Advances in Applied Mechanics, Volume 42

ADVANCES IN APPLIED MECHANICS Edited by Hassan Aref VIRGINIA TECH COLLEGE OF ENGINEERING BLACKSBURG, VA, USA Erik va...

Author: Erik van der Giessen | Hassan Aref

26 downloads 759 Views 5MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form

DOWNLOAD PDF

ADVANCES IN

APPLIED MECHANICS Edited by

Hassan Aref VIRGINIA TECH COLLEGE OF ENGINEERING BLACKSBURG, VA, USA

Erik van der Giessen UNIVERSITY OF GRONINGEN GRONINGEN, THE NETHERLANDS

VOLUME 42

Amsterdam • Boston • Heidelberg • London • New York • Oxford Paris • San Diego • San Francisco • Singapore • Sydney • Tokyo Academic Press is an imprint of Elsevier

ACADEMIC PRESS

Academic Press is an imprint of Elsevier 32 Jamestown Road, London NW1 7BY, UK Radarweg 29, PO Box 211, 1000 AE Amsterdam, The Netherlands The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK 30 Corporate Drive, Suite 400, Burlington, MA 01803, USA 525 B Street, Suite 1900, San Diego, CA 92101-4495, USA Copyright © 2009 by Elsevier Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher. Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (+44) (0) 1865 843830; fax (+44) (0) 1865 853333; email: [email protected]. Alternatively you can submit your request online by visiting the Elsevier web site at http://elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material. Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. ISBN: 978-0-12-374291-9 ISSN: 0065-2156

For information on all Academic Press publications visit our website at www.elsevierdirect.com

Printed and bound in USA 09 10 11 12 10 9 8 7 6 5 4 3 2 1

Preface

Applied mechanics is a classical subject by any standard but is nevertheless vibrant in new areas of science and technology. These days, nanotechnology is one of the emerging fields where mechanics is proving to be a powerful tool. In this and in many other subjects, multiscale modelling is a maturing paradigm, involving solid and fluid mechanics alike. This volume of the series Advances in Applied Mechanics contains three examples of modern directions in mechanics, where homogenization (or coarse graining) is a common notion. The first chapter, co-authored by Duan and Karihaloo from Cardiff University together with Wang from Peking University, deals with a careful consideration of continuum mechanics at very small-length scales. One of the nanoscale properties absent in classical continuum theories is surface stress, an effect becoming more and more important at smaller scales as the surface area increases compared to the volume. While surface stress is an atomistic phenomenon, the authors show that it is possible to extend continuum elasticity with surface elasticity. Subsequently, they demonstrate that these surface effects can have a beneficial influence on the overall stiffness of nano porous materials. The theme is continued in the second chapter where Sevostianov and Kachanov marry the homogenization of elasticity and that of thermal conductivity. While homogenization for each of them is a well established, this chapter details the connection between them, something that is far from trivial since the phenomena are governed by partial differential equations of different order. In particular, the authors derive explicit closed-form relations between effective elastic properties and effective conductive properties for anisotropic materials. The results are applied to various problems involving porous, cracked and/or fiber-reinforced materials. The final chapter, Coarse Graining in Elastoviscoplasticity, is a unique example of how solid and fluid mechanics can cross-fertilize. Here, Hütter and Tervoort from ETH-Zürich review the coarse-graining scheme GENERIC originally developed for fluids and apply it to elastic and viscoelastic deformations of solids. In particular, they show how continuum viscoplasticity can be derived from the motion of the underlying microscopic particles. The theory constitutes a systematic approach, based on techniques from statistical physics, to the averaging over intermediate-length scales as well as time scales. We hope that this volume of Advances in Applied Mechanics not only gives an account of some of the exciting new developments in mechanics but also demonstrates how these tools are applied and needed in modern science and technology. Hassan Aref Erik van der Giessen vii

Theory of Elasticity at the Nanoscale H. L. DUANa,b , J. WANGb and B. L. KARIHALOOa∗ a School of Engineering, Cardiff University, Queen’s Buildings, The Parade, Cardiff CF24 3AA, UK ∗ [email protected] b State Key Laboratory for Turbulence and Complex System and Department of Mechanics and Aerospace Engineering, College of Engineering, Peking University, Beijing, 100871, P. R. China

Abstract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2

2. Eshelby Formalism for Nano-inhomogeneities . . . . . . . . . . . . . . . . . . . . . 2.1. Basic Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2. Eshelby Formalism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 6 9

3. Application of Eshelby Formalism for Nano-inhomogeneities . . . . . . . . 3.1. Stress Concentration Factor of a Spherical or Circular Nanovoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2. Strain Fields in QDs With Multi-shell Structures and in Alloyed QDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3. Compatible Composition Profiles and Critical Sizes of Alloyed QDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

4. Micromechanical Framework for Nano-inhomogeneities with Interface Stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Application of Micromechanical Framework for Nano-inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1. Elastic Moduli of Solids with Spherical Nano-inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2. Generalized Levin’s Formula and Hill’s Connections . . . . . . . . . . . 5.3. Prediction and Tailoring of Elastic Moduli of Nanochannel-array Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19 21 27 30 34 34 40 47

6. Scaling Laws for Properties of Nanostructured Materials . . . . . . . . . . . . 6.1. Elastic Properties with Surface Stress Effect . . . . . . . . . . . . . . . . . . 6.2. Melting Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

57 58 62

7. Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

62

Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

ADVANCES IN APPLIED MECHANICS, VOL. 42 ISSN: 0065-2156 DOI: 10.1016/S0065-2156(08)00001-X

1

Copyright © 2008 by Elsevier Inc. All rights reserved.

2

H. L. Duan et al.

Abstract We have shown in a series of recent papers that the classical theory of elasticity can be extended to the nanoscale by supplementing the equations of elasticity for the bulk material with the generalized Young–Laplace equations of surface elasticity. This review article shows how this has been done in order to capture the often unusual mechanical and physical properties of nanostructured particulate and porous materials. It begins with a description of the generalized Young–Laplace equations. It then generalizes the classical Eshelby formalism for nano-inhomogeneities; the Eshelby tensor now depends on the size of the inhomogeneity and the location of the material point in it. Then the stress concentration factor of a spherical nanovoid is calculated, as well as the strain fields in quantum dots (QDs) with multi-shell structures and in alloyed QDs induced by the mismatch in the lattice constants of the atomic species. This is followed by a generalization of the micromechanical framework for determining the effective elastic properties and effective coefficients of thermal expansion of heterogeneous solids containing nano-inhomogeneities. It is shown, for example, that the elastic constants of nanochannel-array materials with a large surface area can be made to exceed those of the nonporous matrices through pore surface modification or coating. Finally, the scaling laws governing the properties of nanostructured materials are derived. The underlying cause of the size dependence of these properties at the nanoscale is the competition between surface and bulk energies. These laws provide a yardstick for checking the accuracy of experimentally measured or numerically computed properties of nanostructured materials over a broad size range and can thus help replace repeated and exhaustive testing by one or a few tests.

1. Introduction In any material system, the atoms at a free surface experience a different local environment than the atoms away from the surface because of reduced coordination. As a result, the energy associated with these atoms is generally different from that of the atoms in the bulk. Surface stress relates the variation of the excess free energy to the strain of the surface (e.g., Cammarata, 1997). The same situation arises at the interface between two dissimilar materials; the atoms near the interface experience a different local environment than the atoms farther away from the interface in either of the abutting materials. As these surface/interface stresses act on only a few layers of atoms near the surface/interface, their effect is not felt in the bulk of the material, and it is therefore neglected in the classical theory of elasticity. However, it can no longer be neglected in a nanostructured material whose characteristic length is in the nanometer range because the surface stresses displace atoms from the equilibrium positions which they normally occupy in bulk macroscopic assemblies (Streitz et al., 1994). This change in interatomic distance affects the elastic properties of nanoscale structures. For nanostructured (Gleiter, 2000) and nanochannel-array materials (Masuda and Fukuda, 1995; Martin and Siwy, 2004) with a large surface to the bulk ratio, the surface stress effect can

Theory of Elasticity at the Nanoscale

3

be substantial. Thus, materials such as thin films, nanowires, and nanotubes may exhibit unusual properties not noticed at the macroscale. As small devices and nanostructures are all pervasive, and the elastic constants of materials are a fundamental physical property, it is important to understand and predict the size effect in elastic properties of materials at the nanoscale. The concept of surface/interface stress in solids was first introduced by Gibbs (1906) and has been steadily developed since (e.g., Shuttleworth, 1950; Herring, 1953; Orowan, 1970; Murr, 1975; Cahn, 1978; Cammarata, 1994). The surface/ interface stress can be defined in various ways. One definition is the surface excess of bulk stress (Ibach, 1997; Müller and Saúl, 2004). Another definition is given through the Shuttleworth equation (Shuttleworth, 1950). Moreover, Nix and Gao (1998) presented an atomistic interpretation of interface stress. Generally, two types of interface stress in solids have been discussed in the literature. One type is related to a deformation that maintains the interface coherency between the abutting solids (with equal tangential strain). In this kind of deformation, no atomic bonds break in the interface plane. Another type of interface stress is related to the deformation with different tangential strains in the two solids (Weissmüller and Cahn, 1997; Gurtin et al., 1998). In this case, atomic bonds may break in the interface plane, as slipping occurs across the interface. Generally, coherent interfaces are commonly present within materials, and interfaces often remain coherent under a wide range of conditions (Rottman, 1988). Many attempts have been made recently to investigate the elastic properties of nanostructured materials by atomistic simulations. For example, Zhou and Huang (2004) and Villain et al. (2004) have obtained the elastic constants of nanoplates of copper and tungsten; they did not explicitly use the concept of surface stress to explain the variation of the elastic constants with the thickness of the nanoplates, but, obviously, the surface stress effect is implicitly taken into account in some atomistic calculations, for example, ab initio models. Diao et al. (2004) studied the effect of free surfaces on the structure and elastic properties of gold nanowires by atomistic simulations. Although the atomistic simulation is a good way to calculate the elastic constants of nanostructured materials, it is only applicable to homogeneous nanostructured materials (e.g., nanoplates, nanobeams, nanowires, etc.) with limited number of atoms. Moreover, it is difficult to obtain the elastic properties of the heterogeneous nanostructured materials using atomistic simulations. For these and other reasons, it is prudent to seek a more practical approach. One such approach would be to extend the classical theory of elasticity down to the nanoscale by including in it the hitherto neglected surface/interface effect. For this it is necessary first to cast the latter within the framework of continuum elasticity. The mathematical framework incorporating surface stress into continuum mechanics was established by Gurtin and Murdoch (1975, 1978), Murdoch (1976),

4

H. L. Duan et al.

and Gurtin et al. (1998). Miller and Shenoy (2000) compared the results obtained by the continuum model, which explicitly uses surface stress and surface elastic constants, with those obtained by the atomistic simulations for nanobeams and nanowires and found that the results were almost indistinguishable. In essence, the continuum surface stress model assumes that a nanostructure is made of the bulk and surfaces (Shenoy, 2005) with the surface moduli of the nanostructure being different from those of the bulk. Steigmann and Ogden (1999) have generalized the Gurtin–Murdoch theory (Gurtin and Murdoch, 1975) to account for the effect of flexural resistance of elastic films attached to the bounding surfaces of solids. The continuum theory of Gurtin and Murdoch (1975) was further developed by many researchers (Bottomley and Ogino, 2001; Cuenot et al., 2004; Ren and Zhao, 2004; Shenoy, 2005; Duan et al., 2005a,b; Dingreville et al., 2005; Jing et al., 2006) to analyze the elastic properties of homogeneous and heterogeneous nanostructured materials. For example, Cuenot et al. (2004) and Jing et al. (2006) analyzed the elastic properties of silver nanowires with outer diameters ranging from 20 to 140 nm using this theory and compared them with contact atomic force microscopy measurements. They found that the apparent Young modulus of the nanowires decreased with an increase in the diameter. This size dependence of the apparent Young modulus was attributed to the surface stress effect, which includes the effects of the surface stress, the oxidation layer, and the surface roughness. Gao et al. (2006) developed a finite element method taking into account the surface stress effect. The finite element method with surface stress effect can be used to analyze the elastic properties of nanostructured materials with complicated structures. Fang and Liu (2006) studied the size-dependent interaction between an edge dislocation and a circular nano-inhomogeneity. He and Lim (2006) derived the surface Green function for incompressible, elastically isotropic half-space coupled with surface stress by using the double Fourier transform technique. Mi and Kouris (2006) investigated the effect of surface/interface elasticity on the response of nanoparticles embedded in a semi-infinite elastic medium. Huang and Yu (2006) presented a relation between the surface stress and the electric field, that is, surface piezoelectricity, and showed that surface piezoelectricity plays an important role in the electromechanical behavior of piezoelectric nanostructures. Wang and Wang (2006) analyzed the deformation around a nanosized elliptical hole with surface stress effect. Wang et al. (2006) studied the effect of the surface stress on the diffraction of plane waves and the dynamic stress concentration around a nanosized hole. The elegant Eshelby formalism (Eshelby, 1957, 1959) for inclusions/ inhomogeneities is fundamental to the solution of many problems in materials science, solid state physics, and mechanics of heterogeneous materials. Not surprisingly, attempts have been made to extend the Eshelby formalism for


5

nano-inclusions/inhomogeneities. For example, Sharma et al. (2003) and Sharma and Ganti (2004) analyzed the elastic field of a spherical nano-inhomogeneity with the interface stress effect subjected to a combination of a uniform dilatational eigenstrain and a hydrostatic remote loading in an infinite medium. Duan et al. (2005a) extended the Eshelby formalism to nano-inhomogeneities. They gave the strain field in a nano-inhomogeneity subjected to an arbitrary uniform eigenstrain in an infinite elastic medium, the elastic field in a nano-inhomogeneity in an infinite medium subjected to an arbitrary uniform remote stress, and the strain energy in solids containing nano-inhomogeneities. Based on the generalized Eshelby formalism, attempts have been made to generalize the micromechanical framework for the prediction of the effective properties (e.g., effective elastic moduli and effective coefficients of thermal expansion (CTE)) of heterogeneous materials containing nano-inhomogeneities. For example, Duan et al. (2005b) gave the general micromechanical framework for the prediction of the effective elastic moduli of the heterogeneous materials containing spherical nano-inhomogeneities. Duan et al. (2006c) predicted the effective elastic moduli of nanochannel-array materials and showed that such materials can be made stiffer than the nonporous parent materials by judicious manipulation of the pore surface elasticity or by coating the pore surface with a nanolayer of a stiffer material. Subsequently, Chen et al. (2007a,b), Chen and Dvorak (2006), He (2006), and Duan and Karihaloo (2007) predicted the effective elastic moduli and effective CTE of the heterogeneous materials containing nano-inhomogeneities and gave some intrinsic relations governing these effective properties, for example, the generalized Levin’s formula and generalized Hill’s connections. Recently, Zhang and Wang (2007) extended a conventional micromechanical method for nonlinear composites (Qiu and Weng, 1992; Hu, 1996) to study the effect of the surface stress on the yield strength of nanoporous materials. As mentioned above, the continuum mechanics framework with surface stress effect has been used extensively to characterize the elastic properties of nanostructured materials. It has been shown that the theoretical predictions are in very good agreement with experiment. The continuum mechanics framework with surface stress effect is thus a very practical approach to characterize the nanostructured materials, as the molecular dynamic and ab initio approaches are limited to very small material samples. Therefore, it seems timely to review the advances made possible by the continuum mechanics framework that takes into account the surface stress effect. This review paper presents a unified framework for several topics at the interface of continuum mechanics and materials science. It provides the methods and fundamental solutions necessary to analyze the elastic and mechanical properties of nanostructured materials in which the surface/interface stress plays an important role. We note in passing that Fried and Gurtin (2004) also

6

H. L. Duan et al.

published a review paper on the interaction of continuum mechanics and materials science. However, they concentrated primarily on the dynamic processes of interface evolution due to the atomic transport at the grain boundaries. This review article is organized as follows. In Section 2, it begins with the description of the generalized Young–Laplace equations for surface elasticity. Then the Eshelby formalism for nano-inhomogeneities is given, which includes the Eshelby tensor the stress concentration tensor, and the Eshelby formula for strain energy. Next, the applications of Eshelby formalism for nano-inhomogeneity, that is, the stress concentration factor of a spherical nanovoid, and the strain fields in quantum dots (QDs) with multi-shell structures and in alloyed QDs induced by the mismatch in the lattice constants of the atomic species, are given in Section 3. This is followed in Section 4 by a generalization of the micromechanical framework for determining the effective elastic properties of heterogeneous solids containing nano-inhomogeneities. In Section 5, applications of micromechanical framework for nano-inhomogeneities are given. It is shown, for example, that the elastic constants of nanochannel-array materials with a large surface area can be made to exceed those of the nonporous matrices through pore surface modification or coating. Finally, the scaling laws governing the properties of nanostructured materials are derived in Section 6. These laws provide a yardstick for checking the accuracy of experimentally measured or numerically computed properties of nanostructured materials over a broad size range and can thus help replace repeated and exhaustive testing by one or a few tests. 2. Eshelby Formalism for Nano-inhomogeneities

2.1. Basic Equations The basic equations for solving boundary value problems of thermoelasticity consist of the following conventional equilibrium equations, constitutive equations, and strain-displacement relations for the constituent materials, that is, the matrix and the inhomogeneity embedded in it: 1 (2.1) ∇ · σ k = 0 , σ k = Ck : εk − T Dk , εk = ∇ ⊗ uk + uk ⊗ ∇ 2 where σ k , uk , and εk denote the stresses, displacements, and strains in k (k = I, m). In subsequent sections, I and m will denote an inhomogeneity and matrix, respectively. Ck are the elastic moduli of I and m . T is the temperature difference, Dk is the stress-temperature tensor in I and m . For the isotropic case, Dk = d k I(2) , where I(2) is the second-order identity tensor in threedimensional space. d k = αk (3λk + 2μk ), αk , λk , and μk are the CTE and elastic


7

Lamé moduli of I and m , respectively. In what follows, as we will study both spherical inhomogeneities and cylindrical fibers, we will use the super- and subscript k = p for the former, k = f for the latter, with k = m denoting the matrix. At the nanoscale, Eq. (2.1) have to be supplemented by the surface/interface elasticity equations to complete the mathematical description of the problem. As mentioned in the Section 1, a surface/interface stress can be defined in various ways, for example, the surface/interface excess of bulk stress (Müller and Saúl, 2004). To derive the surface/interface equations of elasticity, we consider a system of two abutting solids I and m with different elastic properties. The equilibrium of a general curved interface with the unit normal vector n between the two solids I and m requires that (Gurtin and Murdoch, 1975; Povstenko, 1993) [σ] · n = −∇S · τ,

(2.2)

where [σ] = σ I − σ m , σ I , and σ m are the volume stress tensors in I and m , respectively, ∇S · τ denotes the interface divergence of τ at (Gurtin and Murdoch, 1975). Eq. (2.2) is the generalized Young–Laplace equation for solids. It can be derived in various ways, for example, by the principle of virtual work (cf., the second Chapter of Duan (2005)). Huang and Wang (2006) derived the generalized Young–Laplace equation from the stationary condition of an energy functional for hyperelastic media. For a curved interface with two orthogonal unit base vectors e1 and e2 in the tangent plane and a unit vector n perpendicular to the interface, ∇S · τ can be expressed as follows (Duan et al., 2005a): e1 ∂(h2 τ11 ) ∂(h1 τ21 ) ∂h1 τ11 τ22 ∂h2 ∇S · τ = − n+ − + + τ12 − τ22 R1 R2 h1 h2 ∂α1 ∂α2 ∂α2 ∂α1 e2 ∂h1 ∂(h2 τ12 ) ∂h2 ∂(h1 τ22 ) + − . (2.3) τ11 + + τ21 + h1 h2 ∂α2 ∂α1 ∂α1 ∂α2 Here, α1 and α2 are two parameters defining the interface such that α1 = constant and α2 = constant give two sets of mutually orthogonal curves on , and h1 and h2 are the corresponding metric coefficients, R1 and R2 are the radii of the principal curvatures (see, e.g., Appendix A of Benveniste (2006) or the second Chapter of Duan (2005)). τ11 , τ22 , and τ12 are the components of the interface stress tensor τ. As can be seen from Eq. (2.3), the first term on the right-hand side is the classical Young–Laplace equation; the remaining terms signify that a nonuniform distribution of the interface stress or a uniform interface stress on a surface with varying curvature needs to be balanced by bulk shear stresses in the abutting materials. In the case of finite deformation, both the Lagrangian and Eulerian descriptions of the generalized Young–Laplace equations can also

8

H. L. Duan et al.

be obtained from the stationary condition of an energy functional (Huang and Wang, 2006). In addition to the generalized Young–Laplace Eq. (2.2), we also need the interface constitutive equations to solve the boundary value problems with the interface stress effect. Gurtin and Murdoch (1975) have given a linear constitutive equation for surface elasticity based on the principles of constitutive theory. As the creation of a surface or interface will usually induce a residual stress field in a body even in the absence of external loading, and this residual field will change when the body deforms, the determination of the mechanical response of the body in the presence of the surface/interface effect requires the solution of what is essentially a finite deformation problem (Huang and Wang, 2006; Huang and Sun, 2007). Recently, Huang and Wang (2006) derived the constitutive relations for hyperelastic solids with the surface/interface energy effect at finite deformation. Later, Huang and Sun (2007) conducted an infinitesimal analysis based upon this theoretical framework and derived the surface/interface elastic constants in terms of the surface/interface free energy. For a linearly elastic and isotropic surface, the Cauchy stress of the surface is (Gurtin and Murdoch, 1975; Huang and Wang, 2006) τ = γ0∗ 1 + λs (trεs ) 1 + 2μs εs ,

(2.4)

where γ0∗ 1 is the residual surface stress in the reference configuration, λs and μs are the Lamé constants of the surface, εs is the surface strain tensor, and 1 is the second-order unit tensor in a two-dimensional space. From the above equation, a linearized constitutive relation for the surface Piola–Kirchhoff stress of the first kind, which is used in the Lagrangian description, can be written as (Gurtin and Murdoch, 1975; Huang and Wang, 2006) Ss = γ0∗ 1 + λs + γ0∗ (trεs ) 1 + 2 μs − γ0∗ εs + γ0∗ u∇0s ,

(2.5)

where u∇0s is the displacement gradient of the surface in the reference configuration. It is clear that the Cauchy and the Piola–Kirchhoff stress tensors of the first kind are not the same even under the assumption of infinitesimal deformation. Note that the parameter γ0∗ includes a liquid-like surface tension term. The currently available values of γ0∗ for solids are usually much smaller than those of the surface elastic constants λs and μs (Miller and Shenoy, 2000; Dingreville and Qu, 2007). Therefore, without loss of the essence of surface elasticity, the effect of γ0∗ can be omitted to facilitate theoretical analysis. The omission of this term renders the Cauchy and the Piola–Kirchhoff surface stress tensors of the first kind identical, just as the bulk stress tensors, under the assumption of infinitesimal deformation.


9

Thus, when augmented with the thermoelastic coupling term, the thermoelastic constitutive relation of a linearly elastic and isotropic surface/interface can be expressed as (Murdoch, 1976, 2005) τ = 2μs εs + λs (trεs )1 − T D0 ,

(2.6)

where D0 is the stress-temperature tensor of the interface. For the isotropic interface D0 = d0 1, we assume that d0 = αs κs , where αs is the coefficient of thermal expansion (CTE) of the interface and κs = 2(μs + λs ). Note that the elastic moduli of the interface have different units from those of the bulk, whereas the CTEs of the interface and bulk material have the same units. For a coherent interface (Cahn, 1978; Rottman, 1988), the interface strain εs is equal to the tangential strain in the abutting bulk materials. In the rest of this article, the description of surface/interface stresses is based upon the constitutive relation (2.6). Eqs. (2.2) and (2.6) constitute the basic equations to analyze the surface/interface stress effect on the elastic properties of materials, and these equations describe the so-called interface stress model (ISM, Duan et al., 2005a,b).

2.2. Eshelby Formalism The Eshelby formalism (Eshelby, 1956, 1957, 1959) is fundamental to the solution of many problems in materials science, solid state physics, and mechanics of composites. In the terminology of Eshelby (1957) and Mura (1987), an inclusion denotes a subdomain in a homogeneous solid subjected to an eigenstrain; an inhomogeneity is a region with elastic properties distinct from those of the matrix. When an eigenstrain is given to an inhomogeneity, it is called an inhomogeneous inclusion. The Eshelby formalism refers to the following problems (Eshelby, 1956, 1957, 1959): the strain field in an inclusion subjected to an arbitrary uniform eigenstrain in an infinite elastic medium; the elastic field in an inhomogeneity in an infinite medium subjected to a prescribed arbitrary uniform remote stress; and strain energy in solids containing inhomogeneities. We shall present the results for these three problems for a spherical inclusion and inhomogeneity with interface stress effect. 2.2.1. Eshelby Tensors We consider first the spherical inhomogeneity problem with the interface stress effect. For an inhomogeneous inclusion, that is, an inhomogeneity embedded in an alien infinite medium is given a uniform eigenstrain, the Eshelby tensors Sk (x) (k = I, m) relate the total strains εk (x) in the inhomogeneity (k = I), denoted by

10

H. L. Duan et al.

I , and the matrix (k = m), denoted by m , to the prescribed uniform eigenstrain ε∗ in the inhomogeneity εk (x) = Sk (x) : ε∗ ,

(k = I, m), ∀x ∈ I + m ,

(2.7)

where x is the position vector. The displacement field u∗ in the inhomogeneity corresponding to the uniform eigenstrain ε∗ is u∗ = ε∗ · x, ∀x ∈ I .

(2.8)

The interface and boundary conditions for this problem are: uI + u∗ = um , (σ I − σ m ) · n = ∇S · τ um = 0,

at

,

|x| → +∞.

σ m = 0,

(2.9) (2.10)

We now outline the procedure for the solution of the inhomogeneous inclusion problem. Based on the basic equations mentioned above, the elastic solutions of the nanoinhomogeneities with arbitrary shape can be obtained by using the corresponding techniques. Here, we consider a spherical inhomogeneity of radius R embedded in an infinite medium as an example (Fig. 2.1). It is given an arbitrary uniform eigenstrain ε∗ . This elastostatic problem with the interface stress is solved using the principle of superposition, that is, we obtain the complete set of the components of the Eshelby tensors Sk (x) through the consideration of several particular eigenstrains. For this, we first solve the elastic field induced by ε∗zz = 1, and the Z

␪

⌫

r

Y

␸ p X m

Fig. 2.1 A spherical inhomogeneity in an infinite medium.


11

solution is given in the spherical coordinate system (r, θ, ϕ) (cf. (Fig. 2.1)). The axisymmetric elasticity problem for spherical domains can be solved in a general fashion in terms of functions of r multiplied by Legendre polynomials of θ. For the present problem, only a solution associated with Legendre polynomials n = 0, 2 is needed (Lur’e, 1964). It is expedient to split the displacement field into its dilatational part, k ukr = Fzz r+

Gkzz , r2

ukθ = ukϕ = 0,

(k = I, m),

(2.11)

and its deviatoric part, ukr = Urk P2 (cos θ), in which

ukθ = Uθk

dP2 (cos θ) , dθ

ukϕ = 0,

(k = I, m),

(2.12)

k k 2(5 − 4ν D )C k zz zz k r+ −3 4 , Urk (r) = 12νk Akzz r 3 + 2Bzz r2 r

k k 2(1 − 2ν D )C k zz zz k r+ + 4 . Uθk (r) = (7 − 4νk )Akzz r 3 + Bzz r2 r

(2.13)

(2.14)

k , C k , Dk , Here, P2 (cos θ) is the Legendre polynomial of order two. Akzz , Bzz zz zz k k Fzz , and Gzz are constants to be determined. The subscript zz of these constants indicates that they are solved for the eigenstrain ε∗zz = 0. For the inhomogeneous inclusion problem, these constants are determined from the condition to avoid a singularity at r = 0 inside the inhomogeneity and Eqs. (2.9) and (2.10). Inside the I , DI , and GI vanish; in the matrix (k = m), Am , Bm , inhomogeneity (k = I), Czz zz zz zz zz m and Fzz vanish. Due to the spherical shape of the inhomogeneity and linear property of the problem, the solution due to an arbitrary uniform eigenstrain ε∗ can be obtained from Eqs. (2.11)–(2.14) by superimposing the individual solutions for ε∗xx = 1, ε∗yy = 1, ε∗zz = 1, ε∗xy = 1, ε∗xz = 1, and ε∗yz = 1, respectively. The detailed procedures of the superposition can be found in Duan et al. (2005b). It is found that under ε∗xx = 1, ε∗yy = 1, ε∗zz = 1, ε∗xy = 1, ε∗xz = 1, and ε∗yz = 1, respectively, six constants AIpq (pq = xx, yy, zz, xy, xz, and yz) can be obtained, and they obey the following relation: AIxx = AIyy = AIzz = AIxy = AIxz = AIyz . Moreover, the conI , C m , Dm , F I , and Gm also obey their own respective identities. stants Bpq pq pq pq pq Therefore, for brevity, we introduce constants A, B, C, D, F , and G such that

A ≡ R2 AIpq ,

I B ≡ Bpq ,

C≡

m Cpq

R3

,

D≡

m Dpq

R5

,

I F ≡ Fpp ,

G≡

Gm pp R3

,

(2.15)

12

H. L. Duan et al.

where the subscript pairs pq = xx, yy, zz, xy, xz, and yz denote the eigenstrain cases ε∗xx = 1, ε∗yy = 1, ε∗zz = 1, ε∗xy = 1, ε∗xz = 1, and ε∗yz = 1, respectively. Thus, the repeated subscripts in Eq. (2.15) do not represent summation. Note that the last two expressions in Eq. (2.15) are applicable to pp = xx, yy, and zz only. Therefore, the total strain fields in the inhomogeneity and matrix are expressed in terms of the constants A, B, C, D, F , and G. In view of the geometrical and physical symmetry of the inhomogeneous inclusion problem under consideration, the Eshelby tensors in the two phases are transversely isotropic with any of the radii being an axis of symmetry. However, it should be noted that unlike the classical interior Eshelby tensor for an ellipsoidal inhomogeneity without the interface stress, the interior Eshelby tensor with interface stress is generally position dependent. Using the Walpole notation (Walpole, 1981) for transversely isotropic tensors, a fourth-order tensor Sk (r) with radial symmetry can be expressed as Sk (r) = S1k (r)E1 + S2k (r)E2 + S3k (r)E3 + S4k (r)E4 + S5k (r)E5 + S6k (r)E6 (2.16) or in a concise matrix form T Sk (r) = Sk (r)·E in which

Sk (r) = S1k (r) S2k (r) S3k (r) S4k (r) S5k (r) S6k (r) ,

E = E1 E2 E3 E4 E5 E6 ,

(2.17)

(2.18) (2.19)

where r(r = rn) is the position vector of the material point at which the Eshelby tensor is being calculated. n = ni ei is the unit vector along the radius passing through this point, and r is the distance from this point to the origin (the centre of the spherical inhomogeneity). ni are the direction cosines of r and i = 1, 2, 3 denote x-, y-, and z-directions, respectively. Skq (r) (q = 1, 2, . . . , 6) are functions of r, and Ep (p = 1, 2, . . . , 6) are the six elementary tensors (Walpole, 1981) 1 βij βmn , 2 = αij αmn , 1 = βim βjn + βjm βin − βij βmn , 2 1 βim αjn + βin αjm + βjm αin + βjn αim , = 2 = αij βmn ,

1 = Eijmn 2 Eijmn 3 Eijmn 4 Eijmn 5 Eijmn 6 Eijmn

= βij αmn ,

(2.20)

Theory of Elasticity at the Nanoscale where αij and βij are given by αij = ni nj ,

βij = δij − ni nj ,

13

(2.21)

and δij is the Kronecker delta. The (interior) Eshelby tensor in the inhomogeneous inclusion (I ) is given by Eq. (2.17) with SI (r) being ⎤T ⎡ 1 + B + 2F + 3(7 − 8νI )Ah2 ⎥ ⎢ 1 + 2B + F + 36νI Ah2 ⎥ ⎢ ⎥ ⎢ 2 ⎥ ⎢ 1 + 3B + 3(7 − 4νI )Ah ⎥ (2.22) SI (r) = ⎢ ⎢ 1 + 3B + 3(7 + 2ν )Ah2 ⎥ . I ⎥ ⎢ ⎥ ⎢ ⎦ ⎣ −B + F − 18νI Ah2 −B + F − 3(7 − 8νI )Ah2 In the matrix (m ), the exterior Eshelby tensor is again given by Eq. (2.17) with Sm (r) being ⎡ ⎤T 1 1 ⎢ 6D h5 + 2 [G − 2(1 + νm )C] h3 ⎥ ⎢ ⎥ ⎢ ⎥ ⎢ 12D 1 − 2 [G + 2(5 − 4νm )C] 1 ⎥ ⎢ 5 3 h h ⎥ ⎢ ⎥ ⎢ ⎥ 1 1 ⎢ ⎥ 3D 5 + 6(1 − 2νm )C 3 ⎢ ⎥ h h m ⎢ ⎥ . (2.23) S (r) = ⎢ ⎥ 1 1 ⎢ ⎥ −12D + 6(1 + ν )C m ⎢ ⎥ h5 h3 ⎢ ⎥ ⎢ 1 1 ⎥ ⎢ −6D − 2 [G − (5 − 4νm )C] ⎥ ⎢ h5 h3 ⎥ ⎢ ⎥ ⎣ 1 1 ⎦ −6D 5 + [G + 4(1 + νm )C] 3 h h In Eqs. (2.22) and (2.23), h = r/R, and 2η (4 − 5νm ) κsr + 2μrs η12 A= , B= , 3η11 3η11 (1 − 2νI ) 2 + κsr , F =− 3 η (1 + νI ) + (1 − 2νI ) 2 + κsr 5η2 (7 + 5νI ) + 4η (7 − 10νI ) 5 + 3κsr + μrs C=− , 6η11

3η2 (7 + 5νI ) + 4η (7 − 10νI ) 3 + (1 + νm ) κsr − (1 − 2νm ) μrs D=− , 3η11 η (1 + νI ) , G= (2.24) 3 η (1 + νI ) + (1 − 2νI ) 2 + κsr

14

H. L. Duan et al.

where

η11 = −2η2 (7 + 5νI ) (4 − 5νm ) + 7η −39 − 20κsr − 16μrs + 35νm η 9 + 5κsr + 4μrs + νI η 285 + 188κsr + 16μrs − 5νI νm η 75 + 47κsr + 4μrs − 4 (7 − 10νI ) 7 + 11μrs

+ 4 (7 − 10νI ) −κsr 5 + 4μrs + νm 5 + 4κsr + 13μrs + 5κsr μrs , (2.25)

η12 = 4 (7 − 10νI ) 7 + 11μrs + κsr 5 + 4μrs − νm 5 + 4κsr + 13μrs + 5κsr μrs + 7η 7 − 5νm + 5νm κsr − 4κsr + νI η 35 + 4κsr + 48μrs − 5νI νm η 5 + κsr + 12μrs , (2.26) and η = μI /μm with μI and μm being the shear moduli of the inhomogeneity and the matrix. κsr and μrs are two nondimensional parameters, κsr =

lκ , R

lκ =

κs , μm

μrs =

lμ , R

lμ =

μs , μm

(2.27)

lκ and lμ are two intrinsic length scales. It is noted that the Eshelby tensors are functions of lκ and lμ . To reveal the salient features of the Eshelby tensors (2.17) for the inhomogeneous inclusion with the interface stress that are absent in the classical Eshelby tensors, we present below the major components of the interior Eshelby tensor SI (r) in cartesian coordinates (for brevity, we drop the superscript I) 3A S1111 = F + 2B + 2 7(y2 + z2 ) − 6νI (−2x2 + y2 + z2 ) + 1, (2.28) R S1122 = F − B − S1212 =

3A 2 2 2 2 7y + 2ν (3x − 4y + z ) , I R2

1 3 3A 2 2 2 2 2 2 7(x + y + z ) + 2ν (x + y − 2z ) + . B+ I 2 2 2R2

(2.29) (2.30)

Some additional components can be obtained by simultaneous permutation of the subscripts (1, 2, 3) and coordinates (x, y, z); thus, S2222 and S3333 can be obtained from S1111 in (2.28), S2211 , S1133 , S2233 , S3311 , and S3322 from S1122 in (2.29), and S1313 and S2323 from S1212 in (2.30). Other components are as follows: ⎧ ⎫ ⎧ ⎫ ⎧ ⎫ ⎧ ⎫ xy ⎬ ⎨ S1222 ⎬ xy ⎬ ⎨ S1211 ⎬ ⎨ ⎨ A A = 6νI 2 −2yz , = 6νI 2 , (2.31) yz S S ⎩ 2311 ⎭ ⎭ ⎩ 2322 ⎭ ⎭ R ⎩ R ⎩ S1311 S1322 xz −2xz

Theory of Elasticity at the Nanoscale ⎫ ⎧ ⎫ ⎧ −2xy ⎬ ⎨ S1233 ⎬ A ⎨ = 6νI 2 , yz S ⎭ ⎩ 2333 ⎭ R ⎩ S1333 xz ⎧ ⎫ ⎫ ⎧ w ⎨ S1123 ⎬ A ⎨ 2⎬ S2223 = 3 2 yz w1 , ⎩ ⎭ ⎭ ⎩ R S3323 w1

⎧ ⎫ ⎧ ⎫ w ⎨ S1112 ⎬ A ⎨ 1⎬ S2212 = 3 2 xy w1 , ⎩ ⎭ ⎩ ⎭ R S3312 w2 ⎧ ⎫ ⎧ ⎫ w ⎨ S1113 ⎬ A ⎨ 1⎬ S2213 = 3 2 xz w2 , ⎩ ⎭ ⎩ ⎭ R S3313 w1

where w1 = −7 + 16νI , w2 = −7 + 10νI ⎧ ⎫ ⎧ ⎫ xy ⎨ S2313 ⎬ A ⎨ ⎬ = 9νI 2 yz , S ⎩ 1213 ⎭ R ⎩ ⎭ xz S1223

15

(2.32)

(2.33)

(2.34)

with S1323 = S2313 , S1312 = S1213 , S2312 = S1223 . In the above expressions (2.28)–(2.34), the constants A, B, and F are given in (2.24), where F is contributed by the dilatational solution (2.11) and A and B by the deviatoric solution (2.12)–(2.14). The Eshelby tensor in the inhomogeneous inclusion (and in the matrix) is size dependent through the two nondimensional parameters κsr and μrs . It is clearly seen from the expressions in Eqs. (2.22) and (2.28)–(2.34) that the interior Eshelby tensor is, in general, not uniform for an inhomogeneous inclusion with the interface stress effect; it is a quadratic function of the position coordinates. The solution without the interface stress effect can be obtained by setting κs = 0 and μs = 0 or letting R → ∞. The interior Eshelby tensor is constant in this case. Under dilatational eigenstrain ε∗ = 0 I(2) , the total strain in the inhomogeneous inclusion is given by εI = 0 SI : I(2) . It can be verified that SI : I(2) is a constant tensor even in the presence of the interface stress effect, and thus the stress field in the inhomogeneous inclusion is uniform, confirming the result of Sharma et al. (2003) for a dilatational eigenstrain. Furthermore, when the elastic constants of the inhomogeneity are the same as those of the matrix, namely η = 1 and νI = νm , the inhomogeneity becomes an inclusion. In this case, for a dilatational eigenstrain ε∗ = 0 I(2) , the strain fields in the inclusion and the matrix reduce to those in the paper of Sharma and Ganti (2004). 2.2.2. Stress Concentration Tensors We shall next consider the problem where a spherical inhomogeneity with the interface stress is embedded in an infinite elastic medium with a prescribed arbitrary uniform remote stress field σ 0 . The interior stress concentration tensor for this problem (i.e., inside the inhomogeneity) has recently been given by Duan et al. (2005b). (We use the terminology stress concentration tensor rather than Eshelby

16

H. L. Duan et al.

tensor because we are not solving the inhomogeneity problem using the Eshelby equivalent inclusion approach. This approach loses its elegance in the presence of a surface stress, and the inhomogeneity problem is better solved directly). Here, we shall present both the interior and exterior stress concentration tensors for completeness. The stress concentration tensors Tk (x) (k = I, m) relate the stresses σ k (x) in the two phases to the prescribed uniform remote stress σ 0 , that is, σ k (x) = Tk (x) : σ 0 ,

(k = I, m), ∀x ∈ I + m .

(2.35)

The interface and boundary conditions for this problem are: uI = um , (σ I − σ m ) · n = ∇S · τ um = u0 ,

σm = σ0,

at

(2.36)

,

|x| → +∞.

(2.37)

As for the inhomogeneous inclusion problem in the previous section, this inhomogeneity problem under remote loading is also solved by the principle of 0 = 1 are superposition (Duan et al., 2005b). For example, the solutions under σzz still given by (2.11)–(2.14) with the constants determined by interface and boundary conditions (2.36), (2.37) and the condition to avoid a singularity at r = 0. I , DI , and GI vanish; in the matrix (k = m), In the inhomogeneity (k = I), Czz zz zz m m Am zz vanishes, and Bzz and Fzz are determined from the corresponding remote 0 = 1, σ 0 = 1, σ 0 = 1, loading conditions in Eq. (2.37). It is found that under σxx yy zz 0 0 0 I I σxy = 1, σxz = 1, and σyz = 1, respectively, Axx = Ayy = AIzz = AIxy = AIxz = I , C m , Dm , F I , and Gm also obey their own respective AIyz . The constants Bpq pq pq pq pq identities. Therefore, we define constants A, B, C, D, F, and G such that A ≡ R2 μI AIpq , D ≡ μm

m Dpq

R5

,

I B ≡ μI Bpq ,

C ≡ μm

2(1 + νI ) I F≡ , μI Fpp (1 − 2νI )

m Cpq

R3

,

G ≡ μm

Gm pp R3

(2.38) .

As before, the subscript pairs pq = xx, yy, zz, xy, xz, and yz denote the remote 0 = 1, σ 0 = 1, σ 0 = 1, σ 0 = 1, σ 0 = 1, and σ 0 = 1, respecstress cases σxx yy zz xy xz yz tively. Again, the last two expressions in Eq. (2.38) are applicable to pp = xx, yy, and zz only. Therefore, the total stress fields in the inhomogeneity and matrix are expressed in terms of the constants A, B, C, D, F, and G. The stress concentration tensors for the spherical inhomogeneity with the interface stress effect can be expressed as (Duan et al., 2005a) T Tk (r)·E Tk (r) =

(k = I, m)

(2.39)


17

in which Tk (r) =

T1k (r) T2k (r) T3k (r) T4k (r) T5k (r) T6k (r) .

(2.40)

In the inhomogeneity (I ), the stress concentration tensor is given by Eq. (2.39) with TI (r) being ⎤T ⎡ 2B + 2F + 6(7 + 6νI )Ah2 ⎥ ⎢ 4B + F − 12νI Ah2 ⎥ ⎢ ⎥ ⎢ 2 ⎥ ⎢ 6B + 6(7 − 4ν )Ah I ⎥ . (2.41) TI (r) = ⎢ ⎥ ⎢ 2 6B + 6(7 + 2νI )Ah ⎥ ⎢ ⎥ ⎢ ⎦ ⎣ −2B + F + 6νI Ah2 −2B + F − 6(7 + 6νI )Ah2 In the matrix (m ), the stress concentration tensor is again given by Eq. (2.39) with Tm (r) being ⎤T ⎡ 1 1 [G 1 + 12D + 4 − 2(1 − 2ν )C] m ⎢ h5 h3 ⎥ ⎥ ⎢ ⎥ ⎢ ⎢ 1 + 24D 1 − 4 [G + 2(5 − ν )C] 1 ⎥ m ⎥ ⎢ h5 h3 ⎥ ⎢ ⎥ ⎢ 1 1 ⎥ ⎢ 1 + 6D 5 + 12(1 − 2νm )C 3 ⎥ ⎢ ⎥ ⎢ h h m ⎥ ⎢ (2.42) T (r) = ⎢ ⎥ 1 1 ⎥ ⎢ 1 − 24D + 12(1 + ν )C m ⎥ 5 ⎢ 3 h h ⎥ ⎢ ⎥ ⎢ 1 ⎥ ⎢ −12D − 4 [G − (5 − ν )C] 1 m ⎥ ⎢ h5 h3 ⎥ ⎢ ⎢ 1 1 ⎥ ⎦ ⎣ −12D 5 + 2 [G + 4(1 − 2νm )C] 3 h h in which 5η(1 − νm )(κsr + 2μrs ) 5ηη21 (1 − νm ) , B= , 2η11 2η11 η(1 + νI )(1 − νm ) 5η23 F= , C= , η22 24η11 η23 + 4(7 − 10νI )(1 − νm )(κsr + 2μrs ) D= , 4η11

−η(1 + νI )(1 − 2νm ) + (1 − 2νI ) 1 − κsr + νm (1 + 2κsr ) G= , 6η22 A=

(2.43)

18

H. L. Duan et al.

where η11 has been given in Eq. (2.25), and

η21 = − η(7 + 5νI ) − 8νI (5 + 3κsr + μrs ) + 7(4 + 3κsr + 2μrs ) , (2.44)

η22 = (1 + νm ) η(1 + νI ) + (1 − 2νI )(2 + κsr ) , (2.45) η23 = 2η2 (7 + 5νI ) − 4(7 − 10νI )(2 + κsr )(1 − μrs ) +

+ η 7(6 + 5κsr + 4μrs ) − νI (90 + 47κsr + 4μrs ) .

(2.46)

The stress concentration tensors in the inhomogeneity and matrix exhibit the same features as the interior and exterior Eshelby tensors in an inhomogeneous inclusion, namely they are size- and position dependent. 2.2.3. Eshelby formula The Eshelby formula gives the strain energy in solids containing inhomogeneities (Eshelby, 1956). It is of great value in heterogeneous material analysis because it reduces the usual volume integrations for calculating strain energy to surface integration. Consider an inhomogeneity in an elastic matrix. Such a problem arises, for example, in the prediction of the effective moduli of heterogeneous materials which we shall consider later in this chapter. Here, we give the Eshelby formula for the nano-inhomogeneity. Denote the external surface of the matrix by S and the interface between the inhomogeneity and matrix by . Under uniform strain boundary condition u(S) = ε0 · x, where x is the position vector and ε0 is a constant strain tensor, the Eshelby formula with the interface stress effect can be obtained according to the same procedures as those to obtain the classical Eshelby formula without interface stress effect, that is, 1 n · σ m · u0 − u · σ 0 · n d U = U0 + (2.47) 2 in which 1 U0 = 2

σ 0 : ε0 dV.

(2.48)

V

Here, U is the elastic strain energy in the heterogeneous material, and σ m and u are the stress and displacement, respectively, at with the superscript “m” signifying that the stress is to be evaluated on the matrix side. σ 0 and u0 , however, denote the stress and displacement, respectively, in the homogeneous body of volume V made of the matrix only. When σ I = σ m , Eq. (2.47) reduces to the classical Eshelby formula, 1 (2.49) U = U0 + n · σ · u0 − u · σ 0 · n d. 2


19

Under uniform stress boundary condition (S) = σ 0 · N, where N is the outward unit normal vector to S and σ 0 is a constant stress tensor, the Eshelby formula with the interface stress effect is 1 U = U0 + n · σ 0 · u − u0 · σ m · n d. (2.50) 2 When σ I = σ m , Eq. (2.50) reduces to the classical Eshelby formula, 1 U = U0 + n · σ 0 · u − u0 · σ · n d. 2

(2.51)

It is noted that the difference between the classical Eshelby formula (Eq. (2.49) or Eq. (2.51)) and the Eshelby formula with interface stress effect (Eq. (2.47) or Eq. (2.50)) is that there is stress discontinuity across the interface due to the interface stress effect. Therefore, for the composites with nano-inhomogeneities, the stress σ m in the Eshelby formula Eq. (2.47) (or Eq. (2.50)) should be evaluated on the matrix side. 3. Application of Eshelby Formalism for Nano-inhomogeneities

3.1. Stress Concentration Factor of a Spherical or Circular Nanovoid Consider a spherical nanovoid in an infinite matrix under an axisymmetric 0 = T and σ 0 = σ 0 = χ T . Without loss of generality, loading at infinity with σzz xx yy the triaxiality parameter χ is allowed to range from zero to one so that the loading conditions change from uniaxial tension (compression) to hydrostatic tension (compression). However, before solving the stress concentration due to a spherical or circular nanovoid, we examine some features of the stress field in a generic spherical inhomogeneity. The stress concentration tensor in the spherical inhomogeneity is not uniform because of the presence of the terms involving AI in Eqs. (2.13) and (2.14). Here, we use AIaxis to denote this constant under axisym0 = T and σ 0 = σ 0 = χ T . Without going into details, it can metric loading σzz xx yy be shown that for the axisymmetric remote loading under consideration, AIaxis is given by 5T(1 − χ)(1 − νm )(κsr + 2μrs ) . (3.1) AIaxis = 2R2 μm η11 It is interesting to note that uniform stress fields appear when AIaxis vanishes. This can happen for a finite size inhomogeneity when: (i) the surface stress effect is absent, κs = μs = 0, (ii) the remote loading is hydrostatic, χ = 1 (confirming

20

H. L. Duan et al.

again the results of Sharma et al. (2003)), and (iii) η → ∞, which is the case if the inhomogeneity is infinitely rigid in comparison with the matrix. In all other cases, the stress field inside the inhomogeneity and outside it is not uniform. For a spherical nanovoid, the normalized hoop stress at the boundary of the 0 = T and σ 0 = σ 0 = χ T is given by void under σzz xx yy σθθm 3 [4 − 5νm + 3χ − 5(1 − χ) cos 2θ] (1 + 2χ)(1 − νm )κsr = − − T 2(7 − 5νm ) 2(1 + νm )(2 + κsr ) −

5(1 − χ)(1 − νm ) (M1 + 3N1 cos 2θ), 8H1 (7 − 5νm )

(3.2)

with

M1 = 6μrs (−5 + 19νm ) + κsr 1 − 16μrs + νm (7 + 50μrs ) ,

N1 = 13 + 16μrs − 5νm (1 − 2μrs ) κsr + 2(29 + 5νm )μrs ,

(3.3)

H1 = −7 + 5νm + μrs (13νm − 11) + κsr (5νm μrs − 4μrs + 4νm − 5). The first term on the right-hand side of Eq. (3.2) is the classical solution, and the other terms are due to the surface stress effect. κsr and μrs are given by Eq. (2.27). Following the same procedure, the normalized hoop stress at the boundary of a 0 = T and circular nanovoid in an infinite plate (for the plain stress case) under σxx 0 σyy = χT can be shown to be σφφm (1 + χ)χsr 6χsr (1 − χ) cos 2φ = 1 + χ − 2(1 − χ) cos 2φ − + , T (1 + νm )(4 + χsr ) 4 + 3χsr + νm (4 + χsr ) (3.4) where χsr = κsr + 2μrs . The polar coordinate system (ρ, φ) is used with the ρφplane perpendicular to the voids. Again, the first term on the right-hand side of Eq. (3.4) is the classical solution, and the other terms are due to the surface stress effect. The variation of the maximum normalized hoop stress at the boundary of a spherical nanovoid (at the equator, θ = π/2) is shown in Fig. 3.1 for aluminium (with bulk modulus κm = 75.2 GPa and Poisson ratio νm = 0.3). The free surface properties are taken from Miller and Shenoy (2000) and Sharma et al. (2003). Two sets of surface moduli are used, namely A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1]. It is seen from Fig. 3.1 that the stress concentration decreases (increases) with increasing void size due to the surface stress effect until it reaches the classical solution (without the surface stress effect) which is independent of the void size. The effect of the surface stress on the stress concentration also depends on the stress triaxiality. The lower the stress triaxiality, the greater the

Theory of Elasticity at the Nanoscale 2.8

A, x 5 0 B, x 5 0 C, x 5 0

s␪␪m/ T

2.4

A, x 5 0.5 B, x 5 0.5 C, x 5 0.5

21

A, x 5 1 B, x 5 1 C, x 5 1

2.0 1.6 1.3

1

10

20

30 R (nm)

40

50

Fig. 3.1 Stress concentration as a function of surface properties and spherical void radius for different stress triaxialities. In Fig. 2.1, “A” and “B” denote the solutions for the two sets of surface properties, and “C” the classical solution without the surface stress effect. Reprinted from Duan et al. (2005a) with acknowledgment to The Royal Society, 6–9 Carlton House Terrace, London SW1Y 5AG, England.

stress concentration. The surface stress effect on the stress concentration becomes negligible for void radius larger than 50 nm under uniaxial tension (χ = 0), while under hydrostatic loading (χ = 1), the surface stress effect is already negligible for void radius larger than 25 nm.

3.2. Strain Fields in QDs With Multi-shell Structures and in Alloyed QDs The behavior of electronic devices made of alloyed QDs (e.g., Inx Ga1−x As) or QDs with a multi-shell structure (e.g., CdS/HgS/CdS/HgS/CdS, ZnS/CdSe) is strongly affected by their enriched but nonuniform composition. It has been demonstrated that the assessment of the composition profiles and strains is important to both the identification of the dominant growth mechanisms and the modelling of the confining potential of QDs (Rosenauer and Gerthsen, 1999; Malachias et al., 2003; Spencer and Blanariu, 2005). In the following, we assume that the lattice constants or the thermal expansion coefficients of QDs with multi-shell structures or alloyed QDs obey Vegard’s law (Vegard, 1921) and analyze the strain distribution in and around the QDs. Moreover, the critical sizes of dislocation-free QDs will be determined. 3.2.1. Strain Distributions in QDs with Multi-shell Structures First, we consider a spherical QD with a multi-shell structure embedded in an infinite elastic matrix. Let phase 1 denote the innermost core, hereinafter referred to as the particle, and let phase i refer to the shell bounded by the concentric and spherical surfaces with radii ri and ri+1 (i ∈ (1, M)), respectively. Let 1 , k

22

H. L. Duan et al.

(k = 2, . . . i, . . . , M), and M+1 denote the regions occupied by the particle, the multi-shells, and the matrix, respectively. The subscripts k (k = 1, 2, . . . i, . . . , M, M + 1) are used to denote the quantities in the regions k , respectively. The particle, the multi-shells, and the matrix are homogeneous, linearly elastic, and isotropic, characterized by bulk modulus κk , shear modulus μk , and Poisson ratio νk (k = 1, 2, . . . i, . . . , M, M + 1). As stated above, the large ratio of surface/interface atoms to the bulk can have a profound effect on the properties of nanostructures, and this effect can be described by the classical continuum model with consideration of the interface stress effect. Moreover, the strains induced by the mismatch of the lattice constants and CTE in the spherical QD and its multi-shell structure can be treated as eigenstrains (Gosling and Willis, 1995; Rockenberger et al., 1998). Therefore, when uniform eigenstrains ε∗i (i = 1, 2, . . . , M) are prescribed in the particle and the multi-shells, the interface conditions for this problem can be expressed as ui + ε∗i · x = ui+1 + ε∗i+1 · x, (σ i − σ i+1 ) · m = ∇S · σ s , uM+1 = 0, σ M+1 = 0 at |x| → +∞,

(3.5)

where m is the unit normal vector to the interface between the ith and (i + 1)th phases, ∇S · σ s denotes the interface divergence of the interface stress tensor σ s . The interface stress σ s depends on the state of the elastic strain εs (Streitz et al., 1994; Bottomley and Ogino, 2001) via the constitutive relation (2.4) or (2.6). However, the interface elastic moduli are currently not available for QD materials. Thus, we simply consider the effect of a constant interface stress, σ s0 , and/or a constant surface stress, τ s , in this section. When uniform eigenstrains ε∗i (i = 1, 2, . . . , M) are prescribed in the particle and the multi-shells, then according to the Eshelby formalism above, the elastic strains εk (x) in the particle (k = I), the multi-shells (k = 2, 3, . . . , M), and the matrix (k = M + 1) can be expressed as εk = Ski : ε∗i − ε∗k + Hk (σ s0 )

(k = 1, 2, . . . , M + 1).

(3.6)

It is noted that ε∗M+1 = 0 in the above equation. Ski is the Eshelby tensor in the kth phase, which relates the uniform eigenstrain ε∗i prescribed in the ith phase to the strain induced in the kth phase (Eshelby, 1957). Thus, the repeated subscript i in Eq. (3.6) indicates summation from 1 to M. Hk (σ s0 ) is the strain tensor due to residual interface stress σ s0 . Ski satisfying the conditions (3.5) can be determined following the same procedure as that for obtaining Eshelby tensor Sk for spherical nano-inhomogeneity described above. After determining the Eshelby tensor Ski in the core and multi-shells, the elastic fields in them can be determined from Eq. (3.6).


23

In the following, we consider a free-standing spherical QD consisting of a core and concentric multi-shells of nanometer size. Besides the uniform eigenstrains ε∗i (i = 1, 2, . . . , M − 1) prescribed in the particle and the multi-shells, we also assume that an isotropic surface stress vector τ s (τ s = τ s 1, we distinguish it from the interface stress σ s ) acts on the outer surface of this QD. Then the elastic strains in the core and the multi-shells are εk = Ski : ε∗i − ε∗k + Hk (τ s , σ s0 )

(k = 1, 2, . . . , M),

(3.7)

where Hk (τ s , σ s0 ) is the strain tensor due to interface stress σ s0 and isotropic surface stress τ s . Here, the procedures to obtain Ski are similar to those used to obtain the Eshelby tensors for the embedded spherical QDs with multi-shell structures mentioned above. However, the interface and boundary conditions for this case are ui + ε∗i · x = ui+1 + ε∗i+1 · x, (σ i − σ i+1 ) · N = ∇S · σ s , (3.8) σrr = 2τ s /rM at r = rM . Note that ε∗M = 0 in the present case and i ∈ (1, M − 1) in Eqs. (3.7) and (3.8). Moreover, Eqs. (3.6) and (3.7) can apply to arbitrary uniform eigenstrains ε∗i prescribed in the core and multi-shells. For QD structures with a uniform composition, the mismatch of the lattice constants or thermal expansion coefficients of different constituents can induce an initial misfit strain. According to the definitions of an embedded QD (Gosling and Willis, 1995) and a free-standing core-shell particle (Rockenberger et al., 1998), the misfit strains arising from the different lattice constants and the thermal expansion coefficients between different phases are, respectively, ε∗m0 =

ain − aex , aex

ε∗tm0 = (αin − αex )T,

(3.9)

where ain , aex and αin , αex are the lattice constants and the thermal expansion coefficients of the interior and exterior phases, respectively. T is the temperature difference. For example, the misfit strain due to the mismatch of the lattice constants of the CdTe(core)/CdS(shell) structure is 11.6%, and that of ZnS(core)/CdS(shell) is −7.0%. 3.2.2. Strain Distributions in Alloyed QDs The expressions in Eq. (3.9) are the so-called Vegard’s law (Vegard, 1921). Note that Vegard’s law for alloyed materials is a linear function: Ealloy = xEA + (1 − x)EB , where EA , EB , and Ealloy are the respective properties of pure A, pure B, and the alloy Ax B1−x , and x is the fraction of one ingredient in a material point (Bailey and Nie, 2003). For example, experiments have shown that the lattice

24

H. L. Duan et al.

constant of the nonuniform QD (Znx Cd1−x S) exhibits a nearly linear relation with the Zn content x, which is consistent with Vegard’s law (Zhong et al., 2003; Li et al., 2005). To reveal the profound effect of a nonuniform composition on the stress state of a QD, consider, for simplicity, a spherical alloyed QD embedded in an infinite matrix. The analytical method is equally applicable to QDs of other shapes, sizes, and composition profiles. We assume that a spherical alloyed QD has a spherically symmetric composition, that is, the nonuniform composition is a function of the radial coordinate r only. Therefore, the misfit eigenstrain ε∗ (r) induced by the mismatch of the lattice constants and the thermal expansion coefficients can be expressed as ε∗ (r) = ε∗rr (r)er ⊗ er + ε∗θθ (r)(eθ ⊗ eθ + eϕ ⊗ eϕ ),

(3.10)

where er , eθ , and eϕ are the local unit base vectors in the spherical coordinate system, and ε∗rr (r) and ε∗θθ (r) are the misfit strains in the radial and tangential directions, respectively. According to Vegard’s law (1921), the misfit strains induced by the mismatch in the lattice constants and those by the mismatch in the thermal expansion coefficients are (Duan et al., 2006a), respectively, ε∗rr (r) = cr (r)ε∗m0 , ε∗θθ (r) = cθ (r)ε∗m0 , ε∗rr (r) = cr (r)ε∗tm0 , ε∗θθ (r) = cθ (r)ε∗tm0 , where ε∗m0 and ε∗tm0 are given by Eq. (3.9). cr and cθ are the concentrations of the ingredient at the location r in the radial and tangential directions. If cr ≡ 1 and cθ ≡ 1, Eq. (3.10) reduces to that for a uniform composition. We assume that the elastic constants of the alloyed QD are uniform. This is a reasonable assumption because the alloyed semiconductor QDs usually contain compounds (e.g., InAs/GaAs, CdTe/CdSe) with nearly identical elastic constants, and it has been validated by comparing isotropic and anisotropic solutions for semiconductor materials (Faux and Pearson, 2000). We begin with the total displacement vector u∗ in the free-standing QD induced by the eigenstrain ε∗ij . According to the theory of infinitesimal elasticity, cf. Eq. (2.1), the governing equation to obtain u∗ is 1 Cijkl u∗k,lj − ε∗kl,j = 0,

(3.11)

1 is the elastic modulus where the eigenstrains ε∗ij (x) are given in Eq. (3.10), and Cijkl tensor of the QD. When the variations of cθ (r) and cr (r) are known, the only nonvanishing component of the displacement vector u∗ , viz. u∗r (r), can be easily determined by Eqs. (3.10) and (3.11). In the following, we will consider the special case of cθ (r) = cr (r) = x(r). Substituting Eq. (3.10) into Eq. (3.11), it follows that the only nonvanishing component


25

of the displacement vector u∗ , viz. u∗r (r), must satisfy the equation r2

∂2 u∗r ∂u∗ (1 + ν1 ) ∗ 2 ∂x + 2r r − 2u∗r − ε r = 0, 2 ∂r (1 − ν1 ) m0 ∂r ∂r

(3.12)

where ν1 is the Poisson ratio of the core. Therefore, Eq. (3.12) and the tractionfree condition at the outer boundary of the free core constitute the basic equations to find u∗r (r). For a known variation of x, for example, it could vary in a linear, logarithmic, or exponential manner with r, u∗r (r) can be easily determined. In particular, if x(r) in Eq. (3.10) is assumed to be a linear function in the radial coordinate r r (3.13) x(r) = k0 + k1 , rco where k0 and k1 are two constants, and rco denotes the radius of the nonuniform core, then the corresponding u∗r (r) is given by Eq. (3.12) and the traction-free condition at the outer boundary of the free core (1 − 2ν1 )k1 ε∗m0 k1 (1 + ν1 )r 2 ε∗m0 + . (3.14) u∗r (r) = r k0 ε∗m0 + 2(1 − ν1 ) 4rco (1 − ν1 ) When the alloyed QD is embedded in an infinite medium (relative to its size), the constraint imposed by the exterior medium will induce an additional displacement field, identified by superscript 1 in the QD and superscript 2 in the matrix: u1r = F1 r, u2r = G2 /r 2 . The constants F1 and G2 are determined from the following interface conditions: u2r = u1r + u∗r |r=rco ,

2 1 σrr − σrr =

2σ0s . rco

(3.15)

Then the elastic strains in the embedded spherical alloyed QD can be determined. The free-standing QD is assumed to be composed of a nonuniform core and a uniform shell with the nonuniform eigenstrain ε∗ prescribed in the core. Also, an isotropic surface stress τ s = τ s 1 is exerted at the outer surface of the shell. The procedure to obtain the solution due to ε∗ is similar to that for the embedded spherical alloyed QD. Let us compare the elastic strain distribution in the free-standing alloyed QD Znx Cd1−x S with that in the free-standing QD with multishells CdS/ZnS/CdS (M = 3). The elastic constants of bulk ZnS and CdS are as follows: ZnS, bulk modulus 81.6 GPa, Poisson’s ratio 0.4; and CdS, bulk modulus 62.3 GPa, Poisson’s ratio 0.4. The lattice constants of ZnS and CdS are a = 5.409 Å, a = 5.815 Å, respectively. Therefore, the misfit strain due to the mismatch of the lattice constants of ZnS(core)/CdS(shell) is ε∗m0 = −7.0%. We assume that the surface stress is τ s = 1 N/m for the free-standing QD. We consider

26

H. L. Duan et al.

two cases for Znx Cd1−x S: Case I: k0 = 0.8, k1 = −0.4; Case II: k0 = 1, k1 = 0, and the radii of the core and shell are rco = 9 nm and rsh = 12 nm, respectively. Case II corresponds to a uniform core. For CdS/ZnS/CdS, the radii of the core and two shells are rco1 = 6 nm, rsh1 = 9 nm, rsh2 = 12 nm, respectively. The normalized elastic strain (εzz /ε∗m0 ) and the normalized biaxial strain (εb /ε∗m0 ) are shown in Figs. 3.2 and 3.3. It can be seen that the distributions of the elastic strains are strongly dependent on the compositions and structures of the QDs, and are different for Znx Cd1−x S and CdS/ZnS/CdS (M = 3). Note that the elastic strain in the core (−1 ≤ z/rco ≤ 1.0) of CdS/ZnS/CdS is uniform, whereas the strain in the core of Znx Cd1−x S is nonuniform. Three factors, namely the particle size, composition, and internal structure, have been used to achieve continuous tuning of the optical properties of QDs (Bailey and Nie, 2003; Liang et al., 2005). From Figs. 3.2 and 3.3 and the above analysis, it can be seen that the strain can be modified by adjusting the composition via the two parameters k0 and k1 in the Inx Ga1−x As/GaAs and CdTex Se1−x QD systems. Likewise, the strain in QDs with multi-shells can be modified by adjusting the thickness and the number (M) of the shells according to Eqs. (3.5)–(3.8) (Figs. 3.2, 3.3). Bailey and Nie (2003) have shown that continuous tuning of the optical properties of the CdTex Se1−x QDs can be achieved by changing the composition (Se:Te molar ratio) and the internal structure without changing the particle size. The composition changes the strain, and the strain affects the optical properties of CdTex Se1−x . Moreover, Bailey and Nie (2003) indicated that the tuning of the optical properties through a change in the composition and the internal structures is more advantageous than through a change in the particle size in some applications such as nanoelectronics, superlattice structures, and biological labeling. 3 Case I, Znx Cd12x S

2 εzz /ε*m 0

Case II, Znx Cd12x S

1

CdS/ZnS/CdS

0 21 22 21.3 21.0

20.5

0.0 z /rco

0.5

1.0 1.3

Fig. 3.2 Distribution of normalized elastic strain εzz /ε∗m0 in the free-standing QDs Znx Cd1−x S and CdS/ZnS/CdS subjected to an eigenstrain ε∗ in Eq. (3.10) and a surface stress τ s . Case I: k0 = 0.8, k1 = −0.4; Case II: k0 = 1, k1 = 0. Reprinted from Duan et al. (2006a) with acknowledgment to IOP Publishing Ltd, Dirac House, Temple Back, Bristol BS1 6BE, England.


27

0.0

εb /ε*m 0

21.5

Case I, Znx Cd12x S Case II, Znx Cd12x S

23.0

CdS/ZnS/CdS

24.5 26.0 21.3 21.0

20.5

0.0 z /rco

0.5

1.0 1.3

Fig. 3.3 Distribution of normalized biaxial strain εb /ε∗m0 in the free-standing QDs Znx Cd1−x S

and CdS/ZnS/CdS subjected to an eigenstrain ε∗ in Eq. (3.10) and a surface stress τ s . Case I: k0 = 0.8, k1 = −0.4; Case II: k0 = 1, k1 = 0. Reprinted from Duan et al. (2006a) with acknowledgment to IOP Publishing Ltd, Dirac House, Temple Back, Bristol BS1 6BE, England.

3.3. Compatible Composition Profiles and Critical Sizes of Alloyed QDs For the considered alloyed spherical QD, the only nonvanishing equation of compatibility of misfit eigenstrains ε∗rr and ε∗θθ represented in Eq. (3.10) reduces to an equation relating the radial and tangential alloy composition profiles r

∂cθ (r) + cθ (r) = cr (r). ∂r

(3.16)

Eq. (3.16) is identically satisfied when the composition is uniform, but it imposes restrictions on cr and cθ when the composition is nonuniform. The strain fields induced by nonuniform composition profiles that meet Eq. (3.16) are vastly different from those induced by profiles that violate this condition, howsoever slightly (e.g., cr (r) = cθ (r) = x(r) in Eq. (3.13)). Thus, the compatibility condition (Eq. (3.16)) provides a theoretical basis for designing the composition profile of an alloyed QD and for estimating its lattice deformation. Without loss of generality, we consider the following two cases of linear composition: Case I: compatible composition profile satisfying Eq. (3.16), for example, cθ (r) = k0 + k1 r/rco , cr (r) = k0 + 2k1 r/rco , where k0 and k1 are two constants and rco is the radius of the QD; Case II: composition profile not satisfying Eq. (3.16), cθ (r) = cr (r) = k0 + k1 r/rco (Eq. (3.13)). The expressions of the elastic strain in the alloyed QD and the uniform matrix due to the misfit eigenstrains for Cases I and II can be found in the papers of Duan et al. (2006a,b). It is found that the strain field in the alloyed QD is uniform irrespective of the composition profile provided the nonuniform misfit eigenstrains satisfy the compatibility

28

H. L. Duan et al.

equation (cf., Fig. 3.4 for Case I), but not otherwise (cf., Fig. 3.5 for Case I; Duan et al., 2006a,b). Strains play a very important role in the nanofabrication technology, and strain relaxation through the formation of dislocations is highly undesirable for the εzz /ε*m0

2

z /rco

1 0 21 22 22

21

0

1

2

0.18 0.155 0.13 0.105 0.08 0.055 0.03 0.005 20.02 20.045 20.07 20.095 20.12 20.145 20.17 20.195 20.22 20.245 20.27 20.295 20.32 20.345 20.37 20.395 20.42

y/rco

Fig. 3.4 Distribution of normalized elastic strain εzz /ε∗m0 in the embedded QD (Inx Ga1−x As/GaAs) subjected to nonuniform eigenstrains ε∗ satisfying the compatibility equation (Case I, k0 = 0.8; k1 = −0.4). Reprinted from Duan et al. (2006b) with acknowledgment to American Physical Society. εzz /ε*m0

2

z /rco

1 0 21 22 22

21

0 y/rco

1

2

0.18 0.155 0.13 0.105 0.08 0.055 0.03 0.005 20.02 20.045 20.07 20.095 20.12 20.145 20.17 20.195 20.22 20.245 20.27 20.295 20.32 20.345 20.37 20.395 20.42

Fig. 3.5 Distribution of normalized elastic strain εzz /ε∗m0 in the embedded QD (Inx Ga1−x As/GaAs) subjected to nonuniform eigenstrains ε∗ not satisfying the compatibility equation (Case I, k0 = 0.8; k1 = −0.4). Reprinted from Duan et al. (2006b) with acknowledgment to American Physical Society.


29

performance of semiconductor devices (e.g., Zhang, 1995; Tersoff, 1998; Chen et al., 2003). Kolesnikova and Romanov (2004) obtained the critical radii of a spherical QD and a cylindrical quantum wire (QW) with uniform composition by considering the energy of nucleation of circular prismatic dislocation loops from a spherical QD and a cylindrical QW. We calculate the critical radii of the spherical alloyed QD at which the nucleation of a misfit prismatic dislocation (MD) loop (cf. Fig. 1 in Duan et al. (2006b)) becomes energetically favourable. We will again study the effect of the compatibility of misfit strains. The condition for the nucleation of an MD loop is (Kolesnikova and Romanov, 2004), EL + WIL ≤ 0,

(3.17)

where EL is the elastic energy of the prismatic dislocation loop and WIL is the interaction energy between it and the QD. EL of a dislocation loop of radius rL and Burgers vector of magnitude b in infinite space is (Kolesnikova and Romanov, 2004) 8αrL μb2 rL ln −2 , (3.18) EL ≈ 2(1 − ν) b where α is a parameter that takes into account the energy of the dislocation core. WIL is 1 1 ε∗L σ dV = − (−b)σzz dS, (3.19) WIL = − ij ij VL

SL

where VL and SL are the volume and area of the dislocation loop, respectively. Plastic distortion ε∗L ij of a prismatic dislocation loop located in the xoy plane in the xyz coordinate system with the origin at the loop center is ε∗L zz = ±bH(1 − r/rL )δ(z), H(1 − r/rL ) is the Heaviside function and δ(z) is the Dirac delta function. σij1 are 1 the normal stress in the z-direction. the stresses in the QD, with σzz Substituting Eqs. (3.18) and (3.19) and expressions of σij1 for the cases satisfying or not satisfying the compatibility equation into Eq. (3.17), we can obtain the critical radius RcI for the spherical QD under nonuniform eigenstrains ε∗ satisfying the compatibility equation of strains, RcI =

Rc0 , (k0 + k1 )

(3.20)

and the critical radius RcII for the spherical QD under nonuniform eigenstrains ε∗ not satisfying the compatibility equation, RcII =

Rc0 , (k0 + 0.75k1 )

(3.21)

30

H. L. Duan et al.

2.00 RcI RcII

Rcr /Rc0

1.75 1.50 1.25 1.00 20.5

20.4

20.3

20.2

20.1

0.0

k1

Fig. 3.6 Variation of critical radii for dislocation nucleation in QDs with the composition parameter k1 (k0 = 1). Reprinted from Duan et al. (2006b) with acknowledgment to American Physical Society.

where Rc0 is the critical radius of a spherical QD under uniform hydrostatic eigenstrain ε∗m0 (Kolesnikova and Romanov, 2004) 1.083αRc0 3b Rc0 = ln . (3.22) 8π(1 + ν)ε∗m0 b It can be seen from Eqs. (3.20) and (3.21) that RcI /RcII = 1 − 0.25k1 / (k0 + k1 ). It is evident that k0 > 0, k0 + k1 > 0. Generally, for the “self-capping” alloyed QD (e.g., Inx Ga1−x As on GaAs substrate), the core is enriched in In, whereas the outermost layer becomes progressively depleted in In (Tersoff, 1998). Therefore, in the composition profile chosen here, k1 < 0. Fig. 3.6 shows the variation of the normalized critical radii Rcr /Rc0 with k1 (where Rcr stands for RcI and RcII ). The results show that dislocation nucleation is more difficult in a compositionally nonuniform QD than in a uniform one (cf., Rcr /Rc0 > 1) in both situations. However, it is even more difficult when the compatibility equation is satisfied than when it is not (RcI /Rc0 > RcII /Rc0 for k1 < 0). 4. Micromechanical Framework for Nano-inhomogeneities with Interface Stress The interface stress contributes to the effective moduli of composites in two ways. First, it affects the average stress (strain) in each inhomogeneity, and this effect can be taken into account by the use of the so-called stress (strain) concentration tensor in the inhomogeneity (cf. Section 2.2). Second, the discontinuities in the traction across the interface directly participate in the calculation of the volume average of the strain or stress, and this effect can be taken into account by use of the stress (strain) concentration tensor at the interface. The effective


31

moduli of solids with interface stress effect can be modelled with the well-known micromechanical schemes, provided these are suitably modified to account for the discontinuity in the tractions across the interfaces. For example, Benveniste (1985) has given the general framework with consideration of the displacement discontinuity, and Hashin (1991) has used this framework to predict the effective moduli of composites with linear spring interfaces (displacement discontinuity). In view of the importance of the surface/interface stress effect at the nanoscale, a framework has been proposed by Duan et al. (2005b) to include stress discontinuity in order to take into account the surface/interface stress effect. Many micromechanical schemes have been successfully used for obtaining effective elastic constants of heterogeneous solids. For a comprehensive exposition, one can refer to the monographs of Aboudi (1991), Nemat-Nasser and Hori (1999), Milton (2002), and Torquato (2002). For the prediction of the effective properties of nonlinear composites, one can refer to the works of Ponte Castañeda and Suquet (1998) and Willis (2000). For the sake of simplicity but without loss of the physical essence of the surface/interface stress effect, we shall use three schemes to predict the effective elastic constants of solids containing nanoinhomogeneities with the surface/interface stress effect described by Eqs. (2.2) and (2.6). The three schemes are Hashin’s composite sphere assemblage model (CSA; Hashin, 1962), the Mori–Tanaka method (MTM; Mori and Tanaka, 1973), and the generalized self-consistent method (GSCM; Christensen and Lo, 1979). Consider a representative volume element (RVE) consisting of a two-phase medium occupying a volume V with external boundary S, and let VI and Vm denote the volumes of the two phases I and m , respectively. The interface stress effect is taken into account at the interface with outward unit normal n between I and m . The heterogeneous material is assumed to be statistically homogeneous with the inhomogeneity moduli CI (compliance tensor DI ) and matrix moduli Cm (compliance tensor Dm ). fI and (1 − fI ) denote the volume fractions of the inhomogeneity and matrix, respectively. To define the effective elastic moduli of a composite, we use the usual concept of homogeneous boundary conditions imposed on a RVE. As in the work of Benveniste and Miloh (2001), we define the average strain ε¯ and average stress σ¯ as follows: 1 (N ⊗ u + u ⊗ N) dS, ε¯ = 2V S 1 (σ · N) ⊗ x dS, σ¯ = V S

(4.1) (4.2)

where N is the outward unit normal vector to S, and x is the position vector. In the presence of interface stress effect (stress discontinuity), the average strain and

32

H. L. Duan et al.

average stress are ε¯ = (1 − fI ) ε¯ m + fI ε¯ I , σ¯ = (1 − fI ) σ¯ m + fI σ¯ I +

fI VI

(4.3)

([σ] · n) ⊗ x d,

(4.4)

where ε¯ k and σ¯ k (k = I, m) denote volume averages of the strain and stress over the respective phases in the RVE. [σ] = σ I − σ m . As usual, the effective elastic moduli of the composite can then be determined by subjecting the external surface S to homogeneous displacement or traction boundary conditions, defined as u(S) = ε0 · x,

(4.5)

(S) = σ · N,

(4.6)

0

ε0

σ0

where and are constant strain and stress tensors, respectively. In the following, we will first derive formulas relating the average stress (strain) in the inhomogeneities and at the interface to the applied stress (strain) under both types of boundary condition (4.5) and (4.6). These formulas are needed to calculate the effective moduli of the composite according to the dilute concentration approximation and GSCM schemes. It is easy to derive formulas relating the average stress (strain) in the inhomogeneities and at the interface to the average stress (strain) in the matrix, again under both types of boundary condition (4.5) and (4.6). These formulas are needed in MTM. Under homogeneous displacement boundary conditions Eq. (4.5), define a strain concentration tensor R in the inhomogeneity and a strain concentration tensor T at the interface such that 1 I 0 ([σ] · n) ⊗ x d = Cm : T : ε0 ε¯ = R : ε , (4.7) VI ¯ of the composite From Eqs. (4.3)–(4.5) and (4.7), the effective stiffness tensor C is given by ¯ = Cm + fI (CI − Cm ) : R + fI Cm : T. C

(4.8)

Under homogeneous traction boundary conditions Eq. (4.6), define two stress concentration tensors U (in the inhomogeneity) and W (at the interface) by the relations 1 I 0 (4.9) ([σ] · n) ⊗ x d = W : σ 0 . σ¯ = U : σ , VI Then the effective compliance tensor S¯ of the composite is given by S¯ = Sm + fI (SI − Sm ) : U − fI Sm : W.

(4.10)


33

Eqs. (4.8) and (4.10) can be used to calculate the effective moduli of composites by using the dilute concentration approximation and GSCM once R, T, U, and W have been obtained. If the inhomogeneity and matrix are both isotropic, and the composite is macroscopically isotropic, then R and T in Eq. (4.7) can be expressed as R = R1 J 1 + R2 J 2 ,

T = T1 J1 + T2 J2

(4.11)

1 J2 = − I(2) ⊗ I(2) + I(4s) 3

(4.12)

in which J1 =

1 (2) I ⊗ I(2) , 3

with I(4s) the fourth-order symmetric identity tensor. R1 , R2 , T1 , and T2 are four scalars to be determined from the adopted micromechanical scheme. Then Eq. (4.8) decouples into κ¯ = κm + fI [(κI − κm )R1 + κm T1 ],

(4.13)

μ ¯ = μm + fI [(μI − μm )R2 + μm T2 ].

(4.14)

Let us now relate the average stress (strain) in the inhomogeneity and the average stress difference at the interface to the average stress (strain) in the matrix, following the Mori–Tanaka procedure (Benveniste, 1987). Under the homogeneous displacement boundary conditions Eq. (4.5), define two strain concentration tensors M (in the inhomogeneity) and H (at the interface) by the relations 1 ([σ] · n) ⊗ x d = Cm : H : ε¯ m , ε¯ I = M : ε¯ m , (4.15) VI

−1 0 where ε¯ m = I(4s) + f(M − I(4s) ) : ε . Then the effective stiffness tensor can be obtained from −1

¯ = Cm + fI CI − Cm : M + Cm : H : I(4s) + fI (M − I(4s) ) . (4.16) C Likewise, under the homogeneous traction boundary conditions Eq. (4.6), the effective compliance tensor can be obtained from −1

S¯ = Sm + fI SI − Sm : P − Sm : Q : I(4s) + fI (P + Q − I(4s) ) , (4.17) where P and Q are stress concentration tensors in the inhomogeneity and at the interface, respectively. They are defined by 1 ([σ] · n) ⊗ x d = Q : σ¯ m , σ¯ I = P : σ¯ m , (4.18) VI

34

H. L. Duan et al.

−1 0 where σ¯ m = I(4s) + fI (P + Q − I(4s) ) : σ . Eqs. (4.16) and (4.17) can be used to calculate the effective moduli of composites using MTM. If the inhomogeneity, matrix, and composite are isotropic, then the two strain concentration tensors M and H in Eq. (4.15) can be expressed as M = M1 J1 + M2 J2 ,

H = H1 J1 + H2 J2 ,

(4.19)

where M1 , M2 , H1 , and H2 are four scalars to be determined using MTM. With the use of Eq. (4.19), Eq. (4.16) decouples into κ¯ = κm + fI [(κI − κm )M1 + κm H1 ] [1 + fI (M1 − 1)]−1 , μ ¯ = μm + fI [(μI − μm )M2 + μm H2 ] [1 + fI (M2 − 1)]

−1

.

(4.20) (4.21)

5. Application of Micromechanical Framework for Nano-inhomogeneities

5.1. Elastic Moduli of Solids with Spherical Nano-inhomogeneities For predicting the effective moduli of a composite containing spherical nanoinhomogeneities, it is convenient to split the boundary displacement u0 (S) into its 0 and deviatoric parts u0 , that is, dilatational um e 0 + u0 = ε0 I(2) · x + 2ε0 [e ⊗ e − 1 (e ⊗ e + e ⊗ e )] · x u0 (S) = um z x x y y m e A z 2 (5.1) in which ε0m = (trε0 )/3, ε0 is the imposed strain tensor, ε0A is a constant, and ex , ey , and ez are the unit base vectors of the Cartesian coordinate system. The boundary 0 and u0 will be used to predict the effective bulk and conditions corresponding to um e shear moduli, respectively. In the following, we will predict the effective elastic moduli of a composite with spherical nano-inhomogeneities by three schemes (CSA, MTM, and GSCM). The interface stress effect in each scheme is additionally considered at the interface between the inhomogeneity and matrix.

5.1.1. Prediction of Elastic Moduli by CSA The configuration of the CSA consists of two concentric spheres with radii r = R and r = R0 (fp = (R/R0 )3 ) that correspond to the radius of inhomogeneity and the outer radius of matrix, respectively. The boundary conditions are imposed at the outer boundary of the matrix (r = R0 ). The solutions for finding the effective moduli of the composite with spherical nano-inhomogeneities are given in the spherical coordinate system (r, θ, ϕ). The interface conditions at the interface of the


35

inhomogeneity and matrix (r = R) consist of displacement continuity conditions and Eq. (2.2), and for axisymmetric loading, they can be obtained from Eq. (2.3), that is, ⎧ p p ⎪ ur = um uθ = um r , ⎪ θ , ⎪ ⎪ ⎪ ⎨ (τθθ + τϕϕ ) m p σrr − σrr = , (5.2) R ⎪ ⎪ ⎪ ⎪ p τθθ − τϕϕ 1 ∂τθθ ⎪ m ⎩ σrθ − σrθ + cot θ. = R ∂θ R The interface stresses ταβ (α, β = θ, ϕ) can be obtained from Eq. (2.6), that is, ταβ = 2μs εsαβ + λs (trεs )δαβ ,

(5.3)

where the interface strain εs is equal to the tangential strain in the abutting bulk materials (inhomogeneity and matrix). The solution for CSA should satisfy the interface conditions Eq. (5.2) and the boundary conditions at the outer surface of the matrix r = R0 . For predicting the effective bulk modulus of the composite with spherical nano-inhomogeneities, assume that the configurations for CSA undergo a hydrostatic deformation with the imposed strain being ε0m = 0. Then the boundary displacements in the spherical coordinate system are u0r = ε0m r,

u0θ = 0,

u0ϕ = 0.

(5.4)

For CSA, the nonvanishing displacement component for finding the bulk modulus of the composite is Gk (5.5) ukr = Fk r + 2 , r where Fk and Gk (k = p, m for CSA) are constants to be determined. It is noted that for CSA, the constants Fk and Gk (k = p, m) need to be determined from the boundary conditions Eq. (5.4) at r = R0 , the interface conditions Eq. (5.2), and the condition to avoid a singularity at r = 0. The bulk modulus is then obtained from Eq. (4.13). It is found that the effective bulk modulus depends on the size of the inhomogeneities κ¯ =

3κm (3κp + 4fp μp ) + 2μp [4fp μp κsr + 3κp (2 − 2fp + κsr )] , 3[3(1 − fp )κm + 3fp κp + 2μp (2 + κsr − fp κsr )]

(5.6)

where κsr is given by Eq. (2.27). When κsr → 0, the result reduces to the classical one (without the interface stress effect). As only bounds can be obtained for the shear modulus of CSA, we do not predict the effective shear modulus of the composites by it.

36

H. L. Duan et al.

5.1.2. Prediction of Elastic Moduli by MTM For a composite with spherical nano-inhomogeneities, the configuration of MTM is a spherical nano-inhomogeneity with radius r = R embedded in an infinite matrix subjected to an imposed remote field equal to the as-yet-unknown average stress (strain) field in the matrix of the composite. Similar to those for predicting the effective bulk modulus by CSA, the boundary displacements and the displacement component for finding the bulk modulus of the composite are still given by Eqs. (5.4) and (5.5). It is noted that for MTM, Fk and Gk (k = p, m) need to be determined from the remote boundary conditions Eq. (5.4), the interface conditions Eq. (5.2), and the condition to avoid a singularity at r = 0. The effective bulk modulus is then obtained from Eq. (4.20), and the expression of effective bulk modulus is identical to Eq. (5.6). In order to predict the effective shear modulus of the composites, the imposed deviatoric strain (see Eq. (5.1)) is chosen as ε0xx = ε0yy = −ε0A , ε0zz = 2ε0A . The corresponding remote displacements in the spherical coordinate system are u0r = 2ε0A rP2 (cos θ),

u0θ = ε0A r

dP2 (cos θ) , dθ

u0ϕ = 0

at

r → +∞. (5.7)

For the present axisymmetric deformation, the corresponding solutions have the same form as Eqs. (2.12)–(2.14) for the MTM configuration. However, the k , C k , and Dk are replaced by A , B , C , and D (k = p, m), constants Akzz , Bzz k k k k zz zz respectively. From the remote displacement conditions Eq. (5.7), it follows that Am = 0 and Bm = ε0A ; to avoid a singularity at r = 0, it is necessary that Cp = Dp = 0. The remaining four constants are determined by the four interface conditions Eq. (5.2). Finally, the effective shear modulus using the MTM can be obtained from Eq. (4.21) and is μ ¯ =

μm [5 − 8fp ξ3 (7 − 5νm )] , 5 − fp (5 − 84ξ1 − 20ξ2 )

(5.8)

where 15(1 − νm )(κsr + 2μrs ) , 4H −15(1 − νm ) ξ2 = [η(7 + 5νp ) − 8νp (5 + 3κsr + μrs ) + 4H + 7(4 + 3κsr + 2μrs )], ξ1 =

ξ3 =

5 {2η2 (7 + 5νp ) − 4(7 − 10νp )(2 + κsr )(1 − μrs ) + 16H + η[7(6 + 5κsr + 4μrs ) − νp (90 + 47κsr + 4μrs )]},

(5.9)

(5.10)

(5.11)


37

H = −2η2 (7 + 5νp )(4 − 5νm ) + 7η[−39 − 20κsr − 16μrs + 5νm (9 + 5κsr + + 4μrs )] + ηνp [285 + 188κsr + 16μrs − 5νm (75 + 47κsr + 4μrs )] + + 4(7 − 10νp ){−7 − 11μrs − κsr (5 + 4μrs ) + + νm [5 + 13μrs + κsr (4 + 5μrs )]},

(5.12)

with μrs is given by Eq. (2.27), η = μI /μm . The effective shear modulus of the composite depends on the size of the inhomogeneity through two nondimensional parameters κsr and μrs . When κs and μs are equal to zero or κsr → 0, μrs → 0, the shear modulus reduces to the classical result. 5.1.3. Prediction of Elastic Moduli by GSCM The configuration of the GSCM is a three-phase model, that is, a spherical nanoinhomogeneity (r = R) with a matrix shell (outer radius r = R0 ) embedded in an infinite effective medium (i.e., the composite material) and boundary conditions are specified at infinity. In the GSCM scheme, the interface stress effect is additionally considered at the interface between the inhomogeneity and matrix (cf. Eq. (5.2)), and conventional stress and displacement continuity conditions are assumed to prevail at the interface between the matrix shell and effective medium (r = R0 ), that is, e um r = ur ,

e um θ = uθ ,

m = σe , σrr rr

m = σe , σrθ rθ

(5.13)

where the superscript “e” denotes the effective medium. The boundary displacements and the nonvanishing displacement component for finding the bulk modulus of the composite are still given by Eqs. (5.4) and (5.5). For GSCM, the constants Fk and Gk (k = p, m, e) need to be determined from the remote boundary conditions Eq. (5.4), the interface conditions Eqs. (5.2) and (5.13), and the condition to avoid a singularity at r = 0. The bulk modulus is then obtained from Eq. (4.13). It is found that, like the classical case without the interface stress effect, the CSA , MTM, and GSCM give the same prediction of the effective bulk modulus for a given composite, but unlike the classical results, the effective modulus depends on the size of the inhomogeneities In order to predict the effective shear modulus by GSCM, we still apply the boundary condition Eq. (5.7). The corresponding solutions have the same k , C k , and Dk replaced by form as Eqs. (2.12)–(2.14) with the constants Akzz , Bzz zz zz Ak , Bk , Ck , and Dk , respectively. In the GSCM model, the constants Ak , Bk , Ck , and Dk (k = p, m, e) are determined by the interface conditions, Eqs. (5.2) and (5.13), and the remote boundary conditions. To avoid a singularity at r = 0, we must have Cp = Dp = 0; to satisfy the remote displacement conditions Eq. (5.7),

38

H. L. Duan et al.

we must have Ae = 0 and Be = ε0A . The remaining eight constants are determined from the eight interface conditions Eqs. (5.2) and (5.13). Moreover, it can be shown by the energy method proposed by Christensen and Lo (1979) that Ce = 0. This method is based on the argument that the strain energy stored in the embedded composite sphere is given by the product of the average strain energy density of the composite and the volume of the composite sphere. Here, we will prove that Ce = 0 by energy method for nano-inhomogeneity with interface stress effect. For a homogeneous medium containing an nanoinhomogeneity with interface stress effect, the strain energy U, under imposed displacement boundary conditions Eq. (4.5), is given by Eq. (2.47). In Eq. (2.47), U represents the total strain energy stored in the configuration of GSCM (with interface stress effect). Following the procedure of Christensen and Lo (1979), a sphere of radius r = R0 is removed from the effective homogeneous medium and replaced by a composite sphere with interface stress effect (with the outer radius r = R0 and inner radius r = R) such that (R/R0 )3 = fp . The strain energy of the medium as a whole should remain unaffected by this replacement. In terms of the Eshelby formula Eq. (2.47), this implies that if U0 denotes the strain energy of the effective homogeneous medium, and U stands for the strain energy of the same medium but now containing the composite sphere with interface stress effect at r = R, then U = U0 . The integral along in Eq. (2.47), which is to be evaluated at r = R0 , should then vanish. Substituting the expressions of the displacement and stress of GSCM configuration into the integral in Eq. (2.47) leads to Ce = 0. The effective shear modulus using GSCM can be obtained by Eq. (4.14), in which R1 and T1 are given by p

R1 =

e¯ zz , 2ε0A

T1 =

¯ zz 1 ϒ , 2μm 2ε0A

(5.14)

p

where e¯ zz is the component of volume average deviatoric strain tensor (¯ep ) in ¯ zz is the volume average tensor of stress difference at the the inhomogeneity, ϒ ¯ is defined by interface in the z-direction, and ϒ ¯ = ϒ

1 VI

([s] · n) ⊗ x d,

(5.15)

where [s] = sm − sp with sk = 2μk ek (k = p, m) being the deviatoric stress tensor. Then according to Eqs. (5.2), (5.13), (4.14), and (5.14), the effective shear modulus obtained by GSCM is a quadratic equation in η∗ = μ/μ ¯ m, A η∗2 + B η∗ + C = 0,

(5.16)


39

where A , B , and C are functions of the volume fractions and elastic moduli of the inhomogeneity, matrix, and interface. The solution of this quadratic equation gives the normalized effective shear modulus μ/μ ¯ m. Like the Eshelby and the stress concentration tensors in the preceding section, the effective moduli are functions of the two intrinsic length scales lκ and lμ defined in Eq. (2.27). Duan et al. (2005b) calculated the effective moduli of aluminium containing spherical nanovoids using the free-surface properties obtained by molecular dynamic simulations (Miller and Shenoy, 2000). Two sets of surface moduli (Cases A and B mentioned in Section 3.1) are used. The normalized bulk modulus κ¯ /¯κc for different surface properties as a function of the void radius R is plotted in Fig. 5.1, and the variation of μ/ ¯ μ ¯ c (calculated by GSCM) is plotted in Fig. 5.2, where “A” and “B” denote the two sets of surface properties and “C” the

A, [1 0 0] B, [1 1 1] C

1.2

␬/␬c

1.1 1.0 0.9 10

20

30 R(nm)

40

50

Fig. 5.1 Effective bulk modulus as a function of void radius (f = 0.3). A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1]; C: the classical results without the surface stress effect. Reprinted from Duan et al. (2005b) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK. 1.05 0.90 ␮/␮c

A, [1 0 0] B, [1 1 1] C

0.75 0.60 10

20

30 R(nm)

40

50

Fig. 5.2 Effective shear modulus as a function of void radius (f = 0.3). A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1]; C: the classical results without the surface stress effect. Reprinted from Duan et al. (2005b) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK.

40

H. L. Duan et al.

¯ c represent the classical results without the surface stress classical result. κ¯ c and μ effect. It is found that the surface stress effect has a significant effect on the effective bulk and shear moduli, especially when nanovoids are less than 10 nm in radius. The surface stress effect becomes negligible when the radius is larger than 50 nm.

5.2. Generalized Levin’s Formula and Hill’s Connections Levin (1967) derived a simple formula relating the effective CTE to the effective elastic moduli of a two-phase heterogeneous material. Earlier, Hill (1964) had shown that for any two-phase transversely isotropic heterogeneous material containing parallel cylindrical fibers, the five effective elastic constants are interrelated, with only three of them being independent. Both Levin’s formula and Hill’s connections are for a perfect interface in the sense that the field quantities are continuous across it. The question arises, do Levin’s formula and Hill’s connections have counterparts in the presence of surface/interface stress? Here, this question will be answered in the affirmative. We will give the generalized Levin’s formula and Hill’s connections for the heterogeneous materials containing spherical particles or cylindrical fibers, which take into account the surface/interface stress effect between the inhomogeneity and the matrix. In the following, if we assume that there exists a homogeneous deformation field in a RVE of the heterogeneous material, we will prove that, under specific types of external loading and a uniform temperature change, this uniform deformation field can satisfy all basic equations and can be viewed as a characteristic field in various admissible deformation modes (Dvorak, 1990). We shall use it to obtain the generalized Levin’ formula and the generalized Hill’s connections for the heterogeneous media with interface stress effect. 5.2.1. Generalized Levin’s Formula for Spherical Particles Assume that the matrix and the spherical particles are isotropic and the latter are randomly distributed in the former. The effective elastic moduli and the effective CTE of such an heterogeneous medium are also isotropic. Consider a RVE consisting of a volume V of the two-phase medium, and let Vp and Vm denote the volumes of the spherical particles and matrix, respectively. The interface stress effect is taken into account at the interface between a particle and the matrix. Assume that the RVE is subjected to a hydrostatic deformation together with a uniform temperature change T . We will now prove that, under these deformation and temperature conditions, it is possible to generate the following uniform displacement field in the RVE (in the spherical coordinate system (r, θ, ϕ)): ukr (r, θ, ϕ) = e0 r,

(5.17)


41

where e0 is a constant. Under this hydrostatic deformation mode, the boundary conditions (Eqs. (2.2) and (2.6)) at the interfaces between the particle and matrix would require that the following equation be satisfied 2κs 2αs κs e0 3κm − 3κp − − T 3αm κm − 3αp κp − = 0. (5.18) R R Thus, if the external deformation e0 and the temperature change T are chosen according to Eq. (5.18), then the uniform deformation field Eq. (5.17) can indeed prevail inside the RVE. In this case, the spherical particles in the matrix can be regarded as neutral ones in the sense that they do not disturb the elastic field Eq. (5.17). The volume average stress σ¯ and strain ε¯ in the RVE with interface stress effects are given by Eqs. (4.3) and (4.4). Under the uniform deformation field in Eq. (5.17), it follows from Eqs. (2.2), (2.6), (4.3), and (4.4) that

3fk κk (e0 − αk T ) + fp

k=p,m

2κs (e0 − αs T ) = 3¯κ(e0 − αT ¯ ). R

(5.19)

The solution of Eqs. (5.18) and (5.19) gives an exact relationship between the effective bulk modulus κ¯ and the effective CTE α¯ 2fp αs κs 2αs κs fk αk κk − α¯ ¯κ − 3R k=p,m 3R = . 2fp κs 2κs κp − κ m + κ¯ − fk κ k − 3R 3R k=p,m

αp κp − αm κm +

(5.20)

Eq. (5.20) is the sought-after generalized Levin’s formula for a two-phase heterogeneous medium containing spherical particles with interface stress effect. Note that Chen et al. (2007a) also obtained a relation (Eq. (31) in their paper) between κ¯ and α¯ for a heterogeneous medium containing spherical particles with interface stress effect. However, they did not include the thermoelastic term (T D0 ) in the interface constitutive equation Eq. (2.6). If we let αs = 0, Eq. (5.20) reduces to Eq. (31) of Chen et al. (2007a), and it reduces to Levin’s formula (Levin, 1967) when κs = 0 and αs = 0. 5.2.2. Generalized Levin’s Formula and Hill’s Connections for Cylindrical Fibers For a RVE of a heterogeneous medium containing aligned cylindrical fibers of the same radii with interface stress effect, we choose a cylindrical coordinate system (ρ, φ, z) in which the ρ − φ-plane is perpendicular and the z-axis is parallel to the fibers. We assume that the fibers are transversely isotropic so that the

42

H. L. Duan et al.

thermoelastic constitutive equations of the cylindrical fibers and matrix in Eq. (2.1) can be expressed in the following form: ⎛ k ⎞ ⎛ ⎞ ⎛ εk − α T ⎞ σρ kT ρ kk + μk kk − μk lk ⎜ k ⎟ ⎜ k ⎟ ⎝ ⎠ kk − μk kk + μk lk ⎝ εφ − αkT T ⎠ , ⎝ σφ ⎠ = (5.21) lk lk nk σk εk − α T z

k = 2p εk , σρz k ρz

z

k = 2p εk , σφz k φz

kL

k = 2μ εk , σρφ k ρφ

where kk , lk , nk , μk , and pk (k = f, m) are the elastic moduli of the fiber and the matrix in Hill’s notation (Hill, 1964), and αfT and αfL are the CTEs of the fibers in the transverse and longitudinal directions, respectively. For an isotropic matrix, αmT = αmL = αm , and km , lm , and nm can be expressed in terms of the bulk and shear moduli κm and μm , namely km = κm + μm /3, nm = κm + 4μm /3, pm = μm , lm = κm − 2μm /3. The heterogeneous medium with aligned cylindrical fibers exhibits transverse isotropy and has five effective elastic constants, that ¯ the longitudinal Young modulus is, the transverse plane-strain bulk modulus k, ¯ ¯ L , and the EL , the longitudinal Poisson ratio ν¯ L , the longitudinal shear modulus μ transverse shear modulus μ ¯ T . The effective CTEs are also transversely isotropic with the transverse and longitudinal components α¯ T and α¯ L . We now prove that there exists a certain axisymmetric loading that includes a uniform temperature change T which creates a uniform deformation field in the RVE, described by the strain field ερρ = e0 ,

εφφ = e0 ,

εzz = ε0 .

(5.22)

For this axisymmetric deformation mode to exist, the interface conditions (Eqs. (2.2) and (2.6)) between the fiber and matrix must satisfy the following equation: λs λs + 2μs ε0 lm − lf − + e0 2km − 2kf − ρ0 ρ0 (5.23) αsT κs − lm αmL + 2km αmT − lf αfL − 2kf αfT − T = 0, ρ0 where ρ0 is the radius of the fibers, and αsT is the interface CTE in the transverse direction. Eq. (5.23) can be satisfied by an appropriate choice of the external loading parameters e0 , ε0 , and T . In this case, the cylindrical fibers in the matrix can be regarded as neutral ones in the sense that they do not disturb the elastic fields Eq. (5.22). We now derive the volume average stress and strain in the RVE with aligned cylindrical fibers under the local strain field Eq. (5.22). From Eqs. (4.3) and (4.4),


43

the volume average strain and stress (¯εij and σ¯ ij , i, j = x, y) in the transverse plane of RVE can be written as f

ε¯ ij = ff ε¯ ij + fm ε¯ m ij , f

σ¯ ij = ff σ¯ ij + fm σ¯ ijm +

ff Sf

(5.24)

f

m (σik − σik )nk xj d,

where Sf is the cross-sectional area of a cylindrical fiber. The volume average strain and stress in the axial direction are τzz f m + fm σ¯ zz + 2ff , (5.25) ε¯ zz = ε0 , σ¯ zz = ff σ¯ zz ρ0 where τzz is the interface stress in the z-direction given by Eq. (2.6). From Eqs. (2.2), (5.22), (5.24), and (5.25), we can obtain the following two expressions:

fk [2kk (e0 − αkT T ) + lk (ε0 − αkL T )]

k=f,m

+

ff [(λs + 2μs )e0 + λs ε0 − αsT κs T ] ρ0

¯ 0 − αeT T ) + le (ε0 − αeL T ), = 2k(e

(5.26)

fk [2lk (e0 − αkT T ) + nk (ε0 − αkL T)2e0 λm ]

k=f,m

+

2ff [e0 λs + ε0 (λs + 2μs ) − αsL κs T ] ρ0

= 2le (e0 − αeT T ) + ne (ε0 − αeL T ),

(5.27)

where αsL is the CTE of the interface in the longitudinal direction. Solving Eqs. (5.23), (5.26), and (5.27), we obtain two exact expressions. ¯ ¯l, and n) The first expression relates the three effective elastic moduli (k, ¯ ff (λs + 2μs ) λs + 2μs k¯ − fk k k − 2ρ0 k=f,m 2ρ0 = λs f f λs ¯l − lm − l f − fk lk − ρ0 ρ0 k=f,m

k m − kf − l

¯l −

fk l k − k=f,m

= n¯ −

fk n k − k=f,m

ff λs ρ0

2ff (λs + 2μs ) ρ0

,

(5.28)

44

H. L. Duan et al.

¯ L + 4k¯ ν¯ 2 , ρ0 is the radius of the fibers, and αsT and αsL where ¯l = 2k¯ ν¯ L , n¯ = E L are the interface CTEs in the transverse direction and in the longitudinal direction, respectively. The two equalities prove that only three of the five effective elastic moduli are independent. Eq. (5.28) is identical to Eq. (13) in the paper of Chen and Dvorak (2006). The two equalities Eq. (5.28) reduce to Hill’s connections (Hill, 1964) when λs = 0 and μs = 0. The second expression relates the effective CTE to the effective elastic moduli 2km αmT + lm αmL − (2kf αfT + lf αfL ) − km − k f − 2k¯ α¯ T + ¯lα¯ L − =

fk (2kk αkT + lk αkL ) − k=f,m

k¯ −

fk k k − k=f,m

2¯lα¯ T + n¯ α¯ L − =

λs + 2μs 2a

αsT κs ρ0

ff (λs + 2μs ) 2ρ0

fk (2lk αkT + nk αkL ) − k=f,m

¯l −

ff αsT κs ρ0

λs fk lk − ff ρ 0 k=f,m

2ff αsL κs ρ0

.

(5.29)

Eq. (5.29) can be regarded as the generalized Levin’s formula for the heterogeneous material containing aligned cylindrical fibers with interface stress discontinuity. The effective CTEs α¯ T and α¯ L can be obtained by solving the two equalities in ¯ ν¯ L , and E ¯ L are given in the paper of Chen et al. Eq. (5.29). The expressions of k, ¯ ν¯ L , (2007b). For the heterogeneous material with aligned cylindrical nanopores, k, ¯ L are given by Duan et al (2006c). Chen and Dvorak (2006) obtained relations and E (Eq. (14) in their paper) between the effective elastic moduli and effective CTEs for a heterogeneous material containing aligned cylindrical fibers with interface stress effect but without taking into account the thermoelastic term (T D0 ) in the interface constitutive equation Eq. (2.6). Eq. (5.29) reduces to their result when αsT = αsL = 0. It reduces to Levin’s formula (Levin, 1967) when κs = 0, αsT = 0, and αsL = 0. It is emphasized that Pathak and Shenoy (2005) have shown that the CTE of the surface of nanostructured materials is different from that of the parent bulk materials. By using the present continuum theory and molecular dynamics simulations, they showed that the CTE of the surface of a nanoslab has a significant effect on its effective CTE, and excellent agreement is found between the continuum theory and molecular dynamics simulations. Therefore, the generalized Levin’s formula with interface stress effect will provide a guideline for tailoring the effective CTE


45

of heterogeneous materials, especially, that of nanostructured materials (e.g., the nanochannel-array materials). 5.2.3. Effective CTE of Composites with Spherical, or Parallel Cylindrical, Nanopores For solids containing spherical nanopores or aligned cylindrical nanopores, the effective CTEs of solids can be obtained from the generalized Levin’s formulas (Eq. (5.20) or (5.29)) by letting the elastic mouli of the spherical particles or cylindrical fibers equal to zero. κ¯ in Eq. (5.20) is given by Eq. (5.6) with κp = ¯ ¯l, and n¯ in Eq. (5.29) for the solids containing aligned cylindrical μp = 0. k, nanopores will be given in the next application example. We will now analyze the effect of the surface elastic and thermoelastic terms on the effective CTEs of solids containing spherical nanopores or aligned cylindrical nanopores. The numerical results are presented for aluminium, and the free-surface elastic moduli are taken from the papers of Miller and Shenoy (2000) and Sharma et al. (2003). These freesurface elastic moduli of Al have been obtained by molecular dynamic simulations (Miller and Shenoy, 2000). Two sets of surface moduli (Cases A and B mentioned in Section 3.1) are used. The CTE of aluminum is αm = 5.01 × 10−5 K −1 (Pathak and Shenoy, 2005), and the volume fraction of spherical or cylindrical nanopores is fp = ff = 0.3. We assume that the surface CTE is αs = 5αm . The normalized effective CTE α/ ¯ α¯ c for spherical nanopores and α¯ T /α¯ cT for aligned cylindrical nanopores for different surface properties as a function of the pore radius are plotted in Figs. 5.3 and 5.4, where “A” and “B” denote the two designated sets of surface properties and “C” the classical result (no surface stress effect). α¯ c and α¯ cT denote the effective CTEs of porous Al with spherical and cylindrical nanopores without the surface stress effect. It is seen from Figs. 5.3 and 5.4 that α/ ¯ α¯ c and α¯ T /α¯ cT decrease (or increase) with an increase in the void size due to the surface stress effect, whereas there is no size effect when the surface stress is absent. The surface stress effect on the effective CTEs becomes negligible for pores larger than 30 nm in radius. It is noted that by using the continuum theory and molecular dynamics simulations, Pathak and Shenoy (2005) showed that the CTE of the surface of a nanoslab has a significant effect on its CTE, and similar curves as Figs. 5.3 and 5.4 for CTEs of Si and Al nanoslabs have been obtained. 5.2.4. Equivalence Between ISM and Interphase Models It can be seen from Eqs. (5.20) and (5.29) that the effective CTE α¯ e for spherical particles and the effective CTEs α¯ T and α¯ L for cylindrical fibers are dependent on the interface elastic moduli and CTEs, which must be experimentally determined. However, as the ISM can be used to simulate the behavior of thin interphases (Wang et al., 2005), these interface parameters can be deduced from the

46

H. L. Duan et al. 1.4 A, [1 0 0] B, [1 1 1] C

␣e / ␣c

1.2

1.0

0.8 1

5

10

15 R(nm)

20

25

30

Fig. 5.3 Effective normalized α/ ¯ α¯ c as a function of the radius of spherical nanopores (fp = 0.3). A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1]; C: the classical results without the surface stress effect. Reprinted from Duan and Karihaloo (2007) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK. 1.50 A, [1 0 0] B, [1 0 0] C

␣–eT / ␣–cT

1.25

1.00

0.75 1

5

10

15 20 ␳0(nm)

25

30

Fig. 5.4 Effective normalized α¯ T /α¯ cT as a function of the radius of cylindrical nanopores (fp = 0.3). A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1]; C: the classical results without the surface stress effect. Reprinted from Duan and Karihaloo (2007)) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK.

equivalence relationships that exist between the thin interphase and the ISM. Such relationships, however, only exist for elastic moduli (Benveniste and Miloh, 2001; Hashin, 2002; Wang et al., 2005; Benveniste, 2006). The procedures of Hashin (2002) and Wang et al. (2005) can, however, be followed to derive similar relationships for the thermoelastic problem, using appropriate thermoelastic constitutive relations for the inhomogeneity, matrix, and interface (Eqs. (2.1) and (2.6)). We, therefore, derive these relationships giving only the most essential details. For a thin interphase between the inhomogeneity and the matrix, denote the interface between the inhomogeneity and the interphase by 1 , and that between


47

the interphase and the matrix by 2 . For brevity, we illustrate the procedure on a spherical particle; the procedure is the same for a cylindrical fiber. The differences in the displacement and stress (uj and σrj , j = r, θ, ϕ) across the interphase can be approximated with sufficient accuracy (Hashin, 2002) by the relations ' uj = ucj (R + t) − ucj (R) = t ucj, r '1 , (5.30) ' c ' σrj = σrjc (R + t) − σrjc (R) = t σrj, r 1 , where t is the interphase thickness, the subscript 1 means that the corresponding quantities are evaluated at interface 1 , and the superscript “c” denotes the interphase. To obtain the interface conditions equivalent to the thin interphase, the differences in the displacement and stress (uj and σrj ) across the interphase should be equal to the displacement and stress jumps ([uj ] and [σrj ]) across the interface (), [uj ] = uj ,

[σrj ] = σrj .

(5.31)

Here, [uj ] and [σrj ] are defined by p

[uj ] ≡ um j () − uj (),

p

[σrj ] ≡ σrjm () − σrj (),

(5.32)

where is the interface between the inhomogeneity and matrix. For a thin and stiff interphase, the characteristics of the displacements and stresses across the interphase can be described by uj = 0, σrj = finite (Wang et al., 2005), which have the same features as those of the ISM (Eq. (2)), p p m namely um j () = uj (), [σrj ] = σrj () − σrj () = σrj . Therefore, the equivalence between a thin and stiff isotropic interphase and an ISM is assured if the elastic moduli and CTE (both for the spherical particle and cylindrical fiber) of the latter meet the following conditions: λs =

2μc νc t , 1 − νc

μs = μc t,

αs = αc ,

(5.33)

where κs = 2(λs + μs ). νc , μc , and αc are the Poisson ratio, shear modulus, and CTE of the interphase, respectively.

5.3. Prediction and Tailoring of Elastic Moduli of Nanochannel-array Materials The fabrication, structure, and properties of nanostructured materials with feature sizes in the tens to several hundreds of nanometer range have attracted considerable recent interest. These materials include nanochannel-array materials,

48

H. L. Duan et al.

nanocrystalline metals, thin films, nanowires, nanobeams, nanobelts, etc. Particularly, the relationship between their structures and functional properties has been the major focus of the studies. As the number of atoms near the surface/interface in these materials is large compared to the total number of atoms, the surface/interface stress effect on their properties can be significant. Gleiter (2000) and Weissmüller et al. (2003) have pointed out that nanostructured materials with a large ratio of the interface/surface to volume open the way to modifying the electronic structure and related properties of solids. Among the above-mentioned nanostructured materials, nanochannel-array materials have been extensively used in nanotechnology. They can be used as filters and in catalytic convertors, as well as templates for nanosized magnetic, electronic, and optoelectronic devices (Masuda and Fukuda, 1995; Martin and Siwy, 2004; Shi et al., 2004). As these materials possess a large surface area, pore surfaces can be modified to create nanoporous materials that are very stiff and light and have very low thermal conductivity. One important immediate application of these materials is as cores in sandwich construction. 5.3.1. Prediction of Elastic Moduli of Nanochannel-array Materials For the nanochannel-array materials with aligned cylindrical nanopores (Fig. 5.5), we choose a Cartesian coordinate system (x, y, z) such that the z-axis is parallel to aligned cylindrical nanopores and the x − y-plane is perpendicular to them. In a cylindrical coordinate system (ρ, φ, z), the ρ − φ-plane is perpendicular to the pores. For generality, we assume that the matrix is linearly elastic

Fig. 5.5 A nanochannel-array material with aligned cylindrical nanopores. Reprinted from Duan et al. (2006c) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK.


49

and transversely isotropic in the plane perpendicular to the pores, and the surface of the aligned cylindrical nanopores is orthotropic. Then, the surface constitutive equation can be written as follows: s s s s s τzz = C1111 εszz + C1122 εsφφ , τφφ = C2211 εszz + C2222 εsφφ , τφz = 2C1212 εsφz , (5.34) s s s s s , C2222 , C1122 , C2211 , and C1212 are the surface elastic constants. Since where C1111 nanochannel-array materials have aligned and approximately hexagonal closepacked array of cylindrical pores (Masuda and Fukuda, 1995; Miyata et al., 2004), they will exhibit an overall transversely isotropic response. Therefore, we shall ¯ E ¯ L , ν¯ L , μ predict the five effective elastic constants, namely k, ¯ L , and μ ¯ T . The subscript “L” denotes a longitudinal property along the axis of the pores and “T” a transverse property perpendicular to them; here and in the following, the superand subscripts “m,” “e,” and “s” denote the quantities pertaining to the matrix, the effective medium, and the surface, respectively. We shall use two micromechanical models, namely the composite cylinder assemblage model (CCA) (Hashin and Rosen, 1964) and the generalized selfconsistent method (GSCM) (Christensen and Lo, 1979), to predict the effective (overall) elastic constants of the nanochannel-array materials with aligned cylindrical nanopores. As mentioned above, these methods are simple and have been found to give accurate predictions of effective elastic constants of heterogeneous materials. The corresponding micromechanical framework with interface stress effect has been given in Section 4. The configuration of the composite cylinder model for predicting the effective elastic constants consists of two concentric cylinders with radii ρ = ρ0 and ρ = ρ1 , which correspond to the radius of a cylindrical pore and the outer radius of matrix, respectively. The boundary conditions are imposed at the outer boundary of the matrix (ρ = ρ1 ). The configuration of the GSCM is a three-phase model, that is, a cylindrical pore (ρ = ρ0 ) with a matrix shell (outer radius ρ = ρ1 ) embedded in an infinite effective medium, and the boundary conditions are specified at infinity. Unlike the conventional composites containing aligned cylindrical fibers or pores, here the surface stress effect needs to be additionally considered on the surface of the cylindrical pore (ρ = ρ0 ) in each model. The boundary conditions on the surface of the cylindrical pore (ρ = ρ0 ) are given by Eq. (2.3), and in the cylindrical coordinate system, they can be expressed as

m = σρρ

τφφ , ρ0

m σρφ =−

∂τzφ 1 ∂τφφ − , ρ0 ∂φ ∂z

m =− σρz

∂τzz 1 ∂τφz − . ∂z ρ0 ∂φ

(5.35)

50

H. L. Duan et al.

The surface stress ταβ (α, β = φ, z) can be obtained from Eq. (5.34). For the GSCM, the interface between the matrix and the effective medium (ρ = ρ1 ) is perfectly bonded, that is, the conventional continuity conditions prevail e um ρ = uρ ,

e um φ = uφ ,

e um z = uz ,

m e σρρ = σρρ ,

m e σρφ = σρφ ,

m e σρz = σρz .

(5.36) The solution for CCA should satisfy the boundary conditions in Eq. (5.35) and the boundary condition at the outer surface of the matrix (ρ = ρ1 ). The solution for GSCM should satisfy the boundary and the interface conditions in Eqs. (5.35) and (5.36), and the remote boundary condition. In the following, the elastic constants ¯ E ¯ L , ν¯ L , μ ¯ L will be predicted by CCA and GSCM, and μ ¯ T by GSCM. k, ¯ To predict k, ¯ we apply nonvanishing strain (a) Transverse Bulk Modulus k. 0 0 0 0 0 components εxx and εyy (εxx = εyy = εm ) to the CCA and GSCM models. Then in the cylindrical coordinate system, the boundary conditions for CCA and the remote boundary conditions for GSCM can be expressed as follows: u0ρ = ε0m ρ,

u0φ = 0,

u0z = 0.

(5.37)

The displacement solutions to determine k¯ are ukρ = ak ρ +

bk , ρ

ukz = 0,

ukφ = 0,

(5.38)

where ak and bk (k = m for matrix in CCA; k = m, e for matrix and effective medium, respectively, in GSCM) are constants to be determined. For CCA, the constants am and bm need to be determined from Eq. (5.37) at ρ = ρ1 and the boundary conditions in Eq. (5.35) at ρ = ρ0 . For GSCM, the constants ak and bk (k = m, e) need to be determined from the remote boundary conditions in Eq. (5.37) and the boundary and the interface conditions in Eqs. (5.35) and (5.36). After the constants are obtained, the effective plane-strain bulk modulus of the nanochannel-array material can be calculated. As for the effective bulk modulus of a medium containing spherical nano-inhomogeneities (Eq. (5.6)), here it is found that both CCA and GSCM give the same prediction of k¯ for the nanochannel-array material k¯ =

∗ ] μTm [2(1 − f )km + (km + fμTm )C2222 , ∗ 2fkm + μTm [2 + (1 − f )C2222 ]

(5.39)

m m )/2 and μ m m + C2233 where km = (C2222 Tm = (C2222 − C2233 )/2, and the nondi∗ s mensional parameters Cklrs = Cklrs /(ρ0 μTm ) have been introduced here and for use below. f denotes the porosity.


51

¯ L and ¯ L and Poisson’s ratio ν¯ L . To determine E (b) Longitudinal Modulus E 0 ν¯ L , we apply a nonvanishing strain component εzz to the CCA and GSCM models. Then in the cylindrical coordinate system, the displacement field for CCA and the remote boundary conditions for GSCM can be expressed as u0ρ = 0,

u0φ = 0,

u0z = ε0zz z.

(5.40)

¯ L and ν¯ L The general expressions of the displacement components to determine E are bk (5.41) ukρ = ak ρ + , ukφ = 0, ukz = ε0zz z, ρ where again, ak and bk (k = m for CCA; k = m, e for GSCM) are constants to be determined. For CCA, the constants am and bm need to be determined from Eq. (5.40) at ρ = ρ1 and the boundary conditions in Eq. (5.35) at ρ = ρ0 . For GSCM, the constants ak and bk (k = m, e) need to be determined from the remote boundary conditions in Eq. (5.40) and the boundary and the interface conditions in Eqs. (5.35) and (5.36). It is found that both CCA and GSCM give the same ¯ L and ν¯ L predictions of E ¯ L = (1 − f )nm + E

∗ ) 4f(1 − f )km νLm (−2km νLm + μTm C1122 2 , (5.42) − 4k¯ ν¯ L ∗ 2fkm + μTm [2 + (1 − f )C2222 ]

∗ ∗ )νLm + (μTm + km )C1122 (1 − f)(2km − μTm C2222 , ∗ 2(1 − f)km + (km + fμTm )C2222 (5.43) m /(2k ). and νLm = C1122 m

ν¯ L = (1 − f)νLm + f m where nm = C1111

(c) Longitudinal Shear Modulus μ ¯ L . To predict μ ¯ L , the following displacement field in the cylindrical coordinate system is imposed on the outer boundary of the CCA model and at infinity in the GSCM model: u0ρ = ε0xz z cos φ,

u0φ = −ε0xz z sin φ,

u0z = ε0xz ρ cos φ,

(5.44)

where ε0xz is the only nonvanishing strain component. For CCA and GSCM, the general displacement solutions to determine μ ¯ L are ukρ = ε0xz z cos φ,

ukφ = −ε0xz z sin φ,

ukz = ε0xz (ak ρ +

bk ) cos φ, ρ

(5.45)

where ak and bk (k = m for CCA; k = m, e for GSCM) are constants to be determined. For CCA, the constants am and bm need to be determined from Eq. (5.44)

52

H. L. Duan et al.

at ρ = ρ1 and the boundary conditions at ρ = ρ0 in Eq. (5.35). For GSCM, the constants ak and bk (k = m, e) need to be determined from the remote boundary conditions in Eq. (5.44) and the boundary and interface conditions in Eqs. (5.35) and (5.36). Again, it is found that CCA and GSCM give the same predictions of μ ¯L ∗ (1 − f)μLm + (1 + f)μTm C1212 μ ¯ L = μLm , (5.46) ∗ (1 + f)μLm + (1 − f)μTm C1212 m . where μLm = C1212

(d) Transverse Shear Modulus μ ¯ T . As the composite cylinder assemblage model (CCA) only gives bounds on the effective transverse shear modulus, we only use the GSCM to calculate μ ¯ T . For this, as in the work of Christensen and Lo (1979), the imposed remote strain field in this model is chosen as ε0xx = −ε0yy = ε0T , and the corresponding remote displacements (ρ → +∞) in the cylindrical coordinate system are u0ρ = ε0T ρ cos 2φ,

u0φ = −ε0T ρ sin 2φ,

u0z = 0.

(5.47)

The general displacement solutions for the matrix and the effective medium in GSCM are 1 + ςk dk k

2 fk − 4 ρ, (5.48) uρ = −2 cos 2φ (1 − ςk )ak r + bk − r 2 r ςk dk = 2 sin 2φ (2 + ςk )ak r + bk − 2 fk + 4 ρ, r r

ukφ

2

(5.49)

where ςk = μTk /kk , (k = m, e), r = ρ/ρ0 . From the remote boundary conditions in Eq. (5.47) at ρ → ∞, we have ae = 0 and be = −ε0T /2. According to Eq. (4.14), μ ¯ T can be obtained from the following expression: μ ¯ T = μTm (1 −

¯ xx f ε¯ xx1 fϒ )+ , 0 εT 2ε0T

(5.50)

¯ in the x-direction, with ε¯ 1 ¯ xx are the components of ε¯ 1 and ϒ where ε¯ xx1 and ϒ ¯ and ϒ defined by m m 1 ¯ = 1 u ⊗ n + n ⊗ um d, ϒ σ · n ⊗ x d, (5.51) ε¯ 1 = 2S S where is the surface of ρ = ρ0 and S is the cross-sectional area of a pore. There are six unknown constants in Eqs. (5.48) and (5.49) and two unknown material


53

parameters μ ¯ T and k¯ to be determined from six boundary and interface conditions in Eqs. (5.35), (5.36), and (5.50). Following the procedure for composites with the surface/interface stress effect for the spherical nano-inhomogeneities (Eq. (5.16)), it can be shown that the constant ce related to ςe should vanish, which furnishes an additional condition. As in the conventional composites and in the composites with nano-inhomogeneities, the transverse effective shear modulus of the nanochannelarray material predicted by the GSCM is calculated from a quadratic equation in terms of μ ¯ T /μTm , which is similar to Eq. (5.16), that is, μ ¯T 2 μ ¯T + c = 0, + b (5.52) a μTm μTm where a , b , and c are functions of the volume fractions and elastic moduli of the inhomogeneity, matrix, and interface. ¯ ν¯ L , E ¯ L, μ ¯ L , and μ ¯ T that the effective It is seen from the expressions of k, elastic constants of nanochannel-array materials with parallel cylindrical pores s /μ . When the effective are governed by the intrinsic length scales lklrs = Cklrs Tm elastic constants are normalized by those of the matrix material, they become functions of the ratios of the intrinsic lengths to the characteristic length of the s material, that is, the radius ρ0 of the nanopores. When Cklrs → 0 or ρ0 → ∞, the results degenerate into the classical ones (without the surface stress effect). 5.3.2. Tailoring of Elastic Moduli of Nanochannel-array Materials When the matrix and the surface of the cylindrical pores are both isotropic, k¯ can be obtained from Eqs. (5.39) and (2.6), (1 − 2νm ) [2(1 − f) + (1 + f − 2fνm )A] k¯ = km , 2(1 + f − 2νm ) + (1 − f)(1 − 2νm )A

(5.53)

where A = (λs + 2μs )/(ρ0 μm ) is a mixed parameter related to the surface elastic properties and the radius ρ0 of the pores. Note that A becomes vanishingly small when the surface stress effect is negligible which is true when the pore radius ρ0 becomes large; Eq. (5.53) then gives the effective bulk modulus of a conventional cellular material that is always smaller than km . However, it is clear from Eq. (5.53) that if A exceeds a critical value Acr , the elastic modulus of a nanocellular material will exceed that of the matrix material. This critical value Acr is independent of the porosity and is simply 2 . (5.54) Acr = (1 − 2νm ) If the Poisson ratio of the matrix material is νm = 0.3, then the critical value Acr is 5 so that the combined surface elastic modulus λs + 2μs = 5ρ0 μm . For aluminium,

54

H. L. Duan et al.

μm = 34.7 GPa so that λs + 2μs should reach 347 N/m for the nanocellular material with ρ0 = 2 nm to be stiffer than the nonporous counterpart. The combined surface elastic modulus λs + 2μs of aluminium obtained by molecular dynamic simulations is in the order 10 N/m (Miller and Shenoy, 2000). This surface elastic modulus is nowhere near enough to make nanocellular aluminium stiffer than nonporous Al. However, the surface elastic constants can be enhanced by, for example, chemical modification of the pore surface, as mentioned above, or a parent material with a smaller Poisson ratio can be chosen to achieve the stiffening effect. For instance, if the Poisson ratio of the parent material is close to zero, then the stiffening effect is possible when Acr is just 2. If the parent material has a negative Poisson ratio, then Acr is further reduced and a much more manageable combined surface elastic modulus λs + 2μs is needed to achieve the stiffening of the parent material. The effective longitudinal shear modulus μ ¯ L of the nanocellular material, which determines its resistance to shearing along the direction of the pores, can be obtained from Eq. (5.46) μ ¯ L = μm

[1 − f + (1 + f)B] . [1 + f + (1 − f)B]

(5.55)

The mixed surface parameter is B = μs /(ρ0 μm ). It is easy to see that there also exists a critical value Bcr = 1, and when B > Bcr , the effective longitudinal shear modulus of the nanocellular material will exceed that of the parent counterpart. The surface elastic constant μs needs to be larger than ρ0 μm to achieve the stiffening effect. In practical applications such as in aerospace engineering, the specific stiffness, that is, stiffness/density ratio, of a material is very important. The ratio of the specific shear stiffness of the nanoporous material (which is critical to the cores of sandwich panels), denoted by μ∗L and calculated from Eq. (5.55), to that of the nonporous solid, denoted by μ∗m , is μ∗L μ ¯L 1 = , ∗ μm (1 − f) μm

(5.56)

where μ ¯ L is given by Eq. (5.55). The variation of μ∗L /μ∗m with the porosity f and the mixed surface parameter B is shown in Fig. 5.6. It is seen that μ∗L /μ∗m > 1 can be obtained for even small values of B. The transverse plane-strain bulk modulus ¯ T are very important for the in-plane stiffness k¯ and the related Young modulus E and thus the stability of a sandwich panel with pores perpendicular to the facets. ∗ and E∗ /E∗ with the porosity f and the mixed surface The variations of k∗ /km m T parameter A are similar to that of μ∗L /μ∗m . Thus, they are not shown here for brevity.


55

2.5

␮*L/ ␮*m

2.0 1.5 1.0 0.0 0.1 0.2 0.3 4 0. 0.5 6 0. f

1.00 0.7 0.50 5 0.25 0.00 B

The ratio μ∗L /μ∗m of the specific effective longitudinal shear modulus of a nanocellular material to that of the nonporous solid versus the porosity f and the surface property B. The light-shaded area represents the region where μ∗L /μ∗m < 1 and the dark-shaded area the region where μ∗L /μ∗m > 1. Reprinted from Duan et al. (2006c) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK.

Fig. 5.6

An alternative route to achieving the stiffening of a transversely isotropic nanocellular material is by coating the cylindrical pore surfaces. It has been be proved (e.g., Wang et al., 2005) that the effect of the surface elasticity is equivalent to that of a thin surface layer on the pore surface. In this case, λs and μs are given by Eq. (5.33). Therefore, by a proper choice of the properties and thickness of a coating layer, materials with cylindrical nanopores can be designed to be stiffer than their nonporous counterparts. For coated cylindrical pores, the effective elastic constants are still given by Eqs. (5.53) and (5.55) but with different expressions for the parameters A and B obtained from Eq. (5.33) A=

t μc 2 , (1 − νc ) ρ0 μm

B=

t μc . ρ0 μm

(5.57)

The critical value Acr for surface stiffening is still given by Eq. (5.54), and Bcr is still equal to 1. If we let νc = 0.3, t = 1 nm, and ρ0 = 10 nm, then when the shear ¯ L > μm . modulus ratio μc /μm exceeds 17.5, k¯ > km ; when μc /μm exceeds 10, μ From the theoretical analysis mentioned above, it can be seen that the stiffening effect can be easily obtained by surface coating. Moreover, the ratios of the specific effective moduli of nanoporous materials to those of the nonporous solids can be written in the general form k∗ k¯ = , ∗ km 1 km

μ∗L μ ¯L = , ∗ μm 1 μm

μ∗T μ ¯T = , ∗ μm 1 μm

(5.58)

56

H. L. Duan et al.

where ζI 1 = 1 − f + f ζ

(

) 2t t2 + 2 , ρ0 ρ0

(5.59)

where ζI and ζ are the densities of the coating and the matrix, respectively. As can be seen from Eqs. (5.57)–(5.59), the stiffness of the nanoporous materials is only dependent on the ratio t/ρ0 of the coating thickness to the radius of the pores, and not dependent on the absolute size of the pores. Therefore, the application of the second route is not limited to the nanoporous materials. The same procedures can be used to improve the stiffness of the micro- and macroporous materials. To show the effect of the coating, the variation of μ∗L /μ∗m calculated from Eq. (5.58) versus the porosity f and the mixed surface parameter B is plotted in Fig. 5.7. The parameters used in Fig. 5.7 are t/ρ0 = 0.1 and ζI /ζ = 1. It is seen that μ∗L /μ∗m > 1 can be obtained at a small value of B. If the material of the coating has a smaller density, μ∗L /μ∗m will be larger than that shown in Fig. 5.7. The above procedures to increase the stiffness of the nanoporous materials can find applications in many areas of industry. Sandwich panels used in many industrial applications contain cellular cores, for example, honeycombs, with pores aligned perpendicular to the facets (Gibson and Ashby, 1997). The shear rigidity of such panels and therefore their resistance to shape change are determined by the effective longitudinal shear modulus in Eq. (5.55) of the cellular cores. Thus, a cellular core with a high shear modulus has great potential in the fabrication of lightweight sandwich structures which are vital for aerospace engineering and other transport industries. Although the microstructures of nanoporous materials

␮*L / ␮*m

2

1

0.0 0.1 .2 0 0.3 .4 0 0.5 .6 0 f

1.00 0.75 0.50 0.25 0.00 B

Fig. 5.7 The ratio μ∗L /μ∗m of the specific effective longitudinal shear modulus of a nanocellular material to that of the nonporous solid versus the porosity f and the surface property B (t/ρ0 = 0.1, ζI /ζ = 1). The light-shaded area represents the region where μ∗L /μ∗m < 1 and the dark-shaded area the region where μ∗L /μ∗m > 1. Reprinted from Duan et al. (2006c) with acknowledgment to Elsevier Science Ltd, The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK.


57

are not exactly the same as those of the conventional honeycombs, the analysis reported here can be regarded as a first step towards increasing the stiffness of porous materials by surface modification.

6. Scaling Laws for Properties of Nanostructured Materials The study of the variation of the properties of materials with their geometrical feature size has a long history because of its importance in many fields. The interest has been heightened recently at the nanoscale because nanostructures are pervasive in nature (Kamat et al., 2000; Gao et al., 2003) and in modern industry (Goldstein et al., 1992; Streitz et al., 1994; Bertsch, 1997; Miller and Shenoy, 2000; Miyata et al., 2004), and the large ratio of surface atoms to the bulk can have a profound effect on their properties. In physics and chemistry, the effect of particle size on melting and evaporation temperatures has been discussed since 1900s, and this effect is not restricted to any particular material; rather, it is observed in a variety of materials from metals and alloys to semiconductors and semi-crystalline lamellar polymers, and the typical size range over which the melting temperature undergoes a large change is 2–20 nm (Pawlow, 1909; Buffat and Borel, 1976; Couchman and Jesser, 1977; Castro et al., 1990; Peters et al., 1998; Zhao et al., 2001; Nanda et al., 2002b; Dick et al., 2002; Sun et al., 2002; Jesser et al., 2004). Many phenomena in solidstate physics and materials science also exhibit size dependence. For example, reduction in the size of solids also results in a change of their failure mode. When the size of brittle calcium carbonate particles is reduced to a critical value of 850 nm, comminuting becomes impossible (Kendall, 1978; Karihaloo, 1979) and the particles behave as if they were ductile. As shown in the previous sections, surface/interface stress has a profound effect on the properties of nanostructured materials due to the large ratio of surface/interface atoms to the bulk. The properties of the nanostructured materials are affected by the energy competition between the surface and bulk, and a common feature of many physical properties is that when the characteristic size of the object is very large, the physical property under consideration tends to that of the bulk material. By dimensional analysis, the ratio of a physical property at a small size L, denoted by F(L), to that of the bulk, denoted by F (∞), can be expressed as a function of some nondimensional variables Xj (j = 1, . . . , M) and a nondimensional parameter lin /L related to the size F(L) = H(Xj , lin /L), F(∞)

(6.1)

where lin is an intrinsic length scale related to the surface property, and L is the feature size of the object under consideration. We will confirm below that for many

58

H. L. Duan et al.

physical properties the function in Eq. (6.1) can be expanded in powers of lin /L. When the intrinsic length scale lin is small compared with the characteristic size L, we need only retain the linear term. As a result, the size dependence of the properties of materials can be captured accurately by the following simple scaling law: lin F(L) =1+P , F(∞) L

(6.2)

where P is a nondimensional parameter. In what follows, we shall confirm that the scaling law Eq. (6.2) is obeyed by many properties, for example, elastic moduli, thermal conductivity, melting temperature, etc.

6.1. Elastic Properties with Surface Stress Effect For the deformation of homogeneous nanostructured materials, for example, the extension of nanoplates, nanobeams, nanowires, etc., when the surface elasticity, characterized by the surface elastic constant τ, is taken into account, an intrinsic length scale automatically emerges (Miller and Shenoy, 2000; Shenoy, 2002), lin = τ/E,

(6.3)

where E is the Young modulus of the bulk material. Thus, the nondimensional mechanical properties of nanostructures are governed by the scaling law (6.2) with lin given by Eq. (6.3). For metals and some other materials, lin in Eq. (6.3) is typically in the order of 0.01–0.1 nm (Streitz et al., 1994; Miller and Shenoy, 2000). Thus, the scaling law (6.2) can be expected to give good predictions for L >3–5 nm. Ab initio and molecular dynamic simulations and experimental results show that the elastic constants of nanoplates, nanobeams, and nanowires obey the scaling law (6.2) almost exactly in and above the range 1–100 nm (Miller and Shenoy, 2000; Shenoy, 2002; Zhou and Huang, 2004; Cuenot et al., 2004; Villain et al., 2004). In particular, according to Eqs. (6.2) and (6.3), the Young modulus of a nanoplate can be expressed as τ 1 E(L) =1+P , E(∞) a0 E(∞) N

(6.4)

where a0 is the lattice spacing, N is the number of atomic layers along the nanoplate thickness. The elastic constants of nanoplates of copper and tungsten obtained from atomistic calculations by Zhou and Huang (2004) and Villain et al. (2004) are shown in Fig. 6.1. It is seen that the ratio E/E(∞) for these materials almost exactly obeys the scaling law in Eq. (6.2) (or Eq. (6.4)). Zhou and


59

1.3 1.2 E/E(`)

1.1 1.0 0.9 0.8 0.7 0.00

{001}/, Cu {111}/, Cu {001}/, Cu {100}/, W

0.05

0.10 1/N

0.15

0.20

Fig. 6.1 Normalized Young modulus versus the inverse of the number of atomic layers (N) along the nanoplate thickness. The data for Cu from Zhou and Huang (2004) and those for W from Villain et al. (2004) are obtained from atomistic calculations. {·} denotes a group of crystallographic planes and · denotes a group of crystallographic directions. Reprinted from Wang et al. (2006) with acknowledgment to The Royal Society, 6-9 Carlton House Terrace, London SW1Y 5AG, England.

Huang (2004) and Villain et al. (2004) did not explicitly use the concept of surface elastic constant to explain the variation of the elastic constants with the thickness of the nanoplates, but, obviously, the surface stress effect is implicitly taken into account in the atomistic calculations. These computations provide a further objective justification of the scaling law (6.2). Moreover, had this scaling law been known, the numerical computations could have been significantly reduced, as only two points are needed to determine a linear function. This is particularly important in the problems of characterization of heterogeneous materials given below for which it may be very difficult and/or time-consuming to perform atomistic simulations. For general heterogeneous nanostructured materials, the elasticity of an isotropic surface is characterized by two surface elastic constants λs and μs , giving rise to two intrinsic length scales lλ =λs /μ and lμ =μs /μ (Duan et al., 2005a,b), where μ is the shear modulus of the bulk material. Thus, the size dependence of nondimensional physical properties associated with the deformation problems of heterogeneous nanosolids can be expected to follow a scaling law similar to Eq. (6.2) but with an intrinsic length scale that is a linear combination of these two scales: F(L) 1 = 1 + (αlλ + βlμ ). F(∞) L

(6.5)

Here, α and β are two nondimensional parameters, F(L) is the property corresponding to a characteristic size L at nanoscale, and F (∞) denotes the same property

60

H. L. Duan et al.

when L→ ∞ or, equivalently, when the surface stress effect is vanishingly small. The scaling law (6.5) is applicable to a wide variety of properties, for example, the maximum stress concentration factor at the boundary of a circular nanopore in a plate under uniaxial tension, the effective elastic moduli of the nanochannel-array material, the Eshelby tensor of a spherical inhomogeneity, and the effective CTE of heterogeneous materials containing aligned cylindrical nanopores, etc. (Wang, et al., 2006; Duan and Karihaloo, 2007). For example, the scaling law of the maximum stress concentration factor k(ρ0 ) at the boundary of a circular nanopore of radius ρ0 in a plate (for the plane stress case) under uniaxial tension (χ = 0) can be determined from Eq. (3.4), that is, 7(lλ + 2lμ ) k(ρ0 ) , =1− k(∞) 3ρ0

(6.6)

where k(∞)=3 is the classical elasticity result. We compare the exact result given by Eq. (3.4) with the scaling law in Eq. (6.6), and the results are shown in Fig. 6.2, where “A” and “B” denote the two sets of surface property parameters given in Section 3.1, and the material of the plate is aluminium. It is seen that the scaling law is very accurate. We have seen above that an isotropic surface/interface is characterized by two surface/interface elastic constants κs and μs , giving rise to two intrinsic length scales lκ = κs /μm and lμ = μs /μm . For many materials, for instance, metals, the intrinsic length scales lκ and lμ are in the order of 0.01–0.1 nm. Thus, the surface/interface stress effect will only become significant at the nanoscale, as evidenced by the elastic moduli of Ag and Pb nanowires (Cuenot et al., 2004)

k (␳0) /k (⬁)

1.3

A, exact A, scaling law B, exact B, scaling law

1.2 1.1 1.0 0.9 0.8

1

5

10

15 20 ␳0 (nm)

25

30

Fig. 6.2 Comparison of the scaling law (Eq. (6.6)) and the exact result of the maximum stress concentration factor k(ρ0 )/k(∞) at the boundary of a circular nanopore of radius ρ0 in a plate (aluminium) under uniaxial tension. A: κs = −5.457 N/m, μs = −6.2178 N/m for the surface [1 0 0]; B: κs = 12.932 N/m, μs = −0.3755 N/m for the surface [1 1 1].


61

and the effective elastic constants of heterogeneous solids containing nanovoids (Duan et al., 2005a). It is seen from Section 2 that the Eshelby tensors and the stress concentration tensors are all functions of the ratios between these intrinsic length scales and the size of the inhomogeneity, namely κsr = lκ /R and μrs = lμ /R. Thus, when R is sufficiently large compared with these intrinsic length scales, say R > 3 nm, the nondimensional parameters κsr = lκ /R and μrs = lμ /R will be small. We can then expand the components of the Eshelby and stress concentration tensors in terms of these small nondimensional parameters and retain only the linear terms. In this way, we can obtain a very simple scaling law for the Eshelby and stress concentration tensors. Here, we only show the details of the scaling law for the interior Eshelby tensor for a spherical inhomogeneous inclusion: SI (x) = SI (∞) + SI (R, x)

(6.7)

with SI (R, x) =

α(x)lκ + β(x)lμ . R

(6.8)

Here, SI (∞) is the classical interior Eshelby tensor for a spherical inhomogeneous inclusion, and α(x) and β(x) are two position-dependent tensors. SI (∞) is still given by Eqs. (2.17) and (2.22) but with A, F , and B in Eq. (2.22) replaced with A∞ , F∞ , and B∞ , respectively, A∞ = 0, B∞

F∞ = −

2 (1 − 2νI ) , [η (1 3 + νI ) + 2 (1 − 2νI )]

(7 − 5νm ) = . 3 [−7 + 5ν2 − 2η(4 − 5νm )]

(6.9)

By comparing the values of the components of the Eshelby tensor in Eq. (6.7) with the exact values given in Eq. (2.17) together with the expression in Eq. (2.22), it can be confirmed that the scaling law Eq. (6.7) gives very accurate results for lκ < 0.1 nm, lμ < 0.1 nm, and R > 3 nm. The exterior Eshelby and stress concentration tensors can also be shown to follow scaling laws similar to that in Eq. (6.7). They will not be reproduced here. Many physical properties with the surface/interface stress effect can be shown to obey similar scaling laws, for example, the effective moduli of heterogeneous solids containing nano-inhomogeneities obtained by various micromechanical homogenization schemes (Duan et al., 2005a).

62

H. L. Duan et al.

6.2. Melting Temperature The size dependence of the melting temperature at nanoscale has enormous implications in the production of nanocrystals and thin films and in the thermal stability of QDs (Goldstein et al., 1992). A large body of test data has been accumulated on this size dependence, and a number of theoretical models have been proposed to explain it (Buffat and Borel, 1976; Couchman and Jesser, 1977; Castro et al., 1990; Peters et al., 1998; Zhao et al., 2001; Nanda et al., 2002b; Dick et al., 2002; Sun et al., 2002). It has been demonstrated that the size-dependent melting temperature T(R) of spherical nanoparticles with radius R precisely obeys a scaling law similar to Eq. (6.2), T(R) lin =1−2 , T(∞) R

(6.10)

where lin is given in the paper of Wang et al. (2006). Similar to lin due to the surface elasticity (e.g., Eq. (6.3) or Eq. (6.5)), lin for the melting temperature is also from the contribution of the surface/interface energy. In fact, Eq. (6.10) is actually the Gibbs–Thomson equation following from consideration of the relative thermodynamic contributions of surface and bulk energies. It lends theoretical support to the scaling law Eq. (6.2). For example, the intrinsic length scale lin is in the order of 0.01–0.1 nm for Au and Ag nanoparticles. This value of lin is also true for many other metals. Therefore, the scaling law Eq. (6.10) can be expected to give good predictions for L >3–5 nm. The scaling law not only captures the sizedependent reduction in the melting temperature of unconstrained nanoparticles but also if they are embedded in a matrix. Recently, it has been confirmed that the size-dependent evaporation temperature of nanoparticles (Nanda et al., 2002a) also follows the scaling law (6.2). Moreover, if nanostructured materials are embedded in a matrix and the interfaces between them and the surrounding matrix are coherent or semi-coherent, then the melting temperature actually increases with decreasing nanoparticle size (Zhao et al., 2001).

7. Conclusions This article summarized the recent solutions of some fundamental problems in mechanics of heterogeneous materials where the surface/interface stress is taken into account. These include the Eshelby tensors, stress concentration tensors and their applications, the micromechanical framework, the novel properties of nanochannel-array materials, and the generalized Levin’s formula and Hill’s connections. These solutions show that the surface/interface stress has an important


63

effect on the mechanical properties of materials at the nanoscale. When the surface/interface elasticity is taken into account, some length scales emerge automatically. Thus, unlike their classical counterparts, the mechanical properties at the nanoscale become size dependent. Scaling laws governing the properties of nanostructured materials have also been derived. It should be emphasized that this paper has considered the elastic deformation only. For inelastic nanostructured materials, the situation is partly similar in so far as the effect of surface stress is concerned, but there may be additional length scales and size effects. This will need further investigation in the future.

Acknowledgment Duan is funded by a Post-doctoral Fellowship from The Royal Society, London. Wang acknowledges the support of the National Natural Science Foundation of China under Grant No. 10525209. Helpful discussions with Professor Zhuping Huang of Peking University are gratefully acknowledged. References Aboudi, J. (1991). Mechanics of Composite Materials: A Unified Micromechanical Approach. Elsevier, New York. Bailey, R. E., and Nie, S. M. (2003). Alloyed semiconductor quantum dots: tuning the optical properties without changing the particle size. J. Am. Chem. Soc. 125, 7100–7106. Benveniste, Y. (1985). The effective mechanical behaviour of composite materials with imperfect contact between the constituents. Mech. Mater. 4, 197–208. Benveniste, Y. (1987). A new approach to the application of Mori-Tanaka’s theory in composite materials. Mech. Mater. 6, 147–157. Benveniste, Y. (2006). A general interface model for a three-dimensional curved thin anisotropic interphase between two anisotropic media. J. Mech. Phys. Solids 54, 708–734. Benveniste, Y., and Miloh, T. (2001). Imperfect soft and stiff interfaces in two-dimensional elasticity. Mech. Mater. 33, 309–323. Bertsch, G. (1997). Melting in clusters. Science 277, 1619–1619. Bottomley, D. J., and Ogino, T. (2001). Alternative to the Shuttleworth formulation of solid surface stress. Phys. Rev. B 63, 165412-1–5. Buffat, Ph., and Borel, J.-P. (1976). Size effect on the melting temperature of gold particles. Phys. Rev. A 13, 2287–2298. Cahn, J. W. (1978). Thermodynamics of solid and fluid surfaces. In Interfacial Segregation (W. C. Johnson, and J. M. Blakely, Eds.), pp. 3–23. American Society for Metals, Metals Park, Ohio. Cammarata, R. C. (1994). Surface and interface stresses effects in thin films. Prog. Surf. Sci. 46, 1–38. Cammarata, R. C. (1997). Surface and interface stress effects on interfacial and nanostructured materials. Mater. Sci. Eng. A 237, 180–184. Castro, T., Reifenberger, R., Choi, E., and Andres, R. P. (1990). Size-dependent melting temperatures of individual nanometer-sized metallic clusters. Phys. Rev. B 42, 8548–8556. Chen, T. Y., and Dvorak, G. J. (2006). Fibrous nanocomposites with interface stress: Hill’s and Levin’s connections for effective moduli. Appl. Phys. Lett. 88, 211912-1–3.

64

H. L. Duan et al.

Chen, T. Y., Dvorak, G. J., and Yu, C. C. (2007a). Solids containing spherical nano-inclusions with interface stresses: effective properties and thermalmechanical connections. Int. J. Solids Struct. 44, 941–955. Chen, T. Y., Dvorak, G. J., and Yu, C. C. (2007b). Size-dependent elastic properties of unidirectional nano-composites with interface stresses. Acta Mech. 188, 39–54. Chen, X. B., Lou, Y. B., Samia, A. C., and Burda, C. (2003). Coherency strain effects on the optical response of core/shell heteronanostructures. Nano Lett. 3, 799–803. Christensen, R. M., and Lo, K. H. (1979). Solutions for effective shear properties in three phase sphere and cylinder models. J. Mech. Phys. Solids 27, 315–330. Couchman, P. R., and Jesser, W. A. (1977). Thermodynamic theory of size dependence of melting temperature in metals. Nature 269, 481–483. Cuenot, S., Fr’etigny, C., Demoustier-Champagne, S., and Nysten, B. (2004). Surface tension effect on the mechanical properties of nanomaterials measured by atomic force microscopy. Phys. Rev. B 69, 165410–165413. Diao, J. K., Gall, K., and Dunn, M. L. (2004). Atomistic simulation of the structure and elastic properties of gold nanowires. J. Mech. Phys. Solids 52, 1935–1962. Dick, K., Dhanasekaran, T., Zhang, Z. Y., and Meisel, D. (2002). Size-dependent melting of silicaencapsulated gold nanoparticles. J. Am. Chem. Soc. 124, 2312–2317. Dingreville, R., and Qu, J. (2007). A semi-analytical method to compute surface elastic properties. Acta Mater. 55, 141–147. Dingreville, R., Qu, J., and Cherkaoui, M. (2005). Surface free energy and its effect on the elastic behavior of nano-sized particles, wires and films. J. Mech. Phys. Solids 53, 1827–1854. Duan, H. L. (2005). Interface Effect in Mechanics of Heterogeneous Materials. PhD Thesis, Department of Mechanics and Engineering Science, Peking University, Beijing. Duan, H. L., and Karihaloo, B. L. (2007). Thermo-elastic properties of heterogeneous materials with imperfect interfaces: generalized Levin’s formula and Hill’s connections. J. Mech. Phys. Solids 55, 1036–1052. Duan, H. L., Karihaloo, B. L., Wang, J., and Yi, X. (2006a). Strain distributions in nano-onions with uniform and non-uniform compositions. Nanotechnology 17, 3380–3387. Duan, H. L., Karihaloo, B. L., Wang, J., and Yi, X. (2006b). Compatible composition profiles and critical sizes of alloyed quantum dots. Phys. Rev. B 74, 195328-1–4. Duan, H. L., Wang, J., Huang, Z. P., and Karihaloo, B. L. (2005a). Eshelby formalism for nanoinhomogeneities. Proc. R. Soc. Lond. A 461, 3335–3353. Duan, H. L., Wang, J., Huang, Z. P., and Karihaloo, B. L. (2005b). Sizedependent effective elastic constants of solids containing nano-inhomogeneities with interface stress. J. Mech. Phys. Solids 53, 1574–1596. Duan, H. L., Wang, J., Karihaloo, B. L., and Huang, Z. P. (2006c). Nanoporous materials can be made stiffer than non-porous counterparts by surface modification. Acta Mater. 54, 2983–2990. Dvorak, G. J. (1990). On uniform-fields in heterogeneous media. Proc. R. Soc. A 431, 89–110. Eshelby, J. D. (1956). The continuum theory of lattice defects. Solid State Phys. 3, 79–144. Eshelby, J. D. (1957). The determination of the elastic field of an ellipsoidal inclusion and related problems. Proc. R. Soc. Lond. A 241, 376–396. Eshelby, J. D. (1959). The elastic field outside an ellipsoidal inclusion. Proc. R. Soc. Lond. A 252, 561–569. Fang, Q. H., and Liu, Y. W. (2006). Size-dependent interaction between an edge dislocation and a nanoscale inhomogeneity with interface effects. Acta Mater. 54, 4213–4220. Faux, D. A., and Pearson, G. S. (2000). Green’s tensors for anisotropic elasticity: application to quantum dots. Phys. Rev. B 62, 4798–4801. Fried, E., and Gurtin, M. E. (2004). A unified treatment of evolving interfaces accounting for small deformations and atomic transport with emphasis on grainboundaries and epitaxy. Adv. Appl. Mech. 40, 1–177.


65

Gao, H., Ji, B., Jäger, I. L., Arzt, E., and Fratzl, P. (2003). Materials become insensitive to flaws at nanoscale: lessons from nature. Proc. Natl. Acad. Sci. 100, 5597–5600. Gao, W., Yu, S. W., and Huang, G. Y. (2006). Finite element characterization of the size-dependent mechanical behaviour in nanosystems. Nanotechnology 17, 1118–1122. Gibbs, J. W. (1906). The Scientific Papers of J. Willard Gibbs, vol. 1. Longmans-Green, London. Gibson, L. J., and Ashby, M. F. (1997). Cellular Solids – Structure and Properties, Second Edition. Cambridge University Press, Cambridge. Gleiter, H. (2000). Nanostructured materials: basic concepts and microstructure. Acta Mater. 48, 1–29. Goldstein, A. N., Echer, C. M., and Alivisatos, A. P. (1992). Melting in semiconductor nanocrystals. Science 256, 1425–1427. Gosling, T. J., and Willis, J. R. (1995). Mechanical stability and electronic properties of buried strained quantum wire arrays. J. Appl. Phys. 77, 5601–5610. Gurtin, M. E., and Murdoch, A. I. (1975). A continuum theory of elastic material surfaces. Arch. Ration. Mech. Anal. 57, 291–323. Gurtin, M. E., and Murdoch, A. I. (1978). Surface stress in solids. Int. J. Solids Struct. 14, 431–440. Gurtin, M. E.,Weissmüller, J., and Larché, F. (1998). A general theory of curved deformable interfaces in solids at equilibrium. Philos. Mag. A 78, 1093–1109. Hashin, Z. (1962). The elastic moduli of heterogeneous materials. J. Appl. Mech. 29, 143–150. Hashin, Z. (1991). Thermoelastic properties of particulate composites with imperfect interface. J. Mech. Phys. Solids 39, 745–762. Hashin, Z. (2002). The interphase/imperfect interface in elasticity with application to coated fiber composites. J. Mech. Phys. Solids 50, 2509–2537. Hashin, Z., and Rosen, B. W. (1964). The elastic moduli of fiber-reinforced materials. J. Appl. Mech. 31, 223C–232C. He, L. H. (2006). Self-strain of solids with spherical nanovoids. App. Phys. Lett. 88, 151909-1–3. He, L. H., and Lim, C. W. (2006). Surface Green function for a soft elastic half-space: influence of surface stress. Int. J. Solids Struct. 43, 132–143. Herring, C. (1953). The use of classical macroscopic concepts in surface energy problems. In Structure and Properties of Solid Surfaces (R. Gomer, and C. S. Smith, Eds.), pp. 5–81. The University of Chicago Press, Chicago. Hill, R. (1964). Theory of mechanical properties of fiber-strengthened materials–I. Elastic behavior. J. Mech. Phys. Solids 12, 199–212. Huang, Z. P., and Sun, L. (2007). Size-dependent effective properties of a heterogeneous material with interface energy effect: from finite deformation theory to infinitesimal strain analysis. Acta Mech. 190, 151–163. Huang, Z. P., and Wang, J. (2006). A theory of hyperelasticity of multi-phase media with surface/interface energy effect. Acta Mech. 182, 195–210. Huang, G. Y., and Yu, S. W. (2006). Effect of surface piezoelectricity on the electromechanical behaviour of a piezoelectric ring. Phys. Status Solidi B 243, R22–R24. Hu, G. K. (1996). A method of plasticity for general aligned spheroidal void or fiber-reinforced composites. Int. J. Plast. 12, 439–449. Ibach, H. (1997). The role of surface stress in reconstruction, epitaxial growth and stabilization of mesoscopic structure. Surf. Sci. Rep. 29, 195–263. Jesser, W. A., Shneck, R. Z., and Gile, W. W. (2004). Solid-liquid equilibria in nanoparticles of Pb-Bi alloys. Phys. Rev. B 69, 144121-1–13. Jing, G. Y., Duan, H. L., Sun, X. M., Zhang, Z. S., Xu, J., Li, Y. D., Wang, J., and Yu, D. P. (2006). Surface effects on elastic properties of silver nanowires: contact atomic-force microscopy. Phys. Rev. B 73, 235409-1–6. Kamat, S., Su, X., Ballarini, R., and Heuer, A. H. (2000). Structural basis for the fracture toughness of the shell of the conch Strombus gigas. Nature 405, 1036–1040. Karihaloo, B. L. (1979). Impossibility of comminuting small particles by compression. Nature 279, 169–170.

66

H. L. Duan et al.

Kendall, K. (1978). Impossibility of comminuting small particles by compression. Nature 272, 710–711. Kolesnikova, A. L., and Romanov, A. E. (2004). Misfit dislocation loops and critical parameters of quantum dots and wires. Philos. Mag. Lett. 84, 501–506. Levin, V. M. (1967). On the coefficients of thermal expansion of heterogeneous materials. Mech. Solids 2, 58–61. Li, Y. C., Ye, M. F., Yang, C. H., Li, X. H., and Li, Y. F. (2005). Compositionand shape-controlled synthesis and optical properties of ZnxCd1 – xS alloyed nanocrystals. Adv. Funct. Mater. 15, 433–441. Liang, Y. Q., Zhai, L., Zhao, X. S., and Xu, D. S. (2005). Band-gap engineering for semiconductor nanowires through composition modulation. J. Phys. Chem. B 109, 7120–7123. Luré, A. I. (1964). Three-dimensional Problems of Theory of Elasticity. Interscience, New York. Malachias, A., Kycia, S., Medeiros-Ribeiro, G., Magalhaes-Paniago, R., Kamins, T. I., and Williams, R. S. (2003). 3D composition of epitaxial nanocrystals by anomalous x-ray diffraction: observation of a Si-rich core in Ge domes on Si(100). Phys. Rev. Lett. 91, 176101-1–4. Martin, C. R., and Siwy, Z. (2004). Molecular filters-pores within pores. Nat. Mater. 3, 284–285. Masuda, H., and Fukuda, K. (1995). Ordered metal nanohole arrays made by a two-step replication of honeycomb structures of anodic alumina. Science 268, 1466–1468. Mi, C. W., and Kouris, D. A. (2006). Nanoparticles under the influence of surface/interface elasticity. J. Mech. Mater. Struct. 1, 763–791. Miller, R. E., and Shenoy, V. B. (2000). Size-dependent elastic properties of nanosized structural elements. Nanotechnology 11, 139–147. Milton, G. W. (2002). The Theory of Composites. Cambridge University Press, Cambridge. Miyata, H., Suzuki, T., Fukuoka, A., Sawada, T., Watanabe, M., Noma, T., Takada, K., Mukaide, T., and Kuroda, K. (2004). Silica films with a single-crystalline mesoporous structure. Nat. Mater. 3, 651–656. Mori, T., and Tanaka, K. (1973). Average stress in matrix and average elastic energy of materials with misfitting inclusions. Acta Mater. 21, 571–574. Müller, P., and Sául, A. (2004). Elastic effects on surface physics. Surf. Sci. Rep. 54, 157–258. Mura, T. (1987). Micromechanics of Defects in Solids. Dordrecht, Martinus Nijhoff. Murdoch, A. I. (1976). Thermodynamical theory of elastic-material interfaces. Q. J. Mech. Appl. Maths. 29, 245–275. Murdoch, A. I. (2005). Some fundamental aspects of surface modelling. J. Elast. 80, 33–52. Murr, L. E. (1975). Interfacial Phenomena in Metals and Alloys. Addison-Wesley, London. Nanda, K. K., Kruis, F. E., and Fissan, H. (2002a). Evaporation of free PbS nanoparticles: evidence of the Kelvin effect. Phys. Rev. Lett. 89, 256103-1–4. Nanda, K. K., Sahu, S. N., and Behera, S. N. (2002b). Liquid-drop model for the size-dependence melting of low-dimensional systems. Phys. Rev. A 66, 013208-1–8. Nemat-Nasser, S., and Hori, M. (1999). Micromechanics: Overall Properties of Heterogeneous Elastic Solids, Second Edition. North-Holland, Netherlands. Nix, W. D., and Gao, H. J. (1998). An atomic interpretation of interface stress. Scr Mater. 39, 1653–1661. Orowan, E. (1970). Surface energy and surface tension in solids and liquids. Proc. R. Soc. Lond. A 316, 473–491. Pathak, S., and Shenoy, V. B. (2005). Size dependence of thermal expansion of nanostructures. Phys. Rev. B 72, 113404-1–4. Pawlow, P. (1909). Über die abhängigkeit des schmelzpunktes von der oberflächenenergie eines festen körpers. Z. Phys. Chem. 65, 545–548. Peters, K. F., Cohen, J. B., and Chung, Y. W. (1998). Melting of Pb nanocrystals. Phys. Rev. B 57, 13430–13438. Ponte Castañeda, P., and Suquet, P. (1998). Nonlinear composites. Adv. Appl. Mech. 34, 171–302. Povstenko, Y. Z. (1993). Theoretical investigation of phenomena caused by heterogeneous surfacetension in solids. J. Mech. Phys. Solids 41, 1499–1514.


67

Qiu, Y. P., and Weng, G. J. (1992). A theory of plasticity for porous materials and particle-reinforced composites. J. Appl. Mech. 59, 261–268. Ren, Q., and Zhao, Y. P. (2004). Influence of surface stress on frequency of microcantilever-based biosensors. Microsyst. Technol. 10, 307–314. Rockenberger, J., Troger, L., Rogach,A. L., Tischer, M., Grundmann, M., Eychmuller,A., and Weller, H. (1998). The contribution of particle core and surface to strain, disorder and vibrations in thiolcapped CdTe nanocrystals. J. Chem. Phys. 108, 7807–7815. Rosenauer, A., and Gerthsen, D. (1999). Atomic scale strain and composition evaluation from highresolution transmission electron microscopy images. Adv. Imag. Elect. Phys. 107, 121–130. Rottman, C. (1988). Landau theory of coherent interphase interface. Phys. Rev. B 38, 12031–12034. Sharma, P., and Ganti, S. (2004). Size-dependent Eshelby’s tensor for embedded nano-inclusions incorporating surface/interface. J. Appl. Mech. 71, 663–671. Sharma, P., Ganti, S., and Bhate, N. (2003). Effect of surfaces on the sizedependent elastic state of nano-inhomogeneities. Appl. Phys. Lett. 82, 535–537. Shenoy, V. B. (2002). Size-dependent rigidities of nanosized torsional elements. Int. J. Solids Struct. 39, 4039–4052. Shenoy, V. B. (2005). Atomistic calculations of elastic properties of metallic fcc crystal surfaces. Phys. Rev. B 71, 094104-1–11. Shi, J. L., Hua, Z. L., and Zhang, L. X. (2004). Nanocomposites from ordered mesoporous materials. J. Mater. Chem. 14, 795–806. Shuttleworth, R. (1950). The surface tension of solids. Proc. Phys. Soc. A 63, 444–457. Spencer, B. J., and Blanariu, M. (2005). Shape and composition map of a prepyramid quantum dot. Phys. Rev. Lett. 95, 206101-1–4. Steigmann, D. J., and Ogden, R. W. (1999). Elastic surface-substrate interactions. Proc. R. Soc. Lond. A 455, 437–474. Streitz, F. H., Cammarata, R. C., and Sieradzki, K. (1994). Surface-stress effects on elastic properties. I. Thin metal films. Phys. Rev. B 49, 10699–10706. Sun, C. Q., Wang, Y., Tay, B. K., Li, S., Huang, H., and Zhang, Y. B. (2002). Correlation between the melting point of a nanosolid and the cohesive energy of a surface atom. J. Phys. Chem. 106, 10701–10705. Tersoff, J. (1998). Enhanced nucleation and enrichment of strained-alloy quantum dots. Phys. Rev. Lett. 81, 3183–3186. Torquato, S. (2002). Random Heterogeneous Materials: Microstructure and Macroscopic Properties. Springer-Verlag, New York. Vegard, L. (1921). The constitution of mixed crystals and the space occupied by atoms. Z. Phys. 5, 17–26. Villain, P., Beauchamp, P., Badawi, K. F., Goudeau, P., and Renault, P. O. (2004). Atomistic calculation of size effects on elastic coefficients in nanometresized tungsten layers and wires. Scr. Mater. 50, 1247–1251. Walpole, L. J. (1981). Elastic behaviour of composite materials: theoretical foundations. In Advances in Applied Mechanics, vol. 21 (Yih Chia-Shun, Ed.), pp. 169–242. Academic Press, New York. Wang, G. F., and Wang, T. J. (2006). Deformation around a nanosized elliptical hole with surface effect. Appl. Phys. Lett. 89, 161901-1–3. Wang, G. F., Wang, T. J., and Feng, X. Q. (2006). Surface effects on the diffraction of plane compressional waves by a nanosized circular hole. Appl. Phys. Lett. 89, 231923-1–3. Wang, J., Duan, H. L., Huang, Z. P., and Karihaloo, B. L. (2006). A scaling law for properties of nano-structured materials. Proc. R. Soc. Lond. A 462, 1355–1363. Wang, J., Duan, H. L., Zhang, Z., and Huang, Z. P. (2005). An antiinterpenetration model and connections between interphase and interface models in particle-reinforced composites. Int. J. Mech. Sci. 47, 701–718. Weissmüller, J., and Cahn, J. W. (1997). Mean stresses in microstructure due to interface stresses: a generalization of a capillary equation for solids. Acta Mater. 45, 1899–1906.

68

H. L. Duan et al.

Weissmüller, J., Viswanath, R. N., Kramer, D., Zimmer, P., Wurschum, R., and Gleiter, H. (2003). Charge-induced reversible strain in a metal. Science 300, 312–315. Willis, J. R. (2000). The overall response of nonlinear composite media. Eur. J. Mech. A/Solids 19, S165–S184. Zhang, T. Y. (1995). A dislocation in a compositionally graded epilayer. Phys. Stat. Sol. A 148, 175–189. Zhang, W. X., and Wang, T. J. (2007). Effect of surface energy on the yield strength of nanoporous materials. Appl. Phys. Lett. 90, 063104-1–3. Zhao, M., Zhou, X. H., and Jiang, Q. (2001). Comparison of different models for melting point change of metallic nanocrystals. J. Mater. Res. 16, 3304–3307. Zhong, X. H., Feng, Y. Y., Knoll, W., and Han, M. Y. (2003). Alloyed ZnxCd1 – xS nanocrystals with highly narrow luminescence spectral width. J. Am. Chem. Soc. 125, 13559–13563. Zhou, L. G., and Huang, H. C. (2004). Are surfaces elastically softer or stiffer? Appl. Phys. Lett. 84, 1940–1942.

Connections between Elastic and Conductive Properties of Heterogeneous Materials Igor Sevostianov1 and Mark Kachanov2 1 Department of Mechanical Engineering, New Mexico State University, P.O. Box 30001,

Las Cruces, NM 88003, USA [email protected] 2 Department of Mechanical Engineering, Tufts University, Medford, MA 02155, USA

[email protected]

Abstract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

71

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72

2. Overview of Existing Approaches to Cross-property Connections . . . . . 2.1. Bristow’s Elasticity–Conductivity Connection for a Microcracked Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2. Cross-property Connections Involving the Bulk Modulus . . . . . . . 2.3. Cross-property Bounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4. Cross-property Connections for Piezoelectric Fiber-reinforced Composites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5. Empirical Observations on Cross-property Relations . . . . . . . . . . .

74 74 76 80 92 94

3. Quantitative Characterization of Microstructures: General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 3.1. Simplest Microstructural Parameters and their Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 3.2. Microstructural Parameters are Rooted in the Non-interaction Approximation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 3.3. Cases of Overall Isotropy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 3.4. Benefits of the Proper Microstructural Parameters . . . . . . . . . . . . . 101 4. Materials with Isolated Inhomogeneities: Microstructural Parameters for the Effective Elasticity and Effective Conductivity . . . . . . . . . . . . . . . 4.1. General Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2. Quantitative Characterization of Cracks . . . . . . . . . . . . . . . . . . . . . . 4.3. Example: Two-dimensional Elliptic Holes . . . . . . . . . . . . . . . . . . . . 4.4. Three-dimensional Inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . 4.5. Spheroidal Inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6. Microstructural Parameters for Conductive Properties: Comparison with Parameters for Elastic Properties . . . . . . . . . . . . . 4.7. Inhomogeneities of Irregular Shapes . . . . . . . . . . . . . . . . . . . . . . . . . ADVANCES IN APPLIED MECHANICS, VOL. 42 ISSN: 0065-2156 DOI: 10.1016/S0065-2156(08)00002-1

69

102 103 106 111 113 115 126 131


70

I. Sevostianov and M. Kachanov

5. Explicit Cross-property Connections for Anisotropic Two-phase Composites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1. Elasticity–Conductivity Connections: General Case . . . . . . . . . . . . 5.2. Cases of Overall Isotropy and Transverse Isotropy . . . . . . . . . . . . . 5.3. Materials with Cracks or Rigid Discs . . . . . . . . . . . . . . . . . . . . . . . . 5.4. On the Sensitivity of Elasticity–Conductivity Connection to Shapes of Inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5. Connection between the Degrees of Elastic/Conductive Anisotropies is Insensitive to Inhomogeneity Shapes . . . . . . . . . . . 5.6. On the Effect of Interactions and Nonspheroidal Inhomogeneity Shapes on the Cross-property Connections . . . . . . . . . . . . . . . . . . . . 5.7. On the General Elasticity–Conductivity Constraints . . . . . . . . . . . . 5.8. Connection between the Electric and the Thermal Conductivities . 5.9. Physical Properties that May Not Be Interrelated by Quantitative Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Cross-property Connections for Anisotropic Inhomogeneities . . . . . . . . 6.1. Cross-property Connections for Materials with Parallel Anisotropic Inhomogeneities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2. Moderate Orientation Scatter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3. Two or Three Families of Approximately Parallel Inhomogeneities 6.4. Nonlinear Connections for Parallel Isotropic Inhomogeneities of Unknown Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5. Fiber-reinforced Composites with Transversely Isotropic Piezoelectric Constituents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Applications of Cross-property Connections to Specific Materials Science Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1. Closed-cell Aluminum Foams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2. Microcracked Metal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3. Short Fiber-reinforced Thermoplastics . . . . . . . . . . . . . . . . . . . . . . . 7.4. Short Fiber-reinforced Plastics: Changes in Properties Due to Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5. Plasma-sprayed Ceramic Coatings . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6. Piezoelectric Fiber-reinforced Composites . . . . . . . . . . . . . . . . . . . . 8. Contact of Rough Surfaces: The Elasticity–Conductivity Connection . . 8.1. Hertzian Contact of the Circular Shape . . . . . . . . . . . . . . . . . . . . . . . 8.2. General Hertzian Contact of the Elliptic Shape . . . . . . . . . . . . . . . . 8.3. Hertzian Contacts versus “Welded” Areas . . . . . . . . . . . . . . . . . . . . 8.4. Multiple Contacts Between Two Rough Plates: Incremental Compliance, Conductivity, and Cross-property Connection . . . . . .

133 135 141 143 145 146 148 149 152 153 155 156 160 161 164 168 182 183 191 192 195 200 207 210 211 211 214 220

9. Plastic Yield Surfaces of Anisotropic Porous Materials in Terms of Effective Electric Conductivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 9.1. Approximate Constancy of Macroscopic Strain at Yield . . . . . . . . . 227

Connections between Elastic and Conductive Properties

71

9.2. Plastic Yield in Terms of Pore Space Characteristics . . . . . . . . . . . . 229 9.3. Plastic Yield in Terms of Effective Conductivities . . . . . . . . . . . . . . 230 9.4. Cases of Overall Isotropy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 10. Conclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 Appendix A. On Approximate Character of Elastic and Conductive Anisotropies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Appendix B. Tensor Basis for Transversely Isotropic Fourth-rank Tensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Appendix C. Series of Associated Elliptic Functions and Relevant Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246

Abstract We discuss cross-property connections that interrelate effective linear elastic and conductive properties of heterogeneous materials. More precisely, they relate changes in the properties, as compared to the ones of the bulk material, caused by various inhomogeneities (cracks, pores, inclusions). They may also be developed for microstructures formed by multiple contacts, such as rough surfaces pressed against each other. Such connections are especially useful if one property (say, electrical conductivity) is easier to measure than the other (anisotropic elastic constants). For the properties governed by mathematically similar laws (for example, electrical and thermal conductivities), the connections are straightforward. However, for the elasticity–conductivity connections – the main focus of the present work – their very existence is nontrivial: not only the governing equations are different but even the ranks of tensors characterizing the properties are different (fourth-rank tensor of elastic constants versus second-rank conductivity tensor). We overview various approaches to the problem and then advance the approach rooted in similarity of the microstructural parameters that control the given pair of properties. This similarity leads to connections that, albeit approximate, have explicit closed form. They have been experimentally verified on several heterogeneous materials (metal foams, short fiber reinforced composites, metals with fatigue microcracks, sprayed coatings). Moreover, for properties controlled by entirely essentially different parameters (such as permeability or fracture of a microcracked material and its elasticity), the correlations may hold only qualitatively, at best.

72


1. Introduction Cross-property connections for heterogeneous materials belong to the fundamental problems of engineering science and physics. They relate changes in different physical properties caused by various inhomogeneities (cracks, pores, inclusions) or, more generally, by the presence of certain microstructure. Their practical usefulness lies in the fact that one physical property (say, electrical conductivity) may be easier to measure than the other (say, anisotropic elastic constants). This allows one to bypass difficulties of expressing the elastic properties in terms of relevant microstructural information (that, in addition, may not be available). Such connections are also helpful in the design of microstructures for the combined conductive/mechanical performance. An example is given by thermal barrier coatings, where demands are made on both thermal conductivity and elastic stiffness. Aside from materials that can be described as continuous matrices containing inhomogeneities – the main focus of the present work – cross-property connections can also be developed for multiple contacts between rough surfaces pressed against each other. They can also be used to relate the yield condition of porous metals to the effective conductivity. Cross-property connections have been discussed in literature for about half a century. Some of them had a character of qualitative observations. For instance, geophysicists noticed that cracks in rocks increase both the elastic compliance and the fluid permeability. In fracture mechanics, attempts have been made to relate lifetime predictions to the loss of elastic stiffness of a material. Some of these connections cannot be upgraded from qualitative statements to quantitative relations that have some generality and are free from fitting parameters, for the reason that the considered pairs of properties may be controlled by entirely different microstructural factors. For example, fracture is quite sensitive to appearance of local clusters of defects, whereas the sensitivity of the effective elastic properties to clustering is, generally, low. The main focus of the present work is the elasticity–conductivity connection. Its very existence is not obvious: besides being governed by different differential equations, they are characterized by tensors of different ranks. Quantitative theoretical results on cross-property connections started to appear in 1960s. In the classical work of Bristow (1960), explicit elasticity–conductivity connection for a microcracked material was derived, in the isotropic case of random crack orientations and low crack density. Levin (1967) interrelated the effective bulk modulus and the effective thermal expansion coefficient of a general two-phase isotropic composite. Rosen and Hashin (1970) extended this result to anisotropic composite. Prager (1969) constructed Hashin–Shtrikman-based bounds for the


73

effective magnetic permeability (or electric conductivity) in terms of the effective thermal conductivity of a two-phase isotropic material. Later works can be generally classified into the following groups: A. Qualitative observations that cannot be upgraded to solid theoretical results (free of fitting parameters). B. Empirical relations that fit a particular set of data. C. Universal bounds connecting the two considered properties. D. Explicit cross-property connections for materials with isolated inhomogeneities and for rough surfaces pressed against each other. Works belonging to groups A, B, and C are discussed in Section 2. The present work focuses on the explicit connections D developed by the present authors. They are discussed in Sections 5 and 6, and their applications to materials science problems in Section 7. The connections are derived in the non-interaction approximation. However, this assumption is much less restrictive than may be expected, for the following reasons: • In many cases, predictions of the non-interaction approximation for each of the two properties remain accurate at substantial concentrations of inhomogeneities. For example, 3D analytical results of Sevostianov et al. (2006b) for a matrix with periodic distributions of anisotropic fibers show that for all the effective constants, both elastic and conductive, the non-interaction approximation produces errors less than 10% up to 30% volume fraction of fibers. At higher volume fractions, the results for C1313 (x3 -axis is parallel to the fibers) start losing accuracy, whereas for other effective constants, the non-interaction approximation remains accurate up to 40% volume fraction. We also refer to 3D computational study of the effective elastic properties of solids with multiple cracks (Grechka and Kachanov, 2006) that indicate accuracy of the noninteraction approximation up to crack densities of at least 0.14 (at which the local interaction effects are quite strong, as shown in this study). The underlying reason is that the competing interaction effects, of stress shielding and stress amplification, largely cancel each other. • In cases the interactions do affect the effective properties, it appears that their effect on both effective properties – elasticity and conductivity – is largely similar so that the connection between the two is not affected much. This hypothesis was first suggested by Bristow (1960) who concluded, on the basis of experimental data for microcracked metals, that cross-property connection for a microcracked material derived by him under the non-interaction assumption remains accurate at substantial crack densities. It is further confirmed by experimental data on metal foams (Sevostianov et al., 2006a), plasma-sprayed

74

I. Sevostianov and M. Kachanov coatings (Sevostianov et al., 2004), and, in particular, by rather unique experimental data of Choy et al. (1992) on the entire set of orthotropic elastic and conductive constants of composites reinforced with either glass or carbon fibers with volume fraction up to 34% (see Section 7). A related analytical result on fiber-reinforced composites is that the volume fraction of fibers at which the non-interaction approximation remains accurate increases from 30% to at least 40% if this approximation is applied to the cross-property connection rather than to each of the properties separately (Sevostianov et al., 2006b). Moreover, the accuracy range of the non-interaction approximation extends to almost fully dense packing for the connections involving all the elastic constants except C1313 .

The connections D are based on similarity of microstructural parameters that control the given pair of properties. They require, therefore, a careful examination of the parameters that are appropriate for a given physical property. This key issue is discussed in Sections 3 and 4. We note that, for the properties that are controlled by essentially different parameters, the correlations may be only qualitative, at best, as illustrated on two pairs of physical properties – fracture–elasticity and permeability–elasticity – in Section 5.9. 2. Overview of Existing Approaches to Cross-property Connections We overview the history of cross-property connections, with an emphasis on the elasticity – conductivity ones. The first quantitative result of this kind was given, to the best of our knowledge, by Bristow (1960) for solids with microcracks. It was followed by several results on cross-property connections involving the bulk modulus. A different approach to cross-property connections is represented by cross-property bounds, where substantial work involving advanced mathematical methods has been done in the last 20 years. For fiber-reinforced piezoelectric composites, yet another approach has been developed that extends the discussion of Hill (1964) on the number of independent effective elastic constants to materials of this type. We also mention several empirical cross-property connections of data-fitting nature suggested for several specific materials and conditions.

2.1. Bristow’s Elasticity–Conductivity Connection for a Microcracked Material This work (Bristow, 1960) explicitly relates changes in the effective conductivity and in the effective elastic moduli due to randomly oriented microcracks. Although his derivation implicitly assumes low crack density (interactions were


75

ignored), experimental data indicate that the derived connections remain relatively accurate at higher-than-expected crack densities. Based on results of Sack (1946) and Segedin (1951) for a single penny-shaped crack, Bristow (1960) derived expressions for changes in effective elastic constants due to multiple randomly oriented penny-shaped cracks as follows: E0 − E 16 1 − ν02 (10 − 3ν0 ) = ρ, E 45 2 − ν0 K0 − K 16 1 − ν02 = ρ, K 9 1 − 2ν0

(2.1)

G0 − G 32 (1 − ν0 ) (5 − ν0 ) ρ, = G 45 2 − ν0

where ρ = (1/V ) ai3 is the scalar crack density parameter ( ai is ith crack radius and V is the representative volume). E, K, and G denote the Young’s, bulk, and shear moduli; ν is Poisson’s ratio. Hereafter, superscript “0” indicates properties of the bulk material. Remark In the original equations of Bristow, multiplier 2 − ν0 in denominator of the expression for (G0 − G) /G is missing. Bristow also derived the decrease of electrical conductivity k assuming that cracks are nonconductive: 8 k0 − k = ρ. (2.2) k 9 Observing that changes in both the elastic and the conductive properties are expressed in terms of the same crack density parameter and eliminating it, Bristow (1960) derived explicit elasticity–conductivity connections 2 1 − ν02 (10 − 3ν0 ) k0 − k E0 − E = , E 5 (2 − ν0 ) k 2 1 − ν02 k0 − k K0 − K = , (2.3) K 1 − 2ν0 k 4 (1 − ν0 ) (5 − ν0 ) k0 − k G0 − G = . G 5 (2 − ν0 ) k Comparing these results with experimental data on microcracked metals, he observed that the agreement remained satisfactory when changes in the effective properties due to cracks were substantial, implying non-small crack densities. Based on this observation, he formulated the hypothesis that the connections remain accurate beyond the non-interaction approximation, because crack

76


interactions affect the elastic and the conductive properties in a similar manner (so that the connection between the two is not affected). This hypothesis is discussed further in Section 5.6.

2.2. Cross-property Connections Involving the Bulk Modulus A special class of cross-property connections that involve the bulk modulus has been developed starting from 1960s. Some of them were discussed in review of Hashin (1983). Here, we focus on three results of this kind that relate the bulk modulus to • the thermal expansion coefficient (Levin, 1967; Rosen and Hashin, 1970), • the specific heat (Rosen and Hashin, 1970), • the thermal conductivity of composites containing radially inhomogeneous inclusions (Lutz and Zimmerman, 2005). 2.2.1. Levin’s Formula and its Extension to Anisotropic Materials Levin (1967) established the connection between the effective bulk modulus K and the effective thermal expansion coefficient α of a two-phase (phases 0 and 1) isotropic composite with isotropic constituents: α − α = (α0 − α1 )

1 1 − K0 K1

−1

1 1 − , K K

(2.4)

where angle brackets denote volume averaging. It has been generalized to anisotropic two-phase composites by Rosen and Hashin (1970) as follows:

(0) (1) (0) (1) −1 Sklrs − Sklrs Srsij − Srsij , αij − αij = αkl − αkl

(2.5)

where Sijkl are elastic compliances and αij are thermal expansion coefficients. We now outline the arguments leading to these connections following a much shorter reasoning privately communicated by Levin (2006). We consider a twophase composite of arbitrary microstructure and start with constitutive equations of thermoelasticity: εij (x) = Sijkl (x)σkl (x) + αij (x)T,

(2.6)

s(x) = αij (x)σij (x) + χ(x)T,

(2.7)

where χ and s are the specific heat and the entropy. Temperature T is assumed to be uniform within the representative volume. We represent the fields as sums of


77

their volume averages (denoted by angle brackets) and fluctuations (denoted by prime): S(x) = S + S (x) ,

α(x) = α + α (x) ,

σ(x) = σ + σ (x)

so that averaging over the representative volume yields

(x) σ (x) + α T, εij = Sijkl σkl + Sijkl ij kl s = αij σij + αij (x) σij (x) + χ T.

(2.8)

(2.9)

Due to linearity of the problem, the fluctuations are linear functions of the average stresses and temperature: σij (x) = ijkl (x) σ kl + λij (x)T,

(2.10)

where (x) and λ(x) are certain tensor coefficients. Substitution into (2.9) yields

λ T + α T, σ + S εij = Sijkl σkl + Sijkl klmn mn ij ijkl kl (2.11)

s = αij σij + αij ijkl σkl + αij λij T + χT. Therefore, for the effective compliances Sijkl , the effective thermal expansion coefficients αij , and the effective specific heat χ, defined by

εij = Sijkl σkl + αij T,

s = αij σij + χT,

(2.12)

we have:

Sijkl = Sijkl + Sijmn mnkl ,

αij − αij = Sijkl λkl = αmn mnij ,

χ = χ + αij λij .

(2.13)

For a two-phase composite, averages over phases are

0 1 mnkl 0 , = p1 Sijmn − Sijmn 0

1 0 mnkl 1 , Sijmn mnkl = p0 Sijmn − Sijmn Sijmn mnkl

1

(2.14)

78


where p0 , p1 are volume fractions of the phases (p0 + p1 = 1) Similar relations can be written for Sijmn λmn , αmn mnij , and αmn λmn . Then, the following identities hold

mnkl = p0 Sijmn mnkl + p1 Sijmn mnkl Sijmn 0 1 0 1 = p0 p1 Sijmn − Sijmn mnkl 0 − mnkl 1 ,

λmn = p0 Sijmn λmn + p1 Sijmn λmn Sijmn 0 1 0 1 (2.15) = p0 p1 Sijmn − Sijmn λmn 0 − λmn 1 ,

αmn mnij = p0 αmn mnij 0 + p1 αmn mnij 1

= p0 p1 α0mn − α1mn mnij 0 − mnij 1 ,

αmn λmn = p0 αmn λmn 0 + p1 αmn λmn 1 = p0 p1 α0mn − α1mn λmn 0 − λmn 1 . Substitution of the first and the third of these expressions into Eq. (2.13) yields Eq. (2.5) and, in the case of isotropy, Eq. (2.4).

2.2.2. Rosen–Hashin’s formula For the effective specific heat, substitution of the second and the fourth equations of (2.15) into (2.13) gives (0) (1) (0) (1) −1 χ − χ = αkl − αkl Sklrs − Sklrs αij − αij .

(2.16)

In the case of the isotropic composite with isotropic constituents, it takes the form χ − χ = 9 (α0 − α1 )

1 1 − K0 K1

−1

(α − α).

(2.17)

Remark Both Levin’s and Rosen–Hashin’s cross-property connections (2.4), (2.5) and (2.16), (2.17) are obtained without any assumptions on microgeometries. In particular, the inhomogeneities do not have to be isolated and their volume fractions can be arbitrary. Results of Levin (1967) and Rosen and Hashin (1970) were further extended to two-phase electroelastic composites by Dunn (1993). He related the effective thermal expansion and pyroelectric coefficients to the effective elastic, piezoelectric, and dielectric constants.


79

2.2.3. Lutz–Zimmerman’s result Lutz and Zimmerman (2005) considered an isotropic matrix containing spherical inclusions (marked by subscript “1”) surrounded by an inhomogeneous interphase layer with an arbitrary law of the radial variation in properties. At the outer boundary of the layer, its properties coincide with the ones of the matrix (marked by subscript “0”). The connection discussed below holds exactly if Poisson’s ratio of the interphase layers is zero, otherwise it has approximate character. The connection is based on similarity between governing equations in the conductivity and elasticity problems. In the conductivity problem, the equation has the form 2 d2 f 2 df df − 2 f + k (r) = 0, (2.18) k(r) + r dr dr dr 2 r where k(r) is the thermal conductivity of the inclusion and f(r) is a function characterizing the radial variation of temperature. In the elasticity problem, the radial displacement u(r) obeys the equation:

du d2 u 2 du 2 u [λ(r) + 2μ(r)] + − 2 u + λ (r) + 2μ (r) + 2λ (r) = 0, r dr dr r dr 2 r (2.19) where λ(r) and μ(r) are Lamé coefficients. It is seen that, in the case λ = 0 (Poisson’s ratio is zero), Eqs. (2.18) and (2.19) are identical. For a material with multiple inhomogeneities (having identical radial variations of properties), this leads to a direct correspondence between the effective bulk modulus and the effective conductivity: K 1 − 2[(K0 − K1 )/(K1 + 2K0 )]c = , K0 1 + [(K0 − K1 )/(K1 + 2K0 )]c

(2.20)

where volume fraction c is expressed in terms of the effective conductivity by c=

k1 + 2k0 k − k0 . k1 − k0 k + 2k0

(2.21)

The connection (2.20, 2.21) was not explicitly given by Lutz and Zimmerman (2005), but immediately follows from their results. This connection is exact to the first order in volume fraction c. We also observe that it represents relation between Hashin–Shtrikman’s upper bounds for the two properties.

80


2.3. Cross-property Bounds Cross-property bounds interrelate, in the form of inequalities, the effective elastic and the effective conductive properties. They are universal, in the sense that they hold for all microgeometries. So far, bounds of this kind have been limited to the isotropic overall properties of two-phase composites, with two trivial exceptions: • elasticity–conductivity connection in the isotropy plane of a transversely isotropic material; • bulk modulus–conductivity connection that holds for the isotropic material can, obviously, be applied to a material with cubic symmetry (since, for both the bulk modulus and the conductivity, the cubic symmetry is indistinguishable from isotropy). Several bounds discussed here have been obtained by different mathematical means. We attempt to present the results and the underlying ideas in a readerfriendly form, simplifying arguments of the original works to the extent possible and refer the reader to the original articles for further details.

2.3.1. Milton’s Inequality Milton’s (1984) inequality is based on the minimum potential energy principle that, for macroscopically isotropic composite with isotropic phases, has the form (Beran, 1968):

2

Ktr ε2 + 2Ge : e ≤ K tr εˆ + 2 Gê : eˆ ,

(2.22)

where angle brackets denote volume averages, e = ε − (1/3)(tr ε)I is the strain deviator, and I the second-rank unit tensor. Symbol εˆ stands for the “trial” strain field that is kinematically compatible, but the associated stress field is not necessarily divergence-free (and vice versa, the trial stress field is divergence-free, but the associated strain field is not necessarily compatible). It is subject to the restriction ˆε = ε.

Taking εˆ such that εˆ = I/3 brings inequality (2.22) to the form

2 K ≤ K tr εˆ + 2G eˆ : eˆ

2 2 2 = λ tr εˆ + 2G εˆ : εˆ − 4G 9 tr εˆ ≤ λ tr εˆ + 2G εˆ : εˆ , (2.23)


81

where λ = (3K − 2G)/3 is Lamé’s constant. This leads to the following inequality that relates the effective bulk modulus K and the effective conductivity k: k K ≤ , K1 k1

(2.24)

where subscript 1 refers to phase 1 of the composite (the two phases are assigned numbers 0 and 1 in such a way that K0 /K1 ≤ k0 /k1 ). Restricting attention to materials with nonnegative effective Poisson’s ratios, v ≥ 0, this inequality implies the following bound for the effective shear modulus: G 3k ≤ , K1 2k1

(2.25)

as noted by Torquato (1992). We now outline the proof of the above inequalities, following Milton (1984). His essential idea, which is rooted in work of Tartar (1979), is to link the trial displacement field uˆ to the gradient E of the exact electric potential, by choosing uˆ = T such that ˆε = T = I/3 and relating T to E in such a way that the latter obeys the equation E · E = a2 ∇T : ∇T,

(2.26)

where dimensional constant a is introduced to make the physical dimensions of the left- and right-hand parts compatible. With the usual assumption that the composite is ergodic (the effective properties can be formulated in terms of volume, rather than ensemble, averages), the effective conductivity has the following energy representation: 1 1 kE·E = k E · E 2 2

(2.27)

k = 3k∇T : ∇T .

(2.28)

and

At the same time, the trial strain can be written in terms of T: εˆ = (1/2) ∇T + (∇T)T .

(2.29)

We assume that Poisson’s ratios of both constituents are nonnegative (i.e., Lamé constant λ is nonnegative) and take into account that

2

tr εˆ

≤ 3ˆε : εˆ = 3∇T : ∇T.

(2.30)

82


Then, inequality (2.23) yields the upper bound for the effective bulk modulus: K ≤ 3 K∇T : ∇T .

(2.31)

With the aid of the characteristic function V (i) (x) that is equal to 1 if x is in ith phase and 0 otherwise, we rewrite (2.28) and (2.31) as

k k0 (0) = 3 V (1) (x) ∇T : ∇T + 3 V (x) ∇T : ∇T , k1 k1

(2.32)

K0 (0) K V (x) ∇T : ∇T , ≤ 3 V (1) (x) ∇T : ∇T + 3 K1 K1

(2.33)

and the bound (2.24) follows. Milton (1984) made the interesting observation that, according to inequality (2.24), a composite with K1 = K0 , k1 = k0 cannot be incompressible and have finite conductivity, but a composite that is compressible and superconducting may exist. 2.3.2. Berryman–Milton’s Bounds Berryman and Milton (1988) constructed elasticity–conductivity bounds for a two-phase isotropic composite that are significantly tighter than the “elementary” bounds discussed above. They utilize bounds derived separately for the effective conductivity (Beran, 1965) and for the effective elastic constants (Beran and Molyneux, 1966; McCoy, 1970). These two sets of bounds take into account not only volume fractions of phases but the information on microgeometry provided by three-point correlation functions. An important observation is that this information is utilized by the two bounds in a similar way, reflecting similarities between effects of microgeometry on the two properties. This leads to cross-property bounds that are independent of microgeometry. Remark This similarity echoes the observation made by Bristow (1960) in a narrower context of cracks, that crack interactions – that are very sensitive to the geometry of crack arrangements – affect the conductivity and the elastic constants in a similar way so that the connection between the two is not affected. The three-point correlation function provides an approximate characterization of microgeometry: it gives the probability that material belonging to a given phase of a composite is located at three given points. For phase 1, this function is defined by

s3 (r1 , r2 , r3 ) = V (1) (x + r1 ) V (1) (x + r2 ) V (1) (x + r3 ) , (2.34)


83

where V (1) (x) is the characteristic function of the first phase. Based on the correlation function, the following two dimensionless microstructural parameters are introduced: 9 lim lim ζ= 2c0 c1 →0 →∞

dr

+1 ds −1

150 5ζ1 + lim lim η= 21 7c0 c1 →0 →∞

dr

S3 (r, s, μ) P2 (μ)dμ, rs +1 ds

−1

S3 (r, s, μ) P4 (μ)dμ, rs

(2.35)

where P2 (μ) = (3μ2 − 1)/2 and p4 (μ) = (35μ4 − 30μ2 + 3)/8 are Legendre polynomials of orders 2 and 4 and S3 r12 , r13 , μ12,13 = s3 (r1 , r2 , r3 ),

(2.36)

(r2 − r1 ) · (r3 − r1 ) rij = rj − ri , μ12,13 = . r12 r13

(2.37)

with

This form of the correlation function emphasizes the statistical homogeneity of the microgeometry (invariance with respect to translations in any direction). Parameters ζ and η obey the following inequalities (Milton and Phan-Thien, 1982): 5ζ/21 ≤ η ≤ (16 + 5ζ)/21.

(2.38)

The key observation of Berryman and Milton (1988) is that bounds for different physical properties – magnetic permeability, electrical or thermal conductivity, and elastic constants – can be expressed in terms of the same two parameters, ζ and η. Focusing attention on the elasticity–conductivity pair and excluding the two parameters leads to bounds on the effective bulk and shear moduli in terms of the effective conductivity. The basic arguments are as follows. In addition to the usual volume average = 0 + ( 1 − 0 )c1 of a certain physical property , Berryman and Milton (1988) introduced averages that involve microstructural parameters (2.35): ζ = 0 + ( 1 − 0 ) ζ, η = 0 + ( 1 − 0 )η.

(2.39)

84


In terms of these averages, bounds of Beran (1965) for the effective conductivity and bounds of Beran and Molyneux (1966) and McCoy (1970) for the elastic moduli take the form ≤ k ≤ A1 kζ , (2.40a) A1 1/k−1 ζ A2 1/G−1 ≤ K ≤ A2 Gζ , (2.40b) ζ (2.40c) A3 (/6) ≤ G ≤ A3 1 6 , where functions A1−3 (x) are defined as follows −1 1 A1 (x) = − 2x, k + 2x −1 1 − 4x/3, A2 (x) = K + 4x/3 −1 1 − x, A3 (x) = G+x

(2.41)

and the following notations are used =

10 G2 Kζ + 5 G 2K + 3G Gζ + 3K + G2 Gη K + 2G2

,

(2.42) 10 K2 1/Kζ + 5 G 2K + 3G 1/Gζ + 3K + G2 1/Gη = . 9K + 8G2 Note that bounds for the conductivity and for the bulk modulus contain parameter ζ only, whereas bounds for the shear modulus contain both microstructural parameters ζ and η. Substituting ζ from inequality (2.40a) for conductivity, as well as (2.38), into inequalities (2.40b,c) for the bulk and shear moduli would lead to the elasticity–conductivity cross-property bounds. For a general composite material, this procedure is quite cumbersome and, to our knowledge, has not been implemented in explicit form. For a nonconducting porous material filled with conductive fluid, results can be given in the explicit form. In this case, Beran’s bounds degenerate into one inequality: 1 c0 1 c0 k k1 /k ≥ 1 + 1 + , or ζ ≥ , (2.43) 2ζ c1 2 c1 k1 − k


85

and Beran–Molyneux’ bounds are ζ ≤1−

3c1 K/4G0 , c0 − K/K0

(2.44)

η≥1−

6R(K0 + 2G0 )2 − 5G0 (1 − ζ)(4K0 + 3G0 ) , (3K0 + G0 )2

(2.45)

where R = (c1 G/G0 )/(c0 − G/G0 ). This leads to cross-property bounds interrelating the effective bulk modulus and the effective conductivity: 3c1 K/4G0 1 c0 k ≤ζ ≤1− . 2 c1 k1 − k c0 − K/K0

(2.46)

To obtain bounds for the effective shear modulus, we introduce dimensionless combinations of elastic constants of phase “0” A0 =

6(K0 + 2G0 )2 5G0 (4K0 + 3G0 ) , B0 = . 2 (3K0 + G0 ) (3K0 + G0 )2

(2.47)

Using (2.38) and rewriting (2.45) in the form 5 c1 G/G0 ζ ≤ η ≤ 1 + B0 − B0 ζ − A0 21 c0 − G/G0 implies the following cross-property bound 21A0 6c1 G/G0 1 c0 k 1 + B0 . − ≤ ζ ≤ 21 2 c1 k1 − k 5 − 21B0 5 − 21B0 c0 − G/G0

(2.48)

(2.49)

Remark 1. Bounds (2.46) and (2.49) involve volume fractions c1 and c0 ; therefore, they become trivial for inhomogeneities of vanishing volume, in particular for cracks. Remark 2. Berryman and Milton (1988) noted that, since inequalities (2.46), (2.51) for parameters ζ and η are independent of the properties of phase “1,” they can be specialized, for example, for a porous material and then used for generating bounds for material of the same microgeometry but with pores replaced by a constituent with different properties. Similar ideas were developed by Bergman (1978) and Kantor and Bergman (1984). 2.3.3. Gibiansky–Torquato’s Translation-based Cross-property Bounds These bounds are based on the translation method outlined below. Its application to cross-property bounds was pioneered by Cherkaev and Gibiansky (1992) in the context of conductive-magnetic bounds for two-dimensional composites; for a

86


review of the translation method, see the book of Cherkaev (2000). Gibiansky and Torquato (1993, 1995, 1996a) applied this method to the elasticity–conductivity bounds for 2D isotropic composites and to the bulk modulus–conductivity bounds for 3D composites. They specified these bounds for several microstructures: microcracked material (Gibiansky and Torquato, 1996b), dry and fluid-saturated porous rocks (Gibiansky and Torquato, 1998a), porous or cracked nonlinear conductors assuming the elastic properties to be linear (Gibiansky and Torquato, 1998b) and 2D cellular solids (Torquato et al., 1998). They also applied these results to a design of porous materials for a combined dielectric-stiffness performance (Torquato et al., 2005). The methodology utilizes two concepts – of the translation tensor and of the Y-tensor. The translation tensor T and its application to bounding the effective properties was introduced by Tartar (1979), Murat and Tartar (1985), Lurie and Cherkaev (1982, 1984), and Milton (1990). We consider some physical property of a heterogeneous material, say elastic compliance tensor, its local value S(x), and its effective value S. Translation tensor T is a special tensor that possesses the following property: if S(x) is shifted, at each point x, by a multiple of T: S (x) = S (x) − κT,

(2.50)

then S of this new medium is translated by κT as well: S = S − κT.

(2.51)

The multiplier κ chosen in such a way that S is semi-positive definite. The translation tensor can be introduced for other physical properties as well, including coupled properties (in which case the translation tensor has to be replaced by several ones arranged in a matrix). For a discussion of the method in detail, see books of Cherkaev (2000) and Milton (2002). The Y-tensor interrelates field fluctuations averaged over a given phase. It was introduced by Milton (1997) based, to some extent, on earlier works of Berryman (1980a,b, 1982). For elastic fields in phase 1 of a two-phase composite, the fourthrank Y-tensor is defined by

V (1) (x) (ε − ε) = −Y : V (1) (x) (σ − σ) . (2.52) Since characteristic functions are interrelated by V (1) (x) = 1 − V (0) (x), the Ytensor for phase 0 is the same:

V (0) (x) (ε − ε) = −Y : V (0) (x) (σ − σ) . (2.53)


87

For the conductivity problem, the second-rank Y-tensor can be introduced in a similar way. Construction of the Cross-property Bounds We now consider a 3D composite that consists of two isotropic phases and is isotropic, overall, and derive the conductivity–elasticity bounds following Gibiansky and Torquato (1996a). Their derivation requires specifying the sign of the product (k1 − k0 )(G1 − G0 ). We consider the case (k1 − k0 ) (G1 − G0 ) ≤ 0.

(2.54)

We write pointwise Hooke’s law in the following form σ (x) = [3K (x) 1 + 2G (x) 2 ] : ε (x),

(2.55)

where two tensors (1 )ijkl =

1 δij δkl , 3

(2 )ijkl =

1 1 δik δjl + δil δjk − δij δkl , 2 3

(2.56)

supplemented by (3 )ijkl =

1 δik δjl − δil δjk , 2

(2.57)

constitute an orthogonal basis for fourth-rank isotropic tensors (any such tensor can be expressed as their linear combination). For the conductive properties, the following procedure suggested by Milton (1984) is used. Three electric fields e(1) (x), e(2) (x) and e(2) (x) are applied to the composite. They form columns of 3 × 3 matrix-valued field E(x). The three resultant fields of currents j (1) (x), j(2) (x), and j(3) (x) form columns of 3 × 3 matrix-valued field J(x). The conductivity law then takes the form: J(x) = k(x)I 4 : E(x), (2.58) 4 = δ δ is the fourth-rank identity tensor. Now, the constitutive relation where Iijkl ik jl for the elastic and conductive properties can be written in the combined form: ε σ (0) (1) = V L0 + V L1 , (2.59) J E

where

3Ki 1 + 2Gi 2 Li = 0

0 , ki 1 + ki 2 + ki 3

i = 0, 1.

(2.60)

88


The combined effective elastic and conductive constants have a similar form: L=

3K1 + 2G2 0

0 k1 + k2 + k3

(2.61)

and the associated Y-tensors can be arranged in a matrix as follows Y=

3yK 1 + 2yG 2

0

0

yK 1 + yK 2 + yK 3

,

(2.62)

where the y-parameters, yK = −c0 K1 − c1 K0 −

c0 c1 (K0 − K1 )2 , K − c 0 K0 − c 1 K1

yG = −c0 G1 − c1 G0 −

c0 c1 (G0 − G1 )2 , G − c 0 G0 − c 1 G1

yk = −c0 k1 − c1 k1 −

(2.63)

c0 c1 (k0 − k1 )2 , k − c0 k0 − c1 k1

are y-transformations of the effective bulk and shear moduli and of the conductivity introduced by Berryman (1982). For the translation, Gibiansky and Torquato (1996a) use the following tensor −t1 (21 − 2 + 3 ) −t3 (21 − 2 + 3 ) T = . (2.64) −t3 (21 − 2 + 3 ) −t2 (21 − 2 + 3 ) The requirement that Li − T is semi-positive definite for both phases, that is, ⎛ ⎜ ⎝

(3Ki + 2t1 ) 1 + (2Gi − t1 ) 2 + t1 3 t3 (21 − 2 + 3 )

t3 (21 − 2 + 3 )

⎞

⎟ (ki + 2t2 ) 1 + (ki − t2 ) 2 + (ki + t2 ) 3 ⎠ ≥ 0 (2.65)

decouples, due to orthogonality of 1 , 2 , 3 , into three inequalities 2Gi − t1 3Ki + 2t1 2t3 −t3 ≥ 0, ≥ 0, 2t3 ki + 2t2 −t3 ki − t 2 t1 t3

t3 ki + t 2

≥ 0,

(2.66)


89

where index i = 0, 1 indicates the phase number. The necessary and sufficient condition for these inequalities to hold is that each of the six matrices is semipositive definite, so that the following two conditions have to be met: 0 ≤ t1 ≤ min (2G0 , 2G1 ) ,

(2.67)

and determinant of each matrix has to be nonnegative, that is, t1 , t2 , t3 must satisfy the inequality (3y1 /2 − t1 ) (y2 /2 − t2 ) − t33 ≥ 0

(2.68)

for each of the following six pairs of (y1 , y2 ): (k0 , K0 ), (k1 , K1 ), (−2k0 , −4G0 /3), (−2k1 , −4G1 /3), (2k0 , 0), (2k1 , 0). (2.69) It is possible now to construct bounds that interrelate the effective conductivity k and the effective bulk modulus K (but not the effective shear modulus!) in the plane of parameters (yk , yK ). These bounds are formed by the outermost of five curves: four segments of hyperbolae passing through the points indicated in brackets: Hyp [(−2k0 , −4G0 /3) , (−2k1 , −4G1 /3) , (k0 , K0 )] , Hyp [(−2k0 , −4G0 /3) , (−2k1 , −4G1 /3) , (k1 , K1 )] ,

(2.70)

Hyp [(−2k0 , −4G0 /3) , (−2k1 , −4G1 /3) , (2k0 , 0)] , Hyp [(−2k0 , −4G0 /3) , (−2k1 , −4G1 /3) , (2k1 , 0)] , and the straight line connecting points (−2k0 , −4G0 /3) and (−2k1 , −4G1 /3). It is further stated (Gibiansky and Torquato, 1996a) that bounds in the (k, K) plane are formed by two hyperbolae that pass through points (k0 , K0 ) and (k1 , K1 ) and touch the set given by the five mentioned lines More explicit bounds can be obtained in the case when the volume fractions ci of constituents are known. Then the outermost pair of following five hyperbolae gives the bounds: Hyp [(k0∗ , K0∗ ) , (k1∗ , K1∗ ) , (k0 , K0 )] , Hyp [(k0∗ , K0∗ ) , (k1∗ , K1∗ ) , (k1 , K1 )] , Hyp [(k0∗ , K0∗ ) , (k1∗ , K1∗ ) , (k0# , Kh )] , Hyp [(k0∗ , K0∗ ) , (k1∗ , K1∗ ) , (k1# , Kh )] , Hyp [(k0∗ , K0∗ ) , (k1∗ , K1∗ ) , (ka , Ka )] ,

(2.71)

90


where the following notations are used k0∗ = c0 k0 + c1 k1 −

c0 c1 (k0 − k1 )2 , c1 k0 + c0 k1 + 2k0

k1∗ = c0 k0 + c1 k1 − k1# = c0 k0 + c1 k1 −

c0 c1 (k0 − k1 )2 , c1 k0 + c0 k1 + 2k1

c0 c1 (k0 − k1 )2 , c1 k0 + c0 k1 − 2k0

k2# = c0 k0 + c1 k1 −

c0 c1 (k0 − k1 )2 , c1 k0 + c0 k1 − 2k1

ka = c0 k0 + c1 k1 , K0∗ = c0 K0 + c1 K1 −

c0 c1 (K0 − K1 )2 , c1 K0 + c0 K1 + 4G0 /3

K1∗ = c0 K0 + c1 K1 −

c0 c1 (K0 − K1 )2 , c1 K0 + c0 K1 + 4G1 /3

Ka = c0 K0 + c1 K1 , Kh = (c0 /K0 + c1 /K1 )−1 . Note that Gibiansky–Torquato’s bounds are realizable and therefore cannot be improved without additional information on microstructure. Fig. 2.1 shows that these bounds are substantially narrower than Berryman–Milton’s bounds. In contrast with Berryman–Milton’s bounds that are formulated in volume fractions and, therefore, become trivial for a cracked material, Gibiansky–Torquato’s bounds produce an inequality in this case, which, assuming v0 ≥ 0, has the following form (Gibiansky and Torquato, 1996b):

1 1 − K K0

≥

3k0 1 − ν0 2G0 1 + ν0

1 1 . − k k0

(2.72)

This inequality requires, however, an additional assumption: k0 1 − ν0 6k1 ≤ G0 1 + ν 0 3K1 + 4G1

(2.73)

that is somewhat unclear since k1 , K1 , and G1 are zeros for cracks. It is interesting to compare inequality (2.72) for cracks with the explicit elasticity–conductivity connection (2.3) of Bristow (1960). Fig. 2.2 compares Gibiansky–Torquato’s bound (2.72), Milton’s inequality (2.24), and Bristow’s cross-property connection (2.3) for the effective bulk modulus of a microcracked material.


91

20.0 15.0

1

Milton

2

Berryman–Milton

3

Gibiansky–Torquato

K /K1

1 10.0

K2 / K1 5 20

2

k2 / k1 5 20

5.0

n0 5 n1 5 0.3

3 0.0 0.0

5.0

10.0

15.0

20.0

k/k1 Fig. 2.1 Comparison of different cross-property bounds. The inner region corresponds to Berryman–Milton bounds for fixed volume fraction c1 = 0.2; its shaded part to Gibiansky–Torquato bounds. 1.00 n0 5 0.3

K /K1

0.75

1

Bristow

2

Milton

3

Gibiansky–Torquato

0.50 3

2 0.25

1

0.00 0.00

0.25

0.50

0.75

1.00

k/k1 Fig. 2.2 Comparison of the Bristow cross-property connection (2.3) for bulk modulus of a microcracked material (randomly oriented cracks) with Milton inequality (2.24) and Gibiansky–Torquato bound (2.72).

2.3.4. Cross-property Bounds Implied by Hashin–Shtrikman’s Bounds Hashin–Shtrikman’s (HS) bounds formulated separately for the effective elastic moduli (Hashin and Shtrikman, 1963), and the effective conductivity (Hashin and Shtrikman, 1962) can be used to produce cross-property bounds. Indeed, rewriting the HS bounds for conductivity as inequalities for volume fractions (assuming for certainty that k0 > k1 ) (k − k1 ) (2k1 + k0 ) 3k0 (k − k1 ) ≤ c0 ≤ ≤ 1, (2k0 + k) (k0 − k1 ) (2k1 + k) (k0 − k1 ) (k0 − k) (2k0 + k1 ) 3k1 (k0 − k) 0≤ ≤ c1 ≤ ≤1 (2k1 + k) (k0 − k1 ) (2k0 + k) (k0 − k1 )

0≤

(2.74)

92


and substituting them into similar inequalities for the elastic constants, we find cross-property bounds that relate the bulk and shear moduli to conductivity: K1 +

f(k) (K0 − K1 ) (3K1 + 4G1 ) ≤K (3K1 + 4G1 ) + 3 (K0 − K1 ) [1 − f(k)]

(2.75a) [1 − f(k)] (K1 − K0 ) (3K0 + 4G0 ) , ≤ K0 + (3K0 + 4G0 ) + 3 (K1 − K0 ) f(k) 5f(k)G1 (G0 − G1 ) (3K1 + 4G1 ) G1 + ≤G 5G1 (3K1 + 4G1 ) + 6 (G0 − G1 ) (K1 + 2G1 ) [1 − f(k)] (2.75b) 5 [1 − f(k)] G0 (G1 − G0 ) (3K0 + 4G0 ) , ≤ G0 + 5G0 (3K0 + 4G0 ) + 6 (G1 − G0 ) (K0 + 2G0 ) f(k) where f(k) =

3k0 (k − k1 ) (2k0 + k) (k0 − k1 )

(2.76)

and where it is assumed that K0 > K1 , G0 > G1 . However, cross-property bounds obtained this way are quite wide – they are much wider than the HS bounds themselves. This is particularly clear in the case of a porous material, when thus obtained bounds reduce to trivial statements. Note that, in the 2D case, cross-property bounds of this kind were given by Zhao et al. (2004). Remark In terms of the numerical implementation, the HS-based cross-property bounds are probably the simplest, but they are the least tight (becoming useless in the case of a porous material). The Gibiansky–Torquato’s translation-based bounds are the most tight ones, but they are, probably, the hardest to implement. The Berryman–Milton’s bounds are intermediate from the point of view of tightness and difficulties of the numerical implementation.

2.4. Cross-property Connections for Piezoelectric Fiber-reinforced Composites Cross-property connections for piezoelectric composites reinforced by infinite fibers were derived by Benveniste and Dvorak (1992) and Schulgasser (1992). The linear constitutive equations for a transversely isotropic piezoelectric material have the form: σ11 = C11 ε11 + C12 ε22 + C13 ε33 − e31 E3 , σ22 = C12 ε11 + C11 ε22 + C13 ε33 − e31 E3 ,


93

σ33 = C13 ε11 + C13 ε22 + C33 ε33 − e33 E3 , σ12 = C66 ε12 , σ13 = C44 ε13 − e15 E1 ,

(2.77)

σ23 = C44 ε23 − e15 E2 , D1 = e15 ε13 + ζ11 E1 , D2 = e15 ε23 + ζ11 E2 , D3 = e31 ε11 + e31 ε22 + e33 ε33 + ζ33 E3 , where εij and σij are strains and stresses, Di are the electric displacements (components of the electric induction vector), and Ei are components of the electric field vector. The equations contain five elastic stiffnesses Cij , three piezoelectric constants eij , and two dielectric permeabilities ηij . In the text to follow, the matrix and fiber constants will be denoted by superscripts “0” and “1,” correspondingly, the effective constants will be marked by an asterisk, and quantities marked by superscript “d” will stand for the differences between corresponding constants of d = C1 − C0 . the end of the matrix, for instance C11 11 11 Extending well-known Hill’s (1964) universal relations for a fiber-reinforced linear elastic composite d + Cd C11 12 d 2C13

=

∗ + C∗ − Cv − Cv ∗ − Cv C11 C13 11 12 13 12∗ = ∗ − Cv v C33 2 C13 − C13 33

(2.78)

to the piezoelectric one. Benveniste and Dvorak (1992) derived the following two groups of cross-property relations reducing the number of independent effective constants from ten to five: d + Cd C11 12 d 2C13 d + Cd C11 12

2ed31

=

=

∗ + C∗ − Cv − Cv ∗ − Cv C13 C11 e∗31 − ev31 11 12 13 12∗ = = , ∗ − Cv v C33 e∗33 − ev33 2 C13 − C13 33

(2.79)

∗ + C∗ − Cv − Cv v C11 e∗ − ev31 C∗ − C13 11 12 12∗ = − 31 = 13 ∗ ∗ − ζv , v v e33 − e33 ζ33 2 e31 − e31 33

(2.80)

v = where superscript v denotes the Voigt arithmetical average: for instance, C13 0 1 (1 − f ) C13 + fC13 . Benveniste and Dvorak (1992, pp. 1305–1306) also showed that the conditions of the theorem of Milgrom and Shtrikman (1989) are satisfied for uniaxial fiber-reinforced composites with transversely isotropic phases (orientation of fibers coincides with the symmetry axes of phases). This theorem yields the following

94


universal relation for transversely isotropic piezoelectric composites that involves constants C44 , e15 , and ζ11 ⎡ ∗ 2 ⎤ e15 e∗15 1 ∗ + ζ ⎢ ∗ 11 ∗ ∗ ⎥ C44 ⎥ ⎢ C44 C44 ⎥ ⎢ 2 ⎢ 1 e015 ⎥ e015 ⎥ ⎢ 0 (2.81) det ⎢ 0 ζ11 + ⎥ = 0. 0 0 ⎥ ⎢ C44 C44 C 44 ⎥ ⎢ 1 2 ⎥ ⎢ e e115 ⎦ ⎣ 1 1 ζ11 + 151 1 1 C44 C44 C44 This relation further reduces the number of independent effective piezoelectric constants to only four. Remark Schulgasser (1992) gave a connection between C44 , e15 , and ζ11 that is different from (2.81): ⎡ ∗ ⎤ ∗ C44 e∗15 ζ11 ⎢ ⎥ 0 0 ⎥ ⎢ 0 det ⎢C44 e15 ζ11 ⎥ = 0. ⎣ 1 ⎦ 1 C44 e115 ζ11 It is based on application of Milgrom and Shtrikman (1989) relation for magnetoelectric effect to the piezoelectric problem. Such an application is not fully justified, however, for the reason that, in the magnetoelectric case, the matrix is symmetric and positive definite, whereas, in the piezoelectric case, it is not.

2.5. Empirical Observations on Cross-property Relations Aside from theoretical developments, cross-property correlations of the datafitting nature have been suggested in literature for several materials. In the work of Zamora et al. (1993), thermal conductivity of approximately isotropic rock specimens (Fontainebleau sandstone, 99.8% quartz) at three different porosities (4.3%, 9.7%, and 16.2%) was related to wavespeeds VP = √ √ (K + 4μ) /3ρ and VS = μ/ρ (where ρ is material density). The three available data points were approximated by the following best-fit linear relations WS VP = αWS P k − βP ,

WS VS = αWS S k − βS

(water saturated rock),

where fitting parameters are chosen as follows 3 2 −1 αWS W−1 , βPWS = 1.96 · 103 ms−1 , P = 1.05 · 10 m Ks 3 2 −1 αWS W−1 , βSWS = 2.71 · 103 ms−1 , S = 0.88 · 10 m Ks

(2.82)


95

and D DS D VP = αD P k − βP , VS = αS k − βS

(dry rock),

(2.83)

where 3 2 −1 αD W−1 , βPD = 2.36 · 103 ms−1 , P = 1.12 · 10 m Ks 3 2 −1 αDS W−1 , βSD = 1.68 · 103 ms−1 . S = 0.77 · 10 m Ks

The reliability of these correlations is somewhat reduced by the fact that the conductivity was measured under uniaxial stress of 500 bars, whereas the wavespeeds were measured in a stress-free state. Besides, these relations make no reference to the properties of the bulk material and, therefore, do not explicitly interrelate changes due to porosity. In the work of Kim et al. (2005), several physical properties of aluminum foams (Al-3Si-2Cu-2Mg) were experimentally measured, such as electrical conductivity, Young’s modulus, and macroscopic yield stress σ y . The authors found that the following elasticity-conductivity correlation gives the best fit of the data: 4/3 2/3 k k E = 1.23 − 0.015 . (2.84) E0 k0 k0 However, the accuracy of this connection is somewhat reduced by the fact that it involves an intermediate interpolation, separately for E and k. The authors also give empirical connection between the macroscopic yield stress and the effective conductivity: 2/3 k k σy − 0.30 . (2.85) y = 1.15 k k σ0 0 0 3. Quantitative Characterization of Microstructures: General Considerations Quantitative characterization of microstructures means identification of the proper microstructural parameters, in whose terms the considered physical property (such as effective elasticity or conductivity) is to be expressed. The key requirement is that they should represent individual inhomogeneities – or, more generally, microstructural features – in accordance with their actual contributions to the property considered; otherwise, the property may not be a unique function of these parameters. For example, the crack density parameters for the

96


effective elasticity and effective conductivity take contributions of individual cracks proportionally to their sizes cubed. The proper parameters are, generally, different for different physical properties. For example, tensor crack density parameters for nonrandom crack orientations that have to be used in the effective elasticity and in the effective conductivity problems do not fully coincide. For materials that can be described as continuous matrices with inhomogeneities (cracks, pores, inclusions), such parameters should characterize the distribution of inhomogeneities over shapes, sizes, and orientations. They contain more information than just volume fractions and may be nontrivial, particularly in anisotropic cases of nonrandom orientations. The key step in their identification is finding individual inhomogeneity contributions to the property considered, followed by averaging over all the inhomogeneities in the representative volume V . For granular materials, or two rough surfaces pressed against each other, both the effective elasticity and the effective conductivity are controlled (aside from the bulk material properties) by contact geometries. In such cases, the microstructural parameters should characterize the distribution of contacts (their geometries, orientations, and spatial distribution). The key challenge is finding individual contact contributions to the property. The identification of the mentioned individual contributions and reducing them to simple forms is a challenging task; it requires distinguishing the microstructural features that have a dominant effect on the given property from the ones of minor importance and developing a sufficiently simple characterization of the dominant ones. The progress made in this direction is discussed in Section 4. The micromechanical approach, based on individual inhomogeneity contributions to the overall property, is rooted in a number of classical works. Mackenzie (1950) considered effective elastic properties of a solid with spherical pores on the basis of individual pore contributions to the overall compliance. Kröner (1958) analyzed the isotropic matrix with spherical anisotropic inhomogeneities and operated with a contribution of an individual sphere to the overall property. Hill (1965) considered ellipsoidal inhomogeneities of identical aspect ratios and expressed their contributions to the overall elasticity using Eshelby’s results (1957, 1961); dependencies on the ellipsoids’ aspect ratios were worked out in detail by Wu (1966). Walpole (1969) gave the mentioned dependencies in a more transparent form and, in the case of spheroids, reduced them to elementary functions. In the important case of cracks, their contributions to the overall elasticity and conductivity were given by Bristow (1960). A thorough review of the micromechanical approach was given by Markov (2000). If, for a given pair of physical properties, the individual inhomogeneity contributions – and, therefore, the microstructrural parameters – are sufficiently similar,


97

this leads to cross-property connections, elasticity–conductivity connection being a primary example. If, however, they are principally different, such connections cannot be established (at least, in a quantitative way). For example, effective elastic properties of a cracked material have relatively low sensitivity to appearance of clusters of several closely spaced cracks, whereas clustering is of key importance for the fracture-related properties.

3.1. Simplest Microstructural Parameters and their Limitations We start with overviewing several frequently used microstructural parameters. • For a material with ellipsoidal inhomogeneities of identical shapes (Hill, 1965) that is isotropic, overall, the volume fraction of inhomogeneities c=

1 $ (i) V V

(3.1)

i

is the adequate microstructural parameter (here, V (i) stands for the volume of ith inhomogeneity). Indeed, the overall elastic and conductive properties can be expressed in terms of c and the shape factor common for all inhomogeneities. • For cracks, their concentration is characterized by crack density parameters. In the isotropic case of randomly oriented circular cracks (of radii ai ), the scalar crack density parameter introduced by Bristow (1960) is ρ=

1 $ (i)3 a . V

(3.2a)

1 $ (i)2 a , A

(3.2b)

i

In the two-dimensional case, ρ=

i

where 2a(i) are crack lengths and A is the representative area. These definitions are rooted in the fact that the individual crack contributions to the overall compliance are proportional to their sizes cubed (squared, in 2D). For nonrandom crack orientations, the scalar crack density was generalized to second-rank crack density tensor in the work of Kachanov (1980) 1 $ 3 (i) 1 $ 2 (i) α= a nn a nn ). (3.3) (in 2D case, α = V A i

i

98

I. Sevostianov and M. Kachanov In this work, the fourth-rank tensor β=

i 1 $ 3 a nnnn V

(3.4)

i

was identified as a second crack density parameter but shown to play a relatively minor role (provided crack faces are traction free). Here, n is a unit normal to a crack, and nn and nnnn denote dyadic products. • For a granular material consisting of spheres of radius R and nonconducting intergranular space, the effective conductivity (in the isotropic case) was expressed √ by Batchelor and O’Brien (1977) in terms of the parameter φN R−1 S, where φ is the volume fraction of spheres, N is the average number of contacts per sphere, and S is the contact area (assumed to be √ the same for all contacts). This parameter reflects the fact that product R−1 S represents the contribution of an individual contact to the overall conductivity. These microstructural parameters have certain limitations. The volume fraction (3.1) may be insufficient in the following cases: • Mixtures of inhomogeneities of diverse shapes. The proper parameters become nontrivial, as illustrated by a simple 2D example of randomly oriented elliptical holes (Section 4). Shape “irregularities” further complicate the matter. • Nonrandomly oriented inhomogeneities. The proper parameters are tensorial, and their rank is not immediately obvious. Crack density parameters (3.2–3.4) may be inadequate in the following cases: • Nonplanar cracks. • Cracks that are not traction free, such as sliding cracks under compression (in this case, the fourth-rank tensor (3.4) starts to play a major role, Kachanov, 1982, 1993) or fluid-filled crack-like pores of diverse aspect ratios (for which tensor (3.4) has to be modified, Kachanov and Shafiro, 1997). √ The parameter φN R−1 S for a granular material may become inadequate in cases of noncircular or non-Hertzian contacts. Remark For certain microstructures with known microgeometries, the simplest scalar microstructural parameters (volume fractions, crack density) may still be sufficient – provided they are supplemented by characteristics of this specific microgeometry. For example, for two families of parallel spheroids with different properties, the effective properties can be expressed in terms of their partial volume fractions (Taya and Chow, 1981). As another example, several families of parallel


99

cracks can be characterized, for the purpose of effective properties, by partial scalar crack densities, plus angles between the families (Piau, 1980). Such expressions are restricted to the particular geometries considered. If, for instance, an orientation scatter is introduced into examples above, the concentration parameters should be revised. Materials science applications increasingly address more complex microstructures – both man-made and naturally occurring. Examples are cortical bone (several systems of pores of diverse geometries and orientations); various sprayed materials (oblate, crack-like pores, mixed with round ones); various reinforced composites (that, in addition to embedded inhomogeneities, may develop microcracks or micropores); geological materials (intersecting fractures at large scale, nonflat microcracks mixed with intergranular pores of complex geometries at microscale). In such cases, the proper microstructural parameters may be entirely nontrivial. In summary, much attention has been paid in literature to constructing dependencies (3.5) effective property = f microstructural parameter . &' ( % ?

The argument of this function has received much less attention. This issue is discussed in Section 4.

3.2. Microstructural Parameters are Rooted in the Non-interaction Approximation Contributions of individual inhomogeneities to the overall property are affected by interactions between them. Consider, for example, a solid with parallel circular cracks of radius a that are either (A) coplanar or (B) stacked. In case (A), crack contributions to the effective compliances depend on a stronger than a3 (amplifying interactions); in case (B), weaker than a3 (shielding interactions). Strictly speaking, interactions should be reflected in the crack compliance contributions. The corresponding microstructural parameter would correctly reflect “relative weights” of individual cracks and would depend on locations of crack centers. The effective constants would then be linear functions of this parameter. However, incorporating interactions into the microstructural parameter may not be a practical approach – it amounts to solving the interaction problem. Therefore, microstructural parameters usually ignore the interactions and take contributions of individual inhomogeneities by treating them as isolated ones (in particular, they do not reflect the mutual positions of inhomogeneities). The effect of interactions

100


on the overall properties is then reflected in a nonlinear dependence of the property on the parameter that is defined in the non-interaction approximation. Although this approach is a practical and is taken in the present work, one should be aware of its limitations: • Beyond the non-interaction approximation, the effective property is, generally, a nonunique function of thus defined microstructural parameter. This may be acceptable if sufficiently narrow bounds can be constructed for this function, which is not always the case (pores and cracks are examples). Besides, constructing bounds in anisotropic cases is a difficult mathematical problem. • An attempt to account for the mutual positions of inhomogeneities, while retaining the microstructural parameter that does not reflect them, may or may not work. Consider, for example, a periodic arrangement of diverse inhomogeneities (diverse shapes or orientations). It is not clear, a priori, whether the effective properties can be represented in terms of the product of a usual microstructural parameter, rooted in the non-interaction approximation and certain periodicity parameter. Thus, the microstructural parameters obtained by summing the contributions of individual inhomogeneities – treated as isolated ones – to overall property are rigorously proper in the non-interaction approximation. It seems logical to use them in various approximate schemes that use the non-interaction approximation as the basic building block, by placing inhomogeneities treated as isolated ones into some “effective” environment-effective homogeneous matrix or effective uniform field (self-consistent, differential, Mori–Tanaka’s schemes). The accuracy of such schemes, however, has to be judged on the case-by-case basis. Having accepted the parameters defined in the noninteraction approximation, the main challenge is to incorporate shapes and orientations of inhomogeneities into these parameters.

3.3. Cases of Overall Isotropy We now consider materials that are isotropic, overall, and consist of an isotropic matrix and, generally, nonspherical inhomogeneities. For the overall isotropy, the inhomogeneities must have random distributions over orientations and over sizes and, in addition, uncorrelated mutual positions. The requirement of randomness of orientations and mutual positions can actually be somewhat relaxed, without affecting the overall isotropy. Since the elastic properties are characterized by a fourth-rank tensor, these distributions may have the hexagonal symmetry; for conductive properties characterized by a second-rank tensor, this requirement can be further relaxed by allowing the cubic symmetries as well.


101

Equivalent for conductivity

Not equivalent for elasticity

Fig. 3.1 For the conductive properties, any isotropic mixture of diverse inhomogeneities is equivalent to a certain volume fraction of spheres. This equivalence does not hold for the elastic properties.

Isotropic conductivity is characterized by one effective constant. Therefore, any isotropic mixture of diverse inhomogeneities is equivalent, in its effect on conductivity, to an appropriate volume fraction of spheres, that reflects both the volume fraction and the average shape of inhomogeneities. Isotropic elasticity is characterized by two independent effective constants. Therefore, there is, generally, no equivalence to spheres (Fig. 3.1).

3.4. Benefits of the Proper Microstructural Parameters Identification of the proper microstructural parameters yields the following benefits: • Mixtures of inhomogeneities of diverse shapes and orientations (that are typical for materials science applications) are covered in a unified way. • The overall anisotropy is identified: it is determined by the rank and symmetry of the tensor microstructural parameter. This issue is most relevant for the elastic properties since the conductive ones, being characterized by secondrank symmetric tensor, always have the orthotropic symmetry. Thus identified elastic anisotropy may possess symmetries that the geometrical patterns of microstructure may not have. • Guidance in quantitative modeling of various microstructural features. The proper parameters reflect those microstructural elements that have a dominant effect on the property considered and ignore less important “details.” For example, parameters for the elastic/conductive properties take the individual inhomogeneities’ contributions proportionally to their sizes cubed. This implies that small inhomogeneities can be ignored, unless they vastly outnumber the larger ones. Yet another example concerns pores of strongly oblate shapes (aspect ratios < 0.10–0.15): their aspect ratios – and,

102


therefore, porosity – are irrelevant for the elastic/conductive properties, and the concentration of pores should be characterized by the crack density parameter. • Design of microstructures for the prescribed effective properties. An example is given by plasma-sprayed thermal barrier coatings that must have low thermal conductivity in the direction normal to the coating and high elastic compliance in the direction parallel to the coating. This requires identification of the microstructural parameters that actually control the mentioned properties. • Recovery of information on microstructure from the effective properties. Such information recovery is, obviously, nonunique. Nevertheless, certain information can be extracted. Identification of the proper microstructural parameters is crucial; it is these very parameters that can be extracted. • It leads to explicit cross-property connections between different physical properties, if the controlling microstructural parameters for them are sufficiently similar. This is the case for the elasticity–conductivity connections that constitute the focus of the present work as well as the electric – thermal conductivity connection discussed in Section 5.8.

4. Materials with Isolated Inhomogeneities: Microstructural Parameters for the Effective Elasticity and Effective Conductivity We consider materials that can be described as a continuous matrix containing isolated inhomogeneities (cracks, pores, foreign particles). Motivated by materials science applications, we assume that the inhomogeneities have generally diverse shapes and orientations. The first problem is to identify the proper microstructural parameters – in other words, the proper parameters of concentration of inhomogeneities – in whose terms the property of interest (effective elasticity or effective conductivity) is to be expressed. As discussed in Section 3, such parameters must represent individual inhomogeneities according to their actual contributions to the considered property. We first discuss effective elasticity, where this problem is most challenging, and then proceed to effective conductivity. We focus on similarities between microstructural parameters for the two properties since the explicit elasticity– conductivity connections developed in Chapters 5 and 6 hinge on them. The similarities are not immediately obvious – the two physical properties obey different field equations and are characterized by tensors of different ranks (second-rank conductivity tensor versus fourth-rank tensor of elastic constants). One of the key


103

challenges is to represent the elasticity tensor (more precisely, its change due to inhomogeneities) in terms of certain second-rank tensor that can be related to the conductivity changes. The background material will be assumed isotropic, k0 is its conductivity and E0 and v0 are Young’s modulus and Poisson’s ratio. Although we focus on 3D microstructures that are of main interest for applications, several 2D models will be used as illustrations. In 2D cases, E0 and v0 will denote 2D elastic constants that coincide with 3D ones for plane stress; for plane strain, they are obtained from 3D ones by dividing them over 1 − vˆ 20 and 1 − vˆ 0 , respectively, where vˆ 0 is 3D Poisson’s ratio. In both cases, 2D bulk modulus is related to 2D constants E0 and v0 by K0 = E0 / (2 − 2v0 ). The elastic behavior is assumed to be linear. This may be a limitation if compressive loads are applied to a solid with narrow, crack-like pores. For the linear elastic modeling to be adequate in such cases, compressive loads should be sufficiently low, as not to cause noticeable pore closures. Results of this Section have been obtained mostly by Sevostianov and Kachanov (2002a) and Kachanov and Sevostianov (2005). Sections 4.1 to 4.6 focus on the elasticity-related microstructural parameters, and Section 4.7 on the conductivityrelated ones.

4.1. General Considerations We assume that the solid is subjected to “remotely applied” stress σ that, in absence of inhomogeneities, would have been uniform within representative volume V (“homogeneous boundary conditions,” Hashin, 1983). The problem of finding the effective elastic properties is best formulated in terms of the elastic potential in stress f(σ) (or in strain, g (ε)) since the structure of the potential aids in identification of the proper microstructural parameters. The effective compliances S ijkl are obtained by differentiation: εij = Sijkl σkl = ∂f/∂σij . We represent f(σ) as a sum f = f0 + f,

(4.1)

where f0 = [(1 + v0 )/2E0 ] σij σji − (v0 /2E0 ) (σkk )2 is the potential in the absence of inhomogeneities. This implies a similar sum for the effective com0 + S . As shown in the text to follow, the structure of f pliances: Sijkl = Sijkl ijkl implies the proper parameters of concentration of inhomogeneities.

104


We represent f as a sum of terms corresponding to inhomogeneities contained in V ⎛ ⎞ $ $ (p) $ 1 1 H(p) : σ ⎝≡ H σkl σmn ⎠, (4.2)

f =

f (p) = σ : 2 2 p klmn p where the fourth-rank compliance contribution tensor H(p) gives the extra strain, per reference volume V, due to the presence of the pth inhomogeneity:

ε(p) = H(p) : σ.

(4.3)

The H-tensors reflect shapes and orientations of inhomogeneities, and they scaled as characteristic sizes of inhomogeneities cubed. Treating the inhomogeneities as isolated ones, H-tensors were calculated for a number of 2D and 3D shapes (Kachanov et al., 1994; Sevostianov and Kachanov, 2002a). Thus, the structure of f identifies the general proper microstructural parameter, namely the sum $ H(p) (4.4) subject to symmetrization (ij ↔ kl for the ijkl components) imposed by (4.2). Summation over inhomogeneities can be replaced by integration over their orientations, if computationally convenient. Since the H-tensors represent individual inhomogeneities in accordance with their actual contributions to the effective elastic properties, using parameter (4.4) insures that the effective elastic constants are unique functions of this parameter, at least in the non-interaction approximation. This general parameter (4.4) covers, in a unified way, mixtures of inhomogeneities of diverse shapes and orientations. The challenges are: • to calculate this sum for the classes of inhomogeneity shapes that are of interest; • to explore whether it can be replaced by simpler parameters, most notably, by a second-rank tensor or by scalars, in cases of isotropy. A dual formulation is in terms of stiffness contribution tensors N(p) . Tensor N of an inhomogeneity gives the extra average stress in V due to its presence,

σ = N : ε, under the assumption that, in its absence, the strain field within the site of the inhomogeneity would have been uniform. The elastic potential in strains g(ε) is given by 1 $ (p) g = g0 + g = g0 + ε : N : ε, 2

(4.5)


105

where g0 = [E0 /2 (1 + v0 )] εij εji + [v0 E0 /2 (1 + v0 ) (1 − 2v0 )] (εkk )2 is the potential in the absence of inhomogeneities, thus identifying the parameter dual to (4.4) as $

N (p)

(4.6)

subject to the same symmetrization as (4.4). Similarly to H-tensors, N-tensors are calculated by treating the inhomogeneities as isolated ones. The H- and N-tensors are interrelated as follows. The overall compliance tensor of the representative volume containing one inhomogeneity, S0 + H, is the inverse of its stiffness tensor C 0 + N. Linearizing with respect to a small change due to −1 = S0 , we have the inhomogeneity and taking into account that C 0 N = −C 0 : H : C 0

(4.7)

or, in the case of isotropy, −Nijkl = λ20 Hmmnn δij δkl + μ20 Hijkl + λ0 μ0 δij Hmmkl + δkl Hmmij ,

(4.8)

where λ0 and μ0 are Lame constants of the background material. Remark That it is H (or N) tensors to which the summation is to be applied, has not always been clear in literature. For example, Johannesson and Pedersen (1998) suggested to average Eshelby’s tensor over orientations. The simplest way to see that this is not the quantity to be averaged is to observe that, in the isotropic case of random orientations of nonspherical inhomogeneities, the averaged Eshelby’s tensor coincides with the one for a sphere. However, it is generally impossible to match two effective isotropic constants by one parameter, the volume fraction of spheres. In other words, averaged Eshelby’s tensor is not a proper microstructural parameter. The dual formulations (4.2) and (4.5) would yield the same results if exact expressions for f and g were known, as in the limit of small concentration of ellipsoidal inhomogeneities. The choice between the two formulations is important in the context of the accuracy of various approximate schemes – formulated in terms of either H- or N-tensors. Of particular importance is application of the non-interaction results to finite concentration of inhomogeneities. For example, the potential in stresses (4.1) would yield the effective Young’s modulus (or other effective stiffnesses) in the form E/E0 = (1 + Kc)−1 ,

(4.9)

106


where c is the inhomogeneities’ concentration and K is some constant, whereas potential (4.5) leads to E/E0 = 1 − Kc.

(4.10)

The question arises which of the two results (4.9) or (4.10) is more accurate at nonsmall values of c. We cannot formulate a fully rigorous criterion of choice, and it seems that this problem has not received sufficient attention. The following criterion appears reasonable: the change due to inhomogeneities should not lead to the effective constants becoming negative when the concentration parameter reaches a certain value. Based on this criterion, the choice is clear in the cases of cracks and rigid discs: • For cracks, the potential in stresses f(σ) that implies summation of the compliance contributions of cracks is the preferred choice. This is in agreement with the fact that cracks are sources of extra strains, see Eq. (4.11) below. • In the opposite limit of rigid discs, similar considerations imply that g(ε) and N-tensors should be used. In-between these two extremes, the choice is less clear. For pores or inclusions that are softer than the matrix, the potential f(σ) appears preferable; for inclusions that are stiffer than the matrix, the opposite is true. We note that this recommendation may not be generally valid: inclusions may have, for example, low shear modulus and high bulk modulus. We now discuss various classes of inhomogeneities and explore the possibility to replace the general parameters (4.4) and (4.6) by simpler ones.

4.2. Quantitative Characterization of Cracks We first consider 2D rectilinear cracks when results are particularly transparent and then discuss 3D geometries that are of main interest for applications. 4.2.1. Two-dimensional Solid with Rectilinear Cracks Denoting crack lengths by 2a(p) and unit normals to cracks by n(p), the strain per representative area A has the form ε = S0 : σ +

1 $1 (bn + nb)(p) 2a(p) A p 2 , % &' (

ε

(4.11)


107

where the summation is over all the cracks in A (it may be replaced by integration over orientations, if computationally convenient) and vector b = < u+ − u− > is the average displacement discontinuity on a crack. Representation)(4.11), as well as its extension to pores in terms of integrals over pore boundaries (un + nu)ds, is an immediate consequence of a footnote remark of Hill (1963); in the explicit form, it was given, for example, by Vavakin and Salganik (1975). The following fact is of importance: for each crack, the vector b is parallel to the traction vector n · σ induced at the crack site (in a continuous material) by the applied loading σ: b=

␲a n · σ, E0

(4.12)

where E0 is the 2D Young’s modulus. This follows from equality of crack compliances in the normal and shear modes: if p and τ are uniform normal and shear tractions applied to crack faces, then the corresponding average displacement discontinuities are * + ␲a bn p = , (4.13) τ bτ E0 with the same proportionality coefficient ␲a/E0 . This implies that the potential change f = (1/2) σ : S : σ = (1/2) σ : ε due to multiple cracks of diverse orientations and sizes is 1 $1 1 1 $ (p) (bn + nb)(p) 2a(p) =

f = σ : n · σ · b(p) a(p) 2 A p 2 A p =

␲ ␲ 1 $ 2 (p) (σ · σ) : (σ · σ) : α, = a nn E0 A p E0

thus identifying the 2D crack density tensor 1 $ 2 (p) a nn , α= A

(4.14)

(4.15)

as the proper crack density parameter. We emphasize that it is not introduced a priori but is implied by the structure of f. Being a sum of symmetric dyads, it is a symmetric second-rank tensor. It generalizes the 2D scalar crack density ρ = (1/A) a(p)2 : its linear invariant tr α = ρ. For randomly oriented cracks, α = (1/2) ρ I, where I is 2D unit tensor; for parallel cracks, α = ρ nn. Using tensor α as the crack density parameter yields the following benefits: • The effective constants are obtained in a unified form that covers all orientation distributions.

108


• It shows that all the details of cracks distribution over orientations and sizes (for example, orientation scatter about certain preferential orientation) that are relevant for the effective elastic properties enter through two parameters only – the principal values of α. • It identifies anisotropy due to cracks as orthotropy with principal axes coaxial to the ones of α (since α is a symmetric second-rank tensor). This result may not be intuitively obvious; it applies to any orientation distribution of cracks (for example, to several families of cracks forming arbitrary angles with each other). Moreover, the orthotropy is of a rather special type, characterized in the 2D case by only three independent constants (Kachanov, 1980, 1993). The possibility to characterize an arbitrary field of cracks by α, without involving tensors of higher ranks, is due to equality of the normal and shear crack compliances (4.13). 4.2.2. Three-dimensional Solid with Circular Cracks For a circular (penny shaped) crack of radius a, the normal and the shear compliances are not equal. However, they are relatively close, differing by a factor of 1 − v0 /2. For multiple cracks, this leads to the following expression for the potential change (Kachanov, 1980): , 16 1 − v20 V0 (σ · σ) : α −

f = σ:β:σ , (4.16) 3 (2 − v0 ) E0 2 where α=

1 $ 3 (p) a nn V

is the 3D crack density tensor and fourth-rank tensor (p) 1 $ 3 β= a nnnn V

(4.17)

(4.18)

is the second crack density parameter that emerges due to the difference between the normal and shear crack compliances. The impact of the β-term is, typically, relatively small, due to the relatively small factor v0 /2. Direct computational studies show that it is even smaller than one may expect (Grechka and Kachanov, 2006a). Thus, retaining α as the sole crack density parameter constitutes a good approximation. This implies approximate orthotropy coaxial with the principal axes of α. Moreover, the orthotropy due to cracks is of a rather special “elliptic” type, characterized by only four independent constants (see Kachanov, 1980, 1993 for details). The concept of approximate symmetries of the elastic and conductive properties, which is used throughout the present work, is discussed in Appendix A.


109

Expression (4.16) and its approximate simplified form (without β-term) cover all orientation distributions of cracks in a unified way. We mention one orientation distribution that is relevant for many materials science applications – a preferential orientation with certain scatter. We describe this distribution by the following function, containing the scatter parameter λ (Sevostianov and Kachanov, 2000): 1 2 λ + 1 e−λϕ + λe−λ␲/2 (4.19) Pλ (ϕ) = 2␲ (0 ≤ φ ≤ ␲/2 is the angle between normal n to a given crack and the preferential orientation of n). The extreme cases of fully random and ideally parallel orientations correspond to λ = 0 and λ = ∞, respectively. Fig. 4.1 shows orientation patterns that correspond to several values of λ. This orientation distribution is transversely isotropic. Therefore, the crack density tensor has two components: α11 = α22 = f1 (λ) ρ;

α33 = f2 (λ) ρ,

(4.20)

where ρ = tr α a is the overall crack density and: 2 18 − λ λ2 + 3 e−λ␲/2 λ + 3 3 + λe−λ␲/2 f1 = , f2 = . 6 λ2 + 9 3 λ2 + 9

(4.21)

20 1

2

3

15 l 5 2.5

l5 0 4

10

l 5 5.0

5

5 4

l5 7.5

l 5 10

5 3 2 0

0

1 p/4 w

p/2

Fig. 4.1 Orientation distribution function Pλ (ϕ) at several values of scatter parameter λ and the corresponding orientation patterns.

110


4.2.3. Cracks of Irregular Shapes The question arises, whether the findings above can be extended to noncircular cracks that are typical in material science applications; in other words, whether certain equivalent distribution of circular ones exists. For flat elliptical cracks, the answer is positive provided deviations from circles are random; moreover, the density of the equivalent distribution of circular cracks can be explicitly expressed in terms of the ellipses’ distribution (Kachanov, 1993). For a distribution of flat cracks of irregular shapes, computational studies of Grechka and Kachanov (2006b,c) show that the replacement by an equivalent distribution of circular cracks is possible as well, provided the shape irregularities are random. Therefore, the characterization by crack density tensor α can be retained, implying overall orthotropy. We mention one irregularity factor of particular importance – “islands” of cohesion between crack faces. These features are common in various microstructures (for example, in sprayed coatings). Such islands – even small ones – produce a strong stiffening effect, substantially reducing the density of equivalent circular cracks. The normal compliance of a circular crack with a concentric island is given by (Sevostianov and Kachanov, 2002b): 1 16a3 1 − v20 Hnnnn = V 3␲E0 % &' ( circular crack ⎡ √ √ 2 ⎤ λ2 2 2 3␲2 ⎣ 3 2 2 (2 − λ) + 2λ3 −λ − 1 ln (1 − λ) + − 1 ⎦, × 8 ␲ 2 ␲ % &' ( correction for island (4.22) where λ = c/a (ratio of internal and external radii of the annular crack). Fig. 4.2 shows radius of the equivalent circular crack in terms of the island size; an almost vertical drop indicates a strong stiffening effect of even a small island (the effect of an island on conductivity, relevant for cross-property connections, is also shown). Remark In the limit of λ 1 (narrow ring), we have approximately plane strain conditions and Hnnnn = 2␲ac2 1 − v2 /E, as expected (multiplier 2␲a represents the length of the ring). In the limit of λ → 1, Hnnnn , formally speaking, should approach 16 1 − v2 a3 / (3E) – its value for the circular crack of radius a. Eq. (4.22) does not yield this limiting value; moreover, the logarithmic term tends to infinity in this limit. This is due to the fact that the value of K I used


111

1.00

s

c r r 5a 2 c

Reff /a

0.75 a

0.50 n0 5 0.10 n0 5 0.25 n0 5 0.50

0.25

r5a s

0.00 0.00

0.25

0.50 l 5 a/c

0.75

1.00

Fig. 4.2 Annular crack and the radius of the equivalent circular crack as function of λ = a/c at various values of the Poisson s ratio of the matrix.

in the derivation of (4.22) is an approximation of numerical results that may have up to 3% error. However, even at 1 − λ = 10−20 , Hnnnn , as given by (4.22), still remains lower than Hnnnn for the circular crack. For irregular crack geometries with an island, the possibility to replace a random (in the sense of shapes) distribution of such cracks by an equivalent set of circular ones hinges on the equality of the normal crack compliances Hnnnn to the average, over the in-plane directions, shear crack compliances. Computational studies of Grechka and Kachanov (2006a) show that this equality holds with good accuracy so that characterization by crack density tensor can be retained, with reduced effective value of α. Remark Results for cracks apply, with good accuracy, to strongly oblate pores (aspect ratios smaller than 0.10–0.15). Indeed, as shown by Kachanov et al. (1994), the correction to the compliance contribution due to nonzero opening is of the order of the aspect ratio. Therefore, the effect of such pores on the elastic properties is close to the one of cracks, and they can be characterized by crack the density parameters. As a consequence, porosity is an irrelevant parameter for microstructures containing strongly oblate pores. We now discuss general inhomogeneities. We first illustrate the issue of proper parameters on a simple 2D example of elliptic holes and then proceed to 3D geometries.

4.3. Example: Two-dimensional Elliptic Holes This example demonstrates the guidance provided by the elastic potential in identification of the proper microstructural parameters. The compliance

112


contribution tensor of an elliptical hole has the form (Kachanov et al., 1994) . (a + b)2 1 ␲ (mn + nm) a(2a + b)nnnn + b(2b + a)mmmm + H= E0 A 2 (mn + nm) − ab (mmnn + nnmm)] ,

(4.23)

where a and b are semi-axes and m, n are unit vectors along them. It is not obvious at all that the sum H (p) can be expressed in terms of a symmetric second-rank tensor. However, the potential change due to the hole, after some algebra, takes the form: 0 1 ␲/

f = ab 4σ : σ − (trσ)2 + 2 (σ · σ) : a2 nn + b2 mm − abI . 2E0 A (4.24a) For a mixture of elliptic holes of diverse eccentricities and orientations, we have, therefore,

f = where

0 1 / 2σ : σ − (trσ)2 p + 2 (σ · σ) : ω , 2E

(4.24b)

p=

1 $ (ab)(r) ␲ A r

ω=

(r) 1 $ 2 ␲ a nn + b2 mm (second-rank hole concentration tensor). A r

2D porosity

The structure of f identifies the porosity p and the second-rank symmetric tensor ω as the proper microstructural parameters. In the limit of cracks, p = 0 and ω/␲ reduces to the crack density tensor α. Note that no degeneracy occurs in this limit if parameters p and ω are used. In the case of circles, ω = pI(I is the 2D unit tensor) so that porosity p is the sole microstructural parameter. Representation (4.24b) covers all mixtures of diverse ellipses in a unified way (for example, a mixture of circular holes and cracks). In the isotropic case of randomly oriented ellipses, the tensor ω = (r) (r) 2 2 (␲/2A) a + b2 or, a + b2 I can be replaced by the scalar (1/A) equivalently, by the average eccentricity parameter 1 $ (r) q= ␲ a − b(r)2 . (4.25) A r


113

and the effective Young’s and bulk moduli in this case are: 1 1 E G K = = , , K0 1 + (2p + q) / (1 − ν0 ) E0 1 + 3p + q G0 1 = . 1 + (4p + q) / (1 + ν0 )

(4.26)

Thus, in the isotropic case, p and q constitute the proper microstructural parameters. In the limit of cracks, p = 0 and q/␲ reduces to the usual 2D scalar crack density. Remark If one wishes to plot the effective moduli in terms of one parameter only, Eq. (4.26) shows that this parameter should be different for the three moduli: (2p + q) for K, (3p + q) for E, and (4p + q) for G. We emphasize that microstructural parameters – p and ω in the general anisotropic case, and p and q in the isotropic case – are not introduced a priori but are implied by the structure of f and that they are nontrivial. They are necessary; expressing the effective constants in terms of some other parameters would be nonunique, even in the low concentration limit (as seen from (4.26), the effective moduli cannot be expressed in terms of porosity p alone).

4.4. Three-dimensional Inhomogeneities For the ellipsoidal inhomogeneities, the H- and N-tensors are expressed in terms of Eshelby’s tensor sijkl that is a function of ellipsoid’s geometry and Poisson’s ratio of the matrix (Eshelby, 1957, 1961; see, also, the book of Mura, 1987). Utilizing the solution of Eshelby’s problem in the form given by Kunin and Sosnina (1971), we relate uniform strains and stresses inside the ellipsoidal inclusion to the uniform field at infinity (either σij or εij ): (int)

εij

= ijkl εkl ,

(int)

σij

= ijkl σkl .

(4.27)

The strain and stress concentration tensors introduced by Wu (1966) are given by −1 1 0 − Cmnkl , ijkl = Jijkl + Pijmn Cmnkl −1 1 0 − Smnkl , ijkl = Jijkl + Qijmn Smnkl

(4.28)

114


−1 where the inverse of symmetric fourth-rank tensor Xijkl is defined by the rela −1 −1 tion Xijmn Xmnkl = Xijmn Xmnkl = Jijkl , and Jijkl = δik δlj + δil δkj /2 is the symmetrized fourth-rank unit tensor. Tensors P and Q can be expressed in terms of Eshelby’s tensor s: 0 Pijkl = sijmn Smnkl ;

0 (Jmnkl − smnkl ), Qijkl = Cijmn

(4.29)

and tensors P and Q , and are interrelated as follows: 0 0 0 0 Qijkl = Cijmn Jmnkl − Pmnrs Crskl , Pijkl = Sijmn Jmnkl − Qmnrs Sirskl , ∗ 0 ijkl = Sijmn mnrs Crskl ,

∗ 0 ijkl = Cijmn mnrs Srskl .

(4.30)

Utilizing these results, the compliance and stiffness contribution tensors of the inclusion are given by the equations -−1 , −1 V1 1 0 Sijkl − sijkl + Qijkl , Hijkl = V Nijkl =

-−1 , −1 V1 1 0 Cijkl − Cijkl + Pijkl , V

(4.31)

where V1 is the volume of the inhomogeneity. In particular, H = (V1 /V ) Q−1 for a pore and N = (V1 /V ) P−1 for a rigid inclusion. Remark It is seen that H- and N-tensors – quantities relevant for the effective properties – utilize an incomplete set of Eshelby’s tensor components since expressions in the brackets of (4.31) are symmetric with respect to (ij) ↔ (kl). This imposes three constraints on 12 components of Eshelby’s tensor for an ellipsoid (one constraint on six components, in the case of a spheroid). An important observation is that, since Eshelby’s tensor is independent of the elastic constants of the inhomogeneity, the H- and N-tensors for an inhomogeneity of arbitrary elastic properties can be explicitly expressed in terms of H- and Ntensors for a pore, or for a rigid inclusion, respectively: −1 V1 1 0 1 0 pore ˜ pore + Sklmn ˜ mnrs Sijkl − Sijkl H H − S , (4.32) Hijrs = klmn klmn V Nijkl =

−1 V1 1 rigid 0 1 0 ˜ rigid + Cklmn ˜ mnrs N N − C , Cijkl − Cijkl klmn klmn V

˜ = (V/V1 )H and N ˜ = (V/V1 )N. where H

(4.33)


115

Remark Chen and Young (1977) showed that Eq. (4.31) holds for an inhomogeneity of general shape as the zeroth approximation with tensor sijkl in (4.29) understood in terms of average over the inhomogeneity strain (discussed in detail by Rodin, 1996). If all inhomogeneities have identical shapes and their orientations are either (p) (p) random or strictly parallel, the general parameter H (or N ) can be replaced by volume fraction c plus the shape factor (that, for ellipsoids, is known). For some simple mixtures of diverse ellipsoids, partial volume fractions may still be adequate as microstructural parameters. An example is given by two families of spheroids of two different aspect ratios, all of them strictly parallel (Taya and Chow, 1981). In the case of overall isotropy (random orientations of inhomogeneities), the general tensor parameter can be replaced by two scalars that reflect, in an integral way, the volume fraction of inhomogeneities and their distribution over shapes.

4.5. Spheroidal Inhomogeneities A surprising simplification of key importance is possible for a mixture of spheroids of diverse aspect ratios and orientations: the fourth-rank general parameter, (4.4) or (4.6), can be expressed, with good accuracy, in terms of certain symmetric second-rank tensor (and unit tensors). The possibility of such a representation was demonstrated in Section 4.3 for 2-D elliptic holes (in which case the representation is exact). We first consider a single spheroidal inhomogeneity (semi-axes are a1 = a2 and a3 and unit vector of the spheroid’s axis is n). In the text to follow, the largest semi-axis of the spheroid will be denoted by a (a = a1 for the oblate spheroids and a = a3 for the prolate spheroids). This definition of a leads to equations that cover, without degeneracy, the entire range of spheroid shapes, from a thin disc to a needle. Our analysis requires explicit analytic inversions and contractions of fourthrank tensors. They can be done by representing the tensors in terms of a “standard” tensor basis (Kunin, 1983; Walpole, 1984; see Appendix A). In the cases of the transversely isotropic symmetry, this basis consists of six tensors T(1) , . . . , T(6) , so that 6 6 pk T(k) , Q = qk T(k) , P= H=

k=1 a3 4␲γ t

V

3

k=1 6 k=1

(k)

hk T ,

6 a3 4␲γ t N= nk T(k) , V 3 k=1

thus reducing the problem to calculation of factors pk , qk , hk , and nk .

(4.34)

116


Representations for the H- and N-tensors involve power exponent t that is equal to 1 for the oblate shapes (γ < 1) and to −2 for the prolate shapes (γ > 1). The fact that aspect ratio γ enters (4.34) as either γ or γ −2 is rooted in the representation of the volume of a spheroid in terms of its largest semi-axis a. Using the representations for the stiffness and compliance tensors, Eshelby’s tensor and unit tensor in terms of the mentioned basis yields the following relations for coefficients pi , qi : 1 1 [(1 − κ) f0 + κf1 ], p2 = [(2 − κ) f0 + κf1 ], 2G0 2G0 κ 1 [1 − f0 − 4κf1 ], p3 = p4 = − f1 , p5 = G0 G0 1 [(1 − κ) (1 − 2f0 ) + 2κf1 ] p6 = G0

p1 =

(4.35)

and q1 = G0 [4κ − 1 − 2 (3κ − 1) f0 − 2κf1 ], q3 = q4 = 2G0 [(2κ − 1) f0 + 2κf1 ],

q2 = 2G0 [1 − (2 − κ) f0 − κf1 ] ,

q5 = 4G0 [f0 + 4κf1 ],

q6 = 8G0 κ [f0 − f1 ] ,

(4.36)

where κ−1 = 2 (1 − v0 ). The following functions of the aspect ratio γ are used hereafter: γ 2 2γ 2 + 1 g − 3 γ 2 (1 − g) , f1 (γ) = f0 (γ) = 2 , (4.37) 2 2 γ −1 4 γ2 − 1 where g (γ) =

⎧ ⎪ ⎨ √1 ⎪ ⎩

1−γ 2 √1 γ γ 2 −1

γ

√

1−γ 2

arctan γ , oblate shape (γ < 1) 5 ln γ + γ 2 − 1 , prolate shape (γ > 1).

(4.38)

If the material of an inhomogeneity is transversely isotropic, with the axis of elastic symmetry coinciding with the spheroid’s axis, the hk factors entering H-tensor in (4.34) are given by d d d ψ S1111 + S1122 ψ6 − 2S1133 4 d /ψ2 , , h2 = 2S1212 h1 = 4 (ψ1 ψ6 − ψ3 ψ4 ) d ψ d ψ S d ψ6 − S3333 S d ψ1 S1133 3 4 d h3 = h4 = 1133 /ψ5 , h6 = 3333 , , h5 = 8S1313 2 (ψ1 ψ6 − ψ3 ψ4 ) ψ1 ψ6 − ψ 3 ψ4 (4.39)

Connections between Elastic and Conductive Properties where ψ1 =

117

1 d d d + q1 S1111 − q3 S1133 + S1122 , 2

d ψ2 = 1 + 2q2 S1212 , d d d S1111 + q6 S1133 + S1122 ,

d d + q3 S3333 ψ3 = −2q1 S1133 , ψ4 = q3 d d d + 2q3 S1133 . , ψ6 = 1 + q6 S3333 ψ5 = 2 1 + q5 S1313

(4.40)

Factors nk entering N-tensor in (4.34) are d d d ϕ C1111 + C1122 ϕ6 − 2C1133 4 d /ϕ2 , , n2 = 2C1212 n1 = 4 (ϕ1 ϕ6 − ϕ3 ϕ4 ) n3 = n4 =

d ϕ − Cd C1133 6 3333 ϕ3 , 2 (ϕ1 ϕ6 − ϕ3 ϕ4 )

d /ϕ5 , n6 = n5 = 8C1313

d d ϕ ϕ1 − C1133 C3333 4 , ϕ1 ϕ6 − ϕ 3 ϕ4 (4.41)

where 1 d d d d + p1 C1111 − p3 C1133 + C1122 , ϕ2 = 1 + 2p2 C1212 , 2 d d d d d + p3 C3333 , ϕ4 = p3 C1111 + C1122 , (4.42) + p6 C1133 ϕ3 = −2p1 C1133 d d d ϕ5 = 2 1 + p5 C1313 + 2p3 C1133 . , ϕ6 = 1 + p6 C3333

ϕ1 =

We now write the general representation for the H- and N-tensor based on their transversely isotropic symmetry: H= ⎡

a3 1 V E0

⎤

⎢ ⎥ ⎢ ⎥ × ⎢ W1 II + W2 J + W3 (Inn + nnI) + W4 (J · nn + nn · J) + W5 nnnn⎥, &' ( ⎣% ⎦ isotropic terms (4.43a) a3 N = G0 V ⎡

⎤

⎢ ⎥ ⎢ ⎥ × ⎢ U1 II + U2 J + U3 (Inn + nnI) + U4 (J · nn + nn · J) + U5 nnnn⎥, ⎣ % &' ( ⎦ isotropic terms (4.43b)

118


where n is a unit vector of the spheroid’s axis and I and J are unit tensors of the second and fourth ranks. Coefficients Wi and Ui are functions of the aspect ratio γ as well as elastic constants of the matrix and the inhomogeneities. In the text to follow, they are referred to as “shape factors.” Using (4.34), we express them in terms of hi and ni : W1 =

4␲γ t E0 (h1 − h2 /2) , 3

W3 =

4␲γ t E0 (2h3 + h2 − 2h1 ) , 3

W5 =

4␲γ t E0 (h6 + h1 + h2 /2 − 2h3 − h5 ) , 3

U1 =

4␲γ t 4␲γ t 4␲γ t (n1 − n2 /2) , U2 = (2n3 + n2 − 2n1 ), n2 , U3 = 3G0 3G0 3G0

U4 =

4␲γ t 4␲γ t (n5 − 2n2 ) , U5 = (n6 + n1 + n2 /2 − 2n3 − n5 ) . (4.44b) 3G0 3G0

W2 =

4␲γ t E0 h2 , 3

W4 =

4␲γ t E0 (h5 − 2h2 ) , 3 (4.44a)

We now consider multiple inhomogeneities. We assume that the distribution over aspect ratios is statistically independent of the distributions over sizes and over orientations of inhomogeneities. This assumption allows one to repre(p) 3 (p) 3 (p) 3 (p) 3 sent sums Wa nn , Wa nnnn , Ua nn , Ua nnnn as products of the average shape factors ∞ wi =

∞ Wi (γ)F(γ)dγ,

ui =

0

Ui (γ)F(γ)dγ,

(4.45)

0

where F(γ) is the aspect ratio distribution density and second- and fourth-rank tensors ω=

1 $ 3 (k) a nn , V k

=

(k) 1 $ 3 a nnnn V

(4.46)

k

leading to the following representation E0 S − S0 = ρ(w1 II + w2 J) + [w3 (ωI + Iω) + w4 (ω·J + J·ω)] + w5 , (4.47a)


119

0 = ρ (u1 II + u2 J) + [u3 (ωI + Iω) + u4 (ω · J + J · ω)] + u5 , G−1 0 C−C (4.47b) 3 (k) where ρ = trω = (1/V ) a (in the case of cracks, it coincides with crack density); wi and ui are the average shape factors related to the individual shape factors Wi and Ui by (4.45) Remark Equations above assume that the distribution over aspect ratios is statistically independent of the distributions over sizes and over orientations of inhomogeneities (for a discussion in more detail, see Section 5.1). Explicit cross-property connections for a solid with multiple inhomogeneities hinge on the possibility to get rid of terms w5 in the sum H (p) by appropriately adjusting the coefficients at the other terms. More precisely, we seek to approximate terms σ : H (p) : σ in f by a linear combination of terms σ · σ : ω and (trσ)σ : ω where ω is a certain second-rank symmetric tensor. Alternatively, such approximations are sought for N (p) . In order to derive the mentioned approximation for multiple inhomogeneities, we start with approximating relations (4.43) for a single inhomogeneity by expressions in terms of the second-rank tensor nn, with terms containing nnnn omitted and coefficients at the remaining terms appropriately adjusted. Thus, we seek to approximate at least one of the H- and N-tensors by the expressions ⎡ ⎤ ⎢ ⎥ ⎢ ⎥ ⎢B1 II + B2 J +B3 (nnI + Inn) + B4 (nn · J + J · nn)⎥, (4.48a) &' ( % ⎣ ⎦ isotropic terms ⎡ ⎤

H=

a3 1 V E0

N=

⎢ ⎥ a3 ⎢ ⎥ G0 ⎢D1 II + D2 J +D3 (nnI + Inn) + D4 (nn · J + J · nn)⎥, (4.48b) &' ( % ⎣ ⎦ V isotropic terms

where a is the largest semi-axis whether the spheroid is oblate or prolate; factors Bi , Di are to be found. Representation (4.48a) requires that hi -factors obey the relation h6 + h1 + h2 /2 − 2h3 − h5 = 0

(4.49)

that, with the exception of a sphere, does not hold exactly. We now replace tensor H by a fictitious tensor Hˆ , with coefficients hˆ i obtained from hi by multiplication of hi by either (1 + δ) or (1 − δ) and choose δ in such a way that condition (4.49)

120


is satisfied exactly for hˆ i : hˆ 1 = h1 1 − δ sign h1 hˆ 2 = h2 1 − δ sign h2

hˆ 3 = h3 1 + δ sign h3 , hˆ 5 = h5 1 + δ sign h5 , hˆ 6 = h6 1 − δ sign h6 ,

(4.50)

where δ=

h6 + h1 + h2 /2 − 2h3 − h5 . |h6 | + |h1 | + |h2 |/2 + 2|h3 | + |h|5

(4.51)

The error of replacing H by Hˆ , estimated by the norm max ijkl, Hijkl =0 ˆ ijkl /Hijkl |, is equal to |δ|. Smallness of this norm guarantees that strain | Hijkl − H responses to all stress states of the actual and of the fictitious inclusions are close. Substitution of (4.50) into (4.44a) yields the factors Bi entering (4.48a): 4␲ 4␲ B1 = E0 γ t hˆ 1 − hˆ 2 /2 , B2 = E0 γ t hˆ 2 , 3 3 4␲ 4␲ B3 = E0 γ t 2hˆ 3 + hˆ 2 − 2hˆ 1 , B4 = E0 γ t hˆ 5 − 2hˆ 2 , (4.52) 3 3 where power exponent t = 1 for oblate shapes and t = −2 for prolate shapes. Similarly, the factors Di for the N-tensor are obtained as 4␲ t 4␲ t γ nˆ 1 − nˆ 2 /2 , D2 = γ nˆ 2 , 3G0 3G0 4␲ t 4␲ t D3 = γ 2nˆ 3 + nˆ 2 − 2nˆ 1 , D4 = γ nˆ 5 − 2nˆ 2 , 3G0 3G0 D1 =

(4.53)

where nˆ i are given in terms of ni by relations identical to (4.50). Figs. 4.3 and 4.4 show Bi and Di as functions of the aspect ratio, for several combinations of elastic constants. Note that nonsmooth behavior of B1 , B2 and D1 , D2 at γ = 1 is related to the definition of a in (4.52) and (4.53) as the largest semi-axis. Remark Figs. 4.3 and 4.4 show that in the limit γ → 0, the compliance and stiffness contributions of very “soft” inclusions (low, but finite ratios E1 /E0 ) tend to zero and thus do not converge to the ones of cracks. Indeed, cracks provide nonzero contributions due to displacement discontinuities across their faces. In contrast, for a soft thin inclusion (of a small but finite compliance), the difference between displacements of its two faces vanishes as the aspect ratio γ → 0. The case of a crack corresponds to setting v1 = 0, E1 = 0 and going to the limit γ → 0.


121

4

B1

5

2

6

4

0 3

2

22

1

24 0.01

0.1

1.0

10

100

10

100

10

100

15 1 2

B2 5

3

25

5

4

6

215 0.01

0.1

1.0

2 1

B3 1

2

0 3 21 22 0.01

4

5

6 0.1

1.0

5 1 3

B4

2

1

3 4

21 23 0.01

5

6 0.1

1.0

10

100

Fig. 4.3 Factors entering approximate expression (4.48a) for the compliance contribution tensor H as functions of inclusions aspect ratio γ. Poisson’s ratios v0 = v1 = 0.3 Curves 1 to 6 correspond to ratios E1 /E0 = 0.01, 0.1, 0.33, 3.0, 10, and 100.

122

I. Sevostianov and M. Kachanov 5 6 5 0 4 1

25

D1 210 0.01

3 2

0.1

1.0

10

100

10

100

10

100

10

D2

5 4

5

6

0 3

25 1 210 0.01

0.1

2

1.0

1 0

5

21

3

22

4

2

23 24

6

D3

25 0.01

1 0.1

1.0

2 6

1 0

4

21 22

3

5 2 1

23 0.01

D4 0.1

1.0

10

100

Fig. 4.4 Factors entering approximate expression (4.48b) for the stiffness contribution tensor N as functions of inclusion’s aspect ratio γ. Poisson’s ratios v0 = v1 = 0.3. Curves 1 to 6 correspond to ratios E1 /E0 = 0.01, 0.1, 0.33, 3.0, 10, and 100.

Connections between Elastic and Conductive Properties 15

0

10 4 5

25 0.01

3

0.1

26 29

0 1

2

23

2 Di

Bi

123

1

1 3

4

212 0.01

0.1

1

1

B1, D1

3

B3, D3

2

B2, D2

4

B4, D4

Fig. 4.5 Factors entering expressions (4.48a) and (4.48b) in the case of pores (oblate shapes). The curves are almost flat at γ < 0.15: strongly oblate pores produce the same effect as cracks.

Fig. 4.5 covers the case of oblate pores (for prolate shapes, the curves for very soft inclusions provide a very accurate approximation of pores). In particular, it provides the correct limit of a crack. In this limit, the curves become practically flat at aspect ratios smaller than 0.15, indicating that strongly oblate pores can be identified with cracks, as far as their effect on the linear effective elastic properties is concerned. Accuracy of the approximations for H- and N-tensors is illustrated in Figs. 4.6 and 4.7. These figures show that the accuracy is, generally, better for N- tensors. The accuracy of both approximations is generally good, particularly for pores (Fig. 4.8) but worsens considerably if the inclusion – matrix contrast in the bulk moduli is very different from the one in the shear moduli (such as fluid-like inclusions with negligible shear modulus). We note, in addition, that both approximations, for H- and N-tensors, become exact when Poisson’s ratio of the matrix v0 = 0; the approximation for N-tensor also becomes exact when v0 = 0.5. Remark The fact that the approximations in terms of a second-rank tensor lose accuracy when the mentioned two contrasts are very different is best explained on the example of cracks. For a dry crack, its compliances in the normal and shear modes are close, and this makes it possible to characterize a cracks solely by the second-rank crack density tensor α defined by (3.3). However, filling a crack with fluid (of negligible shear modulus) reduces its normal compliance but does not affect the shear one. The difference between the two compliances gives rise to fourth-rank tensor β defined by (3.4). Remark Since representations (4.48) are approximate, they are not interrelated by Eq. (4.7) that holds for the exact expressions of H and N (although it may hold approximately).

124

I. Sevostianov and M. Kachanov Rigid inclusions 100 v0 5 0.25 E0

0.01

g

1

100

v1 5 0.25

needle-like

crack-like

E1 v1 5 0.33 v1 5 0.45

0.01 Soft inclusions

E1

E0

E0

1

g


100

0.01

1

g

100

needle-like

E1 crack-like

0.01

Rigid inclusions 100 v0 5 0.45

needle-like

crack-like



Fig. 4.6 Accuracy maps for the approximate representation (4.48a) of H tensor in terms of a second-rank tensor. The combinations of parameters (elastic contrast E1 /E0 and aspect ratio γ) corresponding to accuracy better than 10% lie in the region centered at point 1 and bounded by the curves shown.

For materials with multiple inhomogeneities, the approximation in terms of the second rank tensor ω = (nn)(p) has the form: ⎤ ⎡ 3 $ a 1 ⎢ ⎥ + b2 J + b3 (ωI + Iω) + b4 (ω · J + J · ω)⎦, H (p) = ⎣ %b1 II &' ( V E0 isotropic terms (4.54a) ⎡ ⎤ 3 $ a ⎢ ⎥ G0 ⎣ d1 II + d2 J + d3 (ωI + Iω) + d4 (ω · J + J · ω)⎦, N (p) = % &' ( V isotropic terms (4.54b)


125

Rigid inclusions 100 v0 5 0.25 E1

0.01

1

g

100

v1 5 0.25

needle-like

crack-like

E0

v1 5 0.33 v1 5 0.45

0.01 Soft inclusions Rigid inclusions 100 v0 5 0.45 E1

0.01

1

g

100


crack-like

E0

needle-like

crack-like

E1

E0 0.01

1

g

100

needle-like



Fig. 4.7 Same as Fig. 4.6 for the N tensor.

where factors bi , di depend on the average, in a certain sense, aspect ratio of inclusions and on the elastic constants. These representations utilize, again, the statistical independence of the distributions over orientations and over aspect ratios. Remark Aside from being a key point for cross-property connections, representations (4.54) – if they are possible – have important implications for the overall elastic anisotropy: a solid with an arbitrary mixture of spheroidal inhomogeneities is approximately orthotropic (orthotropy axes are coaxial with the principal axes of ω). This result may seem counterintuitive since it covers cases when, geometrically, the patterns of inclusions’ distribution do not have the orthotropic symmetry (such as several families of parallel inclusions at arbitrary angles to each other). Moreover, the orthotropy is of a simplified (“elliptic”) type: the elasticity tensor is expressed in terms of symmetric second-rank tensor ω and is characterized by five independent elastic constants instead of nine. This generalizes a

126

I. Sevostianov and M. Kachanov 0.15

(a) 1

1

H

2

d

2

0.10

3

3 4

0.05

4

5

5 0.01

0.1

1.0 g

10

100

0.04

(b)

N

0.03

4

d

3

4 3 5

0.02

2

0.01

5 2

1

1

0.01

0.1

crack

1.0 g sphere

10

100 needle

1

v0 5 0.1

4

v0 5 0.4

2

v0 5 0.2

5

v0 5 0.5

3

v0 5 0.3

Fig. 4.8 Accuracy of the approximate representation of the pore compliance contribution tensor H (a) and pore stiffness contribution tensor N (b) as a function of aspect ratio γ for several values of the Poisson’s ratio v0 . Note a much higher accuracy (better than 4% in all cases) for tensor N.

similar finding for cracks when the number of independent constants is further reduced to four (Kachanov, 1980, 1993).

4.6. Microstructural Parameters for Conductive Properties: Comparison with Parameters for Elastic Properties Deep similarities exist between microstructural parameters for effective conductivity and effective elasticity. In particular, contributions of individual inhomogeneities to these properties depend on their sizes in the same way, and their orientation dependence is similar (although not identical). At the same time, there are differences in shape dependence of the mentioned contributions. The similarities lead to cross-property connections; the differences result in approximate


127

character of the connections and in their sensitivity – albeit mild – to the average shapes of inhomogeneities. We consider the thermal conductivity problem for a background material with isotropic conductivity k0 containing an inhomogeneity with the isotropic thermal conductivity k1 . Limiting cases k1 = 0 and k1 = ∞ correspond to an insulator and a superconductor. Assuming a linear conduction law (linear relation between farfield temperature gradient G and the heat flux vector U per representative volume V), the change in G required to maintain the same heat flux if the inhomogeneity is introduced is:

G = R · U,

(4.55a)

where the symmetric second-rank tensor R can be called the resistivity contribution tensor of an inhomogeneity. Treating the inhomogeneity as an isolated one allows one to calculate R-tensors for certain shapes, such as an ellipsoid or a crack with a cohesion island. Alternatively, this relation can be written in a dual form

U = K · G,

(4.55b)

where K is the conductivity contribution tensor of an inhomogeneity. Remark The problem of electric conductivity is mathematically identical to the thermal conductivity problem with the role of G played by the gradient of electric potential, and the role of U by the vector of electric current. In contrast with H ↔ N relation (4.7) in the elasticity problem, tensors R and K are simply proportional to each other. Indeed, the conductivity of the representative volume containing one inhomogeneity, k0 I + K, is inverse of the resistivity k0−1 I + R; linearization with respect to a small change due to the inhomogeneity implies R = −k0−2 K.

(4.56)

The two dual tensors yield dual formulations for the effective conductive properties of a material with multiple inhomogeneities in the non-interaction approximation: (A) The effective conductivity k is a sum k = k0 I +

$

K (p) .

(4.57a)

(B) The effective resistivity r is a sum r = k0−1 I +

$

R(p) .

(4.57b)

128


In the asymptotics of small concentration of inhomogeneities, Eqs. (4.57a) and (4.57b) coincide. An important practical question affecting the choice between the two is the accuracy of the non-interaction results in cases of finite concentration. From this point of view, the formulation remaining accurate at larger concentrations is preferable. This problem parallels the one encountered in the context of elastic properties, where the choice is between formulations where either compliance- or stiffness contribution tensors are summed up. It seems that there is no universal rigorous guidance for choosing between the two formulations. However, the following criterion – that is similar to the one taken in the context of elasticity – appears reasonable. If inhomogeneities are more conductive than the matrix, they are treated as sources of extra conductivity, leading to summation of the conductivity contributions (4.57a). If inhomogeneities are less conductive than the matrix, the formulation in resistivities (4.57b) is the one of choice. This criterion prevents the overall conductivity/resistivity from becoming negative at certain concentration of inhomogeneities. Thus, we identify the proper microstructural parameter for the conductivity problem as the sum over all inhomogeneities $ (4.58a) R(p) if k1 > k0 or, alternatively,

$

K (p) if k1 < k0 .

(4.58b)

Tensor R is expressed in terms of second-rank Eshelby’s tensor for conductivity sC : −1 V1 1 k0 C R= I−s , (4.59) V k0 k1 − k 0 where t = 1 for oblate shapes (γ < 1) and t = −2 for prolate shapes (γ > 1). For an ellipsoidal inhomogeneity, explicit expressions for sC are known. For spheroidal inhomogeneity of aspect ratio γ, relevant results were given by Carslaw and Jaeger (1959). They lead to the following expression for the Eshelby’s tensor: sC = f0 (I − nn) + (1 − 2f0 ) nn,

(4.60)

where n is the unit vector along the spheroid’s axis of symmetry and function f0 (γ) is defined by (4.37). Substitution into (4.59) yields K = −k02 R =

a3 k0 (A1 I + A2 nn), V

(4.61)


129

where dimensionless factors A1 and A2 (plotted in Fig. 4.9) are as follows: 1 k0 − k11 4␲γ t 1 , 3 k0 + k11 − k0 f0 (γ) 2 1 k33 − k0 (1 − 3f0 (γ)) 4␲γ t 1 1 1 . A2 = 3 k33 − 2 k33 − k0 f0 (γ) k0 + k33 − k0 f0 (γ)

A1 =

(4.62)

In particular, for a sphere, γ = 1 and f0 = 1/3; for a cylinder, γ → ∞ and f0 = 1/2. For a crack, γ → 0 and 1 8a3 1 R= nn. (4.63) V 3 k0 Remark Similarly to the elasticity problem, R for a crack can be used, with good accuracy, for strongly oblate pores (aspect ratio γ smaller than 0.10–0.15). Indeed, Fig. 4.9 shows that A1 A2 for the strongly oblate shapes, whereas A2 is almost flat at small γ. One has to be careful, however, with applying these results to overly 10 1 2 3

5 0

4 5

25 210 215 0.01

6

A1 0.1

6

1.0

10

100

10

100

6

4 1

5

2

3

0 22 24 0.01

2

4

A2 0.1

1.0

Fig. 4.9 Factors Ai entering expressions for the conductivity and resistivity contribution tensors as functions of inclusion’s aspect ratio γ. Curves 1 to 6 correspond to ratios k1 /k0 = 0, 0.1, 0.33, 3.0, 10, and 100.

130


narrow cracks. As noted by Zimmerman (1996), cracks with aspect ratios smaller than 0.01 may not be accurately modeled as insulators since the contribution from conductivity through air becomes significant. For a thin superconducting disk (γ → 0, k1 = ∞), formulation in terms of the conductivity contribution tensor is more appropriate: K=

16a3 k0 (I − nn). 3

(4.64)

For spheroids, the general microstructural parameter for the effective conduc tivity R( p) (or the dual parameter K ( p) that, in view of (4.56), is proportional to it) is specified as follows: (p) $ 1 1 $ 3 (p) 1 1 $ 3 R( p) = a A1 a A2 nn , I+ (4.65) V k0 V k0 implying that the proper microstructural parameters in this case are 3 (p) • Scalar V1 a A1 (in the case of identical aspect ratios γ, it reduces to the volume fraction times factor A1 ); (p) 3 • Second-rank symmetric tensor V1 a A2 nn . Assuming that the distribution over aspect ratios is statistically independent of the distributions over sizes and over orientations of inhomogeneities k0 r − I = I − k/k0 = a1 ρI + a2 ω,

(4.66)

where ω is given by (4.46) and ∞ ai =

Ai (γ)F(γ)dγ.

(4.67)

0

In the case of overall isotropy (random orientations of spheroids), the secondrank tensor in the last term in (4.65) is proportional to unit tensor I and adds up to the first term. The overall scalar coefficient at I is the proper microstructural parameter in this case. Generally, it does not reduce to the volume fraction but reflects the average – in the sense implied by (4.65) – aspect ratio. Comparing R- and K-tensors with H- and N-tensors of the elasticity problem, the following observations can be made. • In their size dependence, all these tensors are proportional to the inhomogeneity size cubed. • In their orientation dependence, the difference is that H- and N-tensors contain fourth-rank nnnn-terms (although, in many cases, they can be eliminated with satisfactory approximation, see Section 4.5).


131

• The main difference between (H, N)- and (R, K)-tensors is in their shape dependence. In the case of spheroidal shapes, this means differences between the aspect ratio dependencies of A1,2 -factors (in the conductivity problem) and of B1−4 - or D1−4 -factors (in the elasticity problem).

4.7. Inhomogeneities of Irregular Shapes In materials science applications, inhomogeneities often have “irregular” shapes. Their analysis requires both theoretical guidance and numerical studies. The main (and, perhaps, the only) general theoretical tool is provided by the so-called comparison (or “auxiliary”) theorem of Hill (1963). 4.7.1. Hill’s Theorem and its Implications This theorem focuses on changes in the effective properties caused by replacing inhomogeneities by inscribed/circumscribed shapes. Hill formulated it in energy terms; we rephrase it here in terms of compliances/stiffnesses. Let C 0 , S0 and C 1 , S1 be the stiffness/compliance tensors of the matrix and of the inhomogeneities, correspondingly (both, generally, anisotropic), and be the space occupied by all inhomogeneities. To be specific, we assume that the material of inhomogeneities is “softer” than the one of the matrix. More precisely, this means that the eigenvalues 1 − S 0 are nonnegative or, equivalently, that the eigenof the 6 × 6 matrix Sijkl ijkl 1 − C 0 are nonpositive. Let us enlarge (some of the values of the matrix Cijkl ijkl inhomogeneities are replaced by circumscribed ones, or new ones are introduced). Then the effective properties become “softer”: eigenvalues of the change in the effective compliance tensor Sijkl are nonnegative. The opposite inequality signs will hold, of course, if is shrunk. If the matrix and the inhomogeneities have the same type of elastic anisotropy and their anisotropy axes coincide, nonnegative eigenvalues of the difference S1 − S0 imply that each of the eigenvalues of S1 is not smaller than the corresponding eigenvalue of S0 ; the opposite inequality will hold for the stiffness tensor. In the fully isotropic case when (1) both the matrix and the inhomogeneities are isotropic and (2) inhomogeneity orientations are random so that the overall properties are isotropic, Hills’s theorem reduces to statements on the bulk and shear moduli, K and G. Assuming, for example, that G1 < G0 , K1 > K0 , Hill’s theorem reduces to an intuitively obvious statement that enlargement of inhomogeneities results in decrease of the effective shear modulus G and increase in the effective bulk modulus K. Remark The statement on K and G does not necessarily imply similar statements on Young’s modulus or Poisson’s ratio.

132


Taking the circumscribed/inscribed shapes as ellipsoids generates bounds that can be explicitly calculated (at least, in the case when the matrix is isotropic). The bounds are tight in the important case of strongly oblate inhomogeneities (that may be irregularly shaped) since both the circumscribed and the inscribed shapes can be taken as strongly oblate ellipsoids for which the compliance/stiffness contribution tensors are only weakly dependent on the aspect ratio. In general, however, the bounds formed by ellipsoids may be wide and hence less useful. Hill’s bounds can be somewhat narrowed, as follows. The space in-between the original shape and the circumscribed/inscribed ellipsoids is filled with smaller ellipsoids, with their contributions subtracted/added. However, as demonstrated for cracks of irregular shapes, the narrowing may be only moderate (Sevostianov and Kachanov, 2002b), due to a strong effect of the remaining ligaments. Hill’s theorem applied to the conductivity problem has the same implications as in the elasticity problem. Namely assuming, to be specific, that eigenvalues of kij1 − kij0 are nonnegative, the theorem implies that enlargement of inhomogeneities leads to nonnegative eigenvalues of the change kij of the effective conductivity (nonnegative change in the effective conductivity in any direction). Hill’s theorem implies that small scale shape details are unimportant as long as they do not change the connectivity of the region. In particular, it leads to the following observations: • Slight “jaggedness” of inhomogeneity boundaries can be ignored, as far as the effective properties are concerned. (In the case of crack-like pores, “jaggedness” is unimportant provided it does not produce contacts between crack faces). • It is unimportant whether various corner points of inhomogeneities are sharp or blunted since the difference between the two can be tightly bounded. • As discussed in Section 4.2, small partial contacts between crack faces produce strong effect on the compliance and resistivity of a crack. This does not contradict Hill’s bounds since such contacts change the connectivity of the region. Remark In the context of elasticity–conductivity connections, the irregularity of shapes may be less important, for the following reasons. If certain irregularity factor produces substantial but similar effects on the elastic and on the conductive properties, it is of minor importance for the connections. For example, small partial contacts between crack faces produce strong but almost identical effects on the elastic and the conductive properties, Fig. 4.10 (Sevostianov, 2003). Therefore, in the case of multiple cracks, reductions in the “adjusted” crack densities are very close for the two properties.


133

1.00

Reff /a

0.75

Elasticity problem

0.50

Conductivity problem 0.25

0.00 0.00

0.25

0.50

0.75

1.00

l Fig. 4.10 Reduction of the crack compliance (for different values of Poisson’s ratio) and resistivity contribution in the normal to the crack direction due to a cohesion island. Reff is the radius of an equivalent circular crack (producing the same effect). An almost vertical drop indicates that even a very small island produces a strong effect.

The relative importance of various microstructural features for the effective elastic and conductive properties is illustrated in Fig. 4.11. 5. Explicit Cross-property Connections for Anisotropic Two-phase Composites We now derive explicit conductivity–elasticity connections for materials that are anisotropic, overall, and can be described as isotropic matrices containing inhomogeneities of generally nonrandom orientations and diverse shapes. They have been developed recently by the present authors (Kachanov et al., 2001; Sevostianov and Kachanov, 2002a; Sevostianov, 2003). In the present section, we assume that the material of inhomogeneities is isotropic. Section 4 extends the connections to anisotropic inhomogeneities, for a broad class of composite microgeometries. The connections explicitly relate the entire set of anisotropic elastic constants to conductivities. This makes them well suited for various materials science applications, as demonstrated in Section 7. The connections are approximate, their accuracy dependent on the inhomogeneity shapes and on the elastic (but not the conductive) properties of the constituents. The connections are based on similarities between the microstructural parameters that control the conductive and the elastic properties (parameters of inhomogeneities’ concentration in whose terms the said properties are to be expressed).

134

I. Sevostianov and M. Kachanov FACTORS THAT HAVE STRONG EFFECT ON OVERALL ELASTIC AND CONDUCTIVE PROPERTIES

Cohesion Islands between crack faces

Orientational scatter about a preferential orientation

Convexity/concavity of inhomogeneity shapes

vs

(same area) Strong (several times) reduction of crack contribution to overall constants

Effect on overall constants: of the first order in scatter parameter

Concave shapes have stronger effect on the overall properties

FACTORS THAT HAVE MINOR EFFECT ON OVERALL ELASTIC AND CONDUCTIVE PROPERTIES Moderate jaggedness of inhomogeneity boundaries

»

»

Sharpness of corner points

Non-circularity of multiple planar cracks (if uncorrelated with crack sizes and orientations)

»

»

»

Fig. 4.11 Influence of various “irregularity factors” on the elastic and conductive properties.

The connections are derived under two main assumptions: • The inhomogeneities are spheroidal (so that the diversity of shapes means diversity of the aspect ratios). • The non-interaction approximation (NIA). As discussed in the Introduction, these assumptions are actually much less restrictive than they may seem – the connections continue to hold under much broader conditions – at finite, or even large, concentrations of inhomogeneities


135

that, in addition, may have nonspheroidal, “irregular” shapes (see Section 5.6 and experimental data of Section 7). This is explained by the fact that both complicating factors – the interactions and the “irregular” shapes – affect the elastic and the conductive properties in a similar way, so that the connection between the two is not affected much.

5.1. Elasticity–Conductivity Connections: General Case The proper microstructural parameters for the elastic and conductive properties reflect the individual inhomogeneity contributions to the considered property. These contributions have dual forms: compliance (H ) ↔ stiffness (N ) contribution tensors (in the context of elasticity) and resistivity (R ) ↔ conductivity (K) contribution tensors (in the context of conductivity) leading to dual microstruc (i) (i) tural parameters, H ↔ N (i) and R ↔ K (i) . The cross-property connections relate one of the parameters of the first pair to one of the second pair, resulting in four different forms of the connections that have different accuracies. Changes in the effective resistivity tensor r and in the effective conductivity tensor k due to spheroidal inhomogeneities have the form (see Section 4.6): (i) 1 $ 3 a (A1 I + A2 nn) , k0 r − I = I − k/k0 = (5.1) V i

where n(i) is a unit vector along ith spheroid’s axis, k0 is the conductivity of the bulk material, and aspect ratio dependent factors A1,2 are given by (4.62). The changes in the effective compliance and the effective stiffness tensors are, correspondingly, . (i) (i) $ $ 1 E0 S − S 0 = II + a 3 B1 a 3 B2 J + V i i (5.2) 6 (i) (i) $ $ 3 3 + + , a B3 (Inn + nnI) a B4 (J · nn + nn · J) i

G−1 C − C0 = 0

1 V

i

.

$

a3 D1

i

(i)

II +

$

a3 D2

(i)

J+

i

(5.3) 6 (i) $ (i) $ 3 3 + , a D3 (Inn + nnI) a D4 (J · nn + nn · J) + i

i

where coefficients Bi and Di are given by (4.52) and (4.53).

136


These formulas apply to an arbitrary mixture of spheroidal inhomogeneities of diverse aspect ratios and orientations. They contain A-, B-, and D-factors that depend on the inhomogeneity aspect ratios and on material constants of the constituents. Since the conductivity factors A1,2 are different from the elasticity factors Bi and Di , changes in the conductive properties due to inhomogeneities (5.1) cannot, generally, be expressed in terms of changes in the elastic properties (4.47); these tensors may not even be coaxial. However, this difficulty is overcome if the aspect ratios of inclusions are not correlated with either their orientations n(i) or sizes a(i) . This statistical independence implies that coefficients Ai , Bi , and Di can be replaced by their mean values ∞ ai =

∞ Ai (γ)F(γ)dγ,

0

bi =

∞ Bi (γ)F(γ)dγ,

0

di =

(5.4)

Di (γ)F(γ)dγ, 0

(where F(γ) is the aspect ratio distribution density and functions Bi (γ), Di (γ), and Ai (γ) are given by Eqs. (4.52), (4.53), and (4.62)) and taken out of the summation signs. The three tensors S, C, and k can then be expressed in terms of the same second-rank symmetric tensor 1 $ 3 (k) a nn . (5.5) ω= V k

In terms of this tensor and its trace ρ = (1/V )

3 (k) a , we have

k0 r − I = I − k/k0 = a1 ρI + a2 ω, (5.6) E0 S − S0 = ρ (b1 II + b2 J) + [b3 (ωI + Iω) + b4 (ω · J + J · ω)] , (5.7a) 0 G−1 C − C = ρ (d1 II + d2 J) + [d3 (ωI + Iω) + d4 (ω · J + J · ω)] . 0 (5.7b) Remark The above-mentioned statistical independence assumes a sufficiently large sample, that is, a sufficiently large number of diverse pairs {γ (i) , (a3 nn)(i) }, as in the case of distributions that can be described by continuous functions. In the case of two or three families of parallel inclusions, the requirement of statistical independence may be relaxed: within each family, the distributions over inclusion aspect ratios and sizes must be uncorrelated, but these distributions may be different for each of the families (this was shown by Kachanov et al., 2001 in the context of porous materials; the results can be extended to general


137

inhomogeneities). In the case of one family of parallel inhomogeneities, statistical independence of γ’s and a’s is unnecessary for the representations (5.6, 5.7) to hold. If it does take place, then b1−4 , d1−4 , and a1,2 are mean values of factors B1−4 , (i) (i) D1−4 , and A1,2 ; otherwise, they are mean values of products Ba3 , Da3 , (i) and Aa3 . In order to derive the cross-property connections in the general case of the orientation distribution, we express tensor ω in terms of r or, alternatively, in terms of k, from (5.6): 1 a1 k0 tr(r) − 3 (k0 r − I) − ρI, ρ = , a2 a2 3a1 + a2 a1 3k0 − tr(k) 1 (I − k/k0 ) − ρI, ρ = ω= . a2 a2 k0 (3a1 + a2 )

ω=

(5.8a) (5.8b)

Substituting either of these equations into (5.7) yields a cross-property connection – a closed form expression of the effective elastic constants in terms of the effective conductivities. Since each of the relations (5.8) and (5.7) has two forms, four forms of the cross-property connection can be constructed. Below, we give two of them: the compliance–resistivity connection: E0 S − S0 = (α1 II + α2 J)[k0 tr(r) − 3] + α3 [(k0 r − I) I + I(k0 r − I)] + α4 [(k0 r − I) · J + J ·(k0 r − I)] ,

(5.9a)

(where α1 = (b1 a2 − b3 a1 )/[a2 (a2 + 3a1 )], α2 = (b2 a2 − b4 a1 )/[a2 (a2 + 3a1 )], α3 = b3 /2a2 and α4 = b4 /2a2 ) and the stiffness–conductivity connection C − C 0 /G0 = (β1 II + β2 J)[tr (k/k0 ) − 3] + β3 [(k/k0 − I) I + I (k/k0 − I)] + β4 [(k/k0 − I) · J + J · (k/k0 − I)] , (5.9b) where β1 = −(d1 a2 − d3 a1 )/[a2 (a2 + 3a1 )], β2 = −(d2 a2 − d4 a1 )/[a2 (a2 + 3a1 )], β3 = −d3 /2a2 and β4 = −d4 /2a2 . Remark In addition to the case of statistical independence, the derived crossproperty connections also hold in the case when all the inhomogeneities have the same aspect ratio (and the same material properties). These connections apply to the general anisotropic case and cover all aspect ratio and orientation distributions in a unified way. They contain no fitting parameters. In particular, their dependence on aspect ratios is explicitly given by shape factors α1−4 and β1−4 . Both connections (5.9a,b) are approximate due to approximate

138


character of representations (5.7) of the elasticity tensor in terms of ω. The second one, (5.9b), tends to be more accurate, especially in the case of low compressibility of the matrix material. Factors α1−4 (or β1−4 ) depend on the aspect ratio distributions. Their presence reflects the fact that inclusion shapes affect the elastic and the conductive properties somewhat differently (otherwise, the cross-property connections would have been shape independent). However, the shape dependence is relatively mild even if all inclusions have the same aspect ratio, as illustrated by Fig. 5.1 for porous materials and Fig. 5.2 for two different composites. It vanishes if there is a substantial scatter in aspect ratios, see Section 5.4. For applications, it is convenient to have the cross–property connections in terms of tensor components. The compliance–resistivity connection (5.9a) has the following form in the principal axes of both the effective resistivity and the effective elastic orthotropy (with resistivities expressed in conductivities): E0 S1111 − 1 = (α1 + α2 + 2α3 + 2α4 ) ,

k0 − k11 k11

k0 − k22 k0 − k33 + (α1 + α2 ) + , k22 k33 0.5

2

4

1

1 0

3 0.1

1

1

3

20.5 21

2 21 0.01

2

0

10

21.5 100 0.01 v0 5 0.20

4 0.1

1

10

100

0.5

2

4

1

1 0 21 0.01

2

0

2 3 0.1

1

10

1 3

20.5

4 21 100 0.01 v0 5 0.30

0.1

1

10

100

Fig. 5.1 Coefficients α1−4 and β1−4 for a porous material as functions of average pore aspect ratio at two values of Poisson’s ratio v0 . In the limit of strongly oblate shapes, dependence on the aspect ratios vanishes (porosity is irrelevant for narrow, crack-like pores). Note strong dependence of β1−4 on the Poisson’s ratio.

Connections between Elastic and Conductive Properties 0.6 0.4

139

0.1

4

0.2

0.0 20.2

2

20.2

20.3

3

20.4 0.01

0.1

1

10

3

1

20.1

1

0.0

2

20.4 0.01

100

4

0.1

1

10

100

Copper reinforced with diamond particles 0.6 0.4

0.1

4

0.0

0.2 0.0

20.1

3

20.2

2

20.2 20.4 0.01

1

0.1

2

3

1

4

20.3 0.01

1 10 100 0.1 1 Poly(phenylene sulfide) reinforced with glass particles

10

100

Fig. 5.2 Coefficients α1−4 and β1−4 as functions of average pore aspect ratio for copper reinforced with diamond particles (E0 = 120 GPa, v0 = 0.34, k0 = 406 W/m · K, E1 = 1146 GPa, v1 = 0.07, k1 = 2000 W/m · K) and for poly(phenylene sulfide) reinforced with glass particles (E0 = 4 GPa, v0 = 0.4, k0 = 20 W/m · K, E1 = 76 GPa, v1 = 0.25, k0 = 104 W/m · K).

E0 S2222 − 1 = (α1 + α2 + 2α3 + 2α4 ) , + (α1 + α2 )

k0 − k11 k0 − k33 + , k11 k33

E0 S3333 − 1 = (α1 + α2 + 2α3 + 2α4 ) ,

k0 − k22 k22

k0 − k33 k33

k0 − k11 k0 − k22 + (α1 + α2 ) + , k11 k22 , k0 − k33 k0 − k11 k0 − k22 + , E0 S1122 + v0 = (α1 + α3 ) + α1 k11 k22 k33 , k0 − k22 k0 − k11 k0 − k33 + α1 E0 S1133 + v0 = (α1 + α3 ) + , k11 k33 k22 , k0 − k11 k0 − k22 k0 − k33 + α1 E0 S2233 + v0 = (α1 + α3 ) + , k22 k33 k11 (5.10a)

140

I. Sevostianov and M. Kachanov ,

k0 − k33 k0 − k11 k0 − k22 + , + 2α2 k11 k22 k33 , k0 − k22 k0 − k11 k0 − k33 + 2α2 2E0 S1313 − (1 + v0 ) = 2(α2 + α4 ) + , k11 k33 k22 , k0 − k11 k0 − k22 k0 − k33 + 2α2 2E0 S2323 − (1 + ν0 ) = 2(α2 + α4 ) + . k22 k33 k11 2E0 S1212 − (1 + v0 ) = 2(α2 + α4 )

The dual stiffness–conductivity connections are 0 C1111 − C1111 k11 − k0 = (β1 + β2 + 2β3 + 2β4 ) G0 k0 , k22 − k0 k33 − k0 + (β1 + β2 ) + , k0 k0 0 C2222 − C2222 k22 − k0 = (β1 + β2 + 2β3 + 2β4 ) G0 k0 , k11 − k0 k33 − k0 + (β1 + β2 ) + , k0 k0 0 C3333 − C3333 k33 − k0 = (β1 + β2 + 2β3 + 2β4 ) G0 k0 , k11 − k0 k22 − k0 + (β1 + β2 ) + , k0 k0 , 0 C1122 − C1122 k33 − k0 k11 − k0 k22 − k0 = (β1 + β3 ) + , + β1 G0 k0 k0 k0 , 0 C1133 − C1133 k22 − k0 k11 − k0 k33 − k0 + β1 = (β1 + β3 ) + , G0 k0 k0 k0 , 0 C2233 − C2233 k22 − k0 k11 − k0 k33 − k0 = (β1 + β3 ) + β1 + , G0 k0 k0 k0 , 0 C1212 − C1212 β2 + β4 k11 − k0 k22 − k0 β2 k33 − k0 = + , + G0 2 k0 k0 2 k0 , 0 C1313 − C1313 β2 k22 − k0 β2 + β4 k11 − k0 k33 − k0 + = + , G0 2 k0 k0 2 k0 , 0 C2323 − C2323 β2 k11 − k0 β2 + β4 k22 − k0 k33 − k0 + = + . G0 2 k0 k0 2 k0

(5.10b)


141

The utility of these connections is as follows. If the effective conductivity tensor k is known, then the only microstructural information needed to find the entire set of anisotropic effective elastic constants is the knowledge of the distribution of inclusion shapes (reflected in factors bi , di , and ai ). This information may be rather approximate since the shape sensitivity is mild (Section 5.4). Neither the orientation distribution nor volume fractions need be known. Without the cross-property connections, expressions for the effective elasticity tensors S and C require much more detailed microstructural information (that may not be available). Indeed, these expressions require knowledge of (1) volume fraction; (2) orientation distribution; and (3) aspect ratio distribution of the inhomogeneities. In contrast, if the cross-property connections are utilized, one needs to know only the aspect ratio distribution, and the sensitivity to this information is rather mild, so that the required information may be imprecise. Remark The accuracy of the cross-property connections (5.9) is determined by the accuracy of representing either H- or N-tensors of inclusions in terms of secondrank tensor nn (Eq. 4.48). In case this representation is exact, the cross-property connection is exact as well provided aspect ratios are statistically independent of orientations and sizes. The accuracy of representation of H- and N-tensors in terms of nn is determined by the following factors: A. Elastic contrast between the matrix and the inclusion (ratio E0 /E1 ). B. Poisson’s ratios v0 and v1 of the matrix and the inclusion. C. Aspect ratios of the spheroids. Estimates of the accuracy that cover various combinations of these factors are given in the form of “accuracy maps” in Figs. 4.6 and 4.7. Note that the accuracy maps are quite conservative. Experimental data discussed in Section 7 show that the actual accuracy may be much better.

5.2. Cases of Overall Isotropy and Transverse Isotropy In the case of transverse isotropy (x1 x2 being the isotropy plane), the connection (5.10a) can be rewritten in terms of the engineering elastic constants as follows: k0 − k11 k0 − k33 E0 − E1 = 2(α1 + α2 + α3 + α4 ) + (α1 + α2 ) , E1 k11 k33 k0 − k33 G0 − G12 k0 − k11 2(1 + ν0 ) = 2(α2 + α4 ) + α2 , G12 k11 k33 k0 − k33 E0 k0 − k11 ν0 − v21 = 2(α1 + α3 ) + α1 , E2 k11 k33

142

I. Sevostianov and M. Kachanov k0 − k11 k0 − k33 E0 − E 3 = 2(α1 + α2 ) + (α1 + α2 + 2α3 + 2α4 ) , E3 k11 k33 G0 − G13 k0 − k11 k0 − k33 2(1 + ν0 ) = (2α2 + α4 ) + (α2 + α4 ) , G13 k11 k33 E0 k0 − k33 k0 − k11 v31 = 2α1 + (α1 + 2α3 ) , (5.11) ν0 − E3 k11 k33

(of the first three relations, only two are independent) where Ei is the effective Young’s modulus in xi direction and Gij , vij are the effective shear moduli and Poisson’s ratios in plane xi xj . In the case of overall isotropy, relations (5.11) reduce to: k0 − k E0 − E = (3α1 + 3α2 + 2α3 + 2α4 ) , E k 3α2 + 2α4 k0 − k G0 − G = . G 2(1 + ν0 ) k

(5.12)

Isotropy takes place in one of two cases: (A) spherical inhomogeneities and (B) randomly oriented spheroids. In case (A), the cross-property connections (5.12) are exact and have especially simple form for spherical pores (Sevostianov et al., 2002): E0 − E (1 − ν0 )(9 + 5ν0 ) k0 − k = , E 7 − 5ν0 k G0 − G 5(1 − ν0 ) k0 − k = . G 7 − 5ν0 k

(5.12a)

In case (B), the connections are approximate since they are based on approxiˆ in terms of the second-rank tensor nn. mate representation (4.48a) of tensor H In this case, however, the exact cross-property connection can be established independently by utilizing the exact result (4.43a): E0 (14h1 + 7h2 + 12h3 + 6h5 + 4h6 ) k0 − k E0 − E = , E 10(3a1 + a2 ) k G0 (2h1 + 11h2 − 4h3 + 8h5 + 2h6 ) k0 − k G0 − G = . G 10(3a1 + a2 ) k

(5.13)

Connections (5.13) are useful in those cases when approximate Eq. (5.12) loses accuracy (see accuracy maps of Figs. 4.6 and 4.7). The approximate (5.12) and the exact (5.13) cross-property connections are compared in Fig. 5.3. It shows, in particular, that the accuracy of the approximate connection (5.12) is satisfactory for porous materials and may worsen considerably for rigid inclusions.

Connections between Elastic and Conductive Properties 2

0.8 0.6

1.5 1

1 10 Porous aluminum

2

0.2

2 0.1

1

0.4

1

0.5 0.01

143

100

0 0.01

0.1

1 10 100 Poly(phenylene sulfide) reinforced with glass particles

Exact connection

1 Coefficient at Young’s modulus

Approximate connection

2 Coefficient at shear modulus

Fig. 5.3 Comparison of the approximate and exact cross-property coefficients entering (5.12) and (5.13) for isotropic porous aluminum and poly(phenylene sulfide) reinforced with glass particles.

5.3. Materials with Cracks or Rigid Discs Specializing the cross-property connection (5.9a) for cracks, we obtain the compliance–resistivity connection in the form: S − S0 =

2(1 − v20 ) [(k0 r − I) · J + J · (k0 r − I)]. (2 − v0 )E0

(5.14)

In particular, a simple relation between the effective Young’s modulus Ei in certain direction xi and the conductivity ki (≡ ei · k · ei , no sum over i) in the same direction holds, for any orientation distribution of cracks, 4 1 − ν02 k0 − ki E0 − Ei = . (5.15) Ei 2 − ν0 ki These connection applies to strongly oblate pores as well. Remark The cross-property coefficient 4 1 − ν02 / (2 − ν0 ) entering crossproperty connection (5.15) for an arbitrary orientation distribution of cracks is close to the coefficient 2 1 − ν02 (10 − 3ν0 ) /5 (2 − ν0 ) in the connection (2.3) given by Bristow (1960) for randomly oriented cracks; they differ by the factor 1 − 0.3v0 . The difference between the two is due to the approximation involved in derivation of connections (5.9) and (5.15) (getting rid of the term containing fourth-rank tensor nnnn).

144


For a matrix of very low compressibility, ν0 close to 0.5, reinforced by thin discs, we introduce the following parameter – a ratio of two small values: ζ = (1 − 2ν0 )/␲γ.

(5.16)

We assume here that ζ > k0 ) that is relevant, for example, for metal-reinforced plastics. In the case of transversely isotropic orientation distribution, the cross-property connection has the form: 0 C1111 − C1111 0 C1111

= =

0 C1122 − C1122 0 C1122

0 C1313 − C1313 0 C1313

=

0 C3333 − C3333 0 C3333

(1 − 4v0 ) ␲γ [(k11 − k0 ) /k0 + (k33 − k0 ) /2k0 ], 4 (3 − 4ν0 ) 0 C1133 − C1133 0 C1133

=

(1 − 4ν0 ) (1 − ν0 ) ␲γ [(k11 − k0 ) /k0 + (k33 − k0 ) /2k0 ], 8ν0 (3 − 4ν0 )

=

8 (1 − ν0 ) [(k11 − k0 ) /k0 − (k33 − k0 ) /k0 ]. (7 − 8ν0 )

(5.19)

Remark Eq. (5.19) covers not only parallel discs but a random scatter about a certain orientation, as well as discs with normals that tend to lie in a plane and may have some scatter as well.


145

5.4. On the Sensitivity of Elasticity–Conductivity Connection to Shapes of Inhomogeneities Cross-property connections (5.9) require knowledge of α1−4 (or β1−4 ), that is, information on the certain average values of A, B, and D shape factors given by Eqs. (4.62), (4.52), and (4.53). The sensitivity to aspect ratios is an important issue since it determines the accuracy of information on γ’s that is required for the given accuracy of the connections. The sensitivity is, obviously, maximal when the inhomogeneities have identical aspect ratios; it is illustrated, in this case, by Figs. 5.1 and 5.2. This sensitivity, being relatively mild, becomes even smaller when a scatter in aspect ratios is present. Indeed, let us assume that γ = γ0 represents the maximum in the Gaussian distribution over γ: 1 −(γ − γ0 )2 ϕ(γ) = √ exp . (5.20) 2σ 2 σ 2π We examine the sensitivity to γ0 as a function of the standard deviation σ characterizing sharpness of the peak at γ0 (in the case of identical shapes, ϕ(γ) is a delta function, δ(γ − γ0 )). In the case of pores, Figs. 5.4 and 5.5 show the sensitivity (a)

(b)

1.5 4

1.0 0.5

0.5

1

2

1

0.0

3

2 0

4

1.0

1

0.0 20.5

1.5

3

20.5

4

2 0

() 5 (c)

(d)

1.5 4

1.0

2

3

4

1 exp 2(20)2/22 ŒW 2

[

]

0 5 1

5 0.5 5 1.0

0.5

0.5

1

0.0 20.5

1.0

1

3

2 0

1

2

5 2.0 5 5.0

3 3

4

0.0 0.0

2.0

4.0

Fig. 5.4 Sensitivity of factors α1−4 entering the elasticity–conductivity connection (5.9a) to pore aspect ratios distributed by Gaussian law (d) at different values of the standard deviation σ : (a) σ = 0.5, (b) σ = 1, (c) σ = 2.

146 (a)

I. Sevostianov and M. Kachanov (b)

1.5 1.0

1

1.0

2

4

0.0

(c)

1

2

0.5

0.5

20.5

1.5

3 0

4

0.0

1

2

3

4

3

4

20.5

3 0

1

2

3

4

1.5 1.0

1

2

0.5 4

0.0 20.5

3 0

1

2

Fig. 5.5 Sensitivity of factors β1−4 entering the elasticity–conductivity connection (5.9b) to pore aspect ratios, distributed by Gaussian law at different values of parameter σ : (a) σ = 0.5, (b) σ = 1, (c) σ = 2.

of α1−4 and β1−4 to γ0 in the range 0.3 < γ0 < 4.0. It is quite low at σ = 1 and almost vanishes at σ = 2. Thus, in cases of substantial scatter in pore shapes (σ > 1), factors α1−4 and β1−4 can be treated as shape independent constants. We further note that the shape sensitivity vanishes in two important limits: (1) thin, strongly oblate shapes (aspect ratio smaller than 0.10–0.15); (2) somewhat perturbed spherical shapes provided the perturbations are random (aspect ratios vary between 0.7 and 1.4).

5.5. Connection between the Degrees of Elastic/Conductive Anisotropies is Insensitive to Inhomogeneity Shapes As discussed above, the cross-property connections (5.9) have some sensitivity to inhomogeneity shapes. However, the connection between the extent of the elastic anisotropy (as measured by the ratios of Young’s moduli E1 /E2 and E1 /E3 ) and the extent of the conductive anisotropy (as measured by the corresponding ratios k1 /k2 and k1 /k3 of principal conductivities) has negligible shape sensitivity in the entire interval of shapes, cracks → spheres → needles. This is illustrated, for porous materials, by Fig. 5.6 in the case of general orthotropy and by Fig. 5.7 in the case of transverse isotropy. Thus, approximating the connections between the degrees of elastic and conductive anisotropies by the one corresponding, for example, to γ = 1/3, would result in errors not exceeding several per cent (4%, in the examples

1.00

1.00

0.90

0.80

E1/E2

E1/E2


k3/k0 5 0.6 0.80 0.70 0.80

0.85

0.90 k1/k2

0.95

1.00

0.60

E1/E3

E1/E3

0.70

0.80 k1/k2

0.90

1.00

1.00

0.80 k3/k0 5 0.6

0.40 0.20 0.50

k3/k0 5 0.8 0.60 0.40 0.60

1.00

147

0.60

0.70 0.80 k1/k3

0.90

0.80 k3/k0 5 0.8

0.60 0.40 0.60

1.00

0.70

0.80 k1/k3

0.90

5 0 (cracks)

5 3 (prolate pores)

51/3 (oblate pores)

1.00

∞ (cylinders)

Fig. 5.6 Very low sensitivity of the correlation between the extent of the elastic/conductive anisotropies to pore shapes. The case of transverse isotropy.

(a) 3.0

(b) 1.5

2.0

E1/E3

E1/E3

k3/k0 5 0.5

1.0 0.0 0.5

1.0

1.5

2.0

1.0

k3/k0 5 0.7

0.5 0.0 0.0

0.5

k1/k3

1.0

1.5

k1/k3

(c) 1.5 5 0 (cracks)

E1/E3

k3/k0 5 0.9 1.0

5 1/3 (oblate pores)

0.5

5 3 (prolate pores)

0.0 0.0

0.5

1.0

` (cylinders)

1.5

k1/k3

Fig. 5.7 Very low sensitivity of the correlation between the extent of the elastic/conductive anisotropies to pore shapes. The case of orthotropy.

148


shown in Figs. 5.6 and 5.7). This implies that the extent of elastic anisotropy can be estimated from the extent of conductive anisotropy independently of the microstructure.

5.6. On the Effect of Interactions and Nonspheroidal Inhomogeneity Shapes on the Cross-property Connections Cross-property connections (5.9) were derived under two assumptions: (1) inhomogeneities do not interact and (2) they have spheroidal shape. However, these assumptions are not as restrictive as they seem; the connections remain accurate well beyond these idealized cases. The underlying reason is that the mentioned complicating factors – interactions and nonspheroidal shapes – affect the two properties in a similar way so that the connection between the two is not affected much. 5.6.1. Interactions The effect of interactions on cross-property connections was first discussed by Bristow (1960) in the context of cracks. He provided experimental data on microcracked metals demonstrating that the cross-property connections derived in the non-interaction approximation continue to hold when changes in the effective properties due to cracks are substantial, implying that crack densities are not small and, therefore, the interactions are significant. He hypothesized that interactions affect both properties in a similar way so that the connection between the two is not affected. We illustrate Bristow’s hypothesis by two examples: (1) for coplanar cracks, the interaction has an amplifying effect for both properties (cracks’ contribution to the compliance and to the resistivity in the normal direction is greater than a sum of contributions of two isolated cracks); (2) for stacked cracks, the interaction has the opposite, shielding, effect for both properties. Although these examples have a limited scope (in particular, the shear mode of elastic interactions has no analogy in the conductivity problem), they give some support to the hypothesis. Further insight for cracks is provided by direct computational studies of the effective elasticity of 3D crack arrays (Grechka and Kachanov, 2006b). They suggest an additional explanation of accuracy of the cross-property connections at substantial crack densities. They show that, while crack interactions produce strong local effects, their influence on the effective elasticity is minimal provided the crack locations are more or less random (examination of the local fields shows that the competing interaction effects of stress shielding and stress amplification largely cancel each other). For conductive properties, such computations have not been done but similar cancellations can be expected.


149

This suggests that each of the properties separately is insensitive to interactions provided the crack locations are random (thus excluding, for example, the periodic arrangements). This explanation – specific for cracks – does not contradict Bristow’s hypothesis but complements it, providing an additional explanation of the accuracy. For inhomogeneities other than cracks, 3D computational studies of this kind have not been done, to the best of our knowledge. Instead, good accuracy of the connections is supported by substantial experimental data on diverse materials containing high concentrations of inhomogeneities (Section 7). Perhaps, the most convincing set of data concerns metal foams discussed in Section 7.1, where the volume fraction of pores is of the order of 0.70–0.90. It appears that Bristow’s hypothesis can be extended from cracks to general inhomogeneities. 5.6.2. Non-spheroidal Shapes In materials science applications, the shapes of inhomogeneities may be quite “irregular.” The question arises, whether the cross-property connections (5.9) derived under the assumption of spheroidal shapes can be used. One indication that this is likely to be correct is provided by the fact that, in the case of spheroids, the connections have rather weak sensitivity to the aspect ratios, and that this sensitivity becomes negligible if aspect ratios have some scatter (Section 5.4). This suggests that the sensitivity to shapes should be minimal in general. Further supporting arguments are as follows. For cracks of irregular shapes, Grechka and Kachanov (2006b) show that, as far as effective elasticity is concerned, multiple “irregular” cracks can be replaced by an equivalent set of the circular ones, provided the irregularities are random, and that this equivalence can be further extended to the intersecting crack configurations. Yet another supporting evidence is given by combined elasticity/conductivity calculations for cracks with “islands” of cohesion between the faces; although the effects of the “islands” on both the compliance and the resistivity contributions of cracks are quite strong, these effects are almost identical for the two properties (Sevostianov, 2003), see Fig. 4.10. For inhomogeneities other than cracks, we refer to experimental data of Section 7.

5.7. On the General Elasticity–Conductivity Constraints We derive the elasticity–conductivity constraints that are rigorous in the noninteraction approximation and hold for any orientation distribution of spheroidal inhomogeneities. Their number is, generally, insufficient for determination of the entire set of anisotropic elastic constants from the conductivity data, and therefore,

150


we call them constraints (rather than connections). However, they are sufficient in some special cases (discussed at the end of this subsection); besides, they are sufficient for determination of the conductive constants from the elasticity data. We apply contraction over the first two indices to C − C0 or S − S0 as given by (4.47). This eliminates the fourth-rank tensor (1/V ) (a3 nnnn)(k) and yields E0 (S − S0 ) : I = ρ(3w1 + w2 + w3 )I + (3w3 + 2w4 + w5 )ω

(5.21a)

0 G−1 0 (C − C ) : I = ρ(3u1 + u2 + u3 )I + (3u3 + 2u4 + u5 )ω

(5.21b)

(k) and its trace ρ = so that the second-rank tensor ω = (1/V ) (a3 nn) (k)3 0 can be expressed in terms of either C − C or S − S0 : (1/V ) a I : C − C0 : I , (5.22) ρ= G0 (9u1 + 3u2 + 6u3 2u4 + u5 ) C − C0 : I 3u1 + u2 + u3 I. −ρ ω= G0 (3u3 + 2u4 + u5 ) 3u3 + 2u4 + u5

(5.23)

Substituting (5.22) and (5.23) into the expression for conductivity (4.66) yields the cross-property constraint that can be formulated in four different forms involving different combinations of (k, r) ↔ (C, S) For example, the k ↔ C constraint has the form I − k/k0 =

((3u3 + 2u4 + u5 ) a1 − (3u1 + u2 + u3 ) a2 ) G0 (9u1 + 3u2 + 4u3 + 2u4 + u5 ) (3u3 + 2u4 + u5 ) a2 C − C0 : I 0 . (5.24) × I: C−C :I I+ G0 (3u3 + 2u4 + u5 )

This relation is fully sufficient for finding of the effective conductivity tensor from the elasticity data (but not vice versa). Note that this relation involves stiffnesses Ciijj but does not involve shear stiffnesses Cijij . We now apply contraction over the first and third indices to the same relation (4.47): = ρ (w1 + 2w2 + w4 /2) I + (2w3 + 5w4 /2 + w5 ) ω, (5.25a) S − S0 ijil C − C0 = ρ (u1 + 2u2 + u4 /2) I + (2u3 + 5u4 /2 + u5 ) ω. (5.25b) ijil


151

This gives yet another expression of tensor ω and its trace ρ in terms of C − C0 or S − S0 : C − C0 klkl , (5.26) ρ= 3u1 + 6u2 + 2u3 + 4u4 + u5 C − C0 kikj u1 + 2u2 + u4 /2 ωij = δij . (5.27) −ρ (2u3 + 5u4 /2 + u5 ) 2u3 + 5u4 /2 + u5 Substituting it into the conductivity/resistivity change (4.66) yields the second cross-property constraint. Its k ↔ C form is as follows k0 − kij a1 (2u3 + 5u4 /2 + u5 ) − a2 (u1 + 2u2 + u4 /2) = k0 G0 (3u1 + 6u2 + 2u3 + 4u4 + u5 ) (2u3 + 5u4 /2 + u5 ) C − C0 kikj 0 × C−C δij + a2 . (5.28) klkl G0 (2u3 + 5u4 /2 + u5 ) It involves shear stiffnesses C1212 , . . . and the diagonal stiffnesses C1111 , . . . but does not involve stiffnesses C1122 , . . . . Similarly to relations (5.24), they are sufficient for finding the conductivity tensor from the elasticity data (but not vice versa). Relations (5.24) and (5.28), written in components, constitute six cross-property constraints. In cases of transverse isotropy, there are four of them. Note that, although the effective elastic properties may be nonorthotropic, these relations involve only the orthotropic parts of tensors C − C0 or S − S0 . The utility of these constraints is as follows: A. Either of the constraints, (5.24) or (5.28), is sufficient for finding conductivities from the elasticity data. B. Being generally insufficient for the determination of the effective elastic constants from the conductivity data, they may become sufficient if some additional information on the elastic constants becomes available. In cases of overall transverse isotropy, only one additional relation is needed. They also become sufficient in the following special cases: • Overall isotropy. In this case, (5.24) and (5.28) are two independent relations that express the effective elastic constants in terms of one effective conductivity constant; they constitute an alternative form of connections (5.13). • Although generally insufficient in cases of transverse isotropy, they are sufficient in the case of parallel cracks (normal to the x3 axis). Indeed, in this case, cracks do not affect elastic compliances S1111 , S2222 , S1122 , S1212 so that the only changes due to cracks are the ones in S3333 and

152

I. Sevostianov and M. Kachanov S1313 = S2323 . Similarly, the conductivities k11 = k22 remain unaffected; k33 is the only one affected by cracks. Therefore, the two constraints – to which (5.24) and (5.28) reduce in this case – are sufficient for the determination of the compliance changes in terms of the change in k33 .

Another possible application of the constraints is to combine them with the approximate cross-property connections (5.9) that are based on elimination of (k) 3 from expressions for the effective the fourth-rank tensor (1/V ) a nnnn elastic properties. Such combining may, possibly, lead to better accuracy. This issue remains unexplored at the present moment. In Section 6, we will derive rigorous cross-property connections (without elimination of the mentioned fourth-rank tensor) that apply to certain classes of orientation distribution. In these cases, the constraints derived here coincide with some of these connections (in particular, in the case of parallel cracks discussed above, the constraints coincide with the entire set of the connections).

5.8. Connection between the Electric and the Thermal Conductivities Although the effective electric and the effective thermal conductivities are governed by mathematically similar laws, the connection between the two is immediately obvious. Indeed, the two terms entering the conductivity change due to inhomogeneities in the right-hand part of (5.6) cannot be represented as products of the conductivity parameters (k0 , k1 ) times purely geometric, ω-like parameters. Therefore, such a connection requires the same assumption as the conductivity– elasticity connection: statistical independence of the aspect ratio distribution and the distributions over inhomogeneity orientations n(k) and sizes a(k) . 3 (k) and ρ = Then, expressing the geometric parameters ω = (1/V ) a nn tr ω from the expression (5.6) treated as the electric conductivity relation and substituting them into the same expression treated as the thermal conductivity relation yield the following connection between the effective electric, r el , and thermal, rth , resistivities: (k0 r)th − I =

a2th a2el

ath ael − a2th a1el (k0 r)el − I + el1 2 (k0 tr r)el − 3 I. el a2 (3a1 + a2 )

(5.29)

In the case of overall isotropy (k0 r = I), this reduces to a very simple form: k0 r − 1 th k0 r − 1 el = . (5.30) 3a1 + a2 3a1 + a2


153

el and ath entering these connections and given by (5.4) are, The shape factors a1,2 1,2 el = ath and generally, different for the electric and the thermal conductivities: a1,2 1,2 cannot be expressed in terms of one another. This is seen from the structure of th factors Ael 1,2 and A1,2 ; they are given by combinations of aspect ratios and the electric/thermal conductivities of the phases, (k0 , k1 )el and (k0 , k1 )th , that do not reduce to products of the conductivity constants and purely geometric (aspect ratio-dependent) parameters.

5.9. Physical Properties that May Not Be Interrelated by Quantitative Connections The possibility to interrelate, in a quantitative way, a given pair of physical properties hinges on similarity between the microstructural parameters that control the two properties. As shown in the present review, this is the case for changes in the elastic and in the conductive properties due to the presence of inhomogeneities (pores, cracks, foreign particles). However, for the properties that are controlled by essentially different parameters, the correlations may be only qualitative, at best. We illustrate this statement on two pairs of physical properties: fracture–elasticity and permeability–elasticity. 5.9.1. Brittle Fracture versus Effective Elasticity The effective elastic constants of a material with defects (cracks, pores) are volume average quantities relatively insensitive to microstructural details such as mutual positions of defects – in particular, to their clustering. This is in contrast with the local quantities (such as stress intensity factors, SIFs) that generally control brittle fracture and are highly sensitive to the mentioned microscale factors. This essential difference is clear intuitively. In a more formal way, it follows, for example, from Rice’s (1975) theorem that relates volume average quantities to the microscale ones. In the context of effective elastic properties of a cracked solid, the theorem relates the said properties to the SIFs by representing cracks as having grown from small nuclei to their current configuration and taking integrals of SIFs over the growth path, as follows. For reference volume V containing a crack, the increment dSijkl of the overall compliance due to incremental propagation dl of the crack front L is given by: ∂Kq ∂Kr 11 cqr dSijkl = dl dL, (5.31) V4 ∂σij ∂σkl L

where Ki (i = 1, 2, 3) are modes I, II, and III SIFs and coefficients cqr relate the near-tip displacement discontinuity near the crack front to the local SIFs: [ui ] =

154


√ cij Kj r/2␲. We now treat the crack as having grown from an infinitesimal nucleus to its current geometry. Then crack compliance contributions Hijkl are given by integrals over the growth path: (5.32) Hijkl = dSijkl dl. In the case of multiple cracks, L stands for the collective front of all the cracks contained in V ; the SIFs will then reflect crack interactions. Aside from being a quantitative tool for evaluating Hijkl (Sevostianov and Kachanov, 2002b; Gorbatikh, 2004; Mear et al., 2007), Rice’s (1975) theorem provides an important insight of the qualitative nature; since Hijkl are integrals over the growth path, they are much less sensitive to various details of the crack geometries than the SIFs. In particular, for multiple cracks, the effect of crack interactions on the overall elastic constants is weaker than on the SIFs. Indeed, considering each crack as having grown from an infinitesimal nucleus, the interactions become noticeable only at close spacing, that is, they affect the integrand in (5.31) only at the last stages of the growth. (The low sensitivity of the effective elastic constants to crack interactions was also verified by direct computations, Grechka and Kachanov, 2006.) In particular, clustering of cracks – that is of obvious importance for brittle fracture – generally has little effect on the effective elasticity. This does not rule out statements of the qualitative nature – that the progression towards fracture via multiple cracking causes reduction of the effective elastic stiffness. These statements, however, are difficult to upgrade to stable quantitative connections. These issues, in relation to the damage mechanics, were discussed in more detail by Kachanov (1994). 5.9.2. Effective Elasticity Versus Effective Permeability The effective elastic properties of a cracked solid are expressed in terms of the crack density parameter. In the isotropic case, this is a scalar ρ that, for the circular cracks, is given by Eq. (3.2a). In anisotropic cases of nonrandom orientations, it is a symmetric second-rank crack density tensor α that, for circular cracks, is given by α = (1/V ) a(k)3 nn; irregularly shaped flat cracks with random irregularities are equivalent to a certain distribution of circular cracks and can thus be represented by α as well, where a(k) are treated as certain effective quantities, see discussion of Section 4.2. (The second crack density parameter – fourth-rank tensor β = (1/V ) a(k)3 nnnn – generally plays a minor role for traction-free cracks.) These parameters take the individual crack contributions proportionally to their linear sizes cubed, or to S (k)3/2 , where S (k) are their areas, in accordance with their actual contributions to the effective elasticity. Importantly, these parameters do


155

not depend on crack aspect ratios γ reflecting the fact that, for crack-like pores (γ 1), their contributions to the overall elasticity are almost independent of their opening and are the same as the ones of cracks. In contrast, the effective permeability of representative volume V crossed by several systems of cracks (fissures) – the issue relevant to geophysical applications – strongly depends on γ’s (the average fissure apertures). In the simplest models, the contribution of an individual fissure to the overall permeability is proportional to γ 3 (see, for example, Wittke, 1990). For multiple fissures, the proper microstruc tural parameter is, therefore, (1/V ) (Sγ 3 )(k) nn, where S is the fissure area. Hence, there is, generally, no quantitative connection between the effective elasticity and effective permeability. The tensors characterizing these properties may not even be coaxial (except for the case when all the fissures have identical opening and identical areas so that the parameter Sγ 3 can be taken out of the summation sign). In cases when fissures are not cracks but rough surfaces pressed against each other, the microstructural parameters for the elastic properties will reflect contact microgeometries (see Section 8), but they clearly do not possess the γ 3 -dependence so that the statement on the absence of the connection remains valid. Similarly to the “elasticity–fracture” pair, the above considerations do not rule out connections of the qualitative nature. For example, compressive stresses that reduce the permeability will also reduce the effective elastic compliance if they cause full or partial closing of fissures (Pyrak-Nolte and Morris, 2000). However, it is difficult to upgrade these statements to stable quantitative connections. 6. Cross-property Connections for Anisotropic Inhomogeneities The elasticity–conductivity connections (5.9), which cover all orientation distributions of inhomogeneities, are restricted to the isotropic inhomogeneities. Another restriction is that, for certain combinations of properties of the inhomogeneities and the matrix, the connections may become inaccurate, as seen from the accuracy maps of Figs. 4.6 and 4.7 (for example, when the inhomogeneity – matrix contrast in the bulk moduli is very different from the one in shear moduli). An alternative form of the connections can be developed for a broad class of orientation distributions – one, two or three families of approximately parallel inhomogeneities forming arbitrary angles with each other. It covers anisotropic inhomogeneities and has other advantages as well: • It is exact in the non-interaction approximation and has substantially higher accuracy at finite concentrations of inhomogeneities, as demonstrated by comparison with experimental data (Section 7.3).

156


• It remains accurate in cases when the general connections (5.9) lose accuracy, for example, when the inhomogeneity – matrix contrast in the bulk moduli is very different from the shear moduli contrast, such as fluid-like inclusions. This alternative form is first derived for parallel inhomogeneities. Then, we extend it to approximately parallel inhomogeneities (moderate orientation scatter) and, further, to two or three such families. This covers a large proportion of heterogeneous materials encountered in applications (microcracks having a preferential orientation, approximately parallel fibers, a mixture of the two, etc.) The alternative form is made possible by the fact that the main approximation involved in the cross-property connections (5.9) – getting rid of fourth-rank tensor nnnn in expressions for the compliance/stiffness contribution tensors – becomes unnecessary for parallel inhomogeneities. Instead, this tensor can be expressed in terms of second-rank tensor nn since nnnn = nn ⊗ nn. These alternative connections have two forms, depending on whether the orientation of parallel inhomogeneities is treated as a known parameter or not. If it is known, the connections have a simple linear form. If the orientation is not known, it has to be extracted from the conductivity/resistivity data. This leads to more complex nonlinear connections that cannot be extended to more than one family of approximately parallel inhomogeneities.

6.1. Cross-property Connections for Materials with Parallel Anisotropic Inhomogeneities For parallel spheroidal inhomogeneities, with unit vector n along the spheroids’ axes, Eqs. (4.66) for the effective conductivity/resistivity and (4.47) for the effective stiffness/compliance reduce to the form k0 r − I = I − k/k0 = ρ(a1 I + a2 nn),

(6.1a)

E0 (S − S ) = ρ [w1 II + w2 J + w3 (Inn + nnI) 0

+w4 (J · nn + nn · J) + w5 nnnn],

(6.1b)

(C − C )/G0 = ρ [u1 II + u2 J + u3 (Inn + nnI) 0

+u4 (J · nn + nn · J) + u5 nnnn].

(6.1c)

This allows one to express ρ in terms of either r or k, ρ=

tr(k0 r − I) tr(I − k/k0 ) = , 3a1 + a2 3a1 + a2

(6.2)

and substitute it into the elasticity relations, yielding the explicit elasticity– conductivity connection. It has four different forms, corresponding to four


157

combinations (resistivity, conductivity) ↔ (compliance, stiffness). The compliance – resistivity and the stiffness–conductivity connections are as follows: tr (k r − I) 0 [w1 II + w2 J + w3 (Inn + nnI) E0 S − S0 = 3a1 + a2 (6.3a) +w4 (J · nn + nn · J) + w5 nnnn], tr (I − k/k ) 0 0 [u1 II + u2 J + u3 (nnI + Inn) G−1 C − C = 0 3a1 + a2 (6.3b) +u4 (nn · J + J · nn) + u5 nnnn]. Being exact in the non-interaction approximation, the connections (6.3) have relatively simple form. In particular, • Tensors r and k enter the connections through their traces only – this is the only conductivity information needed for finding the entire set of transversely isotropic elastic constants. • Two resistivity related shape factors a1 and a2 enter (6.3) through one combination 3a1 + a2 only. Remark The orientation n is assumed to be known in the connections (6.3). Otherwise, if it is treated as an unknown parameter, (6.3) would not constitute a closed form cross-property connection. In the case of transversely isotropic fibers parallel to the x3 -axis (their symmetry axes coincide with the ones of spheroids), the effective resistivity is given by k/k0 − I = c [a1 (I − nn) + a2 nn] , where volume fraction c = 4πργ t /3 and the shape factors a1 and a2 are 1 1 1 a1 = 2 k11 , a2 = k33 − k0 k0 + k11 − k0 k0 .

(6.4)

(6.5)

The effective stiffness tensor is C − C0 =

$

N (m) = c

6 $

nk T (k)

k=1

with coefficients c1 (λ0 + 2G0 ) 4c2 G0 (λ0 + 2G0 ) , n2 = , c1 + λ0 + 2G0 4G0 (λ0 + 2G0 ) + c2 (λ0 + 3G0 ) −c3 (λ0 + 2G0 ) n3 = n4 = , c1 + λ0 + 2G0

n1 =

(6.6)

158

I. Sevostianov and M. Kachanov n5 =

8c5 G0 , 8G0 + c5

n6 =

2c6 (λ0 + 2G0 ) + 2 (c1 c6 − c3 c4 ) , 2 [λ0 + 2G0 + c1 ]

(6.7)

where

1 1 1 2 − (λ0 + G0 ) , c2 = 2 C1212 c1 = C1111 + C1122 − G0 , 1 1 1 c3 = c4 = C1133 − λ0 , c5 = 4 C1313 − G0 , c6 = C3333 − (λ0 + 2G0 ).

Expressing the volume fraction from (6.4), c=

tr(k0 r − I) , 2a1 + a2

(6.8)

and substituting it into (6.6) yields the following stiffness–conductivity connections: k11 + k22 + k33 n1 + n2 /2 0 C1111 − C1111 = 3− , 2a1 + a2 k0 n6 k11 + k22 + k33 0 C3333 − C3333 = 3− , 2a1 + a2 k0 k11 + k22 + k33 n1 − n2 /2 0 3− , C1122 − C1122 = 2a1 + a2 k0 k11 + k22 + k33 n3 0 3− , (6.9) C3311 − C3311 = 2a1 + a2 k0 n2 /2 k11 + k22 + k33 0 C1212 − C1212 = 3− , 2a1 + a2 k0 n5 /4 k11 + k22 + k33 0 = C3131 − C3131 3− . 2a1 + a2 k0 We now consider the case of isotropic parallel inhomogeneities (the x3 -direction coincides with n). Connections (6.3) reduce to: w1 + w2 [k0 (r11 + r22 + r33 ) − 3], 3a1 + a2 w1 + w2 + 2w3 + 2w4 + w5 [k0 (r11 + r22 + r33 ) − 3], E0 S3333 − 1 = 3a1 + a2 w1 [k0 (r11 + r22 + r33 ) − 3], E0 S1122 + ν0 = 3a1 + a2 w1 + w3 [k0 (r11 + r22 + r23 ) − 3], E0 S3311 + ν0 = E0 S2233 + ν0 = 3a1 + a2 E0 S1111 − 1 = E0 S2222 − 1 =

Connections between Elastic and Conductive Properties w2 /2 [k0 (r11 + r22 + r33 ) − 3], 3a1 + a2 w2 /2 + w4 /2 [k0 (r11 + r22 + r33 ) − 3]. E0 S1313 − 2 (1 + ν0 ) = 3a1 + a2

159

E0 S1212 − 2 (1 + ν0 ) =

(6.10a)

The stiffness–conductivity connections are: k11 + k22 + k33 , k0 k11 + k22 + k33 u1 + u2 + 2u3 + 2u4 + u5 3− , 3a1 + a2 k0 u1 k11 + k22 + k33 3− , 3a1 + a2 k0 k11 + k22 + k33 u1 + u3 3− , 3a1 + a2 k0 u2 /2 k11 + k22 + k33 3− , 3a1 + a2 k0 k11 + k22 + k33 u2 /2 + u4 /2 3− . (6.10b) 3a1 + a2 k0

0 0 C1111 − C1111 C2222 − C2222 u1 + u2 = = G0 G0 3a1 + a2 0 C3333 − C3333 = G0 0 C1122 − C1122 = G0 0 C3311 − C3311 = G0 0 C1212 − C1212 = G0 0 C3131 − C3131 = G0

3−

As shown in Section 6.2, these results can be extended to approximately parallel inhomogeneities without significant loss of accuracy. In the case of parallel cracks, treated as insulators, connections (6.10a) further reduce to the following form 2 1 − ν02 k0 − k33 E0 S3333 − 1 = , k33 2 1 − ν02 k0 − k33 2E0 S1313 − (1 + ν0 ) = . (6.11) 2 − ν0 k33 Remark An interesting observation is that the cross-property coefficient 2 1 − ν02 almost coincides with the corresponding one derived by Bristow (1960) (Eq. (2.3) for Young’s modulus) for the isotropic case of randomly oriented cracks; they differ by the factor (1 − 0.5v0 ) / (1 − 0.3v0 ). Moreover, as implied by results of Section 6, the same coefficient applies to the case of three mutually orthogonal crack families, with an arbitrary distribution of partial crack densities between them. This suggests the general hypothesis: the coefficient relating the Young’s modulus change in any direction to the

160


conductivity change in the same direction is close to 2 1 − v20 for any orientation distribution of cracks.

6.2. Moderate Orientation Scatter We assume now that inhomogeneities have some orientation scatter about direction n ≡ e3 . Such situations are common in applications. For example, in plastics reinforced by short parallel fibers, fiber orientations usually have some scatter; fatigue microcracks in metals are approximately parallel to the maximal tensile stress direction, etc. We show that moderate scatter does not substantially affect the accuracy of the results for parallel inhomogeneities, provided it is random (no bias towards either e1 or e2 so that the orientation distribution remains axisymmetric, overall). Indeed, (k) 3 is a linear combination of • Fourth-rank tensor = (1/V ) a nnnn the unperturbed term proportional e3 e3 e3 e3 , with the coefficient at this term 3 (k) and three terms due to scatter: somewhat smaller than ρ = (1/V ) a e1 e1 e1 e1 + e2 e2 e2 e2 ,

e1 e2 e1 e2 ,

e3 e3 (e1 e1 + e2 e2 ),

(6.12)

where the second term actually represents one of six similar terms and the third term represents one of twelve similar terms, due to symmetry with respect to all index rearrangements (since tensor is a sum of fully symmetric terms nnnn). 3 (k) is a linear combination of the unperturbed • Tensor ω = (1/V ) a nn term e3 e3 (with the coefficient somewhat smaller than ρ) and the term due to scatter e1 e1 + e2 e2 . (6.13) Denoting by φ the angle between e3 and n, we have n = cos φe3 + sin φ (cos βe1 + sin βe2 ), where the distribution over angle β is uniform if the scatter is random. The coefficients at the perturbed parts of the kth terms are proportional to sin2 φ, whereas coefficients at the unperturbed terms, e3 e3 e3 e3 and e3 e3 , are proportional to cos4 φ and cos2 φ, respectively. Hence, with the account of the number of terms involved and of the fact that < sin2 β cos2 β >β = 1/8, sin4 β >β = < cos4 β >β = 3/8, < sin2 β >β = < cos2 β >β = 1/2, the collective contribution of the perturbed terms, as estimated by the Euclidean norm, is much smaller than the one of the unperturbed terms. This results in two inequalities 7 (6.14) tan2 φ 3 + (3/8) tan4 φ 1, tan2 φ 0.730 for γ = 1 (spherical pores), and k/k0 > 0.714 for γ = 4. Combining expressions for factors A1−5 with the elasticity–conductivity connection, we relate the yield condition to the conductivities by expressing hˆ m in (b) 1.0

(a) 1.0

0.9

0.8

51.0

k1/k0

k3/k0

0.8 0.6

0.7

Isotropy

0.4 0.6 5 0.3 0.2 0.6

0.7

0.8 k1/k0

0.9

1.0

0.5 0.00

0.15 p

0.30

Fig. 9.3 (a) Possible combinations of principal conductivities k1 = k2 and k3 that correspond to aspect ratios 0.3 < γ < 4. (b) Range of functional dependencies of k1 on porosity p for transversely isotropic and isotropic cases.

232


terms of the effective conductivities k11 , k33 : k0 − k33 k0 − k11 hˆ 1 E0 = (2α1 + α2 + 2α3 + α4 ) + (α1 + α2 /2) , k11 k33 k0 − k33 k0 − k11 + α2 , hˆ 2 E0 = 2 (α2 + α4 ) k11 k33 k0 − k11 k0 − k33 + (α1 + α3 ) , hˆ 3 E0 = hˆ 4 E0 = (2α1 + α3 ) k11 k33 k0 − k11 k0 − k33 hˆ 5 E0 = 2 (2α2 + α4 ) + 2 (α2 + α4 ) , k11 k33 k0 − k11 k0 − k33 + (α1 + α2 + 2α3 + 2α4 ) , hˆ 6 E0 = 2 (α1 + α2 ) k11 k33

(9.12)

where factors α1−4 are given in Section 5, after Eq. (5.9a). Substituting them into (9.11) gives the main result of the present section – plastic yield factors A1−5 in terms of conductivities: k0 − k11 k0 − k33 k0 − k11 2 k0 − k33 2 + α12 + α13 + α14 A1 = α11 k11 k33 k11 k33 + α15

k0 − k11 k0 − k33 , k11 k33

k0 − k11 k0 − k33 + α22 + α23 A2 = 1 + α21 k11 k33 + α25

k0 − k11 k0 − k33 , k11 k33

k0 − k11 k0 − k33 + α32 + α33 A3 = α31 k11 k33 + α35

k0 − k11 k0 − k33 , k11 k33

k0 − k11 k0 − k33 + α42 + α43 A4 = α41 k11 k33 + α45

k0 − k11 k0 − k33 , k11 k33

k0 − k11 k0 − k33 + α52 + α53 A5 = α51 k11 k33 + α55

k0 − k11 k0 − k33 . k11 k33

k0 − k11 k11

k0 − k11 k11

k0 − k11 k11

k0 − k11 k11

2

+ α24

2

+ α34

2

+ α44

2

+ α54

k0 − k33 k33

k0 − k33 k33

k0 − k33 k33

k0 − k33 k33

2

2

2

2

(9.13)


233

Dimensionless coefficients αij (not to confuse with α1−4 ) do not depend on pore orientations or porosity, but they depend on pore aspect ratios (via α1−4 ). The sensitivity of αij to pore aspect ratios, in the range of 0.3 < γ < 4.0, is illustrated in Fig. 9.4. This figure assumes that all pores have identical aspect ratios (no shape scatter) – the situation when the sensitivity is maximal. 2

0.2

1 2

3

0.1

1 3

5 0.0

4

0

4 1

20.1

0

1

5

A1 2

3

4

21

2 0

1

1

A2

2

3

4 1

2

0.5

2 3

5 4

0

4

0 5

20.5 21

3 22

22 0

1

A3 2

1 3

4

24

4 0

1

2

3

21

1

A5

2

1

A4 2

3

4

1

Coefficient at (k0 2 k11)/k11

2

Coefficient at (k0 2 k33)/k33

3

Coefficient at (k0 2 k11)2/k211

4

Coefficient at (k0 2 k33)2/k233

5

Coefficient at (k0 2 k11)(k0 2 k33)/k11 k33

5 0

0

1

22

4

3

4

Fig. 9.4 Coefficients αij entering the plasticity–conductivity connection (3.4) as functions of pore aspect ratios (identical aspect ratios).

234


(a) 2

(b) 2

1

1

0

0

21 22 0.6

21

k3/k0 5 0.7 0.7

0.8

0.9

1.0

22 0.6

k3/k0 5 0.8 0.7

k1/k0

0.8

0.9

1.0

k1/k0

(c) 2 5 0.4 1 0 21 22 0.6

A1 A2 A3

k3/k0 5 0.9 0.7

0.8

0.9

A4 A5

1.0

k1/k0 Fig. 9.5 Plastic yield factors A1−5 as functions of conductivity k1 /k0 at several values of k3 /k0 . All pores have aspect ratio γ = 0.4.

The shape sensitivity of factors A1−5 is further illustrated in Figs. 9.5 and 9.6. They show the dependence of A1−5 on k11 /k0 at several fixed values of k33 /k0 , assuming identical aspect ratios (in the range of conductivities corresponding to relevant intervals of porosity and aspect ratios, Fig. 9.3). The curves of α1−4 for the oblate and prolate shapes are quite close. Thus, the shape sensitivity is low, even in the case of identical aspect ratios. It is even lower if scatter in aspect ratios is present, as discussed in Section 5.4.

9.4. Cases of Overall Isotropy In cases of overall isotropy (spherical pores or randomly oriented nonspherical ones), the yield condition reduces to the form 2τ ∗ = A1 (σkk )2 + A2 τij τji , 2

where the first term reflects sensitivity to the average hydrostatic stress.

(9.14)

Connections between Elastic and Conductive Properties (a) 2

(b) 2

1

1

0

0

21 22 0.6

21

k1/k0 5 0.7

0.7

0.8 k1/k0

0.9

1.0

22 0.6

235

k1/k0 5 0.8

0.7

0.8 k1/k0

0.9

1.0

(c) 2

1

5 3.0

0

21 22 0.6

k1/k0 5 0.9

0.7

0.8 k1/k0

0.9

1.0

A1

A4

A2

A5

A3

Fig. 9.6 Plastic yield factors A1−5 as functions of conductivity k1 /k0 at several values of k3 /k0 . All pores have aspect ratio γ = 3.

Of six coefficients hˆ m , only three, hˆ 1 , hˆ 2 , and hˆ 3 = hˆ 1 − hˆ 2 /2, enter equations for A1 , A2 , and they are given in terms of effective isotropic conductivity k as follows: E0 hˆ 1 = ς1 (k0 − k)/k, E0 hˆ 2 = ς2 (k0 − k)/k. The plastic yield factors in terms of k are 2 2 (1 − 2ν0 ) 1 k0 − k 2 k0 − k [6ς1 − ς2 ] (6ς1 − ς2 ) + , A1 = k k 3 (1 + ν0 )2 3 (1 + ν0 )2 k0 − k 2 1 ς2 , (9.15) A2 = 1 + 1 + ν0 k where ς1 , ς2 reflect the aspect ratio distribution and are given by ς1 = 3α1 + (3/2)α2 + 2α3 + α4 ,

ς2 = 3α2 + 2α4 .

(9.16)

Relations (9.15) are illustrated in Fig. 9.7 (identical aspect ratios are assumed). Equations (9.16) for ς1 , ς2 follows from results for the transversely isotropic case, in the special case of isotropy and hence they reflect the approximations involved in deriving the general elasticity–conductivity connection. However, the

236


40

4.0 5 0.3 5 1.0 5 4.0

3.0

30

A1

2.0

A2

20

10

1.0

0.0 0.5

5 0.3 5 1.0 5 4.0

0.6

0.7

0.8

0.9

1.0

0 0.5

0.6

0.7

k/k0

0.8

0.9

1.0

k/k0

Fig. 9.7 Case of overall isotropy. Plastic yield factors A1,2 as functions of conductivities, based on approximate relations (4.3) (identical pore aspect ratios).

case of isotropy can be analyzed independently, using the elasticity–conductivity connections (5.13). This would yield the same Eq. (9.15) but with different coefficients ς1 , ς2 , namely α 12q1 − 28q3 + 13q6 16q2 + 3q5 + = ; 2 E0 60q2 q5 120 q1 q6 − q3 β 4q1 + 4q3 + q6 32q2 + 11q5 + = , E0 30q2 q5 60 q1 q6 − q32

(9.17)

where coefficients qi are given by (4.36). These relations are illustrated in Fig. 9.8 (identical aspect ratios are assumed). Comparison of the last two figures shows that relations (9.17) have substantially lower sensitivity to pore aspect ratios. This indicates, again, that the approximations involved in deriving the general anisotropic plasticity–conductivity connection tend to exaggerate the sensitivity to pore shapes; the actual sensitivity is lower. We now consider Gaussian distribution of aspect ratios and examine the case when it has maximum at γ0 = 1 (sphere). Figure 9.9 compares the extreme case of parameter σ = 5 (almost uniform distribution over aspect ratios in the interval 0.3 < γ < 4) with the opposite case when the pores are exactly spherical (σ = 0);


237

20

1.5 5 0.3 5 1.0 5 4.0

5 0.3 5 1.0 5 4.0

15

1.0

A1

A2

10

0.5 5

0.0 0.5

0.6

0.7

0.8

0.9

0 0.5

1.0

0.6

0.7

k/k0

0.8

0.9

1.0

k/k0

Fig. 9.8 Case of overall isotropy. Plastic yield factors A1,2 as functions of conductivities, based on exact relations (4.4) (identical pore aspect ratios).

(a) 1.5

(b) 5

4 1.0 A1

A2 3

0.5 2

0.0 0.5

0.6

0.7

0.8

0.9

1.0

k/k0

1 0.5

0.6

0.7

0.8

0.9

1.0

k/k0 Normal distribution of shapes with 5 5

Spherical pores

Fig. 9.9 Case of overall isotropy. Plastic yield factors A1,2 as functions of conductivities. Comparison of the case of spherical pores with the case of normal distribution over pore aspect ratios, γ0 = 1 (sphere) being the maximum point.

238


for the latter case, (1 − ν0 )2 (1 − ν0 ) (1 − 2ν0 ) k0 − k + 2 k 3 (1 + ν0 ) 12 (1 + ν0 )2 5 (1 − ν0 ) k0 − k 2 . A2 = 1 + 7 − 5ν0 k

A1 =

k0 − k k

2 ,

(9.18)

The curves corresponding to the two cases are very close. This means that, as long as the maximum point of Gaussian distribution is γ0 = 1 (sphere), the effect of shape scatter is negligible. In such cases, therefore, no microscale information is needed at all, and plastic yield factors A1 , A2 can be taken from (9.18).

10. Conclusions We discuss connections between changes in the effective elastic and effective conductive properties due to the presence of various inhomogeneities (foreign particles, pores, cracks) in the otherwise continuous background material. Being free from any fitting parameters, the connections cover cases of overall anisotropy as well as cases of high property contrast between the inhomogeneities and the matrix. They can be used for estimating the difficult-to-measure properties (say, anisotropic elastic constants) from the data on another property (say, electric conductivities). They may also be useful for design of microstructures for the combined elastic– conductive performance (as in thermal barrier coatings) by identifying possible combinations of the two properties. These connections, developed by the present authors, are based on similarities between the microstructural parameters that control the effective elastic and effective conductive properties. The similarity leads to the cross-property connections. The fact that the parameters are not fully identical results in the approximate character of the connections. Connections derived in Section 5 assume that the constituents are isotropic so that the overall anisotropy is due solely to nonrandom orientations of inhomogeneities. The connections cover all orientation distributions in a unified way. In Section 6, we develop an alternative form of connections that applies to a certain – rather broad – class of orientation distributions: one, two or three families of approximately parallel inhomogeneities. In these cases, the alternative form has a higher accuracy than the general form. Its main advantage, however, is that it applies to materials with anisotropic constituents. An important observation is that, although the connections are derived under rather restrictive assumptions – spheroidal inhomogeneities in the non-interaction


239

approximation – they actually remain accurate under much broader conditions that include strongly interacting and irregularly shaped inhomogeneities. The reason is that, although the irregular shapes and the interactions may affect each of the properties separately, their effects on both properties are similar so that the connection between the two is not affected much. Moreover, replacing the non-interaction approximation by one of the commonly used approximate schemes (differential, self-consistent, etc.) does not necessarily improve the accuracy of the connection, as demonstrated on the example of metal foam (Section 7.1). Section 7 focuses on the experimental validation of the cross-property connections on several diverse materials: metal foams, short fiber-reinforced composites, microcracked metal, short fiber-reinforced composites with damage and plasma sprayed coatings. We find that, being free from fitting parameters, the connections hold with good accuracy, including cases of strong anisotropy and high property contrast between the phases. In Sections 8 and 9 we discuss the cross-property connections for two physical problems of different kind: (A) Contact of two rough surfaces pressed against each other, and (B) plastic yield of anisotropic porous metals in terms of effective conductivities. In contrast with the connections established in Sections 5 and 6 these results have not been experimentally tested, so far. Obviously, not all the physical properties can be linked to each other since they may be controlled by different microstructural parameters. In particular, the properties considered here – effective elasticity and effective conductivity – have relatively low sensitivity to clustering of inhomogeneities. Properties that are highly cluster sensitive, such as fracture-related quantities, cannot be linked, in a stable quantitative way, to cluster-insensitive ones (such as effective elasticity). This is discussed in Section 5.9. Appendix A

On Approximate Character of Elastic and Conductive Anisotropies

The usual definitions of elastic symmetry – assuming that symmetry elements are either present or not – may be overly restrictive for materials science applications considered in the present work. Anisotropies of the effective properties due to inhomogeneities usually have an approximate character due to various “irregularities” of microstructures. Moreover, some of the symmetries are intrinsically approximate, even in cases of ideally symmetric microstructures, approximate orthotropy of a solid with cracks being an example. The concept of approximate symmetry of the effective properties is used throughout the present work in an implicit way. Here, a quantitative approach to this issue is outlined, following Sevostianov and Kachanov (2008c).

240


We have to specify a norm that measures the difference between two sets of . Such a norm is dictated by needs of the specific elastic constants, Sijkl and Sijkl applications in mind. A physically reasonable choice of norm is provided by elastic potential in stresses f(σij ): the two sets are sufficiently close if f(σij ) is sufficiently well approximated by potential f (σij ), that is, the difference f σij − f σij = |(Sijkl − S )σij σkl | 2, k+l m=−∞ n=−∞ (βmn ) ∞ $

β¯ mn , m + n = 0, k + l > 2, k+l+1 m=−∞ n=−∞ (βmn )

(C.2)

(C.3)

where over bar means complex conjugate. Note that ηkl = 0 if k + l = 4n for the square array and k + l = 6n for the hexagonal array of fibers. Also, ηkl = 0 if k + l = 4n + 2 for the square array and k + l = 6n − 2 for the hexagonal array. All other components of these matrices vanish. The elements of the matrices of the infinite order rkl and gkl are defined as rkl =

∞ $ i=1

k+l+2 2 R η(k+1)(l+1) + ηkl . ηk(2i−1) η(2i−1)l , gkl = k l+1

R

4i−2

(C.4) Components of determinants (6.55) are given by 0 1 d ξ11 = C44 + C44 − fC44 − V1T Mp−1 V2 ,

ξ12 = e015 + e115 − fed15 − V˜ 1T Mp−1 V2 , ξ21 = e015 + e115 − fed15 − V1T Mp−1 V˜ 2 , 0 1 d −ξ22 = ζ11 + ζ11 − fζ11 − V˜ 1T Mp−1 V˜ 2 ,

(C.5)

where the vectors (V1 )s , (V˜ 1 )s , (V2 )t , (V˜ 2 )t , and matrix (Mp )ts of infinite order have block components defined as follows. For a square array of fibers: T d η1(4s−1) ed15 η1(4s−1) , (V1 )s = −R8s C44

Connections between Elastic and Conductive Properties (V˜ 1 )s = −R8s ed15 η1(4s−1)

d − ζ11 η1(4s−1)

d η(4t−1)1 (V2 )t = − C44

ed15 η(4t−1)1

(V˜ 2 )s = − ed15 η(4t−1)1

d − ζ11 η(4t−1)1

T ,

T , T ,

⎡

⎤ δts e015 + e115 − b˜r(4t−1)(4s−1) ⎦, 0 1 + d r˜ −δts ζ11 + ζ11 (4t−1)(4s−1)

0 1 − a˜r δts C44 + C44 (4t−1)(4s−1) (Mp )ts = ⎣ 0 1 δts e15 + e15 − c˜r (4t−1)(4s−1) r˜i j = R2j+2

∞ $

245

R8m ηi(4m+1) η(4m+1)j .

(C.6)

m=1

For a hexagonal array: d (V1 )s = −R12s C44 η1(6s−1) (V˜ 1 )s = −R12s ed15 η1(6s−1)

ed15 η1(6s−1)

T ,

d − ζ11 η1(6s−1)

ed15 η(6t−1)1

(V˜ 2 )s = − ed15 η(6t−1)1

d − ζ11 η(6t−1)1

, T ,

⎡

0 1 − a˜r δts C44 + C44 (6t−1)(6s−1) (Mp )ts = ⎣ 0 δts e15 + e115 − c˜r (6t−1)(6s−1) ∞ $

,

T

d η(6t−1)1 (V2 )t = − C44

r˜i j = R2j+2

T

R12m ηi(6m+1) η(6m+1)j ,

⎤ δts e015 + e115 − b˜r(6t−1)(6s−1) 0 ⎦, 1 + d r˜ −δts ζ11 + ζ11 (6t−1)(6s−1)

(C.7)

m=1

where the following notations are used: , 2 -C 0 1 d 0 1 d d 0 1 1 0 a = ζ11 + ζ11 C44 + e15 + e15 e15 C44 − 2 C44 e15 + C44 e15 ed15 e, b= c=

,

,

e015 + e115

e015 + e115

ed15 ed15

2

-C 0 1 d 0 1 1 0 d + ζ11 + ζ11 − 2 C44 e15 + C44 e15 ζ11 e, ed15 C44

2

-C 0 1 d 0 1 d + C44 + C44 − 2 e115 ζ11 + e115 ζ11 e, ed15 ζ11 C44

246 d=

I. Sevostianov and M. Kachanov ,

0 1 + C44 C44

d ζ11

2

-C d 0 0 + e015 + e115 ed15 ζ11 + 2 e115 ζ11 + e015 ζ11 e, ed15

2 0 1 0 1 ζ11 + e015 + e115 . + C44 + ζ11 e = C44

(C.8)

Acknowledgment The authors are grateful to J. Berryman, V. Levin, G. Milton, and R. Zimmerman for a number of valuable remarks. The authors acknowledge current support of the National Science Foundation, through a grant to Tufts University and of NASA, through a grant to New Mexico State University. This research has also been supported, in the past, by NSF, DOE, NASA, AFOSR, Sandia National Labs, General Electric, and Alstom Power.

References Arts, R. J., Rasolofosaon, P. N. J., and Zinsner, B. E. (1996). Experimental and theoretical tools for characterizing anisotropy due to mechanical defects in rocks under varying pore and confining pressures. In Seismic Anisotropy (S. E. Fjaer, Ed.), pp. 384–432. Society of Exploration Geophysicists, Tulsa, Oklahoma. Avellaneda, M., and Swart, P. J. (1998). Calculating the performance of 1-3 piezoelectric composites for hydrophone applications: an effective medium approach. J. Acoust. Soc. Am. 103, 1449–1467. Barber, J. R. (2003). Bounds on the electrical resistance between contacting elastic rough bodies. Proc. R. Soc. Lond. A 459, 53–66. Batchelor, G. K., and O’Brien, R. W. (1977). Thermal and electrical conduction through a granular material. Proc. R. Soc. Lond. A 355, 313–333. Benveniste, Y. (1986). On the Mori-Tanaka method for cracked solids. Mech. Res. Comm. 13(4), 193–201. Benveniste, Y. (1992). The determination of the elastic and electric fields in a piezoelectric inhomogeneity. J. Appl. Phys. 72, 1086–1095. Benveniste, Y., and Dvorak, G. J. (1992). Uniform fields and universal relations in piezoelectric composites. J. Mech. Phys. Solids. 40, 1295–1312. Beran, M. J. (1968). Statistical Continuum Theories. Wiley, New York. Beran, M. J. (1965). Use of the variational approach to determine bounds for the effective permittivity in random media. Nuovo Cimento 38, 771–782. Beran, M. J., and Molyneux, J. (1966). Use of classical variational principles to determine bounds for the effective bulk modulus in heterogeneous media. Q. Appl. Math. 24, 107–118. Bergman, D. J. (1978). The dielectric constant of a composite material – a problem in classical physics. Phys. Rep. C 43, 377–407. Berryman, J. G. (1980a). Long-wavelength propagation in composite elastic media I. Spherical inclusions. J. Acoust. Soc. Am. 68, 1809–1819. Berryman, J. G. (1980a). Long-wavelength propagation in composite elastic media II. Ellipsoidal inclusions. J. Acoust. Soc. Am. 68, 1820–1831. Berryman, J. G. (1982). Effective medium theory for elastic composites. In Elastic Wave Scattering and Propagation (V. K. Varadan, and V. V. Varadan, Eds.), pp. 111–129. Ann Arbor Science.


247

Berryman, J. G., and Milton, G. W. (1988). Microgeometry of random composites and porous media. J. Phys. D 21, 87–94. Bravo-Castillero, J., Guinovart-Diaz, R., Sabina, F. J., and Rodriguez-Ramos, R. (2001b). Closed-form expressions for the effective coefficients of a fiber-reinforced composite with transversely-isotropic constituents – II. Piezoelectric and square symmetry. Mech. Mater. 33, 237–248. Bristow, J. R. (1960). Microcracks, and the static and dynamic elastic constants of annealed heavily cold-worked metals. Br. J. Appl. Phys. 11, 81–85. Brown, S., and Scholz, C. (1985). Closure of random elastic surfaces in contact. J. Geophys. Res. 90, 5531–5545. Bruggeman, D. A. G. (1935). Berechnung verschiedener physikalisher Konstanten von heterogenen Substanzen. I. Dielectrizitätkonstanten und Leitfähigkeiten der Mischkörper aus isotropen Substanzen. Ann. Phys. Leipzig 24, 636–679. Bruggeman, D. A. G. (1937). Berechnung verschiedener physikalisher Konstanten von heterogenen Substanzen. III. Die elastische Konstanten der Quaiisotropen Mischkörper aus isotropen Substanzen. Ann. Phys. Leipzig 29, 160–178. Chan, H. L. W., and Unsworth, J. (1989). Simple model for piezoelectric ceramic/polymer 1-3 composites used in ultrasonic transducer applications. IEEE T. Ultrason. Ferr. 36, 434–441. Chen, F. C., and Young, K. (1977). Inclusions of arbitrary shape in an elastic medium. J. Math. Phys. 18, 1412–1416. Cherkaev, A. V. (2000). Variational Methods for Structural Optimization. Springer. Cherkaev,A. V., and Gibiansky, L. V. (1992). The exact coupled bounds for effective tensors of electrical and magnetic properties of two-component two-dimensional composites. Proc. Roy. Soc. Edinb. A 122, 93–125. Choy, C. L., Leung, W. P., Kowk, K. W., and Lau, F. P. (1992). Elastic moduli and thermal conductivity of injection-molded short fiber reinforced thermoplastics. Polym. Comp. 13, 69–80. Dunn, M. L. (1993). Exact relations between the thermoelectroelastic moduli of heterogeneous materials. Proc. R. Soc. Lond. A 441, 549–557. Eshelby, J. D. (1957). The determination of the elastic field on an ellipsoidal inclusion and related problems. Proc. R. Soc. Lond. A 241, 376–392. Eshelby, J. D. (1961). Elastic inclusions and inhomogeneities. In: Progress in Solid Mechanics, vol. 2 (I. N. Sneddon, and R. Hill, Eds.), pp. 89–140. North-Holland, Amsterdam. Fabrikant, V. (1987). The stress intensity factor for an external elliptical crack. Int. J. Solids Struct. 23, 465–467. Fatemi, A., and Yang, L. (1998). Cumulative fatigue damage and life prediction theories: a survey of the state of the art for homogeneous materials. Int. J. Fatigue 20, 9–34. Fedorov, F. I. (1968). Theory of Elastic Waves in Crystals. Plenum Press, New York. Gibiansky, L. V., and Torquato, S. (1993). Link between the conductivity and elastic moduli of composite materials. Phys. Rev. Lett. 71, 2927–2930. Gibiansky, L. V., and Torquato, S. (1995). Rigorous link between the conductivity and elastic moduli of fiber reinforced materials. Philos. Trans. R. Soc. Lond. A 353, 243–278. Gibiansky, L. V., and Torquato, S. (1996a). Connection between the conductivity and bulk modulus of isotropic composite materials. Proc. R. Soc. Lond. A 452, 253–283. Gibiansky, L. V., and Torquato, S. (1996b). Bounds on the effective moduli of cracked materials. J. Mech. Phys. Solids 44, 233–242. Gibiansky, L. V., and Torquato, S. (1998). Rigorous connection between physical properties of porous rock. J. Geophys. Res. 103, 23911–23923. Gorbatikh, L. (2004). On elastic compliances of interfacial cracks. Int. J. Fract. 127, L141–L148. Goryacheva, I. G. (1998). Contact Mechanics in Tribology. Kluwer Academic Publishers. Grechka, V., and Kachanov, M. (2006a). Seismic characterization of multiple fracture sets: does orthotropy suffice? Geophys. 71, D935–D105.

248


Grechka, V., and Kachanov, M. (2006b). Effective elasticity of rocks with closely spaced and intersecting cracks. Geophys. 71, D85–D91. Grechka, V., Vasconselos, I., and Kachanov, M. (2006). The influence of crack shapes on the effective elasticity of fractured rocks. Geophys. 71, D153–D160. Grigolyuk, E. I., and Fil’shtinskii, L. A. (1970). Perforated Plates and Shells. Nauka, Moscow. (in Russian). Greenwood, J. A. (1966). Constriction resistance and the real area of contact. Br. J. Appl. Phys. 17, 1621–1632. Guinovart-Diaz, R., Bravo-Castillero, J., Rodriguez-Ramos, R., and Sabina, F. J. (2001). Closed-form expressions for the effective coefficients of a fiber-reinforced composite with transversely-isotropic constituents – I. Elastic and hexagonal symmetry. J. Mech. Phys. Solids 49, 1445–1462. Hashin, Z. (1983). Analysis of composite materials – a survey. J. Appl. Mech. 50, 481–505. Hashin, Z., and Shtrikman, S. (1963). A variational approach to the theory of the elastic behavior of multiphase materials. J. Mech. Phys. Solids 11, 127–140. Hill, R. (1963). Elastic properties of reinforced solids: some theoretical principles. J. Mech. Phys. Solids 11, 357–372. Hill, R. (1964). Theory of mechanical properties of fibre-strengthened materials: I. Elastic behaviour. J. Mech. Phys. Solids 12, 199–212. Hill, R. (1965). A self-consistent mechanics of composite materials. J. Mech. Phys. Solids 11, 357–372. Hill, R. and Storakers, B. (1990). A concise treatment of axisymmetric indentation in elasticity. In: Elasticity: Mathematical Methods and Applications (G. Eason, R. W. Ogden, Eds.), 199–211. Ellis Horwood Ltd, Chichester. Holm, R. (1929). Uber metallische Kontaktwiderstände. Wiss. Verbff. Siemens- Werken 7, 217–258. Jaeger, J. C., Cook, N. G. W., and Zimmerman, R. W. (2007). Fundamentals of Rock Mechanics. Blackwell Publ. Johannesson, B., and Pedersen, O. B. (1998). Analytical determination of the average Eshelby tensor for transversely isotropic fiber orientation distributions. Acta. Mater. 46, 3165–3173. Johnson, K. L. (1985). Contact Mechanics. Cambridge University Press. Kachanov, M. (1980). Continuum model of medium with cracks. J. Eng. Mech. Div. ASCE 106, 1039–1051. Kachanov, M. (1994). On the concept of damage in creep and in the brittle-elastic range. Int J Damage Mech. 3, 329–337. Kachanov, M. (1993). Elastic solids with many cracks and related problems. In Advances in Applied Mechanics, vol. 30 (J. Hutchinson, and T. Wu, Eds.), pp. 256–426. Academic Press. Kachanov, M. (1995). On the concept of approximate elastic symmetry and applications to materials with defects. Int. J. Fract. 74, R33–R38. Kachanov, M., and Sevostianov, I. (2005). On quantitative characterization of microstructures and effective properties. Int. J. Solids Struct. 42, 309–336. Kachanov, M., and Shafiro, B. (1997). Materials with fluid-filled pores of various shapes: effective elastic properties and fluid pressure polarization. Int. J. Solids Struct. 34, 3517–3540. Kachanov, M., Sevostianov, I., and Shafiro, B. (2001). Explicit cross-property correlations for porous materials with anisotropic microstructures. J. Mech. Phys. Solids 49, 1–25. Kachanov, M., Tsukrov, I., and Shafiro, B. (1994). Effective moduli of solids with cavities of various shapes. Appl. Mech. Rev. 47(1), S151–S174. Kanaun, S. K., and Levin, V. M. (1994). The self-consistent field method in mechanics of matrix composite materials. In Advances in Mathematical Modeling of Composite Materials, (K. Z. Markov Ed.), pp. 1–58. World Scientific Publ., Singapore. Kanaun, S. K. and Levin, V. M. (2008). Self-Consistent Methods for Composites, Springer. Kantor, Y., and Bergman, D. J. (1984). Improved rigorous bounds on the effective elastic moduli of a composite material. J. Mech. Phys. Solids 32, 41–62. Kassir, M. K., and Sih, G. (1975). Three-Dimensional Crack Problems. Noordhoff, Leyden (Chapter 4).


249

Kim, A., Hasan, M. A. Nahm, S. H., and Cho, S. S. (2005). Evaluation of compressive mechanical properties of Al-foams using electrical conductivity. Compos. Struct. 71, 191–198. Kee, A., Matic, P., and Everett, R. K. (1998). A mesoscale computer simulation of multiaxial yield in gasar porous copper. Mater. Sci. Eng. A 249, 30–39. Korn, G. A., and Korn, T. M. (1968). Mathematical Handbook for Scientists and Engineers. McGraw Hill, New York (Chapter 21). Kröner, E. (1958). Berechnung der elastischen Konstanten des Vielkristalls aus den Konstanten des Einkristalls. Z. Phys. 151, 504–518. Kudinov, V. V. (1977). Plasma Sprayed Coatings. Nauka, Moscow (in Russian). Kunin, I. A. (1983). Elastic Media with Microstructure. Springer Verlag, Berlin. Lamb, H. (1932). Hydrodynamics. Cambridge University Press. Laraia, V. J., Rus, J. L., and Heuer, A. H. (1995). Microstructural shape factors: relation of random planar sections to three-dimensional microstructures. J. Am. Ceram. Soc. 78, 1532–1536. Levin, V. M. (1967). On the coefficients of thermal expansion of heterogeneous material. Mech. Solids 2, 58–61. (English transl. of Izvestia AN SSSR, Mekhanika Tverdogo Tela). Levin, V., Michelitsch, T., and Sevostianov, I. (2000). Spheroidal inhomogeneity in the transversely isotropic piezoelectric medium. Arch. Appl. Mech. 70, 673–693. Lurie, K. A., and Cherkaev, A. V. (1982). Accurate estimates of the conductivity of mixtures formed of two materials in a given proportion (two-dimensional problem). Soviet Phys. Dokl. 27, 461–462. Lurie, K. A., and Cherkaev, A. V. (1984). Exact estimates of conductivity of composites formed by two isotropically conducting media taken in prescribed proportion. Proc. R. Soc. Edinb. A 104, 21–38. Lutz, M. P., and Zimmerman, R. W. (2005). Effect of inhomogeneous interphase zone on the elastic and thermal properties of a particulate composite. Int. J. Solids Struct. 42, 429–437. Mackenzie, J. K. (1950). The elastic constants of a solid containing spherical holes. Proc. R. Soc. Lond. 63B, 2–11. Markov, K. Z. (2000). Elementary micromechanics of heterogeneous media. In Heterogeneous Media: Micromechanics Modeling Methods and Simulations (K. Z. Markov, and L. Preziozi, Eds.), pp. 1–162. Birkhauser, Boston. McCoy, J. J. (1970). On the displacement field in an elastic medium with random variation of material properties. In Proceedings of the 6-th Annual Meeting of the Society of Engineering Science (A. C. Eringen, Ed.), pp. 235–254. Gordon and Breach, New York. McLaughlin, R. (1977). A study of the differential scheme for composite materials. Int. J. Eng. Sci. 15, 237–244. Mear, M., Sevostianov, I., and Kachanov, M. (2007). Elastic compliances of non-flat cracks. Int. J. Solids Struct. 44, 6412–6427. Mindlin, R. D. (1949). Compliance of elastic bodies in contact. Trans. ASME Ser. E. J. Appl. Mech. 16, 259–266. Milgrom, M., and Shtrikman, S. (1989). Linear response of two-phase composites with cross moduli: exact universal relations. Phys Rev. A 40, 1568–1575. Milton, G. W. (1984). Correlation of the electromagnetic and elastic properties of composites and microgeometries corresponding with effective medium theory. In Physics and Chemistry of Porous Media: Papers from a Symposium Held at Schlumberger-Doll Research, Oct. 24-25, 1983 (D. L. Johnson, and P. N. Sen, Eds.), pp. 66–77. American Institute of Physics, Woodbury, NY. Milton, G. W. (1990). A brief review of the translation method for bounding effective elastic tensors of composites. In Continuum Models and Discrete Systems -6 (G. A. Maugin, Ed.), pp. 60–74. Longman Scientific and Technical. Milton, G. W. (1997). Composites: a myriad of microstructure independent relations. In Theoretical and Applied Mechanics 1996 (T., Tatsumi, Ed.), pp. 443–459. Elsevier. Milton, G. W. (2002). The Theory of Composites. Cambridge University Press. Milton, G. W., and Phan-Thien, N. (1982). New bounds on effective elastic moduli of twocomponent materials. Proc. R. Soc. Lond. A 380, 305–331.

250


Mori, T., and Tanaka, K. (1973). Average stress in matrix and average elastic energy of materials with misfitting inclusions. Acta Metall. Mater. 21, 571–574. Mura, T. (1987). Micromechanics of Defects in Solids. Martinus Nijhoff Publ., Dordrecht. Murakami, Y. (Ed.) (1987). Stress Intensity Factors Handbook, vol. 2. Pergamon. Murat, F., and Tartar, L. (1985). Calculs des variations et homogénízation. In Les methods de l’homogenization: théorie et applications en physique, pp. 319–369. Eyrolles, Paris: English translation: Calculus of variation and homogenization. In Topics in the Mathematical Modeling of Composite Materials (A. Cherkaev, and R. Kohn, Eds.), pp 139–173. Birkhäuser, Boston. Nagy, P. B. (1992). Ultrasonic classification of imperfect interfaces. J.Nondestr. Eval. 11, 127–139. van der Pauw, L. J. (1958). A method for measuring specific resistivity and Hall effect of discs of arbitrary shape. Philips Tech. Rev. 20, 220–224. Piau, M. (1980). Crack-induced anisotropy and scattering in stressed rocks. Int. J. Eng. Sci. 18, 549–568. Prager, S. (1969). Improved variational bounds on some bulk properties of a two-phase random media. J. Chem. Phys. 50, 4305–4312. Pyrak-Nolte, L. J., and Morris, J. P. (2000). The relation between fracture stiffness and fluid flow. Int. J. Rock. Mech. Min. 37, 245–262. Pyrak-Nolte, L. J., Myer, L. R., Cook, N. G. W., and Witherspoon, P. A. (1987). Hydraulic and mechanical properties of natural fractures in low permeability rock. In Proceedings of the 6th International Congress on Rock Mechanics (G. Herget, and S. Vongpaisal, Eds.), pp. 225–231. Balkema, Rotterdam. Rice, J. R. (1975). Continuum mechanics and thermodynamics of plasticity in relation to microscale deformation mechanisms. In Constitutive Equations in Plasticity (A. Argon, Eds.), MIT Press. Rosen, B. W., and Hashin, Z. (1970). Effective thermal expansion coefficients and specific heats of composite materials. Int. J. Eng. Sci. 8, 157–173. Rodin, G. J. (1996). Eshelby’s inclusion problem for polygons and polyhedra. J. Mech. Phys. Solids 44, 1977–1995. Rodriguez-Ramos, R., Sabina, F. J., Guinovart-Diaz, R., and Bravo-Castillero, J. (2001). Closed-form expressions for the effective coefficients of a fiber-reinforced composite with transversely-isotropic constituents – I. Elastic and square symmetry. Mech. Mater. 33, 223–235. Sabina, F. J., Rodriguez-Ramos, R., Bravo-Castillero, J., and Guinovart-Diaz, R. (2001). Closed-form expressions for the effective coefficients of a fiber-reinforced composite with transversely-isotropic constituents – II. Piezoelectric and hexagonal symmetry. J. Mech. Phys. Solids 49, 1463–1479. Sack, R. A. (1946). Extension of Griffith’s theory of rupture to three dimensions. Proc. Phys. Soc. 58, 729–736. Schulgasser, K. (1992). Relationship between the effective properties of transversely isotropic piezoelectric composites. J. Mech. Phys. Solids 40, 473–479. Segedin, C. M. (1950). Note on a penny-shaped crack under shear. Proc. Camb. Philol. Soc. 47, 396–400. Sevostianov, I. (2003). Explicit relations between elastic and conductive properties of a material containing annular cracks. Philos. Trans. R. Soc. Lond. A 361, 987–999. Sevostianov, I., and Kachanov, M. (2000). Modeling of the anisotropic elastic properties of plasmasprayed coatings in relation to their microstructure. Acta. Mater. 48, 1361–1370. Sevostianov, I., and Kachanov, M. (2001). On the yield condition for anisotropic porous materials. Mater. Sci. Eng. A 313, 1–15. Sevostianov, I., and Kachanov, M. (2002a). Explicit cross-property correlations for anisotropic twophase composite materials J. Mech. Phys. Solids 50, 253–282. Sevostianov, I., and Kachanov, M. (2002b). On the elastic compliances of irregularly shaped cracks. Int. J. Fract. 114, 245–257. Sevostianov, I., and Kachanov, M. (2003). Correlations between elastic moduli and thermal conductivities of anisotropic short fiber reinforced thermoplastics: theory and experimental verification. Mater. Sci. Eng. A 360, 339–344.


251

Sevostianov, I., and Kachanov, M. (2004). Connection between elastic and conductive properties of microstructures with Hertzian contacts. Proc. R. Soc. Lond. A 460, 1529–1534. Sevostianov, I., and Kachanov, M. (2006). Plastic yield surfaces of anisotropic porous materials in terms of electric conductivities. Mech. Mater. 38, 908–923. Sevostianov, I., and Kachanov, M. (2008a). Contact of rough surfaces: a simple model for elasticity, conductivity and cross-property connections. J. Mech. Phys. Solids 56, 1380–1400. Sevostianov, I., and Kachanov, M. (2008b). Normal and tangential compliances of interface of rough surfaces with contacts of elliptic shape. Int. J. Solids Struct. 45, 2723–2736. Sevostianov, I., and Kachanov, M. (2008c). On approximate elastic symmetries and elliptic orthotropy, International Journal of Engineering Sciences 46(2008), 211–223. Sevostianov, I., and Sabina, F. (2007). Cross-property connections for fiber reinforced piezoelectric materials. Int. J. Eng. Sci. 45, 719–735. Sevostianov, I., Bogarapu, M., and Tabakov, P. (2002a). Correlation between elastic and electric properties for cyclically loaded metals. Int. J. Fract. 115, L15–L20. Sevostianov, I., Levin, V., and Kachanov, M. (2001). On the modeling and design of piezocomposites with prescribed properties. Arch. Appl. Mech. 71, 733–747. Sevostianov, I., Kachanov, M., and Ruud, J. (2002). On the elastic properties of PVD coatings in relation to their microstructure. ASME J. Eng. Mater. Technol. 124, 246–249. Sevostianov, I., Kachanov, M., Ruud, J., Lorraine, P., and Dubois, M. (2004). Quantitative characterization of microstructures of plasma-sprayed coatings and their conductive and elastic properties. Mater. Sci. Eng. A386, 164–174. Sevostianov, I., Kovácik, J., and Simancík, F. (2002b). Cross-property correlation for metal foams: theory and experiment. Int. J. Fract. 114, L23–L28. Sevostianov, I., Kovácik, J., and Simancík, F. (2006a). Elastic and electric properties of closed-cell aluminum foams. Cross-property connection Mater. Sci. Eng. A 420, 87–99. Sevostianov, I., Sabina, F. J., Bravo-Castillero, J., Guinovart-Diaz, R., and Rodriguez-Ramos, R. (2006). Cross-property connections for fiber-reinforced composites with transverselyisotropic constituents. Int. J. Fract. 142, 299–306. Sevostianov, I., Verijenko, V. E., and Kachanov, M. (2002). Cross-property correlations for short fiber reinforced composites with damage and their experimental verification. Comp. B 33, 205–213. Sevostianov, I., Verijenko, V., and Verijenko, B. (2003). Evaluation of microstructure and properties deterioration in short fiber reinforced thermoplastics subjected to hydrothermal aging. Comp. Struct. 62, 411–417. da Silva, M. G., and Ramesh, K. T. (1997). The rate-dependent deformation and localization of fully dense and porous Ti-6Al-4V. Mater. Sci. Eng. A 232, 11–22. Smith, W. A. (1993). Modeling 1-3 composite piezoelectrics: hydrostatic response. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 40, 41–49. Smith, W. A., and Auld, B. A. (1991). Modeling 1-3 composite piezoelectrics: thicknessmode oscillations. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 38, 40–47. Tartar, L. (1979). Estimation de coefficients homogénéisés In Computing Methods in Applied Sciences and Engineering (R., Glowinski, and J.-L., Lions, Eds.), pp. 364–373, Springer-Verlag, Berlin. English translation: Estimation of homogenization coefficients. In Topics in the Mathematical Modeling of Composite Materials (A. Cherkaev, and R. Kohn, Eds.), pp. 9–20. Birkhäuser, Boston. Taya, M., and Chou, T.-W. (1981). On two kinds of ellipsoidal inhomogeneities in an infinite elastic body: an application to a hybrid composite. Int. J. Solids Struct. 17, 553–563. Torquato, S. (1992). Connection between the morphology and effective properties of heterogeneous materials. In Macroscopic Behavior of Heterogeneous Materials from Microstructure: Presented at the Winter Annual Meeting of the American Society of Mechanical Engineers, Anaheim, California, November 8-13 (S. Torquato, and D. Krajcinovic, Eds.), pp. 53–65. ASME, New York. Torquato, S., Gibiansky, L. V., Silva, M. J., and Gibson, L. J. (1998). Effective mechanical and transport properties of cellular solids. Int. J. Mech. Sci. 40, 71–82.

252


Torquato, S. (2002). Random Heterogeneous Materials: Microstructure and Macroscopic Properties. Springer. Torquato, S., Donev, A., Evans, A. G., and Brinker, C. J. (2005). Manufacturable extremal lowdielectric, high-stiffness porous material. J. Appl. Phys. 97, 124103–124107. Vavakin, A. S., and Salganik, R. L. (1975). Effective characteristics of nonhomogeneous media with isolated inhomogeneities. Mech. Solids 10, 65–75. (English transl. of Izvestia AN SSSR, Mekhanika Tverdogo Tela). Walpole, L. J. (1969). On the overall elastic moduli of composite materials. J. Mech. Phys. Solids 17, 235–251. Walpole, L. J. (1984). Fourth-rank tensors of the thirty-two crystal classes: multiplication tables. Proc. R. Soc. Lond.A 391, 149–179. Wang, Z. C., Davies, T. J., Ridley, N., and Ogwu, A. A. (1996). Superplasticity of ceramic materials – II. Effect of initial porosity and doping on the superplastic behavior of alumina. Acta. Mater. 44, 4301–4309. Wittke, W. (1990). Rock Mechanics. Springer Verlag. Wu, T. T. (1966). The effect of inclusion shape on the elastic moduli of a two-phase material. Int. J. Solids Struct. 2, 1–8. Yovanovich, M. M., and Marotta, E. E. (2003). Thermal spreading and contact resistances. In Heat Transfer Handbook (A., Bejan, and A. D., Krauf, Eds.), pp. 261–393. John Wiley. Zamora, M., Dung, V. T., Bienfait, G., and Poirier, J. P. (1993). An empirical relationship between thermal-conductivity and elastic wave velocities in sandstone. Geophys. Res. Lett. 20, 1679–1682. Zimmerman, R. W. (1991). Elastic moduli of a solid containing spherical inclusions. Mech. Mater. 12, 17–24. Zimmerman, R. W. (1996). Effective conductivity of a two-dimensional medium containing elliptical inhomogeneities. Proc. R. Soc. Lond. A 453, 1713–1727. Zhao, H. F., Hu, G. K., and Lu, T. J. (2004). Correlation between the elastic moduli and conductivity of two-dimensional isotropic two-phase composites. Int. J. Fract. 126, L11–L18. Zohdi, T., and Kachanov, M. (2005). A note on the micromechanics of plastic yield of porous solids. Int. J. Fract. 133, L31–35. Zohdi, T., Kachanov, M., and Sevostianov, I. (2002). A microscale numerical analysis of a plastic flow in a porous material. Int. J. Plasticity 18, 1649–1659.

Coarse Graining in Elasto-viscoplasticity: Bridging the Gap from Microscopic Fluctuations to Dissipation MARKUS HÜTTERa and THEO A. TERVOORTb a Polymer Physics, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10,

CH-8093 Zurich, Switzerland. Email: [email protected] b Polymer Technology, Department of Materials, ETH Zurich, Wolfgang-Pauli-Str. 10,

CH-8093 Zurich, Switzerland. Email: [email protected]

Abstract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 2. GENERIC Framework of Nonequilibrium Thermodynamics. I. Fundamentals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2. Choice of Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3. Two-generator Idea, Separation of Reversible and Irreversible Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4. Full Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

259 259 259 259 260

3. Applications of the GENERIC Formalism . . . . . . . . . . . . . . . . . . . . . . . . . 3.1. Hamiltonian Point Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2. Single Particle in Spring Potential with Linear Drag Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3. Nonisothermal Hydrodynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4. Macroscopic Elasticity and Elasto-viscoplasticity . . . . . . . . . . . . . .

263 263 264 266 271

4. GENERIC Framework. II. Methodology of Coarse Graining . . . . . . . . . 4.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2. Ensembles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3. Generators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4. Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

279 279 281 283 284

5. Applications of the Coarse-graining Procedure . . . . . . . . . . . . . . . . . . . . . 288 5.1. From Hamiltonian Point Mechanics to Hydrodynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 5.2. From Hamiltonian Point Mechanics to Elasto-viscoplasticity . . . . 291 6. Discussion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 Appendix A. Calculations Related to Hydrodynamics (Section 3.3) . . . . . . . 312 ˆ

Appendix B. Derivation of L(Fαβ ,uγ ) (r, r ) in Eq. (5.12) . . . . . . . . . . . . . . . . 313 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314

ADVANCES IN APPLIED MECHANICS, VOL. 42 ISSN: 0065-2156 DOI: 10.1016/S0065-2156(08)00003-3

253


254

M. Hütter and T. A. Tervoort

Abstract The interrelation between the elasto-viscoplastic behavior of anisotropic solids on the macroscopic scale and the microscopic dynamics of their constituent atoms and molecules is examined. To that end, we employ a scheme for coarse graining as used in the context of the general equation for the nonequilibrium reversible–irreversible coupling (GENERIC) framework. First, the framework is introduced and illustrated with several examples that are self-contained on a single level of description, that is, that do not establish any links to other levels of description. Second, as a prototype example of applying the coarse graining scheme, the derivation of the evolution equations for nonisothermal hydrodynamics based on the microscopic Hamiltonian point mechanics is illustrated, leading to the well-known Navier–Stokes equation and the balance equations for mass and energy. Third, in the main part, we elaborate in detail on the application of the same methodology of coarse graining to elasto-viscoplastic solids. On the macroscopic scale, the elastic part of the deformation gradient is used as an internal variable to describe the state of deformation. Viscoplasticity then follows from relaxation of the elastic deformation gradient and is conveniently expressed in terms of so-called plastic velocity gradient tensor. Typically, constitutive relations for the plastic velocity gradient tensor rely on phenomenological macroscopic arguments, resulting in a large number of material constants. In this work, we illustrate a procedure to relate the plastic velocity gradient tensor to the rapid microscopic fluctuations of the elastic deformation gradient. In this way, we are able to use microscopic information about anisotropic solids to restrict the tensorial structure of the plastic velocity gradient tensor, thereby drastically reducing the number of material parameters. The antisymmetric part of the plastic velocity gradient tensor, the so-called plastic spin, naturally arises in our treatment and does not require any special constitutive assumptions.

Table List of frequently used symbols

Symbol

Meaning

A, B, C A α , Bα Aαβ , Bαβ B Be C cijkl dc , dˆ c

Arbitrary functional of x Arbitrary vectors Arbitrary tensors Total left Cauchy–Green strain tensor, B = F · FT Elastic left Cauchy–Green strain tensor, Be = Fe · Fe,T Total right Cauchy–Green strain tensor, C = FT · F Correlations of wij , see Eq. (5.26)

i dir ,

E E0 e

j

dˆ jr

Triplet of base vectors and dual vectors in current state Triplet of base vectors and dual vectors in reference state Total energy Total energy on microscopic level Internal energy density per unit volume Continued on next page

Coarse Graining in Elasto-viscoplasticity Symbol

Meaning

eˆ F Fˆ

Internal energy density per unit mass Total deformation gradient Deformation gradient density Elastic (recoverable) deformation gradient Volume-constrained elastic deformation gradient, det F˜ e = 1 Constant of motion Heat flux Fluctuating part of the heat flux Poisson operator Poisson operator on microscopic level Different levels of description Friction matrix Particle mass Surface normal to sliding plane in current state Anisotropy tensor along 3-axis Orthonormal triad of anisotropy vectors in reference state Projection in the space of deformation gradients Pressure (scalar) Momentum Momentum of particle i Cartesian coordinate in reference state Cartesian coordinate in current state Cartesian coordinate of particle i in current and reference state, respectively Difference vector between particles i and j in current and reference state, respectively Dual vector to difference vector rij0 (see Section 5.2.1) Entropy Entropy density per unit volume Entropy density per unit mass Sliding direction in current state Absolute temperature Matrix transpose when used, e.g., as LT Time Momentum density Velocity field

Fe F˜ e I jq jq,f L L0 L0 , L1 , L2 M m mc Nr = n3r n3r nir P p p pi R r, r ri , ri0 rij , rij0 rˆ ij0 S s sˆ sc T T t u v

Continued on next page

255

256


Symbol WF wij x Z z

Meaning

e

λ λ λq μ x (z) ρ ρx (z)

Fluctuation in the deformation gradient Fluctuations, see Eq. (5.25) List of dynamic variables Partition function List of microscopic degrees of freedom; short-hand notation for (r1 , . . . , rN , p1 , . . . , pN ) Dirac delta function, e.g., δ(r − r ) functional derivative when used, e.g., as δE/δx Kronecker delta Friction coefficient Viscosity, viscosity tensor Bulk viscosity Transposed velocity gradient Plastic velocity gradient tensor in current state Plastic velocity gradient tensor in reference state Tensor describing the relaxation of Fe Correlation of fluctuations on deformation gradient, see Eq. (5.20) Factor of spatial dilation (see Table 5.1) List of Lagrange multipliers Thermal conductivity tensor Chemical potential Instantaneous value of x as expressed in terms of z Mass density Distribution function of microstates z

dev σ σ σ dev σf σt σv τ, τc1 , τc2 D ∂ Dt = ∂t + v ·

Driving force for plastic deformation (stress tensor) Rate of local entropy production per unit mass Elastic contribution to the Cauchy stress tensor Deviatoric part of σ, σ dev = σ − 13 (trσ)1 Fluctuating part of the stress tensor Total stress tensor Viscous contribution to the stress tensor Time scales separating different levels of description Potential energy Substantial derivative, material derivative

δ δ δij ζ η, η κ κ = ∂v/∂r κp,c , κ˘ p,c κp,r , κ˘ p,r ¯

∂ ∂t ∂ ∂ ∂r , ∂r

∂ ∂r

Partial derivative with respect to time t, at constant current position r Partial derivative with respect to r and r , respectively

Coarse Graining in Elasto-viscoplasticity

257

1. Introduction The dynamics of matter can be described on different levels of detail. Since each specific level of description has its benefits and drawbacks, one aims for a strategy that combines the benefits only, leaving out the drawbacks. For example, one would hesitate to describe the flow of water in a (macroscopic) channel by Newton’s equations of motion for the atoms because the amount of detailed information would be overwhelming, which in turn would disguise the phenomena relevant on the macroscopic scale. Coarse-grained descriptions such as the Navier–Stokes equations are, therefore, used. A most important link between the macroscopic and microscopic descriptions is established through the so-called fluctuation–dissipation theorem (de Groot and Mazur, 1962; Kubo et al., 1991; Evans and Morriss, 1990; Öttinger, 2005), which explains how dissipative effects emerge as a result of coarse graining. In particular, the Green–Kubo formula relates the shear viscosity to the correlations between fluctuations of the microscopic shear stress. Relations of this type are frequently used in molecular dynamics simulations to determine macroscopic transport properties (Evans and Morriss, 1990), expressed in terms of two-time correlations of current densities. Therefore, through fluctuation–dissipation theorems, one can combine the benefits of the macroscopic and the microscopic descriptions. While macroscopic descriptions provide a general framework suitable for studying large-scale complex processes in general terms, for example, macroscopic evolution equations and conservation laws, the microscopic description can be used to incorporate material-specific ingredients into that macroscopic theory, for example, the viscosity and the thermal conductivity. In a more general context, it has been recognized that the technical aspects of coarse graining are closely tied with projection operator techniques (Grabert, 1982), with the aid of which the hydrodynamic equations can actually be derived (e.g., see Section 5.1). It is discussed in this contribution whether, and to what extent, the same strategies for coarse graining can be applied in relation to elasto-viscoplastic deformation of solid materials. Current elasto-viscoplastic models of solid materials are often formulated on the macroscopic scale in terms of one or several tensorial variables that describe the recoverable (i.e., elastic) state of deformation of the material. The viscoplastic effects are captured by so-called plastic velocity gradient tensors, which enter into the evolution equations of the elastic deformation tensors, and for which constitutive equations are needed (Besseling and Van der Giessen, 1994, page 13). The question arises of how to obtain an expression for the plastic velocity gradient tensor suitable for a particular system. For example, appropriate expressions for the plastic velocity gradient tensor have been developed and applied successfully for the case of viscoplastic deformation of isotropic materials, for example, amorphous

258


polymers (Boyce et al., 1988; Steenbrink et al., 1997; Tervoort et al., 1998), and crystalline solids with a finite number of slip systems (Hutchinson, 1976; Asaro, 1983; Peirce et al., 1983; Pan and Rice, 1983). Such relations have two ingredients. First, the tensorial form of the plastic velocity gradient tensor must be determined, which for anisotropic materials depends on the anisotropy axes of the material. This can be achieved by identifying specific plastic deformation processes at a molecular level, for example, crystalline slip (Hutchinson, 1976; Asaro, 1983; Peirce et al., 1983; Pan and Rice, 1983), or by applying the representation theorem of tensor functions (Wang, 1970, 1971; Spencer, 1971; Loret, 1983; Dafalias, 1983, 1985a). The second ingredient consists of specifying kinetic coefficients, that is, viscosity functions, which describe the rate of viscoplastic deformation. Typically, the value of these coefficients is obtained from experiments. This can be a tedious, and often non-unique, process when the phenomenological model involves a large number of material parameters. By contrast, we pose the following question: What can one learn about the constitutive equation for the plastic velocity gradient tensor by using the coarse graining techniques mentioned in the previous paragraph? In this manuscript, our objective is to link the macroscopic field theory of elasto-viscoplasticity with the microscopic dynamics of the constituent particles. Specifically, we aim at obtaining expressions for the plastic velocity gradient tensor from microscopic fluctuations and correlations between them. As the guideline to perform this task, the general equation for the nonequilibrium reversible– irreversible coupling (GENERIC) formalism of nonequilibrium thermodynamics (Öttinger, 2005; Grmela and Öttinger, 1997; Öttinger and Grmela, 1997) is used as explained below. The chapter is organized as follows. The GENERIC framework of nonequilibrium thermodynamics is presented in Section 2, and illustrated with examples in Section 3, including microscopic Hamiltonian point mechanics, and the macroscopic field theories of nonisothermal hydrodynamics and elasto-viscoplasticity. Particularly, Section 3.4 gives a brief overview of our earlier efforts to model nonisothermal anisotropic elasto-viscoplasticity in macroscopic terms (Hütter and Tervoort, 2008a,b). In Section 4, the specific aspects of the thermodynamics framework as related to coarse graining are introduced. The corresponding scheme is then applied in Section 5. As an illustrative example, the hydrodynamic equations are derived from the microscopic Hamiltonian point mechanics in Section 5.1. Section 5.2 is concerned with the link between macroscopic elasto-viscoplasticity and the microscopic dynamics of the constituent atoms or molecules. In Section 5.2.4, we discuss in detail the influence of material symmetry on the tensorial structure of the plastic velocity gradient tensor, with illustrative examples in Sections 5.2.5–5.2.7. The results are discussed in Section 6.


259

2. GENERIC Framework of Nonequilibrium Thermodynamics. I. Fundamentals

2.1. Introduction Techniques of nonequilibrium thermodynamics act as a guard-rail, helping the modeler to cast the understanding of a complex system, often with internal variables, in a form that complies with certain principles of thermodynamics. There is a wide variety of approaches to nonequilibrium thermodynamics modeling, and the relations between many of them have been established (see Grmela, 1997; Jongschaap and Öttinger, 2001 and references cited therein). Here, we choose the general equation for the nonequilibrium reversible–irreversible coupling (GENERIC) framework developed by Grmela and Öttinger (Grmela and Öttinger, 1997; Öttinger and Grmela, 1997; Öttinger, 2005), which is used to describe mechanically and thermally isolated systems. In regard to the topic of this contribution, this method has two important advantages over other methods. First, the GENERIC structure is postulated to hold on different levels of description, for example, on the microscopic level of Hamiltonian point mechanics and for the macroscopic continuum field theories including hydrodynamics and elastoviscoplasticity. Second, the framework provides procedures for how to relate its fundamental building blocks at the different levels. In the following, we give an introduction to the formalism; for more details, the reader is referred to the book of Öttinger (2005). The aspects related to coarse graining are discussed separately in Section 4.

2.2. Choice of Variables The first step in modeling the dynamics of a complex system consists in choosing a set of variables, x, that describes the system of interest to the desired detail. This step must be taken with care and requires some understanding of the physics that one aims to capture. Choosing too small a set is equivalent to neglecting certain aspects of the system, a defect that cannot be repaired by the subsequent steps of the approach. The right choice of variables is, therefore, as important as it is in equilibrium thermodynamics.

2.3. Two-generator Idea, Separation of Reversible and Irreversible Terms Except for the most microscopic level of description, the evolution equation of the variables x contains two fundamentally different contributions. There are

260


reversible contributions, which are under “mechanistic control,” and irreversible contributions, which account for the remaining part of the evolution equations of x. In the GENERIC framework, the form of the reversible contribution is inspired by Hamiltonian dynamics in the sense that the partial time derivative of the variables x equals δE ∂x , (2.1a) =L· ∂t rev δx that is, it is driven by the derivative of the total energy E and involves a Poisson operator L. The total energy E typically consists of the kinetic energy on the one hand and of an interaction energy or internal energy on the other hand. In the presence of field variables, δE/δx is a functional derivative (e.g., see Morrison, 1998; Parr and Yang, 1989) and the symbol “·” implies not only a discrete summation but also integrations over spatial degrees of freedom (see examples below). The irreversible contribution to the evolution equation of x is given by a generalized friction matrix M acting on the functional derivative of the entropy S, ∂x δS (2.1b) =M· . ∂t irr δx With the definition of a scalar product, the Poisson operator is equivalent to a Poisson bracket { , } (Marsden and Ratiu, 1999), and the friction matrix can be associated with a so-called dissipative bracket [ , ] (Grmela, 1984; Beris and Edwards, 1994), δA δB ·L· , δx δx δA δB [A, B] = ·M· , δx δx

{A, B} =

(2.2a) (2.2b)

for two arbitrary functionals A and B. Therefore, Poisson brackets not only play a most prominent role in the Hamiltonian dynamics but have been introduced also into the field of nonequilibrium thermodynamics, and are now being exploited in the GENERIC framework as well.

2.4. Full Structure In summary, the full dynamics for the variables x is given by ∂x ∂x δS ∂x δE = +M· , + =L· ∂t ∂t rev ∂t irr δx δx

(2.3a)


261

which is supplemented by certain conditions on the operators L and M, namely 1. L must be antisymmetric, that is, LT = −L ,

resp.

{A, B} = − {B, A} ;

(2.3b)

2. L must satisfy the Jacobi identity, that is, respect the time–structure invariance (e.g., see pp. 14–16 in Öttinger (2005) for details), {A, {B, C}} + {B, {C, A}} + {C, {A, B}} = 0 ;

(2.3c)

3. L must satisfy the degeneracy condition for the entropy S, L · (δS/δx) = 0 ,

resp.

{A, S} = 0 ;

(2.3d)

4. M is usually symmetric, MT = M,

resp.

[A, B] = [B, A] ;

(2.3e)

more precisely, the friction matrix M must be Onsager–Casimir symmetric (de Groot and Mazur, 1962; Kreuzer, 1981), which is discussed in due detail in Section 3.2.1 of Öttinger (2005); 5. M must be positive semidefinite, [A, A] ≥ 0;

(2.3f )

6. M must satisfy the degeneracy condition for the energy E, M · (δE/δx) = 0,

resp.

[A, E] = 0,

(2.3g)

where A, B, and C are arbitrary functionals of the variables x. The first two conditions on L are well known for Poisson brackets in classical mechanics, and hence they ensure that the reversible dynamics in the GENERIC framework possesses the full structure known for Hamiltonian mechanics. The third condition states that the entropy is not changed as a result of the reversible dynamics. The first condition on M implies the symmetry of the matrix of phenomenological transport and relaxation coefficients, for example, the symmetry of the viscosity tensor and of the thermal conductivity tensor, but also addresses the form of possible cross-couplings, for example, the thermoelectric effects (de Groot and Mazur, 1962; Kreuzer, 1981). The second and the third conditions on M guarantee that the

262


entropy is a nondecreasing function of time and that the total energy is conserved: δE ∂x δE δE δS dE = · = · L· +M· = 0, dt δx ∂t δx δx δx dS δS ∂x δS δE δS δS δS = · = · L· +M· = ·M· ≥ 0, dt δx ∂t δx δx δx δx δx

(2.4) (2.5)

where, again, the symbol “·” implies not only a discrete summation but also integrations over continuous indices. The conservation of certain quantities I(x) by the evolution equations can be incorporated in two distinct ways. On the one hand, the sufficient conditions, L · (δI/δx) = 0,

(2.6a)

M · (δI/δx) = 0,

(2.6b)

can be used as constraints when constructing the building blocks for the evolution equation (2.3). On the other hand, one can also check the condition dI/dt = (δI/δx) · (∂x/∂t) = 0 once the evolution equations have already been formulated. As examples for conserved quantities I in closed systems, in addition to the total energy E, we mention the total mass, the linear momentum, and the angular momentum. In practical applications, the determination of the Poisson operator L can follow three rather different routes. First, if one knows specifics about the evolution equa∂ tion of x, for example, the change of the mass density in flow, ∂ρ/∂t = − ∂r · (ρv), one can deduce some elements of L (see Section 3.3). Subsequently, other (ideally all) elements are determined by way of the conditions (Eqs. (2.3b–2.3d)). If this procedure does not specify all elements of the Poisson operator, the other two routes described in the following can be employed. In the second strategy for the determination of the Poisson operator, particularly for systems with spatial motion, the transformation behavior of the variables x under inhomogeneous space transformations can be exploited to deduce the Poisson operator (see Appendix B in Öttinger (2005) and references cited therein). The third procedure, suitable when x are coarse (large scale) variables, consists in deriving the Poisson operator L by coarse graining from the dynamics on a more fine-grained level of description. The first and the third approaches will be illustrated in detail below. As a side note, it is mentioned that the verification of the Jacobi identity is often tedious, in which case the use of a computer program for symbolic calculations is recommended (Kröger et al., 2001). The friction matrix M can be specified in different ways. On the one hand, one commonly departs from some known irreversible contributions in the evolution


263

equations and reformulates them in terms of Eq. (2.1b). With the aid of the conditions (2.3e–2.3g), the thermodynamically required ramifications of the known effects in all equations can be examined. Furthermore, following that route, one can also introduce generalizations in a thermodynamically consistent fashion. On the other hand, a distinct procedure invokes the so-called fluctuation–dissipation relations, that is, the fact that irreversible effects on a certain coarse level of description are due to rapid, uncontrollable motions, that is, fluctuations, the dynamics of which can only be resolved on a finer level. This approach is the main topic of this chapter, particularly how it can be applied in the field of rate-dependent plasticity. Before proceeding with some illustrative examples, we take the opportunity to clarify the notation used in the GENERIC evolution equation (2.3a) when applied to field theories. For variables x that depend on the spatial position r, the evolution equations in (2.3a) read in explicit component notation1 ∂xi (r) = ∂t

k

Lik (r, r )

δE 3 d r + δxk (r )

Mik (r, r )

k

δS d 3 r . (2.7) δxk (r )

In other words, in general, the change of the variables x at position r is affected by the driving forces not only at the same position but also at all other positions in space. It is reasonable to assume though that Lik (r, r ) and Mik (r, r ) vanish for sufficiently large distances |r − r |. Particularly, in many common field theories, both operators vanish for all |r − r | = 0, leading to what is commonly called local field theories.

3. Applications of the GENERIC Formalism

3.1. Hamiltonian Point Mechanics The state of a system of N point particles of masses mi can be described by the positions ri and the momenta pi of the particles, and thus the full set of variables is given by x = ({ri }i=1,...,N , {pi }i=1,...,N ).

(3.1)

1 Throughout the entire chapter, Latin indices are used in general, except for Cartesian components of vectors and tensors, where Greek indices are employed. Furthermore, the summation over Latin indices is spelled out, while Einstein’s summation convention is used for Greek indices that occur twice, that is, for the summation over Cartesian components.

264


The total energy of that system consists of the kinetic and potential energies, while the entropy at this level of description is zero, since there is only one microstate for each given x. In other words, E=

N p2i + , 2mi

(3.2a)

i=1

S = 0,

(3.2b)

where denotes the sum of all interaction energies. With the Poisson operator given by (Marsden and Ratiu, 1999) 0N 1N L= , (3.3) −1N 0N with 0N and 1N the 3N-dimensional zero matrix and identity matrix, respectively, one recovers immediately from (2.3a) the well-known evolution equations pi , mi ∂ p˙ i = − . ∂ri r˙ i =

(3.4a) (3.4b)

Since the Poisson bracket associated with (3.3), {A, B} =

N ∂A n=1

∂B ∂A ∂B , · − · ∂rn ∂pn ∂pn ∂rn

(3.5)

satisfies the conditions (2.3b–2.3d), one concludes that Hamilton’s equations of motion are included in the GENERIC framework.

3.2. Single Particle in Spring Potential with Linear Drag Force As a next example, we consider a single particle of mass m in a potential and immersed in a viscous liquid that exerts a friction force on the particle. Since the friction slows down the motion of the particle, mechanical energy is dissipated. To simplify the discussion, it is assumed that the dissipated energy is taken up entirely by the immersing liquid, while the particle itself is completely athermal. Fluid flow in the viscous liquid is neglected. As the set of variables to describe the closed system of particle plus liquid, we choose x = (r, p, S ),

(3.6)


265

with r being the particle position, p the momentum, and S the entropy of the liquid. The energy is of the same form as (3.2a) with potential energy plus a contribution Eliq representative of the internal energy of the liquid. As the particle is assumed to be athermal, the total entropy is identical to the variable S. If the mass and the volume of the liquid are considered constant, the internal energy of the liquid is a function of the entropy S only and therefore E=

p2 + (r) + Eliq (S). 2m

(3.7)

The derivatives of total energy E and entropy S are then given by ⎛ ⎞ ∂/∂r δE ⎝ = p/m ⎠, δx T

⎛ ⎞ 0 δS = ⎝ 0 ⎠, δx 1

(3.8)

with the temperature of the liquid defined as T = dEliq /dS. The reversible evolution of x is not influenced by friction. In other words, the reversible dynamics of the particle is given by the usual Hamilton’s equations of motion, while the total entropy equals the entropy of the liquid S and remains constant. In regard to the Poisson operator (3.3) and the functional derivatives (3.8), we set ⎛

0 L = ⎝ −1 0

1 0 0

⎞ 0 0 ⎠, 0

(3.9)

which satisfies the GENERIC conditions (2.3b–2.3d). The upper-left block is of the common symplectic form, while the vanishing last row and column are introduced to accommodate the degeneracy with respect to the entropy. The only effect leading to irreversible dynamics in this example is the friction of the particle, which is assumed to be represented by a linear drag force. The construction of the corresponding friction matrix M begins with the observation that the friction affects the particle momentum and the thermal variable of the liquid, but it does not lead to an irreversible term in the evolution of the particle position. Therefore, the first row and, due to the symmetry, the first column of M are set equal to zero. In the next step, one focuses on the element M(p,S ) since by virtue of the entropy gradient in (3.8) only that element can contribute to the usual form of the linear drag force, −ζp/m, in the momentum equation, with friction coefficient ζ ≥ 0. We, thus, conclude M(p,S ) = −ζp/m. The degeneracy condition (2.3g) leads to M(p,p) = ζT 1. Due to the symmetry of M, one has

266


M(S,p) = −ζp/m, and the degeneracy requires M(S,S) = (ζ/T )(p/m)2 , that is, ⎛

0

0

⎜ 0 M = ζ⎜ ⎝

T1

0

p −m

0

⎞

p ⎟ −m ⎟. ⎠

(3.10)

p2

1 T m2

While this friction matrix is symmetric and satisfies the degeneracy condition (2.3g) by construction, one can also show that it is positive semidefinite, that is, it complies with all conditions (2.3e–2.3g). Collecting all contributions to the evolution equations (2.3a), one obtains p , m p ∂ −ζ , p˙ = − ∂r m ζ p2 S˙ = . T m2 r˙ =

(3.11a) (3.11b) (3.11c)

The entropy is a nondecreasing function of time since the friction coefficient is ˙ assumes the ˙ liq = T S, positive semidefinite. The energy gain in the liquid, E expected form.

3.3. Nonisothermal Hydrodynamics In this third example, we are concerned with formulating nonisothermal hydrodynamics of a compressible liquid. There are extensive discussions about the corresponding dynamics, and we shall concentrate here only on its formulation in the context of the GENERIC framework for illustrative purposes. For further details on the following treatment, the reader is referred to Öttinger (2005). Due to compressibility of the liquid, the mass density ρ(r) becomes a dynamic variable, in addition to the momentum density u(r).2 Nonisothermal conditions can be accounted for by including a “thermal” variable. Instead of the temperature itself, it will prove to be more convenient to choose the internal energy density e(r) per unit volume so that the full set of variables is given by x = (ρ(r), u(r), e(r)).

(3.12)

2 It is not recommended to use the velocity field v(r) as a dynamic variable since, first, it is not the density of a conserved quantity and, second, it would lead to a significantly more complicated expression for the Poisson operator.


267

In terms of these variables, the total energy and entropy can be written in the form 1 u(r)2 E= (3.13a) + e(r) d 3 r, 2 ρ(r) (3.13b) S = s (ρ(r), e(r)) d 3 r, where the entropy density s(ρ, e) per unit volume contains the full thermodynamic characteristic of the liquid. Assuming local equilibrium, that is, equilibrium within each volume element d 3 r, the function s(ρ, e) can be deduced from its equilibrium counterpart. If for a homogeneous many-particle system with total mass M and total energy E in volume V the entropy function is given by S(M, E, V), then one obtains 1 (3.14) s(ρ, e) = S(M, E, V) = S(M/V, E/V, 1), V where we have made use of the fact that S is a homogeneous function of degree one in all of its extensive arguments. From (3.14), it is not only obvious that the local entropy density is indeed a function of ρ = M/V and e = E/V but also the partial derivatives ∂s(ρ, e)/∂ρ and ∂s(ρ, e)/∂e can be interpreted. In particular, multiplying the first equation in (3.14) with V, one finds for the derivative with respect to M, E, and V, ∂s(ρ, e) ∂S(M, E, V) μ = =− , ∂ρ ∂M T ∂s(ρ, e) ∂S(M, E, V) 1 = = , ∂e ∂E T ∂s(ρ, e) ∂s(ρ, e) ∂S(M, E, V) p s(ρ, e) − ρ −e = = , ∂ρ ∂e ∂V T

(3.15a) (3.15b) (3.15c)

where in all these equations, the second equality makes use of the standard definitions of temperature T , chemical potential μ, and pressure p. With these identifications, the functional derivatives of E and S become ⎞ ⎛ 1 − 2 v(r)2 δE = ⎝ v(r) ⎠, δx(r) 1 ⎛ μ(r) ⎞ − δS ⎜ T(r) ⎟ = ⎝ 0 ⎠, δx(r) 1 T(r)

with velocity field v = u/ρ.

(3.16a)

(3.16b)

268


For the specification of the Poisson operator L, we start with noting that it depends on both r and r , according to (2.7), and the action of the Poisson operator on the energy gradient involves an integration over r . If the only reversible effects are due to the flow field v, then only the momentum column and row are nonzero, in view of the u-component of the functional derivative (3.16a). As explained in the following, the Poisson operator is given by ⎛ ⎞ 0 ρ(r ) ∂r∂δ 0 γ ⎜ ⎟ ⎜ ∂δ ⎟ ∂δ ∂δ ∂δ ∂δ L(r, r ) = ⎜− ∂rα ρ(r) uα (r ) ∂rγ − ∂rα uγ (r) − ∂rα e(r) − ∂rμ p(r )δαμ⎟, ⎝ ⎠ 0 e(r ) ∂r∂δ + p(r)δγμ ∂r∂δ 0 γ

μ

(3.17) where δ = δ(r − r ) is the Dirac delta function. In the elements L(u,e) and L(e,u) , p is an unspecified function at this point, and the Kronecker delta has been introduced for later convenience. Subscript α implies contraction with a vector Aα multiplied from the left, while subscript γ implies contraction with a vector Aγ multiplied from the right. Einstein’s summation convention is used for Greek indices that occur twice. It is essential to note that all positional derivatives act only on the delta functions. The entries in the above Poisson operator can be motivated as follows. We assume that the convective parts to the evolution equation of x are known. For example, the mass balance can be written in the form ∂ ∂δ(r − r ) ∂ρ(r) = − · δ(r − r )ρ(r )v(r )d 3 r = ρ(r ) · v(r )d 3 r , ∂t ∂r ∂r (3.18) where we have used ∂δ/δr = −∂δ/δr . By virtue of δE/δu(r ) = v(r ), one obtains the element L(ρ,u) = ρ(r )∂δ/∂r . Since, generally, the transpose element is obtained by transposing both discrete and continuous indices, one obtains L(u,ρ) = −ρ(r)∂δ/∂r. Along similar lines, the transport terms of the momentum density can be written in the form ∂δ ∂ (3.19) − · (v(r)u(r)) = u(r ) · v(r )d 3 r . ∂r ∂r As this term is to be generated by L(u,u) and since the latter must be antisymmetric, one obtains the entry specified in (3.17). The entries L(u,e) and L(e,u) can be motivated in a similar way. After multiplication of L(r, r ) with δS/δx(r ) and integration over r , one concludes that the Poisson operator (3.17) satisfies the degeneracy condition (2.3d) if the function p in (3.17) is equal to the pressure


269

defined in (3.15c) (see Appendix A). Finally, Eq. (3.17) is antisymmetric with respect to transposing both discrete and continuous indices and satisfies the Jacobi identity (2.3c). The irreversible effects we aim at describing by the friction matrix M include viscous effects and heat conduction. Since there are no irreversible effects in the evolution equation for the mass density, the first row and, due to the symmetry, the first column of M are equal to zero, ⎞ ⎛ 0 0 0 (3.20a) M(r, r ) = ⎝ 0 M (uα ,uγ ) (r, r ) M (uα ,e) (r, r ) ⎠, 0 M (e,uγ ) (r, r ) M (e,e) (r, r ) with the index convention defined after (3.17). As can be justified by their action discussed further below, the nonvanishing elements are given by M (uα ,uγ ) (r, r ) =

∂ ∂ ηαβγ Tδ , ∂rβ ∂r ∂vγ

∂ ηαβγ δ , ∂rβ ∂v ∂ α M (e,uγ ) (r, r ) = T ηαβγ δ , ∂rβ ∂r M (uα ,e) (r, r ) =

∂r

T

M (e,e) (r, r ) = ηαβγ T

∂vα ∂vγ ∂ ∂ q 2 λμν T δ , δ + ∂rβ ∂r ∂rμ ∂rν

(3.20b) (3.20c) (3.20d) (3.20e)

where, again, δ = δ(r − r ). All other functions are evaluated at r, except when using a prime in the superscript to denote evaluation at r . The symbols ηαβγ and q λμν stand for the tensors of viscosity and thermal conductivity, respectively. With the above specifications, it can be shown that the degeneracy condition (2.3g) is satisfied (see Appendix A). In this respect, we note that, due to our interest in local field equations of isolated systems, one can neglect the boundary terms that appear as a result of integrations by parts with respect to r .3 With the properties ηαβγ = ηγαβ ,

(3.21a)

λqμν = λqνμ ,

(3.21b)

Aαβ ηαβγ Aγ ≥ 0, Bμ λqμν Bν ≥ 0,

for all Aαβ ,

(3.21c)

for all Bμ ,

(3.21d)

the symmetry and positivity conditions (2.3e–2.3f) are fulfilled. Note that the framework imposes no conditions other than (3.21) on the tensors of viscosity 3 For an analysis of the boundary terms, it is recommended to use the Poisson and dissipative brackets, instead of the corresponding operators, for formulating the dynamics.

270


and thermal conductivity. Particularly, both these quantities can be complicated functions of the field variables x. The full set of evolution equations (2.7) for nonisothermal compressible hydrodynamics is given by the Poisson operator (3.17) and the friction matrix (3.20) acting on the functional derivatives (3.16). After careful book-keeping of indices and integration variables, using partial integrations with respect to r , and neglecting boundary terms once more, one arrives at (see Appendix A) ∂ ∂ρ = − · (vρ), ∂t ∂r ∂ ∂ ∂u = − · (vu) + · σt, ∂t ∂r ∂r ∂ ∂ q ∂e = − · (ve) + σ t : κ − ·j , ∂t ∂r ∂r

(3.22a) (3.22b) (3.22c)

with transposed velocity gradient κ = ∂v/∂r and heat flux jq . The total stress tensor σ t consists of a scalar pressure term and a contribution due to viscous stresses, σ t = −p1 + σ v . Since the GENERIC procedure leads to a closed set of evolution equations (2.3a), one also obtains constitutive relations for the viscous stress tensor and for the heat flux, namely v σαβ = ηαβγ κγ , ∂T q q . jμ = −λμν ∂rν

(3.23a) (3.23b)

These two relations represent the well-known laws of Newton and Fourier for viscous flow and the transport of heat, respectively. Note that the symmetry of the viscous stress tensor is guaranteed by requiring symmetry of ηαβγ with respect to the interchange of the first two or the last two indices. In retrospect, the result (3.22, 3.23) plus the GENERIC criteria serve as a justification for the specific choice (3.20) for the friction matrix. For the special case of an isotropic liquid, the common ansatz for the viscosity tensor that respects the conditions (3.21) is (Beris and Edwards, 1994) 2 ηαβγ = η(δαγ δβ + δα δβγ ) + κ − η δαβ δγ , (3.24a) 3 with shear viscosity η ≥ 0 and bulk viscosity κ ≥ 0, that both can depend on temperature and pressure. In turn, the viscous stress tensor assumes the form 2 σ v = η κ + κT + κ − η (trκ)1, (3.24b) 3 in agreement with literature.


271

It can be shown by direct calculation that the total mass, the total momentum, and the total angular momentum, (3.25a) I1 (x) = ρ(r) d 3 r, (3.25b) I2 (x) = u(r) d 3 r, I3 (x) = r × u(r) d 3 r, (3.25c) are conserved under the evolution equations (3.22). In the above formulation of the nonisothermal compressible hydrodynamics in the GENERIC framework, we have profited several times from knowing the form of the final equations while constructing the building blocks. In the procedure presented in Section 5.1, which is based on coarse graining, such anticipation is absent, and rather the microscopic dynamics of the constituent particles is understood and exploited as the reason for the macroscopically observed behavior.

3.4. Macroscopic Elasticity and Elasto-viscoplasticity This example intends to demonstrate that GENERIC is not limited to (complex) liquids but can also be applied to describe elastic and inelastic deformations in solid mechanics. The traditional continuum mechanical description of elastic and inelastic deformations typically starts with a mathematical formulation of strains and strain rates (kinematics and kinetics). This is followed by the specification of the balance laws of mass, energy, momentum, and angular momentum, supplemented with the second law of thermodynamics, detailing the evolution of entropy. This latter set of balance laws and the entropy evolution, which are all applicable to any deforming body, is then closed with constitutive equations that address material-specific behavior. For reasons of internal consistency and comparison with GENERIC, it is reasonable to recapitulate these equations briefly. A more detailed overview can be found in several texts, for example, Truesdell and Noll (1992); Besseling and Van der Giessen (1994). 3.4.1. Kinematics and Kinetics The deformation of a body is conveniently described from a Lagrangian or material point of view, by specifying the position vector r(R, t) of a material point in the current state, which has coordinates R in an arbitrary reference state. The deformation gradient, defined as the bivector F = ∂r(R, t)/∂R, then maps infinitesimal line elements in the reference state to corresponding line elements in

272


the current state. Infinitesimal volume elements in the current state and reference state, dV and dV0 , respectively, are related by dV = JdV0 , with the so-called relative volume change J = det F. Typically, the deformation gradient is used to construct deformation measures that omit rigid rotations of line elements, and that are specified either with respect to the current state, such as the left Cauchy–Green strain tensor B = F · FT , or with respect to the reference state, such as the right Cauchy–Green strain tensor C = FT · F. The velocity field v is defined as v = ∂r(R, t)/∂t, from which it follows that the evolution of the deformation gradient F and the relative volume change J are given by ∂F ∂ = −v · F + κ · F, ∂t ∂r ∂ ∂J = −v · J + Jtrκ, ∂t ∂r

(3.26a) (3.26b)

with the transposed velocity gradient κ = ∂v/∂r. 3.4.2. Balance Equations Assuming local equilibrium (see Section 3.3), the balance laws of continuum mechanics, which apply to any deforming body, lead to the evolution equations for mass density ρ, momentum density u = ρv, and internal energy density e specified in (3.22), where body forces have been neglected. The total Cauchy stress tensor σ t specifies the surface traction t on the boundary of a volume element with outward unit normal vector n as t = σ t · n in the current configuration. Conservation of the angular momentum states that the Cauchy stress tensor is symmetric, σ t = σ t,T. Finally, given the local entropy and internal energy densities per unit mass, sˆ = s/ρ and eˆ = e/ρ, respectively, the generalized second law of thermodynamics states that the local entropy production rate per unit mass σ must be nonnegative. With the definition of the material derivative D/Dt = ∂/∂t + v · ∂/∂r, one can define σ as the change in the entropy density per unit mass corrected by the entropy ∂ · (jq /T ), leading to the Clausius–Duhem flux term, that is, σ = Dˆs/Dt + (1/ρ) ∂r inequality (Truesdell and Noll, 1992), ρσ = jq ·

1 Dê ∂ 1 1 Dˆs − ≥ 0, + σt : κ + ρ ∂r T T Dt T Dt

(3.27)

where the underlined term is often absorbed in a modified definition of σ. This inequality is being used as a restriction on constitutive choices for jq and σ t . Additional restrictions are obtained by demanding that constitutive relations should be invariant under changes of frame of reference, which is referred to as the principle of material frame indifference or objectivity (Truesdell and Noll, 1992, p. 44).


273

3.4.3. Finite Anisotropic Thermoelasticity: GENERIC Formulation To obtain a closed set of evolution equations, the general balance laws (3.22) must be supplemented with material-specific constitutive equations for the stress tensor and the heat flux. One possible strategy is to express the stress tensor and heat flux as functionals of the history of the independent variables ρ, u, and e, related to the principle of fading memory developed by Coleman and Noll (see Coleman and Noll , 1960; Truesdell and Noll, 1992, p. 101, and references cited therein). Another possibility is to identify structural variables, sometimes called “internal” or “hidden” variables, that, together with the independent hydrodynamic variables, fully determine the state of the material. The constitutive behavior then follows from the evolution equations of these structural variables combined with the evolution of the hydrodynamic variables as described by the general balance laws. The latter scheme is the one contained in GENERIC and will be demonstrated in this example for deriving the Eulerian description of finite anisotropic thermoelastic behavior, with an extension to account for the viscoplastic effects in the next section. As stated above, the first step to describe thermoelasticity in GENERIC is to identify the structural and hydrodynamic variables. At first sight, an obvious choice to describe the state of deformation would be either the left or right Cauchy–Green strain tensor or strain tensors derived therefrom. The evolution equations for B and C follow from the evolution equation for F (3.26a), ∂C ∂ = −v · C + FT · (κ + κT ) · F, ∂t ∂r ∂B ∂ = −v · B + κ · B + B · κT . ∂t ∂r

(3.28a) (3.28b)

While the evolution of C requires knowledge of F, the evolution of B does not, which is suggestive of using B as a structural variable for a theory with a closed set of evolution equations. However, anisotropy of the material is most naturally specified with respect to the reference configuration, which would suggest the use of C rather than B, the latter being invariant with respect to rotation (i.e., anisotropy) in the reference state. This conflict led Hütter and Tervoort (2008a) to use the deformation gradient F itself as structural variable, as it has a self-contained evolution equation, (3.26a), and can be used in an Eulerian formulation to construct invariant strain-measures, such as C. In addition to F, the momentum density u and temperature T were selected to describe finite anisotropic thermoelastic deformation. However, to relate to the Poisson operator L derived in the Section 3.3, we will use here the internal energy e instead of T , that is, we select as set of variables x = (u, e, F).

(3.29)

274


As in the previous section, the total energy and the entropy can be described in the general form E=

u2 /(2ρ) + e d 3 r,

(3.30a)

S=

s (e, F) d 3 r.

(3.30b)

The function s(e, F) contains the full information about the thermodynamic properties of the material. Note that the mass density ρ does not feature in the list of independent variables, as it is now related to the volumetric part of the deformation gradient by way of the relation ρ = ρ0 / det F, with ρ0 being the mass density in the reference state. The functional derivatives of the total energy and entropy then read ⎛

vα

⎞

⎟ δE ⎜ 1 ⎟, =⎜ ⎝ ⎠ δx 2 − v2 ∂F∂ραβ

⎛

0

⎞

⎜ 1 ⎟ δS ⎟ =⎜ ⎝ T ⎠, δx ∂s(e,F)

(3.31)

∂Fαβ

where we have used the definition v = u/ρ for the velocity field, and the temperature T is defined by T −1 = (∂s/∂e)|F . Note that with eˆ = e/ρ and sˆ = s/ρ, the energy density and entropy density per unit mass, respectively, the temperature can be expressed also in the form T −1 = (∂ˆs/∂ê)F . The Poisson operator L can be constructed in a manner similar to the case of nonisothermal hydrodynamics as shown in the previous section. The component L(u,u) follows again from the advection of the momentum density. The elements L(F,u) and L(u,F) are derived from the evolution equation for F (3.26a) and the antisymmetry condition (2.3b), respectively. We, thus, write ⎛ ⎞ uα (r ) ∂r∂δ − ∂r∂δα uγ (r) − ∂r∂δα e(r) + ∂r∂δμ σαμ (r ) L(uα ,Fγ ) (r, r ) ⎜ ∂δ γ ⎟ ∂δ ⎟, L(r, r ) = ⎜ 0 0 ⎝e(r ) ∂rγ − σγμ (r) ∂rμ ⎠ L(Fαβ ,uγ ) (r, r ) 0 0 (3.32a) with L(Fαβ ,uγ ) (r, r ) = − L(uα ,Fγ ) (r, r ) =

∂Fαβ (r ) ∂δ(r − r ) δ(r − r ) + Fμβ (r)δαγ , (3.32b) ∂rγ ∂rμ

∂Fγ (r) ∂δ(r − r ) δ(r − r ) − Fμ (r )δαγ , ∂rα ∂rμ

(3.32c)


275

where the elements L(e,u) and L(u,e) are generalized from (3.17) and will be discussed below. As an extension of the index convention introduced after (3.17), we use from here on subscripts α and (α, β) to imply contraction with a vector Aα and matrix Aαβ multiplied from the left, respectively. Conversely, subscripts γ and (γ, ) imply contraction with a vector Aγ and matrix Aγ multiplied from the right. The u-component of the degeneracy requirement L(r, r ) · δS/δx(r )d 3 r = 0 then determines the yet unspecified component L(u,e), with the following expression for the tensor σ, ∂ˆs(ê, F) σ = −Tρ · FT , (3.33) ∂F eˆ with eˆ and sˆ being the entropy densities per unit mass introduced above. The element L(e,u) follows then, again, by antisymmetry condition (2.3b). It should be noted that, at this point, the tensor σ that appears in the elements L(u,e) and L(e,u) is formally not yet identified with the stress tensor σ. It is only after writing down the evolution equations for x as they follow from ∂x(r)/∂t|rev = L(r, r ) · δE/δx(r )d 3 r and the appearance of σ in the divergence term of the evolution of the momentum density, this identification can be made. This is related to the fact that, for a well-chosen set of variables, GENERIC provides a closed set of evolution equations for all variables from which, if so desired, the constitutive relations can be extracted. The final set of evolution equations for finite anisotropic thermoelasticity in an Eulerian setting, according to (2.7), is then obtained as (Hütter and Tervoort, 2008a), ∂u ∂ ∂ = − · (vu) + · σ, ∂t ∂r ∂r ∂ ∂e = − · (ev) + σ : κT , ∂t ∂r ∂F ∂ = −v · F + κ · F. ∂t ∂r

(3.34a) (3.34b) (3.34c)

The stress tensor expression (3.33) is in full agreement with Truesdell and Noll (1992). The standard route to ensure objectivity of the entropy per unit mass sˆ is to assume that it depends on F only through C, which then automatically leads to the objectivity and the symmetry of the stress tensor (Truesdell and Noll, 1992, p. 308). By construction, the antisymmetry (2.3b) and the degeneracy requirement (2.3d) of the Poisson operator (3.32) are satisfied. In addition, it was shown by Hütter and Tervoort (2008a) that the operator (3.32) will satisfy the Jacobi identity (2.3c), which concludes the GENERIC formulation of elasticity.

276


3.4.4. Finite Nonisothermal Anisotropic Elasto-viscoplasticity Hütter and Tervoort (2008b) have shown that rate-dependent plastic deformation can be described as an isochoric relaxation of the deformation gradient, giving rise to an “elastic” deformation gradient Fe . The relaxation behavior of Fe was conveniently presented in terms of the so-called plastic velocity gradient tensor κp , reducing the rate of accumulation of Fe . It should be noted that this definition of Fe does not require a measure of plastic deformation and is free of kinematic assumptions such as a splitting of the deformation into an “elastic” and a “plastic” part. The set of variables (3.29) is, thus, reinterpreted as x = (u, e, Fe ),

(3.35)

where F and Fe have identical reversible kinematics. In addition to the viscoplastic relaxation of Fe , the evolution equations of u and e contain irreversible effects, namely viscous friction, and the flow of heat. However, the latter two have been discussed in the previous example on hydrodynamics and are, therefore, not addressed in detail below. Rather, we concentrate on the formulation of the viscoplastic relaxation of Fe . In the further procedure, we are interested in modeling materials that do not show any change in the specific volume under plastic deformation. This means in turn that the mass density, defined by ρ = ρ0 / det Fe ,

(3.36)

with ρ0 , the mass density in the reference state, is not influenced by the irreversible relaxation of Fe . The generating functionals E and S differ from (3.30) only in replacing F by Fe . Also concerning the reversible dynamics of the variables (3.35), it is sufficient to make the same replacement in the Poisson operator (3.32), and correspondingly also in the stress tensor (3.33) and in the reversible evolution equations (3.34). With regard to the irreversible dynamics, in order to make the volume conservation of the relaxation of Fe explicit, it has proven convenient to introduce projection operator 1 e,−1 e Pαβγ = (δαγ δβ − Fγ Fαβ ). 3

(3.37)

Particularly, since the mass density ρ depends on Fe only through the determinant, and by virtue of the identity ∂(det A) = (det A) AT,−1 , ∂A

(3.38)


277

which holds for any matrix A, one can show that ∂ρ e Pαβγ = 0, ∂Fαβ

(3.39)

which will be beneficial for formulating the friction matrix. Due to (temporary) neglect of viscous stresses and the heat flux, we assume that only the element e e M(F ,F ) of the entire friction matrix is nonzero for which we found (Hütter and Tervoort, 2008b) e

e

¯ μνκλ (r)δ(r − r )Pγκλ (r ). M Fαβ Fγ (r, r ) = Pαβμν (r)

(3.40)

While the degeneracy condition (2.3g) is satisfied for the energy gradient (3.31) by virtue of (3.39), the other requirements (2.3e, 2.3f) translate into conditions on ¯ the fourth-rank tensor , ¯ αβγ = ¯ γαβ , ¯ αβγ Aγ ≥ 0, Aαβ

for all Aαβ .

(3.41a) (3.41b)

If the friction matrix defined in (3.40) operates on the functional derivative of the entropy (3.31) according to (2.7), one obtains the following evolution equation for the elastic deformation gradient: ∂ e 1 dev e,−1 p,c e ¯ μνκλ (σκρ Fλρ ) ≡ −καγ Fγβ . Fαβ = − Pαβμν ∂t T irr

(3.42)

The second equality serves the purpose of establishing the link to the plastic velocp,c ity gradient tensor καβ in the current state, the specific form of which is actually defined through this equality. Particularly, one obtains 1 p,c p,c p,c καβ = κ˘ αβ − (˘κγγ )δαβ , 3 1 p,c e,−1 dev ¯ αρμσ F e,−1 Fσν σμν , κ˘ αβ = ρβ T p,c

p,c

(3.43a) (3.43b)

with κ˘ αβ being the unconstrained and καβ the traceless plastic velocity gradient tensor in the current configuration. Note that the fact trκp,c = 0, which is a ramification of using the projections (3.37), ensures that the mass density (3.36) is unaffected by the plastic deformation. At this point, the guidance of the GENERIC framework is exhausted, and constitutive modeling concentrates on finding appropriate relations for κp,c

278


(or κp,r , see (5.29) below) that fit the material behavior at hand. Specific examples for κp,c and κp,r as used in literature will be discussed in Sections 5.2.5 and 5.2.6. It is important to point out that the GENERIC framework allows for a com¯ (and therefore of κp,c and κp,r ) on the field plicated dependence of the tensor ¯ variables x as long as that dependence is in accord with the conditions (3.41). If is constant, linear viscoelastic behavior is recovered. However, to mimic the occur¯ must be selected to be a highly nonlinear function of the rence of a yield stress, Cauchy stress tensor, for example, in the form of an Eyring viscosity (Krausz and Eyring, 1975). In this case, the resulting equations lead to nonlinear viscoelastic behavior that is virtually indistinguishable from the existence of a rate-dependent yield surface. Including viscous stresses and heat flux, the full set of evolution equations (2.7) assumes the form ∂u ∂ ∂ = − · (vu) + · σt, ∂t ∂r ∂r ∂ ∂ q ∂e = − · (ev) + σ t : κT − ·j , ∂t ∂r ∂r ∂Fe ∂ = −v · Fe + κ − κp,c · Fe , ∂t ∂r

(3.44a) (3.44b) (3.44c)

with v = u/ρ being the velocity field, κ = ∂v/∂r, jq the heat flux, and κp,c the traceless plastic velocity gradient tensor in the current state (3.43). The total Cauchy stress tensor, σ t , is the sum of a viscous contribution, arising from fluid-like relaxation of the momentum density u, and an elastic contribution. The viscous contribution would be determined by the total velocity gradient as in (3.23a), but is often absent or neglected in elasto-viscoplastic deformation. The elastic contribution to the total Cauchy stress tensor was found to assume the form ∂ˆs(ê, Fe ) σ = −Tρ · Fe,T . (3.45) ∂Fe eˆ While constructing the friction matrix M, as in the case of hydrodynamics, it was found that heat diffusion is driven by the gradient in temperature through a second-order heat conduction tensor. Purely viscous stresses that occur due to the velocity gradient κ could be described with a fourth-rank viscosity tensor. Interestingly, it was found that plastic deformation, described as relaxation of the elastic deformation gradient Fe , is driven by the derivative of the free energy with respect to the isochoric elastic deformation gradient. A traceless plastic velocity gradient κp,c used to conveniently represent the relaxation of Fe , in turn, specified that the unconstrained plastic velocity gradient tensor κ˘ p,c is driven by the deviatoric part of the Cauchy stress tensor. In this respect, it is interesting to rewrite the entropy


279

production (3.27) that upon using the evolution equations (3.44) assumes the form ρσ = jq ·

∂ 1 1 1 + σ v : κ + σ : κp,c ≥ 0, ∂r T T T

(3.46)

which shows the force–flux pairs (∂T −1 /∂r, jq ), (κ, σ v ), and (σ, κp,c ) for heat conduction, viscous flow, and viscoplastic flow, respectively. Particularly, the last pair surfaced in the constitutive equation (3.43) for the plastic velocity gradient tensor. Similar to the hydrodynamic example in the previous section, we have referred several times to the knowledge about the final evolution equations when constructing the building blocks, particularly as far as the Poisson operator is concerned. This situation will change considerably when deriving the above evolution equations by way of coarse graining from the microscopic level of description in Section 5.2. 4. GENERIC Framework. II. Methodology of Coarse Graining

4.1. Introduction A particular feature of the GENERIC framework is that it can be used to formulate the dynamics of a system on different levels of description, for example, in terms of the reversible Hamiltonian point mechanics and dissipative macroscopic field theories, as illustrated above. Obviously, the four building blocks E, S, L, and M differ between the different levels. However, there are abstract procedures to relate them, and the reader is referred to Öttinger (1998, 2005, 2007) for the full details. Below, we briefly introduce those concepts and relations that are of particular relevance for this article. However, before going into the specifics of constructing the individual building blocks on a coarse level in terms of the more microscopic details, we comment on an important prerequisite for a successful coarse graining, namely the clear separation of time scales. The separation of characteristic time scales between the different levels of description is of paramount importance in systematic coarse graining techniques. Figure 4.1 illustrates the setting for three levels of description. We denote by L0 the microscopic level of discrete particles (atoms and molecules) and purely reversible dynamics described by Hamiltonian point mechanics. As an illustrative example, we mention a colloidal (mm sized) particle immersed in a solvent, where the dynamics of all the molecular constituents both of the colloidal particle and of the solvent is described explicitly. On a coarse-grained level L1 , that system can be modeled as a single inert colloidal particle, while the solvent is taken into account only through a Brownian force and a friction force acting on the colloidal particle. That well-known coarse-grained level clearly highlights that the elimination of the

280


y

z

x

t

t

p(tc)

t

Irrev. effects on L2 Irrev. effects on L1 and L2

E S

S2

(a.u.) E S1

S0 tc L0

1

L1

tc2

L2

tc, c level

Fig. 4.1 Illustration of coarse graining between different levels of description, Li . The greyarea indicates the distribution of characteristic time scales, p(τc ). The regions around τc1 and τc2 with p(τc ) 0 are indicative of a clear separation of time scales. While the energy E is (almost) constant when represented on the different levels, the entropy S increases drastically upon coarse graining. A reduction in degrees of freedom from fast into slow variables brings about the emergence of irreversible effects on the coarse-grained level. The symbol c denotes a characteristic length scale.

fast degrees of freedom of the solvent primarily leads to interesting irreversible effects. The derivation of such phenomena that arise as a result of coarse graining is our primary interest and must be an essential outcome of a successful coarse graining scheme. As a third level of description L2 , one can consider the continuum field theoretic level, for example, in the sense of an effective medium theory taking into account the different constituents in a very coarse fashion. A similar distinction between different levels of description can also be made in the field of solid mechanics (see Table 4.1). For example, in crystalline materials, the level L0 is characterized by the dynamics of the individual atoms, while level L2 is described by macroscopic field theories of solid mechanics, taking into account elastic and plastic effects in a phenomenological manner. However, particularly in order to understand better the phenomena occurring during plastic deformation, the concept of dislocations is essential (Orowan, 1934; Von Polanyi, 1934; Taylor, 1934; Nabarro, 1967; Hirth and Lothe, 1982). In the scheme illustrated in Fig. 4.1,


281

Table 4.1 Examples of systems with different levels of description. Details are discussed in the text. Suspension

Solid Mechanics

L0

Atoms of the large particle, Atoms of the solvent

Atoms or molecules

L1

Rigid Brownian particle (no explicit solvent)

Dislocations

L2

Hydrodynamic fields (macroscopic)

Fields of deformation (macroscopic)

this translates into choosing for L1 the level constituted by the dislocations themselves. Since dislocations have irreversible contributions in their evolution, one concludes that irreversible effects emerge as a result of the coarse graining from L0 to L1 . However, using dislocations for explaining the mechanics of crystalline solids on the macroscopic scales corresponds to coarse graining from L1 to L2 . In general, if one aims at establishing the links between such different levels of description by projection operator techniques (Grabert, 1982), one observes that the clear separation of time scales (as indicated by a vanishing distribution p(τc ) of characteristic time scales in Fig. 4.1) is crucial. While we do not delve further into this issue, it is pointed out that checking that criterion in concrete examples can prove to be rather difficult (see also comment at the end of Section 4.4). In what follows, we concentrate on coarse graining from the microscopic level L0 described by Hamiltonian point mechanics to a coarser level (L1 or L2 ), for simplicity. For the proper steps and procedures to coarse-grain further from an already coarse-grained description L1 , the reader is referred to Öttinger (2005).

4.2. Ensembles Consider a physical system that can be described to different degrees of detail (see Fig. 4.1), for example, on a microscopic (reversible) level L0 , on a mesoscopic level L1 , and on a macroscopic level L2 . For introducing the concepts of coarse graining from the microscopic level to another level (be it L1 or L2 ), we shall denote the microscopic degrees of freedom on L0 by z and the coarse-grained degrees of freedom by x, irrespective of whether they are defined on level L1 or L2 . For example, z represents the positions and momenta of all N particles, (3.1), and x can include field variables defined at every position r in space, for example, the mass density ρ(r) or the momentum density u(r). However, the microscopic particles move rapidly in and out of the volume element d 3 r around r, and the interactions occur on rapid time scales too fast compared to what one aims at capturing in the coarse variables x. Therefore, the instantaneous values of x

282


expressed in terms of the microscopic variables z, denoted by x (z), need to be averaged in order to arrive at the spatially smoothed and slowly evolving variables x. To that end, one needs the concept of an ensemble and the corresponding distribution of microstates, ρx (z), that is normalized in the microscopic phase space, (4.1) ρx (z)d 6N z = 1. Similar to equilibrium statistical mechanics (Lifshitz and Pitaevskii, 1980a; Le Bellac et al., 2004; Frenkel and Smit, 2002), there are different kinds of ensembles, depending on whether the values of the variables x are reproduced by the microstate z exactly or only on average, which leads either to generalized microcanonical ensembles or to generalized canonical ensembles. Ensembles of mixed character can also be used. While the generalized microcanonical ensemble is often useful for demonstrating abstract relations and formal results, the generalized canonical ensembles are often more straightforward to use in particular applications. In the canonical setting, Lagrange parameters λ are introduced to control the averages of the coarse-grained variables, x. Whichever ensemble is studied, the coarsegrained variables x are related to their instantaneous microscopic counterparts x (z) through xi = ρx (z)xi (z)d 6N z ≡ xi (z) x , for all i, (4.2) where we have introduced the notation . . .x to indicate the average with respect to the distribution function ρx (z) of microstates. Maximizing the entropy S = −kB ρx (z) ln ρx (z)d 6N z under the constraints (4.1, 4.2), the distribution function in the generalized canonical ensemble can be shown to assume the form 1 ρx (z) = exp − λi xi (z) , (4.3) Z i

where the normalization constant is the partition function Z = exp − λi xi (z) d 6N z.

(4.4)

i

Based on the partition function (4.4), the averages with respect to the distribution function (4.3) can be written as xi = −

δ ln Z . δλi

(4.5)


283

This relation can be used to eliminate the Lagrange parameters λ in favor of the variables x, and therefore the distribution function ρx (z) depends indeed on the coarse-grained variables x, as the notation suggests. In order to make sure that the preference for a particular ensemble in a specific application does not bias the final results, the equivalence of the ensembles must be demonstrated. It can be shown that the different ensembles are equivalent if the fluctuations of the variables xi are small, that is, x (z) − xi x (z) − xk |xi | |xk | , i k x or, expressed in terms of the partition function, 2 δ ln Z δ ln Z δ ln Z , δλ δλ δλ δλ i k i k

(4.6a)

(4.6b)

for all pairs (i, k). In the case of field variables x(r), the values at the different positions r are (in principle) independent. One can imagine that, for discretized space, each field variable is represented by a vector of its values at the discrete positions. With this in mind, it becomes clear that (i) the distribution function ρx (z) is a functional rather than a function of x, (ii) the exponent in (4.3) includes a discrete summation over the fields as well as a continuous integration over the positions r, and (iii) the relation (4.5) indeed involves a functional derivative rather than a partial derivative. This convention of neglecting the integration over r is followed for the rest of this Section 4 to simplify the notation.

4.3. Generators The total amount of energy of the system on the microscopic level consists of kinetic and interaction energies. If the set of coarse-grained variables x is chosen suitably, then all different kinds of energy are well represented on the coarsegrained level (see Fig. 4.1). Hence, one expects E(x) = E0 (z)x ,

(4.7)

where E0 is the microscopic Hamiltonian. While (4.7) indicates that the average amount of energy is independent of the level of description, the situation is dramatically different for the entropy, the fundamental reason being that the entropy is related to the number of microstates that correspond to a given coarse-grained state. Certainly, the higher the degree of coarse graining, the more microscopic information is lumped together, leading to higher entropy, as illustrated in Fig. 4.1.

284


To be more precise, it can be shown that the entropy S on the coarse-grained level can be expressed as S(x) = kB ln Z +

λi xi ,

(4.8)

i

where Z is the partition function (4.4) that counts the number of available microstates. While the right-hand side of this equation is, in principle, a function of the Lagrange parameters λ, one can use the relations (4.5) to express the entropy in terms of the coarse-grained variables x. For the interpretation of the Lagrange parameters λ, it is instructive to note the identity δS(x) = kB λi , δxi

(4.9)

which has been derived on the basis of (4.8) and (4.5). In the example of nonisothermal hydrodynamics discussed in Section 3.3, this allows to interpret the Lagrange parameters as λρ = −μ/(kB T ), λu = 0, and λe = 1/(kB T ), with μ being the chemical potential. For the modeling of macroscopic elasto-viscoplasticity presented in Section 3.4, one obtains λu = 0, λe = 1/(kB T ), and λF = kB−1 ∂s/∂F. While most of these expressions are known from equilibrium thermodynamics, we point out that the control parameter for the deformation gradient, λF , is closely related to the stress tensor (3.45).

4.4. Operators Since the Poisson operator L describes that part of the evolution that is under mechanistic control, one expects that L on the coarse-grained level is closely related to the mechanistically controlled evolution on the microscopic level as given by Hamiltonian point mechanics. Indeed, one can show that ∂xi (z) ∂xk (z) Lik (x) = · L0 · , (4.10) ∂z ∂z x with L0 being the Poisson operator on the microscopic level, that is, the one given by (3.3) for a system of N point particles. L0 is contracted with the z in the denominators. An interpretation of the above equation can be given as follows. If x (z) was invertible and in the absence of the averaging, the relation (4.10) would just correspond to a standard transformation of variables from z to x . However, since the mapping from the microstates z to x is not invertible, the average over microstates z that correspond to the coarse-grained state x is required.


285

The separation of time scales between the different levels of description has so far not come into play when constructing the three building blocks E, S, and L. This is in sharp contrast to the derivation of the friction matrix M to be discussed in the following. In view of the situation illustrated in Fig. 4.1, there are two fundamentally different origins of irreversible effects on a specific level (L2 ). First, irreversible effects on one level (L1 ) are re-expressed on the next coarser levels (e.g., L2 ). An example of this type is given by a suspension of colloidal particles that experience Brownian and friction forces. The description of such a suspension on a coarser, purely continuum level will also represent some aspects of the friction force. Similarly, the irreversible contributions to the dynamics of dislocations in crystalline solids will also surface again in the macroscopic continuum theory of solid mechanics. A second type of irreversible effects on level L2 captures fast dynamics that is explicitly resolved on levels L0 and L1 , but that are too rapid (i.e., fluctuating) to be described on level L2 . In other words, some dynamic effects with a characteristic time scale smaller than τc2 will be represented on level L1 as reversible terms, while on level L2 , they are expressed as irreversible contributions to the evolution equations. Such an emergence of irreversible effects also occurs when coarse graining from level L0 to L1 in the presence of effects with characteristic time scales below τc1 . As an example, we consider again a large colloidal particle immersed in a sea of much smaller host particles. That system is well described by Hamiltonian point mechanics for all particles on L0 . However, on the coarse scale L1 , upon neglect of the host particles, the large particle experiences Brownian and friction forces, both relicts of the collisions with the large number of rapid host particles.4 Analogously, in solid mechanics, the transition from the dynamics of atoms to the dynamics of dislocations brings about irreversible effects, which are often described by diffusivities and jump rates of dislocations or kinks. These statements about coarse graining support our initial comment about the separation between reversible and irreversible contributions to the evolution equations (2.3a): the former represents what is under mechanistic control, while the latter represents the “rest.” It is particularly the emergence of irreversible effects upon coarse graining, which we concentrate on in the following. Under the assumption of time scale separation between the different levels, the projection operator method (Grabert, 1982) has been used (i) to relate a coarse level of description with the microscopic purely reversible dynamics and (ii) to establish the transition between two different levels of coarse graining, in the context of 4

The difference in the representation of the physics on the different levels is reflected in the simulation methods to be employed on each level. While molecular dynamics simulations describe the microscopic Hamiltonian mechanics, there are a variety of methods to simulate a system on the intermediate, coarsegrained level, such as Brownian dynamics and dissipative particle dynamics simulations (Frenkel and Smit, 2002; Öttinger, 1996).

286


GENERIC (see Öttinger (1998, 2005)). Rather than writing the corresponding result of the projection operator procedure in its full form, we here summarize the result in a symbolic notation, which is sufficient for our purpose. Let the quantity ˙ fx (z(t)) denote the rate of change in xi at time t according to the fast dynamics i of the microscopic degrees of freedom, z, projected onto the space perpendicular to x (z). Then, one can write for the elements of the friction matrix (Öttinger, 1998, 2005) τ 1 ˙ fx (z(t)) ˙ fx (z(0)) dt, Mik (x) = (4.11a) i k x kB 0 that is, the integral of the time correlation function between the rapid fluctuations in the quantities xi (z) and xk (z). In (4.11a), the upper integration limit τ is the time scale intermediate between the characteristic time scales of the fine grained and the coarse-grained levels of description (e.g., τc1 or τc2 in Fig. 4.1). Since the separation of time scales is assumed to hold in the above procedure, the time correlation between the fast degrees of freedom in (4.11a) has decayed completely for t = τ, and at the same time, the slow (coarse-grained) variables x = x (z)x practically do not change over the entire interval [0, τ]. The average ·x in (4.11a) indicates that the (fast) microscopic trajectories must be consistent with the slowly evolving, coarse-grained state x at t = 0. Assuming that the correlation function decays sufficiently fast, one can rewrite (4.11a) in the form 1 (4.11b) [1 + ε(xi )ε(xk )]Mik (x) = τ fxi (z)τ fxk (z) , x kB τ with ε(xj ) = ±1 depending on the parity of xj under time reversal, and with the increment τ fxj (z) = fxj (z(τ)) − fxj (z(0)) of the fluctuations in the quantity xj over the time interval [0, τ]. The expression (4.11a) for the elements of the friction matrix is a generalization of the well-known fluctuation–dissipation theorems (de Groot and Mazur, 1962; Kubo et al., 1991; Evans and Morriss, 1990; Öttinger, 2005), also known as Green– Kubo relations. As two particular examples of the latter, we mention the zero shear-rate viscosity expressed in terms of the time correlation of the fluctuations in the shear stress, and the thermal conductivity related to the time correlation of the fluctuations in the heat flux. Written in the form (4.11b), the friction matrix is recognized as a generalization of the formula to express the spatial diffusion coefficient in terms of the mean square displacement for diffusing particles. In principle, the friction matrix can be determined once the fluctuations of the quantities x as well as their self- and cross-time correlations are known, according to (4.11). There are two fundamentally different ways to apply the microscopic expression for the friction matrix in practical applications. According to the first


287

strategy, one starts with calculation of the rapid changes in the quantities x (z) according to the microscopic evolution (˙z) by way of the chain rule and projects that result to the space perpendicular to x . With these microscopic expressions for the rapid changes, one can go about determining their time correlation. However, analytical closed-form calculations are increasingly difficult the more interesting the studied systems, and one can then resort to computer simulations. Using molecular dynamics simulations, for example, the shear viscosity (Smith and van Gunsteren, 1993), the bulk viscosity (Hoheisel et al., 1987), and the thermal transport coefficients of liquids (Hoheisel and Vogelsang, 1988) have been determined based on the concept of time-correlation functions. The reader is also referred to Section 6.5.5 of Allen and Tildesley (1987) for details on this method. The second strategy for benefiting from the relation (4.11) between fluctuations and irreversible effects consists of making an ansatz for the structural form of the fluctuations. One can assume that the evolution equations for the rapid quantities x (z) are similar in structure to the evolution equations of their coarse-grained counterparts x, in the spirit of Onsager’s regression hypothesis. This hypothesis states that the fluctuations about the equilibrium state decay, on the average, according to the same laws that govern the decay of coarse-grained deviations from equilibrium (Kubo et al., 1991; Evans and Morriss, 1990; Öttinger, 2005). Onsager’s regression hypothesis has been applied, for example, in Jelic´ et al. (2006) on electromagnetic systems to derive that the well-known Ohmic resistance is just one of the three fundamentally different irreversible effects in macroscopic electromagnetic systems. This latter strategy will also be employed in the applications below. The above procedure defines the GENERIC building blocks of energy E, entropy S, and the two operators L and M. Given the above definitions of the coarse-grained building blocks, it can indeed be shown that the conditions imposed by the GENERIC framework (2.3b, 2.3d–2.3g) are satisfied also on the coarsegrained level of description. Therefore, these conditions need not be checked explicitly in any particular application. Only, the Jacobi identity (2.3c) needs special consideration. For details, the reader is referred to Öttinger (1998, 2005). We now return briefly to the question of how to verify whether time-scale separation holds for a specific system of interest. To that end, one can depart from considering correlation functions as they appear in the microscopic expression for the friction matrix (4.11a). Our notion of time-scale separation implies that all characteristic decorrelation times of the microscopic quantities are substantially smaller than the characteristic time scales for the coarse-grained variables. Therefore, the time integral in (4.11a) is constant with respect to the upper integration limit τ for a large range of τ-values. Conversely, for the same range of τ-values, the average on the right-hand side of (4.11b) must be linear in τ. The insensitivity of the friction matrix (4.11) with respect to the time scale τ over a certain range

288


is, thus, an indication of time-scale separation and has been used, for example, in Section 8.4.6 of Öttinger (2005). For effects due to a finite ratio between the fast and slow time scales, the reader is referred to Geigenmüller et al. (1983a,b).

5. Applications of the Coarse-graining Procedure

5.1. From Hamiltonian Point Mechanics to Hydrodynamics As a first application of the above coarse-graining scheme, we reconsider the case of nonisothermal compressible hydrodynamics discussed in Section 3.3 (see also de Pablo and Öttinger (2001) for a slightly different treatment). Particularly, we establish the link between the microscopic level L0 and the macroscopic level L2 (see Fig. 4.1 and Table 4.1). As a first step, we seek to express the field variables (3.12) in terms of the microscopic degrees of freedom (3.1), that is, the particle positions ri and momenta pi . This is achieved by the definitions (Kreuzer, 1981; Evans and Morriss, 1990; Irving and Kirkwood, 1950) ρ (z; r) =

N

mi δ(r − ri ),

(5.1a)

pi δ(r − ri ),

(5.1b)

i=1

u (z; r) =

N i=1

e (z; r) =

N i=1

⎞ 1 1 ⎝ [pi − mi v(ri )]2 + (rij )⎠ δ(r − ri ), (5.1c) 2mi 2 ⎛

j=i

with rij = ri − rj , and N the total number of particles. The velocity field v occurring in (5.1c) is related to the average mass and momentum densities defined in (5.2) below, v = u/ρ. Note that the internal energy density accounts for the particle momenta only as measured relative to the average streaming velocity. Together with the interactions, e is, thus, indeed an internal energy density, not accounting for the kinetic energy density due to the overall motion of the entire fluid element. The coarse-grained variables x are related to the instantaneous values (5.1) through the averages ρ(r) = ρ (z; r) x , (5.2a) u(r) = u (z; r)x ,

(5.2b)

e(r) = e (z; r)x .

(5.2c)


289

Using the expressions (5.2), it can indeed be shown that the macroscopic expression for the energy (3.13a) coincides with the average of the microscopic energy, E0 (z)x , where E0 is given by the right-hand side of (3.2a). As far as the entropy is concerned, we refrain from deriving it explicitly. Rather, in order to keep this treatment concise, we assume that the macroscopic entropy can be written in the form (3.13b) with an entropy density per unit volume s(ρ, e). Using the local equilibrium assumption discussed earlier, the entropy density can be derived from the equilibrium entropy function. Since the computation of the thermodynamic potential for a given microscopic Hamiltonian system is a classical topic in equilibrium statistical mechanics, we do not examine this aspect any further, and rather refer the reader to the appropriate literature on equilibrium thermodynamics (e.g., Lifshitz and Pitaevskii, 1980a; Le Bellac et al., 2004, and for a concise introduction in the context of simulations Frenkel and Smit (2002)). The Poisson operator L for nonisothermal hydrodynamics can be derived on the basis of (4.10). With the aid of (3.3) and (5.1), its matrix elements can be written in the form (see also (3.5)) N ∂xi (z; r) ∂xk (z; r ) ∂xi (z; r) ∂xk (z; r ) Lik (x)(r, r ) = · − · .(5.3) ∂rn ∂pn ∂pn ∂rn x

n=1

For illustration, we explicitly derive the elements L(ρ,u) and L(u,u) . With the definitions (5.1a, 5.1b), one finds

L

(ρ,u)

=

N

∂δ(r − rn ) · 1δ(r − rn ) mn ∂rn

n=1

=

N

∂δ(r − r ) ∂δ(r − r ) mn δ(r − rn ) x = ρ(r ) , ∂r ∂r

n=1

L

(u,u)

=

N

∂δ(r − rn ) ∂δ(r − rn ) δ(r − rn ) − δ(r − rn ) pn pn ∂rn ∂rn

n=1

=

x

(5.4a) x

N n=1

N ∂δ(r − r ) ∂δ(r − r ) pn δ(r − rn )x pn δ(r − rn ) x − ∂r ∂r

∂δ(r − r ) ∂δ(r − r ) u(r), = u(r ) − ∂r ∂r

n=1

(5.4b)

290


which indeed correspond to the previous expressions in (3.17). Calculating the other contributions in a similar way, one can show that (3.17) is recovered after replacing −p1 by the stress tensor σ(r) = σ (z; r)x ,

(5.5a)

with the microscopic expression (Kreuzer, 1981; Evans and Morriss, 1990; Irving and Kirkwood, 1950), ⎛ ⎞ N ∂ 1 1 ⎝− [pi − mi v(ri )] [pi − mi v(ri )] + ⎠δ(r − ri ) , σ (z; r) = rij mi 2 ∂rij j=i

i=1

(5.5b) consisting of two contributions. The first term is due to the motion of the particles relative to the average (macroscopic) velocity field (see Zhou, 2003, for a related, rather recent, controversy), while the second term originates from the particle interactions. Since the degeneracy requirement (2.3d) must be satisfied after coarse graining, as discussed earlier, one concludes that the stress tensor assumes the form σ = −p1 with pressure p given by (3.15c).5 As the Poisson operator obtained on the basis of (5.3) collapses with (3.17), it also satisfies the GENERIC properties (2.3b–2.3d). The structure of the friction matrix is studied by using Onsager’s regression hypothesis discussed earlier. Particularly, with the slow evolution equations (3.22) of the nonisothermal hydrodynamics, we make the following ansatz for the fluctuating changes (see also Lifshitz and Pitaevskii, 1980b) ˙ fρ (z; r) = 0 , ˙ fu (z; r) =

(5.6a)

∂ · σf , ∂r

˙ fe (z; r) = σ f : κ −

(5.6b) ∂ q,f ·j , ∂r

(5.6c)

with σ f and jq,f being the fluctuating contributions to the stress tensor and the heat flux, respectively. Note that the of u and e are such that they fluctuations ˙ fx d 3 r = 0 for an isolated system. conserve the total energy, that is, (δE/δx) · Furthermore, it has been assumed that the mass density does not fluctuate, that is, it is a purely slow variable. The ansatz (5.6) for the fluctuations is also supported by an analysis using projection operator methods (Ilg, 2008, private communication). 5 Another, more complicated, argument in favor of σ being isotropic uses specific properties of the distribution function ρx (z) and employs the rotational symmetry of the interactions.


291

If cross-correlations between σ f and jq,f are neglected, the friction matrix, τ 1 ˙ fx (z(t); r) ˙ fx (z(0); r ) dt, Mik (x)(r, r ) = (5.7) i k x kB 0 assumes the form (3.20) after making the identifications τ 1 f f σαβ ηαβγ (r) T(r) δ(r − r ) = (z(t); r)σγ (z(0); r ) dt, (5.8a) x kB 0 τ 1 λqμν (r) T 2 (r) δ(r − r ) = jμq,f (z(t); r)jνq,f (z(0); r ) dt. (5.8b) x kB 0 These expressions are in full agreement with the classical results of linear response theory (Evans and Morriss, 1990; Kubo et al., 1991), and one can also show that the conditions (3.21) are fulfilled. The following lessons can be learned from deriving the friction matrix based on Onsager’s regression hypothesis: • The classical fluctuation–dissipation relations in terms of the current–current correlations are contained in the generalized form (4.11). • The form of M in the purely macroscopic treatment (3.20) implies that the fluctuations are only correlated locally in space, that is, long-ranged correlations are absent. • Using the form (3.20) implies neglect of cross-correlations between the fluctuations in the stress tensor σ f and the heat flux jq,f . • In view of the viscosity tensor (3.24a) for isotropic conditions, one obtains statements about the absence of correlations between different components of the stress tensor.

5.2. From Hamiltonian Point Mechanics to Elasto-viscoplasticity 5.2.1. Microscopic Expression for the Deformation Gradient The goal of this example is to study macroscopic elasticity and elastoviscoplasticity from a completely different perspective compared to what has been presented earlier in Section 3.4. Rather than giving a self-contained description on one level of detail, we aim at deriving the corresponding macroscopic evolution equations (level L2 ) based on microscopic principles (level L0 ) (see Fig. 4.1 and Table 4.1). As discussed in detail in Section 3.4, the set of variables (3.29) consisting of the momentum density u, the internal energy density e, and the deformation gradient F is suitable to describe macroscopic elasticity. In particular, in comparison to nonisothermal hydrodynamics, the mass density is replaced by the deformation gradient that accounts for the changes both in volume and in shape.

292


To start, we mention that the microscopic expressions for the momentum density and the internal energy density have been specified in the previous example, namely (5.1b) and (5.1c), respectively. We now seek to express the macroscopic deformation gradient in terms of the positions of the constituent atoms or molecules, in summary called particles in the following. To that end, we first note the following. Given a particle i and three other particles in the vicinity of i with indices j1 , j2 , j3 , one can introduce the three difference vectors rjk i = rjk − ri . These difference vectors can not only be measured in the actual configuration of particles but also be defined in some initial (reference) configuration, denoted by rj0k i .6 If these three vectors in the reference configuration are linearly independent, Dij0 1 j2 j3 = det[rj01 i rj02 i rj03 i ] = 0, then F,ij ˆ 1 j2 j3 (z; r) =

3

rjk i rˆ j0k i

(5.9)

k=1

defines the deformation gradient based on the quadruple (i, j1 , j2 , j3 ) of particles. The quantities rˆ j0k i are vectors dual to rj0l i in the initial configuration, that is, rˆ j0k i · rj0l i = δkl . The fact that (5.9) indeed defines a local deformation gradient can be seen as follows. Any vector a0 in the initial state can be written in the form a0 = 3k=1 ak rj0k i , which is mapped by application of F,ij ˆ 1 j2 j3 (z; r) to the vector 3 a = k=1 ak rjk i in the current configuration. This being said, we can introduce a macroscopic measure of deformation ˆ (5.10a) F(r) = Fˆ (z; r) x , with Fˆ (z; r) =

N i=1

fij1 j2 j3

j1 ,j2 ,j3

j1 ,j2 ,j3

3

0 k=1 rjk i rˆ jk i

fij1 j2 j3

δ(r − ri ).

(5.10b)

In this expression, the function fij1 j2 j3 is a weighting factor to make sure that only those quadruples (i, j1 , j2 , j3 ) contribute to the sum that satisfy three conditions. First, fij1 j2 j3 depends on the determinant Dij0 1 j2 j3 to ensure that the triplet of connector vectors is linearly independent and serves as a suitable set of base vectors. Second, in the reference configuration, the particles jk must be located not too close to the particle i, that is, 1 |rij0 k | for some cut-off length 1 > 0, for the following reason. At finite temperature, the particles exert a fast vibrational motion. If particles jk and i were adjacent, such irregular displacements 6

The importance of microscopic reference states in crystalline and amorphous solids has been discussed in detail by Alexander (1998).


293

would lead to significant spurious contributions in the microscopic strain. To minimize such undesirable effects, the cut-off length 1 is introduced. However, as the third condition, we are interested to obtain significant contributions only if the particles jk and i are separated less than 2 , |rij0 k | 2 . Here, 2 is some characteristic averaging length over which relative displacements are considered for the calculation of the microscopic deformation gradient, the latter being local on the macroscopic scale. The fact that the weight fij1 j2 j3 depends on the initial particle separations rather than on the current ones is a convenient choice to simplify the further discussion, but more elaborate cases can be studied. The expression in the parentheses in (5.10b) is the average deformation gradient based on all (viable) triplets (j1 , j2 , j3 ) around particle i. The Dirac delta function δ(r − ri ) is introduced to arrive at a measure of deformation around r. However, the so introduced delta function in turn will lead to Fˆ being a deformation gradient density (similar to (5.1a) and (5.1b) being mass and momentum densities, respectively), rather than a deformation gradient. To illustrate this point, assume the case of a purely ¯ affine deformation where F,ij ˆ 1 j2 j3 (z; r) is a complete constant Fˆ , in which case, N ¯ˆ δ(r − ri ). The aspect of Fˆ being a density-like one obtains ˆ (z; r) = F

F

i=1

quantity is discussed in more detail below. The expression (5.10b) for the microscopic deformation is different from other procedures adopted in literature. For example, Goldhirsch and Goldenberg (2002) provide a microscopic expression for the displacement field as a link between the fine and the coarse levels of description, from which the linear strain field is then derived. Falk and Langer (1998) approximate the deformation of small clusters of particles over a small time interval by a best-fit uniform strain, and particle displacements deviating from that uniform strain field signify deviations from affine deformation. Using their procedure for the entire time interval between the reference state and the current state, one can define the deformation gradient density alternatively to (5.10b) as

(z; r) FL Fˆ

=

N i=1

j

0 · Y −1 fij rji rji i f j ij

δ(r − ri ),

(5.11)

with Y i being a matrix that depends on the structure around particle i in the reference configuration. One observes that the occurrence of the current particle positions is strikingly similar in (5.10b) and (5.11), which will be of relevance particularly when discussing the reversible dynamics in Section 5.2.3. For an overview and discussion of microscopic definitions of strain tensors that are based on best-fit and equivalent continuum methods, respectively, the reader is referred to Bagi (2006). Along different lines, Aubouy et al. (2003) introduce the so-called

294


texture tensor in terms of an appropriate average over the symmetric dyadic product rij rij , with rij the connector vector between particles i and j. Subsequently, they measure the amount of deformation in the material by comparing the average of the dyadic product in the deformed state with the average in an isotropic reference state. Note that this contrasts to our definition of the deformation gradient density Fˆ and to the procedure of Falk and Langer (1998), in both of which the current and initial state are related not on average but rather configuration-wise. Other measures of microscopic deformation are introduced in literature with specific applicability to crystalline structures (e.g., see Buehler et al. (2004)), which is based on the work of Zimmerman (1999). To help the interpretation of the microscopic expression (5.10b), and in view of the further developments, we briefly discuss which quantities in (5.10b) are dynamic and which are static. In accord with conventional approaches to elasticity, the reference state is fixed, and hence the corresponding particle positions ri0 remain constant, while the current positions ri change in time. In contrast, there are two different ways to account for plastic deformation. This irreversible process can be described exclusively in terms of dynamics either in the current state or in the reference state (see also the related comments ‘Alternative Interpretations of Fluctuations’ at the end of Section 5.2.4). We expand in more detail on this circumstance in the Section 6.

5.2.2. Generators Concerning the two generators (3.30), the total energy E has been discussed in the previous example. The form of the entropy density s(e, F) is here assumed to be a given function since its derivation can be performed in the context of classical equilibrium thermodynamics and does not lead to any deep insights about the dynamics in which we are mainly interested here.

5.2.3. Poisson Operator—Reversible Dynamics In order to calculate the reversible contributions to the evolution equations of x, the elements of the Poisson operator must be constructed. Since the reversible effects are dominated by the velocity field and by virtue of δE/δu = v, we are again focusing on the momentum column of the Poisson operator. The transport of Fˆ due ˆ to the velocity field is then determined by L(F,u) . Using (5.3) with the momentum density (5.1b) and the deformation gradient density (5.10b), one obtains after some calculations analogous to (5.4) the result (see Appendix B) ˆ L(Fαβ ,uγ ) (r, r ) = Fˆ αβ (r )

∂δ(r − r ) ∂δ(r − r ) ˆ μβ (r)δαγ + F , ∂rγ ∂rμ

(5.12a)


295

and for the antisymmetric contribution in the Poisson operator, ˆ L(uα ,Fγ ) (r, r ) = −Fˆ γ (r)

∂δ(r − r ) ∂δ(r − r ) − Fˆ μ (r )δαγ . (5.12b) ∂rα ∂rμ

(Note that the same elements also hold for the Falk–Langer-type expression (5.11) as can be shown with calculations analogous to the ones in Appendix B). According to (2.7) and with δE/δu = v, the evolution equation ∂Fˆ αβ (r)/∂t = (Fˆ ,u ) L αβ γ (r, r )vγ (r )d 3 r assumes the form ∂ ˆ ∂ F = − · vFˆ + κ · Fˆ , ∂t ∂r

(5.13)

with κ the transposed velocity gradient defined in Section 3.3. The fact that the second index of Fˆ is not contracted with any measure of the velocity gradient goes back to the dual vectors rˆ j0k i in the reference configuration being purely static during the reversible dynamics.7 We note that the evolution equation (5.13) for Fˆ differs from (3.34c) for F by the, ∂ ˆ Since the latter is proportional at first sight unexpected, contribution −( ∂r · v)F. to the rate of isotropic expansion, we examine in the following discussion the behavior of Fˆ and F under an isotropic dilation in the current conformation by a factor λ. On the one hand, based on the definition F = ∂r(R, t)/∂R, one finds for the strained deformation gradient F[λ] = λF[λ=1] . On the other hand, we consider the deformation gradient density (5.10). If one assumes a dilation around r = 0 and uses the mapping ri[λ] = λri for all particle positions, one obtains [λ] = ˆ F

λ−2 [λ=1] , where we have made use of the fact that δ(λri ) = δ(ri )/λ3 , and thus Fˆ Fˆ [λ] = λ−2 Fˆ [λ=1] . The different scaling between F and Fˆ with respect to dilation ˆ det F, ˆ with a constant in the current configuration leads to the relation F = ϕF/

dimensional prefactor ϕ. Based on (5.13), one can indeed show that the quantity ˆ det Fˆ evolves in time according to (3.34c). The relation between F and Fˆ ϕF/ and their evolution equations are summarized in Table 5.1. Along similar lines, one can show how to extract from Fˆ the constrained deformation gradient F˜ (with det F˜ = 1) and the mass density ρ (see Table 5.1). To derive the corresponding evolution equations, one makes use of the identity (3.38). In summary, we observe that all quantities used for modeling the deformation of an elastic material can be ˆ derived from the microscopically defined deformation gradient density F. For the further construction of the Poisson operator L according to (5.3), we note the following. First, one can prove L(e,e) = 0 as in the hydrodynamic case 7 This situation changes upon consideration of viscoplastic deformation, as explained at the end of the Section 6.

296

M. Hütter and T. A. Tervoort Table 5.1

Summary of the relation between the deformation gradient density Fˆ on the one hand and ˜ and the mass density the deformation gradient F, the constrained deformation gradient F, ρ on the other hand. The factor of isotropic dilation in the current configuration is denoted by λ. For dimensional reasons, a constant ϕ with dimension (length)−3/2 , which relates to the square root of a unit volume in the reference state, must be introduced into the relation ˆ Since ϕ is without any consequence for the dynamics, it is set to unity in between F and F. the following. The symbol ρ is a constant with appropriate dimensions so that ρ represents a mass density. Further details are given in the text. Variable

Scaling

Relation to Fˆ

Fˆ

λ−2

–

F

λ

F˜

1

ρ

λ−3

ˆ det Fˆ ϕ F/ ˆ 3 det Fˆ F/ ρ∗ det Fˆ

Evolution Equation ∂ ˆ ∂t F = −v · ∂ ∂t F = −v · ∂ ˜ ∂t F = −v · ∂ ∂ ∂t ρ = − ∂r

∂ ˆ ˆ ∂r F + [κ − (trκ)1] · F ∂ F+κ·F ∂r ∂ ˜ 1 ˜ ∂r F + κ − 3 (trκ)1 · F

· (ρv)

ˆ ˆ

above, where also L(u,u) has been calculated (see (5.4b)). Second, L(F,F) = 0 since the microscopic expression (5.10b) does not depend on the particle momenta, and ˆ ˆ one can also show that L(e,F) = 0 and L(F,e) = 0. For the determination of the ele(u,e) , one could depart from (5.3), which would lead to a result analogous to ment L the above hydrodynamic case with a microscopic expression for the stress tensor σ. However, in order to obtain an expression for the stress tensor directly in terms of the independent coarse-grained variables x, we alternatively choose to exploit the degeneracy condition (2.3d) to determine L(u,e) , which in turn leads to L(e,u) due to the antisymmetry condition (2.3b). In summary, one then recovers after some calculations the Poisson operator (3.32) after replacing L(uα ,Fγ ) (r, r ) and ˆ ˆ L(Fαβ ,uγ ) (r, r ) by the expressions for L(uα ,Fγ ) (r, r ) and L(Fαβ ,uγ ) (r, r ), respectively, as defined in (5.12). The stress tensor expression is identical to (3.33). Therefore, the reversible contributions to the evolution equations of x as obtained from the coarse graining procedure agree with the corresponding terms in (3.34), except for the necessary replacement of (3.34c) by (5.13) due to consideration of the deformation gradient density. So, from the perspective of the coarse graining procedure, it is suggestive to use the set of variables ˆ x = (u, e, F),

(5.14)

rather than (3.29) employed previously in Section 3.4. We conclude the discussion of the Poisson operator with a comment on the Jacobi identity. Since the Jacobi identity is invariant with respect to a transformation of variables from (u, e, F) to ˆ and since the identity has been proven for (3.32), it must also be satisfied (u, e, F) for the expression derived in this section.


297

5.2.4. Friction Matrix – Irreversible Dynamics The Green–Kubo type relation (4.11) demonstrates the intimate relation between dissipative processes on long time scales, described by the plastic velocity gradient tensor κp,c above, and fluctuations on short time scales. All the variables in the set (5.14) show irreversible behavior, for example, viscous stresses, heat flux, and plastic deformation. Therefore, in view of (4.11), all the variables in (5.14) fluctuate on short time scales. Since the microscopic dynamics conserves both the total momentum and the total energy, we make the same ansatz for the fluctuations ˙ fu (z; r) and ˙ fe (z; r) as in (5.6b) and (5.6c), respectively. As a consequence, one can show that the total energy is unaffected by the fluctuations, δE ˙ fx (z; r)d 3 r = 0, · (5.15) δx(r) if the condition ∂ρ(r) ˙ f (z; r) = 0 ˆ ∂Fˆ μν (r) Fμν

(5.16)

(using Einstein’s summation convention) is fulfilled. This last condition is satisfied for the treatment presented below, where we consider only isochoric irreversible deformations, that is, the viscoplastic deformation leaves the mass density unchanged. As we have seen in Section 5.1, the self-correlations of the fluctuating stress tensor σ f will give rise to a viscous stress in the coarse-grained momentum balance, while the fluctuating heat flux jq,f leads to Fick’s law of heat conduction. To simplify the further procedure, we assume that the fluctuations ˙ fu (z; r), ˙ fe (z; r), and ˙ f (z; r) are all uncorrelated from each other, and conse Fˆ quently there will also be no cross-effects. Since the main objective of this study is to derive detailed expressions for the plastic velocity gradient tensor, we will focus ˙ f (z; r), that in turn amount to on fluctuations in the elastic deformation gradient, Fˆ dissipative effects on the macroscopic scale described by the lower right element of ˆˆ M, MFF , according to (4.11). To that end, we implicitly interpret the microscopic definition (5.10b) as representing only the elastic part of the deformation. However, that requires subtle changes in the interpretation of the quantities involved in (5.10b), which will be addressed at the end of the Section 6. The friction matrix element associated with the relaxation of the elastic deformation gradient density can be conveniently written in the form (4.11b) with Fˆ (z; r) having even parity under time reversal. To simplify the notation, we define the increment of the microscopic deformation gradient density over a time interval of duration τ as ˆ

WF ≡ τ fˆ (z) = fˆ (z(τ)) − fˆ (z(0)), F

F

F

(5.17)

298


where τ is the characteristic time scale separating the fast from the slow processes. ˙ f (z(t); r) has the characteristics of white noise, the quantity We mention that if ˆ F

ˆ

WF is a Wiener process (Gardiner, 1985; Öttinger, 1996). Volume Conservation upon Plastic Deformation The volume conservation of the fluctuations can be made explicit by using the projection operator (3.37). Particularly, since the mass density ρ depends on Fˆ only through the determinant (see Table 5.1) and by virtue of the identity (3.38), one can show that ∂ρ Fˆ Pαβγ Wγ = 0, ∂Fˆ αβ

(5.18)

that is, the mass density is not affected by the fluctuations, and (5.16) is satisfied. Fˆ rather than W Fˆ Inserting the manifestly volume-conserving fluctuations Pαβγ Wγ αβ into the friction matrix (4.11b), one obtains ˆ

ˆ

M Fαβ Fγ (r, r ) =

1 Fˆ Fˆ (r)Wκλ (r ) Pγκλ (r ). Pαβμν (r) Wμν x 2kB τ ˆ

(5.19)

ˆ

In this form, the element M Fαβ Fγ describing the viscoplastic relaxation of the deformation gradient density satisfies all the GENERIC properties (2.3e–2.3g). In other words, all what follows is, therefore, automatically in full agreement with the framework of nonequilibrium thermodynamics. In the remainder of the manuscript, we assume for clarity that no correlation ˆ exists between the noise WF at different positions. Therefore, one may write Fˆ Fˆ ˆ (r) Wκλ (r ) = (det F(r)) μνκλ (r) δ(r − r ), (5.20) Wμν x

with a fourth-rank tensor. However, nonlocal correlations can be incorporated readily by only slight modifications of the treatment we present below, if ˆ which is constant upon plastic deformation, so desired. The prefactor (det F), has been introduced for later convenience, particularly for (5.21b) and all related further developments. With the form (5.19) of the friction matrix, the irreversible contribution to the macroscopic evolution equation for the elastic deformation gradient density can ˆ ˆ be computed readily using the last term of (2.3a). Multiplication of MF F (r, r ) ˆ F)(r ˆ with (∂s(e, F)/∂ ) and summation over discrete and continuous indices (i.e., integration over r ) lead to ∂ det Fˆ dev ˆ −1 Fˆ αβ = − Pαβμν μνκλ (σκρ Fλρ ), ∂t 2k Tτ B irr

(5.21a)


299

where we have used the expression (3.45) for the elastic part of the Cauchy stress ˆ tensor, and σ dev denotesits deviatoric part. Since (∂ det F/∂t)| irr = 0 and by virtue e ˆ det Fˆ (see Table 5.1), the above equation can be rewritten of the relation F = F/ in the form ∂ e 1 dev e,−1 Fλρ ). (5.21b) Fαβ = − Pαβμν μνκλ (σκρ ∂t 2k Tτ B irr Since this form is more convenient for comparison with expressions in literature, we shall proceed with (5.21b) in the following. At this point, we are in the position to compare the current findings to the results presented in the single-level formulation in Section 3.4. A comparison of the friction matrices (3.40) and (5.19, 5.20) leads to the identification ¯ =

1 , 2kB τ

(5.22)

which also emerges in the irreversible contributions to the evolution equations of Fe , (3.42) and (5.21b). Therefore, what was previously set as a phenomenological ¯ is now supplemented with microscopic detail by way of the fourth-rank tensor fluctuations (5.20). Proper Representation of Fluctuations In order to learn about the structure of the tensor in (5.20, 5.21), we now address the form of the fluctuations in the e ˆ deformation gradient density WF , which is related to the fluctuations WF in the deformation gradient according to ˆ

WF e = WF , det Fˆ

(5.23) e

the latter of which we examine in more detail. Our interest in WF rather than ˆ WF in this section is aimed at avoiding the spurious additional density effect in Fˆ discussed earlier (see Sections 5.2.1 and 5.2.3). Furthermore, it is in agreement with (5.21b), that is, to simplify comparison with literature results. However, the Fe and Fˆ representations can be used interchangeably with only slight modifications of the subsequent analysis since volume conservation upon plastic deformation implies that both pictures are related by a constant prefactor. Since the elastic deformation gradient is a mapping from the reference state e onto the current state, this also holds true for the fluctuations WF . In order to proceed, we introduce appropriate coordinate systems in both spaces. Physically, symmetry axes in anisotropic materials offer a natural definition of a coordinate system. In the reference state, we introduce the triad of linearly independent vectors

300


dir (i = 1, 2, 3). Note that we do not require that either those vectors have unit length or they are orthogonal to each other. Furthermore, it is convenient to introduce the triad of dual vectors dˆ ir (i = 1, 2, 3) with the conditions dˆ ir · djr = δij , with δij the Kronecker delta. For the triad of base vectors in the current state we choose dic = Fe · dir (i = 1, 2, 3), that is, the vectors dir transported from the reference to the current state. Corresponding to the procedure in the reference state, also in the current state dual vectors can be defined dˆ ic (i = 1, 2, 3) based on the conditions dˆ ic · djc = δij . It can be shown with the aid of dic = Fe · dir (i = 1, 2, 3) that the dual vectors in the reference and in the current state, are related by dˆ c = dˆ r · Fe,−1 i

i

(i = 1, 2, 3). In summary, we have the following relations between the vectors, the dual vectors, and the elastic deformation gradient, dic = Fe · dir ,

(i = 1, 2, 3),

(5.24a)

dˆ ic = dˆ ir · Fe,−1 ,

(i = 1, 2, 3),

(5.24b)

where all quantities are slow (i.e., not fluctuating) by definition since Fe is slow. We note that with the aid of the above definitions, the identity Fe =

3

dic dˆ ir

(5.24c)

i=1

can be derived readily. Previous authors have proposed similar sets of base vectors (and dual vectors) in the description of elasto-viscoplasticity of anisotropic materials. Naghdi and Srinivasa (1993) introduced “lattice directors” to describe structured continua, their definition being focused on volume averaging of lattice vectors rather than on time averaging as above. Rubin (1994, 1996) used a triad of vectors to describe the relative orientation of a crystal during plastic deformation. Also Besseling introduced a triad of vectors to define the so-called natural reference state, which was used conceptually to model elasto-viscoplasticity (Besseling and Van der Giessen, 1994, page 244). A detailed comparison of the use of these different base vectors to describe viscoplastic deformation can be found in Rubin (1994, 1996). e Since the fluctuation of the elastic deformation gradient, WF , is a mapping between the reference and the current state, it is the natural choice to expand it in terms of dual vectors in the reference state and vectors in the current state, although other choices are possible in principle. The fluctuations on the elastic deformation gradient can, therefore, be written in the form e

WF =

ij

wij dic dˆ jr ,

(5.25)


301

where on the right-hand side only the expansion coefficients wij represent noise, with wij x = 0 for all (i, j). The form of the representation (5.25) is most important for the further discussions. In particular, the fact that the vectors dic and dˆ jr are not fluctuating and transform according to (5.24) will have important ramifications. We point out, however, that (5.25) is merely a convenient representation of the fluctuations and is not deeply rooted in the definition (5.10b). We will touch upon this point again in the final Section 6. In the absence of spatial correlations of the noise, we write wij (r)wkl (r ) x = 2kB T τ cijkl (r) δ(r − r ) , (5.26) with prefactors introduced for later convenience. Physically, kB indicates that fluctuations are of statistical nature, while T highlights the thermal aspect, with fluctuations vanishing at 0 K. With this, the tensor introduced in (5.20) with (5.23) takes the form = 2kB T τ cijkl dic dˆ jr dkc dˆ lr , (5.27) ijkl

all quantities being evaluated at r. At this point, it should be noted that GENERIC only requires the “kinetic prefactors” cijkl to be symmetric and positive semidefinite (which is manifested in (5.26)), still leaving plenty of room for a complicated dependence on x. In particular, to mimic the presence of a yield stress, the prefactors cijkl are to be selected as highly nonlinear functions of the elastic stress tensor, in accord with our earlier comments after (3.43) in relation to macroscopic modeling. With (5.27), one obtains for the plastic deformation rate of Fe according to (5.21b), ⎡ ⎤ ∂ e = −P : ⎣ cijkl dkc · σ dev · Fe,T,−1 · dˆ lr dic dˆ jr ⎦ , (5.28) F ∂t irr

ijkl

where the double contraction is understood as Pαβμν [. . .]μν (note the order of indices). We note at this point that the Green–Kubo type relation (4.11) has been employed here for highlighting the effect of anisotropy on viscoplastic deformation. However, we do not evaluate the correlation functions cijkl in microscopic terms. Alternative Interpretations of Fluctuations In the above treatment, we have emphasized the fact that, on this level of description, the mapping itself fluctuates. However, it will be convenient to express these fluctuations exclusively with respect to either the reference or the current state, as will be demonstrated below. This will be useful in the applications (Sections 5.2.5–5.2.7) since specific constitutive relations are discussed and compared to known results more conveniently

302


in these forms rather than (5.28). Nevertheless, it is important to realize that both these representations are formally equivalent, as on this level of description, using Fˆ or Fe as a state variable, the fluctuations and dissipative dynamics occur on the mapping itself. e If one uses (5.24a) to rewrite the fluctuations (5.25), one obtains WF = Fe · r r r r r W with W = ij wij di dˆ j . The quantity W is expressed exclusively in terms of vectors and dual vectors in the reference state. Therefore, Wr describes the fluctuations of the deformation gradient solely with respect to the reference state. Introduction of the splitting (5.24a) in the evolution equation (5.28) then leads to a description of the dissipative processes solely with respect to the reference state as ∂ e 1 p,r p,r e F tr κ˘ 1 ≡ −Fe · κp,r , = −F · κ˘ − (5.29a) ∂t irr 3 with the unconstrained plastic velocity gradient tensor in the reference state, κ˘ p,r , given by κ˘ p,r = cijkl dkr · dev · dˆ lr dir dˆ jr , (5.29b) ijkl

dev = Fe,T · σ dev · Fe,T,−1 .

(5.29c)

Here, dev is the driving force in the reference state for plastic deformation with property trdev = 0. Within a prefactor proportional to the mass density ρ, this expression for the driving force in the reference state is identical to what is used by Besseling and Van der Giessen (1994, page 258), who derive it based on the energy dissipation rate as the flux conjugate to the plastic velocity gradient tensor in the reference state. In contrast to interpreting fluctuations and dissipative processes of the deformation gradient Fe in the reference state, Eq. (5.24b) can be used to obtain a e description of WF with respect to the current state. In this case, one obtains along e similar lines as above WF = Wc · Fe , with Wc = ij wij dic dˆ jc being the fluctuations described in current space. With (5.24b), the evolution equation (5.28) then assumes the form ∂ e 1 p,c p,c F tr κ˘ 1 · Fe ≡ −κp,c · Fe , = − κ˘ − (5.30a) ∂t irr 3 with the unconstrained plastic velocity gradient tensor in the current state, κ˘ p,c , given by κ˘ p,c = cijkl dkc · σ dev · dˆ lc dic dˆ jc . (5.30b) ijkl


303

Note that the driving force in the current state for plastic deformation is given by the deviatoric Cauchy stress tensor σ dev , in contrast to dev , which is relevant if the perspective of the reference state is adopted. The plastic velocity gradient tensor κ˘ p,c can, in principle, be written as a superposition of dyadic products dˆ ic dˆ jc , as done by Rubin (1994, 1996). However, the representation (5.30b) based on the dyadic products dic dˆ jc was preferred by us, as it is intimately related to the parameterization (5.25) of the fluctuations on the elastic deformation gradient. In summary, the effect of rate-dependent plastic deformation can be expressed in either of the two equivalent forms (5.29) and (5.30), with κp,r and κp,c , the plastic velocity gradient tensor in the reference and current state, respectively. In particular applications, the main points concern a suitable choice of the anisotropy vectors, and the calculation of the correlations cijkl defined through (5.25) and (5.26). The expression for the deviatoric part of the stress tensor, σ dev , derives purely from the static properties of the material in terms of the generating functionals, (3.45), and will not be discussed in detail in the examples below. 5.2.5. Application 1: Crystal Plasticity and Slip Systems Plastic deformation in crystals occurs primarily by sliding along specific shear planes. If the normal to the sliding surface is denoted by mc and the sliding direction by sc in the current state, then (sc , mc ) is called a slip system. With the identifications mc = dˆ 2c , and sc = d1c and by virtue of sc · mc = 0, slip systems are a special case of our general treatment given above in Section 5.2.4 for which e the fluctuations WF consist only of a single term on the right-hand side of (5.25), and the fourth-rank tensor c has only one nonzero element, c. The plastic velocity gradient tensor in the current state (5.30b) then assumes the form κ˘ p,c = c (sc · σ dev · mc ) sc mc ,

(5.31a)

in full agreement with Asaro (1983) and Peirce et al. (1983), who selected the prefactor c to be a highly nonlinear function of σ dev to mimic the presence of a yield stress. In (5.31a), the term in parentheses is called the resolved shear stress τ c = sc · σ dev · mc in the current state. Note that the resolved shear stress is invariant with respect to choosing either the full stress tensor σ or the deviatoric part σ dev in its definition. Usually, several slip systems are active in crystalline materials. If the fluctuations for each slip system are independent of each other, the above result can be generalized to κ˘ p,c = c(α) (sαc · σ dev · mαc ) sαc mαc , (5.31b) α

304


with ταc = sαc · σ dev · mαc the resolved shear stress on slip system α. A similar expression holds for the plastic rate in the reference state according to (5.29b) by way of the transformation rules (5.24). 5.2.6. Application 2: Transversely Isotropic System Here, we discuss systems for which the fluctuations in the elastic deformation gradient are transversely isotropic. Transversly isotropic materials possess rotational symmetry around a specific axis, for example, uniaxially stretched polymers. For this example, we assume that cross-correlations between fluctuations wij in (5.25) are absent so that the correlations cijkl ∝ δik δjl . Therefore, the quadruple sums in (5.28, 5.29b, 5.30b) become double sums, with cijkl replaced by c˜ ij . We begin with studying a material that is transversely isotropic in the reference state, that is, prior to deformation. To that end, we use an orthonormal triad of vectors with nir ≡ dir = dˆ ir and nir · njr = δij . The vector n3r points along the symmetry axis. Transverse isotropy imposes certain conditions on the correlations c˜ ij . Due to the rotational invariance around n3r in the plane spanned by the vectors (n1r , n2r ), we conclude that c˜ 11 = c˜ 22 = c˜ 12 = c˜ 21 ,

(5.32a)

c˜ 13 = c˜ 23 ,

(5.32b)

c˜ 31 = c˜ 32 .

(5.32c)

With this, the plastic velocity gradient tensor (5.29b) can be written in the form κ˘ p,r = c˜ 11 dev + (˜c11 + c˜ 33 − c˜ 13 − c˜ 31 )Nr · dev · Nr c˜ 31 + c˜ 13 + − c˜ 11 Nr · dev + dev · Nr 2 c˜ 31 − c˜ 13 r + N · dev − dev · Nr , 2

(5.33)

with the projector on the symmetry axis given by Nr ≡ n3r n3r . Acommon procedure for expressing the tensorial structure of the plastic velocity gradient tensor in the reference and current state consists in using the representation theorem of isotropic tensor functions (Wang, 1970, 1971; Spencer, 1971; Loret, 1983; Dafalias, 1985a; Dafalias, 1985b; Van der Giessen, 1991). One starts with selecting the fundamental tensors to which the representation theorem shall be applied. To model κ˘ p,r for transversely anisotropic materials, a logical choice of variables would be Nr and the driving force for plastic deformation dev (see (5.29b), (5.29c) and Besseling and Van der Giessen (1994), page 258). It should be noted that dev itself is generally nonsymmetric but can be expressed as the


305

product of two symmetric tensors: dev = (ρ/ρ0 )Ce · with Ce = Fe,T · Fe and the second Piola–Kirchhoff stress tensor, . Unfortunately, using the representation theorem on the triplet of symmetric tensors , Nr and Ce to express κ˘ p,r would lead to an abundant number of coefficients. Therefore, it is normally assumed that κ˘ p,r only depends on Nr and even though itself is not dual to κ˘ p,r . Application of the representation theorem to the doublet Nr and and collecting the linear terms in then lead to κ˘ p,r = α1 + α2 Nr · · Nr + α3 Nr · + · Nr + α4 Nr · − · Nr . (5.34) Here, the term Nr · · Nr follows from the representation theorem but is usually omitted. The advantage of using the microscopically motivated expression (5.33) for κ˘ p,r is now evident. Without assumptions, it expresses κ˘ p,r as a function of Nr and the more appealing dev , using the same number of coefficients as in (5.34). In addition, it provides a microscopic interpretation of these coefficients. For the case of fully isotropic fluctuations, c˜ ij = c˜ (∀ i, j), the plastic velocity gradient tensor (5.33) reduces to κ˘ p,r = c˜ dev . With the aid of the formal equivalence Fe · κp,r = κp,c · Fe , one obtains the plastic velocity gradient tensor in the current state as κ˘ p,c = c˜ Be · σ dev · Be,−1 with the elastic left Cauchy–Green strain tensor Be = Fe · Fe,T . In summary, for isotropic fluctuations, κ˘ p,r = c˜ dev , κ˘

p,c

= c˜ Be · σ dev · Be,−1 .

(5.35a) (5.35b)

It is essential to note that if and only if the thermodynamic potential (3.30) describes an isotropic material, one has Be · σ dev = σ dev · Be , and therefore κ˘ p,c = c˜ σ dev ,

(5.35c)

which has been used abundantly to describe elasto-viscoplastic deformation (Rice, 1971; Tervoort et al., 1998; Govaert et al., 2000). Conclusively, expression (5.35c) is the result of isotropy in both the (static) thermodynamic properties and the (dynamic) microscopic fluctuations. While isotropy holds simultaneously in the reference, (5.35a), and in the current state, (5.35c), this is not true for transverse isotropy. Consider the above example with symmetry axis n3r . The state that is transversely isotropic in the reference state looses transverse isotropy when deformed, for example, according to the deformation Fe = 1 + γn1r n3r with shear strain γ. Since transverse isotropy in the current state is of transient nature only, we do not discuss it in detail here. We mention though that it can, and indeed has been, be modeled on purely macroscopic grounds (Hütter and Tervoort, 2008b; Van der Giessen, 1991).

306


The concept of plastic spin has been a subject of debate for more than two decades. In most of the cases, it is defined as the antisymmetric part of the plastic velocity gradient tensor in the reference state, κ˘ p,r (Loret, 1983; Dafalias, 1985a,b, 1998), but also the current state formulation with κ˘ p,c being used for its definition (Van der Giessen, 1991). This debate is closely linked to the goal of formulating constitutive relations for the symmetric and the antisymmetric parts of the plastic velocity gradient tensor, often with the aid of the representation theorem for isotropic tensor functions. Such procedures differ from our treatment in three major aspects. First, we have pointed out that on this level of description, the fluctuations, and hence the dissipative effects, occur on the mapping Fe itself, rather than in either reference or current space. Expressing the irreversible (i.e., plastic) effects in the dynamics of Fe in terms of plastic velocity gradient tensor κ˘ p,r or κ˘ p,c simply leads to two manifestations of the same physics. As pointed out earlier, the plastic velocity gradient tensors are introduced here only for convenience, but not out of necessity. The second difference is interrelated with the first one. For example, requiring the symmetry of κ˘ p,r does not automatically translate into the symmetry of κ˘ p,c = Fe · κ˘ p,r · Fe,−1 . Hence, the plastic spin discussion depends strongly on the choice of the space (reference vs. current). Such a conflict is absent in our treatment. The third difference concerns the degree of determination in the constitutive modeling. In our approach, constitutive modeling is restricted to the coefficients c˜ ij , or cijkl more generally. In contrast, when using the representation theorem, a certain arbitrariness in the proper choice of the fundamental symmetric tensors is inherent to the procedure. For completeness, we point out that in (5.33), all terms lead to antisymmetric contributions since, in general, dev = dev,T , irrespective of the kinetic coefficients c˜ ij . In other words, antisymmetric terms in the plastic velocity gradient tensor arise simultaneously with the symmetric ones for materials with anisotropic thermodynamic properties. Only for a material with isotropic thermodynamic properties, one has dev = dev,T , in which case, only the last term in (5.33) is antisymmetric, which does not contribute if c˜ 31 = c˜ 13 , that is, if the shear fluctuations are isotropic as well. Finally, it should be mentioned that the coefficients c˜ ij in (5.33) will, in general, depend on the state of deformation through Fe . It is reasonable to assume that the most important effect of the state of deformation enters through the stress tensor and its projections parallel and transverse to the symmetry axis. Accordingly, the ¯k coefficients c˜ ij may be represented in the form c˜ ij (I1 , I2 , I3 ), where Ik = tr is the k-th invariant of the dimensionless tensor ¯ = 1 adev + bNr · dev + cdev · Nr + dNr · dev · Nr , σ0

(5.36)


307

with characteristic stress σ0 and dimensionless coefficients (a, b, c, d). We point out that if c˜ ij is a strong function of Ik , the stress level at which the viscoplastic flow becomes significant can be identified with the yield surface used in rateindependent plasticity theories. Particularly, for c˜ ij (I2 ), the pseudoyield surface in the viscoplastic description is given for I2 of order unity. This latter condition is identical to the famous yield criterion of Hill (1948) for transversely isotropic solids in the case of small deformations, where dev is symmetric. 5.2.7. Application 3: Relation to Microscopic Computer Simulations of Plastic Deformation Establishing a relation between plastic deformation on the macroscopic scale and the microscopic fluctuations, as done here, is interesting from the perspective of atomistic computer simulations (see Abraham, 1997a; Abraham et al., 1997b; Bulatov et al., 1995; Bulatov et al., 1998, and Li et al. (2002) and references 7– 10 therein). One can envision to observe microscopic fluctuations, determine the correlations between them, and then calculate the macroscopic plastic deformation process by way of (5.28, 5.29b, 5.30b). We briefly touch on the main steps in that procedure. Microscopic simulations allow one to follow trajectories of atoms or united atoms. As the evolution of the system is solved numerically, it is convenient in regard to simulations to adopt the view that the reference state remains constant, while the fluctuations in the deformation gradient occur as a result of the dynamics in the current state. For example, in crystals, the current positions of the atoms snap back and forth due to the irregular hopping mechanisms associated with the motion of the dislocations through the lattice (Orowan, 1934; Von Polanyi, 1934; Taylor, 1934; Nabarro, 1967; Hirth and Lothe, 1982). In this sense, the anisotropy vectors djr must be considered as the anisotropy vectors in some initial (possibly stress free) state of the simulation. Starting from that initial configuration, the system evolves dynamically under the action of an applied stress, while the atoms fluctuate thermally and due to the irregular motion of dislocations. The fluctuations are then to be extracted from the simulation in a macroscopically stationary state, that is, when the macroscopic variables x do not change. In order to determine the fluctuations wij in (5.25), it is useful to first make the volume conservation manifest. We apply the projection P to (5.25) and subsequently multiply that expression with dˆ ic and djr from the left and right, respectively, to arrive at 1 e c F r wkk δij . (5.37) dˆ i · P : W · dj = wij − 3 k

The term in the parentheses on the left-hand side represents the fluctuating contribution to the evolution of djr as deformed out of the reference state. This vector is

308


multiplied with the slowly evolving dual vector dˆ ic , which can be constructed once the averages dic are determined from the simulation run. Therefore, the expression (5.37) allows one, in principle, to extract information about the fluctuations wij 1 from the simulations. The term − 3 k wkk δij on the left side originates from the action of the projection P, and so the trace of the matrix of coefficients wij cannot be measured. However, this is without significant consequences as it can be shown that the friction matrix (5.19) is unaffected by a shift in the trace of the matrix wij . We point out that, in effect, the trace of the left-hand side in (5.37) can be used as a criterion to check if the plastic deformation is incompressible since 3

e dˆ ic · P : WF · dir = 0

(5.38)

i=1

should hold. Once sufficient information about the matrix of coefficients wij is collected from the simulations, the determination of their correlations, cijkl defined in (5.26), can be addressed. However, we must emphasize that some difficulties with the application of (5.37) in computer simulations exist in relation to the identification of a “reference state,” as elaborated on at the end of the Section 6.

6. Discussion The main goal of this contribution was to regard the evolution equations of macroscopic elasto-viscoplasticity as being coarse grained from the microscopic dynamics of the constituent particles. Specifically, our interest was to provide a microscopic interpretation of the plastic velocity gradient tensor in macroscopic dynamic models of anisotropic elasto-viscoplasticity. This goal was achieved by using the general equation for the nonequilibrium reversible-irreversible coupling (GENERIC) and by applying its method for connecting different levels of description (Öttinger, 2005). The emergence of irreversible effects upon coarse graining is particularly interesting in this respect. In general, the time correlations between microscopic fluctuations give rise to irreversible processes on the macroscopic scale (de Groot and Mazur, 1962; Kubo et al., 1991; Evans and Morriss, 1990; Öttinger, 2005), as demonstrated, for example, in the well-known Green–Kubo relation for the shear viscosity in Newtonian fluids. Temporal coarse graining is hence a powerful tool to get a closer and more detailed look at dissipative effects. It is tempting to apply such techniques not only to fluid mechanics but also to the field of solid mechanics. The coarse graining of Hamiltonian point mechanics towards a field theory of nonisothermal compressible hydrodynamics illustrated the main steps of the


309

procedure in Section 5.1. While the corresponding Poisson operator of hydrodynamics could be derived in a straightforward manner based on the microscopic dynamics, the form of the friction matrix was deduced using Onsager’s regression hypothesis. In particular, it has proven useful to incorporate some aspects about the structure of the fluctuations, to arrive at, for example, an interpretation of the viscosity in terms of stress–stress correlations. As the main theme of this contribution, we have examined the coarse graining from Hamiltonian point mechanics towards a field theory of elasto-viscoplasticity in Section 5.2. Also in this case, there was a marked difference between the calculation of the reversible and the irreversible contributions to the evolution equations. Based on the microscopic definition of the so-called deformation gradient density (5.10), the Poisson operator could be derived by straightforward calculations. However, without going into microscopic details, it was sufficient to assume a particular representation of the fluctuations of the elastic deformation gradient (see (5.19) and (5.25)) to account for the influence of material anisotropy on the structure of the plastic velocity gradient tensor. So, similar to the treatment of hydrodynamics, at no point in time, we have explicitly calculated the fluctuations, but we only profited from particular structural aspects in the form of the fluctuations. Our results about the plastic velocity gradient tensor crucially depend on the notion that the elastic part of the deformation gradient, Fe , is a suitable dynamic variable for the description of anisotropic elasto-viscoplasticity. Most notably, Fe and, in particular, the fluctuations on it, which enter into the generalized fluctuation–dissipation theorem, are mappings between the reference and the current states. With that in mind, the representation (5.25) of the fluctuations is most meaningful and has many important ramifications. Although on this level of description the dissipative effects occur on the mapping itself between the two spaces, we have shown that the plastic effects can be expressed in terms of a plastic velocity gradient tensor in either the reference or current space, simplifying the comparison with existing constitutive relations. The main achievement of our treatment is that it structures the modeling of viscoplastic effects for anisotropic materials. Motivated by the Green–Kubo type relation (4.11), we have studied the effect of anisotropy on the viscoplastic deformation. Although we have not performed the calculation of the correlation functions cijkl in microscopic terms, many useful conclusions have emerged. First, the thermodynamic driving force for plastic deformation is identified. In general terms, it is given by σ dev · Fe,T,−1 = Fe,T,−1 · dev in (5.21b, 5.28), while it takes the form dev or σ dev when interpreted in the reference or current space, respece tively. Second, by way of the ansatz (5.25) for the fluctuations WF , the kinetic contributions are expressed in the form (5.27). The anisotropy axes inherent to the material are accounted for by the triads of vectors dir in the reference state and all the corresponding vectors and dual vectors in the reference and current space

310


(see Section 5.2.4). The particular representation (5.25) of the fluctuations in terms of the directions of anisotropy allows one to interpret the fluctuating coefficients wij physically. In particular, they are related to the averages and fluctuations of the anisotropy directions. We envision that, after some further conceptual clarifications (see further below), the coefficients wij can be obtained from microscopic computer simulations, as we have alluded to in Section 5.2.7. In other words, we hope that our treatment will aid a targeted analysis of microscopic simulations. Namely, the fluctuations wij given by (5.37) and the correlations between them must be studied in order to most efficiently access the macroscopic effects of plastic deformation. Two illustrative examples have been considered in Sections 5.2.5 and 5.2.6, namely crystalline systems with slip planes and transversely isotropic materials. Both these examples are naturally expressed as special cases of our general treatment by imposing specific, physically motivated, conditions on the fluctuations wij . In contrast, current procedures are rather different for these two cases and less intuitive in the case of transversely isotropic materials. In both examples, the coefficients c(α) and c˜ ij are undetermined within our framework, specifically as far as the dependence on the state of deformation is concerned. These coefficients can be obtained from experiments under standard conditions. Appropriate expressions for them have been proposed for crystalline systems (Hutchinson, 1976; Asaro, 1983; Peirce et al., 1983; Pan and Rice, 1983) and for example, polycarbonate in the solid state (Tervoort et al., 1996, 1998; Tervoort and Govaert, 2000), where stressactivated hopping comes into play, as described by the Eyring viscosity (Krausz and Eyring, 1975). As an attractive alternative to experiments, such relations may in the future be verified against simulations, where the fluctuations wij and the correlations cijkl can be determined. As a next step, it could then be envisaged to supplement or even replace Fe with more detailed variables to resolve some of the physics behind plastic deformation that is now hidden in the coefficients cijkl . As the example discussed in Section 5.2 was concerned with coarse graining from the microscopic level L0 to the macroscopic level L2 , reformulating the physics behind plastic deformation in more explicit and intuitive terms is equivalent to introducing an intermediate level L1 into the description (see Fig. 4.1 and Table 4.1). This intermediate level L1 serves as an additional “sieve” for distilling out the essentials when coarse graining from L0 to L2 . For example, in crystalline materials, that could be achieved in terms of a reduced description for the dynamics of dislocations (Groma, 1997; Groma and Balogh, 1999; Groma et al., 2003; El-Azab, 2000; Arsenlis et al., 2004). Similar strategies of introducing structural variables on intermediate levels have been and are currently being followed successfully in modeling the rheology of polymer solutions and melts (Bird et al., 1987; Larson, 1988).


311

The concept of plastic spin has been briefly touched upon in Section 5.2.6 for the example of transversely isotropic systems. We have shown that in our treatment, antisymmetric terms in the plastic velocity gradient tensor arise simultaneously with the symmetric ones for materials with anisotropic thermodynamic properties. Therefore, the plastic spin, which is often introduced to compose constitutive relations for the plastic velocity gradient tensor, arises naturally in our treatment and does not require any special considerations. Finally, we discuss the determination of fluctuations in the elastic deformation gradient in practical applications. As pointed out, (5.25) is merely a convenient representation of the fluctuations that lacks a direct relation to the microscopic definition of the deformation gradient density (5.10b). However, if one intends to use (5.10b) in relation to viscoplastic deformation and interpret it in terms of the elastic part of the deformation gradient density, it must be noted that the use of vectors in what was loosely called the initial configuration or reference configuration (RC) in (5.10b) becomes complicated. To illustrate the problem, we consider a single crystal with layers moving past each other under plastic deformation. Two particles, which are close to each other at the beginning of the simulation and placed in different layers, will be increasingly separated even under steady plastic deformation although the elastic deformation gradient is constant. Therefore, to identify the elastic deformation gradient properly, (at least) two alternatives exist. Either one keeps the initial configuration fixed. This requires, though, a subtle relabeling of particles during the dynamics in the current state in such a way that the particles relax to their positions in the RC upon the cessation of the applied stress. Or, as a second alternative, one does not relabel the positions of the evolving particles, but in turn one continuously redefines the RC as to represent the “next closest reference state” with respect to which the elastic deformation is measured. At present, it is unclear to us how such a scheme could be implemented in practice. For these reasons, the expressions presented in Section 5.2.7 are not ready to be used in numerical applications but rather should be understood as an indication of conceptual difficulties that should be addressed in the future. Nevertheless, fortunately, the form (5.10b) of the deformation gradient density can be used for motivating further the ansatz (5.25) for the fluctuations. Particularly, in the case of single-crystal plasticity, dislocations move in specific slip planes and directions which in turn leads to particle jumps along these directions and hence also fluctuations in the deformation gradient along these directions, in support of the expressions (5.31). It is noted that all the difficult issues with using the microscopic definition (5.10b) in plastic deformation have one common cause, namely the fact that the instantaneous deformation gradient density involves not only the current positions of the particles but also their positions in an RC that is difficult to specify unambiguously. It seems to us that a microscopic definition of a measure

312


of deformation in elasticity cannot depend only on the current configuration. This is in line with other efforts in literature that use either explicitly (Falk and Langer, 1998; Goldhirsch and Goldenberg, 2002) or implicitly (Buehler et al., 2004; Zimmerman, 1999) the notion of an RC. However, apart from being highly unusual, the use of the RC brings about the issues discussed above. Despite all the conclusions that could be drawn already now, we feel that specification of the reference state remains a critical issue in coarse graining from a microscopic to a macroscopic description of the plastic deformation in solid materials. Acknowledgments We are grateful to Hans Christian Öttinger for a critical reading of the manuscript and for stimulating discussions. MH acknowledges useful discussions with Patrick Ilg concerning Section 5.1. Appendix A

Calculations Related to Hydrodynamics (Section 3.3)

In this Appendix, the application of the Poisson operator (3.17) and the friction matrix (3.20) to the functional derivatives (3.16) is calculated for some exemplary cases. To that end, the following auxiliary identities are useful, ∂δ ∂ f(r) g(r )d 3 r = f(r) g(r), (A.1) ∂r ∂r ∂δ ∂ (A.2) f(r ) g(r )d 3 r = (f(r)g(r)), ∂r ∂r ∂δ ∂δ = − , (A.3) ∂r ∂r with δ = δ(r − r ) being the Dirac delta function, and f and g two arbitrary functions. The u-component of the degeneracy condition (2.3d) can then be written in the form δS ∂ ∂s ∂ ∂s ∂ p Lu,k (r, r ) d 3 r = −ρ −e − ∂r ∂ρ δxk (r ) ∂r ∂e ∂r T k ∂s ∂s p ∂ s−ρ −e − = 0 , (A.4) = ∂r ∂ρ ∂e T with entropy density per unit volume s(ρ, e), and where all functions after the first equality are evaluated at position r. It follows readily that the last equality is fulfilled for the pressure p defined in (3.15c). The other components of the degeneracy condition are satisfied trivially.


313

The reversible terms in the evolution equation of the momentum balance assume the form δE 3 ∂u(r) = Lu,k (r, r ) d r ∂t rev δxk (r ) k

=ρ

∂ ∂ ∂ v2 ∂ ∂ · (vu) − uγ vγ − e 1 − p , − ∂r 2 ∂r ∂r ∂r ∂r

(A.5)

where all functions after the last equal sign are evaluated at position r. Since the underlined terms cancel, one recovers the usual form of the momentum balance in the absence of viscous stresses. As far as the friction matrix is concerned, we demonstrate the degeneracy condition (2.3g). For example, one obtains for the uα -component, M (uα ,uγ ) (r, r )vγ (r )d 3 r + M (uα ,e) (r, r )d 3 r = ∂ ηαβγ T ∂rβ

∂δ 3 v d r + ∂r γ

δ

∂vγ ∂r

3

d r

= 0,

(A.6)

where in the second equality, a partial integration has been performed, and boundary terms are neglected. In an analogous way, it can be proven that the e-component of the degeneracy condition (2.3g) is satisfied.

Appendix B

ˆ

Derivation of L(Fαβ ,uγ ) (r, r ) in Eq. (5.12)

For deriving Eq. (5.12) in the example on elasto-viscoplasticity in Section 5.2, we introduce the quantity i = fij1 j2 j3 (B.1) j1 ,j2 ,j3

in the microscopic expression for the deformation gradient density (5.10b), representing the appropriately weighted number of quadruples that contribute to the average deformation gradient around particle i. One can then write Fˆ αβ (z; r) ∂rn,

=

N

δin

j1 ,j2 ,j3

i=1

+

3 ∂δ(r − ri ) 1 fij1 j2 j3 rjk i,α rˆj0k i,β ∂ri, i

N i=1

δ(r − ri )

k=1

3 1 fij1 j2 j3 δjk n − δin δα rˆj0k i,β . (B.2) i j1 ,j2 ,j3

k=1

314


Inserting this expression into (5.3) and using ∂uγ (z; r )/∂pn, = δγ δ(r − rn ), one obtains ˆ

L(Fαβ ,uγ ) (r, r ) % $N 3 ∂δ(r − ri ) 1 0 δ(r − ri ) fij1 j2 j3 rjk i,α rˆjk i,β = ∂ri,γ i i=1

+ δαγ

$N i=1

j1 ,j2 ,j3

1 δ(r − ri ) fij1 j2 j3 i j1 ,j2 ,j3

k=1

3

x

δ(r − rjk ) − δ(r − ri )

k=1

% rˆj0k i,β

. x

(B.3) With the aid of the approximation δ(r − rjk ) − δ(r − ri ) −

∂δ(r − ri ) rjk i,μ , ∂rμ

(B.4)

(Appendix B.3) can indeed be written in the form ˆ

L(Fαβ ,uγ ) (r, r ) = Fˆ αβ (r )

∂δ(r − r ) ∂δ(r − r ) Fˆ μβ (r). + δαγ ∂rγ ∂rμ

(B.5)

References Abraham, F. F. (1997a). On the transition from brittle to plastic failure in breaking a nanocrystal under tension. Europhys. Lett. 38, 103–106. Abraham, F. F., Schneider, D., Land, B., Lifka, D., Skovira, J., Gerner, J., and Rosenkrantz, M. (1997b). Instability dynamics in three-dimensional fracture: an atomistic simulation. J. Mech. Phys. Solids 45: 1461–1471. Alexander, S. (1998). Amorphous solids: their structure, lattice dynamics and elasticity. Phys. Rep. 296, 65–236. Allen, M. P., and Tildesley, D. J. (1987). Computer Simulation of Liquids. Clarendon Press, Oxford. Arsenlis, A., Parks, D., Becker, R., and Bulatov, V. V. (2004). On the evolution of crystallographic dislocation density in non-homogeneously deforming crystals. J. Mech. Phys. Solids 52, 1213–1246. Asaro, R. J. (1983). Micromechanics of crystals and polycrystals. In Advances in Applied Mechanics, vol. 23. (J. W. Hutchinson, and T. Y. Wu, Eds.), pp. 1–115. Academic Press, New York. Aubouy, M., Jiang, Y., Glazier, J. A., and Graner, F. (2003). A texture tensor to quantify deformations. Granular Matter 5, 67–70. Bagi, K. (2006). Analysis of microstructural strain tensors for granular assemblies. Int. J. Solids Struct. 43, 3166–3184. Beris, A. N., and Edwards, B. J. (1994). Thermodynamics of Flowing Systems with Internal Microstructure. Oxford University Press, Oxford.


315

Besseling, J. F., and Van der Giessen, E. (1994). In Mathematical Modelling of Inelastic Deformation, Applied Mathematics and Mathematical Computation 5 (R. J. Knobs, and K. W. Morton, Eds.), Chapman and Hall, London. Bird, R. B., Curtiss, C. F., Armstrong, R. C., and Hassager, O. (1987). Dynamics of Polymeric Liquids, vol. 2, Kinetic Theory, Second Edition. Wiley, New York. Boyce, M. C., Parks, D. M., and Argon, A. S. (1988). Large inelastic deformation of glassy polymers. Part I: rate dependent constitutive model. Mech. Mater. 7, 15–33. Buehler, M. J., Hartmaier, A., Gao, H. J., Duchaineau, M., and Abraham, F. F. (2004). Atomic plasticity: description and analysis of a one-billion atom simulation of ductile materials failure. Comput. Method Appl. Mech. Eng. 193, 5257–5282. Bulatov, V. V., Yip, S., and Argon, A. S. (1995). Atomic modes of dislocation mobility in silicon. Philos. Mag. A 72, 453–496. Bulatov, V. V., Abraham, F. F., Kubin, L., Devincre, B., and Yip, S. (1998). Connecting atomistic and mesoscale simulations of crystal plasticity. Nature 391, 669–672. Coleman, B. D., and Noll, W. (1960). An approximation theorem for functionals, with applications in continuum mechanics. Arch. Ration. Mech. Anal. 6, 355–370. Dafalias, Y. F. (1983). Corotational rates for kinematic hardening at large plastic deformations. J. Appl. Mech. 50, 561–565. Dafalias, Y. F. (1985a). A missing link in the macroscopic constitutive formulation of large plastic deformations. In Plasticity Today, Proceedings of an International symposium on current trends and results in plasticity, Udine, Italy, 27–30 June, 1983. (A. Sawczuk, and G. Bianchi, Eds.), Chapter 8, pp. 135–151. Elsevier, London. Dafalias, Y. F. (1985b). The plastic spin. J. Appl. Mech. T. ASME 52, 865–871. Dafalias, Y. F. (1998). Plastic spin: necessity or redundancy? Int. J. Plast. 14, 909–931. de Groot, S. R., and Mazur, P. (1962). Non-equilibrium Thermodynamics. North-Holland, Amsterdam. de Pablo, J. J., and Öttinger, H. C. (2001). An atomistic approach to general equation for the nonequilibrium reversible-irreversible coupling. J. Non-Newtonian Fluid Mech. 96, 137–162. El-Azab, A. (2000). Statistical mechanics treatment of the evolution of dislocation distributions in single crystals. Phys. Rev. B 61, 11956–11966. Evans, D. J., and Morriss, G. P. (1990). Statistical Mechanics of Nonequilibrium Liquids. Academic Press, London. Frenkel, D., and Smit, B. (2002). Understanding Molecular Simulation. Academic Press, London. Falk, M. L., and Langer, J. S. (1998). Dynamics of viscoplastic deformation in amorphous solids. Phys. Rev. E 57, 7192–7205. Gardiner, C. W. (1985). Handbook of Stochastic Methods for Physics, Chemistry and the Natural Sciences, Second Edition. Springer, Berlin. Geigenmüller, U., Titulaer, U. M., and Felderhof, B. U. (1983a). Systematic elimination of fast variables in linear systems. Phys. A 119, 41–52. Geigenmüller, U., Titulaer, U. M., and Felderhof, B. U. (1983b). The approximate nature of the OnsagerCasimir reciprocal relations. Phys. A 119, 53–66. Goldhirsch, I., and Goldenberg, C. (2002). On the microscopic foundations of elasticity. Eur. Phys. J. E 9, 245–251. Govaert, L. E., Timmermans, P. H. M., and Brekelmans, W. A. M. (2000). The influence of intrinsic strain softening on strain localization in polycarbonate: modeling and experimental validation. J. Eng. Mater. T. ASME 122, 177–185. Grabert, H. (1982). Projection Operator Techniques in Nonequilibrium Statistical Mechanics. Springer, Berlin. Grmela, M. (1984). Particle and bracket formulations of kinetic equations. Contemp. Math. 28, 125–132. Grmela, M. (1997). Workshop report. J. Non-Newtonian Fluid Mech. 69, 105–107. Grmela, M., and Öttinger, H. C. (1997). Dynamics and thermodynamics of complex fluids. I. Development of a general formalism. Phys. Rev. E 56, 6620–6632.

316


Groma, I. (1997). Link between the microscopic and mesoscopic length-scale description of the collective behavior of dislocations. Phys. Rev. B 56, 5807–5813. Groma, I., and Balogh, P. (1999). Investigation of dislocation pattern formation in a two-dimensional self-consistent field approximation. Acta Mater. 47, 3647–3654. Groma, I., Csikor, F. F., and Zaiser, M. (2003). Spatial correlations and higher order gradient terms in a continuum description of dislocation dynamics. Acta Mater. 51, 1271–1281. Hill, R. (1948). A theory of the yielding and plastic flow of anisotropic metals. Proc. Roy. Soc. A Lond. 193(1033), 281–297. Hirth, J. P., and Lothe, J. (1982). Theory of Dislocations. Wiley, New Work. Hoheisel, C., Vogelsang, R., and Schoen, M. (1987). Bulk viscosity of the Lennard-Jones fluid for a wide range of states computed by equilibrium molecular dynamics. J. Chem. Phys. 87, 7195–7198. Hoheisel, C., and Vogelsang, R. (1988). Thermal transport coefficients for one-and two-component liquids from time correlation functions computed by molecular dynamics. Comput. Phys. Rep. 8, 1–69. Hutchinson, J. W. (1976). Bounds and self-consistent estimates for creep of polycrystalline materials. Proc. Roy. Soc. Lond. A 348(1652), 101–127. Hütter, M., and Tervoort, T. A. (2008a). Finite anisotropic elasticity and material frame indifference from a nonequilibrium thermodynamics perspective. J. Non-Newtonian Fluid Mech. 152, 45–52. Hütter, M., and Tervoort, T. A. (2008b). Thermodynamic considerations on non-isothermal finite anisotropic elasto-viscoplasticity. J. Non-Newtonian Fluid Mech. 152, 53–65. Ilg, P. (2008). (private communication). Irving, J. H., and Kirkwood, J. G. (1950). The statistical mechanical theory of transport processes. IV. The equations of hydrodynamics. J. Chem. Phys. 18, 817–829. Jelić, A., Hütter, M., and Öttinger, H. C. (2006). Dissipative electromagnetism from a nonequilibrium thermodynamics perspective. Phys. Rev. E 74, 041126-1–8. Jongschaap, R. J. J., and Öttinger, H. C. (2001). Editorial: nonequilibrium thermodynamics and complex fluids. J. Non-Newtonian Fluid Mech. 96, 1–3. Krausz, A., and Eyring, H. (1975). Deformation Kinetics. Wiley-Interscience, London. Kreuzer, H. J. (1981). Nonequilibrium Thermodynamics and Its Statistical Foundations. Clarendon Press, Oxford. Kröger, M., Hütter, M., and Öttinger, H. C. (2001). Symbolic test of the Jacobi identity for given generalized ‘Poisson’ bracket. Comput. Phys. Commun. 137, 325–340. Kubo, R., Toda, M., and Hashitsume, N. (1991). Nonequilibrium Statistical Mechanics, vol. II of Statistical Physics, Second Edition. Springer, Berlin. Larson, R. G. (1988). Constitutive Equations for Polymer Melts and Solutions. Butterworth Publishers, Stoneham. Le Bellac, M., Mortessagne, F., and Batrouni, G. G. (2004). Equilibrium and Non-equilibrium Statistical Thermodynamics. Cambridge University Press, Cambridge. Li, J., Van Vliet, K. J., Zhu, T., Yip, S., and Suresh, S. (2002). Atomistic mechanisms governing elastic limit and incipient plasticity in crystals. Nature 418, 307–310. Lifshitz, E. M., and Pitaevskii, L. P. (1980a). Statistical Physics I, vol. 5 of Landau and Lifshitz: Course of Theoretical Physics, Third Edition. Pergamon, Oxford. Lifshitz, E. M., and Pitaevskii, L. P. (1980b). Statistical Physics II, vol. 9 of Landau and Lifshitz: Course of Theoretical Physics, Second Edition. Pergamon, Oxford. Loret, B. (1983). On the effects of plastic rotation in the finite deformation of anisotropic elastoplastic materials. Mech. Mater. 2, 287–304. Marsden, J. E., and Ratiu, T. S. (1999). Introduction to Mechanics and Symmetry. Springer, Berlin. Morrison, P. J. (1998). Hamiltonian description of the ideal fluid. Rev. Mod. Phys. 70, 467–521. Nabarro, F. R. N. (1967). Theory of Crystal Dislocations. Oxford University Press, Oxford. Naghdi, P. M., and Srinivasa, A. R. (1993). A dynamical theory of structured solids. I. Basic developments. Philos. Trans. R. Soc. Lond. A 345, 425–458. Orowan, E. (1934). Plasticity of crystals. Z. Phys. 89, 605–659.


317

Öttinger, H. C. (1996). Stochastic Processes in Polymeric Fluids. Springer, Berlin. Öttinger, H. C., and Grmela, M. (1997). Dynamics and thermodynamics of complex fluids. II. Illustrations of a general formalism. Phys. Rev. E 56, 6633–6655. Öttinger, H. C. (1998). General projection operator formalism for the dynamics and thermodynamics of complex fluids. Phys. Rev. E 57, 1416–1420. Öttinger, H. C. (2005). Beyond Equilibrium Thermodynamics. Wiley, Hobroken. Öttinger, H. C. (2007). Systematic coarse graining: “Four Lessons and A Caveat” from nonequilibrium statistical mechanics. MRS Bull. 32, 936–940. Pan, J., and Rice, J. R. (1983). Rate sensitivity of plastic-flow and implications for yield-surface vertices. Int. J. Solids Struct. 19, 973–987. Parr, R. G., and Yang, W. (1989). Density-Functional Theory of Atoms and Molecules. Oxford University Press, Oxford, Appendix A. Peirce, D., Asaro, R. J., and Needleman, A. (1983). Material rate depenence and localized deformation in crystalline solids. Acta Metall. 31, 1951–1976. Rice, J. R. (1971). Inelastic constitutive relations for solids: an internal variable theory and its application to metal plasticity. J. Mech. Phys. Solids 19, 433–455. Rubin, M. B. (1994). Plasticity theory formulated in terms of physically based microstructural variables part 1. Theory. Int. J. Solids Struct. 31, 2615–2634. Rubin, M. B. (1996). On the treatment of elastic deformation in finite elasticviscoplastic theory. Int. J. Plast. 12, 951–965. Smith, P. E., and van Gunsteren, W. F. (1993). The viscosity of SPC and SPC/E water at 277 and 300 K. Chem. Phys. Lett. 215, 315–318. Spencer, A. J. M. (1971). Part III. Theory of invariants. In Continuum Physics, vol. 1. Mathematics (A. C. Eringen, Ed.), pp. 239–353. Academic Press, New York. Steenbrink, A. C., Van der Giessen, E., and Wu, P. D. (1997). Void growth in glassy polymers. J. Mech. Phys. Solids 45, 405–437. Taylor, G. I. (1934). Plastic deformation of crystals. Proc. R. Soc. Lond. Sec A 145, 362–404. Tervoort, T. A., Klompen, E. T. J., and Govaert, L. E. (1996). A multimode approach to finite, threedimensional, nonlinear viscoelastic behavior of polymer glasses. J. Rheol. 40, 779–797. Tervoort, T. A., Smit, R. J. M., Brekelmans, W. A. M., and Govaert, L. E. (1998). A constitutive equation for the elasto-viscoplastic deformation of glassy polymers. Mech. Time-Dep. Mater. 1, 269–291. Tervoort, T. A., and Govaert, L. E. (2000). Strain-hardening behavior of polycarbonate in the glassy state. J. Rheol. 44, 1263–1277. Truesdell, C., and Noll, W. (1992). The Non-Linear Field Theories of Mechanics, Second Edition. Springer, Berlin. Van der Giessen, E. (1991). Micromechanical and thermodynamic aspects of the plastic spin. Int. J. Plast. 7, 365–386. Von Polanyi, M. (1934). Lattice distortion which originates plastic flow. Z. Phys. 89, 660–662. Wang, C. C. (1970). A new representation theorem for isotropic functions: an answer to Professor G. F. Smith’s criticism of my paper on ‘representations for isotropic functions.’ Arch. Ration. Mech. Anal. 36, 198–223. Wang, C. C. (1971). Corrigendum to my recent papers on ‘representations for isotropic functions.’ Arch. Ration. Mech. Anal. 43, 392–395. Zimmerman, J. A. (1999). Continuum and Atomistic Modeling of Dislocation Nucleation at Crystal Surface Ledges. PhD thesis, Stanford University, Palo Alto. Zhou, M. (2003). A new look at the atomic level virial stress: on continuum-molecular system equivalence. Proc. R. Soc. Lond. Sec A 459(2037), 2347–2392.

Subject Index An italic f (or t) following a page number indicates that the material referred to is in a figure caption (or table)

Ab initio simulations, for elastic constants, 58 AlMg1Si0.6 foam electrical conductivity of, 185t microstructure of, 183f Young’s modulus of, 186t, 187f Aluminum CTE of nanopore surface, 45 with spherical nanovoids, elastic moduli of, 39, 45 surface elastic modulus of, 54 Aluminum 3003-H18, 191, 191t Aluminum 2124-T351, 191, 191t Anisotropic inhomogeneities cross-property connections for, 155 materials with parallel, 156–200 Anisotropic porous materials macroscopic strain, 227–229 plastic yield of, 225 Anisotropy, 101, 108 conductive, 146, 148 elastic, 125, 131, 146, 148 isotropic approximation of, 240 Annular crack, 111f Approximately parallel inhomogeneities, 161–164 Asymptotic homogenization method, 177, 244 Atomistic calculations, 3, 59, 458 Average strain, 36 defined, 31–32 deriving volume, in RVE, 41, 43 Average stress, 36 defined, 31–32 deriving volume, in RVE, 41, 43 Axisymmetric deformation mode, 36, 42

Berryman–Milton’s bounds, 82–85, 90, 92 Boundary conditions, 10, 16, 23, 34, 37 for CCA and GSCM, 50 on surface of cylindrical pore, 49 Bristow’s cross-property connection, 91 Bristow’s elasticity–conductivity connection, for microcracked material, 74–76 Bristow’s hypothesis, 148 Brittle fracture versus effective elasticity, 153–154 Bulk modulus, 20, 22, 25, 37, 113, 123, 155 of composite with spherical nano-inhomogeneities, 35 to conductivity, 92 cross-property connections involving, 76–79 by CSA, prediction of, 35 2D, 103 as function of void radius, 39f transverse and effective plane-strain, 50, 54 Bulk modulus-conductivity bounds, for 3D isotropic composites, 86 Bulk modulus-conductivity connection, 80 Carbon fibers, 192 Cartesian coordinate system, 34, 48 Cauchy–Green strain tensor, 272–273 Cauchy stress, of surface, 8 Cauchy stress tensor, 272, 278 CCA model. see Composite cylinder assemblage model Circular crack, 110, 111f Circular Hertzian contact, 211, 224

Balance laws, 272 BaTiO3 fibers, 175f , 177 Beran–Molyneux’ bounds, 84–85 319

320

Subject Index

Clausius–Duhem inequality, 272 Closed-cell aluminum foams, 183–190 Coarse-grained variables, 282, 288 Coarse graining applications of, 288–308 in elasto-viscoplasticity, 291–308 ensembles, 281–283 generators, 283–284 GENERIC framework, 279–288 irreversible effects upon, 285 in microscopic Hamiltonian point mechanics, 281–287 in nonisothermal compressible hydrodynamics, 288–291 operators, 284–288 time scale separation between different levels, 279, 280f, 285 Coefficient of thermal expansion (CTE), 9, 22–23, 41 of aluminum nanopore surface, 45 of cylindrical fibers, 42 expression relating effective elastic moduli and, 44 of heterogeneous medium, 40, 44–45 Coefficient of thermal expansion (CTE), effective of cylindrical nanopores, 46f of spherical nanopore composites, 45, 46f of spherical parallel cylindrical nanopores, 45 Colloidal particle, 279, 285 Compliance–resistivity connections, 137–138, 143, 157, 164, 167 Compliance tensor, of composite, 32–33 Composite cylinder assemblage (CCA) model, prediction of longitudinal modulus by, 51 longitudinal shear modulus by, 51–52 Poisson’s ratio by, 51 transverse bulk modulus by, 50 transverse shear modulus by, 52 Composite sphere assemblage (CSA) model, prediction of, elastic moduli by, 34–35 Conductive-magnetic bounds, 85 Conductivity–elasticity connection, 152

Conductivity law, 87 Conductivity measurements, 183 Constitutive theory, 8 Continuum mechanics, 3–5, 44 Continuum theory. see Continuum mechanics Coplanar cracks, 148 Crack density, 74–75 parameters, 97–98, 107 scalar, 97 Crack density tensors, 95, 97, 110–111 components of, 109 2D, 107 3D, 108 Cracks annular, 111f circular, 110, 111f coplanar, 148 effective elastic properties, 97, 154 flat elliptical, 110 of irregular shapes, 110–111, 149 materials with, 143–144 penny-shaped, 75 quantitative characterization of, 106–111 stacked, 148 three-dimensional solid with circular, 108–109 two-dimensional elliptic holes, 111–113 two-dimensional solid with rectilinear, 106–108 Critical radii of cylindrical QW, 29 of spherical QD, 29 Cross-property bounds, 74, 80–92 comparison of different, 91f construction of, 87–91 Gibiansky-Torquato’s translation-based, 85–91 Cross-property connections, 72–73 advantages, 155–156 for anisotropic inhomogeneities, 155–160 for anisotropic two-phase composites, 133–155 applications of, 182

Subject Index approaches to, 74–95 Bristow, comparison, 91 effect of interactions on, 148–149 electric and thermal conductivities, connection between, 152–153 empirical observations on, 94–95 involving bulk modulus, 76–79 Levin’s formula, 76–78 Lutz–Zimmerman’s result, 79 materials science problems, 182 NIA-based, 182 nonspheroidal inhomogeneity shapes on, 149 physical properties, 153–155 for piezoelectric fiber-reinforced composites, 92–94 quantitative connections, 153–155 quantitative theoretical results on, 72 Rosen–Hashin’s formula, 78 for rough surface, 210 verification of, 204–207, 239 Crystal plasticity, 303 CSA model. see Composite sphere assemblage model CTE. see Coefficient of thermal expansion Cyclic loading- and manufacturing-related damage, 195–198 Cylindrical coordinate system, 48–52 Cylindrical fibers elastic constants of, 42 generalized Levin’s formula for, 41–45 Hill’s connections for, 41–45 Deformation, 3–4. See also Elastic deformation; Plastic deformation axisymmetric, 36, 42 hydrostatic, 35, 40–41 infinitesimal, 8 mode of, 40–41 in RVE of heterogeneous material, 40 uniform, 41–42 Deformation gradient, 271 fluctuations in, 299 macroscopic measure of, 292 microscopic expression for, 291–294

321

Deformation gradient density, 293, 295, 299 Dilute concentration approximation, 32–33 Dirac delta function, 268, 293 Dislocation nucleation, in QDs, variation of critical radii for, 30f Dislocations, 281, 285 2D isotropic composites, elasticity–conductivity bounds for, 86 3D isotropic composites, 87 bulk modulus-conductivity bounds for, 86 Dissipative bracket, 260 Dissipative effects, 257, 297, 302, 306 Dual tensors, 127 Effective conductivity, microstructural parameters for, 102–133 Effective elasticity versus effective permeability, 153–154 microstructural parameters for, 102–133 Eigenstrain, 9 dilatational, 15 misfit, 24, 27 uniform, 9–11, 22–23 Elastic and conductive anisotropies, 239 connection between the degrees of, 146–148 Elastic and conductive properties, 200 effects of “islands” on, 203 Elastic and inelastic deformations balance equations, 272 kinematics and kinetics, 271 Elastic constant. see Elastic moduli Elastic deformation, 276 Elastic deformation gradient, 276 evolution equation for, 277 fluctuations in, 297, 300 transversely isotropic fluctuations in, 304–307 viscoplastic relaxation of, 276 Elasticity–conductivity bounds, for 2D isotropic composites, 86

322

Subject Index

Elasticity–conductivity connections, 80, 135–141, 191, 196, 210–225 Bristow’s, for microcracked material, 74–76 contact of rough surfaces, 210 sensitivity of, 145–146 Elasticity–conductivity constraints, 149–152 Elasticity tensor, 103, 125 Elastic moduli, 5, 14, 24, 31, 40–41, 74, 84, 183 ab initio simulations for, 58 of aluminum with spherical nanovoids, 39, 45 of bulk ZnS and CdS, 25 of composite with spherical nanoinhomogeneities, 34–40 of cylindrical fibers, 42 expression relating, 43 surface, 8, 20, 39, 53–54 tailoring of, nanochannel-array materials, 47–48, 53–57 Elastic moduli, prediction of by CSA, 34–35 by GSCM, 37 by MTM, 36–37 nanochannel-array materials, 48–53 Elastic strains, 22 distribution of normalized, in QDs, 28f in embedded spherical alloyed QD, 25 in matrix, 22 in multi-shells, 22 normalized, 26f normalized biaxial, 27f Elasto-viscoplasticity, 278, 305 coarse graining in, 291–308 Electrical conductivity, 152–153 of AlMg1Si0.6 foam, 185t Ellipsoidal inhomogeneity, 128 Elliptic functions, 244–246 Elliptic Hertzian contact, 211–214 incremental compliances of, 214 normal and tangential compliances, 212–213 resistance of, 213 two cylinders, 214f

Entropy, 260, 265, 267, 274, 284, 289 Eshelby formalism application of, 19–30 for nano-inhomogeneities, 4–5, 9–19 Eshelby formula, 38 with interface stress effect, 18–19 for nano-inhomogeneity, 18–19 Eshelby tensors, 9–15, 22, 61, 105, 114, 116, 128 exterior, 13 in inhomogeneous inclusion, 13, 15 with interface stress, 14 interior, 12–14 scaling laws for interior, 61 transversely isotropic, 12 Euclidean norm, 160, 194, 240 Explicit elasticity–conductivity connections, 75 Falk–Langer-type expression, 295 Fiber orientations, 160 Fiber-reinforced composites, 168 piezoelectric, 74, 169 uniaxial, 93 Fick’s law of heat conduction, 297 Finite anisotropic thermoelasticity, 273–276 evolution equations for, 275 structural and hydrodynamic variables, 273 Finite element method, 4 Finite nonisothermal anisotropic elasto-viscoplasticity, 276–279 Flat elliptical cracks, 110 Fluctuation–dissipation theorems. see Green–Kubo relations Fourth-rank tensors, 87, 100, 102, 108, 156, 241–243 Fracture–elasticity, 153 Free energy, surface/interface, 8 Free-surface properties, 39 Friction matrix, 260–262, 265, 277 based on Onsager’s regression hypothesis, 290–291 irreversible dynamics, 297–303 microscopic expression for, 286–287

Subject Index Gaussian distribution, 145, 223, 238 General equation for the nonequilibrium reversible–irreversible coupling framework. see GENERIC framework Generalized canonical ensembles, 282 Generalized Levin’s formula for cylindrical fibers, 41–45 for spherical particles, 40–41 for two-phase heterogeneous medium, 40–41 Generalized microcanonical ensemble, 282 Generalized self-consistent method (GSCM), prediction of, 31–32, 34 elastic modulus by, 37, 49 longitudinal modulus by, 51 longitudinal shear modulus by, 51–52 Poisson’s ratio by, 51 transverse bulk modulus by, 50 GENERIC framework applications of, 263–279 coarse graining, 279–288 evolution equation, 263 finite anisotropic thermoelasticity, 273–276 finite nonisothermal anisotropic elasto-viscoplasticity, 276–279 of nonequilibrium thermodynamics, 259–263 reversible dynamics in, 261 Gibbs–Thomson equation, 62 Gibiansky-Torquato’s translation-based cross-property bounds, 85–91 Green–Kubo relations, 257, 286, 297, 301 GSCM. see Generalized self-consistent method Gurtin–Murdoch theory, 4 Hamiltonian point mechanics, 260, 263–266 coarse graining, 281–287 Hamilton’s equations of motion, 265 Hashin–Shtrikman’s (HS) bounds, 72, 79, 91, 229 Heat flux, 270, 273, 278, 290 Hertzian contacts, 210, 220

323

of circular shape, 211 compliance tensor, 219 of elliptic shape, 211–214 versus “welded” areas, 214–220 Hill’s connections, for cylindrical fibers, 41–45 Hill’s theorem, 131–133 Homogenization method, asymptotic, 177, 244 Hooke’s law, 87 Hoop stress, normalized, 20 H-tensors, 104–105, 116–117, 119, 123, 130–131 Hydrostatic deformation, 35, 40–41 Hydrothermal aging-induced damage, 198–200 Hyperbolae bounds, 89 Infinitesimal analysis, 8 Infinitesimal elasticity, theory of, 24 Inhomogeneity anisotropic, 155–200 contributions, individual, 96 on cross-property connections, 148–149 of diverse shapes, 98 ellipsoidal, 128 of irregular shapes, 131–133 isotropic, 155 materials with isolated, 102–133 in NIA, 127 nonrandomly oriented, 98 parallel, 156 shapes, 145–148 spheroidal, 115–126, 128 three-dimensional, 113–115 volume fraction of, 97 Inhomogeneity boundaries, jaggedness of, 132, 134f Inhomogeneity–matrix contrast, 155–156 Inhomogeneous inclusion, 9 Eshelby tensor in, 13, 15 Interface compliance tensor, 221 Interface conditions, 10, 16, 23 Interface stress, 2–3, 22, 35, 43 with Eshelby formula, 18

324

Subject Index

micromechanical framework for nano-inhomogeneities with, 30–34 Interface stress effects, 15–16, 18–19, 22, 31, 37 constant, 22 on cylindrical fibers, 44 on spherical nanoparticles, 41 Interface stress model (ISM), 9 equivalence between interphase models and, 45–47 Interphase models for displacement and stress, 47 and ISM, equivalence between, 45–47 Irregularity factors, on elastic and conductive properties, 134f Irregular shapes, inhomogeneity of, 131–133 ISM. see Interface stress model Isotropic composites bulk modulus-conductivity bounds for 3D, 87 elasticity–conductivity bounds for 2D, 86 two-phase, 76–77, 82 Isotropic conductivity, 101 Isotropic elasticity, 101 Isotropic inhomogeneities, 155 nonlinear connections for, 164–168 Isotropic parallel inhomogeneities, 158 Isotropic tensors, fourth-rank, 87 Isotropy cases of, 100–101, 141–143 transverse, 147f Jacobi identity, 261, 269, 287, 296 Jaggedness of inhomogeneity boundaries, 132, 134f Kanaun–Levin’s effective field method (KLS), 168, 187 Kronecker delta, 268 K-tensors, 130–131 Lagrange parameters, 283–284 Lattice constants, 22, 24–25 Legendre polynomials, 11

Levin’s formula, extension to anisotropic materials, 76–78 Levin’s formula, generalized for cylindrical fibers, 41–45 for spherical particles, 40–41 for two-phase heterogeneous medium, 40–41 Linear conduction law, 127 Linear constitutive equations, 8, 92 Linear drag force, single particle in spring potential with, 264–266 Linear elastic model, 103 Linear response theory, 291 Local field theories, 263 Longitudinal modulus determining, 51 predicted by CCA and GSCM models, 51 Longitudinal shear modulus, 51–52, 54. see also Transverse bulk modulus predicted by CCA and GSCM models, 51–53 ratio of specific effective, 55–56f Macroscopic continuum theory, 285 Macroscopic elasticity, 291 Macroscopic strain, 227–229 Mass density, 276 Materials science problems, 182 Melting temperature size-dependent, 62 of spherical nanoparticles, 62 Microcracked material, Bristow’s elasticity-conductivity connection for, 74–76 Microcracked metals, 191–192 elasticity–conductivity connection for, 191 Young’s modulus of, 192f Microcracks, of orientation distribution, 202 Microgeometry, 82 Micromechanical framework, for nano-inhomogeneities application of, 34–57 with interface stress, 30–34 Microscopic variables, 282

Subject Index Microstructural parameters, 83, 97–99 benefits of, 101–102 for conductive properties, 126–131 for effective elasticity and effective conductivity, 102–133 for elastic properties, 126–131 identification of, 101 limitations of, 98 in non-interaction approximation, 99–100 Microstructures, 200 of AlMg1Si0.6 foam, 183f quantitative characterization of, 95–102, 200–203 of YSZ coatings, 201f Milton’s inequality, 80–82 Misfit prismatic dislocation (MD) loop, 29 Misfit strains, 23–25, 29 Moderate orientation scatter, 160–161 Molecular dynamic simulations for calculating effective moduli of nano-aluminum, 39 for CTE of nanoslab surface, 44 for elastic constants, 58 for free-surface elastic moduli of aluminum, 45 Mori–Tanaka method (MTM), 31, 34, 187–188 prediction of elastic moduli by, 36–37 Multiple elliptic contacts, 220 Multi-shell structures, strain distributions in QDs with, 23 Nanocellular material, effective longitudinal shear modulus of, 55–56f Nanochannel-array materials with aligned cylindrical nanopores, 48f, 49 application of, 48 prediction of elastic moduli of, 48–53 properties of, 48 tailoring of elastic moduli of, 53–57 Nanocomposite effective elastic moduli of, 32 effective stiffness tensor of, 32

325

shear modulus of, 36–37 Nano-inhomogeneities application of micromechanical framework for, 34–57 elastic moduli of solids with spherical, 34–40 Eshelby formalism for, 4–19 predicting bulk modulus of spherical, 35 Nanoparticles, size dependence of melting temperature of, 62 Nanoporous materials ratios of specific effective moduli of, 55 stiffness of, 56 Nanovoid, 61 radius of, 39–40 stress concentration factor of spherical or circular, 19–21 NIA. see Non-interaction approximation Nonequilibrium thermodynamics GENERIC framework of, 259–263 reversible and irreversible terms, separation of, 259 Non-interaction approximation (NIA), 73, 75, 134 framework of, 168 microstructural parameters rooted in, 99–100 multiple inhomogeneities in, 127 Nonisothermal hydrodynamics, 266–271 coarse graining in, 288–291 evolution equations, 270, 290 Nonlinear connections, for parallel isotropic inhomogeneities, 164 Nonrandomly oriented inhomogeneities, 98 Nonspheroidal inhomogeneity, shapes on cross-property connections, 148–149 N-tensors, 105, 113, 116, 120, 123, 130 Ohmic resistance, 287 Onsager–Casimir symmetric, 261 Onsager’s regression hypothesis, 287 friction matrix based on, 290–291 Orientation distribution, 109f , 168, 238 of microcracks, 202

326

Subject Index

Orientation scatter, moderate, 160–161 Orthotropy, 108, 125, 147f Parallel anisotropic inhomogeneities cross-property connections for, 156–200 materials with, 156–200 Parallel inhomogeneities, 156, 161–164 Parallel isotropic inhomogeneities, nonlinear connections for, 164–168 Penny-shaped crack, 75 Permeability-elasticity, 153 Piezoelectric fiber-reinforced composites, 207 cross-property connections for, 92–94 Piezoelectric material constants, 169–172, 172t, 210 of Araldite matrix, 176f of PZT-5H, 175f Piola–Kirchhoff stress, surface, 8 Piola–Kirchhoff stress tensor, 305 Plastic deformation, 276, 278 in crystals, 303 rate-dependent, 276 relation to microscopic computer simulations of, 307–308 volume conservation upon, 298–299 Plastics, short fiber-reinforced, 195 Plastic spin, 306 Plastic velocity gradient tensor, 276–277, 302 symmetric and antisymmetric parts of, 306 tensorial structure of, 304 Plastic yield effective conductivities, 230–234 of porous materials, 225 porous space characteristics, 229–230 Poisson brackets, 260–261, 264 Poisson operator, 260, 262, 264, 268, 274, 284, 289 reversible dynamics, 294–296 Poisson’s ratio, 51, 53–54, 81 predicted by CCA and GSCM models, 51 Poly(phenylene sulfide) (PPS), 192

reinforced by carbon fibers, 194, 197t reinforced by glass fibers, 194, 199f , 199t Porosity, 53–54, 55f , 56, 56f Porous materials cases of overall isotropy, 234 elastic–plastic behavior of, 226f macroscopic strain, 227–229 plastic yield of, 225 stress–strain curves for, 228f Powder metallurgy processing, 183 Projection operator method, 285–286 PZT-7A fibers, 176f , 177 Quantum dots (QDs). see also Quantum wire (QW) continuous optical tuning of, 26 critical radii of spherical, 29 critical sizes of alloyed, 27–30 distribution of normalized biaxial strain in free-standing, 27 self-capping alloyed, 30 strain distributions in alloyed, 23–27 variation of critical radii for dislocation nucleation in, 30f Quantum wire (QW), critical radii of cylindrical, 29 Rate-dependent plastic deformation, 276 Representative volume element (RVE), 31, 40 of heterogeneous medium, 41 volume average strain in, 41, 43 volume average stress in, 41, 43 Resistivity/conductivity tensors, 162 Resistivity contribution tensor, 127 Rosen–Hashin’s formula, 78–79 Rough surfaces, contact of, cross-property connection, 210 R-tensors, 127, 130–131 RVE. see Representative volume element Scalar crack density, 97 Scaling laws for interior Eshelby tensor, 61 of maximum stress concentration factor, 60, 60f

Subject Index for properties of nanostructured materials, 57–63 Second-rank crack density tensor, 97–98 Second-rank Eshelby’s tensor, 128 Second-rank symmetric tensor, 101, 107–108, 112 Semiconductor QDs. see Quantum dots (QDs) Shear modulus, 22, 81–83, 123, 143f , 155 to conductivity, 92 effective plane-strain, 50 longitudinal, 51–52 of nanocomposite, 36–37 predicted by CCA and GSCM models, 51–53 transverse, 52–53 Shear stiffness, 54 Short fiber-reinforced plastics, 195 absence of voids and cracks, 196 changes in properties, 195 cyclic loading- and manufacturing-related damage, 195–198 elasticity–conductivity connection, 196 hydrothermal aging-induced damage, 198–200 Short fiber-reinforced thermoplastics, 192–195 Slip systems, 303 Spherical inhomogeneity in infinite medium, 10f stress concentration tensors for, 16 Spherical particles generalized Levin’s formula for, 40 melting temperature of, 62 Spheroidal inhomogeneities, 115–126, 128 Stacked cracks, 148 Stiffening effect, 54–55 application of nanoporous materials by, 56 Stiffness–conductivity connections, 157, 159 Stiffness tensor, effective, of nanocomposite, 32–33 Strain concentration tensors, 32–34

327

Strain distributions in alloyed QDs, 23–27 in QDs with multi-shell structures, 23 Strain energy, 18, 38 Strain field, 9, 12, 15 Strain tensor, 22 Stress concentration decrease of, 20 as function of surface properties, 21f Stress concentration factor scaling law of maximum, 60 of spherical or circular nanovoid, 19–21 Stress concentration tensors, 15–18, 61 defined, 33 in inhomogeneity, 16–17 with interface stress effect, 16 in matrix, 17 Stress discontinuity, 19 Stress fields, 16, 19–20 Stress intensity factors (SIFs), 153, 215 Stress tensors, 38, 273, 275, 290 Cauchy and the Piola–Kirchhoff, 8 Stress triaxiality, 20 Surface constitutive equation, 49 Surface elasticity. see Surface elastic modulus Surface elastic modulus, 20, 39, 55, 59 of aluminum, 54 on effective CTEs of nanopore composite, 45 Surface/interface atoms, 22 profound effect of, 22, 24, 57 Surface/interface effect, 8–9, 40 Surface/interface equations, of elasticity, 7 Surface/interface stress, 2–4 Surface parameter, mixed, 54, 55f , 56, 56f Surface stress, 2–3, 25, 50 Surface stress effects, 4–5, 19–22, 59–60 on CTE, 45 on effective bulk and shear moduli, 39–40 elastic properties with, 58–61 on stress concentration, 20–21

328

Subject Index

Tangential anisotropy, 223 Thermal conductivities, 152–153 Thermal expansion coefficient, 24, 76–77 Thermodynamics, second law of, 272 Thermoelastic constitutive relation, 9 of cylindrical fibers and matrix, 42 Thermoelasticity. see also Finite anisotropic thermoelasticity basic equations to solve boundary value problems of, 6 constitutive equations of, 76 effect of, on effective CTEs of nanopore composite, 45 Thermoplastics, short fiber-reinforced, 192–195 Three-dimensional inhomogeneities, 113–115 Three-dimensional solid with circular cracks, 108–109 Three-point correlation function, 82–83 Total angular momentum, 271 Total energy, 260, 264–265, 267, 274, 297 Total mass, 271 Total momentum, 271 Translation tensor, 86, 88 Transverse bulk modulus, predicted by CCA and GSCM models, 50 Transverse isotropy, 141–143, 147f Transversely isotropic fourth-rank tensors, 241–243 Transversely isotropic piezoelectric constituents, fiber-reinforced composites with, 168–182 Transversely isotropic system, 304–307 Transverse shear modulus, predicted by CCA and GSCM, 52–53 Two-dimensional elliptic holes, 111–113 Two-dimensional solid with rectilinear cracks, 106–108 Two-phase isotropic composites, 76–77, 82

explicit cross-property connections for anisotropic, 133–155 properties of, 80 Uniaxial fiber-reinforced composites, 93 Universal bounds, 73 Vegard’s law, 23–24 Viscoelastic behavior, linear and nonlinear, 278 Viscous stress tensor, 270 Void radius, spherical, 39–40 for different stress triaxialities, 21 effective bulk modulus as function of, 39f Void size, 20, 45 Volume average strain, in RVE, 41, 43 Volume average stress, in RVE, 41, 43 Volume fraction, 73, 79, 98 inhomogeneities, 97 of spheres, 101, 105 “Welded” areas, Hertzian contacts versus, 214–220 White noise, 298 Wiener process, 298 Yield point, 225–226 Yield stress, 227, 230, 278 of porous metal, 225 Young–Laplace equation generalized, for solids, 7 Lagrangian and Eulerian description of, 7 Young modulus, 4, 105, 113, 143f , 159, 183 of AlMg1Si0.6 foam, 186t, 187f versus inverse of number of atomic layers, 59f of microcracked metals, 192f of nanoplate, 58 Y-tensor, 86–88 Yttria-stabilized zirconia (YSZ) coatings, 201f , 202

Advances in Applied Mechanics, Volume 42

Advances in applied mechanics. Vol. 42

Advances in Applied Microbiology, Volume 42