviewed. Metalworking companies are mainly suppliers for automotive and aerospace industries. Despite obvious differences, they share some common features, such as an increasing product mix, decreasing product life-cycles, the need to expand to foreign markets, and the competition played especially on costs and manufacturing lead-time. In woodworking the empirical research covered plywood production. This industry is quite fragmented, whereas machinery suppliers are few and large. Plywood manufacturers face high uncertainty in matching a highly variable final product demand with scarce raw-material availability. In textile the research covered wool manufacturing, whose process is composed of


23

several phases. Weavers are vertically integrated, while system producers are focused on making machines dedicated to specific manufacturing steps. This industry has suffered over last years because of aggressive competition from Far East producers, downturns in European economies and the introduction of new materials. System producers face a decreasing local demand and try to extend their businesses to new markets, offering their products at prices that barely cover costs without being able to make customers perceive and pay the innovation contents they offer. Winemaking industry has a high degree of vertical integration, going from grape growing to bottling (and sometimes even distributing). The research was focused on bottle filling and labeling. In the case of high-quality producers, the volume and product mix uncertainties does not look very high because of an increasing demand. Moreover, the major source of uncertainty is from the range of bottle types and label materials and dimensions, and not from the type of liquid to be bottled (still or sparkling wine), since producers generally are quite specialized. 2.2.3.2 Manufacturing Systems Empirical evidence confirmed some expectations about how firms handle investment decisions in new production systems. The interviews revealed that metalworking firms operating in high-volume production tend to exploit existing machinery as much as possible and invest in new resources when it becomes absolutely necessary. Firms operating in niches invest in product-specific machineries in order to achieve the best performance possible. Finally, players operating on a wider and less structured market (typically job shop subcontractors) tend to acquire flexible machines which allow them to cope with a broad, even if not planned, variety of components. However, no companies in the sample implemented fully fledged FMSs: major reasons seemed to be the high acquisition costs and the concern that they were not to able to pay back the investment. The two system producers come from the two ends of the flexibility spectrum: one traditionally builds transfer lines and the other FMSs. However, they are both moving to systems with an ‘‘intermediate’’ degree of flexibility. In the case of the transfer line manufacturer, this is especially due to the need for ‘‘manufacturing systems enabling our customers to cover a broader product range and to reduce downtimes when ramping up new products’’. Their systems are increasingly shifting towards mixed-model lines (i.e. capable to produce different models at the same time), with modular production units that can be easily redeployed at the time of introduction of new products, and with a greater use of CNC machining centers (which – due to the availability of fast linear motors – nowadays allow to achieve production volumes that are comparable to what can be obtained with specialized machinery). Conversely, the machine tool builder manufacturing FMSs is reducing the degree of flexibility and offering what can be termed ‘‘Focused Flexibility Manufacturing Systems’’ (FFMS). The company stated that ‘‘our customers are no longer willing to pay for a flexibility which they know will remain unused. They

24


ask us to tailor new machines on their needs and sell them exactly what they want and nothing more’’. Focused flexibility generally means a lower flexibility degree on main components of a manufacturing system. Basically, with respect to an FMS, the processing unit has fixed equipments, the tool stock is smaller and less various, and the load-unload process is automatically or robotically managed. Flexible automation is still present in FFMSs, especially in the field of materials handling, but in a smaller quantity. Machines are therefore custom-designed to each customer product portfolio and require some amount of reconfiguration when introducing new products. In plywood manufacturing uncertainty on raw materials and final products is mainly tackled through component flexibility (in this case, this means that the thin veneers peeled from logs come in many different thicknesses and are then combined in a high variety of panel structures). This requires a highly automated and flexible peeling lathe, while the assembly of panels is mainly left to a traditional process with relatively high labor content. The producer of plywood manufacturing systems stated that ‘‘we are able to design and build very flexible lines, but our customers still are quite specialized, and therefore they are not willing to pay for such a high versatility’’. Textile producers have to tackle a wide variety of thicknesses, colors, materials and treatments. Weavers could therefore gain from the availability of flexible systems. However, because of technological issues, looms are still highly specialized with respect to materials and yarn thickness. Flexible machines do exist for other process steps, such as washing and finishing. However, due to the difficult market conditions, producers are not gaining benefits when introducing such innovations: ‘‘We offer our customers a very flexible machine. However, we are not able to ask them to pay a higher price because of the current market situation. On the other hand, it would now cost us even more to produce a traditional machine with lower flexibility and we are therefore stuck in a difficult situation in which the market expects flexibility, even though it does not value it’’. The interviewed winemaking company is a low-volume producer that operates in a niche. Even though it has chosen not to pursue variety with respect to bottles and labels, it has acquired a high-end and flexible bottling line essentially because of its reliability. ‘‘Our machine would allow us to fill different types of bottles and to attach paper and plastic labels, but we use only one type of bottle with one label because they represent our brand. However, we bought it because it was the only one allowing us to fill bottles in the safest way. We could even fill bottles with beer and other beverages, but this is not our business. We are willing to pay more even if we do not use such a broad flexibility, because of our primary attention to continuity of service’’. Producers of bottling lines stated that flexibility is quite important for volume producers that have to cope with many different bottles, labels and fluid content. Such flexibility is achieved through a modular architecture of the bottling line, which in the end does not lead to a substantial increase in costs: ‘‘we are always looking for new solutions in order to increase the flexibility of our solutions. Modularity has been an optimal approach allowing us to constantly introduce innovations.


25

These are the results of several compromises among what our customers wish and what technology allows’’. Surprisingly enough, no one of the system users mentioned organizational and cultural aspects as problems connected to managing flexibility in manufacturing. Instead, system producers often did, and especially the machine tool builder manufacturing FMSs. In their view, some of these aspects can be solved by tightening their cooperation with customers, involving both training and a continuing degree of customer support. However, they realize that not everything can be done by them. Customers must complete the process by appropriately integrating flexibility within their manufacturing operations and exploiting its full potential. 2.2.3.3 Flexibility Valuation Both users and producers perform very rough valuations of manufacturing systems, which generally do not allow to fully perceive and appreciate value coming from flexibility. The smaller metalworking firms (which are generally managed by owners) hardly use any quantitative considerations. Decisions are made through ‘‘rules of thumb’’, and flexibility is generally bought because it is found in high-end machines, which can help to improve the image of their company in the eyes of its customers. Large companies use payback as an investment appraisal method, based on their two-to-three year manufacturing plans. Provided that the investment satisfies the payback limit, they tend to allow manufacturing engineers some freedom in choosing the technology and its flexibility level. In any case, no company examines a mid-to-long term plan and actively assesses flexibility as a competitive lever that may help the introduction of new products. The same goes for the other industries, where managers tend to select manufacturing resources by relying on their own experience and on qualitative considerations. System producers generally make some attempts in quantifying flexibility in technical terms, in order to show their customers the advantages deriving from it. Flexibility indicators are generally restricted to the operational level and do not involve business-level aspects. Among them, the most ‘‘strategic’’ indicator that we found is a ‘‘system convertibility’’ index. This indicates either a ‘‘residual value’’ of the system after the production of a product is phased out, or the ‘‘additional investment’’ that would be required in order to reconfigure the system for producing the subsequent product. It appears that this indicator ‘‘encapsulates’’ many notions that, in academic literature, are treated and discussed as ‘‘options’’.

2.3 Discussion: A Conceptual Model Once the data gathered from the interviews have been elaborated, a higher-level conceptual model to understand the role of flexibility in the current manufacturing environment is developed. The proposed conceptual model is inspired by

26


Narasimhan et al. (2004), who tried to understand why flexible technologies do not lead to the desired performance. The authors argued that the results coming from manufacturing flexibility depend on two dimensions: ‘‘flexibility competence’’ and ‘‘execution competence’’. The former represents the ability to correctly invest in advanced manufacturing technologies and to develop systems incorporating flexible resources. The latter represents the ability to convert flexibility capabilities into tangible, operational-level performance. Basically, ‘‘flexibility competence’’ is related to strategic actions and technological capabilities, while ‘‘execution competence’’ is connected to operations management and organizational aspects. According to the authors, flexible manufacturing systems often fail because firms lack either these forms of competence, or because they pursue approaches that are not coherent on these two aspects. In order to achieve a deeper understanding of these concepts, this chapter adopts an approach similar to the one used by Belassi and Fadlalla (1998), who examined the process and the dimensions through which competencies in flexible manufacturing are developed. With regard to flexibility competence, this framework can be integrated with the basic ‘‘manufacturing system development process’’ that has been followed within this book. The process is based on the four steps of (1) strategic planning, (2) system configurations designing, (3) system configurations valuing and (4) purchasing. In this process, system users deal directly with steps 1 and 3, while the system producer handles step 2. According to the empirical findings, this competence can be defined over three main axes: (a) stratware, that is the amount of strategic initiatives aimed at major flexibility, (b) hardware, that is the amount of manufacturing resources acquired, and (c) software, that is the amount of computer-based programs that will support the management of manufacturing operations (Fig. 2.2). With regard to ‘‘execution competence’’ (Narasimhan et al. 2004), it is worth considering a process that involves producers (who provide training and customer care) and users (who must complete the integration process within the company’s operations and deal with day-by-day operational management). Two axis have appeared to be important in this context, and namely (d) orgware that is the organizational component, which must be aligned to common

Fig. 2.2 Flexibility competence


27

Fig. 2.3 Flexibility execution

objectives and culturally prepared to deal with a change, and (e) skillware that refers to fundamental skills for managing new systems (Fig. 2.3). This conceptual model is based on two competencies which are further exploded in a process and a set of dimensions. It has been mapped against the findings from case studies and seems to capture them fairly well. However, the model is quite complex and difficult to use in order to develop a methodology for supporting decision-making by practitioners. Therefore, it is proposed a synthesis of this model that can be more easily translated to a methodology incorporating algorithmic and/or rule-based decision support. For this purpose, three phases are defined (Fig. 2.4): (a) strategic-level decision making, (b) manufacturing plant configuration, and (c) converting flexibility into results. These phases are sequential and can originate a loop because the strategy needs to be adapted to internal behaviors. In this three phase process it is also easy to locate the role of each player. When this model is mapped with empirical findings, it becomes evident that it also represents the types of decisions and actions that system users and producers undertake when designing or upgrading their manufacturing systems fairly well. However, empirical evidence shows that these decisions and actions are seldom composed in a well-organized and well-integrated process. This often leads to inconsistencies, misalignment of objectives and suboptimal decisions.

Fig. 2.4 Flow chart of the conceptual framework

28


In the first phase, interviewed companies often perceive the strategic value of flexibility but are not able to execute it and take all the potential advantages. This can include either giving up investment in flexible machinery (despite the fact that flexible machines are currently becoming cheaper) or not fully using the flexibility that is available in the plant. Therefore, firms often prefer to enact uncertainty- and risk-mitigation strategies. To this purpose, for instance, one metalworking firm focused on serving a small market niche characterized by few customers, highly specific requirements related to precision and quality, small volumes and low product variety. In this way, they gave up the opportunity to exploit a very strong know-how and technology to expand their market. A large company invested heavily in market research to have a better understanding of the future demand scenario. However, they then decided to enter long-term and risk-sharing contracts with car makers that allowed them to reduce the amount of installed capacity and have much of the installed flexibility unused. In other industries, such as textile and winemaking, flexibility is perceived as a way to defend against uncertainty, and rarely as an ‘‘option to grow’’. In the second phase, choosing the optimal system configuration always comes from the search for an acceptable balance among flexibility needs and the machineries currently in use in the plant, which casts a very strong constraint in the design process. Metalworking companies often have substantial resources available, where older machines are typically dedicated and new ones are more versatile. The common approach is to defer investment as much as possible and to acquire new machines only when it is absolutely necessary. This often happens when the firm acquires an important contract and/or introduces a radically new product. Looking at flexibility execution, firms were generally in trouble getting flexible systems integrated with their organizational structure. Sometimes the organizational culture was not flexible and open to exploit flexibility. Some issues also are related to fundamental skills, for instance managing complex CNC machines, recovering from anomalies and breakdowns, etc. In the end, empirical findings confirm that companies do not embrace completely ‘‘rigid’’ or completely ‘‘flexible’’ manufacturing solutions. They rather confusedly tend to buy machines of good quality, which often have embedded flexibility which is then left unused. They do not realize the strategic potential of flexible machinery, and often ask producers to introduce some amount of customization into their machines in order to make them more efficient in manufacturing a specific set of products. Moreover, they tend to see the investment in manufacturing resources as an ongoing process of ‘‘manufacturing system evolution’’ rather than a onetime event. On the other side, system producers are finding that the cost gap between rigid and flexible machines is narrowing and, sometimes, a flexible machine is even cheaper to build than a rigid one. However, they share the difficulty in making customers pay for the value of flexibility, and in integrating machines with existing systems. At the same time, system


29

producers perceive a market opportunity in providing semi-customized systems. Even though the definition of this picture still needs to improve and become clearer, it is possible to state that there is a trend in manufacturing systems towards what can be termed ‘‘focused flexibility’’ (see Chap. 1; Cantamessa et al. 2007). Such trend, or paradigm, is quite unexplored from both an empirical and a normative perspective, and therefore raises the need for methodologies and algorithms dedicated to support the design of ‘‘focused flexibility systems’’.

2.4 Conclusions The chapter has tackled a deep understanding of the focused flexibility theory by presenting an empirical research based on case-studies performed on 12 Italian firms (both system producers and users). The aim was to gain a major insight into the flexibility from technological, operational and business perspectives. Research results point out that firms are currently conveying to intermediate solutions that this book is indicating as Focused Flexibility Manufacturing Systems. These solutions allow manufacturing firms to satisfy markets and handle the embedded uncertainty better than they did in the past with rigid or fully flexible solutions. Nowadays technology evolutions and initial scale economies are leading down the price and making these solutions highly competitive. Then, from the demand side, manufacturing firms are increasingly looking at FFMS as the real solutions able satisfy them because tailored right on their needs. Based on these empirical findings, the chapter has proposed a conceptual model to rationalize the ‘‘system acquisition process’’ that connects system producers and system users. This process is often managed with inconsistencies between phases, which cause misalignment between objectives and actions. The framework can be used by actors involved in the process such as the system producer or the system user singularly, or both together. In this way, they could be led to make capacity decisions more consistently with their needs and company future growth perspectives, and moreover they could use the framework as a tool to understand, plan and manage the dealing process with the counter-party. In this way, the concept of focused flexibility could be executed in more correct ways and could lead to better performance results. In addition, the proposed conceptual framework could be adopted by an external analyst for scientific purposes: in fact, it would be helpful to investigate the process in different industries or subindustries and to understand major dynamics and forces that drive a general system acquisition. Further researches should be dedicated to extend the empirical base to validate this proposed framework, and eventually improve it. At the end, Chap. 2 has highlighted the need to provide a structured methodology to support the system design process in the specific case of ‘‘focused flexibility’’ systems.

30


Appendix 1 – List of Interviewed Firms Table 2. 1 List of firms Firm Value chain

Industry

Description

Company [1]

Metalworking

Automatic systems for automotive applications (transfer lines) FMS, FMC and FFMS for automotive and aerospace sectors Automatic systems for filling and labeling wine bottles Jenny and mechanisms for different textile processing Machineries for treating weaves

Company [7]

System producer System producer System producer System producer System producer System producer System user

Company [8]

System user

Metalworking

Company [9]

System user

Metalworking

Company [10] Company [11] Company [12]

System user System user System user

Wine Textile Woodworking

Company [2] Company [3] Company [4] Company [5] Company [6]

Metalworking Wine Textile Textile Woodworking Metalworking

Systems for shearing and leafing wood panels Gear and transmission mechanisms for manufacturing machines and automotive industry Primary and secondary equipments for aerospace industry Fluid connectors for air conditioner and power steering systems Wine producer Wool weaving Wood panel producer

Appendix 2 – Interview Comparing Matrix Table 2.2 Comparing matrix for system producers (part 1) Firm Core business Industry market Business context Company [1]

Company [2]

Company [3]

Company [4]

Design and produce Automotive (car Increasing product mix due to industrial makers) product evolutions, new automation products, decreasing volumes manufacturing systems Design and produce Small to medium Increasing product mix due to: flexible ‘‘third producers’’: product evolutions, new manufacturing automotive, products, decreasing volumes cells and systems aviation, aerospace Produce filling and Winemaking High concentration, low labeling product variability, medium integrated systems environmental elements for wine bottles variability, volume uncertainty managed downstream Produce jennies and Textile and Increasing industrial dynamic, mechanisms for mechanic-textile increasing competition from

2 Flexibility in Manufacturing Table 2.2 (continued) Firm Core business

31

Industry market

different textile processes

Company [5]

Produce machineries Textile and for treating mechanic-textile weaves

Company [6]

Design and produce Woodworking manufacturing lines and machineries to shear and leaf wood panels

Business context far East players, crisis of European market, new input materials, changing demand peculiarities Increasing industrial dynamic, increasing competition from Far East players, crisis of European (especially Italian) markets, new input materials, changing demand peculiarities Small and specialized industry, high concentration (one player operates on the international scenario), high customer’s bargaining power

Table 2.3 Comparing matrix for system producers (part 2) Firm Uncertainty sources Flexibility concept Company [1]

Product types, product mix and product volumes

Company [2]

Product types, product mix, product volumes

Company [3]

Filling: Content (flat or sparkling wine), Bottle characteristics (height, width, shape)

Company [4]

Company [5]

Labeling: Bottle shape, Label positioning on the bottle Label characteristics: Shape, Type (transparent or not) Physical properties: Raw material, Fiber dimension characteristics, Input-output color, Jenny type, Spun yarn type based on Code, Wrench degree, Persistency and Regularity Physical and chemical properties: Yarn wrench degree, Fiber properties, Yarn origin

More product models on manufacturing line, possibility to reconvert manufacturing system, manufacturing capability scalability Under acceptable time-cost constraints, a flexible system is to be able to process a set of inputs, perform different manufacturing programs, generate a set of outputs Flexible system is to: be able to handle different uncertainty forms, be easy to use and maintain, have an acceptable technological availability-costs trade-off

Flexible system is to be adapted to different raw material physical properties

Flexible system is a modular system able to perform the 5 typical treating weaves activities according to the available technology

32


Table 2.3 (continued) Firm Uncertainty sources

Company [6]

Manufacturing type: Treatment, Required quality level Leafed: final scruff dimension, thickness, essence to be processed (standard or exotic) Sheared: thickness, final dimensions, essence to be processed (standard or exotic)

Flexibility concept

Machinery or manufacturing line bale to process different materials

Table 2.4 Comparing matrix for system producers (part 3) Firm Flexibility solution(s) Technology specifics Company [1]

Company [2]

Company [3]

Company [4]

Company [5]

Company [6]

Modular manufacturing systems with: single-chuck unit for mechanic finishing, multi-chuck unit for standard components FMC, FMS, FFMS

Modular systems. each module can be provided with a certain flexibility degree according to: technology availability, economic convenience, customer requirements Jenny: able to process different raw materials with different physical properties, dedicated to fiber type, able to process a certain set of product codes Modular machinery, each module is dedicated to a specific manufacturing activity, high versatility Standard essences: machineriesmanufacturing lines able to process input materials according to pre-set dimension ranges Exotic essences: machineriesmanufacturing lines able to handle all uncertainty elements and match customer requirements

Use of sequence of linear engines, high automation elements, robotics Cutting-edge sophistication on 3 main elements (process unit, tool stock, piece and equipment unit), use of automation and robotics for stand-alone systems Use of universal tools as well as versatile, parallel rigid units and check points

Use of electronics to improve automation, modular loglines to convey different raw materials to the same jenny Check systems to maximize work flow, maximize work quantity, minimize scruffs for no conformity to output specifics and reduce human error Use of electronics, particular materials handling, embossed chucks and laser devices


33

Table 2.5 Comparing matrix for system producers (part 4) Firm ‘‘Needs-solutions’’ Operation flexibility matching value Company [1] Yes

Improved production performance index

Company [2] Too much flexibility for FMSs

Yes in the case of FFMS Company [3] Yes

Company [4] No

Company [5] Too much flexibility (they cannot sell it, customers does not understand the real value) Company [6] Yes

Operation flexibility performance indicator

Product variety to be processed randomly or with setup, product mix tiding up frequency, average WIP time Improved performance They do not measure indicators, human operation flexibility for operator separated by their products machinery

Decreased set up time, decreased product mix variety, adaptability to vessel shape, major label variety Decreased set up time, improved production performance index performance Versatility in terms of: materials (weave type), manufacturing types

Qualitative standpoint: bottle variety, filling variety Quantitative standpoint: number of bottles that can be filled by time unit They do not measure operation flexibility for their products

Versatility in terms of qualitative (manufacturing variety, weaving variety) and quantitative (weave per hour meters) indicators Decreased need of Versatility is measured human resources in only from the qualitative production line, standpoint: type of improved production manufacturing process performance and type of processed material

Table 2.6 Comparing matrix for system producers (part 5) Firm Flexibility Flexibility Capital economic value economic value budgeting indicator(s) practices Company [1]

Recovery value

Productivity, investment usability, average system life that increases due to system

Net present value, scenario analysis, payback period

Customer investment decision makinga Strategic choices to introduce new products and increase manufacturing capability

34


Table 2.6 (continued) Firm Flexibility economic value

Flexibility economic value indicator(s) recoverability, investment scalability Not available

Company [2]

Saved working hours

Company [3]

Set up cost They do not have decreasing, indicators brand and marketing payback, manufacturing quality

Company [4]

Set up cost decreasing

They do not have indicators

Company [5]

They do not see an economic value for flexibility

They do not have indicators

Company [6]

Customers They do not have perceived the indicators flexibility value as high

a

Capital budgeting practices

Customer investment decision makinga

Net present value

Strategic and tactical choices to renew rolling stock and increase plant and system flexibility Rough Strategic choices valuations, to renew rolling qualitative stock, increase considera manufac turing tions capability and maximize production cycle automation Payback period Strategic choices to renew rolling stock, increase manufacturing capability and expand businesses to new market Cash flow Strategic choices to analysis renew rolling stock, increase manufacturing capability, diversify product mix and maximize production cycle automation Entrepreneurial Operation choices capabilities, to perform cash flow different types of analysis manufacturing activities and process no standard raw material

It refers to elements that lead potential customers to ask to system producers for a manufacturing system investment assessment.


35

Table 2.7 Comparing matrix for system users (part 1) Firm Core business Industry market Company [7]

Company [8]

Company [9]

Company [10]

Company [11]

Company [12]

Market niches small automotive players, aviation industry, International Aerospace (manufacturers), International

Few competitors in the domestic context, few customers, production volumes are never more than 50 units Information flows were totally upset after ‘‘09/11’’ events, high customer bargaining power, long term planning horizons

Automotive (car maker), International

Produce DOC and DOCG wines (especially Barolo variety) Produce and treat spun yarns and weaves with natural fibers

High-quality consumers, International

Low concentration degree, small size competitors, price taker, high customer bargaining power High environment uncertainty, few competitors

Produce multilayer poplar wood panels

Home furniture, caravan furniture, wood handcrafted manufacturing

Female tailor’s shops, International

Table 2.8 Comparing matrix for system users (part 2) Firm Uncertainty sources Flexibility concept Company [7]

Business context

Produce gear and transmission mechanisms for manufacturing machines and automotive industry Produce primary and secondary equipments for implementation systems, startup systems and fuel check systems Produce assembled tubes for air conditioning and power steering

Product mix: input dimensions, output characteristics

Something nice to have, thought as free machine versatility, it is not perceived as necessary

Huge field, a lot of competitors, especially from Far East countries, crisis of Italian market, changing market demand, decreasing lead times Small field, low concentration, fragmented, a lot of competitors, few European competitors, no international competitors

Adopted solutions for flexibility Machineries are rigid, they are considering to acquire some function integrators, they realize flexibility at the plant level, outsourcing several activities

36


Table 2.8 (continued) Firm Uncertainty sources

Company [8]

Changing volumes based on job order, customer requirements and lead time Product mix: piece types, low volumes, output quality

Flexibility concept

Adopted solutions for flexibility

Ability to process They select major added different pieces on the value components, same machinery new machineries tend to be more flexible, old machineries are utilized as exceeding manufacturing capacity, techniques to optimize production Company [9] Product type based on System ability to execute General purpose model news the main machineries, reducing manufacturing activity upstream uncertainty Model version by on more inputs in by negotiating rules evolution, geography, terms of different and risk assumptions input characteristics, materials and with contractors, manufacturing geometries studying the potential activity to accomplish success of each car Large and highly model before taking variable volumes, the job order small life-cycle products Company [10] Flat wine variety, need It is not perceived as Oversize filling and to satisfy customer necessary, filling labeling machineries needs, environment process must be events that affect raw executed safely and materials, and without stops therefore final products Company [11] Spun yard type by Lean manufacturing Internal orders handling codes, colors; processes to respect by component stock, manufacturing types, manufacturing times standardized treating practices and customer requests manufacturing variety process to create components, use of outsourcers for extraordinary orders Company [12] Raw material: Machinery adaptability Company strategy to dimensions, to process variables, optimize production structures; i.e. dimensions and cycle, standard end product: structures products supplied to manufacturing type, market, use of manufacturing components from variety, dimensions outside suppliers


37

Table 2.9 Comparing matrix for system users (part 3) Firm Technology specific(s) ‘‘Needssolutions’’ matching Company [7]

Rigid machineries oriented to execute precision manufacturing activities

Yes

Company [8]

Machineries characterized by: high automation degree

Yes (thank to optimizing production procedures)

High tool number Acceptable (time and cost)set ups

Company [9]

Machineries characterized by high automation degree, numerical control, flexibility in the quality control as well

Yes (thank to car makers’ long term plans)

Company [10]

These are the same elements as for company [3], given that they are their only supplier Use versatile machineries See company [5], they are their main supplier

Yes (thank to oversize machineries)

Company [11]

Company [12]

Use of a versatile machinery at the start of the manufacturing line, exactly where there is the need of flexibility. In this way, outputs can be standardized to reduce uncertainty along the downstream phases Versatility used as a way to reduce the need of human operators handling machineries

Yes (thank to continuous changes to production process) Yes

Operation flexibility value Increased product mix that can be processed by a machinery Increased manufacturing capacity Increased variety Human resources separated by the manufacturing machinery Manufacturing phases integrated on the same machinery, increased product mix, no other than check role assigned to human resources No measure

Potential use of standard components, dispatched orders by set time Reduced set up time, used components, reduced production process complexity

38


Table 2.10 Comparing matrix for system users (part 4) Firm Operation flexibility Flexibility economic performance indicator value Company [7]

Qualitative indicators

Company [8]

Number of performable pieces, manufacturing time cycle

Company [9]

Number of performable manufacturing activities, number of performable inputs in terms of materials and geometries Number of bottles that can be filled by time unit

Company [10]

Company [11]

Company [12]

Versatility from the qualitative standpoint in terms of type of manufacturing activities accomplished, manufacturing activity variety Number of manufacturing activities, type of manufacturing activity, dimension range of processed material

New machinery investment saving Set up costs saving compared with old machineries Cost reduction (given that they are price takers, cost reduction allows them to reach a higher gross margin)

Flexibility economic value indicator Qualitative indicators Qualitative indicators and production indicators Qualitative indicators and production indicators

Positive feedback from the market (to be translated to economic value), customer willingness to pay a few more High value perceived by the company, alas this value is not recognized by the customers

No measure

Manufacturing cost reduction, additional costs are turned to customers

Positive feedback for the market

Qualitative level

Table 2.11 Comparing matrix for system users (part 5) Firm Capital budgeting techniques Investment decision making Company [7] Rough evaluations, use of Driven by product, customer requirement, entrepreneurial experience and based on technical performance mind Company [8] Cash flow analysis, payback period Based on technical performance, consistency with production program, driven by new job orders Company [9] Cash flow analysis, use of Based on new job orders, time constraints, entrepreneurial experience, driven by customer needs recovery value Company [10] Rough estimations, qualitative Machinery reliability considerations

2 Flexibility in Manufacturing Table 2.11 (continued) Firm Capital budgeting techniques Company [11] Cash flow analysis, evaluations based on experience Company [12] Use of experience

39

Investment decision making Machinery reliability, possibility to expand to new markets Based on internal needs such as to increase capacity

Appendix 3 – Company Panel Analysis by Flexibility Dimension Table 2.12 Flexibility dimensions by company [1] [2] [3] [4] [5] p Machine flexibility Labor flexibility p Material handling flexibility p Routing flexibility p p Operation flexibility p p p Expansion flexibility p p p p Volume flexibility p p p p p Mix flexibility p p p p New product flexibility p p p p p Modification flexibility

[6] p p p

[7] p p

[8] p p

[9] p p

p

p

p p p

[10] p

[11] p

[12] p

p

p

p

p

p

p

p

p p p

p p p

p

p p p

p

p

p

p

Source – Koste and Malhotra (1999)

Interviewed companies were investigated to have a major understanding of, among all, what kind of flexibility they were utilizing internally or selling to their customers. Following some studies from literature (Koste and Malhotra 1999, Vokurka et al. 2000, Shewchuk and Moodie 2004), companies were analyzed based on ten classical flexibility definitions. Results shows that each company implements internally or sells at least three flexibility forms. Table 2.12 shows all the flexibility forms by company. The next chapter will consider several potential taxonomies and framework according to the multidimensional nature of flexibility and many contributions from reference literature. Then, it will introduce a flexibility ontology, defining a set of four basic flexibility dimensions – capacity, functionality, process and production planning -, listing four attributes – range, mobility, uniformity and resolution – and three basic levels – flexibility, reconfigurability, changeability.

40


References Belassi W, Fadlalla A (1998) An integrative framework for FMS diffusion. Int J Manag Sci 26(6):699–713 Boyer K, Leong K (1996) Manufacturing flexibility at the plant level. Int J Manag Sci 24(5):495–510 Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies an tools to design production systems with focused flexibility. Proceedings of DET 2007 – international conference in digital enterprise, Bath, UK, 19–21 September 2007, pp 627–636 De Toni A, Tonchia S (1998) Manufacturing flexibility: a literature review. Int J Prod Res 1587–1617 Handfield R, Pagell M (1995) An analysis of the diffusion of flexible manufacturing systems. Int J Prod Econ 39: 243–253 Koste L, Malhotra M K (1999) A theoretical framework for analyzing the dimensions of manufacturing flexibility. J Operat Manag 18:75–93 Lee B (1996) The justification and monitoring of advanced manufacturing technology: an empirical study of 21 installations of flexible manufacturing systems. Manag Account Res 7:95–118 Matta A, Tolio T, Karaesmen F, Dallery Y (2000) A new system architecture compared with conventional production system archotecture. Int J Prod Res 38(17):4159–4169. Narasimhan R, Talluri S, Das A (2004) Exploring flexibility and execution competencies of manufacturing firms. J Operat Manag 22:91–106 Shewchuk J P, Moodie C L (2004) Definition and classification of manufacturing flexibility types and measures. Int J Flex Manuf Sys 10(4):325–349 Tolio T, Valente A (2006) An approach to design the flexibility degree in flexible manufacturing systems. Proceeding of FAIM – flexible automation & intelligent manufacturing conference, Limerick, Ireland, 25–27 June 2006 Tolio T, Valente A (2007) A stochastic approach to design the flexibility degree in manufacturing systems with focused flexibility. Proceedings of DET2007 – international conference in digital enterprise, Bath, UK, 19–21 September, pp 380–390 Vokurka R J, O’Leary-Kelly S W (2000) A review of empirical research on manufacturing flexibility. J Operat Manag 18:485–501 Yin R K (1994) Case study research. Sage publications, London

Chapter 3

A Review on Manufacturing Flexibility Walter Terkaj, Tullio Tolio and Anna Valente

Abstract The topic of manufacturing flexibility has been addressed by many scientific contributions in the past years, thus highlighting the relevance of the problem both at industrial and academic level. Internal and external issues need to be faced at the same time when designing a manufacturing system and its flexibility; indeed, products and processes are easily and frequently changed by market and manufacturing strategies, while production systems must cope with relevant inertia which slow down their changes. Therefore, a fundamental issue consists of filling the modeling gap between a production problem and the manufacturing system best suited to face it. Current literature provides a huge research on the analysis of flexibility, as a solution to cope with uncertainty in the market and to support the manufacturing strategy. However, the link between the need of flexibility and the design of manufacturing systems is still weak. This need includes a deeper understanding of the nature of flexibility and, in turn, a clear definition of the dimensions of flexibility. This chapter reviews the state of the art of the literature on manufacturing flexibility by proposing also a conceptual framework for its formalization. Keywords Focused flexibility manufacturing systems (FFMSs) Flexibility review Ontology on flexibility

3.1 Current Literature on Manufacturing Flexibility Topic The previous chapters of this book have highlighted the importance and the complexity of designing manufacturing system characterized by the right degree of flexibility. In particular, Chap. 2 has stressed the industrial interest in this innovative vision as well as the main design difficulties which arise when firms take first steps towards the implementation of focused flexibility. W. Terkaj (*) Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy e-mail: [email protected]


41

42

W. Terkaj et al.

The flexibility degree of a manufacturing system represents a critical issue within the system design phase. Even though it is often considered a fundamental requirement for competitive firms, it is not always a desirable characteristic of a system. Frequently the literature on flexibility provides industrial examples where flexible manufacturing systems have unsatisfactory performance (Koren et al. 1999; Landers 2000), cases where available flexibility remains unused (Sethi and Sethi 1990; Matta et al. 2000), or cases where the management perceives flexibility more as an undesirable complication than a potential advantage for the firm (Stecke 1985). The analysis of the literature regarding the topic of manufacturing flexibility highlights the presence of four main categories of scientific works. In particular, within the first group many studies dealt with the analysis of the manufacturing flexibility meaning and its relationship with production problems. The second category includes works which tackled the classification of existing flexibility forms through taxonomies and conceptual frameworks. More recent papers focused on the development of approaches and models to support the system design while considering given system flexibility forms. These studies constitute the third category and although they provided important contributions on the manufacturing flexibility issue, the whole structure that supports the system design process starting from flexibility taxonomies is still weak. This aspect represents the core of the fourth literary group; in particular, concerning this last topic, an ontology on flexibility is briefly presented aiming at systemizing the high number of flexibility definitions since they could be helpful within the system design phase. The next sub-sections will present the works that can be grouped the four literature categories.

3.1.1 Manufacturing Flexibility Analysis The analysis of manufacturing flexibility has been faced by a large number of works. In this area a milestone work was presented by Upton (1994), who defined flexibility as the ability to change or react with low penalty in time, effort, cost or performance. Many authors considered manufacturing flexibility as the strategic answer to the current dynamic situation and the high degree of turbulence that affects the market (Slack 1983; Gerwin 1987; Kumar 1987; Sethi and Sethi 1990; Chen and Tirupati 2002). In many cases the analysis was supported by empirical studies as shown by Swamidass and Newell (1987). Other works studied how external changes are related to different forms of manufacturing flexibility and how they can be reduced. An example was provided by Gerwin (1993) as shown in Fig. 3.1. These works highlighted the need for investigating the relationship between the production requirements and the manufacturing flexibility forms (Upton 1994; De Toni and Tonchia 1998). In particular, a key issue is to identify the

3 Manufacturing Flexibility Fig. 3.1 Approach developed by Gerwin (1993)

43

Environmental Uncertainties

Manufacturing Strategy

Required Manufacturing Flexibility

Methods for Delivering Flexibility

Reduce Redefine

Performance Measurement

flexibility forms that face internal requirements, called internal flexibility, and the flexibility forms that cope with external turbulence, called external flexibility. This vision was stressed by Correa and Slack (1996) that developed two main categories of requirements leading to the need of manufacturing flexibility: the environmental uncertainty and the variability of the output required by the system. These two phenomena are called stimuli and impact on the production system through planned and unplanned changes. Planned changes happen as a result of conscious managerial actions which aim at altering some aspects of the system or its relationships with the environment. Unplanned changes occur independently of the intentions of the company, but they call for a reaction. This type of changes will be called stimuli acting on the system. Hyun and Ahn (1992) introduced the concept of proactive flexibility which takes into account possible future market changes. This allows firms to consider also strategies which are different from the simple reaction to market changes. In this sense, flexibility strongly impacts on the competitive levels of the firms. Gupta and Goyal (1989) proposed an approach to improve system flexibility in order to face short-term and long-term uncertainty. Goldhar and Jelinek (1983) identified in the flexibility concept the opportunity for companies to develop strategies mainly related to product variety while leaving markets characterized by scale economies. Grubbstrom and Olhanger (1997) focused on the temporal factor: flexibility is related to the time necessary to respond to changing conditions and can be considered as the measure of the difference between two admissible states of the system.

3.1.2 Taxonomies and Conceptual Frameworks The classification of existing flexibility forms through taxonomies and conceptual frameworks represents another topic which attracted many researchers. This body of literature addresses the importance of systemizing the knowledge concerning all the proposed flexibility forms. Moreover, the multidimensional nature of flexibility justifies the efforts, over time, which have been dedicated to the development of taxonomies where all the possible forms of flexibility are classified and characterized.

44

W. Terkaj et al.

Sethi and Sethi (1990) proposed a classification defining 11 different dimensions of flexibility. The provided framework consisted of three main groups: (i) Component or Basic flexibilities that included Machine, Material-handling and Operation flexibilities; (ii) System Flexibilities in which Process, Routing, Product, Volume and Expansion flexibilities were considered; (iii) Aggregate Flexibilities, e.g. Program, Product and Production, Market flexibilities. Moreover, the Organizational Structure as well as the Microprocessor Technology were transversally addressed by the authors. Gupta and Somers (1996) developed an instrument to measure manufacturing flexibility and carried out an empirical study to validate the dimensions of flexibility identified by Sethi and Sethi (1990). Gupta and Somers (1996) also examined the relationship among business strategy, manufacturing flexibility and performance. An empirical research over 269 companies showed that business strategy impacts on manufacturing flexibility that in turn impacts on organizational performance. Flexibility can be used to cope with environmental uncertainty and also to proactively create market uncertainties for competition (Gupta and Goyal 1989; Gerwin 1993). The study of Gupta and Somers revealed that the 11 forms of flexibility proposed by Sethi and Sethi can be reduced to 9 forms of flexibility: Machine, Material-handling, Process, Routing, Volume, Program, Product and Production, Market and Expansion and Market flexibility. De Toni and Tonchia (1998) contributed to the activity of conceptual systemization of the elder works on flexibility. Their work proposed a classification framework considering six main aspects of manufacturing flexibility, namely:

definition of flexibility (in general and with particular reference to the production field);

factors that determine the request for flexibility (variability of products and processes, internal and external environmental uncertainty);

classification (dimensions) of flexibility (hierarchical, by phases, temporal, by object of variation, or based on a mixture of the previous dimensions);

measurement of flexibility (direct, indirect and synthetic indicators); choice of determinant in obtaining flexibility (which can be distinguished in design or technological choices and organizational/managerial ones); interpretation of flexibility (strategic vs. operational, defensive vs. offensive, potential vs. effective, etc.). This framework was used to classify more than twenty years of research contributions on the topic. Among the various conclusions drawn by the authors, the subject of measurement of flexibility is seen as a field offering many opportunities for future research. Moreover, the authors examined in some detail the relationship between flexibility and company competencies. Latterly, they extended these ideas to propose a model for measuring manufacturing flexibility based on the characteristics of variation with which a process has to cope (De Toni and Tonchia 2002, 2003).

3 Manufacturing Flexibility

45

Flexible Manufacturing Capability Flexible Manufacturing Competence Volume Flexibility Machine Flexibility Labor Flexibility Material Handling Flexibility Routing Flexibility

Customer Satisfaction Mix Flexibility

Fig. 3.2 Framework proposed by Zhang et al. (2003)

The contribution proposed by Zhang et al. (2003) described manufacturing flexibility as an integral component of value chain flexibility, and discussed its sub-dimensions. It also provided a research theoretical model linking flexible manufacturing competencies with volume flexibility and mix flexibility, and with customer satisfaction (Fig. 3.2). An extensive literature review is carried out and the main concept of flexibility with its sub-dimensions is clarified including a recall to three distinctive attributes of flexibility: range, mobility and uniformity (Upton 1994). An analysis across a large number of organizations confirms empirically that flexible manufacturing competencies support the flexible capabilities of the firm, i.e. volume flexibility and mix flexibility, which in turn enhance customer satisfaction. Shewchuk and Moodie (1998) provided a framework which is very different from the ones presented in the rest of the literature and aims at developing a means for both classifying existing flexibility definitions (or, as the authors write, flexibility types and measures) and developing new definitions of flexibility, whether one needs to add some. The authors proposed a six-field hybrid classification framework which is then applied to map over 50 existing flexibility terms. This framework can be useful for having a first insight into the elementary components/dimensions of manufacturing flexibility. It also states that, in order to do this in a structured manner, one must start with suitable models and then derive the various flexibility types, based on the elementary components.

3.1.3 Design of Manufacturing Flexibility The third group of works deals with approaches and models to implement flexibility forms during the system design phase. As anticipated, even if in literature many efforts are devoted to the analysis of flexibility, the link between the knowledge about flexibility and the design of the manufacturing systems is still weak at the moment. On the one hand, some authors consider the flexibility

46

W. Terkaj et al.

acquisition as a strategic option to react to frequent volume changes and evolutions of technological requirements of products. On the other hand, many works highlight the need to deeply analyze the risk associated with purchasing high level of flexibility, taking into account the relevant investments (Stecke 1985; Matta et al. 2008). Other works have studied the relationship between the level of flexibility embedded into the system and the system performance (Koren et al. 1999; Landers 2000). Kulatilaka and Marks (1988) developed an approach which proofs the disadvantages related to the purchase of flexibility in production contexts affected by limited uncertainty. Even though the strategic importance of flexibility is generally well recognized, it is not easy to assess the value of flexibility when trying to financially justify the investment in modern flexible manufacturing systems or in advanced manufacturing technologies in general. Discounted Cash Flow (DCF) techniques are inadequate for applications where the benefits are mainly strategic and not easily quantifiable in terms of cash flow. Generally, it happens that the value of investment in advanced manufacturing systems possessing flexibility is underestimated. Ramasesh and Jayakumar (1997) proposed a new approach to generate the Net Present Value (NPV) of a manufacturing system, considering that the need for flexibility in a manufacturing system arises from the stochastic (i.e. uncertain) and dynamic (i.e. evolving over time) nature of the internal and external environments. Indeed, flexibility refers to the ability of the system to cope with the instability induced by the environment where the system operates. Bordoloi et al. (1999) developed a capacity expansion model by which an economic evaluation is accomplished to support the importance of flexibility and adaptability for manufacturing systems. The decision about when to buy flexibility is related to the risk analysis of investments (Kahyaoglu and Kayaligil 2002); in fact, flexible capacity is expensive and, indeed, the strategy to design high level of flexibility with uncertain information could involve significant costs. While many decision models deal with expected values of uncertain costs or profits, the reduced time span calls for proper risk management. Since there are actually many risk factors in system management, a recent tendency in logistics is the increased use of concepts borrowed from finance such as the quantile-based risk measure, i.e. Conditional Value-at-Risk (Brandimarte and Mottola 2007). Economic considerations regarding the flexibility gap – i.e. the gap between the level of actual flexibility and that required by the environment – are stressed by Llorens et al. (2005). Following this perspective, other works related to the corporate finance area can be mentioned (Kulatilaka 1988; Hodder and Triantis 1990; Trigeorgis 1996). They consider the flexibility notion as a financial option which can economically modify the company reaction to market changes that were not forecasted. ElMaraghy (2005) linked the concept of manufacturing system life-cycle to manufacturing system flexibility and reconfigurability. The author introduced the most recent views of a panel of experts from academia and industry on the


47

comparisons between flexible and reconfigurable manufacturing (Terkaj et al. 2008). A thorough comparison between FMS and RMS paradigms is also presented, and finally the concepts of flexibility and reconfigurability are treated considering the wider concept of changeability. Papers addressing the design of Focused Flexibility Manufacturing Systems (FFMSs) can be mentioned as well (Ganzi and Tolio 2003; Tolio and Valente 2006, 2007, 2008). The methods presented in these papers will be analyzed in Chap. 7 of this book.

3.1.4 Ontology on Flexibility A considerable research effort has been devoted to the definition of different forms of flexibility aiming at describing the characteristics of a manufacturing system. On the one hand, a given form of flexibility is considered as the capability of reacting to a well defined type of ‘‘stimulus’’ which can be experienced by the manufacturing system. On the other hand, a given form of flexibility may support various proactive strategies of the firm. Since the stimuli acting on the firm and the proactive strategies of the firm may differ, there is a need of various forms of flexibility. The result is that the number of flexibility types proposed in literature is really high even if some rationalization has been done. Other issues concern the ambiguous meaning of such flexibility form definitions and also the ambiguity among flexibility forms and other concepts (e.g. Expansion Flexibility vs. Reconfigurability). This situation cannot be overcome since a given form of flexibility is an answer to a very specific problem and the uncountable number of existing problems leads to uncountable flexibility forms. Terkaj et al. (2008) have addressed this problem proposing an ontology on flexibility which aims at both classifying flexibility definitions and leading the system design process by providing a structured framework for manufacturing flexibility. The work of the authors starts from the consideration that each form of flexibility (e.g. Mix Flexibility, Routing Flexibility, etc.) is a Compound Flexibility Form and can be interpreted as a recipe to tackle a specific production problem by combining some Basic Flexibility Forms (Fig. 3.3). Each Basic Flexibility Form is defined as the aggregation of two key concepts: Dimensions and Levels. Basic Flexibility Dimensions are general and theoretical concepts that should not find a direct implementation and should not be measured. These dimensions are embedded in the various forms of flexibility which can be found in specific applications. A set of four basic flexibility dimensions have been proposed as reported in Table 3.1. This set respects the property of ‘‘orthogonality’’, i.e. all dimensions in the set are independent and one dimension cannot be obtained as a combination of the other ones. Also completeness property is satisfied, i.e. each form of flexibility can be derived as a specific combination of the given dimensions, as it will be shown in Sect. 3.2.

48

W. Terkaj et al.

Fig. 3.3 Ontology on flexibility (Terkaj et al. 2008)

Each Basic Flexibility Dimension is further specified by four attributes: Range, Uniformity, Mobility and Resolution (Table 3.2). The first three attributes were defined by Upton (1994), while Resolution attribute has been added by the authors of the ontology. Attributes are treated at a conceptual level, without aiming at developing a metric. The key idea is that the concepts contained in the dimensions cannot be completely defined if the attributes are not introduced. The last concept proposed in the ontology on flexibility is the definition of Basic Flexibility Levels. These levels are related to real implementation of various forms of flexibility in the manufacturing system. For instance, a given basic flexibility dimension specified by its attributes may be present in a given system or it can be acquired if it is absent. In the second case, the system is one step behind compared to the first case, because of the need to take some actions to obtain the same capability. However, the fact that these actions can be taken Table 3.1 Basic flexibility dimensions (Terkaj et al. 2008) Basic flexibility Definition dimension Capacity Functionality Process Production planning

The system can do the same things at a different scale The system can do different things (different features, different level of precision, etc.) The system can obtain the same thing in different ways The system can change the order of execution or the resource assignment to do a given set of things


49

Table 3.2 Flexibility attributes Attribute Definition Range

Mobility

Uniformity

Resolution

Extension of the differences among the various ways of behaving under a given dimension. Range increases with the diversity of the set of options or alternatives which may be accomplished. For example, in the Functionality dimensions it represents how diverse is the set of different things which can be done by the system. Mobility within the range. It expresses the ease with which it is possible to modify the behaviour under a given dimension. Indeed, in order to start operating at a different point on a given dimension of change, there will be some transition penalty. Low values of transition penalties imply mobility in the space. For instance, in the Functionality dimension it may represent how easily it can move from doing one thing to performing another one. Uniformity within the range. It expresses how the performance of the system varies while moving within the range. If the performance is similar then the uniformity is high. For example, in the Functionality dimension it may represent the difference in capability or costs while doing different things. Resolution expresses how close the alternatives are within the range of a given dimension. Resolution increases with the number of viable alternatives if they are uniformly distributed within the range. For example, in the Functionality dimensions it expresses how short the distance is between similar but differnt thing which can be done by the system.

means that the system has a predisposition making it different from a system which cannot be modified. This predisposition is normally called in the literature ‘‘Reconfigurability’’ (Koren et al. 1999). The fact that a system is one step behind under a given dimension suggests the concept of ‘‘Level’’. At the top level of the ladder the given dimension considered is fully operational. At the lower levels of the ladder more steps must be taken in order to reach the top level. The levels of the ladder proposed by Terkaj et al. (2008) are defined in Table 3.3. Through the definition of basic flexibility levels, the proposed ontology allows to unify the concepts of Flexibility, Reconfigurability and Changeability (Wiendahl et al. 2007). All these concepts deal with modifications in manufacturing systems and the difference among them consists in timing, cost and number of steps necessary to implement a modification. The proposed ontology on flexibility is tested in this chapter carrying out two types of analysis. Firstly, the possibility to map all the forms of flexibility described in the existing literature through the basic dimensions and levels is investigated in

Table 3.3 Basic flexibility levels (Terkaj et al. 2008) Basic flexibility level Definition Level 1 (Flexibility) Level 2 (Reconfigurability) Level 3 (Changeability)

The system has the ability The system can acquire the ability already having the enablers The system can acquire the enablers

50

W. Terkaj et al.

Sect. 3.2. Secondly, the attention is focused on the forms of flexibility in industrial production contexts in Sect. 3.3.

3.2 State of the Art Analysis The Compound Flexibility Forms defined in the literature have been mapped according to the ontology proposed by Terkaj et al. (2008). Globally, 24 papers have been analyzed and 109 forms of flexibility have been found. The complete analysis is shown in Table 3.4; the Compound Flexibility Forms have been mapped defining which Basic Flexibility Dimensions are involved and at which Basic Flexibility Levels. The fields of the table stand for the referenced paper (‘‘Paper’’), the name of the mapped Flexibility Form (‘‘Compound Flexibility Form’’) and the name of the Basic Flexibility Dimensions: Capacity (‘‘Cap’’), Functionality (‘‘Func’’), Process (‘‘Proc’’), Production Planning (‘‘Plan’’). If a basic flexibility dimension is necessary to define a flexibility form, then the cell in the respective column is filled in with the related Basic Flexibility Level(s). For instance, Agility Flexibility as defined by Lee (1998) corresponds to Functionality Flexibility at Level 1. Table 3.4 Flexibility forms found in the literature mapped according to the proposed ontology Paper Compound Cap Func Proc Plan flexibility form Lee (1998) Gerwin (1993) Grubbstrom and Olhanger (1997)

Agility Change-over Change-over

– – –

Kara et al. (2002) Pagell and Krause (2004) ElMaraghy (2005)

Change-over Change-over

– –

Level 1 Level 1 Level 1, Level 2, Level 3 Level 1 Level 1

Control program Program

–

Level 1

Level 1

Level 1

–

Level 1

Program

–

Level 1

–

Level 1

Delivery

–

–

–

Level 1

Expansion

Level 2, Level 3

–

–

Expansion

Level 2, Level 3

–

–

Expansion

Level 2, Level 3

Level 2, Level 3 Level 2, Level 3 –

–

–

Sethi and Sethi (1990) Gupta and Somers (1996) Pagell and Krause (2004) Sethi and Sethi (1990) Bordoloi et al. (1999) Parker and Wirth (1999)

– – –

– – –

– –

– – Level 1


51

Table 3.4 (continued) Paper Compound flexibility form

Cap

Func

Proc

Plan

Kara et al. (2002)

Expansion

Level 2, Level 3

–

–

ElMaraghy (2005) Gupta and Somers (1996) Ramasesh and Jayakumar (1997) Gerwin (1993) Kara et al. (2002) Pagell and Krause (2004) Spicer et al. (2005) Kara et al. (2002) Kara et al. (2002)

Expansion Expansion and market Modification and expansion Modification Modification Modification

Level 2 Level 2, Level 3

Level 2, Level 3 Level 2 Level 2, Level 3 Level 2, Level 3

– –

– –

–

–

– – –

Level 1 Level 1 Level 1

– – –

– – –

Scalability Input Job

Level 2 – –

– – –

– – Level 1

Kara et al. (2002)

Job shop layout Launch Labor Work force

Level 1

– Level 1 Level 1, Level 2 Level 1

–

Level 1

– – –

– – –

Level 1

–

Kara et al. (2002) Zhang et al. (2003) Grubbstrom and Olhanger (1997) Ramasesh and Jayakumar (1997) Sethi and Sethi (1990) Gupta and Somers (1996) Kochikar and Narendran (1998) Parker and Wirth (1999) Kara et al. (2002) Zhang et al. (2003) ElMaraghy (2005) Gerwin (1993) Kara et al. (2002) Sethi and Sethi (1990) Gupta and Somers (1996) Kochikar and Narendran (1998)

Level 2, Level 3

– – –

Machine and labor

–

Level 1 Level 1 Level 1, Level 2 –

Machine

–

Level 1

–

–

Machine

–

Level 1

–

–

Machine

–

Level 1

–

–

Machine

–

Level 1

–

–

Machine Machine Machine Material Material Materialhandling Materialhandling Materialhandling

– – – – – –

Level 1 Level 1 Level 1 – Level 1 Level 1

– – – Level 1 Level 1 –

– – – – – –

–

Level 1

–

–

–

Level 1

–

–

52

W. Terkaj et al.

Table 3.4 (continued) Paper Compound flexibility form

Cap

Func

Proc

Plan

Kara et al. (2002)

Materialhandling Materialhandling Materialhandling Product Mix

–

Level 1

–

–

–

Level 1

–

–

–

Level 1

–

–

–

–

–

Product Mix

–

Level 1, Level 2 Level 1

–

–

Product Mix Mix Mix

– – –


– – –

– – Level 1

Mix

Level 1

Level 1

–

Level 1

Mix

–

Level 1

–

–

Mix

–

Level 1

–

–

Mix Mix (Production Capacity) Mix Mix

– Level 1

Level 1 Level 1

– –

– Level 1

– –

Level 1 Level 1

– –

– –

Mix Range

–

Level 1

–

–

Mix Response

–

Level 1

–

Level 1

Mix Response Mobility Operations

– – –

Level 1 Level 1 –

– – Level 1

Level 1 Level 1 –

Operation

–

–

–

Level 1

Operation Operation Routing

– – –

– – –

– Level 1 Level 1


Routing Routing

– –

– –

Level 1 –

Level 1 Level 1

Routing

–

–

–

Level 1

Zhang et al. (2003) ElMaraghy (2005) Grubbstrom and Olhanger (1997) Ramasesh and Jayakumar (1997) Chen et al. (2002) Gerwin (1993) Perrone and Noto La Diega (1996) Li and Tirupati (1997) Bateman et al. (1999) Shewchuk and Moodie (2000) Kara et al. (2002) Liberopoulos (2002) Zhang et al. (2003) Pagell and Krause (2004) Bateman et al. (1999) Bateman et al. (1999) Van Hop (2004) Kara et al. (2002) Sethi and Sethi (1990) Parker and Wirth (1999) Kara et al. (2002) ElMaraghy (2005) Sethi and Sethi (1990) Gerwin (1993) Gupta and Somers (1996) Kochikar and Narendran (1998)

3 Manufacturing Flexibility Table 3.4 (continued) Paper Compound flexibility form Parker and Wirth (1999) Kara et al. (2002) Zhang et al. (2003) ElMaraghy (2005) Kara et al. (2002) Kara et al. (2002) Kara et al. (2002) Sethi and Sethi (1990) Gupta and Somers (1996) Parker and Wirth (1999) Kara et al. (2002) ElMaraghy (2005) Gupta and Somers (1996) Sethi and Sethi (1990) Kara et al. (2002) Parker and Wirth (1999) Shewchuk and Moodie (2000) ElMaraghy (2005) Sethi and Sethi (1990) Kara et al. (2002) Parker and Wirth (1999) Shewchuk and Moodie (2000) ElMaraghy (2006) Perrone and Noto La Diega (1996) Kara et al. (2002) Seifoddini and Djassemi (1997) Kara et al. (2002) Kara et al. (2002) Correa and Slack (1996) Kara et al. (2002) Kara et al. (2002)

53

Cap

Func

Proc

Plan

Routing

–

–

–

Level 1

Routing Routing Routing Sequencing Pallet Fixture Parts Process

– – – – – – –

– – – – Level 1 Level 1 Level 1

– – – – – – –

Level 1 Level 1 Level 1 Level 1 Level 1 – –

Process

–

Level 1

–

–

Process

–

Level 1

–

–

Process Process Product and production Product

– – –


Level 1 – –

Level 1 – Level 1

–

Level 2

–

–

Product Product

– –

Level 1 Level 1

– –

Level 1 –

Product

–

Level 1

–

–

Product Production

– –

Level 1 Level 2

– –

– –

Production Production

– –

Level 1 Level 1

– –

– –

Production

–

Level 1

–

Level 1

Production Production

– –

Level 1 Level 1

– –

– –

Range Range

– –

Level 2 Level 1

– –

– –

Response Short term System robustness Tactical Technological

Level 2 – –

Level 2 Level 1 –

– – Level 1

– – Level 1

Level 1 –

Level 1 Level 1, Level 2

– –

– –

54

W. Terkaj et al.

Table 3.4 (continued) Paper Compound flexibility form Sethi and Sethi (1990) Gerwin (1993) Khouja (1995) Gupta and Somers (1996) Grubbstrom and Olhanger (1997) Ramasesh and Jayakumar (1997) Parker and Wirth (1999) Shewchuk and Moodie (2000) Kara et al. (2002) Zhang et al. (2003) Pagell and Krause (2004) ElMaraghy (2005)

Cap

Func

Proc

Plan

Volume

Level 1

–

–

–

Volume Volume Volume


– – –

– – –

– – –

Volume

–

–

–

Volume

Level 1, Level 2, Level 3 Level 1

–

–

–

Volume

Level 1

–

–

–

Volume

Level 1

–

–

–

Volume Volume Volume


– – –

– – –

– – –

Volume

Level 1

–

–

–

An analysis of the basic flexibility dimensions embedded in the different compound flexibility forms shows that:

71.56% of the forms is characterized by Functionality flexibility; 23.85% of the forms is characterized by Capacity flexibility; 27.52% of the forms is characterized by Production Planning flexibility; 9.17% of the forms is characterized by Process flexibility.

The literature mapping highlights the presence of a high variety of definitions concerning each form of flexibility: even if in most of the cases these definitions are quite similar in the content (e.g. twelve definitions of Volume Flexibility), the diversity in some definitions derives from the fact that each type of stimulus requires an appropriate form of flexibility. Another consideration coming from the literature classification is that some forms of flexibility are very simple since they are concentrated on a small number of dimensions and sometimes they coincide with a basic flexibility form (e.g. Machine Flexibility), while other flexibility forms (e.g. Mix Flexibility) are rather complex and include different dimensions. For these compound forms of flexibility it is therefore common to find variations that are rather difficult to compare without using the dimensions and the levels.


55

3.3 Analysis of Real Systems The ontology on flexibility (Terkaj et al. 2008) has been used to analyze some real production systems as well. The goal was to verify whether the requirements of flexibility addressed by these systems could be described by flexibility dimensions and levels. In the following sub-section an industrial case is analyzed according to the ontology; other examples of industrial case analysis can be found in the paper by Terkaj et al. (2008).

3.3.1 Mori Seiki Case Mori Seiki Co., Ltd., one of the biggest Japanese machine tool builders, proposes to its customers a range of solutions to face the increasing need of production system changes due to shorter and shorter product life-cycles. In particular, the production of components for the automotive market highlights two problems: the choice of the size of the machines and the need of frequently reconverting the machines and the line configuration due to changes in the specifications of the products. The problem connected to the size of machines is huge and still relevant. Indeed, big flexible machines are often characterized by relevant structure vibrations, high thermal distortions and other structural problems that make the meeting of quality specifications extremely expensive. To achieve highly stable and accurate machine tool operations over long operating periods, the complicated motion mechanism of versatile machine tool system should be simplified, avoiding indirect driving schemes as much as possible. For instance, Fujishima and Mori (2007, 2008) have proposed a Direct Drive motor solution to build high speed and high precision rotary axes. Moreover, in the past machines have been designed with a high degree of flexibility in order to process products of variable size. However, processed workpieces are usually small. Therefore, it is necessary to design the right degree of flexibility to process different product variants within the same system, but also to provide high capability to meet the strict product specifications imposed by the market. With this aim, Mori Seiki started the production of small, modular and flexible machines that can be integrated in reconfigurable lines. Machines of the NX series (Fig. 3.4) are machining centers designed for mass production applications. For example, machine NX3000 is endowed with a series of technical solutions which can be used to change the machine configuration. It has a structure which rapidly allows to pass from a 2-axis configuration to a 3-axis configuration and from a vertical to a horizontal configuration. Some structural characteristics have been introduced in order to make the machine more stable (e.g. the slides for the vertical motion are heavier in order to reduce vibrations). The low vibration together with the small size of the production modules allows

56

W. Terkaj et al.

Fig. 3.4 Mori Seiki machines of the NX series (courtesy of Mori Seiki)

higher precision in the operations. Moreover, the small size allows to reduce the thermal distortion. The advantage of smaller machines consists of high precision, high speed and efficiency as well as high accessibility to the workpieces, the table and the machine body. This means a reduction in the number of setups together with shorter time for maintenance of the machining units and an efficient chip disposal system. The reduced machine size has a positive impact also on the performance at a system level because it allows to design a more compact system layout that leads to shorter travel distances for transfer shuttles, lower number of robots for load/unload operations and a reduced floor space need. Two examples of system layout are shown in Figs. 3.5 and 3.6.

Fig. 3.5 Impact of small machines at a system level – travel distance is reduced by 30% compared to previous models (Courtesy of Mori Seiki)


57

Fig. 3.6 Impact of small machines at a system level – floor space is reduced (courtesy of Mori Seiki)

As it can be noticed from the description of the Mori Seiki case, a focused flexibility solution is proposed to reduce the waste deriving from the development of machines with excess flexibility when compared to the real needs of the customers. Mori Seiki manufacturing systems are provided with Capacity, Functionality, Process and Production Planning Flexibility. Capacity flexibility is given by the modularity of the machines. Indeed, being modular and highly interoperable, machines can be added or removed from a production line according to the current demand (Fig. 3.7). Removed machines can be eventually used as stand alone machines to accomplish different tasks, or can be organized in different lines. Therefore the system is characterized by Capacity flexibility at Level 2.

Fig. 3.7 Capacity flexibility through modularity (courtesy of Mori Seiki)

58

W. Terkaj et al.

Table 3.5 Mori Seiki case flexibility analysis Capacity Functionality Process flexibility flexibility flexibility

Production planning flexibility

Level 2

Level1

Level 1, Level 2

Level 1, Level 2

Functionality flexibility is provided at a machine level thanks to the ability of processing parts in the 2- or 3-axis configurations and in the horizontal or vertical configurations. Moreover, Functionality flexibility can be provided at a system level by introducing new modules with different characteristics. These properties can be used to process different product types. Therefore, Functionality flexibility is provided both at Level 1 and Level 2. The characteristics of the system can be also used to process the same part type with different machine/system configurations. In this sense, the system is endowed with Process flexibility at Level 1 and 2. Finally, the manufacturing system type proposed by Mori Seiki allows also Production Planning flexibility at Level 1, since it is possible to easily change the assignment of the operations to the machines. The analysis of the technological solution offered by Mori Seiki according to the ontology on flexibility is summarized in Table 3.5. The manufacturing systems offered by Mori Seiki are a clear example of systems with focused flexibility. The flexibility has been focused mainly thanks to the adoption of machining centers with a small work cube. Moreover, it is not required to adopt only general purpose machining centers; indeed, it is possible to acquire different machine modules to answer to different production requirements, thus tailoring the solution to the set of products.

3.4 Conclusions The introduction of focused flexibility may represent an important means to rationalize the way by which flexibility is embedded in manufacturing systems. In this sense, it is necessary to have a deep understanding of the nature of flexibility as well as to clearly define the dimensions of flexibility. The developed analysis has been supported by an extensive literature review and by adopting an innovative ontology on flexibility. Resulting evaluations emphasize the first findings of the empirical research developed in Chap. 2. Firstly, the production problems analysis, even in an evolutionary perspective, represents a very critical task for the companies. Making mistakes in production evaluation and forecasts can have strong impacts on the system design. Secondly, the presence in the literature of many formalization frameworks to classify and measure flexibility forms could confuse the decision maker instead of supporting him/her over the system design process. In order to address this problem the current chapter has proposed a framework to


59

systemize and clarify some important past research efforts. The same framework can also be used to support the design of new systems as suggested by Terkaj et al. (2008). Acknowledgments The authors would like to thank Mori Seiki Co., Ltd. for kindly providing the industrial case presented in Sect. 3.3. The research has been partially funded by the MUR (Italian Ministry for University and Research) under the PRIN project ‘‘Methodologies and tools for the configuration of production systems with focused flexibility’’, contract code: 2005097985.

References Bateman N, Stockton DJ, Lawrence P (1999) Measuring the mix response flexibility of manufacturing system. Int J Prod Res 37:871–880 Bordoloi S, Cooper W, Matsuo H (1999) Flexibility, adaptability, and efficiency in manufacturing systems. Prod Oper Manag 8(2):133–150 Brandimarte P, Mottola E. (2007) Mean-risk models in supply chain management. Proceedings of VIII Convegno AITeM, 10–12 September 2007 Chen Z, Li S, Tirupati D (2002) A scenario-based stochastic programming approach for technology and capacity planning. Comput Oper Res 29:781–806 Correa HL, Slack N (1996) Framework to analyse flexibility and unplanned change in manufacturing systems. Comput Integr Manuf Syst 9(1):57–64 De Toni A, Tonchia S (1998) Manufacturing flexibility: a literature review. Int J Prod Res 36(6):1587–1617 De Toni A, Tonchia S (2002) New production models: a strategic view. Int J Prod Res 40:4721–41 De Toni A, Tonchia S (2003) Strategic planning and firm’s competencies: traditional approaches and new perspectives. Int J Oper Prod Manag 13:138–52 ElMaraghy HA (2005) Flexible and reconfigurable manufacturing systems paradigms. Int J Flex Manuf Syst 17:261–276 Fujishima M, Mori M (2007) R&D activities of machine tools. Proceedings of 2nd international conference on changeable, agile, reconfigurable and virtual production. Toronto, Ontario, Canada, 23–24 July 2007 Fujishima M, Mori M (2008) Machine tools development for changeable factories. In: ElMaraghy H (ed) Changeable and reconfigurable manufacturing systems. Springer, New York Ganzi E, Tolio T (2003) Configuration and Re-Configuration of Manufacturing Systems with Focused Flexibility. 6th Convergno A.I.Te.M., Gaeta, 1–10 Sept 2003 Gerwin D (1987) An agenda for research on the flexibility of manufacturing processes. Int J Oper Prod Manag 7(1):38–49 Gerwin D (1993) Manufacturing flexibility: a strategic perspective. Manag Sci 39/4:395–410 Goldhar JD, Jelinek M (1983) Plan for economies of scope. Harvard Buinesss Rev 61:141–148 Grubbstrom RW, Olhanger J (1997) Productivity and flexibility: fundamental relations between two major properties and performance measure of the production system. Int J Prod Econ 52:73–82 Gupta YP, Goyal S (1989) Flexibility of manufacturing systems: concepts and measurement. Eur J Oper Res 43:119–135 Gupta YP, Somers TM (1996) Business strategy, manufacturing flexibility, and organizational performance relationships: a path analysis approach. Prod Oper Manag 5(3):205–233 Hodder J, Triantis A (1990) Valuing flexibility as a complex option. J Finance 4(2):549–565

60

W. Terkaj et al.

Hyun JH, Ahn BH (1992) A unifying framework for manufacturing flexibility. Manuf Rev 5(4):251–260 Kahyaoglu Y, Kayaligil S (2002) Conceptualizing manufacturing flexibility: an operational approach and a comparative evaluation. Int J Prod Res 40:2187–2206 Kara S, Kayis B, O’Kane S (2002) The role of human factors in flexibility management: a survey. Hum Factors Ergon Manuf 12:75–119 Khouja M (1995) The economic production lot size model under volume flexibility. Comput Oper Res 22(5):515–523 Kochikar VP, Narendran TT (1998) Logical cell formation in FMS, using flexibility-based criteria. Int J Flex Manuf Syst 10:163–182 Koren Y, Heisel U, Jovane F, Moriwaki T, Pritschow G, Ulsoy G, Van Brussel H (1999) Reconfigurable manufacturing systems. Ann CIRP 48(2):1–14 Kulatilaka N (1988) Valuing the flexibility of flexible manufacturing systems. IEEE Trans Eng Manag 35(4):250–257 Kulatilaka N, Marks SG (1988) The strategic value of flexibility: reducing the ability to compromise. Am Econ Rev 78(3):574–580 Kumar V (1987) Entropic measures of manufacturing flexibility. Int J Prod Res 25(7):957–966 Landers LG (2000) A new paradigm in machine tools: reconfigurable machine tools. Automation Conf. Ann Arbor, Proceedings of the 2000 Japan USA Flexible Lee GH (1998) Designs of components and manufacturing systems for agile Manufacturing. Int J Prod Res 36(4):1023–1044 Li S, Tirupati D (1997) Impact of product mix flexibility and allocation policies on technology. Comput Oper Res 24(7):611–626 Liberopoulos G (2002) Production capacity modeling of alternative, non-identical, flexible machines. Int J Flex Manuf Syst 14:345–359 Llorens FJ, Molina LM, Verdu J (2005) Flexibility of manufacturing systems, strategic change and performance. Int J Prod Econ 98:273–89 Matta A, Tolio T, Karaesmen F, Dallery Y (2000) A new system architecture compared with conventional production system architectures. Int J Prod Res 38(17):4159–4169 Matta A, Tomasella M, Clerici M, Sacconi S (2008) Optimal reconfiguration policy to react to product changes. Int J Prod Res 46(10):2651–2673 Pagell M, Krause DR (2004) Re-exploring the relationship between flexibility and the external environment. J Oper Manag 21:629–649 Parker RP, Wirth A (1999) Manufacturing flexibility: measures and relationship. Eur J Oper Res 118:429–449 Perrone G, Noto La Diega S (1996) Strategic FMS design under uncertainty: a fuzzy set theory based model. Int J Prod Econ 46–47:549–561 Ramasesh RV, Jayakumar MD (1997) Inclusion of flexibility benefits in discounted cash flow analyses for investment evaluation: a simulation/optimization model. Eur J Oper Res 102:124–141 Seifoddini H, Djassemi M (1997) Determination of a flexibility range for cellular manufacturing system under product mix variations. Int J Prod Res 35/12:3349–3366 Sethi AK, Sethi SP (1990) Flexibility in manufacturing: a survey. Int J Flex Manuf Syst 2:289–328 Shewchuk JP, Moodie C (1998) Definition and classification of manufacturing flexibility types and measures. Int J Flex Manuf Syst 10:325–349 Shewchuk JP, Moodie CL (2000) Flexibility and manufacturing system design: an experimental investigation. Int J Prod Res 38(8):1801–1822 Slack N (1983) Flexibility as a manufacturing objective. Int J Oper and Prod Manag 3/3:5–13 Spicer P, Yip-Hoi D, Koren Y (2005) Scalable reconfigurable equipment design principles. Int J Prod Res 43(22):4839–4852 Stecke KE (1985) Design, planning, scheduling and control problem of flexible manufacturing systems. Ann Oper Res 3:1–13


61

Swamidass PM, Newell WT (1987) Manufacturing strategy, environmental uncertainty and performance: a path analytical model. Manag Sci 33(4):509–524 Terkaj W, Tolio T, Valente A (2008) Focused flexibility in production systems. In: ElMaraghy H (ed) Changeable and reconfigurable manufacturing systems. Springer, New York Tolio T, Valente A (2006) An approach to design the flexibility degree in flexible manufacturing systems. Proceedings of FAIM – flexible automation & intelligent manufacturing conference, Limerick, Ireland, 25–27 June 2006, pp 1229–1236 Tolio T, Valente A (2007) A stochastic approach to design the flexibility degree in manufacturing systems with focused flexibility. Proceedings of the 4th international conference on digital enterprise technology, Bath, UK, 19–21 September, pp 380–390 Tolio T, Valente A (2008) A stochastic programming approach to design the production system flexibility considering the evolution of the part families. To appear in Int J Manuf Technol Manag – Special Issue on Reconfigurable Manufacturing Systems Trigeorgis L (1996) Real options: managerial flexibility and strategy in resource allocation. MIT Press, pp 69–83 Upton DM (1994) The management of manufacturing flexibility. Calif Manag Rev 36/ 2:72–89 Van Hop N (2004) Approach to measure the mix response flexibility of manufacturing system. Int J Prod Res 42:1407–1418 Wiendahl H-P, ElMaraghy HA, Nyhuis P, Za¨h MF, Wiendahl H-H, Duffie N, Brieke M (2007) Changeable manufacturing – classification, design and operation. Ann CIRP 56(2):783–809 Zhang Q, Vonderembse MA, Lim J-S (2003) Manufacturing flexibility: defining and analyzing relationships among competence, capability, and customer satisfaction. J Oper Manag 21:173–191

Chapter 4

Product-Process-System Information Formalization Marcello Colledani, Walter Terkaj and Tullio Tolio

Abstract This chapter introduces a conceptual framework for the integrated modeling of product, process and production system data. The work focuses on the Manufacturing System Design problem and aims at providing a common data structure as a reference for different methodologies and tools in this domain. The framework is flexible, extendible, scalable and has been developed as an object-oriented model by means of UML (Unified Modeling Language). Moreover, the proposed data model can have a wider applicability since it is based on shared standards and previous general frameworks. The concept of evolution has been introduced into the model, since it is essential to include market uncertainty in the design of competitive production systems. Finally, the developed framework has been translated into a relational database which can be interfaced with all the main phases of the system design approach presented in this book. Keywords Manufacturing information formalization Production system data Product data Manufacturing process data STEP-NC

4.1 Introduction Chapter 1 has already introduced the problem of manufacturing system design, highlighting the wideness and complexity of the activities that it is necessary to carry out in order to obtain effective system solutions (see Sect. 1.1). Above all, the turbulence of the market environment makes hard to tackle the configuration, reconfiguration, implementation, management, control and continuous improvement of the production systems which have to cope with the changes of products and processes. This chapter aims at establishing a common view and defining a common structure to handle the information used and generated during the design of manufacturing systems. From the industrial standpoint, this problem is highly W. Terkaj (*) Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy e-mail: [email protected]


63

64

M. Colledani et al.

critical since on one side many economic and technological issues must be jointly considered and on the other the final result has a strong impact on the profitability of the firm. System design can be time consuming and expensive, since qualitative and quantitative aspects are analyzed. Therefore there is the need of support tools to make the procedure of system configuration more efficient, so reducing the process time, and more effective, so increasing the chance to design the best configuration (Cantamessa et al. 2007). Chapter 1 has introduced system design as a complex problem which requires to share data among different activities (Fig. 1.3) including manufacturing strategy, process planning, system configuration, capacity planning and performance evaluation. A holistic and integrated view is necessary to model the most important relations among the different aspects of the manufacturing environment and it is also necessary to develop a unique standard framework to formalize data on products, processes and production systems. All the data necessary for system design activities have been formalized by following an innovative integrated data structure for evolving product-process-system. This integration is fundamental to optimally address the design problem, because most of the data are strongly related. The data framework has been enriched with the evolutionary concept which has been introduced to consider possible changes of the system (i.e. reconfigurations) as well as of the products/processes. Given the uncertain environment that manufacturing firms have to cope with, it is necessary to consider the evolutionary dynamic when designing a production system. Indeed, the system life-cycle is longer than the product life-cycle and, since the best system configuration is time-varying according to the product evolution, some system reconfigurations could be required to optimally address the production problems. The data formalization introduced in this chapter has been adopted as a reference by all the methodologies and tools that are described in the chapters of this book. The following section briefly analyzes the literature, Sect. 4.3 profiles a detailed object-oriented data formalization, while Sect. 4.4 presents its implementation in a relational database.

4.2 Literature Analysis The problem of data formalization has received much attention in literature: knowledge-based analysis methodologies and tools have been developed to support the decision making processes all over the product/process/system life-cycles. Bernard and Tichkiewitch (2008) made a contribution to this area, proposing a book with a complete overview of the knowledge life-cycle management topic with the most recent and innovative results. However, data evolution is not fully addressed by academic models and is not faced at all by industrial standards. Moreover, the integration among product, process and production system data have not yet been solved.

4 Product-Process-System Information

65

A framework to manage manufacturing information should be able to support the user in the production modeling activity and feed the decision support tools with the required data. Casati and Pernici (2001) have outlined four main requirements for a knowledge management framework:

Flexibility: the model must be easily adaptable in order to describe many different production system architectures, processes and product features.

Extendibility: the model must guarantee the potential for the user to rapidly extend the range and/or detail level, if needed.

Scalability: the model must be able to support product, process and production system descriptions at different levels of detail.

Integration: products, production processes and systems, together with their relations, must be considered and described in the same framework, since they all belong to the manufacturing environment. The problem of developing a data formalization framework for a manufacturing context has been traditionally faced by proposing solutions which can be in some cases easily adapted to different situations but which do not take into account all the requirements defined above. The main drawback is that existing models generally consider products, processes and production systems as separated from each other, and integration is not fully addressed. Moreover, the evolutionary aspect has been hardly faced, even if it has a deep impact on the performance of a manufacturing system (see Sect. 1.4). The following sub-sections briefly analyze the literature about product, process, production system and their integration.

4.2.1 Product and Process Product life-cycle issues have been examined in recent years from many different viewpoints. The available models range from marketing models, dealing with curves describing the evolution of product demands, to models dealing with the evaluation of the environmental impact on the product life-cycle (LCA – Life-Cycle Analysis), to management models dealing with the costs related to the various phases of the life-cycle, to more technical approaches considering product-process engineering activities along the life-cycle. What is still missing is a complete view from the perspective of the machine tool builders. This view should integrate the various viewpoints providing information to support the design of the production system life-cycle connected with the product life-cycle. The completeness attributed to this viewpoint is strictly connected to the need to describe the product evolution over time in terms of number and type of product variants, sales volumes and technological characteristics such as the raw piece description (e.g. shape and material) and the required machining operations (i.e. process plan).

66

M. Colledani et al.

The uncertainty affecting the product evolution, nowadays more critical than ever, should also be modeled in the most appropriate way. Important product information models are provided by industrial standards such as STEP (ISO 10303) and PLCS (ISO 10303–239). Anyway, these standards do not allow to describe both the geometric information about a certain product variant, and the information concerning the process cycle. This results in a static description of a product type, not considering the uncertain evolution over time of the different product variants. PSL (Process Specification Language) project (ISO/CD18629 2002) is an interesting approach in the field of process knowledge formalization. PSL provides a language for process data exchange to integrate multiple applications handling data related to processes throughout the manufacturing context life-cycle. Paying attention to the integration between product and process, the STEPNC standard (ISO 14649) presents a model of data interoperability between CAD/CAM systems and CNC machine tools. This standard has been taken as a reference to develop the product and process side of the data formalization presented in this chapter.

4.2.2 Production System From the production system standpoint, many works have been developed in the past to define languages and methodologies for its description, analysis and design. All these tools are useful but can be used only to describe the static and dynamic behavior of a single version of the production system. However, in everyday practice a system can undergo many kinds of evolution, driven mainly by product and process modifications. To model such changing systems, tools for the description of different evolution scenarios, with the related information concerning probabilities and durations, should be defined and used. Many works adopted an object-oriented approach to model manufacturing systems. In these works, the manufacturing system is decomposed into objects instantiated from classes. Each object has an identity, a state and a behavior following the object-oriented paradigm. Van Brussel et al. (1995, 1998) presented a holonic reference architecture for manufacturing systems modeled with UML class diagrams. Park et al. (1997) proposed an object-oriented modeling framework called JR-net for a generic AMS (Automated Manufacturing System); resource-type, job-type and controltype objects compose the model of a generic AMS. Kellert et al. (1997) proposed a conceptual model for FMSs (Flexible Manufacturing Systems). Booch et al. (2004) proposed another object-oriented model for FMSs. The authors adopted the OMT (Object Modeling Technique) formalism to model


67

the static portion of the system, DFD (Data Flow Diagram) for the dynamic and functional models, and STD (State Transition Diagram) for the control aspects. Bruccoleri et al. (2003) and Matta et al. (2004) proposed UML-based modeling approaches to describe all static and dynamic aspects of a cell controller and a complete FMS, respectively.

4.2.3 The Integration The need for integration of the two previous aspects (the product/process and the production system) directly derives from the viewpoint of the machine tool builder who wants the vision on the design and management of his product lifecycle (i.e. the production system seen as a product according to the vision proposed by the Manufuture Platform) to be as complete as possible. Moreover, the machine tool builder aims at deriving a guidance to handle the most critical issues occurring within the system design problem. For example, starting from the description of how the product will probably evolve over time, it is possible to take very critical decisions, e.g. whether to acquire some kind of flexibility at a certain degree, focused on some aspects relevant to his production problem, or to opt for more rigid and productivity-oriented system solutions. Regarding the integration of information, Kimura (1993) proposed a modeling framework for product and process under a virtual manufacturing point of view. Thibault et al. (2006) presented a tool called ‘‘Ontoforge’’ to support the integrated design of a forged product considering the knowledge about the ´ process and the information about the system. Lopez-Ortega and Moramay (2005) presented a meta-model using Express-G formalism to include STEP standard in a flexible manufacturing domain. Bernard et al. (2006) proposed a meta-model structure to link the function/behavior/structure applied to either product, process or resources and external effects. Colledani et al. (2008) have developed a formalized link between the production system side and the product/process side. Their work proposed a conceptual reference framework for the integrated modeling of product, process and production system data. The framework consists of an object-oriented model developed by means of the UML de-facto standard. The class diagram of this UML model, representing the core of the framework, is described in detail. The conceptual reference framework was developed to support both researchers and industrialists while modeling their problem solving methodologies. The basic idea is that a more effective use of heterogeneous decision support methods at different enterprise levels can be obtained if these methods are based on a common conceptual model. The authors have proposed also two initial

68

M. Colledani et al.

applications of the reference framework; one of these applications is about manufacturing system design and represents an earlier proposal of the data formalization presented in Sect. 4.3. The work by Colledani et al. (2008) has partly inspired the data structure presented in this chapter but the latter has been further developed focusing the attention on the manufacturing system side and introducing the concept of evolution.

4.3 Data Formalization for Manufacturing System Design The system design process plays a key role in defining the overall performance of competitive manufacturing systems having to face the trade-off between productivity and flexibility. The problem consists of designing the optimal system configuration, i.e. the number and type of resources needed to properly satisfy the demand. Technological requirements of the part types to be produced have a major impact on the selection of the types of resources to be adopted, while the production volume requirements influence mainly the choice of the number of resources (Tolio and Valente 2006). The system configuration and reconfiguration problem requires a data structure not only to describe an existing system but also to formalize the elements that can be added (removed) to (from) the reconfigured system. An effective support tool needs a complete and precise data formalization. For this purpose, a reference framework has been developed by adopting the UML Class Diagram formalism (Fig. 4.1). The class diagram in Fig. 4.1 shows three main areas: Product, Production System and Process. In the Product area, the technological and demand characteristic of the product are described. The following classes have been defined:

Workpiece; Machining Feature; Scenario Node; Production Problem.

In the Production System area the resources and the system characteristics are defined. Since in all this book the attention is centered on Focused Flexibility Manufacturing Systems (FFMS) and on Flexible Manufacturing Systems (FMS), the system resources can be machines, carriers, tool carriers, load/unload stations and pallets. Data related to the manufacturing system and its components are detailed by the following classes:

System; Selected System; Hyperplane;


69

Fig. 4.1 UML class diagram

Machine; Carrier; Load/Unload Station; Physical Pallet; Tool; Tool Carrier; Performance Evaluation.

The Process area describes, by means of the following classes, how the production system can produce the products:

Machining Operation; Machining Workingstep; Workplan; Pallet; Setup Face; Setup WP.

70

M. Colledani et al.

Fig. 4.2 Areas of the UML diagram

These three areas have been highlighted in the UML Class Diagram as shown in Fig. 4.2. The following sections describe all these classes and their attributes.

4.4 Product The ‘‘Product Area’’ (dotted line in Fig. 4.2) consists of the Workpiece (Table 4.1; Fig. 4.3), Machining Feature (Table 4.2; Fig. 4.4), Scenario Node (Table 4.3) and Production Problem (Table 4.4) classes; the first two classes are partially derived from the STEP-NC standard (ISO 14649). Each instance of the Workpiece class is one of the part types produced by the system and is related to the codes which can be ordered by the customers. Each Workpiece is characterized by a set of Machining Features (Table 4.2), i.e. geometric modifications which are realized by machining operations

4 Product-Process-System Information Table 4.1 Workpiece Attribute name id_workpiece its_material global_tolerance its_rawpiece_geometry its_geometry x_bounding_pos x_bounding_neg y_bounding_pos y_bounding_neg z_bounding_pos z_bounding_neg pen_out_cost ru_coeff

71

Attribute definition Workpiece type identifier Workpiece type material Workpiece type general tolerance Workpiece type raw piece geometry Final geometry of the workpiece type Positive coordinate along x-axis of bounding geometry Negative coordinate along x-axis of bounding geometry Positive coordinate along y-axis of bounding geometry Negative coordinate along y-axis of bounding geometry Positive coordinate along z-axis of bounding geometry Negative coordinate along z-axis of bounding geometry Penalty related to missing production; it can figure as an extra cost if outsourcing is adopted Product ramp-up coefficient

starting from the raw piece. According to ISO14649, there are different types of feature. Among them the most important are: planar face, pocket, slot, step, hole, generic feature and compound feature. The workpiece demand is affected by both mid-term and long-term variability. Long-term variability is modeled through the ‘‘Scenario Node’’ class which contains the demand evolutionary data according to a scenario tree representation. Since the production problem resulting from the combination of many products can be pretty hard to manage under an evolutionary perspective, the scenario tree representation (Fig. 4.5) has been adopted to simplify the problem formulation (Ahmed et al. 2003). Each scenario node is characterized by a realization probability and keeps a set of production problems inside. Indeed, mid-term variability is modeled by the ‘‘Production Problem’’ class (Table 4.4) whose instances are production contexts that a manufacturing system should be in principle able to satisfy without requiring a major reconfiguration. One Scenario Node explodes into one or more Production Problems (Fig. 4.5).

Fig. 4.3 Workpiece examples

72

M. Colledani et al.

Table 4.2 Machining feature Attribute name Attribute definition id_feature its_workpiece its_operations

abstract_supertype

placement_location_x placement_location_y placement_location_z cos_x cos_y cos_z

Identifier The workpiece type which the feature is part of The set of (machining) operations required to manufacture the feature. In this set of operations there can be alternative operations; for example, if a feature can be machined on two different machines then it is likely that the machines require a different operation (e.g. different cutting speed, feed, etc.) The type of feature (e.g. planar_face, pocket, slot, step, round_hole, toolpath_feature, profile_feature, boss, spherical_cap, rounded_end, thread) Position of the feature along the x-axis in the workpiece coordinate system Position of the feature along the y-axis in the workpiece coordinate system Position of the feature along the z-axis in the workpiece coordinate system Cosine of the angle between the feature working direction and the x-axis of the workpiece coordinate system Cosine of the angle between the feature working direction and the y-axis of the workpiece coordinate system Cosine of the angle between the feature working direction and the z-axis of the workpiece coordinate system

Both Scenario Node class and Production Problem class play a key role in the data model because they transform the framework from static and deterministic to dynamic and stochastic (see Sects. 7.3 and 7.4.1).

Fig. 4.4 Machining feature spotting


73

Table 4.3 Scenario node Attribute name Attribute definition id_scenario_node id_parent_node time_stage time_step

Node identifier Parent node identifier Node time stage Time period length which the demand is referred to (the length is the same for the nodes of the same time stage) probability Realization probability mean_part_mix_demand Mean demand volume of the workpieces in the scenario node min_demand Minimum demand volume of the workpieces in the scenario node max_demand Maximum demand volume of the workpieces in the scenario node min_agg Minimum value of the aggregate demand volume in the scenario node max_agg Maximum value of the aggregate demand volume in the scenario node budget Budget of the system user that is available for investment in a new system configuration discount_rate Discount rate associated with the node. It can be seen as a measure of risk as perceived by the system user

Table 4.4 Production problem Attribute name Attribute definition id_prodprob id_scenario_node part_mix_demand

Production problem identifier Identifier of the scenario node which the production problem belongs to Demand of the workpieces in the production problem

Fig. 4.5 Scenario tree

74

M. Colledani et al.

4.5 Production System In the ‘‘Production System Area’’ (continuous line in Fig. 4.2), the architectural characteristics of the manufacturing system are detailed. The System class (Table 4.5) is crucial since the definition of the system configuration is the final goal of the whole data formalization process and the system design problem itself. The system configuration is the technical solution proposed by a machine tool builder; this configuration can modify an existing system or define a new manufacturing system from ‘‘green field’’. The dynamics of the manufacturing system configuration can be also represented thanks to the ‘‘previous_system’’ attribute, which links a given system with its previous configuration. The link between the system configuration and the addressed production context is represented by the Selected System class (Table 4.6) which holds the decisions taken by the system user about the planning of the system capacity. The Selected System attributes detail which system configuration is chosen to face a particular Scenario Node and how the system configuration performs when facing that context (see Chap. 8). Table 4.5 System Attribute name Attribute definition id_system previous_system lead_time inv_cost op_cost machine_N carrier_N Lustation_N pallet_N tool_N open_time workplans ru_coeff sat_conf sat_sim vol_conf vol_plan vol_sim vol_plan_miss

System configuration identifier Previous system configuration identifier Lead time from the order issue to the installation of the new system configuration Investment cost of the new system configuration (i.e. the commercial bid of the machine tool builder) Operating cost of the system configuration Number of machines for each machine type in the system configuration Number of carriers in the system configuration Number of L/U stations in the system configuration Number of pallets for each pallet type in the system configuration Number of tools for each tool type in the system configuration Daily opening time of the system Set of workplans that are processed in the system System ramp-up coefficient Resource type saturation (value estimated by the system configuration activities) Resource type saturation (value estimated using simulation) Production volume of the system configuration in a scenario node (value defined by the system configuration activities) Production volume of the system configuration in a scenario node (value defined by capacity planning activities) Production volume of the system configuration in a scenario node (value estimated using simulation) Missing production volume of the system configuration in a scenario node (value estimated by capacity planning activities)


75

Table 4.6 Selected system Attribute Attribute definition name id_system root_node time_stage penalty

Selected system configuration identifier Identifier of the scenario node which is the root of the considered scenario tree Time stage during which the system configuration must be implemented Penalty related to missing production; it can be an extra cost if outsourcing is adopted

A System configuration is characterized by the possible combinations of production volumes that the system can yield. This property is modeled by the class Hyperplane (Table 4.7). The instances of Hyperplane represent the hyperplanes which are required to mathematically define the admissible production domain of the system configuration (see Sect. 7.4.4). The System is composed its physical resources: Machines (Table 4.8), Carriers (Table 4.9), Load/Unload Stations (Table 4.10), Tools (Table 4.11), Tool Carrier (Table 4.12) and Physical Pallets (Table 4.13). A Physical Pallet is the element consisting of various sub-elements (table, fixture, etc.) on which the workpieces are mounted and that enters the machine to execute the machining operations (see Sect. 7.4.2). The instances of the previous classes are either the types of resources composing the current system configuration or the types of resources which are available in the catalogue of the machine tool builder. Their attributes consist of the technological, physical and cost characteristics. Moreover, the Performance Evaluation class (Table 4.14) has been put into the model to define which system configurations must be evaluated. In this book the performance of the system are evaluated through the simulation technique (see Chap. 9), therefore the attributes of the class have been defined accordingly. Table 4.7 Hyperplane Attribute Attribute definition name id_hyperplane id_system id_resource resource_N rhs hyper_coef operator work_cost

Hyperplane identifier Identifier of the system which the Hyperplane is related to Resource type which the Hyperplane is related to Number of resources for each resource type (e.g. machine, carrier, etc.) in each system configuration Right hand side, i.e. total capacity of the resource type Coefficients of the hyperplanes defining the admissible domain of the system configuration Operator of the constraint: GT =greater than, GE =greater or equal, E =equal, LT = less than, LE =less or equal Production cost for each resource

76 Table 4.8 Machine Attribute name id_machine avail investment_cost axis_number axis_characteristics dim_x dim_y dim_z wcube_x pos_trav_x neg_trav_x speed_x accel_x wcube_y pos_trav_y neg_trav_y speed_y accel_y wcube_z pos_trav_z neg_trav_z speed_z accel_z pos_trav_B neg_trav_B speed_B accel_B pos_trav_tilting neg_trav_tilting speed_tilting accel_tilting power spindle_speed efficiency tool_change_time rotation_time tool_magazine failure_interval_type failure_interval_mean failure_interval_stdev repair_interval_type repair_interval_mean repair_interval_stdev operation_family precision_level

M. Colledani et al.

Attribute definition Machine type identifier Daily availability of the machine type Investment cost of the machine type Number of controlled axes in the machine Characteristics of the axes of the machine Dimension x of the machine type [mm] Dimension y of the machine type [mm] Dimension z of the machine type [mm] Work cube dimension along x-axis [mm] Positive travel along x-axis [mm] Negative travel along x-axis [mm] Speed in rapid movement along x-axis [mm/min] Acceleration in rapid movement along x-axis [mm/s2] Work cube dimension along y-axis [mm] Positive travel along y-axis [mm] Negative travel along y-axis [mm] Speed in rapid movement along y-axis [mm/min] Acceleration in rapid movement along y-axis [mm/s2] Work cube dimension along z-axis [mm] Positive travel along z-axis [mm] Negative travel along z-axis [mm] Speed in rapid movement along z-axis [mm/min] Acceleration in rapid movement along z-axis [mm/s2] Positive travel around B-axis [degree] Negative travel around B-axis [degree] Speed in rapid movement around B-axis [round/min] Acceleration in rapid movement around B-axis [degree/s2] Positive travel around tilting-axis [degree] Negative travel around tilting-axis [degree] Speed in rapid movement around tilting-axis [round/min] Acceleration in rapid movement around tilting-axis [round/s2] Maximum machine power [kW] Maximum spindle speed [rounds/min] Machine efficiency (necessary to calculate usable power) Time to change a tool on the machine type [min] Shuttle rotation time [min] Number of slots in the tool magazine Distribution of the time between failures Mean time between failures Standard deviation of time between failure Repair time distribution Mean repair time Standard deviation of repair times Operation family that the machine can execute (0 = prismatic; 1 =rotational) Precision level of the machine (0 = roughing; 1 = finishing)

4 Product-Process-System Information Table 4.8 (continued) Attribute name

77

Attribute definition

x_pallet

Position of the origin of the pallet coordinate system along the xaxis of the machine coordinate system Position of the origin of the pallet coordinate system along the yaxis of the machine coordinate system Position of the origin of the pallet coordinate system along the z-axis of the machine coordinate system Dimension of the pallet table which can be loaded on the machine

y_pallet z_pallet pallet_dim

Table 4.9 Carrier Attribute name


id_carrier investment_cost avail speed_carrier LU_time_carrier

Carrier type identifier Investment cost a unit of carrier Carrier daily availability Carrier speed [m/min] Time to load/unload a pallet from the carrier [min]

Table 4.10 Load/unload station Attribute name Attribute definition id_LUstation investment_cost avail operators buffer pallet_dim_min pallet_dim_max

Load/unload station type identifier Investment cost for a unit of Load/unload station Daily availability of the load/unload station Number of operators working on the load/unload station Number of slots in the load/unload station buffer Minimum dimension of the pallet that can be loaded Maximum dimension of the pallet that can be loaded

Table 4.11 Tool Attribute name


id_tool life regeneration_time diameter length tool_length investment_cost

Tool type identifier Tool life [min] Regeneration time [min] Tool diameter [mm] Length of the cutting edge [mm] Length of the tool [mm] Investment cost for each unit

Table 4.12 Tool carrier Attribute name


id_tool_carrier speed_tool LU_time_tool LU_time_tool_central investment_cost

Tool carrier type identifier Tool carrier speed Load/unload time Load/unload time from central magazine Investment cost for each unit

78

M. Colledani et al.

Table 4.13 Physical pallet Attribute name Attribute definition id_physical_pallet dim_x dim_y dim_z fix_dim_x fix_dim_y fix_dim_z investment_cost

Physical pallet type identifier Table dimension along x-axis [mm] Table dimension along y-axis [mm] Table dimension along z-axis [mm] Fixture dimension along x-axis [mm] Fixture dimension along y-axis [mm] Fixture dimension along z-axis [mm] Investment cost for each unit

Table 4.14 Performance evaluation Attribute name Attribute definition id_simulation id_system id_scenario_node replicates length warmup

Simulation run identifier Identifier of the system to be evaluated through simulation Identifier of the scenario node to be evaluated through simulation Number of replicates Length of the run [min] Length of the warm-up period [min]

4.6 Process The ‘‘Process Area’’ (dashed line in Fig. 4.2) describes how the system resources can be used to machine the workpieces. The Machining Operation (Table 4.15), Machining Workingstep (Table 4.16) and Workplan (Table 4.17) classes are partially derived from STEP-NC standard. Instances of the Machining Operation class describe the machining processes, specifying the tool to be used and a set of technological parameters. Table 4.15 Machining operation Attribute name Attribute definition id_operation retract_plane its_tool feederate cutspeed coolant spindle_speed power operation_type operation_family precision_level

Machining operation identifier The height of the retract plane associated with the operation Identifier of the tool that must be used for this operation Feedrate of the tool. The feed rate specified applies to the motion of the tool center point Cutting speed Coolant options Required spindle speed [rounds/min] Required power [kW] Operation type (e.g. milling, drilling, turning, etc.) Operation family which the operation belongs to (0 = prismatic; 1 = rotational) Precision level of the machining operation (0 = roughing; 1 = finishing)


79

Table 4.16 Machining workingstep Attribute name Attribute definition id_workingstep its_feature its_operation its_effect

its_secplane

ws_cutting_time its_tool_direction machine_set alternative_ws Predecessor Together

Machining workingstep identifier The manufacturing feature upon which the machining workingstep operates The operation which will be performed upon the machining feature The change to the geometry of the workpiece caused by the operation. A CAM system can use this attribute to describe the predicted effect of this operation on the geometry of the workpiece The security plane for the machining workingstep. On or above this plane, i.e. for z-value greater than this, a safe movement of the tool without danger of collision is possible Cutting time of the machining workingstep Tool direction Set of machine types where the machining workingstep can be processed Set of alternative machining workingsteps Set of machining workingsteps that are predecessors of the described machining workingstep Set of machining workingsteps that must be processed together (i.e. on the same pallet and same machine) with the described machining workingsteps

Instances of the Machining Workingstep class represent the machining process for a specific machining feature; a machining workingstep defines the association between a distinct feature and an operation to be performed on the feature. As the related operation, the machining workingstep is characterized by the use of a single tool and a set of technological parameters which are usually constant during the application of the machining workingstep. During the machining workingstep, no tool change is allowed. Compared to the STEP-NC approach, the Machining Workingstep class shows also the ‘‘ws_cutting_time’’ attribute and the ‘‘machine_set’’ attribute. The ‘‘ws_cutting_time’’ attribute defines the machining time needed to complete the workingstep, while the ‘‘machine_set’’ attribute represents the set of machine types which can process the machining workingstep. Process constraints are defined among the instances of the machining workingstep class.

Table 4.17 Workplan Attribute Attribute definition name id_workplan id_workpiece workingsteps pallets

Workplan identifier Workpiece type processed with the described workplan Set of machining workingsteps needed to complete the workplan Set of pallets with an execution sequence needed to complete the workplan

80

M. Colledani et al.

Table 4.18 Pallet Attribute name


id_pallet LU_time_type LU_time_mean LU_time_stdev physical_pallet N_parts N_setupface machine_set x_setupface y_setupface z_setupface

Pallet identifier Distribution of the time to load/unload all the parts on/from a pallet Mean time to load/unload all the parts on/from a pallet Standard deviation of the load/unload time Identifier of the physical pallet type related to the pallet type Number of parts mounted on the pallet Number of faces on the fixture of the pallet Set of machines where the pallet can be loaded Origin of the setup faces along the x-axis in the pallet coordinate system Origin of the setup faces along the y-axis in the pallet coordinate system Origin of the setup faces along the z-axis in the pallet coordinate system

A Workplan (Table 4.17) is defined as a collection of Machining Workingsteps together with an execution sequence. Moreover, a Workplan can be seen also as an ordered sequence of Pallet types. A Pallet type (Table 4.18) is the logical element that defines how a Physical Pallet (Table 4.13) can be used to process the workpieces. The workpieces are clamped on fixtures that are mounted on the Physical Pallets. Each fixture consists of one or more faces (Fig. 4.6). The Setup Face class (Table 4.19) defines which is the setup (i.e. the orientation) of the workpieces, while the Setup WP class (Table 4.20) defines the locations of the workpieces on the face.

Fig. 4.6 An example of tombstone fixture with four faces


81

Table 4.19 Setup face Attribute Attribute definition name id_setup_face pallet N_parts workpiece workingsteps rapid_time

cos_xx cos_xy cos_xz cos_yx cos_yy cos_yz cos_zx cos_zy cos_zz

Setup Face identifier Set of pallet types where the setup face is present Number of parts that are mounted on the setup face The workpiece type which is processed on the setup face. It is assumed that a setup face can have only one workpiece type (see Sect. 6.3) Set of machining workingsteps machined on the setup face Total rapid time to process a machining workingstep on all the workpieces which are mounted on a setup face. Rapid time depends on the machine where the machining workingstep is executed Cosine of the angle between the x-axis of the workpiece coordinate system and the x-axis of the machine coordinate system Cosine of the angle between the x-axis of the workpiece coordinate system and the y-axis of the machine coordinate system Cosine of the angle between the x-axis of the workpiece coordinate system and the z-axis of the machine coordinate system Cosine of the angle between the y-axis of the workpiece coordinate system and the x-axis of the machine coordinate system Cosine of the angle between the y-axis of the workpiece coordinate system and the y-axis of the machine coordinate system Cosine of the angle between the y-axis of the workpiece coordinate system and the z-axis of the machine coordinate system Cosine of the angle between the z-axis of the workpiece coordinate system and the x-axis of the machine coordinate system Cosine of the angle between the z-axis of the workpiece coordinate system and the y-axis of the machine coordinate system Cosine of the angle between the z-axis of the workpiece coordinate system and the z-axis of the machine coordinate system

Table 4.20 Setup WP Attribute name id_setup workpiece x_setupwp y_setupwp z_setupwp setupface n_row n_col d_row d_col

Attribute definition Setup WP identifier The workpiece type which the setup wp is related to Position of the setup wp along the x-axis of the setup face coordinate system Position of the setup wp along the y-axis of the setup face coordinate system Position of the setup wp along the z-axis of the setup face coordinate system Setup face which the setup wp is related to Number of rows on the setup face Number of columns on the setup face Distance between two workpieces on the same row Distance between two workpieces on the same column

82

M. Colledani et al.

4.7 Implementation The implementation of the data formalization model described above is a key aspect to be considered, since the proposed framework aims at real industrial world applications. This kind of data formalization model can be represented through both a relational database and an ontology. A database can give a more concrete and specific vision of the world, while an ontology is used to create a conceptual model of the world; a database focuses on the instances, while an ontology on the entities. Moreover, an ontology can be analyzed by ‘‘reasoning’’ methods which can help to extend the knowledge. During the work, it was decided to adopt a relational database implementation in order to guarantee an easier integration and data exchange among the modules composing the system design architecture. The relational database has been implemented using MS Access. An abstract of tables and relations of the database is reported in Fig. 4.7. The link between the data formalization classes and the database is shown by the following tables: product data (Table 4.21), resource data (Table 4.22), process data (Table 4.23), link between machine and process (Table 4.24), resources in the system configuration (Table 4.25), process in the system configuration (Table 4.26), performance of the system configuration (Table 4.27) and capacity plan (Table 4.28). It can be noted that implementing a relational database requires a large number of relations to be made explicit.

Fig. 4.7 Database relations


83

Table 4.21 Product data Database table

Related classes

Workpiece Machining_Feature Scenario_node Production_Problem relation_feature_workpiece relation_workpiece_scenario relation_workpiece_problem

Workpiece Machining Feature Scenario Node Production Problem Machining Feature, Workpiece Workpiece, Scenario Node Workpiece, Production Problem

Table 4.22 Resource data Database table

Related classes

Machine Carrier LU_station Tool Tool_carrier Physical_Pallet

Machine Carrier Load/Unload Station Tool Tool Carrier Physical Pallet

Table 4.23 Process data Database table

Related classes

Machining_Operation Machining_Workingstep Pallet Setup_Face Setup_WP Workplan relation_feature_operation relation_workplan_workingstep relation_workplan_pallet relation_workpiece_pallet relation_setupface_workingstep relation_setupface_setupWP relation_setupface_pallet relation_workingstep_workingstep relation_workingstep_together relation_workingstep_predecessor

Machining Operation Machining Workingstep Pallet, Physical Pallet Setup Face Setup WP Workplan Machining Feature, Machining Operation Workplan, Machining Workingstep Workplan, Pallet Workpiece, Pallet Setup Face, Machining Workingstep Setup Face, Setup WP Setup Face, Pallet Machining Workingstep Machining Workingstep Machining Workingstep

Table 4.24 Link between machine and process Database table Related classes relation_machine_setupface relation_machine_pallet relation_machine_workingstep relation_machine_workingstep_pallet

Machine, Setup Face Machine, Pallet Machine, Machining Workingstep Machine, Machining Workingstep, Pallet

84

M. Colledani et al.

Table 4.25 System configuration: resource data Database table Related classes System relation_system_machine relation_system_Lustation relation_system_carrier relation_system_pallet relation_system_tool relation_system_toolcarrier

System System, Machine System, Load/unload Station System, Carrier System, Pallet System, Tool System, Tool Carrier

Table 4.26 System configuration: process data Database table Related classes relation_system_workplan relation_system_machine_pallet relation_system_machine_workingstep relation_system_machine_workingstep_pallet

System, Workplan System, Machine, Pallet System, Machine, Machining Workingstep System, Machine, Machining Workingstep, Pallet

Table 4.27 System configuration: performance data Database table Related classes relation_system_carrier_scenario relation_system_LUstation_scenario relation_system_machine_scenario relation_system_pallet_scenario relation_system_workpiece_scenario relation_system_scenario Simulation

System, Carrier, Scenario Node System, Load/unload Station, Scenario Node System, Machine, Scenario Node System, Pallet, Scenario Node System, Workpiece, Scenario Node System, Scenario Node Performance Evaluation, System, Scenario Node

Table 4.28 System configuration: capacity plan Database table Related classes Selected_System Hyperplane relation_workpiece_hyperplane

Selected System Hyperplane Workpiece, Hyperplane

4.8 Conclusions The development of a common data structure for all the activities related to the design of manufacturing systems offers various benefits because it allows the integration of modules, tackling the different sub-problems, that are strongly linked by data exchange. The concept of evolution has been stressed since this kind of information must be provided to methodologies aiming at planning the life-cycle of a manufacturing system in an uncertain environment.


85

Even if the proposed data formalization has been developed to face the FMS and FFMS design problem, the work can be easily extended to other manufacturing domains thanks to its flexibility and scalability. In particular, information about demand volumes could be further detailed and aspects closer to production planning and system management could be modeled as well. Other potential future developments could aim at the creation of an objectoriented database to directly implement the data formalization framework described in this chapter without passing through a relational database. For example, an ontology about manufacturing could be realized following the object-oriented model. Acknowledgments The research has been partially funded by VRL-KCiP (Virtual Research Lab for a Knowledge Community in Production), a Network of Excellence in the 6th Framework Program of the European Commission (FP6-507487-2).

References Ahmed S, King AJ, Parija G (2003) A multi-stage stochastic integer programming approach for capacity expansion under uncertainty. J Glob Optim 26:3–24 Bernard A, Tichkiewitch S (2008) Methods and tools for effective knowledge life-cyclemanagement. Springer, New York Bernard A, Labrousse M, Perry N (2006) LC universal model for the enterprise information system structure. In: Brissaud D, Tichkiewitch S, Zwolinski P (eds) Innovation in life cycle engineering and sustainable development. Springer, New York, pp 429–446 Booch G, Jacobson I, Rumbaugh J (2004) The unified modelling language reference manual, Second Edition. The Addison-Wesley Object Technology Series Bruccoleri M, Noto La Diega S, Perrone G (2003) An Object-Oriented approach for flexible manufacturing system control system analysis and design using unified modeling language. Int J Flex Manuf Syst 15:195–216 Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceedings of the 4th International Conference on Digital Enterprise Technology, Bath, UK, 19–21 September, pp 627–636 Casati F, Pernici B (2001) Linguaggi per la modellazione dei processi aziendali. In: Batini C, Pernici B, Santucci G (eds) Sistemi informativi. Vol. II: Modelli e progettazione. Franco Angeli Colledani M, Terkaj W, Tolio T, Tomasella M (2008) Development of a conceptual reference framework to manage manufacturing knowledge related to products, processes and production systems. In: Bernard A, Tichkiewitch S (2008) Methods and tools for effective knowledge life-cycle-management. Springer, New York Kellert P, Tchernev N, Force C (1997) Object-oriented methodology for FMS modeling and simulation. Int J Comput Integr Manuf 10:404–434 Kimura F (1993) Product and process modelling as a kernel for virtual manufacturing environment. Ann CIRP 42(1):147–150 ´ Lopez-Ortega O, Moramay R (2005) A STEP-based manufacturing information system to share flexible manufacturing resources data. J Intell Manuf 16:287–301 Manufuture Platform, www.manufuture.org Matta A, Tolio T, Tomasella M, Zanchi P (2004) A detailed UML model for general flexible manufacturing systems. Proceedings of the 4th CIRP international seminar on intel-ligent computation in manufacturing engineering CIRP ICME ’04. June 30–July 2, 2004, Sorrento, Italy, pp 113–118

86

M. Colledani et al.

Park TY, Han KH, Choi BK (1997) An object-oriented modelling framework for automated manufacturing system. Int J Comput Integr Manuf 10(5):324–334 Thibault A, Siadat A, Bigot R, Martin P (2006) Method for integrated design using a knowledge formalization. Proceedings of 3rd conference on digital enterprise technology, Setubal, Portugal, 18–20 September 2006 Tolio T, Valente A (2006) An approach to design the flexibility degree in flexible manufacturing system. Proceedings of flexible automation & intelligent manufacturing conference, Limerick, Ireland, June 25–27, 2006, pp 1229–1236 Van Brussel H, Valckenaers P, Bongaerts L, Wyns J (1995) Architectural and system design issues in Holonic manufacturing systems. Pre-prints of IMS’95, IFAC workshop, Bucharest, Romania, October 1995 Van Brussel H, Wyns J, Valckenaers P, Bongaerts L, Peeters P (1998) Reference architecture for Holonic manufacturing systems: PROSA. Computers in Industry, special issue on Intelligent Manufacturing Systems, 37:255–276

Chapter 5

Manufacturing Strategy: Production Problem Analysis for Assessing Focused Flexibility Manfredi Bruccoleri, Diego Lanza and Giovanni Perrone

Abstract The objective of this chapter is to define an operationalization pattern which supports decision makers and managers in determining the level of manufacturing flexibility competences, given the business strategy and the manufacturing structure of the firm. This should drive the production system design and configuration activity. Specifically, this chapter presents an innovative approach to develop a manufacturing strategy, which is based on the idea that information on potential production problems that the manufacturing system could face throughout a given long-term planning horizon should be used as a starting point to determine the level of flexibility that the system should possess. Keywords Manufacturing strategy Focused flexibility Product life-cycle

5.1 Introduction As discussed in the introduction of this book, the recent competitive scenario, characterized by decreasing product life-cycles, market globalization, customized product requirements, and high demand uncertainty, has pushed manufacturing firms more toward the adoption of flexible manufacturing systems in order to achieve high levels of reactivity against future scenario uncertainty rather than traditional manufacturing solutions like transfer lines. On the other hand, in order to overcome the limits of flexible manufacturing system solutions (i.e. the high investment cost for their acquisition and the low capacity factor), academic research (Koren et al. 1999) and R&D departments of some machine tool builders as Cincinnati Machine, Lamb Technicon Machining Systems and Masco Machine (John Teresko 2002) have recently introduced the new concept of Reconfigurable Manufacturing Systems (RMSs). These are a mid-span M. Bruccoleri (*) Dipartimento di Tecnologia Meccanica, Produzione e Ingegneria Gestionale, Universita` degli Studi di Palermo, Palermo, Italy e-mail: [email protected]


87

88

M. Bruccoleri et al.

solutions between FMS and dedicated manufacturing systems, like transfer lines, and provide properties of scalability (i.e. the capability to easily change the production maximum capacity) and customized flexibility (i.e. the capability to perform a certain class of technological operations within a given part family). In other words, RMS is a manufacturing system with customized flexibility while FMS is a manufacturing system with general flexibility (Hu 2005; Hu et al. 2006). Scalability and customized flexibility are enabled by reconfigurable machine tools that are designed since the beginning for having a modular structure. This structure is initially configured for manufacturing a given number of part types at a certain production rate and is also suitable for being reconfigured by adding or subtracting machining or equipment modules in order to process other types of technological operation (‘‘similar’’ to the previous ones) and/or work with a different production rate. Thus, both scalability and customized flexibility are strictly tied to the design of machine tools and the related industry technology innovation rate. Reconfigurable machine tools (RMTs) are an essential enabler for RMSs. However, the current state-ofthe-art does not allow broadly reconfigurable machine tools to be available as the required technology is still back in various states of development (ElMaraghy 2005). Recent research studies highlight manufacturing systems designed by focusing the flexibility degree (FFMSs) could represent a strategic answer to production contexts characterized by demand changes. The flexibility customization is achieved by the hybrid architecture in which both general purpose and dedicated resources could be selected. In fact, system flexibility can be related to the flexibility of each single selected resource as well as the interaction among the resources composing the system. For instance, a flexible system can be composed of dedicated machines and highly flexible carriers (Tolio and Valente 2007). FFMS strategic design decisions involves two sets of options: (a) design a dedicated system in which the reconfiguration option can be implemented when production changes occur (similarly to the RMS solution); (b) purchase more flexibility than the amount strictly required by the current production problem in order to avoid future system reconfigurations and ramp-ups. In this case, FFMSs have some extra-flexibility designed to cope with future production changes, i.e. a degree of flexibility tuned both on present and future part families (Tolio et al. 2007). Therefore, from manufacturing strategy standpoint, the strategic design of the manufacturing system becomes more complex because it should also consider the definition of a flexibility domain and evaluate whether the focused flexibility solution is more efficient than FMSs or rigid systems. Specifically, the strategic design phase aims at addressing manufacturing system strategic variables based on enterprise competitive scenario, marketing strategies, financial and economics constraints and risk propensity. These variables consist of flexibility forms (mix flexibility, technology flexibility, volume flexibility, expansion flexibility and so forth), competitive policies (production mix and

5 Manufacturing Strategy

89

volumes etc.), ‘‘make or buy’’ strategies, and an estimation of the long-term capacity to be installed over a time horizon equal to the system life-cycle. The scientific literature on operations strategy shows that converting business strategy into manufacturing strategy and manufacturing strategy into flexibility competences is a very complex issue. This chapter presents some findings from a literature survey on manufacturing strategy vs. manufacturing flexibility and proposes an innovative approach for manufacturing strategy operationalization. It leverages the idea to exploit information on potential production problems as starting point for determining the level of flexibility that the manufacturing system should hold over the time horizon. Starting from this idea, this chapter proposes a methodology for generating a scenario tree of different and potential production problems, given a specific manufacturing strategy and the competitive landscape.

5.2 Research Background and Methodology A large body of literature deals with the issue of aligning manufacturing strategy with business strategy and with manufacturing system capabilities. Most of the researches usually propose theoretical frameworks for strategic alignment or empirical validations of the impact of being flexible to business performance. However, being flexible to produce many products requires a broader set of manufacturing policies than the case of being flexible to handle brutal volume variations. Moreover, flexibility requires general purpose machines, versatile workers, good information systems and many other elements that raise both initial investment and variable costs. Next, the risk associated with flexibility, as a manufacturing choice, entails a cost-benefit break-even analysis or some other trade-off considerations, which have brought up today to consider customized flexibility as an explicit set of manufacturing system design choices that need to be taken under a specific manufacturing goal. According to Miller and Roth (1994), specifying manufacturing strategy (MS) means defining two core elements:

the manufacturing goal the ‘‘pattern of choices’’ that the manufacturing function should make over time It seems to be intuitive that the pattern of choices should support the manufacturing goal while it is generally accepted that manufacturing goal should be consistent with the business strategy, as it is embedded in the ‘‘strategic fit’’ principle which has been firstly introduced by Skinner (1969) – he argued that ‘‘manufacturing becomes the missing link in corporate strategy’’. Many strategic management scientific papers deal with the ‘‘generic strategies’’ definition with regard to both the business and manufacturing area. A generic strategy can be considered as a meta-strategy – i.e. a strategic model companies

90


build their specific strategies up on. Generic manufacturing strategies can be described as a common pattern of organizing production, which is identifiable because commonalities occur in the way manufacturers organize their plants in order to achieve manufacturing objectives (Devaraj et al. 2004). The definition of a generic manufacturing strategy depends on choices and decisions to be made throughout the strategy definition that mainly concern the way by which the production is organized on different manufacturing dimensions. In the generic MS literature, Kotha and Orne (1989) framework is one of the most cited. The framework is graphically represented in Fig. 5.1 and represents the extension of the well-known Hayes and Wheelwright (1984) product-process matrix. Briefly, this framework identifies manufacturing strategies (i.e. goals and decision patterns) by classifying them according to the effects on the manufacturing structure that is represented by three dimensions. The first dimension – process structure complexity – refers to the well known process maturity concept. A complex structure process (mature process), typically used in the production of commodities, is characterized by strong interconnections among processing stages, while an immature process that exhibits many discontinuities in production, as a job shop, would have low process structure complexity. The second dimension – product line complexity – is a measure of the types and variety of product lines. A complex product line refers to product lines complex in design (customized production) while a simple product line refers to the production of commodity-like items. The third dimensions – organizational scope – is intended as the level to which the manufacturing function experiences vertical and horizontal integration of manufacturing operations. Such a dimension is strictly related to the outsourcing degree of low value manufacturing processes and no-core products. As mentioned, different strategic dimensions can be used for supporting a dominant strategy. The literature shows different models and frameworks that are based on these concepts (Hambrick 1983, Galbraith and Schendel 1983). The approach proposed by Wheelwright (1984) identifies two major dimensions

Process s maturityy

Process sructure complexity High

Veertical/ horizontal integration

Low

High

High

Organizational anizational scope

Fig. 5.1 Kotha and Orne (1989) framework

Product line complexity

Product structure (Haye & Wheelwright) (Hayes


91

by which the manufacturing function can contribute to the achievement of a given business strategy:

Market orientation: manufacturing choices need to be responsive to market demand; the system should produce a variety of products and manufacturing processes have to be flexible for producing customized, high quality and lowcost products. Technology orientation: manufacturing choices are led by the technology developments more than by the market demand. The way by which technology affects manufacturing strategic decisions is through automation and process innovation (Williams et al. 1995). Automation affects positively the level of sophistication of quality assurance programs and capacity planning process as well (Anderson et al. 1989). On the other side, process innovation concerns several areas, which influence manufacturing strategic decisions like robotics, materials, CAD-CAM systems, machine tools, etc. Manufacturing flexibility is the most important area where the manufacturing function supports the market orientation of the firm. As described in Chap. 3, different kinds of flexibility have to be settled for different kinds of customer specifications and requirements. For instance, the abilities to provide high product variety or to change production volumes can be achieved trough higher level of capacity slack or an increased use of general purpose machines (Chase and Aquilano 1992). This consideration is aligned with (Zhang et al. 2003), which argue that technologically advanced firms usually use special purpose machines characterized by low setup, waste and retooling costs. Figure 5.2 summarizes such considerations by setting down a pattern for MS operationalization based on the manufacturing dominant orientations and strategic variables.

Fig. 5.2 A pattern for MS operationalization based on manufacturing dominant orientations

92


The literature analysis that has been conducted shows that many theoretical frameworks have been proposed for establishing decisional paths to help managers and production system designers in defining manufacturing system specifications and assessing flexibility choices. The proposed frameworks, however, have to be interpreted from a conceptual perspective. Their practical adoption should involve a complex elaboration which strongly depends on the definition of the manufacturing strategy and the flexibility specification. The main issue concerns the definition of boundaries for the manufacturing function that the term MS and flexibility specifications refer to. As said in the introduction, MS ‘‘pattern of choices’’ deals with making some decisions, along many manufacturing dimensions, about manufacturing resources for achieving some strategic objectives. While restricting the field of dimensions into the manufacturing flexibility dimension surely simplifies the complexity of the problem, it should also be considered that the term manufacturing resource refers to several concepts. Indeed, a resource can be a single machine tool, a whole production system like an FMS or an even complex system such as a multi-plant multi-site system, or the entire value chain including all the resources needed in the product development as well as in the upstream supply chain. In such different scenarios a MS would involve very different decisions. Suppose, for instance, that a given strategic goal would bring the firm to decide whether to or not to invest in volume flexibility. This could mean to implement some outsourcing or sub-contracting strategies (according to a large perspective of the manufacturing function including suppliers and sub-contractors) or some production capacity slacks (when production decisions are limited to manufacturing system). Another example could be a firm whose manufacturing strategic objective is to be technology-oriented. Looking at single machines, this could lead the firm to introduce CNC machining centers while, looking at the whole production system, it could lead to introduce flexible automation in the material handling system (MHS) so enabling the system routing flexibility. The approach to elaborate manufacturing strategy into the flexibility assessment proposed by this chapter moves from the above considerations and leverages the importance of information on potential production problems to be faced in order to determine the right flexibility degree for the manufactuirng system. The result is a proposal of a framework that has practical implications over the design of focused flexibility manufacturing system.

5.3 MS Operationalization Based on Production Problems Generation In order to design a focused flexibility production system, it is necessary to have a major insight into the requirements which characterize the production problem. This means to deal with information about maximum quantities of each part to produce, part mix evolution, new part introduction, part removal, and


93

so on. This information represents production constraints that define a production volume domain of heterogeneous family of products that the system must be able to produce over a given planning horizon. The shapes of demand profiles for the different parts to be produced together with information about volume and mix uncertainty at each time step and per part, are the main output from the executing the business strategy process. It is the major information that the manufacturing strategy definition process should use as well, in order to determine some strategic system features as the right flexibility degree.

5.3.1 Scenario Tree Definition Since the production problem resulting from the combination of many products can be pretty hard to manage in an evolutionary perspective, a scenario tree representation can be adopted to simplify the problem representation (Tolio and Valente 2007). Evolution for production requirements could be graphically represented by a set of nodes and arcs. Nodes are the potential future states of production requirements, i.e. market demand and technological information of a production mix in a specific time period. Therefore a set of nodes corresponding to different time stages represents a specific scenario of the production requirement evolution process (Ahmed et al. 2003). Arcs are simply the time transition from a manufacturing state to the next one. Main characteristics of a production tree are as follows:

Random parameters evolve over the system life-cycle according to discrete time stochastic processes;

Each node of the scenario tree, except the root, has a unique parent, and each non-terminal node is the root of a sub-tree;

Each node is associated with a probability value. Consistently with data formalization from Chap. 4, each node (Table 4.3) contains technology data about part mix and probability values. A scenario node is characterized by information concerning:

Node identifier; Parent node identifier; Time stage the node belongs to; Time step whose length is the time period the demand refers to (the length is the same for the nodes of a given time stage); Realization probability; Demand volume for each part type. Moreover, nodes can be characterized by additional information such as budget constraints and financial availability.

94


5.3.2 Product Life-Cycle The intrinsic variability of the production problem can lead to different demand evolutions for each product. It is worth evaluating how much the system design process is affected by the demand variability and how much it is necessary to model these uncertainties. Since the goal is to assess focused flexibility solutions for given manufacturing strategies adapted to specific production problems, it would be reasonable to expect that the FFMS solution be more suitable when the production problem consists of a limited mix of part with medium to high volumes. For such a reason, an example of a real production context (interesting for the Focused Flexibility area) could be typically characterized by:

parts to be produced by the manufacturing system: these are components of final products that are manufactured or assembled furthermore by another manufacturer or assembler (typically an Original Equipment Manufacturer); part volumes evolve following the final product life-cycle, the bill of material quantities and the manufacturing strategy; few components types in the part mix; product evolution over time: different product versions can be introduced and/or be complementary. Figure 5.3 shows the product life-cycle shape that can be defined by five demand parameters as follows: 1. 2. 3. 4. 5.

Increase Start (IS) Increase End (IE) Decrease Start (DS) Decrease End (DE) Max height (V)

Product life-cycle must respect the growth-maturity-decline shape as Fig. 5.3 shows. IS IE DS DE As described by the following sub-sections, given a planning horizon (T), the parameters describing the demand life-cycle shape over T change depending on the total life-cycle IS–DE length, the maturity time interval IE–DS, and the planning horizon. Three different cases have been considered:

Medium life-cycle for IE-DS t0 (delayed entrance IR). An example of this new situation is reported in Fig. 5.15 and regards the case of long life-cycle and initial phase of growth. Considering the product life-cycle shape (Fig. 5.3) which has been defined according to parameters IS, IE, DS, DE, and V, it is necessary to define others two parameters that regard the introduction of the new component, respectively Fast Increase Start (FIS) and Fast Increase End (FIE). Figure 5.16 shows the two cases. In particular, the first case (on the left) refers to the immediate entrance of a new component while the second case (on the right) refers to the delayed entrance, and both are compared with the final product life-cycle which is described by a dashed blue line. The Fast Increase Start (FIS) represents the point when the new component is introduced (i.e. when its growth starts). In the case of immediate entrance (IM), at time t0 = 0, the FIS coincides with the IS (Increase Start), while in the case of delayed entrance (IR) the FSI will be obviously delayed with respect to the IS. The Fast Increase End (FIE), instead, represents the point when the phase of growth ends and the phase of maturity begins. Therefore, the new component

(a)

(b)

Fig. 5.16 New component life-cycle: Immediate entrance (a) and Delayed entrance (b)

104


life-cycle is given from the final product life-cycle and differs for the two parameters (FIS and FIE). Besides defining such new demand parameters, the possible scenario tree structures to be considered in the case of ‘‘differentiation’’ business strategy are identical to those of ‘‘focalization’’ strategy. Indeed, even if, for example, three different components (a, b and c) are taken into account, the scenario tree structure will present, as before, four ramifications at most as the main assumption is that the new (differentiated) component ‘‘c’’ is of the same type of the one of the components which have already been considered ‘‘a’’ and it is part of a final product ‘‘B’’ whose sub-components (at least one – ‘‘b’’) has already been considered.

5.5.1 Differentiation: Example Consider the case of two components a and c:

a is a component of the final product A, with a long life-cycle and initial phase of growth;

c is a new component of the same final product A. Both components are members of the same final product and the introduction of the new component has to be hypothesized. In this case a delayed entrance has been assumed and in particular the new component is introduced at time stage t = 3, as shown in Fig. 5.17.

5.6 Business Strategy: Diversification This section deals with the case in which the firm wants to diversify the production by producing a new component d (of the same kind as b), but part of the final product C. As in the differentiation strategy, the new component can be introduced immediately (Immediate Entrance) or later (Delayed Entrance) as well. Also in this case the scenario tree results from the composition of the configuration trees for all the components. However, differently from the case

Fig. 5.17 Scenario tree: the introduction of a new component c


105

of ‘‘differentiation’’ strategy, in the situation of three components (a, b, d), the scenario tree structure will present eight ramifications at most since the main assumption is: the new component ‘‘d’’ is of the same type of part ‘‘b’’, which has already been considered; however, ‘‘d’’ belongs to a different final product, i.e. ‘‘C’’, whose sub-components have not already been considered. For these reasons, the three components could be parts of three different final products.

5.6.1 Diversification: Example Consider the case of three components a, b and d:

a is a component of the final product A, with a long life-cycle and initial phase of growth;

b is a component of the final product B, with a medium life-cycle and initial phase of growth.

d is a component of the final product C, with a medium life-cycle and initial phase of maturity; In this case, there are three components of three different products and the scenario tree results from the composition of different product life-cycle. Therefore there will be eight ramifications, as shown by Fig. 5.18.

Fig. 5.18 Scenario tree: components (a, b and c) of the different final products

106


5.7 A Tool for Production Problem Generation This section introduces a decision support system (DSS) that has been developed for generating the production problem scenario tree starting from some information about final products, components and company business strategy. The DSS is a concrete tool for operationalizing the manufacturing strategy and is based on the scenario tree generation models that have been discussed so far. The DSS has been developed in Visual Basic programming language and integrated with a Microsoft Access Database sending out some input parameters in order to generate the scenario tree and receiving output results, i.e. the scenario tree which has been generated. The DSS is based on a windows-based interface which supports the planner throughout the whole manufacturing strategy operationalization process. Depending on the chosen business strategy (Fig. 5.19), the DSS leads the planner to define final products and component life-cycles in terms of demand parameters together with probability values associated with final product demand evolution uncertainties (Fig. 5.20). Once the user has inserted information about given strategy, final product demand profiles, bill of material of each products and work-pieces to be produced, the DSS determines the proper scenario tree structure related to the given problem and calculate all of the data settling on the nodes of the scenario tree. Specifically Fig. 5.21 shows a scenario tree structure represented as Microsoft Access tables (Table 4.21). By detail:

the table Scenario Node stores data about the scenario tree structure (one, two, four or eight ramifications);

Fig. 5.19 DSS forms for generating the scenario tree


107

Fig. 5.20 DSS forms for supporting the inputting of data on product and component lifecycles

the table Relation Workpiece Scenario stores data about each node product mix demand.

5.8 Numerical Example The numerical example consists of comparing two similar production problems. Both problems are characterized by data reported in Table 5.1. The two production problems only differ for the business strategy parameter FIS which is equal to 0 in Case 1 (i.e. immediate entrance) and is equal to 3 in Case 2 (i.e. delayed entrance). Both the production problems bring to the same scenario tree structure, which is made of 4 scenarios with occurrence probability equal to pB1 pC1, pB2 pC1, pB1 pC2, and pB2 pC2, respectively. However,

108


Fig. 5.21 A 2-ramification scenario three represented in a Microsoft access table

because of the different FIS values the variability of part mix and volumes in the Case 2 scenario tree is higher. Indeed, in each scenario, starting from time stage FIS, the three components of final product B have to be produced and this, for obvious reasons, increases the variability of scenario nodes volumes and mix. Table 5.2 reports the results of this numerical example in terms of average and standard deviation of volumes of cod380. The numerical example shows a simple application of the operationalization approach that has been proposed in this chapter. Indeed, the example compares two similar production problems that, however, require different levels of

5 Manufacturing Strategy Table 5.1 Numerical example information Settings Final product A Life-cycle length Initial stage Demand configuration parameters

SHORT GROWTH V0 = 2000; V = 4000; IE = 2; DS = 4; DE = 6;

Component codes

cod240 (QBOM = 1), cod268 (QBOM=1), cod270 (QBOM = 1) Focalization

Business strategy

109

Final product B

Final product C

LONG GROWTH V0 = 3000; pB1 = 0.3 (V = 6000; IE = 13); pB2 = 0.7 (V = 5400; IE = 5) cod280 (QBOM = 1)

LONG GROWTH V0 = 4000; pC1 = 0.7 (V = 7000; IE = 12); pC2 = 0.3 (V = 5700; IE = 7) cod380 (QBOM = 2), cod525 (QBOM = 1), cod916 (QBOM = 2) Diversification

Focalization

Table 5.2 Results from the numerical example Case FIS Scenario Occurrence cod380 volumes probability Average 1

3

2

0

1 2 3 4 1 2 3 4

0.21 0.49 0.09 0.21 0.21 0.49 0.09 0.21

7891.6 7891.6 7440.2 7440.2 8855.6 8855.6 8210.4 8210.4

cod380 volumes Standard deviation 5530.0 5530.0 5253.3 5253.3 4287.1 4287.1 4226.7 4226.7

flexibility (part mix and volumes are much more variable in Case 2, as proved by the higher level of cod380 volume standard deviation along the time horizon T). Such considerations are, hence, very important for the manufacturing system design phase and for establishing whether a FFMS solution is suitable for a given production problem or not.

5.9 Conclusions Twenty-five years later his seminal papers on manufacturing strategy, Wickham Skinner (1996) tried to explain in some ways why manufacturing strategy concepts (such as strategic fit, focused factory, trade-offs, plants-within-the plant, etc.) are as much flourishing and rapidly growing in popularity in academic literature as modestly, if not scarcely, used in the real industrial management practice. From that analysis the author recognized that, among the others, probably the main reason for that is imputable to the fact that ‘‘. . .we ask

110


manufacturers to explicitly describe a manufacturing task and then design all the structural elements to set up an internally coherent system to fit the task. But how is this to be done?’’ (Skinner 1996). Basically, what is still missing is a set of tools and methods that help managers to ‘‘engineer’’ manufacturing strategies. The research presented in this chapter aims at giving a contribution along this direction, by proposing an operationalization framework that should support managers in translating manufacturing strategy decisions into specific manufacturing system design specifications.

References Ahmed S, King A, Parija G (2003) A Multi-stage stochastic integer programming approach for capacity expansion under uncertainty. J Global Optimiz 26:3–24 Anderson JC, Cleveland G, Schroeder RG (1989) Operations strategy: a literature review. J Operat Manag 8(2):133–157 Chase RB, Aquilano NJ (1992) Production operations management. Richard D. Irwin, Boston Devaraj S, Hollingworth DG, Shroeder RG (2004) Generic manufacturing strategies and plant performance. J Operat Manag 22:313–333 ElMaraghy HA (2005) Flexible and reconfigurable manufacturing systems paradigms. Int J Flex Manuf Syst 17:261–276 Galbraith C, Schendel D (1983) An empirical analysis of strategy types. Strat Manag J 4:153–173 Hambrick DC (1983) High profit strategies in mature capital goods industries: a contingency approach. Acad Manag J 26(4):687–707 Hayes RH, Wheelwright SC (1984) Restoring our competitive edge. Wiley, New York Hu SJ (2005) Paradigms of manufacturing – a panel discussion. In Proc of 3rd conference on reconfigurable manufacturing, Ann Arbor, Michigan, USA Hu SJ, Koren Y, Stecke KE (2006) Introduction. Int J Flex Manuf Syst 17:259–260 Koren Y, Heisel U, Jovane F, Moriwaki T, Pritschow G, Ulsoy G, Van Brussel H (1999) Reconfigurable manufacturing systems. Ann CIRP 48(2): 527–540 Kotha S, Orne D (1989) Generic manufacturing strategies: a conceptual synthesis. Strat Manag J 10:211–231 Miller JG, Roth AV (1994) A taxonomy of manufacturing strategies. Manag Sci 40:285–304 Skinner W (1969) Manufacturing – missing link in corporate strategy. Harv Bus Rev, 47(3):156–167 Skinner W (1996) Manufacturing strategy on the S curve. Prod Operat Manag 5(1):3–14 Teresko J (2002) Making machine tools reconfigurable, IndustryWeek, Publication Date 7.1. 2002, www.industryweek.com/CurrentArticles/asp/articles.asp?ArticleId=1284 Tolio T, Valente A (2007) Stochastic approach to design the flexibility degree in manufacturing systems with focused flexibility. Proc of 4th int conf on digit enterprise technol, Bath, UK, 19–21 Sept, pp 380–390 Tolio T, Terkaj W, Valente A (2007) Focused flexibility and production system evolution. Proc of 2nd Int conf on Chang, agile, reconfigurable and virtual prod, Toronto, Canada, 23–24 July 2007, pp 17–41 Wheelwright SC (1984) Manufacturing strategy: defining the missing link. Strat Manag J 5(1):77–91


111

Williams FP, D’Souza DE, Rosenfeldt ME, Kassaee M (1995) Manufacturing strategy, business strategy and firm performance in mature industry. J Operat Manag 13:19–33 Zhang Q, Vonderembse MA, Lim JS (2003) Manufacturing flexibility: defining and analysing relationship among competence, capability, and customer satisfaction. J Operat Manag 21:173–191

Chapter 6

Pallet Configuration for Approaching Mapping Requirements on Devices Giovanni Celano, Antonio Costa, Sergio Fichera and Barbaro Santangelo

Abstract The correct configuration of a system is a strategic problem whenever a tool manufacturer should select the optimal solution to tackle a specific production problem. Once information concerning the production problem has been provided to the machine tool builder, it is possible to start the technological analysis of the part family which represents a very critical phase of the system design process. In particular, process plans to produce the workpieces need to be defined. To reach this goal it is necessary to elaborate a mapping between the part types to be produced and the available manufacturing resources. To this purpose, each machining feature of the various part types is matched with an operation or a sequence of operations, taking into consideration the feasible setups. This chapter provides a procedure named Mapping Requirement on Devices generating different process plans. It is based on three main modules. The first module performs a setup planning procedure; the second module deals with the problem of pallet configuration, whereas the last module performs the sequencing of the part setups and generates a set of alternative process plans. These process plans will then be taken into account in the selection of system resources. The results obtained in the testing phase address the importance of developing a procedure based on multi-setup fixtures instead of considering a single setup per pallet. Keywords Process planning Setup planning Pallet configuration Setup sequencing

6.1 Introduction The system configuration approach proposed in this book defines the characteristics of manufacturing systems designed to achieve the optimal trade-off between productivity and flexibility. To this aim, the number and type of A. Costa (*) Dipartimento di Ingegneria Industriale e Meccanica, Universita` degli Studi di Catania, Catania, Italy e-mail: [email protected]


113

114

G. Celano et al.

resources which are able to properly satisfy a given production problem need to be selected. Usually, a machine tool builder invests a considerable amount of time and money in the design of a production system. However, the final solution is usually obtained on the basis of its experience and few tools focused on specific tasks support the design process. During this activity it is possible to compare different process options and to evaluate their benefits. In particular, the system designer can provide a wide set of alternative machine configurations starting from the analysis of alternative process plans. The identification of the setups required to produce a part is one of the key issues that characterizes the process planning problem. Indeed, a proper ‘‘setup planning’’ phase assumes a central role in the evaluation and selection of the best configuration of a machining center. In this work it is assumed that parts to be machined are mounted on a pallet (i.e. a physical device consisting of various components: table, fixture, etc.). This assumption is quite general and applicable to many industrial cases. One consequence of this assumption is that, in addition to the machining centers, the pallets also need to be properly configured. The aim of this chapter is to address the setup planning and pallet configuration problem, in order to support the system designer during his activities. Indeed, at the end of the setup planning and pallet configuration procedure, a set of alternative process plans and their corresponding pallet configurations are generated. These elements represent an important input for the system configuration phase. This chapter is organized as follows. A brief literature overview is reported in Sect. 6.2; the problem statement and the proposed procedure are presented in Sect. 6.3. Sect. 6.4 discusses the setup planning procedure which consists of three steps: 1. workpiece setup generation; 2. setup face configuration; 3. tool path and rapid movements. The pallet configuration algorithm is explained in Sect. 6.5. The setup sequencing procedure which generates the different process alternatives is described in Sect. 6.6. Finally some conclusions have been drawn based on the overall methodology and on its theoretical implications.

6.2 Literature Background In the past decades, the setup planning issue has had a wide impact on the literature concerning Computer Aided Process Planning (CAPP) applications. Usually, setup planning has been considered as a tool supporting companies to cope with the increased product diversification (Wang and Luh 1996). In this study, however, the setup planning activity is seen as a strategic step of a wider

6 Pallet Configuration for Approaching Mapping Requirements

115

procedure, aimed at supporting manufacturing system design. Given these statements it is possible to define two different roles for the setup planning activity: an operating role, as an integral part of CAPP systems, which deals with the optimization of the shop-floor operations, and a strategic role which supports the system designer in the system configuration activity. An important investigation on the strategic role of setup planning for machining centers configuration has been provided by Contini and Tolio (2004). They proposed a method to define near-optimal setup plans for prismatic workpieces, when multiple parts can be mounted on the same pallet. Setups are determined taking into account the accessibility of the machining directions of the workpiece and the technological constraints among the required operations. Starting from the results of setup planning the authors also considered the pallet configuration issue as a key factor for an optimal configuration of machining centers. With reference to the operating role of setup planning, many authors dealt with this aspect by investigating the properties and performances of CAPP systems. One notable approach on automated setup planning in CAPP applications was performed by Zhang and Lin (1999), who utilized the basic concepts of hybrid graphs. They stated that setup planning in CAPP consists of recognizing machining features and extracting initial information, grouping to-bemachined features into setups, sequencing the setups, and selecting setup datums. The theoretically exact point, axis, or plane used to locate the part is referred to as a setup datum. The authors considered the tolerance analysis as a critical step of setup planning. In their algorithms all the parts are assumed to be machined on 3-axis vertical milling centers. More recently, Yao et al. (2007a,b) introduced a comprehensive system for the process planning of non-rotational parts. In their approach, setup planning plays a key role together with manufacturing resource analysis and fixture design. Since flexible manufacturing resources are used in mass customization, manufacturing planning must be designed to cope with these types of flexible resources. Thus, as stated by the authors, both manufacturing resource capability analysis (manufacturing resources include machine tools, cutting tools and fixtures) and setup planning (whose goal is to determine the number of required setups, the orientation of the workpiece and the process plan for each setup) represent the foundations of such manufacturing planning. Cai et al. (2008) proposed an adaptive setup planning approach which is applicable to various configurations of machine tools. Optimal setup plans are selected according to multiple optimization criteria. Starting from a 3-axis based machining feature grouping, all the setup plans of a given part are defined by examining the tool accessibility for different types of machine tools. Hebbal and Mehta (2007) focused their paper on the development of a formalized procedure for the automatic generation of feasible setups and the selection of the optimal setup plan for a prismatic part. They proposed a technique

116

G. Celano et al.

which simultaneously considers the basic concepts of setup planning from both machining and fixture viewpoints in order to formulate feasible setup plans. A similar optimization-based approach was suggested by Zhang and Peng (2005) who developed an approach for setup planning where setups are automatically planned, based on some key factors derived from machining practice: tolerance requirements, manufacturing costs and fixture constraints coming from fixture design. Setup planning and fixture planning are considered two closely related tasks of process planning which affect the overall cost and quality of the part to be machined. The integrated approach developed by the authors enables the user to simultaneously address setup planning and fixture design. Although most of the reported approaches efficiently address the setup planning issue for stand alone machines, it is apparent that the need for communication between a setup planning system and other planning and designing tools such as CAPP and Computer Aided Fixture Design (CAFD) has to be fulfilled. In this context, in order to emphasize the key role of information sharing within a planning and designing environment, an innovative approach based on Java and Web technologies, called ‘‘internet-based setup planning’’, has been proposed to handle the setup planning issue (Peng et al. 2005; Liu and Peng 2005).

6.3 The Process Configuration Issue 6.3.1 Problem Statement In accordance to the information formalization framework presented in Chap. 4, three main areas are involved in the decisional process when several process plans are taken into account to manufacture a product: the ‘‘Product’’, the ‘‘Process’’ and the ‘‘Production System’’ areas. For each area several classes have been defined, partially according to the STEP-NC standard (ISO/DIS 14649). The following classes define the input information needed to address the process configuration problem. Herein, the attributes related to each class have been omitted, while a comprehensive description is provided by Chap. 4:

Product area – Workpiece. This is the part to be produced within the system. It includes information concerning the geometrical dimensions of the part. – Machining Feature. This is the entity defining the workpiece technological requirements. Examples of machining features are: planar face, pocket, slot, step, hole, etc. The position and orientation of each feature within the workpiece coordinate system are defined through a set of linear coordinates and a direction cosine matrix respectively.

Production System area – Machine. This represents the machining centers available in the actual manufacturing system or in the machine manufacturer catalogue. The


117

main attributes involved in this study are: working cube dimensions, rapid traverse speed for each axis, number of controlled axes, machine power and pallet table size. – Physical Pallet. This is a physical element consisting of the combination of a table and a fixture with one or more faces (i.e. the fixture faces) which can be used to load the workpieces. The fixture dimension is the primary attribute to be considered for determining the number of pieces that can be loaded on the pallet.

Process area – Machining Operation. Each feature needs a machining operation to be processed: the machining tool and a set of technological parameters are required to define a machining operation. – Machining Workingstep. The association of a machining feature and a machining operation defines a machining workingstep. Thus, it represents a specific operation that a machine can make on a particular feature. Moreover, precedence and tolerance constraints among workingsteps are here characterized. Tolerance constraints are expressed in terms of machining workingsteps that must be processed with the same pallet and on the same machine. The process planning issue involves a setup planning activity which consists of defining the setups necessary to machine all the workingsteps required by a workpiece, with reference to the available system resources. Each machining workingstep is characterized by information on its working direction; thus, each setup needed by a workpiece can be associated with a group of machining workingsteps and also to a set of working directions. Whenever a workpiece is clamped on a fixture and then loaded onto a machining center, the manufacturing of each workingstep depends on the machine degree of freedom and, at the same time, on the specific setup selected for the workpiece. In fact, the main requirement to process a workingstep consists of the lining up between the workingstep working direction and the tool axis. Moreover, since several workpieces could be clamped onto the same fixture, some workingsteps could be inaccessible by the tool. As a consequence, given the workpiece clamping configuration on the pallet, the setup planning issue requires an efficient inverse kinematics analysis to verify whether each working direction is accessible by the machining tool, in order to select a set of distinct setups which allows the machining of all the workingsteps. Usually, a workpiece needs more than one setup to be processed and a pallet has more than one fixture face wherein workpieces can be loaded according to their planned setups. The pallet configuration problem consists of the generation of one or more alternative pallet configurations by matching the setups required by a workpiece with the different fixture faces available on a pallet. The amount of solutions that may arise from a pallet configuration procedure depends on the number of setups required by a workpiece and on the set of available pallet types. For instance, for a given part which needs four setups and

118

G. Celano et al.

for a physical pallet equipped with four fixture faces, it is possible to configure a maximum of four distinct pallets and a minimum of one pallet to process the workpiece. The former case means that all the fixture faces of a single pallet are arranged in the same manner, i.e. all the workpieces that fill up the fixture faces are clamped on with the same setup. The latter case means that each fixture face holds a different setup. Generally, machining workingsteps are linked to each other by precedence relations that arise from tolerance and technological constraints. The problem of defining the proper sequence of machining workingsteps becomes particularly important when a workpiece requires different setups to be machined. This means that a pallet can hold workpieces which are mounted according to just one setup or according to more than one setup. In both cases, a pallet must be processed respecting a precise sequence which strictly depends on the constraints among the workingsteps. Each sequence of pallets may be defined as an alternative ‘‘workplan of pallets’’ which entails integration between the setup planning and the pallet configuration activity.

6.3.2 Outline of the Proposed Procedure With reference to the aforementioned problem statement, the proposed approach, named Mapping Requirements on Devices (MRD), has been developed on the basis of the following main hypotheses:

Only prismatic parts have been considered as a workpiece to be processed. Workpieces can be processed by four- and five-axis horizontal CNC machines. All the operations required to machine a feature have to be performed in the same setup.

Only workpieces of the same type can be mounted on a pallet, i.e. no pallets holding different part types are allowed.

Each fixture face belonging to a pallet is configured with parts having the same setup.

All the available fixture faces of a pallet are occupied by parts to be machined.

The same setup is associated with opposite fixture faces in pallets with more than one fixture face, according to a symmetrical configuration.

Whenever a part requires four setups, a pallet with four fixture faces can be configured with parts having a different setup in every face. Figure 6.1 describes the structure of the MRD procedure which aims to address the process planning and pallet configuration problems. This procedure consists of three modules: 1. Setup Planning; 2. Pallet Configuration; 3. Setup Sequencing.


119

Fig. 6.1 The mapping requirement on devices procedure

The Setup Planning module is composed of three sub-modules. The first submodule, named ‘‘workpiece setup generation’’, generates the whole set of potential setups. The potential setups are defined starting from an initial clustering of machining workingsteps based on a three degree of freedoms machine configuration. Then, on the basis of the fixture dimension wherein the workpiece has been clamped, the second sub-module ‘‘setup face configuration’’ takes into account a four axis CNC machine and groups the machining workingsteps aiming at maximizing the number of workpieces clamped on the same fixture face. Afterwards, a single fixture face (associated with a given physical pallet) whereon a set of workpieces are mounted with the same setup is called ‘‘setup face’’. Due to the loading of more than one workpiece on each setup face, the setup face configuration problem takes into account the tool accessibility constraint by adopting a fixed tolerance distance between adjacent workpieces.

120

G. Celano et al.

For each configured setup face, the last sub-module ‘‘tool path generation’’ determines the tool path related to each machining workingstep taking into account the kinematic parameters of the considered machines when computing tool rapid feed rate times. The second module running within the MRD procedure is the ‘‘Pallet Configuration’’ module. It exploits the setup face configuration data determined by the previous module. Then, by matching this information with the available physical pallet data, it generates alternative pallets as a combination of several setup faces. As reported in the previous sub-section, the number of pallets that can be configured depends on the number of setups required by a given workpiece and on the physical pallet geometry expressed in terms of available fixture faces. The ‘‘Setup Sequencing’’ module completes the MRD procedure and combines pallet, workingstep and machine information to generate alternative workplans. Precedence constraints among workingsteps can involve workingsteps which have been assigned to the same pallet or to different pallets. The satisfaction of the precedence relations among workingsteps assigned to the same pallet is taken into account during the part program generation, while the Setup Sequencing module must generate alternative workplans (i.e. sequences of pallets) satisfying the precedence relations among workingsteps assigned to different pallets. All the modules composing the Mapping Requirements on Devices (MRD) procedure will be further detailed in the following sections.

6.4 Setup Planning In recent decades, computer numerical control (CNC) machines have improved their performances thanks to some auxiliary components such as four- and fiveaxis rotary tables. The proposed Setup Planning procedure manages three distinct problems for a given workpiece: the setup generation in relation to specific machines and physical pallets, the setup face configuration associated with each setup and the tool path and rapid feed rate time computation associated with each setup face. All of these problems will be addressed in the following sub-sections.

6.4.1 Workpiece Setup Generation According to the diagram reported in Fig. 6.1, the ‘‘Setup Planning’’ receives the geometrical and feature based workpiece data as input. Starting from a specific workpiece, a proper algorithm reads the working directions for each feature on the basis of its direction cosine matrix provided by the attributes of the ‘‘machining feature’’ class. The direction cosines describe the feature working direction, i.e. the so-called Tool Approach Directions (TADs), with respect to


121

an assigned workpiece linear coordinate system. Given a workpiece, a distinct placement is defined for each face of its envelope cube. Independently of the assigned features, the proposed Setup Planning procedure considers up to six different workpiece placements for a prismatic part. Whenever the unit vector of a face, defined with respect to the workpiece coordinate system, is aligned with the tool z-axis, then a so-called ‘‘standard placement’’ is individuated. The unit vector associated with each face of the workpiece envelope cube (e.g. see Fig. 6.2) identifies a Standard Placement Direction (SPD). As a consequence, each feature (or group of features having the same working directions) must be assigned to one of the six standard placements. Furthermore, machining features whose working directions are rotated with respect to the workpiece linear coordinate system are initially allocated to properly generated dummy placements. This is a common approach in setup planning literature where three degree of freedom machines are used to define the potential setups for a given workpiece (Zhang and Lin 1999). Since in this study a setup is defined as a specific workpiece standard placement combined with a specific workpiece orientation on a fixture face, different potential setups can be considered. In particular, 12 potential setups have been determined by taking into account a four degree of freedom machine which allows removing each rotated feature from its dummy placement and associates such feature to a properly selected potential setup. In fact, a four-axis machine can machine a rotated feature by taking advantage of its rotary table. Among those potential setups, only a minimum number of setups, named ‘‘ultimate setups’’, must be selected in relation to well-defined heuristic rules reported below. In order to explain how the Setup Planning procedure works, Fig. 6.3 presents two views of a sample workpiece characterized by five machining features: feature f1 is an

Fig. 6.2 Standard placements directions for a sample workpiece

122

G. Celano et al.

Fig. 6.3 Two views of the sample workpiece

oblique planar face, while features from f2 to f5 are blind holes. Feature f5 is symmetrical to feature f3, and it can be machined when the –Y standard placement direction is aligned with the tool z-axis. Moreover, each feature, properly associated with its required machining operation, determines a machining workingstep (e.g. WS1, WS2, WS3, WS4, WS5) In this study only horizontal machining centers have been taken into account; the machine coordinate system (Om) whose z-axis coincides with the spindle direction is reported in Fig. 6.4. Considering the orientation of the direction cosines of the workpiece linear coordinate systems (Owp) with respect to the machine linear coordinate system (Om), the standard placements of the workpiece can be defined as follows:

cos(zx) = +1, the machine spindle z-axis has the same direction and orientation of the workpiece x-axis;

cos(zx) = –1, the machine spindle z-axis has the same direction and opposite orientation with respect to the workpiece x-axis;

Fig. 6.4 Sample workpiece setup (i) and setup (iii)


123

cos(zy) = +1, the machine spindle z-axis has the same direction and orientation of workpiece y-axis;

cos(zy) = 1, the machine spindle z-axis has the same direction and opposite orientation with respect to the workpiece y-axis;

cos(zz) = +1, the machine spindle z-axis has the same direction and orientation of the workpiece z-axis;

cos(zz) = 1, the machine spindle z-axis has the same direction and opposite orientation with respect to the workpiece z-axis. Two possible setups arise from each standard placement, each one associated with a different workpiece orientation. Actually, four different orientations of the workpiece may be associated with a standard placement but only two of them can be considered as necessary to the setup planning activity. For instance, the four potential setups in the following list are defined as the combination of a standard placement and four distinct orientations: i. ii. iii. iv.

cos(zy) = +1; cos(yz) = +1; cos(xx) = 1; cos(zy) = +1; cos(yx) = +1; cos(xz) = +1; cos(zy) = +1; cos(yz) = 1; cos(xx) = +1; cos(zy) = +1; cos(yx) = 1; cos(xz) = 1;

As shown in Fig. 6.4, setup (i) and setup (iii) should be considered equivalent since features f1, f2, f3 can be likewise accessed by a four-axis machining center. As a consequence, setups (iii) and (iv) should be considered homologue to setups (i) and (ii), respectively; thus, only a couple of them should be taken into account to address the setup planning task. The total number of non-homologue possible setups for the prismatic part is equal to 12. Since it is assumed that all the workpieces clamped on a setup face have the same setup, both potential setups (i) and (iii), and potential setups (ii) and (iv) can be considered equivalent to each other. All the feature working directions (z-feature) of the sample part, computed with respect to the workpiece linear coordinate system, are reported in Table 6.1: Feature represents the feature code, Feature type is the type of feature according to ISO14649-10 and the direction cosines are related to the angle between the workpiece coordinate system (xwp, ywp, zwp) and each feature z-axis. Working on the basis of 12 potential setups as reported in Table 6.2, the Setup Planning procedure selects the minimum amount of ultimate setups

Table 6.1 The sample workpiece machining features Feature Feature type cos(xwp ) cos(ywp ) pffiffiffi pffiffiffi f1 Chamfer p2 p2 ffiffiffi=2 ffiffiffi=2 f2 Blind hole 2=2 2=2 f3 Blind hole 0 1 f4 Blind hole 0 0 f5 Blind hole 0 1

cos(zwp ) 0 0 0 1 0

124

G. Celano et al.

necessary to process all the machining workingsteps. The ‘‘Potential setups’’ column in Table 6.2 highlights how the same machining feature is allocated to several potential setups. The ‘‘Ultimate setup’’ column puts in evidence that this specific workpiece needs only three setups to be machined: the problem consists of selecting a set of potential setups able to perform the machining workingsteps required by the production problem. The decision about selecting a potential setup is influenced by all the rotated features which need a proper workpiece orientation to be machined. The following rules ranked in order of priority have been considered to assign machining workingsteps related to rotated features to the ultimate setups: 1. assign a rotated feature workingstep to the setup which ensures the minimum tilt angle between the feature working direction and the standard placement direction; 2. assign this workingstep to the setup which contains the highest number of features to be processed in order to maximize the number of features to be machined within a setup.

Table 6.2 The sample workpiece setups Standard Standard Placement orientations placement placement direction cosines X

cos(zx) = 1

(a) (b)

X

cos(zx) = 1

(a) (b)

Y

cos(zy) = 1

(c) (d)

Y

cos(zy) = 1

(c) (d)

Z

cos(zz) = 1

(e) (f)

Z

cos(zz) = 1

(e) (f)

cos(xz) = 1(+1); cos(yy) = +1(1) cos(yz) = 1(+1); cos(xy) = 1(+1) cos(xz) = +1(1); cos(yy)= +1(1) cos(yz) = –1(+1); cos(xy)= +1(1) cos(xz) = –1(+1); cos(yx) = 1(+1) cos(yz) = +1(–1); cos(xx) = 1(+1) cos(xz) = 1(+1); cos(yx) = +1(1) cos(yz) = +1(1); cos(xx) = +1(1) cos(xy) = +1(1); cos(yx) = 1(+1) cos(yy) = +1(1); cos(xx) = +1(1) cos(xy) = +1(1); cos(yx) = +1(1) cos(yy) = +1(1); cos(xx) = 1(+1)

Potential setups

Ultimate setups

f1,f2

f1,f2

–

–

–

f1, f2, f3

–

f1, f2, f3

f1, f2, f3

f5

f5

f5

–

f4

f4

f4

–

–

–

–

–


125

It is worth pointing out that the above reported rules are applied if the related workpiece orientation allows to machine the rotated features by means of a 4-axis machine. In general, the same rules are also applied to non-rotated features. With reference to the sample workpiece, features f1 and f2 can be machined by exploiting the X placement direction; however the setups (X-a) and (X-b) are discarded because of the second priority rule reported above. Between the two potential setup configurations for machining f1, f2 and f3, namely (Y-c) and (Y-d), the latter has been preferred because of the workpiece orientation. In fact, features f1 and f2 cannot be machined by a four-axis horizontal machining center using the (Y-c) setup, since the rotary table of a four-axis horizontal machine rotates around the machine y-axis (see Fig. 6.5). If no priority rule is activated, the Setup Planning procedure selects the workpiece orientation after a comparison between the workpiece and the setup face dimensions in order to optimize the amount of workpieces to be clamped onto the fixture face. Thus, the proposed Setup Planning procedure uses the information related to the workpiece in order to generate the setups; at the same time, it also needs the physical pallet geometrical information to maximize the number of workpieces to be located on a setup face. In order to reach an optimal setup face exploitation, it is necessary to develop an algorithm which is able to calculate the maximum number of workpieces to be clamped onto a setup face considering the workpiece orientation, the technological requirements and the priority rules. The Setup Face configuration sub-module performs this task.

6.4.2 Setup Face Configuration The setup face configuration assumes a key role both for the setup planning and the pallet configuration activities. A setup face is defined as a single fixture face related to a specific physical pallet whereon a set of workpieces with identical

Fig. 6.5 (Y-d) and (Y-c) potential setups

126

G. Celano et al.

Fig. 6.6 The fixture face configuration for the sample workpieces

setup are clamped. A setup face also represents a geometrical constraint which involves both workpiece and fixture dimensions. For each setup face the proposed procedure takes into account a tolerance edge Te which encircles the effective working surface; Figure 6.6 shows the working surface and the tolerance edge for such setup face. The setup face working area represents the surface where one or more workpieces can be clamped in accordance to an established setup. In particular, assuming a fixture face as a matrix, the Setup Face Configuration (SFC) procedure computes for each potential setup the number of parts that are clamped along any row (x-direction with respect to the setup face coordinate system) and any column (y-direction with respect to the setup face coordinate system). The configuration must respect the tolerance distance Td between two adjacent workpieces. The Setup Face Configuration procedure places the first part to be machined in correspondence to the left lower corner of the fixture face. Figure 6.6 reports an example of setup face configuration. The first step of the procedure consists of the comparison between the size of the setup face working surface and the area that should be occupied by the workpiece on said setup face. Indeed, the size comparison between setup face and workpiece has to be performed on the basis of the whole set of potential setups, i.e. positions and orientations of the workpiece. The next step of this procedure is the computation of the maximum number of workpieces that can be fixed on a setup face. Finally, if constraints related to rotated features do not exist, the potential setups which ensure an optimal exploitation of the setup face are selected as the ultimate setups. The input and output data used for the algorithm performing the Setup Face Configuration procedure are reported in Tables 6.3 and 6.4, while the overall pseudo code of the procedure is shown in Table 6.5.


127

Table 6.3 Setup face configuration procedure: input parameters Parameter Description hp, bp hf, bf Te Td

Workpiece geometrical dimensions for a given placement Fixture face geometrical dimensions Tolerance edge thickness Tolerance distance between two adjacent workpieces

Table 6.4 Setup face configuration procedure: output parameters Parameter Description Fixture capacity index for any row; Fixture capacity index for any column; Maximum number of workpieces to be clamped;

FCIx FCIy Np

Table 6.5 Setup face configuration procedure: pseudo code Step Step description Step 0

Step 1

Step 2

Calculate the effective fixture working surface: hfe hf 2 Te; f be bf 2 Te; Dimension comparison: Calculate the maximum effective fixture face dimension: MAX_f; Calculate the minimum effective fixture face dimension: MIN_f; Calculate the maximum workpiece dimension: MAX_p; Calculate the minimum workpiece dimension: MIN_p; If MAX_ p > MAX_ f then refuse the physical pallet; If MAX_ f is along the x-direction then MAX f bfe ; f otherwise MAX f he ; If MIN_ f is along the y-direction then MAX f hfe ; otherwise MAX f bfe ; Calculate Fixture Capacity Index (FCI): If MAX f ¼ b fe then

FCIx ¼

l

MAX f MAX p

If MAX f ¼ hfe then

FCIy ¼ Step 3

l

MAX f MAX p

m

m

; FCIy ¼

; FCIx ¼

l j

m

MIN f MIN p

k

MIN f MIN p

; ;

Calculate Np: If MAX_p FCIx(y) + (FCIx(y) 1) Td MAX_f then NPx = FCIx(y) else NPx = FCIx(y) 1; If MIN_p FCIy(x) + (FCIy(x) 1) Td MIN_f then NPy = FCIy(x) else NPy = FCIy(x) 1; NP= NPx NPy;

128

G. Celano et al.

6.4.3 Tool Path and Rapid Movements In accordance with the ISO 14649 standard a workplan determines the final order of operations to be executed on a part: thus, since the first element in a workplan needs to be a rapid movement, in order to move the tool from its unknown start position to the start point of the first machining operation, an effective process configuration procedure should compute tool paths and rapid times associated with each configured pallet. The final stage of the Setup Planning procedure performs the tool path generation, i.e. an algorithm computes the total rapid feed rate time in relation to an established setup face. If a pallet can be loaded on a particular machine type, then the proposed algorithm starts the tool path computation. Since a pallet may be configured with different setup faces and must be loaded on a machine, several one-to-many relationships between a setup face and the machines arise from the tool path generation procedure. For each setup face associated with a machine, the first workpiece programmed in the tool path is the workpiece closer to the setup face left bottom corner, i.e. closer to the origin of setup face coordinate system. A different tool path should be defined for each feature of the workpieces clamped on the setup face. In Fig. 6.7 an example of tool path is plotted: it starts from the standby tool position and it visits the same feature f3 for all the parts clamped on the setup face. Once the feature position related to the first workpiece has been detected on the setup face, the procedure is able to compute the distances along the x, y and z-directions that the tool has to cover moving from the standby position to the feature. The second part of the tool path computation regards the distance to be covered passing from a workpiece to another located along the same row or along the same column. The procedure considers the setup face as a grid and carries out a tool path which runs on consecutive rows, as reported in Fig. 6.7. Finally, the third part of the tool path brings it back to the standby position. As the overall tool path is determined, this information can be matched with the machine kinematics parameters (rapid feed rate speed and acceleration) to calculate the tool rapid feed rate times related to a setup face.

Fig. 6.7 The tool path definition for a setup face with 2 rows and 2 columns


129

6.5 Pallet Configuration The Pallet Configuration procedure addresses the setup sequencing problem. A pallet type is defined by the information on the physical pallet and by the combination of its setup faces. Since for a given workpiece the relation between a physical pallet and its setup faces is one-to-many, an algorithm is required to generate the whole set of alternative pallet type configurations defined as combination of setup faces. In order to better explain the approach proposed to solve the pallet configuration problem, the analysis is referred to the sample workpiece previously introduced (Fig. 6.3). The following assumptions hold: (i) three types of physical pallets (PP01, PP02 and PP03) can be selected for the process configuration. Physical pallet PP01 (Angle plate) holds a single fixture face, PP02 (T-fixture) holds two fixture faces and PP03 (Tombstone) holds four fixture faces as described in Fig. 6.8; (ii) the sample workpiece, given the Setup Planning procedure results, can be clamped onto each of the available physical pallets. According to the setup face definition (e.g. a setup face is defined as a single fixture face related to a specific physical pallet whereon a set of workpieces with identical setup are clamped), for each physical pallet exists a one-toone correspondence between setups and setup faces (see Sect. 6.4.2). Thus, for a workpiece which requires three setups there will be three distinct setup faces (e.g. A, B and C) for each physical pallet. Considering the combination of three setup faces and the three physical pallets (e.g. PP01, PP02 and PP03) a total amount of 9 setup faces can be identified: 1. PP01_A, PP01_B, PP01_C 2. PP02_A, PP02_B, PP02_C 3. PP03_A, PP03_B, PP03_C Thus, each term of the above reported triplets represents a setup face related to a physical pallet. The Pallet Configuration procedure (PC) generates the whole set of setup face combinations by assigning a setup face to a specific (a)

(b)

(c)

Fig. 6.8 The available physical pallets: (a) Angle plate, (b) T-fixture, (c) Tombstone

130

G. Celano et al.

fixture face of a physical pallet. As reported in Sect. 6.3.2, a constraint assigns the same setup face to the symmetrical fixture faces of the pallets. For example, referring to the PP03 tombstone physical pallet characterized by four fixture faces, the Pallet Configuration procedure can configure the following combinations of setup faces: 1. 2. 3. 4. 5. 6.

PP03_A – PP03_A PP03_B – PP03_B PP03_C – PP03_C PP03_A – PP03_B PP03_B – PP03_C PP03_A – PP03_C

Since each physical pallet has to be configured assuming a symmetrical fixture face configuration, the ‘‘PP03_A – PP03_B’’ solution means that the tombstone will be configured with two PP03_A setup faces and two PP03_B setup faces (e.g. see Fig. 6.9). The setup face combinations reported above are equivalent to the following six pallet configurations: 1. 2. 3. 4.

PP03_1: 4 (2+2) fixture faces arranged as setup face PP03_A. PP03_2: 4 (2+2) fixture faces arranged as setup face PP03_B. PP03_3: 4 (2+2) fixture faces arranged as setup face PP03_C. PP03_4: 2 fixture faces arranged as setup face PP03_A + 2 faces arranged as setup face PP03_B. 5. PP03_5: 2 fixture faces arranged as setup face PP03_B + 2 faces arranged as setup face PP03_C. 6. PP03_6: 2 fixture faces arranged as setup face PP03_A + 2 faces arranged as setup face PP03_C. The total number of combinations depends on the number of workpiece setups and on the number of fixture faces available on the physical pallet, as reported in Table 6.6; the value reported between parenthesis means that only for a workpiece with four expected setup faces it is possible to configure a tombstone where each face is characterized by a different setup. After the whole

Fig. 6.9 Pallet PP03 configured with 2 setup faces A and 2 setup faces B (i.e. PP03_4)


131

Table 6.6 The maximum number of setup face combinations for each physical pallet Physical pallet Workpiece Type Fixture faces 3 setups 4 setups 5 setups 6 setups PP01 PP02 PP03

1 2 4

3 6 6

4 10 10(11)

5 15 15

6 21 21

set of alternative pallets has been configured, it is necessary to define the alternative process plans by sequencing setups while respecting the precedence constraints among the machining workingsteps.

6.6 Setup Sequencing The final step of the ‘‘Mapping Requirements on Devices’’ procedure concerns the setup sequencing. Indeed, in this study the setup sequencing task is interpreted as the selection of a workplan resulting from a ‘‘pallet sequencing’’ activity which takes into account the precedence relations among the different pallets. Indeed, one or more technological precedence relations may occur among workingsteps within the same pallet (i.e. among workingsteps assigned to the same setup face), or among workingsteps assigned to different pallets. Precedence constraints among workingsteps assigned to the same pallet can be directly managed during the part program development and do not influence the workplan generation. On the contrary, precedence constraints among the workingsteps belonging to different pallets should be considered as an active constraint of the problem: thus, the main task of the Setup Sequencing procedure consists of generating alternative sequences of pallets which satisfy these precedence constraints. The feasible sequences of pallets provided by the Setup Sequencing procedure represent distinct process plans that can be defined as ‘‘workplans’’, in accordance to the STEP-NC standard. The input data of the procedure implemented to solve the Setup Sequencing problem have been introduced in Table 6.7, while the output data consist of the sequence of pallets; the pseudo code related to the algorithm is described in Table 6.8. The sequencing algorithm runs a heuristic procedure that works by means of a random search for a limited number of iterations selected a priori by the user. To better describe how the setup sequencing procedure works, Table 6.9 summarizes the main information provided for the setup sequencing of the sample workpiece; in particular, the physical pallets PP02 (T-fixture) and PP03 Table 6.7 Pallet sequence generation procedure: input data Parameter Description n_sf n_sf_max

Number of different setup faces allocated to a pallet Max number of different setup faces allowed within a sequence

132

G. Celano et al.

Table 6.8 Pallet sequence generation procedure: pseudo code Step Step description Step 1

Step 2 Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Workplan generation procedure – mapping setup faces on pallets: for each pallet, its setup faces and the number of equal setup faces are identified by a relation table between the setup face and the pallet Mapping setups on setup faces: for each setup face, its corresponding workpiece setup is identified Mapping workingsteps on setup face: for each expected workpiece setup (which is also referred to a proper Standard Placement Direction), the workingsteps to be machined through that setup are individuated Pallet grouping: all the pallets which hold workpieces with the same setup represents a ‘‘pallet group’’ Workplan generation: A random search procedure generates sequences of pallet groups until the machining precedence relations existing among the workingsteps related to the setup faces allocated to those pallets are satisfied. At the end of the procedure, an ordered sequence of pallet groups are available for further elaborations together with a feasible workplan of machining workingsteps Pallet sequencing procedure – first pallet selection: g = 1; a pallet of the first pallet group (g = 1) is randomly selected as the first element of the pallet sequence. g = g+1, n_sf = 1 (if the selected pallet holds a single setup face); n_sf = 2 (if the selected pallet holds two distinct setup faces); n_sf = 4 (if the selected pallet holds 4 distinct setup faces and the workpiece needs only four setups) Additional pallet selection: if n_sf = n_sf_max then the pallet sequence has been generated, go to step 10, otherwise a pallet of the g-th pallet group is randomly selected as an additional element of the pallet sequence Setup face check: if the selected pallet is already included within the before g1 selected pallets, then go to step 7, else accept the pallet: g = g+1, n_sf = n_sf + 1 (if the selected pallet holds a single setup face); n_sf = n_sf + 2 (if the selected pallet holds two distinct setup faces); n_sf = n_sf + 4 (if the selected pallet holds 4 distinct setup faces and the workpiece needs only four setups) Sequence closing: if n_sf = n_sf_max then the pallet sequence has been generated, exit; else go to step 7

(tombstone) have been considered to illustrate this example of a pallet sequencing problem. Each row of the Table 6.9 refers to a pallet group; as stated before, each pallet group is related to an expected setup and to the workingsteps (WS) to be machined within that setup. The column named ‘‘setup’’ reports both the workpiece placement related information in terms of Standard Placement


133

Table 6.9 The setup sequencing for the sample workpiece: the pallet grouping Group Setup Workingsteps Setup faces Pallet Identical setup faces 1

Y SPD

WS1, WS2, WS3

sf1 (=sf4)

PP02_1 PP02_4 PP02_6 PP03_1 PP03_4 PP03_6

2 1 1 4 2 2

WS5

sf2 (=sf5)

PP02_2 PP02_4 PP02_5 PP03_2 PP03_4 PP03_5

2 1 1 4 2 2

WS4

sf3 (=sf6)

PP02_5 PP02_3 PP02_5 PP02_6 PP03_3 PP03_5 PP03_6

2 2 1 1 4 2 2

cos(zy) = +1 cos(yz) = +1 cos(xx) = 1 2

Y SPD cos(zy) = 1 cos(xy) = +1 cos(yx) = 1

3

Z SPD cos(zz) = +1 cos(xz) = +1 cos(yx) = 1

Direction (SPD) and the specific workpiece placement orientation in terms of direction cosines. The sample workpiece may be clamped with the same setup on the fixture faces of either the pallets PP02 and PP03: in fact, the three setup faces generated by the Setup Planning procedure can be assigned equivalently to the PP02 or the PP03 physical pallet; this means that the setup faces sf1, sf2 and sf3 are equivalent to the setup faces sf4, sf5 and sf6. The Pallet Configuration procedure designs pallets making full use of the provided setup faces, so it is possible to have different pallets configured with the same setup face. The last column of Table 6.9 takes into account the number of identical setup faces expected for each configured pallet. For example, the tombstone pallet PP03_4 is configured with two setup faces A and two setup faces B, i.e. there are two couples of symmetrical fixture faces. Furthermore, the T-fixture pallet PP02_6 has one setup face A and one setup face C. Regardless of the precedence constraint existing among machining workingsteps belonging to different pallets, the pallet sequencing procedure generates effective pallets sequences as follows:

PP02_1, PP03_2, PP03_3; PP03_1, PP03_2, PP03_3; PP03_1, PP03_5; ... PP03_6, PP03_2.

134

G. Celano et al.

Then, in order to provide feasible pallet sequences just one pallet can hold the same setup face within a setup sequence: this means, for example, that the sequence PP02_1, PP03_4, PP02_3 should be declared as unfeasible because the setup face A would be included both in pallet type PP02_1 and pallet type PP03_4. Although the number of expected setups for the sample workpiece is three, the pallet sequencing procedure may generate a sequence with a smaller number of elements due to the possibility of assigning different setup faces to the same pallet type. Finally, the pallet sequencing task can be considered as a double constrained permutation problem. In fact, the Pallet Sequencing procedure is able to find out feasible sequences of pallets respecting the following constraints: the precedence constraints among workingsteps which belong to different pallets and the setup face constraint which avoids duplicating any setup face on different pallets within a sequence.

6.7 Conclusions This chapter has presented the ‘‘Mapping Requirement on Devices’’ procedure which consists of three interrelated modules: the ‘‘Setup Planning’’, the ‘‘Pallet Configuration’’ and the ‘‘Setup Sequencing’’ modules. The Setup Planning module maps the workpiece on physical fixtures in order to find out the optimal setups. The Pallet configuration module couples the setup faces with the physical pallets and the physical pallets with the machines: the output is a set of available pallets. Finally, the Setup Sequencing module generates a set of feasible workplans modeled as sequences of pallets to be loaded on the CNC machine. A detailed description of the ‘‘Mapping Requirement on Devices’’ procedure has been presented throughout the chapter with reference to a sample part to be machined. The ‘‘Mapping Requirement on Devices’’ procedure which has been presented in this Chapter gives a research contribution in the fields of fixture selection/ design and part modeling, positioning and orientation with reference to a ‘‘multisetup’’ fixture configuration. In fact, in most of the literature the setup planning problem has been approached only by analyzing a single workpiece to be machined at a time. The proposed setup planning procedure performs a fixture face configuration wherein more than a part can be machined. Both multi-setup fixture configuration and setup generation have been integrated in a unique setup planning tool which takes into account only a well-defined set of potential setups for a part to be machined, while exploiting the workpiece envelope cube for defining its placement and its orientation on a fixture device. In addition, since the setup sequencing problem is also affected by the multisetup fixture configuration, an innovative approach has been proposed for solving the combinatorial constrained problem associated with the generation of feasible sequences of pallets. Beyond what has been presented in this chapter, the research on process planning could address other important topics:


135

The setup planning problem can be enhanced by assuming that the same feature can be processed by different operations and by means of different machining directions. As a consequence, the selection of alternative workingsteps would require an optimization procedure to minimize the number of setups needed by a given part, also enhancing the performance of the overall dynamic decision-making approach. The possibility to mount different part types on the same pallet fixture, in order to evaluate the tool change times impact on the overall pallet processing time. In order to enlarge the solution space in terms of alternative process plans, more orientations of the part could be considered whenever it is located on a fixture face; this strategy can be more interesting if machining centers equipped with multiple spindles or multiple tables are taken into account. In this case, significant effects should be primarily produced on the pallet configuration issue. Due to the high complexity of the setup sequencing problem in terms of combinatorial computation, additional and more efficient heuristic procedures could be developed and tested on the problem.

References Cai N, Wang L, Feng H-Y (2008) Adaptive setup planning of prismatic parts for machine tools with varying configurations. Int J Prod Res 45(3):571–594 Contini P, Tolio T (2004) Computer aided setup planning for machining centers configuration. Int J Prod Res 42/17:3473–3491 Hebbal S-S, Mehta N-K (2007) Setup planning for machining features of prismatic parts. Int J Prod Res, iFirst: 1–17 ISO/FDIS 14649-10 (2002) Data model for computerized numerical controllers, general process data, ISO/TC 184/SC1/WG7 N 322 Liu W, Peng G (2005) An internet-enabled setup planning system. Proceeding of the third international conference on information technology and application (ICTTA’05), 4–7 July, vol. 2, pp 89–92 Peng G, Liu W, Zhang X (2005) An Internet-based system for setup planning in machining operations. Proceedings of the 10th IEEE International Conference in Engineering of complex Computer Systems (ICECCS), 16–20 June, pp: 245–251 Wang J, Luh P B (1996) Scheduling of a machining center. Math Comput Model 23: 203–214. Yao S, Han X, Yang, Y, Rong Y, Huang S, Yen D, Zhang G (2007a) Computer aided manufacturing planning for mass customization: part 1, framework. Int J Adv Manuf Technol 32:194–204 Yao S, Han X, Yang Y, Rong Y, Huang S, Yen D, Zhang G (2007b) Computer aided manufacturing planning for mass customization: part 2, automated setup planning. Int J Adv Manuf Technol 32:205–217 Zhang H-C, Lin E (1999) A hybrid-graph approach for automated setup planning in CAPP. Robot Com-Int Manuf 15:89–100 Zhang Y, Peng G (2005) Development of an integrated system for setup planning and fixture design in CAPP. Proceeding of the 2005 IEEE/ASME international conference on advanced intelligent mechatronics, Monterey, California, USA, 24–28 July, pp 1401–1406

Chapter 7

Design of Focused Flexibility Manufacturing Systems (FFMSs) Walter Terkaj, Tullio Tolio and Anna Valente

Abstract Manufacturing systems design must provide effective solutions to cope with the demand during the whole system life-cycle. The problem consists of selecting the appropriate set of resources which best fits the requirements of the addressed production problem. When the demand is characterized by a family of products undergoing technological and volume modifications, the system design process becomes quite complicated. Starting from present and forecasted information, machine tool builders have to design systems endowed with the flexibility and reconfigurability levels that enable the system to face the production problem variability during its life. In spite of the relevance of this topic, there is a lack of tools to explicitly design system flexibility and reconfigurability considering the uncertainty affecting the problem. By addressing two main types of uncertainty, i.e. demand variability and resource availability, this chapter presents a solution method based on multi-stage stochastic programming, to support the design of new manufacturing system architectures whose level of flexibility is focused on the specific production requirements. The problem variability is modeled through scenario trees and the solution is a capacity plan with an initial system configuration and possible reconfigurations. Testing experiments have been carried out considering an industrial case to study the benefits that this approach can offer to machine tool builders. Keywords Manufacturing system design Focused Flexibility Manufacturing Systems – FFMS Stochastic programming

7.1 Introduction Manufacturing system design is a highly critical task because it entails the consideration of different criteria related to economy, finance, technology, management, customer satisfaction and human resources involving both W. Terkaj (*) Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy e-mail: [email protected]


137

138

W. Terkaj et al.

quantitative and qualitative aspects, as highlighted by Manassero et al. (2004). Moreover, the impact of external uncertainty (e.g. demand volumes and technological characteristics of the products) and internal uncertainty (e.g. resource availability) should be taken into account during the design phase. As a consequence, the manufacturing system design problem must refer to a planning horizon embracing the whole system life-cycle. As introduced in Chap. 1, the problem of manufacturing system design is addressed both by machine tool builders and system users. The task of the machine tool builder is to identify a set of alternative system configurations which fit the production requirements with different cost and performance. The system user evaluates the alternative system configurations and defines the timing of acquisition of the resources, thus planning its system life-cycle (see Chap. 8). Even if the design of the whole system life-cycle complicates the problem, it represents an opportunity for the machine tool builders. Indeed, future system reconfigurations are a revenue option that machine tool builders should analyze when preparing an offer that can be profitable not only at the time of installation but also in the long-term. In this chapter the analysis focuses on the design activity carried out by the machine tool builder who has to select the set of resources to cope with the production problem of his potential client. As a consequence, in this chapter the system designer corresponds to the machine tool builder. During the design process, production variability and uncertainty are typically handled by enhancing the flexibility degree of production systems. However, even if system flexibility is often judged as a fundamental requirement for firms, it is not always a desirable characteristic because it requires relevant investments which can deeply impact on the firm profitability. Indeed, an analysis of industrial cases highlights that system flexibility is not always essential (Matta et al. 2001). For instance, production problems characterized by mid-high demand volumes of a low variety of products which undergo few modifications should be faced by production systems that do not require the highest level of flexibility. The system flexibility should be customized on the production requirements, aiming at the optimal trade-off between productivity and flexibility. The strategy of customizing system characteristics on present and forecasted production requirements gives an advantage to system users because it is possible to reduce the investment effort thus increasing the profitability. Focusing the system flexibility offers advantages to machine tool builders as well, because the competitiveness can be increased by offering innovative and cost effective solutions. Production systems that give an answer to the need of customizing the system characteristics on the production requirements belong to the class of Focused Flexibility Manufacturing Systems – FFMSs (see Chap. 1). This new class of manufacturing systems allows to answer to the production problem by guaranteeing the optimal trade-off between productivity and flexibility (Ganzi and Tolio 2003; Tolio and Valente 2007; Cantamessa et al. 2007; Tolio et al. 2007). Information about the required level of system flexibility can be

7 Design of Focused Flexibility Manufacturing Systems

139

exploited both by machine tool builders, when generating a bid, and by system users, when evaluating bids. However, it must be noted that these two actors can have different objective functions and therefore their optimal solutions could not coincide. Indeed, a machine tool builder aims at maximizing his profit when selling a system, while a system user aims at minimizing the investment cost (Terkaj and Tolio 2007). The complexity of the system design process suggests the need of decision support tools to tackle the previous issues and to make this activity more efficient and effective (Matta et al. 2005). A higher efficiency is obtained because it is possible to explore a wider range of system solutions, while a higher effectiveness is reached because the machine tool builder can increase its expected profit. Moreover, a formalized approach to system design can help a machine tool builder to quantitatively justify the configuration decisions, i.e. the selection of particular resource types. On the basis of these observations, this chapter proposes a model to design FFMSs consisting of CNC machine tools with automated material handling devices by considering both economic and technological issues. However, this approach can be easily extended to others Automated Manufacturing Systems (e.g. Flexible Transfer Lines, Flexible Manufacturing Systems, Reconfigurable Manufacturing Systems, etc.). The proposed design model aims at defining a plan with an initial system configuration and future reconfigurations to cope with the changes affecting the external and internal environment. Uncertainty related to these changes will be modeled by means of a stochastic programming approach. The content of this chapter is structured as follows. The next section presents a literature review on the manufacturing system design topic. The problem statement is formulated in Sect. 7.3. The system design approach is introduced in Sect. 7.4, while Sects. 7.5, 7.6, 7.7 and 7.8 present different system design models that aim at considering different issues. Section 7.9 provides the results of the testing activities. Finally, Sect. 7.10 provides concluding remarks and future developments of the whole system design approach.

7.2 Literature Review As anticipated in the introduction, manufacturing system design represents a complex task since it deals with many different aspects. This explains the lack of methodologies which allow to jointly consider its different sub-problems at the same time. A literature review of the papers addressing the topic of manufacturing system design has already been presented in Chaps. 1 and 3, paying attention to manufacturing systems endowed with flexibility. In this section the focus is on system design methodologies and in particular on those papers that present methods belonging to two main research areas: capacity planning methods and manufacturing system design methods performing a technological analysis both of the production problems and of the system resources.

140

W. Terkaj et al.

Regarding the capacity planning methods, Matta et al. (2001) provided a framework to design Advanced Manufacturing Systems capacity taking in consideration different factors such as firm strategy, market uncertainty, uncertainty regarding competitor strategies, available system architectures and types of technologies. The capacity planning problem has been also addressed by Asl and Ulsoy (2002, 2003) who presented an optimal policy for the capacity management problem. They provided a model which considers both capacity expansion and reduction problems adopting the Markov decision theory. Recently, Matta et al. (2008) presented an evolution of the approach by Asl and Ulsoy (2003) where the effect of the ramp-up phenomenon is explicitly modeled; the authors have proved that ignoring the ramp-up effect in the decision process can significantly increase the overall costs. Amico et al. (2006) proposed a capacity planning model for Reconfigurable Manufacturing Systems (RMSs) modeling the investment decisions through the joint application of the Discounted Cash Flow (DCF) and the Real Options Analysis (ROA) techniques. Deif and ElMaraghy (2006) developed a Genetic Algorithm (GA) technique for generating an optimal capacity schedule for RMSs; the capacity level and the cost of the capacity schedule of RMSs are related to the cost of system reconfigurations. Thus, the cost-effective implementation of RMSs relies on decreasing the cost of system reconfigurations. The problem of evaluating the impact of technological issues on the system design has been addressed by Shin et al. (1997) who proposed a decision support model for the design of Flexible Manufacturing Systems, with the goal of maximizing the profit of the system. The authors highlighted that in many system design approaches the part types to be produced are considered as given; then, this input information is used to determine an optimal system configuration. However, more realistic solutions can be obtained when the interaction between candidate part types and configurations are explicitly modeled. Park et al. (2001) addressed the problem of FMS design developing a hybrid approach by (1) simultaneously considering design and operational parameters, (2) modeling performance measures of the FMS using design of experiments and regression analysis, and then (3) achieving optimal levels of multiple performance measures through a compromise programming problem. These two main research areas have been rarely merged by developing integrated design methods that jointly consider technological and demand information. Ganzi and Tolio (2003) proposed a system design method that provides as output manufacturing system configurations whose level of productivity and flexibility is tuned on the production needs of the firm. The developed approach starts from a detailed analysis of technological and demand data. At first, the part mix is analyzed to define clusters of machining operations that require machine tools with the same technological and functional characteristics. Then, the information content of each cluster is used to solve the system configuration/reconfiguration problem. The design problem becomes even more complex if the manufacturing system must be designed to cope with changes of production requirements, taking into account both


141

present and future production problems. This topic has been addressed by Tolio and Valente (2006, 2007, 2008) who introduce the concept of focused flexibility in manufacturing. The authors have shown that the breadth and diversity of the selectable resources have an important impact on the expected profitability of the designed systems. Indeed, a rich resource catalogue gives to the system designer much more options to answer to the production requirements in a cost-effective way. The same authors developed a design framework that, starting from the production problem analysis and formalization, gives as output the number and type of resources that are needed to face the present and forecasted production requirements.

7.3 Problem Statement The FFMS design problem represents the central topic of the manufacturing system design framework presented in Chap. 1 by means of IDEF0 diagrams. As anticipated in the introduction of this chapter, herein the activity of system design is carried out by machine tool builders, keeping as reference the double design perspective of the machine tool builder and of the system user (see Sect. 1.5). The manufacturing system design problem consists of selecting the best set of resources to satisfy the production requirements during the whole system lifecycle with the maximum expected profit. Since Automated Manufacturing Systems (AMSs) and in particular FFMSs are considered, the resources consist of CNC machine tools, transporters, load/unload stations, pallets and tools. In particular this book focuses on systems producing prismatic components which can be loaded on pallets to be machined on CNC machines. Pallets are assumed to be easily moveable among machines by proper automated transport systems. The cost of the resources which can be selected in the design phase depends on their architecture and their performance. The system design process can start from green field or can regard an existing production system. In the first case, the whole set of resources must be purchased. In the second case, it could be necessary to purchase just a subset of the required devices and to integrate new resources within the existing system. The tooling system configuration problem is not considered in this book since this activity can be addressed at a lower level in the system design hierarchy. Therefore the FFMS design model presented in the following sections does not select the number and type of tools. For an analysis of the tooling system configuration problem please refer to Grieco et al. (1995), Colosimo et al. (2002), Matta et al. (2004) and Buyurgana et al. (2004). Besides the set of selectable resources, the machine tool builder needs information about the demand and the feasible process plans to machine the products. In particular, the demand is characterized by a set of products with their demand volumes and technological features. Volumes and product features

142

W. Terkaj et al.

can evolve over time, e.g. products may be modified, new products can be introduced and demand volume can change. Moreover, demand volumes can also be subject to mid-term variability. Short-term variability is not considered in this work since it mainly impacts on the system management. Information regarding the technological requirements of products to be machined determines the selection of resource types, while information regarding production volumes drives the choice of the number of resources. The modeling of the production problems will be further addressed in Sect. 7.3.1. Process plans are an important input of the system design problem, since they specify how the resources can be used to produce the various part types. It is assumed that such technological analysis has already been carried out so that the machine tool builder can choose from a set of alternative process plans generated considering all the possible resources (Contini and Tolio 2004). Indeed, process planning defines the necessary operations and the setups required to execute the operations. Operations and setups are then assigned to pallets that will be loaded on selected subset of machines. Therefore at system level a process plan can be thought as a sequence of pallets that must be processed to obtain the final product (see Chap. 6). Selected process plans must be tested before starting production by checking if all their operations are properly executed on the assigned machine type. This testing phase has a cost because it reduces the plant capacity and it usually requires the presence of an operator. The output of the FFMS design consists in the selection of resources and process plans to be implemented in a system configuration. Since the production problem evolves over the planning horizon, it can be necessary to properly reconfigure the system. A set of possible reconfigurations can be defined according to the future outcomes of the random variables affecting the problem. Therefore, the output of system design should be a capacity plan with an initial system configuration and a set of possible reconfigurations affecting hardware (e.g. acquisition/dismission of resources) and/or software (e.g. change of process plans) resources of the system.

7.3.1 Modeling of Production Problems The design of evolving manufacturing systems requires a careful study of the production problem over the whole system life-cycle. Present and future information must be taken into account by the decision maker to provide the most efficient system solution. The manufacturing system must be able to react to changes in the production problem; as described in Chap. 1, this reaction can be accomplished by using the already existing characteristics of the system or by adopting system reconfigurations. If reconfigurations are needed, then the system must be endowed with the necessary enablers, e.g. modularity, scalability, etc. (Wiendahl et al. 2007).


143

Production problems can be considered as a combination of mixes of products that evolve during the observed horizon. The evolution of the products depends both on the market requirements and on the company strategy (Tolio 2006). The definition of the production problems should be as precise as possible because it deeply impacts on the system design activity. Since managing information in an evolutionary perspective can be quite complex, a scenario tree representation can help to simplify the analysis. The scenario tree adopted in this book (Fig. 7.1) is a directed graph composed of nodes representing the outcomes of a set of random variables defining the production problem characteristics. Each level of the scenario tree represents a time period (e.g. six months, one year, etc.). Each node contains the information associated with a certain time period and it is characterized by a unique parent node and by a realization probability. A sequence of linked nodes in the tree models the information evolution along the planning horizon. Each path from the root node to a leaf node in the last time period identifies a scenario. In Fig. 7.1, scenario nodes are represented as circles; in particular, nodes of Scenario 1 are enclosed by a dashed rectangle, while nodes of Period 2 are enclosed by a dotted oval. The scenario nodes are positioned at the beginning of the time period that they are representing. Moreover, a single node could be composed of many short/mid-term (e.g. daily, weekly or monthly) production problems. For instance, subcontractors must produce in the same system components which are sold to different customers with different due dates, so that the system usually does not face the same production problem every day. Therefore each scenario contains one ore more short/mid-term production problems which are represented as dotted circles in Fig. 7.2. Chapter 4 has already provided a detailed description and formalization of the scenario tree (Sect. 4.4). Short- and mid-term production problems characterizing the demand can be simplified through a mathematical analysis. Indeed production problems inside each scenario node can be encompassed by a convex polyhedron as represented in Fig. 7.3, where the axes of the diagram represent the quantities of the two product types (product A and product B) composing the part family. A system

Fig. 7.1 Scenario tree representation

144

W. Terkaj et al.

Fig. 7.2 Extended Scenario tree representation

Fig. 7.3 Production problem analysis and simplification

that is able to cope with the production problems at the vertex of the polyhedron can also face all the production problems inside the polyhedron. Therefore, by evaluating only production problems at the vertex of the polyhedron it is possible to simplify the system design problem. The generation of a scenario tree for the problem of manufacturing system design and its link with the manufacturing strategy is addressed in Chap. 5 of this book. Depending on how the production problem variability has been modeled, different system design models can be developed as it will be show in Sects. 7.4.1 and 7.5.

7.4 System Design Approach Terkaj et al. (2008) have suggested that a complete system design approach should be developed taking in consideration the Basic Flexibility Levels (i.e. Flexibility, Reconfigurability and Changeability) and Basic Flexibility


145

Dimensions (i.e. Capacity, Functionality, Process, Production Planning) which have already been described in Chap. 3. Levels and dimensions can help to define the constraints that match the requirements of the production problems with the selectable resources. A manufacturing system design approach considering the Basic Flexibility Levels must be able to:

model both the dynamicity and stochasticity of product life-cycle and use this information as input of the system design model;

plan the system life-cycle, thus defining the initial system configuration and possible future reconfigurations. Therefore, it is necessary to clearly separate the configuration decisions which must be taken immediately from those which can be taken later. These issues can be fully addressed adopting the stochastic programming technique (Birge and Louveaux 1997). The application of this technique is presented in Sect. 7.4.1. The FFMS design approach addresses a set of issues that can be defined and grouped according to the Basic Flexibility Dimensions. The Process issues deal with:

the choice of the process plans among a set of alternatives; the validation of new process plans; precedence and tolerance constraints among the operations. The FFMS design approach has to model also Functionality issues such as:

the assignment of the operation types to the selected resource types; the assignment of the pallet types to the selected resource types. Finally, the FFMS design approach has to address the following issues that are related to the Capacity of the manufacturing system:

modeling of resource capacity and resource usage by the operations. The resource types are machine, carrier, load/unload station and pallet;

possible reductions in the availability of the resources; modeling the shortfall production of the system. The resource selection and the operation assignment problems are strictly related in the case of FFMS design. Therefore it is necessary to integrate these aspects in order to obtain effective system solutions. All the issues previously described have been addressed by the proposed system design methodology through the formulation of proper constraints (see Sect. 7.6.3). Acting on the constraints it is possible to implicitly define the flexibility embedded in the system. The constraints have been developed according to some assumptions regarding products, processes, resources and economic issues that are detailed in Sect. 7.4.2. Finally, the manufacturing system design approach must be able to use all the relevant input information and provide as output the necessary data. The

146

W. Terkaj et al.

specification of the input and output information of the FFMS design approach are described in Sects. 7.4.3 and 7.4.4, respectively.

7.4.1 Stochastic Programming A production system designed considering a deterministic environment can yield a lower performance than what is expected because of the uncertainty affecting the production environment. Stochastic programming (Birge and Louveaux 1997) can be used to develop a system design model addressing the topic of co-evolution of production problems and production systems. Indeed stochastic programming allows to model uncertainty using a scenario tree approach. The same methodology takes into account that initial decisions can be modified by future recourse actions according to the realizations of the different scenarios. Therefore a stochastic programming approach can exploit the definition of production problems through scenario trees and gives as output the system configurations and reconfigurations by defining different decision stages. When a stochastic programming model is solved, the expectation of an objective function is optimized against the considered realizations of the random variables, while respecting a set of constraints. Therefore, initial decisions are followed by observations of uncertain parameters which are gradually revealed over time. The evolution of the products is modeled by means of the scenario tree that has been described in Sect. 7.3.1. When stochastic programming is adopted to solve a stochastic problem modeled with a scenario tree, then it is possible to formulate also a decision tree. The number of stages which are considered in the decision tree can be different from those of the scenario tree and this means, in the case of system design, that the decision maker can model the availability of system reconfiguration options in one or more periods. Depending on the number of times that the decision maker can revise the designed system solution, it is possible to model single-, two- or multi-stage problems. In a single-stage design model all the decisions must be taken at the beginning of the planning horizon. In particular, a single-stage formulation leads to determine a system configuration which is able to cope with the whole set of production problems, both present and future (see Sect. 7.5). This means to take a single decision in order to face the input scenario tree, as illustrated in Fig. 7.4 where the decision node is represented as a striped circle. A two-stage stochastic formulation of the FFMS design approach (see Sect. 7.5) allows to model the reconfiguration of the manufacturing system during a future time stage. The initial system configuration is designed taking into account both the deterministic data related to the present production problem and the data related to the production problems that can occur in the future. This decision is applied ‘‘Here&Now’’ and is equal for all the forecasted scenarios.


147

Fig. 7.4 Single-stage decision

When information about future production problems is disclosed, then the system designer can take recourse actions to cope with the changes in the environment. In a two-stage stochastic programming model all these recourse decision are explicitly defined and each scenario has a different optimal second stage solution. In Fig. 7.5 the decision nodes are represented again as striped circles, while the nodes of the scenario tree as full circles; the second stage decisions (i.e. system reconfiguration decisions) are implemented only after the disclosure of the stochastic information about future time periods. If compared to the single-stage formulation, a two-stage model provides more efficient system solutions since the decision maker has the opportunity

Fig. 7.5 Two-stage decision tree

148

W. Terkaj et al.

to customize the system configuration on the real production requirements. The two-stage decision procedure can be applied over a long time horizon through a rolling approach. In this case, as soon as the stochastic information is disclosed, the two-stage model is launched again shifting the planning horizon by one period and considering as given the system configuration previously obtained. Therefore the second stage solutions can be considered as reconfiguration options since they will not be necessarily implemented. In Fig. 7.6 the second stage corresponds to the first stage of the new system design problem that is launched after the disclosure of the stochastic information. In a multi-stage formulation the decision variables are divided into different time stages (see Sect. 7.6). The correspondence between the nodes of the general scenario tree (Fig. 7.1) and the nodes of the decision tree (Fig. 7.7) is at most one-to-one: indeed it could happen that the number of decision tree stages is lower than the number of stages of the considered scenario tree and/or some nodes of the decision tree are aggregated when building the decision tree. Decision variables associated with a stage are replicated for every node belonging to that stage. In a multi-stage approach it is possible to model all the system reconfiguration options that can be implemented when the actual production information is disclosed. A multiple decision formulation represents the most complete technique in production contexts characterized by frequent changes since it guarantees a

Fig. 7.6 Two-stage approach with rolling horizon


149

Fig. 7.7 Multi-stage decision tree

precise modeling of the future evolutions and of the way to cope with them. However, stochastic programming models can require a significant computational effort. To face this issue some algorithms have been developed to decompose the problem and solve it in a more efficient way (Laporte and Loveaux 1993; Sen and Higle 2005; Sen and Sherali 2006).

7.4.2 Assumptions The system design approach that is proposed in this book can be applied to the general domain of Automated Manufacturing Systems. However, the system design models presented in this chapter have been developed paying attention to the particular case of Focused Flexibility Manufacturing Systems (FFMSs). The FFMS design models presented in the next sections have been developed adopting the following assumptions about products, processes, resources, economic issues and boundary conditions. The assumptions related to the products are:

Long-term variability and evolution of the demand of the products is modeled by means of a scenario tree.

Short- and Mid-term variability of the demand is not considered. Therefore the scenario tree modeling the production problem is simplified as reported in Fig. 7.1.

150

W. Terkaj et al.

The assumptions related to the processes are:

The workpieces are mounted on pallets by means of fixtures that have the function of providing stability to parts during the machining operations. The fixtures are usually, but not always, dedicated to a single type of workpiece. The shape and dimensions of the pallets depend on the technological requirements of the type of workpiece and on the characteristics of the machines (e.g. number of axes and working cube). When a process plan is selected for a type of workpiece it is necessary to test the sequence of machining operations in order to fine tune the part programs on the machining centers. This process plan validation and refinement has a cost which is considered in the system design model. The machining operations composing a process plan are subject to precedence and tolerance constraints. This aspect influences the routing and assignment of the pallet types to the machine types. According both to the system architecture and to the pallet configuration, a pallet type can be processed on one or more machine types. For instance, in an FFMS a pallet could be processed by a traditional machining center and by a dedicated machine. The assumptions related to the system resources are:

The selection of the type of transporter is made ex-ante because it is related to strategic decisions about the layout of the manufacturing system. For instance the system designer could choose between a pallet transporter and a part conveyor. In this work it is assumed that there is an automatic pallet transporter (i.e. carrier) in the system: it moves pallets from/to the load/ unload stations, the machines and the pallet buffer. There are automatic or semi-automatic pallet load/unload stations in the system. An alternative option would be to design six-degree-of-freedom clamping robots which load and unload parts between a part conveyor and a fixture equipping the machining center the machining centers. However, this latter option has not been taken into account in the design model. For the sake of simplicity the choice of the type of load/unload station is made ex-ante. This assumption can be easily relaxed with minor changes in the model. The configuration of the tool magazine is not considered in the FFMS design model since it is usually addressed at a lower level in the system design hierarchy. The assumptions related to economic issues and boundary conditions are:

The purchasing cost of the resources is assumed constant over time. This assumption can be relaxed by machine tool builders when applying the model to real problems. In fact, the evolution of the resource prices can be often estimated by machine tool builders, but this information is not spread because of privacy policy. For the same reason, also the selling price of the dismissed resources is assumed to be constant over time.


151

If the manufacturing system is not able to satisfy the demand, then the firm incurs into penalty or outsourcing costs to face the production shortfall.

Cash flows are discounted in order to consider changes in the value of money.

7.4.3 Input Two phases characterize the design approach. The first phase consists of collecting and formalizing information on current and future production problems whereas the second phase deals with the application of design models to the gathered information. The necessary input information of the manufacturing system design problem regards:

the family of products to be machined, in terms of technological characteristics and demand volumes (see Sect. 4.4 and Chap. 5);

how the products can be processed, i.e. the set of (alternative) process plans together with their operations and pallet types required to produce the workpiece types (see Sect. 4.6 and Chap. 6); the set of available resources which can be selected for the designed system (see Sect. 4.5). All these data have been formalized according to the data structure presented in the tables of Chap. 4 to enable the exchange of information among the different modules in the system design architecture (see Chap. 1). Manufacturing system design requires information about all the three areas presented in Chap. 4: product, process and production system. The information about products consists of the set of products (i.e. workpieces; Table 4.1), the technological characteristics of the products (i.e. machining features; Table 4.2), the present and possible future demand volumes (i.e. demand scenarios; Tables 4.3 and 4.4). The information about processes defines how the available and selectable resources can produce the demanded workpiece types. The required data include the machining workingsteps (Table 4.16), the pallet types (Table 4.18) and the process plans (i.e. the workplans; Table 4.17). The information about production systems consists of the current system configuration if the design does not start from green field (Table 4.5). Moreover, it is necessary to describe the set of resources which are in the system or that can be acquired: machining centers (Table 4.8), carriers (Table 4.9), load/ unload stations (Table 4.10), tools (Table 4.11), tool carriers (Table 4.12) and physical pallets (Table 4.13). The set of data concerning the products and processes can be affected by uncertainty. The ability to forecast future changes in terms of technological and production information strongly influences the flexibility level that is designed

152

W. Terkaj et al.

into the system. For instance, limited information regarding future changes can lead to design a system characterized by a high flexibility degree. Conversely, perfect information about future changes allows to customize the degree of flexibility in the system.

7.4.4 Output The main output of the design models consists in the set of resources composing each system configuration. In addition, decisions about process planning must be taken; these decisions link each system configuration with a set of workplans (Table 4.17) and a set of assignments of pallets and machining workingsteps to the selected machining centers. In Sect. 7.3.1 it was shown that the production requirements can be mathematically modeled by the definition of a convex polyhedron representing all the production mixes that could occur. In a similar way, a given system configuration can be characterized by the possible combinations of production volumes that the system can yield. The domain of admissible production volumes can be thought as a n-dimensional space which is bounded by a set of hyperplanes and where the axes correspond to the product quantities. The hyperplanes derive from the capacity constraints which are formulated within a system design model (e.g. see Sect. 7.6.3). The concept of hyperplane has already been introduced in Chap. 4 (Table 4.7). An example of manufacturing system characterization through hyperplanes is shown in Fig. 7.8.a; in this case, the space is 3-dimensional since there are three part types in the part family (i.e. Product A, Product B and Product C). The manufacturing system consists of four resources (i.e. two machines, one carrier and one load/unload station) and each plane is associated with a resource type.

(a)

(b)

Fig. 7.8 (a) Hyperplanes bounding the admissible domain (b) Admissible domain of the production system


153

The admissible domain of the production system is the polyhedron (Fig. 7.8.b) bounded by the planes and having the origin of the axes as one of its vertices. Concluding, a manufacturing system can properly address a production problem only if the polyhedron of the admissible domain contains the polyhedron modeling the domain of the possible demand levels.

7.5 FFMS Design Models The system design approach presented in the previous section has been adopted to formulate a set of FFMS design models; these models apply different types of stochastic approach (see Sect. 7.4.1) and meet different requirements of the system designer. This section presents a brief description of the single-stage model (Tolio and Valente 2006) and the two-stage stochastic model (Tolio and Valente 2007), highlighting their key points and possible applications. This should facilitate the understanding of the multi-stage stochastic model (see Sect. 7.6) and its possible extensions (see Sects. 7.7 and 7.8). In the single-stage model (Tolio and Valente 2006) the system designer takes all the decisions at the beginning of the planning horizon. Therefore, the decision maker must select the set of machines, carriers and load/unload stations which are able to satisfy the whole set of possible production problems, while minimizing the investment costs. This particular model could fit the requirements of subcontractors; indeed they typically have to satisfy different production problems with the same production system. Moreover, a singlestage design model could be applied when the system user has partial information about the production problems to be faced in the future but he wants to determine the upper bound, in terms of costs and flexibility, of a system configuration which can meet all the future scenarios (Fig. 7.4). Since the proposed system must be feasible in all the scenarios it is not necessary to estimate their realization probability. The two-stage stochastic formulation of the FFMS design problem has been developed in order to take into account the uncertainty affecting the production information. The complete formulation of the two-stage stochastic programming model is reported in the paper by Tolio and Valente (2007). By analyzing the design problem formulations a dominant feature is the importance of the timing of flexibility acquisition. Indeed, the planning of flexibility acquisition over time represents a key factor especially for companies whose profitability can be jeopardized by high system investment costs. This is why a multi-stage approach (see Sect. 7.6) can offer a better modeling of the problem. However, the advantages related to postponing the investments can be reduced by the need to face more system ramp-ups whose economic impact is not negligible. A system ‘‘Total Cost’’ analysis should be developed to correctly plan the timing of flexibility acquisition (see Sect. 7.7).

154

W. Terkaj et al.

A common feature of all these models is that they aim at minimizing system costs. This choice is mainly related to the need of the machine tool builder to know the optimal configuration of such a production system, i.e. the set of resources which satisfy the production problem with the minimum economic effort. In this sense, the machine tool builder can interpret that solution as a lower bound on which he could start to evaluate his own revenue options. Section 7.8 will present an extension of the multi-stage approach based on the maximization of the expected profit is presented.

7.6 Multi-Stage Stochastic FFMS Design Model The development of a multi-stage stochastic programming model allows to design the whole production system life-cycle taking into consideration uncertain information represented by complex scenario trees (Fig. 7.7). Indeed, a two-stage formulation does not provide competitive solution in production contexts affected by frequent changes over a long horizon. Even if the two-stage formulation can be improved adopting a rolling approach, only a multi-stage approach offers the possibility of jointly modeling all the system changes and the time in which they occur. In the multi-stage stochastic model the system designer starts from the analysis of the scenario tree which represents the evolution of the production problem over the planning horizon. Afterwards he defines the decision tree to cope with the present and forecasted production problems belonging to welldefined time periods. The model gives as output the set of decisions regarding acquisition and dismission of resources (i.e. type and number of machines, transporters, load/ unload stations, pallets) taken in each stage of the decision tree. Moreover, in each stage and for each workpiece a process plan is selected and its operations are assigned to the machine types. The configuration of the system before these decisions is determined by the decisions taken in the previous stage. In this model there is a one-to-one correspondence among nodes in the scenario tree and in the decision tree (Fig. 7.7). The decisions are taken to cope with the outcomes modeled by the associated node of the scenario tree.

7.6.1 Notation and Parameters The sets of elements that are necessary to model the problem together with their notation are reported in Table 7.1. Each set has already been defined in Chap. 4: Scenario Node (Table 4.3), Machine Type (Table 4.8), Workpiece Type (Table 4.1), Workingstep (Table 4.16), Workplan (Table 4.17) and Pallet Type (Table 4.18).


155

Table 7.1 Model notation Index Set z i e w, w1, w2 n p

Scenario Node {1,.., Z} Machine Type {1,..,I} Workpiece Type{1,..,E} Workingstep {1,..,W} Workplan {1,..,N} Pallet Type {1,..,P}

The Scenario Node set consists of all the nodes composing the scenario tree (Fig. 7.1). It is not necessary to introduce a set for modeling also the nodes of the decision tree thanks to the one-to-one correspondence among nodes in the two trees. Indeed, it is possible to refer to a node of the decision tree through the node of the scenario tree where these decisions take place. This assumption allows to simplify the formulation of the model. The Machine Type set consists of all the types of machining centers that can be acquired or that are already available in the present system configuration. The Workpiece Type set is composed of the part types that must be produced in the system to satisfy the demand. A workpiece type requires a set of operations to be produced and all these operations are the elements of the Workingstep set. Indeed, a workingstep (see Sect. 4.6) represents the machining process for a specific feature of the workpiece. The Workplan set consists of all the alternative process plans that can be adopted to machine the considered workpiece types. A workplan is a collection of workingsteps with an execution sequence and in the context of this model it can also be seen as an ordered sequence of pallet types. The pallet types that are necessary to complete the workplans are the elements of the Pallet Type set. The formulation of an FFMS design model requires to consider a wide range of input data that are shown in the following tables. Most of the data can be grouped into three areas, as anticipated in Sect. 7.4.2: product (Table 7.2), process (Table 7.3) and production system (Table 7.4) areas. The remaining data consist of the scenario tree modeling (Table 7.5) and of other generic parameters (Table 7.6). The stochastic data of the problem consist of the demand of workpieces and of the capacity of the resources during the time periods. Table 7.2 Product data Parameter Definition De,z Ewse,w Epe,p mce

Demand of workpieces of type e in scenario node z Equal to 1 if workingstep w is associated with workpiece type e, 0 otherwise Equal to 1 if pallets of type p are used to process workpieces of type e, 0 otherwise Penalty/outsourcing cost for one workpiece of type e

156

W. Terkaj et al.

Table 7.3 Process data Parameter Definition me,n vc Wpn,p Pwsp,w Pmp,i PwsMp,w,i samew1,w2 timep,w,i

Nwsp,w Npartsp Nfp wep

Equal to 1 if workplan n can be chosen to process workpieces of type e, 0 otherwise Cost of workplan validation and refinement Equal to 1 if workplan n requires a pallet of type p, 0 otherwise Equal to 1 if workingstep w can be processed on a pallet of type p, 0 otherwise Equal to 1 if pallets of type p can be loaded on machines of type i, 0 otherwise Equal to 1 if workingstep w can be processed on a pallet of type p when it is loaded on a machine of type i, 0 otherwise Equal to 1 if workingstep w1 and w2 must be processed on the same pallet and on the same machine because of tolerance constraints, 0 otherwise Mean machining time required by machines of type i to process workingstep w when its workpiece is mounted on a pallet of type p. This time takes into account cutting time, rapid movement time and tool change time Number of parts on which the workingstep w can be processed when they are mounted on a pallet of type p Number of parts mounted on a pallet of type p Number of different types of setup face on pallets of type p Workpiece type which is mounted on pallets of type p

Table 7.4 System and resource data Parameter Definition N0i Mmi,z Cmi Cmdi tcpi m i Q0 Mtz Ct Ctd tt t S0 Mlz Cl Cld l T0p Mpp,z Cpp

Number of machines of type i already present in the initial system configuration Time capacity of machines of type i in the planning period associated with scenario node z Investment cost of a machine of type i Residual value of a machine of type i Time to change a pallet on a machine of type i Maintenance coefficient of machines of type i Number of carriers already present in the initial system configuration Time capacity of the carriers in the planning period associated with scenario node z Investment cost of carriers Residual value of carriers Mean transport time for a mission of the carrier Maintenance coefficient of carriers Availability coefficient of carriers Number of load/unload stations already present in the initial system configuration Time capacity of a load/unload station in the planning period associated with scenario node z Investment cost of load/unload stations Residual value of load/unload stations Maintenance coefficient of load/unload stations Number of pallets of type p already present in the initial system configuration Time capacity of pallets of type p in the planning period associated with scenario node z Investment cost for pallets of type p


157

Table 7.4 (continued) Parameter Definition Cpdp tlup

Residual value of pallets of type p Total time required to load/unload all the workpieces on/from a pallet of type p Coefficient which estimates the average increase of the system time of a pallet given the presence of queues Planning coefficient that reduces the availability of the resources due to human factors

Table 7.5 Scenario data Parameter Definition prz stz parz

Realization probability associated with scenario node z Stage of scenario node z {1, 2, 3, . . ..} Parent node of scenario node z

Table 7.6 Model data Parameter Definition r L

Scrap coefficient Discount rate High value constant

7.6.2 Decision Variables According to the multi-stage stochastic programming approach (see Sect. 7.4.1), the decision variables are associated with the nodes belonging to the different time stages. It means that in addition to the decisions taken at the beginning of the planning horizon (i.e. the initial system configuration), it is possible to take additional decisions in subsequent stages (i.e. system reconfigurations). The set of decision variables can be divided into three groups as shown in the following tables. The decision variables related to the cost of the system and the shortfall production are reported in Table 7.7. The decision variables regarding Table 7.7 Cost and shortfall production related decision variables Variable Definition COSTz 2 R MissWp;w;i;z

MissPp;z 2 N Misse;z 2 N

Cost of the system associated with scenario node z Shortfall volume of workingstep w when it should be processed on pallets of type p, loaded on machines of type i in the planning period associated with scenario node z Shortfall volume of pallets of type p in the planning period associated with scenario node z Shortfall/outsourcing volume of workpieces of type e in the planning period associated with scenario node z

158

W. Terkaj et al.

Table 7.8 Process related decision variables Variable Definition xp,i,z 2 {0,1} wpln,z 2 {0,1} newn,z 2 {0,1} xpalp,z 2 {0,1} yp,w,i,z 2 {0,1}

Equal to 1 if pallets of type p must be processed by machines of type i in the planning period associated with scenario node z, 0 otherwise Equal to 1 if workplan n is selected to be processed in the system in the planning period associated with scenario node z, 0 otherwise Equal to 1 if workplan n must be validated before the beginning of the planning period associated with scenario node z, 0 otherwise Equal to 1 if pallets of type p must be processed in the system in the planning period associated with scenario node z, 0 otherwise Equal to 1 if workingstep w is processed on pallets of type p when they are loaded on machines of type i in the planning period associated with scenario node z, 0 otherwise

the process planning are listed in Table 7.8. Finally, the decision variable defining the set of resources in the manufacturing system during the planning horizon are listed in Table 7.9. Table 7.9 Resource related decision variables Variable Definition Ni;z 2 N Sz 2 N Qz 2 N Tp;z 2 N NPi;z 2 N SPz 2 N QPz 2 N TPp;z 2 N NMi;z 2 N SMz 2 N QMz 2 N TMp;z 2 N

Total number of machines of type i in the system in the planning period associated with scenario node z Total number of load/unload stations in the system in the planning period associated with scenario node z Total number of carriers in the system in the planning period associated with scenario node z Total number of pallets of type p in the system in the planning period associated with scenario node z Number of machines of type i acquired before the beginning of the planning period associated with scenario node z Number of load/unload stations acquired before the beginning of the planning period associated with scenario node z Number of carriers acquired before the beginning of the planning period associated with scenario node z Number of pallets of type p acquired before the beginning of the planning period associated with scenario node z Number of machines of type i dismissed before the beginning of the planning period associated with scenario node z Number of load/unload stations dismissed before the beginning of the planning period associated with scenario node z Number of carriers dismissed before the beginning of the planning period associated with scenario node z Number of pallets of type p dismissed before the beginning of the planning period associated with scenario node z


159

7.6.3 Objective Function and Constraints The objective function (7.1) of the model aims at minimizing the expected cost of the manufacturing system during the planning horizon considering all the stochastic data. This expected cost depends on the cost associated with each scenario node (COSTz) which is weighted according to the realization probability of the scenario node z and the discount rate r.

min

Z X COSTz prz z¼1

(7:1)

ð1 þ rÞstz 1

Constraint (7.2) defines how the cost associated with each scenario node z is calculated. The cost consists of the investment cost to acquire the resources; this cost is reduced if some resources are sold. Moreover, the cost is increased when the manufacturing system cannot meet the demand thus incurring in penalty or outsourcing costs. The last term of the cost function takes into account the cost related to the validation of new workplans. ( COSTz ¼

I X

Cmi NPi;z þ Ct QPz þ Cl SPz þ

i¼1

P X

Cpp TPp;z þ

p¼1

( I X

Cmdi NMi;z þ Ctd QMz þ Cld SMz þ

i¼1

þ

)

E X e¼1

mce MISSe;z þ

P X

) Cpdp TMp;z þ (7:2)

p¼1 N X

vc newn;z ;

8z

n¼1

The constraints of the model have been formulated to cope with the issues of the FFMS design approach presented in Sect. 7.4. The constraints are divided into three groups: Process, Functionality and Capacity constraints. This partition is coherent with what Terkaj et al. (2008) have suggested about the design of systems embedding flexibility. Indeed, Process, Functionality, Capacity and Production Planning Flexibility are basic flexibility dimensions (see Sect. 3.1.4) that lead to the definition of the constraints matching the requirements of the production problem with the selectable resources. According to the multi-stage stochastic programming approach, all the constraints of the model are replicated for each scenario node z composing the scenario tree. The group of Process constraints consists of expressions (7.3), (7.4), (7.5), (7.6), (7.7) and (7.8). These constraints deal with the selection of the process plans for all the workpiece types and the satisfaction of tolerance constraints:

160

W. Terkaj et al. N X

wpln;z me;n ¼ 1;

8e; z

(7:3)

n¼1

xpalp;z ¼

X

wpln;z Wpn;p ; 8p; z

(7:4)

n

newn;z ¼ wpln;z ;

8n; z : stz ¼ 1

newn;z wpln;z wpln;parðzÞ ;

(7:6)

8p; w; i; n : Wpn;p ¼ 1; PwsMp;w;i ¼ 1; 8z : stz 2 (7:7)

newn;z yi;w;p;z yi;w;p;parðzÞ ;

8n; z : stz 2

(7:5)

yp;w1;i;z yp;w2;i;z samew1;w2 ¼ 0;

8p; i; z; w1; w2 : w1 6¼ w2

(7:8)

One workplan is selected for each workpiece type in each node z (7.3). The choice of the workplan leads to the definition of the pallet types that must be processed in the system (7.4). As said before, when a new workplan is chosen it is necessary to validate it (7.5) and (7.6), in order to check if the process plan is able to yield products with the required precision. This validation is necessary also when one or more workingstep assignments to the machines are changed (7.7). Finally, also tolerance constraints must be satisfied; since a pallet type can be assigned to more than one machine type thus splitting its related workingsteps, it is necessary to guarantee that critical operations are executed not only on the same pallet, but also on the same machine (7.8). The group of Functionality constraints consists of expressions (7.9), (7.10), (7.11), (7.12) and (7.13) and defines how the process plans are implemented in the manufacturing system: X

xp;i;z Pmp;i xpalp;z ;

8p; z

(7:9)

i

X

xp;i;z xpalp;z L;

8p; z

(7:10)

i

X

yp;w;i;z xp;i;z Pmp;i L;

8p; i; z

(7:11)

yp;w;i;z ¼ xpalp;z Pwsp;w ;

8w; p; z

(7:12)

w

X i

yp;w;i;z PwsMp;w;i ;

8p; w; i; z

(7:13)

The pallet types that are required to complete the selected workplans must be assigned to at least one machine type in each scenario node z (7.9), checking if the pallet can be loaded on the machine (i.e. when Pmp,i = 1). If a pallet type is not required by any workplan, then it must not be assigned to any machine type (7.10).


161

After a pallet type has been assigned to a set of machine types, each workingstep associated with that pallet type must be assigned to only one machine type (7.12). This assignment is possible only if the selected machine type can execute the workingstep (7.13), i.e. when PwsMp,w,i = 1. The group of Capacity constraints consists of expressions (7.14), (7.15), (7.16), (7.17), (7.18), (7.19), (7.20), (7.21), (7.22), (7.23), (7.24), (7.25), (7.26) and (7.27) and deals with the definition of the types and number of resources in each scenario node. Moreover, these constraints calculate the consumption of resource capacity and shortfall volumes: Ni;z ¼ NPi;z þ N0i ;

8i; z : stz ¼ 1

(7:14)

Qz ¼ QPz þ Q0;

8z : stz ¼ 1

(7:15)

Sz ¼ SPz þ S0;

8z : stz ¼ 1

(7:16)

Tp;z ¼ TPp;z þ T0p ;

8p; z : stz ¼ 1

Ni;z ¼ Ni;parðzÞ þ NPi;z NMi;z ; Qz ¼ QparðzÞ þ QPz QMz ; Sz ¼ SparðzÞ þ SPz SMz ; Tp;z ¼ Tp;parðzÞ þ TPp;z TMp;z ;

(7:17)

8i; z : stz 2

(7:18)

8z : stz 2

(7:19)

8z : stz 2

(7:20)

8p; z : stz 2

(7:21)

Nfp Dwep ;z Nwsp;w timep;w;i yp;w;i;z MissWp;w;i;z þ Npartsp p¼1 w¼1 P P Nfp Dwep ;z þ tcpi xp;i;z MissPp;z m 8i; z i Mmi;z Ni;z ; Npartsp p¼1

(7:22)

P P I P Nfp Dwep ;z xp;i;z MissPp;z þ Npartsp p¼1 i¼1 P P Nfp Dwep ;z t Mtz Qz þ xpalp;z MissPp;z ; Npartsp tt p¼1

(7:23)

P P W P

P X p¼1

2tlup

Nfp Dwep ;z xpalp;z MissPp;z l Mlz Sz ; Npartsp

8z

8z

(7:24)

162

W. Terkaj et al.

Nfp Dwep ;z Nwsp;w timep;w;i yp;w;i;z MissWp;w;i;z þ Npartsp i¼1 w¼1 Nf D p wep ;z þ tt þ 2 tlup xpalp;z MissPp;z þ (7:25) Npartsp I P Nfp Dwep ;z þ ðtt þ tcpi Þ xp;i;z MissPp;z Mpp;z Tp;z ; 8p; z Npartsp i¼1 P X I X MISSe;z Ewse;w MissWp;w;i;z ; 8e; w; z (7:26) I P W P

p¼1 i¼1

MISSe;z MissPp;z Npartsp Epe;p ;

8e; p; z

(7:27)

Constraints (7.14), (7.15), (7.16), (7.17), (7.18), (7.19), (7.20) and (7.21) define the number of resources that are available in the system at each scenario node z. The constraints are replicated for each resource type, i.e machine, carrier, load/unload station and pallet. In the root node (7.14), (7.15), (7.16) and (7.17) the total number of resources (Ni,z, Qz, Sz, Tp,z) is equal to the number of devices already available in the system (N0i, Q0, S0, T0p) plus the purchased devices (NPi,z, QPz, SPz, TPp,z) minus the sold devices (NMi,z, QMz, SMz, TMp,z). If system design starts from green field, then there are no devices already available in the system (i.e. N0i, Q0, S0, T0p are all equal to zero). In the stages which follow the first one (7.18), (7.19), (7.20) and (7.21), the parameters representing the number of devices already available in the system are replaced by the variables indicating the number of devices which are available in the parent node. Constraints (7.22), (7.23), (7.24) and (7.25) model how the available capacity of the different resource types can be used to produce the workpieces. In these constraints the actual production volume is calculated as a difference between the demand and the shortfall/outsourcing volume. Machine capacity (7.22) is dedicated both to cutting operations and to the movement of pallets. The first activity is related to the total number of workingsteps and to the time to execute a single workingstep (timep,w,i), while the second activity is related to the number of loaded pallets and to the time required to change the pallet in the working position (tcpi). The available capacity of machine type i in a given scenario node depends on the total number of machines of that type in the system (Ni,z) and on the time capacity of a single machine (Mmi,z) during the planning period of the considered scenario node z. Anyway, this theoretical capacity is reduced by inefficiencies which are due to scraps, maintenance and production planning. Carrier capacity (7.23) is used to transport pallets in the system. The considered missions are the following ones:

from a load/unload station to a machine; from a machine to another machine; from a machine to a load/unload station.


163

With this assumption, each pallet type requires a number of missions that is equal to the number of machines that it has been assigned to plus one; this hypothesis is valid if a pallet does not visit the same machine more than once. The left-hand side of expression (7.23) models the total number of missions, while the right-hand side models the maximum number of missions that the carriers in the system can perform. This maximum number of missions depends on the number of carriers in the system (Qz), on the time capacity (Mtz) of a carrier during the time period of scenario node z and on the mean time required by each mission (tt). The theoretical capacity of the carriers is decreased by inefficiencies which are due to scraps, maintenance and production planning. Moreover, the real carrier availability is reduced because additional missions can be necessary to move the pallets to/from the buffers. These additional missions are taken into account reducing the actual capacity of the carrier by an availability coefficient (), since they cannot be precisely estimated because they depend on the dynamic behavior of the system. Load/unload station capacity (7.24) is dedicated to load and unload workpieces on/from the pallets. The total capacity depends on the number of stations (Sz) and on the time capacity of each station (Mlz) during the planning period of scenario node z. The theoretical capacity is reduced by inefficiencies which are due to scraps, maintenance and production planning. The pallet capacity constraint (7.25) defines how many pallets of each type are necessary to satisfy the demand. The left-hand side of the constraint models the system time required by a pallet to be completely processed. The required time is spent for the following activities: loading of the workpieces, transportation to the various machines, machining of the workpieces, transportation to the load/unload station and finally unloading of the workpieces. The total capacity of each pallet type depends on the number of pallets of that type in the system (Tp,z) and on the time capacity of a single pallet (Mlz) during the planning period of scenario node z. The theoretical capacity is reduced by inefficiencies which are due to scraps and queues in the system . If system capacity is not sufficient to satisfy the demand, then the shortfall/ outsourcing volume of workpiece types can be calculated according to the shortfall of workingsteps (7.26) and pallets (7.27).

7.7 Total Cost Stochastic Model The previous section has presented a multi-stage stochastic programming model to solve the problem of FFMS design. The model aims at identifying the type and number of devices to be purchased in order to face the production problems, while minimizing the system cost consisting of resource investment, shortfall/outsourcing production and process planning decisions. However, in order to develop a detailed analysis of the FFMSs profitability compared to other system architecture, a total cost analysis should be carried out. This

164

W. Terkaj et al.

modeling becomes crucial when system reconfigurations are required to face frequent production changes (Terkaj et al. 2008). Reconfigurability and flexibility are two options that can be mixed in an FFMS on the basis of their costs. For instance, it is possible to acquire more flexibility then the amount strictly required by the present production problem in order to avoid possible future system reconfigurations and ramp-ups. Indeed, the system ramp-up phase represents a critical and less investigated issue. The production system ramp-up is defined in the literature as ‘‘the time interval it takes a newly introduced or just reconfigured production system to reach sustainable, long-term levels of production, in terms of throughput and part quality, considering the impact of equipment and labor on productivity’’ (Koren et al. 1999; Koren 2006). The ability to successfully ramp-up the production when new products are introduced and demand volumes change has become a critical issue for many manufacturing companies, especially for Original Equipment Manufacturers and their suppliers (Matta et al. 2008). Therefore, manufacturers need to manage production ramp-ups both in a time-efficient and in a cost-efficient manner. Many factors impacting on the system ramp-up have been identified and the most influencing ones seem to be related to the learning process (Li and Rajagopalan 1998; Terwiesch and Bohn 2001; Hatch and Macher 2004). Despite the importance of system ramp-up is deeply perceived by companies, it seldom happens that the manufacturing system designer quantitatively considers the phenomenon when configuring new systems or reconfiguring existing ones. It is difficult to precisely evaluate the ramp-up time and cost because they depend on the heterogeneous factors which are involved. However, the analysis of the issues related to the system ramp-up phase supports the idea that neglecting the existence of ramp-ups in the reconfiguration problem can lead to make mistakes in determining the required system capacity and to underestimate the costs related to penalties both for lost production and system inefficiencies (Matta et al. 2008). The main feature of a system ramp-up is the non-steady-state production, due to the system inability to reach its full production potential because of higher frequency of machine/system breakdowns, higher percentage of scrap or reworks and poor understanding of the best way to operate the system in its new configuration. It is possible to consider the case of a production system that has to be designed to cope with a certain demand level and after a period of time it should be reconfigured in order to cope with a new demand level. Figure 7.9 illustrates the production throughput function of the production system introduced in this example. In this case, the present and forecasted production requirements lead the system designer to handle a two-stage decision process. In the first stage the production system has to be designed in order to guarantee a throughput Th1. However, the production system requires a ramp-up period [0; 1) before reaching the objective production rate; this period will be followed by a steady-state period [ 1;Tss1). The ramp-up period is characterized by an insufficient number of processed parts and a growing throughput rate. For the


165

Fig. 7.9 Representation of the production system ramp-up and steady-state phase

sake of simplicity, this phenomenon is represented as a linear ramp in the figure and the steady-state period is characterized by the production of a constant rate of parts. As anticipated, a new level of demand must be satisfied by the system after the end of the first time period. The increased demand forces the decision maker to design a system reconfiguration in which new resources are installed to achieve the throughput level Th2. This means to face a second period composed of a ramp-up and a steady-state phase characterized by the intervals [Tss1; 2) and [ 2; Tss2) respectively. During the ramp-up period, the production system does not reach the target production level. This impacts both on operating and maintenance costs. For instance, penalties related to the lost production as well as intensive maintenance activity related to the higher probability of machine failures and malfunctioning must be considered. Moreover, during the ramp-up phase the purchased resources tend to be used inefficiently thus leading to higher operating costs.

7.7.1 Basic Assumptions The model presented in this section has been developed assuming that the designed manufacturing system must be able to cope with the demand and its forecasted evolution. This means to consider the outsourcing option if the production system does not satisfy the demand. The model does not consider holding costs, i.e. the possibility to keep and maintain a stock of goods in storage. The design model considers the following costs in addition to the investement and outsourcing/shortfall costs (see Sect. 7.6):

Operating costs (related to the production of all the required parts); Maintenance costs.

166

W. Terkaj et al.

Each type of cost has been considered during both the ramp-up and the steady state phases. Other assumptions concern the profile of the system throughput function as it is represented in Fig. 7.9. Firstly, the throughput function linearly increases with time until it reaches the steady state value. Secondly, it is assumed that the duration of the ramp-up phase never exceeds the length of the whole period. Concerning the machine reliability, resource failure and repair rates have already been estimated. The failure rate is related to the resource type. The Total Cost model has been formulated as an extension of the basic FFMS design model presented in Sect. 7.6. Therefore all the parameters (see Sect. 7.6.1), decision variables (see Sect. 7.6.2) and constraints (see Sect. 7.6.3) of the basic model are still valid, except where specified. The additional characteristics of the Total Cost model are defined in the following sub-sections.

7.7.2 Notation and Parameters This section provides the set of new parameters included in the Total Cost model beyond those already defined in Tables 7.2, 7.3, 7.4, 7.5 and 7.6. These additional parameters define the characteristics of the planning horizon and ramp-up phase (Table 7.10), the failure rates (Table 7.11) and the production and maintenance costs (Table 7.12).

Table 7.10 Planning horizon and ramp-up parameters Parameter Definition z Tssz coeffRUz

End of system ramp-up phase in the planning period associated with scenario node z End of system steady state period in the planning period associated with scenario node z Coefficient that reduces the capacity of the new resources during the ramp-up phase in the period associated with scenario node z

Table 7.11 Failure parameters Parameter Definition MTBFRUi MTBFtRU MTBFlRU MTBFi MTBFt MTBFl

Mean time between failures of machines of type i during the rump-up phase Mean time between failures of carriers during the rump-up phase Mean time between failures of load/unload stations during the rump-up phase Mean time between failures of machines of type i during the steady state phase Mean time between failures of carriers during the steady state phase Mean time between failures of load/unload stations during the steady state phase


167

Table 7.12 Production and maintenance cost parameters Parameter Definition pRU p CFprodz CFmantz mi mt ml mp

Production cost during the rump-up phase [cost/pallet] Production cost during the steady state phase [cost/pallet] Fixed production costs in the planning period associated with scenario node z Fixed maintenance costs in the planning period associated with scenario node z Maintenance cost of machines of type i during the ramp-up and steady-state phases [cost/machine] Maintenance cost of carriers during the ramp-up and steady-state phases [cost/ carrier] Maintenance cost of load/unload stations during the ramp-up and steady-state phases [cost/load-unload station] Maintenance cost of pallets of type p [cost/pallet]

7.7.3 Decision Variables The decision variables of the basic FFMS design model have already been introduced in Sect. 7.6.2 (Tables 7.7, 7.8 and 7.9). The additional decision variables modeling the different costs of the system and the number of processed pallets are reported in Table 7.13.

7.7.4 Objective Function and Constraints The Total Cost model is formulated as a multi-stage stochastic programming model. In this sub-section the objective function and the constraints of the model are presented and explained. Constraints (7.2), (7.3), (7.4), (7.5), (7.6), (7.7), (7.8), (7.9), (7.10), (7.11), (7.12), (7.13), (7.14), (7.15), (7.16), (7.17), (7.18), (7.19), (7.20) and (7.21) and (7.26), (7.27) defined in Sect. 7.6.3 for the basic model are still valid in the Total Cost extension. The new objective function (7.28) substitutes (7.1) and it aims at minimizing the expected total cost during the planning horizon. min cost ¼

Z X TCz prz z¼1

ð1 þ rÞstz 1

(7:28)

Table 7.13 Additional decision variables of the Total Cost model Variable Definition TCz 2 R OPz 2 R MANTz 2 R Vp;z 2 R

Total cost in the planning period associated with scenario node z Production cost in the planning period associated with scenario node z Maintenance cost in the planning period associated with scenario node z Production volume of pallets of type p in the planning period associated with scenario node z

168

W. Terkaj et al.

As previously stated, the total cost includes the investment costs (COSTz), the operating costs (OPz) and the maintenance costs (MANTz). The components of the total cost function are defined in constraint (7.29). TCz ¼ COSTz þ OPz þ MANTz ; OPz ¼ CFprodz þ

P X

p Tssz Tssparz Vp;z ;

8z

8z : Vp;z Vp;parz

(7:29)

(7:30)

p¼1

OPz ¼CFprodz þ

þ

P X

P X pRU z Tssparz Þ Vp;z Vp;parz þ 2 p¼1

(7:31)

8z : Vp;z 4Vp;parz

p ðTssz z ÞVp;z ;

p¼1

MANTz ¼ CFmantz þ

P P

mp Tp;z þ

p¼1

I P mi mt ml þ Tssz Tssparz N þ Q þ S þ i;z z z MTBFi MTBFt MTBFl i¼1

I P

þ z Tssparz mi NPi;z z þ i¼1 o 1 1 1 1 þ MTBFt mt QP þ ml SP ; 8i; z; p z z MTBFt MTBFlRU MTBFl RU

1 MTBFRUi

(7:32)

1 MTBFi

The variable COSTz takes into account investment costs, process planning costs and outsourcing/shortfall costs. These costs have already been defined in constraint (7.2) within Sect. 7.6.3. Production costs are defined by constraints (7.30) and (7.31). Constraint (7.30) determines the cost related to process the demanded quantity of pallets when the system does not face a ramp-up. This cost is composed of a constant value and a variable one. The constant value includes fixed costs which are due, for instance, to the rental of buildings. The variable part of the cost depends on the volume of manufactured pallets and it is related, for instance, to the cost of energy required by the resources, labor costs and the cost of raw materials. When production volumes grow from a period to the next one, constraint (7.31) allows to calculate the production costs considering also the ramp-up phase; during this phase the production costs can be higher because of non-optimal settings of the process parameters. Constraints (7.32) models the maintenance costs which consist of four terms: 1. a fixed maintenance cost (CFmantz) allocated by the firm for the ordinary maintenance activities; 2. a cost associated with pallet maintenance;


169

3. a cost required to maintain the total number of devices installed in each system configuration during the period associated with scenario node z; 4. an additional maintenance costs related to the ramp-up period during which possible resource breakdowns or malfunctioning can occur with a higher frequency. Constraint (7.33) defines the total number of processed pallet in the planning period associated with scenario node z, given by the requested volume minus the shortfall volume. Vp;z

Nfp Dwep ;z ¼ xpalp;z MissPp;z ; Npartsp

8p; z

(7:33)

Constraints (7.34), (7.35), (7.36) and (7.37) substitute the capacity constraints (7.22), (7.23), (7.24) and (7.25) of the basic FFMS design model to calculate the capacity of the different resource types: machines (7.34), carriers (7.35), load/unload stations (7.36) and pallets (7.37). The new constraints are similar to the previous ones and most of the terms have the same meaning. The capacity of the new resources which have been purchased to face production changes is reduced during the ramp-up phase by a coefficient coeffRUz. Indeed, the real availability of the resources is limited by the learning processes when new devices are installed in the system. Therefore, a new resource will not be able to immediately achieve its full capacity because of the ramp-up. The coefficient of capacity reduction of new resources (i.e. coeffRUz) has been assumed to be the same for machines, carriers, load/unload stations and pallets. Also, a new resource facing a ramp-up could influence the other resources already present in the system. The level of interaction could be related to the type of resource which has been purchased. Herein, for the sake of simplicity, it is assumed that the ramp-up phenomenon which affects a new resource does not affect the other resources already installed in the system. P X W X Nfp Dwep ;z Nwsp;w timep;w;i yp;w;i;z MissWw;z þ Npartsp p¼1 w¼1 Nfp Dwep ;z þ tcpi xp;i;z MissPp;z Npartsp p¼1 m 8i; z i Mmi;z Ni;z coeffRUz NPi;z ; P X

P X I X Nfp Dwep ;z p¼1 i¼1

Npartsp

(7:34)

X P Nfp Dwep ;z xp;i;z MissPp;z þ xpalp;z MissPp;z Npartsp p¼1 (7:35) t Mtz ðQz coeffRUz QPz Þ ; 8z tt

170

W. Terkaj et al.

P P

2tlup

p¼1

Nfp Dwep ;z xpalp;z MissPp;z Npartsp

(7:36)

l

Mlz ðSz coeffRUz SPz Þ; 8z W P Nfp Dwep ;z Nwsp;w timep;w;i yp;w;i;z MissWw;z þ Npartsp w¼1 Nf D p wep ;z þ tt þ 2 tlup xpalp;z MissPp;z þ Npartsp I P Nfp Dwep ;z þ ðtt þ tcpi Þ xp;i;z MissPp;z Npartsp i¼1 Mpp;z Tp;z coeffRUz TPp;z ; c 8p; z

(7:37)

7.8 Bid Generation Model As introduced in Chap. 1, the problem of system design can be addressed both by machine tool builders and by system users. In this chapter the design activity is carried out by the machine tool builder who identifies a set of alternative system configurations that fit the production requirements with different levels of efficiency and cost-effectiveness. As introduced in Sect. 7.5, the design model presented in this section focuses the attention on the objective function of the machine tool builder. The final goal of the machine tool builder is the maximization of his expected profit and not the minimization of the system cost, even if these two objectives are related. At first, the machine tool builder can identify a set of alternative manufacturing system configurations fitting the production requirements with the minimum economic efforts. Afterwards, starting from the optimal solution he could evaluate how to generate the economic bid aiming at maximizing his expected profit. The works addressing the bid generation problem for a generic seller are typically economics-oriented and study the interaction between seller and buyer defining mathematical utility functions (Talluri 2002; Che and Gale 2000). These approaches are not easy to apply because complex knowledge and elaborations of the decision makers cannot be fully represented by utility functions. To solve this problem Chapman et al. (2000) developed a framework supporting the generation of competitive bids in uncertain environments. The objective of the bid generation model is the maximization of the utility of the machine tool builder, finding the optimal trade-off between profitability and probability of winning the order. The difference between the knowledge and the objectives of the machine tool builder and the system user can lead to manufacturing systems configurations which are suboptimal from the point of


171

view of the system user. This situation can happen in various situations, e.g. when the machine tool builder designs a system with excessive flexibility due to incomplete information received from the system user or when the machine tool builder succeeds in selling an oversized system. Since the point of view of the machine tool builder is adopted, several uncertain issues must be faced while addressing the problem:

the evolution of the part mix and the capacity required by the manufacturing system;

the available capacity in the plant of the machine tool builder is uncertain because the success rate of the present and future bids is unknown;

the financial situation of the client (e.g. budget constraints) and the role of the client in his market;

the technical characteristics and the economic value of the system solutions offered by the competitors of the machine tool builder. To reduce the risk related to the bidding decisions, a tool based on multistage stochastic programming is presented to support the machine tool builder in generating a bid. One of the goals of the Bid Generation model is the quantitative study of how the decisions can impact on the profitability of the firm; the focus is on control parameters such as the markup percentage and the due date of the designed system capacity.

7.8.1 Notation and Parameters The Bid Generation model can be considered as an extension of the basic FFMS design model described in Sect. 7.6 (Tables 7.1, 7.2, 7.3, 7.4, 7.5, 7.6, 7.7, 7.8 and 7.9). Therefore the production requirements of the potential client are still modeled by the scenario tree presented in Fig. 7.1. The additional sets that are necessary for the formulation of the model are shown in Table 7.14. A new set has been introduced to model the different markup levels that a machine tool builder can select. The choice of the machine tool builder is influenced by many factors, e.g. its present financial situation, the saturation of its plant, the importance and the financial situation of the potential client. Since the results of the bid depends on the market context where the machine tool builder plays, another set has been created to model the various market situations that the machine tool builder could face. Table 7.14 Model notation Index Set h j k

Market Situation {1,..,H} Markup Level {1,..,J} Time Stage {1,..,K}

172

W. Terkaj et al.

Table 7.15 Model parameters Parameter Definition mlj fml sprh srh,j ovk budg L

Markup percentage corresponding to the markup level j Mean markup percentage which is applicable when selling resources needed for system reconfigurations Realization probability of market situation h Success rate when markup level j is applied in market situation h Maximum oversizing of the designed system capacity in time stage k Client budget which is available for the initial system configuration High value constant

The parameters of the basic model (Tables 7.2, 7.3, 7.4, 7.5 and 7.6) are integrated with new parameters reported in Table 7.15. These new parameters characterize the markup levels, the market situations, the oversizing of the manufacturing system and the budget of the potential client.

7.8.2 Decision Variables The decision variables of the bid generation model are shown in Table 7.16. These variables are added to the set already defined in Sect. 7.6.2 (Tables 7.7, 7.8 and 7.9) to model the economic decisions.

7.8.3 Objective Function and Constraints The Bid Generation model aims at maximizing the profit of the machine tool builder. However, when dealing with the maximization of the profit it is necessary to introduce the aspect of success rate of a commercial bid; indeed the profit is not certain since the client could prefer the bid prepared by a competitor. Chapman et al. (2000) proposed a simple and plausible objective function maximizing the product of profit and success rate; the success rate linearly depends on the commercial bid and if the bid is increased, then the chance of winning the order decreases. This formulation is applied to cases where the Table 7.16 Decision variables Variable Definition selj 2 {0,1} Bj 2 R FBz 2 R PROFj;z 2 R

Equal to 1 if markup level j has been selected Commercial bid for the initial system configuration when markup level j is selected Commercial bid for the future system reconfiguration in scenario node z Profit in scenario node z when markup level j is selected


173

technical bids proposed by the competitors are very close because the client has defined precise specifications (e.g. civil engineering facilities, health facilities, supply of services, etc.) thus leading to a ‘‘lowest price’’ competition. However, in the case of manufacturing system design, the technical bids of the machine tool builders can be very different. Assuming that the system user can roughly evaluate the economic value of the alternative technological offers (i.e. system configurations) which are able to solve his production problem, the hypothesis can be made that the success rate of the bid depends on the difference between the commercial bid (i.e. the price of the system) and the economic value of the proposed system solution. This difference is equal to the markup and the machine tool builder can impact on his expected profit by choosing among different markup percentage levels (mlj). However, the success rate associated with the markup levels cannot be deterministic because it depends also on external factors (i.e. market competition) which can be modeled by defining different market situations; each market situation has its realization probability. Therefore, the success rate of a bid (srh,j) depends both on the chosen markup level and on the market situation that will happen (herein, it is assumed that the market situation is not related to the characteristics of the scenario nodes evaluated by the machine tool builder). The objective function of the model (7.38) aims at maximizing the expected profit of the machine tool builder. The profit (PROFj,z) associated with each scenario node and markup level is weighted according to the realization probability of market situation h, the success rate of markup level j in market situation h and the realization probability of scenario node z. max

H X h¼1

sprh

J X j¼1

srh;j

Z X

prz PROFj;z

(7:38)

z¼1

All the constraints (7.2), (7.3), (7.4), (7.5), (7.6), (7.7), (7.8), (7.9), (7.10), (7.11), (7.12), (7.13), (7.14), (7.15), (7.16), (7.17), (7.18), (7.19), (7.20), (7.21), (7.22), (7.23), (7.24), (7.25), (7.26) and (7.27) defined for the basic FFMS design model formulation (see Sect. 7.6) are valid also for the bid generation model. Moreover, the constraints (7.39), (7.40), (7.41), (7.42), (7.43), (7.44) and (7.45) must be added to the model. J X

selj 1

(7:39)

j¼1

Bj budg;

8j

(7:40)

Bj 1 þ mlj COSTz ;

8j; z : stz ¼ 1

(7:41)

PROFj;z Bj COSTz ;

8j; z : stz ¼ 1

(7:42)

174

W. Terkaj et al.

FBz ð1 þ fmlÞ COSTz ; PROFj;z FBz COSTz ; PROFj;z selj L;

8z : stz 41

(7:43)

8j; z : stz 41

(7:44)

8j; z

(7:45)

Constraint (7.39) defines that no more than one markup level can be chosen to prepare the commercial bid. Constraint (7.40) imposes that the commercial bid cannot be higher than the budget of the client for any possible markup level. The commercial bid (Bj) for each markup level j cannot exceed the system configuration cost by a quantity equal to the markup (7.41). Constraint (7.42) defines the profit (PROFj,z) obtained by selling the initial system configuration for the first planning period which is associated with the root scenario node. Constraints (7.41) and (7.42) are replaced by constraints (7.43) and (7.44) for the time stages following the first one. Constraint (7.43) defines the commercial bid related to future system reconfigurations, while constraint (7.44) defines the profit coming from these reconfigurations. Constraint (7.45) imposes that if a markup level j is not selected (i.e. selj = 0), then the profit associated with that markup level must be equal to zero. Since the goal of the machine tool builder is the maximization of his profit, there is the risk to design a system configuration that is highly oversized compared to the needs of the system user. Therefore a set of constraints (7.46), (7.47), (7.48) and (7.49) have been introduced to cope with this problem by limiting the system capacity. Nfp Dwep ;z xp;i;z MissPp;z þ Npartsp p¼1 P W P P Nfp Dwep ;z Nwsp;w þð1 þ ovstz Þ timep;w;i yp;w;i;z MissWw;z ; 8i; z Npartsp p¼1 w¼1

(7:46)

P X I X Nfp Dwep ;z t Mtz Qz ð1 þ ovstz Þ xp;i;z MissPp;z þ tt Npartsp p¼1 i¼1 P P Nfp Dwep ;z xpalp;z MissPp;z ; 8z þð1 þ ovstz Þ Npartsp p¼1

(7:47)

m i Mmi;z Ni;z ð1 þ ovstz Þ

l Mlz Sz ð1 þ ovstz Þ

P X p¼1

P P

2tlup

tcpi

Nfp Dwep ;z xpalp;z MissPp;z ; Npartsp

8z (7:48)


175

Nfp Dwep ;z xp;i;z MissPp;z þ Npartsp i¼1 W P Nfp Dwep ;z Nwsp;w (7:49) ð1 þ ovstz Þ timep;w;i yp;w;i;z MissWw;z þ Npartsp w¼1 Nf D p wep ;z þð1 þ ovstz Þ tt þ 2 tlup xpalp;z MissPp;z ; 8p; z Npartsp

Mpp;z Tp;z ð1 þ ovstz Þ

I P

ðtt þ tcpi Þ

For each planning period associated with the different scenario nodes, the system capacity related to machines (7.45), carriers (7.46), load/unload stations (7.47) and pallets (7.48) cannot exceed the required capacity by a quantity equal to the maximum oversizing coefficient. The terms in constraints (7.45), (7.46), (7.47) and (7.48) have already been explained while describing the capacity constraints (7.22), (7.23), (7.24) and (7.25) of the basic FFMS design model (see Sect. 7.6.3).

7.9 Testing The FFMS design model presented in Sect. 7.6 has been tested with the goal of investigating the benefits coming from the application of an FFMS design approach. As anticipated, the existence of a machine database composed of heterogeneous resources (in term of performance, architecture and costs) gives to the machine tool builder more options to customize the system flexibility on the production requirements. The presence of many resource types offers the chance of designing different system configurations to solve the trade-off between flexibility and productivity. Indeed, previous works highlighted that the profitability of the FFMS solution is strongly influenced by the variety of machines composing the resource database (Tolio and Valente 2006, 2007). As stated in Chap. 1, FFMSs are hybrid systems, i.e. they can be composed of general purpose and dedicated machines. A general purpose machine is a traditional machining center that can execute a large set of operations thanks to its precision and flexibility. A dedicated machine is defined as a machine that is able to perform only a subset of all the operations that must be processed. For instance, dedicated machines can be drilling machines or roughing machines; another example of dedicated machine could be an old resource already available in the system, whose degraded performance allow to execute only a subset of operations. Dedicated and general purpose machines differ not only in the set of performable operations but also in the investment cost. General purpose machines are intuitively more expensive than dedicated ones. The cost difference can arise from many aspects. For instance, a machine tool builder can operate on the machine architectures in terms of number of axes and working cube. Other key parameters influencing the machine cost are related to devices such as the

176

W. Terkaj et al.

spindle and the actuators that have an impact on machine performance and in particular on the cutting speed and rapid movement times for the various machining operations. For instance, a machining center dedicated to drilling operations must bear machining forces mainly along one working direction: this consideration enables to optimize the structure and the drives thus reducing the cost. More generally it may be possible to reduce the cost for devices and structural components, making at the same time the machine lighter and faster in rapid traverse movements. A further category is represented by machines whose investment cost reduction is compensated by a worse machine performance. A clear example is represented by old machines, including general purpose ones, which can be dedicated to perform few operations: even if their usage has reduced the precision of the machining process and the quality threshold cannot be satisfied for finishing operations, old machines can frequently be used for roughing operations. When a system configuration or reconfiguration is needed, old machines which are already available in the system can be kept in the new configuration or additional old machines can be purchased in the second-hand market at a lower price than state-of-the-art general purpose machining centers. Therefore, integrating this type of machines can give a competitive advantage to the FFMS solution. The testing phase presented in this section is aimed at:

evaluating the impact of an heterogeneous machine database on the system architecture;

studying which are the types of production contexts where the cost reduction related to dedicated resources can be exploited at a system level, thus making an FFMS a winning solution compared to traditional Flexible Manufacturing System (FMS). An FMS is the system configuration characterized by the highest level of flexibility. The testing activities have been carried out considering a machine database composed of general purpose, drilling and roughing machines. The latter two machine types are considered dedicated resources. The analysis has been applied to a set of production problems characterized by a family of products, each of them with its specific set of operations to be machined. Moreover, a large set of different aggregate demand volumes has been considered keeping fixed the mix ratios. The analysis has ranged from low aggregate demand volumes requiring only one machine, to large size systems characterized by many machines. In this way it is possible to evaluate the range of production requirements where the selection of dedicated resources results more appropriate. The evolutionary concept is not addressed in this section and a static analysis is considered. Therefore the production problems are characterized by a scenario tree consisting of only one node, i.e. the FFMS design model is simplified to a single-stage instance. The impact of dynamic and stochastic aspects of the production problem will be addressed in Chap. 10, where the system performance estimated by the FFMS design model will be compared to simulation


177

results and the value of the stochastic programming approach will be calculated for planning horizons with more than one decision stage.

7.9.1 Test Case The production problems defined to test the FFMS design approach have been built considering a product family consisting of ten mechanical components. Three of these product codes (i.e. codes 240, 280, 900) are described in Sect. 10.1, while the other ones are variants of the products presented in the same section, i.e. products obtained removing some machining features from the original versions. The number of workingsteps for every product ranges from 4 to 19. Analyzing the process plan of the products it is possible to calculate the global cutting time required by the machining operations of every product. The part family can be characterized according to the cutting time that is spent to execute the different operation types. Considering the types of dedicated machines (i.e. drilling and roughing machines), two classification drivers have been defined:

roughing or finishing operations; drilling or non-drilling operations. A dedicated machine can perform only a subset of the operations and in particular a drilling machine can execute only drilling operations (both roughing and finishing), while a roughing machine can process only roughing operations (both drilling and non-drilling). A general purpose machine is a 4-axis machining center that can execute all the required operation. Four test cases have been defined varying the set of products. In the first test case only real products have been considered, while in the other cases also product variants have been introduced. The part mix of the four cases has been defined to characterize the test cases with different percentages of the operation types. This means that the percentage of cutting time dedicated, for instance, to roughing operation is not constant over the test cases. Herein, the percentage of operation types has been changed to study how it can impact on the selection of the machine types. The operation percentages of the four test cases are reported in Table 7.17. Table 7.17 Test cases and operation type percentages Roughing Finishing Drilling Test operation time operation time operation time case percentage percentage percentage

Non-drilling operation time percentage

1 2 3 4

50% 70% 50% 70%

60% 60% 40% 40%

40% 40% 60% 60%

50% 30% 50% 30%

178

W. Terkaj et al.

The aggregate demand of the four basic test cases has been defined aiming at having an equal total cutting time for the different cases, thus allowing a better comparison of the test results. The aggregate demand has a deep impact on the optimal system solution and on the possibility of customizing the flexibility of the system. Therefore, starting from the initial aggregate demand that guarantees an equal total cutting time for the four test cases, 250 different levels of aggregate demand volume have been defined. The demand volume of each level is 10% greater than the demand of the previous level. This means that 1000 experimental conditions have been tested. The first level of aggregate demand has been set to a value so that the designed system requires only one machine. In general process plans can be optimized according to the machine type where the machining operations are executed. However, the simplifying hypothesis is made that the cutting time of the operations does not depend on the machine type. Herein the machine architecture and performance have an impact only on the rapid time and on the pallet change time. A general purpose is more expensive than a dedicated machine in term of investment cost because it is endowed with higher flexibility. For the sake of simplicity, all the dedicated resources (i.e. drilling and roughing machines) are assumed to have the same investment cost. Data related to resource investment costs are usually difficult to be collected and often cannot be compared. For this reason, the cost of dedicated machines has been set assuming a percentage reduction of the general purpose machine cost. Three levels of cost reduction have been considered: 10%, 30% and 50%. A reduction lower than 10% could hardly justify the investment to build a dedicated machine instead of a general purpose one, while a reduction greater than 50% can be reached only in particular situations. For each of the 1000 experimental conditions, the system design model has been launched four times: once to design an FMS (i.e. a system with only general purpose machines) and three times to design an FFMS characterized by the different cost reduction levels for the dedicated machines. The three FFMS configurations have been named FFMS-10, FFMS30 and FFMS-50% when the cost reduction of dedicated machines is equal to 10, 30 and 50%, respectively.

7.9.2 Profitability of FFMS Solutions The FFMS design model presented in Sect. 7.6 has been implemented in ILOG OPL language and ILOG CPLEX 10.1 in a Cþþ environment. As anticipated in the previous sub-section, the experimentation has been carried out considering at first a machine database composed exclusively of general purpose machines and then including in the database also dedicated resources. The comparison of FMS and FFMS investment costs highlights that focusing system flexibility is profitable for all the considered test cases. This means that the introduction of dedicated resources within the machine database


179

Fig. 7.10 Percentage of dedicated machines for the FFMS-50% solution in Test Case n.1

represents an option to provide a winning system solution. In particular, the option of focusing the flexibility can be better exploited when the aggregate demand increases. Indeed, mid-high levels of demand require to select more resources thus enabling the customization option. This phenomenon can be noticed in Fig. 7.10 where the percentage of dedicated machines is reported for the FFMS-50% solution of Test Case n.1. The graph clearly shows that for low demand levels it is more difficult to insert dedicated machines in the system. It is also clear from the graph that as soon as the demand increases dedicated machines become a profitable option. The mean percentage of dedicated machines calculated over the 250 aggregate demand levels is reported in Table 7.18 for the three types of FFMS solutions. The results show that both the cost of the dedicated machines and the characteristics of the production problem have an impact on how the system flexibility can be focused. The test cases require different degree of flexibility and, in particular, Test Case n.1 allows to design the production systems characterized by the lowest level of flexibility. After an analysis of the FFMS architecture solutions, also an economic analysis can be carried out considering the performance indicator Dcost% (7.50) that is defined as the percentage difference between the FMS cost and the FFMS cost. cost% ¼

ðFMScostÞ ðFFMScostÞ 100 ðFMScostÞ

(7:50)

Table 7.18 Mean percentage of dedicated machines in FFMS solutions System configuration Test Case n.1 Test Case n.2 Test Case n.3

Test Case n.4

FFMS-10% FFMS-30% FFMS-50%

39.83 51.10 52.96

64.76 68.80 69.14

55.29 62.34 63.48

49.83 55.28 55.51

180

W. Terkaj et al.

Fig. 7.11 Profitability of FFMS solutions in Test Case n.1 – Dcost% indicator

Through this parameter it is possible to evaluate how the cost of dedicated machines and the ratio of operation types influence the FFMS profitability. Figures 7.11, 7.12, 7.13 and 7.14 show the profitability of the FFMS solutions as a function of the aggregate demand. Each figure refers to a different test case and in each figure the three FFMS solutions are reported. Table 7.19 reports the mean values of Dcost% for each test case and for each type of FFMS solution (i.e. FFMS-10, FFMS-30 and FFMS-50%) according to the cost reduction of the dedicated machine. The results show that by introducing in the database of selectable machines some less expensive dedicated machines it is possible to significantly affect the



181



cost of the whole system. For instance, considering Test Case n.1, if the machine database includes selectable resources whose cost is 30% less then the cost of general purpose machine, then the designed FFMS system allows to reduce the Table 7.19 Mean profitability of FFMS solutions – mean cost% System configuration Test Case n.1 Test Case n.2 Test Case n.3

Test Case n.4

FFMS-10% FFMS-30% FFMS-50%

3.08 11.69 21.21

5.27 17.55 30.10

4.51 15.57 27.18

3.93 13.74 23.85

182

W. Terkaj et al.

Table 7.20 System classes System class Number of machines in the FMS solution

Demand level range

Small size Medium size Large size

4–27 28–52 53–89

From 2 to 3 From 4 to 5 From 6 to 8

investment by 17.55% on average compared to a traditional parallel machine FMS. However, the aggregation of all the 250 demand levels belonging to a test case can be misleading, because small size systems would be considered together with large size systems. Therefore, the demand levels of each test case have been grouped according to the dimension of the FMS solution that is required to address the production problem. Three classes of manufacturing system have been defined as reported in Table 7.20. Very small systems with just one machine have not been considered because they are not interesting for the application of the FFMS approach: indeed, no dedicated resource can be acquired. Also very large systems with more than 8 machines have been discarded because this kind of manufacturing systems is rather rare to be found in practice. Table 7.21 enriches the results presented in Table 7.19 by reporting the mean FFMS profitability for each system class. In general, both the system size and the cost of the dedicated machines have an impact on the profitability of the FFMS solutions: the larger is the system size and the cost reduction of dedicated machines, the higher is the profitability. However, even for small size systems the FFMS solutions have an interesting profitability; for instance, the FFMS-30% solution for small systems in the Test Case n.2 gives a mean profitability of 14.96%. This is relevant especially considering that system investment costs are typically in the order of millions of Euros. Moreover, Tolio and Valente (2006) have already shown that the costeffectiveness of the FFMS solution improves if the machine database is composed of different machine types (in terms of operations that can be performed). Table 7.21 Mean profitability of FFMS solutions for each system class – mean cost% System Test Case Test Case Test Case Test Case configuration System class n.1 n.2 n.3 n.4 FFMS-10% FFMS-10% FFMS-10% FFMS-30% FFMS-30% FFMS-30% FFMS-50% FFMS-50% FFMS-50%

Small size Medium size Large size Small size Medium size Large size Small size Medium size Large size

5.03 5.83 5.27 15.22 17.83 17.78 25.41 29.91 30.57

4.94 4.57 5.05 14.96 14.36 16.48 24.99 24.63 27.98

4.38 3.53 3.99 13.24 12.96 13.44 22.11 22.92 23.38

3.25 3.41 3.30 9.92 11.83 11.98 16.58 21.30 21.47


183

In this sense, the development of a heterogeneous machine database underpins the profitability of the solution. As previously stated, the test cases differ in the technological characteristics of the products composing the part family. The results show that also the type of operations to be machined in the system have an impact on the profitability of the FFMS solutions: the higher is the fraction of roughing and drilling operation, the higher is the profitability of FFMS solutions. Test Case n.1 has the largest amount of roughing and drilling operations and it is the test case where the mean FFMS profitability is the highest for all the three FFMS solutions and for all the system sizes (Table 7.21). Indeed, in this test case it is easier to focus the production flexibility by inserting dedicated machines in the system. The FFMS profitability is low in Test Case n.4 which is characterized by the lowest percentage of cutting time spent for drilling and roughing operations; Test Case n.4 represents a production problem requiring more flexibility than the other cases: therefore, focusing the flexibility becomes quite difficult. Observing Figs. 7.11, 7.12, 7.13 and 7.14, it can be seen that the FFMS profitability grows when the aggregate demand increases, until it reaches an asymptotic value. This asymptotic value depends on the production problem characteristics (i.e. ratio of operation types) and on the cost of the dedicated resources, as it has already been shown for the mean profitability (Tables 7.19 and 7.21). However, the FFMS profitability does not monotonically increase and even with high demand levels there are fluctuations around the asymptotic value. This fluctuations are mainly caused by the discrete nature of the resources. High peaks represent situations where the difference between the FFMS and the FMS solutions is enhanced, while low peaks coincide with non favorable cases where the FFMS solution is closer to the FMS one. The frequency and the magnitude of the fluctuations are influenced by the type of production problem and also by the cost of the dedicated resources. A low fraction of drilling and roughing operations (e.g. Test Case n.4) leads to more frequent fluctuations because the dedicated resources cannot be well saturated. Indeed, the amount of drilling and roughing cutting time depends on the aggregate demand and in some demand levels it is difficult to keep stable the proportion of dedicated resources because of scarce saturation. The cost of the dedicated machines impacts on the magnitude of the fluctuations. A high cost difference between general purpose and dedicated machines leads to larger fluctuations because the reduction of the fraction of dedicated machines has a deep impact on the system cost. The transient reduction of FFMS profitability when the aggregate demand grows can be explained by analyzing two main performance indicators: 1. Saturation of the machines (general purpose or dedicated) in the FFMS solution; 2. Saturation of the carrier in the FFMS solution. When the capacity of the general purpose machines has been saturated, while the dedicated machines are still unsaturated, it is necessary to acquire a new general

184

W. Terkaj et al.

purpose machine as soon as the demand grows, because the number of general purpose machines is not enough to process all the finishing and/or non-drilling operations. This leads to acquire a new general purpose machine thus reducing the fraction of dedicated resources in the system and also the FFMS profitability. The carrier gets saturated earlier in the FFMS solutions than in FMS solutions. Indeed, some pallets have to visit both general purpose and dedicated machines in an FFMS. As a consequence, the number of carrier missions increases. When the carrier is saturated there are two viable reactions:

Acquisition of an additional carrier; Reduction of the number of operations assigned to the dedicated machines in order to decrease the number of carrier missions. This action could require to acquire more general purpose machines. The choice of the best reaction depends on the cost of the carrier and on the economic difference between a general purpose and a dedicated machine. In both cases the FFMS investment cost gets closer to the FMS investment cost. The evolution of FFMS profitability can be better understood paying attention to the example represented by Test Case n.1. The analysis of the most significant phenomena taking place within the initial 80 demand levels is reported in Table 7.22. These phenomena explain the fluctuations of the FFMS profitability. The number of general purpose and dedicated machines in the FFMS solutions of Test Case n.1 can be further analyzed looking at Figs. 7.15 and 7.16.

Table 7.22 Phenomena influencing the FFMS profitability in Test Case n.1 Demand Explanation of significant phenomena Level 1 4 16 28 40

41

52

The FMS and the FFMS solutions consist only of one general purpose machine and one carrier. One general purpose machine is not sufficient. The first dedicated machine is added to the FFMS solutions and the FFMS profitability grows. The second dedicated machine is added to the FFMS solutions. The FFMS profitability grows. The third dedicated machine is added to the FFMS solutions. The FFMS profitability grows. The unique general purpose machine is saturated in the FFMS solutions. One dedicated machine is substituted by a general purpose one, thus reducing the cost difference between the FFMS and FMS solutions. Also the dedicated resources are saturated in the FFMS solutions. The third dedicated machine is added again to the FFMS solutions and the FFMS profitability grows. The carrier is saturated in the FFMS solutions. In the FFMS-50% and FFMS-30% solutions this problem is faced by acquiring a second carrier, while in the FFMS-10% by substituting a dedicated machine with a general purpose one in order to reduce the number of carrier missions. The FFMS profitability decreases.


185

Table 7.22 (continued) Demand Explanation of significant phenomena Level 53

54

63

65 77

Machines are saturated in the FMS and the FFMS solutions and it is necessary to acquire an additional machine. In FFMS-50% and FFMS30% solutions a dedicated machine is acquired, while in FFMS-10% two dedicated machines are purchased and a general purpose is dismissed. In these new configurations the machines are less saturated and it is possible to better manage the assignment of the operations to the different machine types in order to reduce the number of pallets that need to visit more than one machine. In this way the number of carrier missions is reduced and it results that one carrier is sufficient in all the FFMS solutions. Compared to the previous case (demand level 52), the higher fraction of dedicated machines and the dismission of a carrier lead to increase the FFMS profitability. Again the carrier is saturated in the FFMS solutions. In the FFMS-50% and FFMS-30% solutions this problem is faced by acquiring a second carrier, while in the FFMS-10% by substituting a dedicated machine with a general purpose one in order to reduce the number of carrier missions. The FFMS profitability decreases. The carrier is saturated in the FFMS-10% and the second carrier is acquired. In this way the number of dedicated and general purpose machines becomes equal in all the FFMS solutions, since the effect of the carrier saturation is removed. The fifth dedicated machine is added to the FFMS solutions. The FFMS profitability grows. The sixth dedicated machine is added to the FFMS solutions. The FFMS profitability grows.

Fig. 7.15 Machine types in Test Case n.1 for FFMS-30% solution

186

W. Terkaj et al.

Fig. 7.16 Machine types in Test Case n.1 for FFMS-10% solution

The number of machines in the FFMS-30% solution for Test Case n.1 corresponds exactly to the number of machines in the FFMS-50%. Figure 7.15 reports the solution in the case of FFMS-30%. At low demand volumes there is only one machine in the system; this machine must be a general purpose because it is necessary to process all the operation types. At demand level n.80 there are 6 dedicated machines and 2 general purpose: the high number of dedicated machines is related to the low level of flexibility required by Test Case n.1. By comparing Figs. 7.15 and 7.16, it can be seen that until demand level n.51, the system solutions in the FFMS-10% and FFMS-30% for Test Case n.1 are identical. In the range between demand levels n.52 and n.62 there is a significant difference. This difference is due to the carrier effect on the system. In the FFMS-30% case the cost difference between a general purpose and a dedicated machine is greater than the cost of a carrier; on the other hand, in the FFMS-10% case the cost difference between a general purpose and a dedicated machine is lower than the cost of a carrier. Therefore, in the FFMS-30% solutions it is effective to acquire many dedicated machines even if it is necessary to buy an additional carrier to cope with the increased number of carrier missions; the acquisition of the second carrier is made at demand level n.52 (see Table 7.20). Instead, in the FFMS-10% case the acquisition of the second carrier is postponed as much as possible; in order to reduce the number of carrier missions, after demand level n.52 the flexibility of the system is less focused because general purpose machines are acquired instead of dedicated ones. Anyway, after demand level n.63 it is strictly necessary to buy the second carrier also for the FFMS-10% solution and it is possible to focus again the system flexibility. The carrier saturations for FMS, FFMS-10% and FFMS-30% solutions in Test Case n.1 are reported in Fig. 7.17. When the number of carriers in the


187

Fig. 7.17 Carrier saturation in Test Case n.1

system solutions is equal (i.e. until demand level n. 51), then carrier saturation in the FFMS is higher than in the FMS because some pallets need to visit more than one machining center, thus leading to a larger number of carrier missions and a higher saturation. The FFMS-10% solution avoids to acquire the second carrier until demand level n.63; therefore the carrier saturation remains close to 100% between demand levels n.52 and n.62. Finally, it can be noted that in the FMS solution the second carrier is purchased at the demand level n.69. The analysis carried out for the initial demand levels of Test Case n.1 can be extended also to higher demand levels. Moreover, in the other three test cases the phenomena taking place are similar to those described in Table 7.22.

7.10 Conclusions This chapter has presented an FFMS design approach which can be fully integrated in the FFMS design architecture presented in Chap. 1. The key points of the approach consist of the adopted technique (i.e. stochastic programming) and in the structured approach to the problem that requires a detailed formalization of the production problem (i.e. demand and technological information). The testing results show that an FFMS solution can yield a relevant economic advantage at a system level if a machine tool builder succeeds in developing dedicated machines requiring a lower investment cost. Dedicated resources with a much lower investment cost have a two-fold impact:

A greater amount of cost reduction can be transferred at a system level; FFMS solutions are more robust than FMS solutions towards changes in the aggregate demand.

188

W. Terkaj et al.

Indeed, focusing the system flexibility allows the machine tool builders to provide solutions which are cost-effective and sufficiently robust if compared to traditional FMSs. In this sense, even if the industrial impact of FFMS is still weak, the obtained results suggest the opportunity to investigate new technological solutions and new system architectures that can lead to competitive advantages, thus increasing the chance to win the orders.

7.11 Open Research Issues The research about Focused Flexibility Manufacturing Systems has still to address some important topics:

modeling of short- and mid-term variability of the production problems during the system design process;

the variability related to the manufacturing system (i.e. resource availability) should be further investigated by the future manufacturing system design models;

the problem of manufacturing system design is characterized by important

intangible criteria that should be considered together with quantitative aspects in a multi-criteria decision approach; the modeling of the ramp-up phenomenon can be further enhanced including, for instance, the learning process which influences the resource efficiency and availability as well as the impact of the ramp-up of each resource on the whole system efficiency; the development of a support tool for machine tool builders requires to model also the capacity of the plant of the machine tool builder system (i.e. the plant where manufacturing systems are produced), that consists of different divisions (e.g. assembling, wiring, testing, etc.). The resources composing the designed manufacturing system can be built using internal capacity or more expensive extra capacity (e.g. outsourcing, overtime work). This analysis could influence the type of machines that the machine tool builder sells: for instance, it could be more profitable to sell the machine types whose requirements best fit the available capacity of the plant of the machine tool builder; the machine tool builder should also have the possibility to operate on some control parameters such as the due date of the designed system and the preferences for the type of resources to be installed in the system configuration; finally, the opportunity to extend the Focused Flexibility approach to different production processes (e.g. assembly) and production contexts (e.g. aeronautic field) should be evaluated.

Acknowledgments The research has been partially funded by the MUR (Italian Ministry for University and Research) under the PRIN project ‘‘Methodologies and tools for the configuration of production systems with focused flexibility’’, contract code: 2005097985.


189

References Amico M, Asl FM, Pasek Z, Perrone G (2006) Real Options: an Application to RMS Investment Evaluation. In: Dashchenko AI (ed) Reconfigurable manufacturing systems and transformable factories. Springer, pp 675–693 Asl FM, Ulsoy AG (2002) Capacity Management in Reconfigurable Manufacturing Systems with stochastic market demand. Proc of the 2002 ASME Int Mech Eng Congr and Expo, New Orleans, Louisiana, November 17–22, 2002 Asl FM, Ulsoy AG (2003) Stochastic Optimal Capacity Management in Reconfigurable Manufacturing Systems. Ann CIRP, 52(1):371–374 Birge JR, Louveaux FV (1997) Introduction to Stochastic Programming. Springer, London Buyurgana N, Saygin C, Engin Kilic SES (2004) Tool allocation in flexible manufacturing systems with tool alternatives. Robotics and Computer-Integrated Manufacturing 20/4: 341–349 Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceedings of the 4th International Conference on Digital Enterprise Technology, Bath, UK, 19–21 September, pp 627–636 Chapman CB, Ward SC, Bennell JA (2000) Incorporating uncertainty in competitive bidding. Int J Project Manag 18:337–347 Che YK, Gale I (2000) The Optimal Mechanism for Selling to a Budget-Constrained Buyer. J Econ Theory 92:198–233 Colosimo BM, Poggi A, Tolio T (2002) The tooling system configuration in a new manufacturing system architecture. Int J Prod Res 40(15):3779–3790 Contini P, Tolio T (2004) Computer aided setup planning for machining centers configuration. Int J Prod Res, 42(17):3473–3491 Deif AM, ElMaraghy W (2006) Effect of reconfiguration costs on planning for capacity scalability in reconfigurable manufacturing systems. Int J Flex Manuf Systems 18:225–238 Ganzi E, Tolio T (2003) Configuration and Re-configuration of Manufacturing Systems with Focused Flexibility. 6th Convegno A.I.Te.M., Gaeta, Sept 2003, pp 1–10. Grieco A, Semeraro Q, Tolio T, Toma T (1995) Simulation of tool and part flow in FMSs. Int J Prod Res 33(3):643–658 Hatch NW, Macher JT (2004) Knowledge Management in Developing New Technologies: Mitigating the Trade-off between Time-to-Market and Manufacturing Performance. Proc 2nd World Conf on Prod and Oper Manag, Cancun, Mexico, 30 April – 3May Koren Y (2006) General RMS Characteristics. Comparison with Dedicated and Flexible Systems. In: Dashchenko AI (2006) Reconfigurable Manufacturing Systems and Transformable Factories, Berlin/Heidelberg, Springer Verlag, pp 27–46 Koren Y, Heisel U, Jovane F, Moriwaki T, Pritschow G, Ulsoy G, Van Brussel H (1999) Reconfigurable Manufacturing Systems. Ann CIRP 48(2):1–14 Laporte G, Louveaux FV (1993) The integer L-shaped methods for stochastic integer programs with complete recourse. Oper Res Letters, 13(3):132–42 Li G, Rajagopalan S (1998) Process Improvement, Quality and Learning Effects. Manag Sci 44:1517–1532 Manassero G, Semeraro Q, Tolio T (2004) A new method to cope with decision makers’ uncertainty in the equipment selection process. Ann CIRP 53(1):389–392 Matta A, Tolio T, Karaesmen F, Dallery F (2001) An integrated approach for the configuration of automated manufacturing systems. Robotics Comput Integr Manuf 17:19–26 Matta A., Tontini F, Tolio T (2004) Tool Management in Flexible Manufacturing Systems with Network Part Program. Int J Prod Res 42:3707–3730 Matta A, Semeraro Q Tolio T (2005) Configuration of AMSs – Stochastic models for performance evaluation of Automated Manufacturing Systems. In: Matta A, Semeraro Q (ed) Design advanced manufacturing systems – Models for capacity planning in advanced manufacturing systems. Springer

190

W. Terkaj et al.

Matta A, Tomasella M, Valente A. (2008) Impact of ramp-up on the optimal capacity-related reconfiguration policy. Int J Flex Manuf Syst, 19(3):173–194 Park T, Lee H, Lee H (2001) FMS design model with multiple objectives using compromised programming. Int J Prod Res 39:3513–3528 Sen S, Higle JL (2005) The C3 Theorem and a D2 Algorithm for Large Scale Stochastic Mixed-Integer Programming: Set Convexification. Math Program 104:1–20 Sen S, Sherali HD (2006) Decomposition with Branch-and-Cut Approaches for Two-Stage Stochastic Mixed-Integer Programming. Math Program 106:203–223 Shin H, Park J, Lee C, Park J (1997) A Decision Support Model for the Initial Design of FMS. Comput Ind Eng 33:549–552 Talluri S (2002) A buyer-seller game model for selection and negotiation of purchasing bids. Eur J Oper Res 143:171–180 Terkaj W, Tolio T (2007) An approach to production system design considering the utility of the machine tool builder. 40th CIRP Int Seminar on Manuf Syst, Liverpool, UK, 30 May1 June Terkaj W, Tolio T, Valente A (2008) Focused Flexibility in Production Systems. In: ElMaraghy H (ed) Changeable and Reconfigurable Manufacturing Systems. Springer Terwiesch C, Bohn RE (2001) Learning and process improvement during production rampup. Int J Prod Econ 70:1–19 Tolio T (2006) Co-Evolution of Product Families and Manufacturing Systems. SPECIES Working Group. 56th Cirp General Assembly, Kobe, Japan, Aug2006 Tolio T, Valente A (2006) An Approach to Design the Flexibility Degree in Flexible Manufacturing System. Proc of Flex Autom & Intell Manuf Conf, Limerick, Ireland, June 25–27 2006, pp 1229–1236 Tolio T, Valente A (2007) A Stochastic Approach to Design the Flexibility Degree in Manufacturing Systems with Focused Flexibility. Proc of 4th Int Conf on Digit Enterprise Technol, Bath, UK, 19–21 Sept, pp 380–390 Tolio T, Valente A (2008) A Stochastic Programming Approach to Design the Production System Flexibility Considering the Evolution of the Part Families. To appear in Int J Manuf Technol Manag – Special Issue on Reconfigurable Manufacturing Systems Tolio T, Terkaj W, Valente A (2007) Focused Flexibility and Production System Evolution. . Proc of 2nd Int Conf on Chang, Agile, Reconfigurable and Virtual Prod, Toronto, Canada, 23–24 July 2007, pp 17–41 Wiendahl H-P, ElMaraghy HA, Nyhuis P, Za¨h MF, Wiendahl H-H, Duffie N, Brieke M (2007) Changeable Manufacturing – Classification, Design and Operation. Ann CIRP 56(2):783–809

Chapter 8

System Life-Cycle Planning Marco Cantamessa, Carlo Capello and Giuseppe Cordella

Abstract This chapter introduces a computational model to support the system user along the decision making process regarding the type and timing of system configurations to be acquired and the appropriate flexibility degree. Based on the empirical evidence described in Chap. 2, Focused Flexibility Manufacturing Systems (FFMS) seem to be a viable alternative to solve the classical dichotomy between rigid and fully flexible systems. This focused flexibility concept, as introduced in Chap. 3, can be a valuable solution for manufacturing firms to satisfy the market needs. Previous chapters tackled the system flexibility design process from the machine tool builder standpoint. Once the potential system configurations have been defined and the capital outlays required for acquiring and/or transitioning among them have been quantified, the machine tool builder makes an offer to the system user. The latter needs to select the most profitable solution by evaluating the performance generated by each configuration under different demand profiles from a financial point of view. This decision is supported by two optimization models, one static – i.e. not affected by the time dimension – and one dynamic, wrapped up in a valuation model which simulates a profit function on different variable values over a multi-period time horizon, matching the user’s expected demand levels with his manufacturing strategies. Keywords System life-cycle planning Mixed-integer linear programming Focused flexibility Real options

8.1 Introduction Manufacturing small and medium-sized enterprises (SMEs) are to maintain and upgrade their manufacturing plants in order to constantly align their offer to market requests and improve production performance. This is a C. Capello (*) Dipartimento di Sistemi di Produzione ed Economia dell’Azienda, Politecnico di Torino, Torino, Italy e-mail: [email protected]


191

192

M. Cantamessa et al.

tough problem, as they have to find and implement the optimal mix between manufacturing flexibility and capacity and adjust it over a long-term horizon (Tolio and Valente 2006). If they do not do so, they risk not being able to satisfy their customers and reach the internal performance goals. An investment decision in a manufacturing system, rather than in a single machining center or cell, usually derives from a negotiation between the manufacturing company (i.e. the system user) and one or more suppliers (i.e. machine tool builders). The process is complex as it involves different objectives, boundaries and perspectives (Tolio et al. 2007). The system user usually looks for something that enables it to face the current and expected uncertainty on the market and limit the investment as much as possible. The machine tool builder aims to satisfy the user requests and, on the other hand, maximize its profit by keeping costs down and revenues up, consistently with its capacity constraints. Due to these asymmetries, the result of the negotiation can easily be a sub-optimal solution. The negotiation process includes some basic steps that can be repeated a number of times. These steps are sequential and iterative, that is they can be looped several times before converging to a final result. The system user at first develops a business strategy and structures the manufacturing plant so as to align the composition and timing of part mix with market demand. The user generally works with demand projections and searches the manufacturing configuration that matches these expectations within a given budget. The machine tool builder works on this information, and adds some of its own internal constraints such as capacity and time availability. It designs some manufacturing alternatives characterized by different flexibility degrees that can be used and adapted to the expected production paths laid out from the client over a multi-year horizon. The spectrum of manufacturing solutions can be rather broad: the machine tool builder may propose highly flexible machining solutions, close to the FMS concept, that allow the client to process a wide variety of components and materials, albeit with a high initial investment and a complex execution. On the other hand, it can design a system with rigid machines, which are generally less costly and complex to handle than an FMS – assuming production capacity as constant – but limited to a narrower range of part types. In addition, according to the trends highlighted by empirical evidence (see Chap. 3), the system designer can propose something closer to the FFMS concept, i.e. a solution whose flexibility is specifically tailored to the client’s needs, and that gives the opportunity for further upgrades and reconfigurations. In the end, the designer wraps all the designed solutions up in a commercial bid, reporting investment and switching costs for all potential solutions and related reconfigurations, plus additional boundaries and performance specifications. Once the system user receives the bid, it faces the problem of assessing all possible configurations and reconfigurations. The two ‘‘extreme’’ choices of the FMS and the rigid manufacturing system entail the risks of respectively not being able to pay the investment back in an acceptable time span, or not being

8 System Life-Cycle Planning

193

able to follow shifts in demand. Of course, other possibilities are available, such as planning to follow changes in demand with either outsourcing or reconfiguration of manufacturing resources. The following section reviews some literature about the system life-cycle planning problem and describes inputs and outputs for the valuation model. Section 8.3 introduces in-depth the valuation model structure and Sect. 8.4 describes the set of indexes that will be used in the model. Sections 8.5 and 8.6 analyze the two components of the model, namely the static and the sequential models. In the end, Sect. 8.7 shows an application model example and Sect. 8.8 concludes the chapter.

8.2 Introduction to Life-Cycle Planning Empirical evidence discussed in Chap. 2 shows that system users usually have a hard time in assessing the proposed manufacturing solutions and selecting the one that matches current and expected market needs. Planning and evaluating flexible capacity is hard, as many conflicting objectives and constraints are to be considered: maximizing profit; minimizing risk; lowering initial investments; increasing capacity and flexibility according to the market needs; reducing upstream dependency on outsourcers and sub-contractors; decreasing production penalties; maximizing the recovery value for each legacy resource. In addition, the interaction between system user and system designer makes the problem more complex given that new objectives and constraints are to be integrated with the counterpart’s ones. Sometimes manufacturing SMEs do not even realize such complexities and tend to make very rough assessments and use their experience to plan and decide on their manufacturing capacity. They do not make a thorough validation for consistency with their business strategy, company skills, competencies, and market evolutions. They do perceive the problem though, which leads to the need for methods and tools which may help in rationalizing the relevant information and plan the investment for a new manufacturing system over its life-cycle. As a large body of literature proves, the problems of planning and evaluating investments in manufacturing flexibility over the long-term period have been deeply investigated. This is a tough as well as necessary activity to profitably operate in rapidly changing and risking environments. Firms must design their manufacturing plant flexibility and then make operating decisions to satisfy their profit objective, subject to multiple boundaries. Cheng et al. (2003) interpreted this problem in a chemical company as ‘‘design/investment planning under uncertainty’’ and investigated it from the whole company perspective in order to consider all the potential complexities. They tried to capture and solve the difficulty for the executive management in satisfying conflicting goals as maximizing expected profit, minimizing risk, sustaining long-term viability and competitiveness. They considered different kinds of uncertainties

194


including market conditions (part type, demand, price, etc.) and technology improvements (timing and magnitude of future technology breakthroughs such as improved flexibility degrees) and incorporated upper-level design and lower level production decisions at each period of the decision process. Technically, they modeled this problem as a Markov decision process with recourse that considers decision making throughout the process life-cycle. This leads to a multi-objective Markov decision problem, searching for Pareto optimal design strategies that prescribe design decisions for each state the environment and process could occupy. The final outcome is an intensive computational algorithm that is hard to be applied to a realistic problem due to a matter of dimensionality and the need of approximations that may heavily distort the results. Perrone et al. (2002) studied this problem from the manufacturing company perspective, and developed a decision support model for investment decisions in flexible systems. They identified three sequential decision phases: strategic design, production system configuration and detailed design. They then developed a theoretical framework in order to assess different system configurations on the benefits due to economies of scope associated with flexible manufacturing systems versus dedicated systems, and support longterm capacity decisions. Matta et al. (2001) proposed an integrated approach for supporting firms in their decisions in configuring and dimensioning automated production systems. The objective of the method is to identify a set of alternative production systems among which the manager of the firm can select the one he considers the best. For this purpose, the method works with a set of performance indicators to enable the decision-maker to calculate the expected net present value of the investment in several alternative configurations. This method would therefore be useful to choose the flexible system even though it would need further modifications to include the reconfiguration concept proper for the FFMS case. Choi and Kim (1998) developed a comprehensive approach for measuring flexibility in manufacturing systems in terms of total processing time. It is useful to have a major insight into how to appreciate manufacturing flexibility and which the related lower inefficient time benefits are, however this approach does not include any decision variables, and therefore does not support capacity planning decisions. Elkins et al. (2004) developed two simple decision models with the purpose of providing insight in analyzing business case for investment in agile manufacturing systems (AMSs), compared to FMSs and rigid systems. The outcome is a couple of models that can support the decision-making process and are simpler than the ones developed by the above contributions. However, one of them is based on a set of qualitative comparison factors that are useful to develop a profile for each system solutions but does include neither decision variables nor time axis. The other one formalizes the problem of modeling varying demand and part mix by using decision trees: however event probabilities are subjectively set and branches are too much simplistic to be used for modeling complex problem such as system life-cycle planning over time.


195

Some of these authors deal with the problem of choosing among rigid and flexible systems, but either do not take the possible evolution of the system into account, or do so with models that are highly complex from the computational point of view and as far as practical usability is concerned. When dealing with the evolution of the manufacturing system and its potential reconfigurations1 some authors tried to use the concept of ‘‘real option’’ in order to represent the potential for a production resource to be reconfigured sometime in the future. Bengtsson and Olhager (2001) used the concept of Real Option to represent the capability of a flexible system to be easily and cost-effectively adapted to different and new part mix compositions. Kulatilaka (1988) tried to capture the value of flexibility by valuing the opportunity for a flexible system to be reconfigured so as to easily switch to a new operating mode. He developed a model by using the Bellman equation of dynamic programming to establish which the optimal mode to operate at each time step was, given a system configuration and its potential operating modes with related switching costs. However, this model assumed that all the sources of uncertainty – as type of product, material, product geometry, etc. – were integrated within one source affecting the underlying asset. Then, the paper tackled the production problem by considering a simplified part mix as composed of two part types. However, when moving to a practical context, this approach becomes complex to be used and, most of all, understood. The many sources of uncertainty that affect a manufacturing system and the increasing computational complexity of the model when the number of variables increases (i.e. the part mix wideness) are the main elements that hinder the applicability of the ‘‘real option’’ approach to this problem, an approach which on paper would seem the most appropriate one to be used. Apart from this aspect, the use of this model applied to a complex real case generates as much complex results that are difficult to be understood and therefore hard to be proposed to a manufacturing company. This chapter tries to bridge the gap present in literature and proposes an approach for supporting life-cycle decisions, which may at the same time capture the complexity of the manufacturing environment and still be simple enough to be applied by practitioners. To this purpose, it introduces mathematical programming models which can lead to an evolutionary manufacturing system solution that optimizes expected profit over a multi-period time horizon. This work is addressed to the system user in supporting his interaction with the machine tool builder, and the decisions he must take among the set of possible choices laid out by the latter. Therefore, the valuation model supports the decision making process that the system user has to accomplish in order to choose the kind of system configuration to acquire and to plan for its future potential upgrades. In the context of a small-medium enterprise (SME), the 1

In order to have a major insight into the reconfiguration concept, please refer to Matta et al. (2008).

196


typical user of this model would be the upper management of the company, eventually supported by a consultant. In the case of larger firms, it could be a working group with representatives from production and finance. In this latter case, the model described in Chap. 5 would be targeted to top management, while the model discussed in this chapter would have production managers as main users. The information required by this model derives from results emerging from the previous chapters of this book. Chapter 5 introduces the model that the system user utilizes to define the expected scenarios for its relevant production variables and represent them through a scenario tree (Tolio and Valente 2007; Cantamessa et al. 2007). Chapter 6 describes the manufacturing technology while Chap. 7 provides alternative solutions offering different degrees of flexibility. The chapter follows the usual ‘‘system user vs. machine tool builder’’ framework according to the interaction setting described in Chap. 1. It formalizes the user’s objectives and constraints and supports it throughout the system acquisition process, while taking for granted all the inputs deriving from the previous models. In order to capture the real-world context of a manufacturing company, the model assumes that the client is already producing and selling goods on the market and has a manufacturing system that in a sense competes with the new proposed solutions. This means that – at the limit – the optimal solution suggested by the model could be not to invest at all and keep on producing with the legacy system. The model includes some budget constraints and a risk aversion parameter (i.e. the profit discount rate) that can affect purchasing decisions. Moreover, the model also allows to consider a technological pathdependency, which is important since this element arose quite clearly from the empirical evidence in Chap. 2. Switching from one solution to another one does not come for free, or with a cost which is simply equal to the additional investment in machinery. To this purpose, the model considers both generic switching costs (which can include factors such as training, decommissioning, etc.) and an initial inefficiency due to learning curve associated with operating new machinery. Other elements affect both positively and negatively the final outlay as the variable costs and the recovery value of the current system. In fact, and as shown in Chap. 2, many firms prefer to maintain the current manufacturing system and handle uncertainty or changes in part mix or demand with different ways, such as outsourcing. Figure 8.1 shows input and output for the valuation model. The model processes all these inputs and generates a multi-period solution. It indicates the system solution to be acquired at the first time stage, the system reconfigurations to be operated the future time stages, and the related economic performance. These results are useful to support the system user in planning the system life-cycle and avoiding misalignments and problems that have been discussed in Chap. 2.


197

Fig. 8.1 Valuation model structure

8.3 The Valuation Model Structure The valuation model is structured in two basic models: a Static Model and a Sequential Model. The first one considers the system performance as the manufacturing costs associated with a specific instance of the [scenario node – system configuration] set: it minimizes such costs while does not consider the time variable. Given a scenario node, s1, and given a configuration, c1, the Static Model returns the expected optimal manufacturing costs of c1 under the scenario node s1. It is important to notice that sj represents the jth element of the scenario tree and is not time-dependent. The second model (i.e. the Sequential Model) includes the time axis and divides it in discrete buckets. The model aims to identify the investment path that optimizes the trade-off between the expected investment and the operational costs along the time horizon. It guides the purchaser through the available configurations and points out those ones that come with the least overall expected costs under the expected demand scenarios. Therefore, the output is a set of solutions that is optimal from the aggregate standpoint instead of a set of locally optimal solutions. Both the time and the influence of previous choices lead to include the path-dependency phenomenon in the model so as to be more consistent with real manufacturing system configuring problems. In order to better clarify this concept, two cases are considered as extreme scenario: in the first case, it is assumed to have negligible switching costs while, in the second case, it is assumed to have very high switching costs. In the first case the Sequential Model will suggest selecting, at any time stage, the manufacturing system configuration that optimizes operational performance at each time stage, as if there was no dependence among time stages. In the second case the Sequential Model would suggest selecting the system configuration that makes the averaged best performance over all potential scenarios, and keeping on with that over the all planning horizon. In this latter case, it is likely that the configuration selected would not maximize the performance at any time stage

198


(as it was with no switching costs), but it would maximize the performance over the multi-period horizon as it takes into account the switching costs as well. The two problems have been developed as Mixed-Integer Linear Programming models to plan the basic machine to be selected on multi-period time by a deterministic setting. Figure 8.2 shows the process layout to define a valid planning and valuation model, moving from the static to the dynamic one. The Static Model receives two inputs: the sets of scenario nodes and the sets of alternative configurations. The first input is elaborated internally by the system user that is the addressee of this chapter. Chapter 5 describes how the system user should generate a set of scenarios based on some uncertainty variables (part mix and volumes) and company manufacturing strategies (i.e. focalization, differentiation and diversification). Each scenario is characterized by a production problem in terms of part mix composition and volumes to be produced, plus some geometrical and technological peculiarities. The second input derives from the interaction between the system user and machine tool builder. Once the system user has a projection of the expected demand scenarios, it submits this information to the machine tool builder, who develops a set of manufacturing system configurations. Each configuration is able to process a portion of a demand scenario according to the boundaries and the optimizing criteria set by the machine tool builder. This admissible production domain is expressed in terms of linear constraints and can be represented as a polyhedron region of part mix quantities that can be produced (see Sects. 4.5 and 7.4.4; Tolio and Valente 2007, 2008; Fig. 8.3 for a graphical representation). Chapter 4 has described how problem information has been formalized and Chap. 7 has introduced the system design process from the machine tool builder side. It is worth highlighting that each configuration can be a suboptimal solution for the client because it has been formulated and planned according to the machine tool builder’s optimizing criteria as well. The Static Model processes these inputs and individually considers each [scenario node – configuration alternative] instance, and generates two outputs. The first one is composed of the costs sustained by the system configuration to process the production problem paired off with each scenario node. Performance are then stored in the Performance Matrix. The second output is the set of costs to switch from a configuration to another one. These costs are stored in a Switching Costs Matrix.

Fig. 8.2 Valuation model process


199

Fig. 8.3 Inputs and outputs from the static model

The Static Model outputs are then loaded into the ‘‘Performance Matrix’’ (PM) and the ‘‘Switching Costs Matrix’’ (SM) of the Sequential Model. In addition, the ‘‘Sequential Model’’ receives the information about the scenario tree in terms of occurrence probability for each scenario node as input (see Chap. 5 for an insight into the generating scenario node process). The outcome leads to determine the optimal evolution of the system over the planning horizon (see Fig. 8.4 for the Sequential Model process).

8.4 Sets of the Valuation Model The following sections will show how the static and sequential models have been formulated in terms of data, objective functions and constraints. Table 8.1 describes the indexes that will be used from now on.

8.5 Static Model The aim of the Static Model is to calculate the parameter bi,j that is the system performance as manufacturing cost sustained by configuration i to face the production problem related to the scenario node j. Then, the model calculates the parameter cw,i, that is the cost to switch from a configuration w to another

200


Fig. 8.4 Inputs and outputs from the sequential model

i in two subsequent time stages. The performance value comes from solving a minimum cost optimization problem including part mix demanded by the market, manufacturing capacity, production costs, and outsourcing and lostsales penalty costs. Switching costs are calculated by solving a simple expression comparing two configurations in terms of number of available resources by alternative. Table 8.1 Sets for the valuation model Index Definition t i, w p s j k

Time stages {1,. . .,T} System configurations {1,. . .,M} Part types of the mix {1,. . .,Q} Type of resources per configuration i {1,. . .,R} Scenario nodes {1,. . .,N} Sub-scenarios for each performance value {1,. . .,K}


201

8.5.1 Performance Matrix This section shows how the performance matrix is developed in terms of initial assumptions, data, decision variables and final formulation. The assumptions are as follows:

The system can produce internally a quantity zi,s,p of part type p using manufacturing machine s of configuration i as well as outsource production or undertake a penalty cost due to lost demand; Each configuration i is formalized as a linear constraint: given a part mix, a volume per part type p of the mix, and a configuration i including s manufacturing resources, the quantity that can be processed by a configuration depends on the hyperplane coefficient2 of each resource. Parameters are defined in Table 8.2. The decision variable is reported in Table 8.3. The problem objective function is then formulated as follows: BBasej;i ¼ MIN

nX o z CPI þ D z PCS ; j;i;p i;p j;t;p j;i;p p p

8i; j

(8:1)

Where BBasej,i is the performance of configuration i in facing the production problem associated with scenario node j. This value will be integrated with the ‘‘Sequential Model’’ in order to load the ‘‘Performance Matrix’’ as follows: Bj;k;i ¼ BBasej;i #k

(8:2)

Where the parameter k is a multiplicative coefficient that indicates the updown movements for each performance value and is used to set different cases, ranging from pessimistic to optimistic (BBasei,j,t is the most likely case). When k is equal to 1, the problem is set on the base case. The optimistic case is given by the opportunity to improve the performance value (considering k 1). The objective function is subject to the following boundaries: X

i;s;p 1 þ ru coeffi;s;p NEWp;j;t zp;j;i i;s AVAILi;s ;

8s; i; j; t

(8:3)

p

This constraint refers to the capacity boundaries for each resource s to produce part type p, for each configuration i at any scenario node j. The capacity constraint defines the admissible area for the configuration: constraints are supposed not to refer to each physical resource s, but to each type 2

The hyper-plane coefficient is the operational time the resource s needs to complete a unit of product p of the mix.

202


Table 8.2 Model parameters Parameter Definition Dp,j CPIp,i MMCp,s,i PCSp i,s,p i,s PENp COUTp AVAILi,s Ru_coeffi,s,p

NEWp,j,t CUs,i k BBasej,i Bj,k,i

Demand of part type p at scenario node j Internal production costs associated with the production of part type p using the configuration i Cost sustained by resource s of configuration alternative i to work part type p of the mix Costs associated with the part of demand unsatisfied by internal production for part type p Hyperplane coefficient of resource s of configuration alternative i to produce part type p of the mix Capacity boundary (right-hand side) of resource s of configuration i, in terms of total working time supported by each resource Penalty costs whether it is produced less than demand for part type p Outsourcing costs associated with producing (a part) of part type p externally Availability as number of available resources s in the configuration i Additional time (expressed as a portion of normal hyperplane coefficient i,s,p) required by resource s of configuration alternative i to ramp up each part type p when it is introduced for the first time. The chapter assumes that this additional time is sustained only for one time bucket (i.e. the first period in which a new part type p is introduced in the mix) Is a Boolean variable and is equal to 1 if part type p is newly introduced under scenario j at time stage t, otherwise it is equal to 0 Cost units sustained by resource s to work any part type p for a time unit by using the configuration i Multiplicative coefficient that indicates the k-th up-down movements for each performance value Base performance of configuration i in facing the production problem associated with scenario node j kth occurrence of performance of configuration i in facing production problem associated with scenario node j

of resource (i.e. if two physical manufacturing machines are equal, the righthand of the constraint expression is twice as large). PCSp is the cost associated with the demand part for part type p that has not been satisfied by internal production. Its value is given by the following expression: PCSp ¼ MIN COUTp ; PENp ;

8p

(8:4)

It is the minimum between producing externally costs (outsourcing solution) or undertaking penalty costs (unsatisfying demand solution). Table 8.3 Decision variable Variable Definition zp,j,i

Quantity that can be internally produced for each part type p of the mix given the scenario node j and using configuration i


203

CPIp,i is the total working cost to produce internally a single unit of part type p of the mix. The value is given by expression 8.5: CPIp;i ¼

X

MMCs;i;p ;

8p; 8i

(8:5)

s

It is the sum of costs sustained by all the s resources of each configuration i to produce a single unit of part type p. Therefore: MMCs;i;p ¼ s;i;p CUs;i ;

8s; 8i; 8p

(8:6)

8.5.2 Switching Costs Matrix In addition to the ‘‘Performance Matrix’’, the Sequential Model receives the ‘‘Switching Costs Matrix’’ from the Static Model as input. Each cell of the Switching Costs Matrix is the cost to be sustained if the system user switches from a configuration to another one when moving to the next time stage. As obvious, there are zero values on the main diagonal of the matrix. The matrix elements can be either positive or negative (costs): they are positive whether switching from the configuration set in the matrix rows to a new configuration set in the matrix columns requires an additional investment (e.g. the purchase of an additional resource). On the other hand, the elements of the matrix are negative when the switching between two different configurations requires to disinvest (i.e. to dismiss resources). In the latter case, the value is negative since firm can sell the additional resource and at least partially recover the value. Switching costs are calculated by solving the following expression (8.7) which compares two configurations in terms of number of available resources in each configuration. By detail, cw,i is the cost to switch from configuration w to a new i. Therefore, it is:

equal to the investment in purchasing the additional resources of the alternative i when moving from configuration w to i involves more machines;

equal to the gain from selling the additional resources of the alternative w, when moving from configuration w to i. In this case, it would be reported as a negative value. Parameters are defined in Table 8.4. Table 8.4 Model parameters Parameter Definition AVAILi,s ICs gains

Availability expressed in terms of number of available resources s in the configuration i Investment cost required to purchase an additional unit of resource type s Return on investment from selling a unit of resource type s. It is assumed that this share is constant for each resource

204


The problem has been formulated as follows: lcw;i ¼

X MAX 0; AVAILi;s AVAILw;s ICs þ s

X

MAX 0; AVAILw;s AVAILi;s ICs gain ;

(8:7) 8w; i

s

8.6 Sequential Model The second step of the valuation model is to develop the ‘‘Sequential Model’’. The aim is to optimize the configuration investment trajectory over the time horizon by minimizing the expected cost to reply to the demand scenarios that can randomly arise. The assumptions for the sequential model are as follows:

Each performance is associated with a configuration i while each scenario node j is uncertain. In order to represent this uncertainty, it is assumed that three sub-scenarios are possible (index k = 1, . . ., 3): – Pessimistic case bi,j,1 = BBasej,i*1 , with 1 >1; – Base (most likely) case bi,j,2 = BBasej,i*2 , with 2 =1; – Optimistic case bi,j,3 = BBasej,i*3 , with 3 > < t j i k xi;t PSSk ð1þrÞt PSj;t þ = hP P P i MIN Cw;i RU Ci;t > > ; : t þ t t w i yt;w;i ð1þrÞ

(8:8)

ð1þrÞ

The objective function is subject to the following constraints: X i

xt;i ¼ 1;

8t

(8:9)


205

Table 8.5 Model data Data Definition PSj,t Cw,i Bi,j,k

PSSk r Ru_coeffi

RU_Ci,t

BUDGETt BUDGET_TOT

Occurrence probability for each scenario node j at any time stage t Switching costs from configuration w to i. At the start, these costs can be negative (e.g. if the change implies the sale of a resource) Performance Matrix with sub-scenario k of performance (manufacturing cost) for configuration i in facing scenario node j. The calculation of this parameter was discussed in the previous section Where k = 1,...,K is the index that runs over the occurrences of each performance (pessimistic case, most likely case and optimistic case) Six-monthly discount rate System ramp-up coefficient. We assume that its value is a portion of the performance of a given configuration and that this ‘‘penalty’’ is sustained by the system only for one time bucket (i.e. the first period in which system switches from a configuration alternative w to another, i.e. the new configuration i) Additional cost sustained by the system if the user switches from a configuration w to a new one i at time stage t. This cost is related to the ramp-up associated with the system Available budget by the firm at any time stage t Total amount of available budget in the firm

xt;i 2 ½0; 1; yt;i;w 2 ½0; 1;

8t; i

(8:10)

8t; i; w

(8:11)

yi;w;t xt1;w þ xt;i 1; 8t; i; w X X RU Ci;t ¼ B PSSk PSj Ru coeffi ; j k i;t;j;k X X i

w

yt;w;i Cw;i BUDGETt ;

X X X t

i

w

8t

yt;w;i Cw;i BUDGET TOT

(8:12) 8t; i

(8:13) (8:14) (8:15)

The first constraint means that only one configuration is allowed per time stage. The second and third constraints, respectively, mean that both decision variables are binary variables. The third constraint is related to the switching

Table 8.6 Decision variables Variable Definition xi,t yt,i,w

Is equal to 1 if configuration i is selected at time t, 0 otherwise Is equal to 1 if at time stage t system is switched from configuration w to a new configuration i, 0 if at time stage t there is no switch from a configuration to another one (i.e. index i is equal to w)

206


variable: it is equal to 1 if index i – that is the configuration selected at time stage t – is not equal to w – i.e. the configuration used at the previous time stage (t-1). The fourth constraint is related to the worsening performance, expressed in terms of increasing cost associated with configuration i arising from the rampup coefficient for a new configuration. This cost is sustained only when system switches from configuration w to a new alternative i (i.e. the value of switching variable yt,i,w = 1). Finally, the latest two constraints are related to the firm budgetary availability, respectively, at any time stage and over the all time horizon.

8.7 Model Testing This section describes an experimental run on the valuation model and an analysis applied to budget, outsourcing cost and system ramp-up parameters.3 The purpose is to show how the model works and what results it returns when some parameters are modified. The model testing has been run on a five year time horizon with a half-year time step – therefore it comes with ten time buckets. The process starts from the Static Model that receives the information about the set of scenario nodes (in a form of scenario tree, Fig. 8.5) – that has been elaborated internally by the system user – and the set of alternative configurations – that has been elaborated by the machine tool builder. This latter comes

Fig. 8.5 Scenario tree pattern

3

The model has been written, performed and validated with the Lingo Solver software (version 7.0). Microsoft .NET Framework 2.0 configuration, Microsoft Visual Studio 2005, and Microsoft Office Access 2003 have been used to develop user interfaces and run all the modules in close integration with the modules described in other chapters of the book. The final application has been run on a PC with an Intel Pentium M 740, 1.73 GHz CPU; 512 MB memory.


207

Fig. 8.6 Configuration tree pattern

as a tree as well (‘‘configuration tree’’, Fig. 8.6) and shows the reconfiguration path laid out by the machine tool builder. Figure 8.5 shows the scenario tree elaborated by the system user. Each scenario node is a production problem expressed in terms of part mix (the current example includes two part types in the mix: part type ‘‘a’’ and part type ‘‘b’’) and part type volumes. Table 8.7 reports part type volume details deriving from the scenario tree as Fig. 8.5 shows. The first column reports all the scenario nodes starting from the root and progressively numbering all the further ones – that are expressed as ‘‘sn_1’’, ‘‘sn_2’’, etc. Table 8.7 Part type volumes Scenario Part type ‘‘a’’ Part type ‘‘b’’ node volumes [units] volumes [units]

Scenario Part type ‘‘a’’ node volumes [units]

Part type ‘‘b’’ volumes [units]

Root Sn_1 Sn_2 Sn_3 Sn_4 Sn_5 Sn_5 Sn_6 Sn_7 Sn_8 Sn_9 Sn_10 Sn_11 Sn_12 Sn_13 Sn_14 Sn_15 Sn_16 Sn_17

Sn_18 Sn_19 Sn_20 Sn_21 Sn_22 Sn_23 Sn_24 Sn_25 Sn_26 Sn_27 Sn_28 Sn_29 Sn_30 Sn_31 Sn_32 Sn_33 Sn_34 Sn_35 -

4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 0 0 4000 4000 0 0 -

4000 4168 4168 4134 4134 4334 4334 4268 4268 4500 4500 4400 4400 4668 4468 4534 4534 4834 4834

4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000

4668 4668 5000 5000 4800 4800 5168 5168 4800 4800 5334 5334 4800 4800 5500 5500 4800 4800 -

208


Figure 8.6 shows the configuration tree developed by the machine tool builder. The values on the arcs are the investment to be sustained to move from a configuration to another one (expressed in terms of Cost Units). Each configuration involves some resource types and a number of resources per type. Table 8.8 reports the machine and carrier resources characterizing the FFMS configurations at each node. Values and variable names have been simplified to be read more easily. Column ‘‘Rhs’’ in Table 8.8 refers to the capacity constraint for each type of resource that is the right-hand side of the expression (8.3) while left-hand side defines the time required by each part type to be produced by each resource. Tables 8.9 and 8.10 report this last information. Considering the set S of part mix scenario nodes as Table 8.7 shows, with S2{s1,s2,. . .,sj,. . .,s37}, and the set C of configurations illustrated in Table 8.8, with C2{c1,c2,. . .,ci,. . .,c9}, the Static Model returns the performance value of configuration ci under the scenario node sj for each set {sj,ci}. The performance value comes from solving the minimum cost optimization problem defined by the expression (8.1). According to its formulation, the Static Model returns the cost of using a system configuration to produce as much internally as it is allowed by its capacity constraints and outsourcing the unsaturated demand quote (refer to expressions (8.4) and (8.5)). The Static Model returns the switching costs per configuration couple as well. According to Sect. 8.5.2, switching costs are calculated by solving the expression (8.7) which compares two Table 8.8 Features per configuration Node Configuration

Type of resource

Number of resources

Rhs

Root Root 1 1 2 2 3 3 4 4 5 5 5 6 6 6 7 7 8 8

Carrier 01 Machine 07 Carrier 01 Machine 07 Carrier 01 Machine 07 Carrier 01 Machine 07 Carrier 01 Machine 07 Carrier 01 Machine 02 Machine 07 Carrier 01 Machine 02 Machine 07 Carrier 01 Machine 07 Carrier 01 Machine 07

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

5142.89 7200 5142.85 7200 5142.85 7200 5142.85 7200 5142.85 7200 5142.85 7200 7200 5142 7200 7200 5142.85 7200 5142.85 7200

FFMS (c1-root) FFMS (c1-root) FFMS (c1-node1) FFMS (c1-node1) FFMS (c1-node2) FFMS (c1-node2) FFMS (c1-node3) FFMS (c1-node3) FFMS (c1-node4) FFMS (c1-node4) FFMS (c1-node5) FFMS (c1-node5) FFMS (c1-node5) FFMS (c1-node6) FFMS (c1-node6) FFMS (c1-node6) FFMS (c1-node7) FFMS (c1-node7) FFMS (c1-node8) FFMS (c1-node8)


209

Table 8.9 Working time and cost per configuration (part 1) Part type Configuration Resource Working time

Working cost

A A A A A A A A A A A A A A A A A A A A

0.667 4.615 0.667 4.615 0.667 4.615 0.667 4.615 0.667 4.615 0.889 1.657 1.395 0.889 1.657 1.395 0.667 4.615 0.667 4.615



0.013 0.093 0.013 0.092 0.013 0.092 0.013 0.092 0.013 0.092 0.018 0.033 0.028 0.018 0.033 0.028 0.013 0.092 0.013 0.092

Table 8.10 Working time and cost per configuration (part 2) Part type Configuration Resource Working time

Working cost

B B B B B B B B B B B B B B B B B B B B

0.625 4.013 0.625 4.013 0.625 4.013 0.625 4.013 0.625 4.013 0.625 0.00 4.013 0.625 0.00 4.013 0.625 4.013 0.625 4.013



0.012 0.080 0.012 0.080 0.012 0.080 0.012 0.080 0.012 0.080 0.012 0.00 0.080 0.012 0.00 0.080 0.012 0.080 0.012 0.080

210


Table 8.11 Investment costs per resource type Type of resource Investment cost (cost units) Carrier 01 Machine 02 Machine 07

30.97 131.00 187.00

configurations in terms of number of available resources per configuration. The needed information are included by Table 8.8 (i.e. in ‘‘Number of resources’’ column) while Table 8.11 contains the information about the investment required by each machine and carrier resources. Next, the second step of the Valuation Model is the Sequential Model, whose structure has been presented by Sect. 8.6 of this chapter. It receives both the performance and the switching costs matrixes as inputs from the Static Model, and the information about the occurrence probability for each scenario node that are from the scenario tree pattern (Fig. 8.5). Moreover, it receives the budget availability and the discount rate for each time stage t, as illustrated in Table 8.12. The Sequential Model outcome is the optimal evolution of the system over the planning horizon and derives from solving the minimum cost optimization problem illustrated in expression (8.8). Table 8.13 shows the outcome. Considering that the starting configuration is FFMS (c1-root), the model suggests that the optimal choice be to switch at time stage t = 1 from configuration FFMS (root-c1) to FFMS (Reconfiguration-c1-5) and keep on with this configuration over the entire planning horizon.4 Switching from FFMS (root-c1) to FFMS (Reconfiguration-c1-5) comes with a required investment (131.00 CUs)5 and is possible since the budget constraint (expression 8.14) at time stage t = 1 is satisfied.6 The final total cost related to this choice is 63734.43 CUs.7

Table 8.12 Budget constraints and discount rates for each time stage Time 1 2 3 4 5 6 7 8

9

10

Budget Rate

10000 1

2300 12

4

2000 2

3000 3

4000 4

2000 5

3000 6

5000 2

6000 3

5600 2

Outsourcing costs for both products of the mix are equal to 1300 CUs. In fact, by making a comparison between the two configurations (i.e. FFMS (root-c1) and FFMS (Reconfiguration-c1-5)), an additional type of resource ‘‘Machine 02’’ (see Table 8.9) is present in the new configuration FFMS (Reconfiguration-c1-5). Its investment cost is equal to 131.00 CUs, as illustrated in Table 8.11. 6 In fact, the investment cost related to configuration FFMS (Reconfiguration-c1-5) is 131.00 CUs and is lower than budget the availability at time stage t =1, i.e. 2000 CUs (see Table 8.12). 7 System value is calculated as the sum of discounted performance values over the planning horizon. 5


211

Table 8.13 System planning over 10 time stages Time stage Optimal configuration 1 2 3 4 5 6 7 8 9 10

FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5) FFMS (Reconfiguration-c1-5)

A sensitivity analysis has been performed on budget constraints, outsourcing costs and system ramp-up coefficients, varying just one of them and keeping the others out of the run. Results are worthy to see how the model – and the final outcomes – reacts to some parameter modifications. The budget parameter has been varied as first: a new stream of budget constraints has been set as illustrated in Table 8.14 – that is setting budget to zero at the first time stage. Based on this budget, the firm is not able to change the system configuration at the first time stage and therefore is forced to keep on with the starting configuration unless there is a no switching cost configuration. The new output is shown in Table 8.15: Considering that the starting configuration is FFMS (root-c1), it means that the optimal choice is to switch, at time stage t = 1, from configuration FFMS (root-c1) to FFMS (Reconfiguration-c1-2), and given that it is the same as FFMS (root-c1) (refer to Tables 8.8, 8.9 and 8.10), the switching comes for free. At time stage t = 2 the model leads to switch from configuration FFMS (Reconfiguration-c1-2) to FFMS (Reconfiguration-c1-6) (where the investment required is 131.00 CUs) and to keep on with this configuration over the entire planning horizon. This switching is possible since budget availability at time stage t = 2 is equal to 3000 CUs. The system cost related to this new choice is 65840.15 CUs. It is higher than the first case (i.e. 63734.43 CUs) because, at time stage t = 1, the selected configuration is FFMS (Reconfiguration-c1-2) whose performance is greater (i.e. greater manufacturing costs) than the FFMS (Reconfiguration-c1-5) one. A second run has been performed by setting all the budget constraints to zero as Table 8.16 illustrates below. In this case, it is expected to keep on with the same configuration over the all time horizon or, at last, to switch towards a free Table 8.14 Zero budget at time 1 Time 1 2 3 4

5

6

7

8

9

10

Budget

3000

5000

6000

5600

10000

2300

0

3000

4000

2000

212


Table 8.15 System planning over 10 time stages – zero budget case at t = 1 Time stage Optimal configuration Time stage Optimal configuration 1 2 3 4 5

FFMS (Reconfiguration-c1-2) FFMS (Reconfiguration-c1-6) FFMS (Reconfiguration-c1-6) FFMS (Reconfiguration-c1-6) FFMS (Reconfiguration-c1-6)

6 7 8 9 10


switching system configuration otherwise the budget constraint in expression 8.14 would not be satisfied. The new output related to this situation is illustrated in Table 8.17: As expected, the Sequential Model returns the same configuration over the entire planning horizon. Considering that the starting configuration is FFMS (root-c1), this means that the optimal choice is to switch, at time stage t = 1, from configuration FFMS (root-c1) to FFMS (Reconfiguration-c1-4) due to zero switching costs. The final total cost related to this new solution is 75748.55 CUs and is higher than the first two cases because there are more tightened constraints. It is worth showing that, as soon as the budget constraint turns to be positive sometime on the horizon,8 for instance at time stage t = 5, the model would suggest that the user switches towards a lower costly configuration. Indeed, if the available budget at time stage 5 is 3000 CUs, the model points out to switch to the solution FFMS (Reconfiguration-c1-5) as it costs only 131.00 CUs, and to keep on with it as further time steps are again limited by a zero budget. In this case, the total system cost would be 69444.37 CUs that is lower than the no budget case at all. Sensitivity analyses have been then performed on the outsourcing cost parameter. The expected outcome must be a total cost trend such as in Fig. 8.7. Considering outsourcing costs on x-axis and total costs on y-axis, and considering a fixed part mix quantity to produce, total costs are directly proportional to outsourcing costs until these last ones are equal to internal costs. From the break even cost point on, total costs decrease their slope given that are made of internal costs up to the capacity constraints and outsourcing cost to cover the unsaturated demand. Table 8.16 Zero budget at all time stages Time 1 2 3 4

5

6

7

8

9

10

Budget

0

0

0

0

0

0

8

0

0

0

0

Budget availability must be also larger than the investment required by switching towards a new higher performance configuration (i.e. lower manufacturing costs).


213

Table 8.17 System planning over 10 time stages – zero budget case at all time stages Time stage Optimal configuration Time stage Optimal configuration 1 2 3 4 5


6 7 8 9 10


The sensitivity analysis has been applied by considering both the unbounded9 and bounded capacity cases, and confirmed the expected results. In the first case, outsourcing costs have been varied from 700 CUs up to 1300 CUs with a 10 CUstep and total costs varied according to a positive first derivative and a negative second derivative. Results are graphically shown in Fig. 8.8. When outsourcing costs are equal to 950 CUs, total costs stop to increase because the breakeven point has been reached for both part types a and b, and the entire production is accomplished internally. Zooming in on the breakeven area, it is worth highlighting that internal manufacturing machineries for part type a become cost-effective from 939.42 outsourcing CUs on while for part type b from 946.38 CUs on. As Fig. 8.9 shows below by zooming in on these points, the slope of total cost function changes twice according to a double internal-external costs matching.

Fig. 8.7 Total cost vs. outsourcing costs

9

It has been rendered by setting a large manufacturing capacity.

214


Fig. 8.8 Sensitivity analysis on outsourcing costs (unbounded capacity)

In the second case, it has been assumed that the configuration FFMS (c1-root) was available by setting an end-less ramp-up coefficient for the other configurations: the analysis has been run on an up to 2000 CUs range and results are as shown in Fig. 8.10. When outsourcing costs 946.38 CUs, it becomes more costeffective to produce part type b internally and it does the same for part type a when outsourcing passes 1252.82 CUs. From this point on (named B on Fig. 8.10), total costs continue to increase because the internal system is not capable to process all the demand, and the residual demand quote is given outside the firm. Sensitivity analysis has finally been run on the system ramp-up coefficient that is the additional cost that a new configuration entails during the launching phase. It has been quantified as a percentage of the total cost performance of a new system or its reconfiguration, and is considered just for the first time stage by which the system is introduced. All previous model runs adopted a system ramp-up coefficient equal to 0.1. By varying it, the switching path can change over the time period because the final outcome changes. The analysis has been performed by assuming that only three system configurations are available.10

Fig. 8.9 Sensitivity analysis on outsourcing costs – zooming in (unbounded capacity)

10

This simplification is due to the fact that FFMS (Reconfiguration c1-1), FFMS (Reconfiguration c1-2), FFMS (Reconfiguration c1-3) and FFMS (Reconfiguration c1-4) are equivalent to FFMS (root-c1) while FFMS (Reconfiguration c1-5) is equivalent to FFMS (Reconfiguration c1-6) and FFMS (Reconfiguration c1-7) is equivalent to FFMS (Reconfiguration c1-8) (see Tables 8.8, 8.9 and 8.10).


215

Fig. 8.10 Sensitivity analysis on outsourcing costs (bounded capacity)

FFMS (c1-root), FFMS (Reconfiguration c1-5) and FFMS (Reconfiguration c1-7).11 Then, it has been assumed that the ramp-up coefficient is null for both configurations FFMS (c1-root) and FFMS (Reconfiguration c1-7) while outsourcing costs are equal to 1300 CUs so that producing internally is cheaper than outsourcing for both part types. Launching the model returns the FFMS (Reconfiguration c1-5) as the optimal solution because related internal costs are the lowest (Table 8.18). Next, the model has been launched on different ramp-up coefficients in order to have a major insight into the effects on the final system performance – that is always formalized in terms of total costs. The final solution sensitivity has been measured by varying the coefficient from 0 to 2 by a 0.1 step. Figure 8.11 shows the total cost function trend when the FFMS (Reconfiguration c1-5) ramp-up coefficient increases. Looking at Fig. 8.11, from 0 to 1.6, the total cost increases and the optimal system solution is FFMS (Reconfiguration c1-5) over the entire horizon. From 1.6 on, at time t = 1 and t = 2 the optimal configuration is (c1root) while from the third time stage on it turns to be FFMS (Reconfiguration c1-7). The same analysis has been accomplished by working on the ramp-up coefficient for FFMS (Reconfiguration-c1-7)12 and results are shown in Fig. 8.12. Table 8.18 Internal cost for both part types of the mix Part type FFMS (c1-root) FFMS (Reconfiguration c1-5) a b

11

1252.81 946.4

939.42 946.4

FFMS (Reconfiguration c1-7) 1252.81 946.40

As seen previously in this section, this is possible supposing an endless ramp-up coefficient related to the other configurations. 12 Please, remember that in Fig. 8.11 the ramp-up of FFMS (Reconfiguration c1-7) was null. In Fig. 8.12 ramp-up of FFMS (c1-root) is always null and ramp-up of FFMS (Reconfiguration c1-5) is 1.6.

216


Fig. 8.11 Total cost vs. ramp-up of configuration FFMS (Reconfiguration c1-5)

In this case, total costs grow when the ramp-up coefficient for FFMS (Reconfiguration c1-7) grows up to PI. At point PI, the ramp-up coefficient of FFMS (Reconfiguration c1-7) is so high that the model suggests selecting FFMS (c1-root) over the entire planning horizon. From point PI on the total cost function does not depend on the ramp-up coefficient of FFMS (Reconfiguration c1-7) anymore and is equal to 74868.87 CUs. Results from this model are of course limited by its simplicity. However, the sensitivity analysis on three main parameters – budget constraint per time stage, outsourcing costs and system ramp-up coefficient – laid out some performance curves that are consistent with the expected results. Due to this empirical evidence, the valuation model as has been developed in this chapter is valid and reliable, and can be used to solve manufacturing system life-cycle planning problems, including those real-world parameters that strongly affect the decision-making process.

Fig. 8.12 Total cost vs. ramp-up of configuration FFMS (Reconfiguration c1-7)


217

8.8 Conclusions According to previous sections, this chapter tackled the problem for a system user of planning the manufacturing system life-cycle over a given medium-term horizon. As Chap. 2 showed, the empirical evidence made clear that manufacturing small to medium-sized firms are in trouble when have to deal with machine tool builders in defining, negotiating and purchasing the manufacturing system that includes the flexibility and capacity degree they are looking for. Some misalignments between machine tool builder’s and system user’s perspectives usually tend to make both players to convey to a final solution that is not optimal for both. In addition, due to some inefficiency within the user organization – i.e. operational decisions are not aligned to and consistent with strategic decisions – the system user is often not satisfied by the decision because it is not exactly what he/she wanted and/or is not capable to execute it. In turn, this can lead to losing either profitability or demand. Using the valuation model that has been presented in the current chapter, the system user can make some breakthroughs as it holds an easy-to-use tool to assess and plan a manufacturing system investment. By using it, the user can assess a single solution and find out how much further upgrades would cost or can compare several bids from different machine tool builders or, once more – as it is assumed in this chapter – it can handle a more complex situation where the machine tool builder draws up a multi-solution commercial bid. This valuation model would be then useful to better appreciate the focused flexibility concept embedded in some manufacturing solutions, by interactively observing the effects of alternative solutions that differ with respect to switching costs and manufacturing performance. In the end, some further developments are pointed out to improve this model and its applicability to the entrepreneurial world. It should be investigated how to introduce dynamic programming methodologies in order to handle more complex problems, i.e. a broader part mix, a major granularity for time steps, more potential decisions. In terms of contents, it should be investigated how to adapt the ‘‘Real Option’’ concept to the problem complexity and find the acceptable trade-off between reality approximation and simplicity of results. As known, the mentioned approaches to the problem are interesting and also aligned with most of the scientific studies in this field. However, the problem of overcoming their computational and usability complexity still must be solved and hindered their diffusion among manufacturing entrepreneurs so far.

References Bengtsson J, Olhager J (2001) Valuation of product-mix flexibility using real options. Int J Prod Econ 74:213–224 Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceeding of the 4th intenrational conference on digital enterprise technology, Bath, UK, 19–21 September, pp 627–636

218


Cheng L, Subrahmanian E, Westerberg A W (2003) Design and planning under uncertainty: issues on problem formulation and solution. Comput Chem Eng 27:781–801 Choi S, Kim J (1998) A study of measurement of comprehensive flexibility in manufacturing systems. Comput Ind Eng 34(1):103–118 Elkins D A, Huang N, Alden J M (2004) Agile manufacturing systems in the automotive industry. Int J Prod Econ 91:201–214 Kulatilaka N (1988) Valuing the flexibility of flexible manufacturing systems. IEEE Trans Eng Manag 35(4):250–257 Matta A, Tolio T, Karaesmen F, Dallery Y (2001) An integer approach for the configuration of automated manufacturing systems. Robot Compute Integr Manuf 17:19–26 Matta A, Tomasella M, Valente A (2008) Impact of ramp-up on the optimal capacity reconfiguration policy. Int J Flex Manuf Syst 19(3):173–194 Perrone G, Amico M, Lo Nigro G, Noto La Diega S (2002) Long term capacity decisions in uncertain markets for advanced manufacturing systems incorporating scope economies. Eur J Oper Res 143:125–137 Tolio T, Valente A (2006) An approach to design the flexibility degree in flexible manufacturing system. Proc of Flex Autom & Intell Manuf Conf, Limerick, Ireland, June 25–27, 2006, pp 1229–1236 Tolio T, Valente A (2007) A stochastic approach to design the flexibility degree in manufacturing systems with focused flexibility. Proceedings of DET2007 – international conference in digital enterprise, Bath, UK, 19–21 September, pp 380–390 Tolio T, Valente A (2008) A stochastic programming approach to design the production system flexibility considering the evolution of the part families. To appear in Int J Manuf Technol Manag – Special Issue on Reconfigurable Manufacturing Systems Tolio T, Terkaj W, Valente A (2007) Focused flexibility and production system evolution. Proceedings of 2nd international conference on changeable, Agile, reconfigurable and virtual production. Toronto, Ontario, Canada, July 23–24, 2007

Chapter 9

System Performance Simulation and Analysis Antonio Grieco and Francesco Nucci

Abstract The performance evaluation of different system architectures and the development of tailored methods to manage FFMSs at operational level are the final decision activities of the design approach presented in this book. In this chapter a simulation theory-based tool is presented. The proposed tool is able to automatically simulate a set of different scenarios and to provide the necessary capability to compare the performance of FFMSs versus FMSs. Moreover, tailored methods to optimize the performance at operational level are introduced in the simulated supervisor of the FFMSs architecture. The methods allow to split the execution of the part program among different machining centers and to manage the opportunity to share more than one pallet transport system on the same route. The methods are validated through simulation experiments. Keywords Discrete event simulation Performance evaluation Focused flexibility manufacturing systems – FFMS

9.1 Introduction to Manufacturing Systems Modeling This chapter introduces the different steps to develop a general tool based on simulation theory for the performance evaluation of FFMSs. Given the characteristics of the FFMS paradigm and the goal of comparing different solutions in terms of architecture and configuration, a very flexible simulation tool is necessary. Using this tool it is possible to test the goodness of the solutions proposed in Chap. 7 and related to systems characterized by focused flexibility, in comparison with alternative configurations belonging to the general paradigm of flexible manufacturing systems. F. Nucci (*) Dipartimento di Ingegneria dell’Innovazione, Universita` degli Studi del Salento, Lecce, Italy e-mail: [email protected]


219

220

A. Grieco and F. Nucci

Simulation is a wide known tool in the manufacturing field in order to assess system performance, see McHaney (1991), Pidd (1998) and Robinson (2004). There are numerous paradigms and tools which are capable of modeling various aspects of a system at different levels of detail. The problem of modeling new paradigms of production systems has been widely discussed in literature as reported by Averill et al. (2000), Zeigler et al. (2000), Banks et al. (2005), Lu and Wong (2007), Ryan and Heavey (2006) and Park (2005). In particular, simulation studies of process flow analysis in industrial plant have been investigated by Sivakumar and Chong (2001), Wohlgemuth et al. (2006) and Siemiatkowski and Przybylski (2006). Moreover, system configuration studies have been performed in order to select the most suitable resource allocation as addressed by Gien and Jacqmart (2005), Creighton and Nahavandi (2003) and Greasley (2008). Finally, various works deal with the FMS configuration problem in order to exploit the flexibility property in production systems (Toma et al. 1995; Tolio et al. 2001). The innovative aspect of the proposed work stands in the specificity of the systems considered as object of evaluation. It is important to notice that some characteristics of the focused flexibility systems, as reported in Cantamessa et al. (2007), have a great impact on the evaluation of system performance. Indeed the features concerning the FFMS configuration phase (see Chap. 7) will have to be effectively exploited within the simulation experimental campaign. Moreover, the FFMS solutions will be compared to the FMS solutions in order to evaluate the real benefits coming from customizing the system flexibility on the production requirements. This calls for an in-depth analysis of operative techniques for the resolution of scheduling problems on focused flexibility systems. Indeed, it is necessary to develop effective operational policies in order to fully exploit the features of the system architectures under analysis. For this reason, on the one hand, new methods and models suitable for FFMSs have been developed for the operational production management at the scheduling level. On the other hand, results available in the literature are included in the simulation models for traditional FMS systems. One important result of this chapter is that, by means of the developed simulation models, it will be possible to quantify the impact of flexibility on system performance. In order to fulfill such a necessity, two important issues have to be considered and introduced in the evaluation tool. First, the need of flexibility in a manufacturing system arises from the stochastic and dynamic nature of the operating environment. Sources of uncertainty are changes in demand (e.g. part types and part-mix) and resource availability (e.g. machine downtimes). In the proposed framework, all these features have been considered to develop a tool for the evaluation of the different architectures over different hypothesized scenarios. Second, different types of flexibility may be combined to provide different levels of performance for the considered manufacturing system. Consequently, the value of the aggregate flexibility cannot be straightforwardly obtained by combining the measures of its component flexibilities. In the proposed

9 System Performance Simulation and Analysis

221

framework, the evaluation of the different production architectures will be made taking into account the concept of aggregate flexibility via appropriate simulation models. Simulation tools are able to simulate the different configurations obtained as an input from the methods developed in Chap. 7. The design of the simulation experiments is affected by the output obtained from Chap. 8 where the production capacity acquisition plan is defined for the FFMS and for the FMS, under a certain set of economic and financial parameters. In the following section, a formal representation of the systems under study and the corresponding simulation model are introduced. In Sect. 9.3 the simulation model is validated taking into consideration a case study addressing the relationship between flexibility issues and system performance. Since the details of the system architectures under comparison may significantly influence the final results, the description of each single element considered in the simulation model assumes an important role. For this reason, the simulation model requires a formal description of the elements and of their interrelations which have been presented in Sect. 9.3. The formal model has been the basis for the implementation of the simulation one. In order to guarantee the features of generality and intelligibility to the formal model, the UML language has been adopted. At the end conclusions related with the tool validation phase are given.

9.2 Description of the Simulation Model Building Phases The goal of this chapter is to present the design of an environment for the evaluation of manufacturing systems in which flexibility features are relevant. The specific goal is the comparison between two system architectures. The first system is designed according to the focused flexibility paradigm while the second deals with the classical idea of flexible manufacturing systems. Since in the evaluation of flexible manufacturing systems, the impact of rules and methods at the operational level is remarkable, it will be necessary to include in the evaluation tool all the rules designed to manage both the part and tool flows in the system. Moreover, in order to realize in an efficient way the validation phase, illustrated in the following chapter, the proposed tool has a library of management rules. The tool may be configured to evaluate different scenarios and alternatives in an automatic way. The automatic integration of different management rules according to the constraints and to the characteristics of the system have been preliminary solved. In order to realize an efficient tool for the requirements of the validation phase, discrete event simulation has been selected among the applicable methods. Discrete event simulation allows to analyze a production system and to assess the relative performance, even if the preliminary activity related with the representation of the system model is a remarkable task. Indeed, the accuracy of the results obtainable from the simulation tool depends on the soundness of the model adopted to represent the system.

222


Various techniques and languages are available to describe systems through formal representation. Moreover, several software packages may be exploited to write simulation software on the basis of system formal representation. In Anglani et al. (2002) an approach to integrate the formal representation phase and the development of a simulation model is presented. The proposed methodology is based on the UML standard and on the simulation language Arena. The authors exploit the UML capabilities to represent the significant components and relationships of a flexible manufacturing systems even if the proposed model is a simplified representation of the actual FMS complexity. Therefore, considering the advantages given by the use of UML standard language, the formal models of FFMS and FMS architectures reported in this book have been formalized UML language. In particular, the first step in order to realize the proposed tool is to represent the system at the desired level of detail. Second, the simulation model has to be developed. Third, the validation and verification phases have to be carried out as usually done for a generic software package. A characterization of the system to be reproduced is reported in the following sub-sections.

9.2.1 Simulation Model Formalization The description of the simulation model has the objective of illustrating each component at the desired level of detail with a high level of generality and intelligibility. In order to accomplish this goal, it is necessary to select a formal language to describe the model with the required features. As previously reported, the language exploited in the following is the Unified/Universal Modeling Language (UML). This language consists of a set of object-oriented modeling notations that have been standardized by the OMG object management group in order to represent every kind of system. It defines a meta-model based on a graphical notation that can be used as a support for formal modeling. The UML uses graphical notations to illustrate all the system specifications. Since specifications are usually complex, there are several diagrams, refereed as UML diagrams, available to provide different views of the analyzed system. UML diagrams represent three different views of a system model: the functional requirements view, the static structural view and the dynamic behavior one. The representation of the components and relationship of the system under study is reported in the following. The UML use-case and activity diagrams will be the basis of the simulation model. The following section provides a deeper insight into the single system components and synthetic comments to the diagrams. The most relevant UML use cases are reported in Fig. 9.1, Tables 9.1 and 9.2.


223

Fig. 9.1 Use case of the main activities of the simulation model

A complete UML representation is not reproducible in this chapter because of the complexity of the system. For this reason, a global illustration has been provided with the aim of referring to the most significant UML modules. Anyway, the proposed representation refers to the model of an automated production system dedicated to machining operations of the Table 9.1 Actors of the main activities of the simulation model Actor Description Pallet Part Part carrier LU station Machine Tool Tool Carrier

A hardware interface between the load/unload station and the machines which allows that parts are processed in the system. A raw or partially machined part to be processed. A transport system dedicated to move pallets among the machining centers and the load unload stations. A LU station dedicated to load/unload parts from and to the pallet. A machining center (general purpose or dedicated) on which pallets are processed. A tool used in machining operations. A carrier dedicated to transport tools among the tool magazines of machining centers and the system central tool magazine.

224


Table 9.2 Description of the activities of the simulation model Activity Description Pallet loading and unloading Machining Pallet transport Tool transport

Parts are loaded and unloaded on/from a pallet by the LU station unit. A pallet loaded with raw or partially machined parts is processed by a machining center with a proper set of tools. A pallet is moved from a machine to another machine or to a LU station (and vice versa). A tool is moved from a machine to another machine or to the Tool Room (and vice versa).

parts. Such a model is characterized by a set of flexibility features related with the management of the machining operations. These features have been designed in order to evaluate the performance of both FFMS and FMS architectures. A first flexibility characteristic regards the possibility to process the parts on one or more machines. This means that each part may require one or more setup to be completely machined. As anticipated in Chap. 7, parts are mounted on pallets by means of fixtures. It is possible to associate more than one pallet to each part in each different setup. Each pallet may be loaded with one or more parts in different setup positions. Moreover, pallets are moved among the Load/Unload (LU) station and the machining centers by an automatic part transport system. On each machining center, the pallet processing is executed with a proper set of tools. Tools can be shared among the machining centers. Once a pallet is completely machined, it returns to the Load/Unload (LU) station in order to unload, partially or completely, processed parts and to load raw parts. In the developed simulation model it is assumed that machining centers and the Load/Unload stations are laid out over a line and that the Load/Unload stations are centrally located with respect to the machining centers. The activity diagram related to the transition of the pallet from the LU station to a machining center is shown in Fig. 9.2, Tables 9.3 and 9.4. The processing of a pallet on a machining center is represented on the related activity diagram reported in Fig. 9.3, Tables 9.5 and 9.6. The unloading of the pallet is represented by the activity diagram reported in Fig. 9.4, Tables 9.7 and 9.8.

9.2.2 Implementation of the Simulation Model Since several different configurations, for each system architecture, have to be simulated, a key-point is the implementation of an evaluation environment able to be automatically configured both from the physical and from the logical


225

Fig. 9.2 Activity diagram of the ‘‘pallet loading’’ activity of the simulation model

Table 9.3 Sub-activities related to the ‘‘pallet loading’’ activity Sub-activity Description Load parts on the pallet Transport pallet to buffer Transport pallet to machine Wait for a machine to process the pallet

All the parts required by each pallet are loaded at the LU station. Moves a pallet waiting for a machining center to a buffer. A pallet is transferred to a machining center in order to start the processing phase. Each pallet waits for a free machining center in order to start the necessary processing.

Table 9.4 Decisions related to the ‘‘pallet loading’’ activity Decision Description No machine available Machine available

The pallet does not find an available machining center for being processed. Since an idle and admissible machining center is available in the system, the pallet is transferred to the machining center to be processed.

226


Fig. 9.3 Activity diagram for the ‘‘pallet machining’’ activity of the simulation model

point of views. The developed simulation model allows to simulate automatically different scenarios on the same configuration and to switch between different simulation campaign automatically. The configuration of the simulation model is enabled by varying a specific set of model parameters. It is important to notice that even the management policies can be modified by varying the proper set of parameters. The generality of the simulation model allows users to reproduce a Focused Flexibility Manufacturing System in addition to a general Flexible Manufacturing System. The FFMSs/FMSs system configurations that might be simulated are a combination of the following resources and parameters. In particular, it is important to note that the simulation model may be configured both in the number of the resources available in the system (e.g. the total number of machining centers) and in the functional parameters of system resources. The complete list is reported in the following:


227

Table 9.5 Sub-activities related to the ‘‘pallet machining’’ activity Sub-activity Description Place pallet on machine waiting position Move pallet to working position Prepare for the tool of the next operation Request tool for the pallet processing

Send tool for the pallet processing Perform the next operation on the pallet Move pallet to the exit mode Transport pallet to machine

Transport pallet to LU station Transport pallet to buffer Wait for a machine to process the pallet

A pallet enters into the machining center and occupies the waiting position of the machining center. A pallet occupies the working position of the machining center. The supervisor of the machining center searches the tool for the next operation. The next tool is requested by the tool management system. If the tool is not present into the machining center magazine, the tool management system requests the tool from the central magazine or from another machining center. Once the necessary tool arrives at the machining center, the tool is loaded in the local tool magazine. If the necessary tool is present, the next operation is performed by taking into account both the cutting time and the total time of the operation. A pallet is moved from the processing position of the machining center to the waiting position. If the part program of a pallet cannot be completed on the current machining center, the pallet is moved to another machining center; different classes of machining centers may be considered. If a pallet part program is completely executed, an unloading operation is necessary. A pallet is moved to a buffer to wait for an available machining center. At the buffer, a pallet waits for a machine in order to be free to start the necessary processing.

Table 9.6 Decisions related to the ‘‘pallet machining’’ activity Decision Description Pallet processing on the current machine is completed Pallet processing on the current machine is not completed Pallet part program is completed

Pallet part program is not completed

No machine available Machine available

A pallet has completed the set of operations that may be performed on the current machining center. A pallet requires other operations on the current machining center (which in turn requires different tools). A pallet has completed the set of the operation to be performed (all the part program), therefore an unloading operation must be performed. A pallet requires other machining operations to be performed on a different machining center or machining centers; it requests to be moved to another machining center. A pallet which does not find an available machine in order to be processed is moved to the buffer. The pallet is transferred to the available machine.

228


Fig. 9.4 Activity diagram related to the ‘‘pallet unloading’’ activity of the simulation model

Table 9.7 Sub-activities related to the ‘‘pallet unloading’’ activity Sub-activity Description Unload parts from pallet Transport pallet to buffer Transport pallet to LU station Wait for parts to load the pallet

All the parts loaded on a pallet are unloaded at the LU station and are available for other operations if necessary. The pallet is moved to a buffer to wait for parts to be loaded. A pallet is transferred to the LU station in order to be loaded with new available parts. At the buffer, the pallet waits for parts to be loaded.

Table 9.8 Decisions for the ‘‘pallet unloading’’ activity Decision Description No parts available for loading Parts available for loading

Since no parts can be loaded on the pallet, the loading operation is not executed. Since parts to be loaded on the pallet are available, the pallet can be loaded.


229

up to N_max machining centers over a line layout, with N_max = 8; a loading / unloading station centrally positioned in the line layout; a transport system to handle pallets into the system, consisting of one or two

shuttles able to transport a single pallet and equipped with an automated exchange system; up to P_max pallets buffer places distributed along the line layout, with P_max = 50; a central tool magazine distributed along the line layout; a tool room for tool regeneration; a tool transport system. The tool transport system moves on a straight track; it connects the central tool magazine with the tool magazine of each machining center; each machine is equipped with a tool magazine provided by a tool exchange system and a pallet exchange system between the workstation and the pallet transportation system.

On the basis of the assumptions previously reported, an example of system layout is reported in Fig. 9.5. Moreover, each system resource requires the definition of a list of parameters, as explained in the following. The machining centers are placed in line along the path of the carrier according to an assigned distance and are characterized by the following parameters: machine type, shuttle rotation time, size of the tool machine magazine and time for tool change. For each part type, it is necessary to define the following parameters: the part type code, the number of parts to be produced, and the code of the first pallet type occupied by the parts. Indeed, any part may be associated with only one pallet type, if only one setup is required to completely machine the considered parts. Otherwise, the part type may be associated with a set of different pallet types when more than one setup is needed. In such a case, the sequence of pallets associated with each part type and to each part setup has to be defined.

Fig. 9.5 System layout of the simulation model

230


The part program is defined by specifying the part type related, the list of machining operations, the tool type per operation, the cutting time, the rapid time and the association of the operation to the machine type. With regard to the part carrier, it is possible to set the following parameters: the average speed, the time required to load and unload the pallets to and from the carrier and the management policy to manage the transportation requests. The tool carrier is characterized by the following parameters: average speed and loading and unloading time. The simulation model can manage different tool types. For each tool type the following parameters have to be defined: the tool type code, the number of copies per tool type, the regeneration time and the tool life. Once all the system resources with the corresponding set of parameters have been defined, it is necessary to complete the assumption for the simulation model by defining the part and tool management policies that must be considered in each specific simulation experiment. The various options for the two management policies are described in the following.

9.2.2.1 Pallet Management Policy Parts move along the system by means of the pallet transport system. In the case of multiple requests for the pallet carrier, different management policies can be adopted:

Policy 1. First In First Out (FIFO) rule. Requests are ordered on the basis of the instant they are issued.

Policy 2. For each pallet i, a priority index is calculated on the basis of the quantity: ai ¼ ProcessedPalletsi =PalletsToBeProcessedi

(9:1)

where i is related to the percentage of part type machined. The lower is the value of i, the higher is the priority of the corresponding pallet i. Policy 3. For each pallet i, a priority index is calculated on the basis of the quantity: bi ¼ ProcessedPalletsi =ðoi PalletsToBeProcessedi Þ

(9:2)

oi ¼ PalletProcessingTimei =maxðPalletProcessingTimei Þ

(9:3)

where

The last policy is similar to the second policy but the time to process the remaining pallets is considered with the weight !i. The higher is the processing time of a pallet i, the lower is the parameter i, the higher is the priority for the pallet i. Once the carrier is loaded, the transport mission is executed and the pallet is carried to the first idle machining center; if this is not possible it is the pallet is loaded on the first machine with a free waiting position or in the worst case it


231

will be stored in the pallet buffer. A pallet management module coordinates the transport system in order to satisfy as soon as possible to transport requests. If the number of tool carrier in the simulation experiment is equal to one, the main goal of the pallet management module is to avoid idle time of the machining centers for lack of pallets. This main goal is satisfied taking into account also the possibility to minimize the total length of the paths necessary to the pallet transport system to execute the requested missions. Otherwise, if the total number of part transport systems is greater than one, the describe part management problem is augmented in the complexity for the necessity to manage also the route of the transport systems in order to avoid deadlock situations.

9.2.2.2 Tool Management Policy The tool management policy implemented in the simulation model, see Toma et al. (1995), allows the machining centers to share each different tool copy available in the system. When a pallet reaches the machining center waiting position, the tools which executes such a set of operations, as defined in the part program, are requested. As soon as a tool completes the processing on a machining center, it is available for other machining operation even on other machining centers. Indeed, if a machining center needs a tool that is not present in its local magazine, firstly, a request to the central magazine is generated. If a copy of the requested tool type is not available, a request is generated towards the tool magazines of the machining centers. Tool requests are ordered on the basis of FIFO rules. As soon as a machining center releases a tool copy, the first tool request is selected. If a tool copy matching the tool request is available, a tool mission is scheduled to move the tool to the machining center. Otherwise, the availability of tools belonging to the tool requests list is checked tool by tool until the list is empty. The list of scheduled tool transport missions is re-defined each time a tool copy is released by a machining center in order to limit idle time on the machining centers due to tool unavailability. When the tool life ends, the tool copy is transferred to the tool room for the regeneration process and it is not available for booking.

9.2.3 Focused Flexibility Aspects in the Simulation Model Focused Flexibility Manufacturing System configurations can be simulated by the described simulation model by properly setting the corresponding parameters. In order to extract such information, the simulation model has to access to the data contained in the main database tables described in Chap. 4. In this section, the relationships between the simulation model data and the main database tables will be described.

232


9.2.3.1 Model Data Definition The main parameters of a simulation run (length, warm-up, number of replications) are inferred from a specific table of the database named ‘‘simulation’’ (Table 4.27). Information about Machines, LU station, Tools and Carriers are extracted considering the concepts of Tables 4.8, 4.9, 4.10 and 4.11 together with their relations reported in Table 4.22. In the simulation model, potentially each part program may be executed on different machining centers. Consequently, a pallet can perform the first set of operations on a specific machining center, and then move to a different machine type to execute other processing operations. In order to collect the necessary information, in the simulation model, the part program is defined according to the concepts of ‘‘Workingstep’’ (Table 4.16) and ‘‘Workplan’’ (Table 4.17). In this way the part program associated with the ‘‘pallet’’ is completely determined. The remaining parameters associated with the ‘‘Pallet’’ concept are extracted from the information connected to Workpiece and Scenario (Table 4.1, 4.3, 4.17, 4.18, 4.21 and 4.23).

9.2.3.2 FFMS Model Management Aspects Since the constraint to perform all the operations related to each setup on a single machining center may be relaxed in FFMS architectures, several machining centers may be involved in the processing of a single pallet for each setup. For this reason, a greater number of transportation requests may be issued by each pallet during the part program processing than in the FMS case. Indeed, in the FFMSs architecture in addition to the transportation missions among the LU station, the machining centers and the pallet buffer positions, it is possible to move a pallet among many machining centers. This could lead to select more than one pallet carrier for the transport system. Therefore, the evaluation of the performance of production systems characterized by more than one pallet carrier becomes critical. In the proposed simulation model, it is foreseen the possibility of simulating the FFMS configuration with two pallet carrier units sharing the same railway. However, in FFMSs the need to move pallets directly among different machining centers could lead to collision problems when two carriers are present. For this reasons, a pallet management system dedicated to the FFMS architecture has been designed and implemented in the simulation model. Also in the FMS architecture it is possible to design two transport units. However, this type of configuration is usually adopted splitting the transport path in two separate and independent zones (e.g. the left and the right side respect to the LU station). This configuration may be considered collision-free. Anyway, the pallet management system determines the sequence of pallet missions and schedule the activities of the transport systems. In the simulation model an attribute ‘‘release time’’ is related to each transport mission. It


233

represents the time in which the pallet requires the transport mission. The transport mission is labeled ‘‘critical’’ if the mission scheduling leads starvation or blocking for one resource (machining centers or LU stations). The critical time for a mission represents the maximum time within the relative transport mission need to be satisfied in order to minimize the resources idle or lack of pallets. The policy to select the next mission to be executed by the carriers, among the set of equivalent missions, may consider:

balancing the machine/LU station resource utilization, optimizing the performance of the transport system. The first aspect takes into account the resource state in order to select the next pallet to be moved. A policy can select the next mission depending on the release time or the critical time. The second aspect considers the departure and arrival stations of a mission in order to optimize the carrier path. Various alternatives are implemented in the simulation model. The ‘‘most critical mission’’ policy selects the mission in order to balance the machines/LU station saturation. The ‘‘transport system optimization’’ policy selects the mission in order to optimize the transport system performance. Moreover, a hybrid approach has been implemented. Taking into account the time windows of each transport missions and the performance of the transport systems, it is possible to selects a set of equivalent missions respect to the goal to minimize resources idle time. The hybrid policy considers the equivalent set and selects the next mission in order to optimize the transport system (N is a policy parameter). In this way, even if the optimization of the transport system is restricted to a limited number of missions (the most critical ones), it is possible to introduce optimization policy of the pallet transport system. In the simulation model, if two carriers are considered, each time a carrier has to start the execution of a mission, a deadlock has to be avoided with the second part carrier. For such a reason, the transport path can be modified in order to avoid deadlocks and a carrier can be forced to wait the end of another transport mission. The order and the paths by which the missions of the two part carrier are executed depends on the mission attributes. The pallet carrier unit movements may be in conflict when a carrier is on the other carrier path. Deadlock may occur if carriers move along the same railway segment in different directions. A specific logic has been implemented to avoid deadlocks. The proposed solutions are reported in the following. On the one hand, it is foreseen that a carrier seizes the entire railway portion before the execution of the related transport mission. On the other, a carrier has to be moved away from the path that has to be seized by the other carrier; in such a case a carrier is moved along a different and longer path than the shortest one. The described features related with the FFMS architecture implemented in the simulation model has been validated through a set of simulation experiment described in the following paragraph.

234


9.3 The Simulation Model Validation The simulation model testing usually is a long task due to the necessity to take into consideration both the verification and validation phases. This section aims at evaluating the behavior of FFMS solutions in output from the FFMS design approach. A specific case study has been defined in order to execute the validation of the simulation model. This phase aims at validating the following characteristics:

ability of simulating different cases in which bottlenecks may be identified either in the general purpose machining centers or in the dedicated ones;

ability of simulating a two part carrier system case; the part carriers must be able to share the same railway. The proposed case study may be summarized as follows. The FFMS configuration is composed of four CNC machining centers: the first three machining centers are general purpose while the other one is a dedicated machining center. The dedicated center is the closest to the LU station, which is centrally located within the in-line layout. The machine tool change time is 2.5 s. The shuttle rotation time is 6 s. No machine failures are supposed to occur. The pallet transport system may be configured up to two part carriers; its main features are: linear speed 45 m/min and pallet load time 15 s. For the validation phase the hypothesis is made that only one lot has to be produced. Each part has to be completely processed on the same pallet if both the general purpose and the dedicated machining center are used. Each pallet is loaded with four parts. At the LU station, four working units are available for the load and unload operations. The load/unload time is 10 min for pallet. The total number of operations to completely machine the considered part is 15. For each operation, the cutting time comes from a uniform distribution with min/max values equal to 0.8 min and 1.6 min; once inferred, such numerical values are used for all the experimental campaign. For each operation, the total time is 20% longer than cutting time. The part program is supposed to be divided into three general parts: GP1, DED and GP2. The first group of operations, refereed as GP1 in the following, is constrained to be executed on a general purpose machining working center. The second group, DED, represents the central portion of the part program that is constrained to be processed on the dedicated machining resource. Finally, the last group, GP2, is executed on a general purpose machine. In general terms, the production cycle is: GP1/DED/GP2. For example, if the cardinality of the total number of operations in the group DED is equal to one, the operations from 1 to 6 and from 8 to 15 are executed by just one of the general purpose machine; whereas the operation 7 is executed by the dedicated machine. The total number of tool types is 15. For each tool type, 4 copies are available. Since the simulation experiment is deterministic, only one replication


235

is performed. The warm-up period length is 600 min, whereas the replication length is 7200 min.

9.3.1 Numerical Results In order to evaluate the behavior of the FFMS solution in comparison to the FMS architectures, the validation phase has been carried out focusing the analysis on the following factors:

D: number of operations of the part program that are executed on the

dedicated machine (DED) with respect to the total number of operations in the part program. In particular, this value is varied from 1 to 7. R: part program reduction factor. The part program length is investigated by reducing the initial duration of the operations. For each operation, both the cutting time and the total time are reduced by the factors: 1 and 10; C: number of pallet carriers, in the value set {1, 2}. The system performance is evaluated in terms of: average general purpose machines utilization, referred as ‘‘Av GP Mc Util’’ in the following table, average dedicated machine utilization, refereed as ‘‘Av Ded Mc Util’’ in the following table, average transport system utilization, considering the overall carrier system and referees as ‘‘Av Transport system Util’’ in the following table, average pallet throughput, refereed as ‘‘Av Throughput’’ in the following table and measured in pallets per hour unloaded from the system, average mission rate, refereed as ‘‘Av MissionsRate’’ in the following table and measured in missions per hour.

The obtained results are reported in Table 9.9. The first set of experiments (A1–A4) aims at demonstrating the possibility of splitting the execution of the part program on different machining centers and evaluating the different bottlenecks in the systems (parameter D is varied). In the simulation R/D/C = 1/1/1 the utilization of the general purpose machining centers is equal to 1 whereas the dedicated machining working center utilization is equal to 0.27. On the contrary, in the simulation R/D/C = 1/7/1 the utilization of the general purpose machining centers is equal to 0.62 while the dedicated machining working center utilization is equal to 100%. If the D value is set to 3 or 5, the machine workload is almost balanced. Indeed, three general purpose machining centers deals with (15–D) operations, whereas the general purpose machining center performs the remaining D processing operations. Therefore, the optimal D value may be inferred from the equation 3/1 = (15-D)/D, that is D = 3.75. Consequently, the best throughput among the simulated tests is obtained for D = 3 (R/D/C = 1/3/1). The simulation test cases with R = 1 and

236


Table 9.9 Numerical case study results for the analysis of the FFMS performance Exp R D C Av GP Av Ded Av Av Av Mc Util Mc Util Transport Throughput MissionsRate system Util [pallets/h] [missions/h] A1 A2 A3 A4 B1 B2 B3 B4 C1 C2 C3 C4 D1 D2 D3 D4

1 1 1 1 1 1 1 1 10 10 10 10 10 10 10 10

1 3 5 7 1 3 5 7 1 3 5 7 1 3 5 7

1 1 1 1 2 2 2 2 1 1 1 1 2 2 2 2

1.00 1.00 1.00 0.62 1.00 1.00 1.00 0.62 1.00 1.00 1.00 0.61 1.00 1.00 1.00 0.62

0.27 1.00 1.00 1.00 0.27 1.00 1.00 1.00 0.26 1.00 1.00 1.00 0.27 1.00 1.00 1.00

0.10 0.12 0.10 0.07 0.05 0.06 0.05 0.03 1.00 1.00 1.00 1.00 0.89 1.00 0.78 0.46

0.89 1.03 0.83 0.60 0.89 1.03 0.83 0.60 8.27 8.68 7.74 5.91 8.92 10.07 8.23 5.95

3.57 4.10 3.31 2.38 3.57 4.10 3.31 2.38 33.09 34.72 30.94 23.65 36.74 41.02 33.50 24.21

C = 1 confirm the validity of the proposed model, reproducing the same results in terms of bottleneck shift between the general and the dedicated machining centers. The second set of experiments (B1–B4) aims at proving the possibility to simulate different configurations increasing the total number of part carriers (parameter C is varied to 2). The increasing of the number of part carriers from 1 to 2 is not justified from a performance standpoint. The overall transport system utilization decreases by a factor of 2 because of the second carrier. Taking into consideration the total number of carrier missions per hour with two part carriers, the total number of missions is equal to the previous one. The same result is obtained for the pallet throughput and machine utilization. Briefly, the second carrier is not necessary in case R = 1. The third set of experiments (C1–C4) considers the decrease of the part program length by a factor of 10 and the exploitation of only one part carrier (R = 10 and C = 1). In this way, the transportation request rate increases significantly. The utilization of machines is equivalent to the R = 1 case. However, the transport system represents the system bottleneck. Indeed, the pallet throughput is not decupled respect to the R = 1 case, in particular in the simulation experiment with R/D/C = 1/3/1. In the last set of experiments (D1–D4) a second carrier is added and the system performance increases. The second carrier allows in order to significantly improve the pallet throughput when D = 3 is considered. Indeed, since the machining centers workload is balanced, the second carrier allows exploiting the machine set. In this case, production rate increases of 16% (from 8.68 to 10.07 pallet/h). On the contrary, if R/D/C = 10/7/1 and R/D/C = 10/7/2 are


237

considered, the second carrier is not exploited (from 5.91 to 5.95 pallet/h) because the main bottleneck is represented by the dedicated machine. Finally, it is possible to argue that the number of the allocated carriers is important when the number of transportation requests increases. Indeed, if there is not a part program reduction, each pallet remains on machines for a long period and the second carrier unit is not necessary. Indeed, when the part program length decreases, the second carrier unit allows increasing the overall number of transport missions. Since the carrier units share the same path, the presence of the second unit leads to increase the number of collisions between transport requests. For such a reason, it is important exploiting the second carrier unit only when the transportation request rate is significant.

9.4 Conclusions In this chapter a simulation model capable of evaluating various FFMS configurations has been presented. In particular, the modeling phase has been reported focusing on the key characteristics of the considered systems. The simulation model has been validated in order to demonstrate the influence of the flexibility issues on system performance. Moreover different cases exist in which such production architecture is suitable to be adopted. Further development could regard a deep investigation of the relationship between flexibility and performance. Some analyses have been presented in the last chapter of this book referring to a real production case in order to establish the potential of FFMS architecture in the foreseeable future.

References Anglani A, Grieco A, Pacella M, Tolio T (2002) Object-oriented modeling and simulation of flexible manufacturing systems: a rule-based procedure. Simul Model Prac Theory 10:209–234 Averill M Law A and, W David Kelton (2000) Simulation modeling and analysis – third edition. McGraw-Hill, New York Banks J, Carson J, Nelson B, Nicol D (2005) Discrete-event system simulation – fourth edition. Pearson, New York Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceedings of the 4th Int Conf on Digit Enterp Technol, Bath, UK, 19–21 September, pp 627–636 Creighton D, Nahavandi S (2003) Application of discrete event simulation for robust system design of a melt facility. Robot Comput-Integr Manuf 19(6):469–477 Gien D, Jacqmart S (2005) Design and simulation of manufacturing systems facing imperfectly defined information. Simul Model Prac Theory 13(6):465–485 Greasley A (2008) Using simulation for facility design: a case study. Simul Model Prac Theory 16(6):670–677 Grieco A, Nucci F, Anglani A (2003) Representation of fuzzy time variables in discrete event simulation. Integr Comput-Aided Eng 10(4):305–318, IOL Press

238


Lu M, Wong L (2007) Comparison of two simulation methodologies in modeling construction systems: manufacturing-oriented PROMODEL vs. construction-oriented SDESA. Automat Construct 16(1):86–95 McHaney RW (1991) Computer simulation: a practical perspective. Academic Press, New York Park SC (2005) A methodology for creating a virtual model for a flexible manufacturing system. Comput Industry 56(7):734–746 Pidd M (1998) Computer simulation in management science – fourth edition. Wiley, New York Robinson S (2004) Simulation – the practice of model development and use. Wiley, New York Ryan J, Heavey C (2006) Process modeling for simulation. Comput Industry 57(5):437–450 Siemiatkowski M, Przybylski W (2006) Simulation studies of process flow with in-line part inspection in machining cells. J Materials Processing Technol 171(1):27–34 Sivakumar AI, Chong CS (2001) A simulation based analysis of cycle time distribution, and throughput in semiconductor backend manufacturing. Comput Industry 45(1):59–78 Tolio T, Grieco A, Semeraro Q (2001) A review of different approaches to the FMS loading problem. Int J Flex Manuf Syst 13(4):361–384 Toma S, Tolio T, Semeraro Q, Grieco A (1995) Simulation of tool and part flow in FMSs. Int J Prod Res 33:643–658 Wohlgemuth V, Page B, Kreutzer W (2006) Combining discrete event simulation and material flow analysis in a component-based approach to industrial environmental protection. Environ Model Software 21(11):1607–1617 Zeigler BP, Praehofer H, Gon Kim T (2000) Theory of modeling and simulation: Integrating discrete event and continuous complex dynamic systems – second edition. Academic Press, New York

Chapter 10

Testing Manfredi Bruccoleri, Carlo Capello, Antonio Costa, Francesco Nucci, Walter Terkaj and Anna Valente

Abstract This chapter aims at presenting the experimental analyses carried out to evaluate the benefits coming from applying the manufacturing system design framework presented in the previous chapters. To this purpose three families of products belonging to different production contexts have been studied. These products have been used as input data of the testing experiments which were aimed at studying the performance of an FFMS when facing production problems characterized by technological and demand evolution. The testing experiments have been carried out by exploiting the software tools that have been developed by implementing the methodologies presented in the previous chapters. Keywords FFMS design framework testing Design of Experiment Value of the Stochastic Solution System Performance Evaluation

10.1 Introduction In the previous chapters of this book, the main phases of an FFMS design approach have been described to provide a structured guidance to determine the system characteristics which better fit the production requirements. Despite each single chapter investigates a specific aspect of the system design process, the analysis of production problems represents a common feature of strategic importance. Indeed, the ability to customize the production system characteristics on the input requirements determine economic advantages as well as system solutions that can better cope with future changes of the demand (Cantamessa et al. 2007). These advantages regard both machine tool builders and system users. On the one hand, the strategy of customizing the system flexibility on the production W. Terkaj (*) Dipartimento di Meccanica, Politecnico di Milano, Milano, Italy e-mail: [email protected]


239

240


requirements provides benefits to the machine tool builders because the reduction of manufacturing system costs can be exploited to enhance the profit margin and/or to increase the competitiveness in the market by offering cheaper solutions (see Chap. 1). On the other hand, the system user is particularly interested in purchasing an affordable system designed considering both the present and the forecasted production problems. The industrial interest on the topic of focused flexibility has been addressed in Chap. 2 by means of an empirical investigation. Moreover, some industrial efforts in the direction of customizing system solutions on the customer needs have been presented in Chap. 3. Anyway, in practice most of the designed system can still be classified in the family of traditional systems despite these architectures do not represent an optimal solution. This is partly due to the absence of approaches to support machine tool builders when facing the main steps of the manufacturing system design. The aim of this chapter is to show that there is a set of production problems which would require customized system solutions. The first part of this chapter presents an analysis of three different families of products which have been used to test the FFMS design approach. The second part of the chapter will be dedicated to show the most relevant results obtained from the testing experiments. In particular, the experiments aim at addressing the robustness of system solutions with respect to the variability of the production problems. Moreover, the benefits coming from using the stochastic programming technique for designing the system have been evaluated. Finally, the viability of the designed system solutions is analyzed through simulation. The testing experiments carried out in this chapter complete the analyses already presented in Chap. 7 where the impact of the production problem characteristics (i.e. the part family, the part mix and the aggregate demand) and of the database of selectable resources (i.e. cost and performance of the dedicated machines) on the performance of Focused Flexibility Manufacturing Systems has been investigated. This chapter is structured as follows. Section 10.2 analyzes the families of products while Sect. 10.3 describes how the test cases have been generated. Then, Sects. 10.4, 10.5 and 10.6 present the results of the testing experiments.

10.2 Description of the Product Families In this section three different families of products will be presented. These families are composed of:

products for automotive applications; products for railway applications; products used in the field of flow control systems.

10

Testing

241

(a)

(b)

(c)

Fig. 10.1 (a) Product code 240 (b) Product code 260 (c) Product code 270

In particular, the first and third families are composed of products of mid technological complexity, whereas the second one includes complex part types. All the analyzed products can be processed on horizontal machining centers since they are characterized by prismatic features. However, this does not strictly mean that the geometry of the products is prismatic: for instance, the last family of products produced for hydraulic applications is composed of axial-symmetric part types. Information related to the described families of products have been formalized using the framework presented in Chap. 4.

10.2.1 Automotive Components The products composing this first family are automotive components of a hydraulic primary chain tensioner, i.e. a hydraulic actuator which constantly keeps the chain in tension. The part family is composed of seven workpiece types (product codes 240, 260, 270, 280, 380, 500 and 900). For each part type a 3D drawing is shown in the Figs. 10.1, 10.2 and 10.3.

(a) Fig. 10.2 (a) Product code 280 (b) Product code 380

(b)

242


(a)

(b)

Fig. 10.3 (a) Product code 500 (b) Product code 900

The material and the bounding geometry (i.e. a parallelepiped) of each workpiece type is reported in Table 10.1. Information is formalized following the definition of Workpiece type introduced in Chap. 4 (see Sect. 4.3.1 and Table 4.1). In particular, all the analyzed products are in aluminum alloy and the dimensions of the products is measured referring to a coordinate system with the origin placed in the center of each bounding geometry. Once the information concerning the part family has been collected, each workpiece type has been analyzed from a technological point of view. In particular, the working directions have been defined as represented in Figs. 10.4, 10.5 and 10.6. Data regarding the description of the machining features and the machining operations are reported in the following tables. As an example, the machining features of the product code 280 are illustrated in Fig. 10.7. Tables 10.2, 10.3, 10.4, 10.5, 10.6, 10.7, 10.8 and 10.9 report the data concerning the machining features following the definitions provided in Table 4.2 of Chap. 4. Each table includes data related to the position of the machining feature (coordinates x, y and z) and the working directions expressed as direction cosines (cos_x, cos_y, cos_z). Table 10.1 Characteristics and dimensions of the workpiece types id_workpiece its_material x_pos x_neg y_pos y_neg

z_pos

240 Aluminum alloy 33.95 33.95 18.23 18.23 27.16 268 Aluminum alloy 22.45 22.45 36.9 36.9 24.75 270 Aluminum alloy 32.98 33 33.75 33.75 13 280 Aluminum alloy 28.7 28.7 30.95 30.95 11.4 380 Aluminum alloy 41.59 41.59 55.42 55.42 57.13 525 Aluminum alloy 64.48 64.48 37.8 37.8 59.3 916 Aluminum alloy 64.56 64.56 45.2 45.2 83.81 x_pos = x_bounding_pos; x_neg = x_bounding_neg; y_pos = y_bounding_pos; y_bounding_neg; z_pos = z_bounding_pos; z_neg = z_bounding_neg

z_neg 27.16 24.75 13 11.4 57.13 59.3 83.81 y_neg =

10

Testing

243

(a)

(b)

(c)

Fig. 10.4 Working directions (a) Product code 240 (b) Product code 260 (c) Product code 270

Fig. 10.5 Working directions (a) Product code 280 (b) Product code 380

(a)

(a)

(b)

(b)

Fig. 10.6 Working directions (a) Product code 500 (b) Product code 900

(a)

(b)

(c)

Fig. 10.7 Representation of the machining features of product code 280

244


Table 10.2 Machining features of product code 240 id_feature Abstract x y z cos_x supertype [mm] [mm] [mm]

cos_y

cos_z

Working direction

240_1A planar_face 26.8 7.1 22.1 0.000 0.000 1.000 D1 240_1B planar_face 26.8 3.8 22.1 0.000 0.000 1.000 D1 240_2a round_hole 5.9 1.2 12.2 0.000 0.000 1.000 D2 240_2b round_hole 5.9 1.2 12.2 0.000 0.000 1.000 D2 240_2c round_hole 5.9 1.2 12.2 0.000 0.000 1.000 D2 240_2d round_hole 5.9 1.2 15.8 0.000 0.000 1.000 D2 240_5a round_hole 16.7 1.2 9.3 0.842 0.000 0.539 D3 240_5b round_hole 16.7 1.2 9.3 0.842 0.000 0.539 D3 240_6 round_hole 15.7 1.2 20.9 0.537 0.000 0.843 D4 240_7 round_hole 8.0 12.6 18.1 0.612 0.791 0.000 D5 240_8A round_hole 26.8 7.1 22.1 0.000 0.000 1.000 D1 240_8B round_hole 26.8 3.8 22.1 0.000 0.000 1.000 D1 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction

Table 10.3 Machining features of product code 260 id_feature Abstract supertype x y z [mm] [mm] [mm]

cos_x

cos_y cos_z

Working direction

260_1 planar_face 16.4 0.0 24.8 0.000 0.000 1.000 D1 260_10b round_hole 0.6 0.0 17.8 0.000 0.000 1.000 D1 260_10c round_hole 0.6 0.0 17.8 0.000 0.000 1.000 D1 260_11 compound_feature 11.9 8.8 18.3 1.000 0.000 0.000 D2 260_2a round_hole 0.6 0.0 12.8 0.000 0.000 1.000 D1 260_2b round_hole 0.6 0.0 12.8 0.000 0.000 1.000 D1 260_2c round_hole 0.6 0.0 17.8 0.000 0.000 1.000 D1 260_2d round_hole 0.6 0.0 22.6 0.000 0.000 1.000 D1 260_2e round_hole 0.6 0.0 12.8 0.000 0.000 1.000 D1 260_7a round_hole 16.9 14.2 20.8 0.777 0.630 0.000 D3 260_7b round_hole 16.9 14.2 20.8 0.777 0.630 0.000 D3 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction

Table 10.4 Machining features of product code 270 id_feature Abstract x y z supertype [mm] [mm] [mm] 270_1 270_15 270_2c 270_2d 270_3b 270_4 270_a

planar_face round_hole round_hole round_hole replicate_feature (round_hole) round_hole round_hole

0.0 28.0 24.5 23.5 7.6 21.5 24.5

cos_x

cos_y

cos_z

Working direction

0.000 0.000 1.000 1.000 0.000

0.000 0.000 0.000 0.000 0.000

1.000 1.000 0.000 0.000 1.000

D1 D1 D2 D2 D1

7.0 0.000 3.0 1.000

0.000 0.000

1.000 D1 0.000 D2

0.0 13.0 9.0 7.0 9.0 3.0 9.0 3.0 14.6 13.0 16.0 9.0

10

Testing

Table 10.4 (continued) id_feature Abstract supertype

245

x [mm]

y [mm]

z [mm]

cos_x

cos_y

cos_z

Working direction

270_b round_hole 24.5 9.0 3.0 1.000 0.000 0.000 D2 270_e planar_face 24.5 9.0 3.0 1.000 0.000 0.000 D2 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction


cos_x cos_y cos_z

Working direction

planar_face 0.0 2.0 11.4 0.000 0.000 1.000 D1 round_hole –0.4 31.0 1.4 0.000 1.000 0.000 D2 round_hole 0.4 31.0 1.4 0.000 1.000 0.000 D2 round_hole 0.4 31.0 1.4 0.000 1.000 0.000 D2 round_hole 0.4 17.4 1.4 0.000 1.000 0.000 D2 round_hole 12.2 1.6 5.4 0.000 0.000 1.000 D1 replicate_feature 21.7 1.6 11.4 0.000 0.000 1.000 D1 (round_hole) 280_4 compound_feature 6.6 27.5 8.6 0.000 0.000 1.000 D1 280_5 compound_feature 6.6 27.5 11.4 0.000 0.000 1.000 D3 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction

280_1 280_2a 280_2b 280_2c 280_2d 280_2f 280_3b

Table 10.6 Machining features of product code 380 id_feature Abstract supertype x y z [mm] [mm] [mm] 380_1 380_11 380_12a 380_12b 380_13 380_14a 380_14b 380_16a 380_16b 380_16c 380_17 380_18 380_19a

cos_x

replicate_feature 6.8 17.2 20.6 0.000 (planar_face) planar_face 5.8 41.6 33.9 0.000 replicate_feature 4.1 24.2 8.9 0.000 (round_hole) compound_feature 4.1 24.2 8.9 0.000 planar_face 12.5 33.7 43.7 0.000 round_hole 10.9 9.5 29.6 0.000 compound_feature 10.9 9.5 29.6 0.000 compound_feature 18.2 41.6 33.9 0.000 compound_feature 29.8 41.6 33.9 0.000 replicate_feature 5.8 41.6 33.9 0.000 (round_hole) planar_face 24.6 48.9 57.1 0.000 replicate_feature 35.1 12.4 57.1 0.000 (round_hole) replicate_feature 18.8 3.3 57.1 0.000 (round_hole)

cos_y

cos_z

Working direction

1.000

0.000 D1

1.000 1.000

0.000 D2 0.000 D1

1.000 1.000 1.000 1.000 1.000 1.000 1.000

0.000 0.000 0.000 0.000 0.000 0.000 0.000

D1 D1 D1 D1 D2 D2 D2

0.000 1.000 D3 0.000 1.000 D3 0.000 1.000 D3

246


Table 10.6 (continued) id_feature Abstract supertype x [mm]

y [mm]

z [mm]

cos_x

cos_y

cos_z

Working direction

compound_feature 6.8 17.2 20.6 0.000 1.000 0.000 D1 replicate_feature 35.2 3.3 36.6 1.000 0.000 0.000 D4 (planar_face) 380_20c replicate_feature 35.2 3.3 36.6 1.000 0.000 0.000 D4 (round_hole) 380_21 planar_face 28.2 29.3 20.6 1.000 0.000 0.000 D4 380_22a replicate_feature 28.2 29.3 20.6 1.000 0.000 0.000 D4 (round_hole) 380_22b replicate_feature 28.2 29.3 20.6 1.000 0.000 0.000 D4 (round_hole) 380_3 replicate_feature 12.5 33.7 43.7 0.000 1.000 0.000 D1 (round_hole) 380_4 planar_face 12.2 33.7 20.6 0.906 0.423 0.000 D5 380_5 compound_feature 12.2 33.7 20.6 0.906 0.423 0.000 D5 380_6a replicate_feature 12.2 33.7 20.6 0.906 0.423 0.000 D5 (thread) 380_6b replicate_feature 12.2 33.7 20.6 0.906 0.423 0.000 D5 (thread) x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction 380_2 380_20a

Table 10.7 Machining features of product code 500 id_feature Abstract supertype x y z [mm] [mm] [mm] 500_1 500_10a 500_10b 500_11 500_12a 500_12b 500_16a 500_16ac 500_16b 500_2 500_3 500_4 500_5 500_6a 500_6b 500_7

planar_face compound_feature round_hole planar_face compound_feature compound_feature compound_feature compound_feature round_hole compound_feature replicate_feature (round_hole) planar_face compound_feature replicate_feature (round_hole) replicate_feature (round_hole) planar_face

48.0 42.5 42.5 64.5 55.0 55.0 64.5 64.5 64.5 48.0 64.5

0.2 35.8 35.8 24.2 2.8 2.8 20.2 16.0 20.2 0.2 24.2

16.9 40.0 40.0 34.4 14.5 14.5 51.0 30.2 51.0 16.9 34.4

cos_x

cos_y

cos_z Working direction

1.000 0.000 0.000 D1 0.000 1.000 0.000 D2 0.000 1.000 0.000 D2 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1 1.000 0.000 0.000 D1

43.1 43.1 43.1

8.8 16.9 8.8 16.9 8.8 16.9

0.420 0.420 0.420

0.910 0.000 D4 0.910 0.000 D4 0.910 0.000 D4

43.1

8.8 16.9

0.420

0.910 0.000 D4

12.5 37.8 16.9

0.000

1.000 0.000 D3

10

Testing

Table 10.7 (continued) id_feature Abstract supertype x [mm]

247

y [mm]

z [mm]

cos_x

cos_y

cos_z Working direction

replicate_feature 23.8 37.8 18.5 0.000 1.000 0.000 D3 (thread) 500_8b replicate_feature 23.8 37.8 18.5 0.000 1.000 0.000 D3 (thread) 500_9 planar_face 12.5 35.8 16.9 0.000 1.000 0.000 D2 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction 500_8a


cos_x cos_y

cos_z

Working direction

replicate_feature 16.0 43.9 76.8 0.000 1.000 0.000 D1 (round_hole) 900_12a compound_feature 16.0 12.4 60.6 0.000 0.000 1.000 D2 900_12b compound_feature 16.0 12.4 60.6 0.000 0.000 1.000 D2 900_15 replicate_feature 33.3 31.8 79.7 0.000 0.000 1.000 D2 (round_hole) 900_15A replicate_feature 17.0 40.2 79.7 0.000 0.000 1.000 D2 (round_hole) 900_21a round_hole 14.8 2.5 61.5 0.000 0.000 1.000 D2 900_21b compound_feature 14.8 2.5 61.5 0.000 0.000 1.000 D2 900_22a replicate_feature 40.0 6.2 75.5 0.000 0.000 1.000 D2 (planar_face) 900_22b replicate_feature 40.0 6.2 75.5 0.000 0.000 1.000 D2 (round_hole) 900_2a compound_feature 40.0 6.2 14.9 0.000 0.000 1.000 D2 900_2b replicate_feature 33.3 31.8 79.7 0.000 0.000 1.000 D2 (planar_face) 900_4 planar_face 16.0 5.5 50.9 0.000 1.000 0.000 D3 900_5 compound_feature 16.0 5.5 50.9 0.000 0.907 0.422 D4 900_6a replicate_feature 16.0 5.5 50.9 0.000 0.907 0.422 D4 (thread) 900_6b replicate_feature 16.0 5.5 50.9 0.000 0.907 0.422 D4 (thread) 900_7 planar_face 16.0 30.1 11.1 0.000 1.000 0.000 D3 900_8a replicate_feature 57.6 30.1 2.6 0.000 1.000 0.000 D3 (thread) 900_8b replicate_feature 57.6 30.1 2.6 0.000 1.000 0.000 D3 (thread) 900_9 planar_face 16.0 43.9 76.8 0.000 1.000 0.000 D1 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction 900_10

248


Table 10.9 Machining operations id_oper its_tool type id_oper its_tool type o0 0 Rolling o56 56 o1 1 Milling o57 57 o2 2 Milling o60 60 o3 3 Drilling o61 61 o4 4 Drilling o63 63 o5 5 Drilling o65 65 o6 6 Milling o67 67 o7 7 Milling o78 78 o8 8 Milling o80 80 o9 9 Drilling o81 81 o15 15 Drilling o85 85 o16 16 Drilling o97 97 o17 17 Threading o101 101 o19 19 Centering o102 102 o20 20 Drilling o111 111 o27 27 Boring o112 112 o28 28 Drilling o121 121 o50 50 Milling o123 123 o52 52 Drilling o131 131 o53 53 Milling o132 132 o55 55 Milling id_oper = id_operation; type = operation_type

id_oper its_tool type

Milling Milling Drilling Drilling Drilling Milling Drilling Milling Drilling Drilling Milling Drilling Drilling Drilling Drilling Threading Drilling Drilling Drilling Milling

o141 o142 o181 o182 o183 o211 o221 o222 o231 o241 o251 o252 o261 o262 o311 o322 o333 o344 o355 o651

141 142 181 182 183 211 221 222 231 241 251 252 261 262 311 322 333 344 355 651

Drilling Milling Milling Drilling Milling Drilling Drilling Milling Drilling Drilling Drilling Milling Drilling Drilling Boring Drilling Drilling Drilling Drilling Drilling

Using data concerning machining features and machining operations, the whole set of machining workingsteps has been defined, in accordance to the data formalization of Chap. 4 (see Sect. 4.3.3 and Table 4.16). In Tables 10.10 and 10.11 all the machining workingsteps are reported together with their cutting time.

Table 10.10 Machining workingsteps of product codes 240, 260, 270 and 280 mws its_feature oper time [s] mws its_feature oper

time [s]

ws01 ws02 ws03 ws04 ws05 ws06 ws07 ws08 ws09 ws10 ws11 ws12

5 4.22 5.5 5.29 5.49 5.47 2.34 5.46 4.02 4.8 4.75 6.1

240_1A 240_1B 240_5a 240_2d 240_2a 240_2b 240_6 240_7 240_8A 240_8B 240_5b 240_2c

o8 o8 o9 o101 o111 o121 o131 o141 o27 o27 o16 o0

3.05 3.05 6.1 3.81 4.49 5.42 5.06 3.69 2.95 2.95 6.07 5.04

ws22 ws23 ws24 ws25 ws26 ws27 ws28 ws29 ws30 ws31 ws32 ws95

260_2d 260_10c 270_1 270_4 270_a 270_b 270_e 270_3b 270_2d 270_15 270_2c 280_1

o241 o231 o181 o251 o261 o121 o85 o27 o28 o81 o0 o183

10

Testing

Table 10.10 (continued) mws its_feature oper

249

time [s]

mws

its_feature

ws13 260_1 o181 4.95 ws96 280_4 ws14 260_7a o19 3.51 ws97 280_5 ws15 260_10b o20 2.81 ws98 280_2a ws16 260_2c o20 2.19 ws99 280_2b ws17 260_2a o211 4.97 ws100 280_3b ws18 260_2b o121 4.95 ws101 280_2d ws19 260_2e o0 3.85 ws102 280_2c ws20 260_7b o221 4.96 ws103 280_2f ws21 260_11 o97 4.01 mws = id_workingstep; oper = its_operation; time = ws_cutting_time

oper

time [s]

o344 o355 o261 o123 o311 o322 o0 o333

5.3 4.3 5.5 5.8 6 4.1 5.35 4.4

Table 10.11 Machining workingsteps of product codes 380, 500 and 900 mws its_feature oper time [s] mws its_feature oper ws52 380_21 o50 6.37 ws40 500_7 ws53 380_20a o50 6.37 ws41 500_8a ws54 380_4 o50 8.17 ws42 500_8b ws55 380_11 o53 13.2 ws43 500_6a ws56 380_16a o52 4.59 ws44 500_6b ws57 380_16b o52 3.17 ws45 500_5 ws58 380_13 o53 4.67 ws46 500_3 ws59 380_14a o262 5.97 ws47 500_12a ws60 380_14b o55 5.78 ws48 500_12b ws61 380_16c o56 4.48 ws49 500_16b ws62 380_17 o57 8.55 ws50 500_10a ws63 380_1 o78 16.4 ws51 500_10b ws64 380_2 o252 4.57 ws76 900_9 ws65 380_3 o63 7.88 ws77 900_22a ws66 380_22a o102 8.88 ws78 900_22b ws67 380_22b o102 7.42 ws79 900_15 ws68 380_20c o60 16.8 ws80 900_21a ws69 380_12a o61 3.63 ws81 900_21b ws70 380_19a o60 7.97 ws82 900_15A ws71 380_18 o651 7.85 ws83 900_2a ws72 380_5 o222 9.67 ws84 900_12a ws73 380_6a o17 5.28 ws85 900_4 ws74 380_6b o17 5.82 ws86 900_7 ws75 380_12b o182 8.83 ws87 900_8a ws33 500_9 o65 17.6 ws88 900_8b ws34 500_11 o53 10.3 ws89 900_6a ws35 500_16a o52 4.47 ws90 900_6b ws36 500_16ac o52 3.15 ws91 900_5 ws37 500_1 o78 13.4 ws92 900_2b ws38 500_2 o251 4.57 ws93 900_12b ws39 500_4 o78 9.02 ws94 900_10 mws = id_workingstep; oper = its_operation; time = ws_cutting_time

o78 o17 o17 o111 o111 o221 o211 o231 o241 o56 o67 o67 o1 o2 o3 o4 o5 o6 o4 o7 o80 o1 o1 o102 o102 o112 o112 o222 o132 o142 o15

time [s] 8.94 4.18 8.35 4.65 8.18 5.15 8.55 8.63 4.83 4.53 10.5 7.41 17.9 3.77 8.34 4.59 5.48 5.33 6.82 9 9.27 7.17 10.7 5 11.7 4.65 8.18 5.15 12.3 4.79 15.4

250


Moreover, technological constraints among machining workingsteps must be considered. These constraints can be precedence constraints (i.e. a machining workingstep must be executed after another one) or tolerance constraints (i.e. two machining workingsteps must be processed on the same machine and same setup in order to guarantee the required precision level). Precedence constraints are reported in Table 10.12, while tolerance constraints are given in Table 10.13.

Table 10.12 Precedence constraints among machining workingsteps pred succ pred succ pred succ ws01 ws07 ws27 ws30 ws01 ws09 ws30 ws32 ws02 ws10 ws33 ws50 ws03 ws11 ws34 ws35 ws04 ws05 ws34 ws36 ws05 ws06 ws35 ws49 ws06 ws12 ws36 ws49 ws101 ws102 ws37 ws38 ws14 ws20 ws37 ws46 ws15 ws23 ws39 ws43 ws16 ws17 ws39 ws45 ws17 ws18 ws40 ws41 ws18 ws19 ws41 ws42 ws19 ws22 ws43 ws44 ws24 ws29 ws47 ws48 ws26 ws27 ws50 ws51 pred = predecessor; succ = successor

ws52 ws53 ws54 ws54 ws55 ws55 ws56 ws57 ws58 ws59 ws62 ws62 ws63 ws63 ws66 ws69

ws66 ws68 ws72 ws73 ws56 ws57 ws61 ws61 ws59 ws60 ws70 ws71 ws64 ws65 ws67 ws75

Table 10.13 Tolerance constraints among machining workingsteps mws1 mws2 mws1 mws2 mws1

pred

succ

ws73 ws76 ws77 ws79 ws80 ws83 ws84 ws85 ws85 ws86 ws87 ws89 ws95 ws98 ws99

ws74 ws94 ws78 ws82 ws81 ws92 ws93 ws89 ws91 ws87 ws88 ws90 ws100 ws99 ws101

mws2

ws01 ws02 ws26 ws27 ws53 ws62 ws03 ws11 ws27 ws30 ws56 ws57 ws06 ws12 ws30 ws32 ws58 ws59 ws09 ws10 ws35 ws36 ws59 ws60 ws14 ws20 ws37 ws38 ws63 ws64 ws15 ws16 ws41 ws42 ws69 ws75 ws16 ws17 ws43 ws44 ws96 ws97 ws17 ws18 ws46 ws47 ws97 ws100 ws18 ws19 ws49 ws50 ws98 ws99 ws22 ws23 ws50 ws51 ws99 ws102 mws1 = first machining workingstep of the couple of wokingsteps that must be executed on the same pallet and on the same machine; mws2 = second machining workingstep of the couple of wokingsteps that must be executed on the same pallet and on the same machine

10

Testing

251

10.2.2 Railway Components The family of products for railway applications consist of two products: ‘‘cannotto’’ (product code 101) and ‘‘catenaccio’’ (product code 102). For each workpiece type a 3D drawing is reported in Figs. 10.8 and 10.9.

Fig. 10.8 Product code 101

Fig. 10.9 Product code 102

Table 10.14 provides the information on the material and the dimensions related to the bounding geometry. As for the first family, each workpiece type has been technologically analyzed and the information has been formalized according to the framework provided in Chap. 4. Starting from the list of machining feature, described by direction cosines, it is possible to determine the corresponding working directions. In particular, the data concerning the machining features are listed in Tables 10.15 and 10.16. Figures 10.10 and 10.11 illustrate the working directions.

252


Table 10.14 Characteristics and dimensions of the workpiece types id_workpiece its_material x_pos x_neg y_pos y_neg [mm] [mm] [mm] [mm]

z_pos [mm]

z_neg [mm]

101

41CrMo435 –35 38 –38 215 –215 UNI8551 102 41CrMo415 –15 350 0 120 0 UNI8551 x_pos = x_bounding_pos; x_neg = x_bounding_neg; y_pos = y_bounding_pos; y_neg = y_bounding_neg; z_pos = z_bounding_pos; z_neg = z_bounding_neg

Table 10.15 Machining features of product code 101 id_feature Abstract x y z supertype [mm] [mm] [mm]

cos_x

cos_y

cos_z

Working direction

101BH01 button_hole 0 –38 130 0 –1 0 D5 101BH02 button_hole 0 –38 –130 0 –1 0 D5 101Ch01 round_hole –35 –28 –185 –1 0 0 D4 101Ch02 round_hole –35 –28 185 –1 0 0 D4 101Ch03 round_hole –35 –3 –174 –1 0 0 D4 101Ch04 round_hole –35 –3 174 –1 0 0 D4 101Ch05 round_hole 35 –28 –185 1 0 0 D1 101Ch06 round_hole 35 –28 185 1 0 0 D1 101Ch07 round_hole 35 –3 –174 1 0 0 D1 101Ch08 round_hole 35 –3 174 1 0 0 D1 101Ch09 planar_face 27.5 38 –98 1 0 0 D1 101Ch11 button_hole 0 –38 130 0 –1 0 D5 101Ch12 planar_face 0 38 31.75 1 0 0 D1 101Ho01 round_hole –35 –28 –185 –1 0 0 D4 101Ho02 round_hole –35 –28 185 –1 0 0 D4 101Ho03 round_hole –35 –3 –174 –1 0 0 D4 101Ho04 round_hole –35 –3 174 –1 0 0 D4 101Ho05 round_hole 35 –28 –185 1 0 0 D1 101Ho06 round_hole 35 –28 185 1 0 0 D1 101Ho07 round_hole 35 –3 –174 1 0 0 D1 101Ho08 round_hole 35 –3 174 1 0 0 D1 101Ho09 round_hole 0 0 –215 0 0 –1 D6 101Ho10 round_hole 0 0 215 0 0 1 D3 101Ho11 round_hole 0 38 –206 0 1 0 D2 101Ho12 round_hole 0 38 206 0 1 0 D2 101PF01 planar_face 0 38 0 0 1 0 D2 101PF02 planar_face –35 0 0 –1 0 0 D4 101PF03 planar_face 0 –38 0 0 –1 0 D5 101PF04 planar_face 35 0 0 1 0 0 D1 101PF05 planar_face 0 0 –215 0 0 –1 D6 101PF06 planar_face 0 0 215 0 0 1 D3 101PF07 planar_face 27.5 38 –98 1 0 0 D1 101PF08 planar_face –27.5 38 98 1 0 0 D1 101PF09 planar_face 0 38 31.75 1 0 0 D1 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction

10

Testing

Table 10.16 Machining features of product code 102 id_feature Abstract x y z cos_x supertype [mm] [mm] [mm]

253

cos_y

cos_z

Working direction

102Ho1 Hole 15 129.5 60 1 0 0 D1 102Ho10 Hole 15 49 18 1 0 0 D1 102Ho11 Hole 15 120 104 1 0 0 D1 102Ho12 Hole 15 139 104 1 0 0 D1 102Ho13 Hole 15 120 18 1 0 0 D1 102Ho14 Hole 15 139 18 1 0 0 D1 102Ho2 Hole 15 39.5 60 1 0 0 D1 102Ho3 Hole –15 129.5 60 –1 0 0 D4 102Ho4 Hole –15 39.5 60 –1 0 0 D4 102Ho5 round_hole 0 69.5 120 0 0 1 D3 102Ho6 round_hole 0 99.5 120 0 0 1 D3 102Ho7 Hole 15 30 104 1 0 0 D1 102Ho8 Hole 15 49 104 1 0 0 D1 102Ho9 Hole 15 30 18 1 0 0 D1 102PF01 planar_face 0 84.5 120 0 0 1 D3 102PF02 planar_face –15 175 60 –1 0 0 D4 102PF03 planar_face 0 350 24 0 1 0 D2 102PF04 planar_face 0 0 60 0 –1 0 D5 102PF05 planar_face 0 199 48 0 0 1 D3 102PF06 planar_face 0 330 48 0 0 1 D3 102PF0506 planar_face 0 264 48 0 0 1 D3 102PF07 planar_face 0 300 28 0 0 1 D3 102PF08 planar_face 0 209 28 0 0 1 D3 102PF09 planar_face 0 249.5 18 0 0 1 D3 102PF10 planar_face 0 169 84 0 1 0 D2 102PF11 planar_face 15 175 60 1 0 0 D1 102PF12 planar_face 0 175 0 0 0 –1 D6 x = placement_location_x; y = placement_location_y; z = placement_location_z; (cos_x, cos_y, cos_z) = direction cosines of the working direction

Fig. 10.10 Working directions of product code 101

254


Fig. 10.11 Working directions product code 102

Once the machining features have been determined, the machining operations can be defined (Tables 10.17 and 10.18). As defined in Chap. 4, each operation can be characterised by its type and the required tool. Tools are synthetically indicated discarding technical details and paying attention to the operation type. The machining workingsteps are listed in Tables 10.19 and 10.20. Table 10.17 Machining operations of product code 101 id_oper its_tool type id_oper 101Mi01 T01 Milling 101Mi02 T02 Milling 101Mi03 T02 Milling 101Mi04 T03 Milling 101Mi05 T03 Milling 101Mi06 T03 Milling 101Dr01 T04 Drilling 101Dr02 T05 Drilling 101Ch01 T05 Chamfering 101Ch02 T06 Chamfering 101Bo01 T07 Boring 101Dr03 T04 Drilling 101Bo02 T07 Boring 101Mi07 T03 Milling 101Ce01 T09 Centering 101Dr04 T09 Drilling 101Mi09 T03 Milling 101Dr06 T05 Drilling 101Ch03 T10 Chamfering 101Ch04 T11 Chamfering id_oper = id_operation; type = operation_type

101Mi10 101Th03 101Mi11 101Ch05 101Bo03 101Dr07 101Dr12 101Ch06 101Dr09 101Gr01 101Th01 101Bo05 101Dr11 101Mi11 101Ch11 101Ch12 101Mi12 101Mi13 101Ce03

its_tool

type

T12 T29 T13 T14 T15 T16 T28 T17 T18 T19 T20 T21 T22 T13 T24 T25 T23 T27 T28

Milling Threading Milling Chamfering Boring Drilling Drilling Chamfering Drilling Groove Threading Boring Drilling Milling Chamfering Chamfering Milling Milling Centering

10

Testing

255

Table 10.18 Machining operations of product code 102 id_oper its_tool type id_oper

its_tool

type

TT10 TT11 TT12 TT13 TT14 TT15 TT16 TT02 TT06 TT17 TT18

Milling Milling Milling Drilling Milling Milling Milling Milling Milling Drilling Milling

Table 10.19 Machining workingsteps of product code 101 mws its_feature oper time mws [s]

its_feature oper

time [s]

1BnH01D11 1BnH01M11 1BnH02D11 1BnH02M11 1Chmf01CH01 1Chmf02CH01 1Chmf03CH02 1Chmf04CH02 1Chmf05CH04 1Chmf06CH04 1Chmf07CH03 1Chmf07CH11 1Chmf08CH03 1Chmf08CH11 1Chmf09CH05 1Chmf09CH12 1H01B01 1H01D01 1H02B01 1H02D01 1H03D02 1H04D02 1H05B02 1H05D03 1H06B02 1H06D03 1H07D06 1H08D06

101Ho09 101Ho09 101Ho09 101Ho09 101Ho10 101Ho10 101Ho10 101Ho10 101Ho10 101Ho10 101Ho10 101Ho10 101Ho11 101Ho11 101Ho11 101Ho12 101Ho12 101Ho12 101PF01 101PF01 101PF02 101PF03 101PF04 101PF05 101PF05 101PF06 101PF06 101PF07

297 186 396 135 213 135 54 135 45 297 186 135 36 39 72 36 39 498 498 366 420 498 120 138 99 204 99 90

102Mi01 TT01 Milling 102Mi02 TT02 Milling 102Mi03 TT02 Milling 102Dr01 TT03 Drilling 102Mi04 TT04 Milling 102Mi06 TT06 Milling 102Mi07 TT06 Milling 102Mi08 TT07 Milling 102Mi09 TT07 Milling 102Mi10 TT08 Milling 102Mi11 TT09 Milling id_oper = id_operation; type = operation_type

101BH01 101BH01 101BH02 101BH02 101Ch01 101Ch02 101Ch03 101Ch04 101Ch05 101Ch06 101Ch07 101Ch07 101Ch08 101Ch08 101Ch09 101Ch09 101Ho01 101Ho01 101Ho02 101Ho02 101Ho03 101Ho04 101Ho05 101Ho05 101Ho06 101Ho06 101Ho07 101Ho08

101Dr11 101Mi11 101Dr11 101Mi11 101Ch01 101Ch01 101Ch02 101Ch02 101Ch04 101Ch04 101Ch03 101Ch11 101Ch03 101Ch11 101Ch05 101Ch12 101Bo01 101Dr01 101Bo01 101Dr01 101Dr02 101Dr02 101Bo02 101Dr03 101Bo02 101Dr03 101Dr06 101Dr06

19 19 19 19 36 36 36 36 54 54 54 24 54 24 72 24 63 63 63 63 63 63 23 27 23 27 117 117

102Mi12 102Mi13 102Mi14 102Dr02 102Mi15 102Mi16 102Mi17 102Mi18 102Mi19 102Dr03 102Mi21

1H09D07 1H09D09 1H09GR01 1H09TH01 1H10B03 1H10B05 1H10C01 1H10CH06 1H10D04 1H10D07 1H10D09 1H10TH01 1H11C03 1H11D12 1H11TH03 1H12C03 1H12D12 1H12TH03 1Pf01M01 1Pf01M09 1Pf02M02 1Pf03M03 1Pf04M04 1Pf05M05 1Pf05M07 1Pf06M06 1Pf06M07 1Pf07M10

101Dr07 101Dr09 101Gr01 101Th01 101Bo03 101Bo05 101Ce01 101Ch06 101Dr04 101Dr07 101Dr09 101Th01 101Ce03 101Dr12 101Th03 101Ce03 101Dr12 101Th03 101Mi01 101Mi09 101Mi02 101Mi03 101Mi04 101Mi05 101Mi07 101Mi06 101Mi07 101Mi10

256 Table 10.19 (continued) mws its_feature oper


time [s]

mws

its_feature oper

time [s]

1H09B03 101Ho09 101Bo03 213 1Pf07M13 101PF07 101Mi13 66 1H09B05 101Ho09 101Bo05 135 1Pf08M10 101PF08 101Mi10 90 1H09C01 101Ho09 101Ce01 54 1Pf08M13 101PF08 101Mi13 66 1H09CH06 101Ho09 101Ch06 135 1Pf09M11 101PF09 101Mi11 66 1H09D04 101Ho09 101Dr04 45 1Pf09M12 101PF09 101Mi12 144 mws = id_workingstep; feat = its_feature; oper = its_operation; time = ws_cutting_time

Table 10.20 Machining workingsteps of product code 102 mws its_feature oper time [s] mws its_feature

oper

2H10D03 102Ho10 102Dr03 26 2Pf01M12 102PF01 102Mi12 2H11D03 102Ho11 102Dr03 26 2Pf02M02 102PF02 102Mi02 2H12D03 102Ho12 102Dr03 26 2Pf02M06 102PF02 102Mi06 2H1D01 102Ho1 102Dr01 108 2Pf03M03 102PF03 102Mi03 2H2D01 102Ho2 102Dr01 108 2Pf03M07 102PF03 102Mi07 2H3M04 102Ho3 102Mi04 102 2Pf04M03 102PF04 102Mi03 2H3M21 102Ho3 102Mi21 108 2Pf04M07 102PF04 102Mi07 2H4M04 102Ho4 102Mi04 102 2Pf05M11 102PF05 102Mi11 2H4M21 102Ho4 102Mi21 108 2Pf05M14 102PF05 102Mi14 2H5D02 102Ho5 102Dr02 44 2Pf06M11 102PF06 102Mi11 2H5D03 102Ho5 102Dr03 26 2Pf06M14 102PF06 102Mi14 2H5M15 102Ho5 102Mi15 39 2Pf07M11 102PF07 102Mi11 2H5M16 102Ho5 102Mi16 33 2Pf07M14 102PF07 102Mi14 2H5M17 102Ho5 102Mi17 36 2Pf08M11 102PF08 102Mi11 2H6D02 102Ho6 102Dr02 44 2Pf08M14 102PF08 102Mi14 2H6D03 102Ho6 102Dr03 26 2Pf09M11 102PF09 102Mi11 2H6M15 102Ho6 102Mi15 39 2Pf09M13 102PF09 102Mi13 2H6M16 102Ho6 102Mi16 33 2Pf10M10 102PF10 102Mi10 2H6M17 102Ho6 102Mi17 36 2Pf10M13 102PF10 102Mi13 2H7D03 102Ho7 102Dr03 26 2Pf11M18 102PF11 102Mi18 2H8D03 102Ho8 102Dr03 26 2Pf11M19 102PF11 102Mi19 2H9D03 102Ho9 102Dr03 26 2Pf12M08 102PF12 102Mi08 2Pf01M01 102PF01 102Mi01 225 2Pf12M12 102PF12 102Mi12 2Pf01M08 102PF01 102Mi08 54 2Pf56M09 102PF0506 102Mi09 mws = id_workingstep; oper = its_operation; time = ws_cutting_time

time [s] 51 132 210 111 96 111 96 22.4 27 22.4 27 22.4 27 22.4 27 22.4 69 108 69 138 222 54 51 126

For example, referring to product code 102, the machining workingstep 2Pf01M01 includes information on the milling operation 102Mi01 (using tool type TT01) that is performed on the feature 102PF01 (that is the planar face perpendicular to the working direction D1). Once machining workingsteps have been determined, the technological constraints among machining workingsteps should be analyzed. For instance, the precedence relation between workingsteps 2Pf02M02 (predecessor) and

10

Testing

257

2H1D01 (successor) stands for the necessity to execute first the milling of planar face 102PF02 and then the drilling of hole 101Ho01 on such a planar face. Tables 10.21 and 10.22 provide the complete list of precedence constraints for product code 101 and 102 respectively.

Table 10.21 Precedence constraints among machining workingsteps of product code 101 Predecessor Successor Predecessor Successor 1Pf04M04 1Pf04M04 1Pf04M04 1Pf04M04 1H01D01 1H02D01 1H03D01 1H04D01 1Chmf01CH01 1Chmf02CH01 1H06D03 1H05D03 1Pf05M07 1H09C01 1Pf06M07 1H10C01 1Pf01M09 1Pf01M09 1Pf01M09 1Pf01M09 1Pf01M09 1H07D06 1H08D06

1H01D01 1H02D01 1H03D01 1H04D01 1Chmf01CH01 1Chmf02CH01 1Chmf03CH02 1Chmf04CH02 1H01B01 1H02B01 1H06B02 1H05B02 1H09C01 1H09D04 1H10C01 1H10D04 1H07D06 1H08D06 1Chmf05CH04 1Chmf06CH04 1Pf09M11 1Chmf07CH03 1Chmf08CH03

1Pf07M10 1Pf08M10 1H09B03 1H09D07 1Chmf05CH05 1H10B03 1H10D07 1Chmf06CH05 1H09D09 1H10D09 1H09GR01 1H09GR01 1H09TH01 1H10TH01 1BH01D12 1BH01M11 1BH02D12 1BH02M11 1Chmf09CH12 1H11C03 1H11D12 1H12C03 1H12D12

1Chmf09CH05 1Chmf09CH05 1H09D07 1Chmf05CH05 1H09D09 1H10D07 1Chmf06CH05 1H10D09 1H09GR01 1H09GR01 1H09TH01 1H10TH01 1H09B05 1H10B05 1BH01M11 1Chmf07CH11 1BH02M11 1Chmf08CH11 1Pf09M12 1H11D12 1H11TH03 1H12D12 1H12TH03

Table 10.22 Precedence constraints among machining workingsteps of product code 102 Predecessor Successor Predecessor Successor Predecessor Successor 2Pf02M02 2Pf02M02 2Pf02M02 2H1D01 2H2D01 2Pf03M03 2Pf04M03 2Pf01M08 2H5M17 2H5M16

2H1D01 2H2D01 2Pf02M06 2H3M04 2H4M04 2Pf03M07 2Pf04M07 2H5M17 2H5M16 2H5M15

2H5M15 2Pf01M08 2H6M17 2H6M16 2H6M15 2Pf01M08 2Pf12M08 2Pf56M09 2Pf05M11 2Pf56M09

2H5D02 2H6M17 2H6M16 2H6M15 2H6D02 2Pf01M12 2Pf12M12 2Pf05M11 2Pf05M14 2Pf06M11

2Pf06M11 2Pf56M09 2Pf07M11 2Pf56M09 2Pf08M11 2Pf56M09 2Pf09M11 2Pf56M09 2Pf10M10 2Pf11M18

2Pf06M14 2Pf07M11 2Pf07M14 2Pf08M11 2Pf08M14 2Pf09M11 2Pf09M13 2Pf10M10 2Pf10M13 2Pf11M19

258


10.2.3 Hydraulic Components In this section a product belonging to the family of high-pressure valve coupling flanges will be described. The choice of the product type has been driven by the product geometric and technological complexity related to the presence of a radial passing hole, designed for lubrication. Figure 10.12 illustrates a 3D drawing of the product code N016A.

Fig. 10.12 Product code N016A

Information concerning the material and the bounding geometry (i.e. the envelope cube) is listed in Table 10.23. In particular, the material is steel AISI 316 and the origin of the workpiece coordinate system is placed in the center of its envelope cube. The working directions that are necessary to process the workpiece are shown in Fig. 10.13.

Table 10.23 Characteristics and dimensions of the workpiece type id_workpiece its_material x_pos x_neg y_pos y_neg [mm] [mm] [mm] [mm]

z_pos [mm]

z_neg [mm]

N016A

23.75

23.75

AISI 316

64.00

–64.00

64.00

–64.00

Fig. 10.13 Working directions

Each machining feature has been described in Table 10.24, on the basis of the coordinate system shown in Fig. 10.13 and the definitions of Table 4.2.

10

Testing

Table 10.24 Machining features of product code N016A id_feature Abstract x y z cos_x supertype [mm] [mm] [mm] 016_1_A round_hole –38.9 38.9 –20.0 0 016_1_B round_hole –38.9 38.9 –20.0 0 016_2_A round_hole –44.7 19.0 –20.0 0 016_2_B round_hole –44.7 19.0 –20.0 0 016_3_A round_hole –45.3 –19.2 –20.0 0 016_3_B round_hole –45.3 –19.2 –20.0 0 016_3_C round_hole –45.3 –19.2 –7.5 0 016_4_A round_hole –38.9 –38.9 –20.0 0 016_4_B round_hole –38.9 –38.9 –20.0 0 016_5_A round_hole –19.0 –44.7 –20.0 0 016_5_B round_hole –19.0 –44.7 –20.0 0 016_6_A round_hole 19.2 –45.3 –20.0 0 016_6_B round_hole 19.2 –45.3 –20.0 0 016_6_C round_hole 19.2 –45.3 –7.5 0 016_7_A round_hole 38.9 –38.9 –20.0 0 016_7_B round_hole 38.9 –38.9 –20.0 0 016_8_A round_hole 44.7 –19.0 –20.0 0 016_8_B round_hole 44.7 –19.0 –20.0 0 016_9_A round_hole 45.3 19.2 –20.0 0 016_9_B round_hole 45.3 19.2 –20.0 0 016_9_C round_hole 45.3 19.2 –7.5 0 016_10_A round_hole 38.9 38.9 –20.0 0 016_10_B round_hole 38.9 38.9 –20.0 0 016_11_A round_hole 19.0 44.7 –20.0 0 016_11_B round_hole 19.0 44.7 –20.0 0 016_12_A round_hole –19.2 45.3 –20.0 0 016_12_B round_hole –19.2 45.3 –20.0 0 016_12_C round_hole –19.2 45.3 –7.5 0 016_13_A round_hole 0.0 65.0 –4.2 0 016_13_B round_hole 0.0 65.0 –4.2 0 016_13_C round_hole 0.0 59.2 –4.2 0 x = placement_location_x; y = placement_location_y; z = cos_y, cos_z) = direction cosines of the working direction

259

cos_y

cos_z

Working direction

0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 0 1 D1 1 0 D2 1 0 D2 1 0 D2 placement_location_z; (cos_x,

As shown in Fig. 10.13, some machining operations are characterized by the same working direction. Herein, the concept of replicated feature allows to simplify the product representation. Indeed, a group of identical features can be described by defining the number and the spacing of the features. This is the case of the circle of holes and the mesh of holes (ISO/FDIS 14649-10). In this way, the machining features reported in Table 10.24 can be condensed in the replicate features that are defined in Table 10.25. ‘‘Circular_pattern’’ is a specific type of replicate feature object and describes the pattern assumed by

260


Table 10.25 Replicate features of product code N016A Replicate feature Associated features Number of features

Base diameter

Angle increment

circular_pattern_1

4

68.59

908

4

68.59

908

4

68.59

908

4

73.33

908

4

73.33

908

4

68.59

908

4

68.59

908

circular_pattern_2 circular_pattern_3 circular_pattern_4 circular_pattern_5 circular_pattern_6 circular_pattern_7

016_3_A, 016_6_A, 016_9_A, 016_12_A 016_3_B, 016_6_B, 016_9_B, 016_12_B 016_3_C, 016_6_C, 016_9_C, 016_12_C 016_1_A, 016_4_A, 016_7_A, 016_10_A 016_1_B, 016_4_B, 016_7_B, 016_10_B 016_2_A, 016_5_A, 016_8_A, 016_11_A 016_2_B, 016_5_B, 016_8_B, 016_11_B

the group of features (‘‘Associated features’’). Table 10.25 lists the main attributes necessary to formalize a circular pattern replicate feature, i.e. the total number of features in the replicate feature, the diameter of the circular pattern and the angle between two elements of the pattern. The information regarding machining operation and machining workingsteps (see Sect. 4.6 and Table 4.16) is reported in the following tables. In particular, Table 10.26 shows the machining operations, including the tool diameter. Due to the small diameter which characterizes the lubrication hole, the related machining operation (no. 5 in Table 10.26) is performed by a very low feed rate: this facilitates chip removal, avoiding a premature failure of the tool. Table 10.27 presents the list of machining workingsteps and the related cutting times. Precedence and tolerance constraints among the machining workingsteps are reported in Tables 10.28 and 10.29 respectively.

Table 10.26 Machining operations of product code N016A id_oper type Spindle speed Feed rate [rpm] [mm/round] n1 Centering 500 n2 Drilling 1200 n3 Spot-facing 1000 n4 Countersinck cutter 800 n5 Drilling 400 id_oper = id_operation; type = operation_type

0.1 0.1 0.1 0.1 0.01

Tool diameter [mm] 5 25 13 12 (max) 4

10

Testing

261

Table 10.27 Machining workingsteps of product code N016A mws its_feature oper time [s] mws its_feature

oper

ws01 016_1A n1 3.6 ws17 016_8A n1 ws02 016_1B n2 16.25 ws18 016_8B n2 ws03 016_2A n1 3.6 ws19 016_9A n1 ws04 016_2B n2 16.25 ws20 016_9B n2 ws05 016_3A n1 3.6 ws21 016_9C n3 ws06 016_3B n3 16.25 ws22 016_10A n1 ws07 016_3C n2 7.5 ws23 016_10B n2 ws08 016_4A n1 3.6 ws24 016_11A n1 ws09 016_4B n2 16.25 ws25 016_11B n2 ws10 016_5A n1 3.6 ws26 016_12A n1 ws11 016_5B n2 16.25 ws27 016_12B n2 ws12 016_6A n1 3.6 ws28 016_12C n3 ws13 016_6B n3 6.25 ws29 016_13A n1 ws14 016_6C n2 7.5 ws30 016_13B n4 ws15 016_7A n1 3.6 ws31 016_13C n5 ws16 016_7B n2 16.25 mws = id_workingstep; oper = its_operation; time = ws_cutting_time [s]

time [s] 3.6 16.25 3.6 16.25 7.5 3.6 16.25 3.6 16.25 3.6 16.25 7.5 3.6 2.25 390

Table 10.28 Precedence constraints among machining workingsteps of product code N016A pred succ pred succ pred succ pred succ pred succ ws01 ws02 ws08 ws09 ws15 ws03 ws04 ws10 ws11 ws15 ws05 ws06 ws12 ws13 ws19 ws06 ws07 ws13 ws14 ws20 pred = predecessor; succ = successor

ws16 ws18 ws20 ws21

ws22 ws24 ws26 ws27

ws23 ws25 ws27 ws28

ws29 ws30

ws30 ws31

Table 10.29 Tolerance constraints among machining workingsteps of product code N016A mws1 mws2 mws1 mws2 mws1 mws2 mws1 mws2 ws01 ws14 ws06 ws13 ws02 ws06 ws04 ws11 ws21 ws28 ws20 ws27 ws09 ws16 ws18 ws25 ws07 ws28 ws06 ws27 ws16 ws23 ws04 ws25 ws21 ws14 ws20 ws13 ws02 ws16 ws18 ws11 ws07 ws21 ws06 ws20 ws23 ws09 ws25 ws04 ws14 ws28 ws13 ws27 ws01 ws23 ws18 ws11 mws1 = first machining workingstep of the couple of wokingsteps that must be executed on the same pallet and on the same machine; mws2 = second machining workingstep of the couple of wokingsteps that must be executed on the same pallet and on the same machine

262


10.3 Test Cases Speaking about FFMS one would like to have an answer to the following questions: 1. Are FFMSs cost effective compared to FMSs? 2. Are FFMS solutions robust? How does the production problem variability impact on the FFMS profitability? 3. Is it worth investing in a stochastic design approach to design an FFMS? Questions 1 has already been addressed in Chap. 7 where an extensive analysis has been carried out to study which is the impact of the production problem (e.g. the part family, the part mix and the aggregate demand) and of the database of selectable resources (e.g. cost and performance of the machines) on the performance and profitability of Focused Flexibility Manufacturing Systems. A set of testing experiments have been designed to address the remaining questions and to study: 1. The robustness of FFMS solutions towards changes in the production problem (see Sect. 10.4); 2. The advantage offered by a stochastic approach to design FFMSs (see Sect. 10.5); 3. The reliability of the system performance estimates obtained with the system design model (see Sect. 10.6). The design of the experiments has been developed starting from the analysis of the results already presented in Chap. 7. Before presenting the experiments and the related results in details, the following sub-sections define the general settings regarding the workpiece types (see Sect. 10.3.1), the selectable machines (see Sect. 10.3.2) and the process planning (see Sect. 10.3.3).

10.3.1 Workpiece Types The workpiece types used to design the testing experiments have been selected from a set of 24 workpiece types. Some of these correspond to the products that have already been described in Sect. 10.2 (workpiece types 240, 260, 270, 280, 380, 500, 900, 101, 102 and N016A). The other workpiece types have been derived from this original set by applying some modifications (e.g. removal of features), thus creating new product versions (workpiece types 241, 261, 271, 281, 381, 501, 901, 242, 262, 272, 282, 382, 502, 902). The details regarding the definition of the part mix and the aggregate demand will be presented for each experiment in the following sections. Among the main characteristics of the workpiece types, much attention is paid to the operation types that are required to machine the products. Indeed, the types of operation strongly influence the possibility of obtaining system

10

Testing

263

solutions that are characterized by the presence of dedicated machines (see Sect. 7.9.2).

10.3.2 Machine Types As in Chap. 7, three main types of machines have been considered:

General purpose machines that can execute any kind of machining operation;

Roughing machines that can perform only roughing operations; Drilling machines that can process only drilling operations. In Chap. 7 it was shown how the cost of dedicated machines influences the profitability of the FFMS solutions, i.e. the difference between the cost of FMS and FFMS solutions. Therefore in this chapter the experiments have been carried out considering a set of selectable machines consisting of 9 machine types which differ one from another in terms of costs and performance. Of these machines one is a general purpose machine, four are drilling machines and four are roughing machines. The cost reduction of the roughing machines compared to the general purpose machine ranges from 25 to 40%, while the cost reduction of the drilling machines ranges from 15 to 30%. The higher is the cost reduction of the dedicated machines, the worse is their performance. Herein, the machine performance is assumed to impact on the total processing time: a machine with a higher performance can process a part type in a shorter time. All the machines along with their characteristics are reported in Table 10.30. The cost and performance of the dedicated machine are also compared to the general purpose machine, so that it is possible to calculate ‘‘ Machine Cost %’’ and ‘‘ Machine Performance %’’ (Table 10.30 and Fig. 10.14). Table 10.30 Selectable machine types id Precision Operation Machine machine level type cost [c.u.]

Machine Machine Machine cost % performance performance %

GP High All types 100 0 1 0 R1 Low All types 60 –40 0.65 –35 R2 Low All types 65 –35 0.75 –25 R3 Low All types 70 –30 0.85 –15 R4 Low All types 75 –25 0.95 –5 D1 High Only drilling 70 –30 1.05 5 D2 High Only drilling 75 –25 1.1 10 D3 High Only drilling 90 –20 1.15 15 D4 High Only drilling 85 –15 1.2 20 precision level = parameter equal to ‘‘low’’ if only roughing operations can be executed, while it is equal to ‘‘high’’ if both roughing and finishing operations can be executed; operation type = type of operation that can be executed (e.g. drilling, milling, all types, . . .)

264


Fig. 10.14 Cost and performance of the dedicated machines compared to the general purpose machine

10.3.3 Process Planning Process planning is the activity which defines the sequence of operations that are necessary to process the considered workpiece type by means of the selectable resources. The problem has already been addressed in detail within Chap. 6 and the developed methodology has been used to generate the input data required by the application of the FFMS design model presented in Sect. 7.6. The following tables present the main results of the process planning activity related to workpiece type 240 that has been described in Sect. 10.2 (see Sect. 10.2.1, Tables 10.2, 10.9, 10.10, 10.12 and Figs. 10.1 and 10.4). The first result concerns the setup planning (Table 10.31), i.e. how the workpieces should be positioned on the fixtures in order to execute the necessary machining operations. A setup is identified by three triplets of direction cosines; each triplet defines the position of one axis of the coordinate system of the workpiece with reference to the coordinate system of the machine. Once the setup planning (Contini and Tolio 2004) has been completed, it is possible to execute the pallet configuration activity (Table 10.32) defining the characteristics of the pallet types that will be adopted to process the workpiece types. The process planning provides as output the alternative process plans (Table 10.33) that can be adopted to obtain the demanded workpiece types. Moreover, the FFMS design model needs as input the feasible assignments of machining workingsteps to the types of machines and pallets (Table 10.34).

10

Testing

265

Table 10.31 Setup planning for product code 240 id id id N cos cos setup_face workpiece workingstep parts xx xy sf_1_240

cos xz

cos yx

cos yy

cos yz

cos zx

cos zy

cos zz

240

ws04, ws05, 15 1 0 0 0 1 0 0 0 1 ws06, ws12 sf_2_240 240 ws03, ws11 15 0 0 –1 0 1 0 1 0 0 sf_3_240 240 ws08 15 1 0 0 0 0 1 0 –1 0 sf_4_240 240 ws01, ws02, 15 –1 0 0 0 1 0 0 0 –1 ws07, ws09, ws10 N parts = number of parts clamped on the setup face; (cos xx, cos xy, cos xz) = direction cosines of the x-axis of the workpiece coordinate system; (cos yx, cos yy, cos yz) = direction cosines of the y-axis of the workpiece coordinate system; (cos zx, cos zy, cos zz) = direction cosines of the z-axis of the workpiece coordinate system

Table 10.32 Pallet types to process product code 240 id pallet id setup face

N setupface

N parts

PP01_1_240 PP01_2_240 PP01_3_240 PP01_4_240 PP01_5_240 PP01_6_240 PP01_7_240 PP01_8_240 PP01_9_240 PP01_10_240 PP01_11_240

4 4 4 4 2 2 2 1 2 2 2

60 60 60 60 60 60 60 60 60 60 60

sf_1_240 sf_2_240 sf_3_240 sf_4_240 sf_1_240, sf_2_240 sf_1_240, sf_3_240 sf_1_240, sf_4_240 sf_1_240, sf_2_240, sf_3_240, sf_4_240 sf_2_240, sf_3_240 sf_2_240, sf_4_240 sf_3_240, sf_4_240

Table 10.33 Workplans for product code 240 id workplan id workpiece id workingstep

Pallet sequence

Wplan_240_0

240

ws01, ws02, ws03, ws04, ws05, ws06, ws07, ws08, ws09, ws10, ws11, ws12

PP01_5_240, PP01_11_240

Wplan_240_1

240


PP01_1_240, PP01_2_240, PP01_3_240, PP01_4_240

Wplan_240_2

240


PP01_5_240, PP01_3_240, PP01_4_240

266


Table 10.34 Possible assignments of machining workingsteps for product code 240 id workingstep id machine id pallet ws01

GP, R1, R2, R3, R4, R5

PP01_4_240, PP01_7_240, PP01_8_240, PP01_10_240, PP01_11_240

ws02

GP, R1, R2, R3, R4, R5

PP01_4_240, PP01_7_240, PP01_8_240, PP01_10_240, PP01_11_240

ws03

GP, D1, D2, D3, D4, D5

PP01_2_240, PP01_5_240, PP01_8_240, PP01_9_240, PP01_10_240

ws04

GP, R1, R2, R3, R4, R5, D1, D2, D3, D4, D5

PP01_1_240, PP01_5_240, PP01_6_240, PP01_7_240, PP01_8_240

ws05

GP, R1, R2, R3, R4, R5, D1, D2, D3, D4, D5

PP01_1_240, PP01_5_240, PP01_6_240, PP01_7_240, PP01_8_240

ws06

GP, D1, D2, D3, D4, D5

PP01_1_240, PP01_5_240, PP01_6_240, PP01_7_240, PP01_8_240

ws07

GP, R1, R2, R3, R4, R5, D1, D2, D3, D4, D5

PP01_4_240, PP01_7_240, PP01_8_240, PP01_10_240, PP01_11_240

ws08

GP, R1, R2, R3, R4, R5, D1, D2, D3, D4, D5

PP01_3_240, PP01_6_240, PP01_8_240, PP01_9_240, PP01_11_240

ws09

GP

PP01_4_240, PP01_7_240, PP01_8_240, PP01_10_240, PP01_11_240

ws10

GP

PP01_4_240, PP01_7_240, PP01_8_240, PP01_10_240, PP01_11_240

ws11

GP, R1, R2, R3, R4, R5, D1, D2, D3, D4, D5

PP01_2_240, PP01_5_240, PP01_8_240, PP01_9_240, PP01_10_240

ws12

GP

PP01_1_240, PP01_5_240, PP01_6_240, PP01_7_240, PP01_8_240

10.4 Robustness of FFMS Solutions The main characteristics of the FFMS configurations have already been studied in Chap. 7 (see Sect. 7.9). It was shown that an FFMS can offer economic advantages if the database of selectable resources is quite heterogeneous. In particular, the profitability of an FFMS compared to a traditional FMS has been investigated for different aggregate demand levels, different part mixes and different types of dedicated machines. The experiments have been carried out considering a deterministic and static production environment, thus simplifying the manufacturing system design model. However, since the preface of this book it was highlighted that the changes affecting the production environment can have an important effect on the design of the most effective manufacturing system solution. Therefore in this section it will be studied if the profitability of an FFMS is affected by the variability of the production problem.

10

Testing

267

10.4.1 Design of Experiment The FFMS design approach presented in Chap. 7 (see Sect. 7.4) has been developed to cope with both the dynamic and stochastic characteristics of production problems. The dynamic issues have been addressed adopting a multi-stage approach that considers a multi-period horizon (see Sect. 7.4; Ahmed et al. 2003); the stochastic issues have been faced by modeling the production problem evolution with a scenario tree (see Chap. 5 and Sect. 7.3). The FFMS design problem is addressed by means of the FFMS design model formulated in Sect. 7.6. In this chapter the considered planning horizon consists of two planning periods (these planning periods can be the aggregation of shorter sub-periods). Since the planning horizon consists of only two periods, the multi-stage stochastic model boils down to a two-stage stochastic instance of the problem (Birge and Louveaux 1997). The first planning period must be addressed with the first stage decisions, while the potential changes happening in the second planning period of the planning horizon can be faced with recourse actions, i.e. system reconfigurations. Chapter 7 has shown that an FFMS solution can offer significant economic benefits compared to a traditional FMS. However, the uncertainty about the future could jeopardize the profitability of an FFMS, because focusing the flexibility reduces the ability of the system to cope with changes in the production problem. To study how an FFMS solution behaves when the production problem is affected by variability, it is necessary to define the scenarios that could happen during the future planning periods; in this case the scenarios are associated with the second period of the planning horizon. The scenarios model the evolution of the production problem and it is therefore important to characterize the changes that could take place. The following issues have been considered to define the types of change:

The changes of the aggregate demand should be modeled. Herein, the expression ‘‘aggregate demand’’ is always referred to the total amount of cutting time that is required to process all the demanded workpieces. In this way it is possible to precisely express the system capacity needed by the production problem, since different workpiece types could require a different amount of cutting time. Product changes that are related to the characteristics (e.g. machining features) of the demanded workpiece types should be modeled. The changes should be modeled using the information that can be reasonably provided by a system user to a machine tool builder. In real industrial cases it is not always possible to precisely model the evolution of the production problems. Therefore, the evolution scenarios should be defined by elaborating general (and sometimes imprecise) information provided by the system user. The attention should be focused on the key issues that could have an impact on the profitability of an FFMS. Indeed, the customization of the system

268


resources on the characteristics of the production problem could have negative side-effects if these characteristics frequently change. Taking into consideration the previous points, the evolution of the production problem can be characterized by answering to the following questions:

Which is the aggregate demand level (i.e. saturation of the machines) in the

first planning period? Will the expected aggregate demand remain constant? Which is the level of uncertainty related to the future aggregate demand? Will the ratio among the operation types remain constant? Which is the level of uncertainty related to the future ratio among the operation types ?

The answers to these questions can have a relevant impact on the optimal system configuration that should be designed. Indeed, if the aggregate demand is constant during the planning horizon and the future demand is endowed with a low variability, then only minor reconfigurations will be needed. If the ratio among the operation types remains constant, then it is possible to highly customize the system resources on the production problem. If the fraction of cutting time that cannot be executed on dedicated machines is small, then it should be easier to focus the flexibility of the system. The answers to the previous questions can be formalized by proposing five factors that characterize the evolution of the production problem. These factors will assume a different value according to the given answers. The following factors have been defined:

Aggregate demand during the first planning period (Dlev). Change of the aggregate demand (Dch). The expected value of the aggregate demand during the second planning period is compared to the aggregate demand during the first planning period. Variability of the aggregate demand during the second planning period (Dvar). Change of the fraction of cutting time required by operation types that cannot be executed on dedicated machines (Fch). The expected value of this fraction during the second planning period is compared to the fraction during the first planning period. Variability of the fraction of cutting time required by operation types that cannot be executed on dedicated machines during the second planning period (Fvar). Two values have been considered for each factor: ‘‘Level 0’’ is associated with a low value of the factor, while ‘‘Level 1’’ to a high value. The factors and the values for each level are reported in Table 10.35. To study the influence of each factor on the profitability of an FFMS, all the possible combinations of the values of the factors have been considered, thus leading to 32 experimental conditions to be tested.

10

Testing

269

Table 10.35 Factors and levels Factor N. Level 0 Levels Dlev

2

Dch

2

Dvar

2

Fch

2

Fvar

2

Low aggregate demand in the first planning period No change compared to the first planning period (+0%) Low variability around the expected value. There are three possible outcomes (-10%, 0%, +10%) compared to the expected value No change compared to the first planning period (+0%)

Low variability around the expected value. There are three possible outcomes (10%, 0%, +10%) compared to the expected value

Level 1 High aggregate demand in the first planning period Increase of cutting time compared to the first planning period (+ 25%) High variability compared to the expected value. There are three possible outcomes (25%, 0%, +25%) compared to the expected value. Increase of cutting time required by operation types that cannot be executed on dedicated machines (+25%) High variability around the expected value. There are three possible outcomes (30%, 0%, +30%) compared to the expected value

Two stochastic parameters are influenced by the levels of the factors. The first three factors determine the distribution of the future aggregate demand, while the forth and fifth factors determine the distribution of the fraction of cutting time required by operation types that cannot be executed on dedicated machines. For the sake of simplicity, the distributions of the stochastic parameters have been discretized over three values (Table 10.35). The hypothesis is made that these outcomes have the same realization probability. For each experimental condition it is possible to develop a scenario tree that models both the evolution and the uncertainty. Assuming that there is no correlation between the distributions of the two stochastic parameters, nine scenarios result from the combination of the outcomes. These scenario trees can be generated by means of a tool as presented in Sect. 5.5. In Chap. 7 it was already demonstrated that the level of aggregate demand influences the profitability of FFMSs, because it has an impact on the size of the system and on the number of resources that are required. It was decided to address production problems requiring a small size system as initial configuration, because this type of systems are more common in industrial cases (see Sect. 7.9.2). Therefore, both levels of the Dlev factor require an initial system configuration with two machines for the FMS solution. A low aggregate demand in the first planning period means that the FMS solution is characterized by a low saturation of the machines (65%), while a high aggregate demand leads to a higher saturation (90%). The fraction of cutting time that cannot be processed on dedicated machines has been set equal to 0.28.

270


Three test cases have been designed to replicate the Design of Experiment (DoE) and to study which is the impact of the factors on the problem of manufacturing system design. These test cases (named TC1, TC2 and TC3) have been defined by varying the conditions of the production problem during the first planning period and in particular:

the set of workpiece types composing the part family; the ratio between the cutting time required by roughing and drilling operations.

10.4.2 FFMS Profitability In Chap. 7 the main response of the testing experiments was the profitability of the FFMS solution that was represented by the performance indicator Dcost% (10.1), i.e. the percentage difference between the FMS cost and FFMS cost when the planning horizon consists of only one period. In this section, the performance indicator must be slightly modified to take into consideration also the uncertainty associated with future planning periods. Therefore, the main response of the testing experiments is the expected profitability of the FFMS solution that is represented by the performance indicator EDcost% (10.2), i.e. the percentage difference between the expected cost of an FMS and the expected cost of an FFMS over the planning horizon. The cost of the system is given by the sum of the initial configuration costs along with the reconfiguration costs that are weighted according to the realization probability of the scenarios. The definition of the performance indicators related to the cost of the system solution are reported in Table 10.36.

Table 10.36 Definition of the performance indicators Performance Definition indicator FMS1 FFMS1 FMS2s FFMS2s Dcost%

EDcost%

Cost of the FMS solution when the planning horizon consists of one period (single-stage approach) Cost of the FFMS solution when the planning horizon consists of one period (single-stage approach) Expected Cost of the FMS solution when the planning horizon consists of two periods (two-stage stochastic approach) Expected Cost of the FFMS solution when the planning horizon consists of two periods (two-stage stochastic approach) Percentage difference between the FMS cost (FMS1) and FFMS cost (FFMS1) when the planning horizon consists of one period (singlestage approach) Percentage difference between the expected cost of an FMS (FMS2s) and the expected cost of an FFMS (FFMS2s)

10

Testing

271

Dcost% ¼

EDcost% ¼

FMS1 FFMS1 100 FMS1

(10:1)

FMS2s FFMS2s 100 FMS2s

(10:2)

Since there are 32 experimental conditions and three test cases, it was necessary to obtain 96 FFMS solutions and 96 FMS solutions addressing all the production problems in order to calculate the performance indicators Dcost% and EDcost%. As an example the results of Test Case n.1 are reported in Table 10.37. Table 10.37 Dcost% and EDcost% for Test Case n.1 ExpCond Dlev Dch Dvar Fch Fvar

Test Case

cost%

Ecost%

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1

13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 13.17 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55 17.55

9.66 15.38 14.66 19.81 15.58 20.69 20.72 15.36 10.01 9.20 13.88 11.51 5.56 9.20 10.39 4.08 13.48 13.85 16.18 16.57 2.03 2.52 5.56 5.96 11.32 11.10 14.37 14.81 17.50 17.44 17.44 17.44

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0

1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

272


The impact of the five factors (i.e. Dlev, Dch, Dvar, Fch and Fvar) can be evaluated by means of the dotplots in Fig. 10.15, where the results of the three test cases have been aggregated. The impact of the five factors on the mean value of EDcost% can be better understood by analyzing also the main effects plots (Fig. 10.16). These graphs allow to compare the mean value of EDcost% that is obtained in correspondence

(a)

(b)

(c)

(d)

(e)

(f)

Fig. 10.15 Dotplots of EDcost% against (a) Dlev, (b) Dch, (c) Dvar, (d) Fch, (e) Fvar and (f) Test Cases

10

Testing

273

Fig. 10.16 Main effects plots for factors Dlev, Dch, Dvar, Fch and Fvar

of the different levels of each factor. In this way it is possible to check which is the effect on the value of EDcost% by changing the level of a factor. The graphs in Figs. 10.15 and 10.16 show that the FFMS solutions are pretty robust towards changes in the aggregate demand. If the initial aggregate demand is high (i.e. factor Dlev is at level 1) or if the future aggregate demand tends to grow (i.e. factor Dch is at level 1), then FFMS profitability grows as well. Indeed, a higher aggregate demand enables to better focus the flexibility of the system, as it has already been proved in Chap. 7 (see Sect. 7.9.2). The variability of the future aggregate demand does not have a negative influence on the profitability of an FFMS, since the mean value of EDcost% increases when the factor Dvar is at level 1, i.e. when there is a high variability of the future aggregate demand. If the future aggregate demand variability is low, then only minor reconfigurations in the systems will be required and the expected profitability of the FFMS (EDcost%) will not be much different from the profitability of the initial system configuration. On the other hand, if the variability is high, there will be future scenarios with very low aggregate demand and other scenarios very high aggregate demand. In the scenarios with low demand only minor reconfigurations will be needed, thus confirming again the FFMS profitability that is given by the initial system configuration. In the scenarios with a high demand compared to the first planning period, it will be probably necessary to execute major reconfigurations by acquiring new resources; in this case the size of the system grows and it becomes easier to focus the system flexibility. Therefore there will be some scenarios with a higher FFMS profitability and the value of EDcost% will increase compared to the cases with low variability of the future aggregate demand. Moreover, it can be noted the effect of the factor Dvar on the dispersion of EDcost%. If there is a higher variability of the aggregate demand (i.e. Dvar at

274


level 1), then there is a lower variance of the expected FFMS profitability, because favorable and non favorable extreme cases will be balanced when calculating the expected value. On the other hand, if there is a low variability of the future aggregate demand (i.e. Dvar at level 0), then there is a higher variance of the expected FFMS profitability because it relies mainly on the initial system configuration which can be highly or poorly focused, according to the aggregate demand and on the technological characteristics of the test case (as already shown in Chap. 7 and in this section). The reduction of the EDcost% variance when the future production problem is subject to high variability can be statistically checked through a F-Test and a Levene’s Test. Both tests confirm that there is a significant difference among the variances of EDcost% (Fig. 10.17). The technological changes of the part family have a greater impact on the FFMS profitability than the changes in the aggregate demand. Indeed, the factor Fch influences significantly the mean value of EDcost% (Fig. 10.16) and the expected FFMS profitability is worse when there are changes of high magnitude (i.e. when the factor Fch is at level 1). On the other hand, the factor Fvar has a small impact on the performance indicator EDcost%. If the technological requirements of the part family change in the future, then it is more difficult to focus the system flexibility in a stable way because the optimal set of resource types is not constant. It is possible to cope with this problem in two ways: 1. by acquiring more dedicated machines that will have a low saturation, thus highly focusing the flexibility of the system; 2. by acquiring general purpose machines instead of dedicated machines, thus reducing the customization of the system.

Fig. 10.17 Test for equal variances

10

Testing

275

In both cases the FFMS solution becomes more expensive, leading to a lower expected profitability of the FFMSs. For instance, considering a sample production problem, the optimal system solution could consist of one general purpose machine and one roughing machine in the first planning period. If the factor Fch is at level 1, the amount of finishing operations increases significantly and it could happen that the only general purpose machine is saturated in some scenarios, thus risking not to satisfy the demand. To cope with the problem it is possible to acquire also a drilling machine to reduce the saturation of the general purpose machine by moving some of the drilling&finishing operations. Otherwise, it could be cost effective to change the initial system solution by acquiring two general purpose machines and no dedicated machine. The best solution depends on the cost of the resources and on the realization probability of the scenarios. The impact of the changes in the production problem on the profitability of an FFMS can be better understood by comparing the FFMS profitability of the solutions given by the two-stage stochastic design model (EDcost%) and by the single-stage design model (Dcost%). Moreover, new performance indicators can be calculated to analyze the effect of the changes on the expected cost of the system solutions: EccFMS% (10.3) and EccFFMS% (10.4). The definitions of these performance indicators are reported in Table 10.38.

Table 10.38 Definition of the performance indicators Performance Definition indicator EccFMS%

EccFFMS%

Expected Cost of the production problem changes for the FMS solution. It is the percentage difference between the expected cost of an FMS (FMS2s) when the planning horizon consists of two periods and the cost of an FMS (FMS1) when the planning horizon consists of one period Expected Cost of the production problem changes for the FFMS solution. It is the percentage difference between the expected cost of an FFMS (FFMS2s) when the planning horizon consists of two periods and the cost of an FFMS (FFMS1) when the planning horizon consists of one period

FMS2s FMS1 100 FMS1

(10:3)

FFMS2s FFMS1 100 FFMS1

(10:4)

EccFMS% ¼

EccFFMS% ¼

276


Fig. 10.18 FFMS profitability with a singleperiod horizon (Dcost%) and a two-period horizon (EDcost%)

Figure 10.18 shows the comparison of the FFMS profitability when the production problem is static and deterministic (Dcost%) and when it is affected by changes and variability (EDcost%). Changes and variability of the production problem increase the variability of the FFMS profitability which is usually lower than in the static case. Given the discrete nature of the resources, Dcost% is concentrated around two values, while EDcost% ranges from 0 to 20.72, as reported in Table 10.39.

Table 10.39 Descriptive statistics of Dcost% and EDcost% Performance Sample Mean Standard Minimum indicator size Deviation Dcost% EDcost%

96 96

15.253 11.941

2.189 5.419

13.03 0

Median

Maximum

15.27 12.6

17.55 20.72

The cost of the changes in the production problem are shown in Fig. 10.19 by means of boxplot graphs both for EccFMS% and EccFFMS%. It can be noted that EccFFMS% has a mean value slightly higher than EccFMS%. This happens because the changes of the production problem have a larger effect on the FFMS solution, since the flexibility cannot be highly focused in all the

Fig. 10.19 Expected cost of changes for FMS and FFMS solutions

10

Testing

277

experimental conditions. However, the variability of the change cost is lower for the FFMS solution. Indeed, in the FMS solutions there are extreme cases where the change of the production problem has no effect thanks to the system flexibility, but also other extreme cases with a high cost of the changes given by the relevant cost of a general purpose machine and by the discrete nature of the resources. The results presented in this sub-section have shown that an FFMS offers a good economic performance when the aggregate demand undergoes changes and is subject to variability in the mid- and long-term horizon. On the other hand, changes in the production problem related to the type of operations that must be executed risk to reduce the profitability of an FFMS solution. In Fig. 10.18 it can be seen that in some cases the expected profitability of the FFMS is very low, and in a few extreme cases it is equal to zero. All these cases are related to experimental conditions where the factor Fch is set at level 1, thus meaning that the chance to focus the system flexibility will be reduced in the future. In these cases the FFMS solution is not able to offer any advantage compared to a traditional FMS solution.

10.4.3 Initial System Configurations The future changes of the production problem have an impact not only on the future reconfigurations, but also on the initial system configuration. Adopting an FFMS design model it is possible to take the decision about the right moment when to acquire system resources. If some changes are expected, it can be effective not to focus the flexibility of the system at the maximum level during the initial system configuration. New performance indicators are defined in Table 10.40: DinitFMS% (10.5), DinitFFMS% (10.6) and Dinitcost% (10.7) DinitFMS% ¼

FMS2sI FMS1 100 FMS1

(10:5)

Table 10.40 Definition of the performance indicators Performance Definition indicator FMS2sI FFMS2sI DinitFMS%

DinitFFMS%

Dinitcost%

Cost of the initial system configuration of the FMS solution (two-stage stochastic approach) Cost of the initial system configuration of the FFMS solution (two-stage stochastic approach) Percentage difference between the cost of the initial FMS configuration obtained with the single stage approach (FMS1) and with the twostage stochastic approach (FMS2sI) Percentage difference between the cost of the initial FFMS configuration obtained with the single stage approach (FFMS1) and with the twostage stochastic approach (FFMS2sI) Percentage difference between the cost of the initial FFMS configuration (FFMS2sI) and the cost of the initial FMS configuration (FMS2sI), both of them obtained with the two-stage stochastic approach

278


DinitFFMS% ¼

FFMS2sI FFMS1 100 FFMS1

initcost% ¼

FFMS2sI FMS2sI 100 FMS2sI

(10:6)

(10:7)

Fig. 10.20 Boxplots of DinitFMS% and DinitFFMS%

The testing results in Fig. 10.20 show that the initial configuration of the FMS solution is not affected by the changeability of the production problem. Only the resources that are strictly necessary are acquired and, if necessary, future reconfigurations will be designed adding one or more general purpose machines. On the other hand, the cost of the initial FFMS configuration increases when changes can happen in the production problem. Indeed, the FFMS solution becomes more flexible and similar to an FMS and in some extreme cases it becomes even equal to an FMS. This phenomenon happens when the most critical changes characterize the production problem, in particular when the factors Fch, Dch and Dlev are at level 1. The experimental conditions with DinitFFMS% greater than zero are reported in Table 10.41. Even if the changes in the production problem could increase the initial investment required by an FFMS, the cost is still lower than the initial cost of an FMS. The values of the performance indicator Dinitcost% are shown in Fig. 10.21. The cost reduction of the initial system configuration ranges from 0% to 17.55%, while the expected FFMS profitability ranges from 0 to 20.72%. There are 6 cases where Dinitcost% takes value equal to zero. This happens only when there are changes in the technological characteristics of the future production problem, i.e. the factor Fch and/or the factor Fvar are set to level 1.

10

Testing

279

Table 10.41 Experimental conditions with DinitFFMS% greater than zero Exp Dlev Dch Dvar Fch Fvar Test Ecost% cost% initFMS% initFFMS% Cond Case 21 22 22 14 14 13 13 22 18 24 24 23 23 26 27 28 28 19 19 20 20 26 3 3

0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1

1 1 1 0 0 0 0 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 1 1

0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1

Fig. 10.21 Dotplot of Dinitcost%

1 1 1 1 1 1 1 1 1 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0

1 0 0 0 0 1 1 0 0 0 0 1 1 0 1 0 0 1 1 0 0 0 1 1

TC2 TC2 TC3 TC2 TC3 TC2 TC3 TC1 TC1 TC2 TC3 TC2 TC3 TC2 TC2 TC2 TC3 TC2 TC3 TC2 TC3 TC1 TC2 TC3

0.00 0.00 0.00 1.68 1.68 3.23 3.23 2.52 13.85 5.13 5.13 6.60 6.60 10.40 13.03 13.03 13.03 13.83 13.83 16.16 16.16 11.10 15.02 15.02

17.37 17.37 17.37 13.03 13.03 13.03 13.03 17.55 17.55 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.37 17.55 13.03 13.03

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00

21.02 21.02 21.02 14.98 14.98 14.98 14.98 5.32 5.32 5.26 5.26 5.26 5.26 5.26 5.26 5.26 5.26 5.26 5.26 5.26 5.26 3.99 3.75 3.75

280


10.5 Value of the Stochastic Solution The whole manufacturing system design architecture introduced in Chap. 1 and then detailed in Chaps. 5, 6, 7, 8 and 9 has been developed assuming the importance of taking into consideration the uncertainty affecting the design problem. Therefore, Chap. 5 has addressed the problem of scenario tree generation to model the possible evolutions of the production problem, while Chaps. 7 and 8 have proposed methodologies based on the exploitation of such scenario trees. The aim of this section is to investigate whether it is really worth to invest in modeling the stochastic aspects of the system design problem. In particular, is it possible to quantify the advantage coming from this type of modeling? To answer this question, an extension of the testing experiments presented in Sect. 10.4 has been developed and will be described in this section. The advantage given by a stochastic approach can be measured by means of the parameter named Value of the Stochastic Solution (VSS). This parameter represents the difference between the performance of a stochastic model and the performance of a deterministic model that considers the expectation of the stochastic outcomes (Birge and Louveaux 1997; Terkaj and Tolio 2006; Tolio and Urgo 2007). To compare these models it is necessary to execute the following steps:

The stochastic FFMS design model (see Sect. 7.6) is solved. The value of the resulting objective function corresponds to the expected cost of the system that can be named FFMS2s. The determinist version of the FFMS design model is solved. This version of the model takes as input a scenario tree consisting of only one scenario that is built creating an average scenario node in each time period of the planning horizon. However, the solution of this model is not applicable because the decisions are taken not considering the real scenarios. The first stage solution of the deterministic model is evaluated against the possible scenarios. For each scenario it is necessary to solve an FFMS design problem that is constrained by the decisions already taken in the first stage. The FFMS costs in the different scenarios are weighted according to the probability of the scenarios to calculate the expected cost of the system that can be named FFMS2d. After solving all the FFMS design versions of the problem, it is possible to calculate the performance indicator vssFFMS (10.8) and vssFFMS% (10.9). The definitions of these indicators are reported in Table 10.42. vssFFMS ¼ FFMS2d FFMS2s

vssFFMS% ¼

FFMS2d FFMS2s 100 FFMS2d

(10:8)

(10:9)

10

Testing

281

Table 10.42 Definition of the performance indicators Performance Definition indicator Expected Cost of the FFMS solution when the planning horizon consists of two periods (two-stage stochastic approach) Expected Cost of the FFMS solution when the planning horizon consists of two periods (two-stage deterministic approach) Value of the Stochastic Solution when adopting the two-stage stochastic approach to design an FFMS solution Percentage Value of the Stochastic Solution when adopting the twostage stochastic approach to design an FFMS solution

FFMS2s FFMS2d vssFFMS vssFFMS%

The impact of the changes in the production problem on the Value of the Stochastic Solution has been evaluated considering the Design of Experiments that has been presented in Sect. 10.4.1.

10.5.1 Testing Results Considering five factors with two levels (Dlev, Dch, Dvar, Fch and Fvar) and three replicates (test cases TC1, TC2 and TC3) it was necessary to solve 96 times the stochastic and the deterministic versions of the FFMS design model. The results of the experiments related to Test Case n.1 are reported in Table 10.43 as an example. Table 10.43 vssFFMS% for Test Case n.1 ExpCond Dlev Dch Dvar

Fch

Fvar

Test Case

vssFFMS%

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1

1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1

0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 5.60 4.76 9.67 7.18 2.39 4.76 7.40 2.44 9.24 0.68

1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0

1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1

1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1

282


Table 10.43 (continued) ExpCond Dlev Dch

Dvar

Fch

Fvar

Test Case

vssFFMS%

19 20 21 22 23 24 25 26 27 28 29 30 31 32

1 1 0 0 0 0 1 1 1 1 0 0 0 0

0 0 1 1 0 0 1 1 0 0 1 1 0 0

1 0 1 0 1 0 1 0 1 0 1 0 1 0

TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1 TC1

0.00 0.00 2.03 0.68 0.00 0.00 0.00 2.25 0.00 0.00 0.00 0.00 0.00 0.00

0 0 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 1 0 0 0 0 0 0 0 0

The impact of the five factors defined in Sect. 10.4.1 is analyzed by means of dotplots (Fig. 10.22) and main effect plots (Fig. 10.23). The dotplots graphs (Fig. 10.22) show that vssFFMS% is equal to zero in most of the experiments (58 off 96 cases). However, there are some cases with a relevant vssFFMS% that is close to 10%. The mean value of vssFFMS% is equal to 1.744%. The main effects plots (Fig. 10.23) show that the factors Dlev, Dch, Dvar and Fvar have an impact on the mean value of vssFFMS%. The impact on vssFFMS% is relevant when, given the type of evolution of the production problem, the initial system configuration (i.e. the first stage decisions) plays a crucial role in the performance of the system. When Dlev is at level 1, vssFFMS% is higher because the choice of the resources is more critical, since the resources are more saturated. The decisions in the first stage have a strong impact on the need and magnitude of reconfigurations during the future stages. On the other hand, when Dch is at level 1, vssFFMS% is lower because in the future there will be relevant changes of the demand; therefore reconfigurations will be probably required, thus reducing the importance of the first stage configuration. The value of vssFFMS% grows also when there is high variability of the future production problem, i.e. when Dvar and/or Fvar are at level 1. Indeed, if there is high uncertainty about the future, then it becomes important to adopt a stochastic approach considering the possible scenarios. Figure 10.22 shows also that the variance of VSS% is greater when there is high variability in the future periods (i.e. Dvar and Fvar at level 1), as confirmed by the tests for equal variances reported in Fig. 10.24. This means that a high variability of the future production problem has a twofold effect:

10

Testing

283

(a)

(b)

(c)

(d)

(e)

(f)

Fig. 10.22 Dotplots of vssFFMS% against (a) Dlev, (b) Dch, (c) Dvar, (d) Fch, (e) Fvar and (f) Test Cases

The mean VSS% grows; The variance of VSS% grows and it is more likely to face extreme cases with a high VSS. The differences among the experimental conditions are reduced if the coefficient of variation (CV) is considered, as reported in Table 10.44.

284


Fig. 10.23 Main effects plots for factors Dlev, Dch, Dvar, Fch and Fvar

Fig. 10.24 Test for equal variances

Table 10.44 Descriptive statistics for vssFFMS% Dvar Fvar Mean StDev Minimum Median

Maximum

CV (mean/StDev)

0 0 1 1

4.76 7.4 7.18 9.67

0.49925 0.477959 0.921819 0.731197

0 1 0 1

0.666 1.171 2.311 2.829

1.334 2.45 2.507 3.869

0 0 0 0

0 0 1.54 0.21

10

Testing

285

Table 10.45 FFMS profitability with stochastic and deterministic approach Exp Dlev Dch Dvar Fch Fvar Test Ecost% vssFFMS% Cond Case

Ecost DET%

11 11 11

4.66 5.97 5.97

1 1 1

0 0 0

1 1 1

0 0 0

1 1 1

TC1 TC2 TC3

13.88 14.81 14.81

9.67 9.40 9.40

Table 10.44 reports that the largest vssFFMS% is equal to 9.67%. This means that a stochastic model to design an FFMS can help to avoid wrong decisions that could risk to jeopardize the profitability provided by focusing the flexibility. Indeed the profitability of the FFMS could be strongly reduced (or even become negative in extreme cases) if a deterministic model is adopted. Three examples of this phenomenon are reported in Table 10.45. It can be noted that a stochastic approach gives a profitability (EDcost%) greater that 13%, while adopting a deterministic approach the profitability (EDcostDET%) is severely reduced to less than 6%. Finally, it can be useful to study which is the impact of the stochastic approach on the cost of the initial FFMS configuration. A new performance indicator vssFFMSinit% (10.10) is defined as the percentage difference between the cost of the initial FFMS configuration obtained with the stochastic approach (FFMS2sI) and with the deterministic approach (FFMS2dI). vssFFMSinit% ¼

FFMS2dI FFMS2sI 100 FFMS2dI

(10:10)

Figure 10.25 shows the dotplot graph of vssFFMSinit%. In most of the experiments there is no difference between the initial solution of the stochastic and deterministic approach, since in 58 off 96 cases the Value of the Stochastic

Fig. 10.25 Dotplot of vssFFMSinit%

286


Solution is equal to zero. In 11off 96 cases the stochastic approach leads to an initial configuration that is more flexible and expensive; the additional investment (maximum 5.26%) is necessary to better cope with the future changes in the production problems and avoid unnecessary reconfigurations. However, it can be noted that in 27 off 96 cases the stochastic approach allows to reduce the cost of the initial FFMS configuration. The results presented in this section prove that the design of an FFMS requires a stochastic approach in order to carefully evaluate how and when it is possible to focus the flexibility of the system. Indeed, the choice of the methodology to design an FFMS is strongly related to the nature of the system. Since the aim of an FFMS is to focus the system flexibility, it is necessary to adopt a methodology that allows to evaluate which is the amount of flexibility that is required by the present and future production problems. If this evaluation is not carried out, then there is a risk to design poor FFMS solutions that will have a negative economic impact for the system users. On the other hand, the design of an FMS usually does not require a stochastic approach because it is more difficult to take a wrong decision about the type of machine, since only flexible machines can be purchased. Indeed, in the experiments carried out regarding FMS design the VSS% has resulted to be equal to zero in all the experimental conditions since only one type of flexible machine was available.

10.6 Performance Evaluation Through Simulation The FFMS design model introduced in Chap. 7 has been developed considering the following approximations:

failures of the machines have been modeled by introducing an availability

coefficient, but the impact could be more relevant if a critical machine fails especially if the FFMS architecture is particularly rigid; mission time of carriers cannot be properly estimated ex-ante; the dynamics related to the management of the pallets (e.g. queues, waiting time in the buffer zone) have not been considered; the management of the cutting tools is not explicitly considered; the saturation of the machines can be reduced if they have to wait for the tools; some of the machines could be starved if the necessary work in progress or raw pieces are not ready.

Therefore the resulting system solutions need to be dynamically evaluated (Levantesi et al. 2003; Colledani and Tolio 2005). In particular, it is necessary to evaluate if the various approximations lead to acceptable estimates of the system performance or if the FFMS design model is not reliable. The attention is focused on the performance of the pallet carrier and on its saturation. Indeed, in production systems characterized by a hybrid architecture, such as FFMSs, the pallet routing is not completely linear. Herein, the estimation of the carrier saturation is extremely important because:

10

Testing

287

the number of carrier missions depends also on the dynamics of the system (e.g. queues, failures, starvation, blocking, etc.) that are not easy to estimate and that have been considered in the model only through correction parameters; in an FFMS there are more carrier missions than in a traditional FMS because some pallet types can be assigned to more than one machine type. Therefore the carrier could become the bottleneck of the system thus jeopardizing the feasibility of FFMS solutions. The validation of the FFMS performance has been carried out through the simulation technique (Anglani et al. 2002) adopting the methodology presented in Chap. 9. The design of the testing experiments is introduced in the following sub-section.

10.6.1 Design of Experiments The experiments have been designed keeping as a reference the general settings presented in Sect. 10.3 for what regards the part family (see Sect. 10.3.1), the machines (see Sect. 10.3.2) and the process planning (see Sect. 10.3.3). The part mix has been set in order to have a low fraction of operations that can be executed only on general purpose machines (i.e. the fraction of cutting time required by finishing and non-drilling operations), thus helping to focus the flexibility of the system. Four test cases have been defined varying the part family as reported in Table 10.46. Given the part mix of the test cases, different values of aggregate demand have been considered to evaluate if the size of the system has an impact on the estimate of the system performance. Once again the attention has been focused on small size systems. The lowest value of aggregate demand lead to design an FFMS with two machines (one general purpose and one dedicated machine), while the highest value requires a four-machine FFMS. Twenty demand levels have been defined for each test case, thus leading to 4*20 = 80 experiments. The value of the critical parameter ‘‘mean transport time for a mission of the carrier’’ (named tt in Sect. 7.6.1 and Table 7.4) has been estimated through 50 preliminary tests that have been carried out considering different demand Table 10.46 Operation type percentages Test Part family Roughing case operation time percentage

Drilling operation time percentage

Finishing and nondrilling operation time percentage

Perf1 Perf2 Perf3 Perf4

50% 50% 50% 50%

20% 20% 20% 20%

260, 271, 282, 502 240, 260, 280 260, 270, 501 240, 260, 280

50% 50% 50% 50%

288


levels and the operation percentages reported in Table 10.46. The tt parameter has been calculated aiming at minimizing the error in the estimate of the carrier saturation. This parameter is critical because it is used in the capacity constraint associated with the carrier resource (see Sect. 7.6.3 and expression 7.23) The responses of the experiments consist of the estimation and comparison of the following parameters that have been obtained both from the FFMS design model and the simulation model:

carrier saturation; machine saturation.

10.6.2 Testing Results As anticipated, the carrier could be a critical resource in an FFMS configuration. By plotting the values of carrier saturation as a function of the demand level, it is possible to analyze the estimates provided both by the FFMS design model (CsatDES) and by the simulation model (CsatSIM). The results concerning the experiments previously described are illustrated in Figs. 10.26 and 10.27, respectively. The results of the replicates (i.e. test cases) have been grouped for each demand level.

Fig. 10.26 Plot of carrier saturation given by the FFMS design model for each demand level

Fig. 10.27 Plot of carrier saturation given by simulation for each demand level

10

Testing

289

The results show that the level of carrier saturation obtained by the FFMS design model grows almost linearly with the demand level. Moreover, the variability among the different test cases is quite little. Also the saturation given by the simulation grows almost linearly, but it can be noted a higher variability, which is due to the phenomena which have not been considered by the approximations of the design model (e.g. queues, failures, starvation, blocking, etc.). The results can be better analyzed by calculating the error (Cerr) of the carrier saturation given by the design model compared to the output of simulation, which is assumed as the real value. The error is calculated as indicated by equation (10.11): Cerr ¼ CsatSIM CsatDES

(10:11)

The graph of the error Cerr is shown in Fig. 10.28. It can be noted that the value of Cerr slightly grows when the demand value increases. This means that, given the initial estimate of the parameter tt, the design model overestimates the carrier saturation when the aggregate demand is low, while it underestimates the saturation when the aggregate demand is high. Since the saturation strictly depends on the mean time of a carrier mission and on the dynamics of the system, this phenomenon can be explained again by the assumptions that have been adopted by the design model:

The mean mission time has been estimated ex-ante considering a wide range of demand levels. Therefore, the estimate better fits with the demand levels that are in the middle of the considered demand range. However, the mean mission time depends on the size of the system, because, for instance, in a larger system the distance among the resources increases. As the saturation of the resources increases, the impact of the dynamics (e.g. queues) that are not considered by the design model increases. For instance, if the machines and the load/unload stations are more saturated, then the pallet buffer will be used more often, thus increasing the number of

Fig. 10.28 Plot of the error in the estimate of carrier saturation

290


carrier missions. In the design model this type of missions is not considered and therefore the carrier saturation is underestimated. It results that the carrier saturation could be better estimated by enhancing the FFMS design model and considering the influence of the size of the system on the performance of the resources. This could be obtained by defining the following values as variables depending on the size of the system:

the mean mission time (tt); the reduction of the actual carrier capacity that is caused by missions that are not explicitly considered by the FFMS design model, i.e. missions involving the pallet buffer. This aspect is modeled by the coefficient as described in Sect. 7.6.3. Beyond the analysis of the carrier, it is possible to compare also the estimates related to the machines; in particular, the estimates of the busy time are compared. The busy time of a machine is calculated as the fraction of time during which a pallet is loaded on the working position of a machine. A pallet can be characterized by different states when it is in a busy period:

the workpieces on the pallet are machined; the pallet is not being processed by the machine. This could happen because the spindle is waiting for a tool, or the machine has failed, or the pallet is waiting for the carrier after that it has been completely processed. Considering the three different types of machine, the following performance indicators have been calculated for each experiment:

GPerr, i.e. the error in the estimate of the busy time of the general purpose machines made by the FFMS design model compared to the simulation output; Derr, i.e. the error in the estimate of the busy time of the drilling machines made by the FFMS design model compared to the simulation output; Rerr, i.e. the error in the estimate of the busy time of the roughing machines made by the FFMS design model compared to the simulation output. The results for the general purpose, drilling and roughing machine are shown in Figs. 10.29, 10.30 and 10.31 respectively. The error in the estimated saturation

Fig. 10.29 Plot of the percentage error in the estimate of general purpose machine saturation

10

Testing

291

Fig. 10.30 Plot of the percentage error in the estimate of drilling machine saturation

Fig. 10.31 Plot of the percentage error in the estimate of roughing machine saturation

is low for all the machine types (error < 0.1). In particular, the estimate is precise for low-mid levels of aggregate demand. When the production volume grows, the dynamics of the system play a key role, and the machine saturation is underestimated by the FFMS design model. This underestimation is mainly caused by the interaction with the carrier, because when the demand level is high also the number of the carrier missions is high (Figs. 10.26 and 10.27). This means that the pallets on the machines cannot be promptly removed when they are completely processed because of the carrier saturation: therefore the machines risk to be busy even if not working; this phenomenon leads to increase the machine busy time that is underestimated by the FFMS design model. The few cases where the machine saturation is overestimated (i.e. GPerr or Derr or Rerr are greater than zero), correspond to the cases where the system was not able to completely satisfy the demand because of the saturation of at least one resource. For instance, it happens in the case of a pallet type that must be processed both by the general purpose and by a dedicated machine: if the general purpose machine does not succeed in processing the requested volume of pallets, then the dedicated machine will be starved while waiting for pallets coming from the general purpose machine. As a consequence, the saturation of the dedicated machine will be lower than what expected. As anticipated, the estimates of the carrier saturation given by FFMS design model can be improved by updating the mean mission time with the output of

292


Table 10.47 Refining the estimates of carrier saturation Second launch – refining the estimates Test Case Dlev First launch CsatDES CsatSIM Cerr CsatDES CsatSIM Cerr Perf2 Perf2

9 10

0.496 0.471

0.385 0.393

–0.111 –0.078

0.398 0.393

0.385 0.386

–0.013 –0.007

the simulation model. For instance, the problems corresponding to the demand levels n.9 and n.10 of the test case Perf2 have been solved again by the FFMS design model using as input a new value of the parameter tt. The results are reported in Table 10.47. It can be noted that the estimate of the carrier saturation has been improved and the error has been significantly reduced.

10.7 Conclusions The testing experiments presented in this chapter were mainly aimed at studying the profitability of an FFMS in an evolutionary production context and the effectiveness of a stochastic approach when addressing an FFMS design problem. The results have shown that the FFMS solutions are quite robust when facing production problems characterized by changes and variability of the aggregate demand. However, when there are relevant changes in the type of operations to be executed, the profitability of an FFMS solution can be strongly reduced, thus increasing the competitiveness of a traditional FMS. Therefore, during the initial phases of the system design it is necessary to analyze the present and potential future production problems in the most precise way. The stochastic approach to solve the problem of FFMS design has proved to be effective. Even if the mean advantage of the stochastic approach is not high, it gives important benefits in the worst cases by reducing the risk of an FFMS solution. Moreover, it was shown that a stochastic approach can improve the economic performance of an FFMS without requiring a significant increment of the initial system investment cost. The stochastic approach is required to solve the FFMS design problem because the flexibility can be focused only after a careful evaluation of the possible evolutions of the production problem. Indeed, if the flexibility is not focused (e.g. like in an FMS), then the contribution of a stochastic model is null. Therefore, an FMS copes with the evolution of the production problem through the flexibility of the system, while an FFMS copes with the evolution of the production problem by means of the design methodology and of the focused flexibility of the system. Acknowledgments The authors would like to thank the companies Ferraioli & C. S.r.l., IMAS Transfer S.p.A., MCM S.p.A., Nuova Meccanica S.p.A. for their valuable help in characterizing the industrial cases presented in this chapter. The research has been partially funded by

10

Testing

293

the MUR (Italian Ministry for University and Research) under the PRIN project ‘‘Methodologies and tools for the configuration of production systems with focused flexibility’’, contract code: 2005097985.

References Ahmed S, King A, Parija G (2003) A multi-stage stochastic integer programming approach for capacity expansion under uncertainty. J Global Optimiz 26:3–24 Anglani A, Grieco A, Pacella M, Tolio T (2002) Object-oriented modeling and simulation of flexible manufacturing systems: a rule-based procedure. Simul Model Prac Theory 10(3):209–234 Birge JR, Louveaux FV (1997) Introduction to stochastic programming. Springer, London Cantamessa M, Fichera S, Grieco A, Perrone G, Tolio T (2007) Methodologies and tools to design production systems with focused flexibility. Proceedings of the 4th International Conference on Digital Enterprise Technology, Bath, UK, 19–21 September, pp 627–636 Colledani M, Tolio T (2005) A decomposition method to support the configuration / reconfiguration of production systems. Ann CIRP 54(1):441–444 Contini P, Tolio T (2004) Computer aided setup planning for machining centers configuration. Int J Prod Res, 42(17):3473–3491 Levantesi R, Matta A, Tolio T (2003) Performance evaluation of continuous production lines with deterministic processing times, multiple failure modes and finite buffer capacity. Performance Evaluation J 51:247–268 Terkaj W, Tolio T (2006) A Stochastic approach to the FMS loading problem. CIRP J Manuf Syst 35:481–490 Tolio T, Urgo M (2007) A rolling horizon approach to plan outsourcing in manufacturing-toorder environments affected by uncertainty. Ann CIRP 56(1):487–490

Index

A AMSs, see Automated Manufacturing System, AMSs Automated Manufacturing System, AMSs, 66, 139, 141, 149

B Basic flexibility dimensions, 39, 47, 48, 48t, 50, 54, 145, 159 form, 47, 54 levels, 48, 49, 49t, 50, 144–145 Bid generation model, FFMSs, 170–175 decision variables, 172 notation and parameters, 171–172 objective function and constraints, 172–175 Bill of material, BoM, 94, 98, 99, 106 BoM, see Bill of Material, BoM Business strategy differentiation, 102–104 diversification, 104–105 focalization, 99–102

C CAFD, see Computer Aided Fixture Design, CAFD CAPP, see Computer Aided Process Planning, CAPP CNC, see Computer numerical control, CNC Compound flexibility form, 47, 50, 54 Computer Aided Fixture Design, CAFD, 116 Computer Aided Process Planning, CAPP, 114–116 Computer numerical control, CNC, 23, 28, 66, 92, 118, 119, 120, 134, 139, 141, 234

D Data Flow Diagram, DFD, 67 DCF, see Discounted Cash Flow, DCF Decision support, 65, 67, 106, 107, 139, 140 Decision tree, 146–149 representation, 143f, 144f, 165f Dedicated machine, 5, 88, 150, 175–180, 182–187, 234–237, 240, 263, 266, 268, 274, 275, 287, 291 Dedicated Manufacturing Systems, DMSs, 2, 5, 88 Design of Experiment, DoE, 140, 267–270, 281, 287–288 Design of focused flexibility manufacturing systems, FFMSs bid generation model, 170–175 decision variables, 172 notation and parameters, 171–172 objective function and constraints, 172–175 FFMS design models, 153–154 literature, 139–141 multi-stage stochastic FFMS design model, 154–163 decision variables, 157–158 notation and parameters, 154–157 objective function/constraints, 159–163 open research issues, 188 problem statement, 141–142 modeling of production problems, 142–144 system design approach, 144–153 assumptions, 149–151 input, 151–152 output, 152–153 stochastic programming, 146–149 testing profitability of FFMS solutions, 178–187

295

296 Design of focused flexibility manufacturing systems, FFMSs (cont.) test case, 177–178 total cost stochastic model, 163–170 assumptions, 165–166 decision variables, 167 notation and parameters, 166–167 objective function and constraints, 167–170 DFD, see Data Flow Diagram, DFD Differentiation, business strategy, 102–104 Discounted Cash Flow, DCF, 46, 140 Diversification, business strategy, 104–105 DMSs, see Dedicated Manufacturing Systems, DMSs DoE, see Design of Experiment, DoE

E Express-G, 67

F FFMSs, see Focused flexibility manufacturing systems, FFMSs FIFO, see First In First Out, FIFO First In First Out, FIFO, 230, 231 Flexible Manufacturing Systems, FMS, 3, 5–7, 12–16, 19, 23, 24, 25, 47, 85, 88, 92, 176, 178, 179, 182–187, 192, 220, 224, 232, 235, 263, 266–279, 284, 286–292 FMS, see Flexible Manufacturing Systems, FMS Focalization, business strategy, 99–102 Focused flexibility, 6, 7, 10, 11, 20, 21, 23, 29, 58, 94, 188, 217, 221 concept, 13, 15 Focused flexibility manufacturing systems, FFMSs, 1, 3, 5, 6–7, 8–16, 23, 24, 29, 41, 47, 68, 88, 92, 137–188, 240, 266–279, 280–285, 286–292 design activities, 11f design models, 153–154

G GA, see Genetic Algorithm, GA Genetic Algorithm, GA, 140

H Hyperplane, 68, 75, 152, 201, 202

Index I IDEFO diagram, 10f A1 plan system capacity, 11f A2 design systems, 12f FFMS design activities, 11f Information/results, numerical examples, 109t Inputs and outputs sequential model, 200f static model, 199f

L LCA, see Life-Cycle Analysis, LCA Life-Cycle Analysis, LCA, 65 Load/Unload, LU, 24, 56, 77, 163, 224, 229, 234, 289 LU, see Load/Unload, LU LU station, 83, 223, 224, 225, 227, 228, 232, 233, 234

M Machine tool builder, 6, 8, 9, 10, 12, 15, 67, 74, 113, 114, 138, 139, 141, 142, 154, 170–175, 192, 195, 198, 206–208, 267 Machining features, 68, 70, 72t, 72f, 79, 113, 115, 116, 117, 120, 124 product analysis, 240–261, 262–279, 280–285, 286–291, 292–293 Machining operations, 69, 78, 78t, 117, 122, 128, 231 product analysis, 248, 254, 255, 260 Machining tool, 55–58, 75, 88, 92, 115–117, 119, 121, 122, 125, 128, 131, 135, 140, 150, 152, 155, 156t, 163, 175–178, 223t, 229, 234, 235, 263–264 Machining workingsteps of, 69, 78, 79t, 117, 120, 122, 124, 151, 152, 156t, 163, 232 product analysis, 249, 250, 255, 256, 257, 261, 266 Manufacturing flexibility, 19 analysis, 42–43 designing in dynamic production contexts comparison of system performance, 16 design of system configurations, 14–15 mapping of requirements on devices, 14 planning system life-cycle, 15 specification of manufacturing strategy, 13

Index empirical research, 21–25 literature review, 41–50 manufacturing flexibility analysis, 42–43 manufacturing flexibility, design of, 45–47 ontology on flexibility, 47–50 real systems, analysis of, 55–58 state of the art analysis, 50–54 taxonomies/conceptual frameworks, 43–45 Manufacturing strategy, MS, 3, 6, 10, 11, 13, 64, 87–110, 144 differentiation, business strategy, 102–104 dimensions, 92 diversification, business strategy, 104–105 focalization, business strategy, 99–102 production problem analysis for assessing focused flexibility, 87–110 production problem generation-tool, 106–107 production problems generation, 92–99 product life-cycle, 94–95 scenario tree definition, 93 scenario tree generation, 95–99 research background/methodology, 89–92 Mapping Requirements on Devices, MRD, 113–135, 118, 120 hypotheses, 118 procedure, 118–120 Material handling system, MHS, 92 MHS, see Material handling system, MHS Mixed-integer linear programming models, 198 MRD, see Mapping Requirements on Devices, MRD MS, see Manufacturing strategy, MS Multi-stage stochastic FFMS design model, 154–163 decision variables, 157–158 notation and parameters, 154–157 objective function/constraints, 159–163 capacity constraint, 159–161 functionality constraint, 159–160 process constraints, 159–160 N Net Present Value, NPV, 46 NPV, see Net Present Value, NPV O Object Modeling Technique, OMT, 66 OEM, see Original Equipment Manufacturer, OEM

297 OMT, see Object Modeling Technique, OMT Ontology on flexibility, 48f Original Equipment Manufacturer, OEM, 94, 99, 164

P Pallet Configuration, PC for approaching mapping requirements on devices, 113–135 literature background, 114–116 problem statement, 116–118 process configuration, 116–120 proposed procedure, 118–120 setup face configuration, 125–127 setup sequencing, 131–134 tool path and rapid movements, 128 workpiece setup generation, 120–125 procedure, 114, 117, 129–130, 133 Pallet machining, 226f Pallet unloading, 228f PC, see Pallet Configuration, PC Performance evaluation, 6, 10, 64, 69, 75, 78t, 219, 286–292 Performance indicators, definition, 269t, 275t, 277t, 281t Performance Matrix, PM, 198–199, 201–203 Plan System Capacity, 10, 11f, 84t PM, see Performance Matrix, PM Precedence constraints, 250t Process Specification Language, PSL, 66 Production problem modeling, 142–144 analysis and simplification, 144f Product analysis, 240 automotive components, 241–250 railway components, 251–257 hydraulic components, 258–261 Product life-cycle, 94–95, 95f configuration tree, 99f long life-cycle, 94–95 medium life-cycle, 95 short life-cycle, 95 Product-process-system information formalization, 63–85 data formalization for manufacturing system design, 68–70 implementation, 82–84 literature analysis, 64–68 integration, 67–68 production system, 66–67 product and process, 65–66 process, 78–81

298 Product-process-system information formalization, 63–85 (cont.) product, 70–73 production system, 74–78 PSL, see Process Specification Language, PSL

R Real Option Analysis, ROA, 140 Real options, 15, 195, 217 Reconfigurable machine tools, RMT, 88 Reconfigurable Manufacturing Systems, RMS, 4, 5, 6, 47, 88 Rigid transfer lines, RTL, 4 RMS, see Reconfigurable Manufacturing Systems, RMS RMT, see Reconfigurable machine tools, RMT ROA, see Real Option Analysis, ROA RTL, see Rigid transfer lines, RTL

S Scenario data, 157t node, 68, 71, 73t, 143, 155, 173, 198, 207, 280 tree, 15, 71, 73f, 92–108, 149, 154, 196, 199, 267, 269, 280 definition, 93 generation, 95–99, 106–109 representation, 73f, 99f, 100f, 101f, 102f, 103f, 104f, 105f, 143f, 144f, 206f Sequential model, 197, 201, 203, 204–206, 210, 212 decision variables, 205t formation, inputs and outputs, 200f model data, 205 Setup sequencing module, 120, 134 ultimate, 121, 123, 124 Setup face configuration, SFC, 81t, 114, 119–120, 125–127 configuration procedure, 126–127 Setup planning face, 69, 80, 81t, 114, 119, 120, 123, 125, 126, 128–131, 133, 134, 265 module, 119–120 procedure, 114, 120, 121, 123, 125, 128, 129, 133, 134 SFC, see Setup Face Configuration, SFC

Index Simulation model actors of main activities of, 223t description FFMS model management, 232–233 model data, definition, 232 simulation model formalization, 222–224 implementation, 224–233 pallet management policy, 230–231 tool management policy, 231 description of activities of, 224t formalization, 222–224 system layout of the, 229f Small and medium enterprises, SMEs, 191, 193 SMEs, see Small and medium enterprises, SMEs SM, see Switching Costs Matrix, SM SPD, see Standard Placement Direction, SPD Standard Placement Direction, SPD, 121, 122, 124, 132 State Transition Diagram, STD, 67 Static model performance matrix, 201–203 model parameters, 202t switching costs matrix, 203–204 STD, see State Transition Diagram, STD STEP, 66, 67 STEP-NC, 84, 92, 93, 130, 145 Stochastic model, multi-stage, 153, 154, 267 Stochastic Programming, 139, 145 approach, 146–149 model, 153–175 Bid Generation, 170–175 FFMS design, 154–163 Total Cost, 163–170 Switching Costs Matrix, SM, 198–199, 203–204, 210 model parameters, 203t System design approach, FFMSs, 144–153 assumptions, 149–151 input, 151–152 output, 152–153 stochastic programming, 146–149 System Life-Cycle planning, 191–217 life-cycle planning, 193–196 model testing, 206–216 negotiation process, 192 performance matrix, 201–203 sequential model, 197, 201, 203, 204, 210, 212 sets of valuation model, 199

Index static model, 199–204 switching costs matrix, 203–204 valuation model structure, 197–199 System performance simulation and analysis, 219–237 manufacturing systems modeling, 219–221 simulation model building phases, description, 221–233 formalization, 222–224 implementation, 224–231 simulation model validation, 234–237 numerical results, 235–237 System user, 8, 9, 10, 12–16, 29, 74, 138, 141, 153, 170, 171, 173, 174, 191–193, 195, 196, 198, 203, 206, 207, 240, 267

T TAD, see Tool Approach Directions, TAD Testing performance evaluation through simulation, 286–292 product families, description, 240–261 automotive components, 241–250 hydraulic components, 258–261 railway components, 251–257 robustness of FFMS solutions, 266–279 design of experiment, 267–270 FFMS profitability, 270–277 initial system configurations, 277–279 test cases, 262–266 machine types, 263–264 part types, 263 process planning, 264–266 testing experiments, 262 value of the stochastic solution, 280–286

299 Testing, FFMSs profitability of FFMS solutions, 178–187 test case, 177–178 Tool Approach Directions, TAD, 120–121 Tool path computation, 128 generation, 120, 128 Total cost analysis, 153, 163 stochastic model, FFMSs, 163–170 basic assumptions, 165–166 decision variables, 167 notation and parameters, 166–167 objective function and constraints, 167–170

U UML, see Unified Modeling Language, UML Unified Modeling Language, UML, 80, 81, 82, 83f, 84f, 235, 236, 237

V Value of the Stochastic Solution, VSS, 280, 281, 282, 283, 284, 285, 286

W Workpiece, 82, 84, 85t, 85f, 114, 121, 164, 246 analysis, see Product analysis description, 223t, 225t, 228t setup generation, 120–125

Design of Flexible Production Systems

Production Development: Design and Operation of Production Systems

Flexible Software Design: Systems Development for Changing Requirements

Process Oriented Analysis: Design and Optimization of Industrial Production Systems

Nonlinear Dynamics of Production Systems

Thermodynamics of Systems Containing Flexible-Chain Polymers

Thermodynamics of Systems Containing Flexible-Chain Polymers

Thermodynamics of Systems Containing Flexible-Chain Polymers

Aquaculture Production Systems

Production Systems Engineering

Petroleum Production Systems

Petroleum Production Systems

Flexible Production: Restructuring of the International Automobile Industry

Design of Piping Systems

Guitars, Design, Production and Repair

Production Rendering. Design and Implementation

Cooperative Systems Design: Scenario-Based Design of Collaborative Systems

Systems of Production: Markets, organisations and performance

Flexible Query Answering Systems - FQAS 2011

Optimal Design of Queueing Systems

The Engineering Design Of Systems

Design of Hydraulic Control Systems

Optimal design of queueing systems

Design of Industrial Information Systems

Design of Embedded Control Systems

DESIGN OF DEVICES AND SYSTEMS

Flexible AC Transmission Systems: Modelling and Control (Power Systems)

Flexibility Measurement in Production Systems: Handling Uncertainties in Industrial Production

Understanding FACTS: Concepts and Technology of Flexible AC Transmission Systems

Design of Flexible Production Systems

Production Development: Design and Operation of Production Systems

Flexible Software Design: Systems Development for Changing Requirements

Process Oriented Analysis: Design and Optimization of Industrial Production Systems

Nonlinear Dynamics of Production Systems

Thermodynamics of Systems Containing Flexible-Chain Polymers

Thermodynamics of Systems Containing Flexible-Chain Polymers

Thermodynamics of Systems Containing Flexible-Chain Polymers

Aquaculture Production Systems

Production Systems Engineering

Petroleum Production Systems

Petroleum Production Systems

Flexible Production: Restructuring of the International Automobile Industry

Design of Piping Systems

Guitars, Design, Production and Repair

Production Rendering. Design and Implementation

Cooperative Systems Design: Scenario-Based Design of Collaborative Systems

Systems of Production: Markets, organisations and performance

Flexible Query Answering Systems - FQAS 2011

Optimal Design of Queueing Systems

The Engineering Design Of Systems

Design of Hydraulic Control Systems

Optimal design of queueing systems

Design of Industrial Information Systems

Design of Embedded Control Systems

DESIGN OF DEVICES AND SYSTEMS

Flexible AC Transmission Systems: Modelling and Control (Power Systems)

Flexibility Measurement in Production Systems: Handling Uncertainties in Industrial Production

Understanding FACTS: Concepts and Technology of Flexible AC Transmission Systems

Recommend Documents