Biohydrogen: For Future Engine Fuel Demands

Green Energy and Technology

Ayhan Demirbas

Biohydrogen For Future Engine Fuel Demands

123

Ayhan Demirbas, Professor of Energy Technology Sila Science and Energy Trabzon Turkey

ISSN 1865-3529 ISBN 978-1-84882-510-9 e-ISBN 978-1-84882-511-6 DOI 10.1007/978-1-84882-511-6 Springer Dordrecht Heidelberg London New York British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library Library of Congress Control Number: 2009929234 © Springer-Verlag London Limited 2009 Apart from any fair dealing for the purposes of research or private study, or criticism or review, as permitted under the Copyright, Designs and Patents Act 1988, this publication may only be reproduced, stored or transmitted, in any form or by any means, with the prior permission in writing of the publishers, or in the case of reprographic reproduction in accordance with the terms of licences issued by the Copyright Licensing Agency. Enquiries concerning reproduction outside those terms should be sent to the publishers. The use of registered names, trademarks, etc. in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant laws and regulations and therefore free for general use. The publisher makes no representation, express or implied, with regard to the accuracy of the information contained in this book and cannot accept any legal responsibility or liability for any errors or omissions that may be made. Cover design: WMXDesign, Heidelberg, Germany Printed on acid-free paper Springer is part of Springer Science+Business Media (www.springer.com)

Preface

Today’s world faces three critical problems: (1) high fuel prices, (2) climatic changes, and (3) air pollution. Experts suggest that current oil and gas reserves are only sufficient to last a few more decades. It is well-known that transport is almost totally dependent on fossil fuels, particularly petroleum-based fuels such as gasoline, diesel fuel, liquefied petroleum gas, and compressed natural gas. Petroleumbased fuels are well-established products that have served industry and consumers for more than one hundred years, and for the foreseeable future, automotive fuels will still be largely based on liquid hydrocarbons. However, time is running out and petroleum, once considered inexhaustible, is now being depleted at a rapid rate. As the amount of available petroleum decreases, the need for alternate technologies to produce liquid fuels that could potentially help prolong the liquid fuels culture and mitigate the forthcoming effects of the shortage of transportation fuels increases. There are several reasons for biofuels to be considered as relevant technologies by both developing and industrialized countries. They include energy security reasons, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sectors of all countries in the world. This book discusses the production, storage, transportation, usage, economy, policy, and environmental impacts of biohydrogen. Biohydrogen is a replacement for fossil and biorenewable liquid fuels. In this book, the modern biomass-based transportation fuels bioethanol, biomethanol, biodiesel, bio-oil, biogas, and biohydrogen are briefly reviewed. Biomass conversion technologies are important for obtaining biofuels such as bioethanol, biodiesel, bio-oil, and biohydrogen. A comprehensive definition of biohydrogen is hydrogen produced chemically, thermochemically, biologically, biochemically, and biophotolytically from all biomass materials. Biohydrogen is a renewable biofuel produced from biorenewable feedstocks by chemical, thermochemical, biological, biochemical, and biophotolytical methods. Biohydrogen is an environmentally friendly alternative automotive fuel that can be used in an internal combustion engine. Hydrogen can be produced from biorenewable feedstocks via thermochemical conversion processes such as pyrolysis, gasification, steam gasification, steam reforming of bio-oils, and supercritical water gasification (SWG) of biomass. Hydrogen can also be produced by renewable biological systems. For example, there are three types of microorganisms that generate hydrogen: cyanobacteria, anaerobic bacteria, and fermentative bacteria. The hydrogen economy is a vision for a future in which hydrogen replaces fossil fuels. Economically, the wasteful hydrogen process translates to electricity from v

vi

Preface

hydrogen and fuel cells costing at least four times as much as electricity from the grid. In fact, electricity would be used much more efficiently if it were sent directly to the appliances instead. The transition to a hydrogen economy would require a huge investment in new infrastructure to produce, store and deliver hydrogen to end-users, to establish hydrogen stationary systems, as well as to develop and manufacture fuel cells. The transition to the hydrogen-powered system could take several decades due to the slow turnover of the existing stock of capital. The transition to a hydrogen economy is likely to begin later in most developing economies than in industrialized countries. Hydrogen is a synthetic energy carrier. The synthesis of hydrogen requires energy. Since production, packaging, storage, transfer and delivery of hydrogen gas, in essence all key components of an economy, are extremely energy consuming, alternatives should be considered. The production technology would be sitespecific and include steam reforming of methane and electrolysis in hydropowerrich countries. Conventionally produced hydrogen gas costs about twice that of natural gas or oil and about three times that of coal. At present only the space industry seems to be willing to pay the high cost of hydrogen energy. Hydrogen can be transported by two systems: (1) a road delivery system (cryogenic liquid trucks, compressed tube trailers), and (2) a pipeline delivery system. Placing the pipelines in sewers, securing utility status, or converting existing natural gas pipelines to carry a mixture of hydrogen and natural gas could reduce hydrogen pipeline costs. Hydrogen could be a peaceful energy carrier for all countries. Hydrogen might be the next great fuel, as it is available worldwide and water is its only byproduct. Hydrogen has received increased attention as a renewable and environmentally friendly option to help meet today’s energy needs. Policy makers will need to pay more attention to the implications for the transition to a hydrogen economy. A major dilemma now faced by developing countries is how to invest in hydrogen research and development for the transition to a hydrogen economy. Hydrogen’s share in the energy market is increasing with the implementation of fuel cell systems for sustainable energy supply. The concept of sustainable development embodies the idea of the interlinking and balance between economic, social and environmental concerns. Hydrogen is currently more expensive than conventional energy sources. There are different technologies presently being practiced to produce hydrogen economically from biomass. Biohydrogen technology will play a major role in the future since it is able to utilize renewable sources of energy. The use of biohydrogen for transport in order to reduce greenhouse gas emissions and the environmental impact of transport has a strategic importance. Since hydrogen can be burned in such a way that it produces no harmful emissions, this makes it an attractive alternative to fossil fuels. But hydrogen is only as clean as the technologies used to produce and use it. If hydrogen is produced without emitting any carbon dioxide or other climate-destabilizing greenhouse gases, it could form the basis of a truly sustainable energy system. Vehicles and stationary power generation fueled by hydrogen are zero-emission devices at the point of use, which benefits local air quality. Hydrogen-powered fuel

Preface

vii

cells could contribute to reducing or eliminating emissions of carbon dioxide and other greenhouse gases from road transportation vehicles. The production of hydrogen electrolytically, using clean solar power or other forms of renewable energy is essentially pollution-free. The feedstock, water, is composed of hydrogen and oxygen. Hydrogen production or distribution would produce no CO2. An internal combustion engine fueled by hydrogen can be adjusted so that the emission of NOx is 200 times less than in present vehicles. Emissions of NOx increase with the combustion temperature, the length of the high-temperature combustion period, and the availability of hydrogen, up to a point. This book on biohydrogen attempts to address the needs of energy researchers, chemical engineers, energy specialists, engineers, agriculturists, crop cultivators, fuel processors, policy makers, environmentalists, environmental engineers, automobile engineers, college students, research faculty and others interested in a practical tool for pursuing their interests in relation to bioenergy. Each chapter in the book begins with fundamental explanations for general readers and ends with indepth scientific details suitable for expert readers. The book may even be adopted as a textbook for college courses that deal with biohydrogen. Trabzon, Turkey, November 2008

Ayhan Demirbas

Contents

Chapter1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1 1.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   1 1.1.1 Global Energy Sources and the Present Energy Situation  . . . .   2 1.2 Conventional Fossil Fuel Sources   . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5 1.2.1 Petroleum and Heavy Oil Refining  . . . . . . . . . . . . . . . . . . . . .   6 1.2.2 Petroleum Products and Fuels  . . . . . . . . . . . . . . . . . . . . . . . . .   9 1.2.3 Coal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   10 1.3 Unconventional Fossil Fuel Sources   . . . . . . . . . . . . . . . . . . . . . . . . . .   14 1.3.1 Natural Gas  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   14 1.3.2 Oil Shale (Shale Oil)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   17 1.3.3 Tar Sand Bitumen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   18 1.4 Renewable Energy Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   18 1.4.1 Biomass  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   21 1.4.2 Hydropower  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   25 1.4.3 Geothermal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   27 1.4.4 Wind  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   28 1.4.5 Solar  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   30 1.4.6 Other Renewable Energy Sources  . . . . . . . . . . . . . . . . . . . . . .   33 1.5 Nuclear Fuel Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   36 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   39 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   39



Chapter2 Fuels from Biomass   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   43 2.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   43 2.2 Biomass Feedstocks  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   45 2.3 The Chemistry of Biomass  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   49 2.4 Production of Fuels from Wood Sources   . . . . . . . . . . . . . . . . . . . . . . .   52 2.5 Production of Fuels from Crops   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   52 2.5.1 Fuels from Cereal Crops   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   53 2.5.2 Fuels from Non-Cereal Crops  . . . . . . . . . . . . . . . . . . . . . . . . .   54 2.5.3 Fuels from Energy Crops   . . . . . . . . . . . . . . . . . . . . . . . . . . . .   57 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   58 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   58



ix

x

Contents

Chapter3 Biofuels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Bioethanol  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Other Bioalcohols  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Biorefinery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 Biodiesel  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Biogas  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7 Landfill Gas  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 Fischer–Tropsch Liquids from Biorenewable Feedstocks  . . . . . . . . . Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .



  61   61   64   65   67   71   74   78   79   82   83

Chapter4 Transportation Fuels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   85 4.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   85 4.2 Liquefied Petroleum Gas  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   89 4.3 Compressed Natural Gas  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   91 4.4 Hydrogen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   93 4.5 Electricity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94 4.6 Solar  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94 4.7 Biorenewable Liquid Fuels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   94 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   103 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   104



Chapter5 Hydrogen   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105 5.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   105 5.2 History  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   106 5.3 Properties of Hydrogen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   107 5.4 Fuel Properties of Hydrogen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   108 5.5 Hydrogen Production Processes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   110 5.5.1 Hydrogen from Natural Gas by Steam Reforming  . . . . . . . .   111 5.5.2 Hydrogen Production from Hydrocarbons  . . . . . . . . . . . . . .   111 5.5.3 Hydrogen from Coal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   113 5.5.4 Hydrogen from Water  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   115 5.5.5 Photocatalytic Hydrogen Production  . . . . . . . . . . . . . . . . . . .   119 5.5.6 Solar-Powered Hydrogen Generation  . . . . . . . . . . . . . . . . . .   129 5.5.7 Hydrogen from Hydrogen Sulfide  . . . . . . . . . . . . . . . . . . . . .   130 5.6 Storage of Hydrogen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   134 5.6.1 Hydrogen Storage with Metal Hydrides  . . . . . . . . . . . . . . . .   136 5.6.2 Hydrogen Absorption/Desorption with Oxygen-Contaminated Boron Film  . . . . . . . . . . . . . . . .   139 5.6.3 Hydrogen Storage with Carbon Structures  . . . . . . . . . . . . . .   140 5.7 Hydrogen Storage Materials  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   141 5.7.1 Boron Hydrides as Metal Hydrides  . . . . . . . . . . . . . . . . . . . .   142 5.7.2 Hydrogen in Mechanically Milled Amorphous Boron  . . . . .   143 5.7.3 Boron Complex Hydrides   . . . . . . . . . . . . . . . . . . . . . . . . . . .   143

Contents

xi

5.8

Hydrogen Fuel for Internal Combustion Engine  . . . . . . . . . . . . . . . . .   145 5.8.1 Advantages of Hydrogen as an Engine Fuel  . . . . . . . . . . . . .   146 5.8.2 Disadvantages of Hydrogen as an Engine Fuel  . . . . . . . . . . .   147 5.9 Liquefaction and Compression of Hydrogen   . . . . . . . . . . . . . . . . . . .   148 5.9.1 Nanocatalytic Liquefaction of Hydrogen  . . . . . . . . . . . . . . .   149 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   152 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   153



Chapter6 Biohydrogen   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   163 6.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   163 6.2 Definition  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   164 6.3 History  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   164 6.4 Hydrogen from Biorenewables via Biological Processes  . . . . . . . . . .   166 6.4.1 Hydrogen Production via Microbial Fermentation of Biomass  . . . . . . . . . . . . . . . . . . . . . . . . . . . .   170 6.4.2 Anaerobic Hydrogen Production  . . . . . . . . . . . . . . . . . . . . . .   170 6.4.3 Biophotolytic Hydrogen Production  . . . . . . . . . . . . . . . . . . .   172 6.4.4 Dark Fermentative Hydrogen Production  . . . . . . . . . . . . . . .   174 6.5 Hydrogen from Biorenewables via Thermochemical Processes   . . . .   176 6.5.1 Potential of Renewable Hydrogen Production  . . . . . . . . . . .   178 6.5.2 Production of Hydrogen from Biomass via Pyrolysis   . . . . .   179 6.5.3 Production of Hydrogen from Biomass via Gasification  . . .   186 6.5.4 Hydrogen from Biomass via Non-Conventional Processes  .   195 6.5.5 Hydrogen from Biomass Gasification by Steam Reforming   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   197 6.5.6 Hydrogen from Biomass via Air–Steam Gasification  . . . . . .   199 6.5.7 Hydrogen from Biomass by Supercritical Water Gasification   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   202 6.5.8 Hydrogen-rich Gas from Shells via Supercritical Water Extraction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   206 6.5.9 Production of Hydrogen from Mosses and Algae via Pyrolysis and Steam Gasification  . . . . . . . . . . . . . . . . . .   208 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   214 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   214



Chapter7 Fuel Cells   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   221 7.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   221 7.1.1 History of Fuel Cells  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   222 7.2 Fundamentals of a Fuel Cell  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   224 7.3 Different Types of Fuel Cells  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   226 7.3.1 Proton Exchange Membrane Fuel Cells (PEMFCs)  . . . . . . .   226 7.3.2 Direct Use of Methanol in Fuel Cells  . . . . . . . . . . . . . . . . . .   228 7.3.3 Characteristics of Main Types of Fuel Cells  . . . . . . . . . . . . .   230 7.4 Catalysts Used in Fuel Cells  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   231 7.5 Use of Alternative Fuel in Fuel Cells  . . . . . . . . . . . . . . . . . . . . . . . . .   233

xii

Contents

7.5.1 Biodiesel-Fueled Cells  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   233 7.6 Hybrid Electric Vehicles and Supercapacitors  . . . . . . . . . . . . . . . . . .   235 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   237 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   238



Chapter8 The Hydrogen Economy  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   241 8.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   241 8.2 Cost of Hydrogen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   243 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   249 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   250



Chapter9 Hydrogen Policy   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   253 9.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   253 9.2 Political, Environmental, and Economical Impacts of Hydrogen  . . . .   254 9.3 Global Biofuel Projections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   257 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   260 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   260



Chapter10 Environmental Impacts of Hydrogen   . . . . . . . . . . . . . . . . . . . . . . . . . . . .   263 10.1 Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   263 10.2 Environmental Impacts of Hydrogen   . . . . . . . . . . . . . . . . . . . . . . . . .   265 Summary   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   268 References   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   269



SubjectIndex  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   271

Chapter 1

Introduction

1.1 Introduction At the start of the twenty-first century, we are facing significant energy challenges. The world’s energy requirements are currently satisfied by fossil fuels, which serve as the primary energy source. Consequently, overwhelming scientific evidence concludes that this unfettered use of fossil fuels has caused the world’s climate to change, with potentially disastrous effect. Moreover, oil crises, which surfaced in 1973, provided a reminder that breaking an energy paradigm based on fossil fuel dependency would lead to economic and environmental advantages. In response, a sustained program of research and development into many areas of hydrogen as an energy carrier started in 1977, with the initiation of the International Energy Agency (Vijayaraghavan and Soom, 2006). Hydrogen is seen as the energy carrier of the future. Hydrogen is storable and transferable, has high heat value per mass unit, and its sources are globally distributed. Hydrogen is strategically important as it has low emission, is environmentally benign, and represents a cleaner and more sustainable energy system. Hydrogen seems to be the future energy carrier by virtue of being renewable. All primary energy sources can be used in the hydrogen-producing process (Veziroglu, 1975). Hydrogen produced from renewable resources such as water, organic waste or biomass, either biologically or photobiologically, is termed as “biohydrogen.” Biohydrogen can be generated from renewable sources, namely biomass, and more particularly by the photobiological method and dark fermentation process. Biohydrogen production has several advantages when compared to photoelectrochemical or thermochemical processes due to the low energy requirement and investment cost. Most of the biologically produced hydrogen in the biosphere is derived from microbial fermentation processes. These organisms decompose organic matter into carbon dioxide and hydrogen (Gorman, 2002). Hydrogen production from fossil fuels is based on steam reforming of natural gas, thermal cracking of natural gas, partial oxidation of heavier than naphtha A. Demirbas, Biohydrogen, © Springer 2009

1

2

1  Introduction

hydrocarbons, coal gasification and pyrolysis or gasification. Among these methods, the steam reforming process alone produces nearly 90% of hydrogen. The biological methods of hydrogen production are based on biophotolysis of water by algae and cyanobacteria, photodecomposition of organic compounds by photosynthetic bacteria, fermentative hydrogen production from organic compounds and hybrid systems using photosynthetic and fermentative bacteria. Hydrogen production from water is based on electrolysis, photolysis, thermochemical process and direct thermal decomposition or thermolysis (Das and Veziroglu, 2001).

1.1.1 Global Energy Sources and the Present Energy Situation Energy affects all aspects of modern life. Energy plays a vital role in our everyday lives. Energy is one of the vital inputs to the socioeconomic development of any country. The demand for energy is increasing at an exponential rate due to the exponential growth of world population. An energy system includes an energy supply sector and energy end-use technologies. The objective of an energy system is to deliver to consumers the benefits that energy use offers, including illumination, cooked food, comfortable indoor temperatures, refrigeration, telecommunications, education, and transportation. Energy end-use equipment such as stoves, light bulbs, vehicles, and machinery convert the final energy into useful energy, which provides the desired benefits: the energy services (UNDP, 2004). Heat, electricity, and vehicle fuel are the main forms of energy that people use every day. Advanced energy-efficient technologies reduce the energy needed to provide energy services, thereby reducing environmental and national security costs of using energy and potentially increasing its reliability. Energy resources are not used for their own sake, but for the services they provide. These energy services are fundamental to our modern economy; they heat, cool, and light our buildings, power our industrial processes, process our food, fuel our transport, and energize our communications and information technologies. Energy sources are classified into three groups: fossil, fissile and renewable. The term fossil refers to an earlier geologic age. Fossil fuels were formed a great many years ago and are not renewable. The fossil energy sources are petroleum, coal, bitumens, natural gas, oil shales, and tar sands. The main fissile energy sources are uranium and thorium. Figure 1.1 shows fossil, nuclear and renewable energy consumptions of the world in 2005. Oil is the largest single source of energy consumed by the world’s population. Unfortunately petroleum oil is in danger of becoming short in supply. Hence, the future trend is towards using alternate energy sources. Fortunately, technological development is making this transition possible. Figure 1.2 shows global oil production scenarios based on today’s production. A peak in global oil production may occur between 2015 and 2030. Roughly 80% of the world’s energy comes from fossil fuels, where oil is the world’s leading energy resource. The oil resources are concentrated in a few regions.

1.1  Introduction

3

50

Percent of total energy

40

30

20

10

0

Oil

Coal

Natural gas

Nuclear

Renewables

Fig. 1.1  Global energy consumption in 2005

Fig. 1.2  Global oil production scenarios based on today’s production. Adapted from Demirbas (2008)

Percent of today’s production

Countries in the Middle East and Russia hold 70% of the world’s dwindling reserves of oil and gas. Coal is the most abundant and widely distributed fossil fuel. Global natural gas reserves are large and currently yield a reserve/production ratio of 50 to 60 years. Nuclear power’s share of worldwide electricity supplies has been steady at 16–17% for many years, but reactor safety and waste disposal problems are still matters of concern. The renewable energy sources such as biomass, hydropower, wind, solar (thermal and photovoltaic), geothermal, marine, and hydrogen will play an important role in the world’s future. Approximately, half of the global energy supply will be derived from renewables in 2040. It is also projected that electricity generation from renewables will contribute more than 80% to the total global electricity supply by the year 2040 (EWEA, 2005; EREC, 2006).

110 95 80 65 50 35 2000

2015

2030 2045 Year

2060

2075

4

1  Introduction

Table 1.1  Global primary energy consumption, by energy source for 2002 (shares in 10.2 Gtoe) Energy source

Percentage of total

Oil

35.1

Coal

22.6

Natural gas

21.7

Nuclear

6.9

Traditional biomass

9.3

Hydropower

2.3

Modern biomass

1.4

Geothermal, solar, wind, etc.

0.8

Renewable energy sources such as wind, solar, biomass and hydropower are important today, and they will be important in the future. Table 1.1 shows the global primary energy consumption as shares of 10.2 gigatons of oil equivalent (Gtoe) by energy source in 2002 (UNDP, 2004). Table  1.2 shows the global electricity production as shares of 15.48 terawatt hour (TWh), per energy source for the year 2002. Hydropower is the largest and most important renewable resource and generates about 17% of the world’s electricity. Non-hydro renewables are expected to make a growing contribution to global power generation. Biomass has the potential to become the world’s largest and most sustainable renewable energy source. However, to move forward from this potential stage, both production and end-use technologies must be modernized. Wind is often considered to be the most advanced of the renewables, after hydropower. Geothermal is an important renewable resource and it can be utilized for base-load electricity production. The best geothermal fields are located within well-defined belts of geologic activity. Solar radiation, the earth’s primary source of energy, is being increasingly utilized, while photovoltaic (PV) power generation is still the most expensive solar technology (WEC, 2004). Other energy resources are peat, oil shale, tar sand, landfill, wave, tidal, OTEC (ocean thermal energy conversion), natural bitumen and extra-heavy oil and wood. Considering observations from the last 30 years, oil has been losing share, gas has been growing, coal has been coming down, while nuclear and hydropower are both constant at about 6%. Renewables still make a minor contribution to world’s energy market. The present world energy supply system is facing three basic problems: (1) limitation of fossil fuel resources, (2) climate change by carbon dioxide emission, and (3) insecurity by nuclear weapon competence and radioactive materials. The strategic goal therefore should be to transition to unlimited resources, use zero-emission fuels and accept no options for abuse. About 98% of carbon emissions result from fossil fuel combustion. Reducing the use of fossil fuels would considerably reduce the amount of carbon dioxide

1.2  Conventional Fossil Fuel Sources

5

Table 1.2  World electricity production per energy source for 2002 (shares of 15.476 TWh). Adapted from UNDP (2004) Energy source

Percentage of total

Coal

38.3

Natural gas

18.1

Nuclear

17.0

Hydropower

16.5

Petroleum products

7.5

Combustible renewables and waste

1.1

Small hydropower

1.0

Geothermal, solar, wind, etc.

0.6

and other pollutants produced. This can be achieved by either using less energy altogether or by replacing fossil fuels by renewable fuels. Therefore, current efforts focus on advancing technologies that emit less carbon (e.g., high-efficiency combustion) or no carbon at all, such as nuclear, hydrogen, solar, wind, geothermal, or on using energy more efficiently and on developing sequestration of carbon dioxide emitted during fossil fuel combustion. Another problem with petroleum fuels is their uneven distribution in the world; for example, the Middle East has 63% of the global reserves and is the dominant supplier of petroleum. This energy system is unsustainable because of equity issues as well as environmental, economic, and geopolitical concerns that have far-reaching implications. Interestingly, renewable energy resources are more evenly distributed than fossil or nuclear resources. Also, the energy flows from renewable resources are more than three orders of magnitude higher than current global energy needs. Thus, sustainable renewable energy sources such as biomass, hydropower, wind, solar (both thermal and photovoltaic), geothermal, and marine will play an important role in the world’s future energy supply.

1.2 Conventional Fossil Fuel Sources Conventional fuel sources are petroleum and coal (including lignite). Our modern way of life is intimately dependent upon fossil fuels or mineral fuels. Conventional energy sources based on petroleum and coal have proven to be highly effective drivers of economic progress, but at the same time damaging to the environment and to human health (Akella et al., 2009). One of our most important sources of energy today is oil and coal. Fossil fuels are found deposited in rock formations. Fossils are non-renewable and relatively rare resources. More importantly, the major energy demand is fulfilled by fossil fuels. Fossil fuels are fossil source fuels, that is, hydrocarbons found within the top

6

1  Introduction

layer of the Earth’s crust. It is generally accepted that they formed from the fossilized remains of dead plants and animals by exposure to heat and pressure in the Earth’s crust over hundreds of millions of years.

1.2.1 Petroleum and Heavy Oil Refining Petroleum (word derived from the Greek petra meaning rock, and elaion meaning oil, or Latin oleum meaning oil) or crude oil, sometimes colloquially called “black gold,” is a thick, dark brown or greenish liquid. It is used to describe a broad range of hydrocarbons that are found as gases, liquids, or solids, occurring in nature. Petroleum consists of a complex mixture of various hydrocarbons, largely of the alkane and aromatic compounds, but may vary much in appearance and composition. The physical properties of petroleum vary greatly. The color ranges from pale yellow through red and brown to black or greenish. The two most common forms are crude oil and natural gas. Petroleum is a fossil fuel because it was formed from the remains of tiny sea plants and animals that died millions of years ago, and sank to the bottom of the oceans. This organic mixture was subjected to enormous hydraulic pressure and geothermal heat. Over time, the mixture changed, breaking down into compounds made of hydrocarbons by reduction reactions, resulting in the formation of oil-saturated rocks. The oil rose and became trapped under nonporous rocks, which are sealed with salt or clay layers. According to the well-accepted biogenic theory, crude oil, like coal and natural gas, is the product of compression and heating of ancient vegetation and animal remains over geological time scales. According to this theory, organic matter is formed from the decayed remains of prehistoric marine animals and terrestrial plants. Over many centuries this organic matter, mixed with mud, was buried under thick sedimentary layers. The resulting high pressure and heat caused the remains to transform, first into a waxy material known as kerogen, and then into liquid and gaseous hydrocarbons by the catagenesis process. The fluids then migrated through adjacent rock layers until they became trapped underground in porous rocks known as reservoirs, forming an oil field, from which the liquid could then be removed by drilling and pumping. These reservoirs are at different depths in different parts of the world, but typically lie between 4 and 5 km underground. The thickness of the oil layer is about 150 m, known generally as the “oil window.” Three important elements of an oil reservoir are: a rich source rock, a migration conduit, and a trap (seal) that forms the reservoir. The first oil wells were drilled in China in the fourth century, or perhaps earlier. The wells, as deep as 243 m, were drilled using bits attached to bamboo poles. The oil was burned to produce heat needed in the production of salt from brine evaporation. By the tenth century, extensive bamboo pipelines connected oil wells with salt springs. Ancient Persian tablets also indicate the medicinal and lighting uses of petroleum in the upper echelons of their society. In the eighth century, the streets of the newly constructed Baghdad were paved with tar, derived from easily accessible petroleum from natural fields in the region.

1.2  Conventional Fossil Fuel Sources

7

In the ninth century, oil fields were exploited to produce naphtha in Baku, Azerbaijan. These fields, described by the geographer Masudi in the tenth century, had increased output to hundreds of shiploads in the thirteenth century as described by Marco Polo.  The modern history of petroleum began in 1846, with the discovery of refining kerosene from coal by Atlantic Canada’s Abraham Pineo Gesner. Poland’s Ignacy Łukasiewicz discovered a means of refining kerosene from the more readily available “rock oil” (petr-oleum) in 1852, and in the following year the first rock oil mine was built in Bobrka, near Krosno in southern Poland. The discovery rapidly spread around the world, and Meerzoeff built the first Russian refinery in the more established oil fields at Baku in 1861, which produced about 90% of the world’s oil. In fact, the battle of Stalingrad was fought over Baku (now the capital of the Azerbaijan Republic). James Miller Williams drilled the first commercial oil well in North America in 1858 in Oil Springs, Ontario, Canada. In the following year, Edwin Drake discovered oil near Titusville, Pennsylvania. There he pioneered a new method for producing oil from the ground, in which he drilled using piping to prevent borehole collapse, allowing for the drill to penetrate deeper into the ground. Previous methods for collecting oil had been limited. For example, ground collection of oil consisted of gathering it from where it occurred naturally, such as from oil seeps or shallow holes dug into the ground. The methods of digging large shafts into the ground also failed, as collapse from water seepage almost always occurred. The significant advancement that Drake made was to drive a 10-m iron pipe through the ground into the bedrock below. This allowed Drake to drill inside the pipe, without the hole collapsing from the water seepage. The principle behind this idea is still employed today by many companies for petroleum drilling. Drake’s well was 23 m deep, which is very shallow compared to today’s well depth of 1000–4000 m. Although technology has improved the odds since the time of Edwin Drake, petroleum exploration today is still a gamble. For example, only about 33 in every 100 exploratory wells have oil, and the remaining 67 come up “dry.” For about 10 years Pennsylvania was the one great oil producer of the world, however since 1870, the industry has spread all over the globe. From the time of the completion on the Baku field of the first flowing well, Russia has ranked second in the list of oil-producing countries, while the region of Galicia in Central Europe and Romania became prominent in 1878 and 1880, respectively. In time, Sumatra, Java, Burma and Borneo, where active development began in 1883, 1886, 1890 and 1896, respectively, will perhaps rank among the chief sources of oil supplies of the world. The Middle East produces 32% of the world’s oil (Table 1.3), but more importantly it has 64% of the total proven oil reserves in the world (Table  1.4). Also, Table 1.3  Percentage of petroleum production by region Middle East 32

Latin America 14

Eastern Europe 13

North America 11

Asia and Pacific 11

Africa 10

Western Europe 9

8

1  Introduction

Table 1.4  Percentage of total proven reserves by region Middle East 64

Latin America 12

Eastern Europe 6

North America

Asia and Pacific

3

4

Africa

Western Europe

9

2

its reserves are depleting at a slower rate than any other region in the world. The Middle East provides more than half of OPEC’s total oil exports and has a major influence on the worldwide crude oil prices, despite the fact that OPEC produces less than half the oil in the world. Crude oil is a complex mixture that is between 50 and 95% hydrocarbon by weight. Table 1.5 shows the average elemental composition of crude oil. The oil industry classifies “crude” by its production location (e.g., “West Texas Intermediate, WTI” or “Brent”), relative density (API gravity), viscosity (“light,” “intermediate,” or “heavy”), and sulfur content (“sweet” for low sulfur, and “sour” for high sulfur). Additional classification is due to conventional and non-conventional oil as shown in Table 1.6. The petroleum industry can be divided into two subgroups, upstream producers (exploration, development and production of crude oil or natural gas) and downstream transporters (tanker, pipeline transport), and also includes refiners, retailers, and consumers.

Table 1.5  Average elemental composition of crude oil Element

Percent composition

Carbon

83.0–87.0

Hydrogen

10.0–14.0

Nitrogen

0.1–2.0

Sulfur

0.05–6.0

Oxygen

0.05–1.5

Table 1.6  Classification of crude oils Class Light crude Medium oil Heavy oil Deep sea oil above 500 m water depth Extra heavy oil below (including tar sands)

Viscosity of oil (measured in °API) > 31.1 22.3–31.1 < 22.3 – < 10

Oil shale

–

Bitumen from tar sands

–

1.2  Conventional Fossil Fuel Sources

9

Table 1.7  Main crude oil fractions Fraction Natural gas

Boiling range (K) < 293

Number of carbon atoms C1 to C4

Petroleum ether

293–333

C5 to C6

Ligroin (light naphtha)

333–373

C6 to C7

Gasoline

313–478

C5 to C12, and cycloalkanes

Jet fuel

378–538

C8 to C14, and aromatics

Kerosene

423–588

C10 to C16, and aromatics

No. 1 diesel fuel

443–595

C9 to C18, and aromatics

No. 2 diesel fuel

448–638

C12 to C24, and aromatics

No. 3 diesel fuel

458–663

C10 to C20, and aromatics

Gas oil (No. 4 and 5 fuel oils)

> 548

C12 to C70, and aromatics

Gas oil (No. 6 fuel oils)

> 548

C12 to C70, and aromatics

Lubricating oils

> 673

Asphalt or petroleum coke

Non-volatile esidue

> C20 Polycyclic structures

The first step in refining crude oil involves separating the oil into different hydrocarbon fractions by distillation. Main fractions of crude oil are given in Table 1.7. Since there are a number of factors that influence the boiling point of a hydrocarbon, these petroleum fractions are complex mixtures. An oil refinery cleans and separates the crude oil into various fuels and byproducts, including gasoline, diesel fuel, heating oil, and jet fuel. Since various components boil at different temperatures, refineries use a heating process called distillation to separate the components. For example, gasoline has a lower boiling point than kerosene, allowing the two to be separated by heating to different temperatures. Another important job of the refineries is to remove contaminants from the oil, for example, sulfur from gasoline or diesel to reduce air pollution from automobile exhausts. After processing at the refinery, gasoline and other liquid products are usually shipped out through pipelines, which are the safest and cheapest way to move large quantities of petroleum across land.

1.2.2 Petroleum Products and Fuels An important non-fuel use of petroleum is to produce chemical raw materials. The two main classes of petrochemical raw materials are olefins (including ethylene and propylene) and aromatics (including benzene and xylene isomers), both of which are produced in large quantities. A very important aspect of petrochemicals is their extremely large scale. The olefins are produced by chemical cracking by using steam or catalysts, and the aromatics are produced by catalytic reforming. These

10

1  Introduction

two basic building blocks serve as feedstock to produce a wide range of chemicals and materials including monomers, solvents, and adhesives. From the monomers, polymers or oligomers are produced for use as plastics, resins, fibers, elastomers, certain lubricants, and gels. Gasoline is a blend of hydrocarbons with some contaminants, including sulfur, nitrogen, oxygen, and certain metals. The four major constituent groups of gasoline are olefins, aromatics, paraffins, and naphthenes. The important characteristics of gasoline are density, vapor pressure, distillation range, octane, and chemical composition. Diesel fuel is produced by distilling raw oil, which is extracted from bedrock. Diesel fuel is a fossil fuel. Diesel fuel consists of hydrocarbons with between 9 and 27 carbon atoms in a chain as well as a smaller amount of sulfur, nitrogen, oxygen and metal compounds. It is a general property of hydrocarbons that the autoignition temperature is higher for more volatile hydrocarbons. The hydrocarbons present in the diesel fuels include alkanes, naphthenes, olefins and aromatics. In addition other substances are added to improve the characteristics of diesel fuel. Its boiling point is between 445 and 640 K. A good diesel fuel is characterized by low sulfur and aromatic content, good ignition quality, the right cold weather properties, low content of pollutants and also the right density, viscosity and boiling point. No. 2 diesel fuel is commonly used in diesel engines. Its boiling point is between 458 and 663 K and it includes C12–C24 hydrocarbons and aromatics compounds.

1.2.3 Coal The first known and the oldest fossil fuel is coal. Among all fossil energy resources, the coal reserve of the world is the largest. Coal is basically carbon, left over from bacterial action upon decaying plant matter in the absence of oxygen, usually under silt and water. The first step in coal formation yields peat, compressed plant matter, which still contains twigs and leaves. The second step is the formation of brown coal or lignite. Lignite has already lost most of the original moisture, oxygen, and nitrogen. It is widely used as a heating fuel but is of little chemical interest. In the third stage, the lignite is successively changed to subbituminous, bituminous, and anthracite coal. Not all of the deposits were subjected to the same degree of conversion. The bituminous coal is the most abundant form of coal and is the source of coke for smelting, coal tar, and many forms of chemically modified fuels. The chemical properties of typical coal samples are given in Table 1.8. Depending on the geological age, the organic material will transform into the following members of the coal family: 1. Lignite. This contains considerable amount of water and volatiles and some mineral matters. It is youngest in geological age. 2. Bituminous. Moderate amount of moisture, volatiles, and inorganic materials are in bituminous coal. 3. Anthracite. This contains very little water or moisture but a large amount of carbon. It is the oldest in geological age.

1.2  Conventional Fossil Fuel Sources

11

Table 1.8  Chemical properties of typical coal samples Low-rank coal Carbon, % Hydrogen, %

75.2

High-volatile coal 82.5

High-rank coal 90.5

6.0

5.5

4.5

Oxygen, %

17.0

9.6

2.6

Nitrogen, %

1.2

1.7

1.9

0.6

0.7

0.5

Moisture, %

Sulfur, %

10.8

7.8

6.5

Calorific value, MJ/kg

31.4

35.0

36.0

The worldwide coal production is roughly equal to the gas production and only second to that of oil. Coal is produced in deep mines (hard coal) and in surface mines (lignite). Coal has played a key role as a primary source of organic chemicals as well as a primary energy source. Coal may become more important both as an energy source and as the source of carbon-based materials, especially aromatic chemicals in the twenty-first century (Schobert and Song, 2002). Coal accounted for 26% of the world’s primary energy consumption and 37% of the energy consumed worldwide for electricity generation (Demirbas, 2006a). The worldwide coal production and consumption in 1998 were 5043 and 5014 million short tons, respectively. The known world recoverable coal reserves in 1999 were 1087 billion short tons (AER, 1999; IEA, 2000). Coal reserves are rather evenly spread around the globe: 25% are in the USA, 16% in Russia, and 11.5% in China. Although coal is much more abundant than oil and gas on a global scale, coalfields can be depleted in a region. The known world recoverable coal reserves in 1999 were 989 billion tons. The coal mining industry has exacted a heavy price from past generations. Despite environmental issues and competitive pressure from other fuels, coal is expected to maintain a major share of the world’s future energy use. Large increases in coal use are projected for the developing countries of Asia. Coal’s role in energy use worldwide has shifted substantially over the decades, from a fuel used extensively in all sectors of the economy to one that is now used primarily for electricity generation and in a few key industrial sectors, such as steel, cement, and chemicals. Although coal has lost market share to petroleum products and natural gas, it continues to be a key source of energy because of the dominant role it has maintained in its core markets and its success in penetrating markets in emerging economies. For coal to remain competitive with other sources of energy in the industrialized countries of the world, continuing technological improvements in all aspects of coal extraction are necessary. Nearly all the different forms of coal are used in some way or other. For instance, peat has been used for burning in furnaces, lignite is used in power station and home stoves, whereas bituminous coal is used extensively for the generation of electricity. Coke is used primarily in the steel industry, where high temperatures are required.

12

1  Introduction

More than 45% of the world’s electricity is generated from coal and it is the major fuel for generating electricity worldwide. The known coal reserves in the world are enough for consumption for over 215 years, while the known oil reserves are only about 39 times the world’s consumption and the known natural gas reserves are about 63 times the world’s consumption level in 1998. Coal is not only plentiful, but also economical. Advanced coal-fired power generation technologies should be developed worldwide to generate at minimum economic coal, improve thermal efficiency and meet environmental requirements. Sustainability goals indicate the importance of evolving fossil energy technologies towards the long-term goal of near-zero air pollutant and greenhouse gas emissions, without complicated end-of-pipe control technologies. Near-term technologies and strategies should support this long-term goal. The technological revolution under way in power generation, where advanced systems are replacing steam turbine technologies, supports this long-term goal. Coal, as the most abundant and widely distributed fossil fuel, can be mined with modern techniques, transported and stored efficiently and cost-effectively. International coal trade is growing steadily and there is vigorous competition on supply and price. But coal’s future commercial development depends critically on its environmental acceptability and in particular on the success of the power generation industry in reducing sulfurous and other polluting emissions.  The use of low-sulfur coals and the introduction of more efficient flue gas desulfurization facilities in conventional power stations have contributed to a significant lowering of emissions, but further improvement by these means is limited. Coal may become more imported both as an energy source and as the source of organic chemicals in this century (Demirbas and Güllü, 1998). Coal science is an applied discipline, using methods of science and engineering for research into genesis, characterization, conversion and utilization of coal and related solid fuels (Demirbas, 1999). Energy production from fossil fuels, including coal, results in high greenhouse gas emissions. Global utilization of fossil fuels for energy needs is rapidly resulting in critical environmental problems throughout the world. We now know that petroleum’s success created problems with global warming, energy security, and environmental conservation. Coal has been utilized as a primary source of energy, as well as a primary source of organic chemicals. It is a complex, heterogeneous combustible material, made up of portions that are either useful (carbon and hydrogen), or useless (diluents such as moisture, ash and oxygen, or contaminants such as sulfur and heavy metals). Coal can be defined as a sedimentary rock that burns, and as it was formed by the decomposition of plant matter, can be found in many forms. There are four classes of coal: anthracite, bituminous, subbituminous, and lignite. Elemental analysis gives empirical formulas such as C137H97O9NS for bituminous coal and C240H90O4NS for high-grade anthracite. As early as 1800, coal gas or town gas was made by heating coal in the absence of air. Coal gas is rich in CH4 and gives off up to 20.5 kJ per liter of gas burned. Coal gas became so popular that most major cities and many small towns had a local gas

1.2  Conventional Fossil Fuel Sources

13

house in which it was generated, and gas burners were adjusted to burn a fuel. Coal can be converted into water gas with steam by the following (Demirbas, 2007): C + H2O → CO + H2

(1.1)

Water gas burns to give CO2 and H2O, releasing roughly 11.2 kJ per liter of gas consumed. Water gas, formed by the reaction of coal with oxygen and steam, is a mixture of CO, CO2, and H2. The ratio of H2 to CO can be increased by adding water to this mixture, taking advantage of a reaction known as the water–gas shift reaction (Demirbas, 2007): CO + H2O → CO2 + H2

(1.2)

The concentration of CO2 can be decreased by the reaction of CO2 with coal at high temperatures to form CO: C + CO2 → 2CO

(1.3)

Water gas from which the CO2 has been removed is called synthesis gas because it can be used as a starting material for a variety of organic and inorganic compounds. For example, it can be used as the source of H2 for the synthesis of methanol: CO + 2H2 → CH3OH

(1.4)

Methanol can then be used as a starting material for the synthesis of alkenes, aromatic compounds, acetic acid, formaldehyde, and ethyl alcohol (ethanol). Synthesis gas can also be used to produce methane, or synthetic natural gas (SNG) (Demirbas, 2007): CO + 3H2

→ CH4 + H2O

(1.5)

2CO + 2H2

→ CH4 + CO2

(1.6)

The first step toward making liquid fuels from coal involves the manufacture of synthesis gas (CO and H2) from coal. In 1925, Franz Fischer and Hans Tropsch developed a catalyst that converted CO and H2 at 1 atm and 250 to 300°C into liquid hydrocarbons. By 1941, Fischer–Tropsch plants produced 740 000 tons of petroleum products per year in Germany (Dry, 1999). Fischer–Tropsch technology is based on a complex series of reactions that use H2 to reduce CO to CH2 groups linked to form long-chain hydrocarbons (Schulz, 1999): nCO + (n + m/2) H2 → CnHm + nH2O

(1.7)

At the end of World War II, Fischer–Tropsch technology was under study in most industrial nations. Coal can be gasified to produce synthesis gas (syngas), which can be converted to paraffinic liquid fuels and chemicals by the Fischer– Tropsch synthesis. Liquid product mainly contains benzene, toluene, xylene (BTX), phenols, alkylphenols and cresol. The low cost and high availability of crude oil, however, led to a decline in interest in liquid fuels made from coal.

14

1  Introduction

Another approach to liquid fuels is based on the reaction between CO and H2 to form methanol, CH3OH: CO + 2H2 → CH3OH

(1.8)

Methanol can be used directly as a transportation fuel, or it can be converted into gasoline with catalysts such as the ZSM-5 zeolite catalyst. Methanol can also be produced from syngas with hydrogen and carbon monoxide in a 2:1 ratio. Coal-derived methanol typically has low sulfur and other impurities. Syngas from coal can be reformed by reacting with water to produce hydrogen. Ammonium sulfate from coal tar by pyrolysis can be converted to ammonia. The humus substances can be recovered from brown coal by alkali extraction.

1.3 Unconventional Fossil Fuel Sources 1.3.1 Natural Gas Natural gas (NG) was known in England as early as 1659, but did not replace coal gas as an important source of energy in the world until after World War II. Usefulness of NG has been known for hundreds of years. The Chinese discovered a very long time ago that the energy in natural gas could be harnessed, and used to heat water. In the early days of the natural gas industry, the gas was mainly used to light streetlamps, and the occasional house. NG is expected to be the fastest growing component of global primary energy consumption. Consumption of NG is projected to increase by an average of 2.8% annually from 2001 to 2025, compared with projected annual growth rates of 1.8% for oil consumption and 1.5% for coal (Demirbas, 2006b). NG is found to consist mainly of the lightweight alkanes, with varying quantities of carbon dioxide, carbon monoxide, hydrogen, nitrogen and oxygen, in some cases also hydrogen sulfide and possibly ammonia. A typical sample of NG when it is collected at its source contains 80% methane (CH4), 7% ethane (C2H6), 6% propane (C3H8), 4% butane and isobutane (C4H10), and 3% pentane (C5H12). The reserves and resources of conventional NG are comparable in size to those of conventional oil, but global gas consumption is still considerably lower than that of oil. NG is found around the world, but the largest reserves are in the former Soviet Union and the Middle East. The proved gas reserves are unevenly distributed around the globe: 41% are in the Middle East and 27% in Russia. Global natural gas reserves by country are shown in Table 1.9. Around the world, NG use is increasing for a variety of reasons including prices, environmental concerns, fuel diversification and/or energy security issues, market deregulation, and overall economic growth. Figure 1.3 shows production and consumption trends of natural gas in the last decades. In NG consumption, the United States ranks first, the former USSR region ranks second, and Europe ranks third. The largest NG producer is Russia, which is also the largest supplier of NG to

1.3  Unconventional Fossil Fuel Sources

15

Western Europe. Asia and Oceania import NG to satisfy their demands. The other regions are relatively minor producers and consumers of natural gas. NG is one of the most widely used forms of energy today. It is commonly used to heat and cool homes and businesses. NG is a very versatile fuel, which can be used for space and water heating, which have traditionally been the predominant uses of natural gas, representing about 75% and 15% of natural gas use, respectively. Furnaces which burn NG to provide space heating and hot water for homes and businesses are the largest users of NG. Ultrahigh-efficiency gas furnaces can convert over 90% of the potential energy in NG into useful heat. The generation of electricity is the other main use of natural gas. NG can be used to generate electricity in many different ways. NG power plants generate more than a couple of hundred megawatts and use the same technology as coal-fired power plants. NG is burned to produce heat, which boils water, creating steam which passes through a turbine to generate electricity. Natural gas vehicles (NGVs) offer many benefits, from improving public health and the environment to aiding the transition to fuel cell vehicles. The following describes how NGVs are leading the way to a better tomorrow. Compared with vehicles fueled by conventional diesel and gasoline, NGVs can produce significantly lower amounts of harmful emissions such as nitrogen oxides, particulate matter, and toxic and carcinogenic pollutants. NGVs can also reduce emissions of carbon dioxide, the primary greenhouse gas. Fuel cell vehicles powered by hydrogen are the future of transportation. NG vehicle and infrastructure development can Table 1.9  World natural gas reserves by country. Adapted from Demirbas (2008) Country

Reserves (trillion cubic meter)

Percentage of world total

Russian Federation

48.1

33.0

Iran

23.0

15.8

Qatar

8.5

5.8

United Arab Emirates

6.0

4.1

Saudi Arabia

5.8

4.0

United States

4.7

3.3

Venezuela

4.0

2.8

Algeria

3.7

2.5

Nigeria

3.5

2.4

Iraq

3.1

2.1

Turkmenistan

2.9

2.0

Malaysia

2.3

1.6

Indonesia

2.0

1.4

Uzbekistan

1.9

1.3

Kazakhstan Rest of World

1.8

1.3

23.8

16.5

16

1  Introduction 2200 Natural gas production Natural gas consumption

Volume of natural gas, billion scf

2000 1800 1600 1400 1200 1000

1990

1992

1994

1996 Year

1998

2000

2002

Fig. 1.3  Production and consumption trends of natural gas in the world

facilitate the transition to this technology. Despite the large difference in volumetric energy density between gasoline and compressed natural gas (CNG), the impact of CNG energy density on engine performance is less dramatic. To use CNG safely, technicians and drivers need to know what the differences are and how to work with them. In general, the use of NG results in cleaner and longer-lasting engines. Less carbon builds up on spark plugs, engine oil, and in the combustion chamber. Natural gas has higher ignition temperatures than gasoline, which increases the importance of maintaining proper ignition system operation. Natural gas-fired combined cycles offering low costs, high efficiency, and low environmental impacts are being chosen wherever natural gas is readily available— in some countries even displacing large new hydropower projects. Co-generation is more cost-effective and can play a much larger role in the energy economy—if based on gas turbines and combined cycles rather than on steam turbines. 1.3.1.1 Gas Hydrates Natural gas (methane) can be obtained from gas hydrates. Gas hydrates are also called clathrates or methane hydrates. Gas hydrates are potentially one of the most important energy resources for the future. Methane gas hydrates are increasingly considered a potential energy resource. Methane gas hydrates are crystalline solids formed by combination of methane and water at low temperatures and high pressures. Gas hydrates have an ice-like crystalline lattice of water molecules with methane molecules trapped inside. Enormous reserves of hydrates can be found under continental shelves and on land under permafrost. The amount of organic

1.3  Unconventional Fossil Fuel Sources

17

Table 1.10  Worldwide amounts of organic carbon sources. Adapted from Hacisalihoglu et al. (2008) Source of organic carbon Gas hydrates (onshore and offshore)

Amount (gigaton) 10 000–11 000

Recoverable and non-recoverable fossil fuels (oil, coal, gas)

5000

Soil

1400

Dissolved organic matter

980

Land biota

880

Peat

500

Others

70

carbon in gas hydrates is estimated to be twice that in all other fossil fuels combined. However, due to the solid form of the gas hydrates, conventional gas and oil recovery techniques are not suitable. Table 1.10 shows worldwide amounts of organic carbon sources. The recovery of methane generally involves dissociating or melting in situ gas hydrates by heating the reservoir above the temperature of hydrate formation, or decreasing the reservoir pressure below hydrate equilibrium (Lee and Holder, 2001). Models have been developed to evaluate natural gas production from hydrates by both depressurization and heating methods. There are three methods to obtain methane from gas hydrates: (1) the depressurization method, (2) the thermal stimulation method, and (3) the chemical inhibition method. The thermal stimulation method and the chemical inhibitor injection method are both costly procedures, whereas the depressurization method may prove useful when applied to more than one production.

1.3.2 Oil Shale (Shale Oil) Oil shale is a sedimentary rock that contains solid hydrocarbon wax kerogen in tightly packed limy mud and clay. The kerogen may be decomposed at elevated temperatures (723 K), resulting in an oil suitable for refinery processing (Dorf, 1977). The oil shale layer was not hot enough to complete the oil generation. For the final step the kerogen must be heated up to 775 K and molecularly combine with additional hydrogen to complete the oil formation. This final process must be performed in the refinery and needs huge amounts of energy which otherwise were provided by the geological environment during oil formation. The kerogen is still in the source rock and could not accumulate in oil fields. Typically, the ratio of kerogen to waste material is very low, making the mining of oil shales unattractive. Hence, due to a combination of environmental and economic concerns, it is very unlikely that oil shale mining will ever be performed on a large scale, though in

18

1  Introduction

some places it is has been utilized in small quantities. Interestingly, the shale oil reserves in the world are greater than crude oil or natural gas.

1.3.3 Tar Sand Bitumen Tar sands are oil traps not deep enough in the Earth to allow for geological conversion into the conventional oil. This oil was not heated enough to complete the process of molecular breakage to reduce the viscosity. The oil has the characteristics of bitumen and is mixed with large amounts of sand due to the proximity to the surface. The tar sand is mined, flooded with water in order to separate the heavier sand, and then processed in special refineries to reduce its high sulfur content (the original oil usually has 3–5% sulfur) and other components. This process requires huge amounts of energy and water. Only oil deposits in deep layers below 75 m are mined in situ (COSO, 2007).

1.4 Renewable Energy Sources There are five principal renewable energy sources (RES): biomass, flowing water, heat from within the earth, the wind, and the Sun. Biomass shortly describes all plants, trees and organic matter on the Earth. Flowing water is a product of the planet’s climate and geography, where modern hydroturbines use water power to generate hydroelectricity. Heat from deep within the Earth is called geothermal energy, and where the temperatures are hot enough, geothermal energy can be used to generate electricity. Natural conditions of climate and geography produce the winds that blow across the landscape, and like hydropower, modern day wind turbines produce electricity. Another renewable source is solar energy, which is simply energy that comes directly from the Sun. The Sun is a constant natural source of heat and light, and its radiation can be converted into electricity. Figure 1.4 shows the percentage of each renewable energy source used in the world (Demirbas, 2006a). The distribution of renewable energy consumption as percentage of total renewable energy in the world is: biomass 46%, hydroelectric 45%, geothermal 6%, wind 2%, and solar 1%. All renewable energy sources can be used to produce electricity. Solar energy and geothermal energy can supply both electricity and heat. Biomass can supply all three forms of useful energy. RES are derived from those natural, mechanical, thermal and growth processes that repeat themselves within our lifetime and may be relied upon to produce predictable quantities of energy when required. Table 1.11 shows the renewable energy sources and their forms of usage (Demirbas, 2006a). Renewable energy scenarios depend on environmental protection, which is an essential characteristic of sustainable developments. Worldwide biomass ranks fourth as an energy resource, providing approximately 14% of the world’s energy needs. Biomass, mainly now represent only 3% of primary energy consumption

1.4  Renewable Energy Sources

19

Geothermal Solar Wind

Municipal solid wastes Wood in households

Hydro District heating Biomass/Wastes 63%

Wood in industry Power stations Liquid biofuels Biogas

Fig. 1.4  Distribution of each renewable energy source in 1995

Table 1.11  The main renewable energy sources and their usage Energy source

Energy conversion and usage options

Hydropower

Power generation

Modern biomass

Heat and power generation, pyrolysis, gasification, digestion

Geothermal

Urban heating, power generation, hydrothermal, hot dry rock

Solar

Solar home system, solar dryers, solar cookers

Direct solar

Photovoltaics, thermal power generation, water heaters

Wind

Power generation, wind generators, windmills, water pumps

Wave

Numerous designs

Tidal

Barrage, tidal stream

in industrialized countries. However, much of the rural population in developing countries, which represents about 50% of the world’s population, is reliant on biomass, mainly in the form of wood, for fuel (Ramage and Scurlock, 1996). Since the oil crisis of 1973, considerable progress has been made in the search for alternative energy sources. In the early 1970s, with the first oil price shock, interest in renewable energy resources re-emerged. Renewable fuels (re-fuels) are the major alternatives to conventional fossil fuels. Renewable energy is a clean or inexhaustible energy like hydrogen energy or nuclear energy. The most important benefit of renewable energy systems is the decrease of environmental pollution. The uses of renewable energy sources (RES) instead of conventional energy sources have controlled social, economical and environmental problems (Akella et al., 2009). RES contributed 2% of the world’s energy consumption in 1998, including 7 exajoules (EJ) from modern biomass and

20

1  Introduction

2 EJ for all other renewables (UNDP, 2004). RES are readily available in nature. Increasing atmospheric concentrations of greenhouse gasses increase the amount of heat trapped (or decrease the heat radiated from the Earth’s surface), thereby raising the surface temperature of the Earth. About 98% of carbon emissions result from fossil fuel combustion. Reducing use of fossil fuels would considerably reduce the amount of carbon dioxide produced, as well as reducing the levels of the pollutants. Indeed, much of the variation in cost estimates to control carbon emissions revolves around the availability and cost of carbon-free technologies and carbon-reducing technologies, such as energy efficiency and energy conservation equipment. This can be achieved by either using less energy altogether, or using alternative energy resources. Much of the current effort to control such emissions focuses on advancing technologies that emit less carbon or no carbon at all, including nuclear, hydrogen, solar, wind, geothermal, other RES. Focus has also shifted to using energy more efficiently, and to developing innovative technologies and strategies to capture and dispose of carbon dioxide emitted during fossil fuel combustion. Renewable energy is a promising alternative solution because it is clean and environmentally safe. They also produce lower or negligible levels of greenhouse gases and other pollutants when compared with the fossil energy sources they replace. Table 1.12 shows the global renewable energy scenario until 2040. Approximately, half of the global energy supply will be from renewables by 2040, according to the European Renewable Energy Council (EREC, 2006). The most significant developments in renewable energy production are observed in photovoltaics (from 0.2 to 784 Mtoe) and wind energy (from 4.7 to 688 Mtoe) between 2001 and 2040. Table 1.12  Future global renewable energy estimates

Total consumption (million ton oil equivalent) Biomass

2001

2010

2020

2030

2040

10 038

10 549

11 425

12 352

13 310

1080

1313

1791

2483

3271

Large hydropower

22.7

266

309

341

358

Geothermal

43.2

86

186

333

493

Small hydropower

9.5

19

49

106

189

Wind

4.7

44

266

542

688

Solar thermal

4.1

15

66

244

480

Photovoltaic

0.2

2

24

221

784

Solar thermal electricity

0.1

0.4

3

16

68

Marine (tidal/wave/ocean)

0.05

0.1

0.4

3

20

1365.5

1745.5

2694.4

4289

6351

13.6

16.6

23.6

Total renewable energy sources Renewable energy sources contribution (%)

34.7

47.7

1.4  Renewable Energy Sources

21

RES are available throughout the world. The RES are peaceful energy sources for every country—poor or rich, developing or developed. The RES offer a number of technical and environmental benefits over conventional fossil fuels, which make them attractive as alternatives for energy needs. As before, the energy system based on fossil fuels is unsustainable due to equity issues as well as environmental, economic, and geopolitical concerns that will have implications far into the future. Hence, sustainable RES such as biomass, hydropower, wind, solar, geothermal, and marine energy sources will play an important role in the world’s future energy supply.

1.4.1 Biomass Biomass resources include wood and wood wastes, agricultural crops and their waste byproducts, municipal solid waste, animal wastes, waste from food processing and aquatic plants and algae. Biomass has been recognized as a potential source for the renewable energy to substitute the declining fossil fuel resources. The majority of biomass energy is produced from wood and wood wastes (64%), followed by municipal solid waste (24%), agricultural waste (5%), and landfill gases (5%). Most biomass consists of hemicelluloses, cellulose, lignin and minor amounts of other organics. Biomass is used to meet a variety of energy needs, including generating electricity, heating homes, fueling vehicles and providing process heat for industrial facilities. The conversion technologies for utilizing biomass can be separated into four basic categories: direct combustion processes, thermochemical processes, biochemical processes and agrochemical processes. Thermochemical conversion processes can be subdivided into gasification, pyrolysis, direct liquefaction and supercritical fluid liquefaction. There are three ways to use biomass. It can be burned to produce heat and electricity, changed to gas-like fuels such as methane, hydrogen and carbon monoxide, or converted to a liquid fuel. Liquid fuels, also called biofuels, are predominantly two forms of alcohol: ethanol and methanol. Because biomass can be converted directly into a liquid fuel, it could someday supply much of our transportation fuel needs for cars, trucks, buses, airplanes, and trains. This is very important because nearly one-third of our nation’s energy is now used for transportation. Biomass today represents only 3% of the energy consumed in industrialized countries. However, much of the rural population in developing countries, which represents about 50% of the world’s population, relies on biomass, mainly in the form of wood, for fuel. Biomass accounts for 35% of primary energy consumption in developing countries, raising the world total to 14% of primary energy consumption (Demirbas, 2005a). The importance of biomass varies significantly in different world regions, as shown in Table 1.13. In Europe, North America and the Middle East, the share of biomass averages 2 to 3% of total final energy consumption, whereas in Africa, Asia and Latin America, which together account for three-quarters of the world’s population, biomass provides a substantial share of the energy

22

1  Introduction

Table 1.13  The importance of biomass in different world regions Region

Share of biomass in final energy consumption

Africa (average)

62.0

Burundi

93.8

Ethiopia

85.6

Kenya

69.6

Somalia

86.5

Sudan

83.7

Uganda

94.6

South Asia (average)

56.3

East Asia (average)

25.1

China

23.5

Latin America (average)

18.2

Europe (average)

3.5

North America (average)

2.7

Middle East (average)

0.3

needs: a third on average, but as much as 80–90% in some of the poorest countries of Africa and Asia (e.g., Angola, Ethiopia, Mozambique, Tanzania, Democratic Republic of Congo, Nepal and Myanmar). Indeed, for large portions of the rural populations of developing countries, and for the poorest sections of urban populations, biomass is often the only available and affordable source of energy for basic needs such as cooking and heating (Demirbas, 2005a). The term “modern biomass” is generally used to describe the traditional biomass use through the efficient and clean combustion technologies and sustained supply of biomass resources, environmentally sound and competitive fuels, heat and electricity using modern conversion technologies. Ethanol and fatty acid (m)ethylester (biodiesel), as well as diesel produced from biomass by Fischer–Tropsch synthesis, are modern biomass-based transportation fuels. Modern biomass produced in a sustainable way excludes traditional uses of biomass as fuelwood and includes electricity generation and heat production, as well as transportation fuels, from agricultural and forest residues and solid waste. On the other hand, “traditional biomass” is produced in an unsustainable way and it is used as a non-commercial source— usually with very low efficiencies for cooking in many countries (Goldemberg and Coelho, 2004). Biomass can be thermochemically converted into liquid fuel, gases, such as methane, carbon monoxide, or hydrogen by pyrolysis. Bioethanol can be obtained from cellulosic biomass by fermenting and distilling sugar solutions. Vegetable oils such as soybean and canola oils can be chemically converted into liquid fuel known as biodiesel. These fuels can be used as diesel fuel and gasoline in conventional engines with little modification to the system. Certain organic compounds, specifi-

1.4  Renewable Energy Sources

23

cally municipal biosolids (sewage) and animal wastes (manures) can be biochemically converted into methane by anaerobic digestion. Energy crops, especially liquid biofuel (vegetable oils and biodiesels) crops have the potential to be substituted for a fraction of petroleum distillates and petroleum-based petrochemicals in the near future (Hamelinck and Faaij, 2002). In the future, biomass has the potential to provide a cost-effective and sustainable supply of energy, while at the same time aiding countries in meeting their greenhouse gas reduction targets. In the short to medium term, biomass is expected to dominate energy supply. For the generation of electricity and heat, while using advanced combustion technology, organic wastes can be used as modern biomass. Also a number of crops and crop residues may fit modern bioenergy chains (Pimentel et al., 1981; Haberl and Geissler, 2000; Hoogwijk et al., 2003). In industrialized countries, the main biomass processes expected to be utilized in the future are direct combustion of residues and wastes for electricity generation, bioethanol and biodiesel as liquid fuels, and combined heat and power production from energy crops. In the short to medium term, biomass waste and residues are expected to dominate the biomass supply, to be substituted by energy crops in the longer term. The future of biomass electricity generation lies in biomass integrated gasification/gas turbine technology, which offers high energy conversion efficiencies. The electricity is produced by direct combustion of biomass, advanced gasification and pyrolysis technologies, which are almost ready for commercial-scale use. Biomass is burned to produce steam and the steam turns a turbine and drives a generator, producing electricity. Because of potential ash build-up (which fouls boilers, reduces efficiency and increases costs), only certain types of biomass materials are used for direct combustion. Gasifiers are used to convert biomass into a combustible gas (biogas). The biogas is then used to drive a high-efficiency, combined-cycle gas turbine. Heat is used to thermochemically convert biomass into a pyrolysis oil. The oil, which is easier to store and transport than solid biomass material, is then burned like petroleum to generate electricity. Pyrolysis can also convert biomass into phenolic oil, a chemical used to make wood adhesives, molded plastics and foam insulation. Wood adhesives are used to glue together polywood and other composite wood products. Biomass can also be converted into transportation fuels such as ethanol, methanol, biodiesel and additives for reformulated gasoline. Biofuels are used in pure form or blended with gasoline (Demirbas, 2004). 1.4.1.1 Biohydrogen from Biomass Since hydrogen is not a primary fuel, it must be manufactured from water with either fossil or non-fossil energy sources. Widespread use of hydrogen as an energy source could improve global climate change, energy efficiency, and air quality. The thermochemical conversion processes, such as pyrolysis, gasification and steam gasification are available for converting the biomass to a more useful energy. The yield from steam gasification increases with increasing water-to-sample ratio. The yields of hydrogen from the pyrolysis and the steam gasification increase with increasing of temperature. The list of some biomass material used for hydrogen

24

1  Introduction

production is given in Table  1.14. Hydrogen-powered fuel cells are important in enabling technology for the hydrogen future and more efficient alternatives to the combustion of gasoline and other fossil fuels. Hydrogen has the potential to solve two major energy problems: reducing dependence on petroleum and reducing pollution and greenhouse gas emissions. Hydrogen is currently more expensive than conventional energy sources. There are different technologies presently being practiced to produce hydrogen economically from biomass. Hydrogen can be produced by pyrolysis from biomass (Arni, 2004). It can be burned to produce heat or passed through a fuel cell to produce electricity. Biohydrogen technology will play a major role in future because it can utilize renewable sources of energy (Nath and Das, 2003). Biological generation of hydrogen (biohydrogen) technologies provide a wide range of approaches to generate hydrogen, including direct biophotolysis, indirect biophotolysis, photofermentations, and dark fermentation (Levin et al., 2004). Biological hydrogen production processes are found to be more environmental friendly and less energy intensive as compared to thermochemical and electrochemical processes (Das and Veziroglu, 2001). Researchers have been investigating hydrogen production with anaerobic bacteria since the 1980s (Nandi and Sengupta, 1998; Chang et al., 2002). The three types of microorganisms that generate hydrogen are: cyanobacteria, anaerobic bacteria, and fermentative bacteria. The cyanobacteria directly decompose water into hydrogen and oxygen in the presence of light energy by photosynthesis. Photosynthetic bacteria use organic substrates like organic acids. Anaerobic bacteria use organic substances as the sole source of electrons and energy, converting them into hydrogen. Biohydrogen can be generated using bacteria such as Clostridia, by adjusting temperature, pH control, reactor hydraulic retention time (HRT) and other factors of the treatment system. Biological hydrogen can be generated from plants by biophotolysis of water using microalgae (green algae and cyanobacteria), fermentation of organic comTable 1.14  List of some biomass material used for hydrogen production Biomass species

Main conversion process

Bionut shell

Steam gasification

Olive husk

Pyrolysis

Tea waste

Pyrolysis

Crop straw

Pyrolysis

Black liquor

Steam gasification

Municipal solid waste

Supercritical water extraction

Crop grain residue

Supercritical fluid extraction

Pulp and paper waste

Microbial fermentation

Petroleum basis plastic waste

Supercritical fluid extraction

Manure slurry

Microbial fermentation

1.4  Renewable Energy Sources

25

pounds, and photodecomposition of organic compounds by photosynthetic bacteria. To produce hydrogen by fermentation of biomass, a continuous process using a non-sterile substrate with a readily available mixed microflora is desirable (Hussy et al., 2005). A successful biological conversion of biomass to hydrogen depends strongly on the processing of raw materials to produce feedstock, which can be fermented by the microorganisms (de Vrije et al., 2002). Hydrogen production from the bacterial fermentation of sugars has been examined in a variety of reactor systems. Hexose concentration has a greater effect on H2 yields than the HRT. Flocculation also was an important factor in the performance of the reactor (Van Ginkel and Logan, 2005). Hydrogen gas is a product of the mixed acid fermentation of Escherichia coli, the butylene glycol fermentation of Aerobacter, and the butyric acid fermentations of Clostridium spp. (Aiba et al., 1973). Anaerobic fermentation was conducted to improve hydrogen fermentation of food waste in a leaching-bed reactor by heatshocked anaerobic sludge, and also to investigate the effect of dilution rate on the production of hydrogen and metabolites in hydrogen fermentation (Han and Shin, 2004).

1.4.2 Hydropower The water in rivers and streams can be captured and turned into hydropower (HP), also called hydroelectric power. HP currently provides about 17% of the world’s electricity supply, virtually all of Norway’s electricity and more than 40% of the electricity used in developing countries. However, there is great potential in hydropower worldwide. Norway produces more than 99% of its electricity with hydropower. New Zealand uses hydropower for 75% of its electricity. HP provides more than 97% of all electricity generated by renewable sources. Other sources, biomass, geothermal, solar and wind account for less than 3% of renewable electricity production. When the electricity share of total energy consumption is considered, the increase becomes even more dramatic. Hydroelectricity, at present the most important of the clean, economically feasible, renewable energy options, can benefit from a water resources development project; however, that is seldom the only benefit. It is clear, therefore, that hydropower has an important role to play in the future, both in terms of energy supply and water resources development. There is no universal consensus on the definition of small hydropower. Some countries of the European Union such as Portugal, Spain, Ireland, Greece, and Belgium accept 10 MW as the upper limit for installed capacity. In Italy the limit is 3 MW, in France 8 MW, in the UK 5 MW, in Canada 20–25 MW, in the United States 30 MW; however, a value of up to 10 MW total capacity is becoming the generally accepted amount considered as small hydropower in the rest of the world. If total installed capacity of any hydropower system is bigger than 10 MW, it is generally accepted as a large hydropower system (Demirbas, 2006a). Small hydropower can be further subdivided into minihydro, usually defined as less than 500 kW and

26

1  Introduction

microhydro, less than 100 kW. Small hydropower is one of the most valuable energy sources used for electricity in rural comminutes. Small hydroelectricity growth is to decrease the gap of decentralized production for private sector and municipal activity production. Small-scale hydropower systems supply energy from the flowing or running water and convert it to electrical energy. Small hydropower systems depend on the water flow where the resource exists. If a well-designed small hydropower system is established anywhere, it can fit in with its surroundings and will have minimal negative impacts on the environment. Small hydropower systems allow for self-sufficiency by using natural water resources, which are sometimes scarce. These systems supply low-cost energy production applied in many developing countries in the world. There are two small-scale HP systems: microhydropower systems (MHP) with capacities below 100 kW and SHP systems with capacity between 101 kW and 1  MW. The MHP systems, which use cross-flow turbines and Pelton wheels can provide both direct mechanical energy and electrical energy. However, due to design constraints, turbines up to a capacity of only 30 kW are suitable for extracting mechanical energy. Of the total installed capacity of about 12 MW of MHP systems, half is used solely for crop processing. The most popular of the MHP systems is the peltric set, which is an integrated Pelton turbine and electricity generation unit with an average capacity of 1 kW. MHP systems are sometimes described as those having capacities below 100 kW, minihydropower plants are those ranging from 100 to 1000 kW, and the SHP plants are those that produce from 1 to 30 MW. Dams are individually unique structures and dam construction represents the largest structures of basic infrastructure in all nations. The construction of a dam and power plant, along with the impounding of a reservoir, creates certain social and physical changes. The total installed capacity of HP is 640 000 MW (26% of the theoretical potential), generating an estimated 2380 TWh/year in the world, producing nearly 20% of the total global supply of electricity. Hydropower provides unique benefits, rarely found in other sources of energy. These benefits can be attributed to the electricity itself, or to side-benefits, often associated with reservoir development. Principles of sustainable development of particular relevance to energy provision include: improving the well-being of entire populations, ensuring that development is people-centered, participatory and equitable; integrating environmental concerns into decision-making processes; and taking into account the full range of costs and benefits of development. Investment costs for SHP plants vary according to site-specific and local characteristics. The most important system and cost elements are: (1) civil engineering, (2) equipment, and (3) turbine. The electrical generator represents less than 5% of the total cost of a power plant and the efficiency of generators for new plants is already close to 100%. However, standardization of generator equipment for small hydropower could further reduce installation and maintenance costs. Despite the recent debates, few would disclaim that the net environmental benefits of hydropower are far superior to fossil-based generation. Hydroelectricity is produced for an average of 0.85 US ¢ per kWh. In comparison with hydropower, thermal plants take less time to design, obtain approval, build and recover investment.

1.4  Renewable Energy Sources

27

The remaining economically exploitable potential is about 5400  TWh/yr. An investment of at least US $ 1500 billion would be necessary to realize such a program. For a mean level of hydropower plants capacity in the range of 50 to 100 MW, some 20 000 plants would need to be built. In order to implement a plant construction program of this magnitude, a great deal of work (technical, financial and political) would need to be accomplished by all the investments involved, particularly in Asia, South America and Africa (Demirbas, 2006a).

1.4.3 Geothermal As an energy source, geothermal energy has come of age. Geothermal energy for electricity generation has been produced commercially since 1913, and for four decades on the scale of hundreds of megawatts both for electricity generation and direct use. Utilization has increased rapidly during the last three decades, where it can be put to work in various forms such as electricity generation, direct use, space heating, heat pumps, greenhouse heating, and industrial. In 2000, geothermal resources have been identified in over 80 countries and there are quantified records of geothermal utilization in 58 countries (Fridleifsson, 2001). The world’s top countries using geothermal energy directly are given in Table 1.15. In Tuscany, Table 1.15  The world’s top countries using geothermal energy in direct uses. Adapted from Demirbas (2008) Country

Installed MWt

Production (GWh/yr)

China

2282

10 531

Japan

1167

7482

USA

3766

5640

Iceland

1469

5603

Turkey

820

4377

New Zealand

308

1967

Georgia

250

1752

Russia

308

1707

France

326

1360

Sweden

377

1147

Hungary

473

1135

Mexico

164

1089

Italy

326

1048

Romania

152

797

Switzerland

547

663

28

1  Introduction

Italy, a geothermal plant has operated since the early 1900s. There are also geothermal power stations in the USA, New Zealand and Iceland. In Southampton (UK) there is a district heating scheme based on geothermal energy, where hot water is pumped up from about 1800 m below ground. This and other methods have added to the rapid increase of utilization of geothermal energy in the past three decades. Geothermal energy is clean, cheap and renewable, and can be utilized in various forms such as space heating and domestic hot water supply, CO2 and dry-ice production process, heat pumps, greenhouse heating, swimming and balneology (therapeutic baths), industrial processes and electricity generation. In terms of using geothermal energy directly, the main types of use are bathing, swimming and balneology (42%), space heating (35%), greenhouses (9%), fish farming (6%), and industry (6%) (Fridleifsson, 2001). Electricity is produced with geothermal steam in 21 countries spread over all continents, where electricity generation is improving faster in geothermal energy-rich countries. Low-temperature geothermal energy is exploited in many countries to generate heat, with an estimated thermal capacity of about 10 000 MW. From above, direct application of geothermal energy can involve a wide variety of end-uses, such as heating and cooling homes, industrial processes, greenhouses, fish farming, and health spas. It uses mostly existing technology and straightforward engineering. The technology, reliability, economics, and environmental acceptability of direct use of geothermal energy have been demonstrated throughout the world. The total global installed geothermal electric capacity was 7304  MWe in 1996. In much of the world, electricity from fossil fuel-burning electricity plants can be constructed at half the cost of new geothermal electricity. A comparison of the renewable energy sources shows the current electrical energy cost to be 2–10 US ¢ per kWh for geothermal and hydropower, 5–13 US ¢ per kWh for wind, 5–15  US ¢ per kWh for biomass, 25–125  US ¢ per kWh for solar photovoltaic and 12–18 US ¢ per kWh for solar thermal electricity. Of the total electricity production from renewables of 2826  TWh in 1998, 92% came from hydropower, 5.5% from biomass, 1.6% from geothermal and 0.6% from wind. Solar electricity contributed 0.05% and tidal 0.02%. Geothermal energy is a power source that produces electricity with minimal environmental impact, and with its proven technology and abundant resources, can make a significant contribution towards reducing the emission of greenhouse gases (Demirbas, 2006a).

1.4.4 Wind Energy from the wind has been used for centuries to power windmills to mill wheat or pump water. More recently large wind turbines have been designed to generate electricity. This source of energy is non-polluting and freely available in many areas. Wind turbines are becoming more efficient, and therefore the cost of the electricity they generate is falling.

1.4  Renewable Energy Sources

29

Wind power has long been used for grain-milling and water-pumping applications. Significant technical progress since the 1980s, driven by advances in aerodynamics, materials, design, controls, and computing power, has led to economically competitive electrical energy production from wind turbines. Technology development, favorable economic incentives (due to its early development status and environmental benefits), and increasing costs of power from traditional fossil sources have led to significant worldwide sales growth since the early 1980s (Kutz, 2007). There are wind farms around the world. Because the UK is on the edge of the Atlantic Ocean it has one of the best wind resources in Europe. Offshore wind farms in coastal waters are being developed because winds are often stronger blowing across the sea. Turbines can produce between 500 kW and 1 MW of electricity. Production of wind-generated electricity has risen from practically zero in the early 1980s to more than 7.5 TWh per year in 1995. This increase led to a peak in the global cumulative generating capacity of 6500 MW in late 1997 (Garg and Datta, 1998). Wind energy is a significant resource; it is safe, clean, and abundant. Wind energy is an indigenous supply, permanently available in virtually every nation in the world. Figure 1.5 shows the growth in the global wind turbine installed capacity. Globally, wind power generation more than quadrupled between 1999 and 2005. Wind energy is abundant, renewable, widely distributed, clean, and mitigates the greenhouse effect if it is used to replace fossil fuel-derived electricity. Wind energy has limitations based on geography and meteorology, plus there may be political or environmental problems (e.g., dead birds) with erecting turbines (Garg and Datta, 1998). On the other hand, wind can cause air pollution by degradation and distribution of pieces of pollutants such as waste paper, straw, etc. Figure 1.6 shows the growth scenarios for global installed wind power (IEA, 2006). An advantage of wind turbines over some forms of renewable energy is that they can produce electricity whenever the wind blows (at night and also during the

Installed global capacity, GW

60 50 40 30 20 10 0 1991

1993

1995

1997 1999 Year

Fig. 1.5  Growth in world wind turbine installed capacity

2001

2003

2005

30

1  Introduction

Installed global capacity, GW

220

180

140

100

60 2010

2015

2020 Year

2025

2030

Fig. 1.6  Growth scenarios for global installed wind power

day). In theory, wind systems can produce electricity 24 hours every day, unlike PV systems that can not make power at night. However, even in the windiest places, the wind does not blow all the time. So while wind farms do not need batteries for backup storage of electricity, small wind systems do need backup batteries. Wind power in coastal and other windy regions is promising as well. By any measure the power in the wind is no longer an alternative source of energy.

1.4.5 Solar Solar energy is defined as the radiant energy transmitted by the Sun and intercepted by Earth. It is transmitted through space to Earth by electromagnetic radiation with wavelengths ranging between 0.20 and 15 μm. The availability of solar flux for terrestrial applications varies with season, time of day, location, and collecting surface orientation. In this section, we shall treat these matters analytically (Kutz, 2007). Energy comes from processes called solar heating (SH), solar home heating (SHH), solar dryer (SD), solar cooker (SC), solar water heating (SWH), solar photovoltaic (SPV) which converts sunlight directly into electricity, and solar thermal electric power (STEP), when the Sun’s energy is concentrated to heat water and produce steam, which is used to generate electricity. The major component of any solar energy system is the solar collector. Solar energy collectors are special kinds of heat exchangers that transform solar radiation energy to internal energy of the transport medium. Solar dryers are used for drying fruits and spices. The three most popular types of SD are box type, cabinet type, and tunnel type. Box type uses direct heat for

1.4  Renewable Energy Sources

31

dehydration. In cabinet-type dryers, air heated by the collector dehydrates the food product, whereas in tunnel-type dryers forced air circulation is used to distribute heat for dehydration. Cabinet and tunnel type dryers yield a high quality of dried products but they are very bulky and costly compared to the box-type dryers. Of about 800 dryers disseminated so far, 760 are of the box type (Pokharel, 2003). Solar energy systems are solar home systems, solar photovoltaic (SPV) systems, solar water heating (SWH) systems, solar dryers, and solar cookers. These systems are installed and managed by a household or a small community. A solar home system is a PV system with a maximum capacity of 40 W. One of the most abundant energy resources on the surface of the Earth is sunlight. Today, solar energy has a tiny contribution to the total global primary energy supply of less than 1%. Photovoltaic (PV) systems, other than solar home heating systems, are used for communication, water pumping for drinking and irrigation, and electricity generation. The total installed capacity of such systems is estimated at about 1000 kW. A solar home heating system is a solar PV system with a maximum capacity of 40 W. These systems are installed and managed by a household or a small community (Garg and Datta, 1998). Like wind power markets, PV markets have seen rapid growth and costs have fallen dramatically. The total installed capacity of such systems is estimated at about 1000 kW. The PV installed capacities are growing at a rate of 30% per year (Demirbas, 2005a). Solar PV systems have been found to be a promising energy in future. One of the most significant developments in renewable energy production is observed in PVs (EWEA, 2005; Reijnders, 2006). The PV will then be the largest renewable electricity source with a production of 25.1% of global power generation in 2040 (EWEA, 2005). A solar thermal electricity power system is a device that uses solar radiation for the generation of electricity through the solar thermal conversion (Xiao et al., 2004). Figure 1.7 shows the plot for electricity costs from solar thermal power plants. Solar thermal electricity may be defined as the result of a process by which directly collected solar energy is converted to electricity through the use of some sort of heat to electricity conversion device (Mills, 2004). The last three decades have witnessed a trend in solar thermal electricity generation of increasing the concentration of sunlight (Kribus, 2002). There are three main systems of solar thermal electricity: solar towers, dishes and the parabolic troughs (Zhang et al., 1998). Solar thermal power stations based on parabolic and heliostat trough concentrating collectors can soon become a competitive option on the world’s electricity market (Trieb, 2000). Table 1.16 shows the economics and emissions of conventional technologies compared with solar power generation. It has been estimated that a proposed solar system has a net fuel-to-electricity efficiency higher than 60% even when both the energy to produce high-pressure oxygen and to liquefy the captured CO2 are taken into account (Kosugi and Pyong, 2003). Based on future trends, it is foreseen that by the year 2025, the PV electricity would be more economical than fossil fuel electricity (Muneer et al., 2005). A mathematical model for simulating an innovative design of a solar-heated anaerobic digester has been developed by Axaopoulos et al. (2001).

32

1  Introduction

0.6

Electricity cost, US$/kWh

0.5 0.4 0.3 0.2 0.1 0 1980

1985

1990

1995

2000

Year Fig. 1.7  Plot for electricity costs from solar thermal power plants

Table 1.16  Economics and emissions of conventional technologies compared with solar power generation. Adapted from Demirbas (2006a)

Electricity generation technology Solar thermal and solar PV systems Pulverized coal–natural gas turbine

Carbon emissions

Generation costs

g C/kWh

US ¢ per kWh

0 100–230

9–40 5–7

Table 1.17  Properties of common solar collectors Type

Absorber

Motion

Temperature range, K

Flat plate collector

Flat

Stationary

300–350

Compound parabolic collector

Tubular

Stationary

330–510

Cylindrical trough collector

Tubular

Single-axis tracking

330–575

Parabolic trough collector

Tubular

Single-axis tracking

330–575

Parabolic dish collector

Point

Two-axis tracking

275–775

Heliostat trough collector

Point

Two-axis tracking

425–1260

A historical introduction into the uses of solar energy was attempted followed by a description of the various types of collectors including flat-plate, compound parabolic, evacuated tube, parabolic trough, Fresnel lens, parabolic dish and heliostat field collectors (Kalogirou, 2004a, 2004b). Solar thermal electricity systems utilize

1.4  Renewable Energy Sources

33

solar radiation to generate electricity by the photothermal conversion method. There are basically two types of solar collectors: non-concentrating (stationary type) and concentrating. The properties of common solar collectors are given in Table 1.17. Temperatures exceeding about 2300 K should be feasible, given appropriate concentration of the incident sunlight. The theoretical limit on the concentration of sunlight is about 40 000 (Kribus, 2002). A solar thermal conversion system with heliostat trough collector can achieve temperatures in excess of 2000 K. Solar-supported power plants (SSPPs) use technology that is similar to that used in coal-fired power plants. For example, SSPPs use similar steam turbine generators and fuel delivery systems. Electricity costs are in the 9 to 40 US ¢ per kWh range (Table  1.16). The feasibility of combining gas and steam expansion in a power cycle has been extensively explored (Sorensen, 1983). Concentrated solar energy is used to produce steam, the steam turns a turbine and drives a generator, producing electricity. Solar radiation can be used as a primary energy source or as a secondary energy source to power gas turbines.

1.4.6 Other Renewable Energy Sources Wave power, tidal power, municipal solid waste, gas from animal wastes (biogas), landfill, peat energy and ocean thermal energy conversion (OTEC) are the other renewable energy sources (RES). Water energy sources are hydropower, tidal and wave technologies. Marine energy sources include current, tidal, ocean thermal energy conversion (OTEC) and wave technologies. The world wave resource is between 200 and 5000 GW mostly found in offshore locations (Garg and Datta, 1998). Wave energy converters fixed to the shoreline are likely to be the first to be fully developed and deployed, but waves are typically two to three times more powerful in deep offshore waters than at the shoreline. Wave energy can be harnessed in coastal areas, close to the shore. The first patent for a wave energy device was filed in Paris in 1799, and by 1973 there were 340 British patents for wave energy devices. By comparison to wind and PV, wave energy and tidal stream are very much in their infancy. Currently, around 1 MW of wave energy devices are installed worldwide, mainly from demonstration projects. Water is a renewable energy source, which can be used in electricity generation by using its lifting force (buoyant force). It is an important electricity generating apparatus, using gravity and buoyancy, which can curtail costs of power generation and prevent environmental pollution and prevent destruction of an ecosystem. The wave conversion plant using buoyancy chambers is another solution for electricity generation using the water lifting force. There are a good many reasons why the water lifting force will be used in the future at many scales of electricity generation. The hydraulic ram is another attractive solution for electricity generation where a large gravity flow exists. Hydraulic ram (hydram) pumps are water lifting or water pumping devices that are powered by filling water. The hydram pumps have been used for over two centuries in many parts of the world. It is a useful device that can

34

1  Introduction

pump water uphill from a flowing source of water above the source with no power requirement except the force of gravity. The ocean thermal energy conversion (OTEC) is an energy technology that converts solar radiation to electric power. OTEC systems use the ocean’s natural thermal gradient to drive a power-producing cycle. As long as the temperature between the warm surface water and the cold deep water differs by about 20 K, an OTEC system can produce a significant amount of power. The oceans are thus a vast renewable resource, with the potential to help us produce billions of watts of electric power. Anaerobic digestion in landfills occurs in a series of stages, each of which is characterized by the increase or decrease of specific bacterial populations and the formation and utilization of certain metabolic products. Landfill gas is typically composed of about 50% methane by volume. Producing energy from landfill gas improves local air quality, eliminates a potential explosion hazard and reduces greenhouse gas emissions to the atmosphere. Hydrogen, produced by passing an electrical current through water, can be used to store solar energy and regenerate it when needed for nighttime energy requirements. The solid waste management practices are collection, recovery and disposal, together with the results of cost analysis. Biogas can be obtained from digesting the organic material of municipal solid wastes (MSW). The composition of MSW varies by the source of waste; however, in all cases the major constituents of MSW are organic in nature and the organics accounts for more than 50% of MSW. The economic exploitation of methane is worthwhile after one year from the start of the landfill operation. Biogas can be obtained from several sources. It is obtained from decomposing organic material. Biogas is composed of methane (CH4), carbon dioxide (CO2), air, ammonia, carbon monoxide, hydrogen, sulfur gases, nitrogen and oxygen. Among its components, methane is the most important one, particularly for the combustion process in vehicle engines. A typical analysis of raw landfill gas is given in Table 1.18. CH4 and CO2 make up around 90% of the gas volume produced. Typically, the main constituents of landfill gas are methane and carbon dioxide, both of which are major contributors to global warming. But, due to the widely varying nature of the contents of landfill sites the constituents of landfill gases vary widely. Table 1.18  Typical analysis of raw landfill gas Component

Chemical formula

Content

Methane

CH4

40–60 (% by vol.)

Carbon dioxide

CO2

20–40 (% by vol.)

Nitrogen

N2

  2–20 (% by vol.)

Oxygen

O2

< 1 (% by vol.)

Heavier hydrocarbons

CnH2n+2

Hydrogen sulfide

H2S

Complex organics

–

< 1 (% by vol.) 40–100 ppm 1000–2000 ppm

1.4  Renewable Energy Sources

35

Oxygen

Nitrogen

Hydrogen

Methane

Carbon dioxide

Composition of the biogas, % by vol.

80 70 60 50 40 30 20 10 0

0

20

40

60 80 Time, month

100

120

Fig. 1.8  Production of biogas components with time in landfill

The generation of municipal solid wastes (MSW) has increased in parallel to rapid industrialization. Approximately 16% of all discarded MSW is incinerated; the remainder is disposed of in landfills. Disposal of MSW in sanitary landfills is usually associated with soil, surface water and groundwater contamination when the landfill is not properly constructed. The flow rate and composition of leachate vary from site to site, seasonally at each site and depending on the age of the landfill. The processing of MSW (i.e., landfill, incineration, aerobic composting) secures many advantages and limitations. The greenhouse gas emissions can be reduced by the uncontrolled releasing of methane from improperly disposed organic waste in a large landfill. Decomposition in landfills occurs in a series of stages, each of which is characterized by the increase or decrease of specific bacterial populations and the formation and utilization of certain metabolic products. The first stage of decomposition, which usually lasts less than a week, is characterized by the removal of oxygen from the waste by aerobic bacteria. In the second stage, which has been termed the anaerobic acid stage, a diverse population of hydrolytic and fermentative bacteria hydrolyzes polymers, such as cellulose, hemicellulose, proteins, and lipids, into soluble sugars, amino acids, long-chain carboxylic acids, and glycerol. The main components of landfill gas are byproducts of the decomposition of organic material, usually in the form of domestic waste, by the action of naturally occurring bacteria under anaerobic conditions. Figure 1.8 shows the production of biogas components with time in a landfill. Methods developed for treatment of landfill leachates can be classified as physical, chemical and biological, which are usually used in combinations in order to improve the treatment efficiency. Biological treatment methods used for the leachate treatment can be classified as aerobic, anaerobic and anoxic processes which are

36

1  Introduction

widely used for the removal of biodegradable compounds (Kargi and Pamukoglu, 2004a). Biological treatment of landfill leachate usually results in low nutrient removals because of high chemical oxygen demand (COD), high ammonium-N content and the presence of toxic compounds such as heavy metals (Uygur and Kargi, 2004). Landfill leachate obtained from the solid waste landfill area contained high COD and ammonium ions which resulted in low COD and ammonium removals by direct biological treatment. Several anaerobic and aerobic treatment systems have been studied in landfill leachate. Leachates contain non-biodegradable substrates, which are not removed by biological treatment alone and an increase of leachate input may cause a reduction in substrate removal (Cecen et al., 2003). Raw landfill leachate has been subjected to pre-treatment by coagulation–flocculation and air stripping of ammonia before biological treatment in order to improve biological treatability of the leachate (Kargi and Pamukoglu, 2004b). In other forms of treatment, natural zeolite and bentonite can be utilized as a novel landfill liner material (Kayabali, 1997).

1.5 Nuclear Fuel Sources Nuclear power plants are based on uranium mined in surface mines, or by in situ leaching. Nuclear energy has been used to produce electricity for more than half a century. Worldwide, nuclear energy accounts for 6% of energy and 16% of electricity, and 23% in OECD countries (UNDP, 2004). OECD countries produce almost 55% of the world’s uranium. The global nuclear energy consumption increased rapidly from 0.1% in 1970 to 7.4% in 1998. This increase was especially high in the 1980s. Fissile materials are defined as materials that are fissionable by neutrons with zero kinetic energy. In nuclear engineering, a fissile material is one that is capable of sustaining a chain reaction of nuclear fission. Nuclear power reactors are mainly fueled with uranium, the heaviest element that occurs in nature in more than trace quantities. The principal nuclear energy sources are uranium-235, plutonium-239, uranium-233 and thorium. Thorium was discovered by Berzelius in 1828. Thorium occurs in thorite and in thorianite. Large deposits of thorium minerals have been reported in New England and elsewhere, but these have yet to be exploited. Thorium is now thought to be about three times as abundant as uranium and about as abundant as lead or molybdenum. The metal is a source of nuclear power. There is probably more energy available for use from thorium in the minerals of the Earth’s crust than from both uranium and fossil fuels. Thorium might serve as a matrix for fissioning or transmuting minor actinides should this be required. The necessity and case for this objective, or for preferring thorium to other matrices, both remain to be established. The essence of a conventional nuclear reactor is the controlled fission chain reaction of U-235 and Pu-239. This produces heat, which is used to make steam which drives a turbine. The chain reaction depends on having a surplus of neutrons to keep it going.

1.5  Nuclear Fuel Sources

37

Work has been done in developing thorium cycle converter-reactor systems. Several prototypes, including the high-temperature gas-cooled reactor (HTGR) and molten salt converter reactor experiment (MSRE), have operated. While the HTGR reactors are efficient, they are not expected to become important commercially for many years because of certain operating difficulties. Thorium is recovered commercially from the mineral monazite, which contains from 3 to 9% ThO2 along with rare-earth minerals. Much of the internal heat the Earth produces has been attributed to thorium and uranium. In the long-term, thorium may well provide a means of resource extension, in parallel with fast-reactor developments rather than as a substitute for them. Meanwhile the most valuable contribution to industry that it can make appears likely to be in extending fuel irradiation where recycling of recovered fissile and fertile values is considered impracticable or undesirable. Thorium has long been recognized as a possible nuclear fuel, since although the natural element consists almost entirely of the non-fissile Th-232, it is fertile in being capable of transmutation by a neutron flux into the fissile uranium-233. In favorable circumstances, given a start with some other neutron source such as U-235, plutonium or an accelerator-driven generator, it can sustain a thermal breeding cycle in which as much fissile material is generated as consumed. This cycle has been adequately demonstrated in principle. Thorium, particularly with breeding, could therefore add to the available nuclear fuel currently dependent on the established uranium cycle. For neutronic reasons, thorium is also somewhat more suited than uranium to HTGRs, which are capable of better thermodynamic efficiencies than the currently dominant water-cooled types, or of serving as sources of process heat. However, uranium is still plentiful, HTGRs have never been commercially deployed, and the thorium cycle has not been widely adopted (Thorn et al., 1983). The technology to utilize thorium in nuclear reactors was thought to be similar to that of uranium. Thorium resources are larger than those of uranium, and neutron yields of U-233 in the thermal and epithermal regions are higher than for Pu-239 in the uranium/plutonium fuel cycle. The introduction of the thorium-based nuclear fuel cycle would therefore vastly enlarge the fissile resources by breeding U-233. Other reasons identified in past studies are the potential for fuel cycle cost reduction, the reduction in U-235 enrichment requirements, safer reactor operation because of lower core excess reactivity requirements, and safer and more reliable operation of ThO2 fuel as compared to UO2 fuel at high burn-up due to the former’s higher irradiation and corrosion resistance (IAEA, 2002). For many years there has been interest in utilizing thorium (Th-232) as a nuclear fuel since it is three times as abundant in the Earth’s crust as uranium. Also, all of the mined thorium is potentially useable in a reactor, compared with the 0.7% of natural uranium, so some 40 times the amount of energy per unit mass might be available. A thorium reactor would work by having Th-232 capture a neutron to become Th-233 which decays to uranium-233, which fissions. The problem is that insufficient neutrons are generated to keep the reaction going. Thorium is also an alpha emitter. Th-232 goes through six alpha and four beta decay steps before becoming the stable isotope Pb-208. Th-232 is sufficiently

38

1  Introduction

radioactive to completely expose a photographic plate in a few hours. Thorium disintegrates with the production of “thoron” (Rn-220), which is an alpha emitter and presents a radiation hazard. Good ventilation of areas where thorium is stored or handled is therefore essential. Several methods are available for producing thorium metal; it can be obtained by reducing thorium oxide with calcium, by electrolysis of anhydrous thorium chloride in a fused mixture of sodium and potassium chlorides, by calcium reduction of thorium tetrachloride mixed with anhydrous zinc chloride, and by reduction of thorium tetrachloride with an alkali metal. The following is a comparison of thorium with uranium as nuclear fuels: • Weapons-grade fissionable material (U-233) is harder to retrieve safely and clandestinely from the thorium reactor than plutonium is from the uranium breeder reactor. • Thorium produces 10 to 10 000 times less long-lived radioactive waste than uranium or plutonium reactors. • Thorium comes out of the ground as a 100% pure, usable isotope, which does not require enrichment, whereas natural uranium contains only 0.7% fissionable U-235. • Because thorium does not sustain chain reaction, fission stops by default if we stop priming it, and a runaway chain reaction accident is improbable. A neutron is captured by 90Th232, which makes it 90Th233: Th232 + 0n1 → 90Th233

90

(1.9)

Th-233 spontaneously emits a beta particle, leaving behind one additional proton, and one fewer neutron. This is called beta decay. Th233 → 91Pa233 + β

90

(1.10)

The element with 91 protons is protactinium (Pa). The isotope 91PA233 also undergoes beta decay, Pa233 → 92U233 + β

91

(1.11)

The U-233 isotope that is produced in step (3) is fissionable, but has fewer neutrons than its heavier cousin, U-235, and its fission releases only 2 neutrons, not 3. U233 + 0n1 → fission fragments + 20n1

92

(1.12)

The priming neutrons are emitted in a process called spallation (interaction of particles with a target), which is the induced splitting of an otherwise non-fissionable large nucleus. The capability of high-current, high-energy accelerators to produce neutrons by spallation from heavy elements has been used in the structural research of such materials. In this process a beam of high-energy protons (usually > 500 MeV) is directed at a high atomic number target such as tungsten, tantalum, depleted uranium, thorium, zirconium, lead, lead-bismuth, mercury and up to one neutron can be produced per 25 MeV of the incident proton beam. The idea is to use a particle accelerator producing neutrons by spallation to feed a fuel/moderator assembly where the neutrons multiply by fission chain reactions.

References 

39

If the energy liberated becomes substantially greater than that needed to drive the accelerator, the process has a net gain and becomes self supporting. Hence this is called an energy amplifier (EA). In the energy amplifier (EA), a proton beam impinges on lead, the high-energy protons splitting lead nuclei, leading to the release of neutrons. If the spallation target is surrounded by a blanket assembly of nuclear fuel, such as fissile isotopes of uranium or plutonium, there is a possibility of sustaining a fission reaction. This is described as an accelerator-driven system (ADS). In this, up to 10% of the neutrons could come from the spallation, though it would normally be less, even where actinide incineration is the main objective (Demirbas, 2005b).

Summary Energy sources are classified into three groups: fossil, fissile and renewable. The term fossil refers to an earlier geologic age. Fossil fuels were formed a great many years ago and are not renewable. The fossil energy sources are petroleum, coal, bitumens, natural gas, oil shales, and tar sands. The main fissile energy sources are uranium and thorium. Conventional fuel sources are petroleum and coal (including lignite). Our modern way of life is intimately dependent upon fossil fuels or mineral fuels. Conventional energy sources based on petroleum and coal have proven to be highly effective drivers of economic progress, but at the same time damaging to the environment and to human health. Renewable energy sources such as wind, solar, biomass and hydropower energy are important today, and they will be important in the future. Hydrogen is seen as the energy carrier of the future. Hydrogen is storable and transferable, has high heat value per mass unit and its sources are globally distributed. Hydrogen is strategically important as it has low emission, is environmentally benign, and represents a cleaner and more sustainable energy system. Hydrogen seems to be the future energy carrier by the virtue of being renewable. Hydrogen is not a primary fuel. It must be manufactured from water with either fossil or non-fossil energy sources. Widespread use of hydrogen as an energy source could improve global climate change, energy efficiency, and air quality. The thermochemical conversion processes, such as pyrolysis, gasification and steam gasification are available for converting the biomass to a more useful energy.

References Aiba, S., Humphrey, A.E., Milis, N.F. 1973. Biochemical engineering, 2nd edn. Academic, New York. Akella, A.K., Saini, R.P., Sharma, M.P. 2009. Social, economical and environmental impacts of renewable systems. Renew Energy 34:390–396. Annual Energy Review (AER) 1999. 2000. Energy Information Administration, US Department of Energy, Washington, DC.

40

1  Introduction

Arni, S. 2004. Hydrogen-rich gas production from biomass via thermochemical pathways. Energy Edu Sci Technol 13:47–54. Axaopoulos, P., Panagakis, P., Tsavdaris, A., Georgakakis, D. 2001. Simulation and experimental performance of a solar heated anaerobic digester. Solar Energy 70:155–164. Cecen, F., Erdincler, A., Kilic, E. 2003. Effect of powdered activated carbon addition on sludge dewaterability and substrate removal in landfill leachate treatment. Advances Environ Res 7:707–713. Chang, J.-S., Lee, K.-S., Lin, P.-J. 2002. Biohydrogen production with fixed-bed bioreactors. Int J Hydrogen Energy 27:1167–1174. COSO (Crude Oil Supply Outlook). 2007. Report to the Energy Watch Group EWG-Series No. 3/2007. http://www.energywatchgroup.org/fileadmin/global/pdf/EWG-Oilreport-10-2007.pdf. Accessed 2009. Das, D., Veziroglu, T.N. 2001. Hydrogen production by biological processes: a survey of literature. Int J Hydrogen Energy 26:13–28. Demirbas, A. 1999. Evaluation of biomass materials as energy sources: upgrading of tea waste by briquetting process. Energy Sources 21:215–220. Demirbas, A. 2004. The importance of biomass. Energy Sources 26:361–366. Demirbas, A. 2005a. Potential applications of renewable energy sources, biomass combustion problems in boiler power systems and combustion related environmental issues. Progress Energy Combus Sci 31:171–192. Demirbas, A. 2005b. Options and trends of thorium fuel utilization in Turkey. Energy Sources 27:597–603. Demirbas, A. 2006a. Energy priorities and new energy strategies. Energy Edu Sci Technol 16:53–109. Demirbas, A. 2006b. The importance of natural gas in the world. Energy Sources Part B:413–420. Demirbas, A. 2007. Utilization of coals as sources of chemicals. Energy Sources 29:677–684. Demirbas, A. 2008. Biodiesel: a realistic fuel alternative for diesel engines. Springer, London. Demirbas, A., Güllü, D. 1998. Acetic acid, methanol and acetone from lignocellulosics by pyrolysis. Energy Edu Sci Technol 2:102–110. de Vrije, T., de Haas, G.G., Tan, G.B., Keijsers, E.R.P., Claassen, P.A.M. 2002. Pretreatment of Miscanthus for hydrogen production by Thermotoga elfıi. Int J Hydrogen Energy 27:1381–1390. Dorf, R.C. 1977. Energy resources and policy. Addison-Wesley, Los Angeles, CA. Dry, M.E. 1999. Fischer–Tropsch reactions and the environment. Appl Catal A General 189:185–190. EREC (European Renewable Energy Council). 2006. Renewable energy scenario by 2040, EREC Statistics, Brussels. EWEA (European Wind Energy Association). 2005. Report: large scale integration of wind energy in the European power supply: analysis, issues and recommendations. EWEA, Brussels, Belgium. Fridleifsson, I.B. 2001. Geothermal energy for the benefit of the people. Renew Sustain Energy Rev 5:299–312. Garg, H.P., Datta, G. 1998. Global status on renewable energy, in Solar Energy Heating and Cooling Methods in Building, International Workshop, Iran University of Science and Technology, 19–20 May 1998. Goldemberg, J., Coelho, S.T. 2004. Renewable energy: traditional biomass vs. modern biomass. Energy Policy 32:711–714. Gorman, J. 2002. Hydrogen: The next generation. Science News 162:235–236. Haberl, H., Geissler, S. 2000. Cascade utilization of biomass: strategies for a more efficient use of a scarce resource. Ecol Eng 16:S111–S121. Hacisalihoglu, B., Demirbas, A.H., Hacisalihoglu, S. 2008. Hydrogen from gas hydrate and hydrogen sulfide in the Black Sea. Energy Edu Sci Technol 21:109–115. Hamelinck, C.N., Faaij, A.P.C. 2002. Future prospects for production of methanol and hydrogen from biomass. J Power Sources 111:1–22.

References 

41

Han, S.-K., Shin, H.-S. 2004. Biohydrogen production by anaerobic fermentation of food waste. Int J Hydrogen Energy 29:569–577. Hoogwijk, M., Faaij, A., van den Broek, R., Berndes, G., Gielen, D., Turkenburg, W. 2003. Exploration of the ranges of the global potential of biomass for energy. Biomass Bioenergy 25:119–133. Hussy, I., Hawkes, F.R., Dinsdale, R., Hawkes, D.L. 2005. Continuous fermentative hydrogen production from sucrose and sugarbeet. Int J Hydrogen Energy 30:471–483. IAEA (International Atomic Energy Agency). 2002. Thorium fuel utilization: options and trends. Proceedings of three IAEA meetings held in Vienna in 1997, 1998 and 1999. IEA (International Energy Annual). 2000. Energy Information Administration, US Department of Energy, Washington, DC. IEA (International Energy Agency). 2006. Key world energy statistics. IEA, Paris. http://www.iea. org/textbase/nppdf/free/2006/key2006.pdf. Accessed 2009. Kalogirou, A.S. 2004a. Environmental benefits of domestic solar energy systems. Energy Convers Manage 45:3075–3092. Kalogirou, A.S. 2004b. Solar thermal collectors and applications. Progress Energy Combus Sci 30:231–295. Kargi, F., Pamukoglu, M.Y. 2004a. Adsorbent supplemented biological treatment of pre-treated landfill leachate by fed-batch operation. Biores Technol 94:285–291. Kargi, F., Pamukoglu, M.Y. 2004b. Repeated fed-batch biological treatment of pre-treated landfill leachate by powdered activated carbon addition. Enzyme Microbial Technol 34:422–428. Kayabali, K. 1997. Engineering aspects of a novel landfill liner material: bentonite-amended natural zeolite. Eng Geology 46:105–114. Kosugi, T., Pyong, S.P. 2003. Economic evaluation of solar thermal hybrid H2O turbine. Energy 28:185–198. Kribus, A. 2002. A high-efficiency triple cycle for solar power generation. Solar Energy 72:1–11. Kutz, M. (Ed.) 2007. Environmentally conscious alternative energy production. Wiley, Hoboken, NJ. Lee, S.-Y., Holder, G.D. 2001. Methane hydrates potential as a future energy source. Fuel Proc Technol 71:181–186. Levin, D.B., Pitt, L., Love, M. 2004. Biohydrogen production: prospects and practical application. Int J Hydrogen Energy 29:173–185. Mills, D. 2004. Advances in solar thermal electricity technology. Solar Energy 76:19–31. Muneer, T., Asif, M., Munawwar, S. 2005. Sustainable production of solar electricity with particular reference to the Indian economy. Renew Sustain Energy Rev 9:444–473. Nandi, R., Sengupta, S. 1998. Microbial production of hydrogen: an overview. Critical Rev Microbiol 24:61–84. Nath, K., Das, D. 2003. Hydrogen from biomass. Current Sci 85:265–271. Pimentel, D., Moran, M.A., Fast, S., Weber, G., Bukantis, R., Balliett, L., Boveng, P., Cleveland, C., Hindman, S., Young, M., 1981. Biomass energy from crop and forest residues. Science 212:1110–1115. Pokharel, S. 2003. Promotional issues on alternative energy technologies in Nepal. Energy Policy 31:307–318. Ramage, J., Scurlock, J. 1996. Biomass, in Renewable energy-power for a sustainable future, G. Boyle (Ed.). Oxford University Press, Oxford. Reijnders, L. 2006. Conditions for the sustainability of biomass-based fuel use. Energy Policy 34:863–876. Schobert, H.H., Song, C. 2002. Chemicals and materials from coal in the 21st century. Fuel 81:15–32. Schulz, H. 1999. Short history and present trends of FT synthesis. Appl Catal A General 186:1–16. Sorensen, H.A. 1983. Energy conversion systems. Wiley, New York. Thorn, J.D., John, C.T., Burstall, R.F. 1983. Nuclear power technology, W. Marshall (Ed.), Vol. 2, Chap. 17, pp. 377–381. Oxford University Press, Oxford.

42

1  Introduction

Trieb, F. 2000. Competitive solar thermal power stations until 2010: the challenge of market introduction. Renew Energy 19:163–171. UNDP (United Nations Development Programme). 2004. World Energy Assessment 2004: Energy and the Challenge of Sustainability. UNDP, New York. Uygur, A., Kargi, F. 2004. Biological nutrient removal from pre-treated landfill leachate in a sequencing batch reactor. J Environ Manage 71: 9–14. WEC (World Energy Council). 2004. Survey of energy resources. WEC, London. Xiao, C., Luo, H., Tang, R., Zhong, H. 2004. Solar thermal utilization in China. Renew Energy 29:1549–1556. Van Ginkel, S.W., Logan, B. 2005. Increased biological hydrogen production with reduced organic loading. Water Res 39:3819–3826. Veziroglu, T. 1975. Hydrogen energy, Part B. Plenum, New York. Vijayaraghavan, K., Soom, M.A.M. 2006. Trends in biohydrogen generation: a review. Environ Sci 3:255–271. Zhang, Q.C., Zhao, K., Zhang, B.C., Wang, L.F., Shen, Z.L., Zhou, Z.J., Lu, D.Q., Xie, D.L., Li, B.F. 1998. New cermet solar coatings for solar thermal electricity applications. Solar Energy 64:109–114.

Chapter 2

Fuels from Biomass

2.1 Introduction The term biomass (Greek bio meaning life + maza meaning mass) refers to nonfossilized and biodegradable organic material originating from plants, animals and microorganisms. The biomass includes products, byproducts, residues and waste from agriculture, forestry and related industries as well as the non-fossilized and biodegradable organic fractions of industrial and municipal solid wastes. Biomass also includes gases and liquids recovered from the decomposition of non-fossilized and biodegradable organic material. According to another definition, the term biomass refers to wood, short-rotation woody crops, agricultural wastes, short-rotation herbaceous species, wood wastes, bagasse, industrial residues, waste paper, municipal solid waste, sawdust, biosolids, grass, waste from food processing, aquatic plants and algae animal wastes, and a host of other materials (Demirbas, 2008a). Biomass is the plant and animal material, especially agricultural waste products, used as a source of fuel. It is a rather simple term for all organic materials that comes from plants, trees, crops and algae. Biomass is commonly recognized as an important renewable energy, where solar energy is stored as chemical energy via photosynthesis during the growth of plants and trees, which can be released via direct or indirect combustion. Figure 2.1 shows the main steps of photosynthetic biomass growth. A useful way to analyze the biosphere system is to trace the work potential, or exergy, of the various energy flows from the sources, such as the Sun, to its eventual destruction in natural decay or human utilization. Photosynthesis is a natural mechanism for capturing and concentrating carbon dioxide directly from the air. Chemical energy and organic carbon are obtained by organisms either directly or indirectly via the photosynthetic conversion of solar energy. These organisms have evolved metabolic machineries for the photochemical reduction of carbon dioxide to organic matter. The majority of the bioengineering strategies for biochemically derived fuels involve options for the disposition of organic matter produced via A. Demirbas, Biohydrogen, © Springer 2009

43

44

2  Fuels from Biomass

photosynthate. The bulk of the presently exploited photosynthate is directed toward the production of wood, food, and feed. During processing and consumption, waste organic materials are generated, which can be used for energy production via combustion, pyrolysis or biochemical conversions to ethanol, hydrogen, methane, and isopropanol. All biomass is produced by green plants converting sunlight into plant material through photosynthesis. Photosynthesis is the fundamental process in biomass energy whereby energy in sunlight is captured and stored in the chemical bonds of the tissues of living plants. Photosynthesis is a carbon fixation reaction by the electrochemical reduction of carbon dioxide. The fixation or reduction of carbon dioxide is a light-independent process. Although some of the steps in photosynthesis are still not completely understood, the overall photosynthetic equation has been known since the 1800s. The productivity of biomass depends on the presence of the required amounts of sunlight, water, and various nutrients, as well as proper environmental conditions including temperature and humidity. The photosynthetic apparatus and the mechanisms by which it operates have been intensively investigated over the past 40 to 50 years. The photosynthesis is that of three series of interconnected oxidation-reduction reactions: The first involves the evolution of oxygen from water. The second is the transfer of H atoms to a primary hydrogen acceptor. The third is the reduction of CO2 to carbohydrates by the primary hydrogen acceptor. The light energy required for photosynthesis is used to drive the H atoms against the potential gradient.

Sunlight

CO2 in atmosphere

H2O

CO2 in atmosphere

Chlorophyll (as catalyst) Electrochemical reduction

Initial photosynthetic substances (CH2O + O2)

Plant food from soil

Biopolymerization

Biomass growth

Fig. 2.1  The main steps of photosynthetic biomass growth

2.2  Biomass Feedstocks

45

The photochemical stage of photosynthesis consists of two separate steps, I and II. The products of light reaction II are an intermediate oxidant and a strong oxidant which is capable of oxidizing water to oxygen. An intermediate oxidant and a strong reductant that can reduce carbon dioxide are produced in light reaction I. The two light reactions involve two pigment systems, photosystems I and II, interconnected by enzymatic reactions coupled with photophosphorylation yielding adenosine triphosphate (ATP).

2.2 Biomass Feedstocks The biosphere processes large amounts of energy of varying types and quality. Biomass feedstocks are marked by their tremendous diversity, which makes them rather difficult to characterize as a whole. Feedstocks that can be utilized with conversion processes are primarily the organic materials now being landfilled. These include forest products wastes, agricultural residues, organic fractions of municipal solid wastes, paper, cardboard, plastic, food waste, green waste, and other waste. Non-biodegradable organic feedstocks, such as most plastics, are not convertible by biochemical processes. Bio-based materials require pre-treatment by chemical, physical, or biological means to open up the structure of biomass. The major categories of biomass feedstock are given in Table 2.1. Biomass is the world’s fourth largest energy source worldwide, following coal, oil and natural gas. Biomass appears to be an attractive feedstock for three main

Table 2.1  Major categories of biomass feedstocks Forest products

Wood, logging residues, trees, shrubs and wood residues, sawdust, bark, etc.

Biorenewable wastes

Agricultural wastes, crop residues, mill wood wastes, urban wood wastes, urban organic wastes

Energy crops

Short-rotation woody crops, herbaceous woody crops, grasses, starch crops, sugar crops, forage crops, oilseed crops, switchgrass, miscanthus

Aquatic plants

Algae, water weed, water hyacinth, reed and rushes

Food crops

Grains, oil crops

Sugar crops

Sugar cane, sugar beets, molasses, sorghum

Landfill

Hazardous waste, non-hazardous waste, Inert waste, liquid waste

Organic wastes

Municipal solid waste, industrial organic wastes, municipal sewage and sludges

Algae

Prokaryotic algae, eukaryotic algae, kelps

Mosses

Bryophyta, polytrichales

Lichens

Crustose lichens, foliose lichens, fruticose lichen

46

2  Fuels from Biomass

reasons. First, it is a renewable resource that could be sustainably developed in the future. Second, it appears to have formidably positive environmental properties by reducing GHG emissions, possibly reducing NOx and SOx depending on the fossil fuels displaced. However, there are also negative impacts, such as the release of polycyclic aromatic hydrocarbons, dioxins, furans, volatile organic compounds, and heavy metals especially when combusted in traditional stoves. Third, it appears to have significant economic potential provided that fossil fuel prices increase in the future. Biomass is a sustainable feedstock for chemicals and energy products that could potentially enhance the energy independence of the world. As an energy source that is highly productive, renewable, carbon-neutral, and easy to store and transport, biomass has drawn worldwide attention recently. Biomass offers important advantages as a combustion feedstock due to the high volatility of the fuel and the high reactivity of both the fuel and the resulting char. However, it should be noted that in comparison with solid fossil fuels, biomass contains much less carbon and more oxygen and has a low heating value. With higher oxygen content than fossil fuels, biomass feedstocks have fundamentally lower energy content. The maximum useful energy that can be theoretically extracted from biomass feedstock is its chemical exergy. Table 2.2 shows the elemental analyses and higher heating value (HHV) of biomass samples. The waste products of a home include paper, containers, tin cans, aluminum cans, and food scraps, as well as sewage. The waste products of industry and commerce include paper, wood, and metal scraps, as well as agricultural waste products. Biodegradable wastes, such as paper fines and industrial biosludge, into mixed alcohol fuels (e.g., isopropanol, isobutanol, isopentanol). The wastes are first treated with lime to enhance reactivity. Then, they are converted to volatile fatty acids (VFAs) such as acetic acid, propionic acid, and butyric acid, using a mixed culture of microorganisms derived from cattle rumen or anaerobic waste treatment facilities. Typical solid wastes include wood material, pulp and paper industry residues, agricultural residues, organic municipal material, sewage, manure, and food processing byproducts. Biomass is considered one of the main renewable energy resources of the future due to its large potential, economic viability and various social and environmental benefits. It is estimated that by 2050 biomass could provide nearly 38% of the world’s direct fuel use and 17% of the world’s electricity. If biomass is produced more efficiently and used with modern conversion technologies, it can supply a considerable range and diversity of fuels at small and large scales. Municipal solid waste (MSW) is defined as waste durable goods, non-durable goods, containers and packaging, food scraps, yard trimmings, and miscellaneous inorganic wastes from residential, commercial, and industrial sources (Demirbas, 2004). Forests are a principal global economic, as well as ecological, resource. Forests have played a big role in the development of human societies. The prime marketable product of most forests is wood for use as timber, fuelwood, pulp and paper, providing some 3.4 billion cubic meters of timber-equivalent per year globally. Asia and Africa use 75% of global wood fuels. The lumber, plywood, pulp, and paper industries burn their own wood residues in large furnaces and boilers to supply 60% of the energy needed to run factories (Demirbas, 2003). Figure 2.2 shows the use

2.2  Biomass Feedstocks

47

Table 2.2  Elemental analyses (wt.%) and calorific values (HHV, MJ/kg) of biomass samples Biomass sample

C

H

O

N

Ash

Higher heating value (MJ/kg)

Olive husk

50.0

6.2

42.2

1.6

3.6

19.0

Hazelnut shell 52.9

5.6

42.7

1.4

1.4

19.3

Hazelnut seedcoat

51.0

5.4

42.3

1.3

1.8

19.3

Softwood

52.1

6.1

41.0

0.2

1.7

20.0

Hardwood

48.6

6.2

41.1

0.4

2.7

18.8

Wheat straw

45.5

5.1

34.1

1.8

13.5

17.0

Wood bark

53.1

6.1

40.6

0.2

1.6

20.5

Waste material

48.3

5.7

45.3

0.7

4.5

17.1

Water hyacinth

39.8

5.0

34.3

1.9

19.0

14.6

Corncob

49.0

5.4

44.6

0.4

1.0

18.4

Corn stover

45.1

6.0

43.1

0.9

4.9

17.4

Brown kelp

28.4

4.1

24.3

4.8

38.4

10.8

Tea waste

48.6

5.5

39.5

0.5

1.4

17.1

Bagasse

45.3

5.1

40.2

0.1

9.3

16.9

Spruce wood

51.9

6.1

40.9

0.3

1.5

20.1

Beech wood

49.5

6.2

41.2

0.4

1.4

19.2

Poplar wood

49.0

6.1

42.8

0.1

1.0

18.8

Ailanthus wood

49.5

6.2

41.0

0.3

1.7

19.0

of world wood products including lumber, plywood, paper and paperboard between the years 1970 and 2005. The availability of fuelwood from forests is continually declining at an ever-increasing rate due to indiscriminate deforestation and slow regeneration, as well as afforestation (Jain and Singh, 1999). The fuelwoods generally used by local people were identified and analyzed quantitatively to select a few species with the best fuelwood characteristics so that plantation on non-agricultural lands could be undertaken (Jain, 1992). Wood biomass involves trees with commercial structure and forest residues not being used in the traditional forest products industries. Available forest residues may appear to be an attractive fuel source. Collection and handling and transport costs are critical factors in the use of forest residues. Although the heat produced from wood wastes is less than that from oil or gas, its cost compared to fossil fuels makes it an attractive source of readily available heat or heat and power. The most

48

2  Fuels from Biomass

effective utilization of wood wastes, particularly in the saw milling and plywood industry, plays an important role in energy efficient production. Table  2.3 shows the sources of available forest and wood manufacturing residues. Wood preparation involves the conversion of roundwood logs into a form suitable for pulping and includes processes for debarking, chipping, screening, handling, and storage. Forest residues typically refer to those parts of trees such as treetops, branches, small-diameter wood, stumps and dead wood as well as undergrowth and low-value species. The conversion of wood to biofuels and biochemicals has long been a goal of the forest products industry. Forest residues alone count for some 50% of the total forest biomass and are currently left in the forest to rot (Demirbas, 2001). Agricultural residues, grasses, algae, kelps, lichens and mosses are also important biomass feedstocks in the world. Algae can grow practically in every place where there is enough sunshine. Some algae can grow in saline water. The most significant difference of algal oil is in the yield and hence its biodiesel yield. According to some estimates, the yield (per acre) of oil from algae is over 200 times the yield from the best-performing plant/vegetable oils (Sheehan et al., 1998). Microal-

Lumber

Plywood

Paper

Paperboard

Million cubic meter

120 100

Fig. 2.2  Use of global wood products: lumber, plywood, paper, and paperboard (1970–2005)

80 60 40 20 0 1965

1975

1985 Year

1995

2005

Table 2.3  Sources of available forest and wood manufacturing residues Source of residue

Type of residue

Forest operations

Branches, bark chips, leaves/needles, stumps, roots, and sawdust

Lumber production

Bark, sawdust, clippings, split wood

Saw milling

Bark, trimmings, split wood, sawdust, planer shavings, sander dust

Plywood production

Bark, sawdust, veneer clippings and wastes, panel trim, sander dust

Paper production

Slab chips, pulping reject, sawdust, clippings

Paperboard production

Bark, sawdust, screening fines, panel trim, sander dust

2.3  The Chemistry of Biomass

49

gae are the fastest growing photosynthesizing organisms. They can complete an entire growing cycle every few days. Approximately 46 tons of oil/hectare/year can be produced from diatom algae. Different algae species produce different amounts of oil. Some algae produce up to 50% oil by weight.

2.3 The Chemistry of Biomass The components of biomass include cellulose, hemicelluloses, lignin, extractives, lipids, proteins, simple sugars, starches, water, hydrocarbons, ash, and other compounds. Two larger carbohydrate categories that have significant value are cellulose and hemicelluloses (holocellulose). The lignin fraction consists of non-sugar type macromolecules. Three structural components are cellulose, hemicelluloses and lignin, which have rough formulae as CH1.67O0.83, CH1.64O0.78, and C10H11O3.5, respectively. The basic structure of all wood and woody biomass consists of cellulose, hemicelluloses, lignin and extractives. Their relative composition is shown in Table 2.4. Softwoods and hardwoods differ greatly in wood structure and composition. Hardwoods contain a greater fraction of vessels and parenchyma cells. Hardwoods have a higher proportion of cellulose, hemicelluloses and extractives than softwoods, but softwoods have a higher proportion of lignin. Hardwoods are denser than softwoods. Cellulose is a remarkable pure organic polymer, consisting solely of units of anhydroglucose held together in a giant straight-chain molecule. These anhydroglucose units are bound together by β-(1,4)-glycosidic linkages. Due to this linkage, cellobiose is established as the repeat unit for cellulose chains. Cellulose must be hydrolyzed to glucose before fermentation to ethanol. By forming intramolecular and intermolecular hydrogen bonds between OH groups within the same cellulose chain and the surrounding cellulose chains, the chains tend to be arranged in parallel and form a crystalline supermolecular structure. Then, bundles of linear cellulose chains (in the longitudinal direction) form a microfibril which is oriented in the cell wall structure. Cellulose is insoluble in most solvents and has a low accessibility to acid and enzymatic hydrolysis (Demirbas, 2008b). Unlike cellulose, hemicelluloses consist of different monosaccharide units. In addition, the polymer chains of hemicelluloses have short branches and are amorphous. Because of the amorphous morphology, hemicelluloses are partially soluble Table 2.4  Structural composition of wood (wt.% of dry and ash-free sample) Wood species

Cellulose

Hemicelluloses

Lignin

Extractives

Hardwood

43–48

27–35

16–24

2–8

Softwood

40–44

24–29

26–33

1–5

50

2  Fuels from Biomass

or swellable in water. Hemicelluloses (arabinoglycuronoxylan and galactoglucomannans) are related to plant gums in composition, and occur in much shorter molecular chains than cellulose. Hemicelluloses are derived mainly from chains of pentose sugars, and act as the cement material holding together the cellulose micelles and fiber (Demirbas, 2008b). Among the most important sugar of the hemicelluloses component is xylose. In hardwood xylan, the backbone chain consists of xylose units which are linked by β-(1,4)-glycosidic bonds and branched by α-(1,2)-glycosidic bonds with 4-O-methylglucuronic acid groups. In addition, O-acetyl groups sometime replace the OH groups in position C2 and C3. For softwood xylan, the acetyl groups are fewer in the backbone chain. However, softwood xylan has additional branches consisting of arabinofuranose units linked by α-(1,3)-glycosidic bonds to the backbone. Hemicelluloses are largely soluble in alkali and, as such, are more easily hydrolyzed (Demirbas, 2008b). Lignins are polymers of aromatic compounds. Their functions are to provide structural strength, provide sealing of the water-conducting system that links roots with leaves, and protect plants against degradation. Lignin is a macromolecule, which consists of alkylphenols and has a complex three-dimensional structure. Lignin is covalently linked with xylans in the case of hardwoods and with galactoglucomannans in softwoods. The basic chemical phenylpropane units of lignin (primarily syringyl, guaiacyl and p-hydroxy phenol) as shown in Fig. 2.3 are bonded together by a set of linkages to form a very complex matrix. This matrix comprises a variety of functional groups, such as hydroxyl, methoxyl and carbonyl, which impart a high polarity to the lignin macromolecule (Demirbas, 2008b). Pyrolysis of lignin, e.g., during combustion, yields a wide range of products, of which the most characteristic ones are methoxy phenols. Of those, the most important are guaiacol and syringol and their derivatives; their presence can be used to trace a smoke source to a wood fire. Lignin biosynthesis begins with the synthesis of monolignols. The starting material is the amino acid phenylalanine. The first reactions in the biosynthesis are shared with the phenylpropanoid pathway, and

OH

OH OCH3

CH3O

OCH3

C

C

C

C

C

C

Guaiacyl

Syringyl

Fig. 2.3  Schematic illustration of building units of lignin

2.3  The Chemistry of Biomass

51

monolignols are considered to be a part of this group of compounds. There are three main types of monolignols: coniferyl alcohol, sinapyl alcohol and paracoumaryl alcohol. Different plants use different monolignols. For example, gymnosperms as Norway spruce have a lignin that consists almost entirely of coniferyl alcohol. Dicotyledonic lignin is a mixture of coniferyl alcohol and sinapyl alcohol (normally more of the latter), and monocotylednic lignin is a mixture of all three monolignols. Some monocotyledons have mostly coniferyl alcohol (as many grasses), while others have mainly sinapyl alcohols, as some palms. Monolignols are synthesized in the cytosol as glucosides. The glucose is added to the monolignol to make them water soluble and to reduce their toxicity. The glucosides are transported through the cell membrane to the apoplast. The glucose is then removed and the monolignols are polymerized into lignin. Four main monolignols in the lignin structure are given in Fig. 2.4. Wood and woody biomass also contain lesser amounts of tannins, simple sugars, starches, pectins and organic soluble extractives. Extractives are the organic substances which have low molecular weight and are soluble in neutral solvents. Extractives include terpenes, tall oil and the fatty acids, esters, and triglycerides, which contribute to paper mill pitch problems. Resin (combination of the following components: terpenes, lignans and other aromatics), fats, waxes, fatty acids and alcohols, terpentines, tannins and flavonoids are categorized as extractives. Biomass has some advantageous chemical properties for use in current energy conversion systems. Compared to other carbon-based fuels, it has low ash content and high reactivity. Biomass combustion is a series of chemical reactions by which carbon is oxidized to carbon dioxide, and hydrogen is oxidized to water. Oxygen deficiency leads to incomplete combustion and the formation of many products of incomplete combustion. Excess air cools the system. The air requirements depend on the chemical and physical characteristics of the fuel. The combustion of the biomass relates to the fuel burn rate, the combustion products, the required excess air for complete combustion, and the fire temperatures. The compositions of biomass among fuel types are considerably varied, especially with respect to inorganic constituents important to the critical problems of fouling and slagging. Alkali and alkaline earth metals, in combination with other fuel elements such as silica and sulfur, and facilitated by the presence of chlorine, are responsible for many undesirable reactions in combustion furnaces and power boilers. CH2OH

OCH3

CH3O

OH OH

OCH3 OH Guaiacol

OH

OCH3

H3CO

Syringol

Coniferyl alcohol

Fig. 2.4  Four main monolignols in the lignin structure

HO OCH3 Sinapyl alcohol

52

2  Fuels from Biomass

2.4 Production of Fuels from Wood Sources Biomass includes 60% wood and 40% non-wood materials. The conversion of wood into biofuels and biochemicals is technically feasible. Wood valorization processes include fractionation, liquefaction, pyrolysis, hydrolysis, fermentation and gasification. Fast pyrolysis utilizes wood biomass to produce a product that is used both as an energy source and a feedstock for chemical production. The bio-oils from wood pyrolysis were composed of a range of cyclopentanone, methoxyphenol, acetic acid, methanol, acetone, furfural, phenol, formic acid, levoglucosan, guaiacol and their alkylated phenol derivatives. When wood is rapidly heated in a reduced oxygen environment, the feeding material does not combust but rather becomes a synthetic gas (syngas), a combination of hydrogen (H2) and carbon monoxide (CO). Wood can be converted by hydrolysis into sugars and subsequently fermentation of sugars. The wood pyrolysis is attractive because forest and industrial wood residues can be readily converted into liquid products. These liquids, as crude bio-oil or slurry of charcoal of water or oil, have advantages in transport, storage, combustion, retrofitting and flexibility in production and marketing (Demirbas, 2007). In the first step of pyrolysis of carbohydrates dehydration occurs and at low temperatures dehydration predominates. Dehydration is also known as a char-forming reaction. Between 550 and 675 K volatile products, tar, and char are formed. The volatile products are CO2, CO, H2O, acetals, furfural, aldehydes and ketones. Levoglucosan is the principle component in tar. Gasification is carried out at high temperatures in order to optimize the gas production. Most wood gasification systems utilize air or oxygen in partial oxidation or combustion processes. The resulting gas, known as producer gas, is a mixture of carbon monoxide, hydrogen and methane, together with carbon dioxide and nitrogen. As mentioned above, when wood is rapidly heated in a reduced oxygen environment, the feeding material becomes a synthetic gas (syngas), a combination of H2 and CO. Syngas can be combusted directly in a boiler or used in a gas turbine to generate electricity. The hydrogen from syngas can be isolated and used to power fuel cells. Syngas has the potential to produce a wide range of commercial fuels and chemicals, including synthetic diesel, methanol and lower carbon alcohols, acetic acid, dimethyl ether, etc. (Demirbas, 2000).

2.5 Production of Fuels from Crops Biofuels such as liquid fuels, bio-oil and biochar, and biogas can be produced from crops. Agriculture-based liquid biofuels include bioethanol, biodiesel, biomethanol, methane, and bio-oil components. Various agricultural residues such as grain dust, crop residues, and fruit tree residues are available as the sources of agricultural energy. Bioenergy from biomass, both residues and energy crops, can be con-

2.5  Production of Fuels from Crops

53

verted into modern energy carriers. Bioethanol is derived from renewable source feedstocks; typically plants such as wheat, sugar beet, corn, straw and wood. Biodiesel is a non-fossil fuel alternative to petrodiesel, which can be obtained from vegetable oil and animal fats by transesterification. Bio-oils are liquid or gaseous fuels made from biomass materials, such as agricultural crops, municipal wastes and agricultural and forestry byproducts via biochemical or thermochemical processes.

2.5.1 Fuels from Cereal Crops Biofuels such as bioethanol and biodiesel originate from cereal crops such as plant oils, and sugar beets. Today the production cost of bioethanol cereal crops is still too high, which is the major reason why bioethanol has not made its breakthrough as a fuel source yet. When producing bioethanol from maize or sugar cane the raw material constitutes about 40–70% of the production cost. Feedstock for bioethanol is essentially comprised of sugar cane and sugar beet. The two are produced in geographically distinct regions. Sugar cane is grown in tropical and subtropical countries, while sugar beet is only grown in temperate climate countries. In European countries, beet molasses are the most utilized sucrose-containing feedstock. Sugar beet crops are grown in most of the EU-25 countries, and yield substantially more ethanol per hectare than wheat. The advantages with sugar beet are a lower cycle of crop production, higher yield, and high tolerance of a wide range of climatic variations, low water and fertilizer requirement. Sweet sorghum is one of the most drought resistant agricultural crops as it has the capability to remain dormant during the driest periods. Another type of feedstock, which can be used for bioethanol production, are starch-based materials. Starch is a biopolymer and is defined as a homopolymer consisting of only one monomer, D-glucose. To produce bioethanol from starch it is necessary to break down the chains of this carbohydrate for obtaining glucose syrup, which can be converted into ethanol by yeasts. The single greatest cost in the production of bioethanol from corn, and the cost with the greatest variability, is the cost of the corn. Figure 2.5 shows the flow chart for the production of bioethanol from cereal grain or straw. Bioethanol can be produced from a large variety of carbohydrates with a general formula of (CH2O)n. Chemical reaction is composed of enzymatic hydrolysis of sucrose followed by fermentation of simple sugars. Fermentation of sucrose is performed using commercial yeast such as Saccharomyces cerevisiae. First, invertase enzyme in the yeast catalyzes the hydrolysis of sucrose to convert it into glucose and fructose. C12H22O11→ C6H12O6 + C6H12O6 Sucrose Glucose Fructose

(2.1)

54

2  Fuels from Biomass

Fig. 2.5  Flow chart for the production bioethanol from cereal grain

CEREAL GRAIN

Course powder flour

Acid hydrolysis, fermentation and distillation

Crude alcohol

Stillage

Dehydration

Drying

BIOETHANOL

Animal feed

Second, zymase, another enzyme also present in the yeast, converts the glucose and the fructose into ethanol. C6H12O6 → 2 C2H5OH + 2CO2

(2.2)

Gluco-amylase enzyme converts the starch into D-glucose. The enzymatic hydrolysis is then followed by fermentation, distillation and dehydration to yield anhydrous bioethanol. Corn (60–70% starch) is the dominant feedstock in the starch-to-bioethanol industry worldwide. Lignocellulosic perennial crops (e.g., short-rotation coppices and grasses) are a promising feedstock because of high yields, low costs, good suitability for lowquality land (which is more easily available for energy crops), and the low environmental impacts.

2.5.2 Fuels from Non-Cereal Crops Agricultural residues such as straws, nut shells, fruit shells, fruit seeds, plant stalks, green leaves and molasses are potential renewable energy resources. A methane digester system, commonly referred to as an anaerobic digester is a device that promotes the decomposition of manure or digestion of the organics in manure to simple organics and gaseous biogas products. Several types of biodigesters have been developed including the floating drum, the fixed dome, the bag, the plastic tube (Beteta, 1995), the plug flow and the up-flow anaerobic sludge blanket digesters. Figure 2.6 shows an on-farm biogas system. The following describes the process of manure and straw mixture digestion. For the first 3 days, the methane yield is almost 0% and carbon dioxide generation is roughly 100%. In this period, digestion occurs as aerobic fermentation to carbon

2.5  Production of Fuels from Crops

55

Manure feeding

Anaerobic digester

Sludge storage

Biogas storage

Nitrogen-rich-manure

Cooking

Heating

Field application

Fig. 2.6  An on-farm biogas system

dioxide. The yields of methane and carbon dioxide gases are then 50-50 on the eleventh day. At the end of the twentieth day, the digestion reaches the stationary phase. The methane content of the biogas is in the range of 73–79% for the runs, the remainder being principally carbon dioxide. During a 30-day digestion period, approximately 80–85% of the biogas is produced in the first 15–18 days. This implies that the digester retention time can be designed to be 15–18 days instead of 30 days. Anaerobic digestion yields of the slurries are given in Table  2.5. Due to the higher proportion of lipids in manure, the methane production is higher than in wheat straw. The total amounts of lipid and protein, in particular, are lower in straw than in manure and thus the theoretical methane yield is significantly lower in wheat straw than in manure (Table 2.5). The average methane yields of manure and wheat straw were 14.7% and 10.4% of volatile solids, respectively (Demirbas and Ozturk, 2004).

Table 2.5  Anaerobic digestion yields of the slurries Run

Inoculated

Manure

Straw

Volatile solids

solution

Biogas

Methane

yield

yield

(ml)

(g)

(g)

(wt.%)

(wt.% of VS)

(wt.% of VS)

1

930

280

   0

89.2

29.8

14.7

2

960

   0

294

81.3

21.6

10.4

3

945

143

144

85.3

26.8

12.9

4

900

  90

180

83.4

24.0

11.9

5

927

185

  93

85.7

27.6

14.2

6

936

  70

210

82.9

23.5

11.5

7

942

214

  72

88.3

28.4

14.0

56

2  Fuels from Biomass

Straw slurry

pH

8

Manure slurry

7

6 0

5

10

15

20

25

30

Time, day Fig. 2.7  The pH values plotted against time for wheat straw and manure slurries

Figure 2.7 shows pH values plotted against time for wheat straw and manure slurries. The pH value of slurry is a sensitive parameter for the digestion rate. During digestion, the volatile fatty acid concentration is lower and the pH higher. The pH of the slurry with manure increased from 6.4 initially, to 6.9–7.0 at the maximum methane production rate. The pH of the slurry with wheat straw was around 7.0–7.1 at the maximum methane production rate. Digester pH increased to its neutral value (6.9–7.1) due to the process stability and the optimal activity of methanogenic bacteria (Demirbas and Ozturk, 2004). When the pyrolysis temperature increased the biochar yield decreased. The biochar yield increased with increasing particle size of the sample. The yield of biooil from pyrolysis of the samples increased with temperature. Anaerobic biogas production is an effective process for conversion of a broad variety of agricultural biomass to methane to substitute natural gas and medium calorific value gases. Pyrolysis of agricultural residues can be used for the production of bio-oil if flash pyrolysis processes are used. Production of this type is currently in the pilot stage (EUREC Agency, 1996). Some problems in the conversion process and use of the oil need to be overcome; these include poor thermal stability and corrosivity of the oil. Upgrading by lowering the oxygen content and removing alkalis by means of hydrogenation and catalytic cracking of the oil may be required for certain applications. Table 2.6 shows the yields of pyrolysis liquid products from hazelnut shell, tea waste, and tobacco stalk samples at different temperatures. As seen in Table 2.6, the yields of liquid products for the samples increased with increasing temperature

Table 2.6  Yields of bio-oil by pyrolysis from agricultural residues at different tempera­ tures (K) Sample

675

725

775

825

875

925

975

1050

Hazelnut shell

38.0

39.5

40.4

41.9

42.2

41.0

39.2

38.5

Tea waste

34.9

35.8

36.0

36.2

38.0

37.0

35.5

33.4

Tobacco stalk

41.0

41.8

43.0

40.2

40.0

40.6

37.3

36.8

2.5  Production of Fuels from Crops

57

from 675 to 875 K and then decreased. The maximum liquid yields from the hazelnut shell, tea waste, tobacco stalk, and yellow pine samples were 42.2%, 38.0%, and 43.0%, respectively (Güllü, 2003).

2.5.3 Fuels from Energy Crops The term “energy crop” can be used both for biomass crops that simply provide high output of biomass per hectare for low inputs, and for those that provide specific products that can be converted into other biofuels such as sugar or starch for bioethanol by fermentation, or into vegetable oil for biodiesel by transesteri­fication. Energy crops such as short-rotation woody crops, herbaceous woody crops, grasses, starch crops, sugar crops, forage crops, oilseed crops, switchgrass, and miscanthus can be converted to liquid biofuels by thermochemical and biochemical conversion processes. Energy crops can be divided into short-rotation energy crops that are harvested on a cycle of anything from 2 to 20 years, depending on the crop and the system, and herbaceous energy crops that are harvested annually. Herbaceous energy crops such as the woody, perennial, rhizomatous grasses like miscanthus offer the advantage of an annual harvest, though typically establishment costs are high. All crops, including some biennial, permanent and multiannual crops, are produced for energy purposes. Energy is generated by burning plants grown for the purpose, often after the dry matter is pelletized. Energy crops are used for firing power plants, either alone or co-fired with other fuels. Alternatively they may be used for heat or combined heat and power (CHP) production. Biogas plants can be directly supplemented with energy crops. European production of biodiesel from energy crops has grown steadily in the last decade, principally focused on rapeseed used for oil and energy. In the United States, biodiesel is being made from soybean oil because more soybean oil is produced than all other sources of fats and oil combined. There are many candidates for feedstocks, including recycled cooking oils, animal fats, and a variety of other oilseed crops. The European Union accounted for nearly 89% of all biodiesel production worldwide in 2005. By 2010, the United States is expected to become the world’s largest single biodiesel market, accounting for roughly 18% of world biodiesel consumption, followed by Germany. Switchgrass is a perennial grass native to North America. Switchgrass makes for a great energy crop because it grows fast, capturing lots of solar energy and turning it into chemical energy, which is stored as cellulose. Switchgrass reaches its full yield potential after the third year planted, producing approximately 6 to 8 tons per acre; that is 500 gallons of ethanol per acre. Miscanthus is a tall perennial grass that has been evaluated in Europe during the past 5 to 10 years as a new bioenergy crop. Like other energy crops, the harvested stems of miscanthus may be used as fuel for production of heat and electric power, or for conversion to other useful products such as ethanol.

58

2  Fuels from Biomass

Sweet sorghum can be considered as an energy crop, because it can be grown in all continents, in tropical, subtropical, temperate regions as well as in poor quality soils. Sweet sorghum is a warm-season crop that matures earlier under high temperatures and short days. Sweet sorghum is an extraordinarily promising multifunctional crop not only for its high economic value but also for its capacity to provide a very wide range of renewable energy products, industrial commodities, food and animal feed products. Sweet sorghum biomass is rich in readily fermentable sugars and thus it can be considered an excellent raw material for fermentative hydrogen production. Integrated production of several crops (sweet sorghum/ sugar cane/sweet sorghum corn/sweet potatoes, etc.) and simultaneous processing of the full crop components (starch, sugar, lignocellulosic) can improve the global economics of bioenergy schemes considerably in view of a viable production of bioethanol.

Summary Biomass refers to the non-fossilized and biodegradable organic material that originates from plants, animals and microorganisms. Biomass is the world’s fourth largest energy source, following coal, oil and natural gas. Biomass appears to be an attractive feedstock for three main reasons. First, it is a renewable resource that could be sustainably developed in the future. Second, it appears to have positive environmental properties, for example, reducing greenhouse gas emissions, possibly reducing NOx and SOx depending on the fossil fuels displaced. Third, it appears to have significant economic potential provided that fossil fuel prices increase in the future. The components of biomass include cellulose, hemicelluloses, lignin, extractives, lipids, proteins, simple sugars, starches, water, hydrocarbons, ash, and other compounds. Two larger carbohydrate categories that have significant value are cellulose and hemicelluloses (holocellulose). The lignin fraction consists of non-sugar type macromolecules. Three structural components are cellulose, hemicelluloses and lignin, which have rough formulae as CH1.67O0.83, CH1.64O0.78, and C10H11O3.5, respectively. Biomass includes 60% wood and 40% non-wood materials. The conversion of wood into biofuels and biochemicals is technically feasible. Wood valorization processes include fractionation, liquefaction, pyrolysis, hydrolysis, fermentation and gasification.

References Beteta, T. 1995. Experiences with plastic tube biodigesters in Colombia. Universidad Nacional Agraria, Managua, Nicaragua. Demirbas, A. 2000. Recent advances in biomass conversion technologies. Energy Edu Sci Technol 6:19–41.

References 

59

Demirbas, A. 2001. Biomass resource facilities and biomass conversion processing for fuel and chemicals. Energy Convers Manage 42:1357–1378. Demirbas, A. 2003. Fuelwood characteristics of six indigenous wood species from Eastern Black Sea Region. Energy Sources 25:309–316. Demirbas, A. 2004. Combustion characteristics of different biomass fuels. Prog Energy Combus Sci 30:219–230. Demirbas, A. 2007. The influence of temperature on the yields of compounds existing in bio-oils obtained from biomass samples via pyrolysis. Fuel Proc Technol 88:591–598. Demirbas, A. 2008a. Biodiesel: A realistic fuel alternative for diesel engines. Springer, London. Demirbas, A. 2008b. Heavy metal adsorption onto agro-based waste materials: a review. J Hazard Mat 157:220–229. Demirbas, A., Ozturk, T. 2004. Anaerobic digestion of agricultural solid residues. Int J Green Energy 1:483–494. EUREC Agency. 1996. The future for renewable energy, prospects and directions. James and James Science, London. Güllü, D. 2003. Effect of catalyst on yield of liquid products from biomass via pyrolysis. Energy Sources 25:753–765. Jain, R.K. 1992. Fuelwood characteristics of certain hardwood and softwood tree species of India Biores Technol 41:129–133. Jain, R.K., Singh, B. 1999. Fuelwood characteristics of selected indigenous tree species from central India. Biores Technol 68:305–308. Sheehan, J., Dunahay, T., Benemann, J., Roessler, P. 1998. A look back at the US Department of Energy’s Aquatic Species Program: biodiesel from algae. National Renewable Energy Laboratory (NREL) Report: NREL/TP-580-24190, Golden, Colorado.

Chapter 3

Biofuels

3.1 Introduction The term biofuel refers to liquid, gas and solid fuels predominantly produced from biomass. Biofuels are important as they affect a wide array of topics, including energy security, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sector. Biofuels include bioethanol, biomethanol, vegetable oils, biodiesel, biogas, biosynthetic gas (biosyngas), bio-oil, biochar, Fischer–Tropsch liquids, and biohydrogen. There are two global biomass-based liquid transportation fuels that might replace gasoline and diesel fuel. These are bioethanol and biodiesel. World production of biofuel was about 68 billion liters in 2007. The primary feedstocks of bioethanol are sugarcane and corn. Bioethanol is a gasoline additive/substitute. Bioethanol is by far the most widely used biofuel for transportation worldwide. About 60% of global bioethanol production comes from sugarcane and 40% from other crops. Biodiesel refers to a diesel-equivalent mono-alkyl ester-based oxygenated fuel. Biodiesel production using inedible vegetable oil, waste oil and grease has become more attractive recently. The economic performance of a biodiesel plant can be determined once certain factors are identified, such as plant capacity, process technology, raw material cost and chemical costs. The central policy of biofuel concerns job creation, greater efficiency in the general business environment, and protection of the environment. Biofuels offer a number of technical and environmental benefits over conventional fossil fuels, which make them attractive as alternatives for the transport sector. The benefits include greenhouse gas reductions including reduced carbon dioxide emissions, which will contribute to domestic and international targets, the diversification of the fuel sector, biodegradability, sustainability, and an additional market for agricultural products. Biofuels help to protect and create jobs. Table 3.1 shows the major benefits of biofuels.

A. Demirbas, Biohydrogen, © Springer 2009

61

62

3  Biofuels

Table 3.1  Major benefits of biofuels Economic impacts

Sustainability Fuel diversity Increased number of rural manufacturing jobs Increased income taxes Increased investments in plant and equipment Agricultural development International Reducing the dependency on imported petroleum

Environmental impacts

Greenhouse gas reductions Reducing of air pollution Biodegradability Higher combustion efficiency Improved land and water use Carbon sequestration

Energy security

Domestic targets Supply reliability Reducing use of fossil fuels Ready availability Domestic distribution Renewability

According to a study by the European Commission, European production of biofuels equivalent to 1% of EU automotive fuel consumption would help to protect and/or create between 45 000 and 75 000 jobs. Biofuels can be used as an alternative fuel for transport, as can other alternatives such as liquid natural gas (LNG), compressed natural gas (CNG) and liquefied petroleum gas (LPG). In the longer term, significant use of biofuels could offer large carbon savings. Policy drivers for renewable liquid biofuels have attracted particularly high levels of assistance in some countries given their promise of benefits in several areas of interest to governments, including agricultural production, greenhouse gas emissions, energy security, trade balances, rural development and economic opportunities for developing countries (Demirbas, 2008a). First generation biofuels refer to biofuels made from sugar, starch, vegetable oils, or animal fats using conventional technology. The basic feedstocks for the production of first generation biofuels are often seeds or grains such as wheat, which yields starch that is fermented into bioethanol, or sunflower seeds, which are pressed to yield vegetable oil that can be used in biodiesel. Table 3.2 shows the classification of renewable biofuels based on their production technologies.

3.1  Introduction

63

Table 3.2  Classification of renewable biofuels based on their production technologies Generation

Feedstock

Example

First generation biofuels

Sugar, starch, vegetable oils, or animal fats

Bioalcohols, vegetable oil, Biodiesel, biosyngas, biogas

Second generation biofuels

Non-food crops, wheat straw, corn, Bioalcohols, bio-oil, wood, solid waste, energy crop bio-DMF, Biohydrogen, bio-Fischer–Tropsch diesel, wood diesel

Third generation biofuels

Algae

Vegetable oil, biodiesel

Fourth generation biofuels

Vegetable oil, biodiesel

Biogasoline

Total world production, billion liters

60 50 40

Ethanol Biodiesel

30 20 10 0 1979

1984 1989 1994 Year

1999 2004

Fig. 3.1  World production of ethanol and biodiesel, 1980–2007

Second and third generation biofuels are also called advanced biofuels. Second generation biofuels made from non-food crops, wheat straw, corn, wood, energy crop using advanced technology. Algae fuel, also called oilgae or third generation biofuel, is a biofuel from algae. Algae are low-input/high-yield (30 times more energy per acre than land) feedstocks to produce biofuels using more advanced technology. On the other hand, an appearing fourth generation is based in the conversion of vegoil and biodiesel into biogasoline using the most advanced technology. Figure 3.1 shows the world productions of ethanol and biodiesel between 1980 and 2007 (Demirbas, 2008a). Between 1991 and 2001, world ethanol production rose from around 16 billion liters a year to 18.5 billion liters. From 2001 to 2007, production is expected to have tripled, to almost 60 billion liters a year. Brazil was the world’s leading ethanol producer until 2005 when U.S. production roughly

64

3  Biofuels

5 4.5 4 Billion gallon

3.5 3 2.5 2 1.5 1 0.5 0

USA

Brazil

China

India

France

Fig. 3.2  The top five bioethanol producers (billion gallons) in 2006

equaled Brazil’s. The United States became the world’s leading ethanol producer in 2006. China holds a distant but important third place in world rankings, followed by India, France, Germany and Spain. Figure 3.2 shows the top five bioethanol producers in 2006 (RFA, 2007).

3.2 Bioethanol Nowadays ethanol is the most popular fuel. Bioethanol is ethyl alcohol, grain alcohol, or chemically C2H5OH or EtOH. The use of ethanol as a motor fuel has as long a history as the car itself. Ethanol can be produced from cellulose feedstocks such as corn stalks, rice straw, sugar cane bagasse, pulpwood, switchgrass, and municipal solid waste is called bioethanol. Bioethanol is a renewable green fuel. Bioethanol is produced by fermentation of sugars, which can be obtained from natural sugars (e.g., sugar cane, sugar beet), starches (e.g., corn, wheat), or cellulosic biomass (e.g., corn stover, straw, grass, wood). The most common feedstock is sugar cane or sugar beet, and the second common feedstock is corn starch. Currently, cellulosic biomass use is very limited due to the expensive pretreatment required for breaking the crystalline structure of cellulose. Bioethanol is already an established commodity due to its ongoing non-fuel uses in beverages, and in the manufacture of pharmaceuticals and cosmetics. In fact, ethanol is the oldest synthetic organic chemical used by mankind. Table 3.3 shows ethanol production in different continents (Demirbas, 2008b). Bioethanol can be used as a 10% blend with gasoline without need for any engine modification. However, with some engine modification, bioethanol can be used at higher levels, for example, E85 (85% bioethanol).

3.3  Other Bioalcohols

65

Table 3.3  Ethanol production in different continents (billion liters/year) in 2006 America

Asia

Europe

Africa

Oceania

22.3

5.7

4.6

0.5

0.2

Bioethanol currently accounts for more than 94% of global biofuel production, with the majority coming from sugarcane. About 60% of global bioethanol production comes from sugarcane and 40% from other crops. Brazil and the United States are the world leaders, which together accounted for about 70% of the world bioethanol production exploiting sugarcane and corn respectively. Ethanol has been used in Germany and France as early as 1894 by the then incipient industry of internal combustion engines. Brazil has utilized ethanol as a fuel since 1925. Currently, ethanol is produced from sugar beets and from molasses. A typical yield is 72.5 l of ethanol per ton of sugar cane. Modern crops yield 60 tons of sugar cane per hectare of land. Production of ethanol from biomass is one way to reduce both the consumption of crude oil and environmental pollution. The use of gasohol (an ethanol and gasoline mixture) as an alternative motor fuel has been steadily increasing in the world for a number of reasons. Domestic production and use of ethanol for fuel can decrease dependence on foreign oil, reduce trade deficits, create jobs in rural areas, reduce air pollution, and reduce global climate change carbon dioxide build-up (Bala, 2005). Bioethanol can be produced from a large variety of carbohydrates with a general formula of (CH2O)n. Fermentation of sucrose is performed using commercial yeast such as Saccharomyces cerevisiae. The chemical reaction is composed of enzymatic hydrolysis of sucrose followed by fermentation of simple sugars (Baltz et al., 1982; Sokhansanj et al., 2002; Kim and Dale, 2005). First, invertase enzyme in the yeast catalyzes the hydrolysis of sucrose to convert it into glucose and fructose. Second, zymase, another enzyme also present in the yeast, converts the glucose and the fructose into ethanol. A major processing step in an ethanol plant is enzymatic saccharification of cellulose to sugars through treatment by enzymes; this step requires lengthy processing and normally follows a short-term pre-treatment step (Kumar et al., 2005).

3.3 Other Bioalcohols The alcohols that can be used for motor fuels are methanol (CH3OH), ethanol (C2H5OH), propanol (C3H7OH), and butanol (C4H9OH). However only the first two of the alcohols are technically and economically suitable as fuels for internal combustion engines (ICEs). Main commercial bioalcohols from renewable feedstocks are bioethanol and biomethanol in the world’s energy market. Methanol is known as “wood alcohol.” Generally, methanol is easier to find than ethanol. Sustainable methods of methanol production are currently not economi-

66

3  Biofuels

cally viable. Methanol is produced from synthetic gas or biogas and evaluated as a fuel for internal combustion engines. The production of methanol is a cost-intensive chemical process. Methanol is another possible replacement for conventional motor fuels. In fact, it has been considered as a possible large-volume motor fuel substitute at various times during gasoline shortages. In fact, it was often used in the early twentieth century to power automobiles before introduction of inexpensive gasoline. Later, synthetically produced methanol was widely used as a motor fuel in Germany during World War II. Again, during the oil crisis of 1970s, methanol blending with motor fuel received attention due to its availability and low cost. Methanol is poisonous and burns with an invisible flame. Similar to ethanol, methanol has a high octane rating and hence is suitable for the Otto engine. Today, methanol is commonly used in biodiesel production for its reactivity with vegetable oils. Methanol can be used as one possible replacement for conventional motor fuels. Many tests have shown promising results using 85–100% by volume methanol as a transportation fuel in automobiles, trucks and buses. Before 1920s, methanol was obtained from wood as a co-product of charcoal production, hence the name wood alcohol. Methanol is currently manufactured worldwide from syngas, which is derived from natural gas, refinery off-gas, coal or petroleum, as: 2H2 + CO → CH3OH

(3.1)

The above reaction can be carried out in the presence of a variety of catalysts including Ni, Cu/Zn, Cu/SiO2, Pd/SiO2, and Pd/ZnO. In the case of coal, it is first pulverized and cleaned, then fed to a gasifier bed where it is reacted with oxygen and steam to produce the syngas. A 2:1 mole ratio of hydrogen to carbon monoxide is fed to a fixed-catalyst bed reactor for methanol production. Also, the technology for making methanol from natural gas is already in place and in wide use. Current natural gas feedstocks are so inexpensive that even with tax incentives renewable methanol has not been able to compete economically. The composition of biosyngas from biomass is shown in Table 3.4. The hydrogen to CO ratio in biosyngas is less than that from coal or natural gas, hence additional hydrogen is needed for full conversion to methanol. The gases produced from biomass can be steam reformed to produce hydrogen and followed by water–gas shift reaction to further enhance the hydrogen content. Wet biomass can be easily Table 3.4  Composition of biosyngas from biomass gasification Constituents

Percentage by volume (dry and nitrogen-free)

Carbon monoxide (CO)

28–36

Hydrogen (H2)

22–32

Carbon dioxide (CO2)

21–30

Methane (CH4)

  8–11

Ethene (C2H4)

  2–4

3.4  Biorefinery

67

Table 3.5  Main production facilities of methanol and biomethanol Methanol

Biomethanol

Catalytic synthesis from CO and H2

Catalytic synthesis from CO and H2

Natural gas

Distillation of liquid from wood pyrolysis

Petroleum gas

Gaseous products from biomass gasification

Distillation of liquid from coal pyrolysis

Synthetic gas from biomass and coal

gasified using supercritical water conditions. Main production pathways for methanol and biomethanol are compared in Table 3.5. Methanol can be produced from biomass, essentially any primary energy source. Thus, the choice of fuel in the transportation sector is to some extent determined by the availability of biomass. As regards to the difference between hydrogen and methanol production costs, conversion of natural gas, biomass and coal into hydrogen is generally more energy efficient and less expensive than the conversion into methanol.

3.4 Biorefinery A biorefinery is a facility that integrates biomass conversion processes and equipment to produce fuels, power, and value-added chemicals from biomass. Biorefinery is the co-production of a spectrum of bio-based products and energy from biomass. The biorefinery concept is analogous to today’s crude oil refinery. Biorefinery is a relatively new term referring to the conversion of biomass feedstock into a host of valuable chemicals and energy with minimal waste and emissions. Biorefinery includes fractionation for separation of primary refinery products. The fractionation refers to the conversion of wood into its constituent components (cellulose, hemicelluloses and lignin). Processes include steam explosion, aqueous separation and hot water systems. Commercial products of biomass fractionation include levulinic acid, xylitol and alcohols. Figure 3.3 shows the fractionation of wood and chemicals from wood. Main fractionation chemicals from wood ingredients are: 1. Dissociation of cell components → Lignin fragment + Oligosaccharides + Cellulose 2. Hydrolysis of cellulose (saccharification) → Glucose 3. Conversion of glucose (fermentation) → Ethanol + Lactic acid 4. Chemical degradation of cellulose → Levulinic acid + Xylitol 5. Chemical degradation of lignin → Phenolic products Biorefinery is the process of extracting valuable chemicals and polymers from biomass. The main technologies to produce chemicals from biomass are: (a) biomass refining or pre-treatment, (b) thermochemical conversion (gasification, pyrolysis,

68

3  Biofuels Hardwood

Crushing

Steam explosion

Warm water washing

Aqueous phase (Hemicelluloses)

Solid phases (Cellulose + Lignin)

Enzymatic fermentation

Concentrated sulfuric acid extraction

Ethanol

Aqueous phase (Cellulose hydrolysis products)

Solid phase (Lignin)

Enzymatic fermentation

NaOH liquefaction

Ethanol

Polymerization

Adhesive

Fig. 3.3  Fractionation of wood and chemicals from wood

hydrothermal upgrading), (c) fermentation and bioconversion, and (d) product separation and upgrading. There are four main biorefineries: biosyngas-based refinery, pyrolysis-based refinery, hydrothermal upgrading-based refinery, and fermentation-based refinery. Biosyngas is a multifunctional intermediate for the production of materials, chemicals, transportation fuels, power and/or heat from biomass. Figure 3.4 shows the gasification-based thermochemical biorefinery. Pyrolysis oil (bio-oil) is produced in fast and flash pyrolysis processes and can be used for indirect co-firing for power production in conventional power plants and potentially as a high energy density intermediate for the final production of chemicals and/or transportation fuels. Gas chromatographic analysis of the liquid fraction of pyrolysis products from beech wood is given in Table 3.6 (Demirbas, 2007). Biocrude results from severe hydrothermal upgrading (HTU) of relatively wet biomass and potentially can be used for the production of materials, chemicals,

3.4  Biorefinery

69

Biomass

Electricity and Heat

CO2 removal

Cryongenic distillation

Gasification

Biosyngas

Transportation fuels -Fischer–Tropsch diesel -Hydrogen -Methane

Gaseous fuels -Methane -SNG

Torrefaction

Products -Hydrogen -Carbon monoxide -Carbon dioxide -Methane -Acetylene -Ethylene -Benzene, toluene, xylene -Light tars -Heavy tars -Ammonia -Water

Chemicals -Solvents -Acids

Tar distillation

Heavy tars

Light tars

Solvents

Fertilizer

Fig. 3.4  Gasification-based thermochemical biorefinery

transportation fuels, power and/or heat. Mixed sugars resulting from fermentation (C5 and C6 sugars) are further refined substrates for chemical and bioconversion. The bio-oil formed at 725 K contains high concentrations of compounds such as acetic acid, 1-hydroxy-2-butanone, 1-hydroxy-2-propanone, methanol, 2,6-dimethoxyphenol, 4-methyl-2,6-dimetoxyphenol and 2-Cyclopenten-1-one, etc. A significant characteristic of bio-oils was the high percentage of alkylated compounds especially methyl derivatives. The structural components of the biomass samples mainly have an effect on pyrolytic degradation products. A reaction mechanism is proposed which describes a possible reaction route for the formation of the characteristic compounds found in the oils. The supercritical water extraction and liquefaction partial reactions also occur during the pyrolysis. The phenol content increased to 52% and the yield of neutral oils increased from 18 to 33% with increasing temperature, while the methoxyl content decreased. The methoxyl content at 675 K amounted to 11.8%, at 875 K to only 5%. The coke formed could be briquetted without the addition of a binder. It has been reported that the first runs in the pyrolysis of the pyroligneous acid consists of about 50% methanol, 18% acetone, 7% esters, 6% aldehydes, 0.5% ethyl alcohol, 18.5% water, and small amounts of furfural (Demirbas, 2007).

70

3  Biofuels

Table 3.6  Gas chromatographic analysis of the liquid fraction of pyrolysis products from beech wood (wt.% dry basis) Compound

Reaction temperature (K) 625

675

725

775

825

875

Acetic acid

16.8

16.5

15.9

12.6

8.42

5.30

Methyl acetate

0.47

0.35

0.21

0.16

0.14

0.11

1-Hydroxy-2-propanone

6.32

6.84

7.26

7.66

8.21

8.46

Methanol

4.16

4.63

5.08

5.34

5.63

5.82

1-Hydroxy-2-butanone

3.40

3.62

3.82

3.88

3.96

4.11

1-Hydroxy-2-propane acetate

1.06

0.97

0.88

0.83

0.78

0.75

Levoglucosan

2.59

2.10

1.62

1.30

1.09

0.38

1-Hydroxy-2-butanone acetate

0.97

0.78

0.62

0.54

0.48

0.45

Formic acid

1.18

1.04

0.84

0.72

0.60

0.48

Guaiacol

0.74

0.78

0.82

0.86

0.89

0.93

Crotonic acid

0.96

0.74

0.62

0.41

0.30

0.18

Butyrolactone

0.74

0.68

0.66

0.67

0.62

0.63

Propionic acid

0.96

0.81

0.60

0.49

0.41

0.34

Acetone

0.62

0.78

0.93

1.08

1.22

1.28

2,3-Butanedione

0.46

0.50

0.56

0.56

0.58

0.61

2,3-Pentanedione

0.34

0.42

0.50

0.53

0.59

0.64

Valeric acid

0.72

0.62

0.55

0.46

0.38

0.30

Isovaleric acid

0.68

0.59

0.51

0.42

0.35

0.26

Furfural

2.52

2.26

2.09

1.84

1.72

1.58

5-Methyl-furfural

0.65

0.51

0.42

0.44

0.40

0.36

Butyric acid

0.56

0.50

0.46

0.39

0.31

0.23

Isobutyric acid

0.49

0.44

0.38

0.30

0.25

0.18

Valerolactone

0.51

0.45

0.38

0.32

0.34

0.35

Propanone

0.41

0.35

0.28

0.25

0.26

0.21

2-Butanone

0.18

0.17

0.32

0.38

0.45

0.43

Crotonolactone

0.12

0.19

0.29

0.36

0.40

0.44

Acrylic acid

0.44

0.39

0.33

0.25

0.19

0.15

2-Cyclopenten-1-one

1.48

1.65

1.86

1.96

2.05

2.13

2-Methyl-2-cyclopenten-1-one

0.40

0.31

0.24

0.17

0.13

0.14

2-Methyl-cyclopentenone

0.20

0.18

0.17

0.22

0.25

0.29

Cyclopentenone

0.10

0.14

0.16

0.23

0.27

0.31

Methyl-2-furancarboxaldehyde

0.73

0.65

0.58

0.50

0.44

0.38

Phenol

0.24

0.30

0.36

0.43

0.54

0.66

2,6-Dimethoxyphenol

2.28

2.09

1.98

1.88

1.81

1.76

3.5  Biodiesel

71

Table 3.6  (continued) Compound

Reaction temperature (K) 625

675

725

775

825

875

Dimethyl phenol

0.08

0.13

0.18

0.42

0.64

0.90

Methyl phenol

0.32

0.38

0.44

0.50

0.66

0.87

4-Methyl-2,6-dimetoxyphenol

2.24

2.05

1.84

1.74

1.69

1.58

3.5 Biodiesel Fossil fuel resources are decreasing daily. Biodiesel is attracting increasing attention worldwide as blending components or direct replacements for diesel fuel in vehicle engines. Biodiesel typically comprises lower alkyl fatty acid (chain length C14–C22), esters of short-chain alcohols, primarily, methanol or ethanol. Various methods have been reported for the production of biodiesel from vegetable oil, such as direct use and blending, microemulsification, pyrolysis, and transesterification. Among these, transesterification is an attractive and widely accepted technique. The purpose of the transesterification process is to lower the viscosity of the oil. The most important variables affecting methyl ester yield during the transesterification reaction are the molar ratio of alcohol to vegetable oil and the reaction temperature. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages over other new renewable and clean engine fuel alternatives. The interest in fatty acid methyl esters based on biodiesel has grown considerably worldwide. A rapid expansion in production is being observed not only in the United States but also in many other developed and developing countries around the world. Increasing the share of biodiesel in transportation fuels may decrease the net emission of CO2 and alleviate the global warming problem. Biodiesel fuel is a renewable substitute fuel for petroleum diesel or petrodiesel fuel made from vegetable or animal fats; it can be used in any mixture with petrodiesel fuel, as it has very similar characteristics, but it has lower exhaust emissions. Biodiesel fuel has better properties than petrodiesel fuel; it is renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. Biodiesel seems to be a realistic fuel for the future, and has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification. Typical raw materials of biodiesel are rapeseed oil, soybean oil, sunflower oil and palm oil. Beef and sheep tallow and poultry oil from animal sources and cooking oil are also sources of raw materials. There are various other biodiesel sources: almond, andiroba (Carapa guianensis), babassu (Orbignia sp.), barley, camelina (Camelina sativa), coconut, copra, cumaru (Dipteryx odorata), Cynara cardunculus, fish oil, groundnut, Jatropha curcas, karanja (Pongamia glabra), laurel, Lesquerella fendleri, Madhuca indica, microalgae (Chlorella vulgaris), oat, piqui (Caryocar sp.), poppy seed, rice, rubber seed, sesame, sorghum, tobacco seed, and wheat (Pinto et al., 2005).

72

3  Biofuels

The biggest advantage of biodiesel is the environmentally friendliness that it has over gasoline and petroleum diesel. The advantages of biodiesel as a diesel fuel are its portability, ready availability, renewability, higher combustion efficiency, lower sulfur and aromatic content, higher cetane number, and higher biodegradability (Ma and Hanna, 1999). The main advantages of biodiesel given in the literature include its domestic origin, its potential for reducing a given economy’s dependency on imported petroleum, biodegradability, high flash point, and inherent lubricity in the neat form. Biodiesel can be made from domestically produced, renewable oilseed crops such as soybean, rapeseed, and sunflower. The risks of handling, transporting, and storing biodiesel are much lower than those associated with petrodiesel. Biodiesel is the only alternative fuel in which low-concentration biodiesel–diesel blends run on conventional unmodified engines. It can be stored anywhere that petroleum diesel fuel is stored. Biodiesel is safe to handle and transport because it is as biodegradable as sugar and has a high flash point compared to petroleum diesel fuel. Biodiesel can be used alone or mixed in any ratio with petroleum diesel fuel. The most common blend is a mix of 20% biodiesel with 80% petroleum diesel, or B20 in recent scientific investigations; however, in Europe the current regulation foresees a maximum 5.75% of biodiesel. The commercial biodiesel fuel significantly reduced PM exhaust emissions (75–83%) compared to the petrodiesel base fuel. However, NOx exhaust emissions increased slightly with commercial biodiesel compared to the base fuel. The chain length of the compounds had little effect on NOx and PM exhaust emissions, while the influence was greater on HC and CO, the latter being reduced with decreasing chain length. Non-saturation in the fatty compounds causes an increase in NOx exhaust emissions. Many studies on the performances and emissions of compression ignition engines, fueled with pure biodiesel and blends with diesel fuel, have been conducted and are reported in the literature (Laforgia and Ardito, 1994). Fuel characterization data show some similarities and differences between biodiesel and petrodiesel fuels. The sulfur content of petrodiesel is 20 to 50 times that of biodiesel. Biodiesel has demonstrated a number of promising characteristics, including reduction of exhaust emissions. For soybean-based biodiesel at this concentration, the estimated emission impacts for percent change in emissions of NOx, particular matter (PM), HC, and CO were +20%, –10.1%, –21.1%, and –11.0%, respectively (EPA, 2002). The use of blends of biodiesel and diesel oil are preferred in engines in order to avoid some problems related to the decrease of power and torque, and to the increase of NOx emissions (a contributing factor in the localized formation of smog and ozone) that occurs with an increase in the content of pure biodiesel in a blend. Emissions of all pollutants except NOx appear to decrease when biodiesel is used. The use of biodiesel in a conventional diesel engine dramatically reduces the emissions of unburned hydrocarbons, carbon dioxide, carbon monoxide, sulfates, polycyclic aromatic hydrocarbons, nitrated polycyclic aromatic hydrocarbons, ozone-forming hydrocarbons, and particulate matter. The net contribution of carbon dioxide from biomass combustion is small.

3.5  Biodiesel

73

Biodegradability of biodiesel has been proposed as a solution for the waste problem. Biodegradable fuels such as biodiesels have an expanding range of potential applications and they are environmentally friendly. Therefore, there is growing interest in degradable diesel fuels that degrade more rapidly than conventional disposable fuels. Biodiesel is non-toxic and degrades about four times faster than petrodiesel. Its oxygen content improves the biodegradation process, leading to a decreased level of quick biodegradation. About 90 to 98% of biodiesel is mineralized in 21 to 28 days under aerobic as well as anaerobic conditions. The biodegradabilities of several biodiesels in the aquatic environment show that all biodiesel fuels are readily biodegradable. In one study, after 28 days all biodiesel fuels were 77 to 89% biodegraded; diesel fuel was only 18% biodegraded. The enzymes responsible for the dehydrogenation/oxidation reactions that occur in the process of degradation recognize oxygen atoms and attack them immediately. Biodiesel methyl esters improve the lubrication properties of the diesel fuel blend. Fuel injectors and some types of fuel pumps rely on fuel for lubrication. Biodiesel reduced long-term engine wear in test diesel engines to less than half of what was observed in engines running on current low-sulfur diesel fuel. Lubricity properties of fuel are important for reducing friction wear in engine components normally lubricated by the fuel rather than crankcase oil (Ma and Hanna, 1999; Demirbas, 2003). Biodiesel provides significant lubricity improvement over petroleum diesel fuel. Lubricity results of biodiesel and petroleum diesel using industry test methods indicate that there is a marked improvement in lubricity when biodiesel is added to conventional diesel fuel. Even biodiesel levels below 1% can provide up to a 30% increase in lubricity. Lubricity results of biodiesel and petroleum diesel using industry test methods indicate that there is a marked improvement in lubricity when biodiesel is added to conventional diesel fuel. Biodiesels are mono-alkyl esters containing approximately 10% oxygen by weight. The oxygen improves the efficiency of combustion, but it takes up space in the blend and therefore slightly increases the apparent fuel consumption rate observed while operating an engine with biodiesel. The high combustion temperature at high engine speed becomes the dominant factor, making both heated and unheated fuel to acquire the same temperature before fuel injection. Brake thermal efficiency is better in the dual fuel operation and with the methyl ester of vegetable oil as compared to the blend. In an earlier study (Canakci et al., 2006), the tests were performed with commercial diesel fuel and biodiesel. The maximum brake power values of biodiesel and diesel were 4.390 and 5.208 kW obtained at 2750 and 2500 rpm, respectively. According to these values, the commercial diesel fuel has the greatest brake power. The major disadvantages of biodiesel are its higher viscosity, lower energy content, higher cloud point and pour point, higher nitrogen oxide (NOx) emissions, lower engine speed and power, injector coking, engine compatibility, and high price (Demirbas, 2008c). The biodiesels on the average decrease power by 5% compared to that of diesel at the rated load. The maximum torque values are about 21.0 Nm at 1500 rpm for the diesel fuel, and 19.7 Nm at 1500 rpm for the biodiesel. The torque values of commercial diesel fuel are greater than those of biodiesel. Peak torque

74

3  Biofuels

applies less to biodiesel fuels than it does to No. 2 diesel fuel but occurs at lower engine speed and generally its torque curves are flatter. The specific fuel consumption values of biodiesel are greater than those of commercial diesel fuel. The effective efficiency and effective pressure values of commercial diesel fuel are greater than those of biodiesel (Canakci et al., 2006). Important operating disadvantages of biodiesel in comparison with petrodiesel are cold-start problems, the lower energy content, higher copper strip corrosion and fuel pumping difficulty from higher viscosity. Fuel consumption at full load condition and low speeds generally is high. Fuel consumption first decreases and then increases with increasing speed. The reason is that, the produced power in low speeds is low and the main part of fuel is consumed to overcome the engine friction. The effects of oxidative degradation caused by contact with ambient air (autoxidation) during long-term storage present a legitimate concern in terms of maintaining the fuel quality of biodiesel. Transunsaturated fatty acids, or transfats, are solid fats produced artificially by heating liquid vegetable oils in the presence of metal catalysts and hydrogen. This process, partial hydrogenation, causes carbon atoms to bond in a straight configuration and remain in a solid state at room temperature. Physical properties that are sensitive to the effects of fatty oil oxidation include viscosity, refractive index, and dielectric constant. In oxidative instability, the methylene group (-CH2-) carbons between the olefinic carbons are the sites of first attack. Oxidation to CO2 of biodiesel results in the formation of hydroperoxides. The formation of a hydroperoxide follows a well-known peroxidation chain mechanism. Oxidative lipid modifications occur through lipid peroxidation mechanisms in which free radicals and reactive oxygen species abstract a methylene hydrogen atom from polyunsaturated fatty acids, producing a carbon-centered lipid radical. Spontaneous rearrangement of the 1,4-pentadiene yields a conjugated diene, which reacts with molecular oxygen to form a lipid peroxyl radical.

3.6 Biogas Biogas is an environment friendly, clean, cheap and versatile gaseous fuel. It is mainly a mixture of methane and carbon dioxide obtained by anaerobic digestion of biomass, sewage sludge, animal wastes, and industrial effluents. Anaerobic digestion occurs in the absence of air and is typically carried out for a few weeks. Typical compositions of biogas and landfill gas are given in Table 3.7. CH4 and CO2 make up around 90% of the gas volume produced, both of which are greenhouse gases. However, CO2 is recycled back by the plants, but methane can contribute to global warming. Hence, the capture and fuel use of biogas is beneficial in two ways: (a) fuel value, and (b) conversion of CH4 into CO2, a plant-recyclable carbon. Anaerobic digestion (AD) is the conversion of organic material directly to a gas, termed biogas, a mixture of mainly methane and carbon dioxide with small quantities of other gases such as hydrogen sulfide. Methane is the major component of the biogas used in many homes for cooking and heating. The biogas has a chemical composition close to that of natural gas. A biodigester, or a biogas plant,

3.6  Biogas

75

Table 3.7  Composition of biogas and landfill gas Component

Chemical formula

Landfill gas

Biogas

Methane (% by vol.)

CH4

40–60

  55–70

Carbon dioxide (% by vol.)

CO2

20–40

  30–45

Nitrogen (% by vol.)

N2

  2–20

   0–2

Oxygen (% by vol.)

O2

420 nm) (Hwang et al., 2004).

128

5  Hydrogen

5.5.5.7 H2 from Photocatalytic Water Splitting Using Photobiocatalytic Method Hydrogen can be generated from water photocatalytically, photobiologically, and photoelectrochemically. The photobiocatalytic method is a novel method of hydrogen production by coupling an inorganic semiconductor with a bacterial enzyme (Gurunathan, 2000). Some researchers have reported on photocatalytic hydrogen production with Cu(II)/WO3 (Maruthamuthu and Ashokkumar, 1988; Maruthamuthu et al., 1989), Cu(II)/Bi2O3 (Maruthamuthu et al., 1993), Rh[III]/Fe2O3 (Gurunathan and Maruthamuthu, 1995), Pt/SnO2 (Gurunathan et al., 1997) using methyl viologen and reported photobiocatalytic hydrogen production using undoped Bi2O3 coupled with photosynthetic bacteria (Maruthamuthu et al., 1992). It is discussed that the nitrogenase enzyme of the bacterial cells is responsible for catalyzing hydrogen production. Sensitization of TiO2 was performed in three ways: 1. Using organic dyes 2. Using Cu(II) ion doping 3. Loading with low band-gap semiconductors (CdS) In the four components, i.e., TiO2/MV2+/electron donor/bacterial cells, each of the last three components has its own specific function and each facilitates the other’s role, thereby enhancing the yield of hydrogen production. It was found that with sensitized TiO2, there is a higher amount of hydrogen production than with the naked TiO2. Among the sensitizers used, Rhodamine B and Ru(bpy)32+ exhibited higher efficiencies compared with other sensitizers, as well as other methods of sensitization (2 and 3) (Gurunathan, 2000). Nikandrov et al. (1988) coupled bacterial enzyme from Thiocapsa roseopersina to TiO2 and observed an efficient photobiocatalytic hydrogen production. Thus a better catalyst has an origin in biology, i.e., bacterial enzyme which catalyzes the hydrogen evolution. TiO2 was coupled to intact bacterial cells of Rhodopseudomonas capsulata species as photocatalyst for hydrogen production using light of λ > 400 nm. The semiconductor-bacterial cells system is then subjected to hydrogen in aqueous solution under visible light using MV2+ (methyl viologen dichloride hydrate) as an electron relay with or without an electron donor (Gurunathan, 2000). 5.5.5.8 Photocatalytic H2 from Sewage Sludge Among various types of biomass, sewage sludge is more difficult to utilize due to its lesser quality. Nevertheless, some attempts have been made for converting sewage sludge into fuel, e.g., by thermochemical pyrolysis (Urban and Antal, 1982; Stolarek and Ledakowicz, 2001; Midilli et  al., 2002) or solubilization methods (Yokoyama et al., 1987; Suzuki et al., 1988; Suzuki et al., 1990; He et al., 2000). Kida et al. (2004) investigated photocatalytic hydrogen production from a digested

5.5  Hydrogen Production Processes

129

sewage sludge solubilized in hot-compressed water (573 K) in order to develop a low-cost sacrificial agent for CdS-based photocatalysts from biomass. H2 evolution occurred over a LaMnO3/CdS composite photocatalyst under Xe lamp irradiation from water containing the solubilized sewage sludge. The amount of evolved H2 reached more than 30 mmol/g catalyst for a 200 h reaction; on the other hand, no H2 was formed in the absence of the solubilized sewage sludge. The H2 evolution rate was comparable to that when typical Na2S–Na2SO3 sacrificial agents were used, suggesting the applicability of a biomass-derived sacrificial agent for photocatalysis. Organic compounds, such as methanol and formic acid, contained in the solubilized sewage sludge are responsible for the H2 evolution observed (Kida et al., 2004).

5.5.6 Solar-Powered Hydrogen Generation Solar radiation is the largest renewable source on earth. A comparative overview of the selected integrated systems indicated that the Sun is the primary source of energy for many of the hydrogen demonstration projects. Electrochemical water splitting powered by photovoltaic arrays produces molecular hydrogen at the cathode, while organic compound oxidation under mild conditions takes place at the anode in competition with the production of oxygen. Hydrogen can be obtained from water by directly connecting a photovoltaic module to a hydrogen generator, with a solid polymer electrolyte (SPE). The electrolysis of water using cells with a SPE is a very efficient method of producing hydrogen. SPE water electrolysis is one of the ways for producing hydrogen with comparatively high levels of efficiency and with compact equipment. SPE is composed of a membrane, cathode and anode which produce hydrogen by providing pure water to one side of a polymer ion exchange film, which is put between the anode and cathode. If hydrogen is produced via solar photovoltaic (PV)-powered water electrolysis, it would be possible, in principle, to provide energy on a global scale, with essentially no greenhouse gas emission and very low local pollution. Accordingly, the operation of electrolyzers with intermittent sources of solar energy and the various possibilities for matching photovoltaic current with the characteristics of the electrolyzer was one of the recurrent design issues in such projects. Most of the electrolyzers were of the alkaline type and operated at low pressure. Concentrated solar radiation can be used for gasification of biomass to produce hydrogen. A detailed review with many references of the technology describes solar gasification of carbonaceous materials to produce a syngas quality intermediate for production of hydrogen and other fuels (Midilli et al., 2000). Shahbazov and Usupov (1994) have shown a good yield of hydrogen from agricultural wastes using a parabolic mirror reflector.

130

5  Hydrogen

5.5.7 Hydrogen from Hydrogen Sulfide Sulfur is recovered from H2S by partial oxidation by the Claus process, and lowquality steam is produced utilizing the heat of reaction. Efforts to produce both hydrogen and sulfur from hydrogen sulfide have been made in recent years through a diverse variety of technologies. These involve thermal, thermochemical, electrochemical, photochemical and plasmochemical methods (Zaman and Chakma, 1995). H2S potentially has economic value if both sulfur and hydrogen can be recovered. Various techniques that are at different stages of development can be considered for the decomposition of H2S and they can be basically grouped into categories of thermal, thermochemical, electrochemical, photochemical and plasmochemical methods (Baykara et al., 2005, 2007). Thermolysis of H2S was carried out in an open tubular reactor quartz tube with argon/H2S feed over a wide composition spectrum (20–100% H2S) at four temperatures (1030–1070 K). These experiments show that the reaction is essentially first order in H2S partial pressure. Hydrogen yield also increases monotonically with feed composition at all temperatures (Adesina et al., 1995). Petrov (1991) suggested the idea for using H2S for production of hydrogen and sulfur in the electrolytic stage of the solar-wind-hydrogen energy systems (SWHES). A thermodynamic model for the partial oxidation of H2S was used to study product compositions attainable in the superadiabatic partial oxidation regime. Superadiabatic partial oxidation techniques permit attainment of operating temperatures significantly in excess of the adiabatic temperature of the incoming reactants (Slimane et al., 2004a). Superadiabatic partial oxidation (combustion) process is the thermal decomposition of H2S in H2S-rich waste streams to high-purity hydrogen and elemental sulfur (Slimane et al., 2002). In the superadiabatic combustion (SAC) process, some part of the H2S is combusted to provide the thermal energy required for the decomposition reaction, as indicated by the following two reactions: 2H2S + O2

→ 2S + H2O

ΔH = –189 269 kJ/mol

(5.34)

H 2S

→ H2 + S

ΔH = +17 423 kJ/mol

(5.35)

As can be seen from Eqs. 5.34 and 5.35, each molecule of H2S reacting with oxygen can provide enough energy to dissociate up to 10 additional molecules of H2S in an available reactor under suitable conditions. The SAC, also known as filtration combustion, consists of combustion of a fuel gas-oxidant mixture in a porous ceramic medium with a high thermal capacity (Kennedy et al., 1995). The intense heat exchange between burning gas mixture and the porous medium permits the accumulation of combustion energy in the solid matrix. Figure 5.5 shows hydrogen recovering from H2S via the superadiabatic combustion (SAC) process.

5.5  Hydrogen Production Processes

131

5.5.7.1 Sulfur–Iodine Thermochemical Water-Splitting Process The sulfur–iodine thermochemical water-splitting cycle (S–I cycle) developed for hydrogen production from water is fundamentally based on the following three chemical reactions (Wang, 2007): H2SO4

→ H2O + SO2 + 0.5O2

(5.36)

2H2O + SO2 + I2

→ H2SO4 + 2HI

(5.37)

2HI

→ H2

(5.38)

+ I2

This process proposes to replace the H2SO4 decomposition with a reaction between H2S and H2SO4 and the replacement gives rise to a H2S-splitting cycle that produces H2 and elemental S from H2S, shown as follows: H2S + H2SO4

→S

+ SO2 + 2H2O

2H2O + I2 + SO2

→ H2SO4 + 2HI

(5.40)

2HI

→ H2

(5.41)

+ I2

(5.39)

Combined with the reactions such as: O2

+S

→ SO2

(5.42)

SO2

+ 0.5O2 → SO3

(5.43)

SO3

+ H2O → H2SO4

(5.44)

This new cycle cannot only produce more H2 and extra H2SO4 but also facilitate a flexible H2 to H2SO4 production ratio. In gas plants, H2 from H2S splitting is an alternative clean fuel. Environmentally, H2 production based on this H2S-splitting cycle is carbon-free. The sulfur–iodine (S–I) thermochemical water-splitting cycle is one of the most studied cycles for hydrogen (H2) production (Huang and Raissi, 2005). The S–I cycle consists of four sections: (I) acid production and separation and oxygen purification, (II) sulfuric acid concentration and decomposition, (III) hydroiodic acid (HI) concentration, and (IV) HI decomposition and H2 purification. Section II of the cycle is an endothermic reaction driven by the heat input from a high-temperature source. Analysis of the S–I cycle in the past thirty years has focused mostly on the utilization of nuclear power as the high-temperature heat source for the sulfuric acid decomposition step. Thermodynamic as well as kinetic considerations indicate that both the extent and rate of sulfuric acid decomposition can be improved at very high temperatures (in excess of 1275 K) available only from solar concentrators. These new sulfuric acid decomposition processes are simpler and more stable than previous processes and yield higher conversion efficiencies for the sulfuric acid decomposition and sulfur dioxide and oxygen formation. Figure 5.5 shows the sulfur–iodine cycle for hydrogen production (Huang and Raissi, 2005; Balat and Ozdemir, 2005).

132

5  Hydrogen

Fig. 5.5  Sulfur–iodine cycle for hydrogen production

5.5.7.2 Pyrolysis of Hydrogen Sulfide Catalytic or non-catalytic, thermal decomposition appears to be the most direct process for obtaining both hydrogen and sulfur from H2S. The reactions involved are highly endothermic and the equilibrium conversion corresponding to a temperature range of 1100–1400  K would be between 10–30%. The conversion level can be increased by catalysis and by removal of H2 and S during reaction. Membrane, thermal diffusion and solar technologies need more development since they seem to be quite promising (Baykara et al., 2005). Production of hydrogen by direct decomposition of hydrogen sulfide has been studied extensively (Clark et al., 1995; Zaman and Chakma, 1995; Luinstra, 1996). Hydrogen sulfide decomposition is a highly endothermic process and equilibrium

5.5  Hydrogen Production Processes

133

Fig. 5.6  CH4/H2S reforming for hydrogen production

yields are poor (Clark et  al., 1995). At temperatures less than 1775  K, the thermodynamic equilibrium is unfavorable toward hydrogen formation. However, in the presence of catalysts such as platinum–cobalt (at 1275 K), disulfides of Mo or W at 1075 K (Kotera et al., 1976), or other transition metal sulfides supported on alumina (at 775–1075 K), H2S decomposition proceeds rapidly (Kiuchi et al., 1982; Bishara et  al., 1987; Al-Shamma and Naman, 1989; Megalofonos and Papayannakos, 1997). 5.5.7.3 Hydrogen Sulfide Reformation of Natural Gas Hydrogen gas can be obtained by direct thermolysis of methane and pyrolysis of hydrogen sulfide. Direct thermal dissociation of methane and H2S does not generate greenhouse gases. However, compared to the steam methane reforming (SMR) process, thermolysis of CH4 and H2S generates smaller amounts of hydrogen per mole of methane and hydrogen sulfide reacted. The reaction of H2S with methane can be thought of as the sulfur analog of the SMR process, as indicated by the following two reactions (Hacisalihoglu et al., 2008): H2S

→ H2 + 0.5S2

ΔH = +79.9 kJ/mol

(5.45)

CH4 + 2S2

→ CS2 + 2H2S

ΔH = –107 kJ/mol

(5.46)

The overall reaction may be written as follows: CH4 + 2H2S → CS2 + 4H2

ΔH = +232.4 kJ/mol

(5.47)

The byproduct obtained from the overall reaction is carbon disulfide (CS2). The reaction between CH4 and H2S given with Eq. 5.47 is the well-known methane process for production of CS2. Most commercial CH4–sulfur processes employ silica gel/aluminum catalyst for CS2 production. The reaction of CH4 with sulfur is thermodynamically favorable for CS2 formation, and conversion is usually in the range of 90 to 95% with respect to methane (Arpe, 1989). The industrial CH4–sulfur pro-

134

5  Hydrogen

Table 5.9  Main hydrogen storage methods and techniques Storage method

Storage condition

Liquid hydrogen in cryogenic tanks

At 21 K

High-pressure gas cylinders

Up to 800 bar

Adsorbed hydrogen on materials

At T < 100 K

Absorbed on interstitial sites in a host metal

At ambient pressure and temperature

Oxidation of reactive metals, e.g., Li, Na, with water

At ambient pressure and temperature

Chemically bonded in covalent and ionic compounds

At ambient pressure

Chemically bonded to either metal or liquid hydrides

At ambient pressure

Chemically carbon bonding

At ambient pressure

cess operates in the temperature range of 775 to 925 K and pressure range of 4 to 7 atm. Figure 5.6 shows the H2S/CH4 reforming process for hydrogen production (Huang and Raissi, 2005; Balat and Ozdemir, 2005).

5.6 Storage of Hydrogen Hydrogen has the highest energy density per unit of weight of any known fuel (excluding nuclear reactions), but 1 g of hydrogen gas occupies about 11 l of space at atmospheric pressure, so its storage for vehicular use presents problems. There are a few different approaches for hydrogen transportation and storage. Hydrogen can be stored as a compressed gas (up to 800 bar), as a liquid (at 21  K) and in solid-state compounds. The first two methods are established technologies with several limitations, the most important of which is their energy-intensive character. Conventional storage systems consist of classical high-pressure tanks and insulated liquid hydrogen systems. Compressing hydrogen is similar to compressing natural gas, though as hydrogen is less dense the compressors need very high-quality seals. The main disadvantages of using hydrogen as a fuel for automobiles are huge on-board storage tanks, which are required because of hydrogen’s extremely low density. Hydrogen may be stored on board a vehicle as compressed gas in ultrahighpressure vessels, as a liquid in cryogenic containers, or as a gas bound with certain metals in metal hydrides. Liquefaction by the Linde cycle, for example, consumes nearly 30% of the total energy contained in the hydrogen and in addition requires expensive equipment and energy to retain hydrogen in the liquid state. Up to 40% of the energy content in the hydrogen can be lost during the liquefaction operation. The liquid hydrogen storage is very expensive in comparison to other methods. The advantage of liquid hydrogen is its high energy-to-mass ratio, three times that of gasoline. However, it is difficult to store and the insulated tank required may be large and bulky (Demirbas, 2007).

5.6  Storage of Hydrogen

135

Table 5.10  Characteristics of six basic hydrogen storage methods Storage media

Pressure (bar)

Temperature (K)

Maximum capacity wt.%

Composite cylinder

800

298

  13

Liquid hydrogen

   1

  21

100

Metal hydrides

   1

298

   2

Complex hydrides

   1

298

  18

Alkali with water

   1

298

  14

Physisorption

  70

  65

   4

Hydrogen can be stored by six different methods and phenomena (Züttel et al., 2003). The main hydrogen storage methods and techniques are given in Table 5.9. The characteristics of six basic hydrogen storage methods are given in Table 5.10. The major challenge with the method of oxidation of reactive metals is the reversibility and the control of the thermal reduction process in order to produce the metal in a solar furnace. Sodium and lithium have a gravimetric hydrogen density of 3 mass% and 6.3 mass%, respectively. Pressurized hydrogen gas occupies a great deal of volume compared with, for example, gasoline with equal energy content, about 30 times larger in volume at 100 bar gas pressure. Condensed hydrogen is about 10 times denser, but is much too expensive to produce and maintain (Jensen et al., 1999). There are also obvious safety concerns with the use of pressurized or liquefied hydrogen in vehicles (David, 2005). Hence, boron has an important role here. Storing hydrogen in a carbon structure is another form of chemical bonding. New forms of carbon structures are currently being researched and promise the best and safest approach as a reversible gas absorption technology. This research is the design and use of carbon nanostructures, either nanotubes or nanofibers. The metal hydrides provide a safe method for fuel storage in hydrogen-powered vehicles. Charging and discharging of the hydride tanks is a process that can be repeated an indefinite number of times provided that the hydride material does not become contaminated. The hydrogen would be transported from the production plant either as a gas or in liquefied form. The liquefied hydrogen, in comparison to gaseous hydrogen, offers the advantages of low pressure and low bulk, but containment difficulties arise from the cryogenic nature of the liquefied gas (Demirbas, 2002). Thermal compression of hydrogen using reversible metal hydride alloys offers an economical alternative to traditional mechanical hydrogen compressors. The hydrogen pressure in a metal hydride increases exponentially with increasing temperature. By employing successively higher-pressure hydride alloy stages in series, high-pressure ratios can be generated. For example, a five-stage hydride compressor will compress a 1.43 atm inlet pressure to 346.94 atm resulting in a compression ratio of 242.6 (Surmen and Demirbas, 2002).

136

5  Hydrogen

Glass microspheres can be used to safely store high-pressure hydrogen. The glass spheres are filled by being immersed in high-pressure hydrogen gas after warming to about 675 K. The fill rate is a function of glass properties, gas permeability, temperature and pressure differential. The spheres are then cooled, locking the hydrogen inside the glass balls. The subsequent increase in temperature will release the hydrogen trapped in the spheres. In the physisorption process a gas molecule interacts with several atoms at the surface of the solid. Once a monolayer of adsorbate molecules is formed the gaseous molecule interacts with a surface of the liquid or solid adsorbate. Therefore, the binding energy of the second layer of adsorbate molecules is similar to the latent heat of sublimation or vaporization of the adsorbate.

5.6.1 Hydrogen Storage with Metal Hydrides Metals, intermetallic compounds, and alloys generally react with hydrogen and form mainly solid metal–hydrogen compounds (MHn). Hydrides exist as ionic, polymeric covalent, volatile covalent and metallic hydrides. Hydrogen reacts at elevated temperatures with many transition metals and their alloys to form hydrides. Many of the MHn show large deviations from ideal stoichiometry (n = 1, 2, 3) and can exist as multiphase systems. Using metal hydrides in electrochemical batteries is an old and rapidly improving method for hydrogen storage. Solid-state materials are attractive due to improved safety, a high energy density, and better energy efficiency (no compression or liquefaction). They are capable of absorbing and desorbing hydrogen with small pressure variations. Utilization of hydrides is also a promising technique for on-board hydrogen storage. A new method is the use of nanostructural materials such as carbon and boron nitride nanotubes, which are known to have the property to store gases within their structure (Fakioglu et al., 2004).

Table 5.11  Hydrogen contents of metal hydrides Metal hydride

Wt.% hydrogen based on formula

LiBH4

21.5

Al(BH4)3

16.8

LiAlH2(BH4)2

15.2

Mg(BH4)2

14.8

Ti(BH4)3

13.0

Fe(BH4)3

11.9

Ca(BH4)2

11.5

Zr(BH4)3

  8.8

5.6  Storage of Hydrogen

137

When hydrogen combines with the metal alloy (in granular form or particles), an exothermic reaction occurs. The gas is thus stored in these metal particles until some heat is applied to release the hydrogen and build up the pressure in the tanks. When a metal hydride absorbs hydrogen, heat is given off. A hydride cold-start heater can be developed that instantly heats an automobile’s catalytic converter when the car is started to dramatically reduce overall exhaust pollution up to 80%. Hydrogen can be chemically bonded to either metal or liquid hydrides. Metal hydrides such as FeTi compounds are used to store hydrogen by bonding it to the surface of the material. As discussed later, the iron-titanium alloy acts as a sponge to absorb the hydrogen, thus becoming a metal hydride (FeTiH1.6) with a physical appearance like that of a fine silvery powder. The safest method for hydrogen storage is the “metal hydride” system (Williamson and Edeskuty, 1986; Veziroglu, 1975). The low-temperature hydrides, FeTiH2 and LaNi5H7, hold hydrogen loosely and evolve it at low temperatures. The high-temperature hydrides, MgH and Mg2NiH4, only release hydrogen at high temperatures since they have high binding enthalpies (Dinga, 1988). Metal hydrides generate hydrogen gas via reversible pyrolysis reactions, i.e., 2M + nH2 ← → 2MHn + Heat

(5.48)

where M is a metal or an alloy. Such reactions are reversible and hydrogen can be stored by hydriding the metal under high pressure exothermically (Fakioglu et al., 2004). Table 5.11 shows the hydrogen contents of metal hydrides. Table 5.12 shows the characteristics of some metal hydrides. Theoretical reversible capacities of alanates such as NaAlH4 and LiAlH4 have been studied to some extent, where the maximum theoretical reversible capacity of NaAlH4 is 5.5% by weight. Hydrolysis is defined as the reaction of a hydride with water to liberate hydrogen gas. The reactions are as follows (Fakioglu et al., 2004): MHn + nH2O → M(OH)n + nH2 (5.49) where M is a metal and n is its valence, or, MXH4

+ 4H2O → 4H2

+ MOH + H3XO3

NaBH4

+ 2H2O → NaBO2 + 4H2 + Heat

(5.50) (5.51)

There are two classes of hydrides: metallic hydrides and complex hydrides. The main difference between these two is the transition of metals to ionic or cova-

Table 5.12  Properties of some metal hydrides Alloy

Weight (kg)

Weight of H2 (kg)

Energy of H2 (MJ)

Energy (MJ/kg)

Fe Ti

563

5.4

767

1.362

Ti Mn TiF

568

6.0

848

1.492

LaNi5

180

2.5

353

1.962

Fe Mn Ti

433

5.0

706

1.629

138

5  Hydrogen

lent compounds for the complex hydrides upon absorbing hydrogen. The complex hydrides of boron represent a very interesting and challenging new hydrogen storage material. Hydrogen storage in boron hydrides is a complex process consisting of many mechanistic steps and depends on important parameters. The boron surface has to be able to dissociate the hydrogen molecule and to allow hydrogen atoms to move easily in order to be able to store hydrogen. Metals differ in the ability to dissociate hydrogen, this ability being dependent on surface structure, morphology and purity (David, 2005). The number of hydrogen atoms per metal atom is 2 in many cases (Zhou, 2005). This kind of complex shows the highest volumetric density and the highest gravimetric density at room temperature known today in lithiumtetrahydroboride (lithiumborohydride, LiBH4). LiBH4 and NaBH4 can reversibly absorb/desorb hydrogen at moderate temperatures, and have therefore, received much attention (Gross et al., 2002; Bogdanovic and Schwickardi, 1997; Bogdanovic et al., 2000; Zaluska et al., 2000; Zaluska et al., 1999). Direct synthesis from the metal, boron and hydrogen at 825–975 K and 30–150 bar H2 has yielded the lithium salt, and such a method is generally applicable to groups IA and IIA metals (Goerrig, 1958). The reaction involving either the metal or the metal hydride, or the metal together with triethylborane in an inert hydrocarbon has formed the basis of a patent. M + B + 2H2 → MBH4

Fig. 5.7  Hydrogen absorption capacity of metal hydride alloy

(5.52)

5.6  Storage of Hydrogen

139

M is Li, Na, K, etc., in Eq. 5.52. The decomposition of the compounds can proceed in one of the following directions: MBH4 → M

+ B + 2H2

(5.53)

MBH4 → MH

+ B + 3/2H2

(5.54)

M is Li, Na, K, etc., for Eqs. 5.53 and 5.54. The thermal decomposition, at least in the early stages, is reversible, as shown by the higher decomposition temperature in the presence of hydrogen than in vacuum or inert gas, and also by the existence of a rapid isotopic exchange between tetrahydroboride and deuterium at T > 625 K (Züttel et al., 2003). The compound with the highest gravimetric hydrogen density at room temperature known today is LiBH4. Therefore, this complex hydride could be the ideal hydrogen storage material for mobile applications. LiBH4 desorbs 3 or 4 hydrogen in the compound upon melting at 553 K and decomposes into LiH and boron. The desorption process can be catalyzed by adding SiO2 and significant thermal desorption was observed starting at 373 K (Züttel et al., 2003). Recently it has been shown, that the hydrogen desorption reaction is reversible and the end-products lithium hydride and boron absorb hydrogen at 980 K and 200 bar to form LiBH4. The scientific understandings of the mechanism of the thermal hydrogen desorption from LiBH4 and the absorption remains a challenge and more research work has to be carried out (Züttel et al., 2004). Thermal compression of hydrogen using reversible metal hydride alloys offers an economical alternative to traditional mechanical hydrogen compressors. The hydrogen pressure in a metal hydride increases exponentially with increasing temperature. The hydrogen absorption capacity of a metal hydride alloy at 298 and 348  K is given in Fig.  5.7. The pressure rise generated in a single hydride heat exchanger is about 300%.

5.6.2 Hydrogen Absorption/Desorption with Oxygen-Contaminated Boron Film The capability of H absorption decreased by 30–50% compared to the pure boron film without oxygen contamination. After the discharge, the depth profile of the oxygen atoms was not changed, which means that a stable oxide layer had formed. The reduction of the H absorption capability occurs probably because the formation of the boron oxide prevents H atoms from becoming trapped in the form of B–H bonding. Most of the retained H atoms can be released by heating up to 775 K with the oxygen contamination. The required temperature for H evacuation is slightly higher than that for the pure boron film. In addition, a small peak was observed at around 475 K. The reduction of H retention can be attributed to the oxide formation followed by the decrease of dangling bond, and thus, the decrease of H trapping sites (Tsuzuki et al., 1999).

140

5  Hydrogen

5.6.3 Hydrogen Storage with Carbon Structures In 1997 the journal Nature was the first publication to discuss the possibility of hydrogen storage in carbon material containing single-walled carbon nanotubes, which estimated for purified tubes a high possible storage capacity at room temperature and ambient pressure (Dillon et al., 1997). This article initiated tremendous research activity on the use of different nanocarbon structures for potential hydrogen storage. Activated carbon has been extensively studied for its gas storage properties. This material was found to be ineffective for storing hydrogen, because only a small percentage of the surface strongly interacted with the hydrogen molecules at ambient temperatures and pressures (Dillon and Heben, 2001). The more recently discovered nanomaterials such as carbon nanotubes (CNTs) and graphitic nanofibers (GNFs) have renewed attention on carbon as an absorbent (Dillon et al., 1997; Fan et al., 1999; Chen et al., 1999; Gupta and Srivastava, 2000). 5.6.3.1 Carbon Nanotubes (CNTs) Carbon nanotube technology is the other new direction being pursued in the search for high-capacity hydrogen storage media. Since their discovery in 1991 by the Japanese electron microscopist Sumio Iijima significant research has been undertaken to improve synthesis methods and more accurately characterize the unique mechanical and chemical properties of carbon nanotubes (Iijima, 1991). Nanotubes can exist as single-walled or as multiwalled units and can be pristine or doped usually with an alkali metal. As a result of van der Waals forces nanotubes can be bundled to form sites where hydrogen can be adsorbed inside the tubes. Carbon nanotubes are microscopic tubes of carbon, two nanometers (billionths of a meter) across, that store hydrogen in microscopic pores on the tubes and within the tube structures. There are a number of options for hydrogen storage in carbon nanotubes. Carbon nanotubes are fullerene-related structures, which consist of graphene microscopic cylinders closed at either end with caps containing pentagonal rings. The apparent advantage of carbon nanotubes is that they are theoretically capable of storing from about 4.2 to 6.5% of their own weight in hydrogen. 5.6.3.2 Carbon Nanofibers and Fullerenes Another variant in carbon nanostructures is carbon nanofiber technology. Carbon nanofibers are grown by the decomposition of hydrocarbons or carbon monoxide over a metal catalyst, and the fibers comprise graphite sheets aligned in a set direction. Graphite nanofibers are ideal for selective gas absorption, as reported by Gupta and Srivastava (2000) who achieved hydrogen adsorption capacities of ~10 wt.% for GNFs grown by thermal cracking. Fan et al. (1999), observed vapor-grown car-

5.7  Hydrogen Storage Materials

141

bon fibers exhibiting 10–13 wt.% hydrogen storage, almost twice as high as the 5.7 wt.% capacity reported by Chen et al. (1999) for the same material. Fullerenes carbon C60 and C70 have been shown to reversibly store hydrogen. Theoretically, fullerene C60 can be hydrogenated up to C60H60, which corresponds to 7.7% weight of hydrogen.

5.7 Hydrogen Storage Materials Hydrogen may be stored on board a vehicle as a gas bound with certain metals, as a liquid in cryogenic containers, or as highly compressed gas in ultrahigh-pressure (69 MPa) vessels. On-board hydrogen storage approaches presently being examined by developers include compressed hydrogen gas, cryogenic gas and liquid hydrogen, metal hydrides, high surface area adsorbents, and chemical hydrogen storage media (Ozturk and Demirbas, 2007). The density of hydrogen in a storage material is crucial for mobile applications. Hydrogen can be stored by six different methods and phenomena (Züttel et  al., 2003): 1. Liquid hydrogen in cryogenic tanks (at 21 K) 2. High-pressure gas cylinders (up to 800 bar) 3. Adsorbed hydrogen on materials with a large specific surface area (at T < 100 K) 4. Absorbed on interstitial sites in a host metal (at ambient pressure and temperature) 5. Oxidation of reactive metals, e.g., Li, Na, with water 6. Chemically bonded in covalent and ionic compounds (at ambient pressure) The main challenge with storing in terms of oxidation of reactive metals is the reversibility and the control of the thermal reduction process in order to produce the metal in a solar furnace, where Na and Li have a gravimetric hydrogen density of 3 mass% and 6.3 mass%, respectively. The density of liquid hydrogen is 70.8 kg/m3 and that of solid hydrogen is 70.6 kg/ 3 m . But the condensation temperature of hydrogen at 1 bar is 21 K and the vaporization enthalpy at the boiling point is 452 kJ/kg. As the critical temperature of hydrogen is 32 K (above this temperature hydrogen is gaseous), liquid hydrogen containers are open systems to prevent strong overpressure. Therefore, heat transfer through the container leads directly to the loss of hydrogen. The continuously evaporated hydrogen may be catalytically burnt with air in the overpressure safety system of the container or collected again in a metal hydride (Schlapbach and Züttel, 2001). The iron–titanium alloy, FeTi, acts as a sponge to absorb the hydrogen, thus becoming a metal hydride (FeTiH1.6). Its physical appearance is like that of a fine silvery powder. The safest method for hydrogen storage is then this metal hydride system (Veziroglu, 1975). When hydrogen combines with the metal alloy (in granu-

142

5  Hydrogen

lar form or particles), an exothermic reaction occurs. The gas is thus stored in these metal particles until some heat is applied to release the hydrogen and build up the pressure in the tanks. When a metal hydride absorbs hydrogen, heat is given off. This process could be used as a cold-start heater that instantly heats an vehicle’s catalytic converter when the car is started, thereby dramatically reducing overall exhaust pollution up to 80%. Thus, metal hydrides provide a safe method for storing fuel in hydrogen-powered vehicles. Charging and discharging of the hydride tanks is a process that can be repeated an indefinite number of times provided that the hydride material does not become contaminated.

5.7.1 Boron Hydrides as Metal Hydrides As mentioned above, the safest method for hydrogen storage is the metal hydride system (Williamson and Edeskuty, 1986; Veziroglu, 1975). When hydrogen combines with the metal alloy, an exothermic reaction occurs. The gas is then stored in the metal particles until some applied heat releases the hydrogen and builds up pressure in the tanks. Heat is then emitted when a metal hydride absorbs hydrogen. Boron absorbs hydrogen and forms hydrides. There are two classes of hydrides: metallic hydrides and complex hydrides, with the main difference being the transition of metals to ionic or covalent compounds for the complex hydrides upon absorbing hydrogen. Boron chemistry is an interesting field of research, which includes plenty of boron hydrides. Some of which are stable, but some are unstable and interconvertible to each other, while producing hydrogen (Turker, 2001). Diborane (B2H6) can be synthesized via various reactions (Durant and Durant, 1970) and produce hydrogen by treatment with H2O, NH3, ROH, etc. (Durant and Durant, 1970; Schriver and Atkins, 1990). The molecular orbital bonding scheme for diborane has been discussed extensively (Lippard and Ucko, 1968). Tetraborane (B4H10) can be obtained by means of various synthetic routes and it also forms by the slow decomposition of diborane (Huhey, 1978; Cotton and Wilkinson, 1967): 2B2H6 ← → B4H10 + H2

(5.55)

B4H10 decomposes from heat treatment (at 363–373  K) to produce diborane (Durant and Durant, 1970; Cotton and Wilkinson, 1967) or at elevated temperatures (at 453–473 K) to produce B5H11 and B5H9. B5H11 is known as unstable pentaborane because it decomposes in a few hours in the cold, mainly to H2 and B10H14 (Durant and Durant, 1970). The necessary condition for hydrogen storage is that the thermodynamic and kinetic conditions are fulfilled. In that case, a metal exposed to hydrogen gas absorbs hydrogen until equilibrium is established. There are a number of reaction steps that kinetically may hinder a hydrogen-storing system from reaching its

5.7  Hydrogen Storage Materials

143

thermodynamical equilibrium of hydrogen storage within a reasonable time. The reaction rate of a metal-hydrogen system is therefore a function of pressure and temperature (David, 2005). The storage of hydrogen in boron hydrides is a complex process consisting of numerous mechanistic steps, depending on many important parameters. For instance, the boron surface must be able to dissociate the hydrogen molecule and to allow hydrogen atoms to move easily in order to be able to store hydrogen. Metals differ in the ability to dissociate hydrogen, this ability being dependent on surface structure, morphology and purity (David, 2005).

5.7.2 Hydrogen in Mechanically Milled Amorphous Boron Hydrogen can be absorbed in amorphous boron by mechanical milling under hydrogen atmosphere, the amount of which has reached up to about 2.3 mass% after 80 h of milling. The trapped hydrogen can be desorbed only as molecular hydrogen in a temperature range of 330–1000 K. Thus the hydrogen desorption in boron is achieved at relatively low temperatures with molecular hydrogen as the sole product (Wang et al., 2003). In contrast to the case of mechanically prepared nanostructured graphite, in which hydrogen desorbs at high temperatures together with desorption of hydrocarbons, hydrogen desorption in boron can be achieved at relatively low temperatures with molecular hydrogen as the sole product. The revealed hydrogenation properties, especially the attracting dehydriding aspect, warrant further investigations of the B–H system from the viewpoint of hydrogen energy storage (Wang et al., 2003).

5.7.3 Boron Complex Hydrides In metal hydrides, the number of hydrogen atoms per metal atom is 2 in many cases (Zhou, 2005). Groups 1–3, light metals, e.g., Li, Mg, B, Al, build a large variety of metal–hydrogen complexes. They are especially interesting because of their light weight and the number of hydrogen atoms per metal atom, which in many cases is 2. The main difference between these complex hydrides and the previously described metallic hydrides is the transition to an ionic or covalent compound of the metals upon hydrogen absorption. Table 5.13 shows the physical properties of some selected complex hydrides (Züttel et  al., 2003). The highest volumetric density and the highest gravimetric density at room temperature known today belong to LiBH4 (18.4 mass%). LiBH4 has stability compared to other chemical hydrides, and can easily be converted to H2. As for NaBH4, along with LiBH4, it can reversibly absorb/desorb hydrogen at moderate temperatures and has therefore received considerable attention (Gross et al., 2002; Bogdanovic and Schwickardi, 1997; Bogdanovic et al., 2000; Zaluska et al., 2000; Zaluski et al., 1999).

144

5  Hydrogen

Table 5.13  Physical properties of selected complex hydrides Formula

M (g/mol)

ρ (g/cm3)

Tm (K)

Tdec (K)

X (mass%)

Reference

LiBH4

  21.784

0.66

   541

   653

18.4

Schlesinger and Brown, 1940

NaBH4

  37.83

1.074

   778

   673

10.6

Knacke et al., 1991

LiAlH4

  37.95

0.917

 > 398

   398

  9.5

Knacke et al., 1991

KBH4

  53.94

1.178

   858

   773

  7.4

Knacke et al., 1991

NaAlH4

  54.0

1.27

   451

   483

  7.4

Bogdanovic and Schwickardi, 1997

Mg2NiH4

111.3

2.72

   553

  3.6

Sandrock and Thomas, 2001

Mg2FeH6

110.5

2.72

   593

  5.4

Yvon, 1998

Mg3MnH7 134.9

2.30

   553

  5.2

Yvon, 1998

332.5

4.86

 < 373

  2.7

Yvon, 1998

BaReH9

M molecular mass, ρ gravimetric density, Tm melting point, Tdec decomposition temperature, X gravimetric hydrogen density

Boron builds a large variety of metal-hydrogen complexes. It is especially interesting because of its light weight and the number of hydrogen atoms per metal atom. The hydrogen in the complex hydrides is often located at the corners of a tetrahedron with boron in the center. The negative charge of the anion, [BH4–], is compensated by a cation, e.g., Li or Na. The hydride complexes of borane and the tetrahydroborates M(BH4) are interesting storage materials (M = Li, Na, K, etc.); however, they are known to be stable and decompose only at elevated temperatures and often above the melting point of the complex (Züttel et al., 2004). Schlesinger and Brown synthesized the lithiumtetrahydroboride (lithiumborohydride) (LiBH4) by the reaction of ethyllithium with diborane (B2H6) in 1940 (Schlesinger and Brown, 1940). It was the first report of a pure alkali metal tetrahydroboride. The direct reaction of the corresponding metal with diborane in ethereal solvents under suitable conditions produces high yields of the tetrahydroborides (Huhey, 1978): 2MH + B2H6 ← → 2MBH4

(5.56)

where M is a metal such as Li, Na, K, etc. Stasinevich and Egorenko (1968) investigated the alkali metal tetrahydroborides by means of thermal analysis in hydrogen at pressures up to 10 bar. The thermal decomposition, at least in the early stages, is reversible, as is shown by the decomposition temperature being higher in the presence of hydrogen than in vacuum or inert gas (Ostroff and Sanderson, 1957; Mesmer and Jolly, 1962) and also by the existence (Mesmer and Jolly, 1962; Brown et al., 1952) of a rapid isotopic exchange between tetrahydroboride and deuterium at T > 625 K (Züttel et al., 2003).

5.8  Hydrogen Fuel for Internal Combustion Engine

145

The compound with the highest gravimetric hydrogen density at room temperature known today is LiBH4 (~18 mass%). Therefore, this complex hydride could be the ideal hydrogen storage material for mobile applications. LiBH4 desorbs 3 or 4 hydrogen in the compound upon melting at 553 K and decomposes into LiH and B. The process of desorption can be catalyzed by adding SiO2; significant thermal desorption was observed starting at 373 K (Züttel et al., 2003). Recently it has been shown that the hydrogen desorption reaction is reversible and the end-products lithium hydride and boron absorb hydrogen at 963 K and 200 bar to form LiBH4. The scientific understanding of the mechanism of the thermal hydrogen desorption from LiBH4 and the absorption remains a challenge; thus, more work must be carried out (Züttel et al., 2004). LiBH4 desorbs the hydrogen only at temperatures from 353 K up to 873 K (Brown et al., 1952). The decomposition temperature of NaAlH4 can be lowered by doping the hydride with TiO2, and the reversibility of the reaction for several desorption/absorption cycles is shown. This is a good example demonstrating the potential of boron hydrides. Al(BH4)3 is a complex hydride with a very high gravimetric hydrogen density of 17 mass%, and the highest known volumetric hydrogen density of 150 kg/m3. Al(BH4)3 has a melting point of 208 K and is the only liquid hydride at room temperature. The complex hydrides of boron represent a very interesting and challenging new hydrogen storage material.

5.8 Hydrogen Fuel for Internal Combustion Engine Water is a readily available resource for generating of hydrogen. With 70% of the world’s surface being covered by water, it is one of the most abundant resources on this planet. For more than a decade, hydrogen as an alternative to traditional energy sources such as oil and natural gas has been the focus of research and development efforts in all technologically advanced countries of the world. In the pursuit for a cleaner world, hydrogen power is perhaps the cleanest fuel alternative. Hydrogen exhibits the highest heating value of all chemical fuels (Demirbas, 1998). The energy from 1 kg hydrogen is equivalent to 2.1 kg natural gas and 2.8 kg petroleum. A hydrogen engine has both the advantages of the high thermal efficiency of a diesel engine (Das, 1996) and the excellent operating performance of a petrol engine (Gren and Glasson, 1992). In the automotive world, hydrogen can be utilized in two ways: hydrogen can be internally combusted to generate power or it can be combined with oxygen in a fuel cell to generate electricity. Internal combustion engines that run on hydrogen are virtually identical to their gasoline predecessors. The difference is that water is the byproduct from combustion with oxygen rather than harmful pollutants. Because the engine runs on hydrogen gas, there are some slight changes in the engine design. Hydrogen has a very wide explosive range (from 4 to 75% in air) in which it can be combined with oxygen to explode. This explosive range is significantly larger than that of gasoline. Therefore, on hydrogen internal combustion engines (HICEs) there is an electronic

146

5  Hydrogen Carburetor Gasoline vapor

Manifold Air

Air

a

Gasoline

Air

H2

Air

Gaseous hydrogen

b

Fig. 5.8  a Carburetor in a liquid gasoline-fueled Otto engine. b Manifold in gaseous hydrogen-fueled modified engine systems

throttle system which controls the air coming into the engine so that the engine can always run at a lean mixture of air and fuel. Another characteristic of HICEs is that they use high-compression pistons such that more power can be achieved from the combustion process. The performance of hydrogen fuel cell vehicles must be comparable or superior to today’s gasoline vehicles in order to achieve widespread commercial success. The most critical issues facing the automotive fuel cell developer are overall power plant efficiency, interfacing the power plant with the fuel’s infrastructure, achieving ultralow or zero emissions, and power plant costs. Fuel cells are very useful as power sources in remote locations, such as spacecraft, remote weather stations, large parks, rural locations, and in certain military applications. There are numerous prototype or production cars and buses based on fuel cell technology being researched or manufactured. A practical commercial fuel cell automobile is not expected until at least 2015 according to the automobile industry. The hydrogen would be transported from the production plant either as a gas or in liquefied form. The liquefied hydrogen, in comparison to gaseous hydrogen, offers the advantages of low pressure and low bulk, but containment difficulties arise from the cryogenic nature of the liquefied gas (Demirbas, 2002). Figure 5.8a,b shows a carburetor in a liquid gasoline-fueled Otto engine and the manifold in a gaseous hydrogen-fueled modified engine system.

5.8.1 Advantages of Hydrogen as an Engine Fuel Hydrogen can be used as a motor fuel, whereas neither nuclear nor solar energy can be used directly. Nuclear power requires heavy shielding to keep the neutrons away from people, but is too heavy for cars. It can be used in ships especially submarines

5.8  Hydrogen Fuel for Internal Combustion Engine

147

and aircraft carriers. Hydrogen fuel is hydrogen gas with small amounts of oxygen and other materials added. Benefits include cleaner air, cleaner water, and better health. Hydrogen is also a renewable resource. Hydrogen has many properties that make it ideal as a fuel for internal combustion engines in automobiles. When hydrogen is burned in air the main product is water. Should greenhouse warming turn out to be an important problem, the key advantage of hydrogen is that carbon dioxide (CO2) is not produced when hydrogen is burned. Hydrogen combustion does not produce toxic products such as hydrocarbons (CxHy), carbon monoxide (CO), oxides of sulfur (SOx), organic acids, and CO2. Acid rain and the CO2 greenhouse effect could effectively be eliminated. Hydrogen contains 2.75 times as much energy as the same weight of gasoline. Hydrogen has a high flame speed, wide flammability limits, and a high detonation temperature with lean burning, which give improved engine efficiency. Hydrogen is a gas at 20.13 K; therefore, there is no problem in starting an engine at the coldest winter temperatures, i.e., instant start-up. As with any gasoline engine, efficiency depends on driving conditions. At freeway speeds the hydrogen engine has demonstrated at least a 20% increase in efficiency. Hydrogen engines demonstrate the efficient operations of a diesel and the high rpm characteristics of a gasoline motor. The thermodynamic cycle for hydrogen is much closer to the ideal Otto cycle than for either a gasoline or a diesel engine. In addition, the compression ratio can be higher.

5.8.2 Disadvantages of Hydrogen as an Engine Fuel The main disadvantages of using hydrogen as a fuel for automobiles are huge onboard storage tanks, which are required because of hydrogen’s extremely low density. Hydrogen may be stored on board a vehicle as compressed gas in ultrahighpressure vessels, as a liquid in cryogenic containers, or as a gas bound with certain metals in metal hydrides. It is expensive to bring hydrogen to mass production. The easiest and cheapest way to refine hydrogen is by electrolysis, which uses electricity to process hydrogen from water. However, most of our cheap electricity comes from fossil fuels, which pollute the environment. Hydrogen can be used as a fuel directly in an internal combustion engine not much different from the engines used with gasoline. The problem is that while hydrogen supplies three times the energy per pound of gasoline, it has only onetenth the density when the hydrogen is in a liquid form and much less when it is stored as a compressed gas. This means that hydrogen fuel tanks must be large. Demonstrations of hydrogen-powered vehicles have usually used compressed hydrogen gas. However, because of the low density, compressed hydrogen will not give a car as useful a range as gasoline. It may be even worse than using lead-acid batteries. Hydrogen can achieve a reasonable density adsorbed in metal hydrides, but then the weight of the metals makes the system very heavy.

148

5  Hydrogen

Hydrogen does not occur freely in nature in useful quantities. It has to be made, usually by splitting water to get the hydrogen. This requires all the energy you are going to get from burning the hydrogen and a bit more on account of inefficiencies. Therefore, hydrogen is an energy transfer medium rather than a primary source of energy. Hydrogen is the lightest of the elements with an atomic weight of 1.0. Liquid hydrogen has a density of 0.07 grams per cubic centimeter, whereas water has a density of 1.0 g/ml and gasoline about 0.75 g/ml. A hydrogen fuel tank will have three times the size of a gasoline tank. Also it must be insulated, and this will add to its bulk. This seems entirely bearable. These facts give hydrogen both advantages and disadvantages. The advantage is that it stores approximately 2.6 times the energy per unit mass as gasoline, and the disadvantage is that it needs about four times the volume for a given amount of energy. A 15-gallon automobile gasoline tank contains 90 pounds of gasoline. The corresponding hydrogen tank would be 60 gallons, but the hydrogen would weigh only 34 pounds. Liquid hydrogen is cold enough to freeze air, and accidents have occurred from pressure build-up following plugged valves. Limited accident experience suggests that the danger is somewhat less with hydrogen than with gasoline, because the hydrogen dissipates rapidly. Although, the release of hydrogen into a confined space like a garage risks an explosion.

5.9 Liquefaction and Compression of Hydrogen The liquefaction of hydrogen above 20 K is not possible with known non-catalytic methods. The advantage of liquid hydrogen is its high energy mass ratio, three times that of gasoline, but up to 40% of the energy content in the hydrogen can be lost during the liquefaction operation. Hydrogen in 38 atm

Hydrogen out 116 atm

Hydride alloy

Cold water

Hot water

Step 1 Fig. 5.9  Thermal hydrogen compression with a two-step process

Step 2

5.9  Liquefaction and Compression of Hydrogen

149

Fig. 5.10  Ortho- and para-hydrogen structures

Energy is needed to compress gases. The compression work depends on the thermodynamic compression process. The ideal isothermal compression cannot be realized. Even more energy is needed to compact hydrogen by liquefaction. Low density and extremely low boiling point of hydrogen increases the energy cost of compression or liquefaction. The activated hydrogen molecules can be attracted to each other more than normal hydrogen molecules in the reaction medium and these attractions may result easily in liquefaction of hydrogen in reaction conditions (Fig. 5.12). Thermal hydrogen compression with a two-step process is given in Fig. 5.9. By employing successively higher-pressure hydride alloy stages in series, high-pressure ratios can be generated. For example, a five-stage hydride compressor will compress a 0.14 MPa inlet pressure to 35 MPa, resulting in a compression ratio of 25 MPa (Surmen and Demirbas, 2002). A major concern in liquid hydrogen storage is minimizing hydrogen losses from liquid boil-off. Because liquid hydrogen is stored as a cryogenic liquid that is at its boiling point, any heat transfer to the liquid causes some hydrogen to evaporate. Liquefaction by the Linde cycle, for example, consumes nearly 30% of the total energy contained in the hydrogen and in addition requires expensive equipment and energy to retain hydrogen in the liquid state. Up to 40% of the energy content in the hydrogen can be lost during liquefaction operation. Figure 5.10 shows the ortho- and para-structures of hydrogen. Normal hydrogen includes 75% ortho- and 25% para-hydrogen, while liquid hydrogen is composed of 0.2% ortho- and 99.8% para-structures. The source of this heat can be ortho-to-para conversion, mixing or pumping energy, radiant heating, convection heating or conduction heating. The liquid hydrogen storage is very expensive in comparison to other methods.

5.9.1 Nanocatalytic Liquefaction of Hydrogen The experiments of nanocatalytic liquefaction of hydrogen were carried out using a platinum-supported carbon nanolayer. In the experiments, H2PtCl6, 6H2O or H2PtCl6 was used as a Pt precursor. To prepare the Pt catalytic reaction nanolayer, the required amounts of H2PtCl6 were mixed with 5 wt.% carbon prepared by burning naphthalene in air (Demirbas, 2008). All the runs were performed in a 100-ml cylindrical autoclave. The catalyzed carbon and hydrogen gas was loaded into an autoclave. The autoclave was cooled

150

5  Hydrogen

Yield of hydrogen liquefaction (wt% of used C)

8

7

6

5

4

3

5

10

15

20

25 30 35 Liquefaction time (min)

40

45

50

Fig. 5.11  Plot for yield of hydrogen liquefaction on Pt-supported carbon versus time

using an external liquid nitrogen bath. The nominal reaction time is 30 min. After each run, non-liquefied hydrogen gas was vented and then the autoclave was heated with an external heater for determining the liquefaction hydrogen in the reaction conditions (Demirbas, 2008). Figure 5.11 shows the plot for yield of hydrogen liquefaction on Pt-supported carbon versus liquefaction time. The yield of hydrogen liquefaction increased with increasing liquefaction time. The nominal liquefaction time was 30 min in reaction conditions. The yield of liquefied hydrogen was 7.4% weight of Pt-catalyzed carbon. Hydrogen consists of a mixture of two types of molecule, ortho-hydrogen, in which the two proton spins are parallel, and para-hydrogen, in which they are antiparallel. There are a number of possible methods for measuring the proportion of ortho- to para-molecules in a sample of hydrogen gas (Farkas, 1935; Stewart and Squires, 1955; Silvera and Pravica, 1998). At hydrogen’s boiling point of 20 K, the equilibrium concentration is almost all para-hydrogen, but at room temperature or higher, the equilibrium concentration is 25% para-hydrogen and 75% ortho-hydrogen (Noganow, 1992). The uncatalyzed conversion from ortho- to para-hydrogen proceeds very slowly, so without a catalyzed conversion step, the hydrogen may be liquefied, but may still contain significant quantities of ortho-hydrogen. This ortho-hydrogen will eventually be converted into the para-form in an exothermic reaction (Timmerhaus and Flynn, 1989). Figure 5.12 shows the structure of the activated hydrogen molecule. The Pt catalyst may cause the increase of activation of the hydrogen molecule. As mentioned before, since the activated hydrogen molecules are more likely to be attracted each other than normal hydrogen molecules in the reaction medium, these attractions may result in liquefaction of hydrogen.

5.9  Liquefaction and Compression of Hydrogen

151

Catalyst

Hydrogen molecule

Activated hydrogen molecule

Fig. 5.12  Structure of activated hydrogen molecule

Table 5.14  Catalysts prepared from different precursors Precursor (wt.%)

Catalyst

Composition

Loading ratio

H2PtCl6 . 6H2O

Pt

Single

5.0

RuCl3 . 3H2O + H2PtCl6 . 6H2O

Ru

Composite

2.5

Pt

2.5

K2PtCl4

Pt

Single

5.0

RuCl3 . 3H2O + K2PtCl4

Ru

Composite

2.5

Pt

2.5

Carbon-supported platinum (Pt) and platinum–ruthenium (Pt–Ru) alloy are one of the most popular electrocatalysts in polymer electrolyte fuel cells (PEFC). Pt supported on electrically conducting carbons, preferably carbon black, is being increasingly used as an electrocatalyst in fuel cell applications (Parker et al., 2004). Carbon-supported Pt could be prepared at loadings as high as 70 wt.% without a noticeable increase of particle size. Unsupported and carbon-supported nanoparticle Pt–Ruadatom (Pt–Ruad) catalysts prepared using the surface reductive deposition technique were evaluated as anode catalysts in liquid feed PEM-DMFCs. It was found that the surface composition of unsupported Pt–Ruad nanoparticles has a significant influence on their activities as anode catalysts in direct methanol fuel cells (Cao and Bergens, 2004). Carbon-supported Pt–Ruad catalysts display higher mass activities than unsupported Pt–Ruad. The electrochemical deposition of Pt–Ru nanoparticles on carbon nanotube electrodes and their electrocatalytic properties have been investigated by He et al. (2004). Table 5.14 shows the catalysts Pt and Ru, prepared from various precursors serving as electrolytic electrodes in the fuel cells (Chaurasia et al., 2003). Activated carbon has been extensively studied for its gas storage properties. This material was found to be ineffective for storing hydrogen, because only a small percentage of the surface strongly interacted with the hydrogen molecules at ambient temperatures and pressures (Dillon and Heben, 2001). The more recently discovered nanomaterials such as carbon nanotubes (CNTs) and graphitic nanofibers (GNFs) have renewed attention on carbon as an absorbent (Dillon et al., 1997; Fan et al., 1999; Chen et al., 1999; Gupta and Srivastava, 2000). Another technology being pursued in the search for high-capacity hydrogen storage media is that of carbon nanotubes. Since their discovery in 1991 by Sumio

152

5  Hydrogen

Iijima, significant research has been undertaken to improve synthesis methods and more accurately characterize the unique mechanical and chemical properties of carbon nanotubes (Iijima, 1991). Nanotubes can exist as single-walled or as multiwalled units and can be pristine or doped usually with an alkali metal. As a result of van der Waals forces nanotubes can be bundled to form sites where hydrogen can be adsorbed inside the tubes. Carbon nanotubes are microscopic tubes of carbon, two nanometers (billionths of a meter) across, that store hydrogen in microscopic pores on the tubes and within the tube structures. There are a number of options for hydrogen storage in carbon nanotubes. Carbon nanotubes are fullerene-related structures, which consist of graphene microscopic cylinders closed at either end with caps containing pentagonal rings. The apparent advantage of carbon nanotubes is that they are theoretically capable of storing from about 4.2 to 6.5% of their own weight in hydrogen. Carbon nanofiber technology is another variant in carbon nanostructures. Carbon nanofibers are grown by the decomposition of hydrocarbons or carbon monoxide over a metal catalyst, and the fibers comprise graphite sheets aligned in a set direction. Graphite nanofibers are ideal for selective gas absorption, with results reported by Gupta and Srivastava (2000) who achieved hydrogen adsorption capacities of ~10 wt.% for GNFs grown by thermal cracking. Fan et  al. (1999) observed vapor-grown carbon fibers exhibiting 10–13 wt.% hydrogen storage, almost twice as high as the 5.7 wt.% capacity reported by Chen et al. (1999) for the same material.

Summary Hydrogen energy is a promising alternative solution because it is clean and environmentally safe. It also produces negligible levels of greenhouse gases and other pollutants when compared with the fossil fuel energy sources they replace. Hydrogen can be obtained by direct electrolysis, by direct thermal conversion, thermochemically, photochemically, photoelectrochemically, and biochemically from water. There are a few different approaches for hydrogen transportation and storage. Hydrogen can be stored as a compressed gas (up to 800 bar), as a liquid (at 21 K) and in solid-state compounds. The first two methods are well-established technologies with several limitations, the most important of which is their energy-intensive character. Conventional storage systems consist of classical high-pressure tanks and insulated liquid hydrogen systems. Compressing hydrogen is similar to compressing natural gas, though as hydrogen is less dense the compressors need very high-quality seals. The main disadvantages of using hydrogen as a fuel for automobiles are huge on-board storage tanks, which are required because of hydrogen’s extremely low density. Hydrogen may be stored on board a vehicle as compressed gas in ultrahigh-pressure vessels, as a liquid in cryogenic containers, or as a gas bound with certain metals in metal hydrides.

References 

153

References Abe, T., Suzuki, E., Nagoshi, K., Miyashita, K., Kaneko, M. 1999. Electron source in photoinduced hydrogen production on Pt-supported TiO2 particles. J Phys Chem B 103:1119–1123. Adesina, A.A., Meeyoo, V., Foulds, G. 1995. Thermolysis of hydrogen sulphide in an open tubular reactor. Int J Hydrogen Energy 20:777–783. Al-Shamma, L., Naman, S.A. 1989. Kinetic study for thermal production of hydrogen from H2S by heterogeneous catalysis of vanadium sulfide in a flow system. Int J Hydrogen Energy 14:173–179. Amiridis, M.D., Duevel, R.V., Wachs, I.E. 1999. The effect of metal oxide additives on the activity of V2O5/TiO2 catalysts for the selective catalytic reduction of nitric oxide by ammonia. Appl Catal B Environ 20:111–122. Anderson, C., Bard, A.J. 1995. Improved photocatalyst of TiO2/SiO2 prepared by a sol-gel synthesis. J Phys Chem 99:9882–9885. Arakawa, H., Sayama, K. 2000. Solar hydrogen production: significant effect of Na2CO3 addition on water splitting using simple oxide semiconductor photocatalysts. Catal Surv Jpn 4:75–80. Arni, S. 2004. Hydrogen-rich gas production from biomass via thermochemical pathways. Energy Edu Sci Technol 13:47–54. Arpe, H. (Ed.) 1989 Ullmann’s Encyclopedia of industrial chemistry. Hydrogen sulfide. 5th edn. Vol. A13, VCH, Weinheim, pp. 467–485. Asahi, R., Morikawa, T., Ohwaki, T., Aoki, K., Tao, Y. 2001. Visible-light photocatalysis in nitrogen-doped titanium oxides. Science 293:269–271. Ashokkumar, M., Kudo, A., Saito, N., Sakata, T. 1994. Semiconductor sensitization by RuS2 colloids on TiO2 electrodes. Chem Phys Lett 229:383–388. Ashokkumar, M., Maruthamuthu, P. 1989. Factors influencing the photocatalytic efficiency of WO3 particles. J Photochem Photobiol A 49:249–258. Bak, T., Nowotny, J., Rekas, M., Sorrell, C.C. 2002. Photoelectrochemical hydrogen generation from water using solar energy: materials-related aspects. Int J Hydrogen Energy 27:991–1022. Balat, M., Ozdemir, N. 2005. New and renewable hydrogen production processes. Energy Sources 27:1285–1298. Bamwenda, G.R., Arakawa, H. 2000. Cerium dioxide as a photocatalyst for water decomposition to O-2 in the presence of Ce-aq(4+) and Fe-aq(3+) species. J Mol Catal A 161:105–113. Baykara, S.Z., Ayfer Kale, A., Veziroglu, T.N. 2005. Possibilities for hydrogen production from H2S in Black Sea. Proceedings International Hydrogen Energy Congress and Exhibition IHEC 2005, Istanbul, Turkey, 13–15 July 2005. Baykara, S.Z., Figen, E.H., Kale, A., Veziroglu, T.N. 2007. Hydrogen from hydrogen sulphide in Black Sea. Int J Hydrogen Energy 32:1246–1250. Berry, G.D., Pasternak, A.D., Rambach, G.D., Smith, J.R., Schock, R.N. 1996. Hydrogen as a future transportation fuel. Energy 21:289–303. Bessekhouad, Y., Trari, M. 2002. Photocatalytic hydrogen production from suspension of spinel powders AMn2O4 (A = Cu and Zn). Int J Hydrogen Energy 27:357–362. Bhaumik, A., Inagaki, S. 2001. Mesoporous titanium phosphate molecular sieves with ionexchange capacity J Am Chem Soc 123:691–696. Bishara, A., Salman, O.A., Khraishi, N., Marafi, A. 1987. Thermochemical decomposition of hydrogen sulfide by solar energy. Int J Hydrogen Energy 12:679–685. Bogdanovic, B., Brand, R.A., Marjanovic, A., Schwikardi, M., Tolle, J. 2000. Metal doped sodium aluminum hydrides as potential new hydrogen storage materials. J Alloys Comp 302:36–58. Bogdanovic, B., Schwickardi, M. 1997. Ti-doped alkali metal aluminum hydrides as potential novel reversible hydrogen storage materials. J Alloys Comp 253–254:1–9. Borgarello, E., Kiwi, J., Graetzel, M., Pelizzetti, E., Visca, M. 1982. Visible-light induced water cleavage in colloidal solutions of chromium-doped titanium-dioxide particles. J Am Chem Soc 104:2996–3002.

154

5  Hydrogen

Brown, W.G., Kaplan, L., Wilzbach, K.E. 1952. The exchange of hydrogen gas with lithium and sodium borohydrides. J Am Chem Soc 74:1348. Buhler, N., Meier, K., Reber, J.F. 1984. Photochemical hydrogen-production with cadmium sulfide suspensions. J Phys Chem 88:3261–3268. Buntkowsky, G., Walaszek, B., Adamczyk, A., Xu, Y., Limbach, H.-H., Chaudret, B. 2006. Mechanism of nuclear spin initiated para-H2 to ortho-H2 Conversion. Phys Chem Chem Phys 16:1929–1935. Caglar, A., Ozmen, H. 2000. Hydrogen: as an attractive fuel in future. Energy Edu Sci Technol 6:1–18 Cao, D., Bergens, S.H. 2004. Pt–Ruadatom nanoparticles as anode catalysts for direct methanol fuel cells. J Power Sources 134:170–180. Cerveramarch, S.C., Borrell, L., Gimenez, J., Simarro, R., Andujar, J.M. 1992. Solar hydrogen photoproduction from sulfide sulfite substrate. Int J Hydrogen Energy 17:683–688. Chaurasia, P.B.L., Ando, Y., Tanaka, T. 2003. Regenerative fuel cell with chemical reactions. Energy Convers Manage 44:611–628. Chen, P., Wu, X., Lin, J., Tan, K.L. 1999. High H2 uptake by alkali-doped carbon nanotubes under ambient pressure and moderate temperatures. Science 285:91–93. Choi, W., Termin, A., Hoffmann, M. 1994. The role of metal ion dopants in quantum-sized TiO2. J Phys Chem 98:13669–13679. Choudhary, T.V., Goodman, D.W. 1999. Stepwise methane steam reforming: a route to CO-free hydrogen. Catal Lett 59:93–94. Choudhary, T.V., Goodman, D.W. 2000. CO-free production of hydrogen via stepwise steam reforming of methane. J Catal 192:316–321. Clark, P.D., Dowling, N.I., Hyne, J.B., Moon, D.L. 1995. Production of hydrogen and sulfur from hydrogen sulfide in refineries and gas processing plants. Alberta Sulphur Res Quart Bull 32:11–28. Cotton, F.A., Wilkinson, G. 1967. Advanced Inorganic Chemistry. Interscience, New York. Dagan, G., Tomkiewicz, M. 1994. Preparation and characterization of TiO2 aerogels for use as photocatalysts. J NonCryst Sol 175:294–302. Das, L.M. 1996. Hydrogen–oxygen reaction mechanism and its implication to hydrogen engine combustion. Int J Hydrogen Energy 21:703–715. David, E. 2005. An overview of advanced materials for hydrogen storage. J Materials Proc Technol 162–163:169–177. De, G.C., Roy, A.M., Bhattacharya, S.S. 1996. Effect of n-Si on the photocatalytic production of hydrogen by Pt-loaded CdS and CdS/ZnS catalyst. Int J Hydrogen Energy 21:19–23. Demirbas, A. 1998. Determination of combustion heat of fuels by using non-calorimetric experimental data. Energy Edu Sci Technol 1:7–12. Demirbas, A. 2002. Fuel properties of hydrogen, liquefied petroleum gas (LPG), and compressed natural gas (CNG) for transportation. Energy Sources 24:601–610. Demirbas, A. 2007. Storage and transportation opportunities of hydrogen. Energy Sources Part B 2:287–295. Demirbas, A. 2008. Nano-catalytic liquefaction of hydrogen. Energy Sources Part A 30:1540–1547. Desilvestro, J., Neumannspallart, M. 1985. Photoredox reactions on semiconductors at open circuit reduction of Fe3+ on WO3 electrodes and particle suspensions. J Phys Chem 89:3684–3689. Dillon, A.C., Heben, M.J. 2001. Hydrogen storage using carbon adsorbents: past, present and future. Appl Phys A 72:133–142. Dillon, A.C., Jones, K.M., Bekkedahl, T.A., Kiang, C.H., Bethune, D.S., Heben, M.J. 1997. Storage of hydrogen in single-walled carbon nanotubes. Nature 386:377–378. Dinga, G.P. 1988. Hydrogen: The ultimate fuel and energy carrier. J Chem Educ 65:688–691. Domen, K., Kudo, A., Onishi, T. 1986. Mechanism of photocatalytic decomposition of water into H-2 and O-2 over NiO – SrTiO3. J Catal 102:92–98. Domen, K., Naito, S., Onishi, T., Tamaru, K. 1982. Photocatalytic decomposition of liquid water on a NiO–SrTiO3 catalyst. Chem Phys Lett 92:433–434. Durant, P.J., Durant, B. 1970. Introduction to advanced inorganic chemistry. Longman, London.

References 

155

Fakioglu, E., Yurum, Y., Veziroglu, T.N. 2004. A review of hydrogen storage systems based on boron and its compounds. Int J Hydrogen Energy 29:1371–1376. Fan, Y.-Y., Liao, B., Liu, M., Wei, Y.-L. Liu, M.-Q., Cheng, H.-M. 1999. Hydrogen uptake in vapor grown carbon nanofibers. Carbon 37:1649–1652. Faherburch, A.L., Bube, R.H. 1983. Fundamentals of Solar Cells. Academic, New York. Farkas, A. 1935. Orthohydrogen, parahydrogen and heavy hydrogen. Cambridge University Press, Cambridge. Fletcher, E.A., Noring, J.E., Murray, J.P. 1984. Hydrogen-sulfide as a source of hydrogen. Int Hydrogen Energy 9:587–593. Fonash, S.J. 1981. Solar cells device physics. Academic, New York. Fujishima, A., Honda, K. 1972. Electrochemical photolysis of water at a semiconductor electrode. Nature 238:37–38. Fujishima, A., Rao, T.N., Tryk, D.A. 2000. Titanium dioxide photocatalysis. J Photochem Photobiol C Photochem Rev 1:1–21. Galinska, A., Walendziewski, J. 2005. Photocatalytic water splitting over Pt TiO2 in the presence of sacrificial reagents. Energy Fuels 19:1143–1147. Goerrig, D. 1958. DBP German Patent 1,077,644. Green, M.A. 1982. Solar cells. Prentice-Hall, Englewood Cliffs, NJ. Gringue, D., Horowitz, G., Garnier, E. 1987. Stabilization of CdS and CdSe photoelectrodes modified by a catalyst-containing polythiophene coating. Ber Buns Phys Chem 91:402–405. Gross, K.J., Thomass, G.J., Jensen, C.M. 2002. Catalyzed alanates for hydrogen storage. J Alloys Comp 330–332:683–690. Gupta, B.K., Srivastava, O.N. 2000. Synthesis and hydrogenation behaviour of graphitic nanofibres. Int J Hydrogen Energy 25:825–830. Gurunathan, K. 2000. Photobiocatalytic production of hydrogen using sensitized TiO–MV2+ system coupled Rhodopseudomonas capsulate. J Mol Catalysis A Chem 156:59–67. Gurunathan, K., Maruthamuthu, P. 1995. Photogeneration of hydrogen using visible-light with undoped doped alpha-Fe2O3 in the presence of methyl viologen. Int J Hydrogen Energy 20:287–295. Gurunathan, K., Maruthamuth, P., Sastri, M.V.C. 1997. Photocatalytic hydrogen production by dye-sensitized Pt/SnO2 and Pt/SnO2/RuO2 in aqueous methyl viologen solution. Int J Hydrogen Energy 22:57–62. Hacisalihoglu, B., Demirbas, A.H., Hacisalihoglu, S. 2008. Hydrogen from gas hydrate and hydrogen sulfide in the Black Sea. Energy Edu Sci Technol 21:109–115. He, P., Gu, G., Shao, L., Zhang, Y. 2000. Research on low temperature thermo-chemical conversion to oil process from sewage sludge. Water Sci Tech 42:301–308. He, Z., Chen, J., Liu, D., Zhou, H., Kuang, Y. 2004. Electrodeposition of Pt–Ru nanoparticles on carbon nanotubes and their electrocatalytic properties for methanol electrooxidation. Diamond Related Mater 13:1764–1770. Herrmann, J.M., Disdier, J., Pichat, P. 1986. Photoassisted platinum deposition on TiO2 powder using various platinum complexes. J Phys Chem 90:6028–6034. Hitoki, G., Takata, T., Kondo, J., Hara, M., Kobayashi, H., Domen, K. 2002. An oxynitride, TaON, as an efficient water oxidation photocatalyst under visible light irradiation (lambda λ ≤ 500 nm). Chem Commun 16:1698–1699. Hohhmann, P. 2002. Tomorrow’s energy: hydroen, fuel cells, and the prospects for a cleaner planet. MIT Press, Cambridge, MA, London, UK, 2002. Höhlein, B., von Andrian, S., Grube, Th., Menzer, R. 2000. Critical assessment of power trains with fuel-cell systems and different fuels. J Power Sources 86:243–249. Huang, C., Raissi, T.-A. 2005. Analysis of sulfur–iodine thermochemical cycle for solar hydrogen production. Part I: decomposition of sulfuric acid. Solar Energy 78:632–646. Huhey, E.J. 1978. Inorganic chemistry. Harper and Row, New York. Hwang, D.W., Kim, H.G., Jang, J.S., Bae, S.W., Ji, S.M., Lee, J.S. 2004. Photocatalytic decomposition of water–methanol solution over metal-doped layered perovskites under visible light irradiation. Catal Today 93–5:845–850.

156

5  Hydrogen

Hwang, D.W., Kim, J., Park, T.J., Lee, J.S. 2002. Mg-doped WO3 as a novel photocatalyst for visible light-induced water splitting. Catal Lett 80:53–57. Iijima, S. 1991. Helical microtubules of graphitic carbon. Nature 354:56–57. Inoue, Y., Kubokawa, T., Sato, K. 1991. Photocatalytic activity of alkali-metal titanates combined with Ru in the decomposition of water. J Phys Chem 95:4059–4063. Ishihara, T., Nishiguchi, H., Fukamachi, K., Takita, Y. 1999. Effects of acceptor doping to KTaO3 on photocatalytic decomposition of pure H2O. J Phys Chem B 103:1–3. Ishikawa, A., Takata, T., Kondo, J.N., Hara, M., Kobayashi, H., Domen, K. 2002. Oxysulfide Sm2Ti2S2O5 as a stable photocatalyst for water oxidation and reduction under visible light irradiation (lambda λ ≤ 650 nm). J Am Chem Soc 124:13547–13553. Jang, J.S., Kim, H.G., Reddy, V.R., Bae, S.W., Ji, S.M., Lee, J.S. 2005. Photocatalytic water splitting over iron oxide nanoparticles intercalated in HTiNb(Ta)O5 layered compounds. J Catal 231:213–222. Jensen, C.M., Zidan, R., Mariels, N., Hee, A., Hagen, C. 1999. Advanced titanium doping of sodium aluminum hydride: segue to a practical hydrogen storage material? Int J Hydrogen Energy 24:461–465. Kamat, P.V. 1989. Photoelectrochemistry in particulate systems 9. Photosensitized reduction in a colloidal TiO2 system using anthracene-9-carboxylic acid as the sensitizer. J Phys Chem 93: 859–864. Kamat, P.V., Fox, M.A. 1983. Photo-sensitization of TiO2 colloids by Erythrosin-B in acetonitrile. Chem Phys Lett 102:379–384. Kapoor, M.P., Inagaki, S., Yoshida, H. 2005. Novel zirconium-titanium phosphates mesoporous materials for hydrogen production by photoinduced water splitting. J Phys Chem B 109:9231–9238. Kato, H., Kudo, A. 1998. New tantalite photocatalysts for water decomposition into H2 and O2. Chem Phys Lett 295:487–492. Kato, H., Kudo, A. 1999a. Photocatalytic decomposition of pure water into H2 and O2 overSrTa2O6 prepared by a flux method. Chem Lett 11:1207–1208. Kato, H., Kudo, A. 1999b. Highly efficient decomposition of pure water into H2 and O2 over NaTaO3 photocatalysts. Catal Lett 58:153–155. Kawai, T., Sakata, T. 1980. Photocatalytic hydrogen production from liquid methanol and water. J Chem Soc Chem Commun 15:694–695. Kennedy, I.H., Dunnwald, D. 1983. Photooxidation of organic-compounds at doped alpha Fe2O3 electrodes. J Electrochem Soc 130:2013–2016. Kennedy, L.A., Fridman, A.A., Saveliev, A.V. 1995. Superadiabatic combustion in porous media: wave propagation, instabilities, new type of chemical reactor. Fluid Mechanics Res 22:1–25. Khan, S.U.M., Al-Shahry, M., Ingler, W.B. 2002. Efficient photochemical water splitting by a chemically modified n-TiO2. Science 297:2243–2245. Kida, T., Guan, G., Yoshida, A. 2003. LaMnO3/CdS nanocomposite: a new photocatalyst for hydrogen production from water under visible light irradiation. Chem Phys Lett 371:563–567. Kida, T., Guan, G., Yamada, N., Ma, T., Kimura, K., Yoshida, A. 2004. Hydrogen production from sewage sludge solubilized in hot-compressed water using photocatalyst under light irradiation. Int J Hydrogen Energy 29:269–274. Kiuchi, H., Nakamura, T., Funaki, K., Tanaka, T. 1982. Recovery of hydrogen from hydrogen sulfide with metals and metal sulfides. Int J Hydrogen Energy 7:477–482. Kiwi, J., Morrison, C. 1984. Heterogeneous photocatalysis-dynamics of charge-transfer in lithiumdoped anatase-based catalyst powders with enhanced water photocleavage under ultravioletirradiation. J Phys Chem 88:6146–6152. Knacke, O., Kubaschewski, O., Hesselmann, K. 1991. Thermochemical Properties of Inorganic Substances, 2nd edn. Springer, Berlin Heidelberg New York. Koca, A., Sahin, M. 2002. Photocatalytic hydrogen production by direct sun light from sulfide/ sulfite solution. Int J Hydrogen Energy 27:363–367. Koca, A., Sahin, M. 2003. Photocatalytic hydrogen production by direct sunlight: a laboratory experiment. J Chem Edu 80:1314–1315.

References 

157

Kohno, M., Kaneko, T., Ogura, S., Sato, K., Inoue, Y. 1998. Dispersion of ruthenium oxide on barium titanates (Ba6Ti17O40, Ba4Ti13O30, BaTi4O9 and Ba2Ti9O20) and photocatalytic activity for water decomposition. J Chem Soc Faraday Trans 94:89–94. Kormann, C., Bahnemann, D.W., Hoffmann, M.R. 1988. Preparation and characterization of quantum-size titanium-dioxide. J Phys Chem 92:5196–5201. Koroneos, C., Dompros, A., Roumbas, G., Moussiopoulos, N. 2005. Advantages of the use of hydrogen fuel as compared to kerosene. Res Conser Recyc 44:99–113. Kotera, Y., Todo, N., Fukuda, K. 1976. Process for production of hydrogen and sulfur from hydrogen sulfide as raw material. US Patent No. 3,962,409. Kudo, A. 2001. Development of photocatalyst materials for water splitting with the aim at photon energy conversion. J Ceram Soc Jpn 109:81–88. Kudo, A., Tanaka, A., Domen, K., Maruya, K., Aika, K., Onishi, T. 1988. Photocatalytic decomposition of water over NiO–K4Nb6O17 catalyst. J Catal 111:67–76. Kudo, A., Kato, H., Nakagawa, S. 2000. Water splitting into H2 and O2 on new Sr2M2O7 (M = Nb and Ta) photocatalysts with layered perovskite structures: factors affecting the photocatalytic activity. J Phys Chem B 104:571–575. Lee, J., Kato, T., Fujishima, A., Honda, K. 1984. Photoelectrochemical oxidation of alcohols on polycrystalline zinc-oxide. Bull Chem Soc Jpn 57:1179–1183. Linsebigler, A., Lu, G., Yates, J.T. 1995. Co-chemisorption on TiO2-oxygen vacancy site influence on co-adsorption. J Chem Phys 103:9438–9443. Lippard, S.J., Ucko, D.A. 1968. Transition metal borohydride complexes. II. Th reaction of copper(I) compounds with boron hydride anions. Inorg Chem 7:1051–1058. Litter, M.I. 1999. Heterogeneous photocatalysis: transition metal ions in photocatalytic systems. Appl Catal B Environ 23:89–114. Luinstra, E. 1996. Hydrogen from H2S: a review of the leading processes. Proceedings of 7th GRI Sulfur Recovery Conference, Gas Research Institute, Chicago, pp. 149–165. Mackor, A., Blasse, G. 1981. Visible-light induced photocurrents in SrTiO3-LaCrO3 single crystalline electrodes. Chem Phys Lett 77:6–8. Malinowska, B., Walendziewski, J., Robert, D., Weber, J.V., Stolarski, M. 2003a. Titania aerogels: preparation and photocatalytic tests. Int J Photoenergy 5:147–152. Malinowska, B., Walendziewski, J., Robert, D., Weber, J.V., Stolarski, M. 2003b. The study of photocatalytic activities of titania and titania-silica aerogels. Appl Catal B Environ 46:441– 451. Maruthamuthu, P., Ashokkumar, M. 1988. Hydrogen generation using Cu(II)/WO3 and oxalic acid by visible-light. Int J Hydrogen Energy 13:677–680. Maruthamuthu, P., Ashokkumar, M., Gurunathan, K., Subramanian, E., Sastri, M.V.C. 1989. Hydrogen evolution from water with visible radiation in presence of Cu(II)/WO3 and electron relay. Int J Hydrogen Energy 14:525–528. Maruthamuthu, P., Gurunathan, K., Subramanian, E., Sastri, M.V.C. 1993. Visible-light induced hydrogen-production with Cu(II)/Bi2O3 and Pt/ Bi2O3/RuO2 from aqueous methyl viologen solution. Int J Hydrogen Energy 18:9–13. Maruthamuthu, P., Muthu, S., Gurunathan, K.,Ashokkumar, M., Sastri, M.V.C. 1992. Photobiocatalysis: hydrogen evolution using a semiconductor coupled with photosynthetic bacteria. Int J Hydrogen Energy 17:863–866. Megalofonos, S.K., Papayannakos, N.G. 1997. Kinetics of catalytic reaction of methane and hydrogen sulphide over MoS2. J Appl Catal A General 165:249–258. Mesmer, R.E., Jolly, W.L. 1962. The exchange of deuterium with solid potassium hydroborate. J Am Chem Soc 84:2039–2042. Midilli, A., Olgun, H., Ayhan, T. 2000. Solar hydrogen production from hazelnut shells. Int J Hydrogen Energy 25:723–732. Midilli, A., Dogru, M., Akay, G., Howarth, C.R. 2002. Hydrogen production from sewage sludge via a fixed bed gasifier product gas. Int J Hydrogen Energy 27:1035–1041. Midilli, A., Ay, M., Dincer, I., Rosen, M.A. 2005. On hydrogen and hydrogen energy strategies I: current status and needs. Renew Sust Energy Rev 9:255–271.

158

5  Hydrogen

Miller, E., Rocheleau, R., Khan, S. 2004. A hybrid multijunction photoelectrode for hydrogen production fabricated with amorphous silicon/germanium and iron oxide thin films. Int J Hydrogen Energy 29:907–914. Miranda, R. 2004. Hydrogen from lignocellulosic biomass via thermochemical processes. Energy Edu Sci Technol 13:21–30. Moon, J., Takagi, H., Fujishiro, Y., Awano, M. 2001. Preparation and characterization of the Sb doped TiO2 photocatalysts. J Mater Sci 36:949–955. Moon, S.C., Mametsuka, H., Tabata, S., Suziki, E. 2000. Photocatalytic production of hydrogen from water using TiO2 and B/TiO2. Catal Today 58:125–132. Namon, S.A., Aliwi, S.M., Alemara, K. 1986. Hydrogen-production from the splitting of H2S by visible-light irradiation of vanadium sulfides dispersion loaded with RuO2. Int J Hydrogen Energy 11:33–38. Navvio, J.A., Testa, J.J., Djedjeian, P., Padron, J.R., Rodriguez, D., Litter, M.I. 1999. Iron-doped titania powders prepared by a sol-gel method. Appl Catal A General 178:191–203. Ni, M., Leung, K.H.M., Leung, D.Y.C., Sumathy, K. 2007. A review and recent developments in photocatalytic water-splitting using TiO2 for hydrogen production. Renew Sustain Energy Rev 11:401–425. Ni, M., Leung, K.H.M., Sumathy, K., Leung, D.Y.C. 2004. Water electrolysis: a bridge between renewable resources and hydrogen. Proceedings of the International Hydrogen Energy Forum, Beijing, PRC, pp. 475–480. Nikandrov, V.V., Shlyk, M.A., Zorin, N.A., Gogotov, I.N., Krosnovsky, A.A. 1988. Efficient photoinduced electron-transfer from inorganic semiconductor TiO2 to bacterial hydrogenase. Febs Lett 234:111–114. Nishikawa, T., Nakajima, T., Shinohara, Y. 2001. An exploratory study on effect of the isomorphic replacement of TiO2. J Mol Struct Theochem 545:67–74. Noganow, L.S. 1992. Hydrogen. McGraw-Hill Encyclopedia of Science & Technology, 7th edn. Vol. 8. McGraw-Hill, New York, pp. 581–588. Ogura, S., Kohno, M., Sato, K., Inoue, Y. 1997. Photocatalytic activity for water decomposition of RuO2-combined M2Ti6O13 (M = Na, K, Rb, Cs). Appl Surf Sci 121:521–524. Ohno, T., Saito, S., Fujihara, K., Matsumura, M. 1996. Photocatalyzed production of hydrogen and iodine from aqueous solutions of iodide using platinum-loaded TiO2 powder. Bull Chem Soc Jpn 69:3059–3064. Okamoto, K., Yamamoto, Y., Tanaka, H., Itaya, A. 1985. Kinetics of heterogeneous photocatalytic decomposition of phenol over anatase TiO2 powder. Bull Chem Soc Jpn 58:2023–2028. Oosawa, Y. 1984. Photocatalytic decomposition of aqueous hydroxylamine solution over anatase and precious metal anatase. J Phys Chem 88:3069–3074. Ostroff, A., Sanderson, R. 1957. Oxidation and thermal decomposition of sodium and potassium borohydrides. J Inorg Nuclear Chem 4:230–231. Ozturk, T., Demirbas, A. 2007. Boron compounds as hydrogen storage materials. Energy Sources Part A 29:1415–1423. Parker, S.F., Taylor, J.W., Albers, P., Lopez, M., Sextl, G., Lennon, D., McInroy, A.R., Sutherland, I.W. 2004. Inelastic neutron scattering studies of hydrogen on fuel cell catalysts. Vibration Spectrosc 35:179–182. Petrov, K. 1995. The Black Sea and hydrogen energy. Int J Hydrogen Energy 16:805–808. Plass, J.H., Barbir, F., Miller, H.P., Veziroglu, T.N. 1990. Economics of hydrogen as a fuel for surface transportation. Int J Hydrogen Energy 15:663–668. Piotrowska, A., Walendziewski, J. 2005. Photocatalytic hydrogen production from the water over titania aerogels under UV irradiation. Proceedings International Hydrogen Energy Congress and Exhibition IHEC 2005, Istanbul, Turkey. Ranjit, K.T., Cohen, H., Willner, I., Bossmann, S., Braun, A. 1999. Lanthanide oxide-doped titanium dioxide: effective photocatalysts for the degradation of organic pollutants. J Mater Sci 34:5273–5280. Reber, J.F., Meier, K. 1984. Photochemical production of hydrogen with zinc-sulfide suspensions. J Phys Chem 88:5903–5913. Rifkin, J. 2002. The hydrogen economy. Jeremy P. Tarcher/Penguin, New York.

References 

159

Rocheleau, R.E., Vierthaler, M. 1994. Optimization of multijunction a-Si:H solar cells using an integrated optical/electrical model, in Proceedings of the 21st World Conference on Photovoltaic Energy Conversion, pp. 567–570. Institute for Electrical and Electronics Engineers, Honolulu, HI. Rostrup-Nielsen, J.R. 1984. Catalytic steam reforming, in Catalysis: science and technology, Vol. 5, J.R. Anderson, M. Boudart. Springer, Berlin Heidelberg New York, pp. 1–117. Sandrock, G., Thomas, G. 2001.The IEA/DOE/SNL on-line hydride databases. Appl Phys A Mater Sci Proc 72A:153–155. Sato, J., Saito, N., Nishiyama, H., Inoue, Y. 2001. New photocatalyst group for water decomposition of RuO2-loaded p-block metal (In, Sn, and Sb) oxides with d10configuration. J Phys Chem B 105:6061–6063. Sayama, K. Arakawa, H. 1992a. Significant effect of carbonate addition on stoichiometric photodecomposition of liquid water into hydrogen and oxygen from platinum titanium (IV) oxide suspension. J Chem Soc Chem Commun 2:150–152. Sayama, K., Arakawa, H. 1992b. Remarkable effect of Na2CO3 addition on photodecomposition of liquid water into H2 and O2 from suspension of semiconductor powder loaded with various metals. Chem Lett 2:253–256. Sayama, K., Arakawa, H. 1996. Effect of carbonate addition on the photocatalytic decomposition of liquid water over a ZrO2 catalyst. J Photochem Photobiol A Chem 94:67–68. Sayama, K., Arakawa, H. 1993. Photocatalytic decomposition of water and photocatalytic reduction of carbon-dioxide over ZrO2 catalyst. J Phys Chem 97:531–533. Sayama, K., Arakawa, H. 1994. Effect of Na2CO3 addition on photocatalytic decomposition of liquid water over various semiconductor catalysts. J Photochem Photobiol A Chem 77:243–247. Schlapbach, L., Züttel, A. 2001. Hydrogen-storage materials for mobile applications. Nature 414:353–358. Schlesinger, H.J., Brown, H.C., 1940. Metallo borohydrides. III. Lithium borohydride. J Am Chem Soc 62:3429–3435. Schriver, D.F., Atkins, P.W. 1990. Langford CH. Inorganic Chemistry. ELBS, Oxford. Serban, A., Nissenbaum, A. 2000. Light induced production of hydrogen from water by catalysis with ruthenium melanoidins. Int J Hydrogen Energy 25:733–737. Serpone, N., Borgarello, E., Gratzel, M. 1984. Visible-light induced generation of hydrogen from H2S in mixed semiconductor dispersions: improved efficiency through inter-particle electron transfer. Chem Commun 6:342–344. Shahbazov, J., Usupov, I. 1994. Non-trading sources of energy for hydrogen. Int J Hydrogen Energy 19:863–864. Silvera, I.F., Pravica, M.G. 1998. Hydrogen at megabar pressures and the importance of ortho– para concentration. J Phys Condens Matter 10:11169–11177. Slimane, R.B., Lau, F.S., Dihu, R., Bingue, J.P., Saveliev, A.V., Fridman, A.A., Kennedy, L.A. 2002. Production of hydrogen by superadiabatic decomposition of hydrogen sulfide, 14th World Hydrogen Energy Conference, Montreal, Quebec, Canada, 9–14 June 2002. Slimane, R.B., Lau, F.S., Khinkis, M., Bingue, J.P., Saveliev, A.V., Kennedy, L.A. 2004a. Conversion of hydrogen sulfide to hydrogen by superadiabatic partial oxidation: thermodynamic consideration. Int J Hydrogen Energy 29:1471–1477. So, W.W., Kim, K.J., Moon, S.J. 2004. Photo-production of hydrogen over the CdS–TiO2 nanocomposite particulate films treated with TiCl4. Int J Hydrogen Energy 29:229–234. Stasinevich, D.S., Egorenko, G.A. 1968. A thermographic investigation of sodium hydroboratesodium hydride system. Russ J Inorg Chem 133:341–343. Stewart, A.T., Squires, G.L. 1955. Analysis of ortho- and para-hydrogen mixtures by the thermal conductivity method. J Sci Instrum 32:26–29. Stolarek, P., Ledakowicz, S. 2001. Thermal processing of sewage sludge by drying, pyrolysis, gasification and combustion. Water Sci Tech 44:333–339. Surmen, Y., Demirbas, A. 2002. Thermochemical conversion of residual biomass to hydrogen for Turkey. Energy Sources 24:403–411.

160

5  Hydrogen

Suzuki, A., Nakamura, T., Yokoyama, S. 1990. Effect of operating parameters on thermochemical liquefaction of sewage sludge. J Chem Eng Jpn 23:6–11. Suzuki, A., Nakamura, T., Yokoyama, S., Ogi, T., Koguchi, K. 1988. Conversion of sewage sludge to heavy oil by direct thermochemical liquefaction. J Chem Eng Jpn 21:288–293. Takata, T., Shinohara, K., Tanaka, A., Hara, M., Kondo, J.N., Domen, K. 1997a. A highly active photocatalyst for overall water splitting with a hydrated layered perovskite structure. J Photochem Photobiol A: Chem 106:45–49. Takata, T., Furumi, Y., Shinohara, K., Tanaka, A., Hara, M., Kondo, J.N., Domen, K. 1997b. Photocatalytic decomposition of water on spontaneously hydrated layered perovskites. Chem Mater 9:1063–1064. Talavera, R.R., Vargas, S., Arroyo-Murillo, R., Montiel-Campos, R., Haro-Poniatowski, E. 1997. Modification of the phase transition temperatures in titania doped with various cations. J Mater Res 12:439–443. Timmerhaus, C., Flynn, T.M. 1989. Cryogenic engineering. Plenum, New York. Tryk, D.A., Fujishima, A., Honda, K. 2000. Recent topics in photoelectrochemistry: achievements and future prospects. Electrochim Acta 45:2363–2376. Tsuzuki, K., Eiki, H., Inoue, N., Sagara, A., Noda, N., Hirohata, Y., Hino; T. 1999. Hydrogen absorption/desorption behavior with oxygen contaminated boron film. J Nuclear Mat 266– 269:247–250. Turker, L. 2001. Diborane–tetraborane conversion in C60 vesicles-a theoretical study. Int J Hydrogen Energy 26:837–842. Urban, D.L., Antal, M.J. 1982. Study of the kinetics of sewage pyrolysis using DSC and DTA. Fuel 61:799–806. Veziroglu, T. 1975. Hydrogen Energy, Part B. Plenum, New York. Viswanathan, B. 2006. An introduction to energy sources. Indian Institute of Technology, Madras, India. Wang, H. 2007. Hydrogen production from a chemical cycle of H2S splitting. Int J Hydrogen Energy 32:3907–3914. Wang, P., Orimo, S., Tanabe, K., Fujii, H. 2003. Hydrogen in mechanically milled amorphous boron. J Alloys Comp 350:218–221. Williamson, K., Edeskuty, F. 1986. Recent developments in hydrogen technology, Vol. I–II. CRC, Boca Raton, FL. Wu, J., Uchida, S., Fujishiro, Y., Yin, S., Sato, T. 1999a. Synthesis and photocatalytic properties of HTaWO6/(Pt, TiO2) and HTaWO6/(Pt, Fe2O3) nanocomposites. Int J Inorg Mater 1:253–258. Wu, J., Uchida, S., Fujishiro, Y., Yin, S., Sato, T. 1999b. Synthesis and photocatalytic properties of HNbWO6/TiO2 and HNbWO6/Fe2O3 nanocomposites. J Photochem Photobiol A Chem 128:129–133. Wu, J., Yin, S., Lin, Y., Lin, J.M., Huang, M.L., Sato, T. 2001. Hydrothermal synthesis of HNbWO6/ MO series nanocomposites and their photocatalytic properties. J Mat Sci 36:3055–3059. Yokoyama, S., Suzuki, A., Murakami, M., Ogi, T., Koguchi, K., Nakamura, E. 1987. Liquid fuel production from sewage sludge by catalytic conversion using sodiumcarbonate. Fuel 66:1150–1155. Yoshimura, J., Ebina, Y., Kondo, J., Domen, K., Tanaka, A. 1993. Visible-light induced photocatalytic behavior of a layered perovskite type niobate. J Phys Chem B 97:1970–1973. Yvon, K. 1998. Complex transition-metal hydrides. Chimia 52:613–619. Zaluska, A., Zaluski, L., Strom-Oslen, J.O. 2000. Sodium alanates for reversible hydrogen storage. J Alloys Comp 298:125–134. Zaluski, L., Zaluska, A., Strom-Olsen, J.O. 1999. Hydrogenation properties of complex alkali metal hydrides fabricated by mechano-chemical synthesis. J Alloys Comp 290:71–78. Zaman, J., Chakma, A. 1995. Production of hydrogen and sulphur from hydrogen sulphide. Fuel Proc Technol 41:159–198. Zhou, L. 2005. Progress and problems in hydrogen storage methods. Renew Sustain Energy Rev 9:395–408. Zou, Z.G., Ye, J.H., Sayama, K., Arakawa, H. 2001. Direct splitting of water under visible light irradiation with an oxide semiconductor photocatalyst. Nature 424:624–627.

References 

161

Züttel, A., Wenger, P., Rentsch, S., Sudan, P., Maurona, P., Emmenegger, C. 2003. LiBH4 a new hydrogen storage material. J Power Sources 118:1–7. Züttel, A., Wenger, P., Sudan, P., Maurona, P., Orimo, S. 2004. Hydrogen density in nanostructured carbon, metals and complex materials. Mater Sci Eng B 108:9–18.

Chapter 6

Biohydrogen

6.1 Introduction Hydrogen is the element of greatest abundance in the universe; however, its production from renewable resources remains a major challenge. Biohydrogen produced from biorenewables is a promising alternative for a sustainable energy source. Biohydrogen is a renewable biofuel produced from biorenewable feedstocks by chemical, thermochemical, biological, biochemical, and biophotolytical methods. As a sustainable energy supply with minimal or zero use of hydrocarbons, hydrogen is a promising alternative to fossil fuel. It is a clean and environmentally friendly fuel, which produces water instead of greenhouse gases when combusted. The topic of renewable resources, biohydrogen in particular, includes energy security, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sectors of all countries in the world. Biohydrogen is an environmentally friendly alternative automotive fuel that can be used in an internal combustion engine. Due to its environmental merits, the share of biohydrogen in the automotive fuel market will grow fast in the next decade. There are several reasons for biohydrogen to be considered as a relevant technology by both industrialized and developing countries. The most known industrial methods for producing hydrogen include steam reformation of natural gas, coal gasification, and splitting water with electricity typically generated from carbonaceous fuels. These energy-intensive industrial processes release carbon dioxide and other greenhouse gases and pollutants as byproducts. In addition to thermochemical hydrogen production by gasification, hydrogen can be produced biologically. There are currently two proposed pathways to use organisms for hydrogen production. Direct production through “photobiohydrogen” utilizes microorganisms capable of using solar photons to separate oxygen from water. Some microorganisms produce hydrogen naturally, and biotechnologies based on these microbial systems could lead to the development of clean, renewable sources of hydrogen. A. Demirbas, Biohydrogen, © Springer 2009

163

164

6  Biohydrogen

The biorenewable feedstocks can be converted to petroleum-substitute fuels. The majority of the bioengineering strategies for biochemically derived fuels involve options for the disposition of organic matter produced via photosynthate. The bulk of the presently exploited photosynthate is directed toward the production of wood, food, and feed. During processing and consumption, biomass materials are generated which can be used for energy production via combustion, pyrolysis or biochemical conversions to ethanol, hydrogen, methane, and isopropanol. A second option is to engineer the photosynthetic apparatus to provide hydrogen. The third strategy is the cultivation of crops as energy sources via the foregoing processes. Biomass has the potential to accelerate the realization of hydrogen as a major fuel of the future. However, obtaining hydrogen from biomass has major challenges. There are no completed technology demonstrations. The yield of hydrogen is low from biomass since the hydrogen content in biomass is low to begin with (approximately 6% versus 25% for methane) and the energy content is low due to the 40% oxygen content of biomass.

6.2 Definition The term biohydrogen (from the Greek words bio meaning life + hydro meaning water + genes meaning born of or forming) refers to non-fossilized and biodegradable organic material originating from plants, animals and microorganisms derived from biological sources. Biohydrogen is defined as hydrogen produced biologically (mostly by bacteria) as a biofuel from waste organic materials. Fermentative biohydrogen production plants are proposed industrial plants for the production of hydrogen. They would typically involve processes such as thermophillic fermentation, dark fermentation and/or photofermentation and gas cleaning. Biohydrogen production can also involve an element of anaerobic digestion where the methane from biogas is converted through steam reforming into hydrogen. Hydrogen produced by microalga and bacteria is biohydrogen (Benemann, 1998). There are currently no practical biohydrogen production processes. However, several concepts have promise for near to long-term process development (Benemann, 1998). Biohydrogen can comprehensively be described as hydrogen, which is produced chemically, thermochemically, biologically, biochemically, and biophotolytically from all biomass materials.

6.3 History Sir E. Ray Lankester (1847–1929) was a prominent biologist who did research on a wide variety of organisms, from protozoa to mammals (Gest and Blankenship, 2004). In 1939 Hans Gaffron (German researcher), while working at the University

6.3  History

165

of Chicago, obtained fermentative and photochemical hydrogen from algae (Gaffron, 1939). Gaffron and Rubin first reported that Scenedesmus, a green microalga, evolved molecular hydrogen under light conditions after being kept in anaerobic and dark conditions (Gaffron and Rubin, 1942). Gest and co-workers studied the metabolism of photosynthetic bacteria: the photochemical production of molecular hydrogen by growing cultures of photosynthetic bacteria (Gest and Kamen, 1949a; Ormerod and Gest, 1962). Gest and Kamen discovered the light-dependent production of H2 and N2 fixation by Rsp. rubrum. Subsequent studies revealed that many anoxygenic phototrophs have N2 fixation capacity (Gest and Kamen, 1949b; Kamen and Gest, 1949), and that Rsp. rubrum can use H2 and CO2 (as the sole carbon source) for photoautotrophic growth in a synthetic medium (Ormerod et al., 1961). Hydrogen gas is a product of the mixed acid fermentation of Escherichia coli, the butylene glycol fermentation of Aerobacter, and the butyric acid fermentations of Clostridium spp. (Aiba et al., 1973). The production of biohydrogen using bacteria and microalga started some 35 years ago with a meeting on “Biological Energy Conservation.” Benemann and co-workers studied the hydrogen evolution from water using Clostridium kluyveri hydrogenase in 1973. Spinach chloroplast preparations were mixed with Clostridium kluyveri hydrogenase and ferredoxin. These findings indicate that hydrogen evolution from water and sunlight by photosynthetic processes could be a method for solar energy conversion. In the summer of 2001, researchers manipulated the photosynthetic process of spinach plants to produce hydrogen. But these biological means of hydrogen production are known only as laboratory experiments. Intense research persists to better understand ways to improve these hydrogen production methods. Biological hydrogen production has been known for over a century and research directed at applying this process to a practical means of hydrogen fuel production has been carried out for over a quarter century. Dark fermentation of biomass or wastes presents an alternative route to biological hydrogen production that has been little studied (Hallenbeck and Benemann, 2002). Researchers have investigated hydrogen production with anaerobic bacteria since the 1980s (Nandi and Sengupta, 1998). Biohydrogen seems particularly suitable for relatively small-scale, decentralized systems, integrated with agricultural and industrial activities or waste processing facilities for the future renewable energy demands (Kotay and Das, 2008). Direct hydrogen conversion from sunlight may offer higher theoretical efficiencies (Akkerman et al., 2002) compared to the 0.2 to 2.6% photosynthetic efficiencies in energy crops today (Klas, 2004). However, the scientific and technical feasibility of the process requires more development, and the costs of a photobioreactor will also be a challenge. Indirect biohydrogen involves oxygen inhibition of the electron transfer step and hydrogenase production of hydrogen from carbohydrates (Masukawa et al., 2002). Several reviews have examined the potential of biological hydrogen production (Madamwar et al., 2000; Melis and Happe, 2001; Levin et al., 2004; Nath and Das, 2004; Prince and Kheshgi, 2005). Although microorganisms produce hydrogen by different mechanisms, the step can be represented by the simple chemical reaction

166

6  Biohydrogen

2H+ + 2e → H2. This reaction is known to be catalyzed by either nitrogenase or hydrogenase enzymes. Although alternative biological hydrogen production pathways exist, each with its own set of advantages and disadvantages, the following discussion on biohydrogen production will focus on challenges that must be overcome to improve one type of biological hydrogen production known as biophotolysis. Biophotolysis holds potential for the scale of hydrogen production necessary to meet future energy demand. One advantage of biophotolysis is that it is a more efficient conversion of solar energy to hydrogen. Theoretically, the maximal energetic efficiency for direct biophotolysis is about 40% (Prince and Kheshgi, 2005). Appropriate enzymes then perform an electrochemical process that unites two electrons from the oxygen-producing step with two H+ ions to make hydrogen as the other product. Indirect hydrogen production through photosynthesis in microalgae uses a dark fermentation step where the carbohydrate produced by photosynthesis is converted to hydrogen gas. Hydrogen-intensive research work has already been carried out on the advancement of these processes, such as the development of genetically modified microorganisms, metabolic engineering, improvement of the reactor designs, use of different solid matrices for the immobilization of whole cells, biochemical assisted bioreactor, development of two-stage processes, etc., for higher H2 production rates. Pilot plant trials of the photofermentation processes require more attention. Use of cheaper raw materials and efficient biological hydrogen production processes will surely make them more competitive with the conventional H2 generation processes in the near future (Das and Veziroglu, 2008).

6.4 Hydrogen from Biorenewables via Biological Processes Biological generation of biohydrogen technologies provide a wide range of approaches to generate hydrogen, including direct biophotolysis, indirect biophotolysis, photofermentations, and dark fermentation by a combination of these processes. It is important to develop hydrogen generation methods that are renewable like biohydrogen. Biohydrogen production processes are found to be more environmentally friendly and less energy intensive as compared to thermochemical and electrochemical processes. There are three types of microorganisms that generate hydrogen: cyanobacteria, anaerobic bacteria, and fermentative bacteria. The cyanobacteria directly decompose water to hydrogen and oxygen in the presence of light energy by photosynthesis. Photosynthetic bacteria use organic substrates like organic acids. Anaerobic bacteria use organic substances as the sole source of electrons and energy, converting them into hydrogen. Biohydrogen can be generated using bacteria such as Clostridia by controlling temperature, pH, reactor hydraulic retention time (HRT) and other factors of the treatment system. Biological hydrogen can be generated from plants by biophotolysis of water using microalgae (green algae and cyanobacteria), fermentation of organic com-

6.4  Hydrogen from Biorenewables via Biological Processes

167

pounds, and photodecomposition of organic compounds by photosynthetic bacteria. To produce hydrogen by fermentation of biomass, a continuous process using a non-sterile substrate with a readily available mixed microflora is desirable (Hussy et al., 2005). A successful biological conversion of biomass to hydrogen depends strongly on the processing of raw materials to produce feedstock, which can be fermented by the microorganisms. Biochemical and biological processes have many advantages: 1. No unwanted and hazardous byproducts are formed. 2. They occur at ambient temperatures and pressures. 3. No special equipment is needed. 4. All are renewable energy sources. 5. They are ecofriendly processes. Green chemistry offers cleaner processes for energy abatement. Some of these energy conversion processes are: 1. Photosynthesis 2. Glycolysis 3. Nitrogen fixation 4. Fermentation processes Although some of the steps in photosynthesis are still not fully understood, the overall photosynthetic reaction has been known since the 1800s. Jan van Helmont began the research of the process in the mid-1600s when he carefully measured the mass of the soil used by a plant and the mass of the plant as it grew. After noticing that the soil mass changed very little, he hypothesized that the mass of the growing plant must come from the water, the only substance he added to the potted plant. Photosynthesis is the most important biochemical process in which plants, algae, and some bacteria harness the energy of sunlight to produce food. Organisms that produce energy through photosynthesis are called photoautotrophs. Photosynthesis is a process in which green plants utilize the energy of sunlight to manufacture carbohydrates from carbon dioxide and water in the presence of chlorophyll (Viswanathan, 2006). The initial process in photosynthesis is the decomposition of water into oxygen and hydrogen and oxygen will be released. The simplified photosynthesis pathways are given in Fig. 6.1 and Eqs. 6.1 and 6.2. The hydrogen and the carbon and oxygen of carbon dioxide are then converted into formaldehyde (Fig. 6.1). Then, a series of increasingly complex compounds results finally in a stable organic compound, hexose (typically glucose) (Eq. 6.1). This phase of photosynthesis utilizes stored energy and therefore can proceed in the dark. Hexose is polymerized into hexosan (typically glucosan) or carbohydrates (Eq. 6.2). Glucose formation: 6CH2O   →   C6H12O6 Formaldehyde Glucose

(6.1)

168

6  Biohydrogen

Glucosan formation via polymerization: nC6H12O6 → (C6H12O6)n Glucose Glucosan

(6.2)

In general, the results of this process are the reverse of those in respiration, in which carbohydrates are oxidized to release energy, with the production of carbon dioxide and water. The intermediary reactions before glucose is formed involve several enzymes, which react with the coenzyme ATP (adenosine triphosphate) to produce various molecules. The main product, glucose, is the fundamental building block of carbohydrates (e.g., sugars, starches, and cellulose). Cellulose is used to build the rigid cell walls that are the principal supporting structure of plants. Plants are photoautotrophs, which mean they are able to synthesize food directly from inorganic compounds using light energy, instead of eating other organisms or relying on material derived from them. The energy for photosynthesis ultimately comes from absorbed photons and involves a reducing agent, which is water in the case of plants, releasing oxygen as a waste product. The light energy is converted to chemical energy, in the form of ATP and NADPH, using the light-dependent reactions and is then available for carbon fixation (Viswanathan, 2006). Energy and carbon are obtained by organisms either directly or indirectly via the photosynthetic conversion of solar energy. The majority of the bioengineering strategies for biochemically derived fuels involve options for the disposition of organic matter produced via photosynthate. During processing and consumption, waste organic materials are generated which can be used for energy production via combustion, pyrolysis or biochemical conversions to ethanol, hydrogen, methane, and isopropanol. Nitrogen fixation is the process by which nitrogen is taken from its relatively inert molecular form in the atmosphere and converted into nitrogen compounds useful for other chemical processes. Hydrogen gas is also released during the biological nitrogen fixation process. A promising method is the biological production of hydrogen by fermentation. Fermentative hydrogen production is the fermentative conversion of organic substrate to biohydrogen manifested by a diverse group of bacteria using multienzyme systems involving three steps similar to anaerobic conversion. Fermentative/hydrolytic microorganisms hydrolyze complex organic polymers to monomers, which further convert to a mixture of lower molecular weight organic acids and alcohols by obligatory H2-producing acidogenic bacteria. The production of biohydrogen occurs in the second and third step of anaerobic degradation. Thereby, methanogenic bacteria must be inhibited to avoid the consumption of H2 to produce CH4. The fermentative production of biohydrogen is characterized by a lower technical complexity compared to photofermentation. At that light-independent hydrogen production

CO2 + H2 O + Solar energy

T > 285 K, Chlorophyll

Fig. 6.1  Formaldehyde formation by the photosynthesis process

CH2O + O2

6.4  Hydrogen from Biorenewables via Biological Processes

169

anaerobic microorganisms are always involved, converting the organic compounds to organic acids, hydrogen and carbon dioxide. The advantages of the fermentative hydrogen production are the broad spectrum of applicable substrates as well as high hydrogen production yields (Nandi and Sengupta, 1998; Hawkes et al., 2002). Hydrogen production from the bacterial fermentation of sugars has been examined in a variety of reactor systems. Hexose concentration has a greater effect on H2 yields than the hydraulic retention time (HRT). Flocculation also was an important factor in the performance of the reactor (Van Kinkel and Logan, 2005). Anaerobic fermentation was conducted to improve hydrogen fermentation of food waste in a leaching-bed reactor by heat-shocked anaerobic sludge, and also to investigate the effect of dilution rate on the production of hydrogen and metabolites in hydrogen fermentation (Han and Shin, 2004). Direct photobiological hydrogen production by photosynthetic microorganisms is an active, developing field nowadays. Realization of technical processes for large-scale photobiological hydrogen production from water, using solar energy, would result in a major, novel source of sustainable, environmentally friendly and renewable energy. The unique biological process of photosynthesis in which solar energy is used to split water is combined with the natural capacity to combine obtained products into hydrogen, catalyzed by enzymes called hydrogenases. In nature, only cyanobacteria and green algae possess water oxidizing photosynthesis and hydrogen production, providing the option to form hydrogen from the Sun and water (Prince and Kheshgi, 2005; Viswanathan, 2006). An increase in the production of hydrogen from biomass-derived glucose and attainment of the maximum molar yield of hydrogen, can be achieved through the enzymes of the pentose phosphate cycle in conjunction with a hyperthermophilic hydrogenase. This process includes centers on three NADP+ (NADP+ to form NADPH, nicotinamide adenine dinucleotide phosphate) dependent enzymes, glucose-6 phosphate dehydrogenase (G6PDH), 6-phosphogluconate dehydrogenase (6PGDH) and hydrogenase from Pyrococcus furiosus. The dehydrogenases are currently obtained from mesophilic sources (Viswanathan, 2006). The enzymatic conversion of cellulosic waste to hydrogen via an in vitro enzymatic pathway involves the conversion of potential glucose sources such as cellulose by cellulases and plant sap (i.e., sucrose) by invertase and glucose isomerase to glucose. Glucose, the sugar produced by photosynthesis, is also renewable, unlike fossil fuels such as oil. The glucose substrate is then oxidized and the cofactor, NADP+ is simultaneously reduced. The presence of a pyridine-dependent hydrogenase in this system causes the regeneration and recycling of NAD(P)+ with the concomitant production of molecular hydrogen. The overall aim is to increase the production of hydrogen from biomass-derived glucose and achieve the maximum molar yield of hydrogen by employing the enzymes of the pentose phosphate pathway in conjunction with the hydrogenase from Pyrococcus furiosus. The main advantage over hydrogen production by fermentation is that close-to-theoretical yields of hydrogen from sugar would be possible (Das and Veziroglu, 2008; Viswanathan, 2006). Hydrogen is produced in microorganisms by enzymes capable of reducing free protons to molecular hydrogen. Examples of these enzymes include hydrogenases and the nitrogenases. The production of hydrogen by these enzymes is usually cou-

170

6  Biohydrogen

pled to some other biochemical processes. The energy used by these enzymes is usually in multiple steps from an organism’s central energy input and is provided in the form of electron carriers such as ferredoxin or NADPH and energy yielding molecules like ATP. Obtaining useful amounts of hydrogen from microorganisms will require increasing the efficiency of hydrogenases and overcoming other obstacles. One problem is that some hydrogenases and nitrogenases are inhibited by oxygen. Oxygen is produced by photosystem II (PSII) during oxygenic photosynthesis. The driving force for reaction energy can be obtained by the breaking of bonds (the multistep breakdown of glucose to generate ATP and CO2) or from electronic excitation. For example, plants, algae, cyanobacteria and photosynthetic bacteria can use light energy to raise electrons into higher energy states. In the case of plants, algae and cyanobacteria, the source of excitable electrons is water. The excited electrons are stripped from water, which then splits into oxygen and protons (Das and Veziroglu, 2008; Viswanathan, 2006).

6.4.1 Hydrogen Production via Microbial Fermentation of Biomass In microbial fermentation of biomass, different waste materials can be used as substrates. A new and unique process has been developed when substrates such as carbohydrates are fermented by a consortium of bacteria; they produce hydrogen and carbon dioxide. Highly concentrated organic wastewater is one of the most abundantly available biomasses, which can be exploited for microbial conversion into hydrogen (Nath and Das, 2003). Municipal solid wastes and digested sewage sludge have the potential to produce large amounts of hydrogen by suppressing the production of methane by introducing low voltage electricity into the sewage sludge. The substrate from the acidogenesis of fruit and vegetable market wastes gives higher hydrogen evolution rates (about threefold) compared to synthetic medium. A mixed culture of photosynthetic anaerobic bacteria provides a method of utilization of a variety of resources for biohydrogen production (Miyaka et al., 1990).

6.4.2 Anaerobic Hydrogen Production Anaerobic hydrogen production proceeds from photofermentation as well as without the presence of light. Anaerobic bacteria use organic substances as the sole source of electrons and energy, converting them into hydrogen. Glucose + 2H2O

→ 2Acetate + 2CO2 + 4H2

(6.3)

Glucose

→ Butyrate + 2CO2 +2H2

(6.4)

The reactions involved in hydrogen production (Eqs. 6.3 and 6.4) are rapid and these processes do not require solar radiation, making them useful for treating large quantities of wastewater by using a large fermenter.

6.4  Hydrogen from Biorenewables via Biological Processes

171

Since they cannot utilize light energy, the decomposition of organic substrates is incomplete. Further decomposition of the acetic acid is not possible under anaerobic conditions. Nevertheless, these reactions are still suitable for the initial steps of wastewater treatment and hydrogen production, followed by further waste treatment stages. A new fermentation process that converts valueless organic waste streams into hydrogen-rich gas has been developed by Van Ginkel et  al. (2001). The process employs mixed microbial cultures readily available in nature, such as compost, anaerobic digester sludge, soil, etc., to convert organic wastes into hydrogen-rich gas. The biodegradation efficiencies of the pollutants were examined by changing hydraulic retention time (HRT) as a main operating variable. An enriched culture of hydrogen-producing bacteria such as Clostridia was obtained by heat treatment, pH control and HRT control of the treatment system. The biohydrogen fermentation technology could enhance the economic viability of many processes utilizing hydrogen as a fuel source or as raw materials. Figure 6.2 shows the basic components of an anaerobic digestion system. Anaerobic fermentative microorganisms, cyanobacteria and algae are suitable in biological production of hydrogen via hydrogenase due to reversible hydrogenases (Adams, 1990). Cyanobacteria and algae can carry out photoevolution of hydrogen catalyzed by hydrogenases. The reactions are similar to electrolysis involving splitting of water into oxygen and hydrogen (Gaffron, 1940).

Fig. 6.2  Basic components of an anaerobic digestion system

172

6  Biohydrogen

Fig. 6.3  Schematic diagram of the two-stage reactor system

Hydrogen-producing bacteria (Clostridia) were found to have growth rates about five to ten times higher than that of methane-producing bacteria (Van Ginkel et al., 2001; Sung, 2004). In a continuous flow bioreactor system, hydrogen production showed a declining trend at the later stage of reactor operation. Based on these findings, it is hypothesized that Clostridia may have gone through a phenomenon known as “degeneration” in which they lose their ability to produce hydrogen. Therefore, inoculating fresh mixed cultures may be a feasible way to maintain a sustainable hydrogen production. Based on this hypothesis, a two-stage anaerobic reactor has been proposed. The first-stage reactor is designed as a hydrogen-producing reactor whereas the second-stage reactor will be employed to cultivate fresh seed culture to perpetually supply the first one. Figure 6.3 shows the schematic diagram of the two-stage reactor system. The hydrogen-producing reactor has a total volume of 5 l with active volume of 3 l. The second stage has a total volume of 22 l, and the active volume is 18 l (Sung, 2004).

6.4.3 Biophotolytic Hydrogen Production Biophotolysis is the action of light on biological systems that results in the dissociation of a substrate, usually water into molecular hydrogen and oxygen. Photosynthetic bacteria (e.g., Rhodobactor) can use broad organic substrates including lactic and acetic acids as the energy and carbon source under light irradiation. Photoautotrophic green microalgae and cyanobacteria use sunlight and carbon dioxide as the sole sources for energy and carbon.

6.4  Hydrogen from Biorenewables via Biological Processes

173

Cyanobacteria are potential microbial species for hydrogen production via direct biophotolysis. By using nitrogenase and/or bi-directional hydrogenase, both heterocystous nitrogen-fixing strains and unicellular non-nitrogen-fixing strains are able to evolve hydrogen under special conditions. Hydrogen production increased significantly when replacing the air with argon (Howarth and Codd, 1985; Lindblad et al., 2002). Under special conditions, the reducing equivalents (ferredoxin) can also be used by hydrogenase or nitrogenase to reduce protons for evolution of molecular hydrogen. Using Fe-hydrogenase and reduced ferredoxin is the substrate for hydrogen evolution. Anaerobic adaptation is needed for the cells to induce reversible Fe-hydrogenase. In order to overcome the inhibitive effect of oxygen on hydrogenase, various methods have been investigated with limited success, such as spatial separation of oxygen from hydrogen, immobilization of chloroplasts, electron carrier and hydrogenase, oxygen scavenging, and gas purging (Miura, 1995; Miura et al., 1997). A major cost factor in large-scale hydrogen production is the photobioreactor that is usually characterized by surface area for light irradiation (Benemann, 1997). A hydrogen productivity based on reactor surface area can be found from the volumetric productivity and a critical optical length. Photobiological production of hydrogen from water (biophotolysis) requires efficient biological converters, microalgae, and low-cost photobioreactors. Microalgal strains must be developed that exhibit high hydrogen production rates and photosynthetic efficiencies in dense cultures at full solar intensities. The photobioreactor must expose the hydrogen-producing cultures to sunlight, while allowing recovery of the gas. A preliminary analysis is presented of a two-stage process in which microalgae are cultivated in large open ponds to produce a high carbohydrate biomass that then produces hydrogen in tubular photobioreactors. Photobioreactors constructed of inexpensive, commercially available glass tubes are proposed for such applications. Photobiological hydrogen production requires long-term research and development (Benemann, 1997). Biological hydrogen production is often conducted in two stages under different atmospheric conditions, the first stage for cell growth followed by the second stage for hydrogen evolution. Nitrogen starvation is often applied at the end of the growth stage as an efficient metabolic stress to induce the activity of nitrogenase. The atmosphere plays an important role in hydrogen evolution by cyanobacteria and could be a cost factor in large-scale hydrogen production. A nitrogen-free gas phase such as argon plus carbon dioxide gives a high hydrogen evolution rate (Weissman and Benemann, 1977). Chlamydomonas reinhardtii, a facultative photoautotrophic and photohetero­ trophic microalga, is the representative of green microalgae for biohydrogen research (Tsygankov, 2006; White and Melis, 2006). Other algal species such as Chlorococcum littorale and Platymonas subcordiformis are also investigated for hydrogen evolution (Guan et al., 2004). Gaffron and Robins first observed that unicellular microalga Scenedesmus obliquus could either use hydrogen as an electron donor in carbon dioxide fixation or evolve hydrogen under anaerobic conditions in dark or light environments (Gaffron and Robins, 1942). Chlamydomonas reinhardtii evolves large quantities of hydrogen gas when deprived of sulfur (Vijayaraghavan and Soom, 2006).

174

6  Biohydrogen

6.4.4 Dark Fermentative Hydrogen Production Fermentative bacteria producing hydrogen may be cultivated in pure or mixed cultures selected from natural sources such as anaerobically digested sewage sludge or soil. The major pathways for microbial hydrogen production are driven by the anaerobic metabolism of pyruvate, formed during the catabolism of various substrates. Production of hydrogen by fermentation has been studied for a large group of pure fermentative bacteria, such as Clostridia. The biohydrogen production from bagasse based on dark fermentation was investigated using microorganisms like Bacillus licheniformis, Clostridium pasteurianum and Enterobacter cloacae (Vijayaraghavan and Soom, 2006). Dark fermentation is the fermentative conversion of organic substrate to biohydrogen, it is a complex process manifested by a diverse group of bacteria by a series of biochemical reactions involving three steps similar to anaerobic conversion. Dark fermentation differs from photofermentation because it proceeds without the presence of light. Dark fermentation for hydrogen production from wastes could be competitive with fossil fuel-derived hydrogen, providing a plausible approach to practical biohydrogen production. However, most of the research on biohydrogen production from organic wastes over the past two decades has focused on the use of photosynthetic bacteria (Sasikala et  al., 1993). Benemann (1998) concluded that the dark fermentation of wastes is a promising process for biohydrogen production. The biohydrogen from carbohydrates was investigated using hyper thermophilic bacteria based on dark anaerobic fermentation (Claassen et al., 1999) and a high-rate anaerobic trickling filter (Groenestijn et al., 2002). Scenedesmus, a green microalga, evolved molecular hydrogen under light conditions after being kept in anaerobic and dark conditions (Gaffron and Rubin, 1942). The responsible enzyme for hydrogen evolution is a reversible hydrogenase because it catalyzes the reaction in both directions (Mertens and Liese, 2004). Benemann and Weare (1974) reported that a nitrogen-fixing cyanobacterium, Anabaena cylindrica, evolved hydrogen and oxygen gas simultaneously in an argon atmosphere for several hours. The enzyme involved in hydrogen evolution is nitrogenase, which is responsible for the reduction of nitrogen into ammonia (Masukawa et al., 2002). In photosynthesis, the reduced carbon is stored as endogenous carbohydrates, such as starch in microalgae and glycogen in cyanobacteria (Dauvillee et al., 2006). Following Gaffron and Rubin’s discovery (Gaffron and Robins, 1942), studies on the mechanisms involved in hydrogen evolution have found that the electrons or reducing equivalents of hydrogenase and nitrogenase do not always come from water, but may sometimes originate from the intracellular energy reserve including carbohydrates (Miura et al., 1995; Antal and Lindblad, 2005). The algal fermentation conditions for the hydrogen production were investigated to improve the photobiological hydrogen production by a combination of a marine green alga Chlamydomonas sp. MGA161 and a marine photosynthetic bacterium Rhodopseudomonas sp. W-1S. The scaling-up of our biophotolysis system with algal-bacterial combination was carried out. The stably sustained starch accumulation and degradation

6.4  Hydrogen from Biorenewables via Biological Processes

175

in the algal cells and hydrogen photoproduction from algal fermentation products by photosynthetic bacteria occurred in an alternating light-dark cycle (Miura et al., 1995). The stored energy is released through fermentation of the endogenous carbohydrates in dark conditions, and the excess reducing power can be deposited by hydrogenase on protons forming molecular hydrogen (Gfeller and Gibbs, 1984). Hydrogen evolution from endogenous carbon reserve under dark anaerobic conditions looks very similar to the conventional anaerobic hydrogen fermentation, but the endogenous carbon reserve is made in vivo during photosynthesis. In this sense, the electrons or reducing equivalents in indirect biophotolysis are derived from water by photoautotrophic cells. This indirect biophotolysis, therefore, consists of two stages in series: photosynthesis for carbohydrate accumulation, and dark fermentation of the carbon reserve for hydrogen production. In this way, the oxygen and hydrogen evolutions are temporally and/or spatially separated (Benemann, 1996). Miura and co-workers proposed a process of hydrogen production via indirect biophotolysis by using natural light/dark cycles (Miura et  al., 1997). According to this proposal, carbon dioxide is reduced to starch by photosynthesis in daytime, and the starch thus formed, is fermented to hydrogen gas and organic acids under anaerobic conditions during nighttime. The organic acids and other fermentative products can be further used for hydrogen evolution by photosynthetic bacteria under light irradiation (Melis and Melnicki, 2006). Few studies have been conducted on fermentative hydrogen production by green microalgae. Compared with green microalgae, unicellular non-nitrogen-fixing cyanobacteria have attracted more research interest for hydrogen production via indirect biophotolysis. Spirulina platensis is a filamentous cyanobacterium cultivated at large commercial scales as a food supplement with high proteins, antioxidants and other nutrients. S. platensis NIES-46 accumulates high glycogen content (50% dry mass) in nitrogen-limited conditions and evolves molecular hydrogen at a moderate rate of 0.11 mmol/g dry wt/h after induction in dark and nitrogen atmosphere (Aoyama et al., 1987). For 1 mol of hydrogen evolved, the cells also release 1.4 mol of acetate, 0.65 mol of ethanol, 0.4 mol of formate and 0.1 mol of lactate as electron acceptors. A unicellular non-nitrogen-fixing cyanobacterium Gloeocapsa alpicola CALU743 showed a high activity of reversible hydrogenase induced in dark anaerobic conditions (Serebryakova et al., 1998). In dark fermentation, 1 mol glucose and the strain produces 3.92 mol of hydrogen, 1.83 mol of CO2, 1.97 mol of acetate, and small amounts of lactate and ethanol. The hydrogen yield is very close to the theoretical value when acetate is the sole fermentative product. The energy obtained in 4 mol of hydrogen is about 40% of the energy in 1 mol of glucose. The remainder of glucose energy is mainly left in 2 mol of acetic acid. The overall energy efficiency would therefore be significantly improved if acetate could be reused to form endogenous carbon reserve by facultative photoautotrophic cells in photosynthesis. Carbohydrates are the preferred organic carbon source for hydrogen-producing fermentations. Glucose in the biomass yielded 2 and 4 mol H2 per mol glucose with butyrate and acetic acid as their respective fermentation product. Hydrogen can be produced sustainably by anaerobic bacterial growth on carbohydrate-rich

176

6  Biohydrogen

substrates, giving organic fermentation end-products such as hydrogen and carbon dioxide. Microbial community composition dynamics was studied during hydrogen fermentation from glucose in a fluidized-bed bioreactor (FBR) aimed at obtaining insight into the hydrogen fermentation microbiology and factors resulting in the instability of biofilm processes. FBR hydrogen production performance was characterized by an instable pattern of the prompt onset of hydrogen production followed by a rapid decrease. Gradual enrichment of organisms increased the diversity of the FBR attached and suspended growth phase bacterial communities during the operation. A high glucose loading rate favored the hydrogen production by an Escherichia coli affiliated strain. Decrease in H2 production, associated with a shift from acetate–butyrate to acetate–propionate production, was due to changes in the FBR attached and suspended growth phase bacterial community compositions. During the shift, organisms, including potential propionate producers, were enriched in the communities while the proportion trend of C. butyricum decreased. Suggestions of reactions taking place during anaerobic, dark fermentation of glucose in the fluidized-bed bioreactor include (Koskinen et al., 2007): Ethanol formation: C6H12O6 → 2CH3CH2OH + 2CO2

(6.5)

Acetate formation: C6H12O6 + 4H2O → 2CH3COO– + 4H2 + 2HCO3– + 4H+

(6.6)

Propionate formation: C6H12O6 + 2H2 → 2CH3CH2COO– + 2H+ + 2H2O

(6.7)

Butyrate formation: C6H12O6 + 2H2O → CH3CH2CH2COO– + 2H2 + 2HCO3– + 3H+

(6.8)

6.5 Hydrogen from Biorenewables via Thermochemical Processes Hydrogen can be produced from biorenewable feedstocks via thermochemical conversion processes such as pyrolysis, gasification, steam gasification, steam reforming of bio-oils, and supercritical water gasification (SWG) of biomass. The strategy is based on producing hydrogen from biomass pyrolysis using a co-product strategy to reduce the cost of hydrogen. It has been suggested that only this strategy could compete with the cost of the commercial hydrocarbon-based technologies (Wang et al., 1998). This strategy will demonstrate how hydrogen and biofuel are economically feasible and can foster the development of rural areas when practiced on a larger scale. The process of biomass to activated carbon is an alternative route to hydrogen with a valuable co-product that is practiced commercially. The yield of hydrogen that can be produced from biomass is relatively low,

6.5  Hydrogen from Biorenewables via Thermochemical Processes

177

12–14% based on the biomass weight (Demirbas, 2005a). The proposed second process is fast pyrolysis of biomass to generate bio-oil and catalytic steam reforming of the bio-oil to hydrogen and carbon dioxide. In the pyrolysis and gasification processes, the water–gas shift is used to convert the reformed gas into hydrogen, and pressure swing adsorption is used to purify the product. The cost of hydrogen production from supercritical water gasification of wet biomass was several times higher than the current price of hydrogen from steam methane reforming (Demirbas, 2005a). The pyrolysis was carried out at moderate temperatures and steam gasification at the highest temperatures. The pyrolysis-based technology, in particular, because it has co-product opportunities, has the most favorable economics. The yield from steam gasification increases with increasing water-to-sample ratio. The yields of hydrogen from the pyrolysis and the steam gasification increase with increase of temperature. In general, the gasification temperature is higher than that of pyrolysis and the yield of hydrogen from the gasification is higher than that of the pyrolysis. The highest yields (% dry and ash-free basis) were obtained from the pyrolysis (46%) and steam gasification (55%) of wheat straw, while the lowest yields from olive waste. The yield of hydrogen from supercritical water extraction was considerably high (49% by volume) at lower temperatures. The catalytic aqueous phase reforming might prove useful for the generation of hydrogen-rich gas from carbohydrates extracted from renewable biomass and biomass waste streams. The biomass-derived hydrocarbons are suitable to hydrogen generation from biomass, as well as for the reforming. It is believed that in the future biomass can become an important sustainable source of hydrogen. Biomass has the advantage of low environmental impact compared with that for fossil fuels. The price of hydrogen obtained by direct gasification of lignocellulosic biomass, however, is about three times higher than that for hydrogen produced by steam reforming of natural gas (Spath et al., 2000). Hydrogen from organic wastes has generally been based on the following thermochemical reactions: 1. Production of hydrogen by pyrolysis of biomass Biomass → H2 + CO + CO2 + Hydrocarbon gases + Tar + Char

(6.9)

2. Production of hydrogen by catalytic steam gasification of biomass Biomass + H2O → H2 + CO2 + CO

(6.10)

3. Production of hydrogen by air gasification of biomass Biomass + H2O + Air → H2 + CO2 + CO + N2

(6.11)

Steam reforming is the major process for the production of hydrogen presently. This process has several disadvantages. For example, it is a thermally inefficient process (about 90% including the convection zone) and there are mechanical and maintenance issues. The process is difficult to control and reforming plants require a large capital investment. Hence to meet the increasing demand for this future fuel, alternatives to reforming processes are essential.

178

6  Biohydrogen

Biomass-derived synthesis gas can provide a renewable route to hydrogen. A novel bacterial process has been proposed as an alternative to the conventional high-temperature catalytic process for the production of hydrogen from synthesis gas via the water–gas shift (WGS) reaction. Hydrogen can be produced via pyrolysis or gasification of biomass resources such as agricultural residues like peanut shells, consumer wastes including plastics and waste grease, or biomass specifically grown for energy uses. Biomass pyrolysis produces a liquid product (bio-oil) that contains a wide spectrum of components that can be separated into valuable chemicals and fuels, including hydrogen.

6.5.1 Potential of Renewable Hydrogen Production Hydrogen is produced today dominantly from carbonaceous raw materials. Milne et al. (2002) reported approximately 95% of the hydrogen produced comes from fossil fuels conversion, such as natural gas reforming. With the growing concern about global climate changes, the currently used way of producing hydrogen will have to change, as CO2 carbon emission is always associated with such processes. Therefore alternative methodologies should be identified to overcome the shortage of this process. Using biomass as a hydrogen carrier in the near and mid-term appears viable in terms of technology, economy and environment as well as availability of sources. Even if without the subsequent sequestration of carbon, the whole process is still environment friendly as biomass is a CO2-neutral resource in the life cycle (Chen et al., 2003). Biomass has been considered as potential feedstock for gasification to produce syngas (H2 + CO). An alternative approach to the production of H2 from biomass begins with fast pyrolysis of biomass (Wang et al., 1997). Production of hydrogen gas by gasification of carbon with superheated steam was reported (Lower, 1963). The different methods of hydrogen production are: production from solid biomass (e.g., pellets of dedicated energy crops, waste biomass), fermentation of liquid manure and biological hydrogen production. The advantage of direct hydrogen production from biomass is that renewable energy sources can be utilized without the need of electrolysis thus leading to higher system efficiency and a more favorable overall result. Hydrogen can be extracted from hydrogen-rich biomass sources like wood chips and agricultural waste. Biomass is available and obtainable in the world through the rational collection of byproducts from agricultural and forestry industries. The potential supply of biomass is significantly large as an energy crop. Biomass can be used to produce hydrogen or hydrogen-rich gas via different technical pathways, i.e., anaerobic digestion, fermentation, metabolic processing, high-pressure supercritical conversion, gasification and pyrolysis. Compared with other pathways, gasification and pyrolysis appear technoeconomically viable at the current stage. A certain number of efforts have already been made to test gasification or pyrolysis of biomass for the production of hydrogen (Milne et al., 2002).

6.5  Hydrogen from Biorenewables via Thermochemical Processes

179

Those efforts can be categorized based on the types of biomass used, types of reactors (gasifiers or pyrolyzer), the addition of catalysts, end-products (e.g., hydrogen itself, hydrogen intermediates, hydrogen-rich gases) and gasifying medium used. The biomass types tested by previous researchers are residue coming from extraction of grass and lucern for protein, agricultural wastes (rice straw, wheat stalk), wood particles, municipal solid waste, almond shells, sawdust, black liquor, lignin, hazelnut shells, cotton and tobacco wastes, and plastic/rubber wastes (Demirbas et al., 1996; Caglar and Demirbas, 2002; Chen et al., 2003). The use of different catalysts such as dolomite, zeolites, potassium minerals, nickel-based compounds, platinum-based compounds, and metal oxides have been summarized in literature (Milne et  al., 2002; Chen et  al., 2002). As for the gasifying medium, the tested medium is steam, air, and oxygen. In addition, the gasification or pyrolysis process needs heating sources, and the used sources are electrical energy, combustion heat of fossil fuel or biomass char, solar energy, thermonuclear, and hydrothermal energy. Indirect pyrolysis of biomass to hydrogen through intermediates (pyrolysis oils) was also interestingly investigated (Chornet, 2001; Czernik et al., 2001).

6.5.2 Production of Hydrogen from Biomass via Pyrolysis Pyrolysis dates back to at least ancient Egyptian times, when tar for caulking boats and certain embalming agents were made by pyrolysis. In the 1980s, researchers found that the pyrolysis liquid yield could be increased using fast pyrolysis where a biomass feedstock is heated at a rapid rate and the vapors produced also condensed rapidly (Mohan et al., 2006). Pyrolysis is the thermal decomposition of organic matter occurring in the absence of oxygen or when significantly less oxygen is present than required for complete combustion. Pyrolysis is the basic thermochemical process for converting biomass to a more useful fuel. Biomass is heated in the absence of oxygen, or partially combusted in a limited oxygen supply, to produce a hydrocarbon-rich gas mixture, an oil-like liquid and a carbon-rich solid residue. The products of pyrolysis can be gaseous, liquid, and/or solid. Flash pyrolysis describes the rapid, moderate temperature (675–875 K) pyrolysis that produces liquids. Biomass is heated at rates of 100–10 000 K/s and the vapor residence time is normally less than 2 s. The oil products are maximized at the expense of char and gas. Pyrolysis is a process similar to gasification except generally optimized for the production of fuel liquids (pyrolysis oils) that can be used straight or refined for higher quality uses such as engine fuels, chemicals, adhesives, and other products. Pyrolysis typically occurs at temperatures in the range of 675 to 975 K. Pyrolysis and combustion of pyrolysis-derived fuel liquids and gases also produce the same categories of end-products as direct combustion of solids. Fast pyrolysis utilizes biomass to produce a product that is used both as an energy source and a feedstock for chemical production. Considerable efforts have been made to convert wood biomass to liquid fuels and chemicals since the oil cri-

180

6  Biohydrogen

sis in the mid-1970s. Most work has been performed on wood, because of its consistency and comparability between tests. However, nearly 100 types of biomass have been tested, ranging from agricultural wastes such as straw, olive pits, and nut shells to energy crops such as miscanthus and sorghum. The following are affected by the pyrolysis reaction rate and the yield of the volatiles: the biomass composition and structure, heating rate, residence time, catalyst, and particle size. Although very fast and very slow pyrolyses of biomass produce markedly different products, the variety of heating rates, temperatures, residence times, and feedstock varieties found in the literature make generalizations difficult to define, in regards to trying to critically analyze the literature (Mohan et al., 2006). Rapid heating and rapid quenching produced the intermediate pyrolysis liquid products, which condense before further reactions break down higher molecular weight species into gaseous products. High reaction rates minimize char formation. Under some conditions, no char is formed. At higher fast pyrolysis temperatures, the major product is gas. Many researchers have attempted to exploit the complex degradation mechanisms by conducting pyrolysis in unusual environments (Mohan et al., 2006). The main pyrolysis variants are listed in Table 6.1. Pyrolysis is the simplest and almost certainly the oldest method of processing one fuel in order to produce a better one. Pyrolysis can also be carried out in the presence of a small quantity of oxygen (gasification), water (steam gasification) and hydrogen (hydrogenation). Hydrogen from organic materials has generally been based on the following pyrolysis reactions (Demirbas and Arin, 2004; Demirbas, 2008a): Cellulose + H2O + Air

→ H2 + CO + CH4

(6.12)

Solid waste

→ CO +H2

(6.13)

Biomass + H2O + Air

→ H2 +CO2

(6.14)

If the purpose is to maximize the yield of liquid products resulting from biomass pyrolysis, a low-temperature, high heating rate, short gas residence time process would be required. For high char production, a low-temperature, low heating rate process would be chosen. If the purpose is to maximize the yield of fuel gas resulting from pyrolysis, a high-temperature, low heating rate, long gas residence time process would be preferred. It is believed that as the pyrolysis reaction progresses the carbon residue (semichar) becomes less reactive and forms stable chemical structures, and consequently the activation energy increases as the conversion level of biomass increases (Tran and Charanjit, 1978). Five biomass samples (hazelnut shell, cotton cocoon shell, tea factory waste, olive husk and spruce wood) were pyrolyzed in a laboratory-scale apparatus designed for the purpose of pyrolysis (Demirbas, 2001, 2002a). Figure 6.4 shows the simple experimental setup of pyrolysis. The main element of the experimental device is a vertical cylindrical reactor of stainless steel, 127.0 mm in height, 17.0 mm inner diameter and 25.0 mm outer diameter inserted vertically into an electrically heated tubular furnace and provided with an electrical heating system power source, with a heating rate of about 5  K/s. The biomass samples ground

6.5  Hydrogen from Biorenewables via Thermochemical Processes

181

Table 6.1  Pyrolysis methods and their variants Method

Residence time

Carbonation

Days

Conventional

5–30 min

Temperature, K

Heating rate

Products

675

Very low

Charcoal

875

Low

Oil, gas, char

0.5–5 s

925

Very high

Bio-oil

Flash-liquid

  523  K) starts already far below the desired reaction temperature (> 873 K) (Kruse et al., 2000). A schematic diagram of experimental apparatus of supercritical water gasification is depicted in Fig. 6.17. Supercritical water is a promising reforming media for the direct production of hydrogen at 875–1075  K temperatures with a short reaction time between 2 and 6 s. In addition to being a high mass transfer effect, supercritical

204

6  Biohydrogen

T

Mix pt.

T

Tubular reactor Ethanol

Water preheater HPLC pumps

Water

Water-cooled heat exchanger

P

Back pressure regulator

Tube furnace with temperature controller

Gas flow totalization

Data analysis with software

GC with TCD

Data acquisition system

6-port injection valve for online sampling

Gas flow meter

Gas-Liquid separator TOC analyzer for liquid phase

Fig. 6.17  Schematic diagram of experimental apparatus of supercritical water gasification

Table 6.9  Typical product yield (% by vol.) distributions for experiments with and without Ru/Al2O3 catalyst at 973 K with 1 wt.% glucose feed (15.9 g of catalyst/g mol of glucose) H2

CO2

CH4

CO

Direct reforming

54.5

31.4

8.5

5.6

Catalytic reforming

68.9

29.8

1.3

0.1

water also participates in the reforming reaction. The molecules in the supercritical fluid have high kinetic energy like the gas and high density like the liquid. Therefore, it is expected that the chemical reactivity can be high. In addition, the ionic product and dielectric constant of supercritical water, which are important parameters for chemical reactions, can be continuously controlled by regulating pressure and temperature. Pressure has a negligible effect on the hydrogen yield above the critical pressure of water (Gadhe and Gupta, 2007). As the temperature is increased from 875 to 1075 K the H2 yield increases from 53 to 73% by volume, respectively. Only a small amount of hydrogen is formed at low temperatures, indicating that direct reformation reaction of ethanol as a model compound in SCW is favored at high temperatures (> 975 K). With an increase in the temperature, the hydrogen and carbon dioxide yields increase, while the methane yield decreases. The water excess leads to a preference for the formation of hydrogen and carbon dioxide instead of carbon monoxide. The formed intermediate carbon monoxide reacts with water to hydrogen and carbon dioxide. The low carbon monoxide yield indicates that the water–gas shift reaction approaches completion (Byrd et al., 2007).

6.5  Hydrogen from Biorenewables via Thermochemical Processes

205

Thermochemical gasification of biomass has been identified as a possible system to produce renewable hydrogen with less dependence on exhaustible fossil energy resources. Compared with other biomass thermochemical gasifications, such as air gasification or steam gasification, the SCWG has high gasification efficiency at lower temperatures and can deal directly with wet biomass without drying (Yan et al., 2006). The capillaries (1mm ID and 150 mm length tubular reactors) are heated rapidly (within 5 s) in a fluidized sand bed to the desired reaction temperature. Experimentation with the batch capillary method has revealed that, especially at low temperatures and high feed concentrations, char formation occurs. A fluidized-bed reactor might be a good alternative to solve the problems related to this char and ash formation (Kruse et al., 2000). To study the effect of the Ru/Al2O3 catalyst on hydrogen yield for reforming of glucose in supercritical water, the experiments were compared to reactions with and without catalytic runs under identical conditions. Typical product distributions are shown in Table 6.9 for experiments with and without a Ru/Al2O3 catalyst at 973 K with 1 wt.% glucose feed (Byrd et  al., 2007). There was a significant reduction in carbon monoxide and methane yields in the presence of the catalyst. The main products of the reaction were hydrogen, methane, carbon dioxide, and carbon monoxide. The low carbon monoxide yield (0.1% by vol.) indicates that the water–gas shift reaction approaches completion. Cellulose and sawdust were gasified in supercritical water to produce hydrogenrich gas, and Ru/C, Pd/C, CeO2 particles, nano-CeO2 and nano-(CeZr)xO2 were selected as catalysts. The experimental results showed that the catalytic activities were Ru/C > Pd/C > nano-(CeZr)xO2 > nano-CeO2 > CeO2 particle in turn. The 10 wt.% cellulose or sawdust with CMC can be gasified almost completely with a Ru/C catalyst to produce 2–4 g hydrogen yield and 11–15 g potential hydrogen yield per 100 g feedstock at the condition of 773 K, 27 MPa, 20 min residence time in supercritical water (Hao et al., 2005). Catalysts for low-temperature gasification include combinations of stable metals, such as ruthenium or nickel bimetallics and stable supports, such as certain titania, zirconia, or carbon. Without catalyst the gasification is limited (Kruse et al., 2000). Sodium carbonate is effective in increasing the gasification efficiency of cellulose (Minowa et al., 1997). Likewise, homogeneous, alkali catalysts have been employed for high-temperature supercritical water gasification. The yields of hydrogen from steam gasification increase from 29 to 45% for (water/solid) = 1 and from 29 to 47% for (water/solid) = 2 with increasing of temperature from 975 to 1225  K. Figure 6.18 shows comparisons for the yield of hydrogen from supercritical fluid extraction (SFE), pyrolysis and steam gasification (water/solid = 2) of beech wood at different temperatures. Distilled water was used in the SFE (the critical temperature of pure water is 647.7 K). From Fig. 6.18, the yield of hydrogen from SFE was considerably high (49%) at lower temperatures. The pyrolysis was carried out at moderate temperatures and steam gasification at the highest temperatures (Demirbas, 2006a).

206

6  Biohydrogen

50 Yield of hydrogen, vol.%

45 40 35 30 Supercritical fluid extraction Conventional pyrolysis

25 20 15 10 600

Steam gasification 700

800 900 1000 1100 1200 Temperature, K

Fig. 6.18  Plots for yield of hydrogen from supercritical fluid (water) extraction, pyrolysis and steam gasification (water/solid = 2) of beech wood at different temperatures

6.5.7.1 Advantages of Supercritical Water The reforming in supercritical water (SCW) offers several advantages over the conventional technologies because of the unusual properties of supercritical water. The density of supercritical water is higher than that of steam, which results in a high space-time yield. The higher thermal conductivity and specific heat of supercritical water is beneficial for carrying out the endothermic reforming reactions (Gadhe and Gupta, 2007). In the supercritical region, the dielectric constant of water is much lower. Further, the number of hydrogen bonds is much smaller and their strength is considerably weaker. As a result, SCW behaves as an organic solvent and exhibits extraordinary solubility toward organic compounds containing large non-polar groups and most permanent gases (Demirbas, 1998; Byrd et  al., 2007). Another advantage of SCW reforming is that the H2 is produced at a high pressure, which can be stored directly, thus avoiding the large energy expenditures associated with its compression. The SCWG process becomes economical as the compression work is reduced owing to the low compressibility of liquid feed when compared to that of gaseous H2 (Byrd et al., 2007).

6.5.8 Hydrogen-rich Gas from Shells via Supercritical Water Extraction Agricultural shell samples (walnut, almond, hazelnut cotton cocoon, and sunflower shells) were subjected to supercritical water extraction for producing hydrogen-rich gas mixtures (Demirbas, 2004). Table 6.10 shows structural analysis results of the shell samples. In a typical run of this study, the autoclave was loaded with a 5.0 g

6.5  Hydrogen from Biorenewables via Thermochemical Processes

207

sample and 50–70 g of deionized water. The supercritical fluids extraction (SFE) parameters were adjusted as follows: the temperatures for supercritical water runs were 650 ± 3, 670 ± 3, 690 ± 3, 710 ± 3, 730 ± 3 and 750 ± 3 K, and pressures measured were 23.2, 25.4, 28.0, 32.5 and 38.7 MPa. Figure 6.19 shows the plots for yields of hydrogen from supercritical water extraction of shell samples versus temperature. The yields of hydrogen from supercritical water extraction increase with increasing extraction temperatures. The yield of hydrogen from almond shell increases from 6.7 to 13.5% with the temperature increase from 650 to 750 K, respectively (Demirbas, 2004). Figure 6.20 shows the plots for yields of hydrogen from supercritical water extraction of shell samples versus cellulose content at different temperatures. The yields of hydrogen from supercritical water extraction increase with increasing cellulose contents of the shell samples (Demirbas, 2004). Table 6.10  Structural analyses results of shell samples (wt.% of dry, ash and extractive-free basis) Sample of shell

Hemicellulose

Cellulose

Lignin

Almond

29.6 ± 2.8

52.0 ± 5.6

20.9 ± 2.1

Cotton cocoon

10.5 ± 1.1

33.5 ± 3.5

50.0 ± 5.3

Hazelnut

31.4 ± 3.2

27.7 ± 2.9

44.4 ± 4.7

Sunflower

35.6 ± 3.8

49.7 ± 5.2

17.5 ± 1.9

Walnut

22.7 ± 2.3

26.3 ± 2.8

53.8 ± 5.7

Yield of hydrogen, wt% of dry basis

14

12

Almond shell Cotton cocoon shell Hazelnut shell Sunflower shell Walnut shell

10

8

6

4 640

660

680

720 700 Temperature, K

740

760

Fig. 6.19  Plots for yields of hydrogen from supercritical water extraction of shell samples versus temperature

208

6  Biohydrogen

From 293 K to 650 K From 293 K to 670 K From 293 K to 690 K From 293 K to 710 K From 293 K to 730 K From 293 K to 750 K

Yield of hydrogen, wt% of dry basis

14

12

10

8

6

4

25

30

35 40 45 50 Cellulose content, wt% of dry basis

55

Fig. 6.20  Plots for yields of hydrogen from supercritical water extraction of shell samples versus cellulose content at different temperatures

6.5.9 Production of Hydrogen from Mosses and Algae via Pyrolysis and Steam Gasification Most studies concerning mosses have been taxonomic and medical. Some species of Bryophytes, such as Atricum, Dicranum, Mnium, Polytrichum, and Sphagnum, are important for the economy. Approximately 200 million tons of peat formed from Sphagnum per year is used as a fuel in the world (Cetin and Yurdakulol, 1985, 1988). The chemical compositions of algae are given in Table  6.11 (Demirbas, 2007). Algae were mainly composed of proteins, lipids and water-soluble carbo­ hydrates. Two moss samples (Polytrichum commune, Thuidium tamariscinum), one alga sample (Cladophora fracta), and one microalga sample (Chlorella protothecoides) were subjected to pyrolysis and steam gasification for producing hydrogen-rich gas (Demirbas, unpublished work). The temperature of the reaction vessel was measured with an iron-constantan thermocouple and controlled at ±3 K. The pyrolysis experiments were performed at temperatures of 575, 625, 675, 725, 775, 825 and 925 K. The steam gasification experiments were carried out at temperatures of 825, 875, 925, 975, 1025, 1075, 1125, 1175 and 1225 K (Demirbas, unpublished work). Table 6.12 shows the proximate analysis data and higher heating values (HHV) of samples. The HHV (MJ/kg) of the moss and alga samples as a function of fixed carbon (FC), wt.% can be calculated from: HHV = 0.322 (FC) + 10.7123

(6.37)

6.5  Hydrogen from Biorenewables via Thermochemical Processes

209

Table 6.11  Chemical compositions of algae on a dry matter basis (%) Species of sample

Proteins

Carbohydrates

Lipids

Nucleic acid

Scenedesmus obliquus

50–56

10–17

12–14

3–6

Scenedesmus quadricauda

47

 –

  1.9

–

Scenedesmus dimorphus

  8–18

21–52

16–40

–

Chlamydomonas rheinhardii

48

17

21

–

Chlorella vulgaris

51–58

12–17

14–22

4–5

Chlorella pyrenoidosa

57

26

 2

–

Spirogyra sp.

  6–20

33–64

11–21

–

Dunaliella bioculata

49

 4

 8

–

Dunaliella salina

57

32

 6

–

Euglena gracilis

39–61

14–18

14–20

–

Prymnesium parvum

28–45

25–33

22–38

1–2

Tetraselmis maculata

52

15

 3

–

Porphyridium cruentum

28–39

40–57

  9–14

–

Spirulina platensis

46–63

  8–14

  4–9

2–5

Spirulina maxima

60–71

13–16

  6–7

3–4.5

Synechoccus sp.

63

15

11

5

Anabaena cylindrica

43–56

25–30

  4–7

–

Table 6.12  Proximate analysis data and higher heating values (HHV) of samples (wt.% dry basis) Sample

Fixed carbon

Volatile matter

Ash

HHV (MJ/kg)

Polytrichum commune

19.4

65.8

14.8

17.0

Thuidium tamarascinum

15.4

72.3

12.3

15.5

Cladophora fracta

28.1

65.6

  6.3

19.8

Chlorella protothecoides

39.6

54.6

  5.8

23.6

The HHVs can be calculated using Eq. 6.37 and represent high correlation obtained by means of regression analysis. The correlation coefficient r is 0.999. The yields of bio-oil from the samples via pyrolysis are presented as a function of the temperature (K) in Fig. 6.21. The yield of bio-oil from pyrolysis of the samples increased with temperature, as expected. The yields were increased up to 750 K in order to reach the plateau values at 775 K. The maximum yields for Polytrichum commune, Thuidium tamarascinum, Cladophora fracta and Chlorella protothecoides were 31.6, 37.3, 45.0 and 50.8% of the sample at 925 K, respectively. The bio-oil yields of pyrolysis from algae were higher than those of mosses. Bio-

210

PC

TT

CF

CP

55 45 Yield of bio-oil, wt%

Fig. 6.21  Plots for yield of bio-oil from moss and alga samples by pyrolysis at different temperatures (K). Polytrichum commune (PC), Thuidium tamarascinum (TT), Cladophora fracta (CF), and Chlorella protothecoides (CP)

6  Biohydrogen

35 25 15 5 550

550

550

550

550

Temperature, K

PC

Yield of gaseous products, wt%

Fig. 6.22  Plots for yields of gaseous products from the samples by pyrolysis. Polytrichum commune (PC), Thuidium tamarascinum (TT), Cladophora fracta (CF), and Chlorella protothecoides (CP)

TT

CF

CP

40

30

20

10

0 550 600 650 700 750 800 850 900 Temperature, K

oil comparable to fossil oil was obtained from microalgae (Miao and Wu, 2004). In the pyrolysis process, the yield of charcoal decreases with increasing pyrolysis temperature. The yield of the liquid product is highly excessive at temperatures between 625 and 725 K. The HHVs for bio-oils from mosses 21.5–24.8  MJ/kg and the HHVs for biooils from alga and microalga 32.5 and 39.7 MJ/kg, respectively, were obtained by pyrolysis at temperatures ranging from 775 to 825 K. In general, algae bio-oils are higher quality than bio-oils from mosses. Figure 6.22 shows the effect of temperature on yields of gaseous products from the samples by pyrolysis. As can be seen in Fig. 6.22, the yields of gaseous products from the samples of Polytrichum commune, Thuidium tamarascinum, Cladophora fracta and Chlorella protothecoides increased from 5.3 to 40.6%, 6.5 to 42.2%, 8.2

6.5  Hydrogen from Biorenewables via Thermochemical Processes

50

Yield of hydrogen, % by vol

Fig. 6.23  Plots for yields of hydrogen in gaseous products from the samples by pyrolysis. Polytrichum commune (PC), Thuidium tamarascinum (TT), Cladophora fracta (CF), and Chlorella protothecoides (CP)

PC

CF

CP

40 35 30 25

60

Yield of hydrogen, % by vol

TT

45

20 625

Fig. 6.24  Plots for yields of hydrogen in gaseous products from the samples by steam gasification. Polytrichum commune (PC), Thuidium tamarascinum (TT), Cladophora fracta (CF), and Chlorella protothecoides (CP)

211

725 825 Temperature, K

PC

TT

CF

CP

1000 1100 Temperature, K

1200

50

40

30

20 800

900

to 39.2% and 9.5 to 40.6% by volume, respectively, while the final pyrolysis temperature was increased from 575 to 875 K. Figure 6.23 shows the plots for yields of hydrogen in gaseous products from the samples by pyrolysis. The percentage of hydrogen in gaseous products from the samples of Polytrichum commune, Thuidium tamarascinum, Cladophora fracta and Chlorella protothecoides increased from 21.3 to 38.7%, 23.0 to 41.3% and 25.8 to 44.4% and 27.6 to 48.7% by volume, respectively, while the final pyrolysis temperature was increased from 650 to 875 K. Figure 6.24 shows the plots for yields of hydrogen in gaseous products from the samples by steam gasification. The percentage of hydrogen in gaseous products from the above-mentioned samples increased from 21.8 to 50.0%, 23.5 to 52.0%,

212

6  Biohydrogen

CP (Present study)

BW (Ref. [16])

SW

50

Yield of hydrogen, % by vol

45

40

35

30

25 625

625

625 625 Temperature, K

625

625

Fig. 6.25  Plots for yields of hydrogen in gaseous products from microalga and wood samples by pyrolysis. Chlorella protothecoides (CP), beech wood (BW) and spruce wood (SW)

26.3 to 54.7% and 28.1 to 57.6% by volume, respectively, while the final gasification temperature was increased from 825 to 1225 K. Figure 6.25 shows the yields of hydrogen in gaseous products from microalga and wood samples by pyrolysis. The hydrogen in gaseous products from the samples of beech wood and spruce wood increased from 31.5 to 40.5% and 33.3 to 42.3% by volume, respectively, while the final pyrolysis temperature was increased from 650 to 875 K (Demirbas and Arin, 2004). Microalgae gaseous products are higher quality than gaseous products from wood (Fig. 6.25). In general, algae gaseous products are higher quality than gaseous products from mosses. Table 6.13 shows the yields of bio-oil by pyrolysis from moss and alga samples (Demirbas, 2006b). As can be seen from Table 6.13, the bio-oil yield for Chlorella protothecoides (a microalga sample) rose from 12.8 to 55.3% as the temperature rose from 575 to 775  K, and then gradually the percentage decreased to 51.8%, obtained at 875 K with a heating rate of 10 K/s. The bio-oil yield for Polytrichum commune (a moss sample) rose from 10.3 to 39.1% as the temperature rose from 575 to 775 K, and then decreased to 36.7% obtained at 875 K with a heating rate of 10 K/s (Demirbas, 2006b). For alga, maximum bio-oil yields of between 48.2 and 46.8%, and for microalga 55.3 and 53.7% were obtained at temperatures ranging from 775 to 825 K, whereas for wood, cotton stalk, tobacco stalk and sunflower bagasse, maximum oil yields between 39.7 and 49.4% were obtained at temperatures in the range from 775 to 825 K (Putun, 2002; Gercel, 2002).

6.5  Hydrogen from Biorenewables via Thermochemical Processes

213

Table 6.13  Yields of bio-oil by pyrolysis from moss and alga samples at different temperatures (K) Sample

575

625

675

725

775

825

875

Polytrichum commune

10.3

20.0

27.5

35.8

39.1

38.4

36.7

Dicranum scoparium

  6.0

15.5

21.8

30.7

34.3

33.8

31.7

Thuidium tamarascinum

  5.6

14.2

20.7

29.5

33.6

33.4

31.3

Sphagnum palustre

  7.9

17.7

25.3

33.5

37.0

36.3

34.6

Drepanocladus revolvens

  6.7

16.4

23.5

31.7

35.4

34.7

32.9

Cladophora fracta

10.5

23.5

33.2

43.4

48.2

46.8

44.6

Chlorella protothecoides

12.8

27.4

38.4

50.2

55.3

53.7

51.6

Table 6.14  Yields of gaseous product by pyrolysis from moss and alga samples at different temperatures (K) Sample

575

625

675

725

775

825

875

Polytrichum commune

6.5

14.8

22.6

26.4

29.2

36.6

42.2

Dicranum scoparium

5.8

12.5

19.8

25.0

27.6

35.0

40.8

Thuidium tamarascinum

5.3

11.2

17.9

23.5

25.6

33.2

39.3

Sphagnum palustre

5.5

11.9

18.3

24.2

26.5

34.0

39.8

Drepanocladus revolvens

5.6

12.3

18.9

24.7

27.0

34.5

40.4

Cladophora fracta

8.2

19.7

28.2

32.6

35.7

38.0

39.7

Chlorella protothecoides

9.5

21.8

29.5

33.7

36.3

38.1

39.5

Table 6.14  shows the yields of gaseous product by pyrolysis from moss and alga samples (Demirbas, 2006b). From Table 6.14, the yields of gaseous products for Chlorella protothecoides increased from 9.5 to 39.5% as the temperature rose from 575 to 875 K. The char yields of pyrolysis from mosses were higher than those of algae. With the interaction of water and char from decomposition of biomass, intermediate products are known to occur which leads to more hydrogen-rich gas yield by the steam reforming process. The pyrolysis was carried out at the moderate temperatures and steam gasification at the highest temperatures. In order to clarify the steam gasification mechanism in detail, more kinetic study is necessary. These results suggest that fundamental information obtained in the gasification of each component could possibly be used to predict the composition of product gas generated in air–steam gasification of biomass.

214

6  Biohydrogen

Summary Biohydrogen is a renewable biofuel produced from biorenewable feedstocks by a variety of methods, including chemical, thermochemical, biological, biochemical, and biophotolytical methods. The topic of biohydrogen touches on energy security, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sectors of all countries in the world. It is also an environmentally friendly alternative automotive fuel that can be used in an internal combustion engine. There are three types of microorganisms that produce hydrogen: cyanobacteria, anaerobic bacteria, and fermentative bacteria. The cyanobacteria directly decompose water to hydrogen and oxygen in the presence of light by photosynthesis. Photosynthetic bacteria use organic substrates like organic acids, whereas anaerobic bacteria use organic substances as the sole source of electrons and energy, converting them into hydrogen. A promising method is the biological production of hydrogen by fermentation. Fermentative hydrogen production is the fermentative conversion of organic substrates to biohydrogen. This process is manifested by a diverse group of bacteria using multienzyme systems involving three steps similar to anaerobic conversion. Hydrogen can be produced from biorenewable feedstocks via thermochemical conversion processes such as pyrolysis, gasification, steam gasification, steam reforming of bio-oils, and supercritical water gasification (SWG) of biomass. Comparison with other biomass thermochemical gasification such as air gasification or steam gasification, the supercritical water gasification (SCWG) can directly deal with the wet biomass without drying, and has high gasification efficiency in relatively lower temperatures. The cost of hydrogen production from supercritical water gasification of wet biomass was several times higher than the current price of hydrogen from steam methane reforming. Biomass is gasified in supercritical water at a series of temperatures and pressures during different resident times and the product gas is composed of H2, CO2, CO, CH4, and a small amount of C2H4 and C2H6.

References Adams, M.W.W. 1990. The structure and mechanism of iron-hydrogenases. Biochim Biophys Acta 1020:115–145. Aiba, S., Humphrey, A.E., Milis, N.F. 1973. Biochemical engineering, 2nd edn. Academic, New York. Akkerman, I., Janssen, M., Rocha, J., Wijffels, R.H. 2002. Photobiological hydrogen production: photochemical efficiency and bioreactor design. Int J Hydrogen Energy 27:1195–1208. Aoyama, K., Uemura, I., Miyake, J., Asada, Y. 1987. Fermentative metabolism to produce hydrogen gas and organic compounds in a cyanobacterium Spirulina platensis. J Ferment Bioeng 83:17–20. Antal, M.J. 1978. Tower power: producing fuels from solar energy, in Toward a solar civilization, R.H. Williams (Ed.) MIT Press, Cambridge, MA.

References 

215

Antal, M.J., Feber, R.C., Tinkle, M.C. 1974. Proceedings 1st World Hydrogen Energy Conference, Miami Beach, FL. Antal, M.J., Allen, S., Schulman, D., Xu, X., Divilio, R. 2000. Biomass gasification in supercritical water. Ind Chem Eng Res 39:4040–4053. Antal, T.K., Lindblad, P. 2005. Production of H2 by sulphur-deprived cells of the unicellular cyanobacteria Gloeocapsa alpicola and Synechocystis sp. PCC 6803 during dark incubation with methane or at various extracellular pH. J Appl Microbiol 98:114–120. Backman, R., Fredrick, W.J., Hupa, M. 1993. Basic studies on black-liquor pyrolysis and char gasification. Biores Technol 46:153–158. Benemann, J.R. 1996. Hydrogen biotechnology: progress and prospects. Nature Biotechnol 14:1101–1103. Benemann, J.R. 1997. Feasibility analysis of photobiological hydrogen production. Int J Hydrogen Energy 22:979–987. Benemann, J.R. 1998. The technology of biohydrogen. Plenum, New York. Benemann, J.R., Weare, N.M. 1974. Hydrogen evolution by nitrogen-fixing. Anabaena cylindrica cultures. Science 184:174–175. Byrd, A.J., Pant, K.K., Gupta, R.B. 2007. Hydrogen production from glucose using Ru/Al2 O3 catalyst in supercritical water. Ind Eng Chem Res 46:3574–3579. Caglar, A., Demirbas, A. 2002a. Hydrogen-rich gas mixture from olive husk via pyrolysis. Energy Convers Manage 43:109–117. Caglar, A., Demirbas, A. 2002b. Conversion cotton cocoon shell to hydrogen-rich gaseous products by pyrolysis. Energy Convers Manage 43:489–497. Cetin, B., Yurdakulol, E. 1985. Gerede-Aktas (Bolu) ormanlarinin karayosunlari (Musci) florasi. Doga Bilim Der 9:29–38 (in Turkish). Cetin, B., Yurdakulol, E. 1988. Yedigoller milli parkinin karayosunu florasi. Turkish J Bot 12:128– 146 (in Turkish). Chen, G., Spliethoff, H., Yang, L.B., Andries, J. 2003. Hydrogen production from gasification: pyrolysis of biomass. III. International Slovak Biomass Forum, Bratislava, Slovakia, 3–4 Feb 2003. Chornet, E. 2001. Biomass to hydrogen via fast pyrolysis and catalytic steam reforming. Proceedings of the 2001 USA. DOE Hydrogen Program Review (NREL/CP 570-30535). Claassen, P.A.M., Lier, J.B.V., Lopez, C.A.M., Niel, E.W.J., Sijitsma, L., Stams, A.J.M., Vriess, S.S.D., Weusthusis, R.A. 1999. Utilization of biomass for the supply of energy carries. Appl Microbiol Biotechnol 52:741–755. Cortright, R.D., Davda, R.R., Dumesic, J.A. 2002. Hydrogen from catalytic reforming of biomassderived hydrocarbons in liquid water. Nature 418:964–967. Cox, J.L., Tonkovich, A.Y., Elliott, D.C., Baker, E.G., Hoffman, E.J. 1995. Hydrogen from biomass: a fresh approach. Proceedings of the 2nd Biomass Conference of the Americas (NREL/ CP-200-8098; CONF-9508104) August 1995, Portland, Oregon. Czernik, S., French, R., Feik, C., Chornet, E. 2001. Production of hydrogen from biomass derived liquids. Proceedings of the 2001 USA. DOE Hydrogen Program Review (NREL/CP 57030535). Das, D., Veziroglu, T.N. 2008. Advances in biological hydrogen production processes. Int J Hydrogen Energy 33:6046–6057. Demirbas, A. 1998. Yields of oil products from thermochemical biomass conversion processes. Energy Convers Manage 39:685–690. Demirbas, A. 2000. Mechanisms of liquefaction and pyrolysis reactions of biomass. Energy Convers Manage 41:633–646. Demirbas, A. 2001. Yields of hydrogen of gaseous products via pyrolysis from selected biomass samples. Fuel 80:1885–1891. Demirbas, A. 2002a. Gaseous products from biomass by pyrolysis and gasification: effects of catalyst on hydrogen yield. Energy Convers Manage 43:897–909. Demirbas, A. 2002b. Hydrogen production from biomass by gasification process. Energy Sources 24:59–68.

216

6  Biohydrogen

Demirbas, A. 2004. Hydrogen-rich gas from fruit shells via supercritical water extraction. Int J Hydrogen Energy 29:1237–1243. Demirbas, A. 2005a. Hydrogen production via pyrolytic degradation of agricultural residues. Energy Sources 27:769–775. Demirbas, A. 2005b. Hydrogen production from biomass via supercritical water extraction. Energy Sources 27:1409–1417. Demirbas, M.F. 2006a. Hydrogen from various biomass species via pyrolysis and steam gasification processes. Energy Sources Part A 28:245–252. Demirbas, A. 2006b. Oily products from mosses and algae via pyrolysis. Energy Sources Part A 28:933–940. Demirbas, A. 2007. Production of biofuels from macroalgae and microalgae. Energy Edu Sci Technol 18:59–65. Demirbas, A. 2008a. Biohydrogen generation from organic wastes. Energy Sources Part A 30:475–482. Demirbas, A. 2008b. Hydrogen production from carbonaceous solid wastes by steam reforming. Energy Sources Part A 30:924–931. Demirbas, A., Arin, G. 2004. Hydrogen from biomass via pyrolysis: relationships between yield of hydrogen and temperature. Energy Sources 26:1061–1069. Demirbas, A., Karslioglu, S., Ayas A. 1996. Hydrogen resources: conversion of black liquor to hydrogen-rich gaseous products. Fuel Sci Technol Int 14:451–465. Demirbas A., Caglar, A. 1998. Catalytic reforming of biomass and heavy oil residues to hydrogen. Energy Edu Sci Technol 1:45–52. Demirbas, A., Arin, G. 2004. Hydrogen from biomass via pyrolysis: relationships between yield of hydrogen and temperature. Energy Sources 26:1061–1069. Dauvillee, D., Chochois, V., Steup, M., Haebel, S., Eckermann, N., Ritte, G., Ral, J.P., Colleoni, C., Hicks, G., Wattebled, F., Deschamps, P., D‘hulst, C., Lienard, L., Cournac, L., Putaux, J.L., Dupeyre, D., Ball, S.G. 2006. Plastidial phosphorylase is required for normal starch synthesis in Chlamydomonas reinhardtii. Plant J 48:274–285. Feng, W., van der Kooi, H.J., Arons, J.D.S. 2004. Biomass conversions in subcritical and supercritical water: driving force, phase equilibria, and thermodynamic analysis. Chem Eng Proc 43:1459–1467. Friedrich, K., Kordesch, K., Simader, G., Selan, M. 1995. The process cycle sponge-iron/hydrogen/iron oxide used for fuel conditioning in fuel cells. Proceedings of International Symposium on Fuel Cell System, New York. Gadhe, J.B., Gupta, R.B. 2007. Hydrogen production by methanol reforming in supercritical water: catalysis by in situ-generated copper nanoparticles. Int J Hydrogen Energy 32:2374–2381. Gaffron, H. 1939. Reduction of carbon dioxide with molecular hydrogen in green algae. Am J Bot 27:273–283. Gaffron, H. 1940. Carbon dioxide reduction with molecular hydrogen in green algae. Am J Bot 27:273–283. Gaffron, H., Rubin, J. 1942. Fermentative and photochemical production of hydrogen in algae. J Gen Physiol 26:219−240. Gercel, H.F. 2002. The effect of a sweeping gas flow rate on the fast pyrolysis of biomass. Energy Sources 24:633–642. Gest, H., Kamen, M.D. 1949a. Studies on the metabolism of photosynthetic bacteria; photochemical production of molecular hydrogen by growing cultures of photosynthetic bacteria. J Bacteriol 58:239–245. Gest, H., Kamen, M.D. 1949b. Photoproduction of molecular hydrogen by Rhodospirillum rubrum. Science 109:558–559. Gest, H., Blankenship, R.E. 2004. Time line of discoveries: anoxygenic bacterial photosynthesis. Photosynthesis Res 80:59–70. Gfeller, R.P., Gibbs, M. 1984. Fermentative metabolism of Chlamydomonas reinhardtii: I. Analysis of fermentative products from starch in dark-light. Plant Physiology 75:212–218.

References 

217

Groenestijn, J.W.V., Hazewinkel, J.H.O., Nienoord, M., Bussmann, P.J.T. 2002. Energy aspects of biological hydrogen production in high rate bioreactors operated in the thermophilic temperature range. Int J Hydrogen Energy 27:1141–1147. Guan, Y.F., Deng, M.C., Yu, X.J., Zhang, W. 2004. Two-stage photobiological production of hydrogen by marine green alga Platymonas subcordiformis. Biochem Eng J 19:69–73. Guo, L.J., Lu, Y.J., Zhang, X.M., Ji, C.M., Guan, Y., Pei, A.X. 2007. Hydrogen production by biomass gasification in supercritical water: a systematic experimental and analytical study. Catal Today 129:275–286. Hallenbeck, P.C., Benemann, J.R. 2002. Biological hydrogen production; fundamentals and limiting processes. Int J Hydrogen Energy 27:1185–1193. Han, S.-K., Shin, H.-S. 2004. Biohydrogen production by anaerobic fermentation of food waste. Int J Hydrogen Energy 29:569–577. Hao, X.H., Guo, L.J., Mao, X., Zhang, X.M., Chen, X.J. 2003. Hydrogen production from glucose used as a model compound of biomass gasified in supercritical water. Int J Hydrogen Energy 28:55–64. Hao, X.H., Guo, L.J., Zhang, X.M., Guan, Y. 2005. Hydrogen production from catalytic gasification of cellulose in supercritical water. Chem Eng J 110:57–65. Hawkes, F.R., Dinsdale, R.M., Hawkes, D.L., Huss, I. 2002. Sustainable fermentative hydrogen production: challenges for process optimization. Int J Hydrogen Energy 27:1339–1347. Howarth, D.C., Codd, G.A. 1985. The uptake and production of molecular hydrogen by unicellular cyanobacteria. J Gen Microbiol 131:1561–1569. Hussy, I., Hawkes, F.R., Dinsdale, R., Hawkes, D.L. 2005. Continuous fermentative hydrogen production from sucrose and sugarbeet. Int J Hydrogen Energy 30:471–483. Kamen, M.D., Gest, H. 1949. Evidence for a nitrogenase system in the photosynthetic bacterium Rhodospirillum rubum. Science 109:560. Klas, D. 2004. Biomass for renewable energy and fuels. Encyclopedia of energy. Elsevier, Oxford. Kruse, A., Meier, D., Rimbrecht, P., Schacht, M. 2000. Gasification of pyrocatechol in supercritical water in the presence of potassium hydroxide. Ind Eng Chem Res 39:4842–2848. Koskinen, P.E.P., Kaksonen, A.H., Puhakka, J.A. 2007. The relationship between instability of H2 production and compositions of bacterial communities within a dark fermentation fluidizedbed bioreactor. Biotechnol Bioeng 97:742–758.  Kotay, S.M., Das, D. 2008. Biohydrogen as a renewable energy resource: prospects and potentials. Int J Hydrogen Energy 33:258–263. Ledjeff-Hey, K., Kalk, T., Mahlendorf, F., Niemzig, O., Trautman, A., Roes, J. 2000. Portable PEFC generation with propane as fuel. J Power Sources 86:166–172. Levin, D.B., Pitt, L., Love, M. 2004. Biohydrogen production: prospects and limitations to practical application. Int J Hydrogen Energy 29:173–85. Li, S., Xu, S., Liu, S., Yang, C., Lu, Q. 2004. Fast pyrolysis of biomass in free-fall reactor for hydrogen-rich gas. Fuel Proc Technol 85:1201–1211. Lindblad, P., Chirstensson, K., Lindberg, P., Fedorov, A., Pinto, F., Tsygankov, A. 2002. Photoproduction of H2 by wildtype Anabaena PCC 7120 and a hydrogen uptake deficient mutant: from laboratory experiments to outdoor culture. Int J Hydrogen Energy 27:1271–1281. Lower, H.H. 1963. Chemistry of coal utilization, Suppl vol. Wiley, New York, pp. 740–815. Lu, Y., Guo, L., Zhang, X., Yan, Q. 2007. Thermodynamic modeling and analysis of biomass gasification for hydrogen production in supercritical water. Chem Eng J 131:233–244. Lu, Y.J., Jin, H., Guo, L.J., Zhang, X.M., Cao, C.Q., Guo, X. 2008. Hydrogen production by biomass gasification in supercritical water with a fluidized bed reactor. Int J Hydrogen Energy 33:6066–6075. Madamwar, D., Garg, N., Shah, V. 2000. Cyanobacterial hydrogen production. World J Microbiol Biotechnol 16:757–767. Maschio, G., Lucchesi, A., Stoppato, G. 1994. Production of syngas from biomass. Biores Technol 48:119–126.

218

6  Biohydrogen

Masukawa, H., Mochimaru, M., Sakurai, H. 2002. Hydrogenases and photobiological hydrogen production utilizing nitrogenase system in cyanobacteria. Int J Hydrogen Energy 27:1471– 1474. Melis, A., Happe, T. 2001. Hydrogen production. Green algae as a source of energy. Plant Physiol 127:740–48. Melis, A., Melnicki, M.R. 2006. Integrated biological hydrogen production. Int J Hydrogen Energy 31:1563–1573. Mertens, R., Liese, A. 2004. Biotechnological applications of hydrogenases. Curr Opin Biotechnol 15:343–348. Miao, X., Wu, Q. 2004. High yield bio-oil production from fast pyrolysis by metabolic controlling of Chlorella protothecoides. J Biotechnol 110:85–93. Midilli, A., Rzayev, P., Hayati, O., Teoman, A. 2000. Solar hydrogen production from hazelnut shells. Int J Hydrogen Energy 25:723–732. Milne, T.A., Elam, C.C., Evans, R.J. 2002. Hydrogen from biomass: state of the art and research challenges 1–82. National Renewable Energy Laboratory, Golden, CO. Minowa, T., Zhen, F., Ogi, T. 1997. Cellulose decomposition in hot-compressed water with alkali or nickel catalyst. J. Supercritical Fluids 13:253–259. Miura, Y. 1995. Hydrogen production by biophotolysis based on microalgal photosynthesis. Proc Biochem 30:1–7. Miura, Y., Akano, T., Fukatsu, K., Miyasaka, H., Mizoguchi, T., Yagi, K., Maeda, I., Ikuta, Y., Matsumoto, H. 1997. Stably sustained hydrogen production by biophotolysis in natural day/ night cycle. Energy Conver Manage 38:S533–S537. Miura, Y., Akano, T., Fukatsu, K., Miyasaka, H., Mizoguchi, T., Yagi, K., Maeda, I., Ikuta, Y., Matsumoto, H. 1995. Hydrogen production by photosynthetic microorganisms. Energy Convers Manage 36:903–906. Mohan, D., Pittman, C.U., Steele, P.H. 2006. Pyrolysis of wood/biomass for bio-oil: a critical review. Energy Fuels 20:848–889. Nandi, R., Sengupta, S. 1998. Microbial production of hydrogen: an overview. Critical Rev Microbiol 24:61–84. Nath, K., Das, D. 2003. Hydrogen from biomass. Current Sci 85:265–271. Nath, K., Das, D. 2004. Biohydrogen production as a potential energy resource: present state-ofart. J Sci Ind Res 63:729–738. Ormerod, J.G., Gest, H. 1962. IV. Hydrogen photosynthesis and alternative metabolic pathways in photosynthetic bacteria. Bacteriol Rev 26:51–66. Ormerod, J.G., Ormerod, K.S., Gest. H. 1961. Light-dependent utilization of organic compounds and photoproduction of molecular hydrogen by photosynthetic bacteria; relationships with nitrogen metabolism. Arch Biochem Biophys 94:449–463. Patil, K.Z. 1987. Hydrogen. Chem Age India 38:519–527. Paul, P.F.M., Wise, W.S. 1971. The principle of gas extraction. Mills and Boon, London. Prince, R.C., Kheshgi, H.S. 2005. The photobiological production of hydrogen: potential efficiency and effectiveness as a renewable fuel. Crit Rev Microbiol 31:19–31. Putun, A.E. 2002. Biomass to bio-oil via fast pyrolysis of cotton straw and stalk. Energy Sources 24:275–285. Rapagna, F.P.U. 1996. Hydrogen from biomass by steam gasification. Hydrogen Energy Progress XI, Proceedings of the 11th World Hydrogen Energy Conference, Stuttgart, Germany, 23–28 June 1996, 1:907–912. Rapagna, S., Foscolo, P.U. 1998. Catalytic gasification of biomass to produce hydrogen-rich gas. Int J Hydrogen Energy 23:551–557. Safrany, D.R. 1971. A potential large scale plasma process: synthesis of inexpensive hydrogen by using a thermonuclear device to vaporize waste organic materials. Chem Eng Progress Symp Ser 67:103–108. Salmenoja, K. 1993. Black-liquor gasification: theoretical and experimental studies. Biores Technol 46:167–171. Sasikala, K., Ramana, C.V., Rao, P.R., Kovacs, K.L. 1993. Anoxygenic phototrophic bacteria: physiology and advances in hydrogen technology. Adv Appl Microbio 38:211–295.

References 

219

Serebryakova, L.T., Sheremetieva, M., Tsygankov, A. 1998. FEMS Microbiology Lett 166:89. Shahbazov, Sh.J., Usupov, I. 1994. Non-trading sources of energy for hydrogen. Int J Hydrogen Energy 19:863–864. Stevens, D.J. 2001. Hot gas conditioning: Recent progress with larger-scale biomass gasification systems. National Renewable Energy Laboratory, NREL/SR-510-29952, Golden, CO. Sung, S. 2004. Biohydrogen production from renewable organic wastes. Final Technical Report. Iowa State University, Ames, IA. Susta, M.R., Luby, P., Mat, S.B. 2003. Biomass energy utilization and environment protection commercial reality and outlook, Power Gen Asia. http://www.powergeneration.siemens.com/ download/pool/industrialheatpower_02.pdf. Accessed 2009. Tran, D.Q., Charanjit, R. 1978. A kinetic model for pyrolysis of Douglas fir bark. Fuel 57:293– 298. Tsygankov, A.A., Kosourov, S.N., Tolstygina, I.V., Ghirardi, M.L., Seibert, M. 2006. Hydrogen production by sulfur-deprived Chlamydomonas reinhardtii under photoautrophic conditions. Int J Hydrogen Energy 31:1574–1585. Van Ginkel S., Sung, S., Lay, J.J. 2001. Biohydrogen production as a function of pH and substrate concentration. Environ Sci Technol 35:4726–4730. Van Ginkel, S.W., Logan, B. 2005. Increased biological hydrogen production with reduced organic loading. Water Res 39:3819–3826. Vayisoglu, E.S., Bartle, K.D., Erbatur, N.G., Frere, B., Snape, C.E., Erbatur, O. 1996. Chemical composition of SFE extracts obtained from coal and maceral concentrates. Fuel Process Technol 46:99–115. Vijayaraghavan, K., Soom, M.A.M. 2006. Trends in biohydrogen generation: a review. Environ Sci 3:255–271. Viswanathan, B. 2006. An introduction to energy sources. Indian Institute of Technology, Madras, India. Wagner, E.S., Froment, G.F. 1992. Steam reforming analyzed. Hydrocarbon Proc July:69–77. Walcher, G., Girges, S., Weingartner, S. 1996. Hydrogen Energy Progress XI, Proceedings of the 11th World Hydrogen Conference, 1996, Stuttgart. Wang, D., Czernik, S., Montane, D., Mann, M., Chornet, E. 1997. Biomass to hydrogen via fast pyrolysis and catalytic steam reforming of the pyrolysis oil or its fractions. Ind Eng Chem Res 36:1507–1518. Wang, D., Czernik, S., Chornet, E. 1998. Production of hydrogen from biomass by catalytic steam reforming of fast pyrolysis oils. Energy Fuels 12:19–24. Warnecke, R. 2000. Gasification of biomass: comparison of fixed bed and fluidized bed gasifier. Biomass Bioenergy 18:489–497. Watanabe, M., Iida, T., Inomata, H. 2006. Decomposition of a long chain saturated fatty acid with some additives in hot compressed water. Energy Convers Manage 47:3344–3350. Weissman, J.C., Benemann, J.R. 1977. Hydrogen production by nitrogen-starved cultures of Anabaena cylindrica. Appl Environ Microbiol 33:123. White, A.L., Melis, A. 2006. Biochemistry of hydrogen metabolism in Chlamydomonas reinhardtii wild type and a Rubisko-less mutant. Int J Hydrogen Energy 31:455–465. Yan, Q., Guo, L., Lu, Y. 2006. Thermodynamic analysis of hydrogen production from biomass gasification in supercritical water. Energy Convers Manage 47:1515–1528. Yanik, J., Ebale, S., Kruse, A., Saglam, M., Yuksel, M. 2007. Biomass gasification in supercritical water: Part 1. Effect of the nature of biomass. Fuel 86:2410–2415. Yogev, A., Kribus, A., Epstein, M., Kogan, A. 1998. Solar tower reflector systems: a new approach for high-temperature solar plants. Int J Hydrogen Energy 23:239–245.

Chapter 7

Fuel Cells

7.1 Introduction During the past decade, fuel cells have received an enormous amount of attention all over the world as novel electrical energy conversion systems. The higher efficiencies and lower emissions make the fuel cells a valuable contribution to the power generation facilities. As a clean energy source, hydrogen gas (H2) has potential if used in an electricity generating fuel cell (Caglar, 2003). H2 production by reforming of HC-based fuels in suitable fuel processors has become more and more important, in particular for both mobile and residential fuel cells applications (Specchia et al., 2005). The major factor that has influenced the development of fuel cells over the last few years is the worldwide concern of the environmental consequences of the use of fossil fuels in the production of electricity and for the propulsion of vehicles. Fuel cells seem to be the best solution for clean, efficient and non-hazardous energy. Fuel cells are electrochemical devices that convert the chemical energy of the fuels directly into electrical energy, and are considered to be the key technology for power generation in stationary, automotive, portable and even microscale systems. Among all kinds of fuel cells, direct methanol fuel cells have really exhibited the potential to replace current portable power sources and micropower sources in the market (Yao et al., 2006). A fuel cell produces electricity directly from the electrochemical reaction of hydrogen, from a hydrogen-containing fuel, and oxygen from the air. Hydrogen is industrially produced by steam reformation of naphtha oil, methane and methanol. High-purity hydrogen has been mainly used as a fuel for low-temperature fuel cells such as polymer or alkaline electrolyte fuel cells (Lin and Rei, 2000).

A. Demirbas, Biohydrogen, © Springer 2009

221

222

7  Fuel Cells

7.1.1 History of Fuel Cells In 1800, British scientists Sir William Nicholson (1753–1815) and Sir Anthony Carlisle (1768–1840) described the process of using electricity to decompose water into hydrogen and oxygen. Sir Humphrey Davy created in 1802 a simple fuel cell that allowed him to give himself a feeble electric shock. However, this result was not well-documented. The principle of the fuel cell was discovered by Christian Friedrich Schönbein (1799–1868) in 1838, who published his article about the hydrogen–oxygen fuel cell in the Philosophical Magazine in January 1839. Based on this work, the first fuel cell was demonstrated by Sir William Robert Grove in the February 1839 edition of the Philosophical Magazine and Journal of Science and later sketched, in 1842, in the same journal (Grove, 1839, 1842). Grove is known as the father of the fuel cell. At the London Institution, where he was professor of physics (1840–1847), he used his platinum–zinc batteries to produce electric light for one of his lectures (Chaurasia, 2000; Aravindhababu et al., 1999). Grove, however took this idea one step further or, more accurately, one step in reverse in 1839. He discovered that by arranging two platinum electrodes with one end of each immersed in a container of sulfuric acid and the other ends separately sealed in containers of oxygen and hydrogen, a constant current would flow between the electrodes. The sealed containers held water as well as the gases, and he noted that the water level rose in both tubes as the current flowed. By combining several sets of these electrodes in a series circuit, he created what he called a “gas battery”: the first fuel cell. Grove had speculated that the action in his gas battery occurred at the point of contact between electrode, gas, and electrolyte, but was at a loss to explain further. He also made fuel cells with ethylene and carbon monoxide. Friedrich Wilhelm Ostwald (1853–1932), a founder of the field of physical chemistry, provided much of the theoretical understanding of how fuel cells operate. In 1893, he experimentally determined the interconnected roles of the various components of the fuel cell: electrodes, electrolyte, oxidizing and reducing agents, anions, and cations. His exploration of the underlying chemistry of fuel cells laid the groundwork for later fuel cell researchers. In 1896, Antonio Henri Becquerel (1852–1908) made a new type of battery and used a carbon rod. Ludwig Mond and Carl Langer produced a gas-powered battery and called their system a fuel cell in 1889. In 1889, Ludwig Mond (1838–1909) and assistant Carl Langer described their experiments with a hydrogen-oxygen fuel cell that attained 6 A (ampere) per square foot at 0.73 V. Mond and Langer’s cell used electrodes of thin, perforated platinum. Dr. William W. Jacques further explored the carbon approach in 1896. His fuel cells had a carbon rod central anode in the electrolyte of molten potassium hydroxide. He made a fuel cell system of 100 cylindrical cells, which produced as much as 1500 W. Francis T. Bacon worked on fuel cells to produce alkaline systems that did not use noble metal catalysts in the 1930s. He developed and built a 6 kW alkaline hydrogen–oxygen system in 1959. In the same year, Dr. Harry Ihrig introduced

7.1  Introduction

223 Water out

Oxygen in

Hydrogen

−

+

Energy out

Fig. 7.1  Schematic of a hydrogen fuel cell

the first fuel cell tractor. Then a one-man submarine powered by a hydrazine and compressed oxygen fuel cell was produced. Currently, fuel cells are used to supply power and drinking water in space. The first stationary fuel cell power plant, PC-25, was developed by the International Fuel Cell Corporation (Ayhan, 2002). Francis T. Bacon (1904–1992) began researching alkali electrolyte fuel cells in the late 1930s. In 1939, he built a cell that used nickel gauze electrodes and operated under pressure as high as 3000 psi. During World War II, Bacon worked on developing a fuel cell that could be used in Royal Navy submarines, and in 1958 demonstrated an alkali cell using a stack of 10-in. diameter electrodes for Britain’s National Research Development Corporation. Though expensive, Bacon’s fuel cells proved reliable enough to attract the attention of the company Pratt & Whitney. The company licensed Bacon’s work for the Apollo spacecraft fuel cells. Beginning in the late 1950s and early 1960s, there was renewed interest in the fuel cell. NASA was looking for a way to power a series of upcoming manned space flights. Using batteries for power had already been ruled out due to weight considerations. Solar energy was too expensive at the time and nuclear power was determined to be too risky. In NASA’s search for an alternative, the fuel cell was thought to be a possible solution. NASA sponsored efforts to develop practical working fuel cells that could be used during these space flights. These efforts led to the development of the first proton exchange membrane fuel cell (PEMFC). In 1955, while NASA was conducting research, a scientist working at General Electric (GE) modified the original fuel cell design. In the early 1960s, aircraft engine manufacturer Pratt & Whitney licensed the Bacon patents for the alkaline fuel cell (AFC), and won a contract from NASA to supply these fuel cells to the Apollo spacecraft. Figure 7.1 shows a schematic of hydrogen fuel cell.

224

7  Fuel Cells

During the 1970s, fuel cell technology was developed for systems on Earth. The oil embargos of 1973 and 1979 helped to push along the research effort of the fuel cell as the US government was looking for a way to become less dependent on petroleum imports. A number of companies and government organizations began serious research into overcoming the obstacles to widespread commercialization of the fuel cell. Throughout the 1970s and 1980s, a large research effort was dedicated to developing the materials needed, identifying the optimum fuel source and drastically reducing the cost of this technology. During the 1980s, fuel cell technology began to be tested by utilities and automobile manufacturers. Technical breakthroughs during the decade included the development of the first marketable fuel cell-powered vehicle in 1993 by the Canadian company, Ballard.

7.2 Fundamentals of a Fuel Cell A fuel cell is a device in which the energy of a fuel is converted directly into electricity direct current (DC) by an electrochemical reaction without resorting to a burning process, rather than being converted to heat by a combustion reaction (Berger, 1968; Bockris and Srinivasan, 1969; McAuliffe, 1980; Kordesh, 1998; Larmine and Dicks, 1999; Chaurasia et al., 2003). The energy chemically stored in the fuels is converted into electric current by means of an electrochemical process in the fuel cell. More precisely, it is an electrochemical cell in which, at a uniform temperature, the free-energy change of a fuel/oxidizer reaction is converted directly and continuously to electric energy for as long as the reactants are supplied and the products are removed at an appropriate rate (Veziroglu, 1975). A fuel cell is an electrochemical conversion device. It produces electricity from fuel and an oxidant, which react in the presence of an electrolyte. The reactants flow into the cell, and the reaction products flow out of it, while the electrolyte remains within it. Fuel cells are different from electrochemical cell batteries in that they consume reactant, which must be replenished, whereas batteries store electrical energy chemically in a closed system. The chemical energy of the fuel is released in the form of an electrical energy instead of heat when the fuel is oxidized in an ideal electrochemical cell. Energy conversion by a fuel cell depends largely

FUEL (Chemical energy)

FUEL CELL

Energy conversion

Thermal energy

Mechanical energy

ELECTRICAL ENERGY

Fig. 7.2  Direct energy conversion with fuel cells compared to conventional indirect technologies

7.2  Fundamentals of a Fuel Cell

225

upon catalytic electrodes, which accomplish the electrochemical reaction to convert fuel into electric energy without involving the burning process. Efficiencies of fuel cells (40–85%) are considerably high when compared to heat engines. Catalysts are so expensive that electricity from most fuel cells costs about a thousand times more than the same amount derived from conventional sources. The need is to develop the catalysts from the different precursors to succeed in the necessary chemical reactions in an effective way (Demirbas, 2007a). Figure 7.2 shows the comparison of direct energy conversion with fuel cells to conventional indirect technologies. A fuel cell is an electrochemical energy conversion device similar to a battery, but differing from the latter in that it is designed for continuous replenishment of the reactants consumed, i.e., it produces electricity from an external supply of fuel and oxygen as opposed to the limited internal energy storage capacity of a battery. Additionally, the electrodes within a battery react and change as a battery is charged, or discharged, whereas a fuel cell’s electrodes are catalytic and relatively stable. Figure 7.3 shows the schematic of a fuel cell. Typical reactants used in a fuel cell are hydrogen on the anode side and oxygen on the cathode side (a hydrogen cell). Usually, reactants flow in and reaction products flow out. Virtually continuous long-term operation is feasible as long as these flows are maintained. The chemical energy of the fuel is released in the form of an electrical wave instead of heat when the fuel is oxidized in an ideal electrochemical cell. Many investigators believe that a stream of electrons produces the electricity current; however, it should not be forgotten that an electron always has a particle-wave character, which when transferring through an electrical conductor is a wave not a particle, i.e., an electron, during electrical current (Demirbas, 2002). Thus, energy conversion by a fuel cell depends largely upon catalytic electrodes, which accomplish the chemical reaction to convert fuel into electric energy without involving the burning process. The only basic difference between a fuel cell and an electrochemical cell is that, in a fuel cell, the combustible chemicals that generate the electrical current are stored separately and supplied to the electrodes on demand. In principle, therefore, a fuel cell can generate electricity by burning a fuel to electrical current. Like electrochemical cells, all fuel cells consist of a pair of electrodes, i.e., cathode and anode, and an electrolyte, plus an external circuit for electrical current and Air Oxygen

Electrolyte

Anode Fig. 7.3  Schematic of a fuel cell

Fuel

Cathode

Electrical current

226

7  Fuel Cells

Waste heat

Fuel

FUEL CELL

Electric energy

Oxidizer

Reaction products Fig. 7.4  A simplified fuel cell device

internal mechanism for allowing ion migration to complete the circuit. The output of electricity, which is always low-potential DC, is controlled by electrical potential or current regulators. In addition, they must have the associated hardware necessary for the controlled delivery of fuel and oxidizer to the electrodes, and each input and output is controlled in a suitable manner. A fuel cell can be simplified as in Fig. 7.4.

7.3 Different Types of Fuel Cells Various types of fuel cells have been developed to generate power according to the applications and load requirements (Chaurasia, 2000). There are several types of electrolyte, which plays a key role in the different types of fuel cells. It must permit only the appropriate ions to pass between the anode and cathode. The main electrolyte types are alkali, molten carbonate, phosphoric acid, proton exchange membrane (PEM), and solid oxide. The first three are liquid electrolytes, the last two are solids. There are several types of fuel cells with different characteristics and uses. Fuel cells are usually classified according to the electrolyte that is used. Table 7.1 shows some common fuel cell types and their uses.

7.3.1 Proton Exchange Membrane Fuel Cells (PEMFCs) Proton exchange membrane fuel cells (PEMFCs) work with a polymer electrolyte in the form of a thin, permeable sheet. The PEMFCs, otherwise known as polymer electrolyte fuel cells (PEFC), are of particular importance for the use in mobile and small/medium-sized stationary applications (Pehnt, 2001). The PEM fuel cells are considered to be the most promising fuel cell for power generation (Kazim, 2000).

7.3  Different Types of Fuel Cells

227

Table 7.1  Some common fuel cell types and their uses Type of fuel cell

Area of use

Electrolyte

Temperature (K)

Proton exchange membrane (PEM)

Transportation, space travel, small CHP, mobile equipment

Polymer

325−355

Alkaline (AFC)

Transportation, space travel

Alkaline

325−475

Direct methanol (DMFC)

Transport, mobile equipment

Polymer

355−475

Phosphoric acid (PAFC)

CHP, power plants

Phosphoric acid

465−485

Molten carbonate (MCFC)

CHP, power plants

Molten carbonate

875−925

Solid oxide (SOFC)

CHP, power plants

Solid oxide

875−1275

CHP: Combined heat and power

Electrical current

+

–

Oxygen

Hydrogen Porous conducting anode

Catalyst

Porous conducting cathode

Catalyst

Electrolyte membrane Fig. 7.5  Polymer electrolyte membrane fuel cell (PEMFC)

The advantages of PEMFCs over the other fuel cell systems are as follows (Chaurasia et al., 2003): 1. Quick-start capability 2. High power density 3. Relatively simple design 4. Light-weight fuel cell 5. Ability to adjust against variable power 6. Spontaneous off facility Figure 7.5 shows the polymer electrolyte membrane fuel cell (PEMFC). There are two porous metal plates connected in a circuit with a membrane between them. In

228

7  Fuel Cells

addition, the side of the metal plates facing the electrolyte membrane is coated with platinum as a catalyst. This catalyst is important in order for the fuel cell to work. The gases, H2 and O2, will pass through the porous plates and hit the catalyst. The efficiency of PEMFCs ranges from about 40 to 50%, and operating temperature is about 255 K. The PEMFCs and direct methanol fuel cells (DMFCs) are considered to be promising power sources, especially for transportation applications. The PEMFCs with potentially much higher efficiencies and almost zero emissions offer an attractive alternative to the internal combustion engines for automotive applications. This fuel cell has many important attributes such as high efficiency, clean, quiet, low-temperature operation, capable of quick start-up, no liquid electrolyte and simple cell design (Hu et al., 2004).

7.3.2 Direct Use of Methanol in Fuel Cells Methanol can be used blended with conventional fuels without engine modification or pure as a fuel. The direct methanol fuel cell (DMFC) is an extremely promising power source for portable applications due to its simple handling and processing of fuel. A DMFC converts chemical energy into electricity via oxidization of methanol. Research into the electrocatalysis of methanol has been stimulated by intense interest in advancing fuel cells (Gao et al., 2004). Main advantages of direct use of methanol in fuel cells are: (a) methanol is fed into fuel cell, (b) complicated catalytic reforming is not needed, and (c) the actual power densities of a DMFC are clearly lower than those of a conventional hydrogen-fed polymer electrolyte fuel cell. Methanol oxidation reaction at Pt and Pt alloy electrodes has attracted considerable attention during the last few decades in relation to direct methanol fuel cells (Seiler et al., 2004). Methanol can be used as one possible replacement for conventional motor fuels. The use of methanol as a motor fuel received attention during the oil crises of the 1970s due to its availability and low cost. Methanol is an attractive fuel: it is liquid at room temperature, it has limited toxicity, high energy density, and is an inexpensive energy source (Shukla et al., 1998). Methanol is a favored fuel as it has twice the energy density of liquid hydrogen and since it is a liquid at normal ambient temperatures and it can thus be stored and transported easily and inexpensively (Collins, 2001). Since methanol can be used as a blend with conventional fuels, without engine modification, or even pure as a fuel, it can also be used in traditional combustion engines and indirect methanol fuel cells. Methanol is also being viewed as an excellent base fuel for fuel cell vehicles. It can also be used as a base product for making biodiesel from vegetable oils (Demirbas, 2006). Methanol has been seen as a possible large-volume motor fuel substitute at various times during gasoline shortages. Methanol as a fuel can be used in two different ways: directly in the direct methanol fuel cell or indirectly in the indirect methanol fuel cell. The direct method liquid methanol is oxidized to carbon dioxide (CO2) without initial reforming. The indirect method transforms methanol into hydrogen via a reforming step while the direct way feeds methanol straight to the fuel cell.

7.3  Different Types of Fuel Cells

229

The direct methanol fuel cell (DMFC) is an extremely promising power source for portable applications due to its simple handling and processing of fuel. The direct use of methanol in fuel cells is considerably attractive from the point of view of simplicity of system design and hence cost (Shukla et  al., 2002). The performance of DMFCs has improved markedly in the past 5 years (He et al., 2004). The mutual effects of the oxygen reduction reaction and methanol oxidation reaction occurring simultaneously on a Pt/Vulcan fuel cell catalyst in O2-saturated 0.5  M H2SO4 solution containing 0.1 or 0.01 M methanol and the formation of a mixed potential were studied using differential electrochemical mass spectrometry (Jusys and Behm, 2004). A relatively new member of the fuel cell family, the DMFC is similar to the PEM cell in that it uses a polymer membrane as an electrolyte. The DMFC is a special form of low-temperature fuel cell. It can be operated at 355–475 K temperatures depending on the fuel feed and type of electrolyte used. In a DMFC, methanol is fed directly into the fuel cell without the intermediate step of reforming the alcohol into hydrogen (Collins, 2001). The DMFC, based on a polymer electrolyte fuel cell (PEFC), uses methanol directly for electric power generation and promises technical advantages for power trains. The fuel can be delivered to the fuel cell in a gaseous or liquid form. The actual power densities of a DMFC are clearly lower than those of a conventional hydrogen-fed polymer electrolyte fuel cell. In addition, methanol permeates through the electrolyte and oxidizes at the cathode. This results in a mixed potential at the cathode (Hohlein et al., 2000). Methanol is one of the few alcohols that can be fed directly into a fuel cell and can be converted electrochemically at the anode. The DMFC can be fed with a gaseous or liquid fuel feed. The liquid DMFC generally uses a diluted methanol in water mixture (typically 1–2 molar) and only a fraction of the methanol is used at the anode (Collins, 2001). The DMFC, like an ordinary battery, provides DC electricity according to the following half reactions. Methanol is oxidized to CO2 with half reaction at the anode: CH3OH + H2O → CO2 + 6H+ + 6e

(7.1)

and a cathode at which oxygen is reduced to water 1.5O2 + 6H+ + 6e → 3H2O

(7.2)

Accordingly, the overall cell reaction is: CH3OH + 1.5O2 → CO2 + 2H2O

(7.3)

The DMFC is similar to the PEMFC in that the electrolyte is a polymer and the charge carrier is the hydrogen ion (proton). However, the liquid methanol (CH3OH) is oxidized in the presence of water at the anode generating CO2, hydrogen ions and the hydrogen ions travel through the electrolyte and react with oxygen from the air. Because water is consumed at the anode in the oxidization half reaction, pure methanol cannot be used without provision of water via either passive transport such as back diffusion, or active transport such as pumping. Since the fuel cell operates isothermally, all the free energy associated with this reaction should in principle be

230

7  Fuel Cells Electrical current

–

+

H

+

Oxygen

Methanol Anode (Pt supported on C with polymer matrix)

Cathode (Pt supported on C with polymer matrix) CO2

H2O

Electrolyte membrane Fig. 7.6  Diagram of the operation of the DMFC membrane electrode assembly

converted to electrical energy. Figure 7.6 shows a schematic diagram of an operating DMFC system. In the direct methanol fuel cell, methanol is directly oxidized at the surface of the Pt/Ru (platinum/ruthenium) catalytic electrodes on the anode side to generate electricity without the need for any intermediate fuel processing and fuel reforming steps (Yao et al., 2006).

7.3.3 Characteristics of Main Types of Fuel Cells The characteristics of the main types of fuel cells are shown in Table 7.2. Alkali fuel cells (AFCs) operate on compressed hydrogen and oxygen. Alkaline electrolytes are generally less corrosive than acidic ones, and permit higher power output at ambient temperature and pressure. They are therefore preferred for fuel calls. The H2/O2 fuel cell operating with an alkaline electrolyte is the most highly developed and reliable of all fuel cells. High-purity hydrogen has been mainly used as a fuel for low-temperature fuel cells such as polymer or alkaline electrolyte fuel cells (Lin and Rei, 2000). They generally use an aqueous KOH solution as their electrolyte in AFCs. Efficiency of an AFC is about 70%, and operating temperature is about 470 K. Molten carbonate fuel cells (MCFCs) use high-temperature compounds of salt carbonates (such as Na2CO3, MgCO3) as the electrolyte. Efficiency of MCFCs ranges from 60 to 80%, and operating temperature is about 925 K. Phosphoric acid fuel cells (PAFCs) use phosphoric acid as the electrolyte. Efficiency of PAFCs ranges from 40 to 80%, and operating temperature is between 425 and 475 K. Solid oxide fuel cells (SOFCs) use a hard, ceramic compound of metal oxides (such as CaO, NiO, ZrO2, ZrO2(Y2O3), Ni–ZrO2(Y2O3), LaMnO3) as electrolyte. The SOFCs are an emerging technology including higher efficiencies and reduced emissions

7.4  Catalysts Used in Fuel Cells

231

Table 7.2  Characteristics of the main types of fuel cells Type of fuel cell

Operating temperature, K

Efficiency, %

Cell output, kW

Alkali

  425–2475

60–70

  0.3–5

Molten carbonate

  925

60–80

  0.1

Phosphoric acid

  425–475

40–80

50–200

Proton exchange membrane   255

40–50

50–200

Solid oxide

50–60

50–100

1275

(Karakoussis et al., 2001). Efficiency of a SOFC is about 60%, and operating temperatures are about 1275 K (Table 7.2). A fuel cell is not a heat engine, because is operates at a uniform temperature between ambient temperature (~293  K) to 1300  K. A heat engine is any device for transforming heat into mechanical work. The generation of electricity by burning fossil fuels using a boiler causes serious air pollution. All heat engines operate between two temperatures: the higher temperature T1 is that of the heat source, and the lower temperature T2 is that of the heat sink. According to the second law of thermodynamics the thermal efficiency (ηT) of a heat engine can be expressed as: T1 − T2 ηT =  (7.4) T1  where T1 and T2 are absolute temperatures. The theoretical efficiency of a Carnot engine is about 64%. The maximum ηT of most modern steam turbines is about 40%, but most other heat engines, such as internal combustion engines and reciprocating steam engines, are fortunate to achieve 30% efficiency. Clearly, the ηT of a heat engine can be 100% only if the temperature T2 is absolute zero, which is impossible. As a result, efficiencies of fuel cells are high compared to heat engines. The general advantages of fuel cells are:

1. Operates cleanly 2. Efficient (40–85%) 3. No moving parts 4. Reliable 5. Quiet start 6. Waste heat generated can be captured for other uses

7.4 Catalysts Used in Fuel Cells The fuel cell-powered cars will operate on conventional fuels. There has been much work reported in the literature by different researchers on the catalysts used in preparation of the catalytic electrodes of fuel cells (Ito et  al., 1991; Yamashita et  al.,

232

7  Fuel Cells

Table 7.3  Catalysts prepared from different precursors and used in present study of fuel cells Precursor

Catalyst

Composition

Loading ratio (wt.%)

H2PtCl6 . 6H2O

Pt

Single

5.0

RuCl3 . 3H2O + H2PtCl6 6H2O.

Ru

Composite

2.5

K2PtCl4

Pt

Single

5.0

RuCl3 . 3H2O + K2PtCl4

Ru

Composite

2.5

Pt

Pt

2.5

2.5

1991; Ning et al., 1999; Parker et al., 2004; Cao and Bergens, 2004; He et al., 2004; Seiler et al., 2004; Jusys and Behm, 2004). The new catalysts will be used in the onboard fuel reformer of an automotive fuel cell system to convert gasoline, or other hydrocarbon fuels, into hydrogen-rich gas. Carbon-supported platinum (Pt) and platinum–ruthenium (Pt–Ru) alloy are one of the most popular electrocatalysts in polymer electrolyte fuel cells (PEFCs). Pt supported on electrically conducting carbons, preferably carbon black, is being increasingly used as an electrocatalyst in fuel cell applications (Parker et al., 2004). Carbon-supported Pt could be prepared at loadings as high as 70 wt.% without a noticeable increase of particle size. Unsupported and carbon-supported nanoparticle Pt–Ruadatom (Pt–Ruad) catalysts prepared using the surface reductive deposition technique were evaluated as anode catalysts in liquid feed PEM-DMFCs. It was found that the surface composition of unsupported Pt–Ruad nanoparticles has a significant influence on their activities as anode catalysts in direct methanol fuel cells (Cao and Bergens, 2004). Carbon-supported Pt–Ruad catalysts display higher mass activities than unsupported Pt–Ruad. The electrochemical deposition of Pt–Ru nanoparticles on carbon nanotube electrodes and their electrocatalytic properties have been investigated by He et al. (2004). Table 7.3 shows the catalysts Ru and Pt, prepared from various precursors serving as electrolytic electrodes in the fuel cells (Chaurasia et al., 2003). Preferential oxidation of CO in a simulated reformed gas to CO2 by using selective CO oxidation catalysts was investigated. The effects of the preparation method, O2, water vapor, and CO2 concentration in the feed stream on the selective CO oxidation over Au/CeO2 catalysts were investigated in the temperature range of 323– 463  K (Luengnaruemitchai et  al., 2004). The activity of the Au catalyst depends very strongly upon the preparation method, with co-precipitation prepared Au/CeO2 catalysts exhibiting the highest activities. The process by which the hydrogen is burned in the presence of oxygen is: 2H2 + O2 → 2H2O + 494 kJ (heat)

(7.5)

The process for fuels cells is very similar, except that this time we get electricity instead of heat:

7.5  Use of Alternative Fuel in Fuel Cells

2H2 + O2 → 2H2O + 494 kJ (electricity)

233

(7.6)

The bond energy of the H–O bond is 460 kJ. The bond energy of H–H bonds is 431 kJ. The bond energy of the O=O bonds is 486 kJ. 4(H) + 2(O) → 2H2O + 1348 kJ

(7.7)

The formation of 2 mol of water from (H) and (O) atoms yields 1348 kJ. The decomposition of 2 molecules of water requires breaking 4 H–O bonds and thus the input of 1840 kJ. 4(H) + 2(O) → 4(H–O) + 1840 kJ

(7.8)

The formation of 4 H–O bonds from (H) and (O) atoms yields 1840  kJ. The maximum energy, 2 mol H2 and 1 mol O2, available from a PEMFC (with 50% efficiency) is 920 kJ.

7.5 Use of Alternative Fuel in Fuel Cells Alternative fuels can be used to power a fuel cell such as hydrogen, methane, natural gas, methanol, ethanol, liquefied petroleum gas and landfill gas, which can be produced from renewable energy sources such as biomass and wind. Fuel cells have several important benefits over conventional electrical energy generation from sources such as coal, as they are more efficient at converting fuel sources to end-use energy. The fuel cell vehicle will have no harmful emissions such as nitrogen oxide (NOx), sulfur oxide (SOx), or particulates. Fuel cells provide waste heat utilization in co-generation, units which serve to raise the overall energy efficiency (65–85%).

7.5.1 Biodiesel-Fueled Cells In the past decade, biodiesel has been gaining worldwide popularity as an alternative energy source because of its many benefits: this environment friendly fuel reduces tailpipe emissions, visible smoke and noxious odors (Ma and Hanna, 1999; Demirbas, 2003). Biodiesel is the only alternative fuel that produces basically no emissions during manufacture (Van Gerpen, 2005). Biofuels such as bioethanol, biomethanol, biohydrogen and biodiesel generally result in lower emissions than those of fossil-based engine fuels (Demirbas, 2007b). Many studies on the performances and emissions of compression ignition engines, fueled with pure biodiesel and blends with diesel oil, have been performed and are reported in the literature (Laforgia et al., 1994; Cardona et al., 1998). Biodiesel is being introduced to help reduce emissions from vehicles (Dicks et al., 2004). Figure 7.7 shows a schematic diagram of an operating gasoline, liquefied petroleum gas, methanol, ethanol and natural gas to electricity via fuel cell system.

234

7  Fuel Cells BIODIESEL METHANOL ETHANOL GLUCOSE GLYCEROL

AUTOTHERMAL REFORMER

Carbon monoxide

Water–gas shift reactor

Preferential oxidizer

BIOFUEL CELL

Fig. 7.7  Biodiesel, methanol, ethanol, glucose and glycerol to electricity via biofuel cell

The European Project BIOFEAT (Biodiesel Fuel Processor for a Fuel Cell Auxiliary Power Unit for a Vehicle) started in 2003. The overall aims of the use of biofuels were to reduce engine emissions and increase fuel economy (Specchia et al., 2005). An integrated auxiliary power unit (APU) based on a 10  kWe integrated biodiesel fuel processor has been designed and is being developed. Autothermal reforming (ATR) and thermal cracking (TC) were considered for converting the fuel into a hydrogen-rich gas suitable for PEM fuel cells (Sgroi et al., 2005). Specific programs were dedicated to modeling, project coordination and management. ATR and TC processes have been evaluated as part of the investigation into the primary fuel processor. The fuel processor also includes a gas clean up system that will reduce the carbon monoxide in the primary processor exit gas to below 10 ppm via a new heat-integrated CO clean-up unit, based on the assembly of catalytic heat exchange plates, so as to meet the operational requirements of a PEMFC stack (Sgroi et al., 2005). The following reactions take place in the ATR; a part of the feed is oxidized partially as follows (Specchia et al., 2005): 2C19H36O2

+ 17O2 → 38CO + 38H2

(7.9)

2H2

+ O2

→ 2H2O

(7.10)

2CO

+ O2

→ 2CO2

(7.11)

The remaining feed is catalytically reformed via the steam reforming and water– gas shift reactions: C19H36O2

+ 17H2O →  19CO + 35H2

(7.12)

CO

+ H2O

(7.13)

→  CO2 + H2

7.6  Hybrid Electric Vehicles and Supercapacitors

235

The main unit is the catalytic primary process reactor for H2 gross production, based on the ATR of biodiesel. After the primary step, secondary units for both the CO clean-up process and the simultaneous increase of the H2 concentration are employed: the H2 content from the reformated gas can be increased through the water–gas shift (WGS) reaction by converting the CO with steam to CO2 and H2. The high thermal shift (HTS) reactor is operating at 575–625 K followed by a low thermal shift (LTS) reactor operating at 475–535 K (Ruettinger et al., 2003). A preferential oxidation (PROX) step is required to completely remove the CO by oxidation to CO2 on a noble metal catalyst. The PROX reaction is assumed to take place in an isothermal bed reactor at 425 K after the last shift step (Rosso et al., 2004). The TC biodiesel fuel processor instead consists of a two-reactor system, in which one reactor, the cracker, is used for H2 production, while the other one is being regenerated by gasification of the deposited solid C with steam yielding H2, CO2, CO and CH4 (Ledjeff-Hey et al., 2000). The product gas streams of the TC and the gasification unit are combined, cooled down to the shift inlet temperature and then fed to the shift reactor and the CO-purification step. First, the cracking of biodiesel takes place for the production of H2: C19H36O2 → 17C + 2CO + 19H2

(7.14)

The regeneration process of the deposited C is then carried out in parallel, in a second reactor, via endothermic gasification: C + H2O → CO + H2

(7.15)

The cracking and gasification reactions are both carried out at an operating temperature of 1175 K.

7.6 Hybrid Electric Vehicles and Supercapacitors Plug-in hybrids are outfitted with a battery pack sufficient to power the vehicle for 35 miles or more on battery power alone. A plug-in hybrid electric vehicle (PHEV) is a hybrid vehicle with batteries that can be recharged by connecting a plug to an electric power source. It shares the characteristics of both conventional hybrid electric vehicles, having an electric motor and a backup internal combustion engine (ICE) for power, and of battery electric vehicles, also having a plug to connect to the electric grid. Most PHEVs on the road today are passenger cars, but there are also PHEV versions of commercial passenger vans, utility trucks, school buses, motorcycles, scooters, and military vehicles. Electric vehicles are clean, quiet, largely independent of imported petroleum, and can be powered using wind generation or another source of renewable electricity. Figure 7.8 shows the transportation fuels and petroleum-fueled, biorenewable-fueled, and renewable electricity-powered vehicles. Supercapacitors are electrical storage devices that can deliver a higher amount of energy in a short time. Hybrid electric and fuel cell-powered vehicles need such a surge of energy to start, more than can be provided by regular batteries. Superca-

236

7  Fuel Cells

Transportation fuels

Biorenewable fuels (ReFuels)

Bioethanol

Biohydrogen

Petroleum fuels

Biodiesel

Gasoline

Diesel fuel

Fuel cell Otto engine vehicle

Hybrid electric vehicle

Diesel engine vehicle

Renewable electricity (ReElectricity) Fig. 7.8  Transportation fuels and petroleum-fueled, biorenewable-fueled, and renewable electricity-powered vehicles

pacitors are also needed in a wide range of electronic and engineering applications, wherever a large, rapid pulse of energy is required. The most important difference between a supercapacitor and a battery is the principle of electrochemical energy storage. Electrochemical energy can be stored in two fundamentally different ways. Capacitors store the energy within the electrochemical double layer at the electrode/electrolyte interface (Viswanathan, 2006). Electrochemical capacitors have been studied for many years. The first patents date back to 1957, where a capacitor based on high surface area carbon was described by Becker. Later in 1969 first attempts to market such devices were undertaken by Standard Oil Company of Ohio (SOHIO). However, only in the 1990s did electrochemical capacitors become famous in the context of hybrid electric vehicles. The electrochemical capacitor (EC) was supposed to boost the battery or the fuel cell in the hybrid electric vehicle to provide the necessary power for acceleration, and additionally allow for recuperation of brake energy (Viswanathan, 2006). Stand-alone photovoltaic systems are designed to operate independently from the electric utility grid, and are generally designed and sized to supply certain DC and/or AC electrical loads. These types of systems may be powered by a photovoltaic array only, or may use wind, an engine-generator or utility power as an auxiliary power source in what is called a photovoltaic hybrid system. Figure 7.9 shows how a typical photovoltaic hybrid system might be configured (Viswanathan, 2006).

Summary 

237

PV array

Charge controller

DC load

Rectifier

Battery

Inverter

Engine-generator, wind turbine or grid backup

AC load

Fig. 7.9  Diagram of a photovoltaic hybrid system

Summary In recent years, fuel cells have received considerable research attention worldwide. Fuel cells are electrochemical devices that convert the chemical energy of the fuels directly into electrical energy, and are considered to be the key technology for power generation in stationary, automotive, portable and even microscale systems. A fuel cell produces electricity directly from the electrochemical reaction of hydrogen, from a hydrogen-containing fuel, and oxygen from the air. Hydrogen is industrially produced by steam reformation of naphtha oil, methane and methanol. Many investigators believe that a stream of electrons results in the electrical current, however, it should not be forgotten that an electron always has a particle-wave character and only a wave is transferred through an electrical conductor, i.e., an electron is not passed through the conductor, in an electrical current. The main electrolyte types are alkali, molten carbonate, phosphoric acid, proton exchange membrane (PEM), and solid oxide. Proton exchange membrane fuel cells (PEMFCs) work with a polymer electrolyte in the form of a thin, permeable sheet. The PEMFCs, otherwise known as polymer electrolyte fuel cells (PEFC), are of particular importance for the use in mobile and small/medium-sized stationary applications (Pehnt, 2001). The PEM type fuel cells are considered to be the most promising fuel cell for power generation. Methanol can be used in a blend with conventional fuels without engine modification or pure as a fuel. The direct methanol fuel cell (DMFC) is an extremely promising power source for portable applications due to its simple handling and processing of fuel. A DMFC converts chemical energy into electricity via oxidization of methanol. Research into the electro-catalysis of methanol has been stimulated by intense interest in advancing fuel cells. Main advantages of direct use of methanol in fuel cells are: (a) methanol is fed into a fuel cell; (b) complicated catalytic reforming is not needed; (c) the actual power densities of a DMFC are clearly lower than those of a conventional hydrogen-fed polymer electrolyte fuel cell. Fuel cells have several important benefits over conventional electrical energy generation from sources such as coal. They are more efficient at converting fuel sources to end-use energy. The fuel cell vehicle will have no harmful emissions

238

7  Fuel Cells

such as nitrogen oxide (NOx), sulfur oxide (SOx), or particulates. Fuel cells provide waste heat utilization in co-generation, units which serve to raise the overall energy efficiency (65–85%).

References Aravindhababu, P., Mohan, G., Sasikala, J. 1999. Emerging energy conversion techniques for next millennium, in Proceedings National Solar Energy Convention 1999, Indore, 20–22 Dec 1999. Pushpkunj, Indore. Ayhan, A.F. 2002. Design of a piezoelectrically actuated microvalve for flow control in fuel cells. M.S. Thesis, University of Pittsburgh, School of Engineering, Pittsburgh, PA. Berger, C. 1968. Handbook of fuel cell technology. Prentice-Hall, Englewood Cliffs, NJ. Bockris, O.M.J., Srinivasan, E. 1969. Fuel cells: their electrochemistry. McGraw-Hill, New York. Caglar, A. 2003. Gaseous products from solid wastes. Energy Edu Sci Technol 10:107–110. Cao, D., Bergens, S.H. 2004. Pt–Ruadatom nanoparticles as anode catalysts for direct methanol fuel cells. J Power Sources 134:170–180. Chaurasia, P.B.L. 2000. Solar energy utilization technology through chemical reactions: a report. Indian Council of Agricultural Research, New Delhi. Chaurasia, P.B.L., Ando, Y., Tanaka, T. 2003. Regenerative fuel cell with chemical reactions. Energy Convers Manage 44:611–628. Collins, J.A. 2001. Development of electrocatalyst materials for direct methanol fuel cells. Energy Marie Curie Fellowship Conference, Profactor GmbH, Steyr, Austria, 16–19 May 2001. Demirbas, A. 2002. Similarities and differences in electricity and light concepts: convenient dimensions theory. Energy Edu Sci Technol 9:69–74. Demirbas, A. 2003. Biodiesel fuels from vegetable oils via catalytic and non-catalytic supercritical alcohol transesterifications and other methods: a survey. Energy Convers Manage 44:2093– 109. Demirbas, A. 2007a. Fuel cells as clean energy converters. Energy Sources Part A 29:185–191. Demirbas, A. 2007b. Progress and recent trends in biofuels. Prog Energy Combus Sci 33:1–18. Dicks, A.L., Diniz da Costa, J.C., Simpson, A., McLellan, B. 2004. Fuel cells, hydrogen and energy supply in Australia. J Power Sources 131:1–12. Gao, L., Huang, H., Korzeniewski, C. 2004. The efficiency of methanol conversion to CO2 on thin films of Pt and PtRu fuel cell catalysts. Electrochim Acta 49:1281–1287. Grove, W.R. 1839. On voltaic series and the combination of gases by platinum. Phil Magazine J Sci XIV:127–130. Grove, W.R. 1842. On a gaseous voltaic battery. Philosophical Magazine J Sci XXI:417–420. He, Z., Chen, J., Liu, D., Zhou, H., Kuang, Y. 2004. Electrodeposition of Pt–Ru nanoparticles on carbon nanotubes and their electrocatalytic properties for methanol electrooxidation. Diamond Related Mater 13:1764–1770. Hohlein, B., von Andrian, S., Grube, Th., Menzer, R. 2000. Critical assessment of power trains with fuel-cell systems and different fuels. J Power Sources 86:243–249. Hu, G., Fan, J., Chen, S., Liu, Y., Cen, K. 2004. Three-dimensional numerical analysis of proton exchange membrane fuel cells (PEMFCs) with conventional and interdigitated flow fields. J Power Sources 136:1–9. Ito, E., Yamashita, M., Saito, Y. 1991. A composite Ru–Pt catalyst for 2-propanol dehydrogenation adaptable to the chemical heat pump system. Chem Soc Jpn Chem Lett 1:351–354. Jusys, Z., Behm, R.J. 2004. Simultaneous oxygen reduction and methanol oxidation on a carbonsupported Pt catalyst and mixed potential formation-revisited. Electrochimica Acta 49:3891– 3900. Karakoussis, V., Brandon, N.P., Leach, M., van der Vorst, R. 2001. The environmental impact of manufacturing planar and tubular solid oxide fuel cells. J. Power Sources 101:10–26.

References 

239

Kazim, M. 2000. Economical and environment assessments of proton exchange membrane fuel cell in public undertakings. Energy Convers Manage 42:763–72. Kordesh, K. 1998. Fuel cell and their applications. VCH, Weinheim. Laforgia, D., Ardito, V. 1994. Biodiesel fueled IDI engines: performances, emissions and heat release investigation. Biores Technol 51:53–59. Larmine, J., Dicks, A. 1999. Fuel cell system explained. Wiley, New York. Lin, Y.-M., Rei, M.-H. 2000. Process development for generating high purity hydrogen by using supported palladium membrane reactor as steam reformer. Int J Hydrogen Energy 25:211–219. Luengnaruemitchai, A., Osuwan, S., Gulari, E. 2004. Selective catalytic oxidation of CO in the presence of H2 over gold catalyst. Int J Hydrogen Energy 29:429–435. Ma, F., Hanna, M.A. 1999. Biodiesel production: a review. Biores Technol 70:1–15. McAuliffe, C.A. 1980. Hydrogen and energy. Macmillan, London, pp. 73–77. Ning, M., Ando, Y., Tanaka, T., Takashima, T. 1999. Study of photocatalytic 2-propanol dehydrogenation for solar thermal cell. American Institute of Aeronautics and Astronautics, AIAA2000-2863 (35th IECEC-2000; 7.24–7.28). Parker, S.F., Taylor, J.W., Albers, P., Lopez, M., Sextl, G., Lennon, D., McInroy, A.R., Sutherland, I.W. 2004. Inelastic neutron scattering studies of hydrogen on fuel cell catalysts. Vibration Spectrosc 35:179–182. Pehnt, M. 2001. Life-cycle assessment of fuel cell stacks. Int J Hydrogen Energy 26:91–101. Rosso, I., Galletti, C., Saracco, G., Garrone, E., Specchia, V. 2004. Development of A zeolitessupported noble-metal catalysts for CO preferential oxidation: H2 gas purification for fuel cell. Appl Catal B 48:195–203. Ruettinger, W., Ilinich, O., Farrauto, R.J. 2003. A new generation of water gas shift catalysts for fuel cell applications. J Power Sources 118:61–65. Seiler, T., Savinova, E.R., Friedrich, K.A., Stimming, U. 2004. Poisoning of PtRu/C catalysts in the anode of a direct methanol fuel cell: a DEMS study. Electrochimica Acta 49:3927–3936. Sgroi, M., Bollito, G., Saracco, G., Specchia, S. 2005. BIOFEAT: Biodiesel fuel processor for a vehicle fuel cell auxiliary power unit: Study of the feed system. J Power Sources 149:8–14. Shukla, A.K., Christensen, P.A., Dickinson, A.J., Hamnett, A. 1998. A liquid-feed solid polymer electrolyte direct methanol fuel cell operating at near-ambient conditions. J Power Sources 76:54–59. Shukla, A.K., Jackson, C.L., Scott, K., Murgia, G. 2002. A solid-polymer electrolyte direct methanol fuel cell with a mixed reactant and air anode. J Power Sources 111:43–51. Specchia, S., Tillemans, F.W.A., van den Oosterkamp, P.F., Saracco, G. 2005. BIOFEAT: Conceptual design and selection of a biodiesel fuel processor for a vehicle fuel cell auxiliary power unit. J Power Sources 145:683–690. Van Gerpen, J. 2005. Biodiesel processing and production. Fuel Process Technol 86:1097–1107. Veziroglu, T.N. 1975. Hydrogen energy: Part B. Plenum, New York. Viswanathan, B. 2006. An introduction to energy sources. Indian Institute of Technology, Madras, India. Yamashita, M., Kawamura, T., Suzuki, M., Saito, Y. 1991. Characteristics of suspended Ru/carbon catalyst for 2-propanol dehydrogenation applicable to chemical heat pump. Bull Chem Soc Jpn 64:272–278. Yao, S.C., Tang, X., Hsieh, C.C., Alyousef, Y., Vladimer, M., Fedder, G.K., Amon, C.H., 2006. Micro-electro-mechanical systems (MEMS)-based micro-scale direct methanol fuel cell development. Energy 31:636–649.

Chapter 8

The Hydrogen Economy

8.1 Introduction The hydrogen economy is a vision for a future in which hydrogen replaces fossil fuels. There are a variety of methods for generating, storing and delivering hydrogen since no single method has yet proven superior. Economically, the wasteful hydrogen process translates to electricity from hydrogen and fuel cells costing at least four times as much as electricity from the grid. In fact, electricity would be much more efficiently used if it were sent directly to the appliances instead. Low density and extremely low boiling point of hydrogen increases the energy cost of compression or liquefaction and the investment costs of storage. The low energy content of solar irradiation dictates that photosynthetic processes operate at high conversion efficiencies and places severe restrictions on photobioreactor economics (Hallenbeck and Benemann, 2002). Looking forward, towards the end of the century, solar-hydrogen type of fuels could be an option for a global energy economy. The hydrogen economy is a proposed method of deriving the energy needed for motive power (cars, boats, airplanes), buildings or portable electronics. Hydrogen production plays a very important role in the development of a hydrogen economy. One of the promising hydrogen production approaches is conversion from biomass, which is abundant, clean and renewable. Alternative thermochemical (pyrolysis and gasification) and biological (biophotolysis, water–gas shift reaction and fermentation) processes can be practically applied to produce hydrogen (Ni et al., 2006). The transition to a hydrogen economy will require a huge investment in new infrastructure to produce, store and deliver hydrogen to end-users. It will also require establishing hydrogen stationary systems, as well as developing and manufacturing fuel cells. In the long-term, a hydrogen-based economy will have an impact on all these sectors. The transition to the hydrogen-powered system could take several decades, because of the slow turnover of the existing stock of capital. The transition to hydrogen is likely to begin later in most developing economies than in the industrialized countries. The earlier industrialized countries/economies A. Demirbas, Biohydrogen, © Springer 2009

241

242

8  The Hydrogen Economy

begin the transition to hydrogen, the faster they can achieve their energy sustainability (UNEP, 2006). The local availability of biomass, solar and wind resources could provide the basis for the production of hydrogen in those countries where fossil fuel resources are scarce. Biomass, in particular, could be a low-cost option for some countries. Biomass, as a product of photosynthesis, is the most versatile non-petroleum renewable resource that can be utilized for sustainable production of hydrogen. Therefore, a cost-effective energy production process could be achieved in which agricultural wastes and various other biomasses are recycled to produce hydrogen economically (Nat and Das, 2003). Fortunately, hurdles in biomass gasification have been economic rather than technical. Until recently, biomass gasification has been employed to produce low-value products like electricity or heat, which rarely justify the capital and operating costs. But the increasing demand for hydrogen promises to make biomass gasification economically viable in the near future. A hydrogen economy would be based on two electrolytic processes both associated with heavy energy losses: electrolysis and fuel cells. Furthermore, between the conversion of electricity into hydrogen by electrolysis and the reconversion of hydrogen to electricity by fuel cells, the energy carrier gas has to be packaged by compression or liquefaction. It has to be distributed by road vehicles or pipelines, stored and transferred. Fuel cells convert fuel energy to electricity. They can contribute to a secure energy future only as long as they are used to generate electricity from original fossil source energy that otherwise would have been converted to electricity with conventional heat engines. Compared to thermal power plants, internal combustion engines and gas turbines fuel cells promise to be more efficient, cleaner, more convenient and less expensive. These arguments speak for fuel cells operated on natural gas, gasoline, diesel, methanol, ethanol, etc. (Bossel et al., 2003). The National Renewable Energy Laboratory (NREL), USA has explored the eco­nomic feasibility of producing hydrogen from biomass through various thermochemical routes. One study has been carried out to incorporate recent experimental advances in addition to plausible changes in direction from previous analysis performed by NREL. An assessment of hydrogen production technologies concludes that biomass gasification is the most economical process for renewable hydrogen production (McKinley et al., 1990), whereas other analyses have shown that biomass gasification/shift conversion is economically unfavorable compared to natural gas–steam reforming, except for very low-cost biomass and potential environmental incentives. Pyrolysis with a valuable co-product approach yields hydrogen in the price range of 6–8 US $/GJ, which is promising application in the near-term (Nath and Das, 2003). The pyrolysis-based technology, in particular, because of the co-products opportunity, has the most favorable economics. An added advantage of biomass as a renewable feedstock is that it is not intermittent, but can be used to produce hydrogen as and when required. With scientific and engineering advancements, biomass can be viewed as a key and economically viable component to a renewable-based hydrogen economy. Economic viability of different types of energy generation processes is summarized in Table 8.1 (Bockris, 1981; Tanisho, 1996; Benemann, 1997).

8.2  Cost of Hydrogen

243

Table 8.1  Unit cost of energy obtained by different processes Type of energy

Conversion efficiency (%)

Unit cost of energy of fuel (US $/MBTU)

Photobiological hydrogen

~ 10

~ 10

Fermentative hydrogen

~ 10

~ 40

Hydrogen from coal, biomass

    –

4

Hydrogen from advanced electrolysis

    –

10

Hydrogen from photochemical

    –

Fermentative ethanol

   15–30

21 ~ 31.5

8.2 Cost of Hydrogen Current research predicts that current oil and gas reserves will only last a few more decades. The twentieth century was the century of the petrochemical economy. However, the petroleum is a finite source for fuel that is rapidly becoming scarcer and more expensive. Biorefineries will not eliminate the need for petrochemicals in the twenty-first century, but they will play a key role in reducing our level of dependence on imported petroleum and making the twenty-first century one of an increasingly sustainable, domestic, and environmentally responsible biofuel economy (bioeconomy). Oil price increases have also increased the level of interest in bioenergy. Production of bioenergy, biofuel, and bioindustrial products derived from agriculture is accelerating rapidly. A strong bioeconomy may provide significant environmental benefits. Most of the biofuel production processes developed to date are immature and have never been implemented on an industrial scale. Projections of the amount of biofuel depend on the development of the bioeconomy and society. Biofuels are generally considered as offering many priorities, including sustainability, reduction of greenhouse gas emissions, regional development, social structure and agriculture, security of supply (Reijnders, 2006). There are several reasons for biofuels to be considered as relevant technologies by both developing and industrialized countries. These include energy security, environmental concerns, foreign exchange savings, and socioeconomic issues, mainly related to the rural sector. The estimation for the cost of biohydrogen is affected by a range of drivers that could change in direction and importance over time. These include: 1. Supply cost, market price and demand 2. Storage cost 3. Distribution cost 4. Production cost 5. Competing, non-energy markets for biomass 6. Access to market

244

8  The Hydrogen Economy

The calculation of biohydrogen prices should be designed to maintain in the future the equilibrium between demand and supply, taking into account the costs of planned investments. They should also take into account the rest of the economy and the environment. Two very important characteristics of energy prices are equity and affordability. Biohydrogen prices must reflect the cost, imposed by the specific consumer category on the economy. Since energy prices based on apparent long run marginal costs may not be sufficient to finance the development of the energy sector, the prices should be adjusted, so that the energy sector can be financed without subsidies to enhance its autonomy. In competitive markets this form of adjustment may not be possible. The marginal biohydrogen is the most expensive fuel that would be used where a target was met with the least cost. Fuels would be used in turn in order of price from lowest to highest. Our concern is with the most expensive fuel that would be used to meet the target, as that is the one that would be displaced by a lower-cost fuel. There are three cost factors that affect the biohydrogen costs: 1. Operating costs 2. Distribution and blending costs 3. Capital costs The operating costs are defined here as all costs that are not capital or feedstock costs. The literature contains a large variation in the estimation of operating costs. Where there is a range of costs reported in different sources, a mid-point has been used. The transition to a hydrogen-based energy economy, where the main chemical energy carrier is hydrogen and the main non-chemical energy form is electricity, is being made gradually, and is likely to continue to the middle or end of the twenty-first century (Midilli et al., 2005). Hydrogen opens access to a broad range of primary energy sources, including fossil fuels, nuclear energy and, increasingly, renewable energy sources (e.g., wind, solar, ocean, and biomass), as they become more widely available. Thus, the availability and price of hydrogen as a carrier should be more stable than any single energy source. Current world hydrogen production is approximately 50 million tons per year (45 billion kg per year), which represents 2% of world energy demand (Raman, 2003). However, current total annual worldwide hydrogen consumption is in the range of 400–500 billion Nm3. Of this quantity, approximately 97% is represented by captive or internal production and only about 3% is provided from merchant sources (MEDI, 2003). Hydrogen can be produced from a variety of domestic, renewable sources of energy. On-site hydrogen production can be done by steam gasification of natural gas (or, alternatively, of hydrogen carriers such as methanol or ammonia) or by electrolysis. Steam gasification is generally much cheaper than electrolysis at industrial scales because of the low price of natural gas compared to electricity. Today, virtually all hydrogen is produced by steam gasification (Berry et al., 1996; Kaarstad and Audus, 1997). Costs of liquid hydrogen from different methods com-

8.2  Cost of Hydrogen

245

Table 8.2  Costs and contents of thermochemical energies for selected energy carriers KWh/l Bio-liquid hydrogen

US $/l gasolineequivalent

2.64

0.123

1.00

10.00

0.050

0.45

Fossil-liquid hydrogen

2.64

0.073

0.58

Gasoline

9.10

0.060

0.55

0.015

0.14

Diesel oil

Heavy fuel oil Hydro-liquid hydrogen

11.70

a

2.64

0.136

1.18

10.20a

0.016

0.15

Wind-liquid hydrogen

2.64

0.268

2.36

Solarthermic-liquid hydrogen

2.64

0.359

3.16

Photovoltaic-liquid hydrogen

2.64

1.27

11.18

Natural gas

a

US $/kWh

Units in kWh/kg

pared to fossil fuels and fossil liquid hydrogen are listed in Table 8.2. Hydrogen can be produced using wind and solar electricity. The strategy is based on producing hydrogen from biomass pyrolysis using a co-product strategy to reduce the cost of hydrogen. It was concluded that only this strategy could compete with the cost of the commercial hydrocarbon-based technologies (Wang et al., 1998). This strategy will demonstrate how hydrogen and biofuel are economically feasible and can foster the development of rural areas when practiced on a larger scale. The process of biomass to activated carbon is an alternative route to hydrogen with a valuable co-product that is practiced commercially. Due in part to the advantages mentioned in Chap. 5, the production of hydrogen by SCWG from biomass provides for reducing the cost of production. Hydrogen is produced commercially in almost a dozen processes. Most of them involve the extraction of the “hydro” part from hydrocarbons. The most widely used, least costly process is “steam reforming,” in which natural gas is made to react with steam, releasing hydrogen (Hohhmann, 2002). While using steam to reform natural gas has proven the cheapest way to produce commercial hydrogen, natural gas is still a hydrocarbon and emits CO2 in the conversion process (Rifkin, 2002; Arni, 2004). Hydrogen is a synthetic energy carrier. The synthesis of hydrogen requires energy. Production, packaging, storage, transfer and delivery of the hydrogen gas, in essence all key components of an economy, are so energy-consuming that alternatives should be considered. The production technology would be site-specific and include steam reforming of methane and electrolysis in hydropower-rich countries.

246

8  The Hydrogen Economy Steam reforming Sulfur removal

Shift conversion

Steam Purge gas to reformer burners

PSA unit

Product hydrogen

Hydrocarbon feed Fig. 8.1  A schematic diagram of hydrogen from hydrocarbon feed by steam reforming

Hydrogen may be the only link between physical energy from renewable sources and chemical energy. It is also the ideal fuel for modern clean energy conversion devices like fuel cells or even hydrogen engines. Hydrogen for fleet vehicles would probably dominate in the transportation sector. To produce hydrogen via electrolysis and the transportation of liquefied hydrogen to rural areas with pipelines would be expensive. The cost of hydrogen distribution and refueling is very specific. However, there are some barriers to the development of a hydrogen economy. They are technological, economic, supply, storage, safety and policy barriers. Reducing these barriers is one of the driving factors in the government’s involvement in hydrogen and fuel cell research and development. Today the least expensive way of making hydrogen is through steam gasification of natural gas. Figure 8.1 shows a schematic diagram of hydrogen from hydrocarbon feed by steam reforming. Steam methane reforming (SMR), methanol reforming, and gasoline reforming are based on the same fundamental principles with modified operating conditions depending on the hydrogen-to-carbon ratio of the feedstock. Typically the feedstock is pre-treated to remove sulfur, a poison which deactivates nickel-reforming catalysts. The resulting cost of hydrogen is typically about 5–6 US $/GJ when made from natural gas at a price of 3 US $/GJ (Kaarstad and Audus, 1997). The conversion of natural gas to hydrogen almost doubles the price per unit of energy from 3 to 5–6 US $/GJ. The hydrogen has to show one or more substantial advantage over natural gas if it is to compete in the energy market. One such advantage would be the lack of CO2 and other greenhouse gas emissions if hydrogen is produced at enduse, and it can sometimes be that the technology for using hydrogen offers higher efficiency (i.e., fuel cells) or other favorable effects (e.g., low weight for space fuel application). At the present state of technologies for utilizing hydrogen it seems that the technology factor alone cannot justify the change to hydrogen as an energy carrier.

8.2  Cost of Hydrogen

247

Table 8.3  The economics of decarbonization conversion to hydrogen Production cost US $/GJ Today’s oil and natural gas price

3.0

Hydrogen from natural gas, CO2 to atmosphere

5.6

Hydrogen from natural gas with CO2 removed and stored underground

6.9

Hydrogen from coal with CO2 removed and stored underground

13.2

Hydrogen from water electrolysis based on an electricity price of 3.6 ¢/kWh

20.0

Conventionally produced hydrogen gas (with CO2 emitted to atmosphere) costs about twice that of natural gas or oil and about three times more than coal. At present only the space industry seems to be willing to pay the high cost of hydrogen energy (Demirbas and Caglar, 1998). The relative competitiveness of the various carbon-containing and non-carbon energy carriers are given in Table 8.3 (Surmen and Demirbas, 2005). It is obvious that hydrogen made from coal, oil, or natural gas will be more costly than these primary energy sources themselves. It is also obvious that catching and storing CO2 is more expensive than emitting the CO2 directly into the atmosphere. In general terms, it is expected that decarbonizing hydrogen made from natural gas or coal will increase the production cost by between 50 and 75%. Hydrogen gas that is produced conventionally (with CO2 emitted to atmosphere) costs about twice as much as natural gas or oil and about three times more than coal. Biomass residues are the cheapest feedstocks. Because of the low sulfur content of biomass, a sulfur removal system is not likely to be required. The current selling price of H2 in industry is generally between 5 US $/GJ and 14 US $/GJ, depending on the size of the production facility. This range is for hydrogen as produced by the plant: purified but not compressed or stored. For a conceptual process, the cost of hydrogen has been estimated to be 7.70 US $/GJ for the base case (production capacity: 35.5 tons of hydrogen per day) (Wang et al., 1997). The preliminary economic analysis of hydrogen from biomass by steam gasification indicates that the necessary selling price of hydrogen is well within current market values. The running cost of the generated hydrogen was carried out by processing 10 tons of the biomass. It was transported by truck for $ 16. The cost of 1 kg of purified hydrogen is only $ 0.68 (Rabah and Eldighidy, 1989). Hydrogen will play an important role in a future energy economy mainly as a storage and transportation medium for renewable energy sources. Renewable shares of 69% on the total energy demand will lead to hydrogen shares of 34% in 2050 (Rohland et al., 1992). The ability to store hydrogen more easily than electricity can help with load leveling and in balancing the intermittent nature of renewable energy sources. The share of individual primary energy sources in meeting final energy needs are given in Table 8.4 (Demirbas and Caglar, 1998). Hydrogen is also one of

248

8  The Hydrogen Economy

Table 8.4  Share of individual primary energy sources in meeting final energy needs (%) Source of energy

1998

2025

2050

Fossil fuels

88

62

29

Nuclear energy

10

 2

 2

Hydrogen from solar energy

 –

 7

31

Electricity from solar energy

 –

11

16

Heat from solar energy

 –

18

22

Energy from solar energy

 2

25

35

Hydrogen

 –

11

34

Table 8.5  Economics of decarbonization to electricity and hydrogen, US $/GJ Oil and natural gas price

 3

Electricity from coal with CO2 removed and stored underground

21.9

Electricity from natural gas with CO2 removed and stored underground

18.8

Coal-fired plant electricity price

12.5

Hydrogen from H2O electrolysis based on an electricity price: 3.6 ¢/kWh

20.0

Hydrogen from coal with CO2 removed and stored underground

13.2

Hydrogen from natural gas with CO2 removed and stored underground

  6.9

Hydrogen from natural gas, CO2 to atmosphere

  5.6

Table 8.6  The cost of hydrogen versus other fuels Fuel

Excluding efficiency differences

Including efficiency differences

Gasoline

0.21

0.21

Diesel fuel, No. 2

0.17

0.09

Electrolytic hydrogen

0.33–1.22

0.22–0.81

Electrolytic hydrogen (diesel operation)

0.33–2.22

0.18–0.67

Coal hydrogen (diesel operation)

0.24

0.13

Table 8.7  Better utilization of energy resources 1 ton coal converted to gasoline fuel-runs

  704 km

1 ton coal converted to electricity fuel-runs

  768 km

1 ton coal converted to methanol fuel-runs bus

  832 km

1 ton coal converted to hydrogen fuel-runs bus

1024 km

Summary 

249

the few energy carriers that enable renewable energy sources to be introduced into transport systems (Rohland et al., 1992). The economics of decarbonization to electricity and hydrogen is shown in Table 8.5 (Kaarstad and Audus, 1997). Table 8.6 shows what the cost of hydrogen versus other fuels is. Better utilization of energy resources are given in Table 8.7. Hydrogen can be transported by two systems: road delivery system (cryogenic liquid trucks, compressed tube trailers) and pipeline delivery system. Hydrogen pipeline costs could be reduced by placing the pipelines in sewers, securing utility status, or converting existing natural gas pipelines to carry a mixture of hydrogen/ natural gas (town gas). A hydrogen economy also involves hydrogen transport by trucks and ships. There are other options for hydrogen distribution, but road transport will always play a role, be it to serve remote locations or to provide back-up fuel to filling stations at times of peak demand. Hydrogen pipelines exist, but they are used to transport a chemical commodity from one production site to another. The energy required to move the gas is of secondary importance, because energy consumption is part of the production and energy expenditures are one part of the overall production cost. This is not so for hydrogen energy transport through pipelines. Normally, pumps are installed at regular intervals to keep the gas moving. These pumps are energized by energy taken from the delivery stream (UNEP, 2006). The infrastructure investment for fueling stations could reach 60% of the total capital costs. Delivery by cryogenic liquid hydrogen tankers is the most economical pathway for medium market penetration. They could transport relatively large amounts of hydrogen and reach markets located throughout large geographic areas. Tube trailers are better suited for relatively small market demand and the higher costs of delivery could compensate for losses due to liquid boil-off during storage. Pipelines are most effective for handling large flows. Operating costs for pipelines are relatively low. In the long run, when hydrogen is a very common energy carrier, distribution with pipeline is probably the preferred option. Hydrogen generated from rooftop solar electricity and stored at low pressure in stationary tanks may be a viable solution for private buildings. Compressed gas and liquid storage are the most commercially viable options today, but completely cost-effective storage systems have yet to be developed. The safety aspects with all storage options, particularly the novel hydride storage options, must not be underestimated (Schlapbach and Züttel, 2001).

Summary The hydrogen economy is a vision for a future in which hydrogen replaces fossil fuels. Economically, the wasteful hydrogen process translates to electricity from hydrogen and fuel cells costing at least four times as much as electricity from the grid. In fact, electricity would be much more efficiently used if it were sent directly to the appliances instead. The transition to a hydrogen economy would require a

250

8  The Hydrogen Economy

substantial investment in new infrastructure to produce, store and deliver hydrogen to end-users, establishing hydrogen stationary systems, as well as to develop and manufacture fuel cells. The transition to the hydrogen-powered system could take several decades, because of the slow turnover of the existing stock of capital. The transition to a hydrogen economy is likely to begin later in most developing economies than in the industrialized countries. A hydrogen economy would be based on two electrolytic processes both associated with heavy energy losses: electrolysis and fuel cells. Compared to thermal power plants, internal combustion engines and gas turbines fuel cells promise to be more efficient, cleaner, more convenient and less expensive. The calculation of biohydrogen prices should be designed to maintain in the future the equilibrium between supply and demand, taking into account the costs of planned investments. They should also take into account the rest of the economy and the environment. Two very important characteristics of energy prices are equity and affordability. Hydrogen is a synthetic energy carrier. The synthesis of hydrogen requires energy. Production, packaging, storage, transfer and delivery of the hydrogen gas, in essence all key component of an economy, are so energy-consuming that alternatives should be considered. The production technology would be site-specific and include steam reforming of methane and electrolysis in hydropower-rich countries. Conventionally produced hydrogen gas costs about twice that of natural gas or oil and about three times more than coal. At present only the space industry seems to be willing to pay the high cost of hydrogen energy. There are two hydrogen transport systems: road delivery system (cryogenic liquid trucks, compressed tube trailers) and pipeline delivery system. Hydrogen pipeline costs could be reduced by placing the pipelines in sewers, securing utility status, or converting existing natural gas pipelines to carry a mixture of hydrogen/ natural gas.

References Arni, S. 2004. Hydrogen-rich gas production from biomass via thermochemical pathways. Energy Edu Sci Technol 13:47–54. Benemann, J.R. 1997. Feasibility analysis of photobiological hydrogen production. Int J Hydrogen Energy 22:979–987. Berry, G.D., Pasternak, A.D., Rambach, G.D., Smith, J.R., Schock, R.N. 1996. Hydrogen as a future transportation fuel. Energy 21:289–303. Bockris, J.O’M. 1981. The economics of hydrogen as a fuel. Int J Hydrogen Energy 6:223–241. Bossel, U., Eliasson, B., Taylor, G. 2003. The future of the hydrogen economy: bright or bleak? Fuel Cell Seminar, 3–7 Nov 2003, Miami Beach, FL. Demirbas, A., Caglar, A. 1998. Catalytic reforming of biomass and heavy oil residues to hydrogen. Energy Edu Sci Technol 1:45–52. Hallenbeck, P.C., Benemann, J.R. 2002. Biological hydrogen production; fundamentals and limiting processes. Int J Hydrogen Energy 27:1185–1193. Hohhmann, P. 2002. Tomorrow’s energy: hydrogen, fuel cells, and the prospects for a cleaner planet. MIT Press, Cambridge, MA. Kaarstad, O., Audus, H. 1997. Hydrogen and electricity from decarbonised fossil fuels. Energy Convers Manage 38:S431–S436.

References 

251

McKinley, K.R., Browne, S.H., Neill, D.R., Seki, A., Takahashi, P.K. 1990. Hydrogen fuel from renewable resources. Energy Sources 12:105–110. Midilli, A., Ay, M., Dincer, I., Rosen, M.A. 2005. On hydrogen and hydrogen energy strategies I: current status and needs. Renew Sust Energy Rev 9:255–271. MEDI (Manitoba Energy Development Initiative). 2003. Department of Energy, Science and Technology. Preliminary hydrogen opportunities report. http://www.manitobaenergy.com. Accessed April 2003. Ni, M., Leung, D.Y.C., Leung, M.K.H., Sumalty, K. 2006. An overview of hydrogen production from biomass. Fuel Proc Technol 87:461–472. Rabah, M.A., Eldighidy, M.S. 1989. Low cost hydrogen production from waste. Int J Hydrogen Energy 14:221–227. Raman, V. 2003. Hydrogen infrastructure-market development. Air Products and Chemicals Inc., Allentown, PA. http://www.cleanair.org. Accessed 2009. Rifkin, J. 2002. The hydrogen economy. Jeremy P. Tarcher/Penguin, New York. Rohland, B., Nitsch, J., Wendt, H. 1992. Hydrogen and fuel cells: the clean energy system. J Power Sources 37:271–277. Schlapbach, L., Züttel, A. 2001. Hydrogen-storage materials for mobile applications. Nature 414:353–357. Surmen, Y., Demirbas, A. 2002. Thermochemical conversion of residual biomass to hydrogen for Turkey. Energy Sources 24:403–411. Tanisho, S. 1996. Feasibility study of biological hydrogen-production from sugar cane by fermentation. Hydrogen Energy Progress XI. Proceedings of 11th WHEC, Stuttgart, 3:2601–2606. UNEP (United Nations Environment Program). 2006. The hydrogen economy: a non-technical review. UNEP, Paris. Wang, D., Czernik, S., Chornet, E. 1998. Production of hydrogen from biomass by catalytic steam reforming of fast pyrolysis oils. Energy Fuels 12:19–24. Wang, D., Czernik, S., Montane, D., Mann, M., Chornet, E. 1997. Biomass to hydrogen via fast pyrolysis and catalytic steam reforming of the pyrolysis oil or its fractions. Ind Eng Chem 36:1507–1518.

Chapter 9

Hydrogen Policy

9.1 Introduction Current energy policies address environmental issues including environmentally friendly technologies to increase energy supplies and encourage cleaner, more efficient energy use, air pollution, greenhouse effect (mainly reducing carbon dioxide emissions), global warming and climate change (Demirbas, 2008). In general, an energy policy includes issues of energy production, distribution and consumption. It is also the manner in which a given entity has decided to address these issues. The attributes of energy policy may include international treaties, legislation on commercial energy activities (trading, transport, storage, etc.), incentives to investment, guidelines for energy production, conversion and use (efficiency and emission standards), taxation and other public policy techniques, energy-related research and development, energy economy, general international trade agreements and marketing, energy diversity, and risk factors contrary to possible energy crisis. There is considerable uncertainty in the economic analysis, associated with the costs of feedstocks and oil prices, and also because of the rapid development of the technologies. Any policy to support and encourage the supply of biofuel should provide incentives for both biodiesel and ethanol supplies. Policy options include incentive payments or tax breaks.Due to rising prices for fossil fuels (especially oil, but also natural gas and to a lesser extent coal) the competitiveness of biomass use has improved considerably over time. Biomass and bioenergy are now a key option in energy policies. Security of supply, an alternative for mineral oil and reduced carbon emissions are key reasons. Targets and expectations for bioenergy in many national policies are ambitious, reaching 20–30% of total energy demand in various countries. Similarly, long-term energy scenarios also contain challenging targets. Hydrogen could be a peaceful energy carrier for all countries. Hydrogen might be the next great fuel, as it is available worldwide and water is its only byproduct. Hydrogen has received increased attention as a renewable and environmentally friendly option to help meet today’s energy needs. A. Demirbas, Biohydrogen, © Springer 2009

253

254

9  Hydrogen Policy

Policy-makers will need to pay more attention to the implications for a transition to a hydrogen economy. The advantages of hydrogen praised by journalists (nontoxic, burns to water, abundance of hydrogen in the Universe, etc.) are misleading, because the production of hydrogen depends on the availability of energy and water, both of which are increasingly rare and may become political issues, as much as oil and natural gas are today. Due to some technological and economical consequences, practical uses of hydrogen energy do not have wide applications in the richest countries or in the poorest countries at present. For the developed countries, active involvement in hydrogen research and development, especially through collaborative international programs, could facilitate the introduction of new hydrogen technologies as they become competitive. A major dilemma now faced by the developing countries is how to invest in hydrogen research and development for the transition to hydrogen economy. Most developing countries will probably invest in hydrogen technology rather than be developers of cutting-edge technologies. Developing countries have at least as much to gain from a move towards the hydrogen economy as industrialized ones, since they generally suffer more from urban pollution and their economies tend to be more energy intensive. International organizations have an important role to play in assisting countries in creating a market-based policy relating to hydrogen and other clean energy systems (UNEP, 2006). International organizations should support the developing countries for the transition to a hydrogen economy as well as hydrogen production and distribution, to provide capital both national and foreign. Hydrogen’s share in the energy market is increasing with the implementation of fuel cell systems for sustainable energy supply. The concept of sustainable development embodies the idea of the interlinkage and the balance between economic, social and environmental concerns. Energy is an essential input for social development and economic growth. Globally, the demand for energy is increasing in consonance with socioeconomic development. Commercial energy consumption is increasing much faster in the developing countries. Energy use in developing countries has risen more than fourfold over the past three decades and is expected to continue increasing rapidly in the future. The increase in the services that energy provides is necessary for both economic and social development in the developing countries and to provide for increased human populations. Population growth is more rapid in developing countries. It is estimated to double by 2040, while the population of the industrial world will increase by only 15% over the same period.

9.2 Political, Environmental, and Economical Impacts of Hydrogen Energy is an essential input driving economic development. Therefore, in developed economies energy policies constitute an important component of overall regulatory frameworks shaping the improving overall competitiveness and market integration of the private business sector. Overall competitiveness includes liberalization of the

9.2  Political, Environmental, and Economical Impacts of Hydrogen

255

Table 9.1  Shares of alternative fuels in total automotive fuel consumption in the EU under the optimistic development scenario of the European Commission. Adapted from Demirbas (2008) Year

Biofuel

Natural gas

Hydrogen

Total

2010

6

 2

–

 8

2015

7

 5

2

14

2020

8

10

5

23

electricity and gas markets as well as by separation of energy production, transportation, and distribution activities. Current European Union (EU) policies on alternative motor fuels focus on the promotion of biofuels. The definition of the marginal producer depends on the policy stance on biofuels. Biofuel pricing policy should not be employed as an antiinflationary instrument. It should be applied in such a way, that it does not create cross subsidies between classes of consumers. In a proposed biofuels directive the introduction of a mandatory share scheme for biofuels, including as from 2009 minimum blending shares. Table 9.1 shows the shares of alternative fuels compared to the total automotive fuel consumption in the EU under the optimistic development scenario of the European Commission. The EU has set the goal of obtaining 5.75% of transportation fuel needs from biofuels by 2010 in all member states in February 2006. In the commission’s view mandating the use of biofuels will (a) improve energy supply security, (b) reduce greenhouse gas (GHG) emissions, and (c) boost rural incomes and employment (Jansen, 2003; Hansen et al., 2005). The European Union accounted for nearly 89% of all biodiesel production worldwide in 2005. By 2010, the United States is expected to become the world’s largest single biodiesel market, accounting for roughly 18% of world biodiesel consumption, followed by Germany. The general EU policy objectives considered most relevant to the design of energy policy are (Jansen, 2003): 1. Competitiveness of the EU economy 2. Security of energy supply 3. Environmental protection Producing and using biofuels for transportation offers alternatives to fossil fuels that can help provide solutions to many environmental problems. Using biofuels in motor vehicles helps reduce green house gas (GHG) emissions. Biodiesel and ethanol provide significant reductions in GHG emissions compared to gasoline and diesel fuel. Due to the low or zero content of pollutants such as sulfur in biofuels, the pollutant emission of biofuels is much lower than the emission of conventional fuels. Numerous low-emission scenarios have demonstrated that the Kyoto Protocol cannot be achieved without establishing a large role for biofuel in the global energy economy by 2050. Low-emission scenarios imply 50–70 EJ of biofuel raw material in 2050. Well-designed biofuel projects would have very significant sustainable

256

9  Hydrogen Policy

Table 9.2  Major benefits of biohydrogen Economic impacts

Sustainability and fuel diversity Increased number of rural manufacturing jobs Increased investments in plant and equipment International competitiveness Reducing the dependency on imported petroleum

Environmental impacts

Reducing of greenhouse gas emissions Reducing of air pollution Non-carbon fuel

Energy security

Peaceful and domestic targets Reducing use of fossil fuels Ready availability Domestic distribution Renewability

development benefits for rural areas, including creation of rural employment, rural electricity supply, soil conservation and environmental benefits (Demirbas, 2006). The main biofuel opportunities where suitable land is available are in developing countries. The issue of energy security has been accorded the top-most priority. Every effort needs to be made to enhance the indigenous content of energy in a time-bound and planned manner. The additional benefit of biofuel development is creation of new employment opportunities in manufacturing, construction, plant operation and servicing, and fuel supply. Rural jobs are created in fuel harvesting, transport and maintenance of processing areas (Demirbas, 2006). It is believed that in the future biomass can become an important sustainable source of hydrogen. The future prospects for hydrogen economy or economic hydrogen production are the basic point of many articles (Veziroglu, 1998; Goltsov and Veziroglu, 2002). At the end of the twenty-first century, the world will depend on the predominant use of carbon-free and carbon-neutral sources of energy, such as flow energy, solar energy, energy from modern biomass and safe nuclear energy (Quakernaat, 1995). Biomass has an advantage of having low environmental impact compared to that for fossil fuels. However, the price of hydrogen obtained by direct gasification of lignocellulosic biomass is about three times higher than that for hydrogen produced by steam reforming of natural gas (Spath et al., 2000). The strategy is based on producing hydrogen from biomass pyrolysis using a co-product strategy to reduce the cost of hydrogen and concluded that only this strategy could compete with the cost of the commercial hydrocarbon-based technologies (Wang et  al., 1998). This strategy will demonstrate how hydrogen and biofuel are economically feasible and can foster the development of rural areas when practiced on a larger scale. The process of biomass to activated carbon is an

9.3  Global Biofuel Projections

257

alternative route to hydrogen with a valuable co-product that is practiced commercially. Table 9.2 shows the major benefits of biohydrogen. During the first steps slow pyrolysis is used to maximize the yield of charcoal using densified biomass. The slow pyrolysis is used to maximize the yield of charcoal-producing organic vapors in 40% yield. The amount of hydrogen that can be produced from biomass is relatively low at 12–14%, which is based on the biomass weight. In the proposed second process, fast pyrolysis of biomass is used to generate bio-oil and catalytic steam reforming of the bio-oil to hydrogen and carbon dioxide.

9.3 Global Biofuel Projections Projections are important tools for long-term planning and policy settings. Renewable energy sources that use indigenous resources have the potential to provide energy services with zero or almost zero emissions of both air pollutants and greenhouse gases. Renewable energy is a promising alternative solution because it is clean and environmentally safe. Currently, renewable energy sources supply 14% of the total world energy demand. Approximately, half of the global energy supply from renewables in 2040. Photovoltaic (PV) systems and wind energy will be able to play an important role in the energy scenarios of the future. The most significant developments observed in renewable energy production have been with photovoltaics (from 0.2 to 784 Mtoe) and wind energy (from 4.7 to 688 Mtoe) between 2001 and 2040. Various scenarios have resulted in high estimates of biofuel in the future energy system. The availability of the resources is an important factor if high shares of biofuel penetrate the electricity, heat or liquid fuel market. The rationale is to facilitate the transition from the hydrocarbon economy to the carbohydrate economy by using biomass to produce bioethanol and biomethanol as replacements for traditional oil-based fuels and feedstocks. The biofuel scenario produced equivalent rates of growth in GDP and per capita affluence, reduced fossil energy intensities of GDP, reduced oil imports and gave an energy ratio. Each scenario has advantages whether it is rates of growth in GDP, reductions in carbon dioxide emissions, the energy ratio of the production process, the direct generation of jobs, or the area of plantation biomass required to make the production system feasible (Demirbas, 2006). Renewable resources are more evenly distributed than fossil and nuclear resources, and energy flows from renewable resources are more than three orders of magnitude higher than current global energy use. Today’s energy system is unsustainable because of equity issues as well as environmental, economic, and geopolitical concerns that have implications far into the future (UNDP, 2000). According to International Energy Agency (IEA), scenarios developed for the USA and the EU indicate that near-term targets of up to 6% displacement of petroleum fuels with biofuels appear feasible using conventional biofuels, given available cropland. A 5% displacement of gasoline in the EU requires about 5%

258

9  Hydrogen Policy

of available cropland to produce ethanol while in the USA 8% is required. A 5% displacement of diesel requires 13% of USA cropland, 15% in the EU. The recent commitment by the USA government to increase bio-energy threefold in 10 years has added impetus to the search for viable biofuels (IEA, 2006). The dwindling fossil fuel sources and the increasing dependency of the USA on imported crude oil have led to a major interest in expanding the use of bioenergy. The EU has also adopted a proposal for a directive on the promotion of the use of biofuels with measures ensuring that biofuels account for at least 2% of the market for gasoline and diesel sold as transport fuel by the end of 2005, increasing in stages to a minimum of 5.75% by the end of 2010 (Hansen et al., 2005). Figure 9.1 shows the shares of alternative fuels compared to the total automotive fuel consumption in the world as a futuristic view. Hydrogen is currently more expensive than conventional energy sources. There are different technologies presently being practiced to produce hydrogen economically from biomass. Biohydrogen technology will play a major role in the future because it can utilize the renewable sources of energy (Nath and Das, 2003). Biofuels are expected to reduce dependence on imported petroleum with associated political and economic vulnerability, reduce greenhouse gas emissions and other pollutants, and revitalize the economy by increasing demand and prices for agricultural products. Although most attention focuses on ethanol, interest in biodiesel is also increasing. Rapeseed is the primary oil used to make European biodiesel. Currently, biodiesel use is particularly strong in Germany. Biodiesel is primarily produced from soybeans in the US. The European Union has chosen biodiesel as its main renewable liquid fuel. Fuel use of ethanol in the European Union is much less important. Low European corn production and a high proportion of diesel engines compared to the United States make biodiesel a more attractive alternative in the European Union.

Biofuels

Natural gas

Hydrogen

20

Fig. 9.1  Shares of alternative fuels compared to the total automotive fuel consumption in the world. Adapted from Demirbas (2006)

Alternative fuel consumption, %

18 16 14 12 10 8 6 4 2 0 2000

2010

2020

2030 Year

2040

2050

9.3  Global Biofuel Projections

259

For fuels produced from biomass, various conversion routes are available that follow from the different types of biomass feedstocks. These routes include direct conversion processes such as extraction of vegetable oils followed by esterification (biodiesel), fermentation of sugar-rich crops (ethanol), pyrolysis of wood (pyrolysis oil derived diesel equivalent), and hydrothermal upgrading (HTU) of wet biomass (HTU oil derived diesel equivalent). Another possibility is to produce liquid biofuels (methanol, DME, Fischer–Tropsch liquids) from synthesis gas, which results from gasification of biomass. At present, the biofuel-producing countries in the European Union only have a small share in global production of biofuels, namely a little less than 6%. Most of the global biofuel production consists of ethanol. The main ethanol producers are the US and Brazil, whereas the share of Europe is rather small. However, Europe is the most important producer of biodiesel on the global market. Biomass is the most used renewable energy source now and in the future. The potential of sustainable large hydropower is quite limited to some regions in the world. The potential for small hydropower (< 10 MW) is still significant and will become more significant in the future. PV systems and wind energy are technologies with annual growth rates of more than 30% during the last years that will also become more significant in the future, as well as geothermal and solar thermal sources. PV will then be the largest renewable electricity source with a production of 25.1% of global power generation in 2040. The global and regional availability has been estimated for wind energy, solar energy especially photovoltaic (PV) cell, and biomass, together with a description of factors influencing this availability. In the long-term, countries with surplus biomass potential could develop into exporters of bioenergy. Renewable energy sources or renewables contributed 2% of the world’s energy consumption in 1998, including 7 exajoules (EJ) from modern biomass and 2 EJ for all other renewables (UNDP, 2000). The renewables are clean or inexhaustible and primary energy resources. Renewable technologies like water and wind power probably would not have provided the same fast increase in industrial productivity as fossil fuels (Edinger and Kaul, 2000). Biomass provides a number of local environmental gains. Energy forestry crops have a much greater diversity of wildlife and flora than the alternative land use, which is arable or pasture land. In industrialized countries, the main biomass processes utilized in the future are expected to be direct combustion of residues and wastes for electricity generation, bioethanol and biodiesel as liquid fuels and combined heat and power production from energy crops. The future of biomass electricity generation lies in biomass-integrated gasification/gas turbine technology, which offers high energy conversion efficiencies. Biomass will compete favorably with fossil mass for niches in the chemical feedstock industry. Biomass is a renewable, flexible and adaptable resource. Crops can be grown to satisfy changing end-use needs. In the future, biomass has the potential to provide a cost-effective and sustainable supply of energy, while at the same time aiding countries in meeting their greenhouse gas reduction targets. By the year 2050, it is estimated that 90% of the world population will live in developing countries.

260

9  Hydrogen Policy

Summary Current energy policies also address environmental issues including environmentally friendly technologies to increase energy supplies and encourage cleaner, more efficient energy use, air pollution, greenhouse effect, global warming and climate change. Any policy to support and encourage the supply of biofuel should provide incentives for both biodiesel and ethanol supplies. Policy options include incentive payments or tax breaks. Hydrogen could be a peaceful energy carrier for all countries. Hydrogen might be the next great fuel, as it is available worldwide and water is its only byproduct. Hydrogen has received increased attention as a renewable and environmentally friendly option to help meet today’s energy needs. Policy makers will need to pay more attention to the implications for the transition to a hydrogen economy. A major dilemma now faced by the developing countries is how to invest in hydrogen research and development for the transition to the hydrogen economy. Hydrogen’s share in the energy market is increasing with the implementation of fuel cell systems for sustainable energy supply. The concept of sustainable development embodies the idea of the interlinkage and the balance between economic, social and environmental concerns. The strategy is based on producing hydrogen from biomass pyrolysis using a co-product strategy to reduce the cost of hydrogen and concluded that only this strategy could compete with the cost of the commercial hydrocarbon-based technologies. Hydrogen is currently more expensive than conventional energy sources. There are different technologies presently being practiced to produce hydrogen economically from biomass. Biohydrogen technology will play a major role in the future because it can utilize the renewable sources of energy.

References Demirbas, A. 2006. Global biofuel strategies. Energy Edu Sci Technol 17:27–63. Demirbas A. 2008. Biodiesel: a realistic fuel alternative for diesel engines. Springer, London. Edinger, R., Kaul, S. 2000. Humankind’s detour toward sustainability: past, present, and future of renewable energies and electric power generation. Renew Sustain Energy Rev 4:295–313. Goltsov, V.A., Veziroglu, T.N. 2002. A step on the road to hydrogen civilization. Int J Hydrogen Energy 27:719–723. Hansen, A.C., Zhang, Q., Lyne, P.W.L. 2005. Ethanol-diesel fuel blends: a review. Biores Technol 96:277–285. IEA (International Energy Agency). 2006. Reference scenario projections. IEA, Paris. Jansen, J.C. 2003. Policy support for renewable energy in the European Union. Energy Research Centre the Netherlands. http://www.ecn.nl/docs/library/report/2003/C03113. Accessed 2009. Nath, K., Das, D. 2003. Hydrogen from biomass. Current Sci 85:265–271. Quakernaat, J. 1995. Hydrogen in a global long-term perspective. Int J Hydrogen Energy 20:485–492. Spath, P., Lane, J., Mann, M., Amos, W. 2000. Update of hydrogen from biomass: determination of the delivered cost of hydrogen. NREL Milestone Report.

References 

261

UNDP (United Nations Development Programme). 2000. World Energy Assessment. Energy and the challenge of sustainability. UNDP, New York. UNEP (United Nations Environment Program). 2006. The hydrogen economy: a non-technical review. Paris. Veziroglu, T.N. 1998. Dawn of the hydrogen age. Int J Hydrogen Energy 23:1077–1078. Wang, D., Czernik, S., Chornet, E. 1998. Production of hydrogen from biomass by catalytic steam reforming of fast pyrolysis oils. Energy Fuels 12:19–24.

Chapter 10

Environmental Impacts of Hydrogen

10.1 Introduction Today the world is facing three critical problems: (1) high fuel prices, (2) climatic changes, and (3) air pollution. Research suggests that current oil and gas reserves are sufficient for only a few more decades. It is well-known that transport is almost totally dependent on fossil fuels, particularly petroleum-based fuels such as gasoline, diesel fuel, liquefied petroleum gas, and compressed natural gas. Petroleumbased fuels are well-established products that have served industry and consumers for more than one hundred years. For the foreseeable future automotive fuels will still be largely based on liquid biorenewables and gaseous biohydrogen. However the time is running out and petroleum, once considered inexhaustible, is now being depleted at a rapid rate. As the amount of available petroleum decreases, the need increases for alternate technologies to produce liquid biorenewables and gaseous biohydrogen fuels that could potentially help prolong the liquid fuels culture and mitigate the forthcoming effects of the shortage of transportation fuels. Thermochemical conversion processes have met resistance from the environmental community and the public. An essential difference between direct combustion, pyrolysis, and gasification is that the latter two are intermediate processes for producing gaseous, liquid, and solid products that can be used in a wide variety of applications. Pyrolysis processes can be optimized for the production of biocrude oils. In the case of chemical and fuel production, the emissions from a direct process effluent can be avoided, although consideration must be given to emissions from the ultimate use of these products as they are used or combusted downstream. While exhaust gas cleanup of non-combustion thermochemical conversion processes may be easier than that associated with direct combustion, proper design of the process and emissions control systems is necessary to ensure that health and safety requirements are met. The output products of pyrolysis and gasification reactors can contain a variety of potential process and air pollutants that must be controlled prior to discharge into the ambient air. These include particulate matter A. Demirbas, Biohydrogen, © Springer 2009

263

264

10  Environmental Impacts of Hydrogen

(PM), aerosols or tars, oxides of nitrogen (NOx), oxides of sulfur (SOx), dioxins and furans, hydrocarbon (HC) gases, multiple metals, and carbon monoxide (CO). There are many strategies for controlling emissions from thermochemical conversion processes, and they are highly dependent on the process requirements of each individual facility. Subsidies and incentives are provided independently from the environmental impact that ethanol may have during its entire life cycle, therefore, supporting biofuel production in the US. In 2001, the European Commission launched a policy to promote the use of biofuels for transport in order to reduce greenhouse gas emissions and the environmental impact of transport, as well as to increase security of supply, technological innovation and agricultural diversification (UN, 2006). Environmental concerns have been raised in recent years dealing with greenhouse gases produced from the transportation industry. A contributing cause of these emissions is the combustion of fossil fuels such as diesel, gasoline and oil. A strong environmental initiative has pushed for the development of alternative fuels such as ethanol and biodiesel in pure and blended forms (Demirbas, 2008). Increasingly, engineering practitioners and managers need to know how to respond to challenges of integrating environmentally conscious technologies, techniques, strategies, and objectives into their daily work, and, thereby, find opportunities to lower costs and increase profits while managing to limit environmental impacts (Demirbas, 2008). The biofuels include bioethanol, biobutanol, fatty acid (m)ethylesters (biodiesel), vegetable oils, biomethanol, pyrolysis oils, fuels from Fischer–Tropsch synthesis, biogas, and biohydrogen. There are several reasons for biofuels to be considered as relevant technologies by both developing and industrialized countries. They include energy security reasons, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sector. Due to its environmental merits, the share of biofuel in the automotive fuel market will grow fast in the next decade (Kim and Dale, 2005; Demirbas and Balat, 2006). Advantages of biofuels are the following (Puppan, 2002): 1. Biofuels are easily available from common biomass sources 2. They represent a carbon dioxide cycle in combustion 3. Biofuels have a considerable environmentally friendly potential 4. There are many benefits to the environment, economy and consumers in using biofuels 5. They are biodegradable and contribute to sustainability There is a consensus amongst scientists that biofuels used in a sustainable manner result in no net increase in atmospheric carbon dioxide (CO2). Some would even go as far as to declare that sustainable use of biomass will result in a net decrease in atmospheric CO2 (Jefferson et al., 1991). This is based on the assumption that all the CO2 given off by the use of biomass fuels was recently taken in from the atmosphere by photosynthesis. Increased substitution of fossil fuels with biomassbased fuels would therefore help reduce the potential for global warming, caused by increased atmospheric concentrations of CO2.

10.2  Environmental Impacts of Hydrogen

265

10.2 Environmental Impacts of Hydrogen Hydrogen can be burned in such a way as to produce no harmful emissions. The fundamental attraction of hydrogen is its environmental advantages over fossil fuels. But hydrogen is only as clean as the technologies used to produce and use it. If hydrogen is produced without emitting any carbon dioxide or other climatedestabilizing greenhouse gases, it could form the basis of a truly sustainable energy system. Hydrogen can be produced from carbon-free or carbon-neutral energy sources or from fossil fuels with CO2 capture and storage (sequestration). Thus, the use of hydrogen could eventually eliminate greenhouse gas emissions from the energy sector. Vehicles and stationary power generation fueled by hydrogen are zero-emission devices at the point of use, with consequential local air quality benefits. Hydrogenpowered fuel cells could contribute to reducing or eliminating emissions of carbon dioxide and other greenhouse gases from road transportation vehicles. There is increasing interest in the role that hydrogen-based energy systems may play in the future, especially in the transport sector. They appear to be an attractive alternative to current fossil fuel-based energy systems in the future, since these have been proven to affect climate due to greenhouse gas emissions. Nevertheless, any future hydrogen-based economy would need to assess the possible global environmental impacts of such an alternative energy production. The scientists have estimated that the potential effects on climate from hydrogen-based energy systems would be much lower than those from fossil fuel-based energy systems. However, such impacts will depend on the rate of hydrogen leakage during its synthesis, storage and use. The researchers have calculated that a global hydrogen economy with a leakage rate of 1% of the produced hydrogen would produce a climate impact of 0.6% of the fossil fuel system it replaces. If the leakage rate was 10%, then the climate impact would be 6% of that of the fossil fuel system. A great attraction of hydrogen is pollution-free combustion while a host of undesirable compounds are emitted from gasoline and diesel fuel vehicles, or formed from their emissions. The main combustion product of hydrogen is water: H2 + O2 → 0.5H2O

(10.1)

The use of fossil fuels has a harmful impact on the environment. During the extraction, transportation, refinement, and storage of petroleum and petroleum products, spills and leakages occur, which causes water and air pollution. Most of the fossil fuel environmental impact occurs during the end-use combustion when tremendous amounts of various gases (CO2, CO, SOx, NOx, CH), soot and ash are produced and released into the atmosphere (Plass et al., 1990). Hydrogen vehicles would not produce, either directly or indirectly, significant amount of CO, HCs, particulates, SOx, sulfur-acid deposition, ozone and other oxidants, benzene and other carcinogenic aromatic compounds, formaldehyde and other aldehydes, lead and other toxic metals, smoke or CO2 and other greenhouse gases. The only pollut-

266

10  Environmental Impacts of Hydrogen

ant of concern would be NOx. If hydrogen is made from water using a clean power source, then hydrogen production and distribution will be pollution-free. The production of hydrogen electrolytically, using clean solar power or other forms of renewable energy is essentially pollution-free. The feedstock, water, is composed of hydrogen and oxygen. Hydrogen production or distribution would produce no CO2. Of the three fossil fuel feedstocks for hydrogen—oil, coal and natural gas—only coal will be available at relatively cheap prices over the next several decades. However, the use of coal to produce hydrogen would not be a desirable long-term option from an environmental standpoint (Demirbas and Caglar, 1998). An internal combustion engine fueled by hydrogen can be adjusted so that the emission of NOx is 200 times less than in present vehicles (Williamson and Edeskuty, 1986). Emissions of NOx increase with the temperature combustion temperature, the length of the high-temperature combustion period, and the availability of hydrogen, up to a point. There are several ways to control NOx in a hydrogen engine: run the engine very lean, which lowers the temperature, or very rich, which reduces the oxygen supplies, and decreases the burn time or lower the engine. The results of several hydrogen engine and vehicle emissions tests are shown in Table  10.1 (Deluchi, 1989).

Table 10.1  Emissions of hydrogen and same model gasoline vehicles Vehicle or engine

Fuel

Emissioncontrol

Emissions, g/km NOx

CO

CH

CO2

Reference

Dodge D-SO Pick-up

CH2

PCV

1.19

  0.44

0.26

8.66

CARB, 1986

Dodge D Pick-ups

Gasoline

CC, EGR

1.80

  2.73

0.28

3.70

EPA, 1987

Musashi-2

LH2

No CC

2.50

  0.18

0.05

–

Stewart, 1986

Ford 4-cl

Gasoline

No CC

1.42

21.9

1.41

–

Watson, 1984

BMW 745i, 6 cyl

LH2

No CC

0.35

  –

–

–

Strobl and Peschka, 1986

BMW 745i, 6 cyl

LH2

No CC

0.27

  –

–

–

Peschka, 1986

BMW 745i, 6 cyl

Gasoline

No CC

2.50

  –

–

–

Peschka, 1986

MB 280 TE Wagon

H2/Gasoline

No CC

0.52

  1.67

2.17

–

May, 1984

LH2: Liquid hydrogen PVC: Positive crankcase ventilation CC: Catalytic converter EGR: Exhaust gas re-circulation

10.2  Environmental Impacts of Hydrogen

267

Hydrogen offers the prospect of plentiful supplies of clean transportation energy. Analysis of hydrogen in efficient passenger vehicles was given a comprehensive review (Deluchi, 1989). That study addressed hydrogen production and distribution, on-board storage technology, re-fueling, vehicle performance and safety, the environmental impacts of hydrogen use, and life-cycle costs. The environmental impact analysis focuses on NO, emissions from vehicles, the environmental impacts of making hydrogen from coal, and the contribution to the greenhouse effect of CO2 emissions from the use of coal-based hydrogen. The life-cycle cost model compares hydrogen vehicles to similar baseline gasoline vehicles, and includes estimates of the total retail cost of liquid and gaseous hydrogen from coal and solar-powered electrolysis, the cost of fuel storage equipment, the cost of pollution control equipment, maintenance costs, other ownership and operating costs, and the external costs of hydrogen use. While there is considerable uncertainty about several important parameters, I conclude that under certain plausible (though not necessarily likely) conditions— low hydrogen fuel and vehicle costs, high non-market costs of gasoline use, and moderately strong efforts to avoid a greenhouse warming—hydrogen vehicles could be the socially preferred highway transportation option. Starch, cellulose or hemicellulose content of wastes, carbohydrate-rich food industry effluents or waste biological sludge can be further processed to convert the carbohydrates to organic acids and then to hydrogen gas by using proper bioprocessing technologies. Figure 10.1 shows schematic diagram for biohydrogen production from food industry wastewaters and agricultural wastes by two-stage, anaerobic dark and photofermentations (Karapinar Kapdan and Kargi, 2006). Hydrogen is one of the major trace gases in the lower atmosphere or troposphere. The mean global mixing ratio of hydrogen is currently about 510 ppb, 500 ppb in the northern hemisphere and 520 ppb in the southern hemisphere (Simmonds et al., 2000). Hydrogen is somewhat unusual among trace gases in that, although its life cycle has been heavily influenced by human activities, its mixing ratios in

Cellulose and starch containing wastes

Wastewater

Gringing

Dark fermentation

Pretreatment

Organic acids

Delignification

Photo-fermentation

Hydrolysis

Pretreatment

CO2, H2

CO2 H2 separation

CO2, H2

H2

Treated wastewater

Glucose syrup Fig. 10.1  A schematic diagram for biohydrogen production from cellulose/starch containing agricultural wastes and food industry wastewaters

268

10  Environmental Impacts of Hydrogen

the northern hemisphere are lower than those in the southern hemisphere. Because hydrogen reacts with tropospheric hydroxyl radicals, emissions of hydrogen to the atmosphere perturb the distributions of methane and ozone, the second and third most important greenhouse gases after carbon dioxide. Emissions of hydrogen can be compared to the six criteria pollutants (CO, SOx, NO2, PM, ozone, and lead) and GHGs from near and long-term methods of generating hydrogen for vehicles and stationary power systems, since it is important to evaluate effects of emissions on climate, human health, ecosystem and structures. The importance of hydrogen as a greenhouse gas was quantified (Derwent et al., 2001) using the global Lagrangian chemistry transport model STOCHEM. The model was started from an initial set of trace gas concentrations in October 1994, using analyzed wind fields to run the model through to 1 January 1995. At that point, two model experiments were initiated. The first model experiment continued on without change until 31 December 1998 and this formed the base case. In the second model experiment, the transient case, the hydrogen emission source strength was increased so that a pulse containing an additional 40 Tg of hydrogen was emitted into the model by 31 January 1995. At this point, the hydrogen emission was reset to the base case value and the model experiment was continued until 31 December 1998. The impacts of the additional hydrogen on the composition of the model troposphere were followed by taking differences between the base and transient cases. These differences in composition between the two experiments were termed “excess” concentrations. There was no particular significance to the size chosen for the emission pulse and it was given the same spatial distribution as that given to the man-made sources.

Summary Environmental concerns have been raised in recent years dealing with greenhouse gases produced from the transportation industry. The use of biohydrogen for transport in order to reduce greenhouse gas emissions and the environmental impact of transport, as well as to increase security of supply, technological innovation and agricultural diversification, has a strategic importance. Hydrogen can be burned in such a way as to produce no harmful emissions. The fundamental attraction of hydrogen is its environmental advantages over fossil fuels. But hydrogen is only as clean as the technologies used to produce and use it. If hydrogen is produced without emitting any carbon dioxide or other climate-destabilizing greenhouse gases, it could form the basis of a truly sustainable energy system. Vehicles and stationary power generation fueled by hydrogen are zero-emission devices at the point of use, with consequential local air quality benefits. Hydrogen-powered fuel cells could contribute to reducing or eliminating emissions of carbon dioxide and other greenhouse gases from road transportation vehicles. The production of hydrogen electrolytically, using clean solar power or other forms of renewable energy is essentially pollution-free. The feedstock, water, is composed of hydrogen and oxygen. Hydrogen production or distribution would produce no CO2. An internal combustion engine fueled by hydrogen can be adjusted so that the emis-

References 

269

sion of NOx is 200 times less than in present vehicles. Emissions of NOx increase with the temperature combustion temperature, the length of the high-temperature combustion period, and the availability of hydrogen, up to a point.

References CARB (Californian Air Resources Board). 1986. Mobile Source Division. Exhaust emission tests of a hydrogen fueled vehicle, MW-86-006, The Board El Monte, California, Protect 2F86EI. Deluchi, M.A. 1989. Hydrogen vehicles: an evaluation of fuel storage, performance, safety, environmental impacts, and cost. Int J Hydrogen Energy 14:81–130. Demirbas, A. 2008. Economic and environmental impacts of the liquid biofuels. Energy Edu Sci Technol 22:37–58. Demirbas, A., Caglar, A. 1998. Catalytic reforming of biomass and heavy oil residues to hydrogen. Energy Edu Sci Technol 1:45–52. Demirbas, M.F., Balat, M. 2006. Recent advances on the production and utilization trends of biofuels: a global perspective. Energy Convers Manage 47:2371–2381. Derwent, R.G., Collins, W.J., Johnson, C.E., Stevenson, D.S. 2001. Transient behavior of tropospheric ozone precursors in a global 3-D CTM and their indirect greenhouse effects. Climatic Change 49:463–487. EPA (Environmental Protection Agency). 1987. Test car list: passenger cars. EPA, Ann Arbor, MI. Jefferson, W.T, Wood, D.O., Ferrari, N.A. 1991. Energy and the Environment in the 21st century. MIT Press, Cambridge, MA. Karapinar Kapdan, I., Kargi. 2006. Biohydrogen production from waste materials. Enzyme Microbial Technol 38:569–582. Kim, S., Dale, B.E. 2005. Life cycle assessment of various cropping systems utilized for producing biofuels: bioethanol and biodiesel. Biomass Bioenergy 29:426–439. May, H. 1984. New results of engine driving tests of a 6-cylinder Otto-Engine in mixed hydrogen gasoline operation. 5th World Hydrogen Energy Conference, Toronto, Canada, 1984. Peschka, W. 1986. Liquid hydrogen fueled automotive vehicles in Germany-status and development. Int J Hydrogen Energy 11:721–728. Plass, H.J., Barbur, F., Miller, H.P., Veziroglu, T.N. 1990. Economics of hydrogen as a fuel for surface transportation. Int J Hydrogen Energy 15:663–668. Puppan, D. 2002. Environmental evaluation of biofuels. Periodica Polytechnica Ser Soc Man Sci 10:95–116. Simmonds, P.G., Derwent, R.G., O’Doherty, S., Ryall, D.B., Steele, L.P., Langenfelds, R.L., Salameh, P., Wang, H.J., Dimmer, C.H., Hudson, L.E. 2000. Continuous high-frequency observations of hydrogen at the Mace Head baseline atmospheric monitoring station over the 1994–1998 period. J Geophys Res 105:105–121. Stewart, W.F. 1986. Hydrogen as a vehicular fuel, in Recent developments in hydrogen technology, Vol. II, K.D. Williamson, F. Edeskuty (Eds.) CRC, Boca Raton, FL. Strobl, W., Peschka, W. 1986. Liquid hydrogen as a fuel of the future for individual transport, in T.N. Veziroglu, N. Getoff, P. Weinzier (Eds.), Hydrogen Energy Progress VI, Proceedings of 6th World Hydrogen Energy Conference, Vienna, Austria. Pergamon, New York. UN (United Nations). 2006. The emerging biofuels market: regulatory, trade and development implications. United Nations Conference on Trade and Development, New York and Geneva. Watson, H.C. 1984. An Australian hydrogen car, in T.N. Veziroglu, J.B. Taylor (Eds.), Hydrogen Energy Progress V, Proceedings of World Hydrogen Energy Conference, Toronto, Canada, Pergamon, New York. Williamson, K., Edeskuty, F. 1986. Recent developments in hydrogen technology, Vol. II, CRC, Boca Raton, FL.

Index

A acetic acid  13, 40, 46, 52, 69, 70, 96, 101–104, 171, 172, 175 acetone  40, 52, 69, 70, 77, 96, 101, 104 animal fats  53, 57, 62, 63, 71, 111 –– fish oil  71 –– grease  61, 99, 178 –– tallow (beef and sheep)  71 B bioalcohols  3, 63, 65 –– butanol  46, 65, 77, 94, 96, 98, 104, 264 –– ethanol  13, 21–23, 44, 49, 53–71, 77–98, 106, 164, 168, 176, 176, 204, 234, 253–260, 264 –– methanol  13, 14, 21, 23, 40, 52, 65–71, 82–106, 109, 123, 127, 129, 151–156, 181, 216–239, 242–248, 259 –– propanol  65, 94, 98, 104, 238, 239 biodiesel  22, 23, 40, 48, 52, 53, 57–74, 82–90, 97–104, 228–239, 253, 255, 258–260, 264, 269 –– advantages  72, 73 –– disadvantages  74 –– emissions  71–73 –– ethyl ester  86 –– higher heating value  101 –– methyl ester  71, 73, 86, 99, 101, 102 –– microemulsification  71 –– properties  71, 73 –– raw materials  71 –– algal oil  48 –– canola oil  22 –– cooking oil  57, 71 –– fish oil  71

–– grease (brown and yellow)  61, 99 –– palm oil  71, –– soybean oil  22, 71, 99–104 –– tallow  71 –– transesterification  53, 57, 71, 83, 86, 99, 238 –– non-catalytic supercritical methanol  238 –– viscosity  71–74, 86, 87, 101, 102 biofuels  19, 23, 48, 53–58, 61–85, 233, 234, 243, 255–259, 264, 269 –– bioethanol  22, 23, 52–65, 82–85, 95, 233, 236, 257, 259, 264, 269 –– history  64 –– biofuel economy  243 –– biogas  19, 23, 33–35, 52–57, 61–66, 74–78, 82–84, 164, 264 –– anaerobic digestion  23, 34, 55, 59, 74–78, 83, 84, 111, 164, 178 –– biogasoline  63 –– biohydrogen  1, 23, 24, 40–43, 61, 78, 82–85, 163–219, 233, 236, 243, 244, 250, 253–269 –– biomethanol  52, 61, 65, 67, 82, 233, 257, 264 –– bio-oil  52, 56, 59, 61, 63, 68, 69, 82, 84, 100–104, 176–178, 181, 209–213, 218, 257 –– biosyngas  61, 63, 66, 68, 69, 81, 82, 99, 187 –– carbon dioxide  167, 186 –– carbon monoxide  186, 187 –– ethane  81 –– hydrogen  186, 187 –– economic impact  62 271

272 –– feedstocks  257 –– algae  63, 210 –– cellulose  35, 64, 65, 76, 79, 82, 267 –– corn (maize)  53, 54, 58, 61–65, 81–83, 107, 202, 258 –– cereal crops  53 –– glucose  49, 53, 54, 65, 76, 169, 175, 202, 205, 215, 217, 234, 267 –– grass  45, 48, 57, 64, 179 –– non-cereal crops  54 –– starch  45, 49–54, 57,58, 62–64, 174, 175 –– sucrose  41, 53, 65, 189, 217 –– sugar beet  45, 53, 64, 65, 95 –– sugar cane  45, 53, 58, 64, 65, 82, 95, 189, 251 –– sugar crops  45, 57 –– switchgrass  45, 57, 64, 82 –– global biofuel projections  257–259 –– production by fermentation  169 –– carbohydrates  170 –– sugars  53, 69 biohydrogen  1, 23, 24, 61, 63, 78, 82, 83, 85, 163 –– biological production processes  166–175 –– anaerobic  170, 175 –– anaerobic bacteria  24, 166, 169, 170–175 –– cyanobacteria  24, 166 –– fermentative bacteria  24, 166, 175 –– microbial fermentation  170 –– biophotolytic  172 –– dark fermentation  174 –– photobiologically  1, 128, 163 –– photocatalytic  119–239 –– photoelectrochemical  1, 111, 115, 118, 119, 125, 128, 152 –– photofermentation  24 –– photosynthetic bacteria  24, 170 –– definition  164 –– history  164, 222 –– production  166, 168, 170, 174–214, 233, 236, 243, 244, 250, 256–260, 263, 264, 267, 268 –– thermochemical production processes  176–197 –– pyrolysis  179 –– gasification  186 –– non-conventional  195 –– steam reforming  197 –– supercritical water gasification  176, 177, 202–205, 214

Index biomass  1–4, 18–28, 43–88, 95–111, 115, 128, 129, 164, 165, 178–205, 233–236, 243–260, 264–269 –– adhesives from  23, 179 –– bio-oil  52–56, 61, 63, 68, 69, 82, 100–104, 176–178, 181, 209–214, 257 –– cellulose  21, 35, 49, 50, 57, 64–67, 79, 103, 168,169, 180,182, 201–208, 267 –– char (biochar, charcoal)  46, 52, 56, 61, 82, 100, 177–183, 187–196, 200, 202, 205, 210, 213, 257 –– chemicals from  67, 68 –– acetic acid  46, 52, 69, 70, 102, 103 –– acetone  52, 69, 70, 101 –– dimethoxyphenol  69, 70, 102 –– cyclopentanone  52 –– formic acid  52, 70 –– furfural  52, 69, 70 –– levoglucosan  52, 70 –– methanol  21, 23, 52, 65–71, 82 –– methoxyphenol  52 –– phenol  52, 69, 70 –– chemistry  49 –– definition  43 –– extractives  48, 58, 182 –– feedstocks  45–48, 53, 187, 188, 259 –– algae  2, 21, 24, 43, 45, 48, 49, 63, 166–172, 208–213 –– aquatic plants  21, 43, 45 –– crop grain  24 –– energy crops  23, 45, 52, 54, 57, 165, 178, 180, 259 –– food crops  45 –– grasses  45, 48, 51, 54, 57 –– kelps  45, 48 –– landfill  4, 21, 33–36, 45, 74, 75, 78, 83, 233 –– lichens  45, 48 –– manure slurry  24, 56 –– mosses  45, 48, 208–213 –– municipal solid waste  19, 21, 24, 33–35, 43–46, 64, 78, 82, 170, 179, 189 –– non-food crops  63 –– olive husk  24, 47, 180, 182, 184 –– pulp and paper waste  24 –– sugar beet  45, 53, 64, 65, 95 –– sugar cane  45, 53, 58, 64, 65, 82, 95, 189 –– sugar crops  45, 57 –– tea waste  24, 47, 56, 57, 181–185, 200, 201 –– wheat straw  47, 55, 56, 63, 177

Index –– analysis  46, 47 –– ash content  51, 193 –– higher heating value  46, 47 –– moisture content  202 –– furfural  52, 69, 70 –– glucose  49–54, 65, 67, 167–170 –– hemicelluloses  21, 49, 50, 58, 67, 68, 103, 182, 201 –– holocellulose  49, 58 –– hydrolysis (saccharification)  49, 52–54, 58, 65–68, 77, 102 –– landfill gas  21, 34, 35, 74, 75, 78, 83, 233 –– lignin  21, 49–51, 58, 67, 68, 103, 179, 182, 201, 207 –– content  201 –– modern biomass  4, 19, 22, 23, 194, 195, 256, 259 –– photosynthesis  43–45 biomass thermochemical conversion processes  21, 23, 39, 176, 214 –– biochemical conversion  44, 57, 164, 168 –– combustion  21–23, 44, 46, 50–52, 72, 73, 192 –– direct  21–24, 34, 43, 194, 259, 263 –– indirect  43 –– efficiency  62, 72 –– Fischer–Tropsch synthesis (FTS)  22, 79–83, 264 –– gasification  19–24, 39, 186 –– steam gasification  23, 24, 39, 114, 176–180, 197–218, 244–247 –– hydrothermal upgrading  68, 259 –– supercritical water gasification  176, 177, 202–205, 215 –– liquefaction  21 –– direct  21 –– pyrolysis  19–23, 39 –– hydropyrolysis  181 –– mechanisms  180 –– methanopyrolysis  181 –– ultrapyrolysis  181 biorefinery  67–69, 83 biorenewables  100, 163, 166–203, 263 biorenewable gaseous fuels  78, 83 –– biogas  19, 23, 33–35, 52–57, 62–66, 74–78 C coal  2–7, 10–17, 45, 66, 67, 80, 85, 88, 99, 105, 106, 110–115, 163, 1898, 191, 202, 233, 237, 243, 247–253, 257 –– benzene  13

273 –– –– –– –– –– –– –– –– –– ––

bituminous coal  10–12, 189 brown coal  10, 14 cresol  13 formaldehyde  13 lignite  5, 10–12, 39, 189 pyrolysis  67 reserves  11, 12 synthesis gas  13 toluene  13 xylene  13

D diesel (fuel)  9, 10, 22, 61, 71–74, 79–89, 97–99, 103, 248, 255, 263, 265 dimethyl ether (DME)  52, 85–88, 98, 103, 106 E energy sources  1–5, 39 –– fissile  2, 36 –– thorium  2, 36 –– uranium  2, 36 –– fossil  2–26 –– conventional  5 –– unconventional  14 –– global energy sources  4 –– nuclear  2, 36 –– renewable  1–5, 18–39 –– biomass  21 –– hydropower  25 –– geothermal  27 –– wind  28 –– solar  30 –– others  33 ethanol (ethyl alcohol)  13, 21–23, 44, 49, 54, 57, 63–68, 77, 79, 82–87, 94–98, 104, 106, 164, 168, 175, 176, 258 –– production  63–65 –– from biomass  61 ethene  66 F Fischer–Tropsch synthesis (FTS)  13, 22, 78–82, 264 –– diesel  32 Fischer–Tropsch (FT) liquid products  13 fuel cell  15, 24, 52, 75, 82, 86, 93, 94, 103–107, 115, 145, 151, 187, 198, 221–238, 241, 242, 246, 250, 254, 268 –– characteristics  230, 231 –– catalysts used in  231, 232 –– device  223, 226–227, 230

274 –– alternative fuel used in  233 –– biodiesel-fuelled  233–235 –– biorenewable-fuelled  236 –– petroleum-fuelled  236 –– history  222–224 –– types  226 –– proton exchange membrane  226, 227 –– direct methanol  228 G gas hydrates  16, 17 –– clathrates  16 –– methane  16 –– gas hydrates  16 –– natural gas  16 gasoline  9, 10, 14–18, 22–24, 61–66, 72, 79–103, 106–109, 134, 135, 145–148, 228–233, 236, 242–258, 263–269 –– gasohol  65 –– octane number  91, 94, 97, 98 –– Otto engine  66, 87, 95, 97, 146, 236, 269 gasoline-alcohol mixtures  97, 98 glycerol  35, 79, 234 H hybrid electric vehicles  235, 236 hydrogen  1–25, 34, 35, 39, 44, 49, 51, 58, 61, 63, 66–69, 74–86, 93, 94, 97, 103–214, 222–237, 241–250, 253–269 –– advantages of hydrogen as engine fuel  146 –– disadvantages of hydrogen as engine fuel  147 –– economy  107, 241, 242, 244, 246, 248–250, 254, 256, 260, 265 –– cost  243 –– liquefaction  148 –– nonocatalytic  149–151 –– impacts  254–265 –– environmental  265–268 –– political and economical  254–257 –– policy  253–260, 264 –– production processes  110–133 –– air-steam gasification  199–201 –– from coal  113–115 –– from natural gas by steam reforming  11 –– from hydrocarbons  111 –– from hydrogen sulfide  130 –– from water  115–119 –– photocatalytic  119 –– solar-powered  129 –– steam gasification  23, 24, 39, 114, 176, 177, 180, 197–200 –– steam reforming  176

Index –– water decomposition  116, 117, 121, 124, 126 –– water electrolysis  116, 129 –– water photocleavage  126 –– water photodecomposition  126 –– water splitting  117, 118, 120, 123, 124, 126, 129, 148, 163 –– properties  107–110 –– photocatalytic  126 –– storage of hydrogen  134–140 –– with metal hydrides  136–138 –– with boron film  139 –– with carbon structures  140 –– storage materials  141–144 M methane  13–17, 21–23, 34, 35, 44, 52, 54–56, 66, 69, 74–84, 91, 93, 106, 111–114, 133, 164, 168, 172, 193–205 methanol (methyl alcohol)  13, 14, 21, 23, 52, 65–71, 82, 83, 86–88, 93–104, 106, 109, 123, 129, 151, 221–238 N natural gas  1–18, 32, 39, 45, 56, 58, 62, 66, 67, 74, 75, 79, 80, 85–91, 104–106, 110, 111, 133, 134, 145, 177, 178 –– butane  14 –– ethane  14 –– isobutane  14 –– methane  14 –– pentane  14 –– propane  14 P petroleum  2, 5–9, 11–13, 23, 24, 39,62, 66, 67, 79, 85–89, 98–107, 145, 235, 236, 242, 243, 257, 258, 263, 265 –– API gravity  8 –– asphalt  9 –– crude oil  6, 8, 9, 13, 18, 65, 67, 83, 88, 93, 95, 101, 258, 263 –– compressed natural gas (CNG)  16, 62, 85, 86, 91, 95, 97, 103, 263 –– liquefied petroleum gas (LPG)  62, 85, 86, 89, 95, 97, 103, 233, 263 –– ligroin (light naphtha)  9 –– lubricating oil  9 –– oleum  6 –– petra  6 –– petroleum ether  9 –– shale oil (oil shale)  17, 18 –– kerogen  6, 17 –– tar sand (bitumen)  2, 4, 8, 18, 19 –– sulfur  18

Index –– viscosity  8, 10, 18 pentane  14, 89, 93 photovoltaics  3–5, 19, 106, 118, 119, 129, 236, 257, 259 –– arrays  129, 236 –– cells  94 –– hybrid system  236, 237 –– module  129 P-series fuels  98 –– methyltetrahydrofuran (MeTHF)  98 R renewable energy resources  5, 19, 46, 54 –– biomass  4, 5, 18, 21–25 –– geothermal  3–6, 18–21, 25, 27, 28, 259 –– energy  18, 27, 28 –– hydropower  3–5, 16, 18–21, 25–28, 33, 106, 245, 250, 259 –– hydram pump  33 –– hydraulic ram  33 –– microhydropower  26 –– small-scale hydropower  26 –– marine (energy)  3, 5, 6, 20, 21, 32, 174 –– ocean thermal energy  4, 33, 34 –– solar  3–5, 18–21, 25, 30–34, 39 –– energy  18, 30–34, 43, 57, 94, 106, 120, 125, 129, 146, 165–169, 179, 223, 248, 256, 259 –– photovoltaic (PV)  3, 4, 5, 19, 106, 118, 119, 129, 236, 257, 259 –– thermal  3, 5, 19, 20, 28, 30, 31, 94 –– tidal  4, 19, 20, 28, 33 –– wave  4, 19, 20, 33 –– wind  3–6, 18–21, 25, 28–31, 39, 106, 115, 233, 244 –– electricity  245 –– energy  20, 29, 115, 257, 259 –– generation  235 –– power  259 –– turbine  29 S steam gasification  23, 24, 39, 114, 176, 177, 180, 197–200, 202–214, 244–247 –– catalytic  177 steam reforming  176

275 supercapacitors  235, 236 supercritical water extraction  24, 69, 177, 206–208 supercritical water gasification  176, 177, 202–205, 214 syngas  14 –– from coal  14 V vegetable oils  22, 23, 48, 61–63, 66, 71, 74, 82, 85–88, 99, 100, 228, 259, 264 –– cracking  99, 100 –– catalytic cracking  99 –– pyrolysis  99 W water  1, 2, 15, 18, 25 –– biophotolysis  2, 166, 173, 172–174, 241 –– direct  24 –– indirect  24 –– decomposition  116, 117, 121, 124, 126 –– electrolysis  116, 129 –– solar-powered  129 –– energy  33 –– hydrogen from  2, 14, 24, 115 –– hydraulic ram (hydram) pumps  33 –– lifting force  33 –– photocleavage  126 –– photodecomposition  126 –– pumps  19 –– resources  25, 28 –– splitting  117, 118, 120, 123, 124, 126, 129, 148, 163 –– photocatalytic  125, 127, 128 –– thermochemical  131 –– water-gas  13 –– water-gas shift reaction  66, 177, 178, 191, 194, 198, 203, 205, 234, 235, 241 wood  4, 19, 21–23, 43–53, 57, 58, 63–68, 70, 79, 82, 95, 101–103, 164, 179–183, 186–188, 193–195, 199–201, 212 –– hardwood  47–50, 68, 188, 193 –– softwood  47–50, 193 –– valorization  52, 58 –– fuelwood  22, 47