Damage Mechanics (Dekker Mechanical Engineering)

DK3151_half 4/20/05 2:31 PM Page 1 Damage Mechanics © 2005 by Taylor & Francis Group, LLC DK3151_series.qxd 4/20/05...

Author: George Z. Voyiadjis | Peter I. Kattan

359 downloads 2306 Views 6MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

DK3151_half 4/20/05 2:31 PM Page 1

Damage Mechanics

© 2005 by Taylor & Francis Group, LLC

DK3151_series.qxd

4/20/05

2:26 PM

Page 1

MECHANICAL ENGINEERING A Series of Textbooks and Reference Books Founding Editor L. L. Faulkner Columbus Division, Battelle Memorial Institute and Department of Mechanical Engineering The Ohio State University Columbus, Ohio

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24.

Spring Designer’s Handbook, Harold Carlson Computer-Aided Graphics and Design, Daniel L. Ryan Lubrication Fundamentals, J. George Wills Solar Engineering for Domestic Buildings, William A. Himmelman Applied Engineering Mechanics: Statics and Dynamics, G. Boothroyd and C. Poli Centrifugal Pump Clinic, Igor J. Karassik Computer-Aided Kinetics for Machine Design, Daniel L. Ryan Plastics Products Design Handbook, Part A: Materials and Components; Part B: Processes and Design for Processes, edited by Edward Miller Turbomachinery: Basic Theory and Applications, Earl Logan, Jr. Vibrations of Shells and Plates, Werner Soedel Flat and Corrugated Diaphragm Design Handbook, Mario Di Giovanni Practical Stress Analysis in Engineering Design, Alexander Blake An Introduction to the Design and Behavior of Bolted Joints, John H. Bickford Optimal Engineering Design: Principles and Applications, James N. Siddall Spring Manufacturing Handbook, Harold Carlson Industrial Noise Control: Fundamentals and Applications, edited by Lewis H. Bell Gears and Their Vibration: A Basic Approach to Understanding Gear Noise, J. Derek Smith Chains for Power Transmission and Material Handling: Design a nd Applications Handbook, American Chain Association Corrosion and Corrosion Protection Handbook, edited by Philip A. Schweitzer Gear Drive Systems: Design and Application, Peter Lynwander Controlling In-Plant Airborne Contaminants: Systems Design and Calculations, John D. Constance CAD/CAM Systems Planning and Implementation, Charles S. Knox Probabilistic Engineering Design: Principles and Applications, James N. Siddall Traction Drives: Selection and Application, Frederick W. Heilich III and Eugene E. Shube


DK3151_series.qxd

25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56.

4/20/05

2:26 PM

Page 2

Finite Element Methods: An Introduction, Ronald L. Huston and Chris E. Passerello Mechanical Fastening of Plastics: An Engineering Handbook, Brayton Lincoln, Kenneth J. Gomes, and James F. Braden Lubrication in Practice: Second Edition, edited by W. S. Robertson Principles of Automated Drafting, Daniel L. Ryan Practical Seal Design, edited by Leonard J. Martini Engineering Documentation for CAD/CAM Applications, Charles S. Knox Design Dimensioning with Computer Graphics Applications, Jerome C. Lange Mechanism Analysis: Simplified Graphical and Analytical Techniques, Lyndon O. Barton CAD/CAM Systems: Justification, Implementation, Productivity Measurement, Edward J. Preston, George W. Crawford, and Mark E. Coticchia Steam Plant Calculations Manual, V. Ganapathy Design Assurance for Engineers and Managers, John A. Burgess Heat Transfer Fluids and Systems for Process and Energy Applications, Jasbir Singh Potential Flows: Computer Graphic Solutions, Robert H. Kirchhoff Computer-Aided Graphics and Design: Second Edition, Daniel L. Ryan Electronically Controlled Proportional Valves: Selection and Application, Michael J. Tonyan, edited by Tobi Goldoftas Pressure Gauge Handbook, AMETEK, U.S. Gauge Division, edited by Philip W. Harland Fabric Filtration for Combustion Sources: Fundamentals and Basic Technology, R. P. Donovan Design of Mechanical Joints, Alexander Blake CAD/CAM Dictionary, Edward J. Preston, George W. Crawford, and Mark E. Coticchia Machinery Adhesives for Locking, Retaining, and Sealing, Girard S. Haviland Couplings and Joints: Design, Selection, and Application, Jon R. Mancuso Shaft Alignment Handbook, John Piotrowski BASIC Programs for Steam Plant Engineers: Boilers, Combustion, Fluid Flow, and Heat Transfer, V. Ganapathy Solving Mechanical Design Problems with Computer Graphics, Jerome C. Lange Plastics Gearing: Selection and Application, Clifford E. Adams Clutches and Brakes: Design and Selection, William C. Orthwein Transducers in Mechanical and Electronic Design, Harry L. Trietley Metallurgical Applications of Shock-Wave and High-Strain-Rate Phenomena, edited by Lawrence E. Murr, Karl P. Staudhammer, and Marc A. Meyers Magnesium Products Design, Robert S. Busk How to Integrate CAD/CAM Systems: Management and Technology, William D. Engelke Cam Design and Manufacture: Second Edition; with cam design software for the IBM PC and compatibles, disk included, Preben W. Jensen Solid-State AC Motor Controls: Selection and Application, Sylvester Campbell


DK3151_series.qxd

57. 58. 59. 60. 61. 62. 63. 64. 65. 66. 67. 68. 69. 70. 71. 72. 73. 74. 75. 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. 87.

4/20/05

2:26 PM

Page 3

Fundamentals of Robotics, David D. Ardayfio Belt Selection and Application for Engineers, edited by Wallace D. Erickson Developing Three-Dimensional CAD Software with the IBM PC, C. Stan Wei Organizing Data for CIM Applications, Charles S. Knox, with contributions by Thomas C. Boos, Ross S. Culverhouse, and Paul F. Muchnicki Computer-Aided Simulation in Railway Dynamics, by Rao V. Dukkipati and Joseph R. Amyot Fiber-Reinforced Composites: Materials, Manufacturing, and Design, P. K. Mallick Photoelectric Sensors and Controls: Selection and Application, Scott M. Juds Finite Element Analysis with Personal Computers, Edward R. Champion, Jr. and J. Michael Ensminger Ultrasonics: Fundamentals, Technology, Applications: Second Edition, Revised and Expanded, Dale Ensminger Applied Finite Element Modeling: Practical Problem Solving for Engineers, Jeffrey M. Steele Measurement and Instrumentation in Engineering: Principles and Basic Laboratory Experiments, Francis S. Tse and Ivan E. Morse Centrifugal Pump Clinic: Second Edition, Revised and Expanded, Igor J. Karassik Practical Stress Analysis in Engineering Design: Second Edition, Revised and Expanded, Alexander Blake An Introduction to the Design and Behavior of Bolted Joints: Second Edition, Revised and Expanded, John H. Bickford High Vacuum Technology: A Practical Guide, Marsbed H. Hablanian Pressure Sensors: Selection and Application, Duane Tandeske Zinc Handbook: Properties, Processing, and Use in Design, Frank Porter Thermal Fatigue of Metals, Andrzej Weronski and Tadeusz Hejwowski Classical and Modern Mechanisms for Engineers and Inventors, Preben W. Jensen Handbook of Electronic Package Design, edited by Michael Pecht Shock-Wave and High-Strain-Rate Phenomena in Materials, edited by Marc A. Meyers, Lawrence E. Murr, and Karl P. Staudhammer Industrial Refrigeration: Principles, Design and Applications, P. C. Koelet Applied Combustion, Eugene L. Keating Engine Oils and Automotive Lubrication, edited by Wilfried J. Bartz Mechanism Analysis: Simplified and Graphical Techniques, Second Edition, Revised and Expanded, Lyndon O. Barton Fundamental Fluid Mechanics for the Practicing Engineer, James W. Murdock Fiber-Reinforced Composites: Materials, Manufacturing, and Design, Second Edition, Revised and Expanded, P. K. Mallick Numerical Methods for Engineering Applications, Edward R. Champion, Jr. Turbomachinery: Basic Theory and Applications, Second Edition, Revised and Expanded, Earl Logan, Jr. Vibrations of Shells and Plates: Second Edition, Revised and Expanded, Werner Soedel Steam Plant Calculations Manual: Second Edition, Revised and Expanded, V. Ganapathy


DK3151_series.qxd

88. 89. 90. 91. 92. 93. 94. 95. 96. 97. 98. 99. 100. 101. 102. 103. 104. 105. 106. 107. 108. 109. 110. 111. 112. 113. 114. 115. 116. 117. 118. 119.

4/20/05

2:26 PM

Page 4

Industrial Noise Control: Fundamentals and Applications, Second Edition, Revised and Expanded, Lewis H. Bell and Douglas H. Bell Finite Elements: Their Design and Performance, Richard H. MacNeal Mechanical Properties of Polymers and Composites: Second Edition, Revised and Expanded, Lawrence E. Nielsen and Robert F. Landel Mechanical Wear Prediction and Prevention, Raymond G. Bayer Mechanical Power Transmission Components, edited by David W. South and Jon R. Mancuso Handbook of Turbomachinery, edited by Earl Logan, Jr. Engineering Documentation Control Practices and Procedures, Ray E. Monahan Refractory Linings Thermomechanical Design and Applications, Charles A. Schacht Geometric Dimensioning and Tolerancing: Applications and Techniques for Use in Design, Manufacturing, and Inspection, James D. Meadows An Introduction to the Design and Behavior of Bolted Joints: Third Edition, Revised and Expanded, John H. Bickford Shaft Alignment Handbook: Second Edition, Revised and Expanded, John Piotrowski Computer-Aided Design of Polymer-Matrix Composite Structures, edited by Suong Van Hoa Friction Science and Technology, Peter J. Blau Introduction to Plastics and Composites: Mechanical Properties and Engineering Applications, Edward Miller Practical Fracture Mechanics in Design, Alexander Blake Pump Characteristics and Applications, Michael W. Volk Optical Principles and Technology for Engineers, James E. Stewart Optimizing the Shape of Mechanical Elements and Structures, A. A. Seireg and Jorge Rodriguez Kinematics and Dynamics of Machinery, Vladimír Stejskal and Michael Valásek Shaft Seals for Dynamic Applications, Les Horve Reliability-Based Mechanical Design, edited by Thomas A. Cruse Mechanical Fastening, Joining, and Assembly, James A. Speck Turbomachinery Fluid Dynamics and Heat Transfer, edited by Chunill Hah High-Vacuum Technology: A Practical Guide, Second Edition, Revised and Expanded, Marsbed H. Hablanian Geometric Dimensioning and Tolerancing: Workbook and Answerbook, James D. Meadows Handbook of Materials Selection for Engineering Applications, edited by G. T. Murray Handbook of Thermoplastic Piping System Design, Thomas Sixsmith and Reinhard Hanselka Practical Guide to Finite Elements: A Solid Mechanics Approach, Steven M. Lepi Applied Computational Fluid Dynamics, edited by Vijay K. Garg Fluid Sealing Technology, Heinz K. Muller and Bernard S. Nau Friction and Lubrication in Mechanical Design, A. A. Seireg Influence Functions and Matrices, Yuri A. Melnikov


DK3151_series.qxd

120. 121. 122. 123. 124. 125. 126. 127. 128. 129. 130. 131. 132. 133. 134. 135. 136. 137. 138. 139. 140. 141. 142. 143. 144. 145. 146. 147. 148. 149. 150.

4/20/05

2:26 PM

Page 5

Mechanical Analysis of Electronic Packaging Systems, Stephen A. McKeown Couplings and Joints: Design, Selection, and Application, Second Edition, Revised and Expanded, Jon R. Mancuso Thermodynamics: Processes and Applications, Earl Logan, Jr. Gear Noise and Vibration, J. Derek Smith Practical Fluid Mechanics for Engineering Applications, John J. Bloomer Handbook of Hydraulic Fluid Technology, edited by George E. Totten Heat Exchanger Design Handbook, T. Kuppan Designing for Product Sound Quality, Richard H. Lyon Probability Applications in Mechanical Design, Franklin E. Fisher and Joy R. Fisher Nickel Alloys, edited by Ulrich Heubner Rotating Machinery Vibration: Problem Analysis and Troubleshooting, Maurice L. Adams, Jr. Formulas for Dynamic Analysis, Ronald L. Huston and C. Q. Liu Handbook of Machinery Dynamics, Lynn L. Faulkner and Earl Logan, Jr. Rapid Prototyping Technology: Selection and Application, Kenneth G. Cooper Reciprocating Machinery Dynamics: Design and Analysis, Abdulla S. Rangwala Maintenance Excellence: Optimizing Equipment Life-Cycle Decisions, edited by John D. Campbell and Andrew K. S. Jardine Practical Guide to Industrial Boiler Systems, Ralph L. Vandagriff Lubrication Fundamentals: Second Edition, Revised and Expanded, D. M. Pirro and A. A. Wessol Mechanical Life Cycle Handbook: Good Environmental Design a nd Manufacturing, edited by Mahendra S. Hundal Micromachining of Engineering Materials, edited by Joseph McGeough Control Strategies for Dynamic Systems: Design and Implementation, John H. Lumkes, Jr. Practical Guide to Pressure Vessel Manufacturing, Sunil Pullarcot Nondestructive Evaluation: Theory, Techniques, and Applications, edited by Peter J. Shull Diesel Engine Engineering: Thermodynamics, Dynamics, Design, and Control, Andrei Makartchouk Handbook of Machine Tool Analysis, Ioan D. Marinescu, Constantin Ispas, and Dan Boboc Implementing Concurrent Engineering in Small Companies, Susan Carlson Skalak Practical Guide to the Packaging of Electronics: Thermal and Mechanical Design and Analysis, Ali Jamnia Bearing Design in Machinery: Engineering Tribology and Lubrication, Avraham Harnoy Mechanical Reliability Improvement: Probability and Statistics for Experimental Testing, R. E. Little Industrial Boilers and Heat Recovery Steam Generators: Design, Applications, and Calculations, V. Ganapathy The CAD Guidebook: A Basic Manual for Understanding and Improving Computer-Aided Design, Stephen J. Schoonmaker


DK3151_series.qxd

151. 152. 153. 154. 155. 156. 157. 158. 159. 160. 161. 162. 163. 164. 165. 166. 167. 168. 169. 170. 171. 172. 173. 174. 175. 176. 177. 178. 179. 180. 181.

4/20/05

2:26 PM

Page 6

Industrial Noise Control and Acoustics, Randall F. Barron Mechanical Properties of Engineered Materials, Wolé Soboyejo Reliability Verification, Testing, and Analysis in Engineering Design, Gary S. Wasserman Fundamental Mechanics of Fluids: Third Edition, I. G. Currie Intermediate Heat Transfer, Kau-Fui Vincent Wong HVAC Water Chillers and Cooling Towers: Fundamentals, Application, and Operation, Herbert W. Stanford III Gear Noise and Vibration: Second Edition, Revised and Expanded, J. Derek Smith Handbook of Turbomachinery: Second Edition, Revised and Expanded, edited by Earl Logan, Jr. and Ramendra Roy Piping and Pipeline Engineering: Design, Construction, Maintenance, Integrity, and Repair, George A. Antaki Turbomachinery: Design and Theory, Rama S. R. Gorla and Aijaz Ahmed Khan Target Costing: Market-Driven Product Design, M. Bradford Clifton, Henry M. B. Bird, Robert E. Albano, and Wesley P. Townsend Fluidized Bed Combustion, Simeon N. Oka Theory of Dimensioning: An Introduction to Parameterizing Geometric Models, Vijay Srinivasan Handbook of Mechanical Alloy Design, edited by George E. Totten, Lin Xie, and Kiyoshi Funatani Structural Analysis of Polymeric Composite Materials, Mark E. Tuttle Modeling and Simulation for Material Selection and Mechanical Design, edited by George E. Totten, Lin Xie, and Kiyoshi Funatani Handbook of Pneumatic Conveying Engineering, David Mills, Mark G. Jones, and Vijay K. Agarwal Clutches and Brakes: Design and Selection, Second Edition, William C. Orthwein Fundamentals of Fluid Film Lubrication: Second Edition, Bernard J. Hamrock, Steven R. Schmid, and Bo O. Jacobson Handbook of Lead-Free Solder Technology for Microelectronic Assemblies, edited by Karl J. Puttlitz and Kathleen A. Stalter Vehicle Stability, Dean Karnopp Mechanical Wear Fundamentals and Testing: Second Edition, Revised and Expanded, Raymond G. Bayer Liquid Pipeline Hydraulics, E. Shashi Menon Solid Fuels Combustion and Gasification, Marcio L. de Souza-Santos Mechanical Tolerance Stackup and Analysis, Bryan R. Fischer Engineering Design for Wear, Raymond G. Bayer Vibrations of Shells and Plates: Third Edition, Revised and Expanded, Werner Soedel Refractories Handbook, edited by Charles A. Schacht Practical Engineering Failure Analysis, Hani M. Tawancy, Anwar Ul-Hamid, and Nureddin M. Abbas Mechanical Alloying and Milling, C. Suryanarayana Mechanical Vibration: Analysis, Uncertainties, and Control, Second Edition, Revised and Expanded, Haym Benaroya


DK3151_series.qxd

182. 183. 184. 185. 186. 187. 188. 189. 190. 191. 192. 193. 194.

4/20/05

2:26 PM

Page 7

Design of Automatic Machinery, Stephen J. Derby Practical Fracture Mechanics in Design: Second Edition, Revised and Expanded, Arun Shukla Practical Guide to Designed Experiments, Paul D. Funkenbusch Gigacycle Fatigue in Mechanical Practive, Claude Bathias and Paul C. Paris Selection of Engineering Materials and Adhesives, Lawrence W. Fisher Boundary Methods: Elements, Contours, and Nodes, Subrata Mukherjee and Yu Xie Mukherjee Rotordynamics, Agnieszka (Agnes) Musznýska Pump Characteristics and Applications: Second Edition, Michael W. Volk Reliability Engineering: Probability Models and Maintenance Methods, Joel A. Nachlas Industrial Heating: Principles, Techniques, Materials, Applications, and Design, Yeshvant V. Deshmukh Micro Electro Mechanical System Design, James J. Allen Probability Models in Engineering and Science, Haym Benaroya and Seon Han Damage Mechanics, George Z. Voyiadjis and Peter I. Kattan


DK3151_title 4/20/05 2:30 PM Page 1

Damage Mechanics George Z. Voyiadjis Peter I. Kattan

Boca Raton London New York Singapore

A CRC title, part of the Taylor & Francis imprint, a member of the Taylor & Francis Group, the academic division of T&F Informa plc.


DK3151_Discl.fm Page 1 Thursday, April 28, 2005 10:00 AM

Published in 2005 by CRC Press Taylor & Francis Group 6000 Broken Sound Parkway NW, Suite 300 Boca Raton, FL 33487-2742 © 2005 by Taylor & Francis Group, LLC CRC Press is an imprint of Taylor & Francis Group No claim to original U.S. Government works Printed in the United States of America on acid-free paper 10 9 8 7 6 5 4 3 2 1 International Standard Book Number-10: 0-8247-2757-6 (Hardcover) International Standard Book Number-13: 978-0-8247-2757-4 (Hardcover) Library of Congress Card Number 2005041839 This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish reliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials or for the consequences of their use. No part of this book may be reprinted, reproduced, transmitted, or utilized in any form by any electronic, mechanical, or other means, now known or hereafter invented, including photocopying, microfilming, and recording, or in any information storage or retrieval system, without written permission from the publishers. For permission to photocopy or use material electronically from this work, please access www.copyright.com (http://www.copyright.com/) or contact the Copyright Clearance Center, Inc. (CCC) 222 Rosewood Drive, Danvers, MA 01923, 978-750-8400. CCC is a not-for-profit organization that provides licenses and registration for a variety of users. For organizations that have been granted a photocopy license by the CCC, a separate system of payment has been arranged. Trademark Notice: Product or corporate names may be trademarks or registered trademarks, and are used only for identification and explanation without intent to infringe.

Library of Congress Cataloging-in-Publication Data Voyiadjis, G. Z. Damage mechanics / George Z. Voyiadjis, Peter I. Kattan. p. cm. -- (Mechanical engineering) Includes bibliographical references and index. ISBN 0-8247-2757-6 1. Continuum damage mechanics. I. Kattan, Peter Issa, 1961- II. Title. III. Mechanical engineering (Taylor & Francis) TA409.V69 2005 620.1'123--dc22

2005041839

Visit the Taylor & Francis Web site at http://www.taylorandfrancis.com Taylor & Francis Group is the Academic Division of T&F Informa plc.


and the CRC Press Web site at http://www.crcpress.com

Dedicated with Love to my wife Christina, my daughter Elena, and son Andrew George Z. Voyiadjis

Dedicated with Love to My Family Peter I. Kattan


Preface

The book presents the principles of continuum damage mechanics including the latest research by the authors. The presentation is theoretical in nature emphasizing the detailed derivations of the various models and formulations. The work of various active researchers in this area is also presented. Both isotropic and anisotropic damage mechanics theories are discussed. Also, both elastic and elasto-plastic damage analyses are presented. The presentation used in this book is consistent and systematic. Many examples illustrating the theory are presented especially in the early chapters of the book. In addition, a large number of problems appear at the ends of sections and chapters for students to be used as practice. The book can be used as a graduate textbook for students in the areas of civil engineering, mechanical engineering, aerospace engineering, materials science, and engineering mechanics. The book can also be used as a reference for active researchers in this field as well as for practicing engineers. Chapter 1 provides the mathematical basis needed to understand the other chapters. This consists of the basics of tensor algebra and analysis. This chapter includes a large number of problems at the end of each section in order to emphasize the importance of this basic chapter for the book. In addition, the authors emphasize the use of the computer algebra system MAPLE in this chapter to solve problems. For this purpose, a short MAPLE tutorial is included and the various sections in the chapter include the needed MAPLE commands. In Chapter 2, a review is made of the basics of the theory of elasticity within the framework of continuum mechanics. Deformation, strains, and stresses are defined and analyzed in this chapter. The principles of continuum damage mechanics are introduced in Chapter 3 as the simple case of isotropic damage is discussed. In particular, the concept of effective stress is presented for the first time in this chapter. In addition, a section on damage evolution appears in this chapter. The kinematic description of damage is described in detail in Chapter 4. Chapter 5 continues with the principles of damage mechanics for the general case of anisotropic damage. The general definition of the effective stress is introduced here as well as a representation of the damage effect tensor. In chapter 6, a review of the theory of plasticity is presented emphasizing kinematic hardening. A constitutive model for damage plasticity is presented in Chapter 7. This involves formulating a coupled


v

vi elasto-plastic damage theory that was developed by the authors. Finally, the kinematics of damage for finite-strain elasto-plastic solids is presented in Chapter 8. The book concludes with a comprehensive reference list. The text increases gradually in difficulty from the basics in the first few chapters to the advanced mathematical and mechanical models in the later chapters. It is written in such a manner that the reader can progress from beginning to end in a very smooth way. Typically, students of damage mechanics are required to have finished the required prerequisites for this topic before reading this book. These prerequisites include tensor algebra, elasticity and plasticity. For those students with the necessary prerequisites, chapters 1, 2, and 6 can be skipped. However, if the students did not finish the necessary prerequisites, then they must read these three chapters (1, 2, and 6) before embarking on a study of damage mechanics. Therefore, this book is comprehensive in the sense that all the prerequisites needed for damage mechanics are reviewed in the book. The presentation is limited to damage mechanics of metals and homogeneous materials. In case the student wishes to apply damage mechanics to metal matrix composites, then he is advised to read a previous book by the authors, entitled “Advances in Damage Mechanics: Metals and Metal Matrix Composites” by Voyiadjis and Kattan. The presentation in the book is also limited to theoretical aspects of damage mechanics. If the student wishes to study the numerical implementation of damage mechanics using finite elements, then he is referred to a previous book by the authors, entitled “Damage Mechanics with Finite Elements: Practical Applications with Computer Tools” by Kattan and Voyiadjis. Finally, the authors would like to express their thanks and appreciation to the editors at Taylor and Francis (CRC Press) for providing the opportunity to publish this book in this form. In addition, the authors wish to thank their family members without whose help and support this book would not have appeared. The second author would like to acknowledge the financial support provided by the Center for Computation and Technology at Louisiana State University, headed by Dr. Edward Seidel. George Z. Voyiadjis [email protected] Peter I. Kattan [email protected]


Authors

Dr. George Z. Voyiadjis, Ph.D. George Z. Voyiadjis is the Boyd Professor at Louisiana State University in the Department of Civil and Environmental Engineering. This is the highest professorial rank awarded by the Louisiana State University System. He joined the faculty of Louisiana State University in 1980. Voyiadjis’ primary research interest is in damage mechanics of metals, metal matrix composites, and ceramics with emphasis on the theoretical modeling, numerical simulation of material behavior, and experimental correlation. Research activities of particular interest encompass macromechanical/micromechanical constitutive modeling, experimental procedure for quantification of crack densities, inelastic behavior, thermal effects, interfaces, damage, failure, fracture, and numerical modeling. His experience also includes work on modeling of cyclic plasticity for metals. He has over 160 referred journal articles and 13 books (9 as editor) to his credit. Over 41 graduate students (21 Ph.D.) completed their degrees under his direction. He has also supervised 11 postdoctoral associates. Voyiadjis has been funded as a principal investigator from the National Science Foundation, the Department of Defense, the Air Force Office of Scientific Research, the Department of Transportation, and major companies such as IBM, and Martin Marietta. He has also been invited to give theme presentations and lectures in many countries around the world and to serve as guest editor in numerous volumes of the Journal of Computer Methods in Applied Mechanics and Engineering, International Journal of Plasticity, Journal of Engineering Mechanics of the ASCE, and Jounal of Mechanics of Materials. These special issues focus on the areas of damage mechanics, structures, fracture mechanics, localization, and bridging of length scales. Dr. Voyiadjis also had a two year stint in industry as a senior engineer with Nuclear Power services , Inc. and Ebasco Services Inc. During that period he was engaged in the research and development of stress analysis of nuclear power plants and was also involved in the development of finite element computer codes in conjunction with the piping analysis of power plants. He is currently a Fellow in the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the American Academy of Mechanics.


vii

viii Dr. Peter I. Kattan, Ph.D. Peter I. Kattan has a Ph.D. in Civil Engineering from Louisiana State University. He has written three books on damage mechanics, one book on finite elements, and one book on composite materials. His research work is currently focused on damage mechanics with fabric tensors and the physical characterization of micro-crack distribution and their evolution. He has published extensively on theory of plates and shells, constitutive modeling of inelastic materials and damage mechanics. He is currently a Visiting Professor at Louisiana State University in Baton Rouge, Louisiana.


Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

v

1 Mathematical Preliminaries 1.1 Maple Tutorial . . . . . . . . . . . . . . 1.2 Vectors . . . . . . . . . . . . . . . . . . . 1.3 Matrices . . . . . . . . . . . . . . . . . . 1.4 Indicial Notation . . . . . . . . . . . . . 1.5 Transformation of Vectors . . . . . . . . 1.6 Cartesian Tensors . . . . . . . . . . . . . 1.7 Eigenvalues and Eigenvectors of Tensors 1.8 Tensor Calculus . . . . . . . . . . . . . . 1.9 Maple Tensor Commands . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

. . . . . . . . .

2 Elasticity Theory 2.1 Motion of a Continuum . 2.2 Deformation and Strain . 2.3 Stress . . . . . . . . . . . 2.4 Linear Elastic Relation . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

77 . 77 . 83 . 94 . 107

3 Isotropic Damage Mechanics 3.1 Introduction . . . . . . . . 3.2 Damage Variables . . . . . 3.3 Effective Stress . . . . . . 3.4 Damage Evolution . . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

. . . .

113 113 115 117 124

4 Kinematic Description of Damage 4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Theoretical Preliminaries . . . . . . . . . . . . . . . . 4.3 Description of Damage State . . . . . . . . . . . . . . 4.4 Fourth-Order Anisotropic Damage Effect Tensor . . . 4.5 Kinematic Description of Elastic-Damage Deformation 4.6 Constitutive Equation of Elastic-Damage Behavior . . 4.7 Conclusion . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . .

. . . . . . .

129 129 130 131 133 135 140 141


1 1 5 17 35 44 50 60 66 74

ix

x 5 Anisotropic Damage Mechanics 5.1 Introduction . . . . . . . . . . . . . . . . . 5.2 Anisotropic Damage Criterion . . . . . . . 5.3 Damage Tensor . . . . . . . . . . . . . . . 5.4 Damage Evolution . . . . . . . . . . . . . 5.5 Constitutive Model . . . . . . . . . . . . . 5.6 Uniaxial Tension Analysis . . . . . . . . . 5.7 Finite Element Implementation . . . . . . 5.8 Center-Cracked Thin Plate Under In-Plane 5.9 Conclusion . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tensile Forces . . . . . . . . .

143 143 144 146 149 153 154 156 158 166

6 Plasticity Theory 6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Theoretical Formulation . . . . . . . . . . . . . . . . . . . 6.3 Monotonic and Cyclic Tension Loadings on 316 Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Modification of the Kinematic Hardening Model for NonProportional Loading . . . . . . . . . . . . . . . . . . . . . 6.5 Model Predictions and Comparisons with Experimental Data for Non-Proportional Loadings . . . . . . . . . . . . . . . 6.6 Ratchetting . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . .

167 167 168

7 Coupled Damage Plasticity 7.1 Stress Transformation between Damaged and Undamaged States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1.1 Effective Stress Tensor . . . . . . . . . . . . . . . . 7.1.2 Effective Backstress Tensor . . . . . . . . . . . . . 7.2 Strain Rate Transformation between Damaged and Undamaged States . . . . . . . . . . . . . . . . . . . . . . 7.2.1 Effective Elastic Strain . . . . . . . . . . . . . . . . 7.2.2 Effective Plastic Strain Rate . . . . . . . . . . . . . 7.3 Constitutive Model . . . . . . . . . . . . . . . . . . . . . . 7.3.1 Damage Evolution . . . . . . . . . . . . . . . . . . 7.3.2 Plastic Deformation . . . . . . . . . . . . . . . . . 7.3.3 Coupling of Damage and Plastic Deformation . . . 7.4 Application to Void Growth: Gurson’s Model . . . . . . . 7.5 Effective Spin Tensor . . . . . . . . . . . . . . . . . . . . .

189

175 181 182 185 187

189 190 192 193 194 195 200 200 202 203 206 209

8 Kinematics of Damage for Finite-Strain Elasto-Plastic Solids 213 8.1 Theoretical Preliminaries . . . . . . . . . . . . . . . . . . 213 8.2 Description of Damage State . . . . . . . . . . . . . . . . 214


xi 8.3 8.4

8.5 8.6

Fourth-Order Anisotropic Damage Effect Tensor . . . . . The Kinematics of Damage for Elasto-Plastic with Finite Strains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.1 A Multiplicative Decomposition . . . . . . . . . . . 8.4.2 Fictitious Damage Deformation Gradients . . . . . 8.4.3 An Additive Decomposition . . . . . . . . . . . . . Irreversible Thermodynamics . . . . . . . . . . . . . . . . Constitutive Equation for Finite Elasto-Plastic Deformation with Damage Behavior . . . . . . . . . . . . . . . . .

References


216 218 220 228 229 232 238 241

1 Mathematical Preliminaries

The mathematical background needed to study damage mechanics is introduced in this chapter. In particular, vectors and tensors are introduced using the computer algebra system Maple. A short Maple tutorial is given first followed by vector and tensor analysis. It should be noted that the coverage of vectors and tensors is not comprehensive – only the needed material is shown. For more details, the reader is referred to the references by Chung (1996), Eringen (1980), Fung (1965), Fung (1994), Green and Zerna (1968), Hjelmstad (1997), Lai et al. (1984), Lubliner (1990), Maugin (1992), Marsden and Hughes (1983), Lemaitre (1996), McDonald (1996), Mroz (1973), Segel (1987), and Werde (1972).

1.1

Maple Tutorial

In this section a short tutorial on using the computer algebra system Maple is given. For more details the reader is referred to the Maple books by Corless (1995), Heck (1996), Nicolaides and Walkington (1996), Kofler (1997), Schwartz (1999), and Cornil and Testud (2001). In addition, a search for Maple on the internet will reveal several Maple tutorials which can be freely downloaded. Once you start Maple on your computer system, you can start using it immediately as a calculator as follows: >

3+1/2; 7 2

Note that each Maple command is terminated by a semicolon. Note also that the result is given in exact form (in the form of a fraction in the example above). In case a numerical result is needed, you can use the Maple function evalf as follows:


1

2

Damage Mechanics >

evalf(3+1/2); 3.500000000

Maple can be used easily to perform all sorts of algebraic manipulations like simplifying, expanding, and factoring. The following examples illustrate this: >

expand((x+2)^3); x3 + 6 x2 + 12 x + 8

>

simplify(sin(x)^2 + cos(x)^2); 1

Maple can also be used to solve algebraic equations as follows: >

solve(2*x^3 +5*x^2 -x -4,x); 3 1√ 3 1√ 41, − − 41 −1, − + 4 4 4 4

Systems of simultaneous algebraic equations can be solved numerically using the Maple command fsolve as follows: >

fsolve({x^2 -3*y^2 +6 = 0, sin(x)*sqrt(y) = 2},{x,y}); {x = 7.497717372, y = 4.553964053}

Differential and integral calculus can be performed using the Maple commands diff and int as follows: >

diff(x^5 - 2*x^3 + x^2 + 10, x);

5 x4 − 6 x2 + 2 x > int(2*cos(5*x)^3,x=a..b); 2 2 4 4 cos(5 b)2 sin(5 b) + sin(5 b) − cos(5 a)2 sin(5 a) − sin(5 a) 15 15 15 15 Simple ordinary differential equations can also be solved using the Maple command dsolve as follows: >

deq:=diff(y(x),x)*y(x)*(1-x^2) = 5*x - 1;


Mathematical Preliminaries

3

1 0.8 0.6 0.4 0.2 0

1

2

3 x

4

5

6

FIGURE 1.1 Two-Dimensional Plot Using Maple ∂ y(x)) y(x) (1 − x2 ) = 5 x − 1 deq := ( ∂x >

dsolve({deq,y(0)=0},y(x)); y(x) = −2 arctanh(x) + 5 I π − 5 ln(−1 + x2 ), y(x) = − −2 arctanh(x) + 5 I π − 5 ln(−1 + x2 )

Finally, two-dimensional and three-dimensional graphs can be plotted using the Maple commands plot and plot3d as follows: >

plot(cos(x)*exp(1)^(-2*x/3),x=0..2*Pi);

>

plot3d(sin(x)*cos(y),x=0..2*Pi,y=0..2*Pi,axes=boxed);

See Figures 1.1 and 1.2 for the resulting plots of the above two commands, respectively.

Problems 1.1 Perform the following calculations using Maple. Obtain an exact result first followed by a numerical answer.


4

Damage Mechanics

1 0.5 0 –0.5 –1 0

1

2

y3

4

5

6

6

5

4

3x

2

1

0

FIGURE 1.2 Three-Dimensional Plot Using Maple (a)

√ 788

(b) cos( Π2 ) (c)

1

1 1 2+3

(d) 57 + e3 1.2 Perform the following algebraic manipulations using Maple. (a) Expand the expression (2x − 1)5 (b) Factor the expression cos4 x − sin4 x (c) Simplify the expression 1 − sin2 x − cos2 x 1.3 Solve each one of the following equations using Maple. (a) x2 − 2x + 1 = 0 (b) x4 + x3 − 2x2 − x + 1 = 0 (c) y 2 ey = 5 (d) sin(2x) cos(2x) = 1 1.4 Obtain a numerical solution to each of the following sets of simultaneous algebraic equations using Maple. (a) x + 2y = 5 ; 3x − 5y = 4 (b) x2 + y 2 = 20 ; y ∗ sin(x) = 2



5

1.5 Determine the specified derivative for each given expression using Maple. (a)

dy dx

(b)

dy 2 dx2

(c)

dy dx

for y = 3x5 − 2x2 + x + 1 for y = ex sin(2x) √ for x + 3 y = 15

1.6 Determine

f (x)dx for each f (x) given below using Maple.

(a) f (x) = x2 + 2x + 1 (b) f (x) = cos2 (4x) + sin(2x) (c) f (x) =

x x2 +1

1.7 Solve each of the following ordinary differential equations using Maple. dy (a) 2 dx + y + 5 = 0, 2 (b) x3 y dy dx = 2x + x + 1,

y(0) = 0 y(1) = 1

1.8 Plot a graph for each of the following functions using Maple. (a) sin( x2 ) + 2 cos( x3 ), 0 ≤ x ≤ 6Π (b) sin( x2 ) + 2 cos( y3 ), 0 ≤ x ≤ 4Π; 0 ≤ y ≤ 6Π

1.2

Vectors

In this section we explore vectors and vector operations using Maple. In order to use vectors in Maple, we need first to invoke the linear algebra package using the following command:

>

with(linalg);

Warning, the protected names norm and trace have been redefined and unprotected


6

Damage Mechanics

[BlockDiagonal , GramSchmidt , JordanBlock , LUdecomp, QRdecomp, Wronskian, addcol , addrow , adj , adjoint , angle, augment, backsub, band , basis, bezout, blockmatrix , charmat , charpoly , cholesky , col , coldim, colspace, colspan, companion , concat, cond , copyinto, crossprod , curl , definite, delcols, delrows, det , diag , diverge, dotprod , eigenvals , eigenvalues , eigenvectors, eigenvects, entermatrix , equal , exponential , extend, ffgausselim, fibonacci , forwardsub, frobenius, gausselim, gaussjord , geneqns, genmatrix , grad , hadamard , hermite, hessian, hilbert , htranspose, ihermite, indexfunc, innerprod , intbasis, inverse, ismith, issimilar , iszero, jacobian , jordan, kernel , laplacian , leastsqrs, linsolve, matadd , matrix , minor , minpoly , mulcol , mulrow , multiply, norm, normalize, nullspace, orthog, permanent , pivot , potential , randmatrix , randvector , rank , ratform, row , rowdim, rowspace, rowspan, rref , scalarmul , singularvals, smith, stackmatrix , submatrix , subvector , sumbasis, swapcol , swaprow , sylvester , toeplitz , trace, transpose, vandermonde, vecpotent , vectdim, vector , wronskian] Figure 1.3 shows a two-dimensional vector A where A=(2,3). This vector can be defined in Maple as follows: >

A:=vector([2,3]); A := [2, 3]

A three-dimensional vector B where B=(1,3,-4) is shown in Figure 1.4. This vector can be defined in Maple as follows: >

B:=vector([1,3,-4]); B := [1, 3, −4]

Vectors can also be defined in Maple using variables or symbols as follows: >

v1:=vector([x,y,z]);

>

v1 := [x, y, z] v2:=vector([2*a,0,b-1]); v2 := [2 a, 0, b − 1]

The Maple command evalm can be used to perform some simple vector operations as follows: >

v:=vector([1,0,2]);



7

y

5

4

3

(2,3)

2 A

1

1

2

3

4

5

x

FIGURE 1.3 → − A two-dimensional vector A v := [1, 0, 2] >

w:=evalm(v+4); w := [5, 4, 6]

The above command will add 4 to each element of the vector v. Scalar multiplication can also be performed as follows: >

y:=evalm(3*v); y := [3, 0, 6]

Alternatively, the special Maple command scalarmul can be used to perform scalar multiplication as follows:


8

Damage Mechanics y

(1,3,-4) 4

3 B 2

1

1

2

3

4

x

z

FIGURE 1.4 → − A three-dimensional vector B >

y:=scalarmul(v,3); y := [3, 0, 6]

The command evalm can be used to perform various operations on vectors like vector addition and subtraction as follows: >

a:=vector([x,0,2]);

>

b:=vector([1,1,y]);

a := [x, 0, 2] b := [1, 1, y] >

c:=evalm(a+b); c := [x + 1, 1, 2 + y]

>

d:=evalm(a-b);

>

d := [x − 1, −1, 2 − y] e:=evalm(2*a+3*b-c);



9

e := [x + 2, 2, 2 + 2 y] Vector products like the dot product and cross product can be performed on two vectors using the Maple commands dotprod and crossprod as follows: >

v:=vector([x,x^2,x^3]);

>

v := [x, x2 , x3 ] w:=vector([1,2,3]); w := [1, 2, 3] u:=dotprod(v,w);

>

u := x + 2 x2 + 3 x3 y:=crossprod(v,w);

>

y := [3 x2 − 2 x3 , x3 − 3 x, 2 x − x2 ] The norm of a vector can be calculated using the Maple command norm. Several norms can be calculated according to the following formulae for a three-dimensional vector v = (v1 , v2 , v3 ) v∞ = max(|v1 |, |v2 |, |v3 |)

(1.1a)

v1 = |v1 | + |v2 | + |v3 | v2 = (v1 )2 + (v2 )2 + (v3 )2 v3 = 3 (v1 )3 + (v2 )3 + (v3 )3

(1.1b)

In general, the n-norm vn is defined by the formula: vn = n (v1 )n + (v2 )n + (v3 )n

(1.1c) (1.1d)

(1.2)

The norm command has two arguments, norm(v,n) where v is the vector and n=1,2,3,... is the order of the norm. The infinity-norm v∞ is obtained by using the norm command with one argument only, norm(v). The following examples illustrate the use of the norm command: >

v:=vector([1,2,3]); v := [1, 2, 3]

>

norm(v); 3

>

norm(v,1); 6


10

Damage Mechanics >

norm(v,2);

>

norm(v,3);

√ 14 36(1/3)

>

evalf(norm(v,3)); 3.301927249

The command normalize is used to normalize a vector to a unit vector of length 1 using the following formula for a three-dimensional vector v = (v1 , v2 , v3 ): v1 v2 v3 , , ) (1.3) vnormalized = ( v2 v2 v2 The normalize command is illustrated by the following example: >

v:=vector([2,3,7]); v := [2, 3, 7]

>

normalize(v);

1 √ 3 √ 7 √ 62, 62, 62 31 62 62

It should be noted that the length of a vector is equal to its 2-norm as follows: |v| = v2 (1.4) The angle θ between two vectors u and v is calculated using the formula: cos θ =

u·v u2 v2

(1.5)

In Maple the command angle can be used to calculate the angle between two vectors. The resulting angle is given in radians - multiply it by 180 π to convert it into degrees as in the following example: >

u:=vector([1,1,1]); u := [1, 1, 1]

>

v:=vector([1,0,2]);

>

theta:=angle(u,v);

v := [1, 0, 2]

θ := arccos(


1√ √ 3 5) 5

Mathematical Preliminaries >

>

11

theta:=evalf(theta); θ := .6847192024 theta:=evalf(theta*180/Pi); θ := 39.23152043

Maple can deal with general vectors in terms of their components even if these components are not specified. We can define two vectors u and v each with three unspecified components as follows: >

u:=vector(3); u := array(1..3, [])

>

v:=vector(3); v := array(1..3, [])

The above commands define general three-dimensional vectors u and v with their components (u1 , u2 , u3 ) and (v1 , v2 , v3 ) unspecified. All the previous operations in this section can be applied to these vectors as shown in the following examples: >

evalm(u+v);

>

[u1 + v1 , u2 + v2 , u3 + v3] evalm(2*u-3*v); [2 u1 − 3 v1 , 2 u2 − 3 v2 , 2 u3 − 3 v3] scalarmul(v,3); [3 v1 , 3 v2 , 3 v3] dotprod(u,v);

>

u1 (v1 ) + u2 (v2 ) + u3 (v3 ) crossprod(u,v);

>

>

>

>

[u2 v3 − u3 v2 , u3 v1 − u1 v3 , u1 v2 − u2 v1] norm(v,2); 2 2 2 |v1 | + |v2 | + |v3 | normalize(u); u2 u3 u1 √ , √ , √ %1 %1 %1 %1 := |u1 |2 + |u2 |2 + |u3 |2

>

angle(u,v);


12

Damage Mechanics u1 v1 + u2 v2 + u3 v3 √ arccos √ 2 u1 + u2 2 + u3 2 v1 2 + v2 2 + v3 2

Defining general vectors in Maple is very helpful especially in deriving complicated equations involving vectors.

Example 1.1 Consider two three-dimensional vectors u and v . Use Maple to show that | u − v |2 =| u |2 + | v |2 −2 | u || v | cos θ

(1.6)

where θ is the angle between the two vectors. Solution Use general vectors to define u and v as three-dimensional vectors in Maple as follows: >

u:=vector(3);

>

v:=vector(3);

u := array(1..3, []) v := array(1..3, []) Next, evaluate the left-hand side using Maple as follows: >

w:=evalm(u-v);

>

w := [u1 − v1 , u2 − v2 , u3 − v3] x:=norm(w,2); 2 2 2 x := |−u1 + v1 | + |−u2 + v2 | + |−u3 + v3 | left_side:=x^2;

>

left side := |−u1 + v1 | + |−u2 + v2 | + |−u3 + v3 | left_side:=simplify(left_side, symbolic);

>

2

2

2

left side := u1 2 + u2 2 + u3 2 + v1 2 + v2 2 + v3 2 − 2 u1 v1 − 2 u2 v2 − 2 u3 v3 Finally, evaluate the right-hand side using Maple as follows: >

y:=norm(u,2); y :=


2 2 2 |u1 | + |u2 | + |u3 |


>

>

13

z:=norm(v,2);

2 2 2 z := |v1 | + |v2 | + |v3 | theta:=angle(u,v); u1 v1 + u2 v2 + u3 v3 √ θ := arccos √ 2 u1 + u2 2 + u3 2 v1 2 + v2 2 + v3 2 right_side:=y^2 + z^2 -2*y*z*cos(theta); 2

2

2

2

2

2

right side := |u1 | + |u2 | + |u3 | + |v1 | + |v2 | + |v3 | 2 |u1 |2 + |u2 |2 + |u3 |2 |v1 |2 + |v2 |2 + |v3 |2 (u1 v1 + u2 v2 + u3 v3 ) √ √ − u1 2 + u2 2 + u3 2 v1 2 + v2 2 + v3 2 > right_side:=simplify(right_side, symbolic); right side := u1 2 + u2 2 + u3 2 + v1 2 + v2 2 + v3 2 − 2 u1 v1 − 2 u2 v2 − 2 u3 v3 It is seen that both sides give the same result in Maple. Thus, equation (1.6) is true.

Problems 1.9 Define each of the following vectors using Maple: (a) a = (1, 1, −1) (b) b = (0, 2x, y 3 ) (c) v = (0, 0, 0, 0) (d) w = (y, y − 1) (e) A general three-dimensional vector x = (x1 , x2 , x3 ) 1.10 Consider the two vectors u = (2, 0, −1) and v = (3, 3, 3). Perform the following operations using Maple: (a) u − 2 (subtract 2 from each element of u) (b) 3v (c) u + v (d) u − v (e) 3u + 5v − 1 (f) v · u (g) v × u 1.11 Consider the vector u = (1, −1, −1). Calculate the following norms using Maple:


14

Damage Mechanics (a) (b) (c) (d)

u1 u2 u3 u∞

1.12 Normalize the vector u=(8,-2,3) using Maple. 1.13 Determine the angle (in degrees) between the two vectors a = (2, 0, 1) and b = (1, −1, −2) using Maple. 1.14 Consider two two-dimensional vectors u = (u1 , u2 ) and v = (v1 , v2 ) as shown in Figure 1.5. Let θ be the angle between the two vectors. Prove equation (1.5) for these two vectors using the geometry of the problem.

y

v

u θ

x FIGURE 1.5 Two-dimensional vectors u and v



15

1.15 Define two general three-dimensional vectors u = (u1 , u2 , u3 ) and v = (v1 , v2 , v3 ). Perform the following operations using Maple: (a) u + 2v (b)

3 2u

(c) (u × v) + (v × u) (d) Normalize u + v (e) Calculate the 2-norm of u − v 1.16 Consider two points A = (5, 0, 2) and B = (4, 4, 1) in three-dimensional space. Determine the vector AB starting at A and ending at B using Maple. 1.17 Determine the length of the vector v = (2, 0, 3) using Maple. 1.18 Consider two general three-dimensional vectors u and v. Suppose that u2 = v2 . Give an example where this holds but u = v. 1.19 Consider two general three-dimensional vectors u and v. Use Maple to show that the angle θ between the two vectors can be calculated using the following formula: sin2 θ =

(u · u)(v · v) − (u · v)2 (u · u)(v · v)

1.20 Use vectors and Maple to determine the angle between the face diagonals of a cube. 1.21 Consider three three-dimensional vectors u, v, and w. Prove the following relationships using Maple. (a) u · (v × w) = (u × v) · w (b) u × (v × w) = v(u · w) − w(u · v) (c) u × (v × w) + v × (w × u) + w × (u × v) = 0 (d) u × u = 0 (e) (u + v) · (v + w) × (w + u) = 2u · v × w 1.22 Consider four three-dimensional vectors u, v, p, and q. Prove the following relations using Maple: (a) (u × v) × (p × q) = p(u × v · q) − q(u × v · p) (b) (u × v) · (p × q) = (u · p)(v · q) − (u · q)(v · p)


16

Damage Mechanics

1.23 Consider two vectors u and v satisfying the equation u = αv where α is a scalar. Show that α=

| u |2 u·v = | v |2 u·v

1.24 Prove the Law of Cosines using vectors. (Hint : Consider the vector w = u − v and calculate the dot product w · w). 1.25 Prove the Law of Sines using vectors. (Hint : Consider the cross products u × v = v × w = w × u and use | u × v |=| u || v | sin θ where θ is the angle between u and v, see Figure 1.6).

w

v θ u

FIGURE 1.6 Three vectors u, v, and w.

1.26 Consider three vectors u, v, and w such that u and v are orthogonal (i.e., u · v = 0). Let θ be the angle between u and v. Suppose the following relation holds: w = αu + βv where α and β are scalars. Show that α and β can be obtained using the following formulae: α=

|w| cos θ |u|

β=

|w| sin θ |v|

1.27 Consider a parallelogram with sides given by vectors u and v. Show that the area of the parallelogram is given by | u × v |=| u || v | sinθ where θ is the angle between u and v.



17

1.28 Find the area of the triangle with vertices (1, 2, −1), (4, −5, 3), and (0, 2, 1). Use Maple. (Hint : Use the vectors and the result of Problem 1.27 above.) 1.29 Consider a three-dimensional vector u = (x, y, z) which starts at the origin and ends at the point (x, y, z). Determine the angles α, β, and γ which the vector makes with the positive directions of the coordinate axes and show that: cos2 α + cos2 β + cos2 γ = 1

1.3

Matrices

In this section we explore matrices and matrix operations using Maple. In order to use matrices in Maple, you need first to invoke the linear algebra package as follows: >

with(linalg);

Warning, the protected names norm and trace have been redefined and unprotected

[BlockDiagonal , GramSchmidt , JordanBlock , LUdecomp, QRdecomp, Wronskian, addcol , addrow , adj , adjoint , angle, augment, backsub, band , basis, bezout, blockmatrix , charmat , charpoly , cholesky , col , coldim, colspace, colspan, companion , concat, cond , copyinto, crossprod , curl , definite, delcols, delrows, det , diag , diverge, dotprod , eigenvals , eigenvalues , eigenvectors, eigenvects, entermatrix , equal , exponential , extend, ffgausselim, fibonacci , forwardsub, frobenius, gausselim, gaussjord , geneqns, genmatrix , grad , hadamard , hermite, hessian, hilbert , htranspose, ihermite, indexfunc, innerprod , intbasis, inverse, ismith, issimilar , iszero, jacobian , jordan, kernel , laplacian , leastsqrs, linsolve, matadd , matrix , minor , minpoly , mulcol , mulrow , multiply, norm, normalize, nullspace, orthog, permanent , pivot , potential , randmatrix , randvector , rank , ratform, row , rowdim, rowspace, rowspan, rref , scalarmul , singularvals, smith, stackmatrix , submatrix , subvector , sumbasis, swapcol , swaprow , sylvester , toeplitz , trace, transpose, vandermonde, vecpotent , vectdim, vector , wronskian] Consider the following three matrices:


18

Damage Mechanics

1 3 A= −2 5

⎡

⎤ 2 x y B = ⎣ x2 2y −1 ⎦ 0 xy x + y ⎡

1 r ⎢0 2 C=⎢ ⎣ r r2 1 0

⎤ r2 r3 −1 0 ⎥ ⎥ r3 r4 ⎦ 2 −r

The above three matrices can be defined in Maple as follows: >

>

>

A:=matrix([[1,3],[-2,5]]); 13 A := −2 5 B:=matrix([[2,x,y],[x^2,2*y,-1],[0,x*y,x+y]]); ⎤ ⎡ 2 x y B := ⎣ x2 2 y −1 ⎦ 0 xy x + y C:=matrix([[1,r,r^2,r^3],[0,2,-1,0],[r,r^2,r^3,r^4],[1,0,2,-r]]); ⎡ ⎤ 1 r r2 r3 ⎢ 0 2 −1 0 ⎥ ⎥ C := ⎢ ⎣ r r2 r3 r4 ⎦ 1 0 2 −r

In addition to the Maple command matrix used above, the Maple command array can be used to define special types of matrices like the zero matrix and identity matrix as follows: >

A:=array(sparse,1..3,1..3);

>

A := array(sparse, 1..3, 1..3, []) B:=array(identity,1..4,1..4); B := array(identity, 1..4, 1..4, [])

The Maple command diag can be used to define diagonal matrices as follows:



>

19

C:=diag(x,x^2,x^3);

⎤ x 0 0 C := ⎣ 0 x2 0 ⎦ 0 0 x3 ⎡

A banded matrix can be defined using the Maple command band as follows: >

E:=band([1,2,-1],5); ⎡

⎤ 2 −1 0 0 0 ⎢ 1 2 −1 0 0 ⎥ ⎢ ⎥ ⎥ E := ⎢ ⎢ 0 1 2 −1 0 ⎥ ⎣ 0 0 1 2 −1 ⎦ 0 0 0 1 2

In the example above, the second argument indicates the size of the banded matrix. The Jacobian matrix can be defined using the Maple command jacobian as follows: >

f:=x^2+y^2+x^2; f := 2 x2 + y 2

>

g:=x-y-z; g := x − y − z

>

>

h:=3*x*y*z; h := 3 x y z J:=jacobian([f,g,h],[x,y,z]); ⎡ ⎤ 4x 2y 0 J := ⎣ 1 −1 −1 ⎦ 3yz 3xz 3xy

In order to extract an element from a matrix, use the name of the matrix followed by square brackets. For example, the command A[1,2] will extract the element in row 1 and column 2 of the matrix A. In order to extract a submatrix or a subvector, the Maple commands submatrix and subvector are used, respectively. These are illustrated by the following example: >

B:=matrix([[3,5,7,9],[-1,0,1,5],[x,y,z,w],[r,p,q,s]]);


20

Damage Mechanics ⎡

3 5 ⎢ −1 0 B := ⎢ ⎣ x y r p >

7 1 z q

⎤ 9 5⎥ ⎥ w⎦ s

B[3,2]; y

>

submatrix(B,2..3,3..4); 1 5 zw

>

submatrix(B,[2,4],[1,3]); −1 1 r q

>

subvector(B,3,1..4); [x, y, z, w]

>

subvector(B,[1,3,2],2); [5, y, 0]

>

row(B,3); [x, y, z, w]

>

col(B,4); [9, 5, w, s]

The Maple command row and col were used above to extract the third row and the fourth column of matrix B, respectively. The Maple command transpose is used to obtain the transpose of a matrix. The transpose of matrix B is obtained as follows: >

C:=transpose(B);

⎡

3 −1 x ⎢5 0 y ⎢ C := ⎣ 7 1 z 9 5w

⎤ r p⎥ ⎥ q⎦ s

The Maple commands inverse and det are used to obtain the inverse and determinant of a square matrix, respectively. The inverse and determinant of matrix B above are obtained as follows: >

B:=matrix([[3,6,3,8],[1,0,6,4],[1,2,3,4],[9,10,5,4]]);



21 ⎡

3 ⎢1 B := ⎢ ⎣1 9 >

C:=inverse(B);

⎤ 638 0 6 4⎥ ⎥ 2 3 4⎦ 10 5 4

⎡

⎤ 1 1 −3 0 ⎢ −6 −13 71 3 ⎥ ⎢ ⎥ ⎢ 7 14 28 28 ⎥ ⎢ ⎥ C := ⎢ −4 −2 19 1 ⎥ ⎢ ⎥ ⎢ 7 7 14 14 ⎥ ⎣ ⎦ 17 3 −9 −3 28 7 7 28

>

d:=det(B); d := 112

The trace (sum of the diagonal elements) of a square matrix can be obtained using the Maple command trace. The trace of matrix B above is calculated as follows: >

t:=trace(B); t := 10

The Maple command evalm can be used to perform several matrix operations like matrix addition, matrix subtraction, scalar multiplication, and matrix multiplication, as shown in the following examples: >

>

>

A:=matrix([[2,5,8],[0,4,6],[1,2,4],[3,7,5]]); ⎡ ⎤ 258 ⎢0 4 6⎥ ⎥ A := ⎢ ⎣1 2 4⎦ 375 B:=matrix([[1,2,6,7],[3,4,6,8],[1,1,1,5]]); ⎡ ⎤ 1267 B := ⎣ 3 4 6 8 ⎦ 1115 C:=evalm(A*2); ⎡ ⎤ 4 10 16 ⎢ 0 8 12 ⎥ ⎥ C := ⎢ ⎣2 4 8⎦ 6 14 10


22

Damage Mechanics >

>

>

>

>

E:=evalm(B-3);

⎡

⎤ −2 2 6 7 E := ⎣ 3 1 6 8 ⎦ 1 1 −2 5 F:=evalm(A+transpose(B)); ⎡ ⎤ 3 8 9 ⎢ 2 8 7⎥ ⎥ F := ⎢ ⎣ 7 8 5⎦ 10 15 10 G:=evalm(A&*B); ⎡ ⎤ 25 32 50 94 ⎢ 18 22 30 62 ⎥ ⎥ G := ⎢ ⎣ 11 14 22 43 ⎦ 29 39 65 102 H:=evalm(B&*A); ⎡ ⎤ 29 74 79 H := ⎣ 36 99 112 ⎦ 18 46 43 J:=evalm(1/H); ⎡ 895 −452 −467 ⎤ ⎢ 1277 1277 1277 ⎥ ⎢ ⎥ ⎢ −468 175 404 ⎥ J := ⎢ ⎥ ⎢ 1277 1277 1277 ⎥ ⎣ ⎦ 126 2 −207 1277 1277 1277

It should be noted from the above examples that the operator & is used to indicate matrix multiplication. Multiplying a matrix and a vector is also easily performed in Maple as shown in the following examples: >

>

>

A:=matrix([[7,4,5],[2,2,6],[-7,5,-5]]); ⎡ ⎤ 74 5 A := ⎣ 2 2 6 ⎦ −7 5 −5 e:=vector([2,-1,3]); e := [2, −1, 3] c:=evalm(A&*e); c := [25, 20, −34]

>

d:=vector([[2],[-1],[3]]);



23 d := [[2], [−1], [3]]

>

f:=evalm(A&*d);

⎡

⎤ 25 f := ⎣ 20 ⎦ −34

However, in order to multiply a vector and a matrix, the Maple command innerprod must be used. The following example uses A and b as defined above to multiply the vector b and the matrix A: >

j:=innerprod(b,A); j := [−9, 21, −11]

Matrices can be used to solve systems of linear simultaneous equations. Consider the following system of equations: 2x − y + 3z = 4 x + 3y + 5z = −1 y−z =2 The above system of equations can be written in matrix form as Ax=b, where A, B, and x are given by: ⎡

⎤ 2 −1 3 A = ⎣1 3 5 ⎦ 0 1 −1 ⎡

⎤ 4 b = ⎣ −1 ⎦ 2 ⎡ ⎤ x x = ⎣y ⎦ z In order to solve the above system of linear equations, the Maple command linsolve is used as follows:


24

Damage Mechanics >

A:=matrix([[2,-1,3],[1,3,5],[0,1,-1]]); ⎡ ⎤ 2 −1 3 A := ⎣ 1 3 5 ⎦ 0 1 −1

>

b:=vector([4,-1,2]); b := [4, −1, 2]

>

x:=linsolve(A,b);

31 4 −10 , , x := 7 7 7

It should be noted that the command linsolve is used only to solve linear systems. Alternatively, one can use the inverse matrix of A to obtain the solution as follows:

>

x:=evalm(inverse(A)&*b); 31 4 −10 x := , , 7 7 7

It should be noted that using the inverse matrix takes more time to perform the calculations than using the command linsolve. The eigenvalue of a matrix A are scalar values λ such that the equation Ax = λx

(1.7)

has one or more solution vectors x. The solution vectors x are called the eigenvectors of A. The eigenvalues and eigenvectors of a matrix are calculated using the Maple commands eigenvals and eigenvects, respectively. This is illustrated as follows:

>

A:=matrix([[1.2,-2.4,0],[2.3,3.6,1.1],[-2.0,3.0,1.4]]); ⎡ ⎤ 1.2 −2.4 0 A := ⎣ 2.3 3.6 1.1 ⎦ −2.0 3.0 1.4

>

lambda:=eigenvals(A);

λ := 1.234939238 + 1.588073742 I, 1.234939238 − 1.588073742 I, 3.730121523 >

x:=eigenvects(A);



25

x := [1.234939240 + 1.588073741 I, 1, {[−.9558375413 − .8201580128 I, −.5287813216 + .6444150787 I, 2.205134200 − .4340555658 I]}], [ 1.234939240 − 1.588073741 I, 1, {[−.9558375413 + .8201580128 I, −.5287813216 − .6444150787 I, 2.205134200 + .4340555658 I]}], [3.730121526, 1, {[−.5919850763, .6240809050, 1.311610933]}] The orthonomal basis for a given set of vectors can be obtained using the Maple command GramSchmidt as follows: >

>

>

v1:=vector([1,2,3,4,5]); v1 := [1, 2, 3, 4, 5] v2:=vector([-1,0,1,2,1]); v2 := [−1, 0, 1, 2, 1] v3:=vector([1,-1,1,-1,2]);

v3 := [1, −1, 1, −1, 2] > GramSchmidt([v1,v2,v3]); −14 −6 2 10 −4 −1 −17 7 −9 [[1, 2, 3, 4, 5], [ , , , , ], [ , , , , 1]] 11 11 11 11 11 10 10 10 10 The resulting basis vectors above are normal to each other (use the Maple command dotprod to check this) but they are not unit vectors. Maple does not automatically normalize them to unit vectors. For this purpose, the normalize command should be used as was shown in Section 1.2. General matrices can be defined in Maple even if their elements (or components) are not explicitly known. Consider the following examples and operations on general matrices using Maple: >

>

>

>

>

A:=matrix(3,3); A := array(1..3, 1..3, []) B:=matrix(3,3); B := array(1..3, 1..3, []) x:=subvector(A,2,1..3); x := [A2, 1 , A2, 2 , A2, 3] C:=transpose(B); ⎤ ⎡ B1, 1 B2, 1 B3, 1 C := ⎣ B1, 2 B2, 2 B3, 2 ⎦ B1, 3 B2, 3 B3, 3 d:=det(B);


26

Damage Mechanics

d := B1, 1 B2, 2 B3, 3 − B1, 1 B2, 3 B3, 2 − B2, 1 B1, 2 B3, 3 + B2, 1 B1, 3 B3, 2 + B3, 1 B1, 2 B2, 3 − B3, 1 B1, 3 B2, 2 >

t:=trace(A); t := A1, 1 + A2, 2 + A3, 3

>

E:=evalm(A+2*B); ⎡ ⎤ A1, 1 + 2 B1, 1 A1, 2 + 2 B1, 2 A1, 3 + 2 B1, 3 E := ⎣ A2, 1 + 2 B2, 1 A2, 2 + 2 B2, 2 A2, 3 + 2 B2, 3 ⎦ A3, 1 + 2 B3, 1 A3, 2 + 2 B3, 2 A3, 3 + 2 B3, 3

>

F:=evalm(A&*B);

F := A1, 1 B1, 1 + A1, 2 B2, 1 + A1, 3 B3, 1 , A1, 1 B1, 2 + A1, 2 B2, 2 + A1, 3 B3, 2 , A1, 1 B1, 3 + A1, 2 B2, 3 + A1, 3 B3, 3 A2, 1 B1, 1 + A2, 2 B2, 1 + A2, 3 B3, 1 , A2, 1 B1, 2 + A2, 2 B2, 2 + A2, 3 B3, 2 , A2, 1 B1, 3 + A2, 2 B2, 3 + A2, 3 B3, 3 A3, 1 B1, 1 + A3, 2 B2, 1 + A3, 3 B3, 1 , A3, 1 B1, 2 + A3, 2 B2, 2 + A3, 3 B3, 2 , A3, 1 B1, 3 + A3, 2 B2, 3 + A3, 3 B3, 3 Defining general matrices in Maple is very helpful especially in deriving complicated equations involving matrices.

Example 1.2 Let M be a matrix and v be a vector given by: ⎡

⎤ 2 −1 0 A = ⎣ −1 2 −1 ⎦ 0 −1 2 ⎡

⎤ 1 v=⎣x⎦ x2 Calculate the product vT Mv using Maple.



27

Solution The following are the necessary Maple commands to calculate vT Mv: >

>

M:=matrix([[2,-1,0],[-1,2,-2],[0,-1,2]]); ⎡ ⎤ 2 −1 0 M := ⎣ −1 2 −2 ⎦ 0 −1 2 v:=vector([1,x,x^2]); v := [1, x, x2 ]

>

c:=innerprod(v,M,v); c := 2 − 2 x + 2 x2 − 3 x3 + 2 x4

Example 1.3 (a) Consider a general square matrix A . The adjoint matrix of A, called adjA, is defined by: A(adjA) = (adjA)A =| A | I

(1.8)

where | A | is the determinant of A. Use the definition above to find a general expression for the adjoint matrix of A. (b) Find the adjoint matrix of A if A is given by: ⎤ 1 x x2 A = ⎣ 0 −1 2 ⎦ 1 0 x ⎡

Solution (a) Divide both sides of equation (1.8) by |A|: 1 1 A(adjA) = (adjA)A = I |A| |A| Rewrite the above equation as follows: A(

adjA adjA )=( )A = I |A| |A|

However, we know that


28

Damage Mechanics

AA−1 = A−1 A = I Therefore, we conclude that A−1 =

adjA |A|

The adjoint matrix of A is then given by: adjA =| A | A−1

(1.9)

(b) The following are the Maple commands to find the adjoint matrix of the given matrix A using equation (1.9). A:=matrix([[1,x,x^2],[0,-1,2],[1,0,x]]); ⎡ ⎤ 1 x x2 A := ⎣ 0 −1 2 ⎦ 1 0 x > adjoint_matrix:=det(A)*inverse(A); ⎤ ⎡ x 2+x 1 − − ⎥ ⎢ 1+x 1+x 1+x ⎥ ⎢ ⎥ ⎢ 1 x − 1 1 2 ⎢2 ⎥ − −2 adjoint matrix := (x + x ) ⎢ x (1 + x) ⎥ ⎥ ⎢ x (1 + x) 1 + x ⎦ ⎣ 1 1 1 − x (1 + x) 1 + x x (1 + x) >

Example 1.4 Consider the matrix M given by: ⎡

⎤ m −m 0 M = ⎣ 1 −1 m ⎦ 1 m −m Determine the values of m for which the determinant of M vanishes, i.e., | M |= 0. Solution The Maple commands det and fsolve are used to solve the problem as follows:



>

29

M:=matrix([[m,-m,0],[1,-1,m],[1,m,-m]]); ⎡ ⎤ m −m 0 M := ⎣ 1 −1 m ⎦ 1 m −m y:=det(M); y := −m2 − m3

>

fsolve(y,m); −1., 0., 0.

Problems 1.30 Define the following matrices using Maple: (a)

1 r A= 2 3 r r

(b) ⎡

⎤ 2 10 B = ⎣ −1 3 2 ⎦ −4 5 3 (c) an identity matrix C of size 6 × 6. (d) a zero matrix E of size 2 × 2. (e) a diagonal matrix F of size 4 × 4 where the diagonal elements are 1, 2, -1, 3. 1.31 Consider the matrix R given by ⎡

1 ⎢2 ⎢ B=⎢ ⎢x ⎣y 0

⎤ z −2 y − x xy 3 1 y3 x ⎥ ⎥ −1 1 xy z 2 ⎥ ⎥ 2 0 2 1⎦ 3 5 x2 5

Extract the following components of R using Maple:


30

Damage Mechanics (a) the element in row 2 and column 4. (b) the submatrix in rows 1 to 3 and columns 2 to 3. (c) the submatrix in rows 2 and 5 and columns 4 and 5. (d) the subvector in row 4 and columns 2, 4, 5, and 1 (exactly in the order given). (e) the subvector in column 3. (f) row 2. (g) column 5.

1.32 Determine, using Maple, the transpose, inverse, determinant, and trace of matrix X given by ⎡

⎤ 1 x −x X = ⎣ 2x 2 x ⎦ 1 0 x

1.33 Consider the two matrices M and N given by ⎡

⎤ 1x M = ⎣y 0⎦ xy

N=

1xy 0yx

Perform the following operations using Maple: (a) M + x − y (add the scalar quantity x-y to each element of M) (b) MN (c) N + MT (d) M + NT (e) (NM)−1



31

1.34 Solve the following system of equations using matrices and Maple. Use both methods of the inverse matrix and the Maple command linsolve independently. 3u + v − w = 0 u − v + 2w = 1 5u + 2v − 3w = −2

1.35 Determine using Maple the determinant and inverse of the following Jacobian matrix J where f (x, y) = x2 + y 2 and g(x, y) = sin(xy). ⎡

∂f ⎢ ∂x J = ⎣ ∂g ∂x

⎤ ∂f ∂y ⎥ ∂g ⎦ ∂y

1.36 Let A and v be defined as a matrix and a vector, respectively, as follows: ⎡

⎤ x2 y 2 0 A = ⎣ 1 xy −1 ⎦ 1 x y

⎡

⎤ 1 v = ⎣ −1 ⎦ 0 Determine the three products Av, vT A, and vT Av using Maple. 1.37 Determine the eigenvalues and eigenvectors for each one of the following matrices using Maple:


32

Damage Mechanics (a)

12 S= 34 (b)

⎡

⎤ 2 01 T = ⎣ −3 4 2 ⎦ −1 0 5

1.38 Determine the orthonormal basis for the following set of vectors using Maple: v1 = [1, −2, 3]T v2 = [0, 4, 5]T v3 = [2, 2, 7]T 1.39 Define two general square matrices P and Q, each of size 2×2, with their elements unspecified, using Maple. Perform the following operations using Maple: (a) (b) (c) (d) (e)

P−Q P−1 (PQ)T adjQ (use the result of Example 1.3) | P−1 Q |

1.40 Consider two general matrices A and B of size 2×3. Show that α(A + B) = αA + αB using Maple, where α is a scalar. 1.41 Consider two general matrices A and B of sizes 2×3 and 3×4, respectively. Show that (AB)T = BT AT using Maple. 1.42 Let A be a 2 × 2 matrix given by

10 A= 23 Determine A2 and

√ A using Maple.



33

1.43 Consider a 2 × 2 general matrix A. Show that (AT )−1 = (A−1 )T using Maple. 1.44 Three matrices A, B, and C are said to be linearly independent if the linear combination αA + βB + γC = 0 implies that the undetermined scalar coefficients α, β, and γ vanish, i.e. α = β = γ = 0. Are the following three matrices linearly independent? Use Maple. A=

11 11

10 B= 01

00 C= 11

1.45 A square matrix is said to be singular if its determinant vanishes. Give an example of a 3 × 3 singular matrix. 1.46 A matrix Q is said to be orthogonal if QT = Q−1 . Which of the following matrices is orthogonal? Use Maple. (a) Q=

cos θ sin θ − sin θ cos θ

(b)

cos θ sin θ Q= sin θ cos θ

1.47 Two matrices A and B are related by the equation A = P−1 BP where

−30 −48 A= 18 29


34

Damage Mechanics

B=

0 2 3 −1

Determine the matrix P using Maple. 1.48 Given a diagonal 3 × 3 matrix A as follows: ⎡

⎤ a1 0 0 A = ⎣ 0 a2 0 ⎦ 0 0 a3 Determine an expression for

√ A using Maple.

1.49 Show that the determinant of the product of two 3×3 general matrices is equal to the product of their determinants, i.e., | AB |=| A || B | for any two 3 × 3 general matrices A and B. Use Maple. 1.50 Let A be a square matrix of size n × n where n is a positive integer. Let v1 , v2 , ..., vn be the eigenvectors of A. Define the matrix P as follows: P = [v1 , v2 ...vn ] P is defined above as the matrix of eigenvectors. Then the product P−1 AP is a diagonal matrix. Diagonalize the matrix A given below using Maple: ⎡

⎤ 1 2 3 A = ⎣ −1 2 −1 ⎦ 2 3 4 1.51 The characteristic polynomial of a matrix A is defined by the determinant | λI − A | where λ is a scalar. Determine the characteristic polynomial of A given below using Maple: ⎡

⎤ 1 40 A = ⎣ −2 3 5 ⎦ 1 25



35

1.52 Use the definition of the characteristic polynomial in Problem 1.51 to show that every general matrix of size 2 × 2 is a zero of its characteristic polynomial. Use Maple. (This is called the Cayley-Hamilton Theorem in Linear Algebra where it applies to any general matrix of size n × n). 1.53 Use Maple and the definition of the characteristic polynomial in Problem 1.51 to show that the eigenvalues of a matrix are the roots of its characteristic polynomial. Consider a general 3 × 3 square matrix. 1.54 Let A be a 2 × 2 general square matrix as follows: A=

a11 a12 a21 a22

(a) Determine the two eigenvalues λ1 and λ2 of A. (b) Determine the inverse matrix A−1 . (c) Determine the two eigenvalues η1 and η2 of A−1 . 1 1 and η2 = (d) Show that η1 = λ1 λ2

1.4

Indicial Notation

In this section we introduce the indicial notation to be used throughout the book. The purpose of using indicial notation is to write compact equations that can easily be handled. Consider the variables x1 , x2 , x3 , ..., xn where n is a positive integer. The notation xi can be used to denote these variables where the subscript i (called an index) is free to take the values 1, 2, 3,..., n. Consider now the notation aij where indices i and j are free to take the values from 1 to n. The notation aij is used to denote the n × n variables a11 , a12 , ..., a1n , a21 , a22 , ..., a2n , ..., an1 , an2 , ann . In this book we will always use n = 3. Thus the notation xi will denote the three variables x1 , x2 , and x3 , while the notation aij will denote the nine variables a11 , a12 , a13 , a21 , a22 , a23 , a31 , a32 , and a33 . Consider now the following equation written in indicial notation: yi = aij xj


(1.10)

36

Damage Mechanics

It is noted that in each term of the equation, the index i appears only once. Note also that the index j is repeated twice in the term on the right hand side of the equation. A repeated index indicates summation over this index in the range of 1 to 3. Thus equation (1.10) is equivalent to the following equation: yi = Σ3j=1 aij xj

(1.11)

According to the Einstein summation convention, the summation sign, Σ, is dropped from the equation. Therefore, the notation of equation (1.10) will be used throughout the book. The following are the rules for the Einstein summation convention and indicial notation: 1. A repeated index indicates summation over this index in the range of 1, 2, and 3. The repeated index is called a dummy index because the letter used for this index can be replaced by any other letter. In this case, the summation sign, Σ, is dropped from the equation. 2. An index that appears only once in every term of the equation is called a free index. Each free index used indicates three separate equations when the free index takes each of the values 1, 2, and 3. 3. No index can be repeated more than twice using this indicial notation. If there is a summation over an index that is repeated three or more times, then the summation sign, Σ, must be used. We will now consider some examples illustrating the above three rules of indicial notation. According to Rule 1, equation (1.10) is equivalent to the following equation where the dummy index j is replaced first by m then by n: yi = aim xm = ain xn

(1.12)

The validity of equation (1.12) is made clear by retaining the summation sign and rewriting the equation as follows: yi = Σ3m=1 aim xm = Σ3n=1 ain xn

(1.13)

Next, we will write equation (1.10) explicitly in its expanded form as follows: yi = ai1 x1 + ai2 x2 + ai3 x3 (1.14) According to Rule 2 of the indicial notation, equation (1.10) actually represents three separate equations when the free index i takes each of the three values 1, 2, and 3. The three equations represented by equation (1.10) are:



37

y1 = a1j xj

(1.15a)

y2 = a2j xj

(1.15b)

y3 = a3j xj

(1.15c)

Next, we expand equations (1.15) further by summing over the dummy index (or use equation (1.14)) to obtain: y1 = a11 x1 + a12 x2 + a13 x3

(1.16a)

y2 = a21 x1 + a22 x2 + a23 x3

(1.16b)

y1 = a31 x1 + a32 x2 + a33 x3

(1.16c)

It should be noted that equations (1.16) are the expanded form of equation (1.10). According to Rule 3 of the indicial notation, the term xi yi zi has no significance and should not be used because the index i is repeated three times. In this case, the summation sign, Σ, should be retained and the term should be written as Σ3i=1 xi yi zi . The same rule applies to any index repeated more than twice. Consider now the following equation: w = λij ui uj

(1.17)

Equation (1.17) represents one equation only because there are no free indices in the terms of the equation. However, the term on the right side includes two dummy indices, i and j (each is repeated twice). Therefore, the right hand side can be expanded as follows. First, we expand the sum over i: w = λ1j u1 uj + λ2j u2 uj + λ3j u3 uj

(1.18)

Next, we expand each term on the right hand side of the equation (1.18) over j to obtain: w = λ11 u1 u1 + λ12 u1 u2 + λ13 u1 u3 + λ21 u2 u1 + λ22 u2 u2 + λ23 u2 u3 + λ31 u3 u1 + λ32 u3 u2 + λ33 u3 u3

(1.19)

It should be noted that equation (1.17) is exactly equivalent to the longer equation (1.19). In fact, equation (1.19) is the expanded form of equation (1.17). The Kronecker delta, δij , is defined by: δij =


1, i = j 0, i = j

(1.20)

38

Damage Mechanics

For example, δ11 = δ22 = δ33 = 1, and δ12 = δ23 = δ31 = 0. Therefore, δij can be represented by the 3 × 3 identity matrix as follows: ⎡

δij

⎤ 100 ≡ ⎣0 1 0⎦ 001

(1.21)

Note that δii = δ11 + δ22 + δ33 = 1 + 1 + 1 = 3. Next, we will explore the term δij aj . The index i is a free index; therefore the term δij aj represents three terms, namely δ1j aj , δ2j aj , and δ3j aj . Evaluating each term separately, we obtain: δ1j aj = δ11 a1 + δ12 a2 + δ13 a3 = (1)a1 + (0)a2 + (0)a3 = a1

(1.22a)

δ2j aj = δ21 a1 + δ22 a2 + δ23 a3 = (0)a1 + (1)a2 + (0)a3 = a2

(1.22b)

δ3j aj = δ31 a1 + δ32 a2 + δ33 a3 = (0)a1 + (0)a2 + (1)a3 = a3

(1.22c)

It is now clear from equation (1.22) that the following relation is true: δij aj = ai

(1.23)

Similarly, one can write nine equations to show that: δim Amj = Aij

(1.24)

The permutation symbol, ijk , has one of the values 0, 1, or -1 depending on the permutation formed by i, j, and k. The following are the three rules for the permutation symbol ijk : 1. If i, j, and k form an even permutation of 1, 2, and 3, then ijk = 1. For example, 123 = 231 = 312 = 1.



39

2. If i, j, and k form an odd permutation of 1, 2, and 3, then ijk = −1. For example, 132 = 321 = 213 = −1. 3. If i, j, and k do not form a permutation of 1, 2, and 3, then ijk = 0. For example, 111 = 122 = 223 = 0. Using the three rules above, it is clear that:

ijk = jki = kij = − jik = − kji = − ikj

(1.25)

Example 1.5 Show that equation (1.24) is true. Solution Equation (1.24) has two free indices, namely, i and j. Therefore, this equation represents nine equations as follows: δ1m Am1 = δ11 A11 + δ12 A21 + δ13 A31 = A11 δ1m Am2 = δ11 A12 + δ12 A22 + δ13 A32 = A12 δ1m Am3 = δ11 A13 + δ12 A23 + δ13 A33 = A13 δ2m Am1 = δ21 A11 + δ22 A21 + δ23 A31 = A21 δ2m Am2 = δ21 A12 + δ22 A22 + δ23 A32 = A22 δ2m Am3 = δ21 A13 + δ22 A23 + δ23 A33 = A23 δ3m Am1 = δ31 A11 + δ32 A21 + δ33 A31 = A31 δ3m Am2 = δ31 A12 + δ32 A22 + δ33 A32 = A32 δ3m Am3 = δ31 A13 + δ32 A23 + δ33 A33 = A33

(1.26)

It is clear from the equation above that δim Amj = Aij

Example 1.6 Given Aij = −Aji , show that Aij vi vj = 0. Solution We will start with 2Aij vi vj as follows: 2Aij vi vj = Aij vi vj + Aij vi vj = Aij vi vj + Aji vj vi = Aij vi vj + (−Aij )vj vi = Aij vi vj − Aij vi vj =0


(1.27)

40

Damage Mechanics

Therefore, Aij vi vj = 0 In the second line of equation (1.27) above, we interchanged indices i and j in the second term because they are both dummy indices. Also, in the fourth line of the equation we have used the commutative property of scalars vj vi = vi vj .

Example 1.7 Given Aij = −Aji and Bij = Bji , show that Aij Bij = 0. Solution We will start with 2Aij Bij as follows: 2Aij Bij = Aij Bij + Aij Bij = Aij Bij + Aji Bji = Aij Bij + (−Aij )Bij = Aij Bij − Aij Bij =0

(1.28)

Therefore, Aij Bij = 0. In the second line of equation (1.28) above, we interchanged indices i and j in the second term because they are both dummy indices.

Example 1.8 Let d be the determinant of a general 3 × 3 matrix A ≡ Aij . Show that d = ijk Ai1 Aj2 Ak3 Solution Let A be a 3 × 3 matrix given by: ⎡

⎤ A11 A12 A13 A = ⎣ A21 A22 A23 ⎦ A31 A32 A33 Then, the determinant d of A can be written as follows: A11 A12 A13 d =| A |= A21 A22 A23 A31 A32 A33



41

= A11 (A22 A33 − A23 A32 ) − A12 (A21 A33 − A23 A31 ) + A13 (A21 A23 − A22 A31 ) = A11 A22 A33 + A12 A23 A31 + A13 A21 A32 − A11 A23 A32 − A12 A21 A33 − A13 A31 A22 = 123 A11 A22 A33 + 312 A31 A12 A23 + 231 A21 A32 A13 + 132 A11 A32 A23 + 213 A21 A12 A33 + 321 A31 A22 A13 = ijk Ai1 Aj2 Ak3

Problems 1.55 Given that Aij is represented by the following matrix: ⎡ ⎤ 2 −3 0 Aij ≡ ⎣ 4 4 1 ⎦ −2 2 5 Determine the following quantities: (a) Aii (b) Aij Aij (c) Aij Aji (d) δii Amm (e) Apq Apq 1.56 Write explicitly the three equations represented by the following equation: vm = Qmn un

1.57 Write explicitly the nine equations represented by the equation: Aij = Bir Crj

1.58 How many equations are represented by the following equation. Write the expanded result explicitly. S = vi Qij vj


(1.29)

42

Damage Mechanics

1.59 Write the following three equations as one single equation using indicial notation: dy1 =

∂y1 ∂y1 ∂y1 dx1 + dx2 + dx3 ∂x1 ∂x2 ∂x3

dy2 =

∂y2 ∂y2 ∂y2 dx1 + dx2 + dx3 ∂x1 ∂x2 ∂x3

dy3 =

∂y3 ∂y3 ∂y3 dx1 + dx2 + dx3 ∂x1 ∂x2 ∂x3

1.60 Given that ui , vi , and Aij are represented by the following two vectors and matrix: ⎡

⎤ 1 ui ≡ ⎣ −1 ⎦ 0

⎡

⎤ 2 vi ≡ ⎣ 3 ⎦ −5

⎡

⎤ 4 2 −1 Aij ≡ ⎣ −3 3 0 ⎦ 5 1 2 Determine the vectors or matrices represented by the following quantities: (a) wk = ijk ui vj (b) yi = ijk Ajk (c) Bij = ijk uk + ijl vl (d) the scalar quantity Aij ui vj 1.61 Given that Bij = αAij + βδij , where α and β are scalars. Show that:



43

(a) Bij Aij = αAij Aij + βAmm (b) Bij Bij = α2 Aij Aij + 2αβAmm + 3β 2 1.62 Show that the following identity holds between the Kronecker delta and the permutation symbol:

ijk ipq = δjp δkq − δjq δkp

1.63 Show that the following relations hold: (a) ipq jpq = 2δij (b) ijk ijk = 6 (Hint : Use the result of Problem 1.62 above). 1.64 Prove the following relations: (a) δmn δmn = 3 (b) ijk uj uk = 0 (c) δim δmj = δij (d) ijk δij = 0 1.65 Prove the following relation involving determinants: Aip Aiq Air Ajp Ajq Ajr = ijk pqr |A| Akp Akq Akr where |A| is the determinant of a general 3 × 3 matrix A. Use this result to solve Problem 1.62 above directly. 1.66 Let A be a general 3 × 3 matrix whose elements are given by Aij . The minor Mij of an element Aij is defined as the determinant of the matrix formed by deleting the ith row and the jth column of A. The corresponding cofactor Cij is defined by Cij = (−1)i+j Mij . Show that the following two relations hold: (a) Apj Cij =| A | δpi (b) Aip Cij =| A | δpj


44

Damage Mechanics

1.5

Transformation of Vectors

Let e1 , e2 , and e3 be three unit vectors along the x, y, and z coordinates, respectively (see Figure 1.7). Obviously, these unit vectors are perpendicular to each other so that e1 · e1 = 1, e1 · e2 = 0, etc. These relations are written using indicial notation as follows:

y

e2

e1 x e3

z

FIGURE 1.7 Unit vectors e1 , e2 , and e3 .

ei · ej = δij

(1.30)

Let u and v be two vectors such that u = u 1 e1 + u 2 e2 + u 3 e3

(1.31a)

v = v1 e1 + v2 e2 + v3 e3

(1.31b)



45

Equations (1.31) can be written using indicial notation as follows: u = u i ei

(1.32a)

v = vi ej

(1.32b)

Next, consider the dot product u · v. Using equations (1.30) and (1.32), we obtain: u · v = ui vj δij = ui vi

(1.33)

The three unit vectors have the property that e1 ×e2 = e3 , e2 ×e3 = e1 , and e1 × e1 = 0, etc. This property can be written using indicial notation as follows: ei × ej = ijk ek

(1.34)

Consider now the cross product u×v. Using equations (1.32) and (1.34), we obtain: u × v = ijk ui vj ek

(1.35)

Next, consider a tranformation T which transforms the vector u into the vector v. This can be written as follows: T(u) = v

(1.36)

In general, the transformation T can be represented by a 3 × 3 matrix. For example, if u = v, then T would be represented by the identity matrix I. Let v1 and v2 be two vectors in three-dimensional space. Suppose that a transformation T, when applied to v1 and v2 , satisfies the following two properties of vector addition and scalar multiplication: T(v1 + v2 ) = T(v1 ) + T(v2 )

(1.37a)

T(αv1 ) = αT(v1 )

(1.37b)

where α is a scalar. In this case, T is called a linear transformation. Next, we will explore how to determine the components of vectors and linear transformations. Suppose that u and v are two vectors related by the linear transformation T as before, i.e., v = T(u). Taking the dot product of the vector u with any of the unit vectors e1 , e2 , or e3 will result in the component of the vector along the respective coordinate axis. For example, u · e1 = u1 , u · e2 = u2 , and u · e3 = u3 . These equations can be written using indicial notation as follows (see Figure 1.8):


46

Damage Mechanics y

u

e1

x

u1 = u . e 1

z

FIGURE 1.8 Projection of vector u on the x-axis.

u i = u · ei

(1.38)

The components of the vector u can be obtained using equation (1.38) above. Next, we determine the components of the vector v and the linear transformation T. Substituting equations (1.32a) into equations (1.36), we obtain: u = T(u) = T(ui ei = T(u1 e1 + u2 e2 + u3 e3 ) = u1 T(e1 ) + u2 T(e2 ) + u3 T(e3 )

(1.39)

In deriving the last line of equation (1.39) above, we have used the fact that T is a linear transformation and applied both equations (1.37) simultaneously, where u1 , u2 , and u3 are scalars. Equation (1.39) can be written using indicial notation as follows: v = uj T(ej )


(1.40)


47

The components of vector v are written now using the dot product as shown in equation (1.38) but replacing u with v. vi = v · ei = uj T(ej ) · ei

(1.41)

In deriving equation (1.41), we have used equations (1.40) and the commutative property of the dot product. The dot product T(ej ) · ei is the component of the vector T(ej ) along the direction of ei . We will denote this component by Tij . Therefore, we have the following equation (by definition): Tij = T(ej ) · ei

(1.42)

The components of the linear transformation T are obtained using equation (1.42) above. It is clear that T has nine components since equation (1.42) has two free indices and thus represents nine equations. Finally, the components of vector v are obtained by substituting equation (1.42) into equation (1.41): vi = Tij uj

(1.43)

The linear transformation T can be represented by a 3 × 3 matrix since equation (1.43) can be represented in matrix form as follows: ⎤ ⎡ ⎤⎡ ⎤ T11 T12 T13 u1 v1 ⎣ v2 ⎦ = ⎣ T21 T22 T23 ⎦ ⎣ u2 ⎦ v3 T31 T32 T33 u3 ⎡

(1.44)

It is clear from equations (1.42) and (1.44) that T11 , T21 , and T31 are the components of T(e1 ). Therefore, the vector T(e1 ) can be written as follows: T(e1 ) = Tj1 ej

(1.45)

The same relation holds for the vectors T(e2 ) and T(e3 ). Therefore, equation (1.45) is generalized as follows: T(ei ) = Tji ej

(1.46)

Example 1.9 A linear transformation T transforms every vector u in three-dimensional 1 space into a vector v such that v = u. Determine the matrix represented 3 by T.


48

Damage Mechanics

Solution We have the following relations: 1 T(e1 ) = ( )e1 + (0)e2 + (0)e3 3 1 T(e2 ) = (0)e1 + ( )e2 + (0)e3 3 1 T(e3 ) = (0)e1 + (0)e2 + ( )e3 3 Using equations (1.46), we obtain the matrix representation of T as follows: ⎤ 0 0 1 T ≡ ⎣ 0 13 0 ⎦ = I 3 0 0 13 ⎡1 3

Example 1.10 Let T be a constant transformation that transforms every vector in threedimensional space into the vector e1 +e2 +e3 . Is T a linear transformation? If yes, find the matrix representation of T. Solution Let u and v be two arbitrary vectors in three dimensional space. Then, we have the following relations: T(u) = e1 + e2 + e3 T(v) = e1 + e2 + e3 We need to check if equations (1.37) hold. T(u + v) = e1 + e2 + e3 T(u) + T(v) = 2(e1 + e2 + e3 ) Thus it is clear that T(u + v) = T (u) + T (v). Therefore, T is not a linear transformation.



49

Problems 1.67 Given a = 2e1 − e2 + 2e3 and b = e + 4e3 , determine the products a · b and a × b using equations (1.33) and (1.35), respectively. 1.68 Given the vector u = e1 − 3e2 + 5e3 and the linear transformation T represented by the matrix: ⎡

⎤ 1 −2 0 T ≡ ⎣ −3 5 2 ⎦ 4 3 1 Determine the vector v = T(u). 1.69 Consider the linear transformation T represented by the matrix ⎤ −3 1 0 T ≡ ⎣ 4 −2 3 ⎦ 1 4 5 ⎡

What are the three components of the vector T(e2 ). 1.70 Let T be a linear transformation that transforms every vector u into a vector v given by v = (u · a)b where a and b are given by: a = e1 + e2 + e3 b = 2e1 − e2 + e3 Determine the matrix representation of T. 1.71 Let T be a transformation defined by T(u) = αu − e1 where α is a scalar. Is T a linear transformation? If yes, determine the matrix representation of T. 1.72 A linear transformation T is represented by the following matrix: ⎡

⎤ 1 1 2 T ≡ ⎣ −2 3 5 ⎦ 4 −2 5 Determine the vectors T(e1 ) and T(2e1 − e2 + e3 ). 1.73 Let e1 and e2 be two unit vectors along the coordinate axes x and y in two-dimensional space. Let R be a transformation that rotates every vector counterclockwise by an angle θ.


50

Damage Mechanics (a) Show that R is a linear transformation. (b) Determine the 2 × 2 matrix representation of R.

1.74 Solve Problem 1.21 again using equations (1.33) and (1.35). 1.75 Solve Problem 1.22 again using equations (1.33) and (1.35).

1.6

Cartesian Tensors

A linear transformation as defined in Section 1.5 is called a second-order tensor. In this section we will study general tensors including second-order tensors. The discussion will be limited to three-dimensional rectangular coordinates and Cartesian tensors. Maple has a special package called the Tensor Package that is invoked with the following command: >

with(tensor);

[Christoffel1 , Christoffel2 , Einstein, Jacobian, Killing eqns, Levi Civita, Lie diff , Ricci , Ricciscalar , Riemann, RiemannF , Weyl , act , antisymmetrize, change basis, commutator , compare, conj , connexF , contract, convertNP , cov diff , create, d1metric, d2metric, directional diff , displayGR, display allGR, dual , entermetric, exterior diff , exterior prod , frame, geodesic eqns, get char , get compts, get rank , init , invars, invert , lin com, lower , npcurve, npspin, partial diff , permute indices, petrov , prod , raise, symmetrize, tensorsGR, transform] Since second-order tensors can be represented by matrices, the Linear Algebra Package in Maple can be used also for second-order tensors. However, the Tensor Package should be used for general tensors. An orthogonal tensor is a tensor whose inverse is equal to its transpose (see Example 1.11). Let Q be an orthogonal second-order tensor given by the following transformation: ei = Qmi em ei

(1.47)

where is a transformed coordinate system that can be obtained from em by a combination of a rotation and a reflection (see Figure 1.9). Equation (1.47) can be represented by the following matrix equation: ⎤⎡ ⎤ ⎡ ⎤ ⎡ Q11 Q12 Q13 e1 e1 ⎣ e2 ⎦ = ⎣ Q12 Q22 Q23 ⎦ ⎣ e2 ⎦ (1.48) e3 Q13 Q23 Q33 e3



51

e2 e2'

e1'

e1

e3

e3' FIGURE 1.9 Coordinate systems em and ei . Since the matrix Q is orthogonal, we have Q−1 = QT . Therefore, we have the following relation: QQT = QT Q = I

(1.49)

Equation (1.49) can be written using indicial notations as follows: Qim Qjm = Qmi Qmj = δij

(1.50)

The components of Q are obtained using equation (1.42) as follows: Qmi = Q(ei ) · em

(1.51)

However, Q(ei ) = ei (see equation (1.47)). Therefore, equation (1.51) becomes:


52

Damage Mechanics Qmi = ei · em = cos(ei , em )

(1.52)

cos(ei , em )

ei

where is the cosine of the angle between the vectors and em . We will now consider how the components of a general vector v in the coordinate system em transform to the coordinate system ei . The components of v can be written in each coordinate system using equation (1.38) as follows: vm = v · em vi

=v·

(1.53a)

ei

(1.53b)

Substituting equation (1.47) into equation (1.53b) and comparing with equation (1.53a), we obtain: vi = Qmi vm

(1.54)

Equation (1.54) can be written in matrix form as follows: v = QT v

(1.55)

When using equation (1.55), it should be noted that v is the vector with respect to the coordinate system em while v is the same vector with respect to the coordinate system ei . Equations (1.54) and (1.55) represent the general transformation law for any vector v. Next, we will consider how the components of a general second-order tensor T in the coordinate system em transform to the coordinate system ei . The components of T can be written in each coordinate system using equation (1.42) as follows: Tmn = T (en ) · em Tij

=

T (ej )

·

(1.56a)

ei

(1.56b)

Substituting equation (1.47) into equation (1.56b) we obtain: Tij = T (Qnj · en ) · Qmi em = Qmi Qnj T (en ) · em

(1.57)

Comparing equations (1.56a) and (1.57), we obtain: Tij = Qmi Qnj Tmn

(1.58)

Equation (1.58) can be written in matrix form as follows: T = QT TQ

(1.59)

When using equation (1.59), it should be noted that T represents the tensor with respect to the coordinate system ei (or ej ), while T represents



53

the same tensor with respect to the coordinate system em (or en ). Equations (1.58) and (1.59) represent the general transformation law for any second-order tensor T. In general, a scalar c is considered a zeroth-order tensor with the transformation law: c = c

(1.60a)

A vector v is considered a first-order tensor with the transformation law: vi = Qmi vm

(1.60b)

A second-order tensor T (usually called just a tensor) has the transformation law: Tij = Qmi Qnj Tmn

(1.60c)

Continuing along the same line, a third-order tensor L has the transformation law: Lijk = Qmi Qnj Qpk Lmnp

(1.60d)

A fourth-order tensor M will have the following transformation law: Mijkl = Qmi Qnj Qpk Qql Mmnpq

(1.60e)

Higher-order tensors can be defined using a transformation law along the lines of equations (1.60).

Example 1.11 Let Q be an orthogonal second-order tensor. Show that for any two general vectors u and v, the following relation holds: Q(u) · Q(v) = u · v Solution Since Q is orthogonal, we have: QT Q = I I − QT Q = 0 (I − QT Q)(u) = 0


54

Damage Mechanics v · (I − QT Q)(u) = 0 v · I(u) = v · (QT Q)(u) v · u = v · QT (Q(u)) v · u = Q(v) · Q(u)

Example 1.12 Let Q be an orthogonal second-order tensor. Show that |Q| = ±1, where |Q| is the determinant of Q. Solution Since Q is orthogonal, we have: QQT = I |QQT | = |I| |Q||QT | = 1 but |Q| = |QT | |Q||Q| = 1 |Q|2 = 1 |Q| = ±1

Example 1.13 Suppose that v is a vector and T is a second-order tensor related by the equation vi = Aijk Tjk Show that Aijk are the components of a third-order tensor.


(1.61)


55

Solution Since v is a vector, it transforms according to the relation (see equation (1.60b)): vi = Qmi vm

(1.62a)

Pre-multiply both sides of equation (1.62a) by Qni and noting that Qni Qmi = δnm , we obtain: Qni vi = δnm vm = vn

(1.62b)

Switching indices in equation (1.62b), we obtain: vi = Qin vn

(1.63)

Since T is a second-order tensor, we have the following relation (see equation (1.60c)): Tij = Qmi Qni Tmn (1.64a) Pre-multiplying equation (1.64a) by Qpi Qqj , we obtain: Qpi Qqj Tij = Qpi Qqj Qmi Qnj Tmn = δpm δqn Tmn = Tpq

(1.64b)

Switching indices (using jk for pq and mn for ij) in equation (1.64b), we obtain: Tjk = Qjm Qkn Tmn

(1.65)

Next, substitute equations (1.63) and (1.65) into equation (1.61) to obtain: Qin vn = Aijk Qjm Qkn Tmn

(1.66a)

Pre-multiply equation (1.66a) by Qir : Qir Qin vn = Qir Qjm Qkn Aijk Tmn

(1.66b)

Substituting Qir Qin = δrn , equation (1.66b) becomes: vr = (Qir Qjm Qkn Aijk )Tmn = Armn Tmn

where


(1.67)

56

Damage Mechanics

Armn = Qir Qjm Qkn Aijk

(1.68)

It should now be clear from equation (1.68) that Aijk are the components of a third order tensor (see equation (1.60d)).

Example 1.14 A second-order tensor T is symmetric if Tij = Tji , or equivalently, T = TT . On the other hand, a tensor T is antisymmetric if Tij = −Tji , or equivalently, T = −TT . Suppose that three second-order tensors A, B, and C are related by C = A + B, where A=

1 (C + CT ) 2

(1.69a)

B=

1 (C − CT ) 2

(1.69b)

Show that A is symmetric tensor (called the symmetric part of C) and B is an antisymmetric tensor (called the antisymmetric part of C). Solution Determine the transpose of both A and B as follows: 1 1 (C + CT )T = (CT + (CT )T ) 2 2 1 1 = (CT + C) = (C + CT ) 2 2

AT =

= A

Therefore, A is a symmetric tensor. 1 1 (C − CT )T = (CT − (CT )T ) 2 2 1 1 = (CT − C) = − (C − CT ) 2 2 = −B

BT =

Therefore, B is an antisymmetric tensor.



57

Problems 1.76 Let T be a second-order tensor that has the following matrix representation with respect to e1 , e2 , and e3 : ⎡

⎤ 5 −2 0 T ≡ ⎣0 1 4⎦ 3 2 3 Suppose that the primed coordinate axes e1 , e2 , and e3 are obtained by rotating every vector about e3 by an angle of 45◦ counterclockwise. Determine the matrix representation T of T in the primed coordinate axes. 1.77 Let A and B be two second-order tensors related by the equation Bij = Cijkl Akl . Show that Cijkl are the components of a fourthorder tensor. 1.78 Let Tij be the components of a second-order tensor T. Show that Tii is a scalar invariant, i.e., show that Tii = Tmm with respect to any orthogonal transformation. 1.79 Check the result given in Problem 1.78 by using the example given in and show that they Problem 1.76, i.e., determine both Tii and Tmm are equal. 1.80 Let Tij be the components of a second-order tensor T. Show that Tij Tij is a scalar invariant, i.e., Tij Tij = Tmn Tmn for any orthogonal transformation. 1.81 Check the results given in Problem 1.80 by using the following matrix representations for the tensor T and the orthogonal transformation Q: ⎡

⎤ 1 0 −2 T ≡ ⎣5 2 4 ⎦ 31 3 ⎡

⎤ 100 Q ≡ ⎣1 0 1⎦ 010 Tmn and show where ei = Q(ei ). Determine both Tij Tij and Tmn that they are equal.


58

Damage Mechanics

1.82 Let T be a second-order tensor represented by the following matrix: ⎡

⎤ 3 1 10 T ≡ ⎣ −2 5 0 ⎦ 3 5 7 Determine the matrix representations of both the symmetric part and the antisymmetric part of T. (Hint : Use Example 1.14) 1.83 Let Eijkl be the components of a fourth-order tensor. Show that Eijmm are the components of a second-order tensor. 1.84 Let Aij and Bij be the components of second-order tensors A and B, respectively. Show that the product Aim Bmj are the components of a second-order tensor. 1.85 Let Tijpq = αδij δpq + βδip δjq where α and β are scalars. Show that Tijpq are the components of a fourth-order tensor. 1.86 Let R be a symmetric second-order tensor that is nonsingular, i.e., it has an inverse R−1 . Show that R−1 is also symmetric. 1.87 The dyadic product uv of two vectors u and v is defined by (uv)(w) = (v · w)u for any vector w. (a) Show that uv is a second order tensor. (b) Show that (uv)ij = ui vj . (c) Determine the matrix representation of uv. 1.88 The transpose TT of a second-order tensor T is defined by the relation T u · T(v) = v · TT (u) for any vectors u and v. Show that (PQ) = QT PT for any two second-order tensors P and Q. 1.89 Let A be an antisymmetric tensor. We can find a vector u such that A(v) = u × v for any arbitrary vector v. The vector u is called the dual vector or the axial vector of A. Show that u = − 21 ijk Ajk ei . 1.90 Let T be a second-order tensor represented by the following matrix: ⎡

⎤ 4 11 T = ⎣ −3 2 5 ⎦ 4 10



59

(a) Determine the antisymmetric part of T, denoted by TA . (b) Determine the axial vector of TA (see Problem 1.89). (c) Check that TA (v) = u × v for v = e1 + e2 + e3 . 1.91 Let u and v be two vectors. Show that ui vi is a scalar invariant, i.e., for any orthogonal transformation. show that ui vi = um vm 1.92 Show that the determinant of a matrix is a scalar invariant, i.e., show that |T| = |T | where T is the matrix of tensor T with respect to e1 , e2 , and e3 , and T is the matrix of T with respect to e1 , e2 , and e3 . 1.93 Let T be a second-order tensor and let A and B be the symmetric and antisymmetric parts of T, respectively. Show that u·T(u) = u·A(u) for any vector u, i.e., u · B(u) = 0. 1.94 Let S be a symmetric second-order tensor. Show that ijk Sjk = 0 where ijk is the permutation symbol. 1.95 An isotropic tensor is a tensor which has the same set of components in all coordinate systems. (a) Show that all scalars are isotropic tensors. (b) Any second-order isotropic tensor can be written as αI where α is a scalar and I is the identity matrix. 1.96 Show that there are no nontrivial first-order isotropic tensors (use the definition in Problem 1.95). 1.97 Show that any fourth-order isotropic tensor T can be written in component form as follows:

Tijmn = α(δij δmn ) + β(δim δjn + δin δjm ) + γ(δim δjn − δin δjm ) where α, β, and γ are scalars (use the definition in Problem 1.95). 1.98 Let Mij and Nij be components of second-order tensors M and N, respectively. Suppose Mij and Nij are related by the relation Mij = Pijmn Nmn . Show that if Mij is symmetric, then Pijmn = Pjimn. 1.99 Let M, N, and P be related by the same relation given in Problem 1.98, i.e., Mij = Pijmn Nmn . Show that if N is symmetric and P is isotropic, then Mij = 2αNij + βNkk δij where α and β are scalars.


60

1.7

Damage Mechanics

Eigenvalues and Eigenvectors of Tensors

Eigenvalues and eigenvectors are defined for second-order tensors in a similar way to their definition for matrices as described in section 1.3. Therefore, for any second-order tensor T, the scalar λ is called an eigenvalue of the tensor if T(V) = λv for any arbitrary vector v. The vector v is called an eigenvector of T. Usually eigenvectors are normalized as unit vectors. Let n be a unit eigenvector of the tensor T, then T(n) = λn = λI(n). Therefore, we have the following equation: (T − λI)n = 0

(1.70)

Equation (1.70) can be solved only if the determinant of the tensor T−λI vanishes: |T − λI| = 0

(1.71)

For a second-order tensor T, equation (1.71) is a cubic polynomial equation in λ – called the characteristic polynomial of T. The three roots of the characteristic polynomial are the eigenvalues of the tensor T. The eigenvalues of a tensor are also called the principal values of the tensor, while the eigenvectors are called the principal directions of the tensor. The characteristic polynomial of a tensor T as given in equation (1.71) can be written explicitly as follows: λ3 − I1 λ2 + I2 λ − I3 = 0

(1.72)

where I1 , I2 , and I3 are called the scalar invariants of T, given by: I1 = Tii 1 I2 = (Tii Tjj − Tij Tji ) 2 I3 = |T|

(1.73)

It should be noted that the scalar invariants of T remain unchanged regardless of the base vectors or coordinate system used.

Example 1.15 Let T be a second-order real symmetric tensor. Show that if the eigenvalues of T are all distinct, then the principal directions of T are mutually perpendicular.



61

Solution Let λ1 and λ2 be two distinct eigenvalues (i.e. λ1 = λ2 ) of T with the corresponding eigenvectors n1 and n2 . Then we have the following two equations:

T(n1 ) = λ1 n1 T(n2 ) = λ2 n2

(1.74)

Multiply (dot product) the first equation of (1.74) with n2 and multiply (dot product) the second equation of (1.74) with n1 to obtain: n2 · T(n1 ) = n2 · λ1 n1 n1 · T(n2 ) = n1 · λ2 n2

(1.75)

However, n1 · T(n2 ) = n2 · TT (n1 ) = n2 · T(n1 ) since T is symmetric. Therefore, the two equations (1.75) are identical so that we have: n2 · λ1 n1 = n1 · λ2 n2

(1.76)

Equation (1.76) can be re-written as follows: (λ1 − λ2 )(n1 · n2 ) = 0

(1.77)

Since λ1 = λ2 , we conclude that n1 ·n2 = 0 and thus the two eigenvectors n1 and n2 are mutually perpendicular.

Example 1.16 Let T be a second-order real symmetric tensor and n1 , n2 , and n3 be three unit vectors along the principal directions of T, which are mutually perpendicular. Let λ1 , λ2 , λ3 be the corresponding eigenvalues. (a) Show that the tensor T can be represented along the principal directions with a diagonal matrix of the form: ⎡

⎤ λ1 0 0 T ≡ ⎣ 0 λ2 0 ⎦ 0 0 λ3


62

Damage Mechanics

(b) Show that, in this case, the scalar invariants of T are given by: I1 = λ1 + λ2 + λ3 I2 = λ, λ2 + λ2 λ3 + λ3 λ1 I3 = λ1 λ2 λ3 Solution (a) In order to determine the matrix representation of T, we use equation (1.42) as follows: T11 T12 T13 T21 T22 T23 T31 T32 T33

= T(n1 ) · n1 = T(n2 ) · n1 = T(n3 ) · n1 = T(n1 ) · n2 = T(n2 ) · n2 = T(n3 ) · n2 = T(n1 ) · n3 = T(n2 ) · n3 = T(n3 ) · n3

= λ1 n1 · n1 = λ2 n2 · n1 = λ3 n3 · n1 = λ1 n1 · n2 = λ2 n2 · n2 = λ3 n3 · n2 = λ1 n1 · n3 = λ2 n2 · n3 = λ3 n3 · n3

= λ1 =0 =0 =0 = λ2 =0 =0 =0 = λ3

Therefore, we have; ⎤ λ1 0 0 T ≡ ⎣ 0 λ2 0 ⎦ 0 0 λ3 ⎡

(b) Using equations (1.73) for the scalar invariants and applying them to the diagonal matrix above, we obtain: I1 = Tii = λ1 + λ2 + λ3 I2 = 12 (Tii Tjj − Tij Tji ) First calculate Tij Tji :

Tij Tji = T1j Tj1 + T2j Tj2 + T3j Tj3 = T11 T11 + T12 T21 + T13 T31 + T21 T12 + T22 T22 + T23 T32 + T31 T13 + T32 T23 + T33 T33 = λ21 + λ22 + λ23



63

1 (λ1 + λ2 + λ3 ) (λ1 + λ2 + λ3 ) − λ21 + λ22 + λ23 2 1 2 = λ1 + 2λ1 λ2 + 2λ1 λ3 + λ22 + 2λ2 λ3 + λ23 − λ21 − λ22 − λ23 2 = λ1 λ2 + λ2 λ3 + λ3 λ1 λ2 0 −0+0 I3 = |T| = λ1 0λ3 I2 =

= λ1 λ2 λ3

(1.78)

Example 1.17 Let T be a second-order real symmetric tensor represented by the following matrix with respect to some particular coordinate system: ⎡ ⎤ 3 −1 0 T ≡ ⎣−1 2 5⎦ 0 5 2 Determine the eigenvalues and the corresponding eigenvectors of T. Solution Applying equation (1.71), we obtain: 3 − λ −1 0 |T − λI| = −1 2 − λ 5 = 0 0 5 2 − λ −1 5 2 − λ 5 =0 +1 (3 − λ) 0 2 − λ 5 2 − λ (3 − λ)[(2 − λ)2 − 25] + λ − 2 = 0 Simplifying the above equation, we obtain: λ3 − 7λ2 − 10λ + 66 = 0 The three roots of the above cubic equation are the eigenvalues of T given by: λ1 = −3.1 λ2 = −3.0 λ3 = −7.1


64

Damage Mechanics

The eigenvectors are then obtained by substituting each λ obtained into equation (1.70) and solving for n in each case. Therefore, the three eigenvectors are obtained as follows: n1 ≡ [0.11640.7080 − 0.6965]T n2 ≡ [−0.9784 − 0.0390 − 0.2032]T n3 ≡ [0.1710 − 0.7051 − 0.6882]T

Problems 1.100 Determine the eigenvalues and the corresponding eigenvectors for the second-order tensor T which is represented by the following matrix with respect to some particular coordinate system: ⎡

⎤ 101 T ≡ ⎣0 2 0⎦ 103 1.101 Let T be a second-order real and symmetric tensor. Show that the eigenvalues of T include the maximum and minimum values that the diagonal elements of any matrix representation of T can have. 1.102 Consider the tensor T given in the Example 1.17. Determine the scalar invariants of T and find the eigenvalues using equation (1.72). 1.103 Let T be a second-order tensor represented by the following matrix with respect to some particular coordinate system: ⎡

⎤ 10 0 T ≡ ⎣0 2 3 ⎦ 0 3 −2 Can the tensor T be represented by the following matrix with respect to some other coordinate system (Hint : Use eigenvalues): ⎡

⎤ 1 −1 0 ⎣−1 0 5⎦ 0 5 2



65

1.104 Let T be a second-order tensor represented by the following matrix with respect to some particular coordinate system: ⎡

⎤ 12 2 T ≡ ⎣2 3 5 ⎦ 2 5 −1 Determine the diagonal matrix representation of T given in Example 1.16. 1.105 Show that the three scalar invariants I1 , I2 , and I3 of equations (1.73) are scalars. 1.106 Determine the eigenvalues and eigenvectors of an antisymmetric tensor T represented by the following matrix with respect to some particular coordinate system: ⎡

⎤ 0 01 T ≡ ⎣ 0 0 0⎦ −1 0 0 1.107 Consider the antisymmetric tensor T of Problem 1.106 above. Show that the eigenvectors corresponding to nonzero eigenvalues satisfy v · v = 0. Show also that this property holds for all antisymmetric tensors. 1.108 Solve Example 1.17 again using Maple. 1.109 Solve Problem 1.100 again using Maple. 1.110 Solve Problem 1.103 again using Maple. 1.111 Solve Problem 1.104 again using Maple. 1.112 Solve Problem 1.106 again using Maple.

1.8

Tensor Calculus

In this section we study tensor functions of second-order tensors including tensor differentiation and integration. Let T(t) be a tensor-valued function of a scalar t. We will denote T(t) here by just T. The tensor derivative dT/dt is a tensor defined by:


66

Damage Mechanics dT T (t + ∆t) − T (t) lim = ∆t → 0 dt ∆t

(1.79)

The following identities related to the tensor derivative can be easily proved: d (T + S) dt d (α (t) T) dt d (TS) dt d (T (a)) dt

dT dS + dt dt dα dT = T+α dt dt dT dS = S+T dt dt da dT = (a) + T dt dt T dT d T T = dt dt =

(1.80a) (1.80b) (1.80c) (1.80d) (1.80e)

In the above equations, T and S are second-order tensors, a is a vector, and α (t) is a scalar function. Let Φ (r) be a scalar-valued function of the position vector r, i.e., Φ (r) is a scalar field. Define the gradient of Φ, defined as a vector, denoted by ∇Φ as follows: ∇Φ · dr = dΦ = Φ (r + dr) − Φ (r)

(1.81)

Dividing the above equation by dr (the magnitude or length of dr), we obtain:

dΦ dr

= ∇Φ · e

(1.82)

in e−direction

where e = dr/dr is a unit vector along dr. Equation (1.81) means that the rate of change of Φ along dr (the directional derivative) is equal to the component of ∇Φ in the direction of e. Applying equation (1.81) along each of the e1 , e2 , and e3 directions, we obtain:

dΦ dr dΦ dr

=

∂Φ = ∇Φ · e1 = (∇Φ)1 ∂x1

(1.83a)

=

∂Φ = ∇Φ · e2 = (∇Φ)2 ∂x2

(1.83b)

in e1 −direction

in e2 −direction



dΦ dr

67

= in e3 −direction

∂Φ = ∇Φ · e3 = (∇Φ)3 ∂x3

(1.83c)

Thus the vector ∇Φ can be written in terms of its components as follows: ∇Φ =

∂Φ ∂Φ ∂Φ ∂Φ ei = e1 + e2 + e3 ∂xi ∂x1 ∂x2 ∂x3

(1.84)

Geometrically, the gradient vector bf ∇Φ is normal to the surface of constant Φ because in this case dΦ = 0 for any dr tangent to the surface. Thus ∇Φ · dr = 0 and ∇Φ is normal to the tangent to the surface. Let v (r) be a vector-valued function of the position vector r, i.e. v(r) is a vector field. We define the gradient of v, a second-order tensor, denoted by ∇v as follows: (∇v) (dr) = dv = v (r + dr) − v(r)

(1.85)

Dividing the above equation by dr (the length of dr), we obtain: dv = (∇v) (e) (1.86) dr in e−direction where e = dr/dr is a unit vector along dr. Next, we will obtain the components of the gradient tensor ∇v as follows: (∇v)11 = e1 · (∇v) (e1 ) = e1 ·

∂v ∂ ∂ ∂v1 = (e1 · v) = (1.87) v1 = ∂x1 ∂x1 ∂x ∂x1

In general,

(∇v)ij = ei · (∇v) (ej ) = ei ·

∂v ∂ ∂vi = (ei · v) = ∂xj ∂xj ∂xj

(1.88)

Thus, the second-order gradient tensor ∇v may be represented by the following matrix: ⎤ ⎡ ∂v1 ∂v1 ∂x2 ∂v2 ∂x2 ∂v3 ∂v3 ∂x1 ∂x2

1 ⎢ ∂x ∂v2 ∇v ≡ ⎣ ∂x 1

∂v1 ∂x3 ∂v2 ⎥ ∂x3 ⎦ ∂v3 ∂x3

(1.89)

Let v(r) be a vector field as defined above. The divergence of v(r), denoted by div v, is defined to be a scalar field as follows: divv = tr (∇v)


(1.90)

68

Damage Mechanics

where tr is the trace of a second-order tensor. Substituting equation (1.88) into equation (1.89), we obtain: ∂v2 ∂v3 ∂vi ∂v1 + + = (1.91) ∂x1 ∂x2 ∂x3 ∂xi Let T(r) be a second-order tensor-valued function of the position vector r, i.e., T(r) is a tensor field. The divergence of T, denoted by div T, is a vector field defined by: divv =

(divT) · a = div(TT (a)) − tr(TT (∇a))

(1.92)

Let b = div T. To determine the components bi of div T, we obtain: bi = b · ei = div TT (ei ) − tr TT (∇ei ) = div (Tim em ) − tr TT (0) = div (Tim em ) ∂Tim = ∂xm

(1.93)

Note in equation (1.92) that ∇ei = 0 (see equation (1.87). Therefore, div T is a vector defined by: ∂Tim ei (1.94) ∂xm Let v(r) be a vector field as defined above. The curl of v, denoted by curlv, is a vector field defined by: divT =

curlv = 2tA

(1.95)

where tA is the dual vector of the antisymmetric part of ∇v, i.e., ((∇v)A . See Problem 1.89 for the definition of the dual vector for an antisymmetric tensor. A Using equation (1.88), (∇v) is obtained as follows: ⎡ 0

⎢ ⎢ ∂v1 (∇v)A ≡ ⎢− 12 ∂x − 2 ⎣ 1 ∂v1 − 2 ∂x3 −

∂v2 ∂x1 ∂v3 ∂x1

1 2

− 12

∂v1 ∂x2

−

∂v2 ∂x1

0 ∂v2 ∂x3

−

∂v3 ∂x2

∂v1 ∂x3 1 ∂v2 2 ∂x3 1 2

− −

⎤

∂v3 ∂x1 ⎥ ∂v3 ⎥ ∂x2 ⎥ ⎦

(1.96)

0

The curl of v is then obtained as follows: curlv =

∂v3 ∂v2 − ∂x2 ∂x3

e1 +


∂v1 ∂v3 − ∂x3 ∂x1

e2 +

∂v2 ∂v1 − ∂x1 ∂x2

e3 (1.97)


69

Example 1.18 Prove equation (1.79a) Solution d lim (T + S) (t + ∆t) − (T + S) (t) (T + S) = ∆t →0 dt ∆t lim T (t + ∆t) + S (t + ∆t) − T(t) − S(t) = ∆t → 0 ∆t lim S(t + ∆t) − S(t) lim T(t + ∆t) − T(t) + = ∆t →0 ∆t → 0 ∆t ∆t dT dS + = dt dt

Example 1.19 Given the scalar field Φ = x2 + 2yz − 3z 2 , determine the vector n = −α∇Φ where α is a scalar. Solution ∂Φ ∂Φ ∂Φ e1 + e2 + e3 ∂x ∂y ∂z = 2xe1 + 2ze2 + (2y − 6z)e3 n = −2α[xe1 + ze2 + (y − 3z)e3 ]

∇Φ =

Example 1.20 Consider the vector field v = x2 e1 + y 2 e2 + z 2 e3 . Determine the matrix representation of the tensor ∇v at the point (1,1,1). Solution

⎡ ∂v ⎢ ∇v ≡ ⎣

1 ∂v1 ∂v1 ∂x ∂y ∂z ∂v2 ∂v2 ∂v2 ∂x ∂y ∂z ∂v3 ∂v3 ∂v3 ∂x ∂y ∂z

where v1 = e1 · v = x2 v2 = e2 · v = y 2 v3 = e3 · v = z 2


⎤ ⎥ ⎦

70

Damage Mechanics ⎡

⎤ 2x 0 0 ∇v = ⎣ 0 2y 0 ⎦ 0 0 2z At the point (1,1,1), ⎡

⎤ 200 ∇v = ⎣ 0 2 0 ⎦ = 2I 002

Example 1.21 Let Φ be a scalar field and v be a vector field. Prove the following relation: div(Φv) = ∇Φ · v + Φ(divv) Solution ldiv(Φv) = tr(∇ (Φv)) ∂ (Φv1 ) ∂ (Φv2 ) ∂ (Φv3 ) = + + ∂x1 ∂x2 ∂x3 ∂v1 ∂Φ ∂v2 ∂Φ ∂v3 ∂Φ =Φ + v1 + Φ + v2 + Φ + v3 ∂x ∂x1 ∂x2 ∂x ∂x3 ∂x3 1 2 ∂Φ ∂Φ ∂Φ ∂v2 ∂v3 ∂v1 = v1 + v2 + v3 + Φ +Φ +Φ ∂x1 ∂x2 ∂x3 ∂x1 ∂x2 ∂x3 = ∇Φ · v + Φ(div v)

Example 1.22 Consider the vector field v given in Example 1.20. Determine div v and curl v at the point (1,1,1). Solution divv =

∂v1 ∂v2 ∂v3 + + =2+2+2=6 ∂x ∂y ∂z

∂v3 ∂v1 ∂v2 ∂v2 ∂v3 ∂v1 − − − e1 + e2 + e3 ∂y ∂z ∂z ∂x ∂x ∂y = (0) e1 + (0) e2 + (0) e3

curl v =

=0



71

Problems 1.113 Prove equations (1.79b), (1.79c), (1.79d), and (1.79e). 1.114 Given the scalar field Ψ (x, y, z) = 2xyz, determine the gradient vector ∇Ψ. 1.115 Given the vector field v = xye1 + xze2 + yze3 , determine ∇ v, div v, and curl v. 1.116 For a general scalar field Φ, show that curl(∇Φ) = 0. 1.117 For a general vector field v, show that div(curl v) = 0. 1.118 Let Φ and Ψ be two general scalar fields. Show that ∇ (Φ + Ψ) = ∇Φ + ∇Ψ. 1.119 Let u and v be two general vector fields. Show that div(u + v) = div u + div v. 1.120 Prove equation (1.96). 1.121 For any general vector field v, show that curl(curlv) = ∇ (div v) ∇ (∇v). ∂vk 1.122 Show that (curlv)i = ijk ∂x where v is a general vector field. j

1.123 Define the Laplacian ∇2 v of a vector field v as ∇2 = ∇ (∇v). Show ∂2 v that ∇2 v j = ∂xi ∂xj i . 1.124 Let Φ and Ψ be two general scalar fields. Show that ∇ (ΦΨ) = (∇Φ) Ψ + Φ (∇Ψ). 2 2 2 1.125 Let v be a vector field given dv by v = x ye1 + xy e2 + z e3 . Determine the maximum value of dr at the point (1,2,3).

1.126 Let f = f (φ, ψ) be a scalar function where φ and ψ are scalar fields. Show that the following relation holds: ∇f =

∂f ∂f ∇φ + ∇ψ ∂φ ∂ψ 3

1.127 Let Φ be a scalar field given by Φ = eaz sin(bx) cosh(cy) where a, b, and c are scalars. Determine the vector v = −∇Φ. 1.128 Find a vector normal to the surface xy − z = 1 at the point (2, 1, 1).


72

Damage Mechanics

1.129 Let r be the position vector for a general point (x, y, z) in threedimensional space. Show that: (a) div r = 3 (b) curl r = 0 (c) div (r−3 r) = 0 where r is the length of the vector r. 1.130 Let r be the radius vector of a typical point in a field and r be the length of r. Show that: (a) div (rn r) = (n + 3) rn (b) curl (rn r) = 0 (c) ∇ (∇ (rn )) = n (n + 1) rn−2 1.131 Let Φ be a general scalar field and let T be a general tensor field. Show that the following relation holds: div (ΦT) = T (∇Φ) + ΦdivT

1.132 Let T be a symmetric tensor and S be an antisymmetric tensor. Show that tr(TS) = 0. 1.133 Let Q(t) be an orthogonal tensor. Show that metric tensor.

dQ T dt Q

is an antisym-

1.134 Use polar coordinates with er and eθ representing unit vectors in the coordinate directions of r and θ, respectively. We have the position vector r and dr given by: r = rer dr = drer + rdθeθ where r and dr are the lengths of r and dr, respectively, and the vectors er and eθ are given by the following two equations: er = cos θe1 + sin θe2 eθ = − sin θe1 + cos θe2 Prove the following relations using polar coordinates:



73

(a) ∇f =

∂f 1 ∂f er + eθ ∂r r ∂θ

where f is a scalar valued function, i.e., f ≡ f (r, θ). (b) ∇v is represented by the following matrix: ∇v ≡

∂vr

1 ∂r r ∂vθ 1 ∂r r

∂vr ∂θ − vθ ∂v θ ∂θ + vr

where v is a vector field, i.e. v = vr er + vθ eθ and both vr and vθ are scalar functions, i.e. vr (r, θ) and vθ (r, θ). 1 ∂vθ r (c) div v = ∂v ∂r + r ∂θ + vr vθ 1 ∂vr θ (d) curl v = ∂v ∂r + r − r ∂θ e3 (e) (divT)r =

1 ∂Trθ Trr − Tθθ ∂Trr + + ∂r r ∂θ r

(divT)θ =

1 ∂Tθθ Trθ + Tθr ∂Tθr + + ∂r r ∂θ r

where T is a tensor field, represented by the matrix: T≡

1.9

Trr Trθ Tθr Tθθ

Maple Tensor Commands

In this section we present the commands for many tensor operations appearing in sections 1.6, 1.7, and 1.8. Concerning section 1.7 on eigenvalues and eigenvectors of second-order tensor, we can determine the eigenvalues and the eigenvectors of their corresponding matrix representation. This can be performed using the Maple commands eigenvals and eigenvects. See section 1.3 for more details on these two commands. Next, we present the three Maple commands grad, diverge and curl for the vector and tensor operations in section 1.8. The Maple command grad is used to determine the gradient vector of a scalar function. This is illustrated by the following example:


74

Damage Mechanics >

grad(x^2+y^2+z^2,[x,y,z]); [2 x, 2 y, 2 z]

>

sf:=f(x,y,z); sf := f(x, y, z)

>

grad(sf,[x,y,z]); ∂ ∂x f(x, y, z),

∂ ∂y

f(x, y, z),

∂ ∂z

f(x, y, z)

In performing the above commands, you must invoke the linear algebra package first using the command with(linalg);. The Maple command diverge determines the divergence of vector functions. The following examples illustrate the use of this command: >

diverge([x*cos(y),y*cos(x),z],[x,y,z]); cos(y) + cos(x) + 1

>

vf:=[fx(x,y,z),fy(x,y,z),fz(x,y,z)]; vf := [fx(x, y, z), fy(x, y, z), fz(x, y, z)]

>

diverge(vf,[x,y,z]); ∂ ∂ ∂ fx(x, y, z)) + ( ∂y fy(x, y, z)) + ( ∂z fz(x, y, z)) ( ∂x

The Maple command curl is used to calculate the curl of a vector function. The following examples illustrate the use of this command: >

curl([x*cos(y),y*cos(x),z],[x,y,z]); [0, 0, −y sin(x) + x sin(y)]

>

vf:=[fx(x,y,z),fy(x,y,z),fz(x,y,z)]; vf := [fx(x, y, z), fy(x, y, z), fz(x, y, z)]

>

curl(vf,[x,y,z]);

∂ ∂ ∂ ∂ ( ∂y fz(x, y, z)) − ( ∂z fy(x, y, z)), ( ∂z fx(x, y, z)) − ( ∂x fz(x, y, z)), ∂ ∂ fy(x, y, z)) − ( ∂y fx(x, y, z)) ( ∂x Finally, it should be noted that all three commands grad, diverge, and curl can be used for non-Cartesian coordinates, like cylindrical coordinates. This will be explored further in Problems 1.144 and 1.145.



75

Problems 1.135 Let Φbe a scalar function given by Φ(x, y, z) = x cos y + y cos z + z cos x. Determine the gradient vector ∇Φ using Maple. 1.136 Solve Example 1.19 again using Maple. 1.137 Solve Problem 1.114 again using Maple. 1.138 Let a vector field given by u = x2 − y 2 e1 + z 2 − x2 e2 + 2 u be y − z 2 e3 . Determine the three quantities ∇u, div u and curlu using Maple. 1.139 Solve Example 1.20 again using Maple. 1.140 Solve Example 1.22 again using Maple. 1.141 Solve Problem 1.115 again using Maple. 1.142 Solve Problem 1.127 again using Maple. 1.143 Solve Problem 1.128 again using Maple. 1.144 Let v be a vector field given as follows in cylindrical coordinates, v = r cos θe1 + r sin θe2 + re3 , where r and θ are scalars. Determine ∇v, div v and curlv using Maple. 1.145 Solve Problem 1.134 again using Maple.


2 Elasticity Theory

In this chapter we present a summary of the theory of elasticity including the concepts of force, deformation, stress, and strain. This is achieved using both the material description and the spatial description. The theory of elasticity is reviewed in this chapter based on the book of Lai et al.(1984).

2.1

Motion of a Continuum

Consider a body occupying a certain region of space at time t = to . Let X denote the position vector of a particle in the body measured from an origin point O (see Figure 2.1). Then, the motion of every particle is described by the equation x = x(X, t) X = x(X, to )

(2.1)

where X denotes the position of the particle at t = to . During the motion of a continuum, we describe it using either one of two approaches as follows: 1. By following the particles, i.e., we express the variables as functions of the particle material coordinates X and time t. This approach is known as the material description or the Lagrangian description. 2. By observing the changes at fixed locations, i.e., we express the variables as functions of fixed position x and time t. This approach is known as the spatial description or the Eulerian description. Consequently, the coordinates X are called the material coordinates while the coordinates x are known as the spatial coordinates. Equation 2.1 relates these two types of coordinates and can be written explicitly as follows:


77

78

Damage Mechanics

P(to)

X

P(t)

x

O FIGURE 2.1 A particle in a body at times t0 and t with position vectors X and x, respectively.(Lai et al., 1984)

x1 = x1 (X1 , X2 , X3 , t) x2 = x2 (X1 , X2 , X3 , t) x3 = x3 (X1 , X2 , X3 , t)

(2.2)

The material description is defined as the time rate of change of a quantity of a material particle. Let D/Dt denote the material derivative. We next explore the material derivative using both the material description and the spatial description of motion. 1. Using the material description of a quantity like φ(X, t), then the material derivative Dφ/Dt is given by: Dφ ∂φ = Dt ∂t x is fixed

(2.3)

2. Using the spatial description of a quantity like φ(x, t), then the material derivative Dφ/Dt is given by: ∂φ ∂φ ∂x2 ∂φ ∂x3 ∂φ ∂φ ∂x1 Dφ = + + + = Dt ∂t X is fixed ∂x1 ∂t ∂x2 ∂t ∂x3 ∂t ∂t x is fixed (2.4)


Elasticity Theory

79

Note in the above equation that ∂xi /∂t = vi where vi is the component of the velocity of the particle along xi . Therefore, equation (2.4) can be written in compact form as follows: ∂φ Dφ = + v · ∇φ Dt ∂t

(2.5)

where ∇φ is the gradient vector of the quantity φ. Note that equation (2.5) is valid for all coordinate systems, while equation (2.4) is valid only for rectangular Cartesian coordinates. The acceleration of a particle is the material derivative of the velocity of the particle. The velocity v and acceleration a, at time t, of a particle X, are defined as follows: v=

Dx Dt

(2.6a)

a=

Dv Dt

(2.6b)

Next, we explore the acceleration of a particle using both the material description and the spatial description of motion. 1. Using the material description of velocity v(X, t), it is straight forward to compute the acceleration a(X,t) as follows: a=

Dv ∂v = Dt ∂t X is fixed

(2.7)

2. Using the spatial description of velocity v(x, t), we need to compute the acceleration a(x, t) as follows: a=

Dv Dv1 Dv2 Dv3 = e1 + e2 + e3 Dt Dt Dt Dt Dvi ∂vi ∂vi = + vj Dt ∂t ∂xj

(2.8a)

(2.8b)

Therefore, we obtain: ai = or equivalently we have:


∂vi ∂vi + vj ∂t ∂xj

(2.9)

80

Damage Mechanics

a=

∂v + (∇v)v ∂t

(2.10)

Example 2.1 Given the motion of a body as follows:

x1 = X1 x2 = X2 + αtX1 x3 = X3 where α is constant. Let the temperature field be given by the spatial description as T = βx1 + γx2 where β and γ are constants. a. Determine the material description of temperature T(X1 , X2 , X3 , t). b. Determine the velocity and rate of change of temperature using both the material description and the spatial description. Solution a. T (X1 , X2 , X3 , t) = βx1 + γx2 = βX1 + γ(X2 + αtX1 ) T = (β + αγt)X1 + γX2

b. vi = Therefore, v1 = v2 = v3 =

∂xi ∂t X is fixed ∂x1 =0 ∂t ∂x2 = αX1 ∂t ∂x3 =0 ∂t

The above equations represent the material description of velocity. The following is the spatial description:


Elasticity Theory

81

v1 = 0 v2 = αx1 v3 = 0 The rate of change of temperature ∂θ/∂t is given as follows in both descriptions: ∂θ = αγX1 ∂t ∂θ = αγx1 ∂t

using the material description using the spatial description

Example 2.2 Given the following motion x1 = X1 x2 = X2 x3 = X3 + αt etermine the velocity and acceleration of a particle using both the material description and spatial description where α is a constant.

Solution In the material description, we have: v1 = 0 v2 = 0 v3 = α a1 = 0 a2 = 0 a3 = 0 sing the spatial description, we have: v1 = 0 v2 = 0 v3 = α a1 = 0 a2 = 0 a3 = 0


82

Damage Mechanics

Problems 2.1. Given the following motion using the material description: x1 = X1 + βX1 x2 = X2 + αX2 x3 = X3 where α and β are constants. Write the motion using the spatial description. 2.2. Describe the motion given in problem 2.1 geometrically. 2.3. Consider the motion given in problem 2.1. (a) Determine the velocity field using the material description. (b) Determine the velocity field using the spatial description. (c) Determine the acceleration field using the material description. (d) Determine the acceleration field using the spatial description. 2.4. Consider the motion given in Problem 2.1. Let φ be a scalar field given by φ = x1 − x2 + 2x3 . (a) Determine the material description of φ. (b) Determine the rate of change of φ using the material description. (c) Determine the rate of change of φ using the spatial description. 2.5. Consider a velocity field given by: v1 =

x1 1−t

v2 =

x2 1−t

v3 =

x3 1−t

Determine the acceleration field. 2.6. Consider the velocity field of problem 2.5. Determine the motion x = x(X, t).


Elasticity Theory

83

2.7. Consider the following motion: x1 = X1 − α1 t x2 = X2 − α2 t x3 = X3 − α3 t where α1 , α2 and α3 are constants. (a) Determine the motion using the spatial description. (b) Determine the velocity field using both the material description and the spatial description. (c) Determine the acceleration field using both the material description and the spatial description. 2.8. Consider the motion of Problem 2.7. Let φ be a scalar field given by φ = x1 x2 x3 . (a) Determine the material description of φ. (b) Determine Dφ Dt using both the material description and the spatial description.

2.2

Deformation and Strain

Let a body deform from an initial configuration at to to a final configuration at t (see Figure 2.2). Let P and Q be two points separated by an infinitesimal distance dX initially and dx finally. Point P undergoes a displacement u such that: x = X + u(X, t)

(2.11)

The neighboring point Q has a displacement u(X + dX, t) according to the equation: dx = dX + u(X + dX, t) − u(X, t)

(2.12)

The above equation is clear from the geometry shown in Figure 2.2. Equation (2.12) can be rewritten as follows: dx = dX + (∇u)dX


(2.13)

84

Damage Mechanics

Q(to)

u(X + dX) Q(t)

dX u(X)

dx

P(to)

P(t)

X x

O FIGURE 2.2 Deformation of a body between t0 and t.(Lai et al., 1984) where ∇u is a second-order tensor called the displacement gradient. The tensor ∇u has the following matrix representation: ⎡ ⎤ ∂u1

1 ⎢ ∂X ∂u2 ∇u ≡ ⎣ ∂X 1

∂u3 ∂X1

∂u1 ∂X2 ∂u2 ∂X2 ∂u3 ∂X2

∂u1 ∂X3 ∂u2 ∂X3 ∂u3 ∂X3

⎥ ⎦

(2.14)

It is clear from equation (2.13) that if dx = dX, then ∇u = 0. This special case corresponds to a rigid body motion. Consider now two material vectors dX1 and dX2 at point P. After deformation, they become dx1 and dx2 , respectively, such that (from equation (2.13)): dx1 = dX1 + (∇u)(dX1 ) 2

2

2

dx = dX + (∇u)(dX )

(2.15a) (2.15b)

Consider now the dot product dx · dx : 1

2

dx1 · dx2 = dX1 · dX2 + dX1 · (∇u)(dX2 ) + dX2 · (∇u)(dX1 ) + [(∇u)(dX1 )] · [(∇u)(dX2 )] (2.16) Simplifying equation (2.16) we obtain:


Elasticity Theory

85

dx1 · dx2 = dX1 · dX2 + dX1 · [(∇u) + (∇u)T + (∇u)T (∇u)](dX2 ) (2.17) Define the second-order tensor E∗ as follows: 1 (2.18) [(∇u) + (∇u)T + (∇u)T (∇u)] 2 Next we substitute equation (2.18) into equation (2.17) to obtain: E=

dx1 · dx2 = dX1 · dX2 + 2dX1 · E∗ (dX2 )

(2.19)

It is clear from equation (2.19) that if E∗ = 0, then dx1 ·dx2 = dX1 ·dX2 , i.e., E∗ characterizes the deformation of the neighborhood of the particle P. The tensor E∗ is called the Lagrangian Strain Tensor. Using equation (2.18), we can write the components of E∗ with respect to rectangular Cartesian coordinates as follows: E∗ij =

1 ∂ui ∂uj ∂uk ∂uk ( + + ) 2 ∂Xj ∂Xi ∂Xi ∂Xj

(2.20)

Equations (2.18) and (2.20) apply to general cases of deformation involving large strains. For the special case of small strains and small deformations, the term (∇u)T (∇u) can be neglected. Therefore, equation (2.18) becomes: 1 E∗ ∼ = [(∇u) + (∇u)T ] = (∇u)S 2

(2.21)

where (∇u)S is the symmetric part of ∇u. Let E denote the strain tensor for small deformation, also called the infinitesimal strain tensor. Then equations (2.19) and (2.21) become: dx1 · dx2 = dX1 · dX2 + 2dX1 · E(dX2 )

(2.22)

1 [(∇u) + (∇u)T ] (2.23) 2 It should be noted that the anti-symmetric part of ∇u is called the infinitesimal rotation tensor or just the rotation tensor, denoted Ω and given by : E=

1 (∇u) − (∇u)T (2.24) 2 The angle and axis of the rotation is determined by the dual vector of Ω. Ω=


86

Damage Mechanics

Next, we write the components of E explicitly as follows (see equation (2.20)): 1 ∂ui ∂uj + Eij = (2.25) 2 ∂Xj ∂Xi The matrix representation of E is given as follows: ⎡

∂u1 ∂X1

⎢ ⎢ ∂u1 E ≡ ⎢ 12 ∂X + ⎣ 2 ∂u1 1 2 ∂X3 +

∂u2 ∂X1 ∂u3 ∂X1

∂u1 ∂X2 + ∂u2 ∂X2 ∂u2 1 2 ∂X3 + 1 2

∂u2 ∂X1

∂u3 ∂X2

∂u1 + ∂X3 ∂u2 1 2 ∂X3 + ∂u3 ∂X3 1 2

⎤

∂u3 ∂X1 ⎥ ∂u3 ⎥ ∂X2 ⎥ ⎦

(2.26)

Next, we will discuss the rate of deformation. Consider a material segment dx at a material point P located at x at time t. Using x = x(X, t) we can obtain: dx = x(X + dX, t) − x(X, t) Therefore, the material derivative

D Dt (dx)

(2.27)

is obtained as follows:

D (dx) = v(X + dX, t) − v(X, t) = (∇X v)(dX) (2.28) Dt where (∇X v) is the gradient of v with respect to the material coordinate D X. Equation (2.28) represents the material derivative Dt (dx) using the D material description. We write now Dt (dx) using the spatial description as follows: D (dx) = v(x + dx, t) − v(x, t) = (∇x v)(dx) (2.29) Dt where (∇x v) is the spatial gradient of velocity. We will use ∇v instead of ∇x v to denote this spatial gradient in the following derivations. The matrix representation of ∇v is given as follows: ⎤ ⎡ ∂v1 ∂v1 ∂x2 ∂v2 ∂x2 ∂v3 ∂v3 ∂x1 ∂x2

1 ⎢ ∂x ∂v2 ∇v ≡ ⎣ ∂x 1

∂v1 ∂x3 ∂v2 ∂x3 ∂v3 ∂x3

⎥ ⎦

(2.30)

In general, ∇v can be decomposed into its symmetric and anti-symmetric parts as follows: ∇v = D + W where D is called the rate of deformation tensor given by:


(2.31)

Elasticity Theory

87

(∇v) + (∇v)T 2 and W is called the spin tensor given by: D=

(2.32)

(∇v) − (∇v)T (2.33) 2 The matrix representations of both D and W are given explicitly as follows based on equations (2.32) and (2.33): ⎡ ⎤ ∂v1 ∂v2 ∂v3 1 ∂v1 1 ∂v1 + + ∂x1 2 ∂x3 ∂x1 ⎥ ⎢ ∂x1 2 ∂x2 ⎢ 1 ∂v1 ∂v2 ∂v2 ∂v3 ⎥ 1 ∂v2 (2.34) D ≡ ⎢ 2 ∂x2 + ∂x1 + ∂x ⎥ 2 ⎣ ⎦ ∂x2 2 ∂x3 ∂v3 ∂v3 ∂v3 1 ∂v1 1 ∂v2 2 ∂x3 + ∂x1 2 ∂x3 + ∂x2 ∂x3 W=

⎡ 0

⎢ ⎢ ∂v1 W ≡ ⎢ − 12 ∂x − ⎣ 2 ∂v1 − 12 ∂x − 3

∂v2 ∂x1 ∂v3 ∂x1

1 2

− 12

−

∂v1 ∂x2

∂v2 ∂x1

0 ∂v2 ∂x3

−

∂v3 ∂x2

∂v1 ∂x3 1 ∂v2 2 ∂x3 1 2

− −

⎤

∂v3 ∂x1 ⎥ ∂v3 ⎥ ∂x2 ⎥ ⎦

(2.35)

0

Example 2.3 Given the following displacement field: u1 = 0.001X22 u2 = 0 u3 = 0 Determine the infinitesimal strain tensor E.

Solution First, determine the matrix representation of ∇u as follows: ⎡ ⎤ 0 0.002X2 0 ∇u ≡ ⎣ 0 0 0⎦ 0 0 0 The infinitesimal strain tensor is then obtained as the symmetric part of ∇u: ⎤ ⎡ 0 0.001X2 0 0 0⎦ E = (∇u)S ≡ ⎣ 0.001X2 0 0 0


88

Damage Mechanics

Example 2.4 Given the following velocity field: v1 = αx2 v2 = 0 v3 = 0 Determine the rate of deformation tensor D and the spin tensor W. Solution First, we determine the matrix representation of ∇v as follows: ⎡

⎤ 0α0 ∇v ≡ ⎣ 0 0 0 ⎦ 000 Then, the tensors D and W are determined as the symmetric and antisymmetric parts of ∇v, respectively, as follows: ⎡

⎤ 0 D = (∇v)S = ⎣ α2 0 0 ⎦ 0 0 0 0

α 2

⎡

⎤ 0 α2 0 W = (∇v)A = ⎣ − α2 0 0 ⎦ 0 0 0

Problems 2.9. Given the following displacement field: u1 = k1 X22 u2 = k2 X21 u3 = 0 where k1 and k2 are constants. Determine the infinitesimal strain tensor E. 2.10. Consider the displacement field given in Problem 2.9. Using the strain tensor E, determine the unit elongation for the material elements dX1 = dX1 e1 and dX2 = dX2 e2 which were at the point (1,1,0) of a unit square. Also, determine the decrease in angle between these two elements.


Elasticity Theory

89

2.11. Given the following displacement field: u1 = α(X21 + βX22 ) u2 = α(X21 − βX22 ) u3 = 0 where α = 1 × 10−4 and β = 2. (a) Determine the unit elongations and the change of angle for two material elements dX1 = dX1 e1 and dX2 = dX2 e2 that emanate from a particle designated by X = e1 + e2 . (b) Determine the deformed position of these two elements dX1 and dX2 . 2.12. Consider the following displacement field: u1 = 0 u2 = αX2 u3 = 0 where α = 1 × 10−3 . Let this displacement field act on a unit cube, with its edges parallel to the coordinate axes. Determine the increase in length of the diagonal AB (see Figure 2.3). 2.13. Given the following velocity field: v1 = α1 (x1 + x2 ) v2 = α2 (x1 − x2 ) v3 = 0 where α1 and α2 are scalars. Determine the rate of deformation tensor and spin tensor. 2.14. Consider the velocity field given in Problem 2.13. (a) Determine the rate of extension of the material elements: dx1 = (ds1 )e1 dx2 = (ds2 )e2 dx = dl(2e1 + e2 ) (b) Determine the maximum and minimum rates of extension.


90

Damage Mechanics

X2

B' B

1 unit

A

1 unit

X1

FIGURE 2.3 Unit cube subjected to a displacement field.

2.15. Given the following strain tensor with reference to an x1 - x2 - x3 coordinate system: ⎡

⎤ 1 2 0 E ≡ ⎣ 2 5 −1 ⎦ × 10−4 0 −1 3 (a) Determine the unit elongation in the direction e1 + e2 + e3 . (b) What is the change of angle between two perpendicular lines (in the undeformed state) emanating from the point and in the direction of 2e1 + 2e2 + 2e3 and 3e1 − 6e3 . 2.16. Consider the state of strain given in Problem 2.16. Determine the scalar invariants of the state of strain.


Elasticity Theory

91

2.17. Show that the following matrix ⎡

⎤ 300 ⎣ 0 2 0 ⎦ × 10−4 005 cannot represent the same state of strain given in Problem 2.16. 2.18. Consider a material element dx = (ds)n. (a) Show that (D/Dt)n = Dn + Wn − (n · D(n))n. (b) Show that if n is an eigenvector of D that (D/Dt)n = Wn = ω × n where ω is the dual vector of W. 2.19. Prove the six equations of compatibility of strain components given below: ∂ 2 E22 ∂ 2 E12 ∂ 2 E11 + =2 2 2 ∂X2 ∂X1 ∂X1 ∂X2

(2.36a)

∂ 2 E33 ∂ 2 E23 ∂ 2 E22 + = 2 ∂X23 ∂X22 ∂X2 ∂X3

(2.36b)

∂ 2 E33 ∂ 2 E11 ∂ 2 E31 + =2 2 2 ∂X1 ∂X3 ∂X3 ∂X1

(2.36c)

∂ ∂ 2 E11 = ∂X2 ∂X3 ∂X1

∂E33 ∂E31 ∂E12 − + + ∂X1 ∂X2 ∂X3

(2.36d)

∂ ∂ 2 E22 = ∂X3 ∂X1 ∂X2

∂E23 ∂E31 ∂E12 + + − ∂X2 ∂X3 ∂X1

(2.36e)

∂ 2 E33 ∂ = ∂X1 ∂X2 ∂X1

∂E23 ∂E31 ∂E12 + + − ∂X3 ∂X1 ∂X2

(2.36f)

2.20. Check whether or not the following state of strain satisfies the compatibility conditions given in Problem 2.19. ⎡

⎤ X21 X1 + X2 X1 + X3 X22 X2 + X3 ⎦ E ≡ ⎣ X1 + X2 X1 + X3 X2 + X3 X23


92

Damage Mechanics

2.21. Consider the following displacement field: u1 = sin X1 u2 = cos X2 u3 = tan X3 Does the above displacement field correspond to a strain field that satisfies the compatibility conditions given in Problem 2.19. 2.22. Give an example of a displacement field with a corresponding strain field that satisfies the compatibility equations given in Problem 2.19. 2.23. Consider the following strain field: ⎡ E≡⎣

1 α f(X2 , X3 )

0 0

⎤ 0 0 ⎦ − αν f(X2 , X3 ) 0 ν 0 − α f(X2 , X3 )

where ν and α are constants. What restrictions must f(X2 , X3 ) satisfy so that the above strain field E satisfies the compatibility equations given in Problem 2.19. 2.24. Write general expressions for the scalar invariants I1 , I2 , and I3 of the strain tensor E. 2.25. Define the principal strain and write a general expression for the principal strain matrix. 2.26. We define dilatation, denoted by e, as the unit volume change. Show that: e = Eii = E11 + E22 + E33 = divu where we have assumed small deformation. 2.27. Derive the equations of compatibility for the rate of deformation components Dij in a similar way to those given in Problem 2.19. 2.28. Consider the rate of deformation tensor D obtained after solving Problem 2.13. Does this tensor satisfy the compatibility conditions derived in Problem 2.27. 2.29. Give an example of a velocity field with a corresponding rate of deformation tensor that satisfies the compatibility equations derived in Problem 2.27.


Elasticity Theory

93

2.30. Show that the acceleration components in cylindrical coordinates ar , aθ , and az , are given as follows: ar =

aθ =

vθ ∂vr v2 ∂vr ∂vr ∂vr + vr + + vz − θ ∂t ∂r r ∂θ ∂z r

vθ ∂vθ vr vθ ∂vθ ∂vθ ∂vθ + vr + + vz + ∂t ∂r r ∂θ ∂z r

az =

vθ ∂vz ∂vz ∂vz ∂vz + vr + + vz ∂t ∂r r ∂θ ∂z

2.31. Let ur , uθ , and uz be the displacement components in cylindrical coordinates. Show that the components of the strain tensor E in cylindrical coordinates are given by: ∂ur ∂r ur 1 ∂uθ + Eθθ = r ∂θ r ∂uz Ezz = ∂z ∂uθ ∂uθ 1 1 ∂ur − + = 2 r ∂θ r ∂r Err =

Erθ

Eθr = Erθ ∂uz 1 ∂ur + Erz = 2 ∂z ∂r

Eθz

Ezr = Erz 1 ∂uθ 1 ∂uz = + 2 ∂z r ∂θ Ezθ = Eθz

2.32. Let vr , vθ , and vz be the velocity components in cylindrical coordinates. Show that the components of both the rate of deformation tensor D and the spin tensor W, in cylindrical coordinates, are given by: Drr =


∂vr ∂r

94

Damage Mechanics vr 1 ∂vθ + r ∂θ r ∂vz Dzz = ∂z ∂vθ ∂vθ 1 1 ∂vr − + = 2 r ∂θ r ∂r Dθθ =

Drθ

Dθr = Drθ ∂vz 1 ∂vr + Drz = 2 ∂z ∂r

Dθz =

1 2

Dzr = Drz 1 ∂vz ∂vθ + , symmetric. ∂z r ∂θ

Dzθ = Dθz Wrr = 0 Wθθ = 0

Wrθ =

1 2

Wzz = 0 ∂vθ ∂vθ 1 ∂vr − + r ∂θ r ∂r

Wθr = −Wrθ ∂vz 1 ∂vr − Wrz = 2 ∂z ∂r

Wθz

Wzr = −Wrz 1 ∂vz 1 ∂vθ − = 2 ∂z r ∂θ Wzθ = −Wθz

2.3

Stress

In this section we will describe the forces inside a body in terms of the stress vector and the stress tensor. In addition, the equations of the equilibrium will be formulated in terms of the stress tensor. Finally, principal stresses and principal directions will be discussed. Consider a body subjected to external forces as shown in Figure 2.4. Let n be the unit normal at an arbitrary point P where a plane S passes


Elasticity Theory

95 Plane S

∆A F1

F4

∆F

F4

n P P

F3

F2

F3

FIGURE 2.4 A sectional plane S is taken at an arbitrary point P in the body.(Lai et al., 1984)

as shown in the figure. Let ∆F be the resultant force acting on a small area ∆A around point P. The stress vector tn at point P on the plane S is defined as follows: tn =

lim

∆A−→0

∆F ∆A

(2.37)

where tn points outward away from the surface S. Replacing the plane S and replacing the small area ∆A by a small surface area ∆S (on the surface), the stress vector at point P on the surface is then defined as follows: ∆F ∆S−→0 ∆S

tn = lim

(2.38)

It should be noted that t ≡ t (x, t, n) which means that the stress vector at any given place x and time t has a common value on all parts of material having a common tangent plane at P and lying on the same side of it. This is known as the Cauchy stress principle. Let n be the normal vector to a plane and let T be a transformation such that the stress vector on the plane is given by tn = T(n)

(2.39)

We will show next that T is a linear transformation, i.e., a second-order tensor. Consider a small tetrahedron isolated from the body with the point P as one of its vertices, as shown in Figure 2.5. It should be noted that the size (or volume) of the tetrahedron approaches zero so that the inclined plane passes through point P.


96

Damage Mechanics x2

B t-e3

t-e1

tn = T(n) ∆x2 P ∆x3

∆x1 A

x1

C x3 t-e2 = T(-e2) = -T(e2)

FIGURE 2.5 Stress tetrahedron.(Lai et al., 1984)

The stress vector t−e1 on the face PAB, whose outward normal is in the direction of −e1 , is given by (based on equation (2.39)): t−e1 = −te1 = −T(e1 )

(2.40a)

Similarly, the stress vectors t−e2 and t−e3 on the faces PBC and PAC, respectively, are given by: t−e2 = −T(e2 )

(2.40b)

t−e3 = −T(e3 )

(2.40c)

Let ∆A1 , ∆A2 , and ∆A3 be the areas of faces PAB, PBC, and PAC, respectively. Using Newton‘s second law, we can write the following:

F = t−e1 (∆A1 ) + t−e2 (∆A2 ) + t−e3 (∆A3 ) + tn (∆An ) = ma (2.41)


Elasticity Theory

97

where ∆An is the area of the inclined face ABC. When the volume of the tetrahedron approaches zero, the right-hand-side of the equation (2.41) vanishes, i.e. ma = 0. Therefore, we obtain: t−e1 (∆A1 ) + t−e2 (∆A2 ) + t−e3 (∆A3 ) + tn (∆An ) = 0

(2.42)

Let the unit vector n on the inclined plane ABC given by: n = n1 e1 + n2 e2 + n3 e3

(2.43)

We now can write the areas ∆A1 , ∆A2 , and ∆A3 in terms of the inclined area ∆An , as follows: ∆A1 = n1 (∆An )

(2.44a)

∆A2 = n2 (∆An )

(2.44b)

∆A3 = n3 (∆An )

(2.44c)

Substituting equations (2.40) and (2.44) into equation (2.42) and simplifying, we obtain: T(n) = n1 T(e1 ) + n2 T(e2 ) + n3 T(e3 )

(2.45)

Combining equations (2.43) and (2.45) we can deduce that T is a linear transformation. T is now called the stress tensor. Using the equation te1 = T(e1 ) = T11 e1 + T21 e2 + T31 e3

(2.46)

we see that T11 is the normal component of the stress vector te1 , called the normal stress, while T21 and T31 are the shearing components of te1 , called the shear stresses. Similarly, we can interpret the components of te2 and te3 . Therefore, the diagonal elements T11 , T22 , and T33 are called the normal stresses, while the off-diagonal elements T21 , T31 , T12 , T32 , T23 , and T13 are called the shear stresses. Using equation (2.39), we can deduce the stress tensor components Tij as follows: ti = Tij nj

(2.47)

In matrix form, we can write equation (2.47) as follows: [t] = [T][n]


(2.48)

98

Damage Mechanics

Therefore, the state of stress at point P is completely characterized by the stress tensor T. In addition, the stress tensor T can be represented by a matrix as follows: ⎡ ⎤ T11 T12 T13 T ≡ ⎣ T21 T22 T23 ⎦ (2.49) T31 T32 T33 The stress tensor can be shown to be symmetric using the principle of moment of momentum (see Problem 2.37). Therefore, in this text we will always use T12 = T21 , T13 = T31 , and T23 = T32 . We know from Chapter 1 that for any symmetric tensor, there exists at least three mutually perpendicular principal directions corresponding to the eigenvalues of the tensor. In case of the stress tensor, the planes having these directions as their normals are called the principal planes. The normal stresses on these planes are called the principal stresses. Thus, the eigenvalues of T are the principal stresses which include the maximum and minimum values of normal stress among all planes passing through a given point. Next, we derive the differential equations of motion. Consider a small rectangular element that is isolated from the continuum in the neighborhood of the position xi , as shown in Figure 2.6. The vectors shown in the figure are the stress vectors on each face of the cube. Let B = Bi ei be the body force per unit mass, ρ be the mass density at xi , and a the acceleration of a particle at xi . Using Newton’s law of motion, we obtain: [

te1 (x1 + ∆x1 , x2 , x3 ) − te1 (x1 , x2 , x3 ) ∆x1

+ +

te2 (x1 , x2 + ∆x2 , x3 ) − te2 (x1 , x2 , x3 ) ∆x2

te3 (x1 , x2 , x3 + ∆x3 ) − te3 (x1 , x2 , x3 ) ]∆x1 ∆x2 ∆x3 ∆x3 +ρB∆x1 ∆x2 ∆x3 = ρa∆x1 ∆x2 ∆x3

(2.50)

Dividing equation (2.50) by ∆x1 ∆x2 ∆x3 and letting ∆xi −→ 0, we obtain: ∂te1 ∂te2 ∂te3 + + + ρB = ρa ∂x1 ∂x2 ∂x3

(2.51)

Substituting tej = T(ej ) = Tij ei , we have: ∂Tij ei + ρBi ei = ρai ei ∂xj


(2.52)

Elasticity Theory

99

x2 te2 t-e3

∆x2

t-e1 ∆x3

∆x1

te1 x1

x3 te3

t-e2

FIGURE 2.6 Infinitesimal cube with stress vectors Equation (2.52) can be written as follows after dropping the indicial notation: divT + ρB = ρa

(2.53)

Eliminating ei from equation (2.52), we can rewrite it in component form as follows: ∂Tij + ρBi = ρai (2.54) ∂xj Equation (2.54) is called Cauchy’s equation of motion. It must be satisfied for any continuum. If the acceleration vanishes, i.e., a = 0, then we obtain the equilibrium equation as follows: ∂Tij + ρBi = 0 ∂xj or equivalently,


(2.55)

100

Damage Mechanics

divT + ρB = 0

(2.56)

Example 2.5 Given the state of stress at a certain point in a body is represented by the following stress tensor: ⎡

⎤ 1 2 0 T ≡ ⎣ 2 3 −1 ⎦ MPa 0 −1 4 Determine the stress vector and the magnitude of the normal stress on a plane that passes through the point and is parallel to the plane x + y − z + 4 = 0.

Solution The plane x + y − z + 4 = 0 has a unit normal n given by: 1 n = √ (e1 + e2 − e3 ) 3 Therefore, we obtain the stress vector using equation (2.48) as follows: ⎡

⎡ ⎤⎡ ⎤ ⎤ 1 2 0 3 1 1 1 [t] = [T][n] = √ ⎣ 2 3 −1 ⎦ ⎣ 1 ⎦ = √ ⎣ 6 ⎦ 3 0 −1 4 3 −5 −1 1 t = √ (3e1 + 6e2 − 5e3 ) 3 The normal stress is now obtained as follows: Tn = t.n =

1 14 (3 + 6 + 5) = = 4.67 MPa. 3 3

Example 2.6 A case of plane stress is defined as a state of stress such that T13 = T23 = T33 = 0. For this case of plane stress, determine the principal stresses and the corresponding principal directions.


Elasticity Theory

101

Solution In this case, the stress tensor is written as follows: ⎡ ⎤ T11 T12 0 T ≡ ⎣ T12 T22 0 ⎦ 0 0 0 where we have used T21 = T12 because T is symmetric. The three stress invariants I1 , I2 , and I3 are obtained as follows: I1 = T11 + T22 T T 2 I2 = 11 12 = T11 T22 − T12 T12 T22 I3 = |T| = 0 Therefore, the characteristic equation of T is as follows: λ3 − I1 λ2 + I2 λ − I3 = 0 2 )λ = 0 λ3 − (T11 + T22 )λ2 + (T11 T22 − T12 2 )] = 0 λ[λ2 − (T11 + T22 )λ + (T11 T22 − T12

The three eigenvalues are now given as the solutions λ for the above equation: λ1 = 0 2 ) T11 + T22 + (T11 + T22 )2 − 4(T11 T22 − T12 λ2 = 2 2 ) T11 + T22 − (T11 + T22 )2 − 4(T11 T22 − T12 λ3 = 2 In order to find the corresponding eigenvectors, we set (Tij − λδij )nj = 0 and obtain nj for each one of the three eigenvalues. The three eigenvectors are then obtained as follows: n1 = e3 n2,3 = cos θe1 + sin θe2 where tan θ = −


T11 − λ T12

102

Damage Mechanics

Example 2.7 Consider the following stress distribution: T11 = x21 + x22 T12 = −x1 x2 T22 = x21 − x22 T13 = 0 T23 = 0 T33 = x21 x22 Does the above stress distribution satisfy the equations of equilibrium. Assume there are no body forces.

Solution Using equation (2.55) with i = 1, we obtain: ∂T1j + ρB1 = 0 ∂xj but B1 = 0: ∂T11 ∂T12 ∂T13 + + =0 ∂x1 ∂x2 ∂x3 2x1 + (−x1 ) + 0 = x1 = 0 Therefore, the stress distribution given does not satisfy the equations of equilibrium.

Problems 2.33. Consider the following state of stress given by the stress tensor: ⎤ 121 T ≡ ⎣ 2 3 5 ⎦ MPa 152 ⎡

Determine on which plane of the three coordinate planes (with normals e1 , e2 , e3 ) the normal stress is greatest.


Elasticity Theory

103

2.34. Consider the following state of stress given by the stress tensor: ⎡

⎤ 3 4 −1 T ≡ ⎣ 4 5 2 ⎦ MPa −1 2 5 (a) Determine the stress vector at the point on the plane whose normal is in the direction of the vector e1 + e2 + e3 . (b) Determine the magnitude of the normal and shear stress on this plane. 2.35. Solve problem 2.34 again for a plane which is parallel to the plane x1 − 2x2 + 3x3 = 4. 2.36. For any stress tensor T, define the deviatoric stress tensor TD by the equation: 1 TD = T − Tkk I 3 (a) Show that (TD )mm = 0 (b) Determine the deviatoric stress tensor TD for the following stress tensor: ⎡

⎤ 111 T ≡ 20 ⎣ 1 2 3 ⎦ MPa 135 2.37. Show that the stress tensor is symmetric. Hint: Use the principle of moment of momentum on a differential parallelpiped isolated from the body. 2.38. Consider the state of hydrostatic pressure. This state is defined as the state of stress at a certain point such that there is no shear stress on any plane passing through the point. Write a general equation for the stress tensor T for this state of hydrostatic pressure. 2.39. Consider the state of stress given in Example 2.5. Determine the value of T12 given that e1 = 12 (e1 + e2 + e3 ) and e2 = 12 (e1 − e2 − e3 ) 2.40. Show that the maximum shear stress is equal to one-half the difference between the maximum and the minimum principal stresses and the acts on the plane that bisects the angle between the directions of the maximum and minimum principal stresses.


104

Damage Mechanics

2.41. Consider the state of plane stress given in Example 2.6. Determine the maximum shear stress. 2.42. Solve Example 2.6 again for the following state of stress: ⎡

⎤ 10 5 0 T ≡ ⎣ 5 15 0 ⎦ MPa 0 0 0 2.43. Use the state of stress given in Problem 2.42 to solve Problem 2.41 again. 2.44. Give an example of a stress tensor that satisfies the equations of equilibrium. 2.45. Does the following state of stress satisfy the equations of equilibrium. Assume there are no body forces. ⎡

⎤ x1 + x2 −x1 x2 0 T ≡ ⎣ −x1 x2 x1 − x2 0 ⎦ 0 0 x1 x2 2.46. Consider the following state of stress: T11 = x21 + αx22 T12 = −αx1 x2 T13 = 0 T22 = x21 − βx22 T23 = 0 T33 = γx1 x2 Determine the values of α, β, and γ such that the stress tensor T satisfies the equations of equilibrium. Assume that the body forces vanish. 2.47. Define an octahedral stress plane to be a plane which makes equal angles with each of the principal axes of stress. (a) Show that the normal stress on an octahedral plane is given by one-third the first stress invariant.


Elasticity Theory

105

(b) Show that the shear stress on the octahedral plane is given by: Ts =

1 1 [(T1 − T2 )2 + (T2 − T3 )2 + (T1 − T3 )2 ] 2 3

where T1 , T2 , and T3 are the principal stresses. 2.48. Can the following two matrices represent the same stress tensor in two different coordinate systems: ⎡ ⎤ 10 20 0 T1 ≡ ⎣ 20 10 −5 ⎦ MPa 0 −5 30 ⎡

⎤ 10 10 10 T2 ≡ ⎣ 10 30 0 ⎦ MPa 10 0 30 2.49. Consider the state of stress called simple shear where the only nonvanishing stress components are a single pair of shear stresses. For example T12 = T21 = τ and all other Tij = 0. (a) Determine the principal stresses and principal directions for this case of stress. (b) Determine the maximum shear stress and the plane on which it acts for this case of stress. 2.50. Consider the state of stress with only the normal components nonvanishing such that T11 = σ1 , T22 = σ2 , and T33 = σ3 with σ1 > σ2 > σ3 and all other Tij = 0. Determine the maximum shear stress and the plane on which it acts. 2.51. Show that the stress tensor is generally not symmetric if there are body moments per unit volume, as in the case of a polarized anisotropic dielectric solid. 2.52. Consider the stress tensor represented by the following matrix: ⎡ ⎤ α 10 0 T ≡ ⎣ 10 β 30 ⎦ MPa 0 30 γ If the principal values for this stress tensor are T1 = 40 MPa, T2 = 25 MPa, and T3 = 5 MPa, determine the values of α, β, and γ.


106

Damage Mechanics

2.53. Consider the case of plane stress where the stress tensor is generally given as follows: T11 = T11 (x1 , x2 ) T12 = T12 (x1 , x2 ) T13 = 0 T21 = T21 (x1 , x2 ) T22 = T22 (x1 , x2 ) T23 = 0 T31 = 0 T32 = 0 T33 = 0 Write the equation of equilibrium in this special case. 2.54. Consider the special case of the stress given in Problem 2.53. Consider also a scalar function φ(x1 , x2 ) such that: T11 =

∂ 2φ ∂x22

T22 =

∂ 2φ ∂x21

T12 =

∂ 2φ ∂x1 ∂x2

Does this stress distribution satisfy the equations of equilibrium assuming zero body forces. 2.55. Derive the equations of equilibrium in cylindrical coordinates. Hint: Consider a differential volume of material bounded by the three pairs of faces r = r◦ , r = r◦ +dr, θ = θ◦ , θ = θ◦ +dθ, and z = z◦ , z = z◦ +dz, as shown in Figure 2.7.


Elasticity Theory

107

y

Trr + dTrr Trθ + dTrθ Tθθ + dTθθ dr

Tθr + dTθr

Trθ r

Tθr Trr Tθθ

dφ

x

FIGURE 2.7 Infinitesimal element with stresses in cylindrical coordinates.(Lai et al., 1984)

2.4

Linear Elastic Relation

In this section we study the relation between stress and strain in the context of linear elasticity. A constitutive equation relates the stress to relevant quantities of deformation. We assume that deformations are small and the rate of load application has no effect. In general, we can, therefore, write: T = T(E)

(2.57)

with T(0) = 0. We assume the function T(E) to be linear in this section, so we can write the general linear constitutive relation as follows: Tij = Cijkl Ekl


(2.58)

108

Damage Mechanics

where Cijkl are the components of a fourth-order tensor called the elasticity tensor. This tensor is characteristic of anisotropic Hookean elastic solids. A material is called isotropic if its mechanical properties are independent of direction. On the other hand, a material is called anisotropic if its mechanical properties are dependent on direction. Therefore, for an isotropic material, the components of the elasticity tensor Cijkl must be independent of the rotation and reflection of the rectangular basis, i.e., Cijkl = Cijkl for all orthogonal transformations of basis. Such a tensor is called an isotropic tensor. In general, Cijkl can be written in terms of isotropic tensors as follows: Cijkl = λδij δkl + αδik δjl + βδil δjk

(2.59)

where δij δkl , δik δjl , and δil δjk are isotropic tensors. Substituting equation (2.59) into equation (2.58), we obtain: Tij = λeδij + (α + β)Eij

(2.60)

e = Ekk . Let α + β = 2µ, then equation (2.60) becomes: Tij = λeδij + 2µEij

(2.61a)

T = λeI + 2µE

(2.61b)

or

The two material constants λ and µ are called Lame’s constants. In expanded form, equations (2.61) are the constitutive equations for linear isotropic elastic solids, given as follows: T11 = λ(E11 + E22 + E33 ) + 2µE11 T22 = λ(E11 + E22 + E33 ) + 2µE22 T33 = λ(E11 + E22 + E33 ) + 2µE33 T12 = 2µE12 T13 = 2µE13 T23 = 2µE23


Elasticity Theory

109

Example 2.8 Consider the case of uniaxial tension. We define the ratio T11 /E11 as Young’s modulus or modulus of elasticity, denoted by Ey . Show that the following relation holds between the modulus of elasticity Ey , Lame’s constants and Poisson’s ratio: µ=

Ey 2(1 + ν)

Solution First, solve equation (2.61a) for the strain components Eij in terms of the stress components Tij . We obtain: 1 λ Tkk δij Eij = Tij − 2µ 3λ + 2µ

(2.62)

Alternatively, in expanded form we have: E11

1 λ λ+µ T11 = T11 = T11 − 2µ 3λ + 2µ µ(3λ + 2µ)

E22 = E33 = −

λ λ T11 = − E11 2µ(3λ + 2µ) 2(λ + µ)

E12 = E13 = E23 = 0 where we have used T22 = T33 = T13 = T23 = T12 = 0 for the case of uniaxial tension. Therefore, the ratio T11 /E11 , denoted by Ey , is obtained as follows: Ey =

T11 µ(3λ + 2µ) = E11 λ+µ

(2.63)

Also, we obtained the following expression for Poisson’s ratio ν, defined as −E22 /E11 = −E33 /E11 . ν=−

E22 E33 λ =− = E11 E11 2(λ + µ)

(2.64)

Now, eliminate λ from equations (2.63) and (2.64) to obtain: λ=


Ey 2(1 + ν)

(2.65)

110

Damage Mechanics

Example 2.9 Consider the case of simple shear, which corresponds to a state of stress where all the stress components vanish except one pair of off-diagonal elements, like T12 and T21 with T12 = T21 . Define the shear modulus G as the ratio T12 /(2E12 ). Show that the shear modulus G is equal to Lame’s constant µ.

Solution Using the equation (2.61a), we have: T12 = 2µE12 T12 =G 2E12 It should be noted that the shear modulus G is defined as the ratio of the shearing stress in simple shear to the decrease in angle between elements that are initially in the e1− and e2− directions. ∴ µ=

Problems 2.56. Given the following strain matrix: ⎡

⎤ 10 20 10 E ≡ ⎣ 20 50 0 ⎦ × 10−6 10 0 30 Find the components of stress Tij where Lame’s constants are given as λ = 119.2 GPa and µ = 79.2 GPa. 2.57. Show that the principal directions of stress and strain coincide for an isotropic Hookean material. 2.58. Determine the relation between the first invariants of stress and strain for an isotropic elastic material. 2.59. Consider the case of hydrostatic stress defined by T = σI where σ is the constant magnitude of stress. Define the bulk modulus K as the ratio of the hydrostatic normal stress σ, to the unit volume change ∆V /V = e. Show that K=


2µ + 3λ 3

Elasticity Theory

111

2.60. (a) If for a specific material the ratio of the bulk modulus (see Problem 2.59) to Young’s modulus is very large, find the approximate value of Poisson’s ratio. (b) Indicate why the material of part(a) above can be called incompressible. 2.61. Given Young’s modulus Ey = 70 GPa and Poisson’s ratio ν = 0.25, determine Lame’s constants λ and µ. 2.62. Given the data of Problem 2.61, determine the bulk modulus (see Problem 2.59). 2.63. Given the following state of stress at a point: ⎡

⎤ 70 40 30 T ≡ ⎣ 40 50 10 ⎦ MPa 30 10 40 Determine the strain components Eij if Ey = 100 GPa, G = µ = 40 GPa, and ν = 0.30. 2.64. Consider an incompressible material where ν = 1/2 (see Problem 2.60). (a) Show that µ = Ey /3, λ = ∞, K = ∞. (b) Show that Hooke’s law becomes: 1 T = 2µE + Tkk I 3 2.65. Show that the following relations hold among the elastic constants: λ=

Eν (1 + ν)(1 − 2ν)

G=

3KE 9K − E

ν=

3K − E 6K

E=

9K(K − λ) 3K − λ

G = 1 − 2ν λ+G


112

Damage Mechanics λ ν = λ + 2G 1−ν See Problem 2.59 and Example 2.9 for the definitions of K and G, respectively.

2.66. Show that when temperature effects are considered, equation (2.61a) is generalized as follows: Tij = λEkk δij + 2λEij − β(T − T◦ )δij where T◦ is the initial temperature when the body has no stress, T is the new temperature and β is a material constant. 2.67. Consider the case of compression of a rectangular parallelopiped defined by the following stress matrix: ⎡

⎤ −p 0 0 T ≡ ⎣ 0 −p 0 ⎦ 0 0 −p where p > 0 is the magnitude of the inward normal stress. Find expressions for the dilatation and bulk modulus in this case. 2.68. Determine the relation between the principal values of the stress and strain tensors. 2.69. In general, show that if Aij is a symmetric tensor and a is a scalar. then Aij and Aij + aδij have the same principal axes. Determine also the relation between the principal values of the two tensors. 2.70. Show that the following relations hold among the elastic constants: 3Kν 1+ν 3KE µ= 9K − E λ=

E = 3K(1 − 2ν)


3 Isotropic Damage Mechanics

3.1

Introduction

Damage in metals is mainly the process of the initiation and growth of micro-cracks and cavities. At that scale the phenomenon is discontinuous. Kachanov (1958) was the first to introduce a continuous variable related to the density of such defects. This variable has constitutive equations for evolution, written in terms of stress or strain, which may be used in structural calculations in order to predict the initiation of macro-cracks. The three main types of damage are: 1. Ductile damage: the constitutive equations for this type of damage have been formulated by Lemaitre (1984, 1986), Lemaitre and Dufailly (1987), and Voyiadjis and Kattan (1992). Both elastic and elasto-plastic damage effects were considered. 2. Fatigue damage: the constitutive equations for this type of damage have been formulated by Lemaitre (1971), Chaboche (1974), and Lemaitre and Chaboche (1974). 3. Creep damage: the constitutive equations for this type of damage were formulated by Leckie and Hayhurst (1974), Hult (1979), and Lemaitre and Chaboche (1974). This chapter deals with isotropic damage mechanics where the assumption of isotropic damage is often sufficient to give a good prediction of the carrying capacity, the number of cycles or the time to local failure in structural components. In this case, the damage variable is scalar and the calculations are not too difficult because of the scalar nature of the damage variable. In Chapter 4 we will consider anisotropic damage mechanics where the damage variable is tensorial - see Chaboche (1981), Murakami and Ohno (1980), and Krajcinovic and Foneska (1981). Structures, cracks, representative volume elements, macro-cracks, and micro-cracks and cavities represent different scales which have to be carefully defined. The following three definitions are outlined (Lemaitre, 1986).


113

114

Damage Mechanics

1. The micro-scale is the scale at which the mechanisms of strain and damage may be described and understood. The following are three examples: (a) atoms for elasticity. (b) dislocations in crystals for plasticity in metals. (c) inclusions or micro-cracks for damage. It is at this scale that hypotheses are taken in order to write constitutive equations at the macro-scale. 2. The macro-scale is the scale of the representative volume element which is a mathematical representation (or point) small enough to define space partial derivative but large enough to consider that the discrete elementary mechanism of strain and damage are well represented by a mean leading to continuous variables. This scale is usually taken in the order of 0.1 mm for metals, 1 mm for polymers, 10 mm for wood, and 100 mm for concrete (Lemaitre, 1986). A macro-crack just initiated is a crack of that size and the phenomenological constitutive equations govern the behavior at that scale. 3. The structure scale is the scale of mechanical components (mm, cm, dm, m) for which a crack is of the order of one to several millimeters or centimeters. It should be noted that stress, strain or damage as results of structure calculations can describe phenomena only at the macro-scale and structure scale. Nevertheless, it may be an improvement in comparison with classical fracture mechanics which uses more global concepts. Strain energy release rate, contour integrals, and even stress intensity factors result from an overall energetic analysis of the cracked structure. These concepts have obtained enormous success in the prediction of crack behavior when the structures are two-dimensional (plane stress or plane strain), elastic, or in the range of small scale yielding or when the multi-dimensional loading is a proportional loading, and periodic if fatigue crack growth is involved. For more sophisticated problems it is difficult to use classical fracture mechanics concepts mainly because of the following effects (Lemaitre, 1986): 1. Effects of large-scale yielding plasticity, overload retardation effects in fatigue, and ductile rupture due to large deformation. 2. Effects of time-dependent behavior, creep crack growth, and creepfatigue interaction.


Isotropic Damage Mechanics

115

3. Three-dimensional effects, cracks loaded in mixed modes, and evolution of crack front shape when loading is non-proportional. 4. Effects of damage, short cracks in metals, multiple cracking in concrete, and delamination of composites. In damage mechanics and using continuous concepts, the crack tip is a process zone in which damage increases until the rigidity and strength vanish. This gives rise to a continuous definition of a crack (at the structure scale). A crack is therefore defined as a flat zone of high gradients of rigidity and strength in which the critical conditions of damage have been reached. It is then considered that the evolution of the crack is the evolution of the damaged zone as calculated element by element with re-calculation of the state of stress and strain (Lemaitre, 1986). For more details, the reader is referred to Chaboche (1988 a,b), Chaboche and Lesne (1988), Chaboche (1993), Chow and Wang (1987 a,b, 1989).

3.2

Damage Variables

A damage variable can be defined within the context of the two categories of damage characteristics which are commonly used. The first category does not characterize the damage itself where the value of the damage variable determines only the damage. The second category introduces damage variables that are associated with a physical definition of damage. The first three items below correspond to the first category while the remaining three items correspond to the second category. In general, damage variables can be defined in terms of each of the following quantities (Lemaitre, 1986): 1. The stress: using a damage equivalent stress σ ∗ deduced from a thermodynamic approach of damage, where σ ∗ is given by (Lemaitre and Baptiste, 1982): ∗

σ = σeq.

σH 2 2 (1 + υ) + 3(1 − 2υ)( ) 3 σeq.

(3.1)

where υ is Poisson’s ratio, σeq. is the von Mises equivalent stress given by: σeq. =


3 (σij − σH δij )(σij − σH δij ) 2

(3.2)

116

Damage Mechanics and σH is the hydrostatic stress given by: 1 σKK 3

σH =

(3.3)

The criterion for crack initiation is taken as σ ∗ = σc where σc is a critical stress level dependent on the characteristics of each material. 2. The strain: using the accumulated plastic strain in the sense of von Mises as follows: t p= 0

2 p p

˙ ˙ dt 3 ij ij

(3.4)

3. The plastic strain energy: used as follows:

t

wp = 0

σij ˙pij dt

(3.5)

4. The porosity: used as the relative volume of cavities for ductile damage as follows (Rousselier, 1981): P =

δv δV

(3.6)

where v is the volume of cavities and V is the total volume. 5. The radius of the cavities as demonstrated by Mudry (1983). 6. The relative area of micro-cracks and intersections of cavities in any plane oriented by its normal n as follows (Lemaitre and Chaboche, 1985): φ(n) =

δSφ δS

(3.7)

where Sφ is the area of micro-cracks and intersections and S is the total area of the cross-section. With a correction for micro-stress concentrations and interactions of defects this concept gives rise to a continuous variable suitable for continuum mechanics. For this reason, this is the definition of the scalar damage variable used in this book.



117

If damage is considered as isotropic (Kachanov, 1958), then the damage variable φ is adopted as a scalar. Otherwise, if anisotropic damage is considered, then a damage vector φ (Krajcinovic and Foneska, 1981) or a second-order or a fourth-order damage tensor is employed (Betten, 1981; Chaboche, 1984; Leckie and Onat, 1980; Murakami and Ohno, 1981). Restricting ourselves to isotropic damage in this chapter, then φ = 0 characterizes the virgin (undamaged) state, while φ = φc ≤ 1 characterizes the initiation of a macro-crack. The parameter φc is a critical value for the damage variable usually taken between 0.2 and 0.8 for engineering materials. See the reference by Lemaitre and Chaboche (1994).

3.3

Effective Stress

We will first state the hypothesis of isotropy. Isotropic damage consists of cracks and cavities with an orientation distributed uniformly in all directions. In this case, the damage variable does not depend on the orientation n and the damaged state is completely characterized by the scalar φ. In this chapter we will limit ourselves to the case of isotropic damage where φn = φ for each vector n (see Figure 3.1). The introduction of a damage variable which represents a surface density of discontinuities in the material leads directly to the concept of effective stress, i.e., to the stress calculated over the section which effectively resists the forces. Consider a damaged solid in which an element of finite volume has been isolated, of a sufficiently large size with respect to the inhomogeneities of the medium, and imagine that this element has been grossly enlarged (see Figure 3.1). Let S be the area of a section of the volume element identified by its normal n. On this section, cracks and cavities which constitute the damage leave traces of different forms. Let S¯ be the effective area of resistance (S¯ < S) taking account of the area of these traces, stress concentrations in the neighborhood of geometric discontinuities, and the interactions between the neighboring defects. Let Sφ be the difference: Sφ = S − S¯

(3.8)

It should be noted that Sφ is the total area of the defect traces corrected for stress concentrations and interactions. We define the scalar damage variable φ (φ ≡ φn ) as follows:


118

Damage Mechanics

n n S

Sφ

FIGURE 3.1 A damaged element showing the areas S and Sφ along with the normal vector n.

φ=

Sφ S

(3.9)

From a physical point of view, the damage variable is, therefore, the relative (or corrected) area of cracks and cavities cut by a plane normal to the direction n. From the mathematical point of view, as S tends to 0, the variable φ (or φn ) is the (corrected) surface density of the discontinuities of the matter in the plane normal to n. In the uniaxial case, if F is the applied force on a section of the representative volume element, σ = FS is the usual stress satisfying equilibrium. In the presence of isotropic damage, φ, the effective area of resistance is obtained as follows using equations (3.8) and (3.9): S¯ = S − Sφ = S(1 − φ)

(3.10)

Taking σS = σ ¯ S¯ along the two configurations, and substituting equation (3.10), we obtain the following equation for the effective stress σ ¯:



119

σ (3.11) 1−φ It is clear that σ ¯ ≥ σ and that σ ¯ = σ for a virgin material (φ = 0), and σ ¯ −→ ∞ at the moment of fracture (φ −→ 1). In the case of multi-axial isotropic damage, the ratio S/S¯ does not depend on the orientation of the normal n and the operator (1 − φ) can be applied to all the components of the stress tensor. We will, therefore, have the ¯ following equation for the effective stress tensor σ: σ ¯=

σ (3.12) 1−φ We now state the principle of strain equivalence. We assume that the deformation behavior of the material is only affected by damage in the form of effective stress. Any deformation behavior, whether uniaxial or multiaxial, of a damaged material is represented by the constitutive laws of the virgin material in which the usual stress is replaced by the effective stress (see Figure 3.2). For example, the uniaxial linear elastic law of a damaged material is written as follows: ¯= σ

σ σ ¯

e = ¯ = E (1 − φ)E¯

(3.13)

¯ is Young’s modulus. This constitutes a nonrigorous hypothesis where E which assumes that all the different behaviors (elasticity, plasticity, viscoplasticity) are affected in the same way by the surface density of the damage defects. However, its simplicity allows the establishment of a coherent and efficient formalism. By applying the concept of effective stress at the instant of fracture by interatomic decohesion, we define the critical value of damage φc , as that corresponding to the occurrence of this phenomenon. If σ ¯u is the uniaxial stress at fracture by decohesion and σu is the usual ultimate fracture stress, we have (see equation (3.11)): σu 1 − φc Solving equation (3.14) for φc , we obtain: σ ¯u =

φc = 1 −

σu σ ¯u

(3.14)

(3.15)

¯ ¯ The physics of solids shows that σ ¯u is of the order of E/50 - E/20; for ¯ ¯ common materials σu is of the order of E/100 - E/250, and φc is therefore of the order of 0.5 - 0.9. This allows us to neglect the term (1 − φc )x with x >> 1, a term which often appears in calculation, in comparison to 1.


120

Damage Mechanics σ

σ

φ

L

φ=0

σ (a)

σ (c)

(b)

E = F(σ, t)

E = F(σ, t)

FIGURE 3.2 Different configurations of the material: (a) virgin material, (b) damaged material, (c) equivalent virgin material. Note that the function F is the same used for all configurations.

Example 3.1 Let Y be the thermodynamic variable associated with the damage variable φ in the sense that Y φ˙ is the power dissipated in the damage process. Consider a thermodynamic potential Ψ quadratic with respect to the elastic strain e and linear in (1 − φ). Show that: Y =

σ∗ 2 ∂Ψ =− 2 ∂φ E (1 − φ)2

(3.16)

where σ ∗ is given in equation (3.1). Solution The thermodynamic potential Ψ is written as follows: Ψ = (1 − φ) 2e Substitute equation (3.13) into the above equation to obtain:


(3.17)


121

Ψ=

σ∗ 2 (1 − φ)E¯ 2

where σ is replaced by σ ∗ in the equation. Next, we take the derivative of Ψ with respect to φ to obtain: Y =

∂Ψ σ∗ 2 =− ∂φ (1 − φ)2 E¯ 2

Example 3.2 Sidoroff (1981) proposed the hypothesis of elastic energy equivalence to be used instead of the hypothesis of strain equivalence. This new hypothesis assumes that the elastic energy for a damaged material is equivalent in form to that of the undamaged (effective) material except that the stress is replaced by the effective stress in the energy formulation. Use the hypothesis of elastic energy equivalence to show that: E (3.18) φ=1− ¯ E ¯ is the effective modulus of elasticity and E is the modulus of where E elasticity of the damaged material. Solution For the uniaxial tension case, the constitutive relation is Hooke’s law of linear elasticity given by: σ = E e

(3.19)

The same linear elastic constitutive relation applies to the undamaged (effective) state, i.e., ¯ e σ ¯ = E¯

(3.20)

¯ are the effective counterparts of e and E, respectively. where ¯e and E The hypothesis of elastic energy equivalence is written mathematically as follows: 1 1 σ e = σ ¯ ¯e 2 2

(3.21)

where the elastic strain energy 12 σ e is equated to the effective elastic strain energy 12 σ ¯ ¯e .


122

Damage Mechanics

Substituting equation (3.11) into equation (3.21) and simplifying, we obtain the following relation between the elastic strain e and the effective elastic strain ¯e : ¯ e = (1 − φ) e

(3.22)

We next substitute equations (3.11) and (3.22) into equation (3.20), simplify the result and compare it with equation (3.19) to obtain: ¯ − φ)2 E = E(1

(3.23)

Equation (3.23) represents the transformation law for the modulus of elasticity. Solving equation (3.23) for φ, we finally obtain the desired result as follows: E φ=1− ¯ E

Problems 3.1. Derive equation (3.13). Which hypothesis is used in the derivation. 3.2. Give an example for each one of the following damage types: (a) ductile damage, (b) fatigue damage, and (c) creep damage. 3.3. Why do you think the macro-scale is taken in the order of 0.1 mm for metals but 10 mm for wood. 3.4. Derive equation (3.1). Hint: See the paper by Lemaitre and Baptiste, 1982. 3.5. Define a new damage variable based on the radius of cavities. Hint: See the paper by Mudry, 1983. 3.6. Plot a graph showing the relation between σ ¯ and φ assuming that the stress σ is constant. See equation (3.11). 3.7. Why is the critical value of the damage variable φc usually taken between 0.5 and 0.9. 3.8. Compare the transformation laws for the elastic strain and the modulus of elasticity in the case of using (a) the hypothesis of strain equivalence, (b) the hypothesis of elastic energy equivalence. 3.9. How will equation (3.18) change if the hypothesis of elastic energy equivalence is replaced with the hypothesis of strain equivalence.



123

3.10. Suppose that the damage in a cylinder under uniaxial tension is composed entirely of voids and cracks. Let S v be the area of voids and S c be the area of cracks. The total area S is then given by: S = S¯ + S v + S c Show that, in this case, the damage variable φ is given by: φ = φv + φc − φv φc where φv is the damage variable due to voids and φc is the damage variable due to cracks, both defined as follows: Sv φv = ¯ S + Sv Sc φc = ¯ S + Sc 3.11. Describe how equation (3.18) can be used to determine the damage variable φ experimentally. 3.12. Derive the transformation law for the compliance C where C = 1/E in the case of uniaxial tension. 3.13. Show that the critical value of the damage variable φc can be calculated using the following formula: σ∗ φc = 1 − ¯ √ E −Yc ¯ is the modulus of elasticity, and where σ ∗ is given in equation (3.1), E Yc is the critical value of the thermodynamic variable Y associated with the damage variable φ. See Example 3.1. 3.14. Consider the density of elastic strain energy W e defined by: dW e = σd e where the operator “d” indicates an incremental quantity. Show that the thermodynamic variable Y associated with the damage variable φ is given by: Y =−


1 dW e 2 dφ

124

3.4

Damage Mechanics

Damage Evolution

There are several approaches in the literature on the topic of evolution of damage and the proper form of the kinetic equation of the damage variable. Kachanov (1986) proposed an evolution equation of damage based on a power law with two independent material constants. However, the resulting kinetic equation for the damage variable evolution is complicated and difficult to solve. Therefore, a more rational approach based on energy considerations will be adopted in this book. The approach followed will depend on the introduction of a damage strengthening criterion in terms of a scalar function g, and a generalized thermodynamic force Y that corresponds to the damage variable φ (Lemaitre, 1985; Lee et al, 1985; Voyiadjis and Kattan, 1999). Substituting equations (3.20) and (3.22) into the right-hand-side of equation (3.21), we obtain the elastic strain energy U in the damaged state of the material as follows: 1¯ E(1 − φ)2 e2 (3.24) 2 in which E¯ is constant. Therefore, the incremental elastic strain energy dU is obtained by differentiating equation (3.24) as follows: U=

¯ − φ) e2 dφ ¯ − φ)2 e d e − E(1 dU = E(1

(3.25)

The generalized thermodynamic force Y associated with the damage variable φ is thus defined by: Y =

dU ¯ − φ) e2 = −E(1 dφ

(3.26)

Let g(Y, L) be the damage function (criterion) as proposed by Lee et al (1985), where L ≡ L(l) is a damage strengthening parameter that is a function of the “overall” damage parameter l. In this case, the scalar function g takes the following form: 1 2 Y − L(l) ≡ 0 (3.27) 2 The damage strengthening criterion defined by equation (3.27) is similar to the von Mises yield criterion in the theory of plasticity. In order to derive a normality rule for the evolution of damage, we first start with the power of dissipation Π which is given by: g(Y, L) =

Π = −Y dφ − Ldl


(3.28)


125

where the “d” in front of a variable indicates the incremental quantity of the variable. The problem is to extremize Π subject to the condition g = 0. Using the mathematical theory of functions of several variables, we introduce the Lagrange multiplier dλ, and form the objective function Ψ(Y, L) such that: Ψ = Π − dλ.g

(3.29)

The problem reduces to extremizing the function Ψ. For this purpose, the two necessary conditions are ∂Ψ/∂Y = 0 and ∂Ψ/∂L = 0. Using these two conditions, along with equations (3.28) and (3.29), we obtain: dφ = −dλ

∂g ∂Y

(3.30a)

dl = −dλ

∂g ∂L

(3.30b)

Substituting for g from equation (3.27) into equation (3.30b), one concludes directly that dλ = dl. Substituting this into equation (3.30a), along with using equation (3.27), we obtain: dφ = −dλ.Y

(3.31)

In order to solve the differential equation (3.31), we must first find an expression for the Lagrange multiplier dλ. This can be done by invoking the consistency condition dg = 0. Applying this condition to equation (3.27), we obtain: ∂g ∂g dY + dL = 0 ∂Y ∂L

(3.32)

∂g ∂g Substituting for ∂Y and ∂L from equation (3.27) and for dL = dl( ∂L ∂l ) using the chain rule of differentiation, and solving for dl, we obtain:

dl = dλ =

Y dY ∂L/∂l

(3.33)

Substituting the above expression of dλ into equation (3.31), we obtain the kinetic (evolution) equation of damage as follows: dφ =

−1 Y 2 dY ∂L/∂l

with the initial condition that φ = 0 when Y = 0.


(3.34)

126

Damage Mechanics

Example 3.3 Derive the following relation between the damage variable φ and elastic strain e : ¯3 6 E φ

e = ∂L (1 − φ)3 3( ∂l )

(3.35)

Solution Differentiate the expression of Y in equation (3.26) to obtain: ¯ e [ e dφ − 2d e (1 − φ)] dY = E

(3.36)

Next, substitute the expressions of Y and dY of equations (3.26) and (3.36), respectively, into equation (3.34), to obtain the strain-damage differential equation as follows: dφ =

1 ¯ 3 e5 (1 − φ)2 [2d e (1 − φ) − e dφ] E (∂L/∂l)

(3.37)

The above differential equation can be solved easily by the simple change 2 of variables x = e (1 − φ) and noting that the expression on the right¯ 3 x2 dx/(∂L/∂l). Perform hand-side of the equation (3.37) is nothing but E the integration with the initial condition that φ = 0 when e = 0 to obtain the desired formula: ¯3 6 E φ

e = 3 (1 − φ) 3(∂L/∂l) One should note that an initial condition involving an initial damage value φ◦ could have been used, i.e., φ = φ◦ when e = 0.

Problems Determine an evolution equation of damage based on a power law with two independent material constants as proposed by Kachanov in 1986. Solve the differential equation (3.34) for φ in terms of Y. Assume a linear function for L(l) in the form L(l) = cl + d, where c and d are constants. Plot the resulting formula and show that you obtain a cubic curve. Solve the differential equation (3.37) again but this time using the initial condition φ = φ◦ = constant when e = 0. Use equations (3.26) and (3.34) to derive equation (3.35) directly. Hint: Use the result of Problem 3.16 above.



127

Plot the relation between the damage variable φ and elastic strain e obtained in equation (3.35). The equations of damage evolution given in Section 3.4 were obtained based on the hypothesis of elastic energy equivalence. Obtain alternative but similar equations of damage evolution using the hypothesis of strain equivalence. Consider the following damage function (criterion) g which does not employ the thermodynamic force Y in the formulation: 1 2 σ ¯ − L(l) ≡ 0 (3.38) 2 Use this new function instead of equation (3.27) to derive a new damage evolution equation to be used instead of equation (3.34). g=

Obtain a new relation between the damage variable φ and elastic strain

e based on the new damage function (criterion) g given in Problem 3.21 above. Consider a composite cylindrical bar made of a matrix and fibers of two different materials. Let E M and E F be the moduli of elasticity for the matrix and fibers, respectively. Let also σ M and σ F be the stresses in the matrix and fibers, respectively. Then the total uniaxial stress σ in the bar is given by the following rule of mixtures: σ = cM σ M + cF σ F where cM and cF are the matrix and fiber volume (or area) fractions, respectively. 3.1. Define two new scalar damage variables φM and φF , for the matrix and fibers, respectively. 3.2. Determine two appropriate evolution equations for the two damage variables defined in part (a). 3.3. Determine a relation between the global damage variable φ and the two local damage variables φM and φF .


4 Kinematic Description of Damage

4.1

Introduction

In 1958, Kachanov (1958) introduced the concept of effective stress in damaged materials. This pioneering work started the subject that is now known as continuum damage mechanics. Research in this area has steadily grown and reached a stage that warrants its use in today’s engineering applications. Continuum damage mechanics is now widely used in different areas including brittle failure (Krajcinovic, 1983, 1985; Krajcinovic and Foneska, 1981; Lubarda et at., 1994; Ju and Lee, 1991; Lee and Ju, 1991; Ju and Chen, 1994a,b), ductile failure (Lemaitre, 1985, 1986; Chaboche, 1979, 1981, 1988a,b; Chow and Wang, 1987), composite materials (Allen et al., 1987; Boyd et al., 1983; Voyiadjis and Kattan, 1993, Voyiadjis and Park, 1995a, b) and fatigue (Chow and Wei, 1991 ). In this theory, a continuous damage variable is defined and used to represent degradation of the material which reflects various types of damage at the micro-scale level like nucleation and growth of voids, cavities, micro-cracks, and other microscopic defects. In continuum damage mechanics, the effective stress tensor is usually not symmetric. This leads to a complicated theory of damage mechanics involving micropolar media and the Cosserat continuum. Therefore, to avoid such a theory, symmetrization of the effective stress tensor is used to formulate a continuum damage theory in the classical sense (Lee et al., 1986; Sidoroff, 1979; Cordebois and Sidoroff, 1982; Murakami and Ohno, 1980; Betten, 1983; Lu and Chow, 1990). A linear transformation tensor, defined as a fourth-order damage effect tensor is used to symmetrize the effective stress tensor. The kinetics of damage is well defined presently through the effective stress concept. However, the kinematics of the deformation with damage is only considered indirectly and is only limited to the small strain theory based on the hypothesis of the strain equivalence (Lemaitre and Chaboche, 1978) or energy equivalence (Sideroff, 1980). The finite deformation damage models by Ju (1989) and Zbib (1993) emphasize that “added flexibility”


129

130

Damage Mechanics

due to the existence of microcracks or microvoids is already embedded in the deformation gradient implicitly. Murakami (1988) presented the kinematics of damage deformation using the second-order damage tensor. However, the lack of an explicit formulation for the kinematics of finite deformation with damage leads to the failure in obtaining an explicit derivation of the kinematics that directly consider the damage deformation. The kinematics of damage is described here explicitly by considering damage directly in the kinematic field using the second-order damage tensor. The deformation gradient of damage is defined using the second-order damage tensor based on the geometically symmetrized effective stress concept (using a fourth-order tensor). The Green deformation tensor of the elastic damage deformation is also derived. For a detailed review of the principles of continuum damage machanics as used in this chapter, the reader is referred to the works of Kachanov (1958), Lemaitre (1985, 1986), Krajcinovic (1985), Lubarda and Krajcinovic (1995), Chaboche (1981, 1988a, b), Murakami (1988), Sidoroff (1979, 1980), and Voyiadjis and Kattan (1992, 1999). The following sections are based mainly on the work of Park and Voyiadjis (1998).

4.2

Theoretical Preliminaries

Referring to Figure 4.1, the initial undeformed configuration of the body is denoted by C0 , while the elastic damage deformed configuration after the body is subjected to a set of external agencies is denoted by C. The body in configuration C0 undergoes a sequence of deformations starting with an elastic deformation without damage, followed by a damage deformation. This is indicated by path I in Figure 4.1. The configuration denoted by C e implies the elastic deformed configuration. The initial undeformed body may have a pre-existing damage state. A fictitious effective configuration for the body denoted by C¯ is assumed to be obtained from C by fictitiously removing all the damage that the body has undergone. This is the fictitious effective configuration which is based on the effective stress concept. In this configuration, the body has only deformed elastically without damage. In addition to the fictitious ef¯ the initial fictitious effective configuration denoted fective configuration C, by C0 is defined by removing the initial damage from the initial undeformed configuration of the body. In the case of no initial damage existing in the undeformed body, the initial fictitious effective configuration is identical to the initial undeformed configuration. This chapter is limited to elastic strains with damage.


Kinematic Description of Damage

131

FIGURE 4.1 Schematic representation of elastic damage deformation configurations. (Park and Voyiadjis, 1998)

4.3

Description of Damage State

The damage state can be described using an even order tensor (Leckie, 1993; Onat, 1986; and Betten, 1986). Ju (1990) pointed out that even for isotropic damage one should employ a damage tensor (not a scalar damage variable) to characterize the state of damage in materials. However, the damage generally is anisotropic due to the external agency condition or the material nature itself. Although the fourth-order damage tensor can be used directly as a linear transformation tensor to define the effective stress tensor, it is not easy to characterize physically the fourth-order damage tensor compared to the second-order damage tensor. In this chapter, the damage is considered as a symmetric second-order tensor. The second-


132

Damage Mechanics

order damage tensor is given by (Murakami 1983) as follows:

φij =

3

ˆ ki n ˆ kj (no sum in k) φˆk n

(4.1)

k=1

φij = bir bjs φˆrs

(4.2)

where n ˆ k is an eigenvector corresponding to the eigenvalue, φˆk , of the damage tensor, φ. The damage tensor in the coordinate system that coincides with the three orthogonal principal directions of the damage tensor, φˆrs , in equation (4.2) is of diagonal form and is given by ⎤ ⎡ˆ φ1 0 0 φîj = ⎣ 0 φˆ2 0 ⎦ 0 0 φˆ3

(4.3)

and the second order transformation tensor b is given by ⎤ n11 n12 n13 = ⎣n21 n22 n23 ⎦ n31 n32 n33 ⎡

bir

(4.4)

This proper orthogonal transformation tensor requires that bij bkj = δik

(4.5)

where δik is a Kronecker delta and the determinant of the matrix [b] is given by |[b]| = 1

(4.6)

Voyiadjis and Venson (1995) quantified the physical values of the eigenvalues φˆk (k = 1,2,3) and the second-order damage tensor φ for the unidirectional fibrous composite by measuring the crack density with the assumption that one of the eigendirections of the damage tensor coincides with the fiber direction provided that the load is applied uniformly along the fiber direction. This introduces a distinct kinematic measure of damage which is complementary to the deformation kinematic measure of strain. A thermodynamically consistent evolution equation for the damage tensor φ together with a generalized thermodynamic force (Chaboche 1977) conjugate to the damage tensor is presented in the paper by Voyiadjis and Park (1995a,b).



4.4

133

Fourth-Order Anisotropic Damage Effect Tensor

In a general state of deformation and damage, the effective stress tensor ¯ is related to the stress tensor σ by the following linear transformation σ (Murakami and Ohno 1980): σ ¯ij = Mikjl σkl

(4.7)

¯ = Mσ σ

(4.8)

where σ is the Cauchy stress tensor and M is a fourth-order linear transformation operator called the damage effect tensor. Depending on the form used for M, it is very clear from equation (4.8) that the effective stress ¯ is generally not symmetric. Using a nonsymmetric effective stress tensor σ tensor as given by equation (4.8) to formulate a constitutive model will result in the introduction of the Cosserat and a micropolar continuum. However, the use of such complicated mechanics can be easily avoided if the proper fourth-order linear transformation tensor is formulated in order to symmetrize the effective stress tensor. Such a linear transformation tensor called the damage effect tensor is obtained in the literature (Lee at al., 1986; Sidoroff, 1979) using symmetrization methods. The effective stress tensor is symmetrized using the following expressions by Cordebois and Sidoroff (1979) and Lee et al. (1986). σ ¯ij = (δik − φik )−1/2 σkl (δjl − φjl )−1/2

(4.9)

σ ¯ij = 12 [(δik − φik )−1 σkl δjl + δik σkl (δjl − φjl )−1 ]

(4.10)

σij = 12 [(δik − φik )¯ σkl δjl + δik σ ¯kl (δjl − φjl )]

(4.11)

The fourth-order damage effect tensors corresponding to equations (4.9), (4.10) and (4.11) are defined such as Mikjl = (δik − φik )−1/2 (δjl − φjl )−1/2

(4.12)

Mikjl = 12 [(δik − φik )−1 δjl + δik (δjl − φjl )−1 ]

(4.13)

Mikjl = 2[(δik − φik )δjl + δik (δjl − φjl )]−1

(4.14)

Another approach is that of the damage effect tensor using the fourth order damage tensor ψ as defined by Chaboche (1979)


134

Damage Mechanics Mikjl = (Iikjl − ψikjl )

(4.15)

where Iikjl is a fourth order identity tensor and is given by Iikjl = 12 (δij δkl + δil δkj )

(4.16)

However, it is not easy to characterize physically the fourth order damage tensor ψijkl as opposed to the second-order damage tensor φij . For the case of isotropic damage, the fourth order damage tensor is defined by Ju (1990) as follows ψijkl = d1 δik δjl + d2 Iikjl

(4.17)

where d1 and d2 are scalars (dependent or independent) damage variables. In order to describe the kinematics of damage, the physical meaning of the fourth-order damage effect tensor should be interpreted and not merely given as the symmetrization of the effective stress. In this chapter, the fourth-order damage effect tensor given by equation (4.12) will be used because of its geometrical symmetrization of the effective stress (Cordebois and Sidoroff, 1979). However, it is very difficult to obtain the explicit representation of (δik − φik )−1/2 . The explicit representation of the fourthorder damage effect tensor M using the second-order damage tensor φ is of particular importance in the implementation of the constitutive modeling of damage mechanics. Therefore, the damage effect tensor M of equation (4.12) should be obtained using the coordinate transformation of the principal damage direction coordinate system. Thus the fourth-order damage effect tensor given by equation (4.12) can be written as ˆ mnpq Mikjl = bmi bnj bpk bql M

(4.18)

ˆ is a fourth-order damage effect tensor with reference to the prinwhere M cipal damage direction coordinate system. The fourth-order damage effect ˆ can be written as follows: tensor M ˆ mpnq = a M ˆmp a ˆnq

(4.19)

where the second-order tensor a of the principal damage direction coordinate system is given by a ˆmp = [δmp − φˆmp ]−1/2 ⎡ 1 √ 0 0 ˆ ⎢ 1−φ1 √ 1 0 0 =⎢ ˆ2 ⎣ 1−φ √1 0 0

ˆ3 1−φ


⎤ ⎥ ⎥ ⎦

(4.20)


135

Substituting equation (4.19) into equation (4.18), one obtains the following relation ˆmp a ˆnq Mikjl = bmi bnj bpk bql a = aik ajl

(4.21)

Using equation (4.21), a second-order tensor a is defined as follows: aik = bmi bpk a ˆmp

(4.22)

The matrix form of equation (4.22) is as follows: [a] = [b]T [ˆ a][b] ⎡

b11 b11 b21 b21 b31 b31 √ b11 b12 b21 b22 b31 b32 √ +√ +√ +√ +√ ˆ1 ˆ2 ˆ3 ˆ1 ˆ2 ˆ3 φ 1−φ 1−φ 1−φ 1−φ 1−φ ⎢ b121−b11 b22 b21 b32 b31 √ b12 b12 b22 b22 b32 b32 √ √ √ √ √ ⎢ + + + + [a] = ⎣ 1−φˆ ˆ2 ˆ3 ˆ1 ˆ2 ˆ3 1−φ 1−φ 1−φ 1−φ 1−φ 1 b13 b11 b23 b21 b33 b31 √ b13 b12 b23 b22 b33 b32 √ √ √ √ √ + + + + ˆ ˆ ˆ ˆ ˆ ˆ 1−φ1

1−φ2

1−φ3

1−φ1

b11 b13 b21 b23 b31 b33 √ +√ +√ ˆ ˆ ˆ

1−φ2

1−φ1 1−φ2 1−φ3 b12 b13 b22 b23 b32 b33 ⎥ √ √ √ ⎥ + + ˆ1 ˆ2 ˆ3 ⎦ 1−φ 1−φ 1−φ b b b b b b √13 13 + √23 23 + √33 33 ˆ ˆ ˆ 1−φ1

4.5

1−φ2

1−φ3

⎤ (4.23)

1−φ3

Kinematic Description of Elastic-Damage Deformation

A schematic drawing representing the kinematics of finite elastic deformation and damage is shown in Figure 4.1. C0 is the initial undeformed configuration of the body which may have initial damage in the material. C represents the final elastically deformed and damaged configuration of the body. The configuration C¯0 represents the initial configuration of the body that is obtained by fictitiously removing the initial damage from the C0 configuration. If the initial configuration is undamaged then there is no difference between configurations C0 and C¯0 . Configuration C¯ is obtained by fictitiously removing the damage from configuration C. Considering path I the deformation gradient referred to the undeformed configuration, C0 , denoted by F is polarly decomposed into the elastic deformation gradient denoted by Fe and the damage deformation gradient denoted by Fd such that F = Fe Fd (4.24)


136

Damage Mechanics

The Green deformation tensor of the elastic damage deformation can be obtained through either path I or path II as shown in Figure 4.1. Path I gives the Green deformation tensor as follows: G = FT F T

T

= Fd Fe Fe Fd

(4.25)

Considering path II the fictitious initial damage Green deformation tensor, ¯ d , and the fictitious damage Green deformation tensor, G ¯ d , are defined G 0 as follows: ¯d ¯d = F ¯ dT F G (4.26) 0 0 0 and ¯d = F ¯ dT F ¯d G

(4.27)

¯ d are the fictitious effective initial damage deforma¯ d and F respectively. F 0 tion and the fictitious effective damage deformation gradients, respectively. The deformation gradient and the Green deformation tensor used in following path II may appear initially to be of the following forms: ¯ eF ¯d ¯ d0 F F=F

(4.28)

¯ dT F ¯ eT F ¯ dT F ¯ dF ¯ eF ¯d G=F 0 0 0

(4.29)

and

respectively. However, due to the fictitious removal of damage from configurations C0 and C, the deformation gradient and the Green deformation tensor cannot be expressed by equations (4.28) and (4.29). Since the two ¯ are obtained by fictitiously removing effective configurations, C¯0 and C, damage from the real configurations, therefore the difference between the two fictitious damage deformation tensors needs to be subtracted from the Green deformation tensor given by equation (4.29). Thus, the resulting Green deformation tensor in considering path II is given by ¯ eT F ¯ dT F ¯ dF ¯ eF ¯ d − (G ¯d −G ¯ d) ¯ dT F G=F 0 0 0 0 ¯ eT F ¯ dT F ¯ dF ¯ eF ¯ d − (F ¯d − F ¯ d) ¯ dT F ¯ dT F ¯ dT F =F 0

0

0

0

0

(4.30)

It should be noted that the deformation gradients following paths I and II are not related directly. However, the Green deformation tensors may be obtained following paths I or II. This is clearly indicated in equation ¯ dT F ¯ d ) due to the fictitious removal of (4.30) where one needs to remove (F damage from the material. However, one needs to add the initial fictitiously removed deformation due to damage. Both equations (4.25) and (4.30)



137

show that the Green deformation tensor can be expressed by either path I or path II, respectively. In addition, the effective Green deformation tensor of path II is the counterpart of the effective stress field and is defined as follows: ¯ =F ¯ eT F ¯e G

(4.31)

For simplicity, one assumes that no initial damage exists in the initial undeformed body. Consequently, one obtains the following relation such that ¯ d0 = I ¯ dT F (4.32) F ¯ e = Fe F

(4.33)

where I is a second order identity tensor. Using equations (4..31), (4.32), (4.33), one obtains the Green deformation tensor relating paths I and II as follows

or

T ¯ d G = Fd GF

(4.34)

¯F ¯ d − (F ¯ d − I) ¯ dT F ¯ dT G G=F

(4.35)

From equation (4.35), one obtains the effective Green deformation tensor as follows ¯ d − I)]F ¯ =F ¯ d−T [G + (F ¯ dT F ¯ d−1 G ¯ d−1 + I ¯ d−T GF ¯ d−1 − F ¯ d−T F =F

(4.36)

Equating equations (4.34) and (4.35), one obtains the following relationship ¯ dT G ¯F ¯d = F ¯F ¯d − F ¯d + I ¯ dT G ¯ dT F F

(4.37)

The Green-Saint-Venant strain tensor termed here the strain tensor is defined as follows: = 12 (G − I)

(4.38)

The corresponding effective strain tensor of the counterpart of the effective stress is defined such that ¯ − I) ¯ = 12 (G


(4.39)

138

Damage Mechanics

Substituting equation (4.36) into equation (4.39), one obtains the effective strain tensor in terms of the elastic-damage Green tensor and the fictitious effective damage gradient such that ¯ d−T (G − I)F ¯ d−1 ¯ = 12 F

(4.40)

Finally one obtains the relation between ¯ and using equations (4.38) and (4.40) such that ¯ d−1 ¯ d−T F ¯ = F

(4.41)

Alternatively, the strain tensor is given by ¯d ¯ dT ¯F ¯ = F

(4.42)

The approach used here provides a relation between the effective strain and the damage elastic strain applicable also to finite strains and is not confined to small strains as in the case of the strain equivalence or the strain energy equivalence approach. Since the fictitious effective deformed ¯ is obtained by removing the damage from the configuration denoted by C, real deformed configuration denoted by C, the fictitious effective deformed ¯ is similarly obtained as follows: volume denoted by Ω ¯ = Ω − Ωd Ω = (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 ) Ω

(4.43)

or ¯ Ω = J¯d Ω

(4.44) where Ω is the deformed volume, Ω is the damage volume, and J¯d is the Jacobian of the damage deformation. The Jacobian of the damage deformation is given by d

1 J¯d = (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 )

(4.45)

However, the Jacobian of the damage is defined such that ¯ d| |G ¯ dT F ¯ d| = |F ¯ dT ||F ¯ d| = |F

J¯d =


(4.46)


139

The determinant of the matrix [a] in equation (4.27) is given by |[a]| = |[b]|T |[ˆ a]||[b]| = |[ˆ a]| 1 = (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 )

(4.47)

Thus one assumes the following relation similar to equation (7) without loss of generality ˆ ikjl σ σ ¯ij = M ˆkl =a îk a ˆjl σ ˆkl d d = Fˆ¯ ik Fˆ¯ jl σ ˆkl

(4.48)

for stresses coinciding with the principal directions of damage. Consequently one obtains d Fˆ¯ ij = a îj (4.49) and F¯ijd = aij

(4.50)

Although the identity is established between J¯d and |a|, this is not sufficient to demonstrate the validity of equation (4.49). Equation (4.49) is assumed here based on the physics of the geometrically symmetrized effective stress concept (Cordebois and Sidoroff, 1979; Voyiadjis and Park, 1996a,b). Equation (4.41) may now be expressed as follows: −1 ¯ ij = a−1 ik ajl kl −1 = Mijkl

kl

(4.51)

Similiarly, equation (4.42) can be written as follows

ij = aik ajl ¯kl = Mijkl ¯kl

(4.52)

The relations combining the strain of the elastic damage deformation and the effective strain in equations (4.51) and (4.52) indicate that these relationships are equivalent to those obtained using the hypothesis of energy equivalence (Cordebois and Sidoroff 1982).


140

4.6

Damage Mechanics

Constitutive Behavior

Equation

of

Elastic-Damage

The constitutive equation of the elastic-damage behavior is obtained by simple mapping rather than using the energy equivalence hypothesis. The constitutive equation in the effective configuration is given by σ ¯ij = E¯ijkl ¯kl

(4.53)

¯ is the elastic stiffness tensor of the material in the absence of where E damage. Substituting equations (4.7) and (4.51) into equation (4.53) , the elastic-damage constitutive equation is obtained as follows: ¯klpq Nprqs rs σij = Nikjl E = Eijrs rs

(4.54)

The elastic damage stiffness is given as follows: ¯klpq Nprqs Eijrs = Nikjl E

(4.55)

where −1 Nikjl = Mikjl −1 = a−1 ik ajl

(4.56)

The elastic damage stiffness given by equation (4.55) is symmetric. This is in line with the classic (nonpolar) sense of continuum mechanics which is violated by using the hypothesis of strain equivalence. The damaged elastic stiffness is re-examined here using the fourth-order damage effective tensor M which is a function of the second-order damage tensor φ. The example of parallel cracks normal to the axis “1” is considered here. In this example the non-vanishing damage variables are the following φ11 = φˆ1

(4.57)

φ22 = φˆ2

(4.58)

φ33 = φˆ3

(4.59)

Since φˆ2 = φˆ3 φˆ1 one may assume for simplicity that φ22 = φ33 = 0. However, nonzeros for φˆ2 and φˆ3 are used here. The matrix form of the



141

damaged elastic stiffness E is as follows: ⎤ 0 0 0 ⎥ 0 0 0 ⎥ ⎥ 0 0 0 ⎥ ⎥ ¯1212 ⎥ 0 0 ψˆ1 ψˆ2 E 0 0 ⎥ ⎦ 0 0 0 ψˆ2 ψˆ3 E¯2323 0 ¯1313 0 0 0 0 ψˆ1 ψˆ3 E (4.60) ˆ ˆ where ψi = (1 − φi ). Alternatively, the matrix form of the damaged elastic compliance tensor S which is initially isotropic is given by

⎡ ¯1111 ψˆ1 ψˆ1 E ⎢ψˆ ψˆ E ⎢ 1 2 ¯1122 ⎢ˆ ˆ ¯ ⎢ψ ψ E [E] = ⎢ 1 3 1133 ⎢ 0 ⎢ ⎣ 0 0

¯1122 ψˆ1 ψˆ2 E ˆ ˆ ¯2222 ψ2 ψ2 E ¯2233 ψˆ2 ψˆ3 E

¯1133 ψˆ1 ψˆ3 E ˆ ˆ ¯2233 ψ2 ψ3 E ¯3333 ψˆ3 ψˆ3 E

⎡

1 −¯ ν −¯ ν ˆ1 ψ ˆ1 E ˆ1 ψ ˆ2 E ˆ1 ψ ˆ3 E ¯ ψ ¯ ψ ¯ ψ 1 −¯ ν ⎢ −¯ν ⎢ ψˆ1 ψˆ2 E¯ ψˆ2 ψˆ2 E¯ ψˆ2 ψˆ3 E¯ ⎢ −¯ν ν 1 ⎢ ψˆ ψˆ E¯ ψˆ −¯ ˆ ¯ ˆ ˆ ¯ 2 ψ3 E ψ3 ψ3 E ⎢ 1 3

[S] = ⎢ ⎢ ⎢ ⎣

0 0 0

0 0 0

0 0 0

0 0 0 1 ˆ1 ψ ˆ2 G ¯ ψ

0 0

0 0 0 0 1 ˆ2 ψ ˆ3 G ¯ ψ

0

0 0 0 0 0

⎤ ⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎦

(4.61)

1 ˆ1 ψ ˆ3 G ¯ ψ

¯ and G ¯ are the Poisson ratio, elastic and shear moduli, respecwhere ν¯, E, tively. Obviously, the damaged stiffness or compliance tensor shown is for transversely isotropic material. The damaged material is limited to orthotropic behavior using the second-order damage tensor φ. However, the damaged material exhibits general orthotropy when the principal damage directions are not coincident with the current coordinates. In this case, all components are not zero. More detailed examples of damaged compliance for micro-crack distribution using scalar, second-order, fourth-order, and sixth-order damage tensors are availble in the recent work by Krajcinovic and Mastilovic (1995).

4.7

Conclusion

The fourth-order anisotropic damage effect tensor, M, using the kinematic measure for damage expressed through the second-order damage tensor φ, is reviewed in this chapter in reference to the symmetrization of the effective stress tensor. This introduces a distinct kinematic measure of damage


142

Damage Mechanics

which is complementary to the deformation kinematic measure of strain. A thermodynamically consistent evolution equation for the damage tensor, φ together with a generalized thermodynamic force conjugate to the damage tensor is presented in the paper by Voyiadjis and Park (1995a,b). Voyiadjis and Venson (1995) quantified the physical values of the eigenvalues, φˆk (k = 1,2,3), and the second-order damage tensor, φ, for the unidirectional fibrous composite by measuring the crack densities with the assumption that one of the eigen-directions of the damage tensor coincides with the fiber direction. The fourth-order anisotropic damage effect tensor used here is obtained through the geometrical symmetrization of the effective stress (Cordebois and Sidoroff, 1979; Voyiadjis and Park, 1996a,b). This tensor is used here for the kinematic description of damage. The explicit representation of the fourth-order damage effect tensor is obtained with reference to the principal damage direction coordinate system. The elastic-damage deformation for finite strain is also described in this chapter using the kinematics of damage. The kinematics of elastic-damage behavior proposed here allows one to obtain the strain tensor of the elasticdamage deformation without the use of either the hypotheses of energy equivalence or strain equivalence. The proposed approach provides a relation between the effective strain and the damage elastic strain applicable to finite strains and is not confined to small strains as in the case of the strain equivalence or strain energy equivalence approaches. This leads to a simpler derivation of the elastic-damage constitutive equation for the elastic-damage behavior without the use of the hypothesis of energy equivalence.


5 Anisotropic Damage Mechanics

5.1

Introduction

Following the first pioneering paper of Kachanov (1958) on damage mechanics, many different types of damage models have been introduced such as ductile fracture (Sidoroff, 1981; Cordebois and Sidoroff, 1979; Cordebois, 1983; Lee, et al., 1985; Chow and Wang, 1987, 1988), fatigue of metals (Lemaitre, 1971; Chaboche, 1974), creep and creep-fatigue problems (Leckie and Hayhurst, 1974; Hult, 1974; Lemaitre and Chaboche, 1975), and other types of damage (Lemaitre, 1984). The concept of effective stress plays an important role in the definition of a suitable damage variable. The damage variable is usually defined to represent average material degradation that reflects all types of damage at the microscale level like nucleation and growth of voids, cavities, and other microcracks. The damage variable is assumed to be a second order tensor for the general case of anisotropic damage. The theory of anisotropic damage mechanics has been recently developed by Cordebois and Sidoroff (1979), Sidoroff (1981), Cordebois (1983), Chow and Wang (1987, 1988), Krajcinovic and Foneska (1981), Murakami and Ohno (1981), Murakami (1983), and Krajcinovic (1983), Voyiadjis and Kattan (1992,1999). The material in the following sections is based mainly on the work of Voyiadjis and Park (1996a,b). A computational anisotropic damage model is developed in this chapter. An updated Lagrangian finite element formulation is used for the numerical solution of the problem. In this model, finite strains are used; however, small elastic strains are assumed in the formulation. In Figure 5.1 (Chow and Wang, 1987), it is clear that the assumption of small elastic strains is valid for this material behavior. It is also shown how the computational model developed here can be applied to problems of ductile fracture. The classical problem of a center-cracked thin plate subjected to in-plane tensile forces is analyzed using the proposed model. The results obtained are compared with the experimental results of Chow and Wang (1988).


143

144

Damage Mechanics

FIGURE 5.1 Uniaxial stress-strain curves. (Voyiadjis and Park, 1996b)

5.2

Anisotropic Damage Criterion

The anisotropy of damage hardening is considered here in order to obtain a damage criterion for nonproportional loading. The damage criterion g is expressed in terms of a tensorial hardening parameter h and the generalized thermodynamic force Y conjugate to the damage tensor φ such that g ≡ pijkl Yij Ykl − 1 = 0

(5.1)

−1 pijkl = h−1 ij hkl

(5.2)

where

Equation (5.1) is an isotropic function of h and Y. The hardening tensor h is expressed as


Anisotropic Damage Mechanics

145

hij = (uik )1/2 φkl (uij )1/2 + Vij

(5.3)

D r1 ⎤ ⎡ λ1 q1 κλ1 0 0 ⎥ ⎢ D r2 ⎥ ⎢ [u] = ⎢ 0 λ2 q2 κλ2 0 ⎥ ⎣ D r3 ⎦ 0 0 λ3 q3 κλ3

(5.4)

⎡ ⎤ λ1 v12 0 0 [V] = ⎣ 0 λ2 v22 0 ⎦ 0 0 λ3 v32

(5.5)

Tensors u and V are generalizations to orthotropic materials of the scalar forms of isotropic materials originally proposed by Stumvoll and Swoboda (1993). The quantities λ1 , λ2 , λ3 , v1 , v2 , v3 , r1 , r2 , r3 , q1 , q2 and q3 are material parameters obtained by matching the theory with experimental results. Parameters λ1 , λ2 and λ3 are related to the elasticity tensor E, for an orthotropic material expressed by the 6 × 6 matrix ⎡ ⎤ λ1 λ3 0 0 0 (λ1 + 2µ1 ) ⎢ λ1 (λ2 + 2µ2 ) λ2 0 0 0⎥ ⎢ ⎥ ⎢ ⎥ λ λ (λ + 2µ ) 3 2 3 3 0 0 0 ⎥ ⎢ [E] = ⎢ (5.6) ⎥ 0 0 0 0 0 µ 1 ⎢ ⎥ ⎣ 0 0 0 0 µ2 0 ⎦ 0 0 0 0 0 µ3 such that

E1122 1 (E1111 − E1122 ) 2 E2233 1 (E2222 − E2233 ) 2 E1133 1 (E3333 − E1133 ) 2

= λ1 = µ1 = λ2 = µ2 = λ3 = µ2

(5.7)

The parameters v1 , v2 and v3 in equation (5.5) define the initial threshold against damage for the orthotropic material. These parameters are obtained from the constraint that the onset of damage corresponds to the stress level at which the virgin material starts exhibiting nonlinearity. The scalar damage hardening parameter κD in equation (5.4) is given by


146

Damage Mechanics κ

D

t

−Yij φ˙ ij dt

=

(5.8)

0

The damaging state is defined as any state that satisfies g = 0. Four different states are outlined below: g < 0,

(elastic − unloading)

(5.9a)

∂g ˙ Yij < 0 g = 0, ∂ Y˙ ij

(elastic − unloading)

(5.9b)

(neutral loading)

(5.9c)

(loading f or a damaging state)

(5.9d)

∂g ˙ Yij = 0 ∂ Y˙ ij ∂g ˙ Yij > 0 g = 0, ∂ Y˙ ij g = 0,

An anisotropic damage criterion g is proposed here by expression (5.1). The corresponding loading conditions are given by equations (5.9). The damage criterion is expressed through the second order tensors u and V and the damage tensor φ.

5.3

Damage Tensor

In this section, the effective stress concept proposed by Kachanov (1958) and later generalized by Murakami (1988) is used. The initial undeformed and undamaged configuration of the body will be referred to as C0 while C¯ refers to the state of the body after it has only deformed without damage. The configuration of the body that is both deformed and damaged after a set of external agencies act on it is referred to as C (Voyiadjis and Kattan, 1992, 1999). A linear transformation is assumed between the Cauchy stress ¯ such that: tensor σ, and the effective Cauchy stress tensor σ σ ¯ij = Mijkl σkl

(5.10)

where M is the fourth-order damage effect tensor. Murakami (1988) has shown that M can be represented by 6 × 6 matrix as a function of (I2 − φ) such that [M] = [M(I2 − φ)]

(5.11)

where φ is a symmetric second order tensor and I2 is the second-rank identity tensor. The effective Cauchy stress need not be symmetric or



147

frame invariant under the given transformation. However, once the effective Cauchy stress is symmetrized, it can be shown that it satisfies the frame invariance principle (Voyiadjis and Kattan, 1992, 1999). The stress tensor M in conjunction with the matrix form of M may be represented in vector form as shown: T

[σ] = [σ11 , σ22 , σ33 , σ12 , σ23 , σ31 ]

(5.12)

¯ used here is given by (Lee, et al., 1986) The symmetrized σ 1 [σik (δkj − φki )−1 + (δil − φil )−1 σlj ] (5.13) 2 ¯ is frame independent. Making use of the symmetrization This stress, σ, procedure given by equation (5.13), the (6 × 6) matrix form of tensor M is given by Voyiadjis and Kattan (1992, 1999) as follows: σ ¯ij =

⎡

0 0 2ω22 ω33 − 2φ223 2 ⎢ 0 2ω ω − 2φ 0 11 33 13 ⎢ 2 1 ⎢ 0 0 2ω ω 11 22 − 2φ12 ⎢ [M] = 0 2 ⎢ ⎢ φ13 φ23 + φ12 ω33 φ13 φ23 + φ12 ω33 ⎣ 0 φ12 φ13 + φ23 ω11 φ12 φ13 + φ23 ω11 φ12 φ23 + φ13 ω22 0 φ12 φ23 + φ13 ω22 2φ13 φ23 + 2φ12 ω33 0 2φ13 φ23 + 2φ12 ω33 2φ12 φ13 + 2φ23 ω11 0 2φ12 φ13 + 2φ23 ω11 ω22 ω33 + ω11 ω33 − φ223 − φ213 φ12 φ23 + φ13 ω22 φ12 φ23 + φ13 ω22 ω11 ω33 + ω11 ω22 − φ213 − φ212 φ12 φ13 + φ23 ω11 φ13 φ23 + φ12 ω33 ⎤ 2φ12 φ23 + 2φ13 ω22 ⎥ 0 ⎥ ⎥ 2φ12 φ23 + 2φ13 ω22 ⎥ ⎥ φ12 φ13 + φ23 ω11 ⎥ ⎦ φ13 φ23 + φ12 ω33 ω22 ω33 + ω11 ω22 − φ223 − φ212

(5.14)

where is given by

= ω11 ω22 ω33 − φ223 ω11 − φ213 ω22 − φ212 ω33 − 2φ12 φ23 φ13

(5.15)

The notation ωij is used to denote δij − φij . Using the principal damage values φ1 , φ2 , φ3 , then Equation (5.14) may be expressed as follows:


148

Damage Mechanics

⎡ ⎢ ⎢ ⎢ ⎢ [M]diag. ⎢ ⎢ ⎢ ⎢ ⎣

1 1−φ1

0

0 0

0 0 0

0 0 0 0

0 0 0

1 1−φ2

0 0

1 1−φ3

0

(1−φ2 )+(1−φ1 ) 2(1−φ2 )(1−φ1 )

0

0

0

0

(1−φ3 )+(1−φ2 ) 2(1−φ3 )(1−φ2 )

0

0

0

0

0

⎤

0 0 0 0 0 (1−φ3 )+(1−φ1 ) 2(1−φ3 )(1−φ1 )

⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎥ ⎦

(5.16) However, in this chapter, the matrix representation of M for the case of plane stress will be used. For the case of a thin plate subjected to a state of plane stress, it is assumed that the plate lies in the 1-2 plane under plane stress conditions. For plane stress, Equation (5.14) reduces to the following expression (Voyiadjis and Kattan, 1992, 1999) ⎧ ⎫ ⎡ ⎤⎧ ⎫ ¯11 ⎬ M11 M12 M13 ⎨σ11 ⎬ ⎨σ σ ¯22 = ⎣M21 M22 M23 ⎦ σ22 ⎩ ⎭ ⎩ ⎭ σ ¯12 M31 M32 M33 σ12

(5.17)

where M11 = M22 = M33 = M12 = M13 = M23 =

(1 − φ22 ) ∆ (1 − φ11 ) ∆ (M11 + M22 ) 2 M21 = 0 φ12 2M31 = ∆ 2M32 = M13

∆ = (1 − φ11 )(1 − φ22 ) − φ212

(5.18a) (5.18b) (5.18c) (5.18d) (5.18e) (5.18f) (5.18g)

The stresses and damage variables for the plane stress case are represented by 3 × 1 vectors such that

{σ} = [σ11 , σ22 , σ12 ]T {φ} = [φ11 , φ22 , φ12 ]T


(5.19a) (5.19b)


5.4

149

Damage Evolution

Although the two dissipative mechanisms of plasticity and damage influence each other, in this section, it is assumed that the energy dissipated due to plasticity and that due to damage are independent of each other. The power of dissipation Π is given by Π = ΠD + ΠP

(5.20)

where ΠP is the plastic dissipation and ΠD the corresponding damage dissipation. The plastic dissipation is given by ΠP = σij ˙ij + αij β˙ ij + K P κ˙ P

(5.21)

In this chapter, small elastic strains but finite inelastic deformations are assumed and the strain rate is assumed to be decomposed into an elastic component, ˙ij and a plastic component, ˙ij , such that

ij = ij + ij

(5.22)

From the experimental results shown in Figure 5.1 by Chow and Wang (1987), it is clearly indicated there that the elastic strains are extremely small (less than 0.2%) and therefore justifiably assumed to be small. In equation (5.21), the term αij β˙ ij is associated with kinematic hardening and K P κ˙ P with plastic isotropic hardening. The associated damage dissipation is given by ΠD = Yij φ˙ ij + K D κ˙ D

(5.23)

The fictitious undamaged material is characterized by the effective stress ¯ the body has and effective strain. Since in the effective configuration, C, deformed without damage, hence the dissipation energy of the fictitious undamaged material is only composed of the plastic dissipation. ¯ =Π ¯P Π

(5.24)

P ¯ =σ ¯Pκ Π ¯ij ¯ ˙ij + α ¯ij β¯˙ ij + K ¯˙

(5.25)

and

Since it is assumed that plastic yielding is independent of the damage process, consequently the plastic dissipation in the damaged material is equal to the corresponding plastic dissipation in the fictitious undamaged material. This leads to the following expression


150

Damage Mechanics ¯P ΠP = Π

(5.26)

The following decomposition is further assumed:

¯ij ¯˙ij σij ˙ij = σ α β˙ = α ¯ β¯˙ ij ij

P

P

ij

¯P

ij P

K κ˙ = K κ ¯˙

(5.27a) (5.27b) (5.27c)

The assumptions imposed in order to obtain equation (5.27) from equation (5.26) is an attempt to simplify the problem in order to obtain a closed form expression for the stiffness matrix. Without these assumptions, the problem may not be solved. However, the good correlation between the experimental and numerical results provide a justification for this assumption. Making use of equations (5.27a) and (5.10) one obtains a transformation equation for the plastic strain rates such that −1

˙kl

¯˙ij = Mijkl

(5.28)

Using the method of the calculus of functions of several variables, one introduces two Lagrange multipliers Λ˙ 1 and Λ˙ 2 and forms the function Ω such that (Voyiadjis and Kattan, 1992, 1999) Ω = Π − Λ˙ 1 f − Λ˙ 2 g

(5.29)

where f (σ, α) is the plastic yield function and α is the backstress tensor. To extremize the function Ω, one uses the necessary conditions ∂Ω =0 ∂σij

(5.30a)

∂Ω =0 ∂Yij

(5.30b)

and

which give the corresponding plastic strain rate and damage rate evolution equations, respectively: ∂f

˙ij = Λ˙ 1 ∂σij

(5.31)

∂g φ˙ ij = Λ˙ 2 ∂Yij

(5.32)

and



151

Equation (5.32) gives the increment of damage from the potential g. Using the consistency condition for damage, g˙ = 0

(5.33)

which states that after an increment of damage the volume element again must be in a damaging state, the quantity Λ˙ 2 is obtained such that Λ˙ 2 = −

∂g ∂Ymn ∂g ∂g ∂φij ∂Yij

Y˙ mn

(5.34)

Substituting equation (5.34) into equation (5.32), one obtains φ˙ kl = Ψklij Y˙ ij

(5.35)

where the fourth order tensor Ψ is given by Ψklij = −

∂g ∂g ∂Ykl ∂Yij ∂g ∂g ∂φmn ∂Ymn

(5.36)

The generalized thermodynamic force Y, is assumed to be a function of the elastic component of the strain tensor , and the damage tensor φ, or the stress σ and φ Y = Y( , φ)

or

Y = Y(σ, φ)

(5.37)

The evolution equation for Y may be expressed as follows: ∂Yij ∂Yij ˙ Y˙ ij = σ˙ mn + φpq ∂σmn ∂φpq

(5.38)

˙ from equation (5.38) into equation (5.35) one obtains Substituting for Y ∂Yij ∂Yij ˙ φ˙ kl = Ψklij σ˙ mn + φpq (5.39) ∂σmn ∂φpq Equation (5.39) may be further reduced to Lijkl φ˙ kl = Ψijrs

∂Yrs σ˙ mn ∂σmn

(5.40)

where Lijkl =

∂Ymn 1 (δik δjl + δil δjk ) − Ψijmn 2 ∂φkl

Equation (5.40) is used to solve for φ˙ such that


(5.41)

152

Damage Mechanics

φ˙ kl =

∂Yrs −1 Lijkl Ψijrs σ˙ mn ∂σmn

(5.42a)

φ˙ kl = Tklmn σ˙ mn

(5.42b)

or

The thermodynamic force associated with damage is obtained using the enthalpy of the damaged material where V (σ, φ) = σmn mn − W

(5.43)

or 1 −1 σmn Emnkl (φ)σkl (5.44) 2 and W is the specific energy. In equation (5.44), E is the damaged elasticity tensor. The thermodynamic force is given by V =

Yij = −

∂V ∂φij

(5.45a)

or Yij =

−∂V ∂Mabcd ∂Mabcd ∂φij

(5.45b)

Using the energy equivalence principle, one obtains a relation between the damaged elasticity tensor E and the effective, undamaged, elasticity tensor ¯ such that (Voyiadjis and Kattan, 1992, 1999) E −1 −1 (φ) = Muvmn (φ)E¯uvpq Mpqkl (φ) Emnkl

(5.46)

Making use of equations (5.44) and (5.45), the thermodynamic force is given explicitly as follows:

Yij =

5.5

−1 ¯ −1 Mpqkl σkl + σkl Mpqkl E ¯ −1 σcd ) ∂Mabcd (σcd E abpq pqab 2 ∂σij

(5.47)

Constitutive Model

In this section, the elasto-plastic stiffness matrix that involves damage effects is derived. Rate-dependent effects are neglected and isothermal conditions are assumed.



153

The incremental form of equation (5.10) may be expressed as σ ¯˙ ij = M˙ ijkl σkl + Mijkl σ˙ kl

(5.48)

Making use of the additive decomposition of the effective strain rate and equation (5.28), one obtains −1 −1

kl + Mijkl

˙kl

¯˙ij = M˙ ijkl

(5.49)

The rates of the damage effect tensor and its inverse may be expressed as follows by making use of equation (5.42b) ∂Mijkl M˙ ijkl = Tpqmn σ˙ mn ∂φpq = Qijklmn σ˙ mn

(5.50a) (5.50b)

and

−1 = M˙ ijkl

−1 ∂Mijkl

Tpqmn σ˙ mn ∂φpq = Rijklmn σ˙ mn

(5.51a) (5.51b)

In order to obtain the elasto-plastic stiffness matrix that involves damage effects, we start with the elasto-plastic stiffness relation in the undamaged configuration given by Voyiadjis and Kattan (1992, 1999) ¯ ijkl ¯˙kl (5.52) σ ¯˙ ij = D ¯ is given by Voyiadjis and Kattan The elasto-plastic effective stiffness D (1992, 1999). ¯ ¯ ¯ klmn = E ¯pqmn E¯klij ∂ f ¯klmn − 1 ∂ f E D Q ∂σ ¯pq ∂σ ¯ij

(5.53) ¯

¯

∂f ∂f ∂ f¯ ∂ f¯ ∂ f¯ ¯ ∂ f¯ ∂ f¯ ∂σ ¯ ij ∂ σ ¯ ij ¯ Eabcd Q= − σ ¯pq − (¯ σef − α ¯ef )b ∂σab ∂σ ¯cd ∂κp ∂σ ¯pq ∂σ ¯ef (¯ σgh − α ¯ gh )

∂ f¯ ∂σ ¯ gh

(5.54) This is valid for a yield function of the form 3 (¯ σkl − α ¯kl )(¯ σkl − α ¯ kl ) − σ ¯02 − c¯ κP = 0 (5.55) 2 The plastic work κ ¯ P is a scalar function and its evolution in the configuration C¯ is taken to be in the form f=


154

Damage Mechanics P κ ¯˙ = ( ¯˙ij ¯ ˙ij )1/2

(5.56)

A Prager-Ziegler kinematic hardening evolution law is used such that ¯˙ (¯ σij − α ¯ ij ) α ¯˙ ij = µ

(5.57)

Making use of equations (5.52), (5.49), (5.50b) and (5.51b), one obtains the resulting elastoplastic stiffness relation in the damaged configuration as follows: σ˙ mn = Dmnpq ˙pq

(5.58)

−1 ¯ ijkl M −1 Dmnpq = Omnij D klpq

(5.59)

where

and ¯ ijmn Rmnpqkl E −1 σab Oijkl = Qijmnkl σmn + Mijkl − D pqab

(5.60)

It is interesting to note that for the case of no damage, tensors Q and R reduce to zero and M becomes a fourth order identity tensor. In this case, equation (5.58) reduces to equation (5.52).

5.6

Uniaxial Tension Analysis

In order to obtain the damage parameters, uniaxial tension analysis for the aluminum alloy 2024-T3 is simulated numerically and compared with experimental results (Chow and Wang, 1987, 1988). The damage parameters ql , q2 , q3 , rl , r2 and r3 are selected such that the computed results present a best fit of the experimental data. The stress-strain curves shown in Figure 5.1 show good agreement with the experimental data by Chow and Wang (1987). In addition to the stress-strain curve, damage evolutions with respect to the stress and strain are shown in Figure 5.2 and 5.3, respectively. It is clearly shown that the growth of damage with stress accelerates rapidly near failure. This is in accord with the experiments of Chow and Wang (1987, 1988) whereby a substantial increase in the crack density is instrumental in forming links between the cracks that leads to failure.



5.7

155

Finite Element Implementation

The model is implemented numerically using an updated Lagrangian finite element method. The basic assumptions and equations for the finite element formulations have been presented by Kattan and Voyiadjis (1990) and Voyiadjis and Kattan (1990). The final incremental equilibrium equations in the updated Lagrangian description are given by (Kattan and Voyiadjis, 1990)

FIGURE 5.2 Uniaxial stress-damage curves. (Voyiadjis and Park, 1996b)


156

Damage Mechanics ([K] + [K]σ + [K](N C) ){dv} = {dP }

(5.61)

where {dv} is the unknown incremental vector for the nodal displacements and {dP } is the corresponding incremental vector for the nodal forces. [K] is the symmetric “large displacement” matrix, [K]σ is the symmetric “initial stress” matrix, and [K](N C) is the nonsymmetric “displacement dependent load” matrix. These matrices are given by ∂Nkb ∂Nia Kab = Dijkl dV (5.62a) ∂xj ∂xl

FIGURE 5.3 Uniaxial strain-damage curves. (Voyiadjis and Park, 1996b)


Anisotropic Damage Mechanics ∂Nkb ∂Nka (σ) Kab = σij dV ∂xi ∂xj and

(N C) Kab

=

∂pi Njb Nia dV + ∂xj

157 (5.62b)

Tib Nia dA

(5.62c)

where Nij are the shape functions, Tib are defined by the following relation (Zienkiewicz, 1977). ∂ti uj = Tib qb ∂xj

(5.63)

and qb are the incremental nodal displacements. The above equations are applicable to the model presented provided the appropriate elasto-plastic, damage stiffness matrix D is substituted. The incremental vector for the nodal forces is given as follows: dPα = (dpi )Nia dV + (dti )Nia dA (5.64) The damage model used in this work is successfully implemented in the fmite element program DNA (Damage Nonlinear Analysis). A convergence criteria is used to terminate the equilibrium iteration at each load increment. At the end of each iteration, the solution obtained is checked using (i) the internal energy criterion ∆Wn as follows: {∆u}(i)T (m+1 {R} −m+1 {F }(i) ) ≤ E {∆u}(i)T (m+1 {R} −m {F }) (5.65) where {∆u}(i) is the displacement increment obtained in the ith iteration, T is used to denote the transpose of a vector, and m {R} and m {F } are the internal force and external force vectors in the mth increment, respectively. The left-hand side of the inequality represents the work done by the outof-balance force on the displacement increment, and the right-hand side is the initial value of the same work. In equation (5.63), E is a prescribed tolerance for internal energy.

5.8

Center-Cracked Tensile Forces

Thin

Plate

Under

In-Plane

The proposed model is primarily derived to solve problems in ductile fracture. As an example, the problem of crack initiation in a center-cracked


158

Damage Mechanics TABLE 5.1

Material properties and parameters (aluminum alloy 2024-T3). Modulus Poisson’s ration Yielding stress Kinematic hardening parameter Isotropic hardening parameter Damage parameters

73, 087 MPa 0.3 330 MPa b = 275.8 MPa c = 792.9 MPa r1 = r2 = r3 = 0.64 q1 = q2 = q3 = 0.53 v1 = v2 = v3 = 0.006

thin plate, shown in Figure 5.4, that is subjected to in-plane tension is analyzed. The material used is aluminum alloy 2024 T3. All material properties and parameters are shown in Table 5.1. Since the thickness of the plate (t = 3.175 mm) is small compared with the other dimension, a state of plane stress is assumed. Due to symmetry in geometry and loading, only one-quarter of the plate is discretized by finite elements as shown in Figure 5.5. The eight-node quadrilateral isoparametric element is used in this finite element analysis. It is noticed that a large number of regular elements are used around the crack tip in order to avoid the special (singularity) elements at that point (Henshell and Shaw, 1975; Barsoum, 1976). Consequently, a total of 381 elements and 1228 nodes are used. The load is incremented with uniform load increments of 5 MPa until the principal damage value φp reaches 1.0 (φp ≤ 1.0). The principal damage variable φp is given by: φxx + φyy φp = + 2

φxx + φyy 2

2 + φ2xy

(5.66)

Consequently, material failure, φc , occurs when φc = 0.38, that is φp = 0.38. The principal damage value is monitored at each load increment since it is used to determine the onset of macro-crack initiation. The onset of macro-crack initiation occurs at the front of crack tip when the final load of 265 MPa is reached. This is compared with the crack initiation load of 263.6 MPa obtained from experiments done by Chow and Wang (1988). The contours of stresses σxx , σyy and σxy , for the quarter plate and around the crack tip for the load 260 MPa are shown in Figures 5.6 and 5.7, respectively. It is clear from Figure 5.6 and 5.7 that high stresses are localized around the crack tip with a maximum σyy = 622 MPa.



159

FIGURE 5.4 (a) This plate with a center crack. (b) Quarter of plate to be discretized by finite elements.(Voyiadjis and Park, 1996b)

Figure 5.8 shows the contours for the damage variables φxx , φyy and φxy . The maximum damage value of 0.28 (φyy ) occurs near the tip of the crack. All the damage values stabilize when the crack initiation load of 260 MPa is reached. Once this load is attained, damage increases without further


160

FIGURE 5.5 Finite element mesh. (Voyiadjis and Park, 1996b)

increase in load, thus initiating macrocracks.


Damage Mechanics


161

FIGURE 5.6 Contour lines for stresses for the quarter plate at a load of P = 260 MPa (a) Stress σxx contours in MPa. (b) Stress σyy contours in MPa. (c) Stress σxy contours in MPa. (Voyiadjis and Park, 1996b)


162

Damage Mechanics

(a)

(b)



163

(c)

FIGURE 5.7 Contour lines for the stresses around the crack at a load of P = 260MPa: (a) stress σxx contours in MPa, (b) stress σyy contours in MPa, (c) stress σxy contours in MPa. (Voyiadjis and Park, 1996b)


164

Damage Mechanics

(a)

(b)



165

(c)

FIGURE 5.8 Contour lines for the stresses around the crack at a load of P = 260MPa: (a) stress σxx contours in MPa, (b) stress σyy contours in MPa, (c) stress σxy contours in MPa. (Voyiadjis and Park, 1996b)


166

5.9

Damage Mechanics

Conclusion

An anisotropic damage model is proposed for the characterization of the degradation of the material properties as well as for the onset of macrocrack initiation in metals. The evolution and growth of damage using the proposed theory compares well with the experimental data from the uniaxial tension test given by Chow and Wang (1987). The authors have attempted to provide an anisotropic damage model in order to accurately predict the behavior of the material. The use of this versatile and general anisotropic model imposes six parameters for which the authors have not obtained direct physical correlation. However, some other parameters in the formulation have direct physical correlation such as λ1 , λ2 , λ3 , v1 , v2 and v3 . Finite element implementation of a damage-plasticity model is formulated to analyze a center-cracked thin elasto-plastic plate subjected to inplane tensile forces. The model uses the coupling of finite strain plasticity and damage mechanics incorporating both isotropic and kinematic hardening. The results for the stresses, strains and damage variables are shown and compared for the proposed model. It is shown that the damage variables increase monotonically with the applied load. The critical values for the damage variables needed to initiate macrocracks are within the range 0.2 to 0.8. This is in agreement with the work of Lemaitre (1984, 1986).


6 Plasticity Theory

The nonlinear behavior of metals when subjected to monotonic, and cyclic non-proportional loading is modeled using the proposed hardening rule. The plasticity model is based on the Chaboche (1989, 1991) and Voyiadjis and Sivakumar (1991, 1994) models incorporating the bounding surface concept. The evolution of the backstress is governed by the deviatoric stress rate direction, the plastic strain rate, the backstress, and the proximity of the yield surface from the bounding surface. In order to ensure uniqueness of the solution, nesting of the yield surface with the bounding surface is ensured. The prediction of the model in uniaxial cyclic loading is compared with the experimental results obtained by Chaboche (1989, 1991). The behavior of the model in multiaxial stress space is tested by comparing it with the experimental results in axial and torsional loadings performed by Shiratori, et al. (1979) for different stress trajectories. The amount of hardening of the material is tested for different complex stress paths. The model gives a very satisfactory result under uniaxial, cyclic and biaxial non-proportional loadings. Ratchetting is also illustrated using a non-proportional loading history.

6.1

Introduction

Voyiadjis and Sivakumar (1991, 1994) proposed a robust kinematic hardening model that ensures the nesting of the yield and bounding surfaces. This is accomplished by defining a kinematic hardening rule that blends the deviatoric stress rate rule for the movement of the yield surface with that of the Tseng and Lee rule (1983). This approach satisfies both the experimental observations made by Phillips, et al. (1974), and the nesting of the yield surface with the bounding surface. A general expression for the plastic modulus is also proposed in this chapter. The expressions proposed by McDowell (1987) and Dafalias (1981) may be obtained as a special case of that proposed by Voyiadjis and Sivakumar (1991, 1994). An additional parameter is also introduced in this work that reflects the dependence of


167

168

Damage Mechanics

the plastic modulus on the angle between the deviatoric stress rate tensor and the tensor joining the center of the bounding surface and the yield surface. The movement of the center of the yield surface is along a curved path in this case and not along a straight line path as predicted by Tseng and Lee (1983). The Voyiadjis and Sivakumar model (1994) predicts the yielding and ratchetting behavior of the material under cyclic loading quite well as compared with the experimental results of Shiratori, et al. (1979). However, the effective plastic strains are overpredicted at low values of the plastic strains. The objective of this chapter is to develop a constitutive model that can describe the plastic response of class M materials under complex loading conditions specifically for hardening effects. An attempt is made to formulate a new kinematic hardening rule that can predict the response of the material under both monotonic and cyclic loadings. The model is based on both the Chaboche model (1989, 1991) and the Voyiadjis-Sivakumar model (1991, 1994). A new term involving the stress rate is incorporated in the evolution equation of the backstress along with a coefficient that depends on the proximity of the yield surface from the bounding surface. The prediction of the model in uniaxial monotonic and cyclic loading is compared with the experimental results obtained by Chaboche (1989, 1991). The behavior of the model in multiaxial stress space is tested by comparing it with the experimental results in axial and torsional loadings performed by Shiratori, et al. (1979) for different stress trajectories.

6.2

Theoretical Formulation

The model is developed in the multidimensional stress space. The yield surface is of a von Mises type given as follows: f≡

3 (s : s) − k 2 = 0 2

(6.1)

where s=τ −X

(6.2)

The yield surface is expressed in terms of deviatoric components, τ , of the Cauchy stress tensor, σ, and the backstress tensor X. The tensorial operation “:” on second order tensors implies the the following: s : s = sij sij


(6.3)

Plasticity Theory

169

In equation (6.1), k is the radius of the yield surface. The initial size of the yield surface is given by k0 , defining the initial yield strength of the material in the uniaxial tension test. It should be noted that for class M materials, the hydrostatic component of the stress tensor is assumed to have no effect on the plastic deformation. An additive decomposition of the strain rate tensor, ˙ , is assumed such that ˙ = ˙ + ˙

(6.4)

where ˙ is the elastic component of the strain rate tensor, and ˙ the corresponding plastic strain rate component. An associative flow rule is assumed in this formulation such that ˙ = Λ˙

∂f ∂σ

(6.5)

where Λ˙ is a Lagrangian multiplier in conjunction with the flow rule. Armstrong and Frederick (1966) proposed a kinematic hardening rule in ˙ is given as follows: which the evolution equation for the backstress, X, ˙ = 2 C ˙ − γXp˙ X (6.6) 3 where C and γ are constants and p is the accumulated plastic strain rate, 2 p˙ = ˙ ˙ (6.7) 3 ij ij Chaboche (1989, 1991) proposed a model based on Armstrong and Frederick (1966) in which the evolution equation of the backstress is decomposed into several components. The backstress is calculated as the sum of X(i) components such that X=

N

X(i)

(6.8)

i=1

where ˙ (i) = 2 C (i) ˙ − γ (i) X(i) p˙ X 3

(6.9)

and the summation in equation (6.8) varies depending on the model type. Chaboche (1989, 1991) proposed different models, namely, the short range kinematic model (NLK), the long rate kinematic model with Prager linearkinematic rule (LK), the non-linear Prager rule (NLP2), the model with a modified recall term with a power function called MILL, and the model with a modified recall term with a threshold. (NLK-T). Each model has


170

Damage Mechanics

different values for the constants C (i) and γ (i) . Chaboche (1991) showed that the NLK-T model best predicts the experimental results. This model introduces a nonlinearity in the recall term through a threshold term X . The model is used to simulate the experiments performed on type 316 stainless steel. The model gives good correlation with experimental results for uniaxial monotonic, normal cyclic, and ratchetting conditions. However, when a small cycle is incorporated during a transient in a large cycle, the small cycle loop does not close the loop as it is anticipated from experimental observations. The closure of the small loop is not completed. The modeling of such behavior needs a discrete memory scheme to reproduce the above result. Isotropic hardening is also incorporated in the proposed model. The isotropic hardening rule was proposed initially by Chaboche (1989) and generalized by Ohno (1982). The model introduces a surface of nonhardening in the plastic strain space. Ohno and Wang (1991, 1993) showed in their work that the formulation as given by Chaboche (1989) can be shown to be a multi-surface model. They show that the multi-surfaces generated are nested and obey an Mroz-type (1967, 1969) translation rule. They also show that for each X there exists a bounding surface in the X space ˙ depends on the radius of its bounding surface, its proximity from and X the bounding surface, and the plastic strain rate ˙ . The yield surface moves with the bounding surfaces with all the surfaces nesting each other at the point of loading with the center of each surface lying on a straight line. However, a general single bounding surface for all the components of X is not used which allows more flexibility and simplicity in accurately predicting any combination of monotonic and cyclic loads. In the present chapter, a new term is added to the Armstrong-Frederick (1966) kinematic hardening rule to allow for the motion of the yield surface to be influenced by the direction of the stress rate as indicated by Phillips, et al. (1974). The kinematic hardening rule as given by Voyiadjis and Basuroychowdhury (1998) is as follows: ˙ (i) p˙ + lδ β (i) ˙ (i) = 2 C (i) ˙ − γ (i) X X 3 m

(6.10a)

and ˙ = X

4

˙ (i) X

(6.10b)

i=1

where β (i) is a material parameter and l is the direction of the stress rate. In equation (6.10a), m is the length of the chord of the bounding surface along the direction of loading as indicated in Figure 6.1. The proximity of the yield surface from the bounding surface is given by δ which is the


Plasticity Theory

171

X X

X

FIGURE 6.1 Proposed two surface kinematic hardening model.(Voyiadjis and Basuroychowdury, 1998)

distance of the stress point from the bounding surface in the direction of the stress rate tensor. Referring to Figure 6.1, δ and m are derived as follows: τ − B =

(τ − B) : (τ − B)

(6.11)

The measure of the projection of τ − B along the direction of the stress rate is given by the following expression (τ − B) : l = (τij − Bij )lij


(6.12)

172

Damage Mechanics

where B is the backstress tensor defining the center of the bounding surface. The lengths m and δ are given by the following expressions: m=2

K 2 − ( τ − B )2 + [(τ − B) : l]2

(6.13)

m − (τ − B) : l (6.14) 2 Equations (6.13) and (6.14) are valid until any point on the yield surface touches the bounding surface. The constraint for such a condition may be given by the following expression: δ=

X − B +k ≤ K

(6.15)

where K is the radius of the bounding surface. Referring to Figure 6.1, the motion of yield surface is adjusted so that it does not intersect the bounding surface on contact. Equations (6.10) are valid for the movement of the yield surface until the surface touches the bounding surface. As soon as any point on the yield surface comes in contact with the bounding surface, the yield surface is rotated in order to allow the loading point on the yield surface to touch the bounding surface without allowing the yield surface to intersect the bounding surface. Thereafter, the movement of the center of the yield surface is governed by the movement of the bounding surface until the two surfaces separate from each other. Once the yield surface touches the bounding surface, the yield surface is rotated in such a way that the loading point on the yield surface comes in contact with the bounding surface. The yield surface then moves with the bounding surface and, consequently, the movement of the yield surface is constrained by the movement of the bounding surface. The movement of the center of the yield surface during the process of rotation of the yield surface until the loading point on the yield surface comes in contact with the bounding surface is shown in Figure 6.2. Referring to Figure 6.2, p is a unit tensor along the direction of the backstress when the point of loading on the yield surface touches the bounding surface. XN is the location of the center of the yield surface at contact with the bounding surface when the point of loading is on the bounding surface. XP is the location of the center of the yield surface when initial contact with the bounding surface has occurred but the point of loading is not on the bounding surface. In Figure 6.2, L is the distance AB, and γ is the angle between the stress tensor (τ − B) and the direction of the stress rate l. These tensors and parameters are defined by the following relations:


Plasticity Theory

173

X X

FIGURE 6.2 When yield surface touches the bounding surface.(Voyiadjis and Basuroychowdury, 1998)

cos γ =

L = (τ − B) cos γ +

l : (τ − B) l : (τ − B)

(6.16)

( τ − B cos γ)2 − (( τ − B )2 − K 2 ) (6.17)


174

Damage Mechanics K 2 = ( τ − B )2 + L2 − 2 τ − B L cos γ p=

(τ − B) + Ll K

XN = (K − k)p − B

(6.18) (6.19) (6.20)

Finally, the evolution expression for X is now given as ˙ = XN − Xp X

(6.21a)

˙ = (K − k)p − (B + Xp ) X

(6.21b)

The above derivations are used to define the movement of the yield surface and the elasto-plastic stiffness tensor is developed accordingly. The above formulations are easy to compute numerically and, accordingly, a computer program is developed to find the backstress, and thereafter calculating the strains. A computer program is developed to take into account the elasto-plastic stiffness tensor for incremental loading, and the total and plastic strains are calculated for different values of σ. The elasto-plastic stiffness fourth-order tensor may be derived using the consistency condition such that ∂f ∂f (1 − β) :E (6.22) E: ⊗ D=E− A ∂σ ∂σ where ∂f ∂f ∂f ∂f 2 ∂f 2 ∂f ∂f :E: : : A= (1 − β) − C + γX : ∂σ ∂σ 3 ∂σ ∂σ ∂σ 3 ∂σ ∂σ (6.23) and E is the fourth order elastic stiffness tensor. In the above expressions, tensor multiplications of fourth-order tensors with second-order tensors using the symbol “:” implies

E:

∂f ∂f = Eijkl ∂σ ∂σkl

(6.24)

Tensor operations on second-order tensors using the symbol ⊗ imply a ⊗ b = aij bkl In equation (6.23), the terms C and γX are given as follows:


(6.25)

Plasticity Theory

175

C=

4

C (i) ,

i=4

β=

4

β (i)

(6.26)

i=1

and γX =

4

γ (i) X(i)

(6.27)

i=1

The Lagrangian multiplier Λ˙ in conjunction with the plastic strain rate tensor given by equation (6.5) is given as follows: ˙Λ = 1 ∂f : E : ˙ (1 − β) (6.28) A ∂σ Isotropic hardening of the type proposed by Chaboche (1989, 1991) in the NLK-T model is used in this chapter. This isotropic hardening rule was initially proposed by Chaboche and generalized by Ohno (1982). The model introduces a surface of nonhardening in the plastic strain space. In the equation for the yield surface, the material constant k is replaced by k + R. R is a variable which is zero at the initiation of yielding. The evolution of R is given as follows: R˙ = b[Q(q) − R]p˙

(6.29)

Q = QM + (QO + QM )e−2µq

(6.30)

where

QO , QM , µ and b are material constants. The available q stores one-half the plastic strain amplitude in each cycle ∆ /2 , which in turn depends on the total strain amplitude to which the material is subjected in cyclic loading.

6.3

Monotonic and Cyclic Tension Loadings on 316 Stainless Steel

The proposed model is first verified by using the available test results obtained by Chaboche (1989, 1991) for monotonic and cyclic tension loadings on 316 stainless steel. Using the cyclic loading history results under stressand strain-controlled conditions, one can find the metal’s deformational properties.


176

Damage Mechanics

In uniaxial tension-compression loading, the deviatoric stress rate direction always coincides with the normal to the yield surface in this particular example. In addition, since this is a case of proportional loading, the ˙ kinematic hardening rule reduces to Phillip’s rule (1974), that is τ˙ = X. However, it should be noted that for axial proportional loading, the influence of the parameter γ is nullified as shown by equation (6.16), such that l = (τ − B)/ (τ − B)

(6.31)

The parameter γ has an effect only in the cases of non-proportional loadings. The values of m and δ given by equations (6.13) and (6.14), respectively, attain a simpler form for the case of axial loading given as follows: m = 2K

(6.32)

δ = K − (τ − B) : l

(6.33)

The experimental results plotted in Figure 6.3 are obtained by Chaboche (1989, 1991). The value of the coefficients as used by Chaboche (1989, 1991) are given in Table 6.1. For the proposed model, the value of the coefficients is given in Table 2. TABLE 6.1

Value of the coefficients for the Chaboche model (1989, 1991). 316 stainless steel. C1 C2 C3 C4

= 80, 000 MPa = 300, 000 MPa = 1, 600 MPa = 17, 500 MPa

γ1 γ2 γ3 γ4

= 800 = 10, 000 =0 = 350

X = 58 MPa Q0 = 14 MPa QM = 300 MPa µ = 10 b=8

The constants C1 , C2 , γ1 and γ2 in Table 6.2 are obtained through curve fitting with the uniaxial monotonic experimental curve given by Chaboche (1989, 1991). The strain range in this case is one percent. The threshold value of X is directly taken from the evaluation of the Chaboche (1989, 1991) model. This constant is determined by Chaboche (1991) from the ratchetting test. He considered the limit to be slightly below the third mean stress level of 60 MPa.


Plasticity Theory

177

TABLE 6.2

Value of the coefficients for the proposed model. 316 stainless steel. C1 C2 C3 C4

= 80, 000 MPa = 300, 000 MPa = 1, 700 MPa = 17, 000 MPa

γ1 γ2 γ3 γ4

= 1, 000 = 10, 000 = 0.1 = 340


β1 β2 β3 β4

= 0.15 = 0.15 = 0.15 = 0.15

E = 187, 000 MPa ν = 0.30 k = 122.5 MPa

The values of C3 , C4 , γ3 and γ4 are primarily determined by curve fitting the monotonic uniaxial load Chaboche (1989, 1991) for the later part of the strain range beyond one percent stain. These values of C3 , C4 , γ3 and γ4 are further modified to fit with the stress-strain curve for the uniaxial cyclic loading. These final values of the parameters C3 , C4 , γ3 and γ4 are distinctly different from those obtained from the uniaxial monotonic tensile curve. Using these final values of the parameters for uniaxial monotonic loadings yield slightly conservative results. However, they predict more accurately the strains for the cyclic loading case. The coefficients QO , QM , µ and b in Table 6.2 are based on the constants determined by (Chaboche 1989, 1991) in Table 6.1 for the material of type 316 stainless steel. These constants are further modified in order to predict the uniaxial cyclic strains more accurately. The strain amplitudes are kept identical to those of the experimental results (Figure 6.3). The stress saturation level for the same strain amplitude varies with the different values of QO , QM , µ and b. These constants are modified so that it best predicts the stress saturation level for a given strain amplitude in which the material is subjected to uniaxial cyclic loading. The constants β1 , β2 , β3 , β4 are incorporated in order to predict more accurately the strains. The incorporation of β1 , β2 , β3 , β4 allows the flexibility of reducing the stress level in the uniaxial monotonic loading and, therefore, provides a better correlation with the experimental observations. The impact of the constants β1 and β2 is not as significant as that of β3 and β4 on the effect on the predictions of the cyclic loading. The upper bound for β-values is found to be 0.15. If the β-values are taken bigger than 0.15, it may give a better correlation for uniaxial monotonic loading but causes the curved loops in cyclic loading to intersect each other.


178

Damage Mechanics

For the case of cyclic load, the proposed model shown in Figure 6.4 is compared with the experimental observations shown in Figure 6.3 (1989, 1991). Cyclic loading is performed on the model for different strain rages starting from one percent to 3 percent with an increment of strain rate of 0.5 percent. The loading initiates with a cyclic loading of one percent. The cyclic loading is continued until the saturation of stress occurs. Once this saturation occurs for a particular strain range, the strain range is incremented by 0.5 percent and cyclic loading and unloading is performed until saturation of stress and strain occurs for that particular strain range. This is repeated until cyclic loading is performed for the uniaxial case until a 3 percent strain rage is reached. The proposed model gives a better correlation with the experimental results than that proposed by Chaboche (1989, 1991). The shape of the proposed model in Figure 6.4 for cyclic loading

FIGURE 6.3 Experimental results for cyclic stress-strain path with increasing strain levels using the proposed model.(Voyiadjis and Basuroychowdury, 1998)


Plasticity Theory

179

FIGURE 6.4 Simulation of cyclic stress-strain path with increasing strain levels using the proposed model.(Voyiadjis and Basuroychowdury, 1998)

gives a closer correlation with that obtained experimentally in Figure 6.3 than that given by Chaboche (1989, 1991) NLK-T model in Figure 6.5. The cyclic loading loops using the Chaboche model show a very smooth pattern for loading and unloading in the stress-strain diagram. However, in the proposed model the curves show some tapering at the initiation of yielding which is also reflected by the experimental curves. The proposed


180

Damage Mechanics

model also shows a bigger range of variation of the stresses in a constant strain range than that indicated by the Chaboche model. The proposed model is more in line with the experimental results. In the proposed model, the variation of the stresses start at an earlier point for a given strain range as indicated by the experimental data. This is not captured in the Chaboche model (1991).

FIGURE 6.5 Simulation of cyclic stress-strain path with increasing strain levels using the Chaboche model (after Chaboche, 1989, 1991; Voyiadjis and Basuroychowdury, 1998)


Plasticity Theory

6.4

181

Modification of the Kinematic Hardening Model for Non-Proportional Loading

The backstress evolution expressions defined in equations (6.10) are modified here in order to account more appropriately for non-proportional loading paths. The modification involves mainly the replacement of the material constants β (i) with functionally dependent parameters β¯(i) . For non-proportional loading paths, it is clear that the material constant, β (i) , needs to be continuously adjusted as the stress path changes. The scalar proposed functional expression of β¯(i) is expressed in terms of the deviatoric stress tensor direction, the backstress direction, and the direction of the increment of stress. However, for a continuous nonlinear stress path such as a circular stress path, a more involved expression for β¯(i) is required. Such an expression needs to account for the dependence not only on the stress path loading direction but also on the rate of change of the stress path direction. The proposed expressions are given in terms of an angle θ expressed in terms of the current increment of stress lC and the immediate proceeding increment of stress lp . The general expressions for β¯(i) for continuous nonlinear stress paths are given as follows: β¯(1) = (l : s)(1 − sinr θ)β (1)

(6.34)

β¯(2) = (l : s)(1 − sinr θ)β (2)

(6.35)

β¯(3) = (l : s) sinr θ β (3)

(6.36)

β¯(4) = (l : s) sinr θ β (4)

(6.37)

C¯ (i) = C (i)

(6.38)

i = 1, 2, 4

and C¯ (3) = C (3) + (A − C (3) ) sinr θ

(6.39)

Very good correlation is obtained with experimental results using the above expressions for continuously non-proportional loading paths such as circular loading paths. The constants A and r in equations (6.34) to (6.39) depend on the type of material used. The physical interpretation of the scalar (l : s) is to account for the angle between the stress rate (increment of stress) and the direction of dislocations represented here by s. Initially, the authors used X instead of s,


182

Damage Mechanics

however, it did not give as good a correlation with the experimental results as, s, did. The proposed expressions presented here account for hardening increases in both cases, when the degree of multiaxiality increases as well as the degree of non-proportionality increases. The degree of nonproportionality is accounted indirectly through the use of the angle, θ.

6.5

Model Predictions and Comparisons with Experimental Data for Non-Proportional Loadings

Stress-strain relations for combined loadings are used here for evaluating the predictions of the model under non-proportional loading conditions. The performance of the model is compared with the experimental data obtained by Shiratori, et al. (1979) conducted on 60/40 brass. These experiments contain extensive non-proportional loading cases with prestraining. Thin-walled tubular specimens of 60/40 brass are first subjected to a prestrain of 4 percent along the axis of the specimen in order to introduce sufficient anisotropy for testing the proficiency of the model. The stress at the end of the 4 percent prestrain is denoted by σ ¯0 . The tube is then subjected to complex loading paths with various stress bends of loading in the axial-torsional stress space. The axial-torsional subspace may be viewed as a subspace of the Illyushin (1954) five-dimensional deviatoric vector space. The stress vector is defined as follows (Illyushin, 1954): σ = σ1 n1 + σ3 n3

(6.40)

where n1 and n3 are the orthonormal base vectors in the stress space. The components σ1 and σ3 are defined as follows: σ1 = σzz = σ

(6.41)

and σ3 =

√ √ 3σzθ = 3τ

(6.42)

where z and θ denote, respectively, the tube longitudinal and circumferential directions. The corresponding plastic vector is given as follows: = 1 n1 + 3 n3 where


(6.43)

Plasticity Theory

183

1 = zz

(6.44)

2

3 = √ zθ 3

(6.45)

and

The corresponding plastic strain rate vector is defined as follows: ˙ = ˙1 n1 + ˙3 n3

(6.46)

In the axial-torsional subspace, the effective stress is defined such that σe = (σ12 + σ32 )1/2

(6.47)

and the corresponding effective plastic strain accumulation is given by t 2 =

˙ dt (6.48) 3 e 0 where 2 1/2

˙e = ( ˙2 1 + ˙3 )

(6.49)

The material parameters for 60/40 brass of the proposed model are evaluated in a similar fashion to that outlined earlier for the case of 316 stainless steel. The values of the coefficients are given in Table 6.3. TABLE 6.3

Value of the coefficients for 60/40 brass. C1 C2 C3 C4

= 5, 000 MPa = 135, 000 MPa = 50 MPa = 400 MPa

γ1 γ2 γ3 γ4

= 200 = 300 = 0.1 =5


β1 β2 β3 β4

= −0.5 = −0.5 = 0.125 = 0.125

E = 100, 000 MPa ν = 0.3 k = 100 MPa

After the specimens are subjected to a 4 percent prestrain axially, they are then subjected to loading in the σ3 direction or equivalently to a 90 degree stress bend. Thereafter, σe /σ0 versus in percent is plotted. Similar experiments are conducted with 120 degree, 135 degree, 150 degree, and 180 degree stress bends after the 4 percent axial prestraining.


184

Damage Mechanics

FIGURE 6.6 Model comparison with experimental plastic response with 4% prestrain with 90, 120, 135, 150 and 180 degrees stress bends with β (i) given by equations (6.4)-(6.8).(Voyiadjis and Basuroychowdury, 1998)

In Figure 6.6 the response calculated using the proposed model and the experimental observations by Shiratori, et al. (1979) are compared for the different stress bends. The corresponding stress paths are indicated in the figure. In Figure 6.6, the X-axis corresponds to the accumulated plastic


Plasticity Theory

185

strain while the Y-axis corresponds to the equivalent applied stress. Very good correlation is obtained between the response calculated using the proposed model with relations (6.34) - (6.39), and the experimental observations (Shiratori, 1979) for all the stress bends. This is clearly indicated in Figure 6.6. Figure 6.7 compares the equi-plastic surface as given by the proposed model and the experiments (Shiratori, 1979), respectively. The equi-plastic surfaces are constructed at different plastic strain levels of = 0.1, 0.2, 0.5, 1.0, 2.0, both for the experimental and the computed model results after a 4 percent prestrain. The plots are made in the stress space. The proposed model uses an isotropic von Mises yield surface while in reality the yield surface is a distorted anisotropic surface. The use of the von Mises type yield surface avoids the high complexity involved in introducing the anisotropy at the yield surface level. This even becomes more complex when a two-surface anisotropic yield surface model is used and the need is imposed to ensure that the yield surface touches and does not intersect the bounding surface at contact. However, this anisotropy is introduced here through the kinematic hardening with all its resulting complexities. It is clear from the first author’s work by Voyiadjis and Foroozesh (1990) and Voyiadjis; et al. (1995) that introducing anisotropy in kinematic hardening is much simpler than introducing it in the yield surface. The only consequence may be a potential inaccuracy in determining the direction of the plastic strain rates at low values of . Comparing the experimental results with those obtained using the proposed model in Figure 6.7, one notes the following observations. Referring to Figure 6.7, there is a difference in the shape of the plastic potential surfaces at low values of which reduces at an increased since anisotropy is introduced through the kinematic hardening of the model. The proposed additional term in the Armstrong Frederick (1966) model, introduced by the authors, takes care of this additional hardening needed to induce the anisotropic distorted potential surface effect.

6.6

Ratchetting

Ratchetting is the cycle-by-cyc1e accumulation of the plastic strain for some repetitive loading paths. In Figure 6.8, ratchetting is illustrated using a non-proportional loading history. Tubular specimens of 60/40 brass are used in this case (Shiratori, 1979). The strain accumulation due to nonproportional loading is shown in Figure 6.8 for the proposed plasticity model. The ratchetting path is indicated in Figure 6.8, where ∆ t = 1% =


186

Damage Mechanics

FIGURE 6.7 Equi-plastic surfaces - a comparison.(Voyiadjis and Basuroychowdury, 1998) √ ∆γ/ 3 which is the total strain amplitude normalized to the uniaxial case and σd = 67.4 MPa = σ1 which is the constant applied axial stress for the thin walled specimen. The computed response compares reasonably


Plasticity Theory

187

well with the experimental results. However, the decrease in the strain accumulation does not die down as rapidly as in the experimental results.

6.7

Conclusions

A two-surface plasticity model is proposed using a nonlinear hardening rule with evanescent memory evolution. The backstress is calculated as the sum of four components of the type proposed by Chaboche (1989, 1991), the NLK-T model. A new term is added to the Armstrong Frederick (1966) kinematic hardening rule to allow for the motion of the yield surface to be influenced by the direction of the stress rate as proposed by Phillips, et al. (1974). The new term is dependent on the proximity of the yield surface from the bounding surface and on the length of the chord of the bounding surface in the direction of loading. The proposed model is verified by using the available test results obtained by Chaboche (1989, 1991) for monotonic and cyclic tension loadings on 316 stainless steel. This model gives better correlation with the experimental results than the NLK-T model proposed by Chaboche (1989, 1991). The material constant β (i) , used in conjunction with the proposed additional term in the Armstrong Frederick (1966) and Chaboche (1989, 1991) models, is further modified here to account more accurately for nonproportional loading. The constant, β (i) , is replaced here by a functional scalar expression, β¯(i) , in terms of the deviatoric stress tensor direction, the backstress direction, and the direction of the increment of stress. This modification allows the variation of the kinematic hardening as the degree of multiaxiality increases. It also accounts for the nonlinear stress path dependence for the material hardening. The proposed model is tested for non-proportional loading by obtaining numerical results for a series of plastic strain-controlled cyclic tests due to the application of combined axial force and torque to thin-walled tubular specimens of 60/40 brass. The results are compared with the experimental values obtained by Shiratori, et al. (1979). The drift correction due to the finite increments of stress or strain is corrected using an efficient approach that corrects the backstress only. The numerical results obtained compare well with the experimental results (Shiratori, 1979). The model is also tested for both proportional and non-proportional ratchetting. The computed response compares reasonably well with the experimental results. However, the decrease in the strain accumulation does not die down as rapidly as in the experimental results.


188

FIGURE 6.8 Model comparison with experimental ting.(Voyiadjis and Basuroychowdury, 1998)


Damage Mechanics

non-proportional

ratchet-

7 Coupled Damage Plasticity

A constitutive model is developed in this chapter for anisotropic continuum damage mechanics using finite-strain plasticity. The formulation is given in spatial coordinates (Eulerian reference frame) and incorporates both isotropic and kinematic hardening. The von Mises yield function is modified to include the effects of damage through the use of the hypothesis of elastic energy equivalence. A modified elasto-plastic stiffness tensor that includes the effects of damage is derived within the framework of the proposed model. It is also shown how the model can be used in conjunction with other damage-related yield criteria. In particular, Gurson’s yield function (Gurson 1977) which was later modified by Tvergaard (1982) and Tvergaard and Needleman (1984) is incorporated in the proposed theory. This yield function is derived based on the presence of spherical voids in the material and an evolution law for the void growth is also incorporated. It also shows how a modified Gurson yield function can be related to the proposed model. Some interesting results are obtained in this case. For more details, the reader is referred to Kattan and Voyiadjis (1990, 1993, 2001 a,b), Krajcinovic (1983, 1984), Voyiadjis and Kattan (1996), Voyiadjis and Park (1999), and Wilt and Arnold (1994).

7.1

Stress Transformation between Damaged and Undamaged States

Consider a body in the initial undeformed and undamaged configuration Co . Let C be the configuration of the body that is both deformed and damaged after a set of external agencies act on it. Next, consider a fictitious configuration of the body C¯ obtained from C by removing all the damage that the body has undergone. In other words, C¯ is the state of the body after it had only deformed without damage. Therefore, in defining a damage tensor φ, its components must vanish in the configuration C¯ (see Figure 7.1)


189

190

Damage Mechanics

G

dA

(a)

dA

(b)

Fe

Fe

dA*

dA*

G

(c)

(d)

FIGURE 7.1 States of deformation and damage: (a) deformed damage state, (b) fictitious deformed undamaged state, (c) elastically unloaded damaged state (unstressed state), (d) elastically unloaded fictitious undamaged state (fictitious unstressed undamaged state).(Voyiadjis and Kattan, 1999)

7.1.1

Effective Stress Tensor

In the formulation that follows, the Eulerian reference system is used, i.e., all the actual quantities are referred to the configuration C while the effec¯ One first introduces a linear transformation tive quantities referred to C. between the Cauchy stress tensor σ and the effective Cauchy stress tensor ¯ in the following form: σ σ ¯ij = Mijkl σkl

(7.1)

where Mijkl are the components of the fourth-order linear operator called the damage effect tensor. A transformation relation for the deviatoric Cauchy stress tensor is next derived. One first writes the deviatoric part σ in the configuration C as follows:


Coupled Damage Plasticity

191

1 σij = σij − σmm δij (7.2) 3 where δij are the components of the second-order identity tensor I. A ¯ and σ ¯ in the similar relation exists in the configuration C¯ between σ following form: 1 ¯mm δij =σ ¯ij − σ (7.3) σ ¯ij 3 ¯ Substituting for σ ¯ij from equation where δij is the same in both C and C. (7.1) into equation (7.3) while using equation (7.2), we obtain the following: 1 1 σ ¯ij = Mijkl σkl + Mijmm σnn − Mppqr σqr δij (7.4) 3 3 It is clear from equation (7.4) that a linear relation does not exist between ¯ and σ . On the other hand, one might suspect that the last two terms σ on the right-hand side of the equation (7.4) cancel each other when they are written in expanded form. However, this possibility can be easily dismissed = Mijkl σkl . Using this with equation as follows: suppose one assumes σ ¯ij (7.4) one concludes that Mijkl σnn = Mppqr σqr δij . Now consider the case when i = j. One has δij = 0 and, therefore, Mijmm σnn = 0. It is clear that this is a contradiction to the fact that generally Mijmm = 0 and σnn = 0. Therefore, the additional terms in the equation (7.4) are non-trivial and such a linear transformation cannot be assumed. by using Upon examining equation (7.4) in more detail, eliminating σkl equation (7.2) and simplifying the resulting expression, one obtains the following: = Nijkl σkl σ ¯ij

(7.5)

where Nijkl are the components of a fourth-order tensor given by: 1 (7.6) Nijkl = Mijkl − Mrrkl δij 3 Equation (7.5) represents a linear transformation between the effective ¯ and the Cauchy stress tensor σ. Howdeviatoric Cauchy stress tensor σ ever, in this case the linear operator N is not simply the damage effect tensor M but a linear function of M as shown in equation (7.6). The tensors M and N are mappings S → S¯ and S → S¯dev. , respectively, where S is the stress space in the current configuration C and S¯ is the stress space ¯ with σ S and σ ¯ ¯ S. in the fictitious undamaged state C, Next, we consider the effective stress invariants and their transformation ¯ It is seen from equation (7.5) that the first effective in the configuration C. is given by: deviatoric stress invariant σ ¯ii


192

Damage Mechanics = Niikl σkl = 0 σ ¯ii

(7.7)

since Niikl = 0 by direct contraction in equation (7.6). Therefore, one obtains σ ¯ii = σii = 0. The problem becomes more involved when considering the effective stress σ ¯ij . Using equation (7.4) along with equation (7.2), one obinvariant σ ¯ij tains: σ ¯ij = Aklmn σkl σmn + Bpq σpq +C σ ¯ij

(7.8)

where 1 Aklmn = Mijkl Mijmn − Mttmn Mrrkl 3 Bpq =

2 1 σmm (Mijkk Mijpq − Mttpq Mrrnn ) 3 3

(7.9a) (7.9b)

1 1 2 σ (Mijpp Mijqq − Mttmm Mrrnn ) (7.9c) 2 mm 3 Substituting for σ from equation (7.2) into equation (7.8) [or more directly using equation (7.5) along with equation (7.6)], one obtains: C=

σ ¯ij = Hklmn σkl σmn σ ¯ij

(7.10)

where the fourth-order tensor H is given by: Hklmn = Nijkl Nijmn

(7.11)

and the tensor N is given by equation (7.6). The transformation equation (7.10) will be used in the next sections to transform the von Mises yield ¯ criterion into the configuration C.

7.1.2

Effective Backstress Tensor

In the theory of plasticity, kinematic hardening is modeled by the motion of the yield surface in the stress space. This is implemented mathematically by the evolution of the shift or backstress tensor X. The backstress tensor X denotes the position of the center of the yield surface in the stress space. For this purpose, one studies now the transformation of this tensor in the ¯ configuration C and C. Let X be the deviatoric part of X. Therefore, one has the following relation: 1 = Xij − Xmm δij Xij 3 © 2005 by Taylor & Francis Group, LLC

(7.12)


193

where both X and X are referred to the configuration C. Let their effective ¯ be referred to the configuration C. ¯ Similarly to ¯ and X counterparts X equation (7.12), we have: ¯ ij ¯ ij − 1 X ¯ mm δij X =X (7.13) 3 Assuming a linear transformation (based on the same argument used for the stresses) similar to equation (7.1) between the effective backstress ¯ and the backstress tensor X: tensor X

¯ ij = Mijkl Xkl X

(7.14)

and following the same procedure in the derivation of equation (7.5), we ¯ : obtain the following linear transformation between X and X ¯ = Nijkl Xkl X ij

(7.15)

The effective backstress invariants have similar forms to those of the ¯ = X = 0, and effective stress invariants, mainly, X ii ii ¯ ¯ ij Xij = Hklmn Xkl Xmn X

(7.16)

In addition, one more transformation equation needs to be given before we can proceed to the constitutive model. By following the same procedure for the other invariants, the mixed invariant σij Xij in the configuration C ¯ Xij as follows: is transformed to σ ¯ij ¯ Xij = Hklmn σkl Xmn σ ¯ij

(7.17)

¯ σ and a similar relation holds for the invariant X ij ¯ij . The stress and backstress transformation equations will be used later in the constitutive model.

7.2

Strain Rate Transformation between Damaged and Undamaged States

In the general elasto-plastic analysis of deforming bodies, the spatial strain rate tensor d in the configuration C is decomposed additively as follows (Nemat-Nasser, 1979, 1983; Lee, 1981): dke = dkl + dkl

(7.18)

where d and d denote the elastic and plastic parts of d, respectively. In equation (7.18), the assumption of small elastic strains is made, however,


194

Damage Mechanics

finite plastic deformations are allowed. On the other hand, the decomposition in equation (7.18) will be be true for any amount of elastic strain if the physics of elasto-plasticity is invoked, for example the case of single crystals. A thorough account of this is given by Asaro (1983). In the next two subsections, the necessary transformation equations between the configurations C and C¯ will be derived for the elastic strain and plastic strain rate tensors. In this derivation, it is assumed that the elastic strains are small compared with the plastic strains and, consequently, the elastic strain tensor is taken to be the usual engineering elastic strain tensor . In addition, it is assumed that an elastic strain energy function exists such that a linear relation can be used between the Cauchy stress tensor σ and the engineering elastic strain tensor . The tensor is defined here as the linear term of the elastic part of the spatial strain tensor where second-order terms are neglected. For more details, see the work by Kattan and Voyiadjis (1992) and Voyiadjis and Kattan (1999).

7.2.1

Effective Elastic Strain

The elastic constitutive equation to be used is based on one of the assumptions outlined in the previous paragraph and is represented by the following ¯ linear relation in the configuration C: σ ¯ij = E¯ijkl ¯kl

(7.19)

¯ is the fourth-rank elasticity tensor given by: where E E¯ijkl = λδij δkl + G(δik δjl + δil δjk )

(7.20)

where λ and M are Lame’s constants. Based on the constitutive equation (7.19), the elastic strain energy function U ( , φ) in the configuration C¯ is given by: U (¯ , 0) =

1¯ Eijkl ¯ij ¯kl 2

(7.21)

One can now define the complementary elastic energy function V (σ, φ), based on a Legendre transformation, as follows: V (σ, φ) = σij ij − U (¯ , φ)

(7.22)

By taking the partial derivative of equation (7.22) with respect to the stress tensor σ, one obtains:

ij =


∂V (σ, φ) ∂σij

(7.23)


195

Substituting expression (7.21) into equation (7.22) in the configuration ¯ one obtains the following expression for V (σ, φ) in the configuration C¯ C, as follows: ¯ 0) = V (σ,

1 ¯ −1 E σ ¯ij σ ¯kl 2 ijkl

(7.24)

The hypothesis of elastic energy equivalence, which was initially proposed by Sidoroff (1981), is now used to obtain the required relation between and ¯ . In this hypothesis, one assumes that the elastic energy V (σ, φ) in ¯ 0) in the configuration the configuration C is equivalent in form to V (σ, ¯ Therefore, one writes: C. ¯ 0) V (σ, φ) = V (σ,

(7.25)

where V (σ, φ) is the complementary elastic energy in C and is given by: 1 −1 E (φ)σij σkl (7.26) 2 ijkl where the superscript −1 indicates the inverse of the tensor. In the equation (7.26), the effective elasticity modulus E(φ) is a function of the damage tensor φ and is no longer a constant. Using equation (7.25) along with expressions (7.24) and (7.26), one obtains the following relation ¯ and E(φ): between E V (σ, φ) =

−1 −T (φ)E¯ijpq Mpqmn (φ) Eklmn (φ) = Mijkl

(7.27)

where the superscript −T indicates the transpose of the inverse of the tensor −1 Mmnkl = δim δjn . Finally, using equation (7.23) along as depicted by Mijkl with equations (7.24), (7.25), and (7.27), one obtains the desired linear relation between the elastic strain tensor and its effective counterpart ¯ : −T

mn

¯kl = Mklmn

(7.28)

The two transformation equations (7.27) and (7.28) will be incorporated later in this chapter in the general inelastic constitutive model that will be developed.

7.2.2

Effective Plastic Strain Rate

The constitutive model to be developed here is based on a von Mises type yield function f (σ , X , κ, φ) in the configuration C that involves both isotropic and kinematic hardening through the evolution of the plastic work κ and the backstress tensor X , respectively. The corresponding yield func¯, κ ¯ , X tion f (σ ¯ , 0) in the configuration C¯ is given by:


196

Damage Mechanics

3 ¯ kl ¯ kl (¯ σ −X )(¯ σkl −X )−σ ¯o2 − c¯ κ=0 (7.29) 2 kl where σo and c are material parameters denoting the uniaxial yield strength and isotropic hardening, respectively. The plastic work κ is a scalar func¯ is taken here to be in the tion and its evolution in the configuration C, following form: (7.30) d¯ κ = d¯ij d¯ij f=

where dij is the plastic part of the spatial strain rate tensor d. Isotropic hardening is described by the evolution of the plastic work κ as given above. In order to describe kinematic hardening, the Prager¯ Ziegler evolution law (Oldroyd, 1950) is used here in the configuration C, as follows: ¯ ) d¯ αij = d¯ µ(¯ σij −X ij

(7.31)

where d¯ µ is a scalar function to be determined shortly. The plastic flow in the configuration C¯ is described by the associated flow rule in the form: ¯ ∂f d¯ij = dΛ ∂σ ¯ij

(7.32)

¯ is a scalar function introduced as a Lagrange multiplier in the where dΛ constraint thermodynamic equations (see section 7.3), that is still to be determined. In the present formulation, it is assumed that the associated flow of plasticity will still hold in the configuration C, that is: dij = dΛ

∂f ∂σij

(7.33)

where dΛ is another scalar function that is to be determined. Substituting the yield function f of equation (7.29) into equation (7.32) and using the transformation equations (7.5) and (7.15), one obtains: ¯ ijkl (σkl − Xkl ) d¯ij = 3dΛN

(7.34)

On the other hand, substituting the yield function f of equation (7.29) into equation (7.33) and noting the appropriate transformation (7.10) and (7.16), one obtains: dij = 3dΛHijkl (σkl − Xkl )

(7.35)

It is noticed that plastic incompressibility exists in the configuration C¯ as seen from equation (7.34) where d¯mm = 0 since Nmmkl = 0. However,



197

this is not true in the configuration C since dmm does not vanish depending on Hmmkl as shown in equation (7.35). ¯ , one In order to derive the transformation equation between d and d first notices that: ∂f ∂ σ ∂f ∂f ¯pq = = Mpqij ∂σij ∂σ ¯pq ∂σij ∂σ ¯pr

(7.36)

where Mpqij is defined in the equation (7.1) as ∂ σ ¯pq /∂σij . Using the above relation along with equations (7.32) and (7.33), one obtains: ¯ dΛ M −1 d d¯ij = dΛ ijmn mn

(7.37)

The above equation represents the desired relation, except that the ex¯ pression dΛ/dΛ needs to be determined. This is done by finding explicit ¯ using the consisting conditions. The rest expressions for both dΛ and dΛ of this section is devoted to this task. But first one needs to determine an appropriate expression for d¯ µ that appears in equation (7.31), since it ¯ plays an essential role in the determination of dΛ. In order to determine an expression for d¯ µ, one assumes that the pro¯ on the gradient of the yield surface f in the stress space is jection of dX ¯ where b is a material parameter to be ¯ in the configuration C, equal to bd determined from the uniaxial tension test (Voyiadjis, 1984; Voyiadjis and Kiousis, 1987). This assumption is written as follows: ¯ mn bd¯kl = dX

∂f ∂σ ¯ mn ∂f ∂f ∂σ ¯ pq ∂ σ ¯ pq

∂f ∂σ ¯kl

(7.38)

¯ and d from equation (7.31) and (7.32), respecSubstituting for dX tively, into equation (7.38) and post-multiplying the resulting equation by µ: ∂f /∂ σ ¯kl , one obtains the required expression for d¯ ¯ d¯ µ = bdΛ

∂f ∂f ∂σ ¯ mn ∂ σ ¯ mn −X ) ∂f ¯ pq (¯ σpq ∂σ ¯ pq

(7.39)

Using the elastic linear relationship in equation (7.19), and taking its rate, one obtains: ¯ijkl d¯kl d¯ σij = E

(7.40)

where d¯kl is assumed to be equal to d¯

kl based on the assumption of small ¯ from equation elastic strains as discussed in section 7.2.1. Eliminating d (7.40) through the use of expressions (7.18) and (7.32), one obtains:


198

Damage Mechanics

¯ijkl (d¯kl − dΛ ¯ ∂f ) d¯ σij = E (7.41) ∂σ ¯kl ¯ , ¯ is obtained from the consisting condition df (¯ ,X The scalar multiplier dΛ σkl kl 0, κ ¯) = 0 such that: ∂f ∂f ¯ + ∂f d¯ κ=0 σkl + ¯ dX kl d¯ ∂σ ¯kl ∂¯ κ ∂ Xkl

(7.42)

Using equations (7.18), (7.30), (7.32), (7.39), and (7.41) into equation ¯ (7.42), one obtains the following expression for dΛ: ¯klmn d¯mn ¯ = 1 ∂f E dΛ ¯ ∂σ ¯kl Q

(7.43)

¯ is scalar and given by: where Q ¯abcd ∂f − ∂f ¯ = ∂f E Q ∂σ ¯ab ∂σ ¯cd ∂¯ κ

∂f

∂f

∂f ∂f ∂f ∂σ ¯ ij ∂ σ ¯ ij ¯ ef −b ¯ (¯ σ −X ) ¯ ∂σ ¯pq ∂ σ ¯pq ∂ Xef ef (¯ σgh − Xgh ) ∂∂f σ ¯

gh

(7.44) Assuming that the Prager-Ziegler kinematic hardening rule holds in the configuration C along with the projection assumption of equation (7.13), one can derive a similar equation to (7.43), in the following form: dΛ =

1 ∂f Eklmn dmn Q ∂σkl

(7.45)

where Q is given by: ∂f ∂f ∂f Q= Eabcd ∂σ − ∂κ ∂σab cd

∂f

∂f

∂f ∂f ∂f ∂σij ∂σi j −b (σef −Xef ) ) ∂f ∂σpq ∂σpq ∂Xef (σgh − Xgh ∂σ

gh

(7.46) In contrast to the method used by Voyiadjis and Kattan (1990) where the two yield functions in the configurations C and C¯ are assumed to be equal, a more consistent approach is adopted here. This approach is based on the assumptions used to derive equation (7.45). It is clear that in this method, the two yield functions in the configurations C and C¯ are treated separately and two separate consistency conditions are thus invoked. In the authors’ opinion, this emphasizes a more consistent approach than the method used by Voyiadjis and Kattan (1990). One is now left with the tedious algebraic manipulations of equations ¯ (7.43) and (7.45) in order to derive an appropriate form for the ratio dΛ/dΛ.



199

First, equation (7.45) is rewritten in the following form, where the appro¯ → E and σ → σ ¯ are used: priate transformations E QdΛ =

∂f ¯ −T Eijpq Mpqmn dmn ∂σ ¯ij

(7.47)

Then, one expands equation (7.43) by using the appropriate transforma¯ → d and d ¯ → d to obtain: tions d ¯ ¯ = 1 ∂f E¯klmn [dM −T E −1 σij +M −T dpq −(M −T − dΛ M −1 )d ] dΛ mnpq ijpq mnpq mnpq ¯ ¯kl dΛ mnpq pq Q ∂σ (7.48) where the derivative dMmnpq is defined in the next section. The last major step in the derivation is to substitute the term on the right-hand side ¯ σ → of equation (7.47) for the results using the transformations σ → σ, ¯ and others. Once this is done, the following relation is obtained: ¯ , E → E, σ ¯− (Q

∂f ∂f ¯ ¯ = (Q − ∂f Eijpq ∂f )dΛ Eklmn )dΛ ∂σ ¯kl ∂σ ¯mn ∂σij ∂σpq +

∂f ¯ −1 −T Eklmn dMmnpq Eijpq σij ∂σ ¯kl

(7.49)

The above equation is rewritten in the form: ¯ = a2 dΛ + a3 a1 dΛ

(7.50)

where ¯− a1 = Q

∂f ∂f ¯ Eklmn ∂ σ ∂σ ¯kl ¯mn

(7.51a)

a2 = Q −

∂f ∂f Eklmn ∂σkl ∂σmn

(7.51b)

a3 =

∂f ¯ −1 −T Eklmn dMmnpq Eijpq σij ∂σ ¯kl

(7.51c)

It is noticed that a1 and a2 are the last two terms on the right-hand sides of equations (7.44) and (7.46), respectively. It should be noted that when the material undergoes only plastic deformation without damage, that is when the configurations C and C¯ coincide, then a1 = a2 and a3 = 0 since dM vanishes in this case, thus leading to ¯ = dΛ. dΛ


200

Damage Mechanics

The relation (7.50) is now substituted into equation (7.37) along with equation (7.35) to obtain the following nonlinear transformation equation for the plastic part of the spatial strain rate tensor: d¯ij = Xijkl dkl + Zij

(7.52)

where the tensors X and Z are given by: a2 −1 M a1 ijkl

(7.53)

a3 −1 M Hklmn (σmn − Xmn ) a1 ijkl

(7.54)

Xijkl =

Zij = 3

The transformation equation (7.52) will be used later in the derivation of the constitutive equations.

7.3

Constitutive Model

In this section, a coupled constitutive model will be derived incorporating both elasto-plasticity and damage. This section is divided into three subsections detailing the derivation starting with the equations then proceeding to the desired coupling.

7.3.1

Damage Evolution

In this section, an inelastic constitutive model is derived in conjunction with the damage transformation equations presented in the previous sections. An elasto-plasticity stiffness tensor that involves damage effects is derived in the Eulerian reference system. In this formulation, rate-dependent effects are neglected and isothermal conditions are assumed. The damage evolution criterion to be used here is that proposed by Lee et al. (1985) and is given by: ¯ L) = g(σ,

1 Jijkl σ ¯ij σ ¯kl − lo2 − L(l) ≡ 0 2

(7.55)

where Jijkl are the components of a constant fourth-order tensor that is symmetric and isotopic. This tensor is represented by the following matrix:


Coupled Damage Plasticity ⎡

1 ⎢µ ⎢ ⎢µ J≡⎢ ⎢0 ⎢ ⎣0 0

µ 1 µ 0 0 0

201 ⎤ µ 0 0 0 ⎥ µ 0 0 0 ⎥ ⎥ 1 0 0 0 ⎥ ⎥ 0 2(1 − µ) 0 0 ⎥ ⎦ 0 0 2(1 − µ) 0 0 0 0 2(1 − µ)

(7.56)

where µ is a material constant satisfying − 21 ≤ µ ≤ 1. In equation (7.55), lo represents the initial damage threshold, L(l) is the increment of damage threshold, and l is the scalar variable that represents overall damage. During the process of plastic deformation and damage, the power of dissipation Π is given by (Voyiadjis and Kattan, 1990): Π = σij dij + σkl dφkl − Ldl

(7.57)

In order to obtain the actual values of the parameters σ, φ, κ, and l, one needs to solve an extremization problem, i.e, the power of dissipitation Π is to be extremized subject to two constraints, namely, f (σ , X , κ, φ) = 0 ¯ L) = 0. Using the method of the calculus of functions of several and g(σ, variables, one introduces two Lagrange multipliers dλ1 , and dλ2 , and forms the function Ψ such that: Ψ = Π − dλ1 f − dλ2 g

(7.58)

The problem now reduces to that of extremizing the function Ψ. Therefore, one uses the necessary conditions ∂Ψ/∂σ = 0 and ∂Ψ/∂L = 0 to obtain: dij + dφij − dλ1

∂f ∂g − dλ2 =0 ∂σij ∂σij

−dl − dλ2

∂g =0 ∂L

(7.59a)

(7.59b)

Next, one obtains from equation (7.55) that ∂g/∂L = −1. Substituting this into equation (7.59b), one obtains dλ2 = dl. Thus dλ2 describes the evolution of the overall damage parameter l which is to be determined shortly. Using equation (7.59b) and assuming that damage and plastic deformation are two independent processes, one obtains the following two rate equations for the plastic strain and damage tensors: dij = dλ1


∂f ∂σij

(7.60a)

202

Damage Mechanics

dφij = dl

∂g ∂σij

(7.60b)

The first equation of (7.60) is the associated flow rule for the plastic strain introduced earlier in equation (7.33), while the second is the evolution of the damage tensor. It is to be noted that dλ1 is exactly the same as the multiplier dΛ used earlier. However, one needs to obtain explicit expressions for the multipliers dΛ and dl. The derivation of an expression for dΛ will be left for the next section when the inelastic constitutive model is discussed. Now one proceeds to derive an expression for dl. This is done by invoking the consistency condition dg(σ, φ, L) = 0. Therefore, one obtains: ∂g ∂g ∂g dL = 0 dσij + dφkl + ∂σij ∂φkl ∂L

(7.61)

Substituting for dφ from equation (7.60b) along with ∂g/∂L = −1 and dL = dl(∂L/∂l), we obtain: dl =

∂g ∂σij ∂L ∂l

−

dσij

∂g ∂g ∂φpq ∂σpq

(7.62)

Finally, by substituting equation (7.62) into equation (7.60b), we obtain the general evolution equation for the damage tensor φ as follows: dφkl =

∂g ∂σij dσij ∂g ∂g ∂L ∂l − ∂φpq ∂σpq

∂g ∂σkl

(7.63)

The evolution equation (7.63) is to be incorporated in the constitutive model in the next two sections. It will also be used in the derivation of the elasto-plastic stiffness tensor. It should be noted that equation (7.63) is based on the damage criterion of equation (7.55) which is applicable to anisotropic damage. However, using the form for J given in equation (7.56) restricts the formulation to isotropy.

7.3.2

Plastic Deformation

In the analysis of finite strain plasticity, one needs to define an appropriate corotational stress rate that is objective and frame-indifferent. Detailed discussions of the types of stress rates are available in the papers of Voyiadjis and Kattan (1989) and Paulun and Pecherski (1985). The corotational stress rate to be adopted in this model is given for σ in the following form: ◦

σ ij = dσij − Ωip σpj + σiq Ωqj


(7.64)


203

where the modified spin tensor Ω is given by (Paulun and Pecherski, 1985; Voyiadjis and Kattan, 1989) as follows: Ωij = ωWij

(7.65)

In equation (7.65), W is the material spin tensor (the antisymmetric part of the velocity gradient) and ω is an influence scalar function too be determined. The effect of ω on the evolution of the stress and backstress is discussed in detail by Voyiadjis and Kattan (1989). The corotational rate ◦ α has a similar expression as that in equation (7.64) keeping in mind that the modified spin tensor Ω remains the same in both equations. The yield function to be used in this model is the function f given by equation (7.29) with both isotropic and kinematic hardening. Isotropic hardening is described by the evolution of the plastic work as given earlier by equation (7.30), while kinematic hardening is given by equation (7.31). Most of the necessary plasticity equations were given in section 7.2.2 and the only thing remaining is the derivation of the constitutive equation. ¯ from equation (7.43) into equation (7.41), one By substituting for dΛ derives the general inelastic constitutive equation in the configuration C¯ as follows: ¯ ijkl d¯kl d¯ σij = D

(7.66)

where the elasto-plastic stiffness tensor D is given by: ¯mnkl E¯ijpq ∂f ¯ ijkl = E ¯ijkl − 1 ∂f E D ¯ ∂σ ¯mn ∂σ ¯pq Q

(7.67)

The next step is to use the transformation equations developed in the previous sections in order to obtain a constitutive equation in the configuration C similar to equation (7.66).

7.3.3

Coupling of Damage and Plastic Deformation

In this section, the transformation equations developed in sections 7.1 and 7.2 are used with the constitutive model of the previous section in order to transform the inelastic constitutive equation (7.66) in the configuration C¯ to a general constitutive equation in the configuration C that accounts for both damage and plastic deformation. Using equation (7.28) and taking its derivative, one obtains the following ¯ : transformation equation for d −T −T d¯ij = dMijmn

mn + Mijkl dkl


(7.68)

204

Damage Mechanics

where dM−T is obtained by taking the derivative of the identity MT M−T = I and noting that dI = 0. Thus, one has: −T −T T −T dMklmn = −Mijkl dMijpq Mpqmn

(7.69)

The derivative dM is obtained by using the chain rule as follows: dMijpq =

∂Mijpq dφmn ∂φmn

(7.70a)

◦

Also, the corotational derivative M may be used defined by the following Lie derivative given by Oldroyd (1950): ◦

M ijmn = dMijmn − Ωip Mpjmn − Ωjq Miqmn − Ωmr Mijrn − Ωns Mijms (7.70b) The transformation equation (7.68) for the effective elastic strain rate ¯ represents a nonlinear relation unlike that of the effective stress tensor d tensor of equation (7.1). A similar nonnlinear transformation equation (7.52) was previously derived for the effective plastic strain d . These two equations will now be used in the derivation of the constitutive model. Now we are ready to derive the inelastic constitutive relation in the configuration C. Starting with the constitutive equation (7.66) and substituting for σ ¯ij and d¯kl from equations (7.1) and (7.18), respectively, along with equations (7.68) and (7.52), we obtain: ¯ ijkl (M −T d +dM −T +Xklmn d +Zkl ) dMijmn σmn +Mijpq dσpq = D mn klmn mn klpq pq (7.71) Next, we substitute for dM and dM−T from equations (7.70) and (7.69), respectively, for d from equation (7.18), and for d from a similar equation −1 to (7.40), i.e., dij = Eijkl dσkl , into equation (7.71), the resulting expression is: ∂Mijmn ¯ ijkl (M −T E −1 dσpq − dφpq σmn + Mijpq dσpq = D klmn pqmn ∂φpq T ∂Mxyuv −1 −1 dφmn Muvpq Ecdpq σcd + Xklmn dmn − Xklmn Eabmn dσab + Zkl ) ∂φmn (7.72) Finally, we substitute for dφ from equation (7.63) into equation (7.72) and solve for dσ in terms of d. After several algebraic manipulations, we obtain the desired inelastic constitutive relation in the configuration C as follows: −T Mxykl



205

dσij = Dijkl dkl + Gij

(7.73)

where the effective elasto-plastic stiffness tensor D and the additional tensor G (comparable to the plastic relaxation stress introduced by Simo and Ju (1987)) are given by: −1 ¯ Dpqmn Xmnkl Dijkl = Opqij

(7.74a)

−1 ¯ Dpqmn Zmn Gij = Opqij

(7.74b)

where the fourth-order tensor O is given by:

Oijpq = Mijpq + −T −Mxykl

∂Mijmn ∂g ∂g ∂φuv ∂σpq ∂σuv σmn ∂g ∂g ∂L ∂l − ∂φxy ∂σxy −T ∂Mxyuv ∂φmn

−1 −1 ¯ ijkl (M −T Epqmn −D − Xklmn Epqmn klmn

∂g ∂g ∂σpq ∂σmn ∂g ∂g ∂L ∂l − ∂φab ∂σab

−T −T Muvcd Mrscd σrs )

(7.75)

The effective elasto-plastic stiffness tensor D in equation (7.74a) is the stiffness tensor including the effects of damage and plastic deformation. It is derived in the configuration of the deformed and damaged body. Equations (7.74) can now be used in finite element analysis. However, it should be noted that the constitutive relation in equation (7.73) represents a nonlinear transformation that makes the numerical implementation of this model impractical. This is due to the additional term Gij which can be considered as some residual stress due to the damaging process. Nevertheless, the constitutive equation becomes linear provided that Gij = 0. This is possible only when the term (σmn − Xmn )Nijrr vanishes as seen in equations (7.74b) and (7.54) and therefore: dσij = Dijkl dkl

(7.76)

Upon investigation of the nonlinear constitutive equation (7.73), it is seen that the extra term Gij is due to the linear transformation of the ¯ in equation (7.1). It was shown in equation (7.4) effective stress σ and σ ¯ . that this transformation leads to a nonlinear relation between σ and σ The authors have shown in a recent work (Voyiadjis and Kattan, 1999) that a linear constitutive equation similar to equation (7.76) can be obtained if a linear transformation is assumed between the deviatoric stresses σ and ¯ in the form σ σ ¯ij = Mijkl σkl .


206

Damage Mechanics

For completeness, one can obtain an identity that may be helpful in the numerical calculations. This is done by using the plastic volumetric incompressibility condition (which results directly from equation (7.34)): d¯kk = 0

(7.77)

¯ Equation (7.77) is commonly used in metal plasticin the configuration C. ity without damage (Paulun and Pechervski, 1985; Voyiadjis ans Kattan, 1989). Using equation (7.34) along with the condition (7.77), one obtains the useful identity: ◦ − Xkl ) = 0 Nrrkl (σkl

(7.78)

Equation (7.78) is consistent with the previous conclusion of equation (7.7) since it was shown earlier that Nrrkl = 0. In finite element calculations the critical state of damage is reached when the overall parameter l reaches a critical value called lcr in at least one of the element. This value determines the initiation of microcracks and other (1) damaging defects. Alternatively, one can assign several critical values lcr , (2) lcr , etc. for different damage effects. In order to determine these critical values, which may be considered as material parameters, a series of uniaxial extension tests are to be performed on tensile specimens and the stressstrain curves drawn. (i) In order to determine lcr (the value of l at which damage initiation starts for a particular damage process ”i”), the tensile specimen has to be sectioned at each load increment. The cross-section is to be examined for any cracks or cavities. The load step when cracks first appear in terms of the strain 1 is to be recorded and compared with the graph of l vs 1 . The corresponding value of l obtained in this way will be taken to be the critical value for lcr . This value is to be used in the finite element analysis of more complicated problems. For more details, see the papers by Chow and Wang (1988) and Voyiadjis (1984, 1988).

7.4

Application to Void Growth: Gurson’s Model

Gurson (1977) proposed a yield function f (σ, v) for a porous solid with a randomly distributed volume fraction of voids. Gurson’s model was used later (Tvergaard, 1982; Tvergaard and Needleman, 1984) to study necking and failure of damaged solids. Tvergaard and Needleman (1984) modified Gurson’s yield function in order to account for rate sensitivity and necking



207

instabilities in plastically deforming solids. The modified yield function is used here in the following form (which includes kinematic hardening): − Xij )(σij − Xij ) + 2q1 σF2 v cosh( f = (σij

σkk ) − σF2 (1 + q2 v 2 ) = 0 (7.79) 2σF

where σF is the yield strength of the matrix material and q1 and q2 are material parameters introduced by Tvergaard (1982) to improve agreement between Gurson’s model and other results. In equation (7.79), the variable v denotes the void volume fraction in the damaged material. In Gurson’s model, damage is characterized by void growth only. The void growth is described by the rate of change of v given by (Voyiadjis, 1988): dν = (1 − ν)dkk

(7.80)

In Gurson’s model, it is assumed that the voids remain spherical in shape through the whole process of deformation and damage. The change of shape of voids, their coalescence and nucleation of new voids are ignored in the model. Equation (7.80) implies also that the plastic volumetric change, dkk , does not vanish for a material with voids. In the following, it is shown how the proposed model outlined in the first sections of this chapter can be used to obtain the damage effect tensor M as applied to Gurson’s yield function. It is also shown how certain expressions can be derived for the parameters q1 and q2 in a consistent manner. One first starts with the yield function f in the configuration C. Therefore, using equation (7.29) in the form: 2 2 ¯ )(¯ ¯ ¯ (7.81) f = (σ¯ mn − X mn σmn − Xmn ) − σ 3 o where the term c¯ κ is dropped since isotropic hardening is not displayed by Gurson’s function. Using the transformation equations (7.10), (7.16), and (7.17) and noting that σF2 = 2¯ σo2 /3, equation (7.81) becomes: f = Hijkl (σij − Xij )(σkl − Xkl ) − σF2

(7.82)

It is noticed that equation (7.81) corresponds exactly to Gurson’s function of equation (7.79) with v = 0. Using equation (7.2) and (7.12) to transform the total stresses in equation (7.82) into deviatoric stresses, one obtains: 1 f = Hijkl (σij − Xij )(σkl − Xkl ) + Hmmnn (σpp − Xqq )2 − σF2 9

(7.83)

Equation (7.83) represents the yield function f in the configuration C, which can now be compared to Gurson’s yield function of equation (7.79).


208

Damage Mechanics

Thus, upon comparing equation (7.79) with equation (7.83) , it is clear that the deviatoric parts of the two functions must be equal. Therefore, one obtains: − Xij )(σkl − Xkl ) = (σrs − Xrs )(σrs − Xrs ) Hijkl (σij

(7.84)

On the other hand, upon equating the remaining parts of the two functions, one obtains: 1 σkk Hmmnn (σpp − Xqq )2 = 2q1 σF2 v cosh( ) − q2 σF2 v 2 9 2σF

(7.85)

The problem is now reduced to manipulating equations (7.84) and (7.85). Rewriting equation (7.84) in the following form: (Hijkl − δik δjl )(σij − Xij )(σkl − Xkl )=0

(7.86)

One concludes that the tensor H is constant for Gurson’s model and can be expressed as follows: Hijkl = δik δjl

(7.87)

It is clear that the deviatoric part of Gurson’s yield function does not display any damage characteristics as given by equation (7.79). This is further supported by equation (7.87) where the damage effect tensor is independent of the damage variable φ. Next, upon considering equation (7.87), one obtains Hmmnn = 3. Substituting this value into equation (7.85) yields: 1 σkk (σpp − Xqq )2 = [2q1 cosh( ) − q2 v]vσF2 3 2σF

(7.88)

Equation (7.88) must be satisfied for a possible relationship between Gurson’s model and the proposal model. Equation (7.88), as it stands, does not seem to merit an explicit relationship between parameters q1 , q2 , and v. This is due to the presence of the “cosh” term on the right-hand side. Therefore, it is clear that one cannot proceed further without making some assumptions. In particular, two assumptions are to be employed. The first assumption is valid for small values of σkk /(2σF ), where only the first two terms in the “cosh” series expansion are considered: cosh(

σkk σ2 ) = 1 + kk2 2σF 8σF

(7.89)

The second assumption concerns the term Xqq which appears in the equation (7.88). For the following to be valid, one needs to consider a modified Gurson yield function where the volumetric stress σkk is replaced



209

by (σkk − Xqq ). Therefore, upon incorporating the above two assumptions into equation (7.88), one obtains: 1 1 (σkk − Xqq )2 = q1 v(σkk − Xqq )2 + (2q1 − q2 v)vσF2 (7.90) 3 4 It is now clear from the equation (7.90) that the following two expressions for q1 and q2 in terms of v, need to be satisfied: q1 =

4 3v

(7.91a)

8 (7.91b) 3v 2 The relations (7.91a,b) represent variable expressions for the parameters q1 and q2 in terms of the void volume fraction, in contrast to the constant values that were suggested earlier by various authors. The relations (7.91a,b) are consistently derived and although they are approximate, in the authors’ opinion, they form a basis for more sophisticated expressions. In addition, they are based on a solid derivation which cannot be said for the constant values that were used in the literature. Finally, one more important point that came up in the derivation needs to be considered. As it stands, Gurson’s function of equation (7.79) cannot be related to the work presented here. It is a modified version of Gurson’s function containing the term cosh[(σkk − Xqq )/(2σF )] instead of cosh[σkk /(2σF )] that is used in the derivation of equations (7.91a,b). The authors believe that this point should be pursued and the proposed modified Gurson function explored further. q2 =

7.5

Effective Spin Tensor

In this section, a formal derivation is presented for the transformation equation of the modified spin tensor that is used in the corotational rate ¯ the corotational derivative of the effecequations. In the configuration C, tive Cauchy stress tensor is given by: ◦

¯ qj ¯ ip σ σ ¯ ij = d¯ σij − Ω ¯pj + σ ¯iq Ω

(7.92)

¯ is the effective modified spin tensor. The problem now reduces to where Ω ¯ One should keep in mind, however, finding a relation between Ω and Ω. that equation (7.92) is valid only when a Cartesian coordinate system is used. The same remark applies to equation (7.64) in the configuration C.


210

Damage Mechanics

In order to derive the required relation, one first starts with the transformation equation (7.1). Taking the corotational derivative of this equation and rearranging the terms, one obtains: ◦

◦

◦

−1 σ ke = Mijke (σ ¯ ij − M ijmn σmn )

(7.93)

◦

¯ ij from equation (7.92) into equation (7.93) and using Substituting for σ the material time derivative dσij = dMijrs σrs + Mijpq dσpq , one obtains: ◦ −1 −1 ¯ −1 ¯ qj σ kl = Mijkl Ωip Mpjab σab + Mijkl dMijrs σrs + dσkl − Mijkl Miqcd σcd Ω −1 −Mijkl Mijmn σmn

(7.94)

Comparing the two corotational derivatives appearing in equations (7.64) and (7.94), and after performing some tedious algebraic manipulations, one ¯ in the following form: can finally obtain a relation between Ω and Ω ¯ mn = Amnpq Ωpq + Bmn Ω

(7.95)

where the tensors A and B are given by: −1 (δkp σql − δlq σkp ) Amnpq = −Cmnkl ◦

−1 −1 Bmn = −Cmnkl Mpqkl (dMpqrs − M pqrs )σrs

(7.96a) (7.96b)

and the tensor C is given by: −1 −1 Mqicd − Mijkl Mpjcd )σcd Cklip = (Mqpkl

(7.96c)

With the availability of the transformation equation of the spin tensor, the theory presented in this chapter is now complete.

Problems 7.1. Explain why equation (7.4) does not represent a linear transformation? 7.2. Derive equation (7.6) explicitly. 7.3. Derive equations (7.8) and (7.9) explicitly. 7.4. Derive equation (7.11) explicitly. 7.5. Derive equations (7.27) and (7.28) explicitly.



211

7.6. Assume a linear transformation in the form σ ¯ij = Mijkl σkl . Derive the corresponding elasto-plastic constitutive model for this case. Specifically, derive a new elasto-plastic stiffness tensor Dijkl .

7.7. Derive equations (7.34) and (7.35) explicitly. 7.8. Derive equation (7.43) explicitly. 7.9. Derive equation (7.45) explicitly. 7.10. Derive equations (7.50) and (7.52) explicitly. 7.11. Consider a von Mises type yield function of the form given by equation (7.29). Neglect isotropic hardening and derive a new elasto-plastic constitutive model based on the modified yield criterion. 7.12. Consider a von Mises type yield function of the form given by equation (7.29). Neglect kinematic hardening and derive a new elasto-plastic constitutive model based on the modified yield criterion. 7.13. Consider a von Mises type yield function of the form given by equation (7.29). Neglect both isotropic and kinematic hardening, and derive a new elasto-plastic constitutive model based on the modified yield criterion. 7.14. Explore using a Tresca type yield function instead of a von Mises in the formulation of the elasto-plastic constitutive model given in this chapter. 7.15. Consider using a different damage evolution criterion by introducing the generalized force Yij associated with φij in the equation (7.55). Derive a new evolution equation for the damage variable φ in this case. 7.16. Derive equations (7.62) and (7.63) explicitly. 7.17. Derive equation (7.67) explicitly. 7.18. Derive equation (7.70b) explicitly. 7.19. Derive equations (7.73), (7.74) and (7.75) explicitly. 7.20. Explain why there is an additional term Gij in the elasto-plastic constitutive equation (7.73). What are the conditions under which this term vanishes. 7.21. Derive equations (7.87) and (7.88) explicitly. 7.22. Derive equation (7.89) explicitly.


212 7.23. Derive equation (7.91a,b) explicitly. 7.24. Derive equations (7.95) and (7.96) explicitly.


Damage Mechanics

8 Kinematics of Damage for Finite-Strain Elasto-Plastic Solids

In this chapter, the kinematics of damage for finite strain elasto-plastic deformation is introduced using the fourth-order damage effect tensor through the concept of the effective stress within the framework of continuum damage mechanics. In the absence of the kinematic description of damage, deformation leads one to adopt one of the following two different hypotheses for the small deformation problems. One uses either the hypothesis of strain equivalence or the hypothesis of energy equivalence in order to characterize the damage in the material. The proposed approach in this chapter provides a general description of kinematics of damage applicable to finite strains. This is accomplished by directly considering the kinematics of the deformation field and, furthermore, noting that it is not confined to small strains as in the case of the strain equivalence or the strain energy equivalence approaches. In this chapter, damage is described kinematically in both the elastic domain and the plastic domain using the fourth-order damage effect tensor, which is a function of the second-order damage tensor. The damage effect tensor is explicitly characterized in terms of a kinematic measure of damage through a second-order damage tensor. Two kinds of second-order damage tensor representations are used with respect to two reference configurations. The finite elasto-plastic deformation behavior with damage is also viewed here within the framework of thermodynamics with internal state variables. Using the consistent thermodynamic formulation, one introduces separately the strain due to damage and the associated dissipation energy due to this strain.

8.1

Theoretical Preliminaries

A continuous body in an initial undeformed configuration that consists of the material volume Ωo is denoted by C o , while the elasto-plastic damaged deformed configuration at time t after the body is subjected to a set of


213

214

Damage Mechanics

external agencies is denoted by C t . The corresponding material volume at time t is denoted by Ωt . Upon elastic unloading from the configuration C t an intermediate stress-free configuration is denoted by C dp . In the framework of continuum damage mechanics, a number of fictitious configurations, based on the effective stress concept, are assumed that are obtained by fictitiously removing all the damage that the body has undergone. Thus, the fictitious configuration of the body denoted by C¯ t is obtained from C t by fictitiously removing all the damage that the body has undergone at C t . Also, the fictitious configuration denoted by C¯ p is assumed which is obtained from C dp by fictitiously removing all the damage that the body has undergone at C dp . While the configuration C¯ p is the intermediate configuration upon unloading from the configuration C¯ t , the initial undeformed body may have a pre-existing damage state. The initial fictitious effective configuration denoted by C¯ o is defined by removing the initial damage from the initial undeformed configuration of the body. In the case of no initial damage existing in the undeformed body, the initial fictitious effective configuration is identical to the initial undeformed configuration. Cartesian tensors are used in this chapter and the tensorial index notation is employed in all equations. The tensors used in the text are denoted by boldface letters. However, superscripts in the notation do not indicate tensorial indices but merely stand for the corresponding deformation configurations such as “e” for elastic, “p” for plastic, and “d” for damage, etc. The barred and tilded notations refer to the fictitious effective configurations.

8.2

Description of Damage State

The damage state can be described using an even order tensor (Leckie, 1993; Onat, 1986; Betten, 1986). Ju (1990) pointed out that even for isotropic damage one should employ a damage tensor (not a scalar damage variable) to characterize the state of damage in materials. However, the damage generally is anisotropic due to the external agency condition or the material nature itself. Although the fourth-order damage tensor can be used directly as a linear transformation tensor to define the effective stress tensor, it is not easy to characterize physically the fourth-order damage tensor compared with the second-order damage tensor. In this chapter, the damage is considered as a symmetric second-order tensor. However, the damage tensor for finite elasto-plastic deformation can be defined in two reference systems (Murakami, 1988). The first one is the damage tensor denoted by φ representing the damage state with respect to the current


Kinematics of Damage for Finite-Strain Elasto-Plastic Solids

215

damage configuration C t . Another one is denoted by φ¯ and is representing the damage state with respect to the elastically unloaded damage configuration C dp (see Chapter 3). Both are given by Murakami (1983) as follows: φij =

3

ˆ ki n ˆ kj (no sum over k) φˆk n

(8.1)

ˆ ki m ˆ kj (no sum over k) φˆ¯k m

(8.2)

k=1

φ¯ij =

3 k=1

where n ˆ k and m ˆ k are eigenvectors corresponding to the eigenvalues, φˆk ¯ ¯ respectively. Equations (8.1) and and φˆk , of the damage tensors φ and φ, (8.2) can be written alternately as follows: φij = bir bjs φˆrs

(8.3)

φ¯ij = cir cjs φˆ¯rs

(8.4)

The damage tensors in the coordinate system that coincides with the three orthogonal principal directions of the damage tensors φˆrs and φˆ¯rs , in equations (8.3) and (8.4), are obviously of diagonal form and are given by: φîj

¯ φîj

⎛ˆ φ1 ⎝ = 0 0 ⎛¯ φˆ1 ⎜ = ⎝0 0

0 φˆ2 0 0 ¯ φˆ2 0

⎞ 0 0 ⎠ φˆ3 ⎞ 0 ⎟ 0 ⎠ ¯ φˆ3

and the second-order transformation tensors b and c are given by: ⎛ 1 1 1⎞ n1 n2 n3 bir = ⎝ n21 n22 n23 ⎠ n31 n32 n33 ⎛ 1 1 1⎞ m1 m2 m3 cir = ⎝ m21 m22 m23 ⎠ m31 m32 m33

(8.5)

(8.6)

(8.7)

(8.8)

These proper orthogonal transformation tensors require that: bij bkj = cij ckj = δik


(8.9)

216

Damage Mechanics

where δik is the Kronecker delta and the determinants of the matrices [b] and [c] are given by: |b| = |c| = 1

(8.10)

¯ is shown in section The relation between the damage tensors φ and φ 8.4.

8.3

Fourth-Order Anisotropic Damage Effect Tensor

¯ is In a general state of deformation and damage, the effective stress tensor σ related to the Cauchy stress tensor σ by the following linear transformation as was shown in previous chapters (Murakami and Ohno, 1981): σ ¯ij = Mijkl σkl

(8.11)

where M is a fourth-order linear transformation operator called the damage effect tensor. Depending on the form used for M, it is very clear from ¯ is generally nonsymmetric. equation (8.11) that the effective stress tensor σ Using a nonsymmetric effective stress tensor as given by equation (8.11) to formulate a constitutive model will result in the introduction of the Cosserat and micropolar continua. However, the use of such complicated mechanics can be easily avoided if the proper fourth-order linear transformation tensor is formulated in order to symmetrize the effective stress tensor. Such a linear transformation tensor called the damage effect tensor is obtained in the literature (Lee et al., 1986; Cordebois and Sidoroff, 1979) using symmetrization methods. One of the symmetrization methods given by Cordebois and Sidoroff (1979) and Lee et al. (1986) is expressed as follows: σ ¯ij = (δik − φik )−1/2 σkl (δjl − φjl )−1/2

(8.12)

The fourth-order damage effect tensor corresponding to equation (8.12) is defined such that: Mijkl = (δik − φik )−1/2 (δjl − φjl )−1/2

(8.13)

In order to describe the kinematics of damage, the physical meaning of the fourth-order damage effect tensor should be interpreted and not merely given as the symmetrization of the effective stress. In this chapter, the fourth-order damage effect tensor given by equation (8.13) will be used



217

because of its geometrical symmetrization of the effective stress (Cordebois and Sidoroff, 1979). However, it is very difficult to obtain the explicit representation of (δik − φik )−1/2 . The explicit representation of the fourthorder damage effect tensor M using the second-order damage tensor φ is of particular importance in the implementation of the constitutive modeling of damage mechanics. Therefore, the damage effect tensor M of equation (8.13) should be obtained using the coordinate transformation of the principal damage direction coordinate system. Thus, the fourth-order damage effect tensor given by equation (8.13) can be written as follows (Voyiadjis and Park, 1996a,b). ˆ mnpq Mikjl = bmi bnj bpk bql M

(8.14)

ˆ is a fourth-order damage effect tensor with the reference to the where M principal damage direction coordinate system. The fourth-order damage ˆ can be written as follows (Voyiadjis and Park, 1996a,b): effect tensor M ˆ mnpq = a M ˆmp a ˆnq

(8.15)

where the second order tensor ˆ a in the principal damage direction coordinate system is given by: ⎡ ⎢ a ˆmp = (δmp − φˆmp )−1/2 ≡ ⎢ ⎣

√

1 ˆ1 1−φ

o o

√

o

o

1

o

ˆ2 1−φ

o

√1 ˆ3 1−φ

⎤ ⎥ ⎥ ⎦

(8.16)

Substituting equation (8.15) into equation (8.14), one obtains the following relation: Mijkl = bmi bnj bpk bql a ˆmp a ˆnq = aik ajl

(8.17)

Using equation (8.17), a second-order tensor a is defined as follows: ˆmp aik = bmi bpk a

(8.18)

The matrix form of equation (8.18) is given as follows (Voyiadjis and Park, 1995a,b):


218

Damage Mechanics

a][b] [a] = [b]T [ˆ ⎡ b11 b11 b21 b21 b31 b31 b11 b12 b21 b22 b31 b32 √ √ +√ +√ +√ +√ ˆ1 ˆ2 ˆ3 ˆ1 ˆ2 ˆ3 1−φ 1−φ 1−φ 1−φ 1−φ 1−φ ⎢ ⎢ ⎢ b21 b11 b22 b21 b32 b31 b12 b12 b22 b22 b32 b32 √ √ +√ +√ +√ +√ =⎢ ˆ2 ˆ3 ˆ1 ˆ2 ˆ3 ⎢ 1−φˆ1 1−φ 1−φ 1−φ 1−φ 1−φ ⎢ ⎣ b31 b11 b23 b21 b33 b31 b13 b12 b23 b22 b33 b32 √ √ +√ +√ +√ +√ ˆ ˆ ˆ ˆ ˆ ˆ 1−φ1

b11 b13 √ ˆ1 1−φ b12 b13 √ ˆ1 1−φ b13 b13 √ ˆ1 1−φ

8.4

1−φ2

+ + +

b21 b23 √ ˆ2 1−φ b22 b23 √ ˆ2 1−φ b23 b23 √ ˆ2 1−φ

1−φ3

+ + +

b31 b33 √ ˆ3 1−φ b32 b33 √ ˆ3 1−φ b33 b33 √ ˆ3 1−φ

⎤

1−φ1

1−φ2

1−φ3

⎥ ⎥ ⎦

(8.19)

The Kinematics of Damage for Elasto-Plastic Behavior with Finite Strains

A position of a particle in C o at to is denoted by X and can be defined at its corresponding position in C t at t, denoted by x. Furthermore, assuming that the deformation is smooth regardless of damage, one can assume a one-to-one mapping such that: xk = xk (X, t)

(8.20)

Xk = Xk (x, t)

(8.21)

or

The corresponding deformation gradient is expressed as follows: Fij =

∂xi ∂Xj

(8.22)

and the change in the squared length of a material filament dX is used as a measure of deformation such that: (ds)2 − (dS)2 = dxi dxi − dXi dXi = 2εij dXi dXj or


(8.23)

Kinematics of Damage for Finite-Strain Elasto-Plastic Solids (ds)2 − (dS)2 = 2 ij dxi dxj 2

219

(8.24)

2

where (ds) and (dS) are the squared lengths of the material filaments in the deformed with damage configuration C t , and the initial undeformed configuration C o , respectively. ε and are the Lagrangian and Eulerian strain tensors, respectively, and are given by: εij =

1 1 (Fki Fkj − δij ) = (Cij − δij ) 2 2

(8.25)

1 1 −1 −1 −1 (δij − Fki Fkj ) = (δij − Bij ) (8.26) 2 2 where C and B are the right Cauchy-Green and the left Cauchy-Green tensors, respectively. The velocity vector field in the current configuration at time t is given by:

ij =

dxi (8.27) dt The velocity gradient in the current configuration at time t is given by: vi =

Lij =

∂vi ∂xj

(8.28)

−1 = dFik Fkj = Dij + Wij

where dF indicates the material time derivative and where D and W are the rate of deformation (stretching) and the vorticity, respectively. The rate of deformation D is equal to the symmetric part of the velocity gradient L, while the vorticity W is the antisymmetric part of the velocity gradient L such that: Dij =

1 (Lij + Lji ) 2

(8.29)

1 (Lij − Lji ) (8.30) 2 Strain rate measures are obtained by differentiating equations (8.23) and (8.24) such that: Wij =

d [(ds)2 − (dS)2 ] = 2dXi dεij dXj dt = 2dxi Dij dxj = 2dXi Fik Dij Fjm dXm = 2dxi (d ij + ik Lkj + Lik kj )dxj


(8.31)

220

Damage Mechanics

By comparing equations (8.31a) and (8.31c), one obtains the rate of the Lagrangian strain that is the projection of D onto the reference frame as follows: dεij = Fki Dkl Flj

(8.32)

while the deformation rate D is equal to the Cotter-Rivin connected rate of the Eulerian strain as follows: Dij = d ij + ik Lkj + Lik kj

(8.33)

The convected derivative shown in equation (8.33) can also be interpreted as the Lie derivative of the Eulerian Strain (Lubarda and Krajcinovic, 1995).

8.4.1

A Multiplicative Decomposition

A schematic drawing representing the kinematics of elasto-plastic damage deformation is shown in Figure 8.1. In the figure, C o is the initial undeformed configuration of the body which may have initial damage in the material. C t represents the current elasto-plastically deformed and damaged configuration of the body. The configuration of C¯ o represents the initial configuration of the body that is obtained by fictitiously removing the initial damage from the C o configuration. If the initial configuration is undamaged, consequently there is no difference in the configurations C o and C¯ o . The configuration C¯ t is obtained by fictitiously removing the damage from the configuration C t . Configuration C dp is an intermediate configuration upon elastic unloading. In the most general case of large deformation processes, damage may be involved due to void and microcrack development because of external agencies. Although damage at the microlevel is a material discontinuity, damage can be considered as an irreversible deformation process in the framework of continuum damage mechanics. Furthermore, one assumes that upon unloading from the elastoplastic damage state, the elastic part of the deformation can be completely recovered while no additional plastic deformation and damage takes place. Thus, upon unloading the elasto-plastic damage deformed body from the current configuration C t will elastically unload to an intermediate stress free configuration denoted by C dp as shown in Figure 8.1. Although the damage process is an irreversible deformation thermodynamically, however, the deformation due to damage itself can be partially or completely recovered upon unloading due to closure of microcracks or contraction of microvoids. Nevertheless, recovery of damage deformation does not mean the healing of damage. The deformation gradient tensor and the Green deformation tensor of the elasto-plastic damage deformation can be obtained



221

through Path I, Path II, or Path III as shown in Figure 8.1. Consider Path I - the deformation gradient referred to the undeformed configuration C o , is denoted by F and is polarly decomposed into the elastic deformation gradient denoted by Fe and the damage-plastic deformation gradient denoted by Fdp such that:

Fe

Fdp

o

C

C

Ct

dp

Path I: Path II: Path III: Fdo

Fd

Cp Fp

o

Fp

p

C

Fe

C

Ct

FIGURE 8.1 Schematic representation of elasto-plastic damage deformation configurations.(Voyiadjis and Park, 1999)

e dp Fkj Fij = Fik

(8.34)

The elastic deformation gradient is given by: Fije =

∂xi ∂xdp j

(8.35)

The corresponding damage-plastic deformation gradient is given by: Fijdp =

∂xdp i ∂Xj

(8.36)

The right Cauchy-Green deformation tensor C is given by: dp e e dp Cij = Fnk Fki Fnm Fmj


(8.37)

222

Damage Mechanics

The finite deformation damage models by Ju (1989) and Zbib (1993) emphasize that “added flexibility” due to the existence of microcracks or microvoids is already embedded in the deformation gradient implicitly. Murakami (1983) presented the kinematics of damage deformation using the second-order damage tensor. However, the lack of an explicit formulation for the kinematics of finite deformation with damage leads to the failure in obtaining an explicit derivation of the kinematics that directly consider the damage deformation. Although most finite strain elasto-plastic deformation processes involve damage such as microvoids, nucleations and microcracks development due to external agencies, however, only the elastic and plastic deformation processes are considered kinematically due to the complexity in the development of damage deformation. In this chapter, the kinematics of damage will be explicitly characterized based on continuum damage mechanics. The elastic deformation gradient corresponds to elastic stretching and rigid body rotations due to both internal and external constraints. The plastic deformation gradient arises from purely irreversible processes due to dislocations in the material. Damage may by initiated and evolves in both the elastic and plastic deformation processes. Particularly, damage in the elastic deformation state is termed elastic damage, which is the case for most brittle materials, while damage in the plastic deformation state is termed plastic damage which is mainly for ductile materials. Additional deformation due to damage consists of damage itself with additional deformation due to elastic and plastic stiffness. In this chapter, kinematics of damage deformation is completely described for both damage and the coupling of damage with elasto-plastic deformation. The total Lagrangian strain tensor is expressed as follows: 1 dp dp 1 dp e e dp (F F − δij ) + Fmi (Fkm Fkn − δmn )Fnj 2 ki kj 2 dp e dp = εdp ij + Fmi mn Fnj

εij =

(8.38)

e = εdp ij + εij

where εdp and εe are the Lagrangian damage-plastic strain tensor and the Lagrangian elastic strain tensor, respectively, measured with respect to the reference configuration C o . e is the Lagrangian elastic strain tensor measured with respect to the intermediate configuration C dp . Similarly, the Eulerian strains corresponding to deformation gradients Fe and Fdp are given by: edp ij = eeij =


1 dp−1 dp−1 (δij − Fki Fkj ) 2

(8.39)

1 e−1 e−1 (δij − Fki Fkj ) 2

(8.40)


223

The Eulerian strain tensor can be expressed as follows: −1

−1

e e

ij = eij + Fki edp km Fmj

=

eij

+

(8.41)

dp ij

The strain edp is referred to the intermediate configuration C dp , while the strains , e , and dp are defined relative to the current configuration as a reference. The relationship between the Lagrangian and Eulerian strains is obtained directly in the form: εij = Fki kl Flj

(8.42)

The change in the squared length of a material filament deformed elastically from C t to C dp is given by: dp (ds)2 − (dsdp )2 = dxi dxi − dxdp i dxi = 2dXi εeij dXj

(8.43)

However, the change in the squared length of a material filament due to damage and plastic deformation from C dp to C o is given by: (dsdp )2 − (dS)2 = 2dXi εdp ij dXj

(8.44)

The kinematics of finite strain elasto-plastic deformation including damage is completely described in Path I. In order to describe the kinematics of damage and plastic deformation, the deformation gradient given by equation (8.34) may be further decomposed into: p e d Fij = Fik Fkm Fmj

(8.45)

However, it is very difficult to characterize physically only the kinematics of deformation due to damage in spite of its obvious physical phenomena. The damage, however, may be defined through the effective stress concept. Similarly, the kinematics of damage can be described using the kinematic configuration. Considering Path II, the deformation gradient can be alternatively expressed as follows: d ¯ e ¯ p ¯ do Fkm Fmn Fnj Fij = F¯ik

(8.46)

¯d

where F is the fictitious damage deformation gradient from configuration C¯ t to C t and is given by: ∂xi F¯ijd = ∂x ¯j


(8.47)

224

Damage Mechanics

The elastic deformation gradient in the effective configuration is given by: ∂x ¯i F¯ije = ∂x ¯pj

(8.48)

The corresponding plastic deformation gradient in the effective configuration is given by: ∂x ¯p F¯ijp = ¯i ∂ Xj

(8.49)

while the fictitious initial damage deformation gradient from configuration C¯ o to C o is given by: ¯i ∂X F¯ijdo = ∂Xj

(8.50)

Similar to Path I, the right Cauchy Green deformation tensor, C, is given by: do ¯ p ¯ e ¯ d ¯ d ¯ e ¯ p ¯ do Cij = F¯mk Fkp Fpq Fqi Fmn Fnr Frs Fsj

(8.51)

The Lagrangian damage strain tensor measured with respect to the fictitious configuration C¯ t is given by: 1 ¯d ¯d (8.52) (F F − δij ) 2 ki kj and the corresponding Lagrangian effective elastic strain tensor measured with respect to the fictitious configuration C¯ p is given by:

¯dij =

1 ¯e ¯e (F F − δij ) (8.53) 2 ki kj The Lagrangian effective plastic strain tensor measured with respect to the fictitious undamaged initial configuration C¯ o is given by:

¯e =

1 ¯p ¯p (F F − δij ) (8.54) 2 ki kj The total Lagrangian strain tensor is therefore expressed as follows:

¯pij =

1 ¯ do ¯ do 1 do ¯ p ¯ p do (F F − δij ) + F¯mi (Fkm Fkn − δmn )F¯nj 2 ki kj 2 1 do ¯ p ¯ e ¯ e p ¯ do Frn (Fqr Fqs − δrs )F¯sm Fmj + F¯ni 2 1 do ¯ p ¯ e ¯ d ¯ d e ¯ p ¯ do Fnw Frn (Fqr Fqs − δrs )F¯sm Fmk Fkj + F¯wi 2

εij =


(8.55)


225

The Lagrangian initial damage strain tensor measured with respect to the reference configuration C o is denoted by: 1 ¯ do ¯ do (F F − δij ) (8.56) 2 ki kj The Lagrangian plastic strain tensor measured with respect to the reference configuration C o is denoted by: ε¯do ij =

do p ¯ do ε¯pij = F¯ki ¯ km Fmj

(8.57)

One now defines the Lagrangian elastic strain tensor measured with respect to the reference configuration C o as follows: do ¯ p e ¯ p ¯ do ε¯eij = F¯ni Fnk ¯km Fmr Frj

(8.58)

and the corresponding Lagrangian damage strain tensor measured with respect to the reference configuration C o is given by: do ¯ p ¯ e d ¯ e ¯ p ¯ do Fwn Fnk ¯ km Fmr Frs Fsj ε¯dij = F¯wi

(8.59)

The total Lagrangian strain is now given as follows through the additive decomposition of the corresponding strains: ¯pij + ε¯eij + ε¯dij εij = ε¯do ij + ε

(8.60)

The change in the squared length of a material filament deformed due to fictitiously removing of damage from C t to C¯ t is given by: ¯ 2 = dxi dxi − d¯ (ds)2 − (ds) xi d¯ xi = 2dXi ε¯dij dXj

(8.61)

The change in the squared length of a material filament deformed elastically from C¯ t to C¯ p is given by: ¯ 2 − (ds ¯ p )2 = d¯ (ds) xi d¯ xi − d¯ xpi d¯ xpi

(8.62)

= 2dXi ε¯eij dXj The change in the squared length of a material filament deformed plastically from C¯ o to C¯ p is then given by: p

¯ 2 = d¯ ¯ )2 − (dS) ¯ i dX ¯i xpi d¯ xpi − dX (ds =


2¯ εpij dXi dXj

(8.63)

226

Damage Mechanics

while the change in the squared length of a material filament deformed due to fictitious removing of the initial damage from C¯ o to C o is given by: ¯ 2 − (ds)2 = dX ¯ i dX ¯ i − dXi dXi (ds) = 2dXi ε¯do ij dXj

(8.64)

Finally, Path III gives the deformation gradient as follows: d ˜ p ¯ do Fij = File F˜lm Fmn Fnj

(8.65)

˜ d is the fictitious damage deformation gradient from configuration where F p ˜ C to C dp and is given by: ∂xdp i F˜ijd = (8.66) ∂x ˜p and the corresponding plastic deformation gradient in the effective configuration is given by: ∂x ˜pi F˜ijp = ∂Xj

(8.67)

Similar to Path II, the Right Cauchy Green deformation tensor C is given by: do ˜ p ˜ d e e ˜ d ˜ p ¯ do Fkp Fpq Fqi Cij = F¯mk Fmn Fnr Frs Fsj

(8.68)

The Lagrangian damage strain tensor measured with respect to the fictitious intermediate configuration C˜ p is given by: 1 ˜d ˜d (F F − δij ) 2 ki kj The total Lagrangian strain tensor is expressed as follows:

˜dij =

1 ¯ do ¯ do 1 do ˜ p ˜ p do (Fki Fkj − δij ) + F¯mi (Fkm Fkn − δmn )F¯nj 2 2 1 do ˜ p ˜ d ˜ d p ¯ do Frn (Fqr Fqs − δrs )F¯sm Fmj + F¯ni 2 1 do ˜ p ˜ d e e d ˜ p ¯ do Fnw Frn (Fqr Fmk Fkj + F¯wi Fqs − δrs )F˜sm 2

(8.69)

ε¯ij =

(8.70)

The Lagrangian damage strain tensor measured with respect to the reference configuration C o is denoted by: do ˜ p p ¯ do Fmk ˜dmn Fñq Fqj ε¯dij = F¯ki


(8.71)


227

The Lagrangian elastic strain tensor measured with respect to the reference configuration C o is denoted by: p ˜d d ˜ p ¯ do Fmk emn Fñq Fqr Frj εeij = F¯lido F˜kl

(8.72)

The corresponding total Lagrangian strain is now given by: ¯pij + ε¯dij + ε¯eij εij = ε¯do ij + ε

(8.73)

The change in the squared length of a material filament deformed to fictitious removal of damage from C dp to C˜ p is given by: dp (dsdp )2 − (d˜ sp )2 = dxdp xpi d˜ xpi i dxi − d˜ = 2dxi ε˜dij dXj

(8.74)

The change in the squared length of a material filament deformed plastically from C¯ o to C˜ p is then given by: ¯ 2 = d˜ ¯ i dX ¯i (d˜ sp )2 − (dS) xpi d˜ xpi − dX p = 2dxi ε˜ij dXj

(8.75)

The total Lagrangian strain tensors obtained by considering the three paths are given by equations (8.38), (8.60), and (8.73). From the equivalence of these total strains, one obtains the explicit presentations of the kinematics of damage as follows. With the assumption of the equivalence between the elastic strain tensors given by equations (8.38) and (8.73), the damage-plastic deformation gradient given by equation (8.36) and the Lagrangian damage plastic strain tensor can be expressed as follows: do ˜ p ˜ d Fkl Flj Fijdp = F¯ik

(8.76)

¯do ˜pij + ε˜dij εdp ij + ε ij = ε

(8.77)

and

Furthermore, one obtains the following expression from equations (8.60) and (8.73) as follows: ε¯eij + ε¯dij = ε˜dij + εeij

(8.78)

which concludes that C˜ p and C¯ p are the same. Substituting equations (8.59), (8.71), and (8.72) into equation (8.78), one obtains the effective Lagrangian elastic tensor as follows:


228

Damage Mechanics do ¯ p e d ¯e d ¯ p ¯ do Fmk (˜

dmn − F¯qm

¯qr Frn + F˜qm eqr F˜rn )Fns Fsj ε¯eij = F¯ki

(8.79)

Using equations (8.58) and (8.79), one can now express ¯ as follows: e d e d e d

¯eij = ˜dij − F¯mi

¯mn F¯nj + F˜mi

mn Fñj

(8.80)

This expression gives a general relation of the effective elastic strain for finite strains of elasto-plastic damage deformation. For the special case when one assumes that e d e

¯mn F¯nj =0

˜d − F¯mi

(8.81)

equation (8.80) can be reduced to the following expression: d e ˜d

¯eij = F˜ki

kl Flj

(8.82)

This relation is similar to that obtained without the consideration of the kinematics of damage and only utilizing the hypothesis of elastic energy equivalence. However, equation (8.82) for the case of finite strains is given by relation (8.80) which cannot be obtained through the hypothesis of elastic energy equivalence. Equation (8.81) may be valid only for some special case of the small strain theory.

8.4.2

Fictitious Damage Deformation Gradients

The two fictitious deformation gradients given by equations (8.47) and (8.66) may be used to define the damage tensor in order to describe the damage behavior of solids. Since the fictitious effective deformed configuration denoted by C¯ t is obtained by removing the damages from the real deformed configuration denoted by C t , therefore, the differential volume ¯ t is obtained as of the fictitious effective deformed volumes denoted by dΩ follows (Onat, 1986): ¯ t = dΩt − dΩd dΩ = (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 )

(8.83) dΩt

or ¯t dΩt = J¯d dΩ d

(8.84) t

¯d

where Ω is the volume of damage in the configuration C and J is termed the Jacobian of the damage deformation which is the determinant of the fictitious damage deformation gradient. Thus, the Jacobian of the damage deformation can be written as follows:



J¯d = |F¯ijd |

229

(8.85) 1

= (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 ) The determinant of the matrix [a] in equation (8.19) is given by: a||b| |a| = |b|T |ˆ = |ˆ a|

(8.86)

1 = (1 − φˆ1 )(1 − φˆ2 )(1 − φˆ3 ) Thus, one assumes the following relation without loss of generality: F¯ijd = (δij − φij )−1/2

(8.87)

Although the identity is established between J¯d and |a|, however, this is not sufficient to demonstrate the validity of equation (8.87). This relation is assumed here based on the physics of the geometrically symmetrized effective stress concept (Onat, 1986). Similarly, the fictitious damage de˜ d can be written as follows: formation gradient F F˜ijd = (δij − φij )−1/2

(8.88)

¯ = x ˜ based on equation (8.78), the relations Finally, assuming that x ¯ are given by: ¯ d , and φ and φ ˜ d and F between F

8.4.3

e ¯ d e− 1 Fkl Flj F˜ijd = Fki

(8.89)

− e φ¯ij = Fki φkl Flje 1

(8.90)

An Additive Decomposition

The kinematics of finite deformation is described here based on the polar decomposition by considering three paths as indicated in the previous section. In order to proceed further, one assumes a homogeneous state of deformation such that the completely unloaded stress-free configuration C dp has opened cracks and micro-cavities. Furthermore, one assumes that these cracks and micro-cavities can be completely closed by subjecting them to certain additional stress. The configuration that is subjected to the additional stresses is denoted by C p and it is assumed that this configuration


230

Damage Mechanics

has only deformed plastically. The additional stress which can close all micro-cracks and micro-cavities is assumed as follows: ∗ = σij − σ ¯ij σij

(8.91) o

If no initial damage is assumed in the configuration C , it can be assumed such that C p = C˜ p . The total displacement vector u(X, t) can be decomposed in the Cartesian reference frame in the absence of rigid body displacement such that: ui = uei + udi + upi

(8.92)

ui = xi − Xi

(8.93)

uei = xi − xdi

(8.94)

udi = xdi − xpi

(8.95)

upi = xpi − Xi d

(8.96) dp

where x is a point in the intermediate unloaded configuration C and xp is a point in the configuration C˜ p . Recalling that u = x − X and using the notation ui,j = ∂xi /∂Xj , the corresponding total Lagrangian strain tensor ε is given by equation (8.25) can be written in the usual form as follows: 1 (ui,j + uj,i + uk,i uk,j ) 2 Substituting equation (8.92) into equation (8.97), one obtains: εij =

pe pd εij = pij + dij + eij + de ij + ij + ij

(8.97)

(8.98)

where p termed the pure plastic strain is given by:

pij =

1 p (u + upj,i + upk,i upk,j ) 2 i,j

(8.99)

d termed the pure damage strain is given by: 1 d (u + udj,i + udk,i udk,j ) 2 i,j e termed the pure elastic strain is given by:

dij =

eij =


1 e (u + uej,i + uek,i uek,j ) 2 i,j

(8.100)

(8.101)


231

de termed the coupled elastic-damage strain is given by: 1 e d (u u + udk,i uek,j ) 2 k,i k,j termed the coupled elastic-plastic strain is given by:

de ij =

pe

pe ij =

1 e p (u u + upk,i uek,j ) 2 k,i k,j

(8.102)

(8.103)

and pd termed the coupled plastic-damage strain is given by: 1 p d (u u + udk,i upk,j ) 2 k,i k,j One defines the Lagrangian elastic strain as follows:

pd ij =

pe εeij = eij + de ij + ij

(8.104)

(8.105)

the Lagrangian damage strain as follows: εdij = dij

(8.106)

and the Lagrangian plastic strain as follows: εpij = pij + pd ij

(8.107)

The coupled term of elastic-damage and plastic-damage strains are linked, respectively, with the elastic and plastic strains since they directly influence the stresses acting on the body. Consequently, the total Lagrangian strain can be written as follows: εij = εpij + εdij + εeij

(8.108)

The differential displacement is given by: − xti dui = xt+dt i

(8.109)

Then, the corresponding differential total displacement can be decomposed into an elastic, plastic, and damage parts as follows: dui = duei + dudi + dupi

(8.110)

Evidently, one obtains the following decomposition of the velocity tensor field v(x, t): vi (xi , t) = vie (xi , t) + vid (xi , t) + vip (xi , t) e

(8.111)

where v is the velocity vector field due to elastic stretching and rigid body rotations, vd is the velocity vector field due to the damage process, and


232

Damage Mechanics

vp is the velocity vector field arising from the plastic deformations due to dislocation motion. The gradient of the frame x is given by the following relation:

8.5

Lij = Leij + Ldij + Lpij

(8.112)

p e d + Dij + Dij Dij = Dij

(8.113)

Wij = Wije + Wijd + Wijp

(8.114)

Irreversible Thermodynamics

The finite elasto-plastic deformation behavior with damage can be viewed within the framework of thermodynamics with internal state variables. The Helmholtz free energy per unit mass in an isothermal deformation process at the current state of the deformation and material damage is assumed as follows: Ψ=ψ+γ

(8.115)

where ψ is the strain energy which is a purely reversible stored energy, while γ is the energy associated with specific microstructural changes produced by damage and plastic yielding. Conceptionally, the energy γ is assumed to be an irreversible energy. In general, an explicit presentation of the energy γ and its rate dγ is limited by the complexities of the internal microstructural changes, however, only two internal variables which are associated with damage and plastic hardening, respectively, are considered in this work. For the sake of a schematic description of the above stated concepts, the uniaxial stress-strain curves shown in Figure 8.2 are used. In Figure 8.2, ¯ is the initial undamaged Young’s modulus, E is the damaged Young’s E modulus, S is the second Piola-Kirchhoff stress, and ε is the Lagrangian strain. Even though these notations are for the case of uniaxial state, they can be used in indicial tensor notation in the equations below without loss of generality. Referring to the solid curve in Figure 8.2, the total Lagrangian strain tensor ε is given by: εij = εpij + εeij + εdij


(8.116)


233

elasto-plastic-damage S-ε curve S

elasto-plastic S-ε curve

S

E E E E

εp

ε

εe εE εd

εd

''

'

εe

ε

d

FIGURE 8.2 Schematic representation of elasto-plastic damage stress-strain curves for the uniaxial state of the stress.(Voyiadjis and Park, 1999)

where εp is the plastic strain tensor, εe is the elastic strain tensor, and εd is the additional strain tensor due to damage. Comparing equations (8.38) and (8.116), one notes that: p d εdp ij = εij + εij


(8.117)

234

Damage Mechanics

Furthermore, the additional strain tensor due to damage can be decomposed as follows:

εdij = εdij + εdij

(8.118)

where εdij is the irrecoverable damage strain tensor due to lack of closure of the microcracks and microvoids during unloading, while εdij is the elastic damage strain tensor due to the reduction of the elastic stiffness tensor. Thus, the purely reversible strain tensor, εE , due to unloading can be obtained by:

e d εE ij = εij + εij

(8.119)

The strain energy ψ which is shown as the shaded triangular area in Figure 8.2 is assumed as follows: ψ=

1 E ε Eijkl εE kl 2ρ ij

(8.120)

where ρ is the specific density. Furthermore, this strain energy can be decomposed into the elastic strain energy ψ e and the damage strain energy ψ d as follows: ψ = ψe + ψd

(8.121)

e

The elastic strain energy ψ is given by: ψe =

1 e ¯ ε Eijkl εekl 2ρ ij

(8.122)

and the corresponding damage strain energy ψ d is given by: ψd =

1 E 1 e ¯ εij Eijkl εE ε Eijkl εekl kl − 2ρ 2ρ ij

(8.123)

¯ and E are the initial undamaged elastic stiffness and the damaged where E elastic stiffness, respectively. These stiffnesses are defined such that: ¯ijkl = E

∂2Ψ ∂εeij ∂εekl

(8.124)

Eijkl =

∂2Ψ E ∂εE ij ∂εkl

(8.125)

The damaged elastic stiffness in the case of finite deformation is given by Park and Voyiadjis (1998) as follows: ¯klpq Nprqs Eijrs = Nikjl E


(8.126)


235

where −1 Nikjl = Mikjl

=

(8.127)

−1 a−1 ik ajl

The elastic damage stiffness given by equation (8.126) is symmetric. This is in line with the classic sense of continuum mechanics which is violated by using the hypothesis of strain equivalence. Using the similar relation between the Lagrangian and the Eulerian strain tensors given by equation (8.42), the corresponding strain energy given by equation (8.120) can be written as follows: 1 E

Fmi Fnj Eijkl Frk Fsl E rs 2ρ mn 1 E

Λmnrs E = rs 2ρ mn

ψ=

(8.128)

where E is the Eulerian strain corresponding to the Lagrangian strain shown in equation (8.119), and Λ is termed the Eulerian elastic stiffness which is given by: Λmnrs = Fmi Fnj Eijkl Frk Fsl

(8.129)

The second Piola-Kirchhoff stress tensor S is defined as follows:

Sij = ρ

∂ψ ∂εE ij

=ρ

∂ψ e ∂εeij

(8.130)

The second Piola-Kirchhoff stress tensor S is related to the Cauchy stress tenor σ as follows: −1 σkm Fjm Sij = JFik

(8.131)

The Kirchhoff stress tensor T is related to the Cauchy stress tensor σ as follows: Tij = Jσij

(8.132)

The rate of Helmholtz free energy is then given as follows: dΨ = dψ + dγ


(8.133)

236

Damage Mechanics

where dγ is the rate of γ associated with the two neighboring constrained equilibrium states with two different sets of internal variables φ and X. Using equation (8.120) or (8.121), the rate form of the strain energy can ¯ = 0: be given as follows since dE ρdψ =

dρ E 1 E E E dEijkl εE ε Eijkl εE ij εkl + Eijkl εij dεkl − kl 2 2ρ ij

(8.134)

¯ijkl εekl − dρ εeij E ¯ijkl εekl ρdψ e = dεeij E 2ρ

(8.135)

or

and 1 E dρ E E E e ¯ e e ¯ e (ε Eijkl εE ρdψ d = dεE ij Eijkl εkl + εij dEijkl εkl −dεij Eijkl εkl − kl −εij Eijkl εkl ) 2 2ρ ij (8.136) If the deformation process is assumed to be isothermal with negligible temperature nonuniformities, the rate of the Helmholtz free energy can be written using the first law of thermodynamics (balance of energy) as follows: dΨ = Tij Dij − T η

(8.137)

where T is the temperature and η is the irreversible entropy production rate. The product T η represents the energy dissipation rate associated with both the damage and plastic deformation processes. The energy of the dissipation rate is given as follows:

T η = Sij dεdij + Sij dεpij − dγ

(8.138)

The first two terms on the right-hand side of the equation (8.138) represent a macroscopically nonrecoverable rate of work expanded on damage and plastic processes, respectively. Furthermore, the rate of the additional strain tensor due to damage is given by:

dεdij = dεdij + dεdij

(8.139)

If we assume that the fraction of the additional strain tensor can be recovered during unloading, then the elastic damage tensor due to the reduction of the elastic stiffness is given by:

dεdij = cdεdij


(8.140)


237

where c is a fraction which ranges from 0 to 1. Then, the permanent damage strain due to lack of closure of microcracks and microcavities is given by:

dεdij = (1 − c)dεdij

(8.141)

Thus, the energy of the dissipation rate given by equation (8.138) can be written as follows:

T η = (1 − c)Sij dεdij + Sij dεpij − dγ = (1 −

d c)Tij Dij

+

p Tij Dij

(8.142)

− dγ

The rate of energy associated with a specific microstructural change due to both the damage and the plastic processes can be decomposed as follows: dγ = dγ d + dγ p

(8.143)

ρdγ d = Yij dφij

(8.144)

ρdγ p = Aij dXij

(8.145)

where one defines that

and

where Y and A are the general forces conjugated by damage and plastic yielding, respectively. They are defined as:

Yij = ρ

∂Ψ ∂φij

∂ψ ed ∂γ +ρ ∂φij ∂φij ∂Ψ Aij = ρ ∂Xij

(8.146)

=ρ

(8.147)

In view of equation (8.142), one notes that it is equivalent to the work by Lubarda and Krajcinvic (1995) when (1 − c) = 12 . A schematic representation of the elastic, damage, and plastic strain rates, and the total rate of work Sij d ij is shown on the uniaxial stress-strain curve in Figure 8.3.


238

8.6

Damage Mechanics

Constitutive Equation for Finite Elasto-Plastic Deformation with Damage Behavior

The kinematics and the thermodynamics discussed in the previous sections provide the basis for a finite deformation elasto-plasticity. In this section, the basic structure of the constitutive equations is reviewed based on the generalized Hooke’s law, originally obtained for small elastic strains such that the second Piola-Kirchhoff stress tensor S is the gradient of free energy Ψ with respect to the Lagrangian elastic strain tensor εE given by equation (8.130). Referring to Figure 8.2, one obtains the following relation when generalized to the three dimensional state of stress and strain: ¯ijkl (εkl − εp − εd ) Sij = E kl kl ¯ijkl εekl =E =

Eijkl (εekl

+

= Eijkl (εkl −

εdkl ) εdkl − εpkl )

(8.148a) (8.148b) (8.148c) (8.148d)

From the incremental analysis, one obtains the following rate form of the constitutive equation by differentiating equation (8.148a): ¯ijkl (dεkl − dεp − dεdkl ) dSij = E kl

(8.149)

Consequently the constitutive equation of the elasto-plastic damage behavior can be writen as follows: Dp dSij = Eijkl dεkl

(8.150)

where EDp is the damage elasto-plastic stiffness tensor and is expressed as follows: Dp ¯ikjl − E p − E d Eijkl =E ikjl ikjl

(8.151)

where Ep is the plastic stiffness and Ed is the damage stiffness. Both Ep and Ed are the reduction in stiffness due to the plastic and damage deteriorations, respectively. The plastic stiffness and the damage stiffness can be obtained by using the flow rule and damage evolution law, respectively. By assuming that the reference state coincides with the current configuration, the second Piola-Kirchhoff stress rate dS can be replaced by the corotational rate of the Cauchy stress tensor σ and the rate of the Lagrangian strain tensor d by the deformation rate D as follows:



239

S

''

'

dεd dεp

dεd dεe

S dS S- dS

E

E E

E

E

dεp

''

dεd

dεE

ε

ε

FIGURE 8.3 Schematic representation of elasto-plastic damage strain increments in the case of a uniaxial stress-strain curve.(Voyiadjis and Park, 1999)

◦

Dp σij = Eijkl Dkl

(8.152)

The corotational rate of the Cauchy stress tensor σ is related to the rate of the Cauchy stress tensor dσ as follows: ◦

∗ ∗ σij = dσij − Wik σkj + σik Wkj

where


(8.153)

240

Damage Mechanics W∗ = W − Wp − Wd

(8.154)

Problems 8.1. Derive the matrix in equation (8.19) explicitly. 8.2. Derive equation (8.55) explicitly. 8.3. Derive equation (8.70) explicitly. 8.4. Derive equations (8.128) and (8.129) explicitly. 8.5. Derive equations (8.134), (8.135), and (8.136) explicitly. 8.6. Derive an explicit formula for the damage elasto-plastic stiffness tenDp appearing in the equation (8.150). sor Eijkl


References

Allen, D. H., Harris, C. E. and Groves, S. E. (1987) A Thermomechanical Constitutive Theory for Elastic Composites with Distributed Damage-I. Theoretical Development, International Journal of Solids and Structures, Vol. 23, No. 9, pp. 1301-1318. Armstrong, P. J. and Frederick, C. O. (1966) A mathematical representation of the multiaxial Bauschinger effect, CEGB Report RD/B/N/731, Berkeley Nuclear Laboratories. Asaro, R. (1983) Micromechanics of Crystals and Polycrystals, Advances in Applied Mechanics, Vol. 23, pp. 1-115. Bammann, D. and Aifantis, E. (1989) A Damage Model for Ductile Metals, Nuclear Engineering and Design, Vol. 116, pp. 13-32. Barsoum, R. S. (1976) On the Use of Isoparametric Finite Elements in Linear Fracture Mechanics, International Journal of Numerical Method Engineering, Vol. 10, pp. 25 37. Betten, J. (1981) Damage Tensors in Continuum Mechanics, J. Mecanique Theorique et Appliquees, Vol. 2, pp. 13-32 (Presented at Euromech Colloqium 147 on Damage Mechanics, Paris-VI, Cachan, 22 September). Betten, J. (1982) Representation of Constitutive Equations in Creep Mechanics of Isotropic and Anisotropic Materials, Presentation at IUTAM, 3rd Symposium on Creep in Structures, Leicester, September 8-12, 1980, published in Proceedings, Creep in Structures, edited by A. R. S. Pointer, Springer-Verlag, Berlin, pp. 179-201. Betten, J. (1983) Damage Tensors in Continuum Mechanics, Journal de Machanique Theorique et Appliquee, Vol 2, No. 1, pp. 13-32. Betten, J. (1986) Applications of Tensor Functions to the Formulation of Constitutive Equations Involving Damage and Initial Anisotropy, Engineering Fracture Mechanics, Vol. 25, Nos. 5/6, pp. 573-584. Boyd, J. G., Costanzo, F. and Allen, D. H. (1983) A Micromechanics Approach for Constructing Locally Averaged Damage Dependent Constitutive Equations in Inelastic Composites, International Journal of Damage Mechanics, Vol. 2, pp. 209-228.


241

242

Damage Mechanics

Chaboche, J. L. (1974) Une Loi Differentielle d’Endommagement de Fatigue avec Cumulation Nonlineare, Rev. Francais Mecanique, No. 50-51 (in French). Chaboche, J. L. (1977) Sur l’utilisation des variables d’etat interne pour la description du comportement viscoplastique et de la rupture par endommagement, In Symposium Franco-polonais de Rheologie et Mecanique, Cracovie. Chaboche, J. L. (1979) Le concept de contrainte effective applique a l’ elasticite et a la viscoplasticite en presence d’un endommagement anisotrope, In Colooque Euromech 115, Villard de Lans. Chaboche, J. (1981) Continuous Damage Mechanics: A Tool to Describe Phenomena Before Crack Initiation, Nuclear Engineering and Design, Vol. 64, pp. 233-247. Chaboche, J. (1988a) Continuum Damage Mechanics: Part I - General Concepts, Journal of Applied Mechanics, ASME, Vol. 55, pp. 59-64. Chaboche, J. (1988b) Continuum Damage Mechanics: Part II - Damage Growth, Crack Initiation, and Crack Growth, Journal of Applied Mechanics, ASME, Vol. 55, pp. 65-72. Chaboche, J. and Lesne, P. (1988) A Nonlinear Continuous Fatigue Damage Model, Fatigue and Fracture of Engineering Materials and Structures, Vol. 11, No. 1, pp. 1-17. Chaboche, J. L. (1989) Constitutive equations for cyclic plasticity and cyclic viscoplasticity, International Journal of Plasticity Vol. 5, pp. 247302. Chaboche, J. L. (1991) On some modifications of kinematic hardening to improve the description of ratchetting effects, International Journal of Plasticity Vol. 7, pp. 661-678. Chaboche, J. (1993) Cyclic Viscoplastic Equations: Part I - Thermodynamically Consistent Formulation, ASME Journal of Applied Mechanics, Vol. 60, pp. 813-821. Chow, C. and Lu, T. (1989) On Evolution Laws of Anisotropic Damage, Engineering Fracture Mechanics, Vol. 34, No. 3, pp. 679-701. Chow, C. and Wang, J. (1987) An Anisotropic Theory of Continuum Damage Mechanics for Ductile Fracture, Engineering Fracture Mechanics, Vol. 27, pp. 547-558. Chow, C. and Wang, J. (1987) An Anisotropic Theory of Elasticity for Continuum Damage Mechanics, International Journal of Fracture, Vol. 33, pp. 3-16.


References

243

Chow, C. and Wang, J. (1988a) Ductile Fracture Characterization with an Anisotropic Continuum Damage Theory, Engineering Fracture Mechanics, Vol. 30, pp. 547-563. Chow, C. and Wang, J. (1988b) A Finite Element Analysis of Continuum Damage Mechanics for Ductile Fracture, International Journal of Fracture, Vol. 38, pp. 83-102. Chow, C. L. and Wei, Y. (1991) A Damage Mechanics Model of Fatigue Crack Initiation in Notched Plates, Theoretical and Applied Fracture Mechanics, Vol. 16, pp. 123-133. Chrzanowski, M. (1973) The Description of Metallic Creep in the Light of Damage Hypothesis and Strain Hardening, Diss. hab. Politechnika Krakowska. Chung, T. (1996) Applied Continuum Mechanics, Cambridge University Press, United Kingdom. Cordebois, J. P. (1983) Criteres d’ Instabilite Plastiques et Endommagement Ductile en Grandes Deformations, These de Doctorat, Presente a l’Universite Pierre et Marie Curie. Cordebois, J. and Sidoroff, F. (1979) Damage Induced Elastic Anisotropy, Colloque Euromech, 115, Villard de Lans. Cordebois, J. P. and Sidoroff, F. (1979) Damage Induced Elastic Anisotropy, In J. P. Boehler, editor, Mechanical Behavior of Anisotropic Solids, Colloque Euromech 115, Villard-deLans, June 19-22, pp. 761-774, Martinus Nijhoff Publishers. Cordebois, J. and Sidoroff, F. (1982) Anisotropic Damage in Elasticity and Plasticity, J. Mech. Theor. Appl. (Special Edition), pp. 45-60 (in French). Corless, R. (1995) Essential Maple: An Introduction for Scientific Programmers. Springer-Verlag, Germany. Cornil, J. and Testud, P. (2001) An Introduction to Maple V, SpringerVerlag, Germany. Dafalias, Y. F. (1981) The concept and application of the bounding surface in plasticity theory, Physical Nonlinearities in Structural Analysis, (Hult, J., Lamaitre, J., ed.), IUTAM Symposium, Senlis, France Springer Verlag, pp. 56-63. Dafalias, Y. (1983) Corotational Rates for Kinematic Hardening at Large Plastic Deformations, Journal of Applied Mechanics, ASME, Vol. 50, pp. 561-565. Doghri, I. (1988) Fully Implicit Integration and Consistent Tangent Modules in Elasto-Plasticity, Mechanics of Solid Materials, Vol. 55, pp. 59-64.


244

Damage Mechanics

Drucker, H. (1948) A More Fundamental Approach to Plastic Stress-Strain Relations, Proceedings of the First U.S. National Congress in Applied Mechanics, ASME, New York, pp. 487-491. Drucker, H. (1959) A Definition of Stable Inelastic Material, Journal of Applied Mechanics, Transactions ASME, Vol. 26, p 101. Eisenburg, M. and Chen, C. (1984) The Anisotropic Deformation of Yield Surfaces, ASME Journal of Engineering Material Technology, Vol. 106, pp. 355-360. Goel, R. P. (1975) On the Creep Rupture of a Tube and a Sphere, J. Applied Mechanics, September, Transactions of the ASME, pp. 625-629. Hayhurst, D. R., Trampczynski, W. A. and Leckie, F. A. (1980) Creep Rupture under Non-Proportional Loading, Acta Metallurgica, Vol. 28, pp. 1171-1183. Eringen, A. (1980) Mechanics of Continua, Krieger, New York, USA. Freed, A., Chaboche, J., and Walker, K. (1991) A Viscoplastic Theory of with Thermodynamic Consideration, Acta Mechanica, Vol. 90, pp. 219241. Fung, Y. (1965) Foundations of Solid Mechanics, Prentice Hall, New Jersey, USA. Fung, Y. (1994) A First Course in Continuum Mechanics, Third Edition, Prentice Hall, New Jersey, USA. Green, A. and Zerna, W. (1968) Theoretical Elasticity, Second Edition, Dover, New York, USA. Gurson, A. (1977) Continuum Theory of Ductile Rupture by Void Nucleation and Growth - Part I: Yield Criteria and Flow Rules for Porous Ductile Media, Journal of Engineering Materials and Technology, Vol. 99, No. 2, pp. 2-15. Hayhurst, D. (1972) Creep Rupture Under Multiaxial States of Stress, Journal of the Mechanical and Physics of Solids, Vol. 20, pp. 381-390. Heck, A. (1996) Introduction to Maple, Second Edition, Springer-Verlag, Germany. Henshell, R. D. and Shaw, K. G. (1975) Crack Tip Finite Elements are Unnecessary, International Journal of Numerical Method Engineering, Vol. 9, pp. 495-507. Hjelmstad, K. (1997) Fundamentals of Structural Mechanics, Prentice Hall, New Jersey, USA. Hori, H. and Nemat-Nasser, S. (1983) Overall Moduli of Solids with Microcracks: Load-Induced Anisotropy, Journal of Mechanics and Physics of Solids, Vol. 31, pp. 155-171.


References

245

Hult, J. (1974) Creep in Continua and Structures, in Topics in Applied Continuum Mechanics (Edited by Zeman and Ziegler), pp. 137, Springer, N.Y. Hult, J. (1979) CDM: Capabilities, Limitations, and Promises in Mechanisms of Deformation and Fracture, Edited by K. Easterling, Pergamon Press, Oxford, pp. 233-247. Ilyushin, A. A. (1954) on relationship between stress and small strain in continuum mechanics, (in, Russian) Prik. Mate. Mech. Vol. 18, pp. 641-666. Johnson, A. E. (1960) Complex-Stress Creep of Metals, Metallurgical Reviews, Vol. 5, No. 20, pp. 447-506. Johnson, G. and Bammann, D. (1984) A Discussion of Stress Rates in Finite Deformation Problems, International Journal of Solids and Structures, Vol. 20, No. 8, pp. 725-737. Ju, J. (1989) Energy Based Coupled Elasto-plastic Damage Theories: Constitutive Modeling and Computational Aspects, International Journal of Solids and Structures, Vol. 25, pp. 803-833. Ju, J. W. (1989) Energy-Based Coupled Elastoplasic Damage Models at Finite Strains, Journal of Engineering Mechanics, Vol. 115, No. 11, pp. 2507-2525. Ju, J. W. (1990) Isotropic and Anisotropic Damage Variables in Continuum Damage Mechanics, Journal of Engineering Mechanics, Vol. 116, No. 12, pp. 2764-2770. Ju, J. W. and Lee, X. (1991) Micromechanical Damage Models for Brittle Solids, I: Tensile Loadings, Journal of Engineering Mechanics, Vol. 117, No. 7, pp. 1495-1514. Ju, J. W. and Chen, Tsung-Muh (1994) Effective Elastic Moduli of TwoDimensional Brittle Solids with Interacting Microcracks, Part I: Basic Formulations, Journal of Applied Mechanics, Vol. 61, pp. 349-357. Ju, J. W. and Chen, Tsung-Muh (1994) Effective Elastic Moduli of TwoDimensional Brittle Solids with Interacting Microcracks, Part I: Evolutionary Damage Models, Journal of Applied Mechanics, Vol. 61, pp. 358-366. Kachanov, L. M. (1958) On the Creep Fracture Time, Izv Akad, Nauk USSR Otd, Tekh., Vol. 8, pp. 26-31 (in Russian). Kachanov, L. M. (1986) Introduction to Continuum Damage Mechanics, Martinus Nijhoff Publishers, The Netherlands. Kattan, P. I. and Voyiadjis, G. Z. (1990) A Coupled Theory of Damage Mechanics and Finite Strain Elasto-Plasticity, Part I: Damage and Elastic


246

Damage Mechanics

Deformations, International Journal of Engineering Science, Vol. 28, No.5, pp. 421-435. Kattan, P. and Voyiadjis, G. (1993) A Plasticity-Damage Theory for Large Deformation of Solids - Part II: Applications to Finite Simple Shear, International Journal of Engineering Science, Vol. 31, No. 1, pp. 183-199. Kattan, P. and Voyiadjis, G. (2001a) Damage Mechanics with Finite Elements: Practical Applications with Computer Tools, Springer-Verlag, Germany. Kattan, P. and Voyiadjis, G. (2001b) Decomposition of Damage Tensor in Continuum Damage Mechanics, ASCE Journal of Engineering Mechanics, Vol. 127, No. 9, pp. 940-944. Kofler, M. (1997) Maple: An Introduction and Reference, Addison-Wesley, United Kingdom. Krajcinovic, D. (1983) Constitutive Equations for Damaging Materials, Journal of Applied Mechanics, ASME, Vol. 50, pp. 355-360. Krajcinovic, D. (1984) Continuum Damage Mechanics, Applied Mechanics, Reviews, Vol. 37, pp. 1-6. Krajcinovic, D. (1985) Continuous Damage Mechanics Revisited: Basic Concepts and Definitions, Journal of Applied Mechanics, Vol. 52, pp. 829834. Krajcinovic, D. and Foneska, G. U. (1981) The Continuum Damage Theory for Brittle Materials, Journal of Applied Mechanics, ASME, Vol. 48, pp. 809-824. Krajcinovic, D. and Mastilovic, S. (1995) Some Fundamental Issues of Damage Mechanics, Mechanics of Materials, Vol. 21, pp. 217-230. Kyoya, T., Ichikawa, Y, and Kawamoto, T. (1985) A Damage Mechanics Theory for Discontinuous Rock Mass, Numerial Methods in Geomechanics, Roterdam, pp. 469-480. Ladeveze, P. and Lemaitre, J. (1984) Damage Effective Stress in QuasiUnilateral Conditions, The 16th International Congress of Theoretical and Applied Mechanics, Lyngby, Denmark. Lai, W., Rubin, D., and Krempl, E. (1984) Introduction to Continuum Mechanics, Revised Edition, Pergamon Press, United Kingdom. Leckie, F. A. and Hayhurst, D. (1974) Creep Rupture of Stresses, Proceedings of the Royal Society, London, Vol. A340, pp. 323-347. Leckie, F. A. and Hayhurst, D. R. (1975) The Damage Concept in Creep Mechanics, Mechanics Research Communications, Vol. 2, pp. 23-26.


References

247

Leckie, F. and Onat, E. (1980) Tensorial Nature of Damage Measuring Internal Variables, in IUTAM Colloquim on Phyisical Nonlinearities in Structural Analysis, pp. 140-155, Springer-Verlag, Germany. Leckie, F. A. and Ponter, A. R. S. (1974) On the State Variable Description of Creeping Materials, Ingenieur Archiv, Vol. 43, pp. 158-167. Leckie, F. A. (1993) Tensorial Nature of Damage Measuring Internal Variables, International Journal of Solids and Structures, Vol. 30, No. 1, pp. 19-36. Lee, E. (1981) Some Comments on Elastic-Plastic Analysis, International Journal of Solids and Structures, Vol. 17, pp. 859-872. Lee, H., Li, G., and Lee, S. (1986) The Influence of Anisotropic Damage on the Elastic Behavior of Materials, International Seminar on Local Approach of Fracture, Moret-sur-Loing, France, pp. 79-90. Lee, E., Mallet, R., and Wertheimer, T. (1983) Stress Analysis for Anisotropic Hardening in Finite-Deformation Plasticity, Journal of Applied Mechanics, ASME, Vol. 50, pp. 554-560. Lee, H., Li, G. and Lee, S. (1986) The Influence of Anisotropic Damage on the Elastic Behavior of Materials, In International Seminar on Local Approach of Fracture, Moret-sur-Laing, France, pp. 79-90. Lee, H., Peng, K., and Wang, J. (1985) An Anisotropic Damage Criterion for Deformation Instability and its Application to Forming Limit Analysis of Metal Plates, Engineering Fracture Mechanics, Vol. 21, pp. 1031-1054. Lee, X. and Ju, J. W. (1991) Micromechanical Damage Models for Brittle Solids, II: Compressive Loadings, Journal of Engineering Mechanics, Vol. 117, No. 7, pp. 1515-1536. Lemaitre, J. (1971) Evaluation of Dissipation and Damage in Metals Subjected to Dynamic Loading, Proceedings of I.C.M., Kyoto, Japan. Lemaitre, J. (1984) How to Use Damage Mechanics, Nuclear Engineering and Design, Vol. 80, pp. 233-245. Lemaitre, J. (1985) A Continuous Damage Mechanics Model of Ductile Fracture, Journal of Engineering Materials and Technology, Vol. 107, No. 42, pp. 83-89. Lemaitre, J. (1986) Local Approach to Fracture, Engineering Fracture Mechanics, Vol. 25, Nos. 5/6, pp. 523-537. Lemaitre, J. (1996) A Course on Damage Mechanics, Second Edition, SpringerVerlag, Germany. Lemaitre, J. and Chaboche, J. L. (1974) A Nonlinear Model of Creep Fatigue Cumulation and Interaction, Proc. IUTAM, Symposium on Mechanics of Viscoelastic Media Bodies, Edited by Hult, pp. 291-301.


248

Damage Mechanics

Lemaitre, J. and Chaboche, J. L. (1975) A Nonlinear Model of Creep Fatigue Cumulation and Interaction, Proc. IUTAM, Symposium on Mechanics of Viscoelastic Media and Bodies (Edited by Hult), pp. 291-301. Lemaitre, J. and Chaboche, J. L. (1978) Aspect Phenomenologique de la Rupture par Endommagement, Journal de Mecanique Appiquee, Vol. 2, pp. 317-365. Lemaitre, J. and Chaboche, J. L. (1985) Mecanique de Materiaux Solides, Dunod, Paris. Lemaitre, J. and Chaboche, J. (1994) Mechanics of Solid Materials, Cambridge University Press, United Kingdom. Lemaitre, J. and Dufailly, J. (1987) Damage Measurements, Engineering Fracture Mechanics, Vol. 28, Nos. 5/6, pp. 643-661. Loret, B. (1983) On the Effects of Plastic Rotation in the Deformation of Anisotropic Elasto-Plastic Materials, Mechanics of Materials Journal, Vol. 2, pp. 287-304. Lu, T. J. and Chow, C. L. (1990) On Constitutive Equations of Inelastic Solids with Anisotropic Damage, Theoretical and Applied Fracture Mechanics, Vol. 14, pp. 187-218. Lubarda, V. and Krajcinovic, D. (1995) Some Fundamental Issues in Rate Theory of Damage Elasto-plasticity, International Journal of Plasticity, Vol. 11, No. 7, pp. 763-797. Lubarda, V. A., Krajcinovic, D. and Mastilovic, S. (1994) Damage Model for Brittle Elastic Solids with Unequal Tensile and Compressive Strengths, Engineering Fracture Mechanics, Vol. 49, No. 5, pp. 681-697. Lubliner, J. (1990) Plasticity Theory, Macmillan, New York, USA. Mandel, J. (1973) Relations de Comportment des Millieux E1astiques P1astiques et E1astiques - Viscop1astiques. Notion de Repere Directeur Foundations of Plasticity, A. Sawczu, (editor), Noordhoff, Leyden, pp. 387400. Marsden, J. and Hughes, T. (1983) Mathematical Foundations of Elasticity, Dover, New York, USA. Maugin, G. (1992) The Thermomechanics of Plasticity and Fracture, Cambridge University Press, United Kingdom. McDonald, P. (1996) Continuum Mechanics, PWS, ITP, Boston, USA. McDowell, D. L. (1987) An evaluation of recent developments in hardening and flow rules for rate independent cyclic plasticity, J. Appl. Mech Vol. 54, pp. 323-334.


References

249

Mroz, Z. (1967) On the description of anisotropic workhardening, Journal of Mechanical Physics and Solids Vol. 15, pp. 163. Mroz, Z. (1969) An attempt to describe the behavior of metals under cyclic loads using a more general workhardening model, Acta Mechanica Vol. 7, pp. 199-212. Mroz, Z. (1973) Mathematical Models of Inelastic Material Behavior, University of Waterloo, pp. 120-146. Murakami, S. (1983) Notion of Continuum Damage Mechanics and its Application to Anisotropic Creep Damage Theory, Journal of Engineering Materials and Technology, Vol. 105, pp. 99-105. Murakami, S. (1988) Mechanical Modeling of Material Damage, Journal of Applied Mechanics, ASME, Vol. 55, pp. 280-286. Murakami, S. and Imaizumi, T. (1982) Mechanical Description of Creep Damage State and its Experimental Verification, Journal de Mecanique Theorique et Appliquee, Vol. 1, pp. 743-761. Murakami, S. and Ohno, N. (1978) Creep Damage Analysis in Thin-Walled Tubes, in Inelastic Behavior of Pressure Vessel and Piping Components, edited by T. Y. Chang and E. Krempl, PVP-PB-028, ASME, New York, pp. 55-69. Murakami, S. and Ohno, N. (1980) A Continuum Theory of Creep and Creep Damage, In A. R. S. Ponter and D. R. Hayhurst, editors, Creep in Structures, IUTAM 8rd Symposium, Leicester, UK, September 8-12, pp. 422-443. Springer Verlag. Murkami, S. and Ohno, N. (1981) A Continuum Theory of Creep and Creep Damage, in Proceedings of the Third IUTAM Symposium on Creep in Structures, pp. 422-444, Springer-Verlag, Germany. Murakami, S., Sanomura, Y. and Saitoh, K. (1986) Formulation of CrossHardening in Creep and its Effect on the Creep Damage Process of Copper, ASME Journal of Engineering Materials and Technology, Vol. 108, pp. 167-173. Nermat-Nasser, S. (1979) Decomposition of Strain Measures and Their Rates in Finite Deformation Elastopasticity, International Journal of Solids and Structures, Vol. 15, pp. 155-166. Nermat-Nasser, S. (1983) On Finite Plastic Flow of Crystalline Solids and Geomaterials, Journal of Applied Mechanics, ASME, Vol. 50, pp. 11141126. Nicolaides, R. and Walkington, N. (1996) Maple: A Comprehensive Introduction, Cambridge University Press, United Kingdom.


250

Damage Mechanics

Ohno, N. (1982) A constitutive model of cyclic plasticity with a nonhardening strain region, ASME Journal of Applied Mechanics Vol. 49, pp. 721-727. Ohno, N. and Wang, J. D. (1991) Two equivalent forms of nonlinear kinematic hardening: application to nonisothermal plasticity, International Journal of Plasticity Vol. 7, pp. 637-650. Ohno, N. and Wang, J. D. (1993) Kinematic hardening rules with critical state of dynamic recovery, Part I: Formulation and basic features for ratchetting behavior, International Journal of Plasticity Vol. 9, No. 375-390. Oldroyd, J. (1950) On the Foundation of Rheological Equations of State, Proceedings of the Royal Society, London, Vol. A200, pp. 523-541. Onat, E. T. (1986) Representation of Mechanical Behavior in the Presence of Internal Damage, Engineering fracture Mechanics, Vol. 25, No. 5/6, pp. 605-614. Onat, E. and Leckie, F. (1988) Representation of Mechanical Behavior in the Presence of Changing Internal Structure, Journal of Applied Mechanics, ASME, Vol. 55, pp. 1-10. Ortiz, M. and Simo, C. (1986) An Analysis of a New Class of Integration Algorithms for Elasto-plastic Constitutive Relations, International Journal for Numerical Methods in Engineering, Vol. 23, pp. 353-366. Park, T. and Voyiadjis, G. Z., (1998) ”Kinematic Description of Damage”, Journal of Applied Mechanics, ASME, Vol. 65, pp. 93-98. Paulun, J. and Pecherski, R. (1985) Study of Corotational Rates for Kinematic Hardening of in Finite-Deformation Plasticity, Archives of Mechanics, Vol. 37, No. 6, pp. 661-677. Perzyna, P. (1963) The Constitutive Equations for Rate Sensitive Plastic Material, Applied Mathematics, Vol. 20, pp. 321-332. Perzyna, P. (1971) Thermodynamic Theory of Viscoplasticity, Advances in the Applied Mathematics, Vol. 11, pp. 313-345. Phillips, A., Tang, J. L. and Ricciuti, M. (1974) Some new observations on yield surfaces, Acta Mechanica Vol. 20, pp. 23-39. Rabotnov, Y. N. (1968) Creep Rupture, in Proceedings, Applied Mechanics Conference, Stanford University, edited by M. Hetenyi and H. Vincenti, pp. 342-349. Rabotnov, Y. N. (1969) Creep Problems of Structural Mechanics, North Holland, Amsterdam. Rivlin, R. S. and Smith, G. F. (1969) Orthogonal Integrity Basis for N Symmetric Matrices, in Contributions to Mechanics, edited by D. Abir, Pergamon Press, Oxford, pp. 121-141.


References

251

Rubin, M. (1982) A Thermoelastic Viscoplastic Model with a Rate Dependent Yield Strength, ASME Journal of Applied Mechanics, Vol. 49, pp. 305-311. Schwartz, D. (1999) An Introduction to Maple, Prentice Hall, New Jersey, USA. Segel, L. (1987) Mathematics Applied to Continuum Mechanics, Dover, New York, USA. Shiratori, E., Ikegami, K. and Yoshida, F. (1979) Analysis of stress-strain relations of use of an anisotropic hardening potential, J. Mech. Physics Solids Vol. 27, pp. 213-229. Sidoroff, F. (1979) Description of Anisotropic Damage Application to Elasticity, In JeanPaul Boehler, editor, Mechanical Behavior of Anisotropic Solids / N295 Comportement Mecanique Des Solides Anisotropes. Martinus Nijhoff Publishers, 1979. Proceedings of the Euromech Colloquim 115, N295 Villard-de-Lans, June 19-22, France. Sidoroff, F. (1980) Description of Anisotropic Damage Application to Elasticity, In J. Hult and J. Lemaitre, editors, Physical Non-Linearities in Structural Analysis, IUTAM Series, pp. 237-244, Springer-Verlag. Sidoroff, F. (1981) Description of Anisotropic Damage Application to Elasticity, in IUTAM Colloqium on Physical Nonlinearities in Structural Analysis, pp. 237-244, Springer-Verlag, Germany. Simo, J. and Ju, J. (1987) Strain and Stress-Based Continuum Damage Models - Part I: Formulation, International Journal of Solids and Structures, Vol. 23, No. 7, pp. 821-840. Simo, J. and Pister, K. (1984) Remarks on Rate Constitutive Equations for Finite Deformation Problems: Computational Implications, Computer Methods in Applied Mechanics and Engineering, Vol. 46, pp. 201-215. Smith, G. F. (1971) On Isotropic Functions of Symmetric Tensors, SkewSymmetric Tensors, and Vectors, International Journal of Engineering Science, Vol. 9, pp. 899-916. Spencer, A. J. M. (1971) Theory of Invariants, in Continuum Physics, edited by A. C. Eringen, Vol. 1, Mathematics, Academic Press, New York and London. Spencer, A. J. M. and Rivlin, R. S. (1958/1959a) The Theory of Matrix Polynomials and its Application to the Mechanics of Isotropic Continua, Arch. Rational Mech. Anal., Vol. 2, pp. 309-336. Spencer, A. J. M. and Rivlin, R. S. (1958/1959b) Finite Integrity Bases for Five or Fewer Symmetric 3 x 3 Matrices, Arch. Rational Mech. Anal., Vol. 2, pp. 435-446.


252

Damage Mechanics

Srivatsavan, P. and Subramanyan, S. (1978) A Cumulative Damage Rule Based on Successive Reduction in Fatigue Limit, Journal of Engineering Mechanics and Technology, Vol. 100, pp. 212-214. Stolz, C. (1986) General Relationships between Micro and Macro Scales for the Nonlinear Behavior of Heterogeneous Media, in Modeling Small Deformations of Polycrystals, Edited by J. Gittus and J. Zarka, pp. 89115, Elsevier, The Netherlands. Stumvoll and Swoboda (1993) Deformation Behavior of Ductile Solids Containing Anisotropic Damage, ASCE Journal of Engineering Mechanics, Vol. 119, No. 7, pp. 169-192. Subramanyan, S. (1976) A Cumulative Damage Rule Based on the Knee Point of the S-N Curve, Journal of Engineering Mechanics and Technology, Vol. 98, pp. 316-321. Tsamasphyras, G. and Giannakopoulos, A. E. (1989) The Optimum Finite Element Grids Around Crack Singularities in Bilinear Elasto-plastic Materials, Engineering Fracture Mechanics, Vol. 32, No.4, pp. 515-522. Tseng, N. T. and Lee, G. C. (1983) Simple plasticity model of the twosurface type, ASCE J. Engineering Mechanics Vol. 109, No. 3, pp. 795810. Tvergaard, V. (1982) Material Failure by Void Coalescence in Localized Shear Bands, International Journal of Solids and Structures, Vol. 18, pp. 659-672. Tvergaard, V. and Needleman, A. (1984) Analysis of Cup-Cone Fracture in a Round Tensile Bar, Acta Metallurgica, Vol. 32, p. 157. Voyiadjis, G. Z. (1984) Experimental Determination of the Material Parameters of the Elasto-Plastic Work Hardening of Metal Alloys, Material Science and Engineering Journal, Vol. 62, No. 1, pp. 99-107. Voyiadjis, G. Z. (1988) Degradation of Elastic Modulus in Elasto-Plastic Coupling with Finite Strains, International Journal of Plasticity, Vol. 4, pp. 335-353. Voyiadjis, G. Z. and Basuroychowdury, I. N. (1998) A Plasticity Model for Multiaxial Cyclic Loading and Ratcheting, Acta Mechanica, Vol. 126, pp. 19-35. Voyiadjis, G. Z. and Foroozesh, M. (1990) An Anisotropic Distortional Yield Model, ASME Journal of Applied Mechanics, Vol. 57, pp. 537-547. Voyiadjis, G. Z. and Guelzim, Z. (1996) A Coupled Incremental Damage and Plasticity Theory for Metal Matrix Composites, Journal of the Mechanical Behavior of Materials, Vol. 6, No. 3, pp. 193-219.


References

253

Voyiadjis, G. Z. and Kattan, P. I. (1989) Eulerian Constitutive Model for Finite-Strain Plasticity with Anisotropic Hardening, Mechanics of Material Journal, Vol. 7, No. 4, pp. 279-293. Voyiadjis, G. Z. and Kattan, P. I.(1990) A Coupled Theory of Damage Mechanics and Finite-Strain Elasto-Plasticity - Part II: Damage and FiniteStrain Plasticity, International Journal of Engineering Science, Vol. 28, No. 6, pp. 505-524. Voyiadjis, G. Z. and Kattan, P. I. (1992) A Plasticity-Damage Theory for Large Deformation of Solids - Part I: Theoretical Formulation, International Journal of Engineering Science, Vol. 30, No. 9, pp. 1089-1108. Voyiadjis, G. Z. and Kattan, P. I. (1993) Anisotropic Damage Mechanics Modeling in Metal Matrix Composites, Technical Report, Final Report Submitted to the Air Force Office of Scientific Research. Voyiadjis, G. Z. and Kattan, P. I. (1993) Damage of Fiber-Reinforced Composite Materials with Micromechanical Characterization, International Journal of Solids and Structures, Vol. 30, No. 20, pp. 2757-2778. Voyiadjis, G. Z. and Kattan, P. I. (1996) On the Symmetrization of the Effective Stress Tensor in Continuum Damage Mechanics, Journal of the Mechanical Behavior of Materials, Vol. 7, No. 2, pp. 139-165. Voyiadjis, G. Z. and Kattan, P. I. (1999) Advances in Damage Mechanics: Metals and Metal Matrix Composites, Elsevier, The Netherlands. Voyiadjis, G. Z. and Kiousis, P. (1987) Stress Rate and the Langrangian Formulation of the Finite-Strain Plasticity for a von Mises Kinematic Hardening Model, International Journal of Solids and Structures, Vol. 23, No. 1, pp. 95-109. Voyiadjis, G. Z. and Mohammad, L. (1976) Rate Equations for Viscoplastic Materials Subjected to Finite Strain, International Journal of Solids and Structures, Vol. 12, pp. 81-97. Voyiadjis, G. Z. and Park, T. (1995a) Anisotropic Damage of Fiber Reinforced MMC Using An Overall Damage Analysis, Journal of Engineering Mechanics, Vol. 121, No. 11, pp. 1209-1217. Voyiadjis, G. Z. and Park, T. (1995b) Local and Interfacial Damage Analysis of Metal Matrix Composites, International Journal of Engineering Science, Vol. 33, No. 11, pp. 1595-1621. Voyiadjis, G. Z. and Park, T. (1996a) Anisotropic Damage Effect Tensors for the Symmetrization of the Effective Stress Tensor, Journal of Applied Mechanics, Vol. 64, No. 1, pp. 107-110. Voyiadjis, G. Z. and Park, T. (1996b) Anisotropic Damage for the Characterization of the Onset of Macro-Crack Initiation in Metals, International Journal of Damage Mechanics, Vol. 5, pp. 68-92.


254

Damage Mechanics

Voyiadjis, G. Z. and Park, T. (1997) Anisotropic Damage Effect Tensors for the Symmetrization of the Effective Stress Tensor, Journal of Applied Mechanics, Vol. 5, pp. 106-110. Voyiadjis, G. and Park, T. (1999) Kinematics of Damage for Finite-Strain Plasticity, International Journal of Engineering Science, Vol?, pp. 1-28. Voyiadjis, G. Z. and Sivakumar, S. M. (1991) A robust kinematic hardening rule with ratchetting effects: Part I. Theoretical formulation, Acta Mechanica Vol. 90, pp. 105-123. Voyiadjis, G. Z. and Sivakumar, S. M. (1992) A Finite Strain and Rate Dependent Cyclic Plasticity Model for Metallics, In C. Tenddosiu, J. L. Raphanel, and F. Sidoroff editors, Proceedings of the International Seminar MECAMAT91, Fountainbleau, France, on Large Plastic Deformation: Fundamental Aspects and Applications to Metal Forming, pp. 353-360. Voyiadjis, G. Z. and Sivakumar, S. M. (1994) A robust kinematic hardening rule with ratchetting effects: Part n. Application to nonproportionalloading cases, Acta Mechanica Vol. 107, pp. 117-136. Voyiadjis, G. Z., Thiagarajan, G. and Petarkis, E. (1995) Constitutive modelling for granular media using an anisotropic distortional model. Acta Mechanica Vol. 110, pp. 151-171. Voyiadjis, G. Z. and Venson, A. R. (1995) Experimental Damage Investigation of a SiC- Ti Alumini de Metal Matrix Composite, International Journal of Damage Mechanics, Vol. 4, No. 4, pp. 338361. Wang, C. C. (1970) A New Representation Theorem for Isotropic Functions: An Answer to Professor G. F. Smith’s Criticism of my Papers on Representations of Isotropic Functions, Part 2, Arch. Rational Mech. Anal., Vol. 36, pp. 198-223. Werde, R. (1972) Introduction to Vector and Tensor Analysis, Dover, New York, USA. Wilt, T. and Arnold, S. (1994) A Coupled/Uncoupled Deformation and Fatigue Damage Algorithm Utilizing the Finite Element Method, NASA TM 106526, NASA, Lewis Research Center, Cleveland, OH. Zbib, H. M. (1993) On the Mechanics of Large Inelastic Deformations: Kinematics and Constitutive Modeling, Acta Mechania, Vol. 96, pp. 119138. Ziegler, H. (1959) A Modification of Prager’s Hardening Rule, Quarterly of Applied Mathematics, Vol. 17, pp. 55-65.


Damage Mechanics (Dekker Mechanical Engineering)

Damage Mechanics (Dekker Mechanical Engineering)

Target Costing (Dekker Mechanical Engineering)

Engineering Damage Mechanics

Applied Computational Fluid Dynamics (Mechanical Engineering Series) (Dekker Mechanical Engineering)

Damage Mechanics in Engineering Materials

Turbomachinery: Design and Theory (Dekker Mechanical Engineering)

Intermediate Heat Transfer (Mechanical Engineering (Marcell Dekker))

Principles of Biomechanics (Dekker Mechanical Engineering)

Pressure Sensors (Mechanical Engineering (Marcell Dekker))

Theory of Dimensioning (Dekker Mechanical Engineering)

Liquid Pipeline Hydraulics (Dekker Mechanical Engineering)

Lubrication Fundamentals, Second Edition (Dekker Mechanical Engineering)

Mechanical Life Cycle Handbook (Mechanical Engineering (Marcell Dekker))

Mechanical Properties of Engineered Materials (Mechanical Engineering (Marcell Dekker))

Fluidized Bed Combustion (Dekker Mechanical Engineering)

Probability Applications in Mechanical Design (Dekker Mechanical Engineering)

Mechanical Life Cycle Handbook (Mechanical Engineering (Marcell Dekker))

Engineering Documentation Control Practices & Procedures (Mechanical Engineering (Marcell Dekker))

Standards for Engineering Design and Manufacturing (Dekker Mechanical Engineering)

Implementing Concurrent Engineering in Small Companies (Dekker Mechanical Engineering)

Structural Analysis of Polymeric Composite Materials (Mechanical Engineering, 165) (Mechanical Engineering (Marcell Dekker))

Introduction to Contact Mechanics (Mechanical Engineering Series)

Boundary Methods: Elements, Contours, and Nodes (Dekker Mechanical Engineering)

Heat Exchanger Design Handbook (Mechanical Engineering (Marcell Dekker))

Applied Finite Element Modeling (Mechanical Engineering (Marcell Dekker))

Designing for Product Sound Quality (Mechanical Engineering (Marcell Dekker))

Introduction to Contact Mechanics (Mechanical Engineering Series)

Ultrasonics: Fundamentals, Technologies, and Applications, Third Edition (Dekker Mechanical Engineering)

Clutches and Brakes: Design and Selection (Dekker Mechanical Engineering)

Industrial Noise Control and Acoustics (Dekker Mechanical Engineering)

Damage Mechanics (Dekker Mechanical Engineering)