USI
IE
S™
M
SCROLLSAW PATTERNS: Following are the full-size scrollsaw patterns for creating beautiful projects from ...
62 downloads
1004 Views
3MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
USI
IE
S™
M
SCROLLSAW PATTERNS: Following are the full-size scrollsaw patterns for creating beautiful projects from our CD Scrollsaw Pattern Book. Each pattern is shaded to make it easier to see where to cut and where not to cut. To navigate from page to page, simply use the vertical scrollbar on the right hand side of the screen, or the “Go To” buttons located at the top and bottom of the screen. To print, simply click on the “Printer Icon” at the top of the screen, or choose “Print” from the “File” pull-down menu. Be sure to specify which page numbers you want to print, and the number of copies. You can determine the page number from the “Page #” box 4 of 107 at the bottom of the screen. When finished, click the “First Page” button to go back to the beginning to choose another section OT I to view. C IN M ON SER
Simply click on the button of your choice. INTRO
PHOTOS
HOW-TO
MORE CD’S AVAILABLE
PATTERNS
BACK TO START
Project #1
Arch Support
Stock: 1/4”
Arch
Stock: 1/4”, cut 2
Project #1
Bottom Support Stock: 1/4”, cut 2
Stock: 1/4”
Base Support
Side Support
Drill 3/8” for turntable shaft.
Bottom Support
Side Support Stock: 1/4”, cut 2
Bottom Support
Attach Side Support with glue and finishing nails. Side Support
Side Dashed line indicates placement of Base Assembly.
Adjust slot, if necessary, for thickness of material used.
Stock: 1/4”
Top
Front/Back
Dashed lines indicate placement of Bottom Support assembly. Attach to bottomside of Top with glue or silicone.
Drill 3/8” for key
Front/Back
Small dashed lines indicate placement of Base Support.
Project #1
Side
Project #1
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Dashed line indicates placement of Turntable Overlay.
Turntable Overlay Stock: 1/4”, Secure to the Turntable with glue or silicone. Adjust slot if necessary for thickness of material used.
Side Stock: 1/4”, cut 2
Stock: 1/4”, cut 1 each
Front & Back
Attach to Base Support with glue and #18 x 5/8” finishing nails. Project #1
Figures
Stock: 1/4”
Project #2
Support Stock: 1/4”
Overlay Stock: 1/16” - 1/8”, cut 2 Attach to both sides of Support with glue.
Dashed line indicates Placement of Support.
Project #2
Figure
Stock: 1/4”
Back Crest
Stock: 1/16” - 1/8”, cut 2
Project #2
Foot Stock: 3/4”, cut 3 Top view.
Front
Fold on dashed line
Rear view
Turntable Overlay Stock: 1/4” Overlay
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Cu
Small dashed line indicates position of Turntable Overlay.
to
ut
fo
rm
us
po
ic
bo
x
si C ir tu tion cle rn o in ta f k di bl e ca e s y te ha and s fts .
Overlay
Stock: 1/4”, cut 1 each
Top/Bottom
Drill 3/8” for turntable shaft in Top and for key in Bottom.
Dashed line indicates placement of Frame on bottom of Top.
Small dashed line indicates placement of Foot on Bottom.
Cut slots for Back Crest in Top only. Adjust, if necessary, for thickness of material used.
Project #2
Project #3
Overlay Turntable Stock: 1/4”. Secure to the Turntable with super glue or silicone.
Adjust slot, if necessary, for the thickness of material used.
Project #3
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Figure Stock: 1/4”
Project #3
Dot dashed line indicates placement of Frame.
Top / Bottom Stock: 1/4”, cut 1 each Apron
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Apron
Apron
Inside small dashed line indicates placement of Apron Support on bottomside of Bottom.
Apron
45°
Apron top view
45°
Apron Stock: 1/4”, cut 4 Dashed line indicates placement of Apron. Attach Apron to Apron Support with glue. Note: bevel cut sides at 45° before cutting pattern.
Project #3
Apron Support Leg
Stock: 1/4”
Stock: 3/8”, cut 4
Attach to the bottomside of the Bottom with glue and finishing nails.
Turntable Stock: 1/4”. Countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates position of Overlay Turntable.
Project #4
Angel Stock: 1/4”
Frame Stock: 1 1/2”
es icat nd d n i a cle ey s. Cir n of k shaft itio ble pos turnta box sic u rm t fo u o Cut
Stock: 1/4”, cut 1 each
Top / Bottom
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Small dashed line indicates placement of Frame.
Dashed line indicates placement of Foot on Bottom.
Project #4
Foot Stock: 3/4”, cut 2 Top view.
Dashed line indicates position of metal turntable on bottomside.
Front
Turntable Fold on dashed line Rear view
Stock: 3/8”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Note: countersink bottomside before cutting slot.
Project #5
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Fold on dashed line Rear view
Stock: 3/4”, cut 2 Top view.
Foot
Adjust slots, if necessary, for thickness of material used.
Text Overlay Stock: 1/16’ - 1/8”
Dashed line indicates position of metal turntable on bottomside.
Figure Stock: 1/4”
Project #5
Stock: 1/4”
Arch Stock: 1/16” - 1/8”
Fence
Stock: 1/4”, cut 2
Number Overlays
Stock: 1/4”, cut 2
Arch Support
Project #5
Roundover top edge by sanding.
Cut slots for Arch Support in Top only. Adjust slot, if necessary, for thickness of material used.
Cut slots for Fence in Top only. Adjust slot, if necessary, for thickness of material used.
Stock: 1/4”, cut 1 each.
Top & Bottom
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Dashed line indicates placement of Frame.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #5
Stock: 1 1/2”
Frame
Cut out for music box
Circle indicates position of key and turntable shafts.
Project #5
Stock: 1 1/2”
Frame
Top view.
Cut out for music box
Circle indicates position of key and turntable shafts.
Project #6
Foot
Stock: 3/4”, cut 2
Front
Fold on dashed line Rear view
Project #6
Man Stock: 1/4”
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Adjust slots, if necessary, for the thickness of material used. Dashed line indicates position of metal turntable on bottomside.
Stock: 1/4”
Figure
Stock: 1/4”
Arch
Project #6
Arch Support Stock: 1/4”, cut 2
Top Attach to Top with glue and finishing nails.
Stock: 1/4”
Woman
Project #6
Dashed line indicates placement of Frame.
Small dashed line indicates placement of Foot.
Adjust slots, if necessary, for thickness of material used.
Stock: 1/4”
Bottom
Drill 3/8” for key.
Small dashed line indicates position of Top.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #6
Dashed line indicates placement of Turntable.
Stock: 1/4”
Top
Front
Drill 3/8” for turntable shaft.
Project #6
Project #7
Ceiling Stock: 1/4”. Secure on bottomside of Roof with super glue or silicone.
Adjust slots, if necessary, for the thickness of material used. Attach Angel with super glue or silicone.
Angel Stock: 1/8”, cut 3
Turntable Stock: 1/4”. Countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates position of Turntable Overlay .
Drill for 1/2”D x 5 1/4”L dowel in Ceiling and Turntable.
Top section Project #7
Bottom section
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Turntable Overlay Stock: 1/4”. Secure the Turntable Overlay with super glue or silicone.
Fold on dashed line
Stock: 3/4”, cut 2 Top view.
Foot
Front
Rear view
Project #7
Drill for a 1/2”D x 5 1/4”L dowel in Roof and Turntable Overlay.
Roof Stock: 1/4”
Drill for a 1/2”D x 5 1/4”L dowel in Roof and Turntable Overlay.
Project #7
Countersink bottomside of Bottom and atach to Frame with #6 x 3/4” screws.
Top & Bottom Stock: 1/4”, cut 1 each. Adjust slots, if necessary, for thickness of material used. Drill 3/8” in Top for turntable shaft and in Bottom for key. Small dashed line indicates placement of Foot
Dashed line indicates placement of Frame
Ornament Overlay Stock: 1/8”, cut 8
Bracket Stock: 1/8”, cut 8
Ornament Stock: 1/8”, cut 8
22.5° Sand inside edges 22.5° to fit in corner of Top view 22.5° Crest (A) & (B) on Roof.
Cut this slot for Crest (B)
Cut this slot for Crest (A)
Stock: 1/8”, cut 1 each
Crest (A) & (B)
Assembly Instructions Assemble by first attaching the Feet to the Bottom with glue or silicone. Next attach the Frame, making sure the music box movement is secure in place. Place the Top into position on the Frame, being sure all the slots for the Brackets line up before securing it in place. Then secure the Brackets in place. Now attach the Turntable Overlay to the Turntable, and then secure the metal turntable to the bottom of the Turntable. Next, secure the Ceiling to the bottom of the Roof. Then insert the dowel until it is flush with the top of the Roof and glue in place. Now secure both Crest (B) and (A) into place on the Roof, and then add the Crest Dividers. Secure the Angels into place in the Ceiling, and the Ornament Overlays and Ornaments on the tabs of the Crest and Crest Dividers. Now, secure the dowel into the Turntable assembly, and attach the metal turntable to the movement.
B
A
Stock: 1/8”, cut 4
Crest Divider
Project #7
Project #8
Figures Stock: 1/4”
Project #8
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Adjust slots if necessary for thickness of the material used.
Arch Support Stock: 1/4”, cut 2
Attach to Top with #6 x 5/8” nails and glue.
Project #8
Foot Stock: 3/4”, cut 2 Top view. Fold on dashed line Rear view
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Front
Stock: 1/4”
Arch
Project #8
Stock: 1/4”
Top
Drill 3/8” in Top for turntable shaft
Project #8
Cut slots for Arch Support. Adjust slot, if necessary, for thickness of material used.
Stock: 1/4”
Bottom
Drill 3/8” in Bottom for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #8
Project #9
Assembly Instructions Assemble by first attaching one Side Support and one Side to the Bottom. Continue in a clockwise direction with the remaining Side Supports and Sides. Next, secure the Top into position. Now attach the Lid Underlay to the bottom of the Lid. Then secure the Handles, Handle Support, Overlay, and Top Overlay into position.
30°
Top view
Side Stock: 1/4”, cut 6
Side Support Stock: 1/4”, cut 6
Note: Because copy machines are not 100% accurate, you may need to adjust the width.
30°
Note: Most copy machines are not 100% accurate, which can result in distortion of your pattern pieces. Since this project has several slots and tab connections, it may be necessary to adjust them for an accurate fit. Project #9
Top Stock: 1/4”
Lid Underlay . Use #60 drill bit to start cut for Lid Underlay.
Stock: 1/4” Note: after cuttung the interior section, use it as the Lid Underlay. Cut or sand slightly smaller before securing to the bottom of the Lid. This will help the Lid fit easier into position.
Top Overlay Stock: 1/8”. Attach to Overlay with glue.
Project #9
Drill for finial or brass knob of your choice.
Bottom Stock: 1/4”
Dashed line indicates position of music movement.
Drill 3/8” for key
Adjust slots, if necessary, for the thickness of material used.
Project #9
Overlay Stock: 1/8”
Handle Support Stock: 1/4”
Lid Stock: 1/4”
Handle Stock: 1/8”, cut 3
Dashed line indicates placement of Lid Underlay.
Top Handle Stock: 1/4”
Bottom Handle Stock: 1/4”
Side Stock: 1/4”, cut 2
Attach to End with glue and finishing nails.
End Stock: 1/4”, cut 2
Project #10
Lid Support Stock: 1/8” Attach to bottomside of Lid with glue or silicone.
Foot
Front
Stock: 3/4”, cut 4 Top view.
Handle Support Stock: 1/4”. Attach to Lid with glue or silicone.
Fold on dashed line Rear view Roundover top edges by sanding.
Stock: 1/4”
Bottom
End Side
Adjust slot, if necessary for the thickness of material
Assemble by first attaching the Sides to the Ends. Then secure this assembly to the Bottom. Attach the Lid support to the bottomside of the Lid, and then attach the Handle Support and Handle. Now attach the Feet with glue and finishing nails, or silicone. And finally, secure the music movement in place.
Assembly Instructions
Small dashed line indicates position of music movement
Drill 3/8” hole for key.
Side
Dashed line indicates placement of Foot.
Project #10
End
Project #10
End
Stock: 1/4”
Lid
Side
Side
Small dashed line indicates placement of Handle Support
End
Attach Ends with glue and finishing nails.
Stock: 1/4”, cut 2
End
Stock: 1/4”, cut 2
Side
Use hinges of your choice to attach the Lid to the back Side.
Project #11
Foot Front
Stock: 3/4”, cut 4
Top view.
Fold on dashed line Rear view
Stock: 1/4
Lid Use hinges of your choice to attach the Lid to the back Side.
Project #11
Drill 3/8” hole for key.
Assemble by first attaching the Sides to the Ends. Next, attach this assembly to the Bottom. Now attach the hinges of your choice to the back Side and Lid, being careful not to allow screws to protrude through the Side or Lid. It may be necessary to sand or file screws before attaching hinges. Secure the Feet in position, and finally secure the music box movement into place.
Assembly Instructions
Stock: 1/4
Bottom
End Side
Adjust slots, if necessary, for thickness of material used.
Small dashed line indicates position of music movement
Side
Small dashed line indicates
Project #11
End
End
Stock: 1/4”
Lid
Side
Side
Use hinges of your choice to attach the Lid to the back Side.
Project #12
End
Stock: 1/4”, cut 2
Side
Stock: 1/4”, cut 2
End
Attach Ends with glue and finishing nails. Use hinges of your choice to attach the Lid to the back Side.
Project #12
Foot Front
Stock: 3/4”, cut 4
Top view.
Fold on dashed line Rear view
End
Drill 3/8” hole for key.
Assemble by first attaching the Sides to the Ends. Next, attach this assembly to the Bottom. Now attach the hinges of your choice to the back Side and Lid, being careful not to allow screws to protrude through the Side or Lid. It may be necessary to sand or file screws before attaching hinges. Secure the Feet in position, and finally secure the music box movement into place.
Assembly Instructions
Stock: 1/4”
Bottom
Side
Dashed line indicates placement of Foot.
Small dashed line indicates position of music movement
Side
Project #12
End
Stock: 1/4”, cut 2
End
Stock: 1/4”, cut 2
Side
Attach Ends with glue and finishing nails. Use hinges of your choice to attach the Lid to the back Side.
Project #13
Foot Front
Stock: 3/4”, cut 4
Top view.
Fold on dashed line Rear view
End
Stock: 1/4”
Lid
Side
Side
Use hinges of your choice to attach the Lid to the back Side.
Project #13
End
End
Assemble by first attaching the Sides to the Ends. Next, attach this assembly to the Bottom. Now attach the hinges of your choice to the back Side and Lid, being careful not to allow screws to protrude through the Side or Lid. It may be necessary to sand or file screws before attaching hinges. Secure the Feet in position, and finally secure the music box movement into place.
Assembly Instructions
Drill 3/8” hole for key.
Stock: 1/4”
Bottom
Side
Adjust slots, if necessary, for thickness of material used.
Small dashed line indicates position of music movement
Side
Dashed line indicates placement of Foot.
Project #13
End
Project #14
Arch Support Stock: 1/4”, cut 2
Top Attach Arch Support to Top with glue and finishing nails.
Pattern overlap line.
Pattern overlap line.
Project #14
Figure Stock: 1/4”
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates placement of Turntable Overlay.
Foot Stock: 3/4”, cut 2 Top view.
Project #14
Fold on dashed line
Top Stock: 1/4”
Drill 3/8” in Top for turntable shaft.
Front
Rear view
Dashed line indicates position of Frame
Turntable Overlay Stock: 1/4” Project #14
Adjust slot, if necessary, for thickness of material used.
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” in Bottom for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #14
Arch Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Stock: 1 1/2”
Frame
Cut out for music box
Circle indicates position of key and turntable shafts.
Assembly Instructions To Assemble, attach Legs to Apron Support with glue. Next, attach the Aprons. Then clamp this assembly to the bottomside of the Bottom and countersink to attach the assembly to the Frame with #6 x 1” F.H. screws.
Project #15
Project #15
Arch Support Stock: 1/4”, cut 2
Turntable Stock: 1/4”. Countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. 45°
Side Apron top view
Side Apron Stock: 3/8”, cut 2
Stock: 1/4”
Dashed line indicates position of metal turntable on bottomside.
Apron Support
Roundover top edge by sanding.
45°
Dashed line indicates placement of Apron. Attach Apron to Apron Support with glue.
Project #15
Front / Back Apron
Stock: 1/4”, cut 2
45°
Dashed line indicates placement of Apron. Attach Apron to Apron Support with glue.
Front/Back 45° Apron top view
Cut slots to attach to Arches. Adjust slots, if necessary, for thickness of material used.
Stock: 3/8”, cut 1 each.
Roof
Cut slots for Arch Supports. Adjust, if necessary, for thickness of material used.
Stock: 1/4”
Top
Drill 3/8” for turntable shaft.
Dashed line indicates placement of Frame on bottom of Top.
Project #15
g Le
Side Apron
Le g
Side Apron
Front/Back Apron
Drill 3/8” for key
Inside small dashed line indicates placement of Apron Support
Dashed line indicates placement of Frame on top of Bottom.
Stock: 1/4”
Bottom
Front/Back Apron
g Le
Le g
Project #15
Project #15
Fill gap with 3/8” dowel.
Stock: 3/8”
Leg
Ro o
f
Stock: 3/8”, cut 4
Arch
Ro of
Stock: 3/8”
Stock: 1/4”, cut 2
Stock: 3/8”
Project #16 - #18
Figure Stock: 3/8”
Dashed line indicates position of metal turntable on bottomside.
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Dashed line indicates position of Frame.
Cut slots in Top only. Adjust slot, if necessary, for thickness of material used.
Stock: 1/4”, cut 1 each.
Top / Bottom
Small dashed line indicates position of Foot on Bottom.
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #16 - #18
Arch Support
Stock: 1/4”, cut 2
Project #16 - #18
Cut out for music box
Stock: 3/4”, cut 2 Top view.
Figure Stock: 3/8”
Stock: 1 1/2”
Frame
Fold on dashed line Rear view
Circle indicates position of key and turntable shafts.
Front
Foot
Stock: 1/4”
Arch
Project #16 - #18
Figure Stock: 3/8”
Project #19
Cathedral Music Box Description item Qty Front Wall Back Wall Wall Anchor Side Wall Front & Back Base Base Side Front & Back Spire Spire Side Floor Bottom Support Side Support Ceiling Turntable Turntable Overlay Figure
A B C D E F G H I J K L M N O
1 1 4 2 1 each 2 1 each 2 1 2 2 1 1 1 1
H
G
L
B
A
D
C Ceiling (L)
O
Stock: 1/8”
N
M I J
K F E
Front
Bottom Support
Side Support (K) Stock: 1/4”, cut 2
Turntable Overlay (N) Stock: 1/4” Attach to Turntable with glue.
Bottom Support
Project #19
Front Wall (A) Stock: 1/8”
Wall Anchor (C) Stock: 1/8”, cut 4
Insert Wall Anchor tab here.
Assembly instructions Assemble by first inserting the Base Side tabs into the Front and Back Base and secure with glue. Next, attach the Side Supports to the Bottom Supports to hold the music box movement. Attach this assembly to the bottom of the Floor with glue or silicone. Now attach the Base assembly to the Floor. Then attach the Figure to the Turntable Assembly and then secure to the metal turntable in the music box movement. Next attach the Side Walls to the Front and Back Walls, and secure this assembly to the Floor. Now secure the Wall Anchors and Ceiling into place. Then attach the Spire Sides to the front and Back Spires, and secure this assembly into place on the Ceiling.
Insert Wall Anchor tab here.
Project #19
Back Wall (B) Stock: 1/8”
Project #19
Stock: 1/8”, cut 2
Base Side (F)
Ceiling tab fits here
Figure (O) Stock: 1/4”
Side Wall (D) Stock: 1/8”, cut 2
Project #19
Front & Back Base (E) Stock: 1/8”, cut 1 each
Front & Back Spire (G) Stock: 1/8”, cut 1 each
Spire Side (H) Stock: 1/8”, cut 2
Project #19
Floor (I)
Insert Back Wall tab here. Dashed lines indicate placement of Bottom Support assembly. Attach to bottomside of Floor with glue or silicone.
Insert Base Side tabs here.
Stock: 1/4”
Drill 3/8” turntable shaft.
Insert Front Wall tab here.
Front
Turntable
Small dashed line indicates position of Turntable Overlay.
Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Bottom Support (J)
Drill 3/8” for key. Attach Side Supports with glue and finishing nails.
Side Support
Side Support
Stock: 1/4”, cut 2
Project #20
Frame Stock: 1 1/2” Circle indicates position of key and turntable shafts.
Cut out for music box
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Small dashed line indicates placement of Foot on Bottom. Drill 3/8” for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #20
Top Rim Stock: 1/8” - 1/4” Attach to Top with glue or silicone.
Small dashed line indicates placement of Top
Top Stock: 1/8” - 1/4” Attach to Frame with glue and finishing nails or silicone.
Foot Stock: 3/4”, cut 2
Front
Top view. Fold on dashed line
Rear view
Dashed line indicates placement of Frame
Frame Stock: 1 1/2”
Project #21
Circle indicates position of key and turntable shafts.
Cut out for music box
Bottom
Dashed line indicates position of Frame
Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #21
Top Rim Stock: 1/8” - 1/4” Attach to Top with glue or silicone.
Small dashed line indicates placement of Top
Top
Rear view
Fold on dashed line.
Stock: 3/4”, cut 2
Foot
Front
Top view
Stock: 1/8” - 1/4” Attach to Frame with glue and finishing nails or silicone.
Dashed line indicates placement of Frame
Project #22
Frame Stock: 1 1/2” Circle indicates position of key and turntable shafts.
Cut out for music box
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #22
Top Rim Stock: 1/8” - 1/4” Attach to Top with glue or silicone.
Small dashed line indicates placement of Top
Top
Fold on dashed line
Stock: 3/4”, cut 2 Top view.
Foot
Front
Rear view
Stock: 1/8” - 1/4” Attach to Frame with glue and finishing nails or silicone.
Dashed line indicates placement of Frame
Project #23
Frame Stock: 1 1/2” Circle indicates position of key and turntable shafts.
Cut out for music box
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #23
Top Rim Stock: 1/8” - 1/4” Attach to Top with glue or silicone.
Small dashed line indicates placement of Top
Top
Fold on dashed line
Top view.
Stock: 3/4”, cut 2
Foot
Front
Rear view
Stock: 1/8” - 1/4” Attach to Frame with glue and finishing nails or silicone.
Dashed line indicates placement of Frame
Project #24 Front Top view. Fold on dashed line. Rear view
Foot Stock: 3/4”, cut 3
Bottom Stock: 1/4”
Dashed line indicates placement of Frame
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Small dashed lines indicate placement of Foot.
Project #24
Frame Stock: 1 1/2”
Cut out for music box
Circle indicates position of key and turntable shafts.
Top Stock: 1/4”
Project #25
Front
Foot Stock: 3/4”, cut 2 Top view Fold on dashed line
Rear view
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Top
Project #25
Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Foot
Front Project #26
Stock: 3/4”, cut 2 Top view. Fold on dashed line Rear view
Bottom Stock: 1/4”
Drill 3/8” for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Dashed line indicates position of Frame
Project #26
Top Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #27
Foot Stock: 3/4”, cut 2 Top view.
Fold on dashed line
Front
Rear view
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #27
Top Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #28
Front
Foot
Top view.
Stock: 3/4”, cut 2 Fold on dashed line Rear view
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” in Bottom for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #28
Top Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #29
Front
Foot Stock: 3/4”, cut 2 Top view.
Rear view
Fold on dashed line
Bottom
Dashed line indicates position of Frame
Stock: 1/4”
Small dashed line indicates placement of Foot. Drill 3/8” for key.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #29
Top Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #30
Foot
Front
Stock: 3/4”, cut 2 Top view. Fold on dashed line
Rear view
Dashed line indicates position of Frame
Bottom Stock: 1/4”
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #30
Top Stock: 1/4”
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #31
Turntable Overlay Stock: 1/4”. Attach to Turntable with glue or silicone. Drill 1/4” hole for dowel.
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #31
Top Top Stock: 1/4” Figure
Figure Stock: 1/4”
Drill for a 1/4”D x 3 1/2” long dowel. Secure in Figure and Turntable with glue.
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates position of Turntable Overlay.
Front
Top view.
Foot Stock: 3/4”, cut 2 Fold on dashed line Rear view
Top & Bottom Stock: 1/4”, cut 1 each
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Dashed line indicates position of Frame
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #31
Project #32
Dashed line indicates placement of Frame.
Top & Bottom Stock: 1/4”, cut 1 each. Cut slots in Top only
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Small dashed line indicates placement of Foot.
Top
1
3/4”
Foot
Stock: 3/4”, cut 3 Front
2 Rear
view Back
1 3/16”
Top view. Fold on dashed line Rear view
Figure Stock: 1/4”
3
Top view
Top
Project #32
Pinnacle #2 Stock: 1/4”
Pinnacle #1 Stock: 1/4”
Roof Stock: 1/4”
Project #32
Turntable Overlay Stock: 3/8”
Roundover top edge by sanding
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Dashed line indicates position of metal turntable on bottomside. Small dashed line indicates placement of Turntable Overlay.
Frame Stock: 1 1/2”
Roof Support Stock: 1/4”, cut 4 Circle indicates position of key and turntable shafts.
Cut out for music box
Project #33
Turntable Overlay Stock: 1/4”. Attach to Turntable with glue or silicone. Drill 1/4” hole for dowel.
Frame Stock: 1 1/2”
Circle indicates position of key and turntable shafts.
Cut out for music box
Project #33
Front
Top view.
Foot Stock: 3/4”, cut 2 Fold on dashed line Rear view
Top & Bottom Stock: 1/4”, cut 1 each
Drill 3/8” in Top for turntable shaft and in Bottom for key.
Dashed line indicates position of Frame
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #33
Body
Mane
Drill for a 1/4”D x 3 1/2” long dowel. Secure in Body and Turntable with glue.
Front Leg Stock: 1/8” - 1/4”, cut 2
Stock: 1/16” - 1/8” , cut 2. Attach with glue or silicone.
Stock: 3/8”
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates position of Turntable Overlay.
Back Leg Stock: 1/8” - 1/4”, cut 2
Corner Tulips
Bouquet
Corner Tulips
Drill 3/8” for turntable shaft.
Front/Back
Dashed lines indicate placement of Bottom Support assembly. Attach to bottomside of Top with glue or silicone.
Stock: 1/4”
Top
Front/Back
Small dashed lines indicates placement of Apron Support.
Corner Tulips
Bouquet
Corner Tulips Project #34
Side
Side
Project #34
Turntable Overlay Stock: 1/4”, Secure to the Turntable with glue or silicone.
Adjust slot if necessary for thickness of material used.
Turntable Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.
Corner Tulips Stock: 3/8”, Cut 4. Secure to Top with glue or silicone.
Dashed line indicates placement of Turntable Overlay.
Stock: 1/4”, cut 1 each
Front & Back
Attach Apron Support with glue and finishing nails.
Project #34
Bouquet
Stock: 3/8”, cut 2
Bottom Support
Side Support
Stock: 1/4”, cut 2
Bottom Support
Side Support
Drill 3/8” for key.
Side Support
Stock: 1/4”. Attach to bottomside of Top with glue or silicone.
Apron Support
Assembly Instructions Assemble by first attaching the Sides to the Front and Back. Next attach the Apron Support. Now attach the Bottom Supports to the Side Supports. Insert the music box movement and secure in place with silicone. Attach the Leg assembly to the bottom of the Top and secure with glue or silicone. Insert the music box movement assembly into position on the underside of the Top and glue in place. Secure the Turntable Overlay to the Turntable and secure the figures into place. Then attach the wood Turntable to the metal turntable.
Project #34
Bottom Support
Stock: 1/4”, cut 2
Project #34
Side Stock: 1/4”, cut 2
Figure Stock: 1/4”
Project #35 - 58
Foot Stock: 3/4”, cut 2 Top view.
Front
Fold on dashed line Rear view
Top & Bottom
Stock: 1/4”, cut 1 each Dashed line indicates position of Frame
Drill 3/8” for key.
Small dashed line indicates placement of Foot on Bottom.
Countersink bottomside of Bottom and attach to Frame with #6 x 3/4” screws.
Project #35-58
Turntable Stock: 1/4”. Countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone. Dashed line indicates position of metal turntable on bottomside.
Small dashed line indicates position of Overlay Turntable.
Frame Stock: 1 1/2” Circle indicates position of key and turntable shafts.
Cut out for music box
Project #35-58
Bird & Hearts Stock: 3/8”
Cupid & Harp Stock: 3/8”
Victorian Heart Stock: 3/8”
Angel & Birds Stock: 3/8”
Project #35-58
Roses Stock: 3/8”
Gal Stock: 3/8”
Horse Stock: 3/8”
Candles Stock: 3/8”
Project #35-58
Angel Stock: 3/8”
Singer Stock: 3/8”
Flowers Stock: 3/8”
Love Birds Stock: 3/8”
Project #35 - 58
Angel Stock: 3/8”
Cupid Stock: 3/8”
Messenger Valentine Stock: 3/8”
Stock: 3/8”
Project #35-58
Gentleman Stock: 3/8”
Lady Stock: 3/8”
Sweet Couple Stock: 3/8”
Flowery Heart Stock: 3/8”
